Статья 22Директива № 2009/34/ЕС Европейского парламента и Совета Европейского Союза

Настоящая Директива адресована государствам-членам ЕС.

Совершено в Страсбурге 23 апреля 2009 г.

(Подписи)

УТВЕРЖДЕНИЕ ТИПА ЕС

1.1. Заявление и корреспонденция, относящаяся к нему, должны составляться на официальном языке в соответствии с законодательством государства-члена ЕС, в которое подается заявление. Государство-член ЕС имеет право запрашивать прилагаемые документы, составленные на том же официальном языке.

Одновременно с этим заявитель должен разослать копию своего заявления всем государствам-членам ЕС.

a) название и адрес изготовителя или компании или его или ее уполномоченного представителя или заявителя;

b) тип прибора;

c) назначение использования;

d) измерительные характеристики;

e) коммерческое обозначение, если имеется, или вид.

1.3. К заявлению должны быть приложены в двух экземплярах документы, необходимые для его оценки, а именно:

1.3.1. описание, в частности:

a) конструкции и эксплуатации прибора;

b) защитных механизмов, обеспечивающих правильную работу;

c) устройств для регулирования и настройки;

d) мест, предназначенных для:

• маркировок проверки;
• пломбы (при необходимости).

1.3.2. общие чертежи и при необходимости чертежи важных деталей;

1.3.3. схематический эскиз, иллюстрирующий принципы эксплуатации, если необходимо, фотография.

1.4. К заявлению по возможности должны быть приложены документы, касающиеся национальной сертификации.

2.1.1. изучение документации и проверку измерительных характеристик образца в лаборатории метрологической службы в установленной лаборатории или месте изготовления, доставки или установки;

2.1.2. если измерительные характеристики известны в деталях, то возможно проведение изучения документации.

2.2. Экспертиза должна быть проведена на протяжении всей работы прибора при нормальных условиях. При таких условиях прибор должен обладать требуемыми характеристиками.

2.3. Характер и масштаб проверочных мероприятий, упомянутых в пункте 2.1, должны быть установлены отдельными директивами.

2.4. Метрологическая служба может потребовать от заявителя предоставить в его распоряжение стандарты и необходимые с его точки зрения материалы и вспомогательный персонал для осуществления испытаний.

3.1. Сертификат должен отражать результаты проверки образца и другие требования, которые должны быть выполнены. К нему должны быть приложены описания, чертежи и диаграммы, необходимые для идентификации образца и объяснения принципов его работы. Знак утверждения типа, предусмотренный в статье 4, должен быть выполнен в виде буквы «эпсилон» и содержать:

• в верхней части — отличительные буквы(-у) государства-члена ЕС, выдавшего утверждение (B — Бельгия, BG — Болгария, CZ — Чешская Республика, DK — Дания, D — Германия, EST — Эстония, IRL — Ирландия, EL — Греция, E — Испания, F — Франция, I — Италия, CY — Кипр, LV — Латвия, LT — Литва, L — Люксембург, H — Венгрия, M — Мальта, NL — Нидерланды, A — Австрия, PL — Польша, P — Португалия, RO — Румыния, SI — Словения, SK — Словакия, FL — Финляндия, S — Швеция, UK — Соединенное Королевство) и две последние цифры года, когда оно выдано;
• в нижней части — обозначение, которое означает метрологическую службу, которая выдала утверждение (идентификационный номер).

Пример такого знака утверждения показан в пункте 6.1.

3.2. В случае если утверждение имеет ограничение по времени действия, рядом с буквой «эпсилон» должна быть размещена буква P, которая имеет те же размеры.

Пример такого знака временного утверждения показан в пункте 6.2.

3.3. Знак, упомянутый в статье 6, является тем же, что и знак утверждения ЕС, за исключением буквы «эпсилон», которая развернута симметрично своей вертикальной оси и не имеет других знаков, если отдельной директивой не предусмотрено иное.

Пример такого знака временного утверждения показан в пункте 6.3.

3.4. Знак, упомянутый в статье 11, является тем же знаков утверждения, заключенным в шестиугольник.

Пример такого знака временного утверждения показан в пункте 6.4.

3.5. Знаки, упомянутые в пунктах 3.1. - 3.4., наносятся изготовителем в соответствии с требованиями настоящей Директивы, а именно должны находиться на видном месте каждого прибора и вспомогательного оборудования, которые подлежат проверке, должны быть четкими и нестираемыми. Если нанесение знаков трудоемко с технической стороны, исключения могут быть предусмотрены положениями отдельных директив после достигнутого соглашения между метрологическими службами государств-членов ЕС.

В случаях, предусмотренных отдельными директивами, служба, которая утвердила тип, может, если посчитает это необходимым, запросить образец утвержденного прибора для депонирования. Вместо образца прибора служба может разрешить депонирование частей прибора, масштабных моделей или чертежей и укажет это на выданном сертификате.

5.1. В то же время, что и заинтересованной стороне, копии сертификата утверждения ЕС быть направлены Европейской комиссии и другим государствам-членам ЕС; последние могут получить копии протоколов метрологических исследований при необходимости.

5.2. Отзыв сертификата утверждения типа ЕС и иные действия, связанные с продлением и сроком действия сертификата должны тем же образом, который описан в пункте 5.1., доводиться до тех же корреспондентов.

5.3. Государство-член ЕС, отказавшееся выдавать утверждение типа, должно проинформировать другие государства-члены ЕС и Европейскую комиссию о своем решении.

Пример: <*> Знак утверждения типа, выданный Метрологической службой Германии в 1971 году (см. пункт 3.1, первый абзац).

---

<*> Рисунок не приводится.

Идентификационный номер утверждения типа ЕС (см. пункт 3.1, второй абзац).

Пример: <*> Знак утверждения типа, выданный Метрологической службой Германии в 1971 году .

---

<*> Рисунок не приводится.

Идентификационный номер утверждения типа ЕС ограниченного действия.

Пример: <*>

---

<*> Рисунок не приводится.

