---
title: "Постановление Минтруда РФ от 23.03.1994 N 26"
number: "26"
issuer: "Министерство труда и социального развития Российской Федерации"
issued_on: 1994-03-23
status: действует
canonical: "https://bukva.ai/docs/postanovlenie-26-1994"
---

## Постановление Минтруда РФ от 23.03.1994 N 26

# Постановление Минтруда РФ от 23.03.1994 N 26

"Об утверждении Укрупненных нормативов времени на работы, выполняемые на фрезерных, строгальных и долбежных станках в условиях ремонтных цехов и мастерских"

> [!IMPORTANT]
> КонсультантПлюс: примечание.
> Данный документ носит рекомендательный характер и может быть использован в качестве основы для разработки систем нормирования труда, устанавливаемых в организациях.
> В соответствии с Трудовым [кодексом](https://bukva.ai/docs/kodeks-197-fz/statya-159#p734) РФ системы нормирования труда определяются работодателем с учетом мнения представительного органа работников или устанавливаются коллективным договором. Для однородных работ могут разрабатываться и устанавливаться типовые (межотраслевые, отраслевые, профессиональные и иные) нормы труда в соответствии с [Правилами](https://bukva.ai/docs/postanovlenie-804-2002#p100008), утвержденными Постановлением Правительства РФ от 11.11.2002 N 804.


<a id="p100001"></a>**МИНИСТЕРСТВО ТРУДА РОССИЙСКОЙ ФЕДЕРАЦИИ**


## <a id="p100002"></a>ПОСТАНОВЛЕНИЕ

от 23 марта 1994 г. N 26

<a id="p100003"></a>**ОБ УТВЕРЖДЕНИИ УКРУПНЕННЫХ НОРМАТИВОВ**
**ВРЕМЕНИ НА РАБОТЫ, ВЫПОЛНЯЕМЫЕ НА ФРЕЗЕРНЫХ, СТРОГАЛЬНЫХ**
**И ДОЛБЕЖНЫХ СТАНКАХ В УСЛОВИЯХ РЕМОНТНЫХ**
**ЦЕХОВ И МАСТЕРСКИХ**

<a id="p100004"></a>Министерство труда Российской Федерации постановляет:
1. <a id="p100005"></a>Утвердить Укрупненные [нормативы времени](#p100012) на работы, выполняемые на фрезерных, строгальных и долбежных станках в условиях ремонтных цехов и мастерских, разработанные Центральным бюро нормативов по труду при Всероссийском центре производительности Минтруда России.
2. <a id="p100006"></a>Установить, что Укрупненные [нормативы времени](#p100012), утвержденные настоящим Постановлением, рекомендуются для применения в ремонтных цехах и мастерских на промышленных предприятиях и в организациях независимо от ведомственной подчиненности, форм собственности и хозяйствования.
3. <a id="p100007"></a>Рекомендовать министерствам, ведомствам, предприятиям и организациям в трехмесячный срок с учетом потребности представить заявки Центральному бюро нормативов по труду на издание Укрупненных [нормативов времени](#p100012), утвержденных настоящим Постановлением.
4. <a id="p100008"></a>Центральному бюро нормативов по труду обеспечить издание необходимого количества указанных Укрупненных [нормативов времени](#p100012).

<div align="right">

<a id="p100009"></a>Заместитель Министра труда<br>
Российской Федерации

</div>

**Р.БАТКАЕВ**





<div align="right">

<a id="p100011"></a>Утверждены<br>
Постановлением Министерства труда<br>
Российской Федерации

</div>

от 23 марта 1994 г. N 26


## <a id="p100012"></a>УКРУПНЕННЫЕ НОРМАТИВЫ ВРЕМЕНИ НА РАБОТЫ, ВЫПОЛНЯЕМЫЕ НА ФРЕЗЕРНЫХ, СТРОГАЛЬНЫХ И ДОЛБЕЖНЫХ СТАНКАХ В УСЛОВИЯХ РЕМОНТНЫХ ЦЕХОВ И МАСТЕРСКИХ


<a id="p100013"></a>Укрупненные нормативы времени утверждены Постановлением Министерства труда Российской Федерации N 26 от 23.03.94 и рекомендованы для применения в ремонтных цехах и мастерских на машиностроительных и немашиностроительных предприятиях независимо от ведомственной подчиненности, форм собственности и хозяйствования.
<a id="p100014"></a>[Нормативы](https://bukva.ai/docs/kodeks-197-fz/statya-161#p1567) времени разработаны Центральным бюро нормативов по труду при участии нормативно-исследовательских организаций и предприятий машиностроительных и немашиностроительных министерств и ведомств.
<a id="p100015"></a>Сборник содержит нормативы подготовительно-заключительного времени, вспомогательного времени на установку и снятие детали, неполного штучного времени на обработку плоскостей, уступов, пазов на фрезерных, строгальных и долбежных станках.
<a id="p100016"></a>Нормативы времени предназначены на нормировщиков и технологов, а также инженерно-технических работников, занятых разработкой технически обоснованных норм времени на станочные работы в ремонтных цехах и мастерских в условиях единичного производства.


### 1. <a id="p100017"></a>Общая часть


<a id="p100018"></a>1.1. Укрупненные нормативы времени из работы, выполняемые на фрезерных, строгальных и долбежных станках, предназначены для расчета норм времени и выработки, выдачи нормированных заданий, составления плана и текущего задания, расчета численности рабочих-станочников и определения количества обслуживаемых рабочим станков и рекомендуются для применения в ремонтно-механических цехах и мастерских с единичным типом производства.
<a id="p100019"></a>Применение нормативов не потребует дополнительного изменения времени для каждого нового задания. Нормативы, приведенные в сборнике по видам обработки, позволят определить норму штучного времени на деталь.

#### <a id="p100020"></a>1.2 В основу разработки укрупненных нормативов положены:

<a id="p100021"></a>материалы производственных наблюдений за режимами резания и затратами времени на операцию, результаты анализа трудовых процессов, изучения рациональных методов труда и организации рабочего места на металлорежущих станках;
<a id="p100022"></a>Общемашиностроительные [нормативы](https://bukva.ai/docs/obschemashinostroitelnye-normativy-vremeni-goskomtrud-sssr) времени вспомогательного на обслуживание рабочего места и подготовительно-заключительного при работе на металлорежущих станках (мелкосерийное и единичное производство);
<a id="p100023"></a>Общемашиностроительные укрупненные нормативы времени на работы, выполняемые на металлорежущих станках. Единичное, мелкосерийное и среднесерийное производство;
<a id="p100024"></a>Часть II. Фрезерные станки;
<a id="p100025"></a>Часть IV. Строгальные и долбежные станки;
<a id="p100026"></a>Отраслевые укрупненные нормативы и нормы времени на работы, выполняемые на металлорежущих станках;
<a id="p100027"></a>техническая литература по теме и паспортные данные металлорежущих станков.
<a id="p100028"></a>1.3. Сборник содержит нормативы подготовительно-заключительного времени, времени на установку и снятие детали, укрупненные нормативы при обработке плоскостей, уступов, пазов, выраженные в минутах, на поперечно-строгальных, продольно-строгальных, долбежных, горизонтально-вертикально-фрезерных и продольно-фрезерных станках.
<a id="p100029"></a>1.4. Режимы резания, припуски на механическую обработку, теоретическая масса заготовки, механические свойства основных конструкционных углеродистых и легированных сталей, чугуна и медных сплавов в качестве справочных материалов приводятся в [Приложениях 1](#p101716) - [7](#p102023).
<a id="p100030"></a>1.5. Укрупненные нормативы времени установлены на принятый измеритель (на обработку плоскостей, пазов и уступов) и выражены в мин.
<a id="p100031"></a>Нормативы времени на обработку крупногабаритных деталей рассчитываются по общемашиностроительным нормативам времени и режимов резания для тяжелых станков.
<a id="p100032"></a>1.6. Нормирование станочных работ в механических цехах основного производства данными нормативами не предусматривается ввиду различных условий организации производства и технологии обработки.
<a id="p100033"></a>1.7. Нормативы времени рассчитаны на организационно-технические условия, соответствующие единичному типу производства.
<a id="p100034"></a>В случаях изменения партионности к нормативам времени следует применять поправочные коэффициенты, приведенные в [карте 1](#p100218).
<a id="p100035"></a>Принятый в нормативах уровень производительности труда учитывает опыт работы ремонтных цехов и мастерских предприятий различных отраслей промышленности.
<a id="p100036"></a>В тех случаях, когда время на обработку по действующим на предприятии местным нормативам меньше норм времени, рассчитанных по данным нормативам, увеличивать эти, более прогрессивные нормативы времени, не следует.
<a id="p100037"></a>1.8. Нормативы времени рассчитаны для выполнения работ при одностаночном обслуживании. При многостаночном обслуживании нормы времени, рассчитанные по данным нормативам, следует применять с коэффициентами, приведенными в [карте 1](#p100218).
<a id="p100038"></a>1.8.1. Нормативы времени могут быть использованы при расчете комплексных норм времени при внедрении коллективной формы организации труда.
<a id="p100039"></a>1.9. Тарификация работ должна проводиться по Единому тарифно-квалификационному справочнику работ и профессий рабочих, выпуск 2, утвержденному Постановлением Государственного комитета СССР по труду и социальным вопросам и ВЦСПС от 16.01.85 N 17/2-54, применяемому на территории Российской Федерации в соответствии с Постановлением Министерства труда России от 9 июня 1992 г. N 20.
<a id="p100040"></a>Несоответствие квалификации рабочего установленному разряду работы не может служить основанием для каких-либо изменений норм времени, рассчитанных по сборнику.

#### <a id="p100041"></a>1.10 Норма времени и ее составляющие.

<a id="p100042"></a>    Норма   времени   на  работы,  выполняемые  на  металлорежущих
станках,     состоит      из      штучного      времени     Т    и
                                                             ш
подготовительно-заключительного  времени  t    и   определяется по
                                           пз
формуле:

                                t
                                 пз
<a id="p100043"></a>                Н   = Т  x (1 + --- ), мин.,                 (1.1)
                 вр    ш        100

<a id="p100044"></a>    где:
    Н   - норма времени, мин.
     вр
<a id="p100045"></a>1.11. Норма штучного времени по настоящим нормативам определяется путем суммирования времени на установку и снятие детали и неполного штучного времени на обработку поверхностей с учетом числа рабочих ходов:

<a id="p100046"></a> T  = [t  + (t   x i + t    x i  +...+ t    x i )] x К   x К   x К   , мин.,  (1.2)
  ш     ву    нш    1   нш     2        нш     n      Т     ос    орм
                1         2               n            ш

<a id="p100047"></a>    где:
    t   - вспомогательное время  на  установку  и  снятие  детали,
     ву
мин.;
    t   ; t   ;...t    - неполное  штучное  время   на   обработку
     нш    нш      нш
       1     2       n
поверхности, мин.;
    i - число рабочих ходов;
    К   - поправочный коэффициент  на  норму  штучного  времени  в
     Т
      ш
зависимости от числа деталей в партии;
    К   - поправочный коэффициент  на  норму  штучного  времени  в
     ос
зависимости от числа обслуживаемых станков;
    К    - поправочный коэффициент на  норму  штучного  времени  в
     орм
зависимости от организации рабочих мест.

##### <a id="p100048"></a>1.10.2 Нормативы подготовительно-заключительного времени предусматривают выполнение следующей работы:

- <a id="p100049"></a>получение наряда и технической документации;
- <a id="p100050"></a>ознакомление с работой, чертежами и получение инструктажа от мастера;
- <a id="p100051"></a>подбор материалов и заготовок, перемещение их к рабочему месту на расстояние до 20 м;
- <a id="p100052"></a>получение инструмента и приспособлений, подготовка рабочего места, наладка оборудования, инструмента и приспособлений;
- <a id="p100053"></a>частичная переналадка оборудования в процессе выполнения работы;
- <a id="p100054"></a>снятие инструмента и приспособлений по окончании обработки партии деталей, их сдача.
<a id="p100055"></a>Приведенное в [карте 2](#p100238) подготовительно-заключительное время дифференцировано по группам оборудования в зависимости от технических характеристик (диаметра устанавливаемой заготовки, диаметра планшайбы или шпинделя и т.д.) и дано в процентах от штучного времени, рассчитанного на организацию труда, при которой рабочее место станочника обслуживается самим исполнителем.
<a id="p100056"></a>1.10.3. Нормативы вспомогательного времени на установку и снятие деталей приведены в зависимости от массы детали, способа и характера установки, выверки и состояния установочной поверхности.
<a id="p100057"></a>Время на установку и снятие детали приведено укрупненно на комплексы приемов по видам оборудования.
<a id="p100058"></a>Например, при работе со штучными заготовками в универсальном или специальном приспособлении в комплексы включены приемы: взять деталь (заготовку), установить в зажимное приспособление, выверить и закрепить, включить и выключить станок, открепить деталь, снять и отложить на место, очистить приспособление или поверхность стола от стружки (по необходимости).
<a id="p100059"></a>Кроме перечисленных основных приемов в состав комплексов включены также приемы:
- <a id="p100060"></a>(при работе краном) - вызвать кран, застропить и отстропить деталь.
<a id="p100061"></a>В целях упрощения расчетов время на установку и снятие детали включает соответствующее время на обслуживание рабочего места, перерыв на отдых и личные потребности.
<a id="p100062"></a>Нормативами предусматривается установка и снятие детали массой до 30 кг вручную и свыше 30 кг с помощью подъемных механизмов.

##### <a id="p100063"></a>1.10.4 Нормативы неполного штучного времени на обработку поверхности включают:

- <a id="p100064"></a>основное время;
- <a id="p100065"></a>вспомогательное время, связанное с обработкой поверхности в зависимости от ее размеров, вида и характера обработки, технических условий на обработку;
- <a id="p100066"></a>вспомогательное время на изменение режима работы станка и смену инструмента;
- <a id="p100067"></a>время на обслуживание рабочего места, перерывы на отдых и личные потребности (включенные в неполное штучное время) - см. таблицу 1.1.

<a id="p100068"></a>Таблица 1.1

<div align="center">

<a id="p100069"></a>**ВРЕМЯ НА ОБСЛУЖИВАНИЕ РАБОЧЕГО МЕСТА, ОТДЫХ**

</div>

**И ЛИЧНЫЕ ПОТРЕБНОСТИ**


| Наименование оборудования | Время в % от оперативного |
| --- | --- |
| Горизонтально-вертикально-фрезерные | 10,5 |
| Продольно-фрезерные | 11,5 |
| Поперечно-строгальные | 12,5 |
| Продольно-строгальные | 13,5 |
| Долбежные | 12,0 |


<a id="p100076"></a>В комплексы приемов вспомогательного времени, связанного с обработкой поверхности, включено время на контрольные измерения с учетом их периодичности, применяемого измерительного инструмента и средней продолжительности измерения.
<a id="p100077"></a>Периодичность контрольных измерений установлена в зависимости от вида обработки и типа оборудования, размеров и точности обрабатываемой поверхности, способа достижения точности заданного размера.
<a id="p100078"></a>Основное (технологическое) время определено исходя из рационального сочетания факторов режимов резания (глубины резания t, подачи S, скорости резания V и стойкости инструмента Т), при которых обеспечивается наибольшая производительность труда.
<a id="p100079"></a>Режимы резания установлены применительно к условиям обработки универсальными режущими инструментами из наиболее часто применяемых марок инструментальных материалов на распространенном в ремонтных цехах оборудовании.
<a id="p100080"></a>Основное время рассчитано по средним режимам в расчете не на конкретный станок, а на группу аналогичного по виду оборудования, так как при большой номенклатуре моделей станков в ремонтных цехах рассчитывать нормы с учетом выполнения работы на конкретном станке нецелесообразно.
<a id="p100081"></a>Неполное штучное время в картах приведено на полную обработку поверхностей, пазов с учетом заданного числа рабочих ходов при нормальных припусках и в зависимости от размеров обрабатываемой поверхности, а также технических условий на обработку.
<a id="p100082"></a>Для стальных заготовок приводится время отдельно на обработку поверхностей из проката и из поковки, причем черновой рабочий ход для поковки учитывает работу по корке.
<a id="p100083"></a>При большем числе рабочих ходов, чем предусмотрено в картах, время на дополнительные рабочие ходы принимать по черновой обработке Rz 80.
<a id="p100084"></a>При обработке уступов приведено время на один рабочий ход в зависимости от глубины.
<a id="p100085"></a>Неполное штучное время в картах нормативов рассчитано для определенных, заданных технологических условий выполнения работы.
<a id="p100086"></a>Для случаев обработки, отличных от принятых при расчете нормативов, в тех же картах, а также в [карте 1](#p100218) приводятся поправочные коэффициенты, учитывающие другие условия выполнения работ.
<a id="p100087"></a>Для продольно-строгальных станков нормативы неполного штучного времени рассчитаны на обработку поверхности одним резцом.
<a id="p100088"></a>В целях лучшего использования оборудования и повышения производительности труда следует там, где это возможно, вести обработку двумя суппортами, что сократит время обработки.

##### <a id="p100089"></a>1.10.5 Примеры расчета норм времени.

<a id="p100090"></a>*Пример* 1


<table>
<colgroup><col width="4%"><col width="23%"><col width="37%"><col width="12%"><col width="8%"><col width="17%"></colgroup>
<tr><td></td><td>Эскиз обработки</td><td>Определение элементов норм времени</td><td colspan="3">Горизонтально- и вертикальнофрезерные станки</td></tr>
<tr><td></td><td></td><td></td><td>Обозначение</td><td>Время, мин.</td><td>Обоснование</td></tr>
<tr><td rowspan="3">1.</td><td rowspan="2">рисунок не приводится Исходные данные:</td><td>Установить и снять деталь, переустановить 3 раза t = t x 4 x К = 2 x 4 x 1,2 ву ву 1</td><td>t ву К = 1,2 t ву 1</td><td>2 9,6</td><td>Карта 3, поз. 2г Примечание, <a href="#p100274">п. 1</a> расчетное</td></tr>
<tr><td>Фрезеровать поверхности 1 и 4 шероховатостью до Rz 80 t = t x 2 x K x K x К = нш нш тв N 1 = 2,9 x 2 x 1,0 x 1,0 x 1,2 = = 6,96 примерно равно 7,0</td><td>t нш К = 1,0 тв K = 1,0 N К = 1,2 t нш 1</td><td>2,9 7,0</td><td>Карта 5, поз. 1ж Примечание, <a href="#p100310">п. 2</a> расчетное</td></tr>
<tr><td>Наименование операции:</td><td>Фрезеровать поверхности 2 и 3 шероховатостью до Rz 80</td><td>t нш</td><td>5,1</td><td>Карта 5, поз. 3з</td></tr>
<tr><td>2.</td><td>Фрезерная Содержание работы: фрезеровать 4-е поверхности в размер 45 x 90 на длине 500 и 530 мм</td><td>t = t x 2 x K x K x К = нш нш тв N 2 = 5,1 x 2 x 1,0 x 1,0 x 1,2 = = 12,24</td><td>К = 1,0 тв K = 1,0 N К = 1,2 t</td><td>12,2</td><td>- расчетное</td></tr>
<tr><td>3.</td><td>Станок - вертикально-фрезерный, модель 6Н12</td><td></td><td>нш 2</td><td></td><td></td></tr>
<tr><td>4.</td><td>Наименование детали - тяга</td><td>Штучное время на операцию t = (t + SUM t ) x К х</td><td>К = 0,7 п</td><td></td><td>Карта 1, п. 1, 2, 3</td></tr>
<tr><td>5.</td><td>Обрабатываемый материал - чугун серый, НВ = 1760... 2360 МПа</td><td>ш ву нш п 1 1...2 х К x К = (9,6 + 6,9 + ос орм</td><td>К = 0,1 ос К = 1,0 омр</td><td></td><td></td></tr>
<tr><td>6. 7.</td><td>Масса детали - 9,6 кг Заготовка - отливка</td><td>+ 12,7) x 0,7 x 1,0 x 1,0 = 20,16 примерно равно 20,2</td><td>t ш</td><td>20,2</td><td>расчетное</td></tr>
<tr><td>8.</td><td>с припуском 8 мм Режущий инструмент - фреза ВК-8</td><td>Норма времени составит: t пз</td><td>t = 8,0% пз</td><td></td><td><a href="#p100238">Карта 2</a></td></tr>
<tr><td>9.</td><td>Способ установки - в тисках</td><td>Н = t + t = t x (1 + ---) = вр ш пз ш 100</td><td></td><td></td><td></td></tr>
<tr><td>10.</td><td>Число обслуживаемых станков - 1</td><td>= 20,2 x 1,08 = 21,8</td><td>Н вр</td><td>21,8</td><td>расчетное</td></tr>
<tr><td>11.</td><td>Число деталей в партии - 30 шт.</td><td></td><td></td><td></td><td></td></tr>
</table>


<a id="p100108"></a>*Пример* 2


<table>
<colgroup><col width="5%"><col width="23%"><col width="37%"><col width="13%"><col width="8%"><col width="14%"></colgroup>
<tr><td rowspan="2"></td><td rowspan="2">Эскиз обработки</td><td rowspan="2">Определение элементов норм времени</td><td colspan="3">Продольно- и поперечнострогальные, долбежные станки</td></tr>
<tr><td>Обозначение</td><td>Время, мин.</td><td>Обоснование</td></tr>
<tr><td rowspan="3">1.</td><td rowspan="2">рисунок не приводится Исходные данные:</td><td>Установить и снять деталь t = t x К = 20 x 1,2 ву ву 1</td><td>t ву К = 1,2 t ву 1</td><td>20 24</td><td>Карта 34, поз. 6л Примечание, п. 1 расчетное</td></tr>
<tr><td>Строгать поверхности 1 и 2 шероховатостью до Rz 40 t = t x 2 x К x К x нш нш пп фи 1 х К x К = 172 x 2 x 0,9 x m х 1,0 x 1,0 x 0,83 = 257</td><td>t нш К = 0,9 пп К = 1,0 фи К = 1,0 К = 0,83 m t нш 1</td><td>172 257</td><td>Карта 43, поз. 21р расчетное</td></tr>
<tr><td>Наименование операции:</td><td>Переустановить деталь 3 раза t = t x 3 x К x К =</td><td>t ву</td><td>20</td><td>Карта 34, поз. 6л</td></tr>
<tr><td>2.</td><td>строгальная Содержание работы: строгать 4-е поверхности в размеры 300 x 100 = = 2500 мм</td><td>ву ву 2 = 20 x 3 x 1,2 x 0,8 = 57,6</td><td>К = 1,2 К = 0,8 t ву 2</td><td>57,6</td><td>Примечание, п. 1, 2 расчетное</td></tr>
<tr><td>3.</td><td>Станок - продольнострогальный, модель 7231А</td><td>Строгать поверхности 3 и 4 шероховатостью до Rz 40 t = t x 2 x К x К x</td><td>t нш К = 0,9</td><td>64</td><td>Карта 43, поз. 17р</td></tr>
<tr><td>4.</td><td>Наименование детали - пластина</td><td>нш нш пп фи 2</td><td>пп К = 1,0</td><td></td><td></td></tr>
<tr><td>5.</td><td>Обрабатываемый материал - сталь 3, сигма = в = 370...460 МПа</td><td>х К x К = 64 x 2 x 0,9 x m х 1,0 x 1,0 x 0,83 = 95,6</td><td>фи К = 1,0 К = 0,83 m t</td><td>95,6</td><td>расчетное</td></tr>
<tr><td>6. 7.</td><td>Масса детали - 400 кг Заготовка - поковка</td><td></td><td>нш 2</td><td></td><td></td></tr>
<tr><td>8.</td><td>Резец - Т5К10</td><td>Штучное время на операцию</td><td>К = 1,0</td><td></td><td>Карта 1,</td></tr>
<tr><td>9.</td><td>Способ установки - на столе с креплением болтами и планками</td><td>t = (SUM t + ш ву 1...2 + SUM t ) x К x К x</td><td>п К = 1,0 ос К = 1,0</td><td></td><td>п. 1, 2, 3</td></tr>
<tr><td rowspan="2">10.</td><td rowspan="2">Число деталей в партии - 2 шт.</td><td>нш п ос 1...2 x К = (24 + 57,6 + 257 + орм + 95,6) x 1,0 x 1,0 x 1,0 = 434</td><td>орм t ш</td><td>434</td><td>расчетное</td></tr>
<tr><td>Норма времени составит: t пз Н = t + t = t x (1 + ---) вр ш пз ш 100 Н = 434 x 1,075 = 466,5 вр</td><td>t = 7,5% пз Н вр</td><td>466,5</td><td><a href="#p100238">Карта 2</a> расчетное</td></tr>
</table>


<a id="p100125"></a>При обработке одновременно двумя резцами должен приниматься следующий порядок расчета неполного штучного времени:
1. <a id="p100126"></a>Определяют время на каждую из обрабатываемых поверхностей.
2. <a id="p100127"></a>Сравнивают неполное штучное время на обработку поверхностей.
3. <a id="p100128"></a>В норму штучного времени включают время обработки только одной поверхности с наибольшей величиной строгания. При этом неполное штучное время, установленное по нормативной карте на обработку этой поверхности, принимают с коэффициентом К = 1,2.
<a id="p100129"></a>Время обработки другой поверхности считается перекрываемым и в норму штучного времени не включается.
<a id="p100130"></a>При обработке одной поверхности двумя суппортами неполное штучное время, устанавливаемое по карте нормативов на обработку поверхности одним резцом, умножают на коэффициент 0,6.
<a id="p100131"></a>Для пояснения порядка пользования нормативами ниже приведены примеры расчета нормы времени.


### 2. <a id="p100132"></a>Характеристика применяемого оборудования и технология работы


<a id="p100133"></a>2.1. Нормативы времени рассчитаны при нормировании работ, выполняемых на универсальном оборудовании отечественного производства, широко распространенного в ремонтных цехах и мастерских.
<a id="p100134"></a>Краткие технические характеристики металлорежущих станков и их паспортные данные представлены в таблице 2.1.


#### <a id="p100135"></a>Таблица 2.1



<table>
<colgroup><col width="6%"><col width="23%"><col width="11%"><col width="20%"><col width="25%"><col width="15%"></colgroup>
<tr><td rowspan="2"></td><td rowspan="2">Наименование станка</td><td rowspan="2">Модель станка</td><td colspan="3">Основные параметры</td></tr>
<tr><td>Основные размеры</td><td>Частота вращения, об./мин.</td><td>Мощность, кВт</td></tr>
<tr><td></td><td>1</td><td>2</td><td>3</td><td>4</td><td>5</td></tr>
<tr><td></td><td></td><td></td><td>Рабочая поверхность стола, мм</td><td></td><td></td></tr>
<tr><td>1.</td><td>Горизонтальнофрезерный консольный станок</td><td>6Р81Г</td><td>250 x 1000</td><td>50 - 1600</td><td>5,5</td></tr>
<tr><td>2.</td><td>Горизонтальнофрезерный консольный станок</td><td>6Р82Г</td><td>320 x 1250</td><td>31,5 - 1600</td><td>7,5</td></tr>
<tr><td>3.</td><td>То же</td><td>6Р83Г</td><td>400 x 1600</td><td>31,5 - 1600</td><td>10,0</td></tr>
<tr><td>4.</td><td>Горизонтальнофрезерный универсальный станок</td><td>6Р81</td><td>250 x 1000</td><td>50 - 1600</td><td>5,5</td></tr>
<tr><td>5.</td><td>То же</td><td>6Р82</td><td>320 x 1250</td><td>31,5 - 1600</td><td>7,5</td></tr>
<tr><td>6.</td><td>То же</td><td>6Р83</td><td>400 x 1600</td><td>31,5 - 1600</td><td>10,0</td></tr>
<tr><td>7.</td><td>Вертикальнофрезерный консольный станок</td><td>6Р12</td><td>320 x 1250</td><td>31,5 - 1600</td><td>7,5</td></tr>
<tr><td>8.</td><td>То же</td><td>6Р13</td><td>460 x 1600</td><td>31,5 - 1600</td><td>10,0</td></tr>
<tr><td>9.</td><td>Продольнофрезерный двухстоечный станок</td><td>6Г610</td><td>1000 x 3200</td><td>16 - 1250</td><td>17,0 x 4</td></tr>
<tr><td>10.</td><td>То же</td><td>6620</td><td>2000 x 6300</td><td>20 - 1000</td><td>30,0 x 4</td></tr>
<tr><td>11.</td><td>То же</td><td>6625</td><td>2500 x 8000</td><td>20 - 1000</td><td>30,0 x 4</td></tr>
<tr><td colspan="3"></td><td></td><td>Частота хода стола, дв. ход./мин.</td><td></td></tr>
<tr><td>12.</td><td>Продольнострогальный двухстоечный станок</td><td>7210</td><td>1000 x 3000</td><td>4 - 80</td><td>100</td></tr>
<tr><td>13.</td><td>То же</td><td>7212</td><td>1250 x 4000</td><td>4 - 80</td><td>100</td></tr>
<tr><td>14.</td><td>То же</td><td>7216</td><td>1600 x 6000</td><td>4 - 80</td><td>100</td></tr>
<tr><td colspan="3"></td><td>Наибольший ход ползуна, мм</td><td>Частота движения ползуна, дв. ход./мин.</td><td></td></tr>
<tr><td>15.</td><td>Поперечнострогальный станок</td><td>7Е35</td><td>500</td><td>13,2 - 150</td><td>5,5</td></tr>
<tr><td>16.</td><td>То же</td><td>7310Д</td><td>1000</td><td>3 - 48</td><td>11,0</td></tr>
<tr><td colspan="3"></td><td>Наибольший ход долбяка, мм</td><td>Частота движения долбяка, дв. ход./мин.</td><td></td></tr>
<tr><td>17.</td><td>Долбежный станок</td><td>7А420М</td><td>200</td><td>40 - 163</td><td>3,0</td></tr>
<tr><td>18.</td><td>То же</td><td>7Д430</td><td>320</td><td>3 - 38</td><td>7,5</td></tr>
<tr><td>19.</td><td>То же</td><td>7Д450</td><td>500</td><td>5 - 30</td><td>10</td></tr>
</table>


<a id="p100161"></a>2.2. Транспортные средства, приспособления, оснастка применяются универсальные.
<a id="p100162"></a>2.3. В ремонтных цехах и мастерских разрабатываются маршрутные технологические процессы и нормы времени устанавливаются по укрупненным нормативам на операцию по видам работ (фрезерная, строгальная, долбежная и т.п.).
<a id="p100163"></a>2.4. При проектировании нормативов учитывались характеристики обрабатываемого материала, режим работы оборудования, количество одновременно обрабатываемых деталей, шероховатость и точность обработки.


### 3. <a id="p100164"></a>Организация труда


<a id="p100165"></a>Нормативы времени рассчитаны на организацию труда в ремонтно-механических цехах и мастерских с единичным типом производства.
<a id="p100166"></a>Условия работы характеризуются широкой номенклатурой и малым количеством изготовляемых деталей.
<a id="p100167"></a>При изготовлении нормализованных деталей, имеющих общее назначение в конструкциях различного ремонтируемого оборудования, имеется возможность организовать изготовление деталей мелкими партиями (мелкосерийный тип производства).
<a id="p100168"></a>Изготовление деталей осуществляется по картам маршрутной технологии или по детали-образцу. Режимы резания в картах технологического процесса не проставляются.
<a id="p100169"></a>Рабочее место станочников оснащается всем необходимым, с соблюдением правил санитарии и гигиены, техники безопасности.
<a id="p100170"></a>Освещение рабочих мест должно быть достаточным и правильным. Требуемая освещенность определяется характером выполняемой работы и действующими санитарными нормами. При местном освещении свет не должен слепить глаза, тень не должна падать на обрабатываемую деталь.
<a id="p100171"></a>Инструменты и приспособления необходимо располагать на рабочем месте в определенном, удобном для пользования порядке.
<a id="p100172"></a>Рабочее место оснащается:
- <a id="p100173"></a>тумбочкой, стеллажом, тарой для хранения технологической оснастки, заготовок и готовой продукции;
- <a id="p100174"></a>комплектом приспособлений и принадлежностей технологической оснастки (тиски, универсальные и специальные зажимные приспособления, оправки, державки, ключи и т.п.);
- <a id="p100175"></a>комплектом постоянно применяемых режущих и измерительных инструментов.
<a id="p100176"></a>Нормативы времени рассчитаны на организацию производства, при которой исполнителем выполняется следующая работа:
- <a id="p100177"></a>заточка режущих инструментов, за исключением сложной формы;
- <a id="p100178"></a>получение наряда, чертежей, технологической документации;
- <a id="p100179"></a>подбор материалов и заготовок, перемещение их к рабочему месту на расстояние 20 м, отправление и сдача готовых деталей;
- <a id="p100180"></a>получение и сдача инструментов, приспособлений в инструментальной раздаточной кладовой;
- <a id="p100181"></a>наладка оборудования и необходимые в процессе обработки вспомогательные работы.
<a id="p100182"></a>Технический инструктаж проводится на рабочем месте мастером.
<a id="p100183"></a>Размещение на рабочем месте основного, вспомогательного оборудования и оргоснастки должно обеспечивать:
- <a id="p100184"></a>подъезд средств внутрицехового и межоперационного транспорта;
- <a id="p100185"></a>свободный доступ к зонам, требующим профилактического осмотра и ремонта;
- <a id="p100186"></a>хороший обзор шкал и приборов, досягаемость органов управления;
- <a id="p100187"></a>возможность организации многостаночного обслуживания.
<a id="p100188"></a>Ниже приведены примеры планировок рабочих мест станочников (рисунки не приводятся).


#### <a id="p100189"></a>РАБОЧЕЕ МЕСТО ФРЕЗЕРОВЩИКА



##### <a id="p100190"></a>Рис. 3. Вертикально-фрезерный станок

<a id="p100191"></a>1 - тумбочка инструментальная двухсекционная С3746.05; 2 - стол производственный С3702.51; 3 - стеллаж для приспособлений СД3725.01А; 4 - стеллаж-подставка СД3702.10А; 5 - тара производственная; 6 - планшет для чертежей СД3750.04; 7 - щит экранный; 8 - решетка под ноги рабочему; 9 - место рабочего.


##### <a id="p100192"></a>Рис. 4. Горизонтально-фрезерный станок

<a id="p100193"></a>1 - тумбочка инструментальная двухсекционная С3746.05; 2 - стол производственный С3702.51; 3 - стеллаж для приспособлений СД3725.01А; 4 - стеллаж для вертикального хранения СМ3721.16; 5 - стеллаж-подставка СД3702.10А; 6 - тара производственная; 7 - планшет для чертежей СД3750.04; 8 - решетка под ноги рабочему; 9 - место рабочего.


##### <a id="p100194"></a>Рис. 5. Универсально-фрезерный станок

<a id="p100195"></a>1 - тумбочка инструментальная двухсекционная С3746.05; 2 - стол производственный С3702.51; 3 - стеллаж для приспособлений СД3725.01А; 4 - стеллаж для вертикального хранения СМ3721.16; 5 - стеллаж-подставка СД3702.10А; 6 - тара производственная; 7 - планшет для чертежей СД3750.04; 8 - решетка под ноги рабочему; 9 - место рабочего.


#### <a id="p100196"></a>РАБОЧЕЕ МЕСТО СТРОГАЛЬЩИКА



##### <a id="p100197"></a>Рис. 6. Поперечно-строгальный станок

<a id="p100198"></a>1 - тумбочка инструментальная двухсекционная С3746.05; 2 - стол производственный С3702.51; 3 - стеллаж-подставка СД3702.10А; 4 - тара производственная; 5 - планшет для чертежей СД3750.04; 6 - решетка под ноги рабочему; 7 - место рабочего.


##### <a id="p100199"></a>Рис. 7. Продольно-строгальный станок

<a id="p100200"></a>1 - шкаф инструментальный СМ3712.09; 2 - площадка к станку СМ3744.11; 3 - стеллаж-подставка СД3702.10А; 4 - подставка под корпусные детали СД3738.05; 5 - планшет для чертежей СМ3799.05; 6 - решетка под ноги рабочему; 7 - место рабочего.


#### <a id="p100201"></a>ОРГОСНАСТКА РАБОЧИХ МЕСТ


<a id="p100202"></a>Оснащение рабочих мест станочников оргоснасткой (инструментальными тумбочками, приемными столиками и т.д.) должно производиться на основе типовых конструкций.
<a id="p100203"></a>Специальная оргоснастка проектируется в исключительных случаях, если по тем или иным причинам не подходит типовая.
<a id="p100204"></a>Ниже в качестве примера приведены отдельные конструкции типовой оргоснастки (рисунки не приводятся).


##### <a id="p100205"></a>Рис. 8. Тумбочка инструментальная двухсекционная С3746.05

<a id="p100206"></a>Тумбочка предназначена для хранения необходимого инструмента на рабочих местах станочников, документации и средств по уходу за оборудованием.
<a id="p100207"></a>Каждое отделение тумбочки закрывается дверцей и закрепляется за одним рабочим. В каждом отделении имеются ящики для инструмента и полки для хранения документации, небольших принадлежностей и приспособлений, масленок, обтирочных материалов и др. Верхняя полка тумбочки может быть покрыта пластиком. Съемный планшет для крепления чертежей закрепляется в кронштейнах.


##### <a id="p100208"></a>Рис. 9. Стол производственный С3702.51

<a id="p100209"></a>На верхней полке стола размещается тара с обрабатываемыми деталями или сами детали. При необходимости на нижней полке могут храниться приспособления и принадлежности.
<a id="p100210"></a>На отдельных рабочих местах стол может быть использован для раскладки на нем непосредственно используемого в работе инструмента.


##### <a id="p100211"></a>Рис. 10. Столик приемный передвижной С3705.02А

<a id="p100212"></a>Столик предназначен для размещения деталей, легких приспособлений, тары с заготовками. Он используется на тех рабочих местах, где по условиям работы стационарная оргоснастка (инструментальные тумбочки или столы приемные) не может быть установлена достаточно близко и удобно около станка.


##### <a id="p100213"></a>Рис. 11. Шкаф инструментальный СМ3712.09

<a id="p100214"></a>Шкаф предназначен для оснащения рабочих мест станочников. В нем хранятся необходимый на рабочем месте инструмент, техническая документация, средства по уходу за оборудованием.


##### <a id="p100215"></a>Рис. 12. Стеллаж для приспособлений (с выдвижной платформой) СД3725.01А

<a id="p100216"></a>Стеллаж устанавливается на рабочих местах станочников, работающих на горизонтально-фрезерном, вертикально-фрезерном, универсально-фрезерном станках и предназначен для хранения приспособлений. Грузоподъемность стеллажа до 300 кг.


### 4. <a id="p100217"></a>Нормативная часть



<a id="p100218"></a>

```text
┌────────────────────────────────────┬──────────────────────────────────┐
│Поправочные коэффициенты на штучное │            Все станки            │
│              время                 ├───────────────┬──────────────────┤
│                                    │    Карта 1    │      лист 1      │
├────────────────────────────────────┴───────────────┴──────────────────┤
│  1. Поправочные коэффициенты в зависимости от числа деталей в партии  │
├──────────────────────┬─────┬─────┬──────┬───────┬───────┬───────┬─────┤
│Число деталей в       │1 - 2│3...5│6...10│11...20│21...40│41...90│свыше│
│партии <*>            │     │     │      │       │       │       │  90 │
├─────┬────────────────┼─────┼─────┼──────┼───────┼───────┼───────┼─────┤
│Коэф-│при обработке на│1,0  │0,9  │ 0,8  │ 0,75  │  0,7  │  0,6  │ 0,55│
│фици-│станках с ручным│     │     │      │       │       │       │     │
│ент  │управлением     │     │     │      │       │       │       │     │
│К    ├────────────────┼─────┼─────┼──────┼───────┼───────┼───────┼─────┤
│ п   │при обработке на│1,0  │0,98 │ 0,95 │ 0,92  │  0,9  │ 0,86  │ 0,85│
│     │станках с       │     │     │      │       │       │       │     │
│     │полуавтоматичес-│     │     │      │       │       │       │     │
│     │ким циклом      │     │     │      │       │       │       │     │
│     │(зубообрабатыва-│     │     │      │       │       │       │     │
│     │ющие, дисковые  │     │     │      │       │       │       │     │
│     │пилы и т.д.)    │     │     │      │       │       │       │     │
├─────┴────────────────┴─────┴─────┴──────┴───────┴───────┴───────┴─────┤
│           2. Поправочные коэффициенты в зависимости от числа          │
│                         обслуживаемых станков                         │
├──────────────────┬───────────┬────────────────────────────────────────┤
│  Коэффициент     │   Форма   │ Количество станков, обслуживаемых одним│
│занятости, К , до │организации│                 рабочим                │
│            з     │   труда   ├─────────────┬──────────────┬───────────┤
│                  │           │      2      │      3       │      4    │
│                  │           ├─────────────┴──────────────┴───────────┤
│                  │           │ Коэффициент изменения штучного времени,│
│                  │           │                   К                    │
│                  │           │                    ос                  │
├──────────────────┼───────────┼─────────────┬──────────────┬───────────┤
│0,25              │Индивиду-  │0,56         │0,39          │0,33       │
│0,35              │альная     │0,65         │0,48          │0,39       │
│0,45              │           │0,75         │0,55          │0,47       │
├──────────────────┼───────────┼─────────────┼──────────────┼───────────┤
│0,25              │Бригадная  │0,53         │0,37          │0,30       │
│0,35              │           │0,60         │0,44          │0,37       │
│0,45              │           │0,67         │0,51          │0,45       │
├──────────────────┴───────────┴────────┬────┴──────────────┴───────────┤
│ Поправочные коэффициенты на штучное   │           Все станки          │
│                время                  ├────────────┬──────────────────┤
│                                       │  Карта 1   │      лист 2      │
├───────────────────────────────────────┴────────────┴──────────────────┤
│    3. Поправочные коэффициенты в зависимости от организации труда     │
│                              рабочих мест                             │
├───────────────────────────────────────────────────────────────────────┤
│               Организация рабочих мест на предприятиях                │
├───────────────────────────────┬───────────────────────────────────────┤
│           1 группа            │               2 группа                │
├───────────────────────────────┴───────────────────────────────────────┤
│                           Коэффициент К                               │
│                                        орм                            │
├───────────────────────────────┬───────────────────────────────────────┤
│              1,0              │                  0,8                  │
└───────────────────────────────┴───────────────────────────────────────┘
```



<a id="p100233"></a>

---

<a id="p100234"></a><*> При одновременной установке на станок нескольких деталей эта величина определяется как частное от деления числа деталей в партии на число одновременно устанавливаемых деталей.

<a id="p100235"></a>1 группа - предприятия, на которых получение, доставка и сдача заготовок, деталей, инструмента, приспособлений, а также заточка инструмента производится самим станочником.
<a id="p100236"></a>2 группа - предприятия, на которых рабочее место обслуживают вспомогательные рабочие, заточка инструмента - централизована.
<a id="p100237"></a>*Примечание.* При изготовлении деталей по образцу (отсутствие маршрутной карты и эскиза) приведенные в картах сборника нормативы времени следует применять с коэффициентом К = 1,2.


<a id="p100238"></a>

<table>
<colgroup><col width="6%"><col width="34%"><col width="22%"><col width="5%"><col width="6%"><col width="28%"></colgroup>
<tr><td colspan="4" rowspan="2">Подготовительно-заключительное время</td><td colspan="2">Все станки</td></tr>
<tr><td colspan="2">Карта 2</td></tr>
<tr><td>N позиции</td><td>Тип станков</td><td colspan="3">Основные параметры станков</td><td>Подготовительнозаключительное время в % от штучного времени</td></tr>
<tr><td>1</td><td>Горизонтально-верти-</td><td>Длина стола,</td><td colspan="2">750</td><td>7,0</td></tr>
<tr><td>2</td><td>кально-фрезерные</td><td>мм, до</td><td colspan="2">1600</td><td>8,0</td></tr>
<tr><td>3</td><td></td><td></td><td colspan="2">2500</td><td>9,0</td></tr>
<tr><td>4</td><td>Продольно-фрезерные и</td><td>Длина стола</td><td colspan="2">3000</td><td>7,5</td></tr>
<tr><td>5</td><td>строгальные</td><td>мм, до</td><td colspan="2">6000</td><td>8,5</td></tr>
<tr><td>6</td><td>Поперечно-строгальные</td><td>Длина хода</td><td colspan="2">500</td><td>5,5</td></tr>
<tr><td>7</td><td></td><td>ползуна, мм,</td><td colspan="2">750</td><td>6,0</td></tr>
<tr><td>8</td><td></td><td>до</td><td colspan="2">1000</td><td>6,5</td></tr>
<tr><td>9</td><td>Долбежные</td><td>Длина хода</td><td colspan="2">500</td><td>5,5</td></tr>
<tr><td>10</td><td></td><td>ползуна, мм,</td><td colspan="2">1000</td><td>6,5</td></tr>
<tr><td>11</td><td></td><td>до</td><td colspan="2">1400</td><td>7,0</td></tr>
</table>



#### <a id="p100251"></a>4.1. Горизонтально-вертикально-продольно-фрезерные станки


<a id="p100252"></a>Вспомогательное время на установку и снятие детали


<a id="p100253"></a>

<table>
<colgroup><col width="4%"><col width="29%"><col width="17%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"><col width="5%"></colgroup>
<tr><td rowspan="2"></td><td colspan="8" rowspan="2">Вспомогательное время на установку и снятие детали при работе на столе или в приспособлении</td><td colspan="7">Горизонтально-вертикально- и продольно-фрезерные станки</td></tr>
<tr><td colspan="7">Карта 3</td></tr>
<tr><td rowspan="4">N позиции</td><td>Способ установки и крепления детали</td><td rowspan="4">Характер выверки</td><td colspan="6">Вручную</td><td colspan="7">Мостовым краном</td></tr>
<tr><td rowspan="3">(рисунки не приводятся)</td><td colspan="13">Масса детали, кг, до</td></tr>
<tr><td>1</td><td>3</td><td>5</td><td>10</td><td>20</td><td>30</td><td>30</td><td>50</td><td>100</td><td>200</td><td>400</td><td>800</td><td>1500</td></tr>
<tr><td colspan="13">Время, t , мин. ву</td></tr>
<tr><td>1</td><td>В тисках с креплением винтом</td><td>без выверки</td><td>0,6</td><td>0,7</td><td>0,8</td><td>1,0</td><td>1,2</td><td>1,4</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td></td><td>с выверкой в одной плоскости</td><td>1,1</td><td>1,5</td><td>1,7</td><td>2,0</td><td>2,3</td><td>2,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td></td><td>с выверкой в двух плоскостях</td><td>2,5</td><td>3,2</td><td>3,5</td><td>4,0</td><td>4,3</td><td>5,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>На столе, крепление болтами и</td><td>без выверки</td><td>1,0</td><td>1,4</td><td>1,6</td><td>1,8</td><td>2,3</td><td>3,0</td><td>5,0</td><td>5,8</td><td>6,6</td><td>7,7</td><td>8,8</td><td>10,5</td><td>12</td></tr>
<tr><td>5</td><td>планками</td><td>с выверкой в одной плоскости</td><td>2,0</td><td>2,6</td><td>3,0</td><td>3,5</td><td>4,2</td><td>4,7</td><td>8,6</td><td>9,7</td><td>11</td><td>13</td><td>15</td><td>18</td><td>20</td></tr>
<tr><td>6</td><td></td><td>с выверкой в двух плоскостях</td><td>2,8</td><td>3,6</td><td>4,3</td><td>4,8</td><td>5,7</td><td>6,3</td><td>13</td><td>15</td><td>17</td><td>20</td><td>21</td><td>24</td><td>28</td></tr>
<tr><td>7</td><td>На столе с домкратами, подстав-</td><td>без выверки</td><td>1,4</td><td>1,8</td><td>2,1</td><td>2,7</td><td>3,2</td><td>3,8</td><td>6,4</td><td>7,5</td><td>8,6</td><td>10,4</td><td>12</td><td>13</td><td>16</td></tr>
<tr><td>8</td><td>ками, крепление болтами и планками</td><td>с выверкой в одной плоскости</td><td>2,4</td><td>3,4</td><td>3,8</td><td>4,8</td><td>5,2</td><td>5,8</td><td>10</td><td>11</td><td>14</td><td>16</td><td>19</td><td>23</td><td>25</td></tr>
<tr><td>9</td><td></td><td>с выверкой в двух плоскостях</td><td>3,0</td><td>4,0</td><td>5,0</td><td>5,5</td><td>6,8</td><td>7,5</td><td>14</td><td>16</td><td>18</td><td>21</td><td>24</td><td>29</td><td>32</td></tr>
<tr><td>10</td><td>На столе с угольником, крепле-</td><td>без выверки</td><td>1,4</td><td>1,7</td><td>2,0</td><td>2,4</td><td>2,8</td><td>3,5</td><td>6,2</td><td>8,2</td><td>9,2</td><td>9,6</td><td>10</td><td>12</td><td>13</td></tr>
<tr><td>11</td><td>ние болтами и планками</td><td>с выверкой в одной плоскости</td><td>2,1</td><td>3,0</td><td>3,4</td><td>4,0</td><td>4,5</td><td>5,5</td><td>11</td><td>12</td><td>14</td><td>16</td><td>18</td><td>21</td><td>24</td></tr>
<tr><td>12</td><td></td><td>с выверкой в двух плоскостях</td><td>3,1</td><td>4,2</td><td>4,9</td><td>5,6</td><td>6,7</td><td>7,8</td><td>14</td><td>16</td><td>19</td><td>21</td><td>24</td><td>29</td><td>32</td></tr>
<tr><td>13</td><td>На призмах с креплением</td><td>без выверки</td><td>1,1</td><td>1,7</td><td>1,8</td><td>2,1</td><td>2,7</td><td>3,5</td><td>4,5</td><td>4,7</td><td>5,8</td><td>6,5</td><td>8,4</td><td>9,6</td><td>-</td></tr>
<tr><td>14</td><td>болтами и планками</td><td>с выверкой в одной плоскости</td><td>2,2</td><td>3,0</td><td>3,4</td><td>4,0</td><td>5,0</td><td>6,0</td><td>7,5</td><td>8,6</td><td>9,6</td><td>12</td><td>14</td><td>18</td><td>21</td></tr>
<tr><td colspan="3">Время в карте предусматривает крепление детали болтами в количестве</td><td colspan="12">4</td><td>6</td></tr>
<tr><td colspan="3">Добавлять (отнимать) на каждый болт сверх (менее) предусмотренных</td><td colspan="3">0,4</td><td colspan="4">0,6</td><td colspan="5">0,7</td><td>1,1</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>


<a id="p100274"></a>Примечания: 1. При установке деталей с необработанной поверхностью (литье, поковка) время по карте следует применять с коэффициентом К = 1,2.
2. <a id="p100275"></a>При переустановке деталей вручную время по карте следует применять без изменений, мостовым краном - с коэффициентом К = 0,8.
3. <a id="p100276"></a>При установке одновременно двух - четырех деталей время по карте для каждой последующей детали за первой следует применять с коэффициентом К = 0,8.


<a id="p100277"></a>

<table>
<colgroup><col width="6%"><col width="17%"><col width="25%"><col width="8%"><col width="8%"><col width="8%"><col width="6%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="3">Вспомогательное время на установку и снятие детали при работе в центрах с делительной головкой и в самоцентрирующем</td><td colspan="7">Горизонтально-вертикально- и продольно-фрезерные станки</td></tr>
<tr><td colspan="3">патроне</td><td colspan="7">Карта 4</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Способ установки (рисунки не приводятся)</td><td colspan="7">Масса детали, кг, до</td></tr>
<tr><td>1</td><td>3</td><td>5</td><td>8</td><td>12</td><td>20</td><td>30</td></tr>
<tr><td colspan="7">Время, мин.</td></tr>
<tr><td>1</td><td></td><td>В центрах с делительной головкой</td><td>0,7</td><td>1,1</td><td>1,2</td><td>1,5</td><td>1,7</td><td>2,0</td><td>2,3</td></tr>
<tr><td>2</td><td></td><td>В центрах на оправке с делительной головкой</td><td>1,3</td><td>1,9</td><td>2,2</td><td>2,5</td><td>2,9</td><td>3,4</td><td>3,9</td></tr>
<tr><td>3</td><td colspan="2">На каждую последующую деталь при одновременной обработке нескольких деталей</td><td>0,12</td><td>0,24</td><td>0,4</td><td>0,4</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td></td><td>В самоцентрирующем патроне с делительной головкой с поджатием центром задней бабки или с поддержкой домкратом, люнетом</td><td>0,6</td><td>0,9</td><td>1,1</td><td>1,3</td><td>1,5</td><td>1,8</td><td>-</td></tr>
<tr><td>5</td><td></td><td>В самоцентрирующем патроне с делительной головкой с поджатием центром задней бабки и поддержкой домкратом или люнетом</td><td>1,1</td><td>1,5</td><td>1,7</td><td>2,0</td><td>2,2</td><td>2,5</td><td>-</td></tr>
<tr><td>6</td><td></td><td>В самоцентрирующем патроне</td><td>0,6</td><td>0,8</td><td>1,0</td><td>1,2</td><td>1,4</td><td>1,7</td><td>-</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td></tr>
</table>


<a id="p100286"></a>Примечание: При переустановке деталей вручную время по карте следует применять без изменений.


##### <a id="p100287"></a>Неполное штучное время



###### <a id="p100288"></a>4.1.1. Горизонтально- и вертикально-фрезерные станки



<a id="p100289"></a>

<table>
<colgroup><col width="5%"><col width="14%"><col width="4%"><col width="8%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="8" rowspan="3">Неполное штучное время Фрезерование плоскостей Чугун серый, НВ = 1760...2150 МПа</td><td colspan="9">Горизонтально- и вертикально-фрезерные станки</td></tr>
<tr><td colspan="9">Фрезы торцовые с пластинками ВК8</td></tr>
<tr><td colspan="9">Карта 5</td></tr>
<tr><td colspan="17">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Характер обработки</td><td colspan="2" rowspan="3">Ширина обрабатываемой поверхности, В, мм</td><td rowspan="2">Число рабочих ходов,</td><td colspan="12">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td colspan="2">600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>i</td><td colspan="12">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td colspan="2">50</td><td>1</td><td>1,5</td><td>1,7</td><td>1,9</td><td>1,2</td><td>2,4</td><td>2,6</td><td>2,9</td><td colspan="2">3,2</td><td>3,4</td><td>3,5</td><td>3,9</td></tr>
<tr><td>2</td><td>14...12</td><td colspan="2">75</td><td></td><td>1,7</td><td>1,9</td><td>2,2</td><td>2,4</td><td>2,7</td><td>3,0</td><td>3,3</td><td colspan="2">3,7</td><td>4,1</td><td>4,5</td><td>4,8</td></tr>
<tr><td>3</td><td>квалитет</td><td colspan="2">110</td><td></td><td>2,1</td><td>2,4</td><td>2,8</td><td>3,2</td><td>3,6</td><td>4,0</td><td>4,5</td><td colspan="2">5,1</td><td>5,6</td><td>6,1</td><td>6,7</td></tr>
<tr><td>4</td><td></td><td colspan="2">150</td><td></td><td>2,4</td><td>2,8</td><td>3,2</td><td>3,6</td><td>4,2</td><td>4,8</td><td>5,4</td><td colspan="2">6,0</td><td>6,7</td><td>7,7</td><td>8,8</td></tr>
<tr><td>5</td><td></td><td colspan="2">200</td><td></td><td>2,8</td><td>3,2</td><td>3,7</td><td>4,3</td><td>4,9</td><td>5,6</td><td>6,5</td><td colspan="2">7,5</td><td>8,6</td><td>10</td><td>11</td></tr>
<tr><td>6</td><td></td><td colspan="2">250</td><td></td><td>3,2</td><td>3,7</td><td>4,3</td><td>5,1</td><td>5,9</td><td>6,8</td><td>8,0</td><td colspan="2">9,3</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>7</td><td>Rz 40...</td><td colspan="2">50</td><td>2</td><td>4,7</td><td>5,2</td><td>5,8</td><td>6,4</td><td>7,1</td><td>7,7</td><td>8,3</td><td colspan="2">8,9</td><td>9,3</td><td>9,7</td><td>10</td></tr>
<tr><td>8</td><td>Rz 20;</td><td colspan="2">75</td><td></td><td>5,2</td><td>5,8</td><td>6,4</td><td>7,1</td><td>7,9</td><td>8,7</td><td>9,5</td><td colspan="2">10</td><td>11</td><td>12</td><td>13</td></tr>
<tr><td>9</td><td>11 квали-</td><td colspan="2">110</td><td></td><td>6,3</td><td>6,8</td><td>7,4</td><td>8,2</td><td>9,0</td><td>9,8</td><td>11</td><td colspan="2">12</td><td>14</td><td>15</td><td>16</td></tr>
<tr><td>10</td><td>тет</td><td colspan="2">150</td><td></td><td>6,8</td><td>7,5</td><td>8,3</td><td>9,3</td><td>10</td><td>12</td><td>13</td><td colspan="2">14</td><td>16</td><td>17</td><td>19</td></tr>
<tr><td>11</td><td></td><td colspan="2">200</td><td></td><td>7,8</td><td>8,6</td><td>9,5</td><td>11</td><td>12</td><td>13</td><td>14</td><td colspan="2">16</td><td>17</td><td>19</td><td>22</td></tr>
<tr><td>12</td><td></td><td colspan="2">250</td><td></td><td>9,0</td><td>10</td><td>11</td><td>12</td><td>14</td><td>16</td><td>17</td><td colspan="2">20</td><td>22</td><td>25</td><td>27</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">Твердости обрабатываемого</td><td colspan="5">Твердость, НВ, МПа</td><td colspan="5">до 2150</td><td colspan="4">св. 2150</td></tr>
<tr><td colspan="3">материала</td><td colspan="5">Коэффициент К тв</td><td colspan="5">1,0</td><td colspan="4">1,2</td></tr>
<tr><td colspan="3" rowspan="2">Мощности привода станка</td><td colspan="5">N, кВт</td><td colspan="3">4,5</td><td colspan="6">7,5 св. 10</td></tr>
<tr><td colspan="5">Коэффициент К N</td><td colspan="3">1,2</td><td colspan="6">1,1 1,0</td></tr>
</table>


<a id="p100309"></a>Примечания: 1. При фрезеровании одновременно нескольких заготовок ширина обрабатываемой поверхности (или длина) и, соответственно, время на обработку определяются с учетом количества деталей, установленных на станке.
2. <a id="p100310"></a>При предварительном фрезеровании по корке время на поверхность для Rz 80 следует применять с коэффициентом К = 1,2.