Пример: <*> Знак утверждения типа, выданный Метрологической службой Германии в 1971 году.

---

<*> Рисунок не приводится.

Идентификационный номер утверждения типа ЕС.

ПЕРВОНАЧАЛЬНАЯ ПРОВЕРКА ЕС

1.1. Первоначальная проверка ЕС может проходить в один или более этапов (обычно два).

1.2.1. проверка должна проводиться в один этап по отношению к приборам, которые являются финальной продукцией изготовителя и теоретически могут быть перевезены к месту своей установки без демонтажа;

1.2.2. проверка должна проводиться в два этапа для приборов, правильное функционирование которых зависит от условий установки или использования;

1.2.3. первый этап проверки должен проверить, соответствует ли образец утвержденному типу, если да, то в этом случае они освобождаются от утверждения типа в связи с тем, что соответствуют требованиям.

2.1. Если отдельными директивами не определено место для проведения первоначальной проверки ЕС, то приборы, подлежащие проверке в один этап, должны проходить ее в месте, определенном метрологической службой.

2.2. Приборы, которые должны проходить проверку в два и более этапа, должны быть проверены компетентной на той территории метрологической службой.

2.2.1 Последний этап проверки должен проходить в месте установки.

2.2.2. Иные этапы проверки должны проходить в соответствии с положениями пункта 2.1.

2.3. В частности, если проверка проводится за пределами территории метрологической службы, последняя может запросить у заявителя:

• в свое распоряжение образцы и соответствующие средства — материал и вспомогательный персонал для проведения проверки;
• предоставление копии сертификата утверждения ЕС.

3.1.1. В соответствии с отдельными директивами знаки первоначальной проверки ЕС, которые закрепляются в соответствии с пунктом 3.3, должны иметь следующий вид:

3.1.1.1. окончательный знак проверки ЕС должен состоять из двух оттисков:

a) первый состоит из строчной буквы «e», содержащей:

• в верхней части — отличительные буквы(-у) государства-члена ЕС, выдавшего утверждение (B — Бельгия, BG — Болгария, CZ — Чешская Республика, DK — Дания, D — Германия, EST — Эстония, IRL — Ирландия, EL — Греция, E — Испания, F — Франция, I — Италия, CY — Кипр, LV — Латвия, LT — Литва, L — Люксембург, H — Венгрия, M — Мальта, NL — Нидерланды, A — Австрия, PL — Польша, P — Португалия, RO — Румыния, SI — Словения, SK — Словакия, FL — Финляндия, S — Швеция, UK — Соединенное Королевство) и при необходимости одну или две цифры, идентифицирующие территориальный или административный округ;
• в нижней части — идентификационный номер проверяющего агентства или службы.

3.1.1.2. Знак ЕС частичной проверки должен состоять только из первого оттиска. Он также должен служить в качестве печати.

3.2.1. Прилагаемые чертежи <*> показывают форму, размеры и контуры букв и цифр для первоначальной проверки ЕС, установленной в пункте 3.1; первые два чертежа иллюстрируют разные части штампа, третий — сам штамп. Размеры, представленные на чертеже, являются относительными значениями; они зависят от диаметра круга строчной буквы «e» и от размера шестиугольника.

---

<*> Не приводятся.

Фактический размер кругов, описывающих маркировку — 1,6 мм, 3,2 мм, 6,3 мм, 12,5 мм.

3.2.2. Метрологические службы государств-членов ЕС должны обмениваться оригинальными чертежами знака первоначальной проверки ЕС в соответствии с моделями в приложенных чертежах.

3.3.1. Окончательный знак проверки ЕС должен быть нанесен на предназначенное для этого место на приборе, который был полностью проверен и признан отвечающим требованиям ЕС.

3.3.2 Частичный знак проверки ЕС должен быть нанесен:

3.3.2.1. когда проверка совершается в несколько этапов, на прибор или его часть, которые отвечают требованиям, установленным для операций, отличных от тех, которые проходят на месте установки, в том месте, где проставляется штамп даты или ином другом месте, определенном отдельными директивами;

3.3.2.2. во всех случаях в качестве печати в местах, определенных отдельными директивами.

Директива 71/316/ЕЭС Совета ЕС (ОЖ № L 202, 6.9.1971, стр. 1).

Акт о присоединении 1972 г., Приложение I, пункт X.12 (ОЖ № L 73, 27.3.1972, стр. 118).

Директива 72/427/ЕЭС Совета ЕС (ОЖ № L 291, 28.12.1972, стр. 156).

Акт о присоединении 1979 г., Приложение I, пункт X.A (ОЖ № L 291, 19.11.1979, стр. 108).

Директива 83/575/ЕЭС Совета ЕС (ОЖ № L 332, 28.11.1983, стр. 43).

Акт о присоединении 1985 г., Приложение I, пункт IX.A.7 (ОЖ № L 302, 15.11.1985, стр. 212).

Директива 87/354/ЕЭС Совета ЕС              Только в отношении ссылки на
(ОЖ N L 192, 11.7.1987, стр. 43).           Директиву 71/316/ЕЭС в статье 1

                                        и в пункте 4 Приложения

Директива 87/355/ЕЭС Совета ЕС (ОЖ № L 192, 11.7.1987, стр. 46).

Директива 88/665/ЕЭС Совета ЕС Только статья 1 (1) (ОЖ № L 382, 31.12.1988, стр. 42).

Акт о присоединении 1994 г., Приложение I, пункт XI.C.VII.I (ОЖ № C 241, 29.8.1994, стр. 211).

Регламент (ЕС) 807/2003 Совета ЕС Только Приложение III, пункт 5 (ОЖ № L 122, 16.5.2003, стр. 36).

Акт о присоединении 2003 г., Приложение II, пункт I.D.I (ОЖ № L 236, 23.9.2003, стр. 64).

Директива 2006/96/ЕС Совета ЕС              Только в отношении ссылки на
(ОЖ N L 363, 20.12.2006, стр. 81).          Директиву 71/316/ЕЭС в статье 1

                                        и в пункте B.1 Приложения

Директива 2007/13/ЕС Европейской комиссии (ОЖ № L 73, 13.3.2007, стр. 10)

Директива	Временные рамки для преобразования в национальное право
71/316/ЕЭС	30 января 1973 г.
83/575/ЕЭС	1 января 1985 г.
87/354/ЕЭС	31 декабря 1987 г.
87/355/ЕЭС	31 декабря 1987 г.
2006/96/ЕС	1 января 2007 г.
2007/13/ЕС	9 марта 2008 г.

Приложение IV

Директива 71/316/ЕЭС	Настоящая Директива
Статья 1 (1) «a»	Статья 1 (1), пункт «a» и статья 1 (2)
Статья 1 (1) «b»	Статья 1 (1), пункт «b»
Статья 1 (1) «c»	Статья 1 (1), пункт «c»
Статья 1 (2)	Статья 1 (3)
Статья 1 (3)	Статья 1 (4)
Статья 1 (4), первый подпараграф	Статья 1 (5)
Статья 1 (4), второй подпараграф	Статья 1 (6)
Статья 2 (1)	Статья 2 (2)
Статья 2 (2)	Статья 2 (3)
Статья 2 (3)	Статья 2 (4)
Статья 2 (4)	Статья 2 (5)
Статья 2 (5)	Статья 2 (1)
Статья 3, вступительная часть	Статья 3, вступительная часть
Статья 3, первый абзац	Статья 3, пункт «a»
Статья 3, второй абзац	Статья 3, пункт «b»
Статья 4, первое предложение	Статья 4, первый и второй параграфы
Статья 4, второе предложение	Статья 4, третий параграф
Статья 5 (1)	Статья 5 (1)
Статья 5 (2), первый подпараграф	Статья 5 (2), первый подпараграф
Статья 5 (2), второй подпараграф, вступительная часть	Статья 5 (2), второй подпараграф, вступительная часть
Статья 5 (2), второй подпараграф, первый абзац	Статья 5 (2), второй подпараграф, пункт «a»
Статья 5 (2), второй подпараграф, второй абзац	Статья 5 (2), второй подпараграф, пункт «b»
Статья 5 (2), второй подпараграф, третий абзац	Статья 5 (2), второй подпараграф, пункт «c»
Статья 5 (2), второй подпараграф, четвертый абзац	Статья 5 (2), второй подпараграф, пункт «d»
Статья 5 (2), третий подпараграф, вступительная часть	Статья 5 (2), третий подпараграф, вступительная часть
Статья 5 (2), третий подпараграф, первый абзац	Статья 5 (2), третий подпараграф, пункт «a»
Статья 5 (2), третий подпараграф, второй абзац	Статья 5 (2), третий подпараграф, пункт «b»
Статья 5 (2), четвертый подпараграф	Статья 5 (2), четвертый подпараграф
Статья 5 (3)	Статья 5 (3)
Статья 6	Статья 6
Статья 7 (1), (2) и (3)	Статья 7 (1), (2) и (3)
Статья 7 (4), первое предложение	Статья 7 (4), первый подпараграф
Статья 7 (4), второе предложение	Статья 7 (4), второй подпараграф
Статья 7 (4), третье предложение	Статья 7 (4), третий подпараграф
Статья 7 (5)	Статья 7 (5)
Статья 8 (1), пункт «a»	Статья 8 (1)
Статья 8 (1), пункт «b»	Статья 8 (2)
Статья 8 (2)	Статья 8 (3)
Статья 8 (3)	Статья 8 (4)
Статья 9 (1)	Статья 9 (1)
Статья 9 (2), вступительная часть	Статья 9 (2), вступительная часть
Статья 9 (2), первый абзац	Статья 9 (2), пункт «a»
Статья 9 (2), второй абзац	Статья 9 (2), пункт «b»
Статья 9 (2), третий абзац	Статья 9 (2), пункт «c»
Статья 9 (2), четвертый абзац	Статья 9 (2), пункт «d»
Статьи 10 и 11	Статьи 10 и 11
Статьи 12, 13 и 14	Статьи 12, 13 и 14
Статья 15	Статья 15
Статья 16, первое предложение	Статья 16, первый подпараграф
Статья 16, второе предложение	Статья 16, второй подпараграф
Статья 17	-
Статья 18 (1)	Статья 17 (1)
Статья 18 (2), первый подпараграф	Статья 17 (2)
Статья 18 (2), второй подпараграф	-
Статья 18 (3)	-
Статья 19	Статья 18
Статья 20 (1)	-
Статья 20 (2) -	Статья 19 Статьи 20 и 21
Статья 21	Статья 22
Приложение I	Приложение I
Пункты 1 и 1.1	Пункты 1 и 1.1
Пункт 1.2, вступительная часть	Пункт 1.2, вступительная часть
Пункт 1.2, первый абзац	Пункт 1.2 «a»
Пункт 1.2, второй абзац	Пункт 1.2 «b»
Пункт 1.2, третий абзац	Пункт 1.2 «c»
Пункт 1.2, четвертый абзац	Пункт 1.2 «d»
Пункт 1.2, пятый абзац	Пункт 1.2 «e»
Пункт 1.3	Пункт 1.3
Пункт 1.3.1, вступительная часть	Пункт 1.3.1, вступительная часть
Пункт 1.3.1, первый абзац	Пункт 1.3.1 «a»
Пункт 1.3.1, второй абзац	Пункт 1.3.1 «b»
Пункт 1.3.1, третий абзац	Пункт 1.3.1 «c»
Пункт 1.3.1, четвертый абзац	Пункт 1.3.1 «d»
Пункт 1.3.2 до пункта 5	Пункт 1.3.2 до пункта 5
Пункт 5.2	Пункт 5.1
Пункт 5.3	Пункт 5.2
Пункт 5.4	Пункт 5.3
Пункт 6 до пункта 6.4	Пункт 6 до пункта 6.4
Приложение II — -	Приложение II Приложение III Приложение IV

DIRECTIVE No. 2009/34/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL RELATING TO COMMON PROVISIONS FOR BOTH MEASURING INSTRUMENTS AND METHODS OF METROLOGICAL CONTROL (RECAST)

The European Parliament and the Council of the European Union,

Having regard to the Treaty establishing the European Community, and in particular Article 95 thereof,

Having regard to the proposal from the Commission,

Having regard to the opinion of the European Economic and Social Committee <*>,

---

<*> Opinion of 22 October 2008 (not yet published in the Official Journal).