<a id="p100311"></a>

<table>
<colgroup><col width="4%"><col width="6%"><col width="8%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="5%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"></colgroup>
<tr><td colspan="16" rowspan="3">Неполное штучное время Фрезерование плоскостей Сталь конструкционная, сигма = 590...740 МПа в</td><td colspan="12">Горизонтально- и вертикально-фрезерные станки</td></tr>
<tr><td colspan="12">Фрезы торцовые из стали Р6М5</td></tr>
<tr><td colspan="12">Карта 6</td></tr>
<tr><td colspan="28">рисунок не приводится</td></tr>
<tr><td rowspan="4">N позиции</td><td rowspan="2">Шероховатость и</td><td rowspan="4">Ширина обрабатываемой поверхности, В, мм</td><td colspan="13">Заготовка из проката</td><td colspan="12">Поковка или отливка</td></tr>
<tr><td colspan="25">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">точность</td><td>100</td><td>150</td><td colspan="2">200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td colspan="2">800</td><td>1000</td><td>100</td><td>150</td><td colspan="2">200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td colspan="25">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>50</td><td>2,3</td><td>2,7</td><td colspan="2">3,2</td><td>3,7</td><td>4,4</td><td>5,1</td><td>6,0</td><td>7,2</td><td>8,4</td><td colspan="2">9,3</td><td>10,5</td><td>4,8</td><td>5,7</td><td colspan="2">6,7</td><td>7,8</td><td>9,2</td><td>11</td><td>13</td><td>15</td><td>18</td><td>20</td><td>22</td></tr>
<tr><td>2</td><td>14...</td><td>75</td><td>2,6</td><td>3,1</td><td colspan="2">3,6</td><td>4,2</td><td>5,0</td><td>6,0</td><td>7,2</td><td>8,5</td><td>9,8</td><td colspan="2">11</td><td>12,5</td><td>5,5</td><td>6,5</td><td colspan="2">7,6</td><td>8,8</td><td>11</td><td>13</td><td>15</td><td>18</td><td>21</td><td>23</td><td>26</td></tr>
<tr><td>3</td><td>12</td><td>110</td><td>3,0</td><td>3,6</td><td colspan="2">4,2</td><td>4,8</td><td>5,7</td><td>6,5</td><td>8,0</td><td>9,5</td><td>11</td><td colspan="2">12</td><td>14</td><td>6,3</td><td>7,6</td><td colspan="2">8,8</td><td>10</td><td>12</td><td>14</td><td>17</td><td>20</td><td>23</td><td>25</td><td>29</td></tr>
<tr><td>4</td><td>квали-</td><td>150</td><td>3,2</td><td>3,8</td><td colspan="2">4,5</td><td>5,2</td><td>6,3</td><td>7,4</td><td>8,2</td><td>10</td><td>12</td><td colspan="2">13</td><td>15</td><td>6,7</td><td>8,0</td><td colspan="2">9,5</td><td>11</td><td>13</td><td>16</td><td>18</td><td>21</td><td>25</td><td>27</td><td>31</td></tr>
<tr><td>5</td><td>тет</td><td>200</td><td>3,7</td><td>4,3</td><td colspan="2">5,1</td><td>5,9</td><td>7,0</td><td>8,4</td><td>9,7</td><td>11</td><td>13</td><td colspan="2">15</td><td>17</td><td>7,8</td><td>9,0</td><td colspan="2">11</td><td>12</td><td>15</td><td>18</td><td>20</td><td>23</td><td>27</td><td>31</td><td>36</td></tr>
<tr><td>6</td><td></td><td>250</td><td>4,2</td><td>5,1</td><td colspan="2">6,0</td><td>7,0</td><td>8,5</td><td>10</td><td>11</td><td>13</td><td>15</td><td colspan="2">17</td><td>20</td><td>9,0</td><td>11</td><td colspan="2">12</td><td>15</td><td>18</td><td>20</td><td>23</td><td>27</td><td>32</td><td>36</td><td>40</td></tr>
<tr><td></td><td colspan="2">Число рабочих ходов</td><td colspan="13">1</td><td colspan="12">2</td></tr>
<tr><td>7</td><td>Rz 40,</td><td>50</td><td>6,3</td><td>7,2</td><td colspan="2">8,3</td><td>9,0</td><td>11</td><td>12</td><td>14</td><td>16</td><td>18</td><td colspan="2">20</td><td>22</td><td>8,8</td><td>10</td><td colspan="2">12</td><td>14</td><td>16</td><td>18</td><td>21</td><td>24</td><td>27</td><td>30</td><td>34</td></tr>
<tr><td>8</td><td>Rz 20;</td><td>75</td><td>7,3</td><td>8,4</td><td colspan="2">9,5</td><td>11</td><td>12</td><td>14</td><td>17</td><td>19</td><td>22</td><td colspan="2">24</td><td>26</td><td>10</td><td>12</td><td colspan="2">14</td><td>17</td><td>19</td><td>21</td><td>24</td><td>28</td><td>33</td><td>36</td><td>40</td></tr>
<tr><td>9</td><td>11</td><td>110</td><td>9,5</td><td>11</td><td colspan="2">12</td><td>14</td><td>16</td><td>18</td><td>21</td><td>25</td><td>28</td><td colspan="2">31</td><td>35</td><td>13</td><td>15</td><td colspan="2">17</td><td>19</td><td>22</td><td>25</td><td>30</td><td>35</td><td>40</td><td>43</td><td>49</td></tr>
<tr><td>10</td><td>квали-</td><td>150</td><td>11</td><td>13</td><td colspan="2">14</td><td>16</td><td>18</td><td>20</td><td>23</td><td>28</td><td>31</td><td colspan="2">35</td><td>40</td><td>15</td><td>17</td><td colspan="2">20</td><td>22</td><td>25</td><td>29</td><td>32</td><td>39</td><td>45</td><td>49</td><td>56</td></tr>
<tr><td>11</td><td>тет</td><td>200</td><td>14</td><td>15</td><td colspan="2">17</td><td>19</td><td>22</td><td>25</td><td>29</td><td>33</td><td>38</td><td colspan="2">42</td><td>47</td><td>18</td><td>20</td><td colspan="2">23</td><td>25</td><td>30</td><td>35</td><td>39</td><td>45</td><td>52</td><td>58</td><td>66</td></tr>
<tr><td>12</td><td></td><td>250</td><td>15</td><td>17</td><td colspan="2">19</td><td>22</td><td>25</td><td>28</td><td>32</td><td>38</td><td>42</td><td colspan="2">47</td><td>52</td><td>20</td><td>23</td><td colspan="2">25</td><td>30</td><td>35</td><td>40</td><td>45</td><td>52</td><td>58</td><td>66</td><td>75</td></tr>
<tr><td></td><td colspan="2">Число рабочих ходов</td><td colspan="13">2</td><td colspan="12">3</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td>п</td><td>р</td><td>с</td><td>т</td><td>у</td><td>ф</td><td>х</td><td>ц</td></tr>
<tr><td colspan="28">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6">1. Предела прочности обрабатываемого материала</td><td colspan="8">Прочность, сигма , МПа в Коэффициент К пп</td><td colspan="5">до 590 0,9</td><td colspan="5">590...740 1,0</td><td colspan="4">св. 740 1,2</td></tr>
<tr><td colspan="6">2. Мощности привода станка</td><td colspan="8">N, кВт Коэффициент К N</td><td colspan="5">4,5 1,2</td><td colspan="5">7,0 1,1</td><td colspan="4">10 1,0</td></tr>
</table>


<a id="p100333"></a>Примечание: При фрезеровании одновременно нескольких заготовок ширина обрабатываемой поверхности (или длина) и, соответственно, время на обработку определяются с учетом количества деталей, установленных на станке.


<a id="p100334"></a>

<table>
<colgroup><col width="4%"><col width="6%"><col width="8%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"></colgroup>
<tr><td colspan="15" rowspan="3">Неполное штучное время Фрезерование плоскостей Сталь конструкционная, сигма = 590...740 МПа в</td><td colspan="12">Горизонтально- и вертикально-фрезерные станки</td></tr>
<tr><td colspan="12">Фрезы торцовые с пластинками Т5К10</td></tr>
<tr><td colspan="12">Карта 7</td></tr>
<tr><td colspan="27">рисунок не приводится</td></tr>
<tr><td rowspan="4">N позиции</td><td>Характер</td><td rowspan="4">Ширина обрабатываемой поверхности, В, мм</td><td colspan="12">Заготовка из проката</td><td colspan="12">Поковка или отливка</td></tr>
<tr><td rowspan="3">обработки</td><td colspan="24">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td colspan="2">1000</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td colspan="2">500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td colspan="24">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80,</td><td>50</td><td>2,1</td><td>2,5</td><td>2,9</td><td>3,3</td><td>3,9</td><td>4,6</td><td>5,3</td><td>6,1</td><td>6,9</td><td>7,3</td><td colspan="2">8,7</td><td>4,6</td><td>5,5</td><td>6,4</td><td>7,3</td><td>8,6</td><td>10</td><td colspan="2">12</td><td>13</td><td>15</td><td>16</td><td>19</td></tr>
<tr><td>2</td><td>14...</td><td>75</td><td>2,3</td><td>2,7</td><td>3,1</td><td>3,7</td><td>4,4</td><td>5,2</td><td>6,0</td><td>7,2</td><td>8,4</td><td>9,6</td><td colspan="2">11</td><td>5,1</td><td>5,9</td><td>6,8</td><td>8,1</td><td>9,7</td><td>11</td><td colspan="2">13</td><td>15</td><td>18</td><td>21</td><td>24</td></tr>
<tr><td>3</td><td>12</td><td>110</td><td>2,8</td><td>3,3</td><td>3,8</td><td>4,5</td><td>5,3</td><td>6,1</td><td>7,2</td><td>8,4</td><td>9,6</td><td>11</td><td colspan="2">12</td><td>6,2</td><td>7,3</td><td>8,4</td><td>9,9</td><td>11</td><td>13</td><td colspan="2">16</td><td>18</td><td>21</td><td>24</td><td>26</td></tr>
<tr><td>4</td><td>квали-</td><td>150</td><td>3,0</td><td>3,5</td><td>4,1</td><td>4,8</td><td>5,6</td><td>6,6</td><td>7,7</td><td>9,0</td><td>11</td><td>12</td><td colspan="2">13</td><td>6,6</td><td>7,7</td><td>9,0</td><td>11</td><td>12</td><td>14</td><td colspan="2">17</td><td>20</td><td>23</td><td>26</td><td>29</td></tr>
<tr><td>5</td><td>тет</td><td>200</td><td>3,3</td><td>3,8</td><td>4,5</td><td>5,3</td><td>6,1</td><td>7,1</td><td>8,4</td><td>10</td><td>12</td><td>13</td><td colspan="2">14</td><td>7,3</td><td>8,4</td><td>9,9</td><td>12</td><td>13</td><td>16</td><td colspan="2">18</td><td>21</td><td>25</td><td>29</td><td>31</td></tr>
<tr><td>6</td><td></td><td>250</td><td>4,2</td><td>4,7</td><td>5,4</td><td>6,0</td><td>6,6</td><td>7,6</td><td>8,6</td><td>11</td><td>13</td><td>14</td><td colspan="2">15</td><td>9,2</td><td>10</td><td>12</td><td>13</td><td>15</td><td>17</td><td colspan="2">19</td><td>23</td><td>26</td><td>31</td><td>33</td></tr>
<tr><td></td><td colspan="2">Число рабочих ходов</td><td colspan="12">1</td><td colspan="12">2</td></tr>
<tr><td>7</td><td>Rz 40</td><td>50</td><td>5,4</td><td>6,1</td><td>6,8</td><td>7,8</td><td>8,8</td><td>9,8</td><td>11</td><td>12</td><td>13</td><td>14</td><td colspan="2">15</td><td>7,7</td><td>8,9</td><td>10</td><td>11</td><td>13</td><td>15</td><td colspan="2">17</td><td>19</td><td>22</td><td>23</td><td>25</td></tr>
<tr><td>8</td><td>...</td><td>75</td><td>5,8</td><td>6,6</td><td>7,5</td><td>8,6</td><td>9,8</td><td>11</td><td>13</td><td>14</td><td>16</td><td>17</td><td colspan="2">18</td><td>8,4</td><td>9,7</td><td>11</td><td>13</td><td>15</td><td>17</td><td colspan="2">19</td><td>22</td><td>25</td><td>28</td><td>31</td></tr>
<tr><td>9</td><td>Rz 20,</td><td>110</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td><td>11</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td colspan="2">22</td><td>10</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td><td colspan="2">23</td><td>26</td><td>29</td><td>32</td><td>35</td></tr>
<tr><td>10</td><td>9 ква-</td><td>150</td><td>7,6</td><td>8,6</td><td>9,7</td><td>11</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>22</td><td colspan="2">24</td><td>11</td><td>12</td><td>14</td><td>16</td><td>18</td><td>22</td><td colspan="2">24</td><td>28</td><td>32</td><td>35</td><td>38</td></tr>
<tr><td>11</td><td>литет</td><td>200</td><td>8,7</td><td>9,6</td><td>11</td><td>12</td><td>13</td><td>15</td><td>17</td><td>19</td><td>22</td><td>25</td><td colspan="2">28</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>23</td><td colspan="2">27</td><td>31</td><td>35</td><td>38</td><td>42</td></tr>
<tr><td>12</td><td></td><td>250</td><td>11</td><td>12</td><td>13</td><td>14</td><td>15</td><td>17</td><td>20</td><td>23</td><td>26</td><td>28</td><td colspan="2">30</td><td>15</td><td>16</td><td>18</td><td>20</td><td>22</td><td>26</td><td colspan="2">30</td><td>34</td><td>38</td><td>42</td><td>47</td></tr>
<tr><td></td><td colspan="2">Число рабочих ходов</td><td colspan="12">2</td><td colspan="12">3</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td colspan="2">т</td><td>у</td><td>ф</td><td>х</td><td>ц</td></tr>
<tr><td colspan="27">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="7">1. Предела прочности обрабатываемого материала</td><td colspan="7">Прочность, сигма , МПа в Коэффициент К пп</td><td colspan="4">до 590 0,9</td><td colspan="4">590...740 1,0</td><td colspan="5">св. 740 1,2</td></tr>
<tr><td colspan="7">2. Мощности привода станка</td><td colspan="7">N, кВт Коэффициент К N</td><td colspan="4">4,5 1,2</td><td colspan="4">7,5 1,1</td><td colspan="5">св. 10 1,0</td></tr>
</table>


<a id="p100356"></a>Примечание: При фрезеровании одновременно нескольких заготовок ширина обрабатываемой поверхности (или длина) и, соответственно, время на обработку определяются с учетом количества деталей, установленных на станке.


<a id="p100357"></a>

<table>
<colgroup><col width="5%"><col width="3%"><col width="12%"><col width="8%"><col width="8%"><col width="12%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="9%"></colgroup>
<tr><td colspan="14">Неполное штучное время Горизонтально- и Медные сплавы НВ = 980...1370 МПа вертикально-фрезерные станки Фрезерование плоскостей</td></tr>
<tr><td colspan="14">Фрезы торцовые из стали Р6М5</td></tr>
<tr><td colspan="14">Карта 8</td></tr>
<tr><td colspan="14">рисунок не приводится</td></tr>
<tr><td colspan="2" rowspan="3">N позиции</td><td rowspan="3">Характер обработки</td><td colspan="2" rowspan="3">Ширина обрабатываемой поверхности, В, мм</td><td rowspan="3">Число рабочих ходов, i</td><td colspan="8">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>100</td><td>150</td><td>200</td><td>300</td><td>400</td><td>600</td><td>800</td><td>1000</td></tr>
<tr><td colspan="8">Время на поверхность, t , мин. нш</td></tr>
<tr><td colspan="2">1</td><td>Rz 80;</td><td colspan="2">50</td><td>1</td><td>1,6</td><td>1,9</td><td>2,2</td><td>2,5</td><td>3,0</td><td>3,5</td><td>3,8</td><td>4,3</td></tr>
<tr><td colspan="2">2</td><td>14...12</td><td colspan="2">75</td><td></td><td>1,7</td><td>2,0</td><td>2,3</td><td>2,7</td><td>3,0</td><td>3,8</td><td>4,2</td><td>4,8</td></tr>
<tr><td colspan="2">3</td><td>квали-</td><td colspan="2">110</td><td></td><td>2,0</td><td>2,3</td><td>2,7</td><td>3,3</td><td>3,8</td><td>4,6</td><td>5,2</td><td>6,9</td></tr>
<tr><td colspan="2">4</td><td>тет</td><td colspan="2">150</td><td></td><td>2,1</td><td>2,5</td><td>2,9</td><td>3,6</td><td>4,2</td><td>5,1</td><td>5,8</td><td>6,7</td></tr>
<tr><td colspan="2">5</td><td></td><td colspan="2">200</td><td></td><td>2,3</td><td>2,7</td><td>3,1</td><td>3,7</td><td>4,4</td><td>5,2</td><td>6,1</td><td>7,0</td></tr>
<tr><td colspan="2">6</td><td></td><td colspan="2">250</td><td></td><td>2,5</td><td>2,9</td><td>3,4</td><td>4,0</td><td>4,5</td><td>5,4</td><td>6,4</td><td>7,7</td></tr>
<tr><td colspan="2">7</td><td>Rz 20;</td><td colspan="2">50</td><td>2</td><td>5,2</td><td>6,0</td><td>6,9</td><td>8,1</td><td>9,0</td><td>10</td><td>11</td><td>13</td></tr>
<tr><td colspan="2">8</td><td>11</td><td colspan="2">75</td><td></td><td>6,0</td><td>7,1</td><td>8,2</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td></tr>
<tr><td colspan="2">9</td><td>квали-</td><td colspan="2">110</td><td></td><td>7,8</td><td>8,7</td><td>9,8</td><td>11</td><td>13</td><td>15</td><td>18</td><td>21</td></tr>
<tr><td colspan="2">10</td><td>тет</td><td colspan="2">150</td><td></td><td>8,4</td><td>9,8</td><td>11</td><td>13</td><td>15</td><td>18</td><td>21</td><td>24</td></tr>
<tr><td colspan="2">11</td><td></td><td colspan="2">200</td><td></td><td>9,4</td><td>11</td><td>12</td><td>14</td><td>16</td><td>19</td><td>22</td><td>26</td></tr>
<tr><td colspan="2">12</td><td></td><td colspan="2">250</td><td></td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td><td>24</td><td>29</td><td>34</td></tr>
<tr><td colspan="5">Индекс</td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
<tr><td colspan="14">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="2">1.</td><td colspan="3" rowspan="2">Твердости обрабатываемого материала</td><td colspan="3">Твердость НВ, МПа</td><td colspan="5">590...980 980... 1370</td><td colspan="2">1370... 2450</td></tr>
<tr><td colspan="3">Коэффициент К тв</td><td colspan="5">0,7 1,0</td><td colspan="2">1,2</td></tr>
<tr><td rowspan="2">2.</td><td colspan="3" rowspan="2">Материала режущего инструмента</td><td colspan="3">Режущий инструмент</td><td colspan="7">Резцы из стали Резцы с плас- Р6М5 тинками ВК8</td></tr>
<tr><td colspan="3">Коэффициент К ри</td><td colspan="7">1,0 0,6</td></tr>
</table>


<a id="p100379"></a>Примечание.
<a id="p100380"></a>При фрезеровании одновременно нескольких заготовок ширина обрабатываемой поверхности (или длина), и соответственно, время на обработку определяется с учетом количества деталей, установленных на станке.


<a id="p100381"></a>

<table>
<colgroup><col width="5%"><col width="8%"><col width="10%"><col width="4%"><col width="6%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="6%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="7">Неполное штучное время Фрезерование плоскостей</td><td colspan="13">Горизонтально- и вертикально-фрезерные станки</td></tr>
<tr><td colspan="7" rowspan="2">Чугун серый, НВ = 1760...2150 МПа</td><td colspan="13">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="13">Карта 9</td></tr>
<tr><td colspan="20">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Характер</td><td>Диаметр фрезы,</td><td colspan="2" rowspan="3">Ширина обрабатываемой поверхности, В, мм</td><td rowspan="2">Число рабочих ходов,</td><td colspan="14">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">обработки</td><td>D, мм, и число</td><td>50</td><td>100</td><td>150</td><td>200</td><td colspan="2">250</td><td>300</td><td>400</td><td>500</td><td colspan="2">600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>зубьев, z</td><td>i</td><td colspan="14">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>16/4</td><td colspan="2">20...30</td><td>1</td><td>1,8</td><td>2,2</td><td>2,5</td><td>2,7</td><td colspan="2">3,4</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>14... 12</td><td>16/3</td><td colspan="2"></td><td rowspan="2"></td><td>2,0</td><td>2,3</td><td>2,6</td><td>2,8</td><td colspan="2">3,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>квалитет</td><td>20/5; 25/5</td><td colspan="2">20...40</td><td>1,9</td><td>2,3</td><td>2,6</td><td>2,8</td><td colspan="2">3,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td rowspan="2"></td><td>20/3; 25/3</td><td colspan="2"></td><td rowspan="2"></td><td>2,2</td><td>2,5</td><td>3,0</td><td>3,5</td><td colspan="2">4,2</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>32/6; 40/6; 50/6</td><td colspan="2">20...60</td><td>2,3</td><td>2,7</td><td>3,2</td><td>3,7</td><td colspan="2">4,5</td><td>4,8</td><td>5,6</td><td>6,7</td><td colspan="2">7,6</td><td>9,0</td><td>10</td><td>13</td></tr>
<tr><td>6</td><td></td><td>32/4; 40/4; 50/4</td><td colspan="2"></td><td></td><td>2,4</td><td>3,2</td><td>3,8</td><td>4,4</td><td colspan="2">5,0</td><td>5,8</td><td>6,7</td><td>8,0</td><td colspan="2">9,0</td><td>11</td><td>12</td><td>15</td></tr>
<tr><td>7</td><td>Rz 20;</td><td>16/4</td><td colspan="2">20...30</td><td>2</td><td>4,2</td><td>5,0</td><td>5,6</td><td>6,4</td><td colspan="2">7,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td rowspan="2">9 квалитет</td><td>16/3</td><td colspan="2"></td><td rowspan="2"></td><td>4,5</td><td>5,5</td><td>6,0</td><td>7,0</td><td colspan="2">8,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>20/5; 25/5</td><td colspan="2">20...40</td><td>4,4</td><td>5,1</td><td>5,7</td><td>6,6</td><td colspan="2">8,0</td><td>9,0</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td rowspan="2"></td><td>20/3; 25/3</td><td colspan="2"></td><td rowspan="2"></td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td colspan="2">9,0</td><td>10,5</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td>32/6; 40/6</td><td colspan="2">20...60</td><td>4,9</td><td>5,4</td><td>6,0</td><td>7,0</td><td colspan="2">8,2</td><td>8,8</td><td>10</td><td>12</td><td colspan="2">14</td><td>16</td><td>18</td><td>20</td></tr>
<tr><td>12</td><td rowspan="2"></td><td>32/4; 40/4</td><td colspan="2"></td><td rowspan="2"></td><td>5,5</td><td>6,2</td><td>7,3</td><td>8,4</td><td colspan="2">9,5</td><td>11</td><td>12</td><td>14</td><td colspan="2">16</td><td>19</td><td>21</td><td>25</td></tr>
<tr><td>13</td><td>50/6</td><td colspan="2">20...60</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td>9,2</td><td>11</td><td>13</td><td colspan="2">15</td><td>17</td><td>19</td><td>22</td></tr>
<tr><td>14</td><td></td><td>50/4</td><td colspan="2"></td><td></td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,6</td><td colspan="2">10</td><td>12</td><td>13</td><td>15</td><td colspan="2">18</td><td>20</td><td>22</td><td>26</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td></tr>
<tr><td colspan="20">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="2">1.</td><td colspan="3">Твердости обрабатываемого</td><td colspan="7">Твердость, НВ, МПа</td><td colspan="5">до 2150</td><td colspan="4">св. 2150</td></tr>
<tr><td colspan="3">материала</td><td colspan="7">Коэффициент К тв</td><td colspan="5">1,0</td><td colspan="4">1,2</td></tr>
<tr><td rowspan="2">2.</td><td colspan="3" rowspan="2">Формы обрабатываемой поверхности</td><td colspan="7">Поверхность</td><td colspan="5">прямолинейная</td><td colspan="4">криволинейная (фасонная)</td></tr>
<tr><td colspan="7">Коэффициент К фн</td><td colspan="5">1,0</td><td colspan="4">1,2</td></tr>
</table>



<a id="p100403"></a>

<table>
<colgroup><col width="5%"><col width="11%"><col width="9%"><col width="5%"><col width="4%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="8" rowspan="3">Неполное штучное время Фрезерование уступов, Rz 40...Rz 20 Чугун серый, НВ = 1760...2150 МПа</td><td colspan="10">Горизонтально- и вертикально-фрезерные станки</td></tr>
<tr><td colspan="10">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="10">Карта 10</td></tr>
<tr><td colspan="18">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фрезы,</td><td rowspan="2">Ширина фрезерования В,</td><td colspan="2" rowspan="2">Глубина резания, t, мм,</td><td colspan="13">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>D, мм, и число</td><td>50</td><td>100</td><td colspan="2">150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>зубьев, z</td><td>мм, до</td><td colspan="2">до</td><td colspan="13">Время на проход, t , мин. нш</td></tr>
<tr><td>1</td><td>16/4</td><td>18</td><td colspan="2">5</td><td>2,4</td><td>3,0</td><td colspan="2">3,2</td><td>3,5</td><td>4,0</td><td>4,5</td><td>5,0</td><td>6,0</td><td>6,7</td><td>8,0</td><td>8,5</td><td>9,0</td></tr>
<tr><td>2</td><td>20/5</td><td></td><td colspan="2">10</td><td>2,5</td><td>3,1</td><td colspan="2">3,5</td><td>4,0</td><td>4,5</td><td>5,0</td><td>5,7</td><td>7,0</td><td>8,0</td><td>9,0</td><td>9,5</td><td>11</td></tr>
<tr><td>3</td><td></td><td></td><td colspan="2">20</td><td>2,6</td><td>3,2</td><td colspan="2">3,8</td><td>4,5</td><td>5,5</td><td>6,0</td><td>6,7</td><td>8,2</td><td>9,0</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>4</td><td>25/5</td><td></td><td colspan="2">30</td><td>3,0</td><td>3,5</td><td colspan="2">4,0</td><td>5,0</td><td>6,0</td><td>6,6</td><td>8,0</td><td>9,0</td><td>11</td><td>12</td><td>14</td><td>16</td></tr>
<tr><td>5</td><td></td><td></td><td colspan="2">40</td><td>3,1</td><td>4,0</td><td colspan="2">4,7</td><td>5,7</td><td>7,0</td><td>8,0</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>17</td><td>19</td></tr>
<tr><td>6</td><td>25/5</td><td>22</td><td colspan="2">10</td><td>2,6</td><td>3,2</td><td colspan="2">4,0</td><td>4,5</td><td>5,0</td><td>5,6</td><td>6,8</td><td>8,0</td><td>9,0</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>7</td><td></td><td></td><td colspan="2">20</td><td>2,7</td><td>3,3</td><td colspan="2">4,1</td><td>4,6</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,1</td><td>9,5</td><td>12</td><td>13</td><td>15</td></tr>
<tr><td>8</td><td></td><td></td><td colspan="2">30</td><td>3,0</td><td>4,0</td><td colspan="2">5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>9</td><td></td><td></td><td colspan="2">45</td><td>3,5</td><td>4,5</td><td colspan="2">5,6</td><td>6,7</td><td>8,5</td><td>9,0</td><td>11</td><td>14</td><td>16</td><td>18</td><td>20</td><td>23</td></tr>
<tr><td>10</td><td>32/6</td><td>25</td><td colspan="2">10</td><td>2,5</td><td>3,0</td><td colspan="2">3,5</td><td>4,0</td><td>4,7</td><td>5,0</td><td>5,7</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td><td>12</td></tr>
<tr><td>11</td><td>40/6</td><td></td><td colspan="2">20</td><td>2,6</td><td>3,4</td><td colspan="2">4,0</td><td>4,5</td><td>5,4</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td><td>11</td><td>14</td></tr>
<tr><td>12</td><td></td><td></td><td colspan="2">30</td><td>3,0</td><td>3,6</td><td colspan="2">4,4</td><td>5,0</td><td>6,0</td><td>6,7</td><td>8,0</td><td>9,6</td><td>11</td><td>12</td><td>13</td><td>16</td></tr>
<tr><td>13</td><td>50/6</td><td></td><td colspan="2">40</td><td>3,2</td><td>4,0</td><td colspan="2">5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>14</td><td></td><td></td><td colspan="2">60</td><td>3,5</td><td>4,7</td><td colspan="2">5,7</td><td>7,0</td><td>8,5</td><td>9,0</td><td>11</td><td>14</td><td>16</td><td>18</td><td>20</td><td>23</td></tr>
<tr><td>15</td><td>50/6</td><td>30</td><td colspan="2">10</td><td>2,6</td><td>3,2</td><td colspan="2">3,6</td><td>4,2</td><td>4,8</td><td>5,5</td><td>6,0</td><td>7,2</td><td>8,2</td><td>9,0</td><td>10</td><td>11</td></tr>
<tr><td>16</td><td></td><td></td><td colspan="2">20</td><td>3,2</td><td>3,8</td><td colspan="2">4,5</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11</td><td>12</td><td>13</td><td>16</td></tr>
<tr><td>17</td><td></td><td></td><td colspan="2">30</td><td>3,5</td><td>4,5</td><td colspan="2">5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10</td><td>13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>18</td><td></td><td></td><td colspan="2">40</td><td>4,0</td><td>5,0</td><td colspan="2">6,0</td><td>7,5</td><td>8,6</td><td>9,5</td><td>11</td><td>14</td><td>17</td><td>19</td><td>21</td><td>24</td></tr>
<tr><td>19</td><td></td><td></td><td colspan="2">60</td><td>4,5</td><td>5,7</td><td colspan="2">7,5</td><td>8,6</td><td>10</td><td>12</td><td>14</td><td>17</td><td>19</td><td>22</td><td>24</td><td>29</td></tr>
<tr><td>20</td><td>50/6</td><td>45</td><td colspan="2">10</td><td>3,0</td><td>3,5</td><td colspan="2">4,0</td><td>4,7</td><td>5,6</td><td>6,0</td><td>7,0</td><td>8,5</td><td>9,5</td><td>10</td><td>12</td><td>14</td></tr>
<tr><td>21</td><td></td><td></td><td colspan="2">20</td><td>3,2</td><td>4,0</td><td colspan="2">4,5</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td>10</td><td>12</td><td>13</td><td>16</td></tr>
<tr><td>22</td><td></td><td></td><td colspan="2">30</td><td>4,0</td><td>5,0</td><td colspan="2">6,0</td><td>7,5</td><td>9,0</td><td>9,5</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>23</td></tr>
<tr><td>23</td><td></td><td></td><td colspan="2">40</td><td>4,5</td><td>6,0</td><td colspan="2">7,5</td><td>8,6</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>22</td><td>25</td></tr>
<tr><td>24</td><td></td><td></td><td colspan="2">60</td><td>5,0</td><td>6,7</td><td colspan="2">8,6</td><td>10</td><td>12</td><td>14</td><td>17</td><td>21</td><td>25</td><td>29</td><td>33</td><td>38</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
<tr><td colspan="18">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">1. Твердости обрабатываемого материала</td><td colspan="6">Твердость, НВ, МПа Коэффициент К тв</td><td colspan="6">до 2150 1,0</td><td colspan="2">св. 2150 1,2</td></tr>
<tr><td colspan="4">2. Формы обрабатываемой поверхности</td><td colspan="6">Поверхность Коэффициент К ф</td><td colspan="4">прямолинейная 1,0</td><td colspan="4">криволинейная 1,2</td></tr>
</table>


<a id="p100435"></a>Примечание: Карта рассчитана на фрезерование уступов типа А. При фрезеровании уступов типа Б неполное штучное время следует принимать с коэффициентом К = 0,85.


<a id="p100436"></a>

<table>
<colgroup><col width="4%"><col width="9%"><col width="4%"><col width="5%"><col width="5%"><col width="6%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"></colgroup>
<tr><td colspan="22">Неполное штучное время Горизонтально- и вертикально-фрезерные станки Фрезерование Т-образных пазов, Rz 40...Rz 20; 11 квалитет</td></tr>
<tr><td colspan="22">Чугун серый, НВ = 1760...2150 МПа Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="22">Карта 11</td></tr>
<tr><td colspan="22">рисунок не приводится</td></tr>
<tr><td rowspan="7">N позиции</td><td rowspan="7">Длина Т-образного паза, l, мм, до</td><td colspan="20">Ширина Т-образного паза, В , мм, до 1</td></tr>
<tr><td colspan="2">16</td><td colspan="2">19</td><td colspan="2">23</td><td colspan="2">30</td><td colspan="2">37</td><td colspan="2">46</td><td colspan="2">56</td><td colspan="2">68</td><td colspan="2">80</td><td colspan="2">90</td></tr>
<tr><td colspan="20">Ширина прямоугольного паза, В, мм, до</td></tr>
<tr><td colspan="2">10</td><td colspan="2">12</td><td colspan="2">14</td><td colspan="2">18</td><td colspan="2">22</td><td colspan="2">28</td><td colspan="2">36</td><td colspan="2">42</td><td colspan="2">48</td><td colspan="2">54</td></tr>
<tr><td colspan="20">Глубина прямоугольного паза, Н, мм, до</td></tr>
<tr><td colspan="2">17 21</td><td colspan="2">20 25</td><td colspan="2">23 28</td><td colspan="2">30 36</td><td colspan="2">38 45</td><td colspan="2">48 56</td><td colspan="2">61 71</td><td colspan="2">74 85</td><td colspan="2">84 95</td><td colspan="2">94 106</td></tr>
<tr><td colspan="20">Время на один паз, t , мин. нш</td></tr>
<tr><td>1</td><td>25</td><td colspan="2">3,2 4,0</td><td colspan="2">3,6 4,2</td><td colspan="2">3,8 4,5</td><td colspan="2">4,0 4,8</td><td colspan="2">5,0 5,5</td><td colspan="2">6,0 6,5</td><td colspan="2">6,8 7,7</td><td colspan="2">7,3 8,2</td><td colspan="2">10 14</td><td colspan="2">12 16</td></tr>
<tr><td>2</td><td>50</td><td colspan="2">4,6 6,0</td><td colspan="2">5,0 6,2</td><td colspan="2">5,2 6,5</td><td colspan="2">5,5 6,5</td><td colspan="2">7,0 7,6</td><td colspan="2">8,0 8,7</td><td colspan="2">10 11</td><td colspan="2">11 12</td><td colspan="2">15 22</td><td colspan="2">16 24</td></tr>
<tr><td>3</td><td>100</td><td colspan="2">6,5 8,0</td><td colspan="2">6,8 8,5</td><td colspan="2">7,0 8,0</td><td colspan="2">7,5 8,7</td><td colspan="2">9,0 10</td><td colspan="2">10 11</td><td colspan="2">14 15</td><td colspan="2">15 16</td><td colspan="2">21 29</td><td colspan="2">23 31</td></tr>
<tr><td>4</td><td>150</td><td colspan="2">8,0 9,5</td><td colspan="2">8,2 10</td><td colspan="2">8,4 11</td><td colspan="2">8,6 11</td><td colspan="2">12 13</td><td colspan="2">13 14</td><td colspan="2">16 21</td><td colspan="2">18 20</td><td colspan="2">25 36</td><td colspan="2">28 39</td></tr>
<tr><td>5</td><td>200</td><td colspan="2">10 11</td><td colspan="2">10,5 11,5</td><td colspan="2">11 12</td><td colspan="2">12 13</td><td colspan="2">13 14</td><td colspan="2">15 16</td><td colspan="2">20 23</td><td colspan="2">22 25</td><td colspan="2">31 44</td><td colspan="2">34 46</td></tr>
<tr><td>6</td><td>250</td><td colspan="2">12 14</td><td colspan="2">13 15</td><td colspan="2">14 14</td><td colspan="2">15 17</td><td colspan="2">16 18</td><td colspan="2">18 20</td><td colspan="2">25 27</td><td colspan="2">26 29</td><td colspan="2">36 51</td><td colspan="2">40 55</td></tr>
<tr><td>7</td><td>300</td><td colspan="2">14 16</td><td colspan="2">15 17</td><td colspan="2">16 17</td><td colspan="2">17 19</td><td colspan="2">20 21</td><td colspan="2">20 34</td><td colspan="2">27 32</td><td colspan="2">29 34</td><td colspan="2">42 60</td><td colspan="2">46 64</td></tr>
<tr><td>8</td><td>400</td><td colspan="2">17 19</td><td colspan="2">18 20</td><td colspan="2">19 21</td><td colspan="2">20 22</td><td colspan="2">22 24</td><td colspan="2">25 29</td><td colspan="2">34 39</td><td colspan="2">36 42</td><td colspan="2">52 72</td><td colspan="2">56 75</td></tr>
<tr><td>9</td><td>500</td><td colspan="2">19 23</td><td colspan="2">20 24</td><td colspan="2">21 25</td><td colspan="2">22 26</td><td colspan="2">28 30</td><td colspan="2">30 35</td><td colspan="2">41 45</td><td colspan="2">45 48</td><td colspan="2">64 90</td><td colspan="2">69 95</td></tr>
<tr><td>10</td><td>600</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">23 30</td><td colspan="2">33 35</td><td colspan="2">35 40</td><td colspan="2">47 55</td><td colspan="2">51 59</td><td colspan="2">74 102</td><td colspan="2">79 107</td></tr>
<tr><td>11</td><td>700</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">25 33</td><td colspan="2">35 38</td><td colspan="2">39 45</td><td colspan="2">54 64</td><td colspan="2">58 68</td><td colspan="2">84 112</td><td colspan="2">91 118</td></tr>
<tr><td>12</td><td>800</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">29 38</td><td colspan="2">41 44</td><td colspan="2">43 50</td><td colspan="2">61 71</td><td colspan="2">66 76</td><td colspan="2">93 118</td><td colspan="2">101 128</td></tr>
<tr><td>13</td><td>1000</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">32 42</td><td colspan="2">46 48</td><td colspan="2">46 57</td><td colspan="2">68 77</td><td colspan="2">74 83</td><td colspan="2">104 127</td><td colspan="2">112 136</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td>у</td><td>ф</td></tr>
<tr><td colspan="22">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="10">Твердости Твердость, НВ, МПа обрабатываемого Коэффициент К материала тв</td><td colspan="12">до 2150 св. 2150 1,0 1,2</td></tr>
</table>



<a id="p100460"></a>

<table>
<colgroup><col width="5%"><col width="7%"><col width="9%"><col width="9%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="18">Неполное штучное время Горизонтально- и вертикально- Фрезерование пазов типа "Ласточкин хвост", фрезерные станки Rz 40...Rz 20</td></tr>
<tr><td colspan="18">Чугун серый, НВ = 1760...2150 МПа Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="18">Карта 12</td></tr>
<tr><td colspan="18">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Глубина</td><td>Диаметр фрезы,</td><td>Угол, фи,</td><td rowspan="2">Число рабочих ходов,</td><td colspan="13">Длина обрабатываемого паза, l, мм, до</td></tr>
<tr><td rowspan="2">паза, Н, мм</td><td>D, мм, и число</td><td rowspan="2">градусы</td><td>25</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>зубьев, z</td><td>i</td><td colspan="13">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>6</td><td>10 -- 8</td><td>70...80</td><td rowspan="2">2</td><td>4,2</td><td>4,7</td><td>5,2</td><td>5,6</td><td>6,0</td><td>7,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10</td><td>12</td><td>13</td><td>15</td></tr>
<tr><td>2</td><td>8</td><td>16</td><td>70...80</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,6</td><td>7,8</td><td>8,2</td><td>9,5</td><td>11</td><td>12</td><td>14</td><td>15</td><td>17</td></tr>
<tr><td>3</td><td></td><td>-- 10</td><td>60...65</td><td rowspan="2"></td><td>4,6</td><td>5,2</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td><td>12</td><td>14</td><td>16</td><td>17</td><td>19</td></tr>
<tr><td>4</td><td>10</td><td>25</td><td>75...80</td><td>4,3</td><td>4,8</td><td>5,4</td><td>5,8</td><td>6,0</td><td>7,0</td><td>7,5</td><td>8,4</td><td>10</td><td>11</td><td>12</td><td>13</td><td>15</td></tr>
<tr><td>5</td><td></td><td>--</td><td>65...70</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td></tr>
<tr><td>6</td><td></td><td>12</td><td>55...60</td><td></td><td>4,6</td><td>5,3</td><td>6,2</td><td>6,6</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>18</td><td>20</td></tr>
<tr><td></td><td></td><td></td><td></td><td></td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td><td>12</td><td>14</td><td>16</td><td>19</td><td>21</td><td>24</td><td>28</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
<tr><td colspan="18">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Твердости обрабатываемого материала</td><td colspan="14">Твердость, НВ, МПа до 2150 св. 2150 Коэффициент К 1,0 1,12 тв</td></tr>
</table>



<a id="p100473"></a>

<table>
<colgroup><col width="5%"><col width="8%"><col width="7%"><col width="8%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="20">Неполное штучное время Горизонтально- и вертикально- Фрезерование пазов, Rz 40...Rz 20; 11 квалитет фрезерные станки Чугун серый, НВ = 1760...2150 МПа</td></tr>
<tr><td colspan="20">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="20">Карта 13</td></tr>
<tr><td colspan="20">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Режущий</td><td>Ширина</td><td rowspan="3">Глубина паза, Н, мм</td><td rowspan="3">Число рабочих ходов, i</td><td colspan="15">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">инструмент</td><td rowspan="2">паза, В, мм</td><td>25</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td colspan="2">500</td><td colspan="2">600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td colspan="15">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>Фрезы</td><td>6</td><td>3</td><td>1</td><td>1,7</td><td>1,9</td><td>2,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>концевые из</td><td></td><td>5</td><td rowspan="4"></td><td>1,9</td><td>2,1</td><td>2,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td rowspan="3">стали Р6М5</td><td>10</td><td>12</td><td>2,0</td><td>2,3</td><td>3,4</td><td>4,3</td><td>5,2</td><td>6,5</td><td>7,5</td><td>9,5</td><td colspan="2">11</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>16</td><td>20</td><td>2,2</td><td>2,6</td><td>3,6</td><td>4,4</td><td>5,5</td><td>6,8</td><td>7,8</td><td>9,8</td><td colspan="2">10</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>25</td><td>16</td><td>1,6</td><td>1,8</td><td>2,1</td><td>2,4</td><td>3,0</td><td>3,6</td><td>4,3</td><td>5,0</td><td colspan="2">6,0</td><td colspan="2">6,8</td><td>7,7</td><td>8,5</td><td>9,3</td></tr>
<tr><td>6</td><td></td><td></td><td>20</td><td></td><td>1,9</td><td>2,1</td><td>2,9</td><td>3,8</td><td>4,3</td><td>5,4</td><td>6,0</td><td>7,6</td><td colspan="2">9,2</td><td colspan="2">10</td><td>11</td><td>13</td><td>15</td></tr>
<tr><td>7</td><td rowspan="2"></td><td></td><td>30</td><td rowspan="2"></td><td>2,1</td><td>2,5</td><td>3,2</td><td>4,0</td><td>4,9</td><td>5,8</td><td>6,6</td><td>8,3</td><td colspan="2">9,8</td><td colspan="2">11</td><td>13</td><td>15</td><td>16</td></tr>
<tr><td>8</td><td>32</td><td>20</td><td>2,0</td><td>2,5</td><td>3,5</td><td>4,0</td><td>4,5</td><td>5,5</td><td>6,0</td><td>7,5</td><td colspan="2">9,0</td><td colspan="2">10</td><td>12</td><td>13</td><td>15</td></tr>
<tr><td>9</td><td rowspan="2"></td><td></td><td>30</td><td></td><td>2,5</td><td>3,0</td><td>4,0</td><td>4,5</td><td>5,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td colspan="2">11</td><td colspan="2">13</td><td>15</td><td>17</td><td>21</td></tr>
<tr><td>10</td><td>40</td><td>30</td><td>2</td><td>5,0</td><td>7,0</td><td>9,0</td><td>11</td><td>13</td><td>16</td><td>18</td><td>22</td><td colspan="2">27</td><td colspan="2">31</td><td>35</td><td>40</td><td>50</td></tr>
<tr><td>11</td><td rowspan="2"></td><td></td><td>40</td><td rowspan="2"></td><td>5,5</td><td>8,0</td><td>10</td><td>13</td><td>16</td><td>19</td><td>22</td><td>27</td><td colspan="2">32</td><td colspan="2">38</td><td>45</td><td>52</td><td>64</td></tr>
<tr><td>12</td><td>50</td><td>30</td><td>6,0</td><td>8,5</td><td>11</td><td>14</td><td>17</td><td>20</td><td>23</td><td>28</td><td colspan="2">33</td><td colspan="2">39</td><td>46</td><td>53</td><td>65</td></tr>
<tr><td>13</td><td></td><td></td><td>40</td><td></td><td>6,5</td><td>9,5</td><td>13</td><td>16</td><td>20</td><td>24</td><td>27</td><td>34</td><td colspan="2">43</td><td colspan="2">50</td><td>56</td><td>62</td><td>70</td></tr>
<tr><td>14</td><td>Фрезы</td><td>10</td><td>8</td><td>1</td><td>1,5</td><td>1,6</td><td>2,0</td><td>2,1</td><td>2,3</td><td>2,8</td><td>3,0</td><td>3,5</td><td colspan="2">4,2</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>концевые с</td><td></td><td>12</td><td rowspan="2"></td><td>1,6</td><td>1,8</td><td>2,1</td><td>2,4</td><td>2,7</td><td>3,3</td><td>3,5</td><td>4,3</td><td colspan="2">5,0</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>плас-</td><td>16</td><td>16</td><td>1,7</td><td>1,9</td><td>2,4</td><td>2,7</td><td>3,2</td><td>3,6</td><td>3,8</td><td>5,0</td><td colspan="2">6,0</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td rowspan="2">тинками ВК8</td><td></td><td>20</td><td rowspan="2"></td><td>1,8</td><td>2,3</td><td>3,2</td><td>3,9</td><td>4,7</td><td>5,4</td><td>6,2</td><td>8,0</td><td colspan="2">9,0</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td>25</td><td>16</td><td>1,5</td><td>1,6</td><td>1,8</td><td>2,2</td><td>2,5</td><td>3,0</td><td>3,5</td><td>4,0</td><td colspan="2">4,5</td><td colspan="2">5,0</td><td>6,0</td><td>6,5</td><td>8,0</td></tr>
<tr><td>19</td><td></td><td></td><td>20</td><td></td><td>1,6</td><td>1,8</td><td>2,2</td><td>2,5</td><td>3,0</td><td>3,5</td><td>4,0</td><td>4,5</td><td colspan="2">5,5</td><td colspan="2">6,0</td><td>6,6</td><td>7,0</td><td>8,5</td></tr>
<tr><td>20</td><td rowspan="2"></td><td></td><td>30</td><td rowspan="2"></td><td>1,8</td><td>2,0</td><td>2,5</td><td>3,0</td><td>3,5</td><td>4,5</td><td>5,0</td><td>5,5</td><td colspan="2">7,0</td><td colspan="2">8,0</td><td>9,0</td><td>10</td><td>12</td></tr>
<tr><td>21</td><td>32</td><td>20</td><td>2,0</td><td>2,4</td><td>3,2</td><td>3,8</td><td>4,6</td><td>5,5</td><td>6,2</td><td>7,5</td><td colspan="2">9,0</td><td colspan="2">10</td><td>11</td><td>13</td><td>15</td></tr>
<tr><td>22</td><td rowspan="2"></td><td></td><td>30</td><td></td><td>2,3</td><td>2,8</td><td>3,6</td><td>4,6</td><td>5,5</td><td>6,5</td><td>7,3</td><td>9,0</td><td colspan="2">11</td><td colspan="2">13</td><td>14</td><td>16</td><td>18</td></tr>
<tr><td>23</td><td>40</td><td>30</td><td>2</td><td>3,6</td><td>5,0</td><td>6,5</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td colspan="2">18</td><td colspan="2">21</td><td>24</td><td>27</td><td>32</td></tr>
<tr><td>24</td><td rowspan="2"></td><td></td><td>40</td><td rowspan="2"></td><td>4,0</td><td>6,0</td><td>7,5</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>18</td><td colspan="2">22</td><td colspan="2">26</td><td>29</td><td>33</td><td>40</td></tr>
<tr><td>25</td><td>50</td><td>30</td><td>4,5</td><td>6,0</td><td>8,0</td><td>10</td><td>12</td><td>14</td><td>16</td><td>19</td><td colspan="2">23</td><td colspan="2">27</td><td>30</td><td>34</td><td>41</td></tr>
<tr><td>26</td><td></td><td></td><td>40</td><td></td><td>5,0</td><td>7,0</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>18</td><td>23</td><td colspan="2">27</td><td colspan="2">31</td><td>36</td><td>40</td><td>47</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
<tr><td colspan="20">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="9">1. Твердости обрабатыва- Твердость, НВ, МПа емого материала Коэффициент К тв</td><td colspan="7">до 2150 1,0</td><td colspan="4">св. 2150 1,2</td></tr>
<tr><td colspan="9">2. Формы обрабатываемой Поверхность поверхности Коэффициент К ф</td><td colspan="5">Прямолинейная 1,0</td><td colspan="6">Криволинейная (фасонная) 1,2</td></tr>
</table>