Acting in accordance with the procedure laid down in Article 251 of the Treaty <*>,

---

<*> Opinion of the European Parliament of 4 December 2008 (not yet published in the Official Journal) and Council Decision of 23 March 2009.

Whereas:

(1) Council Directive 71/316/EEC of 26 July 1971 on the approximation of the laws of the Member States relating to common provisions for both measuring instruments and methods of metrological control <*> has been substantially amended several times <**>. Since further amendments are to be made, it should be recast in the interests of clarity.

---

<*> OJ L 202, 6.9.1971, p. 1.

<**> See Annex III, Part A.

(2) In each Member State, mandatory provisions determine the technical characteristics of measuring instruments and the methods of metrological control. Those requirements differ from one Member State to another. Those differences hinder trade and may create unequal conditions of competition within the Community.

(3) One of the objectives of controls in each Member State is to give assurance to customers that quantities delivered correspond to the price paid. Consequently, the aim of this Directive should not be to abolish those controls but to eliminate differences between rules in so far as these constitute a hindrance to trade.

(4) Those hindrances to the functioning of the internal market can be reduced and eliminated if the same requirements apply in Member States, initially complementing national provisions in force and later, when the necessary conditions exist, replacing those provisions.

(5) Even during the period when they coexist with national provisions, the Community requirements will enable firms to manufacture products which have uniform technical characteristics and can therefore be marketed and used throughout the Community after they have undergone EC controls.

(6) Community technical requirements for design and functioning should ensure that instruments continuously give measurements that are sufficiently accurate for their intended purpose.

(7) Compliance with technical requirements is usually confirmed by Member States before measuring instruments are placed on the market or used for the first time, and where appropriate when they are in service, such confirmation being effected in particular by means of pattern approval and verification procedures. In order to achieve free movement of such instruments within the Community, it is also necessary to provide for mutual recognition of controls among Member States and to establish appropriate EC pattern approval and initial verification procedures for this purpose as well as EC methods of metrological control in accordance with this Directive and with the relevant separate Directives.

(8) The presence, on a measuring instrument or a product, of signs or marks showing that it has undergone the appropriate controls indicates that such instrument or product satisfies the relevant technical requirements of the Community, and therefore that when the instrument or product is imported or put into operation it is unnecessary to repeat the controls which have already been carried out.

(9) National metrological rules cover numerous categories of measuring instruments and products. This Directive lays down the general provisions dealing, in particular, with EC pattern approval and initial verification procedures, as well as EC methods of metrological control. Implementing Directives covering the various categories of instruments and products will lay down the technical requirements as to design, functioning and accuracy, the control procedures and, where appropriate, the conditions under which Community technical requirements are to replace the national provisions in force.

(10) The measures necessary for the implementation of this Directive should be adopted in accordance with Council Decision 1999/468/EC of 28 June 1999 laying down the procedures for the exercise of implementing powers conferred on the Commission <*>.

---

<*> OJ L 184, 17.7.1999, p. 23.

(11) In particular, the Commission should be empowered to amend Annexes I and II to this Directive and the annexes to the separate Directives. Since those measures are of general scope and are designed to amend non-essential elements of this Directive and the separate Directives, they must be adopted in accordance with the regulatory procedure with scrutiny provided for in Article 5a of Decision 1999/468/EC.

(12) The new elements introduced into this Directive only concern the committee procedures. They therefore do not need to be transposed by the Member States.

(13) This Directive should be without prejudice to the obligations of the Member States relating to the time limits for transposition into national law of the Directives set out in Annex III, Part B,

Have adopted this Directive:

1. This Directive shall apply to:

(a) instruments as defined in paragraph 2;

(b) units of measurement, the harmonisation of methods of measurement and metrological control and, where appropriate, the means required for application of such methods;

(c) the prescription, methods of measurement, metrological control and marking of quantities of pre-packaged products.

2. For the purpose of this Directive, «instruments» shall mean measuring instruments, components of measuring instruments, additional devices and measurement equipment.

3. No Member State may, on the basis of this Directive and the separate Directives relating to it, prevent, prohibit, or restrict the placing on the market and/or entry into service of an instrument or of a product described in paragraph 1 if that instrument or product bears EC marks and/or signs in accordance with the conditions laid down in this Directive and in the separate Directives relating to the instrument or product in question.

4. Member States shall attach the same value to EC pattern approval and initial verification as to the corresponding national measures.

5. The separate Directives concerning the matters referred to in paragraph 1 shall specify:

• in particular, the measurement procedures and characteristics of, and the technical requirements for, their design and functioning, as regards the instruments referred to in paragraph 1(a),
• the requirements concerning points (b) and (c) of paragraph 1.

6. The separate Directives may fix the date on which the existing national provisions are to be replaced by Community provisions.

1. Member States shall grant EC pattern approval in accordance with the provisions of this Directive and of the relevant separate Directives.

2. EC pattern approval of instruments shall constitute their admission to EC initial verification and, where the latter is not required, the authorisation to place them on the market and/or to put them into service. If the separate Directive(s) applicable to a category of instruments exempt(s) that category from EC pattern approval, the instruments in that category shall be admitted directly to EC initial verification.

3. If their inspection equipment so permits, Member States shall grant EC pattern approval for every instrument which satisfies the requirements laid down in this Directive and the separate Directives relating to the instrument in question.

4. An application for EC pattern approval may be made only by the manufacturer or his representative established within the Community. For one and the same instrument, application may be made in one Member State only.