<a id="p100507"></a>

<table>
<colgroup><col width="5%"><col width="8%"><col width="7%"><col width="8%"><col width="9%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="10" rowspan="3">Неполное штучное время Фрезерование плоскостей Сталь конструкционная, сигма = 590...740 МПа в</td><td colspan="9">Горизонтально- и вертикальнофрезерные станки</td></tr>
<tr><td colspan="9">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="9">Карта 14</td></tr>
<tr><td colspan="19">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Характер</td><td rowspan="3">Вид заготовки</td><td>Диаметр</td><td rowspan="3">Ширина обработки, В, мм</td><td rowspan="3">Число рабочих ходов, i</td><td colspan="13">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">обработки</td><td>фрезы, D, и</td><td>50</td><td>100</td><td>150</td><td colspan="2">200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>число зубьев, z</td><td colspan="13">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>Про-</td><td>16/4</td><td>20...30</td><td>1</td><td>1,8</td><td>2,0</td><td>2,4</td><td colspan="2">2,6</td><td>3,4</td><td>3,5</td><td>4,2</td><td>5,0</td><td>5,6</td><td>6,7</td><td>7,3</td><td>8,5</td></tr>
<tr><td>2</td><td>14... 12</td><td rowspan="2">кат</td><td>16/3</td><td></td><td rowspan="2"></td><td>1,9</td><td>2,3</td><td>2,5</td><td colspan="2">2,8</td><td>3,5</td><td>4,0</td><td>4,7</td><td>5,7</td><td>6,5</td><td>7,6</td><td>8,4</td><td>9,5</td></tr>
<tr><td>3</td><td>квали-</td><td>20/5</td><td>20...60</td><td>1,9</td><td>2,4</td><td>2,6</td><td colspan="2">3,0</td><td>3,6</td><td>4,2</td><td>4,8</td><td>5,8</td><td>6,7</td><td>7,8</td><td>8,6</td><td>10</td></tr>
<tr><td>4</td><td rowspan="2">тет</td><td rowspan="2"></td><td>20/3</td><td></td><td rowspan="2"></td><td>2,0</td><td>2,5</td><td>3,0</td><td colspan="2">3,5</td><td>4,2</td><td>4,7</td><td>5,6</td><td>7,0</td><td>7,8</td><td>8,5</td><td>10</td><td>12</td></tr>
<tr><td>5</td><td>50/6</td><td>20...60</td><td>2,2</td><td>2,6</td><td>3,2</td><td colspan="2">3,7</td><td>4,4</td><td>5,0</td><td>5,8</td><td>7,0</td><td>8,0</td><td>9,0</td><td>11</td><td>13</td></tr>
<tr><td>6</td><td></td><td></td><td>50/4</td><td></td><td></td><td>2,3</td><td>2,8</td><td>3,5</td><td colspan="2">4,0</td><td>4,8</td><td>5,5</td><td>6,5</td><td>8,0</td><td>9,0</td><td>11</td><td>13</td><td>15</td></tr>
<tr><td>7</td><td>Rz 20;</td><td></td><td>16/4</td><td>20...30</td><td>2</td><td>3,4</td><td>4,5</td><td>5,0</td><td colspan="2">5,6</td><td>6,5</td><td>7,5</td><td>8,0</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td></tr>
<tr><td>8</td><td rowspan="2">9 квалитет</td><td rowspan="2"></td><td>16/3</td><td></td><td rowspan="2"></td><td>4,0</td><td>4,8</td><td>5,4</td><td colspan="2">6,2</td><td>7,5</td><td>8,5</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>21</td></tr>
<tr><td>9</td><td>20/5</td><td>20...60</td><td>4,2</td><td>5,0</td><td>5,5</td><td colspan="2">6,6</td><td>7,8</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>17</td><td>19</td><td>22</td></tr>
<tr><td>10</td><td rowspan="2"></td><td rowspan="2"></td><td>20/3</td><td></td><td rowspan="2"></td><td>4,5</td><td>5,5</td><td>6,0</td><td colspan="2">7,0</td><td>8,5</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>23</td></tr>
<tr><td>11</td><td>50/6</td><td>20...60</td><td>4,8</td><td>5,8</td><td>6,5</td><td colspan="2">7,5</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>17</td><td>19</td><td>21</td><td>24</td></tr>
<tr><td>12</td><td></td><td></td><td>50/4</td><td></td><td></td><td>5,0</td><td>6,0</td><td>7,0</td><td colspan="2">8,0</td><td>9,5</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>22</td><td>25</td></tr>
<tr><td>13</td><td>Rz 80;</td><td>По-</td><td>16/4</td><td>20...30</td><td>2</td><td>3,5</td><td>4,2</td><td>4,5</td><td colspan="2">5,0</td><td>6,0</td><td>7,0</td><td>7,5</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>18</td></tr>
<tr><td>14</td><td>14... 12</td><td>ковка или</td><td>16/3</td><td></td><td rowspan="2"></td><td>3,8</td><td>4,4</td><td>4,8</td><td colspan="2">5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td></tr>
<tr><td>15</td><td>квали-</td><td>отли-</td><td>20/5</td><td>20...60</td><td>4,0</td><td>4,5</td><td>5,0</td><td colspan="2">6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>17</td><td>21</td></tr>
<tr><td>16</td><td rowspan="2">тет</td><td rowspan="2">вка</td><td>20/3</td><td></td><td rowspan="2"></td><td>4,5</td><td>5,0</td><td>5,5</td><td colspan="2">6,5</td><td>7,5</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>17</td><td>19</td><td>23</td></tr>
<tr><td>17</td><td>50/6</td><td>20...60</td><td>5,0</td><td>5,5</td><td>6,0</td><td colspan="2">7,0</td><td>8,0</td><td>9,5</td><td>12</td><td>14</td><td>16</td><td>18</td><td>21</td><td>24</td></tr>
<tr><td>18</td><td></td><td rowspan="2"></td><td>50/4</td><td></td><td></td><td>5,5</td><td>6,0</td><td>7,0</td><td colspan="2">8,0</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td><td>22</td><td>26</td></tr>
<tr><td>19</td><td>Rz 20;</td><td>16/4</td><td>20...30</td><td>3</td><td>6,4</td><td>7,0</td><td>7,8</td><td colspan="2">8,5</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>19</td><td>22</td><td>26</td></tr>
<tr><td>20</td><td rowspan="2">9 квалитет</td><td rowspan="2"></td><td>16/3</td><td></td><td rowspan="2"></td><td>6,5</td><td>7,5</td><td>8,3</td><td colspan="2">9,0</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>23</td><td>27</td></tr>
<tr><td>21</td><td>20/5</td><td>20...60</td><td>6,6</td><td>7,8</td><td>8,5</td><td colspan="2">9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>19</td><td>21</td><td>25</td><td>29</td></tr>
<tr><td>22</td><td rowspan="2"></td><td rowspan="2"></td><td>20/3</td><td></td><td rowspan="2"></td><td>6,7</td><td>8,0</td><td>9,0</td><td colspan="2">10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>22</td><td>26</td><td>32</td></tr>
<tr><td>23</td><td>50/6</td><td>20...60</td><td>7,0</td><td>8,3</td><td>9,5</td><td colspan="2">11</td><td>13</td><td>15</td><td>17</td><td>19</td><td>22</td><td>25</td><td>29</td><td>35</td></tr>
<tr><td>24</td><td></td><td></td><td>50/4</td><td></td><td></td><td>7,5</td><td>8,8</td><td>10</td><td colspan="2">12</td><td>14</td><td>16</td><td>19</td><td>22</td><td>25</td><td>28</td><td>31</td><td>37</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">1. Предела прочности обрабатываемого материала</td><td colspan="8">Прочность, сигма , МПа до 590 в Коэффициент К 0,9 пп</td><td colspan="7">590...740 св. 740 1,0 1,2</td></tr>
<tr><td colspan="4">2. Формы обрабатываемой поверхности</td><td colspan="9">Поверхность Прямолинейная Коэффициент К 1,0 ф</td><td colspan="6">Криволинейная (фасонная) 1,2</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="8%"><col width="7%"><col width="8%"><col width="9%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="10" rowspan="3">Неполное штучное время Фрезерование плоскостей Сталь конструкционная, сигма = 590...740 МПа в</td><td colspan="9">Горизонтально- и вертикальнофрезерные станки</td></tr>
<tr><td colspan="9">Фрезы концевые с пластинками Т5К10</td></tr>
<tr><td colspan="9">Карта 15</td></tr>
<tr><td colspan="19">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Характер</td><td rowspan="3">Вид заготовки</td><td>Диаметр</td><td rowspan="3">Ширина обработки, В, мм</td><td rowspan="3">Число рабочих ходов, i</td><td colspan="13">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">обработки</td><td>фрезы, D, и</td><td>50</td><td>100</td><td>150</td><td colspan="2">200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>число зубьев, z</td><td colspan="13">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>Про-</td><td>16/4</td><td>10...30</td><td>1</td><td>1,6</td><td>2,0</td><td>2,2</td><td colspan="2">2,5</td><td>3,0</td><td>3,2</td><td>3,6</td><td>4,4</td><td>5,0</td><td>5,7</td><td>6,5</td><td>7,0</td></tr>
<tr><td>2</td><td>14...</td><td>кат</td><td>20/4</td><td></td><td></td><td>1,6</td><td>1,8</td><td>2,0</td><td colspan="2">2,3</td><td>2,8</td><td>3,0</td><td>3,2</td><td>4,0</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,5</td></tr>
<tr><td>3</td><td>12 квалитет</td><td rowspan="2"></td><td>40/6</td><td></td><td></td><td>1,6</td><td>1,7</td><td>1,8</td><td colspan="2">2,0</td><td>2,5</td><td>2,7</td><td>3,0</td><td>3,5</td><td>4,0</td><td>4,5</td><td>5,0</td><td>5,5</td></tr>
<tr><td>4</td><td>Rz 20;</td><td>25/4</td><td>10...30</td><td>2</td><td>4,0</td><td>4,4</td><td>5,0</td><td colspan="2">5,7</td><td>6,6</td><td>7,2</td><td>8,2</td><td>9,5</td><td>10</td><td>12</td><td>13</td><td>15</td></tr>
<tr><td>5</td><td>9 ква-</td><td></td><td>20/4</td><td>20</td><td></td><td>3,8</td><td>4,2</td><td>4,8</td><td colspan="2">5,4</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,3</td><td>9,0</td><td>10</td><td>11</td><td>13</td></tr>
<tr><td>6</td><td>литет</td><td></td><td>40/6</td><td>30</td><td></td><td>4,2</td><td>4,5</td><td>5,2</td><td colspan="2">6,0</td><td>7,0</td><td>7,5</td><td>8,5</td><td>10</td><td>11</td><td>12</td><td>14</td><td>16</td></tr>
<tr><td>7</td><td>Rz 80;</td><td>По-</td><td>16/4</td><td>10...30</td><td>2</td><td>3,5</td><td>4,0</td><td>4,5</td><td colspan="2">5,0</td><td>6,0</td><td>6,6</td><td>7,8</td><td>9,0</td><td>10</td><td>12</td><td>13</td><td>15</td></tr>
<tr><td>8</td><td>14...</td><td>ковка</td><td>20/4</td><td></td><td></td><td>3,5</td><td>3,8</td><td>4,2</td><td colspan="2">4,7</td><td>5,5</td><td>6,2</td><td>7,2</td><td>8,5</td><td>9,0</td><td>10</td><td>11</td><td>13</td></tr>
<tr><td>9</td><td>12 квалитет</td><td rowspan="2">или отливка</td><td>40/6</td><td></td><td></td><td>3,4</td><td>3,6</td><td>4,0</td><td colspan="2">4,4</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,2</td><td>8,0</td><td>9,0</td><td>10</td><td>12</td></tr>
<tr><td>10</td><td>Rz 20;</td><td>25/4</td><td>10...30</td><td>3</td><td>5,7</td><td>6,6</td><td>7,3</td><td colspan="2">8,5</td><td>9,5</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>23</td></tr>
<tr><td>11</td><td>9 ква-</td><td></td><td>20/4</td><td>20</td><td></td><td>5,6</td><td>6,4</td><td>7,0</td><td colspan="2">7,6</td><td>8,6</td><td>9,0</td><td>10</td><td>12</td><td>14</td><td>16</td><td>17</td><td>20</td></tr>
<tr><td>12</td><td>литет</td><td></td><td>40/6</td><td>30</td><td></td><td>5,7</td><td>6,5</td><td>7,2</td><td colspan="2">8,0</td><td>9,0</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>18</td><td>21</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">1. Предела прочности обрабатываемого материала</td><td colspan="8">Прочность, сигма , МПа до 590 в Коэффициент К 0,8 - 0,9 пп</td><td colspan="7">590...740 св. 740 1,0 1,2</td></tr>
<tr><td colspan="4">2. Формы обрабатываемой поверхности</td><td colspan="9">Поверхность Прямолинейная Коэффициент К 1,0 ф</td><td colspan="6">Криволинейная (фасонная) 1,2</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="9%"><col width="3%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="18">Неполное штучное время Горизонтально- и вертикально- Фрезерование уступов, Rz 40...Rz 20, фрезерные станки 11 квалитет</td></tr>
<tr><td colspan="18">Сталь конструкционная, Фрезы концевые из стали Р6М5 сигма = 590...740 МПа в Карта 16</td></tr>
<tr><td colspan="18">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фрезы,</td><td rowspan="2">Ширина фрезерования,</td><td colspan="2" rowspan="2">Глубина резания, t, мм,</td><td colspan="13">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>D, мм, и число</td><td>50</td><td>100</td><td>150</td><td>200</td><td colspan="2">250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>зубьев, z</td><td>В, мм, до</td><td colspan="2">до</td><td colspan="13">Время на рабочий ход, t , мин. нш</td></tr>
<tr><td>1</td><td>16/4</td><td>18</td><td colspan="2">5</td><td>2,4</td><td>2,7</td><td>3,2</td><td>3,5</td><td colspan="2">4,0</td><td>4,5</td><td>5,0</td><td>6,0</td><td>6,8</td><td>7,8</td><td>8,5</td><td>10</td></tr>
<tr><td>2</td><td>20/5</td><td></td><td colspan="2">10</td><td>2,5</td><td>3,0</td><td>3,5</td><td>4,0</td><td colspan="2">4,5</td><td>5,0</td><td>5,7</td><td>6,8</td><td>8,0</td><td>9,0</td><td>10</td><td>11</td></tr>
<tr><td>3</td><td>25/5</td><td></td><td colspan="2">20</td><td>2,6</td><td>3,2</td><td>3,8</td><td>4,5</td><td colspan="2">5,3</td><td>6,0</td><td>6,7</td><td>8,0</td><td>9,0</td><td>10</td><td>12</td><td>14</td></tr>
<tr><td>4</td><td></td><td></td><td colspan="2">30</td><td>3,0</td><td>4,0</td><td>4,8</td><td>5,8</td><td colspan="2">7,0</td><td>8,0</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>5</td><td></td><td></td><td colspan="2">40</td><td>3,4</td><td>4,4</td><td>5,6</td><td>6,8</td><td colspan="2">8,2</td><td>9,0</td><td>11</td><td>13</td><td>16</td><td>18</td><td>20</td><td>23</td></tr>
<tr><td>6</td><td>25/5</td><td>22</td><td colspan="2">10</td><td>2,6</td><td>3,2</td><td>3,8</td><td>4,5</td><td colspan="2">5,4</td><td>6,0</td><td>6,7</td><td>8,0</td><td>9,0</td><td>10</td><td>11</td><td>13</td></tr>
<tr><td>7</td><td></td><td></td><td colspan="2">20</td><td>2,7</td><td>3,5</td><td>4,2</td><td>5,0</td><td colspan="2">6,0</td><td>6,7</td><td>7,8</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>18</td></tr>
<tr><td>8</td><td></td><td></td><td colspan="2">30</td><td>3,5</td><td>4,5</td><td>5,6</td><td>6,7</td><td colspan="2">8,2</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>17</td><td>19</td><td>24</td></tr>
<tr><td>9</td><td></td><td></td><td colspan="2">45</td><td>4,0</td><td>5,0</td><td>6,6</td><td>8,0</td><td colspan="2">9,5</td><td>11</td><td>14</td><td>17</td><td>20</td><td>23</td><td>26</td><td>31</td></tr>
<tr><td>10</td><td>32/6</td><td>25</td><td colspan="2">10</td><td>2,8</td><td>3,4</td><td>3,9</td><td>4,6</td><td colspan="2">5,5</td><td>6,0</td><td>6,8</td><td>8,4</td><td>9,4</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>11</td><td>40/6</td><td></td><td colspan="2">20</td><td>3,0</td><td>3,8</td><td>4,5</td><td>5,5</td><td colspan="2">6,5</td><td>7,0</td><td>8,5</td><td>9,6</td><td>11</td><td>12</td><td>13</td><td>16</td></tr>
<tr><td>12</td><td>50/6</td><td></td><td colspan="2">30</td><td>3,5</td><td>4,5</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td>8,5</td><td>9,7</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>13</td><td></td><td></td><td colspan="2">40</td><td>4,0</td><td>5,0</td><td>6,0</td><td>7,5</td><td colspan="2">8,6</td><td>9,5</td><td>12</td><td>15</td><td>17</td><td>19</td><td>21</td><td>24</td></tr>
<tr><td>14</td><td></td><td></td><td colspan="2">60</td><td>4,5</td><td>5,7</td><td>7,5</td><td>8,6</td><td colspan="2">10</td><td>12</td><td>14</td><td>17</td><td>19</td><td>22</td><td>25</td><td>29</td></tr>
<tr><td>15</td><td>50/6</td><td>30</td><td colspan="2">10</td><td>3,0</td><td>3,5</td><td>4,0</td><td>4,7</td><td colspan="2">5,6</td><td>6,2</td><td>7,0</td><td>8,5</td><td>9,5</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>16</td><td></td><td></td><td colspan="2">20</td><td>3,5</td><td>4,5</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td>8,5</td><td>9,7</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>17</td><td></td><td></td><td colspan="2">30</td><td>4,0</td><td>5,0</td><td>6,0</td><td>7,5</td><td colspan="2">9,0</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>23</td></tr>
<tr><td>18</td><td></td><td></td><td colspan="2">40</td><td>4,5</td><td>5,7</td><td>7,5</td><td>9,0</td><td colspan="2">10</td><td>12</td><td>15</td><td>17</td><td>20</td><td>23</td><td>26</td><td>31</td></tr>
<tr><td>19</td><td></td><td></td><td colspan="2">60</td><td>5,0</td><td>6,7</td><td>8,6</td><td>10</td><td colspan="2">12</td><td>14</td><td>17</td><td>21</td><td>25</td><td>29</td><td>33</td><td>39</td></tr>
<tr><td>20</td><td>50/6</td><td>45</td><td colspan="2">10</td><td>3,2</td><td>4,0</td><td>4,7</td><td>5,5</td><td colspan="2">6,5</td><td>7,0</td><td>8,2</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>18</td></tr>
<tr><td>21</td><td></td><td></td><td colspan="2">20</td><td>3,8</td><td>5,0</td><td>6,0</td><td>7,5</td><td colspan="2">8,6</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>18</td><td>20</td><td>23</td></tr>
<tr><td>22</td><td></td><td></td><td colspan="2">30</td><td>4,5</td><td>6,0</td><td>7,5</td><td>8,6</td><td colspan="2">11</td><td>12</td><td>15</td><td>18</td><td>21</td><td>24</td><td>27</td><td>32</td></tr>
<tr><td>23</td><td></td><td></td><td colspan="2">40</td><td>5,0</td><td>6,7</td><td>8,6</td><td>10</td><td colspan="2">12</td><td>14</td><td>17</td><td>21</td><td>25</td><td>29</td><td>33</td><td>40</td></tr>
<tr><td>24</td><td></td><td></td><td colspan="2">60</td><td>6,0</td><td>8,0</td><td>10</td><td>12</td><td colspan="2">14</td><td>17</td><td>21</td><td>25</td><td>30</td><td>34</td><td>39</td><td>46</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
<tr><td colspan="18">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">1. Предела прочности обрабатываемого материала</td><td colspan="6">Прочность, сигма , МПа в Коэффициент К пп</td><td colspan="3">до 590 0,8 - 0,9</td><td colspan="5">590...740 св. 740 1,0 1,2</td></tr>
<tr><td colspan="4">2. Формы обрабатываемой поверхности</td><td colspan="6">Поверхность Коэффициент К ф</td><td colspan="4">Прямолинейная 1,0</td><td colspan="4">Криволинейная (фасонная) 1,2</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="4%"><col width="2%"><col width="3%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="5%"><col width="4%"><col width="2%"><col width="3%"><col width="4%"><col width="4%"><col width="5%"><col width="3%"><col width="6%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"></colgroup>
<tr><td colspan="24">Неполное штучное время Горизонтально- и вертикально-фрезерные станки Фрезерование Т-образных пазов, Rz 40...Rz 20</td></tr>
<tr><td colspan="24">Сталь конструкционная, сигма = 590...740 МПа Фрезы концевые из стали Р6М5 в</td></tr>
<tr><td colspan="24">Карта 17</td></tr>
<tr><td colspan="24">рисунок не приводится</td></tr>
<tr><td rowspan="7">N позиции</td><td rowspan="7">Длина Т-образного паза, l, мм, до</td><td colspan="22">Ширина Т-образного паза, В , мм, до 1</td></tr>
<tr><td colspan="3">16</td><td colspan="2">19</td><td colspan="2">23</td><td colspan="2">30</td><td colspan="3">37</td><td colspan="2">46</td><td colspan="2">56</td><td colspan="2">68</td><td colspan="2">80</td><td colspan="2">90</td></tr>
<tr><td colspan="22">Ширина прямоугольного паза, В, мм, до</td></tr>
<tr><td colspan="3">10</td><td colspan="2">12</td><td colspan="2">14</td><td colspan="2">18</td><td colspan="3">22</td><td colspan="2">28</td><td colspan="2">36</td><td colspan="2">42</td><td colspan="2">48</td><td colspan="2">54</td></tr>
<tr><td colspan="22">Глубина прямоугольного паза, Н, мм, до</td></tr>
<tr><td colspan="3">15 21</td><td colspan="2">17 25</td><td colspan="2">21 28</td><td colspan="2">26 36</td><td colspan="3">33 45</td><td colspan="2">40 56</td><td colspan="2">51 71</td><td colspan="2">61 85</td><td colspan="2">69 95</td><td colspan="2">79 106</td></tr>
<tr><td colspan="22">Время на один паз, t , мин. нш</td></tr>
<tr><td>1</td><td>25</td><td colspan="3">4,0 4,5</td><td colspan="2">4,8 5,0</td><td colspan="2">5,2 5,3</td><td colspan="2">5,5 5,8</td><td colspan="3">6,0 6,3</td><td colspan="2">6,5 7,0</td><td colspan="2">8,0 9,0</td><td colspan="2">8,5 9,5</td><td colspan="2">12 13</td><td colspan="2">14 18</td></tr>
<tr><td>2</td><td>50</td><td colspan="3">5,5 6,0</td><td colspan="2">6,5 7,0</td><td colspan="2">7,3 7,5</td><td colspan="2">8,0 8,2</td><td colspan="3">8,5 8,8</td><td colspan="2">9,0 9,5</td><td colspan="2">11 13</td><td colspan="2">12 14</td><td colspan="2">18 26</td><td colspan="2">21 27</td></tr>
<tr><td>3</td><td>100</td><td colspan="3">7,5 7,8</td><td colspan="2">8,0 8,2</td><td colspan="2">8,5 8,8</td><td colspan="2">9,0 9,5</td><td colspan="3">10 11</td><td colspan="2">12 13</td><td colspan="2">16 17</td><td colspan="2">18 20</td><td colspan="2">25 35</td><td colspan="2">27 37</td></tr>
<tr><td>4</td><td>150</td><td colspan="3">9,5 10</td><td colspan="2">10 11</td><td colspan="2">11 12</td><td colspan="2">12 13</td><td colspan="3">14 15</td><td colspan="2">16 17</td><td colspan="2">19 21</td><td colspan="2">23 25</td><td colspan="2">31 44</td><td colspan="2">34 46</td></tr>
<tr><td>5</td><td>200</td><td colspan="3">11 12</td><td colspan="2">12 13</td><td colspan="2">13 14</td><td colspan="2">15 16</td><td colspan="3">17 18</td><td colspan="2">19 21</td><td colspan="2">23 25</td><td colspan="2">28 29</td><td colspan="2">35 53</td><td colspan="2">37 56</td></tr>
<tr><td>6</td><td>230</td><td colspan="3">12 13</td><td colspan="2">14 15</td><td colspan="2">16 17</td><td colspan="2">18 19</td><td colspan="3">21 23</td><td colspan="2">25 27</td><td colspan="2">29 31</td><td colspan="2">33 36</td><td colspan="2">40 47</td><td colspan="2">50 66</td></tr>
<tr><td>7</td><td>300</td><td colspan="3">14 15</td><td colspan="2">15 16</td><td colspan="2">17 18</td><td colspan="2">19 21</td><td colspan="3">23 25</td><td colspan="2">27 29</td><td colspan="2">31 33</td><td colspan="2">36 42</td><td colspan="2">46 58</td><td colspan="2">60 76</td></tr>
<tr><td>8</td><td>400</td><td colspan="3">20 22</td><td colspan="2">23 25</td><td colspan="2">24 27</td><td colspan="2">26 29</td><td colspan="3">27 31</td><td colspan="2">29 33</td><td colspan="2">42 46</td><td colspan="2">45 49</td><td colspan="2">59 92</td><td colspan="2">65 97</td></tr>
<tr><td>9</td><td>500</td><td colspan="3">24 26</td><td colspan="2">27 30</td><td colspan="2">28 32</td><td colspan="2">29 33</td><td colspan="3">34 35</td><td colspan="2">36 40</td><td colspan="2">47 56</td><td colspan="2">51 60</td><td colspan="2">72 110</td><td colspan="2">79 117</td></tr>
<tr><td>10</td><td>600</td><td colspan="3">- -</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">27 35</td><td colspan="3">38 40</td><td colspan="2">40 46</td><td colspan="2">57 66</td><td colspan="2">61 70</td><td colspan="2">85 129</td><td colspan="2">95 138</td></tr>
<tr><td>11</td><td>700</td><td colspan="3">- -</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">31 38</td><td colspan="3">42 45</td><td colspan="2">45 53</td><td colspan="2">65 76</td><td colspan="2">70 82</td><td colspan="2">98 147</td><td colspan="2">107 156</td></tr>
<tr><td>12</td><td>800</td><td colspan="3">- -</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">35 45</td><td colspan="3">48 52</td><td colspan="2">53 60</td><td colspan="2">71 85</td><td colspan="2">78 93</td><td colspan="2">111 156</td><td colspan="2">121 166</td></tr>
<tr><td>13</td><td>1000</td><td colspan="3">- -</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="2">38 49</td><td colspan="3">53 56</td><td colspan="2">60 67</td><td colspan="2">79 96</td><td colspan="2">86 104</td><td colspan="2">124 191</td><td colspan="2">135 193</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td colspan="2">н о</td><td>п</td><td>р</td><td>с</td><td>т</td><td>у</td><td>ф</td></tr>
<tr><td colspan="24">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Предела прочности обрабатываемого материала</td><td colspan="8">Прочность стали, сигма , МПа в Коэффициент К пп</td><td colspan="5">до 590 0,9</td><td colspan="4">590...740 1,0</td><td colspan="3">св. 740 1,2</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="7%"><col width="9%"><col width="9%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="9">Неполное штучное время Фрезерование пазов типа "Ласточкин хвост", Rz 40...Rz 20</td><td colspan="10">Горизонтально- и вертикальнофрезерные станки</td></tr>
<tr><td colspan="9" rowspan="2">Сталь конструкционная, сигма = 590...740 МПа в</td><td colspan="10">Фрезы концевые угловые из стали Р6М5</td></tr>
<tr><td colspan="10">Карта 18</td></tr>
<tr><td colspan="19">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Глубина</td><td>Диаметр фрезы,</td><td>Угол, фи,</td><td rowspan="2">Число рабочих ходов,</td><td colspan="14">Длина обрабатываемого паза, l, мм, до</td></tr>
<tr><td rowspan="2">паза, Н, мм</td><td>D, мм, и число</td><td rowspan="2">град.</td><td>25</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td colspan="2">600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>зубьев, z</td><td>i</td><td colspan="14">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>6</td><td>10/8</td><td>70...80</td><td rowspan="2">2</td><td>4,4</td><td>4,6</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>2</td><td>8</td><td>16/10</td><td>70...80</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>10</td><td colspan="2">11</td><td>12</td><td>13</td><td>15</td></tr>
<tr><td>3</td><td></td><td></td><td>60...65</td><td rowspan="2"></td><td>4,6</td><td>5,2</td><td>6,0</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>10</td><td>11</td><td colspan="2">12</td><td>13</td><td>14</td><td>16</td></tr>
<tr><td>4</td><td>10</td><td>25/12</td><td>75...80</td><td>4,6</td><td>4,8</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>5</td><td></td><td></td><td>65...70</td><td></td><td>4,7</td><td>5,2</td><td>6,0</td><td>6,5</td><td>7,0</td><td>6,8</td><td>8,5</td><td>10</td><td>11</td><td colspan="2">12</td><td>13</td><td>14</td><td>17</td></tr>
<tr><td>6</td><td></td><td></td><td>55...60</td><td></td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11</td><td>13</td><td colspan="2">15</td><td>17</td><td>19</td><td>22</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Предела прочности обрабатываемого материала</td><td colspan="5">Прочность, сигма , МПа в Коэффициент К пп</td><td colspan="2">до 590 0,9</td><td colspan="4">590...740 1,0</td><td colspan="4">св. 740 1,2</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="8%"><col width="7%"><col width="5%"><col width="4%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="20">Неполное штучное время Горизонтально- и вертикально- Фрезерование пазов, Rz 40...Rz 20; 11 квалитет фрезерные станки Сталь конструкционная, сигма = 590...740 МПа в Фрезы концевые из стали Т15К6, Р6М5</td></tr>
<tr><td colspan="20">Карта 19</td></tr>
<tr><td colspan="20">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Режущий</td><td>Ширина</td><td colspan="2" rowspan="3">Глубина паза, Н, мм, до</td><td rowspan="3">Число рабочих ходов, i</td><td colspan="14">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">инструмент</td><td>паза, В,</td><td>25</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td colspan="2">600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>мм, до</td><td colspan="14">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>Фрезы</td><td>6</td><td colspan="2">3</td><td>1</td><td>2,0</td><td>2,3</td><td>3,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>концевые из</td><td></td><td colspan="2">5</td><td rowspan="2"></td><td>2,5</td><td>3,2</td><td>4,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>стали</td><td>10</td><td colspan="2">8</td><td>1,8</td><td>2,1</td><td>2,8</td><td>3,1</td><td>3,5</td><td>4,3</td><td>5,0</td><td>5,9</td><td>7,2</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td rowspan="2">Р6М5</td><td></td><td colspan="2">12</td><td rowspan="2"></td><td>2,1</td><td>2,5</td><td>3,5</td><td>4,6</td><td>5,5</td><td>6,9</td><td>7,9</td><td>10</td><td>12</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>16</td><td colspan="2">16</td><td>2,0</td><td>2,4</td><td>3,1</td><td>3,9</td><td>4,6</td><td>5,6</td><td>6,5</td><td>7,9</td><td>9,5</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td rowspan="2"></td><td></td><td colspan="2">20</td><td rowspan="2"></td><td>2,3</td><td>2,7</td><td>3,8</td><td>4,7</td><td>5,8</td><td>7,2</td><td>8,2</td><td>10</td><td>12</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>25</td><td colspan="2">16</td><td>1,8</td><td>2,0</td><td>2,4</td><td>2,8</td><td>3,3</td><td>4,0</td><td>4,5</td><td>5,3</td><td>6,4</td><td colspan="2">7,3</td><td>8,2</td><td>9,0</td><td>10</td></tr>
<tr><td>8</td><td></td><td></td><td colspan="2">20</td><td></td><td>2,0</td><td>2,4</td><td>3,2</td><td>4,0</td><td>4,7</td><td>5,9</td><td>6,6</td><td>8,2</td><td>10</td><td colspan="2">12</td><td>14</td><td>16</td><td>19</td></tr>
<tr><td>9</td><td rowspan="2"></td><td></td><td colspan="2">30</td><td rowspan="2"></td><td>2,3</td><td>2,7</td><td>3,5</td><td>4,4</td><td>5,3</td><td>6,4</td><td>7,3</td><td>9,0</td><td>11</td><td colspan="2">13</td><td>15</td><td>17</td><td>21</td></tr>
<tr><td>10</td><td>32</td><td colspan="2">20</td><td>2,3</td><td>2,8</td><td>3,6</td><td>4,5</td><td>5,4</td><td>6,6</td><td>7,3</td><td>9,0</td><td>11</td><td colspan="2">13</td><td>15</td><td>17</td><td>21</td></tr>
<tr><td>11</td><td rowspan="2"></td><td></td><td colspan="2">30</td><td></td><td>2,5</td><td>3,2</td><td>4,3</td><td>5,3</td><td>6,4</td><td>7,8</td><td>8,8</td><td>10</td><td>12</td><td colspan="2">14</td><td>16</td><td>18</td><td>22</td></tr>
<tr><td>12</td><td>40</td><td colspan="2">30</td><td>2</td><td>5,2</td><td>7,3</td><td>10</td><td>12</td><td>15</td><td>18</td><td>21</td><td>27</td><td>32</td><td colspan="2">37</td><td>42</td><td>47</td><td>60</td></tr>
<tr><td>13</td><td rowspan="2"></td><td></td><td colspan="2">40</td><td rowspan="2"></td><td>6,4</td><td>10</td><td>12</td><td>14</td><td>18</td><td>21</td><td>25</td><td>32</td><td>38</td><td colspan="2">47</td><td>54</td><td>61</td><td>76</td></tr>
<tr><td>14</td><td>50</td><td colspan="2">30</td><td>6,8</td><td>9,5</td><td>13</td><td>16</td><td>20</td><td>24</td><td>27</td><td>34</td><td>41</td><td colspan="2">48</td><td>55</td><td>62</td><td>77</td></tr>
<tr><td>15</td><td></td><td></td><td colspan="2">40</td><td></td><td>7,7</td><td>11</td><td>15</td><td>18</td><td>21</td><td>25</td><td>29</td><td>38</td><td>47</td><td colspan="2">56</td><td>64</td><td>73</td><td>90</td></tr>
<tr><td>16</td><td>Фрезы</td><td>10</td><td colspan="2">8</td><td>1</td><td>1,5</td><td>1,6</td><td>2,0</td><td>2,3</td><td>2,4</td><td>3,1</td><td>3,3</td><td>3,8</td><td>4,6</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td>концевые с</td><td></td><td colspan="2">12</td><td rowspan="2"></td><td>1,6</td><td>1,8</td><td>2,2</td><td>2,4</td><td>2,7</td><td>3,3</td><td>3,5</td><td>4,3</td><td>5,1</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td>плас-</td><td>16</td><td colspan="2">16</td><td>1,8</td><td>2,0</td><td>2,4</td><td>2,7</td><td>3,2</td><td>4,0</td><td>4,3</td><td>5,2</td><td>6,3</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td>тинками</td><td></td><td colspan="2">20</td><td rowspan="2"></td><td>2,0</td><td>2,4</td><td>3,2</td><td>4,0</td><td>4,7</td><td>5,6</td><td>6,5</td><td>8,2</td><td>10</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>Т15К6</td><td>25</td><td colspan="2">16</td><td>1,7</td><td>1,8</td><td>2,3</td><td>2,7</td><td>3,0</td><td>3,8</td><td>4,2</td><td>5,0</td><td>5,8</td><td colspan="2">6,5</td><td>7,5</td><td>8,5</td><td>10</td></tr>
<tr><td>21</td><td></td><td></td><td colspan="2">20</td><td></td><td>1,9</td><td>2,0</td><td>2,4</td><td>2,8</td><td>3,2</td><td>3,9</td><td>4,4</td><td>5,2</td><td>6,0</td><td colspan="2">7,0</td><td>8,0</td><td>9,0</td><td>10</td></tr>
<tr><td>22</td><td rowspan="2"></td><td></td><td colspan="2">30</td><td rowspan="2"></td><td>2,0</td><td>2,2</td><td>2,7</td><td>3,2</td><td>3,6</td><td>4,5</td><td>5,0</td><td>6,0</td><td>7,0</td><td colspan="2">8,0</td><td>9,0</td><td>10</td><td>12</td></tr>
<tr><td>23</td><td>32</td><td colspan="2">20</td><td>2,1</td><td>2,4</td><td>3,2</td><td>3,9</td><td>4,6</td><td>5,8</td><td>6,2</td><td>7,5</td><td>9,0</td><td colspan="2">10</td><td>11</td><td>13</td><td>15</td></tr>
<tr><td>24</td><td rowspan="2"></td><td></td><td colspan="2">30</td><td></td><td>2,4</td><td>2,8</td><td>3,8</td><td>4,5</td><td>5,4</td><td>6,8</td><td>7,7</td><td>9,0</td><td>11</td><td colspan="2">13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>25</td><td>40</td><td colspan="2">30</td><td>2</td><td>4,5</td><td>6,0</td><td>7,5</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>19</td><td>23</td><td colspan="2">26</td><td>29</td><td>33</td><td>40</td></tr>
<tr><td>26</td><td rowspan="2"></td><td></td><td colspan="2">40</td><td rowspan="2"></td><td>5,0</td><td>6,5</td><td>8,7</td><td>10</td><td>13</td><td>15</td><td>18</td><td>22</td><td>27</td><td colspan="2">31</td><td>35</td><td>40</td><td>48</td></tr>
<tr><td>27</td><td>50</td><td colspan="2">30</td><td>5,4</td><td>7,1</td><td>9,0</td><td>11</td><td>14</td><td>16</td><td>19</td><td>23</td><td>28</td><td colspan="2">32</td><td>36</td><td>41</td><td>49</td></tr>
<tr><td>28</td><td></td><td></td><td colspan="2">40</td><td></td><td>6,0</td><td>8,3</td><td>11</td><td>13</td><td>16</td><td>19</td><td>23</td><td>28</td><td>33</td><td colspan="2">39</td><td>45</td><td>50</td><td>60</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
<tr><td colspan="20">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">1. Предела прочности обрабатываемого материала</td><td colspan="12">Прочность, сигма , МПа до 590 590...740 в Коэффициент К 0,9 1,0 пп</td><td colspan="4">св. 740 1,2</td></tr>
<tr><td colspan="4">2. Формы обрабатываемой поверхности</td><td colspan="16">Поверхность Прямолинейная Криволинейная (фасонная) Коэффициент К 1,0 1,2 ф</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="8%"><col width="10%"><col width="6%"><col width="4%"><col width="8%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="9" rowspan="3">Неполное штучное время Фрезерование плоскостей Медные сплавы, НВ = 980...1370 МПа</td><td colspan="10">Горизонтально- и вертикально-фрезерные станки</td></tr>
<tr><td colspan="10">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="10">Карта 20</td></tr>
<tr><td colspan="19">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Характер</td><td>Диаметр фрезы,</td><td colspan="2" rowspan="3">Ширина обработки, В, мм</td><td rowspan="2">Число рабочих ходов,</td><td colspan="13">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">обработки</td><td>D, и число</td><td>50</td><td>100</td><td colspan="2">150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>зубьев, z</td><td>i</td><td colspan="13">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80; 14</td><td>16/4</td><td colspan="2">20...30</td><td rowspan="2">1</td><td>1,6</td><td>1,8</td><td colspan="2">2,1</td><td>2,4</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>квали-</td><td>20/5</td><td colspan="2">20...40</td><td>1,7</td><td>1,9</td><td colspan="2">2,2</td><td>2,6</td><td>2,9</td><td>3,2</td><td>3,6</td><td>4,2</td><td>4,7</td><td>5,3</td><td>6,0</td><td>7,2</td></tr>
<tr><td>3</td><td rowspan="2">тет</td><td>32/6</td><td colspan="2"></td><td rowspan="2"></td><td>1,8</td><td>2,0</td><td colspan="2">2,3</td><td>2,7</td><td>3,3</td><td>3,7</td><td>4,3</td><td>5,0</td><td>5,8</td><td>6,7</td><td>7,6</td><td>8,5</td></tr>
<tr><td>4</td><td>40/6</td><td colspan="2">20...60</td><td>1,9</td><td>2,2</td><td colspan="2">2,5</td><td>2,9</td><td>3,5</td><td>4,0</td><td>4,6</td><td>5,3</td><td>6,2</td><td>7,1</td><td>8,0</td><td>9,0</td></tr>
<tr><td>5</td><td></td><td>50/6</td><td colspan="2"></td><td></td><td>2,0</td><td>2,4</td><td colspan="2">2,7</td><td>3,2</td><td>3,8</td><td>4,3</td><td>5,0</td><td>5,7</td><td>6,6</td><td>7,5</td><td>8,6</td><td>9,5</td></tr>
<tr><td>6</td><td>Rz 20;</td><td>16/4</td><td colspan="2">20...30</td><td>2</td><td>3,8</td><td>4,2</td><td colspan="2">4,5</td><td>5,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>9 ква-</td><td>20/5</td><td colspan="2">20...40</td><td></td><td>3,9</td><td>4,3</td><td colspan="2">4,7</td><td>5,2</td><td>5,9</td><td>6,4</td><td>7,3</td><td>8,4</td><td>9,5</td><td>11</td><td>12</td><td>13</td></tr>
<tr><td>8</td><td>литет</td><td>32/6</td><td colspan="2">20...50</td><td></td><td>4,1</td><td>4,5</td><td colspan="2">4,9</td><td>5,4</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td><td>12</td><td>13</td><td>15</td></tr>
<tr><td>9</td><td></td><td>40/6</td><td colspan="2">20...60</td><td></td><td>4,5</td><td>5,0</td><td colspan="2">6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td><td>11</td><td>12</td><td>13</td><td>14</td><td>16</td></tr>
<tr><td>10</td><td></td><td>50/6</td><td colspan="2"></td><td></td><td>5,0</td><td>6,0</td><td colspan="2">7,0</td><td>8,0</td><td>9,0</td><td>10</td><td>11</td><td>12</td><td>13</td><td>14</td><td>15</td><td>17</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">1. Твердости обрабатываемого сплава</td><td colspan="8">Твердость, НВ, МПа 590...880 Коэффициент К 0,7 тв</td><td colspan="7">980...1370 1370...2450 1,0 1,20</td></tr>
<tr><td colspan="4">2. Формы обрабатываемой поверхности</td><td colspan="9">Поверхность Прямолинейная Коэффициент К 1,0 ф</td><td colspan="6">Криволинейная (фасонная) 1,2</td></tr>
<tr><td colspan="4">3. Материала режущего инструмента</td><td colspan="9">Режущий инструмент Резцы из стали Р6М5 Коэффициент К 1,0 ри</td><td colspan="6">Резцы с пластинками ВК8 0,6</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="9%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="16">Неполное штучное время Горизонтально- и вертикально- Фрезерование уступов, Rz 40...Rz 20, фрезерные станки 11 квалитет</td></tr>
<tr><td colspan="16">Медные сплавы, НВ = 980...1370 МПа Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="16">Карта 21</td></tr>
<tr><td colspan="16">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фрезы,</td><td rowspan="2">Ширина фрезерования,</td><td rowspan="3">Глубина резания, t, мм</td><td colspan="12">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>D, мм, и число</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>зубьев, z</td><td>В, мм, до</td><td colspan="12">Время на проход, t , мин. нш</td></tr>
<tr><td>1</td><td>16/4</td><td>18</td><td>5</td><td>2,2</td><td>2,4</td><td>2,6</td><td>2,8</td><td>3,4</td><td>3,6</td><td>4,0</td><td>4,7</td><td>5,3</td><td>6,0</td><td>6,4</td><td>7,0</td></tr>
<tr><td>2</td><td></td><td></td><td>10</td><td>2,3</td><td>2,5</td><td>2,7</td><td>3,0</td><td>3,5</td><td>4,0</td><td>4,4</td><td>5,3</td><td>5,7</td><td>6,7</td><td>7,3</td><td>8,0</td></tr>
<tr><td>3</td><td></td><td></td><td>20</td><td>2,4</td><td>2,6</td><td>3,0</td><td>3,4</td><td>4,0</td><td>4,4</td><td>5,0</td><td>6,0</td><td>6,7</td><td>7,8</td><td>8,5</td><td>9,0</td></tr>
<tr><td>4</td><td></td><td></td><td>30</td><td>2,5</td><td>2,7</td><td>3,5</td><td>3,8</td><td>4,8</td><td>5,4</td><td>6,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11</td><td>12</td></tr>
<tr><td>5</td><td></td><td></td><td>40</td><td>2,7</td><td>3,4</td><td>4,2</td><td>5,3</td><td>6,0</td><td>6,7</td><td>7,8</td><td>9,0</td><td>11</td><td>13</td><td>14</td><td>16</td></tr>
<tr><td>6</td><td>25/5</td><td>22</td><td>10</td><td>2,4</td><td>2,6</td><td>2,8</td><td>3,2</td><td>3,7</td><td>4,2</td><td>4,5</td><td>5,5</td><td>6,0</td><td>6,8</td><td>7,8</td><td>8,5</td></tr>
<tr><td>7</td><td></td><td></td><td>20</td><td>2,5</td><td>2,8</td><td>3,2</td><td>3,5</td><td>4,2</td><td>4,5</td><td>5,2</td><td>6,2</td><td>7,0</td><td>8,0</td><td>8,7</td><td>9,5</td></tr>
<tr><td>8</td><td></td><td></td><td>30</td><td>2,6</td><td>3,0</td><td>3,6</td><td>4,0</td><td>5,0</td><td>5,5</td><td>6,3</td><td>7,8</td><td>9,0</td><td>10</td><td>12</td><td>13</td></tr>
<tr><td>9</td><td></td><td></td><td>45</td><td>2,8</td><td>3,5</td><td>4,5</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td>12</td><td>14</td><td>15</td><td>17</td></tr>
<tr><td>10</td><td>32/6</td><td>25</td><td>10</td><td>2,3</td><td>2,5</td><td>2,7</td><td>3,0</td><td>3,6</td><td>4,0</td><td>4,4</td><td>5,4</td><td>5,8</td><td>6,7</td><td>7,5</td><td>8,4</td></tr>
<tr><td>11</td><td></td><td></td><td>20</td><td>2,4</td><td>2,7</td><td>3,0</td><td>3,4</td><td>4,0</td><td>4,4</td><td>5,0</td><td>6,0</td><td>6,8</td><td>7,8</td><td>8,6</td><td>9,4</td></tr>
<tr><td>12</td><td></td><td></td><td>30</td><td>2,5</td><td>2,8</td><td>3,5</td><td>3,8</td><td>4,5</td><td>5,0</td><td>5,8</td><td>7,4</td><td>8,5</td><td>9,0</td><td>10</td><td>12</td></tr>
<tr><td>13</td><td></td><td></td><td>40</td><td>2,7</td><td>3,0</td><td>4,0</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,5</td><td>9,5</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>14</td><td></td><td></td><td>60</td><td>3,2</td><td>3,8</td><td>4,5</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,5</td><td>10</td><td>11</td><td>13</td><td>15</td><td>18</td></tr>
<tr><td>15</td><td>50/6</td><td>30</td><td>10</td><td>2,4</td><td>2,8</td><td>3,2</td><td>3,5</td><td>4,0</td><td>4,5</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,0</td><td>8,6</td><td>10</td></tr>
<tr><td>16</td><td></td><td></td><td>20</td><td>2,5</td><td>3,0</td><td>3,5</td><td>4,0</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td><td>11</td></tr>
<tr><td>17</td><td></td><td></td><td>30</td><td>3,0</td><td>3,5</td><td>4,0</td><td>4,7</td><td>5,6</td><td>6,0</td><td>7,0</td><td>8,5</td><td>9,5</td><td>11</td><td>12</td><td>13</td></tr>
<tr><td>18</td><td></td><td></td><td>40</td><td>3,2</td><td>3,8</td><td>4,5</td><td>5,4</td><td>6,5</td><td>7,0</td><td>8,2</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>19</td></tr>
<tr><td>19</td><td></td><td></td><td>60</td><td>3,4</td><td>4,4</td><td>5,4</td><td>6,5</td><td>7,5</td><td>8,5</td><td>11</td><td>12</td><td>14</td><td>16</td><td>18</td><td>23</td></tr>
<tr><td>20</td><td>50/6</td><td>45</td><td>10</td><td>2,6</td><td>3,2</td><td>3,6</td><td>4,2</td><td>4,8</td><td>5,4</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td><td>11</td></tr>
<tr><td>21</td><td></td><td></td><td>20</td><td>3,0</td><td>3,5</td><td>4,0</td><td>4,7</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,5</td><td>9,5</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>22</td><td></td><td></td><td>30</td><td>3,2</td><td>3,8</td><td>4,5</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>18</td></tr>
<tr><td>23</td><td></td><td></td><td>40</td><td>3,5</td><td>4,5</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>22</td></tr>
<tr><td>24</td><td></td><td></td><td>60</td><td>4,0</td><td>5,0</td><td>6,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11</td><td>14</td><td>17</td><td>19</td><td>21</td><td>25</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
<tr><td colspan="16">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">1. Твердости обрабатываемого сплава</td><td colspan="4">Твердость, НВ, МПа Коэффициент К тв</td><td colspan="9">590...880 980...1370 1470...2450 0,7 1,0 1,20</td></tr>
<tr><td colspan="3">2. Формы обрабатываемой поверхности</td><td colspan="4">Поверхность Коэффициент К ф</td><td colspan="9">Прямолинейная Криволинейная (фасонная) 1,0 1,2</td></tr>
<tr><td colspan="3">3. Материала режущего инструмента</td><td colspan="4">Режущий инструмент Коэффициент К ри</td><td colspan="9">Резцы из стали Резцы с пластинками Р6М5 ВК8 1,0 0,6</td></tr>
</table>


<a id="p100716"></a>Примечание: Карта рассчитана на фрезерование уступов типа А. При фрезеровании уступов типа Б неполное штучное время следует применять с коэффициентом К = 0,85 (припуск h = t мм учитывался согласно ГОСТу 1855-55).


<table>
<colgroup><col width="5%"><col width="8%"><col width="9%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="21">Неполное штучное время Горизонтально- и вертикально- Фрезерование пазов, Rz 40...Rz 20; фрезерные станки 11 квалитет</td></tr>
<tr><td colspan="21">Медные сплавы, НВ = 980...1370 МПа Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="21">Карта 22</td></tr>
<tr><td colspan="21">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина</td><td rowspan="3">Глубина паза, Н, мм, до</td><td colspan="2" rowspan="3">Число рабочих ходов, i</td><td colspan="16">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>паза, В,</td><td>25</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td colspan="2">300</td><td colspan="2">400</td><td>500</td><td colspan="2">600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>мм, до</td><td colspan="16">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>6</td><td>3</td><td colspan="2">1</td><td>1,6</td><td>1,9</td><td>2,3</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td></td><td>5</td><td colspan="2" rowspan="2"></td><td>2,0</td><td>2,3</td><td>3,1</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>10</td><td>8</td><td>1,5</td><td>1,6</td><td>2,0</td><td>2,2</td><td>2,6</td><td>3,1</td><td colspan="2">3,6</td><td colspan="2">4,2</td><td>5,2</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td></td><td>12</td><td colspan="2" rowspan="2"></td><td>1,7</td><td>2,0</td><td>2,5</td><td>3,7</td><td>3,2</td><td>3,8</td><td colspan="2">4,5</td><td colspan="2">5,3</td><td>6,3</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>16</td><td>16</td><td>1,6</td><td>1,8</td><td>2,2</td><td>2,6</td><td>3,0</td><td>3,8</td><td colspan="2">4,4</td><td colspan="2">5,2</td><td>6,2</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td></td><td>20</td><td colspan="2" rowspan="2"></td><td>1,8</td><td>2,0</td><td>2,4</td><td>2,8</td><td>3,3</td><td>4,0</td><td colspan="2">4,7</td><td colspan="2">5,5</td><td>6,5</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>25</td><td>16</td><td>1,4</td><td>1,5</td><td>1,7</td><td>2,0</td><td>2,2</td><td>2,7</td><td colspan="2">3,0</td><td colspan="2">3,4</td><td>4,2</td><td colspan="2">4,5</td><td>5,0</td><td>5,5</td><td>6,0</td></tr>
<tr><td>8</td><td></td><td>20</td><td colspan="2"></td><td>1,5</td><td>1,7</td><td>2,0</td><td>2,3</td><td>2,7</td><td>3,4</td><td colspan="2">4,0</td><td colspan="2">4,5</td><td>5,6</td><td colspan="2">6,2</td><td>7,0</td><td>7,5</td><td>8,5</td></tr>
<tr><td>9</td><td></td><td>30</td><td colspan="2" rowspan="2"></td><td>1,6</td><td>2,0</td><td>2,4</td><td>3,0</td><td>3,4</td><td>4,2</td><td colspan="2">4,8</td><td colspan="2">5,7</td><td>6,6</td><td colspan="2">7,7</td><td>8,4</td><td>9,6</td><td>10</td></tr>
<tr><td>10</td><td>32</td><td>20</td><td>1,6</td><td>1,8</td><td>2,0</td><td>2,4</td><td>2,8</td><td>3,5</td><td colspan="2">4,2</td><td colspan="2">4,6</td><td>5,7</td><td colspan="2">6,3</td><td>7,0</td><td>7,6</td><td>8,6</td></tr>
<tr><td>11</td><td></td><td>30</td><td colspan="2"></td><td>1,8</td><td>2,0</td><td>2,5</td><td>3,0</td><td>3,5</td><td>4,2</td><td colspan="2">5,5</td><td colspan="2">5,8</td><td>6,8</td><td colspan="2">7,8</td><td>8,5</td><td>9,0</td><td>10</td></tr>
<tr><td>12</td><td>40</td><td>50</td><td colspan="2">2</td><td>3,6</td><td>4,7</td><td>5,9</td><td>7,1</td><td>8,1</td><td>9,5</td><td colspan="2">11</td><td colspan="2">13</td><td>15</td><td colspan="2">18</td><td>20</td><td>22</td><td>25</td></tr>
<tr><td>13</td><td></td><td>70</td><td colspan="2" rowspan="2"></td><td>3,8</td><td>5,2</td><td>6,6</td><td>8,1</td><td>9,5</td><td>11</td><td colspan="2">13</td><td colspan="2">16</td><td>18</td><td colspan="2">21</td><td>24</td><td>26</td><td>29</td></tr>
<tr><td>14</td><td>50</td><td>50</td><td>4,0</td><td>5,4</td><td>7,0</td><td>8,3</td><td>9,5</td><td>11</td><td colspan="2">13</td><td colspan="2">16</td><td>18</td><td colspan="2">21</td><td>24</td><td>26</td><td>29</td></tr>
<tr><td>15</td><td></td><td>70</td><td colspan="2"></td><td>4,5</td><td>6,2</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td colspan="2">15</td><td colspan="2">18</td><td>21</td><td colspan="2">26</td><td>29</td><td>33</td><td>39</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td colspan="2">з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
<tr><td colspan="21">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">1. Твердости обрабатываемого сплава</td><td colspan="8">Твердость, НВ, МПа 590...880 Коэффициент К 0,7 тв</td><td colspan="5">980...1370 1,0</td><td colspan="4">1480...2450 1,20</td></tr>
<tr><td colspan="4">2. Формы обрабатываемой поверхности</td><td colspan="10">Поверхность Прямолинейная Коэффициент К 1,0 ф</td><td colspan="7">Криволинейная (фасонная) 1,2</td></tr>
<tr><td colspan="4">3. Материала режущего инструмента</td><td colspan="10">Режущий инструмент Резцы из стали Р6М5 Коэффициент К 1,0 ри</td><td colspan="7">Резцы с пластинками ВК8 0,6</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="8%"><col width="9%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="17">Неполное штучное время Горизонтально-фрезерные станки Фрезерование пазов, Rz 40...Rz 20; 11 квалитет Фрезы дисковые трехсторонние из Чугун серый, НВ = 1760...2150 МПа стали Р6М5</td></tr>
<tr><td colspan="17">Карта 23</td></tr>
<tr><td colspan="17">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина</td><td rowspan="3">Глубина паза, Н, мм, до</td><td rowspan="3">Число рабочих ходов, i</td><td colspan="13">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>паза, В,</td><td>25</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>мм, до</td><td colspan="13">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>25</td><td>10</td><td>1</td><td>2,0</td><td>2,4</td><td>2,5</td><td>2,7</td><td>3,2</td><td>3,5</td><td>3,9</td><td>4,4</td><td>5,0</td><td>5,8</td><td>6,6</td><td>7,2</td><td>8,4</td></tr>
<tr><td>2</td><td rowspan="2"></td><td>15</td><td></td><td>2,2</td><td>2,6</td><td>2,7</td><td>3,2</td><td>3,5</td><td>4,3</td><td>4,7</td><td>5,3</td><td>6,4</td><td>7,2</td><td>8,3</td><td>9,0</td><td>11</td></tr>
<tr><td>3</td><td>20</td><td>2</td><td>3,2</td><td>4,3</td><td>4,5</td><td>4,9</td><td>5,7</td><td>6,4</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td><td>12</td><td>13</td><td>15</td></tr>
<tr><td>4</td><td></td><td>30</td><td></td><td>3,6</td><td>4,7</td><td>4,9</td><td>5,7</td><td>6,4</td><td>7,7</td><td>8,5</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>16</td><td>20</td></tr>
<tr><td>5</td><td>28</td><td>10</td><td>1</td><td>2,1</td><td>2,4</td><td>2,7</td><td>3,1</td><td>3,4</td><td>4,0</td><td>4,5</td><td>5,0</td><td>5,9</td><td>6,7</td><td>7,7</td><td>8,4</td><td>10</td></tr>
<tr><td>6</td><td rowspan="2"></td><td>15</td><td></td><td>2,3</td><td>2,8</td><td>2,9</td><td>3,4</td><td>4,2</td><td>4,7</td><td>5,4</td><td>6,2</td><td>7,3</td><td>8,5</td><td>10</td><td>11</td><td>15</td></tr>
<tr><td>7</td><td>20</td><td>2</td><td>3,4</td><td>4,4</td><td>4,9</td><td>5,5</td><td>6,2</td><td>7,2</td><td>8,2</td><td>9,0</td><td>11</td><td>12</td><td>14</td><td>15</td><td>18</td></tr>
<tr><td>8</td><td></td><td>30</td><td></td><td>3,8</td><td>5,1</td><td>5,3</td><td>6,1</td><td>7,5</td><td>8,5</td><td>10</td><td>11</td><td>13</td><td>15</td><td>18</td><td>20</td><td>26</td></tr>
<tr><td>9</td><td>32</td><td>10</td><td>1</td><td>2,4</td><td>2,9</td><td>3,2</td><td>3,8</td><td>4,4</td><td>5,2</td><td>5,8</td><td>7,0</td><td>8,2</td><td>9,0</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>10</td><td rowspan="2"></td><td>15</td><td></td><td>2,7</td><td>3,4</td><td>3,8</td><td>4,6</td><td>5,4</td><td>6,5</td><td>7,2</td><td>8,5</td><td>10</td><td>12</td><td>14</td><td>16</td><td>19</td></tr>
<tr><td>11</td><td>20</td><td>2</td><td>3,9</td><td>5,3</td><td>5,7</td><td>6,9</td><td>7,8</td><td>9,0</td><td>10</td><td>12</td><td>15</td><td>17</td><td>19</td><td>21</td><td>25</td></tr>
<tr><td>12</td><td></td><td>30</td><td></td><td>4,5</td><td>6,2</td><td>6,9</td><td>8,4</td><td>10</td><td>12</td><td>13</td><td>16</td><td>19</td><td>22</td><td>25</td><td>28</td><td>34</td></tr>
<tr><td>13</td><td>36</td><td>20</td><td>2</td><td>4,0</td><td>5,4</td><td>5,9</td><td>7,3</td><td>8,2</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td><td>22</td><td>26</td></tr>
<tr><td>14</td><td></td><td>30</td><td></td><td>4,7</td><td>6,4</td><td>7,3</td><td>8,6</td><td>10</td><td>12</td><td>13</td><td>16</td><td>19</td><td>22</td><td>26</td><td>30</td><td>36</td></tr>
<tr><td>15</td><td></td><td>40</td><td></td><td>5,2</td><td>7,3</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>18</td><td>21</td><td>25</td><td>29</td><td>32</td><td>38</td></tr>
<tr><td>16</td><td>45</td><td>20</td><td>2</td><td>4,7</td><td>6,4</td><td>7,1</td><td>8,2</td><td>9,5</td><td>11</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>22</td><td>26</td></tr>
<tr><td>17</td><td></td><td>30</td><td></td><td>5,2</td><td>7,3</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>18</td><td>21</td><td>24</td><td>27</td><td>30</td><td>35</td></tr>
<tr><td>18</td><td></td><td>40</td><td></td><td>5,6</td><td>8,0</td><td>8,5</td><td>10</td><td>12</td><td>14</td><td>16</td><td>19</td><td>22</td><td>25</td><td>29</td><td>33</td><td>39</td></tr>
<tr><td>19</td><td></td><td>50</td><td></td><td>6,4</td><td>9,0</td><td>10</td><td>12</td><td>14</td><td>16</td><td>19</td><td>23</td><td>27</td><td>31</td><td>35</td><td>40</td><td>48</td></tr>
<tr><td>20</td><td>50</td><td>30</td><td>2</td><td>5,4</td><td>7,8</td><td>8,7</td><td>10</td><td>12</td><td>13</td><td>15</td><td>18</td><td>22</td><td>25</td><td>29</td><td>32</td><td>38</td></tr>
<tr><td>21</td><td></td><td>40</td><td></td><td>6,4</td><td>9,0</td><td>10</td><td>12</td><td>14</td><td>17</td><td>19</td><td>23</td><td>27</td><td>31</td><td>35</td><td>40</td><td>48</td></tr>
<tr><td>22</td><td></td><td>50</td><td></td><td>8,2</td><td>12</td><td>14</td><td>16</td><td>18</td><td>21</td><td>24</td><td>29</td><td>34</td><td>39</td><td>44</td><td>49</td><td>60</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">Твердости обрабатываемого материала</td><td colspan="7">Твердость чугуна, НВ, МПа Коэффициент К тв</td><td colspan="7">до 2150 св. 2150 1,0 1,2</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="8%"><col width="9%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="17">Неполное штучное время Горизонтально-фрезерные станки Фрезерование пазов, Rz 40...Rz 20; 11 квалитет Фрезы дисковые трехсторонние из Сталь конструкционная, стали Р6М5 сигма = 590...740 МПа в Карта 24</td></tr>
<tr><td colspan="17">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина</td><td rowspan="3">Глубина паза, Н, мм, до</td><td rowspan="3">Число рабочих ходов, i</td><td colspan="13">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>паза, В,</td><td>25</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>мм, до</td><td colspan="13">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>25</td><td>10</td><td>1</td><td>2,2</td><td>2,6</td><td>2,8</td><td>3,0</td><td>3,4</td><td>3,7</td><td>4,0</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>11</td></tr>
<tr><td>2</td><td rowspan="2"></td><td>15</td><td></td><td>2,5</td><td>3,2</td><td>3,6</td><td>4,5</td><td>5,1</td><td>6,2</td><td>7,0</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>3</td><td>20</td><td>2</td><td>3,6</td><td>4,7</td><td>5,2</td><td>6,0</td><td>6,8</td><td>7,2</td><td>8,0</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>4</td><td></td><td>30</td><td></td><td>4,2</td><td>5,7</td><td>6,5</td><td>8,2</td><td>9,0</td><td>11</td><td>13</td><td>16</td><td>19</td><td>22</td><td>25</td><td>28</td><td>33</td></tr>
<tr><td>5</td><td>28</td><td>10</td><td>1</td><td>2,2</td><td>2,6</td><td>2,8</td><td>3,4</td><td>3,7</td><td>4,5</td><td>5,0</td><td>5,6</td><td>6,9</td><td>7,8</td><td>8,9</td><td>10</td><td>12</td></tr>
<tr><td>6</td><td rowspan="2"></td><td>15</td><td></td><td>2,6</td><td>3,4</td><td>3,8</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>7</td><td>20</td><td>2</td><td>3,6</td><td>4,8</td><td>5,3</td><td>6,2</td><td>7,0</td><td>8,2</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>16</td><td>18</td><td>21</td></tr>
<tr><td>8</td><td></td><td>30</td><td></td><td>4,5</td><td>6,0</td><td>6,8</td><td>9,0</td><td>9,5</td><td>11</td><td>13</td><td>16</td><td>19</td><td>21</td><td>24</td><td>28</td><td>34</td></tr>
<tr><td>9</td><td>32</td><td>10</td><td>1</td><td>2,5</td><td>3,2</td><td>4,0</td><td>4,3</td><td>5,0</td><td>5,9</td><td>6,7</td><td>7,8</td><td>9,5</td><td>11</td><td>12</td><td>14</td><td>17</td></tr>
<tr><td>10</td><td rowspan="2"></td><td>15</td><td></td><td>3,0</td><td>3,7</td><td>4,2</td><td>5,2</td><td>6,5</td><td>7,8</td><td>8,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>19</td><td>23</td></tr>
<tr><td>11</td><td>20</td><td>2</td><td>4,0</td><td>5,7</td><td>7,2</td><td>7,7</td><td>9,0</td><td>10</td><td>12</td><td>14</td><td>17</td><td>19</td><td>22</td><td>25</td><td>31</td></tr>
<tr><td>12</td><td></td><td>30</td><td></td><td>4,7</td><td>6,7</td><td>7,5</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>19</td><td>23</td><td>27</td><td>31</td><td>35</td><td>42</td></tr>
<tr><td>13</td><td>36</td><td>20</td><td>2</td><td>4,5</td><td>6,2</td><td>7,7</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>18</td><td>20</td><td>23</td><td>26</td><td>32</td></tr>
<tr><td>14</td><td></td><td>30</td><td></td><td>5,0</td><td>7,1</td><td>7,8</td><td>9,5</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>32</td><td>36</td><td>43</td></tr>
<tr><td>15</td><td></td><td>40</td><td></td><td>5,9</td><td>8,4</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>22</td><td>26</td><td>30</td><td>34</td><td>38</td><td>47</td></tr>
<tr><td>16</td><td>45</td><td>20</td><td>2</td><td>4,7</td><td>6,4</td><td>8,2</td><td>8,6</td><td>10</td><td>12</td><td>14</td><td>16</td><td>19</td><td>21</td><td>24</td><td>27</td><td>33</td></tr>
<tr><td>17</td><td></td><td>30</td><td></td><td>5,2</td><td>7,3</td><td>9,0</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>32</td><td>36</td><td>43</td></tr>
<tr><td>18</td><td></td><td>40</td><td></td><td>5,9</td><td>8,7</td><td>10</td><td>12</td><td>14</td><td>16</td><td>19</td><td>23</td><td>27</td><td>31</td><td>35</td><td>39</td><td>48</td></tr>
<tr><td>19</td><td></td><td>50</td><td></td><td>9,0</td><td>12</td><td>14</td><td>17</td><td>20</td><td>23</td><td>27</td><td>33</td><td>39</td><td>45</td><td>51</td><td>57</td><td>69</td></tr>
<tr><td>20</td><td>50</td><td>30</td><td>2</td><td>5,9</td><td>8,7</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>22</td><td>26</td><td>30</td><td>34</td><td>38</td><td>47</td></tr>
<tr><td>21</td><td></td><td>40</td><td></td><td>7,3</td><td>10</td><td>12</td><td>15</td><td>17</td><td>20</td><td>23</td><td>28</td><td>33</td><td>38</td><td>43</td><td>48</td><td>56</td></tr>
<tr><td>22</td><td></td><td>50</td><td></td><td>10</td><td>16</td><td>19</td><td>22</td><td>26</td><td>30</td><td>35</td><td>42</td><td>49</td><td>56</td><td>63</td><td>70</td><td>85</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="10">Предела прочности Предел прочности сигма , МПа обрабатываемого в</td><td colspan="7">до 590 590...740 св. 740</td></tr>
<tr><td colspan="10">Коэффициент К пп</td><td colspan="7">0,9 1,0 1,2</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="8%"><col width="9%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="18">Неполное штучное время Горизонтально- и вертикально- Фрезерование пазов, Rz 40...Rz 20; фрезерные станки 11 квалитет</td></tr>
<tr><td colspan="18">Медные сплавы, НВ = 980...1370 МПа Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="18">Карта 25</td></tr>
<tr><td colspan="18">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина</td><td rowspan="3">Глубина паза, Н, мм, до</td><td rowspan="3">Число рабочих ходов, i</td><td colspan="14">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>паза, В,</td><td>25</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td colspan="2">400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>мм, до</td><td colspan="14">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>25</td><td>10</td><td>1</td><td>1,8</td><td>2,2</td><td>2,3</td><td>2,4</td><td>2,5</td><td>3,0</td><td>3,3</td><td colspan="2">3,5</td><td>4,0</td><td>4,5</td><td>4,8</td><td>5,2</td><td>6,0</td></tr>
<tr><td>2</td><td rowspan="2"></td><td>15</td><td></td><td>2,0</td><td>2,3</td><td>2,4</td><td>2,5</td><td>2,8</td><td>3,3</td><td>3,5</td><td colspan="2">3,8</td><td>4,5</td><td>5,0</td><td>5,6</td><td>6,2</td><td>6,9</td></tr>
<tr><td>3</td><td>20</td><td>2</td><td>3,0</td><td>3,8</td><td>4,0</td><td>4,3</td><td>4,5</td><td>5,3</td><td>5,7</td><td colspan="2">6,2</td><td>7,0</td><td>7,7</td><td>8,5</td><td>9,0</td><td>10</td></tr>
<tr><td>4</td><td></td><td>30</td><td></td><td>3,2</td><td>4,0</td><td>4,3</td><td>4,5</td><td>5,0</td><td>6,0</td><td>6,5</td><td colspan="2">7,0</td><td>8,2</td><td>9,0</td><td>10</td><td>11</td><td>12</td></tr>
<tr><td>5</td><td>28</td><td>10</td><td>1</td><td>1,8</td><td>2,2</td><td>2,3</td><td>2,4</td><td>2,7</td><td>3,2</td><td>3,5</td><td colspan="2">3,6</td><td>4,3</td><td>4,7</td><td>5,3</td><td>5,8</td><td>6,5</td></tr>
<tr><td>6</td><td rowspan="2"></td><td>15</td><td></td><td>2,1</td><td>2,4</td><td>2,5</td><td>3,0</td><td>3,3</td><td>4,0</td><td>4,3</td><td colspan="2">4,8</td><td>5,8</td><td>6,4</td><td>7,4</td><td>8,2</td><td>9,5</td></tr>
<tr><td>7</td><td>20</td><td>2</td><td>3,0</td><td>3,8</td><td>4,0</td><td>4,5</td><td>5,0</td><td>5,7</td><td>6,2</td><td colspan="2">6,5</td><td>7,7</td><td>8,5</td><td>9,5</td><td>10</td><td>12</td></tr>
<tr><td>8</td><td></td><td>30</td><td></td><td>3,4</td><td>4,5</td><td>4,6</td><td>5,4</td><td>5,8</td><td>7,0</td><td>7,7</td><td colspan="2">8,6</td><td>10</td><td>12</td><td>14</td><td>15</td><td>17</td></tr>
<tr><td>9</td><td>32</td><td>10</td><td>1</td><td>2,0</td><td>2,4</td><td>2,5</td><td>2,7</td><td>3,0</td><td>3,5</td><td>3,8</td><td colspan="2">4,0</td><td>4,7</td><td>5,3</td><td>6,2</td><td>6,6</td><td>7,5</td></tr>
<tr><td>10</td><td rowspan="2"></td><td>15</td><td></td><td>2,2</td><td>2,5</td><td>2,7</td><td>3,0</td><td>3,3</td><td>4,0</td><td>4,4</td><td colspan="2">5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,3</td><td>9,5</td></tr>
<tr><td>11</td><td>20</td><td>2</td><td>3,2</td><td>4,3</td><td>4,5</td><td>5,0</td><td>5,3</td><td>6,4</td><td>6,8</td><td colspan="2">7,2</td><td>8,5</td><td>9,5</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>12</td><td></td><td>30</td><td></td><td>3,4</td><td>4,5</td><td>5,0</td><td>5,5</td><td>5,9</td><td>7,2</td><td>7,8</td><td colspan="2">9,0</td><td>10</td><td>12</td><td>14</td><td>15</td><td>17</td></tr>
<tr><td>13</td><td>36</td><td>20</td><td>2</td><td>3,3</td><td>4,4</td><td>4,6</td><td>5,2</td><td>5,6</td><td>6,5</td><td>7,0</td><td colspan="2">7,8</td><td>9,0</td><td>10</td><td>12</td><td>13</td><td>15</td></tr>
<tr><td>14</td><td></td><td>30</td><td></td><td>3,6</td><td>4,7</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,2</td><td>7,8</td><td colspan="2">9,0</td><td>10</td><td>12</td><td>13</td><td>15</td><td>17</td></tr>
<tr><td>15</td><td></td><td>40</td><td></td><td>3,8</td><td>5,0</td><td>5,6</td><td>6,2</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10</td><td>12</td><td>13</td><td>15</td><td>16</td><td>18</td></tr>
<tr><td>16</td><td>45</td><td>20</td><td>2</td><td>3,6</td><td>4,7</td><td>5,0</td><td>5,6</td><td>6,2</td><td>7,3</td><td>7,8</td><td colspan="2">8,5</td><td>10</td><td>11</td><td>13</td><td>14</td><td>16</td></tr>
<tr><td>17</td><td></td><td>30</td><td></td><td>3,8</td><td>5,0</td><td>5,6</td><td>6,2</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10</td><td>12</td><td>13</td><td>15</td><td>16</td><td>18</td></tr>
<tr><td>18</td><td></td><td>40</td><td></td><td>4,2</td><td>5,2</td><td>6,2</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td><td colspan="2">12</td><td>14</td><td>15</td><td>17</td><td>19</td><td>23</td></tr>
<tr><td>19</td><td></td><td>50</td><td></td><td>4,5</td><td>6,5</td><td>7,1</td><td>8,4</td><td>9,0</td><td>11</td><td>12</td><td colspan="2">14</td><td>16</td><td>18</td><td>21</td><td>24</td><td>28</td></tr>
<tr><td>20</td><td>50</td><td>30</td><td>2</td><td>3,8</td><td>5,0</td><td>5,6</td><td>6,2</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10</td><td>12</td><td>13</td><td>15</td><td>16</td><td>18</td></tr>
<tr><td>21</td><td></td><td>40</td><td></td><td>4,5</td><td>6,5</td><td>7,0</td><td>8,4</td><td>9,0</td><td>11</td><td>12</td><td colspan="2">14</td><td>16</td><td>18</td><td>21</td><td>24</td><td>28</td></tr>
<tr><td>22</td><td></td><td>50</td><td></td><td>5,6</td><td>8,0</td><td>8,7</td><td>10</td><td>11</td><td>14</td><td>15</td><td colspan="2">17</td><td>20</td><td>23</td><td>26</td><td>29</td><td>36</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
<tr><td colspan="18">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="12">Твердости Твердость сплава, НВ, МПа 590...980 обрабатываемого Коэффициент К 0,7 сплава тв</td><td colspan="6">980...1370 1470...2450 1,0 1,20</td></tr>
</table>



```text
┌──────────────────────────────────┬────────────────────────────────┐
│      Неполное штучное время      │ Горизонтально- и шлицефрезерные│
│       Фрезерование шлицев        │             станки             │
│   по сплошному металлу, Ra 2,5   ├────────────────────────────────┤
│      Сталь конструкционная,      │   Фрезы дисковые модульные и   │
│     сигма  = 590...740 МПа       │    червячные из стали Р6М5     │
│          в                       ├────────────────────────────────┤
│                                  │            Карта 26            │
├──────────────────────────────────┴────────────────────────────────┤
│                       рисунок не приводится                       │
├───────────────────────────────────────────────────────────────────┤
│                  I. Горизонтально-фрезерные станки                │
│   Фрезерование шлицев дисковой модульной фрезой методом деления   │
├───┬───────┬───────────────────────────────────────────────────────┤
│N  │Ширина │               Длина шлицев, l, мм, до                 │
│по-│шлицев,├─────┬──────┬──────┬──────┬──────┬──────┬──────┬───────┤
│зи-│В, мм, │ 50  │ 100  │ 150  │ 200  │ 250  │ 300  │ 400  │  500  │
│ции│до     ├─────┴──────┴──────┴──────┴──────┴──────┴──────┴───────┤
│   │       │     Время на нарезание одного шлица, t  , мин.        │
│   │       │                                       нш              │
├───┼───────┼─────┬──────┬──────┬──────┬──────┬──────┬──────┬───────┤
│1  │6      │2,3  │2,6   │3,2   │3,4   │3,9   │4,4   │5,4   │6,0    │
│2  │8      │2,7  │3,4   │4,1   │4,8   │5,4   │6,0   │7,6   │9,0    │
│3  │10     │2,9  │3,6   │4,5   │5,3   │6,0   │7,0   │8,5   │10     │
│4  │12     │3,4  │4,7   │6,0   │7,0   │8,7   │10    │11    │14     │
│5  │14     │3,8  │5,4   │7,1   │7,6   │10    │11    │14    │17     │
│6  │16     │4,4  │7,1   │7,6   │9,5   │11    │13    │16    │19     │
│7  │18     │4,9  │7,1   │9,0   │11    │13    │15    │19    │23     │
│8  │20     │6,5  │7,6   │10    │12    │15    │17    │22    │26     │
├───┴───────┼─────┼──────┼──────┼──────┼──────┼──────┼──────┼───────┤
│Индекс     │  а  │  б   │  в   │  г   │  д   │  е   │  ж   │   з   │
├───────────┴─────┴──────┴──────┴──────┴──────┴──────┴──────┴───────┤
│                     II. Шлицефрезерные станки                     │
│                Фрезерование шлицев червячными фрезами             │
├───┬───────┬───────┬───────────────────────────────────────────────┤
│N  │Диаметр│Ширина │  Длина обрабатываемой поверхности, l, мм, до  │
│по-│ вала, │шлицев,├───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┤
│зи-│ D, мм │В, мм, │50 │75 │100│125│150│175│200│250│300│350│400│500│
│ции│       │  до   ├───┴───┴───┴───┴───┴───┴───┴───┴───┴───┴───┴───┤
│   │       │       │          Время на деталь, t  , мин.           │
│   │       │       │                            нш                 │
├───┼───────┼───────┼───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┤
│9  │14 - 28│6      │8,5│13 │17 │21 │25 │29 │33 │39 │45 │51 │57 │68 │
│10 │30 - 52│8 - 10 │13 │20 │27 │33 │39 │45 │51 │62 │72 │83 │94 │114│
│11 │54 - 70│12 - 14│24 │35 │47 │58 │70 │81 │92 │107│127│145│168│200│
│12 │72 - 82│16     │34 │55 │71 │85 │99 │108│129│151│180│209│243│273│
│13 │90 -   │18     │37 │55 │73 │91 │109│127│145│168│204│238│273│300│
│   │100    │       │   │   │   │   │   │   │   │   │   │   │   │   │
│14 │105 -  │20     │44 │71 │90 │109│127│140│164│191│227│267│304│359│
│   │125    │       │   │   │   │   │   │   │   │   │   │   │   │   │
├───┴───────┴───────┼───┼───┼───┼───┼───┼───┼───┼───┼───┼───┼───┼───┤
│Индекс             │ а │ б │ в │ г │ д │ е │ ж │ з │ и │ к │ л │ м │
├───────────────────┴───┴───┴───┴───┴───┴───┴───┴───┴───┴───┴───┴───┤
│Поправочные коэффициенты на время обработки для измененных условий │
│работы в зависимости от:                                           │
├─────────────────┬──────────────────┬─────────┬───────────┬────────┤
│Предела прочности│Предел прочности, │до 590   │590...740  │св. 740 │
│обрабатываемого  │сигма , МПа       │         │           │        │
│материала        │     в            │         │           │        │
│                 │Коэффициент К     │0,9      │1,0        │1,2     │
│                 │             пп   │         │           │        │
└─────────────────┴──────────────────┴─────────┴───────────┴────────┘
```



<table>
<colgroup><col width="6%"><col width="18%"><col width="14%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="11">Неполное штучное время Горизонтально- и вертикально- Отрезка фрезерные станки Чугун серый, НВ = 1760...2150 МПа</td></tr>
<tr><td colspan="11">Фрезы отрезные из стали Р6М5</td></tr>
<tr><td colspan="11">Карта 27 лист 1</td></tr>
<tr><td colspan="11">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фрезы, D, мм, и число</td><td rowspan="3">Глубина резания, t, мм</td><td colspan="8">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">зубьев, z</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td></tr>
<tr><td colspan="8">Время, t , мин. нш</td></tr>
<tr><td>1</td><td>63/100...80</td><td>6</td><td>1,8</td><td>2,0</td><td>2,3</td><td>2,7</td><td>3,1</td><td>3,5</td><td>4,0</td><td>4,8</td></tr>
<tr><td>2</td><td>63/64...32</td><td>10</td><td>2,0</td><td>2,2</td><td>2,5</td><td>2,9</td><td>3,5</td><td>4,0</td><td>4,7</td><td>5,4</td></tr>
<tr><td>3</td><td>63/24...16</td><td>10</td><td>2,2</td><td>2,6</td><td>3,0</td><td>3,5</td><td>4,3</td><td>5,0</td><td>5,8</td><td>7,0</td></tr>
<tr><td>4</td><td></td><td>15</td><td>2,7</td><td>3,2</td><td>4,0</td><td>4,8</td><td>5,8</td><td>6,9</td><td>8,2</td><td>9,5</td></tr>
<tr><td>5</td><td>80/64...32</td><td>10</td><td>1,8</td><td>2,0</td><td>2,3</td><td>2,6</td><td>3,0</td><td>3,4</td><td>3,8</td><td>4,5</td></tr>
<tr><td>6</td><td></td><td>15</td><td>2,0</td><td>2,3</td><td>2,7</td><td>3,1</td><td>3,6</td><td>4,3</td><td>4,8</td><td>6,0</td></tr>
<tr><td>7</td><td>80/24...14</td><td>10</td><td>2,7</td><td>3,1</td><td>3,7</td><td>4,4</td><td>5,3</td><td>6,0</td><td>7,1</td><td>8,7</td></tr>
<tr><td>8</td><td></td><td>15</td><td>3,2</td><td>3,8</td><td>4,7</td><td>5,9</td><td>7,2</td><td>8,2</td><td>10</td><td>12</td></tr>
<tr><td>9</td><td>100/80...40</td><td>15</td><td>1,9</td><td>2,2</td><td>2,4</td><td>2,9</td><td>3,4</td><td>3,6</td><td>4,3</td><td>5,0</td></tr>
<tr><td>10</td><td></td><td>25</td><td>2,1</td><td>2,4</td><td>2,8</td><td>3,2</td><td>3,8</td><td>4,3</td><td>4,8</td><td>6,0</td></tr>
<tr><td>11</td><td>100/32...16</td><td>15</td><td>2,7</td><td>3,1</td><td>3,7</td><td>4,4</td><td>5,7</td><td>6,0</td><td>7,1</td><td>8,0</td></tr>
<tr><td>12</td><td></td><td>25</td><td>3,0</td><td>4,0</td><td>5,1</td><td>6,3</td><td>7,5</td><td>9,0</td><td>10</td><td>11</td></tr>
<tr><td>13</td><td>125/80...48</td><td>15</td><td>2,3</td><td>2,9</td><td>3,1</td><td>3,8</td><td>4,6</td><td>5,2</td><td>6,0</td><td>7,3</td></tr>
<tr><td>14</td><td></td><td>25</td><td>3,1</td><td>3,7</td><td>4,4</td><td>5,2</td><td>6,4</td><td>7,5</td><td>8,6</td><td>10</td></tr>
<tr><td>15</td><td>125/32...18</td><td>15</td><td>3,3</td><td>4,0</td><td>4,8</td><td>5,6</td><td>7,0</td><td>8,0</td><td>9,0</td><td>11</td></tr>
<tr><td>16</td><td></td><td>25</td><td>3,6</td><td>4,5</td><td>5,5</td><td>6,5</td><td>7,8</td><td>8,7</td><td>10</td><td>13</td></tr>
<tr><td>17</td><td>160/80...48</td><td>20</td><td>2,4</td><td>3,0</td><td>3,4</td><td>4,0</td><td>5,0</td><td>5,8</td><td>6,5</td><td>7,7</td></tr>
<tr><td>18</td><td></td><td>30</td><td>3,3</td><td>4,0</td><td>4,6</td><td>5,5</td><td>6,6</td><td>7,8</td><td>8,8</td><td>10</td></tr>
<tr><td>19</td><td></td><td>45</td><td>3,9</td><td>4,5</td><td>5,8</td><td>6,5</td><td>8,1</td><td>9,0</td><td>11</td><td>14</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="18%"><col width="14%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="11">Неполное штучное время Горизонтально- и вертикально- Отрезка фрезерные станки Чугун серый, НВ = 1760...2150 МПа</td></tr>
<tr><td colspan="11">Фрезы отрезные из стали Р6М5</td></tr>
<tr><td colspan="11">Карта 27 лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фрезы, D, мм, и число</td><td rowspan="3">Глубина резания, t, мм</td><td colspan="8">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">зубьев, z</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td></tr>
<tr><td colspan="8">Время, t , мин. нш</td></tr>
<tr><td>20</td><td>160/40...20</td><td>20</td><td>3,8</td><td>4,2</td><td>5,6</td><td>6,3</td><td>7,7</td><td>8,5</td><td>10</td><td>13</td></tr>
<tr><td>21</td><td></td><td>30</td><td>4,5</td><td>5,2</td><td>6,5</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>16</td></tr>
<tr><td>22</td><td></td><td>45</td><td>5,5</td><td>6,3</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>18</td></tr>
<tr><td>23</td><td>200/100...</td><td>20</td><td>3,2</td><td>3,8</td><td>4,4</td><td>5,0</td><td>5,8</td><td>6,7</td><td>7,7</td><td>9,5</td></tr>
<tr><td>24</td><td>48</td><td>30</td><td>3,3</td><td>4,0</td><td>4,6</td><td>5,5</td><td>6,6</td><td>7,3</td><td>8,7</td><td>11</td></tr>
<tr><td>25</td><td></td><td>45</td><td>4,2</td><td>4,6</td><td>5,8</td><td>6,9</td><td>8,2</td><td>9,0</td><td>11</td><td>13</td></tr>
<tr><td>26</td><td></td><td>70</td><td>6,3</td><td>7,0</td><td>8,7</td><td>10</td><td>12</td><td>14</td><td>17</td><td>21</td></tr>
<tr><td>27</td><td>200/40...20</td><td>20</td><td>4,2</td><td>4,6</td><td>5,8</td><td>7,0</td><td>8,2</td><td>9,0</td><td>11</td><td>13</td></tr>
<tr><td>28</td><td></td><td>30</td><td>4,5</td><td>5,8</td><td>6,6</td><td>7,7</td><td>9,5</td><td>11</td><td>13</td><td>16</td></tr>
<tr><td>29</td><td></td><td>45</td><td>8,1</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td><td>24</td></tr>
<tr><td>30</td><td></td><td>70</td><td>9,5</td><td>11</td><td>12</td><td>16</td><td>19</td><td>22</td><td>26</td><td>30</td></tr>
<tr><td>31</td><td>250/100...</td><td>30</td><td>4,4</td><td>4,8</td><td>6,0</td><td>7,3</td><td>8,5</td><td>9,4</td><td>11</td><td>14</td></tr>
<tr><td>32</td><td>64</td><td>50</td><td>7,0</td><td>7,8</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>33</td><td></td><td>80</td><td>8,1</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>20</td><td>24</td></tr>
<tr><td>34</td><td>250/40...22</td><td>30</td><td>6,2</td><td>6,9</td><td>8,5</td><td>10</td><td>12</td><td>14</td><td>17</td><td>20</td></tr>
<tr><td>35</td><td></td><td>50</td><td>8,3</td><td>9,5</td><td>11</td><td>14</td><td>16</td><td>18</td><td>22</td><td>26</td></tr>
<tr><td>36</td><td></td><td>80</td><td>10</td><td>12</td><td>14</td><td>17</td><td>20</td><td>24</td><td>28</td><td>33</td></tr>
<tr><td>37</td><td>315/100...</td><td>50</td><td>7,5</td><td>8,3</td><td>9,0</td><td>11</td><td>14</td><td>16</td><td>18</td><td>21</td></tr>
<tr><td>38</td><td>80</td><td>100</td><td>9,0</td><td>10</td><td>12</td><td>15</td><td>17</td><td>19</td><td>23</td><td>27</td></tr>
<tr><td>39</td><td>315/48...40</td><td>50</td><td>8,0</td><td>9,0</td><td>10</td><td>13</td><td>15</td><td>17</td><td>19</td><td>23</td></tr>
<tr><td>40</td><td></td><td>100</td><td>12</td><td>15</td><td>17</td><td>20</td><td>23</td><td>27</td><td>31</td><td>36</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
<tr><td colspan="11">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2">Твердости обрабатываемого материала</td><td colspan="9">Твердость чугуна, до 2150 св. 2150 НВ, МПа Коэффициент К 1,0 1,2 тв</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="15%"><col width="8%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="7" rowspan="3">Неполное штучное время Отрезка Сталь конструкционная, сигма = 590...740 МПа в</td><td colspan="8">Горизонтально- и вертикальнофрезерные станки</td></tr>
<tr><td colspan="8">Фрезы отрезные из стали Р6М5</td></tr>
<tr><td colspan="8">Карта 28 лист 1</td></tr>
<tr><td colspan="15">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фрезы, D,</td><td>Глубина</td><td colspan="12">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>мм, и число зубьев,</td><td>резания,</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>z</td><td>t, мм</td><td colspan="12">Время, t , мин. нш</td></tr>
<tr><td>1</td><td>63/160... 80</td><td>6</td><td>2,0</td><td>2,3</td><td>2,7</td><td>3,1</td><td>3,7</td><td>4,5</td><td>5,2</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10</td></tr>
<tr><td>2</td><td>63/64...</td><td>10</td><td>2,2</td><td>2,6</td><td>3,0</td><td>3,5</td><td>4,3</td><td>5,2</td><td>6,2</td><td>7,4</td><td>8,6</td><td>9,8</td><td>11</td><td>13</td></tr>
<tr><td>3</td><td>32</td><td>15</td><td>2,5</td><td>3,0</td><td>3,8</td><td>4,5</td><td>5,2</td><td>6,2</td><td>7,4</td><td>8,6</td><td>9,2</td><td>10</td><td>12</td><td>15</td></tr>
<tr><td>4</td><td>63/24...</td><td>10</td><td>2,4</td><td>2,8</td><td>3,4</td><td>4,2</td><td>4,8</td><td>5,8</td><td>7,0</td><td>8,0</td><td>9,0</td><td>9,8</td><td>11</td><td>14</td></tr>
<tr><td>5</td><td>14</td><td>15</td><td>2,6</td><td>3,2</td><td>3,8</td><td>4,8</td><td>5,5</td><td>6,6</td><td>8,0</td><td>9,0</td><td>10</td><td>12</td><td>14</td><td>16</td></tr>
<tr><td>6</td><td>80/64...</td><td>10</td><td>2,8</td><td>3,4</td><td>4,0</td><td>5,2</td><td>6,6</td><td>8,0</td><td>9,0</td><td>10</td><td>11</td><td>13</td><td>15</td><td>17</td></tr>
<tr><td>7</td><td>32</td><td>15</td><td>2,9</td><td>3,7</td><td>4,4</td><td>5,8</td><td>7,6</td><td>8,5</td><td>9,5</td><td>11</td><td>13</td><td>15</td><td>17</td><td>19</td></tr>
<tr><td>8</td><td>80/24...</td><td>10</td><td>3,0</td><td>4,0</td><td>5,0</td><td>6,2</td><td>7,8</td><td>8,7</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>21</td></tr>
<tr><td>9</td><td>14</td><td>15</td><td>3,3</td><td>4,1</td><td>5,1</td><td>6,3</td><td>8,0</td><td>8,9</td><td>11</td><td>12</td><td>15</td><td>17</td><td>19</td><td>24</td></tr>
<tr><td>10</td><td>100/80...</td><td>15</td><td>3,5</td><td>4,3</td><td>5,2</td><td>6,3</td><td>7,8</td><td>9,2</td><td>11</td><td>12</td><td>15</td><td>18</td><td>21</td><td>26</td></tr>
<tr><td>11</td><td>40</td><td>25</td><td>2,8</td><td>4,5</td><td>5,3</td><td>6,4</td><td>8,0</td><td>9,4</td><td>12</td><td>13</td><td>16</td><td>20</td><td>24</td><td>30</td></tr>
<tr><td>12</td><td>100/32...</td><td>15</td><td>3,7</td><td>4,2</td><td>5,1</td><td>6,5</td><td>7,6</td><td>8,5</td><td>11</td><td>13</td><td>15</td><td>19</td><td>23</td><td>29</td></tr>
<tr><td>13</td><td>16</td><td>25</td><td>4,0</td><td>4,7</td><td>5,6</td><td>6,7</td><td>8,2</td><td>9,6</td><td>13</td><td>14</td><td>17</td><td>21</td><td>25</td><td>31</td></tr>
<tr><td>14</td><td>125/80...</td><td>15</td><td>3,8</td><td>4,5</td><td>5,2</td><td>6,4</td><td>8,0</td><td>9,4</td><td>11</td><td>13</td><td>16</td><td>19</td><td>23</td><td>30</td></tr>
<tr><td>15</td><td>48</td><td>25</td><td>4,3</td><td>5,0</td><td>6,4</td><td>7,7</td><td>9,0</td><td>11</td><td>13</td><td>16</td><td>19</td><td>22</td><td>26</td><td>33</td></tr>
<tr><td>16</td><td>125/32...</td><td>15</td><td>4,2</td><td>4,8</td><td>5,7</td><td>6,6</td><td>8,5</td><td>10</td><td>12</td><td>14</td><td>17</td><td>20</td><td>24</td><td>31</td></tr>
<tr><td>17</td><td>18</td><td>25</td><td>4,5</td><td>5,2</td><td>6,8</td><td>8,0</td><td>9,4</td><td>11</td><td>13</td><td>16</td><td>20</td><td>23</td><td>27</td><td>35</td></tr>
<tr><td>18</td><td>160/80...</td><td>20</td><td>4,4</td><td>5,0</td><td>5,9</td><td>7,0</td><td>8,2</td><td>11</td><td>13</td><td>15</td><td>18</td><td>21</td><td>25</td><td>32</td></tr>
<tr><td>19</td><td>48</td><td>30</td><td>4,8</td><td>5,4</td><td>6,2</td><td>8,2</td><td>9,5</td><td>11</td><td>14</td><td>17</td><td>21</td><td>25</td><td>31</td><td>38</td></tr>
<tr><td>20</td><td></td><td>45</td><td>5,3</td><td>6,1</td><td>7,0</td><td>8,6</td><td>11</td><td>12</td><td>15</td><td>18</td><td>22</td><td>26</td><td>33</td><td>40</td></tr>
<tr><td>21</td><td>160/32...</td><td>20</td><td>4,6</td><td>5,2</td><td>5,8</td><td>6,5</td><td>8,6</td><td>11</td><td>13</td><td>16</td><td>19</td><td>23</td><td>28</td><td>36</td></tr>
<tr><td>22</td><td>20</td><td>30</td><td>5,0</td><td>5,6</td><td>6,5</td><td>7,5</td><td>10</td><td>12</td><td>15</td><td>18</td><td>22</td><td>25</td><td>30</td><td>33</td></tr>
<tr><td>23</td><td></td><td>45</td><td>5,6</td><td>6,2</td><td>7,4</td><td>9,8</td><td>12</td><td>14</td><td>16</td><td>19</td><td>24</td><td>28</td><td>34</td><td>45</td></tr>
<tr><td>24</td><td>200/100...</td><td>20</td><td>5,0</td><td>5,6</td><td>6,5</td><td>7,5</td><td>10</td><td>12</td><td>15</td><td>17</td><td>22</td><td>25</td><td>30</td><td>38</td></tr>
<tr><td>25</td><td>48</td><td>30</td><td>5,7</td><td>6,4</td><td>8,0</td><td>10</td><td>12</td><td>15</td><td>18</td><td>21</td><td>25</td><td>29</td><td>35</td><td>43</td></tr>
<tr><td>26</td><td></td><td>45</td><td>6,2</td><td>7,2</td><td>8,5</td><td>11</td><td>13</td><td>16</td><td>19</td><td>23</td><td>27</td><td>31</td><td>37</td><td>45</td></tr>
<tr><td>27</td><td></td><td>70</td><td>7,0</td><td>8,3</td><td>9,4</td><td>11</td><td>14</td><td>17</td><td>21</td><td>25</td><td>29</td><td>33</td><td>39</td><td>47</td></tr>
<tr><td>28</td><td>200/32...</td><td>20</td><td>5,8</td><td>6,8</td><td>8,3</td><td>10</td><td>12</td><td>15</td><td>18</td><td>22</td><td>26</td><td>30</td><td>36</td><td>44</td></tr>
<tr><td>29</td><td>20</td><td>30</td><td>6,3</td><td>7,4</td><td>8,8</td><td>11</td><td>13</td><td>16</td><td>20</td><td>24</td><td>28</td><td>32</td><td>38</td><td>46</td></tr>
<tr><td>30</td><td></td><td>45</td><td>7,0</td><td>8,3</td><td>9,4</td><td>11</td><td>14</td><td>17</td><td>21</td><td>25</td><td>29</td><td>33</td><td>39</td><td>47</td></tr>
<tr><td>31</td><td></td><td>70</td><td>7,7</td><td>9,6</td><td>10</td><td>12</td><td>15</td><td>18</td><td>22</td><td>26</td><td>30</td><td>35</td><td>41</td><td>49</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="15%"><col width="4%"><col width="4%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="17">Неполное штучное время Горизонтально- и вертикально- Отрезка фрезерные станки</td></tr>
<tr><td colspan="17">сигма = 590...740 МПа Фрезы отрезные из стали Р6М3, Р6М5</td></tr>
<tr><td colspan="17">Карта 28 лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фрезы, D,</td><td colspan="2">Глубина</td><td colspan="13">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>мм, и число зубьев,</td><td colspan="2">резания,</td><td>50</td><td>100</td><td>150</td><td>200</td><td colspan="2">250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>z</td><td colspan="2">t, мм</td><td colspan="13">Время, t , мин. нш</td></tr>
<tr><td>32</td><td>250/100...</td><td colspan="2">30</td><td>7,2</td><td>8,5</td><td>9,6</td><td>11</td><td colspan="2">14</td><td>17</td><td>22</td><td>26</td><td>30</td><td>34</td><td>40</td><td>47</td></tr>
<tr><td>33</td><td>64</td><td colspan="2">50</td><td>7,8</td><td>9,0</td><td>10</td><td>12</td><td colspan="2">16</td><td>18</td><td>23</td><td>27</td><td>29</td><td>33</td><td>39</td><td>48</td></tr>
<tr><td>34</td><td></td><td colspan="2">80</td><td>8,5</td><td>10</td><td>12</td><td>14</td><td colspan="2">17</td><td>20</td><td>24</td><td>28</td><td>33</td><td>36</td><td>43</td><td>45</td></tr>
<tr><td>35</td><td>250/40...</td><td colspan="2">30</td><td>7,8</td><td>9,0</td><td>10</td><td>12</td><td colspan="2">16</td><td>18</td><td>23</td><td>27</td><td>29</td><td>33</td><td>39</td><td>48</td></tr>
<tr><td>36</td><td>22</td><td colspan="2">50</td><td>8,3</td><td>9,8</td><td>11</td><td>13</td><td colspan="2">16</td><td>19</td><td>20</td><td>24</td><td>27</td><td>31</td><td>42</td><td>52</td></tr>
<tr><td>37</td><td></td><td colspan="2">80</td><td>9,0</td><td>11</td><td>13</td><td>16</td><td colspan="2">18</td><td>22</td><td>26</td><td>31</td><td>36</td><td>41</td><td>47</td><td>54</td></tr>
<tr><td>38</td><td>315/100...</td><td colspan="2">50</td><td>8,5</td><td>10</td><td>12</td><td>14</td><td colspan="2">17</td><td>20</td><td>24</td><td>28</td><td>33</td><td>36</td><td>43</td><td>52</td></tr>
<tr><td>39</td><td>80</td><td colspan="2">100</td><td>9,2</td><td>11,6</td><td>13,6</td><td>16,5</td><td colspan="2">19</td><td>22</td><td>27</td><td>32</td><td>37</td><td>42</td><td>48</td><td>55</td></tr>
<tr><td>40</td><td>315/48...</td><td colspan="2">50</td><td>9,0</td><td>11</td><td>13</td><td>16</td><td colspan="2">18</td><td>22</td><td>26</td><td>31</td><td>36</td><td>41</td><td>47</td><td>54</td></tr>
<tr><td>41</td><td>40</td><td colspan="2">100</td><td>10</td><td>12</td><td>14</td><td>17</td><td colspan="2">20</td><td>23</td><td>28</td><td>33</td><td>38</td><td>43</td><td>49</td><td>57</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">Предела прочности обрабатываемого материала</td><td colspan="6">Предел прочности стали сигма , МПа в Коэффициент К пп</td><td colspan="3">до 590 0,9</td><td colspan="3">590...740 1,0</td><td colspan="2">св. 740 1,2</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="18%"><col width="14%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="3%"><col width="5%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="5" rowspan="3">Неполное штучное время Отрезка Медные сплавы, НВ = 980...1370 МПа</td><td colspan="7">Горизонтально- и вертикальнофрезерные станки</td></tr>
<tr><td colspan="7">Фрезы отрезные из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 29</td><td colspan="3">лист 1</td></tr>
<tr><td colspan="12">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фрезы, D, мм, и число</td><td rowspan="3">Глубина резания, t, мм</td><td colspan="9">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">зубьев, z</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td colspan="2">300</td><td>400</td><td>500</td></tr>
<tr><td colspan="9">Время, t , мин. нш</td></tr>
<tr><td>1</td><td>63/100...32</td><td>10</td><td>1,6</td><td>1,7</td><td>1,9</td><td>2,0</td><td>2,5</td><td colspan="2">2,7</td><td>3,0</td><td>3,6</td></tr>
<tr><td>2</td><td>63/24...16</td><td>15</td><td>1,9</td><td>2,1</td><td>2,4</td><td>2,7</td><td>3,4</td><td colspan="2">3,7</td><td>4,3</td><td>5,2</td></tr>
<tr><td>3</td><td>80/64...32</td><td>10</td><td>1,5</td><td>1,6</td><td>1,7</td><td>1,8</td><td>2,2</td><td colspan="2">2,4</td><td>2,6</td><td>2,9</td></tr>
<tr><td>4</td><td></td><td>15</td><td>1,6</td><td>1,8</td><td>1,9</td><td>2,1</td><td>2,4</td><td colspan="2">2,6</td><td>2,9</td><td>3,5</td></tr>
<tr><td>5</td><td>80/24...14</td><td>10</td><td>1,8</td><td>2,0</td><td>2,2</td><td>2,6</td><td>3,1</td><td colspan="2">3,6</td><td>3,8</td><td>4,5</td></tr>
<tr><td>6</td><td></td><td>15</td><td>2,1</td><td>2,4</td><td>2,7</td><td>3,2</td><td>3,9</td><td colspan="2">4,3</td><td>5,0</td><td>6,2</td></tr>
<tr><td>7</td><td>100/80...40</td><td>15</td><td>1,5</td><td>1,6</td><td>1,8</td><td>1,9</td><td>2,2</td><td colspan="2">2,4</td><td>2,7</td><td>3,0</td></tr>
<tr><td>8</td><td></td><td>25</td><td>1,6</td><td>1,8</td><td>2,0</td><td>2,1</td><td>2,5</td><td colspan="2">2,7</td><td>3,1</td><td>3,6</td></tr>
<tr><td>9</td><td>100/32...16</td><td>15</td><td>1,8</td><td>2,0</td><td>2,2</td><td>2,5</td><td>2,8</td><td colspan="2">3,2</td><td>3,6</td><td>4,0</td></tr>
<tr><td>10</td><td></td><td>25</td><td>2,0</td><td>2,2</td><td>2,5</td><td>2,9</td><td>3,5</td><td colspan="2">4,1</td><td>4,6</td><td>5,3</td></tr>
<tr><td>11</td><td>125/80...48</td><td>15</td><td>1,6</td><td>1,8</td><td>2,0</td><td>2,1</td><td>2,5</td><td colspan="2">2,7</td><td>3,1</td><td>3,6</td></tr>
<tr><td>12</td><td></td><td>25</td><td>2,1</td><td>2,4</td><td>2,7</td><td>3,0</td><td>3,3</td><td colspan="2">3,7</td><td>4,2</td><td>4,8</td></tr>
<tr><td>13</td><td>125/32...18</td><td>15</td><td>2,2</td><td>2,5</td><td>2,8</td><td>3,1</td><td>3,5</td><td colspan="2">4,0</td><td>4,6</td><td>5,3</td></tr>
<tr><td>14</td><td></td><td>25</td><td>2,5</td><td>2,9</td><td>3,3</td><td>4,0</td><td>4,7</td><td colspan="2">5,5</td><td>6,3</td><td>7,5</td></tr>
<tr><td>15</td><td>160/80...48</td><td>20</td><td>1,8</td><td>2,0</td><td>2,2</td><td>2,5</td><td>2,8</td><td colspan="2">3,1</td><td>3,6</td><td>4,2</td></tr>
<tr><td>16</td><td></td><td>30</td><td>2,1</td><td>2,4</td><td>2,7</td><td>3,1</td><td>3,5</td><td colspan="2">4,0</td><td>4,7</td><td>5,4</td></tr>
<tr><td>17</td><td></td><td>45</td><td>2,7</td><td>3,1</td><td>3,6</td><td>4,3</td><td>5,0</td><td colspan="2">5,8</td><td>6,7</td><td>7,8</td></tr>
<tr><td>18</td><td>160/40...20</td><td>20</td><td>2,0</td><td>2,1</td><td>2,4</td><td>2,7</td><td>3,1</td><td colspan="2">3,5</td><td>4,0</td><td>4,7</td></tr>
<tr><td>19</td><td></td><td>30</td><td>2,4</td><td>2,7</td><td>3,1</td><td>3,5</td><td>4,0</td><td colspan="2">4,7</td><td>5,5</td><td>6,4</td></tr>
<tr><td>20</td><td></td><td>45</td><td>3,1</td><td>3,5</td><td>4,1</td><td>4,8</td><td>5,6</td><td colspan="2">6,4</td><td>7,5</td><td>9,0</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="15%"><col width="3%"><col width="14%"><col width="8%"><col width="3%"><col width="5%"><col width="8%"><col width="3%"><col width="5%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="3">Неполное штучное время Отрезка Медные сплавы, НВ = 980...1370 МПа</td><td colspan="8">Горизонтально- и вертикальнофрезерные станки</td></tr>
<tr><td colspan="8">Фрезы отрезные из стали Р6М5</td></tr>
<tr><td colspan="8">Карта 29 лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2">Диаметр фрезы, D, мм, и число</td><td rowspan="3">Глубина резания, t, мм</td><td colspan="11">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td colspan="2" rowspan="2">зубьев, z</td><td>50</td><td colspan="2">100</td><td>150</td><td colspan="2">200</td><td>250</td><td colspan="2">300</td><td>400</td><td>500</td></tr>
<tr><td colspan="11">Время, t , мин. нш</td></tr>
<tr><td>21</td><td colspan="2">200/100...</td><td>20</td><td>2,0</td><td colspan="2">2,2</td><td>2,5</td><td colspan="2">2,8</td><td>3,2</td><td colspan="2">3,6</td><td>4,0</td><td>4,7</td></tr>
<tr><td>22</td><td colspan="2">48</td><td>30</td><td>2,2</td><td colspan="2">2,5</td><td>2,8</td><td colspan="2">3,2</td><td>3,6</td><td colspan="2">4,0</td><td>4,5</td><td>5,4</td></tr>
<tr><td>23</td><td colspan="2"></td><td>45</td><td>2,8</td><td colspan="2">3,2</td><td>3,7</td><td colspan="2">4,3</td><td>5,1</td><td colspan="2">5,9</td><td>6,7</td><td>7,9</td></tr>
<tr><td>24</td><td colspan="2"></td><td>70</td><td>4,0</td><td colspan="2">4,5</td><td>5,2</td><td colspan="2">6,0</td><td>7,0</td><td colspan="2">8,2</td><td>9,5</td><td>11</td></tr>
<tr><td>25</td><td colspan="2">200/40...20</td><td>20</td><td>2,4</td><td colspan="2">2,7</td><td>3,1</td><td colspan="2">3,4</td><td>4,0</td><td colspan="2">4,6</td><td>5,2</td><td>6,4</td></tr>
<tr><td>26</td><td colspan="2"></td><td>30</td><td>2,7</td><td colspan="2">3,1</td><td>3,5</td><td colspan="2">4,0</td><td>4,8</td><td colspan="2">5,8</td><td>6,6</td><td>7,7</td></tr>
<tr><td>27</td><td colspan="2"></td><td>45</td><td>3,1</td><td colspan="2">3,5</td><td>4,3</td><td colspan="2">5,0</td><td>5,8</td><td colspan="2">6,6</td><td>7,7</td><td>9,5</td></tr>
<tr><td>28</td><td colspan="2"></td><td>70</td><td>4,6</td><td colspan="2">5,3</td><td>6,3</td><td colspan="2">7,4</td><td>8,6</td><td colspan="2">10</td><td>12</td><td>14</td></tr>
<tr><td>29</td><td colspan="2">250/100...</td><td>30</td><td>3,0</td><td colspan="2">3,7</td><td>4,5</td><td colspan="2">5,2</td><td>6,0</td><td colspan="2">7,0</td><td>8,0</td><td>9,5</td></tr>
<tr><td>30</td><td colspan="2">64</td><td>50</td><td>3,5</td><td colspan="2">4,3</td><td>5,2</td><td colspan="2">6,0</td><td>7,0</td><td colspan="2">8,0</td><td>9,5</td><td>11</td></tr>
<tr><td>31</td><td colspan="2"></td><td>80</td><td>4,3</td><td colspan="2">5,0</td><td>5,7</td><td colspan="2">6,4</td><td>7,5</td><td colspan="2">8,5</td><td>10</td><td>12</td></tr>
<tr><td>32</td><td colspan="2">250/40...22</td><td>30</td><td>4,0</td><td colspan="2">4,7</td><td>5,5</td><td colspan="2">6,3</td><td>7,3</td><td colspan="2">8,3</td><td>9,8</td><td>11</td></tr>
<tr><td>33</td><td colspan="2"></td><td>50</td><td>4,8</td><td colspan="2">5,4</td><td>6,4</td><td colspan="2">7,5</td><td>8,8</td><td colspan="2">10</td><td>12</td><td>14</td></tr>
<tr><td>34</td><td colspan="2"></td><td>80</td><td>5,5</td><td colspan="2">6,6</td><td>7,9</td><td colspan="2">9,5</td><td>11</td><td colspan="2">13</td><td>15</td><td>17</td></tr>
<tr><td>35</td><td colspan="2">315/100...</td><td>50</td><td>4,4</td><td colspan="2">5,2</td><td>6,0</td><td colspan="2">6,8</td><td>8,0</td><td colspan="2">9,0</td><td>10</td><td>12</td></tr>
<tr><td>36</td><td colspan="2">80</td><td>100</td><td>5,0</td><td colspan="2">5,7</td><td>6,4</td><td colspan="2">7,1</td><td>8,5</td><td colspan="2">9,5</td><td>11</td><td>13</td></tr>
<tr><td>37</td><td colspan="2">315/48...40</td><td>50</td><td>5,5</td><td colspan="2">6,3</td><td>7,0</td><td colspan="2">7,8</td><td>9,0</td><td colspan="2">10</td><td>12</td><td>14</td></tr>
<tr><td>38</td><td colspan="2"></td><td>100</td><td>7,0</td><td colspan="2">8,0</td><td>9,4</td><td colspan="2">11</td><td>13</td><td colspan="2">15</td><td>17</td><td>19</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td colspan="2">г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td></tr>
<tr><td colspan="15">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2">Твердости обрабатываемого материала</td><td colspan="4">Твердость сплава НВ, МПа Коэффициент К тв</td><td colspan="3">590...880 0,7</td><td colspan="3">980...1370 1,0</td><td colspan="3">1470...2450 1,20</td></tr>
</table>



###### <a id="p101006"></a>4.1.2. Горизонтально-вертикально- и шпоночно-фрезерные станки



<table>
<colgroup><col width="4%"><col width="9%"><col width="6%"><col width="3%"><col width="3%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="14">Неполное штучное время Фрезерование шпоночных пазов, Ra 2,5 11 квалитет</td><td colspan="9">Горизонтально-вертикально- и шпоночно-фрезерные станки</td></tr>
<tr><td colspan="14" rowspan="2">Сталь конструкционная, сигма = 590...740 МПа в</td><td colspan="9">Фрезы шпоночные из стали Р6М5</td></tr>
<tr><td colspan="9">Карта 30</td></tr>
<tr><td colspan="23">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Оборудование</td><td>Ширина</td><td colspan="2">Глубина</td><td rowspan="3">Число рабочих ходов, i</td><td colspan="17">Длина паза, l, мм, до</td></tr>
<tr><td>паза, В,</td><td colspan="2">паза, Н,</td><td>25</td><td>40</td><td>55</td><td>70</td><td>90</td><td>110</td><td>125</td><td>140</td><td>160</td><td>180</td><td>200</td><td>250</td><td colspan="2">300</td><td>350</td><td>400</td><td>500</td></tr>
<tr><td>мм, до</td><td colspan="2">мм, до</td><td colspan="17">Время на один паз, t , мин. нш</td></tr>
<tr><td>1</td><td>Гори-</td><td>6</td><td colspan="2">3,5</td><td>1</td><td>2,5</td><td>2,9</td><td>3,4</td><td>3,9</td><td>4,2</td><td>4,7</td><td>5,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>зонта-</td><td>8</td><td colspan="2">4,0</td><td></td><td>2,7</td><td>3,2</td><td>3,6</td><td>4,2</td><td>4,4</td><td>5,2</td><td>5,5</td><td>6,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>льно-</td><td>12</td><td colspan="2">4,5</td><td></td><td>2,9</td><td>3,4</td><td>4,0</td><td>4,5</td><td>5,2</td><td>5,9</td><td>6,5</td><td>7,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>верти-</td><td>16</td><td colspan="2">5,0</td><td></td><td>3,0</td><td>3,5</td><td>4,3</td><td>4,8</td><td>5,6</td><td>6,6</td><td>7,2</td><td>7,8</td><td>8,7</td><td>9,5</td><td>10</td><td>12</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>кально-</td><td>18</td><td colspan="2">5,5</td><td></td><td>-</td><td>3,6</td><td>4,5</td><td>5,1</td><td>6,0</td><td>7,0</td><td>7,8</td><td>8,4</td><td>9,5</td><td>10</td><td>11</td><td>13</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>фрезер-</td><td>20</td><td colspan="2">6,0</td><td></td><td>-</td><td>3,7</td><td>4,6</td><td>5,2</td><td>6,2</td><td>7,2</td><td>8,0</td><td>8,6</td><td>9,7</td><td>11</td><td>12</td><td>14</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>ный</td><td>24</td><td colspan="2">7,0</td><td></td><td>-</td><td>3,9</td><td>4,7</td><td>5,4</td><td>6,5</td><td>7,7</td><td>8,8</td><td>9,0</td><td>10</td><td>11</td><td>12</td><td>15</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>станок</td><td>28</td><td colspan="2">8,0</td><td></td><td>-</td><td>5,1</td><td>5,9</td><td>6,9</td><td>7,8</td><td>8,8</td><td>9,5</td><td>10</td><td>11</td><td>12</td><td>13</td><td>16</td><td colspan="2">19</td><td>22</td><td>25</td><td>30</td></tr>
<tr><td>9</td><td></td><td>32</td><td colspan="2">9,0</td><td></td><td>-</td><td>-</td><td>6,5</td><td>7,2</td><td>8,2</td><td>9,5</td><td>10</td><td>11</td><td>12</td><td>13</td><td>14</td><td>17</td><td colspan="2">20</td><td>23</td><td>26</td><td>31</td></tr>
<tr><td>10</td><td></td><td>36</td><td colspan="2">10</td><td></td><td>-</td><td>-</td><td>6,6</td><td>7,4</td><td>8,5</td><td>9,5</td><td>10</td><td>11</td><td>12</td><td>13</td><td>14</td><td>17</td><td colspan="2">20</td><td>23</td><td>26</td><td>31</td></tr>
<tr><td>11</td><td></td><td>40</td><td colspan="2">11</td><td></td><td>-</td><td>-</td><td>7,4</td><td>8,2</td><td>9,0</td><td>10</td><td>11</td><td>12</td><td>13</td><td>14</td><td>15</td><td>17</td><td colspan="2">21</td><td>24</td><td>27</td><td>32</td></tr>
<tr><td>12</td><td>Шпоноч-</td><td>6</td><td colspan="2">3,5</td><td>18</td><td>1,4</td><td>2,1</td><td>2,9</td><td>3,6</td><td>4,6</td><td>5,6</td><td>6,4</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>но-фре-</td><td>8</td><td colspan="2">4,0</td><td>20</td><td>1,5</td><td>2,4</td><td>3,4</td><td>4,4</td><td>5,4</td><td>6,7</td><td>7,7</td><td>8,6</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td>зерный</td><td>12</td><td colspan="2">4,5</td><td>23</td><td>1,6</td><td>2,7</td><td>3,9</td><td>5,0</td><td>6,5</td><td>8,0</td><td>9,0</td><td>10</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>станок</td><td>16</td><td colspan="2">5,0</td><td>25</td><td>1,6</td><td>2,7</td><td>4,0</td><td>5,3</td><td>7,1</td><td>8,8</td><td>10</td><td>12</td><td>14</td><td>15</td><td>16</td><td>20</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td></td><td>18</td><td colspan="2">5,5</td><td>28</td><td>-</td><td>2,7</td><td>4,4</td><td>5,8</td><td>7,8</td><td>8,9</td><td>11</td><td>13</td><td>15</td><td>17</td><td>19</td><td>23</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td></td><td>20</td><td colspan="2">6,0</td><td>30</td><td>-</td><td>2,7</td><td>4,6</td><td>6,2</td><td>8,4</td><td>11</td><td>12</td><td>14</td><td>16</td><td>19</td><td>21</td><td>25</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td></td><td>24</td><td colspan="2">7,0</td><td>35</td><td>-</td><td>2,8</td><td>5,2</td><td>7,2</td><td>10</td><td>13</td><td>15</td><td>17</td><td>20</td><td>23</td><td>26</td><td>32</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td></td><td>28</td><td colspan="2">8,0</td><td>40</td><td>-</td><td>2,8</td><td>5,6</td><td>8,2</td><td>12</td><td>15</td><td>18</td><td>21</td><td>24</td><td>27</td><td>30</td><td>38</td><td colspan="2">50</td><td>59</td><td>66</td><td>75</td></tr>
<tr><td>20</td><td></td><td>32</td><td colspan="2">9,0</td><td>45</td><td>-</td><td>-</td><td>5,8</td><td>8,4</td><td>13</td><td>16</td><td>20</td><td>23</td><td>27</td><td>31</td><td>35</td><td>50</td><td colspan="2">59</td><td>68</td><td>76</td><td>87</td></tr>
<tr><td>21</td><td></td><td>36</td><td colspan="2">10</td><td>50</td><td>-</td><td>-</td><td>5,9</td><td>8,9</td><td>14</td><td>18</td><td>22</td><td>26</td><td>30</td><td>35</td><td>40</td><td>48</td><td colspan="2">67</td><td>78</td><td>88</td><td>101</td></tr>
<tr><td>22</td><td></td><td>40</td><td colspan="2">11</td><td>55</td><td>-</td><td>-</td><td>6,4</td><td>10</td><td>14</td><td>19</td><td>24</td><td>28</td><td>33</td><td>38</td><td>44</td><td>54</td><td colspan="2">75</td><td>85</td><td>98</td><td>110</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td colspan="2">н</td><td>о</td><td>п</td><td>р</td></tr>
<tr><td colspan="23">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">1. Предела прочности обрабатываемого материала</td><td colspan="11">Предел прочности стали, сигма , МПа до 590 в Коэффициент К 0,9 пп</td><td colspan="4">590...740 1,0</td><td colspan="4">св. 740 1,2</td></tr>
<tr><td colspan="4">2. Шероховатости обрабатываемой поверхности</td><td colspan="13">Шероховатость поверхности Ra 2,5 Коэффициент К 1,0</td><td colspan="6">Ra 1,25 1,1</td></tr>
</table>



###### <a id="p101036"></a>4.1.3. Фрезерно-центровальные станки



<table>
<colgroup><col width="6%"><col width="17%"><col width="11%"><col width="12%"><col width="5%"><col width="3%"><col width="3%"><col width="11%"><col width="11%"><col width="6%"><col width="5%"><col width="11%"></colgroup>
<tr><td colspan="6" rowspan="3">Штучное время Фрезерование торцов и центрование отверстий Сталь конструкционная, сигма = 590...740 МПа в</td><td colspan="6">Фрезерно-центровальные станки</td></tr>
<tr><td colspan="6">Фрезы торцовые с пластинами Т15К6, сверла центровочные из стали Р6М5</td></tr>
<tr><td colspan="6">Карта 31</td></tr>
<tr><td colspan="12">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр заготовки,</td><td colspan="10">Длина заготовки, l, мм, до</td></tr>
<tr><td rowspan="2">D, мм, до</td><td>100</td><td>200</td><td colspan="3">400</td><td>600</td><td>800</td><td colspan="2">1000</td><td>1200</td></tr>
<tr><td colspan="10">Штучное время, t , мин. ш</td></tr>
<tr><td>1</td><td>30</td><td>1,3</td><td>1,4</td><td colspan="3">1,4</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td>2</td><td>50</td><td>1,7</td><td>1,8</td><td colspan="3">1,9</td><td>2,0</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td>3</td><td>75</td><td>2,4</td><td>2,5</td><td colspan="3">2,6</td><td>2,7</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td>4</td><td>100</td><td>3,8</td><td>4,0</td><td colspan="3">4,2</td><td>4,4</td><td>4,8</td><td colspan="2">5,4</td><td>-</td></tr>
<tr><td>5</td><td>125</td><td>4,7</td><td>4,8</td><td colspan="3">5,0</td><td>5,3</td><td>5,8</td><td colspan="2">6,2</td><td>6,3</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td colspan="3">в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td></tr>
<tr><td colspan="12">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2">Предела прочности обрабатываемого материала</td><td colspan="3">Прочность стали, сигма , МПа в Коэффициент К пп</td><td colspan="5">до 590 590...740 0,9 1,0</td><td colspan="2">св. 740 1,2</td></tr>
</table>



###### <a id="p101048"></a>4.1.4. Продольно-фрезерные станки



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="17">Неполное штучное время Продольно-фрезерные станки</td></tr>
<tr><td colspan="17">Чугун серый, НВ = 1760...2150 МПа Фрезы торцовые с пластинками ВК8, ВК6</td></tr>
<tr><td colspan="17">Карта 32</td></tr>
<tr><td colspan="17">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Характер</td><td rowspan="2">Ширина обрабатываемой</td><td rowspan="3">Число рабочих ходов, i</td><td colspan="13">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">обработки</td><td>100</td><td>200</td><td>300</td><td>400</td><td>500</td><td colspan="2">750</td><td>1000</td><td>1250</td><td>1500</td><td>1750</td><td>2000</td><td>2500</td></tr>
<tr><td>поверхности, В, мм</td><td colspan="13">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>50</td><td>1</td><td>2,6</td><td>2,7</td><td>2,9</td><td>3,1</td><td>3,3</td><td colspan="2">3,7</td><td>4,1</td><td>5,0</td><td>5,3</td><td>5,8</td><td>6,3</td><td>7,2</td></tr>
<tr><td>2</td><td>14...</td><td>60</td><td></td><td>2,6</td><td>2,8</td><td>3,1</td><td>3,2</td><td>3,4</td><td colspan="2">4,0</td><td>4,6</td><td>5,4</td><td>6,0</td><td>7,0</td><td>7,1</td><td>8,3</td></tr>
<tr><td>3</td><td>12</td><td>70</td><td></td><td>2,6</td><td>2,9</td><td>3,2</td><td>3,4</td><td>3,6</td><td colspan="2">4,4</td><td>5,1</td><td>6,0</td><td>6,7</td><td>7,4</td><td>8,2</td><td>9,0</td></tr>
<tr><td>4</td><td>квали-</td><td>110</td><td></td><td>2,8</td><td>3,3</td><td>3,6</td><td>4,1</td><td>4,6</td><td colspan="2">5,5</td><td>6,6</td><td>7,9</td><td>9,0</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>5</td><td>тет</td><td>150</td><td></td><td>2,9</td><td>3,5</td><td>4,0</td><td>4,6</td><td>5,2</td><td colspan="2">6,3</td><td>7,0</td><td>9,0</td><td>11</td><td>12</td><td>13</td><td>16</td></tr>
<tr><td>6</td><td></td><td>200</td><td></td><td>3,4</td><td>4,3</td><td>5,2</td><td>6,0</td><td>6,8</td><td colspan="2">8,5</td><td>10</td><td>13</td><td>15</td><td>18</td><td>20</td><td>25</td></tr>
<tr><td>7</td><td></td><td>250</td><td></td><td>3,8</td><td>4,9</td><td>6,0</td><td>7,1</td><td>8,2</td><td colspan="2">10</td><td>13</td><td>16</td><td>19</td><td>22</td><td>25</td><td>30</td></tr>
<tr><td>8</td><td>Rz 40</td><td>50</td><td>2</td><td>6,3</td><td>6,7</td><td>7,3</td><td>7,8</td><td>8,4</td><td colspan="2">9,5</td><td>11</td><td>12</td><td>14</td><td>15</td><td>16</td><td>19</td></tr>
<tr><td>9</td><td>...</td><td>60</td><td></td><td>6,4</td><td>7,0</td><td>7,5</td><td>8,0</td><td>8,6</td><td colspan="2">10</td><td>12</td><td>13</td><td>15</td><td>16</td><td>18</td><td>20</td></tr>
<tr><td>10</td><td>Rz 20;</td><td>75</td><td></td><td>6,5</td><td>7,2</td><td>7,8</td><td>8,4</td><td>9,0</td><td colspan="2">11</td><td>13</td><td>14</td><td>16</td><td>17</td><td>19</td><td>21</td></tr>
<tr><td>11</td><td>11</td><td>110</td><td></td><td>7,1</td><td>8,0</td><td>8,7</td><td>9,5</td><td>10</td><td colspan="2">12</td><td>14</td><td>17</td><td>19</td><td>21</td><td>23</td><td>28</td></tr>
<tr><td>12</td><td>квали-</td><td>150</td><td></td><td>7,7</td><td>8,9</td><td>10</td><td>11</td><td>12</td><td colspan="2">15</td><td>17</td><td>20</td><td>23</td><td>26</td><td>28</td><td>33</td></tr>
<tr><td>13</td><td>тет</td><td>200</td><td></td><td>9,0</td><td>10</td><td>12</td><td>14</td><td>16</td><td colspan="2">18</td><td>22</td><td>26</td><td>30</td><td>34</td><td>39</td><td>46</td></tr>
<tr><td>14</td><td></td><td>250</td><td></td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td colspan="2">23</td><td>28</td><td>33</td><td>38</td><td>43</td><td>48</td><td>57</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="10">Твердости Твердость чугуна, НВ, МПа обрабатываемого Коэффициент К материала тв</td><td colspan="4">до 2150 1,0</td><td colspan="3">св. 2150 1,2</td></tr>
</table>


<a id="p101070"></a>Примечание: При фрезеровании фрезами с пластинками ВК8 время по карте следует применять с коэффициентом К = 0,85.