5. A Member State which has granted EC pattern approval shall take the necessary steps to ensure that it is kept informed of any modification of, or addition to, the approved pattern. It shall inform the other Member States of such alterations.

Modifications of, or additions to, an approved pattern must receive additional EC pattern approval from the Member State which granted EC pattern approval, where such changes influence or might influence measurement results or the prescribed conditions for use of the instrument.

However, in the case of a modified pattern, a new EC pattern approval shall be granted instead of an addition to the original EC pattern approval certificate if the pattern is modified after the provisions of this Directive or of the relevant separate Directive have been amended or adapted in such a way that the modified pattern could be approved only pursuant to the new provisions.

When EC pattern approval is granted for ancillary equipment, the approval shall specify:

(a) the patterns of instrument to which this equipment may be attached or in which it may be incorporated;

(b) the general conditions for the overall functioning of the instruments for which it is approved.

When an instrument has successfully completed the EC pattern approval examination laid down in this Directive and in the separate Directives relating to that instrument, the Member State which carried out that examination shall draw up an EC pattern approval certificate.

That Member State shall forward that certificate to the applicant.

In the cases provided for in Article 11 of this Directive or in a separate Directive, the applicant must, and in all other cases may, affix or cause to be affixed on each instrument conforming to the approved pattern the EC approval sign shown in the certificate.

1. EC pattern approval shall be valid for 10 years. It may be extended for successive periods of 10 years. The number of instruments which may be manufactured in accordance with the approved pattern shall not be limited.

EC pattern approvals granted on the basis of the provisions of this Directive and of a separate Directive may not be extended after the date of the entry into force of any amendment to, or adaptation of, those Community provisions, in cases where such EC pattern approvals could not have been granted on the basis of the new provisions.

When EC pattern approval is not extended, that approval shall nevertheless continue to apply to instruments already in service.

2. Where use is made of new techniques not provided for in a separate Directive, EC pattern approval with limited effect may be granted, after prior consultation of the other Member States.

It may include the following restrictions:

(a) a limit on the number of instruments which may be covered by the approval;

(b) an obligation to notify the competent authorities of the places of installation;

(c) restrictions on use;

(d) special restrictions concerning the technique used.

However, it may not be granted unless:

(a) the separate Directive for that category of instruments has come into force;

(b) no derogation has been made from the maximum permissible errors laid down in the separate Directives.

The period of validity of such approval shall not exceed two years. It may be extended by up to three years.

3. The Member State which has granted the limited EC pattern approval referred to in paragraph 2 shall apply for adjustment to technical progress of Annexes I and II to this Directive, where appropriate, and of the separate Directives, in accordance with the procedure referred to in Article 17(2), as soon as it considers that a new technique has proved to be satisfactory.

When EC pattern approval is not required for a category of instruments which meets the requirements of a separate Directive, the manufacturer may, on his own responsibility, affix to the instruments in this category the special sign described in point 3.3 of Annex I.

1. The Member State which has granted EC pattern approval may withdraw it:

(a) if instruments for which this approval was granted do not conform to the approved pattern or to the provisions of the relevant separate Directive;

(b) if the metrological requirements specified in the certificate of approval or the provisions of Article 5(2) are not met;

(c) if it ascertains that approval was granted in an improper manner.

2. The Member State which has granted EC pattern approval must withdraw it if the instruments constructed according to an approved pattern reveal in service a defect of a general nature which makes them unsuitable for their intended use.

3. If the Member State which granted an EC pattern approval is informed by another Member State of the occurrence of one of the cases covered by paragraphs 1 and 2, it shall also take the measures provided for in those paragraphs, after consulting with that other Member State.

4. The Member State which declares that the case referred to in paragraph 2 has arisen may forbid the placing on the market and putting into service of the instruments concerned until further notice.

It shall immediately inform the other Member States and the Commission, stating the reasons on which its decision is based.

The same procedure shall apply in the cases referred to in paragraph 1, with respect to instruments which have been exempted from EC initial verification, if the manufacturer, after due warning, does not bring the instruments into conformity with the approved pattern or with the requirements of the relevant separate Directive.

5. If the Member State which granted the EC pattern approval disputes that the case referred to in paragraph 2 of which it has been informed has arisen, or disputes that the measures taken pursuant to paragraph 4 are justified, the Member States concerned shall endeavour to settle the dispute.

The Commission shall be kept informed. It shall, where necessary, hold appropriate consultations with the aim of reaching a settlement.

1. EC initial verification constitutes the examination of a new or reconditioned instrument and the confirmation of its conformity to the approved pattern and/or to the requirements of this Directive and the separate Directives relating to the instrument in question. It is certified by the EC initial verification mark.

2. EC initial verification of instruments may be carried out by a method other than unit checking in the cases specified in the separate Directives and in accordance with the procedures adopted.

3. If their equipment so permits, Member States shall carry out EC initial verification of instruments submitted as having the measurement characteristics and satisfying the technical construction and functioning requirements laid down by the separate Directives relating to that category of instruments.

4. In the case of instruments bearing the EC initial verification mark, the obligation imposed on Member States under Article 1 (3) shall last until the end of the year following that in which the EC initial verification mark was affixed, unless separate Directives provide for a longer period.

1. When an instrument is submitted for EC initial verification, the Member State carrying out the examination shall determine:

(a) whether the instrument belongs to a category exempt from EC pattern approval and, if so, whether it satisfies the technical construction and functioning requirements laid down by the separate Directives relating to that instrument;

(b) whether the instrument has received EC pattern approval and, if so, whether it conforms to the approved pattern, and to the separate Directives relating to that instrument, in force on the date of issue of that EC pattern approval.

2. The examination carried out in EC initial verification relates in particular, in accordance with the separate Directives, to:

(a) the metrological characteristics;

(b) the maximum permissible errors;

(c) the construction, in so far as this guarantees that the measurement characteristics are not likely to deteriorate to any great extent under normal conditions of use;

(d) the presence of prescribed inscriptions and stamp plates or provisions for EC initial verification marking.