<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="8">Неполное штучное время Фрезерование плоскостей</td><td colspan="12">Продольно-фрезерные станки</td></tr>
<tr><td colspan="8">Сталь конструкционная, сигма = 590...740 МПа</td><td colspan="12">Фрезы торцовые из стали Р6М5</td></tr>
<tr><td colspan="8">в</td><td colspan="12">Карта 33</td></tr>
<tr><td colspan="20">рисунок не приводится</td></tr>
<tr><td rowspan="4">N позиции</td><td>Характер</td><td rowspan="2">Длина обрабатываемой</td><td colspan="8">Заготовка из проката</td><td colspan="9">Поковка или отливка</td></tr>
<tr><td rowspan="3">обработки</td><td colspan="17">Ширина обрабатываемой поверхности, В, мм</td></tr>
<tr><td rowspan="2">поверхности, l, мм, до</td><td>50</td><td>65</td><td>75</td><td>110</td><td colspan="2">150</td><td>200</td><td>250</td><td>50</td><td colspan="2">60</td><td>75</td><td>110</td><td colspan="2">150</td><td>200</td><td>250</td></tr>
<tr><td colspan="17">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>100</td><td>3,2</td><td>3,3</td><td>3,4</td><td>3,5</td><td colspan="2">3,6</td><td>4,4</td><td>5,0</td><td>6,7</td><td colspan="2">7,0</td><td>7,2</td><td>7,4</td><td colspan="2">7,7</td><td>9,0</td><td>10</td></tr>
<tr><td>2</td><td>14...</td><td>200</td><td>4,3</td><td>4,6</td><td>4,7</td><td>4,8</td><td colspan="2">5,1</td><td>6,0</td><td>7,2</td><td>8,9</td><td colspan="2">9,5</td><td>10</td><td>11</td><td colspan="2">12</td><td>13</td><td>14</td></tr>
<tr><td>3</td><td>12</td><td>300</td><td>5,4</td><td>5,9</td><td>6,0</td><td>6,2</td><td colspan="2">6,4</td><td>7,6</td><td>9,0</td><td>11</td><td colspan="2">12</td><td>14</td><td>15</td><td colspan="2">16</td><td>17</td><td>18</td></tr>
<tr><td>4</td><td>квали-</td><td>400</td><td>6,4</td><td>7,4</td><td>7,5</td><td>7,6</td><td colspan="2">7,7</td><td>9,0</td><td>11</td><td>13</td><td colspan="2">14</td><td>15</td><td>16</td><td colspan="2">18</td><td>21</td><td>24</td></tr>
<tr><td>5</td><td>тет</td><td>500</td><td>7,5</td><td>8,6</td><td>8,9</td><td>9,0</td><td colspan="2">10</td><td>12</td><td>14</td><td>15</td><td colspan="2">17</td><td>18</td><td>19</td><td colspan="2">20</td><td>22</td><td>25</td></tr>
<tr><td>6</td><td></td><td>750</td><td>9,5</td><td>10</td><td>11</td><td>12</td><td colspan="2">14</td><td>16</td><td>18</td><td>20</td><td colspan="2">21</td><td>23</td><td>24</td><td colspan="2">25</td><td>31</td><td>37</td></tr>
<tr><td>7</td><td></td><td>1000</td><td>12</td><td>14</td><td>14</td><td>15</td><td colspan="2">17</td><td>20</td><td>23</td><td>26</td><td colspan="2">28</td><td>30</td><td>32</td><td colspan="2">35</td><td>41</td><td>48</td></tr>
<tr><td>8</td><td></td><td>1250</td><td>15</td><td>17</td><td>18</td><td>19</td><td colspan="2">22</td><td>25</td><td>28</td><td>32</td><td colspan="2">35</td><td>39</td><td>43</td><td colspan="2">48</td><td>54</td><td>59</td></tr>
<tr><td>9</td><td></td><td>1500</td><td>18</td><td>20</td><td>21</td><td>23</td><td colspan="2">27</td><td>31</td><td>35</td><td>37</td><td colspan="2">41</td><td>44</td><td>50</td><td colspan="2">58</td><td>64</td><td>72</td></tr>
<tr><td>10</td><td></td><td>1750</td><td>20</td><td>23</td><td>24</td><td>25</td><td colspan="2">27</td><td>34</td><td>39</td><td>44</td><td colspan="2">48</td><td>51</td><td>56</td><td colspan="2">63</td><td>73</td><td>83</td></tr>
<tr><td>11</td><td></td><td>2000</td><td>23</td><td>26</td><td>27</td><td>28</td><td colspan="2">33</td><td>38</td><td>44</td><td>50</td><td colspan="2">54</td><td>58</td><td>65</td><td colspan="2">73</td><td>84</td><td>95</td></tr>
<tr><td>12</td><td></td><td>2500</td><td>28</td><td>31</td><td>32</td><td>34</td><td colspan="2">40</td><td>46</td><td>53</td><td>59</td><td colspan="2">64</td><td>70</td><td>76</td><td colspan="2">84</td><td>98</td><td>113</td></tr>
<tr><td></td><td colspan="2">Число рабочих ходов</td><td colspan="8">1</td><td colspan="9">2</td></tr>
<tr><td>13</td><td>Rz 40</td><td>100</td><td>7,6</td><td>8,4</td><td>9,0</td><td>11</td><td colspan="2">13</td><td>16</td><td>20</td><td>11</td><td colspan="2">12</td><td>13</td><td>15</td><td colspan="2">17</td><td>21</td><td>26</td></tr>
<tr><td>14</td><td>...</td><td>200</td><td>9,5</td><td>11</td><td>12</td><td>14</td><td colspan="2">16</td><td>20</td><td>25</td><td>14</td><td colspan="2">16</td><td>17</td><td>19</td><td colspan="2">23</td><td>28</td><td>33</td></tr>
<tr><td>15</td><td>Rz 20;</td><td>300</td><td>11</td><td>13</td><td>15</td><td>17</td><td colspan="2">20</td><td>24</td><td>29</td><td>18</td><td colspan="2">20</td><td>21</td><td>24</td><td colspan="2">29</td><td>34</td><td>39</td></tr>
<tr><td>16</td><td>11</td><td>400</td><td>13</td><td>15</td><td>17</td><td>20</td><td colspan="2">24</td><td>29</td><td>35</td><td>21</td><td colspan="2">23</td><td>25</td><td>29</td><td colspan="2">35</td><td>41</td><td>47</td></tr>
<tr><td>17</td><td>квали-</td><td>500</td><td>15</td><td>18</td><td>20</td><td>24</td><td colspan="2">29</td><td>34</td><td>40</td><td>24</td><td colspan="2">26</td><td>30</td><td>36</td><td colspan="2">41</td><td>47</td><td>55</td></tr>
<tr><td>18</td><td>тет</td><td>750</td><td>19</td><td>23</td><td>27</td><td>32</td><td colspan="2">37</td><td>42</td><td>48</td><td>29</td><td colspan="2">31</td><td>36</td><td>42</td><td colspan="2">48</td><td>58</td><td>68</td></tr>
<tr><td>19</td><td></td><td>1000</td><td>23</td><td>28</td><td>32</td><td>38</td><td colspan="2">42</td><td>47</td><td>62</td><td>38</td><td colspan="2">41</td><td>48</td><td>55</td><td colspan="2">60</td><td>73</td><td>86</td></tr>
<tr><td>20</td><td></td><td>1250</td><td>29</td><td>35</td><td>40</td><td>45</td><td colspan="2">52</td><td>62</td><td>72</td><td>46</td><td colspan="2">54</td><td>60</td><td>66</td><td colspan="2">75</td><td>96</td><td>116</td></tr>
<tr><td>21</td><td></td><td>1500</td><td>35</td><td>42</td><td>46</td><td>53</td><td colspan="2">62</td><td>73</td><td>85</td><td>54</td><td colspan="2">63</td><td>70</td><td>78</td><td colspan="2">88</td><td>105</td><td>123</td></tr>
<tr><td>22</td><td></td><td>1750</td><td>40</td><td>45</td><td>51</td><td>60</td><td colspan="2">70</td><td>85</td><td>109</td><td>63</td><td colspan="2">74</td><td>83</td><td>90</td><td colspan="2">110</td><td>126</td><td>141</td></tr>
<tr><td>23</td><td></td><td>2000</td><td>44</td><td>50</td><td>59</td><td>67</td><td colspan="2">79</td><td>100</td><td>123</td><td>71</td><td colspan="2">83</td><td>95</td><td>111</td><td colspan="2">129</td><td>144</td><td>159</td></tr>
<tr><td>24</td><td></td><td>2500</td><td>52</td><td>64</td><td>68</td><td>82</td><td colspan="2">104</td><td>115</td><td>127</td><td>83</td><td colspan="2">98</td><td>114</td><td>130</td><td colspan="2">145</td><td>160</td><td>186</td></tr>
<tr><td></td><td colspan="2">Число рабочих ходов</td><td colspan="8">2</td><td colspan="9">3</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td colspan="2">м</td><td>н</td><td>о</td></tr>
<tr><td colspan="20">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="13">Предела прочности Предел прочности стали, до 590 обрабатываемого сигма , МПа материала в Коэффициент К 0,9 пп</td><td colspan="4">590...740 1,0</td><td colspan="3">св. 740 1,2</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="11%"><col width="11%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="15">Неполное штучное время Продольно-фрезерные станки</td></tr>
<tr><td colspan="15">Сталь конструкционная, Фрезы торцовые с пластинками Т5К10</td></tr>
<tr><td colspan="15">в Карта 34</td></tr>
<tr><td colspan="15">рисунок не приводится</td></tr>
<tr><td rowspan="4">N позиции</td><td>Характер</td><td rowspan="2">Длина обрабатываемой</td><td colspan="6">Заготовка из проката</td><td colspan="6">Поковка или отливка</td></tr>
<tr><td rowspan="3">обработки</td><td colspan="12">Ширина обрабатываемой поверхности, В, мм</td></tr>
<tr><td rowspan="2">поверхности, l, мм, до</td><td>60</td><td>75</td><td>110</td><td>150</td><td>200</td><td>250</td><td>60</td><td>75</td><td>110</td><td>150</td><td>200</td><td>250</td></tr>
<tr><td colspan="12">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>100</td><td>2,6</td><td>2,7</td><td>3,1</td><td>3,2</td><td>3,6</td><td>4,4</td><td>5,4</td><td>5,6</td><td>6,4</td><td>6,6</td><td>7,7</td><td>9,0</td></tr>
<tr><td>2</td><td>14...</td><td>200</td><td>3,1</td><td>3,2</td><td>4,0</td><td>4,2</td><td>4,7</td><td>6,3</td><td>6,4</td><td>6,6</td><td>8,4</td><td>8,6</td><td>9,5</td><td>13</td></tr>
<tr><td>3</td><td>12</td><td>300</td><td>3,4</td><td>3,5</td><td>4,7</td><td>5,0</td><td>5,8</td><td>8,0</td><td>7,2</td><td>7,6</td><td>10</td><td>11</td><td>13</td><td>16</td></tr>
<tr><td>4</td><td>квали-</td><td>400</td><td>3,7</td><td>4,0</td><td>5,4</td><td>5,8</td><td>7,0</td><td>9,5</td><td>8,0</td><td>8,4</td><td>11</td><td>12</td><td>16</td><td>20</td></tr>
<tr><td>5</td><td>тет</td><td>500</td><td>4,0</td><td>4,4</td><td>6,3</td><td>6,6</td><td>8,0</td><td>11</td><td>8,4</td><td>9,0</td><td>12</td><td>14</td><td>16</td><td>24</td></tr>
<tr><td>6</td><td></td><td>750</td><td>4,8</td><td>5,4</td><td>8,0</td><td>8,4</td><td>10</td><td>15</td><td>10</td><td>11</td><td>13</td><td>18</td><td>25</td><td>31</td></tr>
<tr><td>7</td><td></td><td>1000</td><td>5,6</td><td>6,4</td><td>10</td><td>11</td><td>14</td><td>18</td><td>12</td><td>14</td><td>21</td><td>28</td><td>34</td><td>40</td></tr>
<tr><td>8</td><td></td><td>1250</td><td>6,8</td><td>8,0</td><td>12</td><td>13</td><td>18</td><td>23</td><td>14</td><td>16</td><td>24</td><td>32</td><td>39</td><td>47</td></tr>
<tr><td>9</td><td></td><td>1500</td><td>7,8</td><td>9,0</td><td>14</td><td>15</td><td>19</td><td>25</td><td>16</td><td>18</td><td>29</td><td>36</td><td>42</td><td>52</td></tr>
<tr><td>10</td><td></td><td>1750</td><td>8,6</td><td>10</td><td>16</td><td>18</td><td>23</td><td>28</td><td>18</td><td>20</td><td>33</td><td>39</td><td>49</td><td>59</td></tr>
<tr><td>11</td><td></td><td>2000</td><td>9,0</td><td>11</td><td>17</td><td>19</td><td>25</td><td>31</td><td>20</td><td>22</td><td>36</td><td>42</td><td>54</td><td>65</td></tr>
<tr><td>12</td><td></td><td>2500</td><td>11</td><td>14</td><td>22</td><td>24</td><td>51</td><td>38</td><td>24</td><td>28</td><td>47</td><td>59</td><td>69</td><td>79</td></tr>
<tr><td></td><td colspan="2">Число рабочих ходов</td><td colspan="6">1</td><td colspan="6">2</td></tr>
<tr><td>13</td><td>Rz 40</td><td>100</td><td>6,3</td><td>6,6</td><td>7,5</td><td>8,5</td><td>10</td><td>13</td><td>9,0</td><td>9,5</td><td>11</td><td>12</td><td>15</td><td>18</td></tr>
<tr><td>14</td><td>...</td><td>200</td><td>7,1</td><td>7,6</td><td>9,0</td><td>10</td><td>13</td><td>16</td><td>10</td><td>11</td><td>13</td><td>15</td><td>19</td><td>23</td></tr>
<tr><td>15</td><td>Rz 20;</td><td>300</td><td>7,8</td><td>8,7</td><td>10</td><td>12</td><td>15</td><td>19</td><td>11</td><td>12</td><td>16</td><td>20</td><td>24</td><td>28</td></tr>
<tr><td>16</td><td>11</td><td>400</td><td>8,6</td><td>9,5</td><td>12</td><td>14</td><td>19</td><td>23</td><td>12</td><td>15</td><td>18</td><td>20</td><td>26</td><td>33</td></tr>
<tr><td>17</td><td>квали-</td><td>500</td><td>9,0</td><td>10</td><td>14</td><td>15</td><td>20</td><td>26</td><td>14</td><td>16</td><td>20</td><td>26</td><td>32</td><td>38</td></tr>
<tr><td>18</td><td>тет</td><td>750</td><td>11</td><td>12</td><td>16</td><td>19</td><td>25</td><td>31</td><td>16</td><td>18</td><td>26</td><td>32</td><td>40</td><td>47</td></tr>
<tr><td>19</td><td></td><td>1000</td><td>13</td><td>15</td><td>21</td><td>25</td><td>32</td><td>39</td><td>19</td><td>21</td><td>30</td><td>40</td><td>50</td><td>60</td></tr>
<tr><td>20</td><td></td><td>1250</td><td>15</td><td>18</td><td>25</td><td>30</td><td>38</td><td>46</td><td>23</td><td>27</td><td>37</td><td>47</td><td>59</td><td>71</td></tr>
<tr><td>21</td><td></td><td>1500</td><td>18</td><td>21</td><td>28</td><td>33</td><td>43</td><td>52</td><td>26</td><td>30</td><td>42</td><td>55</td><td>67</td><td>79</td></tr>
<tr><td>22</td><td></td><td>1750</td><td>19</td><td>22</td><td>32</td><td>36</td><td>46</td><td>59</td><td>28</td><td>34</td><td>50</td><td>63</td><td>76</td><td>89</td></tr>
<tr><td>23</td><td></td><td>2000</td><td>21</td><td>26</td><td>36</td><td>40</td><td>52</td><td>65</td><td>32</td><td>37</td><td>56</td><td>72</td><td>86</td><td>100</td></tr>
<tr><td>24</td><td></td><td>2500</td><td>26</td><td>31</td><td>44</td><td>50</td><td>64</td><td>79</td><td>37</td><td>46</td><td>68</td><td>85</td><td>102</td><td>118</td></tr>
<tr><td></td><td colspan="2">Число рабочих ходов</td><td colspan="6">2</td><td colspan="6">3</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
<tr><td colspan="15">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">Предела прочности обрабатываемого материала</td><td colspan="6">Предел прочности стали, сигма , МПа в Коэффициент К пп</td><td colspan="2">до 590 0,9</td><td colspan="2">590... 740 1,0</td><td colspan="2">св. 740 1,2</td></tr>
</table>



#### <a id="p101135"></a>4.2. Продольно- и поперечно-строгальные станки, долбежные станки



<table>
<colgroup><col width="4%"><col width="24%"><col width="13%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"></colgroup>
<tr><td colspan="8" rowspan="2">Вспомогательное время на установку и снятие детали при работе на столе или в приспособлении</td><td colspan="9">Продольно- и поперечно-строгальные, долбежные станки</td></tr>
<tr><td colspan="4">Карта 35</td><td colspan="5">лист 1</td></tr>
<tr><td rowspan="4">N позиции</td><td>Способ установки (рисунки не</td><td rowspan="4">Характер выверки</td><td colspan="7">Вручную</td><td colspan="7">Мостовым краном</td></tr>
<tr><td rowspan="3">приводятся)</td><td colspan="14">Масса детали, кг, до</td></tr>
<tr><td>1</td><td>3</td><td>5</td><td>10</td><td colspan="2">20</td><td>30</td><td>30</td><td>50</td><td>100</td><td>200</td><td>400</td><td>800</td><td>1500</td></tr>
<tr><td colspan="14">Время, t , мин. ву</td></tr>
<tr><td>1</td><td>В тисках</td><td>без выверки</td><td>0,65</td><td>0,8</td><td>0,9</td><td>1,0</td><td colspan="2">1,2</td><td>1,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td></td><td>с выверкой в одной плоскости</td><td>1,4</td><td>1,6</td><td>1,8</td><td>2,2</td><td colspan="2">2,5</td><td>3,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>В кулачках самоцентрирующего патрона</td><td>без выверки</td><td>0,5</td><td>0,8</td><td>0,9</td><td>1,2</td><td colspan="2">1,5</td><td>1,8</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td>8,5</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td></td><td>с выверкой</td><td>0,9</td><td>1,2</td><td>1,4</td><td>1,7</td><td colspan="2">2,1</td><td>2,6</td><td>8,0</td><td>8,3</td><td>9,0</td><td>9,8</td><td>10,9</td><td></td><td></td></tr>
<tr><td>5</td><td>На столе с креплением болтами и планками</td><td>без выверки</td><td>1,2</td><td>1,5</td><td>1,7</td><td>2,0</td><td colspan="2">2,5</td><td>3,5</td><td>6,5</td><td>7,4</td><td>8,5</td><td>9,8</td><td>11</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td></td><td>с выверкой в одной плоскости</td><td>2,0</td><td>3,0</td><td>3,2</td><td>3,8</td><td colspan="2">4,6</td><td>5,6</td><td>11</td><td>12</td><td>14</td><td>17</td><td>20</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td></td><td>с выверкой в двух плоскостях</td><td>3,0</td><td>4,0</td><td>5,0</td><td>5,7</td><td colspan="2">6,8</td><td>8,0</td><td>17</td><td>19</td><td>22</td><td>25</td><td>28</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>На столе с домкратами, подставками с креплением болтами и планками</td><td>без выверки</td><td>1,5</td><td>2,0</td><td>2,3</td><td>2,9</td><td colspan="2">3,5</td><td>4,2</td><td>7,5</td><td>8,5</td><td>10</td><td>12</td><td>14</td><td>17</td><td>20</td></tr>
<tr><td>9</td><td></td><td>с выверкой в одной плоскости</td><td>2,6</td><td>3,7</td><td>4,0</td><td>5,0</td><td colspan="2">6,3</td><td>7,2</td><td>13</td><td>15</td><td>18</td><td>21</td><td>25</td><td>31</td><td>35</td></tr>
<tr><td>10</td><td></td><td>с выверкой в двух плоскостях</td><td>3,2</td><td>4,5</td><td>5,4</td><td>6,5</td><td colspan="2">8,0</td><td>10</td><td>18</td><td>21</td><td>23</td><td>28</td><td>32</td><td>38</td><td>43</td></tr>
<tr><td>11</td><td></td><td>с выверкой в трех плоскостях</td><td>-</td><td>-</td><td>-</td><td>8,0</td><td colspan="2">10</td><td>12</td><td>22</td><td>26</td><td>29</td><td>35</td><td>40</td><td>48</td><td>54</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="24%"><col width="13%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"></colgroup>
<tr><td colspan="8" rowspan="2">Время на установку и снятие детали при работе на столе или в приспособлении</td><td colspan="9">Продольно- и поперечно-строгальные, долбежные станки</td></tr>
<tr><td colspan="4">Карта 35</td><td colspan="5">лист 2</td></tr>
<tr><td rowspan="4">N позиции</td><td rowspan="4">Способ установки</td><td rowspan="4">Характер выверки</td><td colspan="7">Вручную</td><td colspan="7">Мостовым краном</td></tr>
<tr><td colspan="14">Масса детали, кг, до</td></tr>
<tr><td>1,0</td><td>3,0</td><td>5,0</td><td>10</td><td colspan="2">20</td><td>30</td><td>30</td><td>50</td><td>100</td><td>200</td><td>400</td><td>800</td><td>1000</td></tr>
<tr><td colspan="14">Время, t , мин. ву</td></tr>
<tr><td>12</td><td>На столе с угольником (или сбоку стола) с креплением болтами и планками</td><td>без выверки</td><td>1,5</td><td>1,8</td><td>2,0</td><td>2,6</td><td colspan="2">3,0</td><td>3,5</td><td>7,5</td><td>8,3</td><td>10</td><td>12</td><td>13</td><td>15</td><td>17</td></tr>
<tr><td>13</td><td>рисунок не приводится</td><td>с выверкой в одной плоскости</td><td>2,3</td><td>3,2</td><td>4,0</td><td>4,5</td><td colspan="2">5,5</td><td>6,5</td><td>14</td><td>15</td><td>18</td><td>21</td><td>23</td><td>28</td><td>32</td></tr>
<tr><td>14</td><td></td><td>с выверкой в двух плоскостях</td><td>3,4</td><td>4,6</td><td>5,4</td><td>7,0</td><td colspan="2">8,0</td><td>9,0</td><td>19</td><td>21</td><td>25</td><td>29</td><td>32</td><td>38</td><td>44</td></tr>
<tr><td>15</td><td colspan="2">Время в карте предусматривает крепление детали болтами в количестве</td><td colspan="3">2</td><td colspan="11">4</td></tr>
<tr><td>16</td><td colspan="2">Добавлять (отнимать) на каждый болт сверх (менее) предусмотренных</td><td colspan="3">0,3</td><td colspan="5">0,4</td><td colspan="6">0,5</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>


<a id="p101162"></a>Примечания: 1. При установке деталей с необработанной поверхностью время по карте следует применять с коэффициентом К = 1,2.
2. <a id="p101163"></a>При переустановке деталей вручную время по карте следует принимать без изменения, при переустановке мостовым краном - с коэффициентом К = 0,8.
3. <a id="p101164"></a>При установке одновременно нескольких деталей время по карте для каждой последующей детали за первой следует применять с коэффициентом К = 0,8.


<table>
<colgroup><col width="5%"><col width="14%"><col width="9%"><col width="8%"><col width="5%"><col width="7%"><col width="4%"><col width="3%"><col width="5%"><col width="7%"><col width="7%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="7" rowspan="2">Вспомогательное время на приемку детали на станке</td><td colspan="8">Продольно-строгальные станки</td></tr>
<tr><td colspan="8">Карта 36</td></tr>
<tr><td rowspan="5">N позиции</td><td rowspan="5">Характер измерений</td><td>Квалитет</td><td rowspan="4">Число обмеров (количество контрольных</td><td colspan="11">Наибольшая измеряемая длина детали, L, мм, до</td></tr>
<tr><td rowspan="4">(класс точности размеров)</td><td colspan="4">3000</td><td colspan="4">6000</td><td colspan="3">8000</td></tr>
<tr><td colspan="11">Наибольшая измеряемая ширина, В, или высота, Н, мм</td></tr>
<tr><td>500</td><td>1000</td><td colspan="2">2000</td><td>500</td><td>1000</td><td>2000</td><td>500</td><td>1000</td><td>2000</td><td>2000</td></tr>
<tr><td>размеров)</td><td colspan="11">Время, t, мин.</td></tr>
<tr><td>1</td><td>Измерение</td><td>12...</td><td>4</td><td>1,6</td><td>1,9</td><td colspan="2">2,2</td><td>2,2</td><td>2,6</td><td>3,0</td><td>2,5</td><td>2,9</td><td>3,4</td><td>3,8</td></tr>
<tr><td>2</td><td>поверхно-</td><td>14</td><td>6</td><td>2,3</td><td>2,6</td><td colspan="2">3,0</td><td>3,1</td><td>3,6</td><td>4,1</td><td>3,5</td><td>4,1</td><td>4,6</td><td>5,3</td></tr>
<tr><td>3</td><td>стей де-</td><td></td><td>8</td><td>2,9</td><td>3,3</td><td colspan="2">3,8</td><td>3,9</td><td>4,5</td><td>5,1</td><td>4,4</td><td>5,1</td><td>5,8</td><td>6,7</td></tr>
<tr><td>4</td><td>тали уни-</td><td></td><td>10</td><td>3,5</td><td>4,0</td><td colspan="2">4,6</td><td>4,7</td><td>5,4</td><td>6,2</td><td>5,3</td><td>6,1</td><td>7,0</td><td>8,1</td></tr>
<tr><td>5</td><td>версаль-</td><td></td><td>15</td><td>4,8</td><td>5,5</td><td colspan="2">6,3</td><td>6,5</td><td>7,4</td><td>8,5</td><td>6,2</td><td>8,4</td><td>9,6</td><td>11</td></tr>
<tr><td>6</td><td>ными или</td><td></td><td>20</td><td>6,0</td><td>7,0</td><td colspan="2">8,0</td><td>8,1</td><td>9,5</td><td>11</td><td>9,2</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>7</td><td>простыми</td><td></td><td>25</td><td>7,2</td><td>8,4</td><td colspan="2">9,7</td><td>9,7</td><td>11</td><td>13</td><td>11</td><td>13</td><td>15</td><td>17</td></tr>
<tr><td>8</td><td>специаль-</td><td></td><td>35</td><td>9,4</td><td>11</td><td colspan="2">12</td><td>13</td><td>15</td><td>17</td><td>14</td><td>16</td><td>19</td><td>21</td></tr>
<tr><td>9</td><td>ными из-</td><td></td><td>45</td><td>11</td><td>13</td><td colspan="2">15</td><td>15</td><td>18</td><td>21</td><td>17</td><td>20</td><td>24</td><td>26</td></tr>
<tr><td>10</td><td>меритель-</td><td></td><td>55</td><td>13</td><td>16</td><td colspan="2">18</td><td>18</td><td>21</td><td>24</td><td>20</td><td>24</td><td>27</td><td>31</td></tr>
<tr><td>11</td><td rowspan="2">ными инструментами,</td><td></td><td>70</td><td>16</td><td>19</td><td colspan="2">22</td><td>22</td><td>26</td><td>30</td><td>25</td><td>29</td><td>34</td><td>37</td></tr>
<tr><td>12</td><td>9...11</td><td>2</td><td>1,3</td><td>1,8</td><td colspan="2">2,1</td><td>1,7</td><td>2,4</td><td>2,7</td><td>1,9</td><td>2,7</td><td>3,0</td><td>3,5</td></tr>
<tr><td>13</td><td>не требу-</td><td></td><td>4</td><td>2,4</td><td>3,3</td><td colspan="2">3,8</td><td>3,1</td><td>4,3</td><td>5,0</td><td>3,5</td><td>4,8</td><td>5,6</td><td>6,5</td></tr>
<tr><td>14</td><td>ющими их</td><td></td><td>6</td><td>3,4</td><td>4,6</td><td colspan="2">5,3</td><td>4,5</td><td>6,0</td><td>6,9</td><td>5,0</td><td>6,7</td><td>7,7</td><td>9,0</td></tr>
<tr><td>15</td><td>наладки и</td><td></td><td>8</td><td>4,3</td><td>5,9</td><td colspan="2">6,8</td><td>5,6</td><td>7,7</td><td>8,9</td><td>6,3</td><td>8,6</td><td>10</td><td>12</td></tr>
<tr><td>16</td><td>настройки</td><td></td><td>10</td><td>5,3</td><td>7,2</td><td colspan="2">8,3</td><td>7,0</td><td>9,4</td><td>11</td><td>7,8</td><td>11</td><td>12</td><td>14</td></tr>
<tr><td>17</td><td></td><td></td><td>12</td><td>6,2</td><td>8,5</td><td colspan="2">9,8</td><td>8,1</td><td>11</td><td>13</td><td>9,1</td><td>12</td><td>15</td><td>18</td></tr>
<tr><td>18</td><td></td><td></td><td>15</td><td>7,5</td><td>10</td><td colspan="2">12</td><td>9,8</td><td>13</td><td>16</td><td>11</td><td>15</td><td>18</td><td>21</td></tr>
<tr><td>19</td><td rowspan="2"></td><td></td><td>20</td><td>9,5</td><td>13</td><td colspan="2">15</td><td>12</td><td>17</td><td>20</td><td>14</td><td>19</td><td>22</td><td>26</td></tr>
<tr><td>20</td><td>7</td><td>2</td><td>1,6</td><td>2,2</td><td colspan="2">2,5</td><td>2,0</td><td>2,9</td><td>3,2</td><td>2,3</td><td>3,2</td><td>3,6</td><td>4,2</td></tr>
<tr><td>21</td><td></td><td></td><td>4</td><td>2,9</td><td>4,0</td><td colspan="2">4,6</td><td>3,8</td><td>5,2</td><td>6,1</td><td>4,3</td><td>5,8</td><td>6,8</td><td>7,9</td></tr>
<tr><td>22</td><td></td><td></td><td>6</td><td>4,1</td><td>5,5</td><td colspan="2">6,4</td><td>5,4</td><td>7,2</td><td>8,3</td><td>6,0</td><td>8,1</td><td>9,3</td><td>11</td></tr>
<tr><td>23</td><td></td><td></td><td>8</td><td>5,1</td><td>7,1</td><td colspan="2">8,2</td><td>6,7</td><td>9,3</td><td>11</td><td>7,5</td><td>10,5</td><td>12</td><td>14</td></tr>
<tr><td>24</td><td>Измерение инстру-</td><td>9-П 11</td><td>1</td><td>2,1</td><td>2,5</td><td colspan="2">2,9</td><td>2,7</td><td>3,2</td><td>3,7</td><td>3,0</td><td>3,5</td><td>4,1</td><td>4,8</td></tr>
<tr><td>25</td><td>ментами, требующи-</td><td></td><td>2</td><td>4,0</td><td>4,7</td><td colspan="2">5,5</td><td>5,1</td><td>6,0</td><td>7,1</td><td>5,6</td><td>6,6</td><td>7,8</td><td>9,1</td></tr>
<tr><td>26</td><td>ми сложных наст-</td><td></td><td>3</td><td>5,9</td><td>6,9</td><td colspan="2">8,0</td><td>7,6</td><td>8,9</td><td>10</td><td>8,4</td><td>9,8</td><td>11</td><td>13</td></tr>
<tr><td>27</td><td>роек. Определение</td><td></td><td>4</td><td>7,7</td><td>9,0</td><td colspan="2">11</td><td>9,9</td><td>11</td><td>14</td><td>11</td><td>12</td><td>15</td><td>18</td></tr>
<tr><td>28</td><td>размеров геометри-</td><td></td><td>5</td><td>9,5</td><td>11</td><td colspan="2">13</td><td>12</td><td>14</td><td>17</td><td>13</td><td>15</td><td>19</td><td>22</td></tr>
<tr><td>29</td><td>ческих</td><td></td><td>6</td><td>11</td><td>13</td><td colspan="2">16</td><td>14</td><td>17</td><td>21</td><td>15</td><td>19</td><td>23</td><td>27</td></tr>
<tr><td>30</td><td>форм и их взаимного</td><td></td><td>7</td><td>13</td><td>15</td><td colspan="2">18</td><td>17</td><td>19</td><td>23</td><td>19</td><td>21</td><td>25</td><td>29</td></tr>
<tr><td>31</td><td>располо-</td><td>7 (2)</td><td>1</td><td>2,5</td><td>3,0</td><td colspan="2">3,5</td><td>3,2</td><td>3,8</td><td>4,4</td><td>3,6</td><td>4,2</td><td>4,9</td><td>5,8</td></tr>
<tr><td>32</td><td>жения пу-</td><td></td><td>2</td><td>4,8</td><td>5,6</td><td colspan="2">6,6</td><td>6,1</td><td>7,2</td><td>8,5</td><td>6,7</td><td>7,9</td><td>9,3</td><td>11</td></tr>
<tr><td>33</td><td>тем слож-</td><td></td><td>3</td><td>6,9</td><td>7,1</td><td colspan="2">8,3</td><td>9,1</td><td>11</td><td>12</td><td>10</td><td>12</td><td>13</td><td>16</td></tr>
<tr><td>34</td><td>ных вы-</td><td></td><td>4</td><td>9,3</td><td>11</td><td colspan="2">13</td><td>12</td><td>13</td><td>17</td><td>13</td><td>14</td><td>18</td><td>22</td></tr>
<tr><td>35</td><td>числений</td><td></td><td>5</td><td>11</td><td>13</td><td colspan="2">16</td><td>14</td><td>17</td><td>20</td><td>16</td><td>18</td><td>23</td><td>26</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>


<a id="p101203"></a>Примечание: Время на приемку деталей на станке контролером включается в норму станочника в тех случаях, когда она не перекрывается другими работами и присутствие станочника при приемке предусмотрено технологическим процессом.


##### <a id="p101204"></a>Неполное штучное время



<table>
<colgroup><col width="6%"><col width="22%"><col width="17%"><col width="6%"><col width="12%"><col width="18%"><col width="18%"></colgroup>
<tr><td colspan="4" rowspan="3">Неполное штучное время Строгание фасок, Rz 40 Сталь конструкционная. Чугун</td><td colspan="3">Продольно-поперечно-строгальные станки</td></tr>
<tr><td colspan="3">Резцы с пластинками твердого сплава Т15К6, ВК8</td></tr>
<tr><td colspan="3">Карта 37</td></tr>
<tr><td colspan="7">рисунок не приводится</td></tr>
<tr><td rowspan="5">N позиции</td><td rowspan="5">Наименование станка</td><td rowspan="5">Длина строгания, l, мм, до:</td><td colspan="4">Размер фаски d x альфа°</td></tr>
<tr><td colspan="2">5 x 45</td><td>10 x 45</td><td>15 x 45</td></tr>
<tr><td colspan="4">Глубина резания, t, мм</td></tr>
<tr><td colspan="2">3,5</td><td>7,0</td><td>11</td></tr>
<tr><td colspan="4">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Продольно-</td><td>500</td><td colspan="2">1,7</td><td>2,6</td><td>4,3</td></tr>
<tr><td>2</td><td>строгальный</td><td>1000</td><td colspan="2">1,8</td><td>2,8</td><td>4,7</td></tr>
<tr><td>3</td><td></td><td>1500</td><td colspan="2">1,9</td><td>3,0</td><td>5,0</td></tr>
<tr><td>4</td><td></td><td>2000</td><td colspan="2">2,0</td><td>3,2</td><td>5,5</td></tr>
<tr><td>5</td><td></td><td>2500</td><td colspan="2">2,2</td><td>3,5</td><td>6,0</td></tr>
<tr><td>6</td><td></td><td>3000</td><td colspan="2">2,4</td><td>3,7</td><td>6,6</td></tr>
<tr><td>7</td><td></td><td>4000</td><td colspan="2">2,6</td><td>4,3</td><td>7,5</td></tr>
<tr><td>8</td><td></td><td>5000</td><td colspan="2">2,8</td><td>4,6</td><td>7,8</td></tr>
<tr><td>9</td><td></td><td>6000</td><td colspan="2">3,0</td><td>5,0</td><td>8,5</td></tr>
<tr><td>10</td><td>Поперечно-</td><td>500</td><td colspan="2">1,4</td><td>1,8</td><td>-</td></tr>
<tr><td>11</td><td>строгальный</td><td>600</td><td colspan="2">2,0</td><td>2,5</td><td>-</td></tr>
<tr><td>12</td><td></td><td>800</td><td colspan="2">2,9</td><td>3,7</td><td>-</td></tr>
<tr><td colspan="3">Индекс</td><td colspan="2">а</td><td>б</td><td>в</td></tr>
</table>



###### <a id="p101224"></a>4.2.1. Продольно-строгальные станки



<table>
<colgroup><col width="5%"><col width="8%"><col width="8%"><col width="4%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"><col width="6%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="9">Неполное штучное время Строгание плоскостей</td><td colspan="11">Продольно-строгальные станки</td></tr>
<tr><td colspan="9" rowspan="2">Чугун серый, НВ = 1760...2150 МПа</td><td colspan="11">Резцы проходные с пластинками ВК8</td></tr>
<tr><td colspan="11">Карта 38</td></tr>
<tr><td colspan="20">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Характер</td><td rowspan="2">Длина обрабатываемой</td><td colspan="2" rowspan="2">Число проходов,</td><td colspan="15">Ширина обрабатываемой поверхности, В, мм, до</td></tr>
<tr><td rowspan="2">обработки</td><td>50</td><td>75</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td colspan="2">500</td><td>600</td><td>700</td><td>800</td><td>1000</td></tr>
<tr><td>поверхности, l, мм</td><td colspan="2">i</td><td colspan="15">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>200</td><td colspan="2">1</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,8</td><td>7,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>14...</td><td>500</td><td colspan="2"></td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td>12</td><td>14</td><td>15</td><td>17</td><td>19</td><td colspan="2">22</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>12</td><td>1000</td><td colspan="2"></td><td>8,3</td><td>9,0</td><td>11</td><td>14</td><td>17</td><td>21</td><td>24</td><td>27</td><td>31</td><td colspan="2">35</td><td>43</td><td>52</td><td>56</td><td>60</td></tr>
<tr><td>4</td><td>квали-</td><td>1500</td><td colspan="2"></td><td>10</td><td>11</td><td>14</td><td>17</td><td>22</td><td>27</td><td>31</td><td>42</td><td>47</td><td colspan="2">50</td><td>58</td><td>67</td><td>77</td><td>85</td></tr>
<tr><td>5</td><td>тет</td><td>2000</td><td colspan="2"></td><td>12</td><td>14</td><td>17</td><td>21</td><td>27</td><td>33</td><td>41</td><td>45</td><td>52</td><td colspan="2">60</td><td>73</td><td>86</td><td>95</td><td>104</td></tr>
<tr><td>6</td><td></td><td>2500</td><td colspan="2"></td><td>14</td><td>16</td><td>20</td><td>25</td><td>32</td><td>41</td><td>49</td><td>58</td><td>65</td><td colspan="2">77</td><td>95</td><td>110</td><td>125</td><td>138</td></tr>
<tr><td>7</td><td></td><td>3000</td><td colspan="2"></td><td>16</td><td>20</td><td>23</td><td>29</td><td>39</td><td>48</td><td>56</td><td>67</td><td>76</td><td colspan="2">91</td><td>107</td><td>127</td><td>146</td><td>162</td></tr>
<tr><td>8</td><td></td><td>4000</td><td colspan="2"></td><td>20</td><td>23</td><td>28</td><td>36</td><td>48</td><td>60</td><td>71</td><td>83</td><td>95</td><td colspan="2">111</td><td>135</td><td>158</td><td>179</td><td>182</td></tr>
<tr><td>9</td><td></td><td>5000</td><td colspan="2"></td><td>24</td><td>27</td><td>35</td><td>46</td><td>60</td><td>75</td><td>86</td><td>105</td><td>120</td><td colspan="2">149</td><td>171</td><td>204</td><td>228</td><td>282</td></tr>
<tr><td>10</td><td></td><td>6000</td><td colspan="2"></td><td>27</td><td>32</td><td>41</td><td>54</td><td>72</td><td>90</td><td>107</td><td>125</td><td>142</td><td colspan="2">176</td><td>205</td><td>243</td><td>273</td><td>362</td></tr>
<tr><td>11</td><td>Rz 40,</td><td>200</td><td colspan="2">2</td><td>9,5</td><td>11</td><td>11,5</td><td>13</td><td>14,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>Rz 20;</td><td>500</td><td colspan="2"></td><td>11,5</td><td>13,5</td><td>14,5</td><td>18</td><td>21</td><td>23</td><td>26</td><td>28</td><td>31</td><td colspan="2">36</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>11</td><td>1000</td><td colspan="2"></td><td>14,5</td><td>16</td><td>19</td><td>23</td><td>27</td><td>31</td><td>35</td><td>40</td><td>45</td><td colspan="2">52</td><td>62</td><td>73</td><td>80</td><td>87</td></tr>
<tr><td>14</td><td>квали-</td><td>1500</td><td colspan="2"></td><td>17</td><td>18</td><td>23</td><td>27</td><td>35</td><td>40</td><td>45</td><td>56</td><td>65</td><td colspan="2">71</td><td>82</td><td>94</td><td>107</td><td>118</td></tr>
<tr><td>15</td><td>тет</td><td>2000</td><td colspan="2"></td><td>19</td><td>21</td><td>26</td><td>33</td><td>40</td><td>50</td><td>59</td><td>66</td><td>74</td><td colspan="2">85</td><td>103</td><td>121</td><td>135</td><td>150</td></tr>
<tr><td>16</td><td></td><td>2500</td><td colspan="2"></td><td>22</td><td>26</td><td>31</td><td>39</td><td>47</td><td>59</td><td>71</td><td>82</td><td>91</td><td colspan="2">107</td><td>130</td><td>151</td><td>171</td><td>189</td></tr>
<tr><td>17</td><td></td><td>3000</td><td colspan="2"></td><td>24</td><td>30</td><td>35</td><td>45</td><td>56</td><td>69</td><td>81</td><td>94</td><td>106</td><td colspan="2">126</td><td>149</td><td>176</td><td>200</td><td>223</td></tr>
<tr><td>18</td><td></td><td>4000</td><td colspan="2"></td><td>29</td><td>34</td><td>43</td><td>55</td><td>70</td><td>85</td><td>100</td><td>116</td><td>132</td><td colspan="2">156</td><td>186</td><td>218</td><td>245</td><td>268</td></tr>
<tr><td>19</td><td></td><td>5000</td><td colspan="2"></td><td>31</td><td>37</td><td>49</td><td>62</td><td>79</td><td>98</td><td>113</td><td>135</td><td>153</td><td colspan="2">190</td><td>200</td><td>269</td><td>302</td><td>373</td></tr>
<tr><td>20</td><td></td><td>6000</td><td colspan="2"></td><td>36</td><td>43</td><td>54</td><td>72</td><td>94</td><td>116</td><td>137</td><td>160</td><td>181</td><td colspan="2">223</td><td>262</td><td>308</td><td>346</td><td>453</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
<tr><td colspan="20">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td>1.</td><td colspan="3">Обрабатываемого материала</td><td colspan="11">Чугун, твердость, НВ, МПа Коэффициент К тв</td><td colspan="3">до 2150 1,0</td><td colspan="2">св. 2150 1,2</td></tr>
<tr><td>2.</td><td colspan="3">Угла в плане резца</td><td colspan="11">фи, град. Коэффициент К фи</td><td colspan="3">45°...60° 1,0</td><td colspan="2">90° 1,3</td></tr>
<tr><td rowspan="2">3.</td><td colspan="3">Числа одновременно работающих</td><td colspan="11">Число одновременно работающих суппортов</td><td colspan="3">1</td><td colspan="2">2</td></tr>
<tr><td colspan="3">суппортов</td><td colspan="11">Коэффициент при одной поверхности обработке К нескольких поверхностей рс</td><td colspan="3">1,0 1,0</td><td colspan="2">0,6 1,2</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="8%"><col width="8%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="17">Неполное штучное время Продольно-строгальные станки Строгание прямоугольных пазов, Rz 80; 14...12 квалитет Резцы с пластинками ВК8 Чугун серый, НВ = 1760...2150 МПа</td></tr>
<tr><td colspan="17">Карта 39</td></tr>
<tr><td colspan="17">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина</td><td>Глубина</td><td>Число</td><td colspan="13">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>паза, В,</td><td>паза, Н,</td><td rowspan="2">проходов, i</td><td>200</td><td>500</td><td>750</td><td colspan="2">1000</td><td>1500</td><td>2000</td><td>2500</td><td colspan="2">3000</td><td>4000</td><td>5000</td><td>6000</td></tr>
<tr><td>мм, до</td><td>мм, до</td><td colspan="13">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>10</td><td>5</td><td>1</td><td>4,5</td><td>5,0</td><td>5,5</td><td colspan="2">6,0</td><td>6,4</td><td>7,5</td><td>8,0</td><td colspan="2">11</td><td>12</td><td>14</td><td>15</td></tr>
<tr><td>2</td><td></td><td>12</td><td></td><td>5,5</td><td>6,5</td><td>7,0</td><td colspan="2">8,0</td><td>9,0</td><td>11,0</td><td>13</td><td colspan="2">17</td><td>18</td><td>21</td><td>24</td></tr>
<tr><td>3</td><td></td><td>20</td><td></td><td>6,0</td><td>7,0</td><td>7,5</td><td colspan="2">8,0</td><td>10</td><td>12,0</td><td>14</td><td colspan="2">18</td><td>21</td><td>28</td><td>32</td></tr>
<tr><td>4</td><td>15</td><td>10</td><td>1</td><td>5,0</td><td>5,5</td><td>6,0</td><td colspan="2">6,5</td><td>7,0</td><td>8,6</td><td>11</td><td colspan="2">13</td><td>14</td><td>17</td><td>19</td></tr>
<tr><td>5</td><td></td><td>20</td><td></td><td>6,0</td><td>7,5</td><td>8,0</td><td colspan="2">8,5</td><td>11</td><td>13</td><td>16</td><td colspan="2">19</td><td>22</td><td>27</td><td>31</td></tr>
<tr><td>6</td><td></td><td>30</td><td></td><td>6,5</td><td>8,0</td><td>8,5</td><td colspan="2">10</td><td>13</td><td>15</td><td>18</td><td colspan="2">23</td><td>27</td><td>36</td><td>42</td></tr>
<tr><td>7</td><td>20</td><td>30</td><td>1</td><td>6,5</td><td>8,5</td><td>9,0</td><td colspan="2">11</td><td>13</td><td>16</td><td>20</td><td colspan="2">24</td><td>28</td><td>37</td><td>45</td></tr>
<tr><td>8</td><td></td><td>40</td><td></td><td>7,5</td><td>9,5</td><td>11</td><td colspan="2">13</td><td>16</td><td>20</td><td>26</td><td colspan="2">31</td><td>36</td><td>44</td><td>57</td></tr>
<tr><td>9</td><td>25</td><td>30</td><td>2</td><td>10</td><td>12</td><td>13</td><td colspan="2">15</td><td>19</td><td>24</td><td>31</td><td colspan="2">38</td><td>45</td><td>55</td><td>72</td></tr>
<tr><td>10</td><td></td><td>40</td><td></td><td>12</td><td>14</td><td>15</td><td colspan="2">18</td><td>24</td><td>31</td><td>40</td><td colspan="2">48</td><td>56</td><td>72</td><td>93</td></tr>
<tr><td>11</td><td>30</td><td>40</td><td>2</td><td>12</td><td>14</td><td>16</td><td colspan="2">18</td><td>24</td><td>31</td><td>40</td><td colspan="2">48</td><td>56</td><td>72</td><td>93</td></tr>
<tr><td>12</td><td></td><td>50</td><td></td><td>13</td><td>15</td><td>18</td><td colspan="2">22</td><td>28</td><td>36</td><td>47</td><td colspan="2">59</td><td>70</td><td>86</td><td>113</td></tr>
<tr><td>13</td><td>50</td><td>50</td><td>3</td><td>15</td><td>20</td><td>22</td><td colspan="2">27</td><td>36</td><td>47</td><td>64</td><td colspan="2">76</td><td>91</td><td>129</td><td>135</td></tr>
<tr><td>14</td><td></td><td>70</td><td></td><td>18</td><td>24</td><td>26</td><td colspan="2">33</td><td>43</td><td>56</td><td>77</td><td colspan="2">91</td><td>109</td><td>155</td><td>162</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td>1.</td><td colspan="12">Обрабатываемого Чугун, твердость, НВ, МПа материала Коэффициент К тв</td><td colspan="4">до 2150 св. 2150 1,0 1,2</td></tr>
<tr><td rowspan="2">2.</td><td colspan="12">Числа одновре- Число одновременно работающих менно работаю- суппортов</td><td colspan="4">1 2</td></tr>
<tr><td colspan="7">Коэффициент К рс</td><td colspan="5">одной поверхности нескольких поверхностей</td><td colspan="4">1,0 0,6 1,0 1,2</td></tr>
<tr><td>3.</td><td colspan="12">Отношения ско- Отношение скорости рабочего хода к рости рабочего холостому, до хода к холос- Коэффициент К тому m</td><td colspan="3">0,2 0,5 0,83 1,0</td><td>0,7 1,1</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="8%"><col width="8%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="17">Неполное штучное время Продольно-строгальные станки Строгание прямоугольных пазов, Rz 80; 14...12 квалитет Резцы из стали Р6М5 Чугун серый, НВ = 1760...2150 МПа</td></tr>
<tr><td colspan="17">Карта 40</td></tr>
<tr><td colspan="17">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина</td><td>Глубина</td><td>Число</td><td colspan="13">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>паза, В,</td><td>паза, Н,</td><td rowspan="2">проходов, i</td><td>200</td><td>500</td><td>750</td><td colspan="2">1000</td><td>1500</td><td>2000</td><td>2500</td><td colspan="2">3000</td><td>4000</td><td>5000</td><td>6000</td></tr>
<tr><td>мм, до</td><td>мм, до</td><td colspan="13">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>10</td><td>5</td><td>1</td><td>5,0</td><td>6,0</td><td>6,5</td><td colspan="2">7,0</td><td>8,0</td><td>9,0</td><td>11</td><td colspan="2">14</td><td>15</td><td>18</td><td>21</td></tr>
<tr><td>2</td><td></td><td>12</td><td></td><td>6,5</td><td>8,0</td><td>9,0</td><td colspan="2">10</td><td>12</td><td>14</td><td>17</td><td colspan="2">22</td><td>26</td><td>31</td><td>35</td></tr>
<tr><td>3</td><td></td><td>20</td><td></td><td>7,0</td><td>9,0</td><td>10</td><td colspan="2">11,0</td><td>13</td><td>16</td><td>21</td><td colspan="2">26</td><td>31</td><td>45</td><td>53</td></tr>
<tr><td>4</td><td>15</td><td>10</td><td>1</td><td>5,5</td><td>6,5</td><td>7,5</td><td colspan="2">8,0</td><td>9,5</td><td>12</td><td>14</td><td colspan="2">17</td><td>20</td><td>24</td><td>27</td></tr>
<tr><td>5</td><td></td><td>20</td><td></td><td>7,0</td><td>9,0</td><td>10</td><td colspan="2">12</td><td>14</td><td>17</td><td>22</td><td colspan="2">27</td><td>32</td><td>39</td><td>45</td></tr>
<tr><td>6</td><td></td><td>30</td><td></td><td>7,5</td><td>10</td><td>11</td><td colspan="2">13</td><td>16</td><td>20</td><td>28</td><td colspan="2">35</td><td>42</td><td>54</td><td>64</td></tr>
<tr><td>7</td><td>20</td><td>30</td><td>1</td><td>8,0</td><td>11</td><td>12</td><td colspan="2">14</td><td>17</td><td>21</td><td>30</td><td colspan="2">36</td><td>43</td><td>53</td><td>63</td></tr>
<tr><td>8</td><td></td><td>40</td><td></td><td>10</td><td>13</td><td>14</td><td colspan="2">16</td><td>21</td><td>30</td><td>38</td><td colspan="2">46</td><td>55</td><td>68</td><td>78</td></tr>
<tr><td>9</td><td>25</td><td>30</td><td>2</td><td>13</td><td>15</td><td>16</td><td colspan="2">20</td><td>25</td><td>32</td><td>46</td><td colspan="2">56</td><td>67</td><td>83</td><td>100</td></tr>
<tr><td>10</td><td></td><td>40</td><td></td><td>15</td><td>18</td><td>20</td><td colspan="2">25</td><td>32</td><td>41</td><td>58</td><td colspan="2">73</td><td>86</td><td>108</td><td>134</td></tr>
<tr><td>11</td><td>30</td><td>40</td><td>2</td><td>15</td><td>18</td><td>20</td><td colspan="2">25</td><td>32</td><td>41</td><td>58</td><td colspan="2">73</td><td>86</td><td>108</td><td>134</td></tr>
<tr><td>12</td><td></td><td>50</td><td></td><td>16</td><td>20</td><td>23</td><td colspan="2">30</td><td>39</td><td>51</td><td>71</td><td colspan="2">90</td><td>106</td><td>132</td><td>159</td></tr>
<tr><td>13</td><td>50</td><td>50</td><td>2</td><td>20</td><td>28</td><td>32</td><td colspan="2">41</td><td>54</td><td>71</td><td>94</td><td colspan="2">117</td><td>140</td><td>174</td><td>196</td></tr>
<tr><td>14</td><td></td><td>70</td><td></td><td>25</td><td>34</td><td>39</td><td colspan="2">50</td><td>65</td><td>86</td><td>113</td><td colspan="2">141</td><td>168</td><td>209</td><td>236</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td>1.</td><td colspan="12">Обрабатываемого Чугун, твердость НВ, МПа материала Коэффициент К тв</td><td colspan="4">до 2150 св. 2150 1,0 1,2</td></tr>
<tr><td rowspan="2">2.</td><td colspan="12">Числа одновре- Число одновременно работающих менно работаю- суппортов</td><td colspan="4">1 2</td></tr>
<tr><td colspan="7">Коэффициент К рс</td><td colspan="5">одной поверхности нескольких поверхностей</td><td colspan="4">1,0 0,6 1,0 1,2</td></tr>
<tr><td>3.</td><td colspan="12">Отношения ско- Отношение скорости рабочего хода к рости рабочего холостому, до хода к холос- Коэффициент К тому m</td><td colspan="3">0,2 0,5 0,83 1,0</td><td>0,7 1,1</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="3%"><col width="6%"><col width="4%"><col width="3%"><col width="2%"><col width="4%"><col width="5%"></colgroup>
<tr><td colspan="13">Неполное штучное время Строгание Т-образных пазов, Rz 80; 14...12 квалитет</td><td colspan="12">Продольно-строгальные станки</td></tr>
<tr><td colspan="13" rowspan="2">Чугун серый, НВ = 1760...2150 МПа</td><td colspan="12">Резцы с пластинками ВК8</td></tr>
<tr><td colspan="12">Карта 41</td></tr>
<tr><td colspan="25">рисунок не приводится</td></tr>
<tr><td rowspan="7">N позиции</td><td rowspan="2">Длина Т-образного паза, l,</td><td colspan="23">Ширина Т-образного паза, В, мм</td></tr>
<tr><td colspan="2">16</td><td colspan="2">19</td><td colspan="3">23</td><td colspan="2">30</td><td colspan="3">37</td><td colspan="2">46</td><td colspan="2">56</td><td colspan="2">68</td><td colspan="3">80</td><td colspan="2">96</td></tr>
<tr><td rowspan="5">мм, до</td><td colspan="23">Ширина прямоугольного паза, В , мм 1</td></tr>
<tr><td colspan="2">10</td><td colspan="2">12</td><td colspan="3">14</td><td colspan="2">18</td><td colspan="3">22</td><td colspan="2">28</td><td colspan="2">36</td><td colspan="2">42</td><td colspan="3">48</td><td colspan="2">54</td></tr>
<tr><td colspan="23">Глубина прямоугольного паза, h, мм</td></tr>
<tr><td colspan="2">13 21</td><td colspan="2">16 25</td><td colspan="3">19 28</td><td colspan="2">24 36</td><td colspan="3">31 45</td><td colspan="2">38 56</td><td colspan="2">48 71</td><td colspan="2">58 85</td><td colspan="3">65 95</td><td colspan="2">75 106</td></tr>
<tr><td colspan="23">Время на один паз, t , мин. нш</td></tr>
<tr><td>1</td><td>250</td><td colspan="2">25 27</td><td colspan="2">26 33</td><td colspan="3">27 34</td><td colspan="2">39 43</td><td colspan="3">41 45</td><td colspan="2">46 51</td><td colspan="2">56 60</td><td colspan="2">63 64</td><td colspan="3">65 72</td><td colspan="2">74 79</td></tr>
<tr><td>2</td><td>500</td><td colspan="2">27 30</td><td colspan="2">29 36</td><td colspan="3">30 37</td><td colspan="2">46 50</td><td colspan="3">48 53</td><td colspan="2">54 59</td><td colspan="2">68 74</td><td colspan="2">76 83</td><td colspan="3">85 104</td><td colspan="2">102 109</td></tr>
<tr><td>3</td><td>750</td><td colspan="2">29 31</td><td colspan="2">30 42</td><td colspan="3">31 41</td><td colspan="2">52 57</td><td colspan="3">56 63</td><td colspan="2">64 70</td><td colspan="2">80 88</td><td colspan="2">90 101</td><td colspan="3">102 113</td><td colspan="2">110 124</td></tr>
<tr><td>4</td><td>1000</td><td colspan="2">31 35</td><td colspan="2">33 45</td><td colspan="3">35 48</td><td colspan="2">57 65</td><td colspan="3">63 71</td><td colspan="2">74 80</td><td colspan="2">95 104</td><td colspan="2">108 121</td><td colspan="3">124 136</td><td colspan="2">133 147</td></tr>
<tr><td>5</td><td>1500</td><td colspan="2">36 39</td><td colspan="2">38 54</td><td colspan="3">41 57</td><td colspan="2">74 82</td><td colspan="3">79 90</td><td colspan="2">93 102</td><td colspan="2">121 136</td><td colspan="2">140 158</td><td colspan="3">162 181</td><td colspan="2">177 198</td></tr>
<tr><td>6</td><td>2000</td><td colspan="2">41 44</td><td colspan="2">44 63</td><td colspan="3">45 68</td><td colspan="2">85 96</td><td colspan="3">94 113</td><td colspan="2">116 127</td><td colspan="2">147 166</td><td colspan="2">170 195</td><td colspan="3">198 223</td><td colspan="2">221 243</td></tr>
<tr><td>7</td><td>2500</td><td colspan="2">45 48</td><td colspan="2">49 66</td><td colspan="3">53 80</td><td colspan="2">103 116</td><td colspan="3">113 130</td><td colspan="2">132 155</td><td colspan="2">181 203</td><td colspan="2">212 242</td><td colspan="3">243 274</td><td colspan="2">271 305</td></tr>
<tr><td>8</td><td>3000</td><td colspan="2">49 53</td><td colspan="2">52 85</td><td colspan="3">59 90</td><td colspan="2">116 130</td><td colspan="3">127 147</td><td colspan="2">153 176</td><td colspan="2">201 237</td><td colspan="2">249 283</td><td colspan="3">286 321</td><td colspan="2">316 356</td></tr>
<tr><td>9</td><td>3500</td><td colspan="2">56 57</td><td colspan="2">56 95</td><td colspan="3">65 103</td><td colspan="2">131 149</td><td colspan="3">146 167</td><td colspan="2">174 203</td><td colspan="2">237 269</td><td colspan="2">282 319</td><td colspan="3">321 369</td><td colspan="2">364 407</td></tr>
<tr><td>10</td><td>4000</td><td colspan="2">57 62</td><td colspan="2">63 102</td><td colspan="3">71 110</td><td colspan="2">142 164</td><td colspan="3">161 182</td><td colspan="2">189 221</td><td colspan="2">261 294</td><td colspan="2">304 356</td><td colspan="3">361 404</td><td colspan="2">400 448</td></tr>
<tr><td>11</td><td>5000</td><td colspan="2">- -</td><td colspan="2">73 122</td><td colspan="3">87 130</td><td colspan="2">170 203</td><td colspan="3">200 236</td><td colspan="2">226 261</td><td colspan="2">299 334</td><td colspan="2">348 395</td><td colspan="3">407 424</td><td colspan="2">435 508</td></tr>
<tr><td>12</td><td>6000</td><td colspan="2">- -</td><td colspan="2">- -</td><td colspan="3">- -</td><td colspan="2">217 254</td><td colspan="3">250 304</td><td colspan="2">261 294</td><td colspan="2">334 365</td><td colspan="2">396 435</td><td colspan="3">452 496</td><td colspan="2">487 565</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td colspan="2">н о</td><td colspan="2">п р</td><td>с</td><td colspan="2">т</td><td>у</td><td>ф</td></tr>
<tr><td colspan="25">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td>1.</td><td colspan="6">Обрабатываемого материала</td><td colspan="10">Чугун, твердость, НВ, МПа Коэффициент К тв</td><td colspan="3">до 2150 1,0</td><td colspan="5">св. 2150 1,20</td></tr>
<tr><td rowspan="2">2.</td><td colspan="6" rowspan="2">Числа одновременно работающих суппортов</td><td colspan="10">Число одновременно работающих суппортов</td><td colspan="3">1</td><td colspan="5">2</td></tr>
<tr><td colspan="5">Коэффициент К при рс обработке</td><td colspan="5">одной поверхности нескольких поверхностей</td><td colspan="3">1,0 1,0</td><td colspan="5">0,6 1,2</td></tr>
<tr><td>3.</td><td colspan="6">Отношения скорости рабочего хода к холостому</td><td colspan="10">Отношение скорости рабочего хода к холостому, до Коэффициент К m</td><td colspan="2">0,2 0,83</td><td colspan="3">0,5 1,0</td><td colspan="3">0,7 1,1</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="15%"><col width="9%"><col width="11%"><col width="8%"><col width="12%"><col width="9%"><col width="11%"><col width="3%"><col width="5%"><col width="11%"></colgroup>
<tr><td colspan="11">Неполное штучное время Продольно-строгальные Строгание угловых и прямоугольных станки смазочных канавок</td></tr>
<tr><td colspan="11">Чугун серый, НВ = 1760...2150 МПа Резцы с пластинками ВК8</td></tr>
<tr><td colspan="11">Карта 42</td></tr>
<tr><td colspan="11">рисунок не приводится</td></tr>
<tr><td rowspan="5">N позиции</td><td>Длина канавки,</td><td colspan="9">Ширина канавки, В, мм, до</td></tr>
<tr><td rowspan="4">l, мм, до</td><td colspan="2">3 - 4</td><td colspan="2">5 - 7</td><td colspan="2">8 - 10</td><td colspan="3">св. 10</td></tr>
<tr><td colspan="9">Глубина канавки, h, мм, до</td></tr>
<tr><td colspan="2">3</td><td colspan="2">4</td><td colspan="2">5</td><td colspan="3">6</td></tr>
<tr><td colspan="9">Время на канавку, t , мин. нш</td></tr>
<tr><td>1</td><td>200</td><td colspan="2">4,5</td><td colspan="2">5,5</td><td colspan="2">6,5</td><td colspan="3">7,0</td></tr>
<tr><td>2</td><td>500</td><td colspan="2">5,0</td><td colspan="2">6,0</td><td colspan="2">7,0</td><td colspan="3">8,0</td></tr>
<tr><td>3</td><td>750</td><td colspan="2">6,0</td><td colspan="2">6,5</td><td colspan="2">8,0</td><td colspan="3">9,0</td></tr>
<tr><td>4</td><td>1000</td><td colspan="2">6,5</td><td colspan="2">7,0</td><td colspan="2">9,0</td><td colspan="3">10</td></tr>
<tr><td>5</td><td>1250</td><td colspan="2">7,0</td><td colspan="2">8,0</td><td colspan="2">10</td><td colspan="3">11,5</td></tr>
<tr><td>6</td><td>1500</td><td colspan="2">8,5</td><td colspan="2">10</td><td colspan="2">13</td><td colspan="3">15,5</td></tr>
<tr><td>7</td><td>2000</td><td colspan="2">10</td><td colspan="2">12</td><td colspan="2">17</td><td colspan="3">20</td></tr>
<tr><td>8</td><td>2500</td><td colspan="2">12</td><td colspan="2">15</td><td colspan="2">20</td><td colspan="3">22</td></tr>
<tr><td>9</td><td>3000</td><td colspan="2">13</td><td colspan="2">17</td><td colspan="2">22</td><td colspan="3">25</td></tr>
<tr><td>10</td><td>3500</td><td colspan="2">16</td><td colspan="2">20</td><td colspan="2">25</td><td colspan="3">27</td></tr>
<tr><td>11</td><td>4000</td><td colspan="2">18</td><td colspan="2">22</td><td colspan="2">27</td><td colspan="3">30</td></tr>
<tr><td>12</td><td>5000</td><td colspan="2">21</td><td colspan="2">25</td><td colspan="2">30</td><td colspan="3">34</td></tr>
<tr><td>13</td><td>6000</td><td colspan="2">23</td><td colspan="2">29</td><td colspan="2">36</td><td colspan="3">39</td></tr>
<tr><td colspan="2">Индекс</td><td colspan="2">а</td><td colspan="2">б</td><td colspan="2">в</td><td colspan="3">г</td></tr>
<tr><td colspan="11">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td>1.</td><td colspan="2">Обрабатываемого материала</td><td colspan="4">Чугун, твердость, НВ, МПа Коэффициент К тв</td><td colspan="2">до 2150 1,0</td><td colspan="2">св. 2150 1,2</td></tr>
<tr><td rowspan="2">2.</td><td colspan="2">Числа одновременно работающих</td><td colspan="4">Число одновременно работающих суппортов</td><td colspan="2">1</td><td colspan="2">2</td></tr>
<tr><td colspan="2">суппортов</td><td colspan="2">Коэффициент при обработке К рс</td><td colspan="2">одной поверхности нескольких поверхностей</td><td colspan="2">1,0 1,0</td><td colspan="2">0,6 1,2</td></tr>
<tr><td rowspan="2">3.</td><td colspan="2" rowspan="2">Отношения скорости рабочего хода к холостому</td><td colspan="4" rowspan="2">Отношение скорости рабочего хода к холостому, до Коэффициент К m</td><td colspan="3">0,2 0,5</td><td>0,7</td></tr>
<tr><td colspan="3">0,83 1,0</td><td>1,1</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="6%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="23">Неполное штучное время Продольно-строгальные станки</td></tr>
<tr><td colspan="23">Сталь конструкционная, сигма = 590...740 МПа Резцы из стали Р6М5</td></tr>
<tr><td colspan="23">Карта 43 лист 1</td></tr>
<tr><td colspan="23">рисунок не приводится</td></tr>
<tr><td rowspan="4">N позиции</td><td>Характер</td><td>Ширина</td><td colspan="10">Заготовка из проката</td><td colspan="10">Поковка или отливка</td></tr>
<tr><td rowspan="3">обработки</td><td rowspan="2">обрабатываемой</td><td colspan="20">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>200</td><td>500</td><td>1000</td><td>1500</td><td>2000</td><td>2500</td><td>3000</td><td>4000</td><td>5000</td><td>6000</td><td>200</td><td>500</td><td>1000</td><td>1500</td><td>2000</td><td>2500</td><td>3000</td><td>4000</td><td>5000</td><td>6000</td></tr>
<tr><td>поверхности, В, мм</td><td colspan="20">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>50</td><td>7</td><td>11</td><td>15</td><td>21</td><td>26</td><td>33</td><td>40</td><td>48</td><td>59</td><td>69</td><td>15</td><td>23</td><td>33</td><td>44</td><td>54</td><td>70</td><td>84</td><td>102</td><td>124</td><td>146</td></tr>
<tr><td>2</td><td>14...</td><td>75</td><td>8</td><td>12</td><td>19</td><td>24</td><td>31</td><td>39</td><td>47</td><td>58</td><td>72</td><td>84</td><td>17</td><td>26</td><td>40</td><td>52</td><td>65</td><td>82</td><td>99</td><td>122</td><td>151</td><td>175</td></tr>
<tr><td>3</td><td>12</td><td>100</td><td>10</td><td>15</td><td>24</td><td>32</td><td>41</td><td>52</td><td>63</td><td>76</td><td>90</td><td>111</td><td>20</td><td>28</td><td>50</td><td>67</td><td>87</td><td>110</td><td>131</td><td>162</td><td>189</td><td>233</td></tr>
<tr><td>4</td><td>квали-</td><td>150</td><td>12</td><td>20</td><td>32</td><td>44</td><td>55</td><td>71</td><td>85</td><td>104</td><td>132</td><td>154</td><td>25</td><td>43</td><td>67</td><td>92</td><td>117</td><td>149</td><td>178</td><td>214</td><td>277</td><td>322</td></tr>
<tr><td>5</td><td>тет</td><td>200</td><td>15</td><td>26</td><td>43</td><td>58</td><td>75</td><td>96</td><td>115</td><td>144</td><td>177</td><td>211</td><td>31</td><td>54</td><td>90</td><td>122</td><td>158</td><td>204</td><td>245</td><td>304</td><td>373</td><td>442</td></tr>
<tr><td>6</td><td></td><td>250</td><td>-</td><td>33</td><td>54</td><td>74</td><td>95</td><td>122</td><td>145</td><td>186</td><td>227</td><td>269</td><td>-</td><td>70</td><td>112</td><td>154</td><td>200</td><td>259</td><td>304</td><td>386</td><td>477</td><td>560</td></tr>
<tr><td>7</td><td></td><td>300</td><td>-</td><td>39</td><td>66</td><td>92</td><td>115</td><td>146</td><td>178</td><td>223</td><td>273</td><td>318</td><td>-</td><td>94</td><td>140</td><td>195</td><td>241</td><td>309</td><td>377</td><td>473</td><td>582</td><td>669</td></tr>
<tr><td>8</td><td></td><td>350</td><td>-</td><td>45</td><td>74</td><td>103</td><td>136</td><td>174</td><td>209</td><td>259</td><td>325</td><td>377</td><td>-</td><td>94</td><td>158</td><td>218</td><td>286</td><td>368</td><td>436</td><td>545</td><td>682</td><td>795</td></tr>
<tr><td>9</td><td></td><td>400</td><td>-</td><td>50</td><td>85</td><td>118</td><td>154</td><td>200</td><td>236</td><td>300</td><td>372</td><td>440</td><td>-</td><td>103</td><td>179</td><td>250</td><td>327</td><td>423</td><td>500</td><td>636</td><td>777</td><td>922</td></tr>
<tr><td>10</td><td></td><td>500</td><td>-</td><td>59</td><td>110</td><td>150</td><td>204</td><td>236</td><td>285</td><td>368</td><td>468</td><td>550</td><td>-</td><td>124</td><td>209</td><td>318</td><td>413</td><td>500</td><td>600</td><td>782</td><td>982</td><td>1154</td></tr>
<tr><td>11</td><td></td><td>600</td><td>-</td><td>-</td><td>123</td><td>176</td><td>218</td><td>286</td><td>345</td><td>436</td><td>540</td><td>636</td><td>-</td><td>153</td><td>259</td><td>373</td><td>464</td><td>600</td><td>718</td><td>918</td><td>1136</td><td>1336</td></tr>
<tr><td>12</td><td></td><td>700</td><td>-</td><td>-</td><td>144</td><td>204</td><td>264</td><td>336</td><td>414</td><td>509</td><td>636</td><td>750</td><td>-</td><td>178</td><td>304</td><td>436</td><td>554</td><td>718</td><td>872</td><td>1082</td><td>1336</td><td>1564</td></tr>
<tr><td>13</td><td></td><td>800</td><td>-</td><td>-</td><td>165</td><td>236</td><td>304</td><td>404</td><td>464</td><td>591</td><td>827</td><td>864</td><td>-</td><td>204</td><td>345</td><td>491</td><td>636</td><td>854</td><td>982</td><td>1245</td><td>1536</td><td>1818</td></tr>
<tr><td>14</td><td></td><td>1000</td><td>-</td><td>-</td><td>209</td><td>296</td><td>395</td><td>491</td><td>582</td><td>745</td><td>895</td><td>1073</td><td>-</td><td>247</td><td>436</td><td>618</td><td>827</td><td>1036</td><td>1227</td><td>1564</td><td>1873</td><td>2254</td></tr>
<tr><td colspan="3">Число проходов</td><td colspan="10">1</td><td colspan="10">2</td></tr>
<tr><td>15</td><td>Rz 40;</td><td>50</td><td>14</td><td>19</td><td>25</td><td>32</td><td>38</td><td>47</td><td>56</td><td>68</td><td>83</td><td>95</td><td>21</td><td>31</td><td>43</td><td>54</td><td>67</td><td>84</td><td>100</td><td>122</td><td>147</td><td>166</td></tr>
<tr><td>16</td><td>11</td><td>75</td><td>15</td><td>23</td><td>30</td><td>38</td><td>47</td><td>58</td><td>68</td><td>84</td><td>102</td><td>119</td><td>24</td><td>35</td><td>56</td><td>65</td><td>81</td><td>100</td><td>122</td><td>148</td><td>182</td><td>211</td></tr>
<tr><td>17</td><td>квали-</td><td>100</td><td>17</td><td>26</td><td>36</td><td>47</td><td>60</td><td>75</td><td>89</td><td>109</td><td>136</td><td>156</td><td>25</td><td>40</td><td>63</td><td>84</td><td>106</td><td>133</td><td>157</td><td>194</td><td>227</td><td>278</td></tr>
<tr><td>18</td><td>тет</td><td>150</td><td>21</td><td>34</td><td>48</td><td>65</td><td>82</td><td>103</td><td>120</td><td>150</td><td>180</td><td>203</td><td>34</td><td>56</td><td>84</td><td>114</td><td>143</td><td>181</td><td>214</td><td>350</td><td>331</td><td>386</td></tr>
<tr><td>19</td><td></td><td>200</td><td>25</td><td>44</td><td>63</td><td>84</td><td>107</td><td>137</td><td>161</td><td>214</td><td>236</td><td>267</td><td>42</td><td>71</td><td>110</td><td>147</td><td>190</td><td>245</td><td>291</td><td>373</td><td>444</td><td>524</td></tr>
<tr><td>20</td><td></td><td>250</td><td>-</td><td>53</td><td>76</td><td>105</td><td>135</td><td>172</td><td>200</td><td>254</td><td>309</td><td>349</td><td>-</td><td>90</td><td>136</td><td>186</td><td>236</td><td>309</td><td>359</td><td>464</td><td>568</td><td>652</td></tr>
<tr><td>21</td><td></td><td>300</td><td>-</td><td>62</td><td>94</td><td>129</td><td>161</td><td>204</td><td>245</td><td>304</td><td>379</td><td>441</td><td>-</td><td>105</td><td>167</td><td>232</td><td>282</td><td>364</td><td>441</td><td>554</td><td>664</td><td>782</td></tr>
<tr><td>22</td><td></td><td>350</td><td>-</td><td>71</td><td>104</td><td>144</td><td>186</td><td>236</td><td>280</td><td>354</td><td>409</td><td>536</td><td>-</td><td>121</td><td>186</td><td>259</td><td>336</td><td>432</td><td>509</td><td>636</td><td>790</td><td>936</td></tr>
<tr><td>23</td><td></td><td>400</td><td>-</td><td>82</td><td>119</td><td>164</td><td>209</td><td>273</td><td>323</td><td>409</td><td>506</td><td>596</td><td>-</td><td>136</td><td>209</td><td>295</td><td>382</td><td>500</td><td>591</td><td>736</td><td>918</td><td>1022</td></tr>
<tr><td>24</td><td></td><td>500</td><td>-</td><td>98</td><td>142</td><td>204</td><td>268</td><td>327</td><td>390</td><td>500</td><td>604</td><td>745</td><td>-</td><td>163</td><td>250</td><td>373</td><td>482</td><td>582</td><td>700</td><td>909</td><td>1145</td><td>1345</td></tr>
<tr><td colspan="3">Число проходов</td><td colspan="10">2</td><td colspan="10">3</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td>у</td><td>ф</td></tr>
</table>



```text
┌───────────────────────────────────────────────────────┬────────────────────────────────────────────────────────┐
│                Неполное штучное время                 │              Продольно-строгальные станки              │
│                 Строгание плоскостей                  ├────────────────────────────────────────────────────────┤
│    Сталь конструкционная, сигма  = 590...740 МПа      │                  Резцы из стали Р6М5                   │
│                                в                      ├───────────────────────────┬────────────────────────────┤
│                                                       │         Карта 43          │           лист 2           │
├───┬──────┬─────┬──────────────────────────────────────┴────────┬──────────────────┴────────────────────────────┤
│N  │Харак-│Шири-│              Заготовка из проката             │             Поковка или отливка               │
│по-│тер   │на   ├───────────────────────────────────────────────┴───────────────────────────────────────────────┤
│зи-│обра- │обра-│                           Длина обрабатываемой поверхности, l, мм, до                         │
│ции│ботки │баты-├───┬───┬────┬────┬────┬────┬────┬────┬────┬────┬───┬───┬────┬────┬────┬────┬────┬────┬────┬────┤
│   │      │вае- │200│500│1000│1500│2000│2500│3000│4000│5000│6000│200│500│1000│1500│2000│2500│3000│4000│5000│6000│
│   │      │мой  ├───┴───┴────┴────┴────┴────┴────┴────┴────┴────┴───┴───┴────┴────┴────┴────┴────┴────┴────┴────┤
│   │      │пове-│                               Время на поверхность, t  , мин.                                 │
│   │      │рхно-│                                                      нш                                       │
│   │      │сти, │                                                                                               │
│   │      │В,   │                                                                                               │
│   │      │мм,  │                                                                                               │
│   │      │до   │                                                                                               │
├───┼──────┼─────┼───┬───┬────┬────┬────┬────┬────┬────┬────┬────┬───┬───┬────┬────┬────┬────┬────┬────┬────┬────┤
│25 │Rz 40;│600  │ - │ - │171 │245 │300 │382 │473 │600 │695 │873 │ - │ - │309 │436 │545 │709 │845 │1082│1336│1568│
│26 │11    │700  │ - │ - │200 │282 │364 │464 │554 │700 │827 │1018│ - │ - │359 │509 │654 │836 │991 │1273│1573│1832│
│27 │квали-│800  │ - │ - │227 │323 │414 │545 │627 │809 │945 │1164│ - │ - │409 │582 │745 │1018│1173│1454│1809│2154│
│28 │тет   │1000 │ - │ - │287 │404 │532 │668 │786 │850 │1154│1464│ - │ - │532 │740 │972 │1182│1427│1818│2254│2573│
├───┴──────┴─────┼───┴───┴────┴────┴────┴────┴────┴────┴────┴────┼───┴───┴────┴────┴────┴────┴────┴────┴────┴────┤
│Число проходов, │2                                              │3                                              │
├────────────────┼───┬───┬────┬────┬────┬────┬────┬────┬────┬────┼───┬───┬────┬────┬────┬────┬────┬────┬────┬────┤
│Индекс          │ а │ б │ в  │ г  │ д  │ е  │ ж  │ з  │ и  │ к  │ л │ м │ н  │ о  │ п  │ р  │ с  │ т  │ у  │  ф │
├────────────────┴───┴───┴────┴────┴────┴────┴────┴────┴────┴────┴───┴───┴────┴────┴────┴────┴────┴────┴────┴────┤
│Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:                     │
├───┬──────────────────┬──────────────────┬───────────────────────────────┬───────────────────┬──────────────────┤
│1. │Обрабатываемого   │Группа стали      │Углеродистые конструкционные   │Коррозионностойкие │Жаропрочные       │
│   │материала         ├──────────────────┼────────┬────────────┬─────────┼───────────────────┼──────────────────┤
│   │                  │Предел прочности, │до 590  │590...740   │св. 740  │                   │                  │
│   │                  │сигма , МПа       │        │            │         │                   │                  │
│   │                  │     в            │        │            │         │                   │                  │
│   │                  │Коэффициент К     │0,9     │1,0         │1,2      │1,35               │1,45              │
│   │                  │             пп   │        │            │         │                   │                  │
├───┼──────────────────┼──────────────────┼────────┴────────────┴─────────┴────────┬──────────┴──────────────────┤
│2. │Угла в плане резца│фи, град.         │45...60                                 │50                           │
│   │                  │Коэффициент К     │1,0                                     │1,4                          │
│   │                  │             фи   │                                        │                             │
├───┼──────────────────┼──────────────────┴─────────────────────┬──────────────────┼─────────────────────────────┤
│3. │Числа одновременно│Число одновременно работающих суппортов │1                 │2                            │
│   │работающих        ├────────────────┬───────────────────────┼──────────────────┼─────────────────────────────┤
│   │суппортов         │Коэффициенты при│одной поверхности      │1,0               │0,6                          │
│   │                  │обработке К     │нескольких поверхностей│1,0               │1,2                          │
│   │                  │           рс   │                       │                  │                             │
├───┼──────────────────┼────────────────┴───────────────────────┼─────────┬────────┴─────────┬───────────────────┤
│4. │Отношения скорости│Отношение скорости рабочего хода к      │0,2      │0,5               │0,7                │
│   │рабочего хода к   │холостому                               │         │                  │                   │
│   │холостому         │Коэффициент К                           │0,83     │1,0               │1,1                │
│   │                  │             m                          │         │                  │                   │
└───┴──────────────────┴────────────────────────────────────────┴─────────┴──────────────────┴───────────────────┘
```



<table>
<colgroup><col width="4%"><col width="6%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="11">Неполное штучное время Строгание плоскостей</td><td colspan="12">Продольно-строгальные станки</td></tr>
<tr><td colspan="11" rowspan="2">Сталь конструкционная, сигма = 590...740 МПа в</td><td colspan="12">Резцы с пластинками Т5К10</td></tr>
<tr><td colspan="6">Карта 44</td><td colspan="6">лист 1</td></tr>
<tr><td colspan="23">рисунок не приводится</td></tr>
<tr><td rowspan="4">N позиции</td><td>Характер</td><td>Ширина</td><td colspan="10">Заготовка из проката</td><td colspan="10">Поковка или отливка</td></tr>
<tr><td rowspan="3">обработки</td><td rowspan="2">обрабатываемой</td><td colspan="20">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>200</td><td>500</td><td>1000</td><td>1500</td><td>2000</td><td>2500</td><td>3000</td><td>4000</td><td>5000</td><td>6000</td><td>200</td><td>500</td><td>1000</td><td>1500</td><td>2000</td><td>2500</td><td>3000</td><td>4000</td><td>5000</td><td>6000</td></tr>
<tr><td>поверхности, В, мм, до</td><td colspan="20">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>50</td><td>5</td><td>7</td><td>9</td><td>11</td><td>13</td><td>15</td><td>19</td><td>23</td><td>26</td><td>29</td><td>11</td><td>15</td><td>19</td><td>24</td><td>28</td><td>32</td><td>40</td><td>49</td><td>56</td><td>61</td></tr>
<tr><td>2</td><td>14...</td><td>75</td><td>6</td><td>8</td><td>11</td><td>13</td><td>16</td><td>19</td><td>23</td><td>27</td><td>31</td><td>36</td><td>12</td><td>16</td><td>22</td><td>27</td><td>33</td><td>36</td><td>47</td><td>56</td><td>71</td><td>74</td></tr>
<tr><td>3</td><td>12</td><td>100</td><td>7</td><td>9</td><td>13</td><td>16</td><td>18</td><td>23</td><td>28</td><td>35</td><td>44</td><td>45</td><td>13</td><td>18</td><td>26</td><td>33</td><td>39</td><td>47</td><td>54</td><td>74</td><td>92</td><td>105</td></tr>
<tr><td>4</td><td>квали-</td><td>150</td><td>8</td><td>11</td><td>15</td><td>20</td><td>25</td><td>31</td><td>35</td><td>48</td><td>59</td><td>70</td><td>15</td><td>23</td><td>32</td><td>44</td><td>54</td><td>64</td><td>74</td><td>102</td><td>119</td><td>136</td></tr>
<tr><td>5</td><td>тет</td><td>200</td><td>9</td><td>13</td><td>21</td><td>27</td><td>34</td><td>40</td><td>50</td><td>65</td><td>76</td><td>85</td><td>18</td><td>29</td><td>44</td><td>53</td><td>72</td><td>94</td><td>97</td><td>136</td><td>156</td><td>176</td></tr>
<tr><td>6</td><td></td><td>250</td><td>-</td><td>16</td><td>25</td><td>34</td><td>43</td><td>50</td><td>64</td><td>82</td><td>100</td><td>105</td><td>-</td><td>34</td><td>54</td><td>72</td><td>89</td><td>103</td><td>122</td><td>172</td><td>207</td><td>220</td></tr>
<tr><td>7</td><td></td><td>300</td><td>-</td><td>19</td><td>31</td><td>40</td><td>51</td><td>59</td><td>70</td><td>98</td><td>119</td><td>127</td><td>-</td><td>40</td><td>64</td><td>84</td><td>107</td><td>124</td><td>146</td><td>209</td><td>250</td><td>267</td></tr>
<tr><td>8</td><td></td><td>350</td><td>-</td><td>22</td><td>35</td><td>47</td><td>62</td><td>70</td><td>80</td><td>113</td><td>139</td><td>149</td><td>-</td><td>45</td><td>74</td><td>99</td><td>129</td><td>146</td><td>169</td><td>236</td><td>294</td><td>309</td></tr>
<tr><td>9</td><td></td><td>400</td><td>-</td><td>24</td><td>39</td><td>54</td><td>67</td><td>79</td><td>93</td><td>130</td><td>161</td><td>171</td><td>-</td><td>52</td><td>82</td><td>112</td><td>142</td><td>166</td><td>195</td><td>273</td><td>336</td><td>356</td></tr>
<tr><td>10</td><td></td><td>500</td><td>-</td><td>29</td><td>48</td><td>66</td><td>84</td><td>99</td><td>115</td><td>161</td><td>200</td><td>213</td><td>-</td><td>62</td><td>102</td><td>139</td><td>176</td><td>209</td><td>236</td><td>336</td><td>418</td><td>445</td></tr>
<tr><td>11</td><td></td><td>600</td><td>-</td><td>-</td><td>56</td><td>77</td><td>98</td><td>114</td><td>132</td><td>186</td><td>233</td><td>247</td><td>-</td><td>-</td><td>119</td><td>160</td><td>209</td><td>241</td><td>277</td><td>395</td><td>491</td><td>523</td></tr>
<tr><td>12</td><td></td><td>700</td><td>-</td><td>-</td><td>66</td><td>90</td><td>114</td><td>134</td><td>155</td><td>218</td><td>273</td><td>289</td><td>-</td><td>-</td><td>139</td><td>190</td><td>236</td><td>282</td><td>327</td><td>463</td><td>573</td><td>609</td></tr>
<tr><td>13</td><td></td><td>800</td><td>-</td><td>-</td><td>75</td><td>103</td><td>130</td><td>153</td><td>177</td><td>250</td><td>314</td><td>330</td><td>-</td><td>-</td><td>159</td><td>218</td><td>273</td><td>318</td><td>372</td><td>527</td><td>663</td><td>718</td></tr>
<tr><td>14</td><td></td><td>1000</td><td>-</td><td>-</td><td>94</td><td>129</td><td>163</td><td>191</td><td>212</td><td>350</td><td>395</td><td>418</td><td>-</td><td>-</td><td>198</td><td>273</td><td>343</td><td>400</td><td>468</td><td>663</td><td>827</td><td>882</td></tr>
<tr><td colspan="3">Число проходов</td><td colspan="10">1</td><td colspan="10">2</td></tr>
<tr><td>15</td><td>Rz 40;</td><td>50</td><td>10</td><td>13</td><td>17</td><td>20</td><td>24</td><td>27</td><td>34</td><td>41</td><td>49</td><td>53</td><td>16</td><td>21</td><td>26</td><td>33</td><td>39</td><td>43</td><td>54</td><td>66</td><td>81</td><td>85</td></tr>
<tr><td>16</td><td>14...</td><td>75</td><td>11</td><td>14,5</td><td>18</td><td>23</td><td>27</td><td>32</td><td>40</td><td>48</td><td>59</td><td>64</td><td>17</td><td>23</td><td>30</td><td>37</td><td>44</td><td>51</td><td>64</td><td>78</td><td>96</td><td>103</td></tr>
<tr><td>17</td><td>12</td><td>100</td><td>12</td><td>17</td><td>23</td><td>29</td><td>34</td><td>40</td><td>48</td><td>63</td><td>74</td><td>83</td><td>19</td><td>26</td><td>36</td><td>46</td><td>54</td><td>64</td><td>76</td><td>102</td><td>120</td><td>133</td></tr>
<tr><td>18</td><td>квали-</td><td>150</td><td>15</td><td>21</td><td>27</td><td>37</td><td>46</td><td>55</td><td>65</td><td>85</td><td>103</td><td>114</td><td>23</td><td>34</td><td>44</td><td>61</td><td>74</td><td>89</td><td>104</td><td>136</td><td>167</td><td>182</td></tr>
<tr><td>19</td><td>тет</td><td>200</td><td>17</td><td>26</td><td>37</td><td>48</td><td>60</td><td>72</td><td>85</td><td>113</td><td>138</td><td>151</td><td>27</td><td>42</td><td>61</td><td>78</td><td>98</td><td>116</td><td>136</td><td>182</td><td>225</td><td>245</td></tr>
<tr><td>20</td><td></td><td>250</td><td>-</td><td>31</td><td>45</td><td>60</td><td>74</td><td>90</td><td>104</td><td>142</td><td>174</td><td>190</td><td>-</td><td>49</td><td>74</td><td>107</td><td>121</td><td>143</td><td>169</td><td>232</td><td>286</td><td>305</td></tr>
<tr><td>21</td><td></td><td>300</td><td>-</td><td>35</td><td>54</td><td>71</td><td>90</td><td>106</td><td>126</td><td>172</td><td>207</td><td>231</td><td>-</td><td>56</td><td>87</td><td>115</td><td>145</td><td>172</td><td>204</td><td>282</td><td>336</td><td>370</td></tr>
<tr><td>22</td><td></td><td>350</td><td>-</td><td>40</td><td>62</td><td>82</td><td>106</td><td>125</td><td>146</td><td>200</td><td>244</td><td>271</td><td>-</td><td>64</td><td>100</td><td>132</td><td>173</td><td>200</td><td>236</td><td>323</td><td>398</td><td>436</td></tr>
<tr><td>23</td><td></td><td>400</td><td>-</td><td>45</td><td>68</td><td>94</td><td>117</td><td>142</td><td>169</td><td>227</td><td>278</td><td>308</td><td>-</td><td>73</td><td>112</td><td>152</td><td>191</td><td>227</td><td>273</td><td>368</td><td>454</td><td>495</td></tr>
<tr><td>24</td><td></td><td>500</td><td>-</td><td>55</td><td>84</td><td>115</td><td>146</td><td>178</td><td>209</td><td>282</td><td>347</td><td>385</td><td>-</td><td>88</td><td>137</td><td>186</td><td>236</td><td>286</td><td>336</td><td>454</td><td>568</td><td>618</td></tr>
<tr><td colspan="3">Число проходов</td><td colspan="10">2</td><td colspan="10">3</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td>у</td><td>ф</td></tr>
</table>



```text
┌───────────────────────────────────────────────────────┬─────────────────────────────────────────────────────────┐
│                Неполное штучное время                 │              Продольно-строгальные станки               │
│                 Строгание плоскостей                  ├─────────────────────────────────────────────────────────┤
│    Сталь конструкционная, сигма  = 590...740 МПа      │               Резцы с пластинками Т5К10                 │
│                                в                      ├───────────────────────────┬─────────────────────────────┤
│                                                       │         Карта 44          │           лист 2            │
├───┬──────┬─────┬──────────────────────────────────────┴─────────┬─────────────────┴─────────────────────────────┤
│N  │Харак-│Шири-│              Заготовка из проката              │            Поковка или отливка                │
│по-│тер   │на   ├────────────────────────────────────────────────┴───────────────────────────────────────────────┤
│зи-│обра- │обра-│                           Длина обрабатываемой поверхности, l, мм, до                          │
│ции│ботки │баты-├───┬────┬────┬────┬────┬────┬────┬────┬────┬────┬───┬───┬────┬────┬────┬────┬────┬────┬────┬────┤
│   │      │вае- │200│500 │1000│1500│2000│2500│3000│4000│5000│6000│200│500│1000│1500│2000│2500│3000│4000│5000│6000│
│   │      │мой  ├───┴────┴────┴────┴────┴────┴────┴────┴────┴────┴───┴───┴────┴────┴────┴────┴────┴────┴────┴────┤
│   │      │пове-│                                Время на поверхность, t  , мин.                                 │
│   │      │рхно-│                                                       нш                                       │
│   │      │сти, │                                                                                                │
│   │      │В,   │                                                                                                │
│   │      │мм,  │                                                                                                │
│   │      │до   │                                                                                                │
├───┼──────┼─────┼───┬────┬────┬────┬────┬────┬────┬────┬────┬────┬───┬───┬────┬────┬────┬────┬────┬────┬────┬────┤
│25 │Rz 40;│600  │ - │ -  │98  │133 │171 │204 │241 │323 │404 │449 │ - │ - │161 │218 │277 │332 │386 │527 │663 │723 │
│26 │11    │700  │ - │ -  │114 │154 │200 │241 │282 │386 │473 │525 │ - │ - │186 │254 │323 │391 │454 │627 │785 │845 │
│27 │квали-│800  │ - │ -  │130 │178 │227 │273 │323 │441 │543 │603 │ - │ - │214 │290 │368 │441 │518 │718 │891 │964 │
│28 │тет   │1000 │ - │ -  │162 │222 │285 │343 │404 │550 │682 │762 │ - │ - │265 │363 │464 │554 │650 │900 │1109│1227│
├───┴──────┴─────┼───┴────┴────┴────┴────┴────┴────┴────┴────┴────┼───┴───┴────┴────┴────┴────┴────┴────┴────┴────┤
│Число проходов  │2                                               │3                                              │
├────────────────┼───┬────┬────┬────┬────┬────┬────┬────┬────┬────┼───┬───┬────┬────┬────┬────┬────┬────┬────┬────┤
│Индекс          │ а │ б  │ в  │ г  │ д  │ е  │ ж  │ з  │ и  │ к  │ л │ м │ н  │ о  │ п  │ р  │ с  │ т  │  у │  ф │
├────────────────┴───┴────┴────┴────┴────┴────┴────┴────┴────┴────┴───┴───┴────┴────┴────┴────┴────┴────┴────┴────┤
│Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:                      │
├───┬──────────────────┬─────────────────┬─────────────────────────────────┬──────────────────┬───────────────────┤
│1. │Обрабатываемого   │Группа стали     │Углеродистые конструкционные     │Коррозионностойкие│Жаропрочные        │
│   │материала         ├─────────────────┼────────┬──────────────┬─────────┼──────────────────┼───────────────────┤
│   │                  │Предел прочности,│до 590  │590...740     │св. 740  │                  │                   │
│   │                  │сигма , МПа      │        │              │         │                  │                   │
│   │                  │     в           │        │              │         │                  │                   │
│   │                  │Коэффициент К    │0,9     │1,0           │1,2      │1,35              │1,45               │
│   │                  │             пп  │        │              │         │                  │                   │
├───┼──────────────────┼─────────────────┼────────┴──────────────┴─────────┴─────┬────────────┴───────────────────┤
│2. │Угла в плане резца│фи, град.        │45...60                                │90                              │
│   │                  │Коэффициент К    │1,0                                    │1,4                             │
│   │                  │             фи  │                                       │                                │
├───┼──────────────────┼─────────────────┴───────────────────────┬───────────────┼────────────────────────────────┤
│3. │Числа одновременно│Число одновременно работающих суппортов  │1              │2                               │
│   │работающих        ├─────────────────┬───────────────────────┼───────────────┼────────────────────────────────┤
│   │суппортов         │Коэффициент при  │одной поверхности      │1,0            │0,6                             │
│   │                  │обработке К      │нескольких             │1,0            │1,2                             │
│   │                  │           рс    │поверхностей           │               │                                │
├───┼──────────────────┼─────────────────┴───────────────────────┼──────────┬────┴──────┬─────────────────────────┤
│4. │Отношения скорости│Отношение скорости рабочего хода к       │0,2       │0,5        │0,7                      │
│   │рабочего хода к   │холостому, до                            │          │           │                         │
│   │холостому         │Коэффициент К                            │0,83      │1,0        │1,1                      │
│   │                  │             m                           │          │           │                         │
└───┴──────────────────┴─────────────────────────────────────────┴──────────┴───────────┴─────────────────────────┘
```



<table>
<colgroup><col width="5%"><col width="8%"><col width="5%"><col width="3%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="4%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="17">Неполное штучное время Продольно-строгальные станки Строгание прямоугольных пазов, Rz 80; 14...12 квалитет Резцы с пластинками Р6М5 Сталь конструкционная, сигма = 590...740 МПа Карта 45 в</td></tr>
<tr><td colspan="17">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина</td><td colspan="2">Глубина</td><td>Число</td><td colspan="12">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>паза, В,</td><td colspan="2">паза, Н,</td><td rowspan="2">проходов, i</td><td>200</td><td>500</td><td>750</td><td>1000</td><td>1500</td><td>2000</td><td>2500</td><td>3000</td><td colspan="2">4000</td><td>5000</td><td>6000</td></tr>
<tr><td>мм, до</td><td colspan="2">мм, до</td><td colspan="12">Время на паз t , мин. нш</td></tr>
<tr><td>1</td><td>10</td><td colspan="2">5</td><td>1</td><td>7</td><td>8</td><td>9</td><td>10</td><td>12</td><td>15</td><td>18</td><td>23</td><td colspan="2">26</td><td>32</td><td>36</td></tr>
<tr><td>2</td><td></td><td colspan="2">12</td><td></td><td>10</td><td>12</td><td>13</td><td>15</td><td>20</td><td>24</td><td>32</td><td>40</td><td colspan="2">47</td><td>59</td><td>68</td></tr>
<tr><td>3</td><td></td><td colspan="2">20</td><td></td><td>12</td><td>16</td><td>18</td><td>23</td><td>30</td><td>36</td><td>48</td><td>60</td><td colspan="2">71</td><td>86</td><td>104</td></tr>
<tr><td>4</td><td>15</td><td colspan="2">10</td><td>1</td><td>9</td><td>11</td><td>12</td><td>14</td><td>18</td><td>22</td><td>27</td><td>34</td><td colspan="2">41</td><td>50</td><td>59</td></tr>
<tr><td>5</td><td></td><td colspan="2">20</td><td></td><td>12</td><td>16</td><td>18</td><td>23</td><td>28</td><td>30</td><td>47</td><td>59</td><td colspan="2">72</td><td>87</td><td>104</td></tr>
<tr><td>6</td><td></td><td colspan="2">30</td><td></td><td>14</td><td>22</td><td>24</td><td>31</td><td>40</td><td>52</td><td>67</td><td>83</td><td colspan="2">103</td><td>127</td><td>149</td></tr>
<tr><td>7</td><td>20</td><td colspan="2">30</td><td>1</td><td>15</td><td>19</td><td>22</td><td>27</td><td>35</td><td>44</td><td>59</td><td>74</td><td colspan="2">87</td><td>111</td><td>131</td></tr>
<tr><td>8</td><td></td><td colspan="2">40</td><td></td><td>16</td><td>24</td><td>27</td><td>34</td><td>44</td><td>56</td><td>77</td><td>95</td><td colspan="2">114</td><td>144</td><td>170</td></tr>
<tr><td>9</td><td>25</td><td colspan="2">30</td><td>2</td><td>25</td><td>34</td><td>39</td><td>51</td><td>66</td><td>85</td><td>114</td><td>141</td><td colspan="2">173</td><td>227</td><td>254</td></tr>
<tr><td>10</td><td></td><td colspan="2">40</td><td></td><td>31</td><td>44</td><td>51</td><td>65</td><td>85</td><td>110</td><td>150</td><td>173</td><td colspan="2">218</td><td>283</td><td>336</td></tr>
<tr><td>11</td><td>30</td><td colspan="2">40</td><td>2</td><td>31</td><td>44</td><td>51</td><td>65</td><td>85</td><td>110</td><td>150</td><td>173</td><td colspan="2">218</td><td>283</td><td>336</td></tr>
<tr><td>12</td><td></td><td colspan="2">50</td><td></td><td>36</td><td>52</td><td>60</td><td>76</td><td>103</td><td>132</td><td>179</td><td>221</td><td colspan="2">269</td><td>343</td><td>401</td></tr>
<tr><td>13</td><td>40</td><td colspan="2">50</td><td>2</td><td>37</td><td>54</td><td>62</td><td>79</td><td>105</td><td>136</td><td>184</td><td>227</td><td colspan="2">276</td><td>353</td><td>412</td></tr>
<tr><td>14</td><td></td><td colspan="2">70</td><td></td><td>54</td><td>83</td><td>98</td><td>126</td><td>169</td><td>224</td><td>295</td><td>365</td><td colspan="2">457</td><td>559</td><td>664</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3" rowspan="2">1. Обрабатываемого материала</td><td colspan="14">Группа стали Углеродистые конструкци- Коррози- Жароонные онностой- проч-</td></tr>
<tr><td colspan="14">Предел прочности, до 590 590...740 св. 740 сигма , МПа в Коэффициент К 0,9 1,0 1,2 1,35 1,45 пп</td></tr>
<tr><td colspan="3">2. Числа одновременно</td><td colspan="14">Число одновременно работающих суппортов 1 2</td></tr>
<tr><td colspan="3">работающих суппортов</td><td colspan="14">Коэффициент при одной поверхности 1,0 0,6 обработке К нескольких поверх- 1,0 1,2 рс ностей</td></tr>
<tr><td colspan="3">3. Отношения скорости рабочего хода к холостому</td><td colspan="11">Отношение скорости рабочего хода к 0,2 холостому, до Коэффициент К 0,83 m</td><td colspan="3">0,5 0,7 1,0 1,1</td></tr>
</table>



###### <a id="p101471"></a>4.2.2. Поперечно-строгальные станки



<table>
<colgroup><col width="6%"><col width="11%"><col width="11%"><col width="11%"><col width="8%"><col width="8%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="8%"></colgroup>
<tr><td colspan="13">Неполное штучное время Поперечно-строгальные станки Строгание плоскостей</td></tr>
<tr><td colspan="13">Чугун серый, НВ = 1760...2150 МПа Резцы проходные с пластинками ВК8, ВК6</td></tr>
<tr><td colspan="13">Карта 46 лист 1</td></tr>
<tr><td colspan="13">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Характер обработки</td><td rowspan="3">Ширина обрабатываемой поверхности, В, мм, до</td><td rowspan="2">Число рабочих</td><td colspan="8">Длина обрабатываемой поверхности, l, мм</td></tr>
<tr><td>100</td><td>200</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td></tr>
<tr><td>ходов</td><td colspan="8">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Стро-</td><td>Rz 80;</td><td>25</td><td>1</td><td>2,0</td><td>2,3</td><td>2,5</td><td>2,7</td><td>3,2</td><td>3,4</td><td>3,6</td><td>3,8</td></tr>
<tr><td>2</td><td>гание</td><td>14...</td><td>50</td><td></td><td>2,3</td><td>2,5</td><td>2,7</td><td>3,3</td><td>3,8</td><td>4,3</td><td>5,0</td><td>6,0</td></tr>
<tr><td>3</td><td>гори-</td><td>12</td><td>75</td><td></td><td>3,0</td><td>3,2</td><td>3,4</td><td>4,3</td><td>5,0</td><td>5,5</td><td>7,2</td><td>9,5</td></tr>
<tr><td>4</td><td>зонта-</td><td>ква-</td><td>100</td><td></td><td>3,6</td><td>4,0</td><td>4,2</td><td>5,3</td><td>6,0</td><td>7,6</td><td>9,0</td><td>10,5</td></tr>
<tr><td>5</td><td>льных</td><td>литет</td><td>150</td><td></td><td>4,2</td><td>4,7</td><td>5,5</td><td>7,0</td><td>8,6</td><td>10</td><td>12</td><td>14</td></tr>
<tr><td>6</td><td>повер-</td><td></td><td>200</td><td></td><td>5,0</td><td>6,3</td><td>7,0</td><td>9,0</td><td>11</td><td>13</td><td>16</td><td>18</td></tr>
<tr><td>7</td><td>хнос-</td><td></td><td>250</td><td></td><td>6,0</td><td>8,0</td><td>8,5</td><td>11</td><td>14</td><td>16</td><td>19</td><td>23</td></tr>
<tr><td>8</td><td>тей</td><td></td><td>300</td><td></td><td>6,6</td><td>9,0</td><td>10</td><td>13</td><td>17</td><td>20</td><td>23</td><td>27</td></tr>
<tr><td>9</td><td></td><td></td><td>350</td><td></td><td>7,6</td><td>10,5</td><td>12</td><td>15</td><td>20</td><td>23</td><td>26</td><td>32</td></tr>
<tr><td>10</td><td rowspan="2"></td><td></td><td>400</td><td></td><td>8,6</td><td>12</td><td>15</td><td>16</td><td>21</td><td>26</td><td>30</td><td>36</td></tr>
<tr><td>11</td><td>Rz 40,</td><td>25</td><td>2</td><td>5,0</td><td>5,2</td><td>5,4</td><td>6,0</td><td>6,7</td><td>7,0</td><td>8,0</td><td>8,5</td></tr>
<tr><td>12</td><td></td><td>Rz 20;</td><td>50</td><td></td><td>5,4</td><td>5,6</td><td>6,0</td><td>7,0</td><td>8,0</td><td>8,6</td><td>11</td><td>12</td></tr>
<tr><td>13</td><td></td><td>11</td><td>75</td><td></td><td>6,0</td><td>6,7</td><td>7,5</td><td>9,0</td><td>10</td><td>11</td><td>14</td><td>17</td></tr>
<tr><td>14</td><td></td><td>ква-</td><td>100</td><td></td><td>7,5</td><td>8,0</td><td>8,6</td><td>11</td><td>12</td><td>14</td><td>18</td><td>19</td></tr>
<tr><td>15</td><td></td><td>литет</td><td>150</td><td></td><td>8,5</td><td>9,5</td><td>11</td><td>13</td><td>16</td><td>19</td><td>23</td><td>25</td></tr>
<tr><td>16</td><td></td><td></td><td>200</td><td></td><td>10</td><td>13</td><td>14</td><td>17</td><td>21</td><td>25</td><td>30</td><td>33</td></tr>
<tr><td>17</td><td></td><td></td><td>250</td><td></td><td>12,5</td><td>14,5</td><td>16</td><td>21</td><td>26</td><td>30</td><td>36</td><td>41</td></tr>
<tr><td>18</td><td></td><td></td><td>300</td><td></td><td>13</td><td>17</td><td>19</td><td>25</td><td>32</td><td>36</td><td>43</td><td>49</td></tr>
<tr><td>19</td><td></td><td></td><td>350</td><td></td><td>15</td><td>19</td><td>22</td><td>29</td><td>36</td><td>43</td><td>49</td><td>55</td></tr>
<tr><td>20</td><td></td><td></td><td>400</td><td></td><td>18</td><td>21</td><td>24</td><td>33</td><td>41</td><td>48</td><td>57</td><td>65</td></tr>
<tr><td colspan="4">Индекс</td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="11%"><col width="11%"><col width="11%"><col width="8%"><col width="6%"><col width="3%"><col width="9%"><col width="9%"><col width="5%"><col width="3%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="6">Неполное штучное время Строгание плоскостей</td><td colspan="7">Поперечно-строгальные станки</td></tr>
<tr><td colspan="6" rowspan="2">Чугун серый, НВ = 1760...2150 МПа</td><td colspan="7">Резцы проходные с пластинками ВК8, ВК6</td></tr>
<tr><td colspan="4">Карта 46</td><td colspan="3">лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Характер обработки</td><td rowspan="3">Ширина обрабатываемой поверхности, В, мм, до</td><td rowspan="2">Число рабочих</td><td colspan="8">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td colspan="2">100</td><td>200</td><td>300</td><td colspan="2">400</td><td>500</td><td>600</td></tr>
<tr><td>ходов</td><td colspan="8">Время на поверхность, t , мин. нш</td></tr>
<tr><td>21</td><td>Стро-</td><td>Rz 80;</td><td>10</td><td>1</td><td colspan="2">1,8</td><td>2,0</td><td>2,2</td><td colspan="2">2,4</td><td>2,5</td><td>2,6</td></tr>
<tr><td>22</td><td>гание</td><td>14...</td><td>25</td><td></td><td colspan="2">2,0</td><td>2,4</td><td>2,6</td><td colspan="2">3,0</td><td>3,3</td><td>3,5</td></tr>
<tr><td>23</td><td>гори-</td><td>12</td><td>40</td><td></td><td colspan="2">2,3</td><td>2,7</td><td>3,2</td><td colspan="2">3,5</td><td>3,8</td><td>4,4</td></tr>
<tr><td>24</td><td>зонта-</td><td>ква-</td><td>50</td><td></td><td colspan="2">2,6</td><td>3,0</td><td>3,5</td><td colspan="2">4,0</td><td>4,4</td><td>5,0</td></tr>
<tr><td>25</td><td>льных</td><td>литет</td><td>60</td><td></td><td colspan="2">2,9</td><td>3,3</td><td>3,8</td><td colspan="2">4,6</td><td>5,0</td><td>5,6</td></tr>
<tr><td>26</td><td>повер-</td><td></td><td>80</td><td></td><td colspan="2">3,2</td><td>3,7</td><td>4,6</td><td colspan="2">5,4</td><td>6,0</td><td>6,9</td></tr>
<tr><td>27</td><td rowspan="2">хностей</td><td></td><td>100</td><td></td><td colspan="2">3,8</td><td>4,2</td><td>5,2</td><td colspan="2">6,3</td><td>6,4</td><td>8,0</td></tr>
<tr><td>28</td><td>Rz 40,</td><td>10</td><td>2</td><td colspan="2">4,5</td><td>4,8</td><td>5,4</td><td colspan="2">5,6</td><td>5,8</td><td>6,3</td></tr>
<tr><td>29</td><td></td><td>Rz 20;</td><td>25</td><td></td><td colspan="2">5,4</td><td>6,0</td><td>6,9</td><td colspan="2">7,6</td><td>8,5</td><td>9,0</td></tr>
<tr><td>30</td><td></td><td>11</td><td>40</td><td></td><td colspan="2">6,3</td><td>7,0</td><td>8,4</td><td colspan="2">9,5</td><td>11</td><td>12</td></tr>
<tr><td>31</td><td></td><td>ква-</td><td>50</td><td></td><td colspan="2">7,0</td><td>7,9</td><td>9,5</td><td colspan="2">11</td><td>13</td><td>14</td></tr>
<tr><td>32</td><td></td><td>литет</td><td>60</td><td></td><td colspan="2">8,0</td><td>8,6</td><td>11</td><td colspan="2">13</td><td>14</td><td>16</td></tr>
<tr><td>33</td><td></td><td></td><td>80</td><td></td><td colspan="2">8,9</td><td>10</td><td>13</td><td colspan="2">16</td><td>18</td><td>20</td></tr>
<tr><td>34</td><td></td><td></td><td>100</td><td></td><td colspan="2">9,5</td><td>12</td><td>14</td><td colspan="2">18</td><td>20</td><td>24</td></tr>
<tr><td colspan="5">Индекс</td><td colspan="2">а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td></tr>
</table>



<a id="p101525"></a>

<table>
<colgroup><col width="6%"><col width="22%"><col width="25%"><col width="12%"><col width="6%"><col width="5%"><col width="3%"><col width="8%"><col width="14%"></colgroup>
<tr><td colspan="3">Неполное штучное время Строгание поверхностей</td><td colspan="6">Поперечно-строгальные станки</td></tr>
<tr><td colspan="3" rowspan="2">Чугун серый, НВ = 1760...2150 МПа</td><td colspan="6">Резцы проходные с пластинками ВК8, ВК6</td></tr>
<tr><td colspan="4">Карта 46</td><td colspan="2">лист 3</td></tr>
<tr><td colspan="9">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="2">1.</td><td rowspan="2">Обрабатываемого материала</td><td>Материал</td><td colspan="3">Чугун серый</td><td colspan="2">Бронза Латунь</td><td>Баббит Алюминий</td></tr>
<tr><td>Твердость, НВ, МПа Коэффициент К пп</td><td>до 2150 1,0</td><td colspan="2">св. 2150 1,2</td><td colspan="2">0,8</td><td>0,7</td></tr>
<tr><td>2.</td><td>Мощности привода станка</td><td>Мощность, кВт Коэффициент К N</td><td colspan="2">3,0 1,2</td><td colspan="3">5,0 1,1</td><td>8 - 10 1,0</td></tr>
<tr><td>3.</td><td>Угла в плане резца</td><td>фи, град. Коэффициент К фи</td><td colspan="4">45...60 1,0</td><td colspan="2">90 1,2</td></tr>
<tr><td rowspan="2">4.</td><td rowspan="2">Формы обрабатываемой поверхности</td><td>Поверхность</td><td colspan="4">прямолинейная</td><td colspan="2">криволинейная</td></tr>
<tr><td>Коэффициент К ф</td><td colspan="4">1,6</td><td colspan="2">1,2</td></tr>
<tr><td>5.</td><td>Отношения скорости рабочего хода к холостому</td><td>Отношение скорости рабочего хода к холостому Коэффициент К m</td><td colspan="2">0,8 1,0</td><td colspan="4">0,70 0,6 0,9 0,8</td></tr>
</table>


<a id="p101527"></a>Примечания:
1. <a id="p101528"></a>При строгании одновременно нескольких заготовок ширина обрабатываемой поверхности (или длина) и, соответственно, время на обработку определяются с учетом количества деталей, устанавливаемых на станке.
2. <a id="p101529"></a>При строгании наклонных плоскостей (типа "Ласточкин хвост") к времени по карте для вертикальных плоскостей следует добавлять время на поворот суппорта на угол и на измерения в размере 4 - 5 мин.