When an instrument has successfully undergone EC initial verification, in accordance with the requirements of this Directive and of the separate Directives, the EC partial or final verification marks described in Annex II, point 3 shall be affixed to that instrument under the responsibility of the Member State concerned in accordance with the rules laid down in that point.

When EC initial verification is not required for a category of instruments which meet the requirements of a separate Directive, the manufacturer shall, on his own responsibility, affix to the instruments in that category the special symbol described in point 3.4 of Annex I.

Member States shall take all necessary measures to prevent the use on instruments of marks or inscriptions liable to be confused with the EC signs or marks.

Each Member State shall notify the other Member States and the Commission of the services, agencies and institutes which are duly authorised to carry out the examinations provided for in this Directive and in the separate Directives, to issue the EC pattern approval certificates and to affix the EC initial verification marks.

Member States may require that the prescribed inscriptions be drawn up in their official language or languages.

The separate Directives shall specify the control requirements for instruments in service which bear EC signs or marks and in particular the maximum errors permitted in service. If national provisions in respect of instruments which do not bear EC signs or marks lay down less stringent requirements, the latter may serve as criteria for the controls.

The amendments necessary for adjusting to technical progress Annexes I and II to this Directive and the annexes to the separate Directives referred to in Article 1 shall be adopted by the Commission. Those measures, designed to amend non-essential elements of this Directive and the separate Directives, shall be adopted in accordance with the regulatory procedure with scrutiny referred to in Article 17(2).

However, this procedure shall apply neither to the chapter relating to imperial units of measurement of the annex to the Directive on units of measurement nor to the annexes, concerning quantity ranges for pre-packed quantities of products, to the Directives on pre-packed products.

1. The Commission shall be assisted by the Committee for Adjustment to Technical Progress of the Directives referred to in Article 16.

2. Where reference is made to this paragraph, Article 5a(1) to (4) and Article 7 of Decision 1999/468/EC shall apply, having regard to the provisions of Article 8 thereof.

All decisions taken pursuant to the provisions adopted in implementation of this Directive and of the separate Directives on the instruments in question and refusing to grant or extend EC pattern approval, withdrawing such approval, refusing to carry out EC initial verification or prohibiting placing on the market or entry into service shall state the reasons on which they are based. Such refusal, withdrawal or prohibition shall be notified to the party concerned, who shall at the same time be informed of the remedies available to him under the laws in force in the Member States and of the time limits allowed for the exercise of such remedies.

Member States shall communicate to the Commission the text of the main provisions of national law which they adopt in the field covered by this Directive.

Directive 71/316/EEC, as amended by the acts listed in Annex III, Part A, is repealed, without prejudice to the obligations of the Member States relating to the time limits for transposition into national law of the Directives set out in Annex III, Part B.

References to the repealed Directive shall be construed as references to this Directive and shall be read in accordance with the correlation table in Annex IV.

This Directive shall enter into force on the 20th day following its publication in the Official Journal of the European Union.

This Directive is addressed to the Member States.

Done at Strasbourg, 23 April 2009.

1.1. The application and the correspondence relating to it shall be drawn up in an official language in accordance with the laws of the Member State to which the application is made. The Member State has the right to require that the annexed documents should also be written in the same official language.

The applicant shall send simultaneously to all Member States a copy of his application.

(a) the name and address of the manufacturer or the firm, or of his or its authorised representative or of the applicant;

(b) the category of instrument;

(c) the intended use;

(d) the measurement characteristics;

(e) the commercial designation, if any, or the type.

1.3. The application shall be accompanied by the documents necessary for its evaluation, in duplicate, and in particular:

1.3.1. a description in particular of:

(a) the construction and operation of the instrument;

(b) the protecting arrangements ensuring correct working;

(c) the devices for regulation and adjustment;

(d) the intended locations for:

• verification marks,
• seals (where applicable);

1.3.2. general arrangement drawings and, where necessary, detailed drawings of important components;

1.3.3. a schematic drawing illustrating the principles of operation and, where necessary, a photograph.

1.4. The application shall be accompanied, where appropriate, by documents relevant to the national approvals already granted.

2.1.1. a study of the documents and an examination of the measurement characteristics of the pattern in the laboratories of the metrological service, in approved laboratories or at the place of manufacture, delivery or installation;

2.1.2. if the measurement characteristics of the pattern are known in detail, only an examination of the documents submitted.

2.2. The examination shall cover the entire performance of the instrument under normal conditions of use. Under such conditions, that instrument must maintain the measurement characteristics required.

2.3. The nature and scope of the examination mentioned in point 2.1 may be specified by separate Directives.

2.4. The metrological service may require the applicant to put at its disposal the standards and the appropriate means in terms of material and assisting personnel for the performance of the approval tests.

3.1. The certificate shall give the results of the examination of the pattern and shall specify the other requirements which must be complied with. It shall be accompanied by descriptions, drawings and diagrams necessary to identify the pattern and to explain its functioning. The sign of approval provided for in Article 4 shall be a stylised letter epsilon containing:

• in the upper part, the distinguishing capital letter(s) of the Member State which granted the approval (B for Belgium, BG for Bulgaria, CZ for the Czech Republic, DK for Denmark, D for Germany, EST for Estonia, IRL for Ireland, EL for Greece, E for Spain, F for France, I for Italy, CY for Cyprus, LV for Latvia, LT for Lithuania, L for Luxembourg, H for Hungary, M for Malta, NL for Netherlands, A for Austria, PL for Poland, P for Portugal, RO for Romania, SI for Slovenia, SK for Slovakia, FI for Finland, S for Sweden, UK for the United Kingdom) and the last two digits of the year of approval,
• in the lower part, a designation to be determined by the metrological service which granted approval (an identification number).

An example of this approval sign is shown in point 6.1.

3.2. In the case of EC limited approval, the letter P, having the same dimensions as the stylised letter epsilon, shall be placed before this letter.

An example of this limited approval sign is shown in point 6.2.