<table>
<colgroup><col width="4%"><col width="6%"><col width="6%"><col width="7%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="24">Неполное штучное время Поперечно-строгальные станки Строгание прямоугольных пазов, Rz 80; 14...12 квалитет</td></tr>
<tr><td colspan="24">Чугун серый, НВ = 1760...2150 МПа Резцы с пластинками из стали Р6М5, ВК8</td></tr>
<tr><td colspan="24">Карта 47</td></tr>
<tr><td colspan="24">рисунок не приводится</td></tr>
<tr><td rowspan="4">N позиции</td><td>Ширина</td><td>Глубина</td><td rowspan="4">Число проходов, i</td><td colspan="20">Резцы с пластинками ВК8 Резцы из стали Р6М5</td></tr>
<tr><td>паза, В,</td><td>паза, Н,</td><td colspan="20">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">мм, до</td><td rowspan="2">мм, до</td><td>50</td><td colspan="2">100</td><td>200</td><td>300</td><td>400</td><td>500</td><td colspan="2">600</td><td>700</td><td>800</td><td>50</td><td>100</td><td>200</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td></tr>
<tr><td colspan="20">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>10</td><td>5</td><td>1</td><td>1,6</td><td colspan="2">1,9</td><td>2,3</td><td>2,5</td><td>2,7</td><td>3,4</td><td colspan="2">3,8</td><td>4,3</td><td>4,6</td><td>1,8</td><td>2,3</td><td>2,7</td><td>3,0</td><td>3,6</td><td>4,3</td><td>4,8</td><td>5,4</td><td>6,2</td></tr>
<tr><td>2</td><td></td><td>12</td><td></td><td>2,3</td><td colspan="2">2,7</td><td>3,0</td><td>3,3</td><td>4,0</td><td>4,6</td><td colspan="2">5,2</td><td>5,5</td><td>6,3</td><td>2,7</td><td>3,2</td><td>3,8</td><td>4,2</td><td>5,3</td><td>6,2</td><td>6,9</td><td>7,9</td><td>8,8</td></tr>
<tr><td>3</td><td></td><td>20</td><td rowspan="2"></td><td>2,7</td><td colspan="2">3,2</td><td>3,9</td><td>4,3</td><td>5,4</td><td>6,4</td><td colspan="2">7,2</td><td>7,7</td><td>8,7</td><td>3,6</td><td>4,2</td><td>5,0</td><td>5,5</td><td>7,3</td><td>8,6</td><td>10</td><td>11</td><td>12</td></tr>
<tr><td>4</td><td>15</td><td>10</td><td>1,8</td><td colspan="2">2,3</td><td>2,5</td><td>2,8</td><td>3,4</td><td>4,2</td><td colspan="2">4,5</td><td>5,0</td><td>5,6</td><td>2,0</td><td>2,5</td><td>3,2</td><td>3,6</td><td>4,5</td><td>5,4</td><td>6,2</td><td>7,0</td><td>7,9</td></tr>
<tr><td>5</td><td></td><td>20</td><td></td><td>2,7</td><td colspan="2">3,2</td><td>3,8</td><td>4,2</td><td>5,0</td><td>5,9</td><td colspan="2">6,9</td><td>7,3</td><td>8,6</td><td>3,6</td><td>4,2</td><td>5,0</td><td>5,5</td><td>7,3</td><td>8,6</td><td>10</td><td>11</td><td>12</td></tr>
<tr><td>6</td><td></td><td>30</td><td></td><td>3,3</td><td colspan="2">3,8</td><td>4,6</td><td>5,3</td><td>6,6</td><td>7,8</td><td colspan="2">9,0</td><td>10</td><td>11</td><td>4,5</td><td>5,4</td><td>6,3</td><td>7,4</td><td>10</td><td>11</td><td>14</td><td>15</td><td>19</td></tr>
<tr><td>7</td><td>25</td><td>30</td><td>2</td><td>4,0</td><td colspan="2">5,0</td><td>6,7</td><td>8,0</td><td>10</td><td>12</td><td colspan="2">14</td><td>18</td><td>20</td><td>7,3</td><td>8,5</td><td>10</td><td>12</td><td>15</td><td>19</td><td>23</td><td>27</td><td>31</td></tr>
<tr><td>8</td><td></td><td>40</td><td rowspan="2"></td><td>5,0</td><td colspan="2">5,8</td><td>7,7</td><td>10</td><td>13</td><td>15</td><td colspan="2">18</td><td>22</td><td>26</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>20</td><td>25</td><td>29</td><td>34</td><td>40</td></tr>
<tr><td>9</td><td>30</td><td>40</td><td>5,0</td><td colspan="2">5,8</td><td>7,7</td><td>10</td><td>13</td><td>15</td><td colspan="2">18</td><td>22</td><td>26</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>20</td><td>25</td><td>29</td><td>34</td><td>40</td></tr>
<tr><td>10</td><td></td><td>50</td><td></td><td>5,9</td><td colspan="2">6,9</td><td>9,5</td><td>12</td><td>15</td><td>19</td><td colspan="2">22</td><td>26</td><td>31</td><td>10</td><td>12</td><td>15</td><td>18</td><td>25</td><td>29</td><td>35</td><td>43</td><td>50</td></tr>
<tr><td>11</td><td>35</td><td>50</td><td>3</td><td>5,0</td><td colspan="2">7,0</td><td>9,5</td><td>12</td><td>15</td><td>19</td><td colspan="2">22</td><td>26</td><td>31</td><td>10</td><td>12</td><td>14</td><td>18</td><td>25</td><td>29</td><td>35</td><td>43</td><td>50</td></tr>
<tr><td>12</td><td></td><td>70</td><td rowspan="2"></td><td>8,6</td><td colspan="2">10</td><td>13</td><td>16</td><td>21</td><td>26</td><td colspan="2">31</td><td>35</td><td>42</td><td>14</td><td>16</td><td>20</td><td>24</td><td>33</td><td>42</td><td>48</td><td>56</td><td>66</td></tr>
<tr><td>13</td><td>50</td><td>50</td><td>9,0</td><td colspan="2">11</td><td>14</td><td>16</td><td>23</td><td>27</td><td colspan="2">32</td><td>40</td><td>46</td><td>14</td><td>17</td><td>22</td><td>26</td><td>35</td><td>43</td><td>52</td><td>64</td><td>74</td></tr>
<tr><td>14</td><td></td><td>70</td><td></td><td>11</td><td colspan="2">14</td><td>17</td><td>23</td><td>31</td><td>32</td><td colspan="2">45</td><td>53</td><td>62</td><td>19</td><td>23</td><td>30</td><td>36</td><td>48</td><td>60</td><td>72</td><td>85</td><td>100</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td></tr>
<tr><td colspan="24">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6" rowspan="2">1. Обрабатываемого материала</td><td colspan="6">Материал</td><td colspan="6">Чугун серый</td><td colspan="6">Бронза, Баббит, латунь алюминий</td></tr>
<tr><td colspan="6">Твердость, НВ, МПа Коэффициент К тв</td><td colspan="3">до 2150 1,0</td><td colspan="3">св. 2150 1,2</td><td colspan="6">0,8 0,7</td></tr>
<tr><td colspan="6">2. Отношения скорости рабочего хода к холостому</td><td colspan="9">Отношение скорости рабочего хода к холостому Коэффициент К m</td><td colspan="3">0,8 1,0</td><td colspan="6">0,70 0,6 0,90 0,8</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="9%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="19">Неполное штучное время Поперечно-строгальные станки Строгание плоскостей</td></tr>
<tr><td colspan="19">Сталь конструкционная, сигма = 590...740 МПа Резцы из стали Р6М5 в</td></tr>
<tr><td colspan="15">Карта 48</td><td colspan="4">лист 1</td></tr>
<tr><td colspan="19">рисунок не приводится</td></tr>
<tr><td rowspan="4">N позиции</td><td rowspan="4">Характер обработки</td><td rowspan="2">Ширина обрабатываемой</td><td colspan="8">Заготовка из проката</td><td colspan="8">Поковка или отливка</td></tr>
<tr><td colspan="16">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>поверхности,</td><td>100</td><td>200</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>100</td><td>200</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td></tr>
<tr><td>В, мм, до</td><td colspan="16">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Строгание</td><td>25</td><td>2,4</td><td>2,7</td><td>3,0</td><td>3,3</td><td>3,5</td><td>4,0</td><td>4,2</td><td>4,6</td><td>5,0</td><td>5,6</td><td>6,4</td><td>7,0</td><td>7,5</td><td>8,3</td><td>8,8</td><td>9,0</td></tr>
<tr><td>2</td><td>горизон-</td><td>50</td><td>3,0</td><td>3,5</td><td>4,4</td><td>5,0</td><td>5,6</td><td>6,3</td><td>7,0</td><td>7,5</td><td>6,0</td><td>7,5</td><td>9,0</td><td>11</td><td>12</td><td>13</td><td>15</td><td>16</td></tr>
<tr><td>3</td><td>тальных</td><td>75</td><td>3,3</td><td>4,4</td><td>5,6</td><td>6,7</td><td>7,6</td><td>8,6</td><td>9,5</td><td>11</td><td>7,0</td><td>9,0</td><td>12</td><td>14</td><td>16</td><td>18</td><td>20</td><td>23</td></tr>
<tr><td>4</td><td>поверх-</td><td>100</td><td>3,8</td><td>5,4</td><td>7,0</td><td>8,4</td><td>9,5</td><td>11</td><td>12</td><td>13</td><td>8,0</td><td>11</td><td>14</td><td>17</td><td>20</td><td>23</td><td>26</td><td>29</td></tr>
<tr><td>5</td><td>ностей</td><td>150</td><td>4,7</td><td>7,0</td><td>9,0</td><td>11</td><td>13</td><td>15</td><td>16</td><td>18</td><td>10</td><td>15</td><td>19</td><td>23</td><td>27</td><td>31</td><td>34</td><td>39</td></tr>
<tr><td>6</td><td>Rz 80;</td><td>200</td><td>5,6</td><td>8,6</td><td>12</td><td>15</td><td>17</td><td>20</td><td>22</td><td>24</td><td>12</td><td>18</td><td>24</td><td>31</td><td>36</td><td>41</td><td>47</td><td>52</td></tr>
<tr><td>7</td><td>14...12</td><td>250</td><td>6,6</td><td>10,4</td><td>14</td><td>18</td><td>21</td><td>24</td><td>28</td><td>31</td><td>14</td><td>22</td><td>29</td><td>37</td><td>44</td><td>51</td><td>58</td><td>64</td></tr>
<tr><td>8</td><td>квалитет</td><td>300</td><td>7,7</td><td>12</td><td>16</td><td>22</td><td>25</td><td>29</td><td>33</td><td>37</td><td>16</td><td>25</td><td>34</td><td>46</td><td>53</td><td>61</td><td>69</td><td>77</td></tr>
<tr><td>9</td><td></td><td>350</td><td>8,6</td><td>14</td><td>19</td><td>24</td><td>29</td><td>34</td><td>39</td><td>44</td><td>18</td><td>29</td><td>41</td><td>52</td><td>61</td><td>73</td><td>83</td><td>92</td></tr>
<tr><td>10</td><td></td><td>400</td><td>9,5</td><td>16</td><td>22</td><td>28</td><td>33</td><td>39</td><td>45</td><td>50</td><td>20</td><td>33</td><td>46</td><td>58</td><td>69</td><td>83</td><td>94</td><td>104</td></tr>
<tr><td colspan="3">Число проходов</td><td colspan="8">1</td><td colspan="8">2</td></tr>
<tr><td>11</td><td>Строгание</td><td>25</td><td>5,5</td><td>6,0</td><td>7,5</td><td>8,0</td><td>8,4</td><td>9,0</td><td>9,5</td><td>11</td><td>8,0</td><td>9,0</td><td>11</td><td>12</td><td>13</td><td>14</td><td>15</td><td>16</td></tr>
<tr><td>12</td><td>горизон-</td><td>50</td><td>6,3</td><td>7,4</td><td>9,5</td><td>11</td><td>12</td><td>13</td><td>16</td><td>18</td><td>9,5</td><td>11</td><td>15</td><td>16</td><td>18</td><td>20</td><td>24</td><td>26</td></tr>
<tr><td>13</td><td>тальных</td><td>75</td><td>7,5</td><td>9,0</td><td>13</td><td>15</td><td>16</td><td>18</td><td>23</td><td>24</td><td>11</td><td>14</td><td>18</td><td>22</td><td>24</td><td>28</td><td>33</td><td>35</td></tr>
<tr><td>14</td><td>поверх-</td><td>100</td><td>8,5</td><td>11</td><td>16</td><td>18</td><td>20</td><td>24</td><td>28</td><td>32</td><td>13</td><td>17</td><td>24</td><td>28</td><td>31</td><td>35</td><td>42</td><td>47</td></tr>
<tr><td>15</td><td>ностей</td><td>150</td><td>10,5</td><td>14</td><td>21</td><td>25</td><td>27</td><td>32</td><td>38</td><td>44</td><td>16</td><td>22</td><td>31</td><td>37</td><td>41</td><td>48</td><td>56</td><td>63</td></tr>
<tr><td>16</td><td>Rz 40,</td><td>200</td><td>13</td><td>18</td><td>27</td><td>32</td><td>35</td><td>42</td><td>52</td><td>56</td><td>19</td><td>28</td><td>39</td><td>48</td><td>54</td><td>63</td><td>76</td><td>83</td></tr>
<tr><td>17</td><td>Rz 20;</td><td>250</td><td>14</td><td>22</td><td>33</td><td>39</td><td>44</td><td>52</td><td>63</td><td>71</td><td>21</td><td>33</td><td>48</td><td>58</td><td>67</td><td>79</td><td>94</td><td>104</td></tr>
<tr><td>18</td><td>11</td><td>300</td><td>18</td><td>27</td><td>39</td><td>47</td><td>54</td><td>63</td><td>76</td><td>85</td><td>27</td><td>39</td><td>58</td><td>71</td><td>81</td><td>94</td><td>112</td><td>126</td></tr>
<tr><td>19</td><td>квалитет</td><td>350</td><td>20</td><td>29</td><td>46</td><td>54</td><td>63</td><td>73</td><td>89</td><td>99</td><td>29</td><td>44</td><td>66</td><td>81</td><td>94</td><td>109</td><td>132</td><td>147</td></tr>
<tr><td>20</td><td></td><td>400</td><td>22</td><td>33</td><td>52</td><td>63</td><td>71</td><td>83</td><td>102</td><td>114</td><td>33</td><td>51</td><td>76</td><td>93</td><td>107</td><td>127</td><td>151</td><td>163</td></tr>
<tr><td colspan="3">Число проходов</td><td colspan="8">2</td><td colspan="8">3</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="13%"><col width="6%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="3%"><col width="2%"><col width="6%"><col width="6%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="5%"><col width="2%"><col width="7%"></colgroup>
<tr><td colspan="12">Неполное штучное время Строгание плоскостей</td><td colspan="10">Поперечно-строгальные станки</td></tr>
<tr><td colspan="12" rowspan="2">Сталь конструкционная, сигма = 590...740 МПа в</td><td colspan="10">Резцы из стали Р6М5</td></tr>
<tr><td colspan="10">Карта 48 лист 2</td></tr>
<tr><td colspan="2">N Характер по- обработки</td><td colspan="2" rowspan="2">Ширина обрабатываемой</td><td colspan="7">Заготовка из проката</td><td colspan="11">Поковка или отливка</td></tr>
<tr><td colspan="2" rowspan="3">зиции</td><td colspan="18">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td colspan="2">поверхности,</td><td>100</td><td>200</td><td>300</td><td colspan="2">400</td><td>500</td><td>600</td><td colspan="2">100</td><td colspan="2">200</td><td colspan="2">300</td><td colspan="2">400</td><td colspan="2">500</td><td>600</td></tr>
<tr><td colspan="2">В, мм, до</td><td colspan="18">Время на поверхность, t , мин. нш</td></tr>
<tr><td colspan="2">21 Строгание</td><td colspan="2">10</td><td>2,0</td><td>2,7</td><td>3,0</td><td colspan="2">3,4</td><td>3,8</td><td>4,2</td><td colspan="2">4,0</td><td colspan="2">5,6</td><td colspan="2">6,3</td><td colspan="2">7,0</td><td colspan="2">8,0</td><td>8,8</td></tr>
<tr><td colspan="2">22 верти-</td><td colspan="2">25</td><td>3,0</td><td>3,8</td><td>4,6</td><td colspan="2">5,6</td><td>6,3</td><td>7,0</td><td colspan="2">6,0</td><td colspan="2">8,0</td><td colspan="2">9,5</td><td colspan="2">12</td><td colspan="2">13</td><td>15</td></tr>
<tr><td colspan="2">23 кальных</td><td colspan="2">40</td><td>3,5</td><td>5,0</td><td>6,5</td><td colspan="2">7,6</td><td>9,0</td><td>10</td><td colspan="2">7,5</td><td colspan="2">10,5</td><td colspan="2">13</td><td colspan="2">16</td><td colspan="2">18</td><td>21</td></tr>
<tr><td colspan="2">24 поверх-</td><td colspan="2">50</td><td>4,0</td><td>5,6</td><td>7,5</td><td colspan="2">9,0</td><td>11</td><td>12</td><td colspan="2">8,5</td><td colspan="2">12</td><td colspan="2">16</td><td colspan="2">19</td><td colspan="2">22</td><td>25</td></tr>
<tr><td colspan="2">25 ностей</td><td colspan="2">60</td><td>4,5</td><td>6,4</td><td>8,5</td><td colspan="2">11</td><td>13</td><td>14</td><td colspan="2">9,0</td><td colspan="2">13</td><td colspan="2">18</td><td colspan="2">22</td><td colspan="2">25</td><td>29</td></tr>
<tr><td colspan="2">26 Rz 80;</td><td colspan="2">80</td><td>5,0</td><td>8,0</td><td>11</td><td colspan="2">13</td><td>16</td><td>18</td><td colspan="2">11</td><td colspan="2">16</td><td colspan="2">22</td><td colspan="2">28</td><td colspan="2">33</td><td>37</td></tr>
<tr><td colspan="2">27 14...12 квалитет</td><td colspan="2">100</td><td>6,0</td><td>9,0</td><td>13</td><td colspan="2">16</td><td>19</td><td>22</td><td colspan="2">13</td><td colspan="2">19</td><td colspan="2">27</td><td colspan="2">34</td><td colspan="2">41</td><td>46</td></tr>
<tr><td colspan="4">Число проходов</td><td colspan="7">1</td><td colspan="11">2</td></tr>
<tr><td colspan="2">28 Строгание</td><td colspan="2">10</td><td>5,5</td><td>7,0</td><td>8,0</td><td colspan="2">9,5</td><td>11</td><td>12</td><td colspan="2">8,0</td><td colspan="2">10</td><td colspan="2">11</td><td colspan="2">13</td><td colspan="2">14,5</td><td>16</td></tr>
<tr><td colspan="2">29 верти-</td><td colspan="2">25</td><td>8,0</td><td>11</td><td>14</td><td colspan="2">17</td><td>20</td><td>22</td><td colspan="2">11</td><td colspan="2">16</td><td colspan="2">19</td><td colspan="2">23</td><td colspan="2">27</td><td>31</td></tr>
<tr><td colspan="2">30 кальных</td><td colspan="2">40</td><td>10</td><td>15</td><td>20</td><td colspan="2">25</td><td>28</td><td>33</td><td colspan="2">14</td><td colspan="2">20</td><td colspan="2">27</td><td colspan="2">33</td><td colspan="2">38</td><td>44</td></tr>
<tr><td colspan="2">31 поверх-</td><td colspan="2">50</td><td>11</td><td>16</td><td>24</td><td colspan="2">29</td><td>34</td><td>39</td><td colspan="2">16</td><td colspan="2">22</td><td colspan="2">32</td><td colspan="2">39</td><td colspan="2">46</td><td>54</td></tr>
<tr><td colspan="2">32 ностей</td><td colspan="2">60</td><td>13</td><td>20</td><td>28</td><td colspan="2">34</td><td>41</td><td>47</td><td colspan="2">18</td><td colspan="2">27</td><td colspan="2">37</td><td colspan="2">46</td><td colspan="2">54</td><td>63</td></tr>
<tr><td colspan="2">33 Rz 40,</td><td colspan="2">80</td><td>16</td><td>25</td><td>34</td><td colspan="2">44</td><td>54</td><td>63</td><td colspan="2">22</td><td colspan="2">34</td><td colspan="2">46</td><td colspan="2">60</td><td colspan="2">71</td><td>81</td></tr>
<tr><td colspan="2">34 Rz 20; 11 квалитет</td><td colspan="2">100</td><td>18</td><td>31</td><td>43</td><td colspan="2">56</td><td>66</td><td>76</td><td colspan="2">25</td><td colspan="2">41</td><td colspan="2">57</td><td colspan="2">73</td><td colspan="2">86</td><td>101</td></tr>
<tr><td colspan="4">Число проходов</td><td colspan="7">2</td><td colspan="11">3</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td colspan="2">ж</td><td colspan="2">з</td><td colspan="2">и</td><td colspan="2">к</td><td colspan="2">л</td><td>м</td></tr>
<tr><td colspan="22">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="2">1.</td><td colspan="2" rowspan="2">Обрабатываемого материала</td><td colspan="5">Группа стали</td><td colspan="12">Углеродистые конструкционные Коррозион-</td><td colspan="2" rowspan="2">Жаропрочные прочные 1,45</td></tr>
<tr><td colspan="5">Предел прочности, сигма , МПа в Коэффициент К пп</td><td colspan="5">до 590 590...740 0,9 1,0</td><td colspan="7">св. 740 ностойкие 1,2 1,35</td></tr>
<tr><td>2.</td><td colspan="2">Мощности привода</td><td colspan="5">Мощность, N, кВт Коэффициент К N</td><td colspan="6">3 1,2</td><td colspan="8">5 8...10 1,1 1,0</td></tr>
<tr><td>3.</td><td colspan="2">Формы обрабатываемой поверхности</td><td colspan="5">Поверхность Коэффициент К ф</td><td colspan="14">Прямолинейная Криволинейная (фасонная) 1,0 1,2</td></tr>
<tr><td>4.</td><td colspan="2">Угла в плане резца</td><td colspan="5">фи, град. Коэффициент К фи</td><td colspan="8">45...60° 1,0</td><td colspan="6">90° 1,4</td></tr>
<tr><td>5.</td><td colspan="2">Материала режущего инструмента</td><td colspan="5">Материал инструмента Коэффициент К ри</td><td colspan="8">Быстрорежущая сталь 1,0</td><td colspan="6">Твердый сплав 0,6</td></tr>
<tr><td>6.</td><td colspan="2">Отношения скорости рабочего хода к холостому</td><td colspan="15">Отношение скорости рабочего хода к холостому 0,8 Коэффициент К 1,0 m</td><td colspan="2">0,70 0,90</td><td colspan="2">0,6 0,8</td></tr>
</table>


<a id="p101608"></a>*Примечание.* При строгании наклонных плоскостей (типа "Ласточкин хвост") к времени по карте следует добавлять время на поворот суппорта на угол и на измерения в размере 4 - 5 мин.


<table>
<colgroup><col width="6%"><col width="11%"><col width="8%"><col width="5%"><col width="15%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="3%"><col width="3%"><col width="6%"></colgroup>
<tr><td colspan="15">Неполное штучное время Поперечно-строгальные станки Строгание прямоугольных пазов, Rz 80; 14...12 квалитет Резцы из стали Р6М5 Сталь конструкционная, сигма = 590...740 МПа Карта 49 в</td></tr>
<tr><td colspan="15">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина паза, В, мм,</td><td colspan="2">Глубина паза, Н, мм,</td><td rowspan="3">Число проходов, i</td><td colspan="10">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">до</td><td colspan="2" rowspan="2">до</td><td>50</td><td>100</td><td>200</td><td>300</td><td>400</td><td>500</td><td>600</td><td colspan="2">700</td><td>800</td></tr>
<tr><td colspan="10">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>10</td><td colspan="2">5</td><td>1</td><td>2,0</td><td>2,7</td><td>3,4</td><td>4,0</td><td>4,8</td><td>6,0</td><td>6,7</td><td colspan="2">7,4</td><td>8,6</td></tr>
<tr><td>2</td><td></td><td colspan="2">12</td><td></td><td>3,6</td><td>4,5</td><td>5,4</td><td>6,4</td><td>8,3</td><td>11</td><td>12</td><td colspan="2">13</td><td>16</td></tr>
<tr><td>3</td><td></td><td colspan="2">20</td><td></td><td>5,5</td><td>6,7</td><td>7,7</td><td>9,0</td><td>13</td><td>16</td><td>18</td><td colspan="2">19</td><td>23</td></tr>
<tr><td>4</td><td>15</td><td colspan="2">10</td><td>1</td><td>2,7</td><td>4,2</td><td>5,0</td><td>6,0</td><td>7,5</td><td>9,0</td><td>11</td><td colspan="2">12</td><td>13</td></tr>
<tr><td>5</td><td></td><td colspan="2">20</td><td></td><td>5,5</td><td>6,7</td><td>8,0</td><td>9,5</td><td>13</td><td>16</td><td>19</td><td colspan="2">20</td><td>23</td></tr>
<tr><td>6</td><td></td><td colspan="2">30</td><td></td><td>6,8</td><td>9,0</td><td>11</td><td>13</td><td>17</td><td>21</td><td>27</td><td colspan="2">28</td><td>33</td></tr>
<tr><td>7</td><td>25</td><td colspan="2">30</td><td>2</td><td>8,0</td><td>10</td><td>15</td><td>21</td><td>28</td><td>35</td><td>39</td><td colspan="2">50</td><td>56</td></tr>
<tr><td>8</td><td></td><td colspan="2">40</td><td></td><td>16</td><td>18</td><td>23</td><td>27</td><td>36</td><td>46</td><td>50</td><td colspan="2">63</td><td>73</td></tr>
<tr><td>9</td><td>30</td><td colspan="2">40</td><td>2</td><td>16</td><td>20</td><td>23</td><td>27</td><td>36</td><td>46</td><td>50</td><td colspan="2">63</td><td>73</td></tr>
<tr><td>10</td><td></td><td colspan="2">50</td><td></td><td>17</td><td>20</td><td>27</td><td>33</td><td>44</td><td>55</td><td>62</td><td colspan="2">78</td><td>89</td></tr>
<tr><td>11</td><td>35</td><td colspan="2">50</td><td>2</td><td>17</td><td>20</td><td>27</td><td>33</td><td>44</td><td>55</td><td>62</td><td colspan="2">78</td><td>89</td></tr>
<tr><td>12</td><td></td><td colspan="2">70</td><td></td><td>23</td><td>27</td><td>38</td><td>44</td><td>63</td><td>78</td><td>85</td><td colspan="2">104</td><td>123</td></tr>
<tr><td>13</td><td>50</td><td colspan="2">50</td><td>3</td><td>25</td><td>29</td><td>39</td><td>48</td><td>66</td><td>83</td><td>91</td><td colspan="2">118</td><td>136</td></tr>
<tr><td>14</td><td></td><td colspan="2">70</td><td></td><td>36</td><td>42</td><td>56</td><td>67</td><td>94</td><td>109</td><td>123</td><td colspan="2">159</td><td>186</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td></tr>
<tr><td colspan="15">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3" rowspan="2">1. Обрабатываемого материала</td><td colspan="10">Группа стали Углеродистые Коррозиконструкционные оннос- Предел прочности, тойкие</td><td colspan="2">Жаропрочные</td></tr>
<tr><td colspan="6">сигма , МПа до 590... в 590 740 Коэффициент К 0,9 1,0 пп</td><td colspan="4">св. 740 1,2 1,35</td><td colspan="2">1,45</td></tr>
<tr><td colspan="3">2. Мощности привода станка</td><td colspan="12">Мощность, N, кВт 3 5 8...10 Коэффициент К 1,2 1,1 1,0 N</td></tr>
<tr><td colspan="3">3. Отношения скорости рабочего хода к холостому</td><td colspan="12">Отношение скорос- 0,8 0,70 0,6 ти рабочего хода к холостому, до Коэффициент К 1,0 0,90 0,8 m</td></tr>
</table>



###### <a id="p101634"></a>4.2.3. Долбежные станки



<table>
<colgroup><col width="6%"><col width="15%"><col width="15%"><col width="11%"><col width="6%"><col width="8%"><col width="3%"><col width="5%"><col width="6%"><col width="3%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="8">Неполное штучное время Обработка плоскостей</td><td colspan="6">Долбежные станки</td></tr>
<tr><td colspan="8" rowspan="2">Чугун серый, НВ = 1760...2150 МПа</td><td colspan="6">Резцы из стали Р6М5</td></tr>
<tr><td colspan="6">Карта 50</td></tr>
<tr><td colspan="14">рисунок не приводится</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Шероховатость и точность</td><td>Ширина обрабатываемой</td><td rowspan="3">Число проходов, i</td><td colspan="10">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td>поверхности, В,</td><td>50</td><td>100</td><td colspan="2">150</td><td>200</td><td colspan="2">250</td><td>300</td><td>400</td><td>500</td></tr>
<tr><td>мм, до</td><td colspan="10">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>25</td><td>1</td><td>2,2</td><td>2,7</td><td colspan="2">3,3</td><td>3,8</td><td colspan="2">4,3</td><td>4,6</td><td>5,5</td><td>6,3</td></tr>
<tr><td>2</td><td>14...12</td><td>50</td><td></td><td>3,0</td><td>3,7</td><td colspan="2">4,6</td><td>5,2</td><td colspan="2">6,0</td><td>6,7</td><td>8,3</td><td>9,6</td></tr>
<tr><td>3</td><td>квалитет</td><td>75</td><td></td><td>3,4</td><td>4,8</td><td colspan="2">6,0</td><td>7,0</td><td colspan="2">8,1</td><td>9,3</td><td>11</td><td>13</td></tr>
<tr><td>4</td><td></td><td>100</td><td></td><td>4,6</td><td>5,8</td><td colspan="2">7,4</td><td>8,6</td><td colspan="2">10</td><td>11</td><td>14</td><td>17</td></tr>
<tr><td>5</td><td></td><td>150</td><td></td><td>6,3</td><td>8,2</td><td colspan="2">10</td><td>12</td><td colspan="2">14</td><td>16</td><td>20</td><td>24</td></tr>
<tr><td>6</td><td></td><td>200</td><td></td><td>7,7</td><td>10</td><td colspan="2">13</td><td>15</td><td colspan="2">18</td><td>21</td><td>26</td><td>31</td></tr>
<tr><td>7</td><td></td><td>250</td><td></td><td>9,3</td><td>12</td><td colspan="2">16</td><td>19</td><td colspan="2">22</td><td>25</td><td>32</td><td>38</td></tr>
<tr><td>8</td><td></td><td>300</td><td></td><td>11</td><td>14</td><td colspan="2">19</td><td>22</td><td colspan="2">26</td><td>30</td><td>38</td><td>45</td></tr>
<tr><td>9</td><td></td><td>400</td><td></td><td>14</td><td>18,4</td><td colspan="2">24,5</td><td>29</td><td colspan="2">34</td><td>39</td><td>50</td><td>59</td></tr>
<tr><td>10</td><td></td><td>500</td><td></td><td>17</td><td>23</td><td colspan="2">30</td><td>36</td><td colspan="2">42</td><td>49</td><td>62</td><td>73</td></tr>
<tr><td>11</td><td>Rz 40...</td><td>25</td><td>2</td><td>5,0</td><td>6,1</td><td colspan="2">7,5</td><td>8,6</td><td colspan="2">9,8</td><td>10</td><td>12</td><td>14</td></tr>
<tr><td>12</td><td>Rz 20;</td><td>50</td><td></td><td>6,8</td><td>8,4</td><td colspan="2">10</td><td>12</td><td colspan="2">14</td><td>15</td><td>19</td><td>22</td></tr>
<tr><td>13</td><td>точность</td><td>75</td><td></td><td>7,7</td><td>11</td><td colspan="2">14</td><td>16</td><td colspan="2">18</td><td>21</td><td>25</td><td>30</td></tr>
<tr><td>14</td><td>измерения</td><td>100</td><td></td><td>10</td><td>13</td><td colspan="2">17</td><td>20</td><td colspan="2">23</td><td>25</td><td>32</td><td>38</td></tr>
<tr><td>15</td><td>0,3...0,5</td><td>150</td><td></td><td>14</td><td>18</td><td colspan="2">24</td><td>28</td><td colspan="2">32</td><td>36</td><td>45</td><td>54</td></tr>
<tr><td>16</td><td></td><td>200</td><td></td><td>17</td><td>23</td><td colspan="2">29</td><td>34</td><td colspan="2">41</td><td>47</td><td>59</td><td>79</td></tr>
<tr><td>17</td><td></td><td>250</td><td></td><td>21</td><td>27</td><td colspan="2">36</td><td>43</td><td colspan="2">50</td><td>57</td><td>73</td><td>86</td></tr>
<tr><td>18</td><td></td><td>300</td><td></td><td>25</td><td>32</td><td colspan="2">43</td><td>50</td><td colspan="2">59</td><td>68</td><td>86</td><td>102</td></tr>
<tr><td>19</td><td></td><td>400</td><td></td><td>32</td><td>42</td><td colspan="2">56</td><td>66</td><td colspan="2">77</td><td>88</td><td>113</td><td>134</td></tr>
<tr><td>20</td><td></td><td>500</td><td></td><td>38</td><td>52</td><td colspan="2">68</td><td>82</td><td colspan="2">95</td><td>111</td><td>141</td><td>166</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
<tr><td colspan="14">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="7">1. Твердости чугуна Твердость, НВ, МПа Коэффициент К тв</td><td colspan="3">до 2150 1,0</td><td colspan="4">св. 2150 1,2</td></tr>
<tr><td colspan="7">2. Формы обрабатыва- Форма поверхности емой поверхности Коэффициент К ф</td><td colspan="3">прямолинейная 1,0</td><td colspan="4">криволинейная (фасонная) 1,2</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="6%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="14">Неполное штучное время Обработка плоскостей</td><td colspan="7">Долбежные станки</td></tr>
<tr><td colspan="14" rowspan="2">Сталь конструкционная, сигма = 590...740 МПа в</td><td colspan="7">Резцы из стали Р6М5</td></tr>
<tr><td colspan="7">Карта 51</td></tr>
<tr><td colspan="21">рисунок не приводится</td></tr>
<tr><td rowspan="4">N позиции</td><td>Шероховатость</td><td rowspan="2">Ширина обработки, В, мм,</td><td colspan="9">Заготовка из проката</td><td colspan="9">Поковка или отливка</td></tr>
<tr><td rowspan="3">и точность</td><td colspan="18">Длина обрабатываемой поверхности, l, мм, до</td></tr>
<tr><td rowspan="2">до</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>300</td><td colspan="2">400</td><td>500</td><td>50</td><td colspan="2">100</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td></tr>
<tr><td colspan="18">Время на поверхность, t , мин. нш</td></tr>
<tr><td>1</td><td>Rz 80;</td><td>25</td><td>2,6</td><td>3,2</td><td>4,0</td><td>4,6</td><td>5,0</td><td>5,3</td><td colspan="2">6,0</td><td>7,0</td><td>5,6</td><td colspan="2">6,4</td><td>6,6</td><td>7,2</td><td>7,5</td><td>8,0</td><td>8,5</td><td>9,5</td></tr>
<tr><td>2</td><td>14...12</td><td>50</td><td>3,6</td><td>4,4</td><td>5,5</td><td>6,2</td><td>7,0</td><td>7,7</td><td colspan="2">9,0</td><td>10</td><td>6,5</td><td colspan="2">7,5</td><td>8,5</td><td>9,0</td><td>10</td><td>11</td><td>13</td><td>15</td></tr>
<tr><td>3</td><td>квали-</td><td>75</td><td>4,1</td><td>5,8</td><td>7,2</td><td>8,4</td><td>9,3</td><td>11</td><td colspan="2">12</td><td>14</td><td>7,0</td><td colspan="2">8,5</td><td>11</td><td>12</td><td>13</td><td>15</td><td>17</td><td>20</td></tr>
<tr><td>4</td><td>тет</td><td>100</td><td>5,5</td><td>7,0</td><td>9,0</td><td>10</td><td>11</td><td>13</td><td colspan="2">15</td><td>19</td><td>7,5</td><td colspan="2">8,5</td><td>12</td><td>14</td><td>16</td><td>18</td><td>22</td><td>26</td></tr>
<tr><td>5</td><td></td><td>150</td><td>7,6</td><td>9,8</td><td>12</td><td>14</td><td>16</td><td>18</td><td colspan="2">22</td><td>26</td><td>9,0</td><td colspan="2">12</td><td>13</td><td>18</td><td>22</td><td>25</td><td>32</td><td>37</td></tr>
<tr><td>6</td><td></td><td>200</td><td>9,2</td><td>12</td><td>15</td><td>18</td><td>21</td><td>24</td><td colspan="2">29</td><td>34</td><td>10</td><td colspan="2">14</td><td>18</td><td>22</td><td>27</td><td>31</td><td>37</td><td>47</td></tr>
<tr><td>7</td><td></td><td>250</td><td>10</td><td>14</td><td>18</td><td>22</td><td>25</td><td>29</td><td colspan="2">35</td><td>42</td><td>11</td><td colspan="2">16</td><td>22</td><td>27</td><td>32</td><td>37</td><td>48</td><td>58</td></tr>
<tr><td>8</td><td></td><td>300</td><td>-</td><td>16</td><td>22</td><td>25</td><td>30</td><td>34</td><td colspan="2">42</td><td>49</td><td>-</td><td colspan="2">18</td><td>25</td><td>31</td><td>37</td><td>45</td><td>55</td><td>69</td></tr>
<tr><td>9</td><td></td><td>400</td><td>-</td><td>20</td><td>27</td><td>32</td><td>37</td><td>43</td><td colspan="2">55</td><td>65</td><td>-</td><td colspan="2">23</td><td>32</td><td>39</td><td>50</td><td>68</td><td>75</td><td>93</td></tr>
<tr><td>10</td><td></td><td>500</td><td>-</td><td>25</td><td>33</td><td>40</td><td>46</td><td>54</td><td colspan="2">68</td><td>80</td><td>-</td><td colspan="2">28</td><td>38</td><td>50</td><td>61</td><td>71</td><td>93</td><td>114</td></tr>
<tr><td colspan="3">Число проходов</td><td colspan="9">1</td><td colspan="9">2</td></tr>
<tr><td>11</td><td>Rz 40</td><td>25</td><td>5,8</td><td>7,2</td><td>9,0</td><td>10</td><td>11</td><td>12</td><td colspan="2">13</td><td>16</td><td>7,0</td><td colspan="2">8,6</td><td>10,8</td><td>11</td><td>12</td><td>13</td><td>14</td><td>17</td></tr>
<tr><td>12</td><td>...</td><td>50</td><td>8,0</td><td>10</td><td>12</td><td>14</td><td>16</td><td>17</td><td colspan="2">20</td><td>22</td><td>9,6</td><td colspan="2">12</td><td>14</td><td>15</td><td>18</td><td>19</td><td>21</td><td>24</td></tr>
<tr><td>13</td><td>Rz 20;</td><td>75</td><td>9,2</td><td>13</td><td>16</td><td>19</td><td>21</td><td>25</td><td colspan="2">27</td><td>31</td><td>11</td><td colspan="2">16</td><td>19</td><td>21</td><td>23</td><td>27</td><td>29</td><td>33</td></tr>
<tr><td>14</td><td>точ-</td><td>100</td><td>12</td><td>16</td><td>20</td><td>22</td><td>26</td><td>29</td><td colspan="2">34</td><td>43</td><td>14</td><td colspan="2">19</td><td>21</td><td>24</td><td>29</td><td>32</td><td>46</td><td>45</td></tr>
<tr><td>15</td><td>ность</td><td>150</td><td>17</td><td>22</td><td>28</td><td>33</td><td>36</td><td>40</td><td colspan="2">49</td><td>58</td><td>20</td><td colspan="2">26</td><td>34</td><td>36</td><td>40</td><td>44</td><td>52</td><td>61</td></tr>
<tr><td>16</td><td>измере-</td><td>200</td><td>21</td><td>27</td><td>35</td><td>40</td><td>47</td><td>54</td><td colspan="2">65</td><td>76</td><td>23</td><td colspan="2">30</td><td>38</td><td>44</td><td>52</td><td>59</td><td>69</td><td>80</td></tr>
<tr><td>17</td><td>ния</td><td>250</td><td>24</td><td>31</td><td>40</td><td>49</td><td>56</td><td>65</td><td colspan="2">79</td><td>94</td><td>26</td><td colspan="2">34</td><td>44</td><td>54</td><td>62</td><td>72</td><td>84</td><td>99</td></tr>
<tr><td>18</td><td>0,3...</td><td>300</td><td>-</td><td>36</td><td>49</td><td>56</td><td>67</td><td>76</td><td colspan="2">94</td><td>110</td><td>-</td><td colspan="2">40</td><td>54</td><td>62</td><td>74</td><td>84</td><td>99</td><td>117</td></tr>
<tr><td>19</td><td>0,5</td><td>400</td><td>-</td><td>45</td><td>61</td><td>72</td><td>83</td><td>97</td><td colspan="2">123</td><td>146</td><td>-</td><td colspan="2">48</td><td>65</td><td>76</td><td>88</td><td>103</td><td>130</td><td>186</td></tr>
<tr><td>20</td><td></td><td>500</td><td>-</td><td>56</td><td>74</td><td>90</td><td>103</td><td>121</td><td colspan="2">153</td><td>180</td><td>-</td><td colspan="2">59</td><td>78</td><td>95</td><td>109</td><td>128</td><td>162</td><td>191</td></tr>
<tr><td colspan="3">Число проходов</td><td colspan="9">2</td><td colspan="9">3</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td></tr>
<tr><td colspan="21">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="10">1. Предела прочности Прочность, сигма , МПа обрабатываемого в материала Коэффициент К пп</td><td colspan="5">до 590 0,9</td><td colspan="6">590...740 св. 740 1,0 1,2</td></tr>
<tr><td colspan="10">2. Формы обрабатыва- Поверхность емой поверхности Коэффициент К ф</td><td colspan="5">Прямолинейная 1,0</td><td colspan="6">Криволинейная (фасонная) 1,2</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="7%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="14">Неполное штучное время Долбление пазов, Rz 40...Rz 20; 11 квалитет</td><td colspan="5">Долбежные станки</td></tr>
<tr><td colspan="14" rowspan="2">Чугун серый, сталь конструкционная</td><td colspan="5">Резцы из стали Р6М5</td></tr>
<tr><td colspan="5">Карта 52</td></tr>
<tr><td colspan="19">рисунок не приводится</td></tr>
<tr><td rowspan="5">N позиции</td><td>Длина паза,</td><td colspan="2">Ширина паза,</td><td colspan="15">Обрабатываемый материал</td></tr>
<tr><td rowspan="4">l, мм, до</td><td colspan="2" rowspan="4">В, мм, до</td><td colspan="7">Чугун серый, НВ = 1760...2150 МПа</td><td colspan="8">Сталь конструкционная, сигма = 590...740 МПа в</td></tr>
<tr><td colspan="15">Глубина паза, Н, мм, до</td></tr>
<tr><td>3</td><td>5</td><td>10</td><td>15</td><td>20</td><td>30</td><td>40</td><td colspan="2">3</td><td>5</td><td>10</td><td>15</td><td>20</td><td>30</td><td>40</td></tr>
<tr><td colspan="15">Время на паз, t , мин. нш</td></tr>
<tr><td>1</td><td>50</td><td colspan="2">10</td><td>1,8</td><td>2,1</td><td>2,9</td><td>3,2</td><td>3,6</td><td>-</td><td>-</td><td colspan="2">3,2</td><td>3,5</td><td>4,3</td><td>5,0</td><td>6,0</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td></td><td colspan="2">20</td><td>1,7</td><td>1,9</td><td>2,5</td><td>3,2</td><td>3,8</td><td>4,2</td><td>5,0</td><td colspan="2">3,0</td><td>3,4</td><td>4,0</td><td>4,8</td><td>5,5</td><td>6,5</td><td>7,7</td></tr>
<tr><td>3</td><td>100</td><td colspan="2">10</td><td>2,2</td><td>2,8</td><td>4,1</td><td>4,7</td><td>5,2</td><td>-</td><td>-</td><td colspan="2">3,4</td><td>4,0</td><td>5,2</td><td>6,7</td><td>7,7</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td></td><td colspan="2">20</td><td>2,0</td><td>2,4</td><td>3,4</td><td>4,3</td><td>5,3</td><td>6,3</td><td>7,4</td><td colspan="2">3,3</td><td>3,8</td><td>5,0</td><td>6,5</td><td>7,5</td><td>8,6</td><td>11</td></tr>
<tr><td>5</td><td>150</td><td colspan="2">16</td><td>2,8</td><td>3,5</td><td>5,3</td><td>7,0</td><td>9,1</td><td>10</td><td>-</td><td colspan="2">4,0</td><td>4,6</td><td>7,0</td><td>9,0</td><td>12</td><td>14</td><td>-</td></tr>
<tr><td>6</td><td></td><td colspan="2">20</td><td>2,5</td><td>3,2</td><td>4,8</td><td>6,4</td><td>7,7</td><td>11</td><td>16</td><td colspan="2">3,8</td><td>4,5</td><td>6,5</td><td>8,6</td><td>11</td><td>13</td><td>17</td></tr>
<tr><td>7</td><td>200</td><td colspan="2">16</td><td>4,2</td><td>5,5</td><td>9,1</td><td>12</td><td>15</td><td>18</td><td>-</td><td colspan="2">4,5</td><td>5,2</td><td>7,7</td><td>11</td><td>14</td><td>16</td><td>-</td></tr>
<tr><td>8</td><td></td><td colspan="2">20</td><td>3,8</td><td>4,9</td><td>7,7</td><td>10</td><td>13</td><td>19</td><td>24</td><td colspan="2">4,4</td><td>5,0</td><td>7,0</td><td>10</td><td>12</td><td>15</td><td>20</td></tr>
<tr><td>9</td><td>300</td><td colspan="2">16</td><td>4,8</td><td>6,3</td><td>9,8</td><td>14</td><td>17</td><td>21</td><td>-</td><td colspan="2">5,0</td><td>6,0</td><td>9,0</td><td>14</td><td>16</td><td>20</td><td>-</td></tr>
<tr><td>10</td><td></td><td colspan="2">20</td><td>4,2</td><td>5,6</td><td>9,0</td><td>12</td><td>15</td><td>22</td><td>28</td><td colspan="2">4,5</td><td>5,6</td><td>9,0</td><td>13</td><td>15</td><td>19</td><td>27</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3" rowspan="2">Обрабатываемого материала</td><td colspan="5">Чугун, твердость, НВ, МПа</td><td colspan="9">Сталь конструкционная, Коррозисигма , МПа онносв тойкие</td><td colspan="2" rowspan="2">Жаропрочные</td></tr>
<tr><td colspan="5">до 1760... св. 1760 2150 2150</td><td colspan="4">до 590 590... 740</td><td colspan="5">св. 740</td></tr>
<tr><td colspan="3">Коэффициент</td><td colspan="5">0,9 1,0 1,2</td><td colspan="4">0,9 1,0</td><td colspan="5">1,2 1,35</td><td colspan="2">1,45</td></tr>
</table>


<a id="p101714"></a>Примечания: 1. При долблении пазов с шероховатостью Ra 2,5; 9 квалитет время по карте следует применять с коэффициентом К = 1,2.
2. <a id="p101715"></a>При долблении шлицевых отверстий время по карте следует применять с коэффициентом К = 2,0.