3.3. The sign mentioned in Article 6 is the same as the EC approval sign, except that the stylised letter epsilon is reversed symmetrically about a vertical axis and bears no other indication unless the separate Directives stipulate otherwise.

An example of this sign is shown in point 6.3.

3.4. The sign mentioned in Article 11 is the same as the EC approval sign in a hexagon.

An example of this sign is shown in point 6.4.

3.5. The signs mentioned in points 3.1 to 3.4 and affixed by the manufacturer in accordance with the provisions of this Directive must be affixed at a visible point of each instrument and all ancillary equipment submitted for verification, and must be legible and indelible. If their affixation presents technical difficulties, exceptions may be made in separate Directives or accepted after agreement among the metrological services of Member States has been reached.

In the cases mentioned by separate Directives, the service which granted the approval may, if it considers this necessary, request the deposition of the sample instrument for which approval has been granted. Instead of that sample instrument, the service may authorise the depositing of parts of the instrument, of scale models or of drawings, and will mention this on the EC certificate of approval.

5.1. At the same time as the party concerned is notified, copies of the EC certificate of approval shall be sent to the Commission and to the other Member States; the latter can also obtain copies of the reports of the metrological examinations if they wish.

5.2. Withdrawal of EC pattern approval and other communications concerning the extent and validity of EC pattern approval shall also be subject to the announcement procedure mentioned in point 5.1.

5.3. A Member State which refuses to grant EC pattern approval shall inform the other Member States and the Commission of its decision.

Example: <*> EC pattern approval granted by the Metrological Service of Germany in 1971 (see point 3.1, first indent).

---

<*> Рисунок не приводится.

Identification number of the EC pattern approval (see point 3.1, second indent).

Example: <*> EC limited pattern approval granted by the Metrological Service of Germany in 1971.

---

<*> Рисунок не приводится.

Identification number of the EC limited pattern approval.

Example: <*>

---

<*> Рисунок не приводится.

6.4. Sign of EC pattern approval for instruments exempt from EC initial verification (see point 3.4)

Example: <*> EC pattern approval granted by the Metrological Service of Germany in 1971.

---

<*> Рисунок не приводится.

Identification number of the EC pattern approval.

1.1. The EC initial verification may be carried out in one or more stages (usually two).

1.2.1. the EC initial verification shall be carried out in one stage on instruments which constitute a whole on leaving the factory, that is to say instruments which, theoretically, can be transferred to their place of installation without first having to be dismantled;

1.2.2. the EC initial verification shall be carried out in two or more stages for instruments the correct functioning of which depends on the conditions in which they are installed or used;

1.2.3. the first stage of the verification procedure must ensure, in particular, that the instrument conforms to the approved EC pattern or, in the case of instruments exempt from pattern approval, that they conform to the relevant provisions.

2.1. If the separate Directives do not specify the place where verification is to be carried out, instruments which have to be verified in only one stage shall be verified at the place chosen by the metrological service concerned.

2.2. Instruments which have to be verified in two or more stages shall be verified by the metrological service territorially competent.

2.2.1. The last stage of verification must be carried out at the place of installation.

2.2.2. The other stages of verification shall be carried out as laid down in point 2.1.

2.3. In particular, when the verification takes place outside the office of verification the metrological service carrying out the verification may require the applicant:

• to put at its disposal the standards and the appropriate means in terms of material and assisting personnel for the performance of the verification,
• to provide a copy of the EC certificate of approval.

3.1.1. Subject to the provisions of separate Directives, EC initial verification marks which are affixed in accordance with point 3.3 shall be as follows:

3.1.1.1. the final EC verification mark shall be composed of two stamps:

(a) the first consists of a lower-case letter «e» containing:

• in the upper half, the distinguishing capital letter(s) of the Member State where the original check is carried out (B for Belgium, BG for Bulgaria, CZ for the Czech Republic, DK for Denmark, D for Germany, EST for Estonia, IRL for Ireland, EL for Greece, E for Spain, F for France, I for Italy, CY for Cyprus, LV for Latvia, LT for Lithuania, L for Luxembourg, H for Hungary, M for Malta, NL for Netherlands, A for Austria, PL for Poland, P for Portugal, RO for Romania, SI for Slovenia, SK for Slovakia, FI for Finland, S for Sweden, UK for the United Kingdom) together, where necessary, with one or two figures identifying a territorial or administrative subdivision,
• in the lower half, the identification number of the verifying agent or office;

(b) the second stamp shall consist of the last two digits of the year of the verification, in a hexagon;

3.1.1.2. the mark of EC partial verification shall consist solely of the first stamp. It shall also serve as a seal.

3.2.1. The attached drawings <*> show the shape, dimensions and outline of the letters and numbers for the EC initial verification marks as laid down in point 3.1; the first two drawings show the various parts of the stamp and the third is an example of a stamp. The dimensions given in the drawings are relative values; they are a function of the diameter of the circle described about the lower-case letter «e» and about the field of the hexagon.

---

<*> Рисунки не приводятся.

The actual diameters of the circles described about the marks are 1,6 mm, 3,2 mm, 6,3 mm, 12,5 mm.

3.2.2. The metrological services of Member States shall mutually exchange the original drawings of the EC initial verification marks, conforming to the models in the annexed drawings.

3.3.1. The final EC verification mark shall be affixed at the appointed location on the instrument when the latter has been completely verified and is recognised to conform to EC requirements.

3.3.2 The partial EC verification mark shall be affixed:

3.3.2.1. when verification is made in several stages, on the instrument or part of an instrument which fulfils the conditions laid down for operations other than those at the place of installation, at the place where the stamp-date is affixed or in any other place specified in the separate Directives;

3.3.2.2. in all cases as a seal, in the places specified in the separate Directives.

(referred to in Article 20)

Council Directive 71/316/EEC (OJ L 202, 6.9.1971, p. 1). 1972 Act of Accession, Annex I, point X.12 (OJ L 73, 27.3.1972, p. 118). Council Directive 72/427/EEC (OJ L 291, 28.12.1972, p. 156). 1979 Act of Accession, Annex I, point X.A (OJ L 291, 19.11.1979, p. 108). Council Directive 83/575/EEC (OJ L 332, 28.11.1983, p. 43). 1985 Act of Accession, Annex I, point IX.A.7 (OJ L 302, 15.11.1985, p. 212).

Council Directive 87/354/EEC             Only as regards references made to
(OJ L 192, 11.7.1987, p. 43).            Directive 71/316/EEC in Article 1

                                     and Annex, point 4

Council Directive 87/355/EEC (OJ L 192, 11.7.1987, p. 46). Council Directive 88/665/EEC Only Article 1(1) (OJ L 382, 31.12.1988, p. 42). 1994 Act of Accession, Annex I, point XI.C.VII.1 (OJ C 241, 29.8.1994, p. 211). Council Regulation (EC) No 807/2003 Only Annex III, point 5 (OJ L 122, 16.5.2003, p. 36). 2003 Act of Accession, Annex II, point I.D.1 (OJ L 236, 23.9.2003, p. 64).

Council Directive 2006/96/EC             Only as regards references made to
(OJ L 363, 20.12.2006, p. 81).           Directive 71/316/EEC in Article 1

                                     and Annex, point B.1

Commission Directive 2007/13/EC (OJ L 73, 13.3.2007, p. 10).

(referred to in Article 20)

Directive	Time limit for transposition
71/316/EEC	30 January 1973
83/575/EEC	1 January 1985
87/354/EEC	31 December 1987
87/355/EEC	31 December 1987
2006/96/EC	1 January 2007
2007/13/EC	9 March 2008

CORRELATION TABLE

Directive 71/316/EEC	This Directive
Article 1(1)(a)	Article 1(1), point (a) and Article 1(2)
Article 1(1)(b)	Article 1(1), point (b)
Article 1(1)(c)	Article 1(1), point (c)
Article 1(2)	Article 1(3)
Article 1(3)	Article 1(4)
Article 1(4), first subparagraph	Article 1(5)
Article 1(4), second subparagraph	Article 1(6)
Article 2(1)	Article 2(2)
Article 2(2)	Article 2(3)
Article 2(3)	Article 2(4)
Article 2(4)	Article 2(5)
Article 2(5)	Article 2(1)
Article 3, introductory wording	Article 3, introductory wording
Article 3, first indent	Article 3, point (a)
Article 3, second indent	Article 3, point (b)
Article 4, first sentence	Article 4, first and second paragraphs
Article 4, second sentence	Article 4, third paragraph
Article 5(1)	Article 5(1)
Article 5(2), first subparagraph	Article 5(2) first subparagraph
Article 5(2), second subparagraph, introductory wording	Article 5(2) second subparagraph, introductory wording
Article 5(2), second subparagraph, first indent	Article 5(2) second subparagraph, point (a)
Article 5(2), second subparagraph second indent	Article 5(2) second subparagraph, point (b)
Article 5(2), second subparagraph, third indent	Article 5(2) second subparagraph, point (c)
Article 5(2), second subparagraph, fourth indent	Article 5(2) second subparagraph, point (d)
Article 5(2), third subparagraph, introductory wording	Article 5(2) third subparagraph, introductory wording
Article 5(2), third subparagraph, first indent	Article 5(2) third subparagraph, point (a)
Article 5(2), third subparagraph, second indent	Article 5(2) third subparagraph, point (b)
Article 5(2), fourth subparagraph	Article 5(2) fourth subparagraph
Article 5(3)	Article 5(3)
Article 6	Article 6
Article 7(1), (2) and (3)	Article 7(1), (2) and (3)
Article 7(4), first sentence	Article 7(4), first subparagraph
Article 7(4), second sentence	Article 7(4), second subparagraph
Article 7(4), third sentence	Article 7(4), third subparagraph
Article 7(5)	Article 7(5)
Article 8(1), point (a)	Article 8(1)
Article 8(1), point (b)	Article 8(2)
Article 8(2)	Article 8(3)
Article 8(3)	Article 8(4)
Article 9(1)	Article 9(1)
Article 9(2), introductory wording	Article 9(2), introductory wording
Article 9(2), first indent	Article 9(2), point (a)
Article 9(2), second indent	Article 9(2), point (b)
Article 9(2), third indent	Article 9(2), point (c)
Article 9(2), fourth indent	Article 9(2), point (d)
Articles 10 and 11	Articles 10 and 11
Articles 12, 13 and 14	Articles 12, 13 and 14
Article 15	Article 15
Article 16, first sentence	Article 16, first paragraph
Article 16, second sentence	Article 16, second paragraph
Article 17	-
Article 18(1)	Article 17(1)
Article 18(2), first subparagraph	Article 17(2)
Article 18(2), second subparagraph	-
Article 18(3)	-
Article 19	Article 18
Article 20(1)	-
Article 20(2) -	Article 19 Articles 20 and 21
Article 21	Article 22
Annex I	Annex I
Points 1 and 1.1	Points 1 and 1.1
Point 1.2, introductory wording	Point 1.2, introductory wording
Point 1.2, first indent	Point 1.2(a)
Point 1.2, second indent	Point 1.2(b)
Point 1.2, third indent	Point 1.2(c)
Point 1.2, fourth indent	Point 1.2(d)
Point 1.2, fifth indent	Point 1.2(e)
Point 1.3	Point 1.3
Point 1.3.1, introductory wording	Point 1.3.1, introductory wording
Point 1.3.1, first indent	Point 1.3.1(a)
Point 1.3.1, second indent	Point 1.3.1(b)
Point 1.3.1, third indent	Point 1.3.1(c)
Point 1.3.1, fourth indent	Point 1.3.1(d)
Point 1.3.2 to Point 5	Point 1.3.2 to Point 5
Point 5.2	Point 5.1
Point 5.3	Point 5.2
Point 5.4	Point 5.3
Point 6 to Point 6.4	Point 6 to Point 6.4
Annex II — -	Annex II Annex III Annex IV

---