<a id="p101716"></a>

<table>
<colgroup><col width="3%"><col width="7%"><col width="4%"><col width="7%"><col width="4%"><col width="7%"><col width="6%"><col width="7%"><col width="6%"><col width="5%"><col width="1%"><col width="6%"><col width="7%"><col width="6%"><col width="7%"><col width="6%"><col width="7%"><col width="6%"></colgroup>
<tr><td colspan="10" rowspan="2">Режимы резания</td><td colspan="8">Горизонтально- и вертикально-фрезерные станки</td></tr>
<tr><td colspan="5">Приложение 1</td><td colspan="3">лист 1</td></tr>
<tr><td colspan="18">Обработка поверхностей. Фрезы торцовые</td></tr>
<tr><td rowspan="6">N позиции</td><td>Обрабатываемый</td><td>Материал</td><td>Шероховатость</td><td>Глубина</td><td colspan="13">Диаметр фрезы, D, мм, и число зубьев, Z</td></tr>
<tr><td rowspan="5">материал</td><td rowspan="5">режущей части</td><td rowspan="5">поверхности</td><td>резания, t, мм</td><td colspan="2">80/10</td><td colspan="2">125/14</td><td colspan="3">160/16</td><td colspan="2">200/20</td><td colspan="2">250/24</td><td colspan="2">315/30</td></tr>
<tr><td rowspan="4">до</td><td colspan="13">Ширина обрабатываемой поверхности, В, мм</td></tr>
<tr><td colspan="2">50</td><td colspan="2">75</td><td colspan="3">110</td><td colspan="2">150</td><td colspan="2">200</td><td colspan="2">250</td></tr>
<tr><td colspan="13">Режимы резания</td></tr>
<tr><td>n, об./мин.</td><td>S, мм/мин.</td><td>n, об./мин.</td><td>S, мм/мин.</td><td colspan="2">n, об./мин.</td><td>S, мм/мин.</td><td>n, об./мин.</td><td>S, мм/мин.</td><td>n, об./мин.</td><td>S, мм/мин.</td><td>n, об./мин.</td><td>S, мм/мин.</td></tr>
<tr><td>1</td><td>Чугун</td><td>ВК8</td><td>Rz 80;</td><td>3</td><td>480</td><td>960</td><td>300</td><td>750</td><td colspan="2">150</td><td>480</td><td>96</td><td>480</td><td>96</td><td>600</td><td>75</td><td>480</td></tr>
<tr><td>2</td><td>серый</td><td></td><td>14...12</td><td>5</td><td>380</td><td>750</td><td>190</td><td>490</td><td colspan="2">96</td><td>300</td><td>75</td><td>300</td><td>60</td><td>380</td><td>48</td><td>300</td></tr>
<tr><td>3</td><td rowspan="2"></td><td rowspan="2"></td><td>квалитет</td><td>8</td><td>240</td><td>480</td><td>120</td><td>300</td><td colspan="2">96</td><td>190</td><td>75</td><td>190</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>Rz 40 -</td><td>3</td><td>600</td><td>480</td><td>380</td><td>300</td><td colspan="2">300</td><td>240</td><td>240</td><td>190</td><td>190</td><td>160</td><td>160</td><td>120</td></tr>
<tr><td>5</td><td></td><td></td><td>Rz 20;</td><td>5</td><td>480</td><td>380</td><td>300</td><td>240</td><td colspan="2">240</td><td>190</td><td>190</td><td>150</td><td>150</td><td>120</td><td>120</td><td>90</td></tr>
<tr><td>6</td><td rowspan="2"></td><td rowspan="2"></td><td>11 квалитет</td><td>8</td><td>380</td><td>300</td><td>240</td><td>190</td><td colspan="2">150</td><td>120</td><td>150</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>Rz 20; 11 квалитет</td><td>2</td><td>960</td><td>750</td><td>600</td><td>480</td><td colspan="2">480</td><td>380</td><td>380</td><td>300</td><td>300</td><td>240</td><td>240</td><td>190</td></tr>
<tr><td>8</td><td>Сталь</td><td>Т5К10</td><td>Rz 80;</td><td>3</td><td>380</td><td>380</td><td>300</td><td>300</td><td colspan="2">150</td><td>190</td><td>120</td><td>160</td><td>96</td><td>150</td><td>75</td><td>140</td></tr>
<tr><td>9</td><td></td><td></td><td>14...12</td><td>5</td><td>290</td><td>190</td><td>150</td><td>150</td><td colspan="2">120</td><td>130</td><td>100</td><td>120</td><td>80</td><td>110</td><td>65</td><td>100</td></tr>
<tr><td>10</td><td rowspan="2"></td><td></td><td>квалитет</td><td>8</td><td>160</td><td>180</td><td>120</td><td>120</td><td colspan="2">100</td><td>100</td><td>90</td><td>100</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td></td><td>Rz 40 -</td><td>3</td><td>380</td><td>300</td><td>300</td><td>240</td><td colspan="2">240</td><td>190</td><td>190</td><td>150</td><td>160</td><td>120</td><td>150</td><td>110</td></tr>
<tr><td>12</td><td></td><td></td><td>Rz 20;</td><td>5</td><td>240</td><td>190</td><td>150</td><td>120</td><td colspan="2">120</td><td>96</td><td>96</td><td>75</td><td>80</td><td>100</td><td>65</td><td>100</td></tr>
<tr><td>13</td><td rowspan="2"></td><td rowspan="2"></td><td>11 квалитет</td><td>8</td><td>200</td><td>160</td><td>120</td><td>100</td><td colspan="2">100</td><td>96</td><td>80</td><td>65</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td>Rz 20; 11 квалитет</td><td>2</td><td>1200</td><td>600</td><td>960</td><td>400</td><td colspan="2">750</td><td>320</td><td>600</td><td>260</td><td>480</td><td>200</td><td>380</td><td>160</td></tr>
<tr><td>15</td><td>Сталь</td><td>Р6М5</td><td>Rz 80;</td><td>3</td><td>150</td><td>190</td><td>96</td><td>150</td><td colspan="2">75</td><td>150</td><td>60</td><td>150</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td></td><td></td><td>14...12</td><td>5</td><td>120</td><td>150</td><td>75</td><td>120</td><td colspan="2">60</td><td>110</td><td>48</td><td>100</td><td>48</td><td>90</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td rowspan="2"></td><td rowspan="2"></td><td>квалитет</td><td>8</td><td>120</td><td>150</td><td>75</td><td>120</td><td colspan="2">60</td><td>120</td><td>48</td><td>96</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td>Rz 20; 11 квалитет</td><td>2</td><td>240</td><td>196</td><td>150</td><td>150</td><td colspan="2">120</td><td>96</td><td>96</td><td>75</td><td>75</td><td>60</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td>Медные</td><td></td><td>Rz 80;</td><td>3</td><td></td><td>750</td><td></td><td>600</td><td colspan="2"></td><td>600</td><td></td><td>600</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>сплавы</td><td></td><td>14...12</td><td>5</td><td>240</td><td>600</td><td>190</td><td>480</td><td colspan="2">120</td><td>480</td><td>96</td><td>480</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>21</td><td>НВ =</td><td></td><td>квалитет</td><td>8</td><td></td><td>480</td><td></td><td>380</td><td colspan="2"></td><td>380</td><td></td><td>380</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>22</td><td>980... 1370 МПа</td><td rowspan="2"></td><td></td><td>12</td><td></td><td>380</td><td></td><td>380</td><td colspan="2"></td><td>300</td><td></td><td>300</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>23</td><td>и алюминиевые</td><td>Rz 20; 11 квалитет</td><td>2</td><td>380</td><td>300</td><td>240</td><td>190</td><td colspan="2">190</td><td>150</td><td>150</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="8%"><col width="14%"><col width="9%"><col width="9%"><col width="8%"><col width="7%"><col width="2%"><col width="8%"><col width="9%"><col width="6%"><col width="2%"><col width="9%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Режимы резания при обработке плоскостей Фрезы концевые. Обработка поверхностей</td><td colspan="7">Горизонтально-вертикально-фрезерные станки</td></tr>
<tr><td colspan="4">Приложение 1</td><td colspan="3">лист 2</td></tr>
<tr><td rowspan="6">N позиции</td><td>Диаметр фрезы,</td><td rowspan="6">Шероховатость поверхности</td><td>Глубина резания,</td><td colspan="10">Обрабатываемый материал</td></tr>
<tr><td>D, мм, и число зубьев,</td><td rowspan="5">t, мм, до</td><td colspan="5">Сталь</td><td colspan="3">Чугун серый</td><td colspan="2">Медные сплавы</td></tr>
<tr><td rowspan="4">z</td><td colspan="10">Режущий инструмент</td></tr>
<tr><td colspan="2">Фрезы концевые из стали Р6М5</td><td colspan="3">Фрезы концевые с пластинками Т5К10, Т15К6</td><td colspan="5">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="10">Режимы резания</td></tr>
<tr><td>n, об./мин.</td><td>S, мм/мин.</td><td colspan="2">n, об./мин.</td><td>S, мм/мин.</td><td>n, об./мин.</td><td colspan="2">S, мм/мин.</td><td>n, об./мин.</td><td>S, мм/мин.</td></tr>
<tr><td>24</td><td>16</td><td>Rz 80</td><td>3</td><td>1180</td><td>190</td><td colspan="2">-</td><td>-</td><td>600</td><td colspan="2">150</td><td>1180</td><td>250</td></tr>
<tr><td>25</td><td>-----</td><td></td><td>5</td><td>950</td><td>150</td><td colspan="2">1500</td><td>250</td><td>600</td><td colspan="2">125</td><td>1180</td><td>250</td></tr>
<tr><td>26</td><td>3...4</td><td>Rz 40...Rz 20</td><td>1...2</td><td>1180</td><td>125</td><td colspan="2">1600</td><td>200</td><td>750</td><td colspan="2">150</td><td>1600</td><td>250</td></tr>
<tr><td>27</td><td>20</td><td>Rz 80</td><td>3</td><td>750</td><td>190</td><td colspan="2">1500</td><td>375</td><td>475</td><td colspan="2">190</td><td>950</td><td>300</td></tr>
<tr><td>28</td><td>-----</td><td></td><td>5</td><td>750</td><td>150</td><td colspan="2">1500</td><td>300</td><td>375</td><td colspan="2">150</td><td>950</td><td>250</td></tr>
<tr><td>29</td><td>5...4</td><td>Rz 40...Rz 20</td><td>1...2</td><td>1180</td><td>250</td><td colspan="2">1250</td><td>250</td><td>750</td><td colspan="2">250</td><td>1180</td><td>375</td></tr>
<tr><td>30</td><td>20</td><td>Rz 80</td><td>3</td><td>750</td><td>150</td><td colspan="2">-</td><td>-</td><td>475</td><td colspan="2">150</td><td>950</td><td>300</td></tr>
<tr><td>31</td><td>--</td><td></td><td>5</td><td>750</td><td>125</td><td colspan="2">-</td><td>-</td><td>375</td><td colspan="2">125</td><td>950</td><td>250</td></tr>
<tr><td>32</td><td>3</td><td>Rz 40...Rz 20</td><td>1...2</td><td>950</td><td>150</td><td colspan="2">-</td><td>-</td><td>750</td><td colspan="2">190</td><td>1180</td><td>300</td></tr>
<tr><td>33</td><td>25</td><td>Rz 80</td><td>3</td><td>600</td><td>190</td><td colspan="2">1500</td><td>375</td><td>475</td><td colspan="2">190</td><td>750</td><td>300</td></tr>
<tr><td>34</td><td>-----</td><td></td><td>5</td><td>600</td><td>150</td><td colspan="2">1180</td><td>300</td><td>375</td><td colspan="2">150</td><td>750</td><td>250</td></tr>
<tr><td>35</td><td>5...4</td><td>Rz 40...Rz 20</td><td>1...2</td><td>750</td><td>190</td><td colspan="2">800</td><td>200</td><td>600</td><td colspan="2">190</td><td>950</td><td>300</td></tr>
<tr><td>36</td><td>25</td><td>Rz 80</td><td>3</td><td>600</td><td>150</td><td colspan="2">-</td><td>-</td><td>475</td><td colspan="2">150</td><td>750</td><td>250</td></tr>
<tr><td>37</td><td>--</td><td></td><td>5</td><td>475</td><td>125</td><td colspan="2">-</td><td>-</td><td>375</td><td colspan="2">125</td><td>750</td><td>190</td></tr>
<tr><td>38</td><td>3</td><td>Rz 40...Rz 20</td><td>1...2</td><td>750</td><td>150</td><td colspan="2">-</td><td>-</td><td>600</td><td colspan="2">150</td><td>750</td><td>250</td></tr>
<tr><td>39</td><td>32</td><td>Rz 80</td><td>3</td><td>375</td><td>190</td><td colspan="2">-</td><td>-</td><td>375</td><td colspan="2">250</td><td>600</td><td>375</td></tr>
<tr><td>40</td><td>--</td><td></td><td>5</td><td>375</td><td>150</td><td colspan="2">-</td><td>-</td><td>300</td><td colspan="2">190</td><td>475</td><td>250</td></tr>
<tr><td>41</td><td>6</td><td>Rz 40...Rz 20</td><td>1...2</td><td>600</td><td>250</td><td colspan="2">-</td><td>-</td><td>475</td><td colspan="2">250</td><td>600</td><td>300</td></tr>
<tr><td>42</td><td>32</td><td>Rz 80</td><td>3</td><td>375</td><td>150</td><td colspan="2">950</td><td>300</td><td>300</td><td colspan="2">190</td><td>600</td><td>300</td></tr>
<tr><td>43</td><td>--</td><td></td><td>5</td><td>375</td><td>125</td><td colspan="2">950</td><td>250</td><td>300</td><td colspan="2">150</td><td>475</td><td>250</td></tr>
<tr><td>44</td><td>4</td><td>Rz 40...Rz 20</td><td>1...2</td><td>475</td><td>190</td><td colspan="2">800</td><td>200</td><td>475</td><td colspan="2">190</td><td>600</td><td>250</td></tr>
<tr><td>45</td><td>40</td><td>Rz 80</td><td>3</td><td>300</td><td>190</td><td colspan="2">950</td><td>625</td><td>300</td><td colspan="2">250</td><td>475</td><td>300</td></tr>
<tr><td>46</td><td>--</td><td></td><td>5</td><td>300</td><td>150</td><td colspan="2">950</td><td>375</td><td>300</td><td colspan="2">190</td><td>475</td><td>250</td></tr>
<tr><td>47</td><td>6</td><td>Rz 40...Rz 20</td><td>8</td><td>300</td><td>95</td><td colspan="2">750</td><td>250</td><td>235</td><td colspan="2">125</td><td>475</td><td>190</td></tr>
<tr><td>48</td><td></td><td></td><td>1...2</td><td>375</td><td>190</td><td colspan="2">700</td><td>190</td><td>375</td><td colspan="2">190</td><td>475</td><td>300</td></tr>
<tr><td>49</td><td>40</td><td>Rz 80</td><td>3</td><td>300</td><td>150</td><td colspan="2">-</td><td>-</td><td>300</td><td colspan="2">190</td><td>475</td><td>250</td></tr>
<tr><td>50</td><td>--</td><td></td><td>5</td><td>300</td><td>125</td><td colspan="2">-</td><td>-</td><td>235</td><td colspan="2">150</td><td>475</td><td>190</td></tr>
<tr><td>51</td><td>4</td><td>Rz 40...Rz 20</td><td>8</td><td>275</td><td>75</td><td colspan="2">-</td><td>-</td><td>235</td><td colspan="2">95</td><td>475</td><td>150</td></tr>
<tr><td>52</td><td></td><td></td><td>1...2</td><td>375</td><td>150</td><td colspan="2">-</td><td>-</td><td>375</td><td colspan="2">150</td><td>475</td><td>250</td></tr>
<tr><td>53</td><td>50</td><td>Rz 80</td><td>3</td><td>235</td><td>150</td><td colspan="2">750</td><td>500</td><td>300</td><td colspan="2">250</td><td>375</td><td>300</td></tr>
<tr><td>54</td><td>--</td><td></td><td>5</td><td>235</td><td>125</td><td colspan="2">600</td><td>300</td><td>235</td><td colspan="2">190</td><td>375</td><td>250</td></tr>
<tr><td>55</td><td>6</td><td>Rz 40...Rz 20</td><td>8</td><td>235</td><td>95</td><td colspan="2">600</td><td>250</td><td>190</td><td colspan="2">125</td><td>300</td><td>150</td></tr>
<tr><td>56</td><td></td><td></td><td>1...2</td><td>375</td><td>190</td><td colspan="2">700</td><td>190</td><td>375</td><td colspan="2">150</td><td>375</td><td>250</td></tr>
<tr><td>57</td><td>50</td><td>Rz 80</td><td>3</td><td>235</td><td>125</td><td colspan="2">-</td><td>-</td><td>235</td><td colspan="2">190</td><td>375</td><td>250</td></tr>
<tr><td>58</td><td>--</td><td></td><td>5</td><td>190</td><td>95</td><td colspan="2">-</td><td>-</td><td>235</td><td colspan="2">150</td><td>375</td><td>190</td></tr>
<tr><td>59</td><td>4</td><td>Rz 40...Rz 20</td><td>8</td><td>190</td><td>63</td><td colspan="2">-</td><td>-</td><td>190</td><td colspan="2">95</td><td>300</td><td>125</td></tr>
<tr><td>60</td><td></td><td></td><td>1...2</td><td>250</td><td>125</td><td colspan="2">-</td><td>-</td><td>375</td><td colspan="2">125</td><td>375</td><td>190</td></tr>
</table>


<a id="p101788"></a>Примечания: 1. Меньшее число зубьев у фрез с пластинками Т5К10.
2. <a id="p101789"></a>Режимы резания приведены для обработки поверхности с шероховатостью Rz 80 фрезами Т5К10, а с шероховатостью Rz 40...Rz 20 - фрезами Т15К6.


<table>
<colgroup><col width="5%"><col width="10%"><col width="12%"><col width="8%"><col width="12%"><col width="10%"><col width="12%"><col width="10%"><col width="12%"><col width="10%"></colgroup>
<tr><td colspan="5" rowspan="2">Режимы резания</td><td colspan="5">Горизонтально-вертикально-фрезерные станки</td></tr>
<tr><td colspan="3">Приложение 1</td><td colspan="2">лист 3</td></tr>
<tr><td colspan="10">Фрезы концевые. Обработка уступов Rz 40...Rz 20</td></tr>
<tr><td rowspan="6">N позиции</td><td>Диаметр фрезы,</td><td rowspan="6">Ширина обрабатываемой поверхности, В, мм</td><td>Глубина</td><td colspan="6">Обрабатываемый материал</td></tr>
<tr><td>D, мм, и число</td><td>резания,</td><td colspan="2">Сталь</td><td colspan="2">Чугун серый</td><td colspan="2">Медные сплавы</td></tr>
<tr><td rowspan="4">зубьев, z</td><td>t, мм,</td><td colspan="6">Режущий инструмент</td></tr>
<tr><td rowspan="3">до</td><td colspan="2">Фрезы концевые из стали Р6М5</td><td colspan="2">Фрезы концевые из стали Р6М5</td><td colspan="2">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="6">Режимы резания</td></tr>
<tr><td>n, об./мин.</td><td>S, мм/мин.</td><td>n, об./мин.</td><td>S, мм/мин.</td><td>n, об./мин.</td><td>S, мм/мин.</td></tr>
<tr><td>61</td><td></td><td></td><td>5</td><td>980</td><td>150</td><td>750</td><td>190</td><td>950</td><td>250</td></tr>
<tr><td>62</td><td>16/4</td><td>12...18</td><td>10</td><td>150</td><td>125</td><td>600</td><td>150</td><td>750</td><td>190</td></tr>
<tr><td>63</td><td></td><td></td><td>20</td><td>600</td><td>95</td><td>600</td><td>125</td><td>600</td><td>150</td></tr>
<tr><td>64</td><td>20/5</td><td></td><td>30</td><td>475</td><td>63</td><td>375</td><td>75</td><td>475</td><td>125</td></tr>
<tr><td>65</td><td></td><td></td><td>40</td><td>375</td><td>50</td><td>300</td><td>63</td><td>375</td><td>75</td></tr>
<tr><td>66</td><td></td><td></td><td>10</td><td>475</td><td>125</td><td>375</td><td>125</td><td>950</td><td>250</td></tr>
<tr><td>67</td><td></td><td></td><td>20</td><td>475</td><td>95</td><td>300</td><td>95</td><td>600</td><td>190</td></tr>
<tr><td>68</td><td></td><td></td><td>30</td><td>375</td><td>63</td><td>235</td><td>75</td><td>475</td><td>150</td></tr>
<tr><td>69</td><td>25/5</td><td>18</td><td>45</td><td>300</td><td>50</td><td>235</td><td>63</td><td>475</td><td>125</td></tr>
<tr><td>70</td><td></td><td></td><td>10</td><td>475</td><td>125</td><td>300</td><td>95</td><td>600</td><td>190</td></tr>
<tr><td>71</td><td>25/5</td><td>22</td><td>20</td><td>375</td><td>95</td><td>300</td><td>95</td><td>475</td><td>150</td></tr>
<tr><td>72</td><td></td><td></td><td>30</td><td>300</td><td>63</td><td>235</td><td>63</td><td>475</td><td>125</td></tr>
<tr><td>73</td><td></td><td></td><td>45</td><td>300</td><td>50</td><td>235</td><td>50</td><td>375</td><td>95</td></tr>
<tr><td>74</td><td></td><td></td><td>10</td><td>300</td><td>95</td><td>375</td><td>125</td><td>475</td><td>190</td></tr>
<tr><td>75</td><td></td><td></td><td>20</td><td>235</td><td>75</td><td>235</td><td>95</td><td>375</td><td>150</td></tr>
<tr><td>76</td><td>32/6</td><td>25</td><td>30</td><td>235</td><td>63</td><td>235</td><td>75</td><td>300</td><td>125</td></tr>
<tr><td>77</td><td></td><td></td><td>40</td><td>190</td><td>50</td><td>190</td><td>63</td><td>235</td><td>75</td></tr>
<tr><td>78</td><td></td><td></td><td>60</td><td>150</td><td>31,5</td><td>150</td><td>50</td><td>190</td><td>65</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="10%"><col width="10%"><col width="6%"><col width="5%"><col width="10%"><col width="11%"><col width="10%"><col width="11%"><col width="10%"></colgroup>
<tr><td colspan="5" rowspan="2">Режимы резания</td><td colspan="6">Горизонтально-вертикально-фрезерные станки</td></tr>
<tr><td colspan="6">Приложение 1 лист 4</td></tr>
<tr><td colspan="11">Фрезы концевые. Обработка уступов Rz 40...Rz 20</td></tr>
<tr><td rowspan="6">N позиции</td><td>Диаметр фрезы,</td><td rowspan="2">Ширина обрабатываемой</td><td rowspan="6">Глубина резания, t, мм, до</td><td colspan="7">Обрабатываемый материал</td></tr>
<tr><td>D, мм, и число</td><td colspan="3">Сталь</td><td colspan="2">Чугун серый</td><td colspan="2">Медные сплавы</td></tr>
<tr><td rowspan="4">зубьев, z</td><td>поверхности,</td><td colspan="7">Режущий инструмент</td></tr>
<tr><td rowspan="3">В, мм</td><td colspan="3">Фрезы концевые из стали Р6М5</td><td colspan="2">Фрезы концевые из стали Р6М5</td><td colspan="2">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="7">Режимы резания</td></tr>
<tr><td colspan="2">n, об./мин.</td><td>S, мм/мин.</td><td>n, об./мин.</td><td>S, мм/мин.</td><td>n, об./мин.</td><td>S, мм/мин.</td></tr>
<tr><td>79</td><td></td><td></td><td>10</td><td colspan="2">300</td><td>95</td><td>235</td><td>125</td><td>375</td><td>150</td></tr>
<tr><td>80</td><td></td><td></td><td>20</td><td colspan="2">235</td><td>75</td><td>190</td><td>95</td><td>300</td><td>125</td></tr>
<tr><td>81</td><td>40/6</td><td>38</td><td>30</td><td colspan="2">190</td><td>50</td><td>190</td><td>75</td><td>235</td><td>95</td></tr>
<tr><td>82</td><td></td><td></td><td>40</td><td colspan="2">190</td><td>37,5</td><td>150</td><td>63</td><td>190</td><td>75</td></tr>
<tr><td>83</td><td></td><td></td><td>60</td><td colspan="2">190</td><td>31,5</td><td>150</td><td>50</td><td>150</td><td>63</td></tr>
<tr><td>84</td><td></td><td></td><td>10</td><td colspan="2">235</td><td>95</td><td>235</td><td>125</td><td>475</td><td>190</td></tr>
<tr><td>85</td><td></td><td></td><td>20</td><td colspan="2">190</td><td>75</td><td>190</td><td>95</td><td>375</td><td>150</td></tr>
<tr><td>86</td><td></td><td>18</td><td>30</td><td colspan="2">150</td><td>63</td><td>190</td><td>75</td><td>300</td><td>125</td></tr>
<tr><td>87</td><td></td><td></td><td>40</td><td colspan="2">150</td><td>50</td><td>150</td><td>63</td><td>235</td><td>95</td></tr>
<tr><td>88</td><td></td><td></td><td>60</td><td colspan="2">150</td><td>37,5</td><td>150</td><td>50</td><td>235</td><td>75</td></tr>
<tr><td>89</td><td></td><td></td><td>10</td><td colspan="2">235</td><td>95</td><td>235</td><td>125</td><td>375</td><td>150</td></tr>
<tr><td>90</td><td></td><td></td><td>20</td><td colspan="2">190</td><td>63</td><td>190</td><td>75</td><td>300</td><td>125</td></tr>
<tr><td>91</td><td>50/6</td><td>30</td><td>30</td><td colspan="2">150</td><td>50</td><td>150</td><td>63</td><td>235</td><td>95</td></tr>
<tr><td>92</td><td></td><td></td><td>40</td><td colspan="2">150</td><td>37,5</td><td>150</td><td>50</td><td>235</td><td>75</td></tr>
<tr><td>93</td><td></td><td></td><td>60</td><td colspan="2">118</td><td>31,5</td><td>118</td><td>37,5</td><td>150</td><td>63</td></tr>
<tr><td>94</td><td></td><td></td><td>10</td><td colspan="2">235</td><td>75</td><td>235</td><td>95</td><td>375</td><td>125</td></tr>
<tr><td>95</td><td></td><td></td><td>20</td><td colspan="2">190</td><td>50</td><td>190</td><td>75</td><td>300</td><td>95</td></tr>
<tr><td>96</td><td></td><td>45</td><td>30</td><td colspan="2">150</td><td>37,5</td><td>150</td><td>50</td><td>235</td><td>75</td></tr>
<tr><td>97</td><td></td><td></td><td>40</td><td colspan="2">150</td><td>31,5</td><td>118</td><td>37,5</td><td>190</td><td>63</td></tr>
<tr><td>98</td><td></td><td></td><td>60</td><td colspan="2">118</td><td>25</td><td>118</td><td>31,5</td><td>190</td><td>50</td></tr>
</table>







<a id="p101840"></a>

<table>
<colgroup><col width="4%"><col width="9%"><col width="8%"><col width="14%"><col width="8%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"></colgroup>
<tr><td colspan="11" rowspan="2">Режимы резания</td><td colspan="11">Продольно-фрезерные станки</td></tr>
<tr><td colspan="11">Приложение 2</td></tr>
<tr><td colspan="22">Фрезы торцовые. Обработка плоскостей</td></tr>
<tr><td rowspan="5">N позиции</td><td>Материал режущей</td><td rowspan="5">Обрабатываемый материал</td><td rowspan="5">Шероховатость поверхности</td><td>Глубина резания</td><td colspan="17">Диаметр фрезы, D, мм, и число зубьев, z <a href="#p101861">&lt;*&gt;</a></td></tr>
<tr><td rowspan="4">части</td><td rowspan="4">t, мм, до</td><td colspan="2">80 -- 10</td><td colspan="2">100 ------ 8...10</td><td colspan="3">125 ------ 8...14</td><td colspan="3">160 ------- 10...16</td><td colspan="3">200 ------- 12...20</td><td colspan="2">250 ------- 14...20</td><td colspan="2">320 ------- 18...24</td></tr>
<tr><td colspan="17">Ширина обрабатываемой поверхности, В, мм</td></tr>
<tr><td colspan="2">50</td><td colspan="2">60</td><td colspan="3">75</td><td colspan="3">110</td><td colspan="3">150</td><td colspan="2">200</td><td colspan="2">250</td></tr>
<tr><td colspan="17">Режимы резания (n, об./мин.; S, мм/мин.)</td></tr>
<tr><td>1</td><td>Т15К6</td><td>Сталь</td><td>Rz 80</td><td>5</td><td>-</td><td>-</td><td>300</td><td>300</td><td>235</td><td colspan="2">235</td><td colspan="2">95</td><td>118</td><td colspan="2">75</td><td>118</td><td>60</td><td>95</td><td>47,5</td><td>60</td></tr>
<tr><td>2</td><td>Т5К10</td><td></td><td></td><td>8</td><td>-</td><td>-</td><td>190</td><td>190</td><td>150</td><td colspan="2">150</td><td colspan="2">95</td><td>75</td><td colspan="2">75</td><td>60</td><td>60</td><td>50</td><td>47,5</td><td>30</td></tr>
<tr><td>3</td><td></td><td rowspan="2"></td><td>Rz 40...Rz 20</td><td>2</td><td>-</td><td>-</td><td>475</td><td>235</td><td>375</td><td colspan="2">190</td><td colspan="2">300</td><td>150</td><td colspan="2">235</td><td>118</td><td>190</td><td>95</td><td>150</td><td>75</td></tr>
<tr><td>4</td><td>Р6М5</td><td>Rz 80</td><td>5</td><td>190</td><td>95</td><td>150</td><td>75</td><td>118</td><td colspan="2">75</td><td colspan="2">95</td><td>75</td><td colspan="2">75</td><td>75</td><td>60</td><td>60</td><td>47,5</td><td>50</td></tr>
<tr><td>5</td><td></td><td></td><td></td><td>8</td><td>150</td><td>60</td><td>150</td><td>60</td><td>118</td><td colspan="2">75</td><td colspan="2">95</td><td>50</td><td colspan="2">75</td><td>60</td><td>60</td><td>60</td><td>47,5</td><td>50</td></tr>
<tr><td>6</td><td></td><td></td><td>Rz 40...Rz 20</td><td>2</td><td>235</td><td>118</td><td>190</td><td>95</td><td>150</td><td colspan="2">75</td><td colspan="2">118</td><td>60</td><td colspan="2">95</td><td>50</td><td>95</td><td>50</td><td>75</td><td>40</td></tr>
<tr><td>7</td><td>ВК8</td><td>Чугун</td><td>Rz 80</td><td>8</td><td>300</td><td>600</td><td>235</td><td>500</td><td>150</td><td colspan="2">400</td><td colspan="2">95</td><td>235</td><td colspan="2">75</td><td>190</td><td>60</td><td>118</td><td>47,5</td><td>95</td></tr>
<tr><td>8</td><td>ВК6</td><td>серый</td><td></td><td>12</td><td>190</td><td>400</td><td>150</td><td>300</td><td>118</td><td colspan="2">235</td><td colspan="2">95</td><td>150</td><td colspan="2">75</td><td>118</td><td>60</td><td>95</td><td>47,5</td><td>60</td></tr>
<tr><td>9</td><td></td><td></td><td>Rz 40...Rz 20</td><td>2</td><td>600</td><td>300</td><td>600</td><td>300</td><td>600</td><td colspan="2">300</td><td colspan="2">475</td><td>235</td><td colspan="2">375</td><td>190</td><td>300</td><td>150</td><td>235</td><td>118</td></tr>
<tr><td colspan="22">Поправочные коэффициенты на режимы резания в зависимости от:</td></tr>
<tr><td colspan="16">Предела прочности или Обрабатываемый материал Сталь конструкционная</td><td colspan="6">Чугун серый</td></tr>
<tr><td colspan="9">обрабатываемого Предел прочности, сигма , МПа до 590 материала в Твердость НВ, ГПа - Коэффициент К 1,1 пп</td><td colspan="4">590...740 - 1,0</td><td colspan="3">св. 740 - 0,8</td><td colspan="3">- до 2150 1,0</td><td colspan="3">- св. 2150 0,8</td></tr>
</table>



<a id="p101860"></a>

---

<a id="p101861"></a><*> Меньшее число зубьев у фрез с пластинками Т5К10.

<a id="p101862"></a>Примечания: 1. При обработке торцовыми фрезами Т15К6 режимы резания принимать с коэффициентом К = 1,5.






<a id="p101863"></a>

<table>
<colgroup><col width="4%"><col width="7%"><col width="8%"><col width="8%"><col width="8%"><col width="7%"><col width="3%"><col width="5%"><col width="2%"><col width="10%"><col width="7%"><col width="3%"><col width="7%"><col width="2%"><col width="5%"><col width="7%"><col width="3%"><col width="7%"></colgroup>
<tr><td colspan="18">Режимы резания Продольно-строгальные станки</td></tr>
<tr><td colspan="18">Приложение 3</td></tr>
<tr><td rowspan="6">N позиции</td><td colspan="2">Шероховатость поверхности и</td><td rowspan="6">Вид обработки</td><td rowspan="2">Глубина резания, мм, до</td><td colspan="13">Обрабатываемый материал</td></tr>
<tr><td colspan="2" rowspan="5">точность</td><td colspan="6">Сталь</td><td colspan="7">Чугун</td></tr>
<tr><td>или ширина</td><td colspan="13">Режущий инструмент</td></tr>
<tr><td rowspan="3">паза, В, мм, до</td><td colspan="4">Резцы из стали Р6М5</td><td colspan="2">Резцы с пластинками Т5К10, Т15К6</td><td colspan="4">Резцы из стали Р6М5</td><td colspan="3">Резцы с пластинками ВК8, ВК6</td></tr>
<tr><td colspan="13">Режимы резания</td></tr>
<tr><td colspan="2">S, мм/дв. ход</td><td colspan="2">v, м/мин.</td><td>S, мм/дв. ход</td><td>v, м/мин.</td><td colspan="2">S, мм/дв. ход</td><td colspan="2">v, м/мин.</td><td colspan="2">S, мм/дв. ход</td><td>v, м/мин.</td></tr>
<tr><td>1</td><td>Rz 80</td><td>14 квалитет</td><td>Строгание</td><td>5</td><td colspan="2">-</td><td colspan="2">-</td><td>0,9</td><td>33</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">2,5</td><td></td></tr>
<tr><td>2</td><td></td><td>12 ква-</td><td>плоско-</td><td>12</td><td colspan="2">-</td><td colspan="2">-</td><td>0,9</td><td>28</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">2,0</td><td>27</td></tr>
<tr><td>3</td><td></td><td>литет</td><td rowspan="2">стей</td><td>20</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">1,2</td><td></td></tr>
<tr><td>4</td><td>Rz 40</td><td>11 квалитет</td><td>2</td><td colspan="2">0,7</td><td colspan="2">25</td><td>0,6</td><td>58</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">3</td><td>24</td></tr>
<tr><td>5</td><td>Rz 20</td><td>11 квалитет</td><td></td><td>0,8</td><td colspan="2">2,0</td><td colspan="2">11</td><td></td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">15</td><td>12,5</td></tr>
<tr><td>6</td><td>Rа 2,5</td><td>8 квалитет</td><td></td><td>0,2</td><td colspan="2">8,0</td><td colspan="2">12</td><td></td><td></td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">12</td><td>7,0</td></tr>
<tr><td>7</td><td colspan="2">Rz 80; 14...</td><td>Строга-</td><td>10</td><td colspan="2">0,25</td><td colspan="2">13,5</td><td>-</td><td>-</td><td colspan="2">0,5</td><td colspan="2">12</td><td colspan="2">0,5</td><td></td></tr>
<tr><td>8</td><td colspan="2">12 квалитет</td><td>ние</td><td>15</td><td colspan="2">0,37</td><td colspan="2">10</td><td>-</td><td>-</td><td colspan="2">0,6</td><td colspan="2"></td><td colspan="2">0,6</td><td></td></tr>
<tr><td>9</td><td></td><td></td><td>прямоу-</td><td>20</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">0,7</td><td colspan="2"></td><td colspan="2">0,7</td><td>16,8</td></tr>
<tr><td>10</td><td></td><td></td><td>гольных</td><td>25</td><td colspan="2">0,48</td><td colspan="2">7,5</td><td>-</td><td>-</td><td colspan="2">0,7</td><td colspan="2">10,7</td><td colspan="2">0,7</td><td></td></tr>
<tr><td>11</td><td></td><td></td><td>пазов</td><td>30</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">0,7</td><td colspan="2"></td><td colspan="2">0,7</td><td></td></tr>
<tr><td>12</td><td></td><td></td><td></td><td>50</td><td colspan="2">0,36</td><td colspan="2">9,5</td><td>-</td><td>-</td><td colspan="2">0,65</td><td colspan="2">12</td><td colspan="2">0,85</td><td></td></tr>
<tr><td colspan="18">Поправочные коэффициенты на скорость резания в зависимости от:</td></tr>
<tr><td colspan="6">Предела прочности Обрабатываемый материал или твердости Предел прочности,</td><td colspan="6">Сталь конструкционная</td><td colspan="6">Чугун серый</td></tr>
<tr><td colspan="6">обрабатываемого сигма , МПа материала в Твердость, НВ, МПа</td><td colspan="2">до 590</td><td colspan="4">590...740 св. 740</td><td colspan="2">до 1760</td><td colspan="2">1760...2150</td><td colspan="2">св. 2150</td></tr>
<tr><td colspan="6">Коэффициент К пп</td><td colspan="2">1,1</td><td colspan="4">1,0 0,8</td><td colspan="2">1,1</td><td colspan="2">1,0</td><td colspan="2">0,8</td></tr>
</table>







<a id="p101885"></a>

<table>
<colgroup><col width="4%"><col width="9%"><col width="5%"><col width="9%"><col width="10%"><col width="5%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="8%"><col width="2%"><col width="7%"><col width="10%"><col width="7%"></colgroup>
<tr><td colspan="9" rowspan="2">Режимы резания</td><td colspan="7">Поперечно-строгальные и долбежные станки</td></tr>
<tr><td colspan="7">Приложение 4</td></tr>
<tr><td colspan="16">1. Поперечно-строгальные станки</td></tr>
<tr><td rowspan="6">N позиции</td><td rowspan="6">Мощность станка, N, кВт</td><td colspan="2" rowspan="6">Шероховатость поверхности и точность</td><td rowspan="6">Вид обработки</td><td colspan="2" rowspan="6">Глубина резания, t, мм, до</td><td colspan="9">Обрабатываемый материал</td></tr>
<tr><td colspan="4">Сталь</td><td colspan="5">Чугун</td></tr>
<tr><td colspan="9">Режущий инструмент</td></tr>
<tr><td colspan="4">Резцы из стали Р6М5</td><td colspan="3">Резцы из стали Р6М5</td><td colspan="2">Резцы с пластинками ВК8, ВК6</td></tr>
<tr><td colspan="9">Режимы резания</td></tr>
<tr><td colspan="2">S, мм/дв. ход</td><td colspan="2">v, м/мин.</td><td colspan="2">S, мм/дв. ход</td><td>v, м/мин.</td><td>S, мм/дв. ход</td><td>v, м/мин.</td></tr>
<tr><td>1</td><td>3</td><td colspan="2">Rz 80;</td><td>Строгание</td><td colspan="2">3</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>1,0</td><td>29</td></tr>
<tr><td>2</td><td></td><td colspan="2" rowspan="2">14...12 квалитет</td><td>горизонтальных</td><td colspan="2">5</td><td colspan="2">0,6</td><td colspan="2">15</td><td colspan="2">-</td><td>-</td><td>0,8</td><td>28</td></tr>
<tr><td>3</td><td>5</td><td>поверх-</td><td colspan="2">3</td><td colspan="2">0,9</td><td colspan="2">21</td><td colspan="2">-</td><td>-</td><td>1,4</td><td></td></tr>
<tr><td>4</td><td></td><td colspan="2"></td><td>ностей</td><td colspan="2">5</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>1,1</td><td>26</td></tr>
<tr><td>5</td><td></td><td colspan="2" rowspan="2"></td><td rowspan="2"></td><td colspan="2">8</td><td colspan="2">0,6</td><td colspan="2">16,5</td><td colspan="2">-</td><td>-</td><td>0,8</td><td></td></tr>
<tr><td>6</td><td>8...10</td><td colspan="2">5</td><td colspan="2">1,0</td><td colspan="2">17</td><td colspan="2">-</td><td>-</td><td>1,5</td><td></td></tr>
<tr><td>7</td><td></td><td colspan="2"></td><td rowspan="2"></td><td colspan="2">8</td><td colspan="2">0,75</td><td colspan="2">15</td><td colspan="2">-</td><td>-</td><td>1,2</td><td>20</td></tr>
<tr><td>8</td><td>3...10</td><td colspan="2">Rz 40; 11 квалитет</td><td colspan="2">1 - 2</td><td colspan="2">0,6</td><td colspan="2">47</td><td colspan="2">-</td><td>-</td><td>0,8</td><td>40</td></tr>
<tr><td>9</td><td></td><td colspan="2">Rz 20; 11 квалитет</td><td></td><td colspan="2"></td><td colspan="2">0,45</td><td colspan="2">40</td><td colspan="2">-</td><td>-</td><td>0,6</td><td>48</td></tr>
<tr><td>10</td><td>3...5</td><td colspan="2">Rz 80;</td><td>Строгание</td><td colspan="2">5</td><td colspan="2"></td><td colspan="2">19</td><td colspan="2">-</td><td>-</td><td>0,4</td><td>38</td></tr>
<tr><td>11</td><td></td><td colspan="2" rowspan="2">14...12 квалитет</td><td>вертикальных</td><td colspan="2">8</td><td colspan="2">0,4</td><td colspan="2">16</td><td colspan="2">-</td><td>-</td><td>0,4</td><td>34</td></tr>
<tr><td>12</td><td>8...10</td><td>поверх-</td><td colspan="2">5</td><td colspan="2">0,7</td><td colspan="2">14</td><td colspan="2">-</td><td>-</td><td>1,0</td><td>24</td></tr>
<tr><td>13</td><td></td><td colspan="2"></td><td rowspan="2">ностей</td><td colspan="2">8</td><td colspan="2">0,6</td><td colspan="2"></td><td colspan="2">-</td><td>-</td><td>0,8</td><td></td></tr>
<tr><td>14</td><td>3...10</td><td colspan="2">Rz 40... Rz 20</td><td colspan="2">1</td><td colspan="2">0,35</td><td colspan="2">28</td><td colspan="2">-</td><td>-</td><td>0,35</td><td>37</td></tr>
<tr><td>15</td><td>-</td><td colspan="2">Rz 80</td><td>Строгание прямоугольных пазов</td><td colspan="2">-</td><td colspan="2">0,22</td><td colspan="2">12,5</td><td colspan="2">0,3 - 0,4</td><td>11 - 10</td><td>0,3 - 0,4</td><td>17,5 - 15,3</td></tr>
<tr><td colspan="16">2. Долбежные станки</td></tr>
<tr><td>16</td><td>-</td><td colspan="2">Rz 80</td><td>Обработка</td><td colspan="2">5</td><td colspan="2">0,7</td><td colspan="2">16</td><td colspan="2">1,3</td><td>10</td><td></td><td></td></tr>
<tr><td>17</td><td></td><td colspan="2"></td><td rowspan="2">плоскостей</td><td colspan="2">8</td><td colspan="2">0,5</td><td colspan="2"></td><td colspan="2">1,0</td><td></td><td></td><td></td></tr>
<tr><td>18</td><td>-</td><td colspan="2">Rz 40... Rz 20</td><td colspan="2">10</td><td colspan="2">0,35</td><td colspan="2">31</td><td colspan="2">0,6</td><td>18</td><td></td><td></td></tr>
<tr><td>19</td><td></td><td colspan="2">Rz 40...</td><td>Долбление</td><td colspan="2">5</td><td colspan="2">0,1</td><td colspan="2">12,6</td><td colspan="2">0,18</td><td>8</td><td></td><td></td></tr>
<tr><td>20</td><td></td><td colspan="2">Rz 20</td><td>пазов</td><td colspan="2">10</td><td colspan="2">0,12</td><td colspan="2">11</td><td colspan="2">0,22</td><td></td><td></td><td></td></tr>
<tr><td>21</td><td></td><td colspan="2"></td><td></td><td colspan="2">16</td><td colspan="2">0,14</td><td colspan="2">9,7</td><td colspan="2">0,26</td><td>7</td><td></td><td></td></tr>
<tr><td>22</td><td></td><td colspan="2"></td><td></td><td colspan="2">20</td><td colspan="2">0,18</td><td colspan="2">8,5</td><td colspan="2">0,30</td><td>6</td><td></td><td></td></tr>
<tr><td colspan="16">Поправочные коэффициенты на скорость резания в зависимости от:</td></tr>
<tr><td colspan="3">Предела прочности и твердости</td><td colspan="3">Обрабатываемый материал</td><td colspan="6">Сталь конструкционная</td><td colspan="4">Чугун серый</td></tr>
<tr><td colspan="3" rowspan="2">обрабатываемого материала</td><td colspan="3">Предел прочности, сигма , МПа в</td><td colspan="2">до 590</td><td colspan="2">590...740</td><td colspan="2">св. 740</td><td colspan="4">- - -</td></tr>
<tr><td colspan="3">Твердость, НВ, МПа</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2"></td><td colspan="4">до 1760 1760... св. 2150 2150</td></tr>
<tr><td colspan="3"></td><td colspan="3">Коэффициент К</td><td colspan="2">1,1</td><td colspan="2">1,0</td><td colspan="2">0,8</td><td colspan="4">1,1 1,0 0,8</td></tr>
</table>







<a id="p101920"></a>

<table>
<colgroup><col width="6%"><col width="18%"><col width="18%"><col width="17%"><col width="22%"><col width="5%"><col width="14%"></colgroup>
<tr><td colspan="4">Припуски на механическую обработку Детали типа валов и плоские Прокат и поковка</td><td colspan="2">Приложение 5</td><td>лист 1</td></tr>
<tr><td colspan="7">1. Прокат</td></tr>
<tr><td rowspan="2">N позиции</td><td rowspan="2">Характер заготовки</td><td colspan="2">Окончательный размер обработки, мм, до</td><td colspan="3">Припуск, мм</td></tr>
<tr><td>По диаметру или ширине</td><td>По длине</td><td>По диаметру или ширине "а"</td><td colspan="2">По длине "В"</td></tr>
<tr><td>1</td><td>Круглое</td><td>30</td><td>100</td><td>5</td><td colspan="2">5</td></tr>
<tr><td>2</td><td>сечение</td><td></td><td>&gt; 100</td><td>6</td><td colspan="2">5</td></tr>
<tr><td>3</td><td></td><td></td><td>100</td><td>5</td><td colspan="2">5</td></tr>
<tr><td>4</td><td></td><td>50</td><td>&gt; 100</td><td>6</td><td colspan="2">5</td></tr>
<tr><td>5</td><td></td><td></td><td>250</td><td>7</td><td colspan="2">6</td></tr>
<tr><td>6</td><td></td><td>80</td><td>&gt; 250</td><td>8</td><td colspan="2">7</td></tr>
<tr><td>7</td><td></td><td></td><td>250</td><td>8</td><td colspan="2">7</td></tr>
<tr><td>8</td><td></td><td>&gt; 80</td><td>&gt; 250</td><td>9</td><td colspan="2">7</td></tr>
<tr><td>9</td><td>Прямоуголь-</td><td></td><td>250</td><td>5</td><td colspan="2">6</td></tr>
<tr><td>10</td><td>ное сечение</td><td>50</td><td>&gt; 250</td><td>6</td><td colspan="2">7</td></tr>
<tr><td>11</td><td></td><td></td><td>&lt;= 250</td><td>5</td><td colspan="2">6</td></tr>
<tr><td>12</td><td></td><td>80</td><td>&gt; 250</td><td>6</td><td colspan="2">7</td></tr>
<tr><td>13</td><td></td><td></td><td>&lt;= 250</td><td>6</td><td colspan="2">7</td></tr>
<tr><td>14</td><td></td><td>120</td><td>&gt; 250</td><td>6</td><td colspan="2">9</td></tr>
<tr><td>15</td><td></td><td></td><td>&lt;= 250</td><td>6</td><td colspan="2">7</td></tr>
<tr><td>16</td><td></td><td>&gt; 120</td><td>&gt; 250</td><td>6</td><td colspan="2">9</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="13%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="3%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="9">Припуски на механическую обработку Детали типа валов и плоские</td><td colspan="7">Приложение 5 лист 2</td></tr>
<tr><td colspan="16">II. Поковки Прямоугольное и круглое сечение</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина детали,</td><td>Припуск</td><td colspan="13">Диаметр детали, D, или размер сечения, В, Н, мм</td></tr>
<tr><td rowspan="2">L, мм</td><td rowspan="2">по диаметру или ширине - а, по длине - В, мм</td><td>до 50</td><td>св. 50 до 70</td><td>св. 70 до 90</td><td>св. 90 до 120</td><td>св. 120 до 160</td><td colspan="2">св. 160 до 200</td><td>св. 200 до 250</td><td>св. 250 до 300</td><td>св. 300 до 360</td><td>св. 360 до 500</td><td>св. 500 до 650</td><td>св. 650 до 800</td></tr>
<tr><td colspan="13">Припуск, мм</td></tr>
<tr><td>17</td><td></td><td>а</td><td>5</td><td>6</td><td>7</td><td>8</td><td>9</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td>до 250</td><td>В</td><td>13</td><td>15</td><td>18</td><td>20</td><td>23</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td>св. 250</td><td>а</td><td>6</td><td>7</td><td>8</td><td>9</td><td>10</td><td colspan="2">11</td><td>12</td><td>13</td><td>14</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>до 500</td><td>В</td><td>15</td><td>18</td><td>20</td><td>23</td><td>25</td><td colspan="2">28</td><td>30</td><td>33</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>21</td><td>св. 500</td><td>а</td><td>7</td><td>8</td><td>9</td><td>10</td><td>11</td><td colspan="2">12</td><td>13</td><td>14</td><td>15</td><td>16</td><td>-</td><td>-</td></tr>
<tr><td>22</td><td>до 800</td><td>В</td><td>18</td><td>20</td><td>23</td><td>25</td><td>28</td><td colspan="2">30</td><td>33</td><td>35</td><td>38</td><td>40</td><td>-</td><td>-</td></tr>
<tr><td>23</td><td>св. 800</td><td>а</td><td>8</td><td>9</td><td>10</td><td>11</td><td>12</td><td colspan="2">13</td><td>14</td><td>15</td><td>16</td><td>17</td><td>18</td><td>19</td></tr>
<tr><td>24</td><td>до 1200</td><td>В</td><td>20</td><td>23</td><td>25</td><td>28</td><td>30</td><td colspan="2">33</td><td>35</td><td>38</td><td>40</td><td>43</td><td>45</td><td>48</td></tr>
<tr><td>25</td><td>св. 1200</td><td>а</td><td>-</td><td>10</td><td>11</td><td>12</td><td>13</td><td colspan="2">14</td><td>15</td><td>16</td><td>17</td><td>18</td><td>19</td><td>20</td></tr>
<tr><td>26</td><td>до 1700</td><td>В</td><td>-</td><td>25</td><td>28</td><td>30</td><td>33</td><td colspan="2">35</td><td>38</td><td>40</td><td>43</td><td>45</td><td>48</td><td>50</td></tr>
<tr><td>27</td><td>св. 1700</td><td>а</td><td>-</td><td>11</td><td>12</td><td>13</td><td>14</td><td colspan="2">15</td><td>16</td><td>17</td><td>18</td><td>19</td><td>20</td><td>21</td></tr>
<tr><td>28</td><td>до 2300</td><td>В</td><td>-</td><td>28</td><td>30</td><td>33</td><td>35</td><td colspan="2">38</td><td>40</td><td>43</td><td>45</td><td>48</td><td>50</td><td>53</td></tr>
<tr><td>29</td><td>св. 2300</td><td>а</td><td>-</td><td>-</td><td>13</td><td>14</td><td>15</td><td colspan="2">16</td><td>17</td><td>18</td><td>19</td><td>20</td><td>21</td><td>22</td></tr>
<tr><td>30</td><td>до 3000</td><td>В</td><td>-</td><td>-</td><td>33</td><td>35</td><td>38</td><td colspan="2">40</td><td>43</td><td>45</td><td>48</td><td>50</td><td>53</td><td>55</td></tr>
<tr><td>31</td><td>св. 3000</td><td>а</td><td>-</td><td>-</td><td>-</td><td>15</td><td>16</td><td colspan="2">17</td><td>18</td><td>19</td><td>20</td><td>21</td><td>22</td><td>23</td></tr>
<tr><td>32</td><td>до 4000</td><td>В</td><td>-</td><td>-</td><td>-</td><td>38</td><td>40</td><td colspan="2">43</td><td>45</td><td>48</td><td>50</td><td>53</td><td>55</td><td>58</td></tr>
</table>


<a id="p101958"></a>Примечание:
<a id="p101959"></a>Для заготовки прямоугольного сечения припуск на обработку следует назначать по наибольшему размеру стороны заготовки.


<table>
<colgroup><col width="6%"><col width="15%"><col width="25%"><col width="15%"><col width="20%"><col width="5%"><col width="14%"></colgroup>
<tr><td colspan="6">Припуски на механическую обработку Приложение 5 Детали типа шайб, фланцев, кубиков</td><td>лист 3</td></tr>
<tr><td rowspan="2">N позиции</td><td rowspan="2">Высота детали, Н, мм</td><td>Диаметр детали, D, или размер</td><td colspan="4">Припуск, мм</td></tr>
<tr><td>А, В, мм</td><td>за высоту (h)</td><td>на диаметр или размер А, В (d)</td><td colspan="2">на диаметр отверстия (С)</td></tr>
<tr><td>33</td><td>до 50</td><td>до 180</td><td>8</td><td>11</td><td colspan="2">15</td></tr>
<tr><td>34</td><td></td><td>181 - 250</td><td>9</td><td>12</td><td colspan="2">16</td></tr>
<tr><td>35</td><td></td><td>до 180</td><td>8</td><td>11</td><td colspan="2">16</td></tr>
<tr><td>36</td><td>51 - 80</td><td>181 - 250</td><td>9</td><td>12</td><td colspan="2">17</td></tr>
<tr><td>37</td><td></td><td>251 - 360</td><td>11</td><td>14</td><td colspan="2">20</td></tr>
<tr><td>38</td><td></td><td>до 180</td><td>11</td><td>12</td><td colspan="2">17</td></tr>
<tr><td>39</td><td>81 - 120</td><td>181 - 250</td><td>12</td><td>14</td><td colspan="2">19</td></tr>
<tr><td>40</td><td></td><td>251 - 360</td><td>13</td><td>16</td><td colspan="2">22</td></tr>
<tr><td>41</td><td></td><td>до 180</td><td>13</td><td>13</td><td colspan="2">18</td></tr>
<tr><td>42</td><td>121 - 180</td><td>181 - 250</td><td>14</td><td>16</td><td colspan="2">21</td></tr>
<tr><td>43</td><td></td><td>251 - 360</td><td>15</td><td>18</td><td colspan="2">24</td></tr>
<tr><td>44</td><td></td><td>361 - 500</td><td>15</td><td>20</td><td colspan="2">26</td></tr>
<tr><td>45</td><td></td><td>до 250</td><td>17</td><td>17</td><td colspan="2">22</td></tr>
<tr><td>46</td><td>181 - 250</td><td>251 - 360</td><td>18</td><td>18</td><td colspan="2">25</td></tr>
<tr><td>47</td><td></td><td>361 - 500</td><td>18</td><td>21</td><td colspan="2">27</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="13%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="9">Припуски на механическую обработку Отливки из серого чугуна и стали</td><td colspan="6">Приложение 5 лист 4</td></tr>
<tr><td colspan="15">Отливки</td></tr>
<tr><td rowspan="4">N позиции</td><td>Наибольший</td><td rowspan="4">Положение поверхности при заливке</td><td colspan="6">Чугун серый</td><td colspan="6">Сталь</td></tr>
<tr><td rowspan="3">габаритный размер детали, мм</td><td colspan="12">Номинальный размер, мм</td></tr>
<tr><td>до 120</td><td>св. 120 до 260</td><td>св. 260 до 500</td><td>св. 500 до 800</td><td>св. 800 до 1250</td><td>св. 1250 до 2000</td><td>до 120</td><td>св. 120 до 260</td><td>св. 260 до 500</td><td>св. 500 до 800</td><td>св. 800 до 1250</td><td>св. 1250 до 2000</td></tr>
<tr><td colspan="12">Припуск, мм</td></tr>
<tr><td>48</td><td></td><td>Верх</td><td>4,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>49</td><td>до 120</td><td>Низ, бок</td><td>3,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>4</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>50</td><td>св. 120</td><td>Верх</td><td>5</td><td>5,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>5</td><td>6</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>51</td><td>до 260</td><td>Низ, бок</td><td>4</td><td>4,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>4</td><td>5</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>52</td><td>св. 260</td><td>Верх</td><td>6</td><td>7</td><td>7</td><td>-</td><td>-</td><td>-</td><td>6</td><td>8</td><td>9</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>53</td><td>до 500</td><td>Низ, бок</td><td>4,5</td><td>5</td><td>6</td><td>-</td><td>-</td><td>-</td><td>5</td><td>6</td><td>6</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>54</td><td>св. 500</td><td>Верх</td><td>7</td><td>7</td><td>8</td><td>9</td><td>-</td><td>-</td><td>7</td><td>8</td><td>10</td><td>11</td><td>-</td><td>-</td></tr>
<tr><td>55</td><td>до 800</td><td>Низ, бок</td><td>5</td><td>5</td><td>6</td><td>7</td><td>-</td><td>-</td><td>5</td><td>6</td><td>7</td><td>7</td><td>-</td><td>-</td></tr>
<tr><td>56</td><td>св. 800</td><td>Верх</td><td>7</td><td>8</td><td>8</td><td>9</td><td>10</td><td>-</td><td>9</td><td>10</td><td>11</td><td>12</td><td>13</td><td>-</td></tr>
<tr><td>57</td><td>до 1250</td><td>Низ, бок</td><td>5,5</td><td>6</td><td>6</td><td>7</td><td>7,5</td><td>-</td><td>6</td><td>7</td><td>8</td><td>8</td><td>9</td><td>-</td></tr>
<tr><td>58</td><td>св. 1250</td><td>Верх</td><td>8</td><td>8</td><td>9</td><td>9</td><td>10</td><td>12</td><td>10</td><td>11</td><td>12</td><td>13</td><td>14</td><td>16</td></tr>
<tr><td>59</td><td>до 2000</td><td>Низ, бок</td><td>6</td><td>6</td><td>7</td><td>7</td><td>8</td><td>9</td><td>7</td><td>8</td><td>9</td><td>9</td><td>10</td><td>11</td></tr>
<tr><td>60</td><td>св. 2000</td><td>Верх</td><td>9</td><td>9</td><td>10</td><td>10</td><td>11</td><td>12</td><td>10</td><td>11</td><td>13</td><td>14</td><td>15</td><td>16</td></tr>
<tr><td>61</td><td>до 3150</td><td>Низ, бок</td><td>7</td><td>7</td><td>8</td><td>8</td><td>9</td><td>9</td><td>8</td><td>9</td><td>10</td><td>10</td><td>11</td><td>12</td></tr>
<tr><td>62</td><td>св. 3150</td><td>Верх</td><td>9</td><td>10</td><td>10</td><td>11</td><td>12</td><td>14</td><td>12</td><td>13</td><td>14</td><td>15</td><td>16</td><td>17</td></tr>
<tr><td>63</td><td>до 5000</td><td>Низ, бок</td><td>7</td><td>8</td><td>8</td><td>9</td><td>9</td><td>11</td><td>9</td><td>10</td><td>11</td><td>11</td><td>12</td><td>13</td></tr>
</table>







<a id="p101997"></a>

<table>
<colgroup><col width="6%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="4%"><col width="4%"><col width="3%"><col width="6%"><col width="6%"><col width="3%"><col width="3%"><col width="6%"><col width="6%"><col width="3%"><col width="3%"><col width="6%"><col width="9%"></colgroup>
<tr><td colspan="11">Теоретическая масса заготовки</td><td colspan="8">Приложение 6 лист 1</td></tr>
<tr><td colspan="19">1. Заготовка цилиндрическая</td></tr>
<tr><td colspan="6">Диаметр заготовки, D, мм</td><td colspan="2">10</td><td colspan="2">12</td><td colspan="2">16</td><td colspan="2">20</td><td colspan="2">25</td><td colspan="2">32</td><td>40</td></tr>
<tr><td colspan="6">Теоретическая масса на длину 1 м, кг</td><td colspan="2">0,617</td><td colspan="2">0,888</td><td colspan="2">1,58</td><td colspan="2">2,47</td><td colspan="2">3,85</td><td colspan="2">6,32</td><td>9,87</td></tr>
<tr><td colspan="6">Диаметр заготовки, D, мм</td><td colspan="2">100</td><td colspan="2">120</td><td colspan="2">160</td><td colspan="2">200</td><td colspan="2">250</td><td colspan="2">320</td><td>400</td></tr>
<tr><td colspan="6">Теоретическая масса на длину 1 м, кг</td><td colspan="2">61,7</td><td colspan="2">88,8</td><td colspan="2">158,0</td><td colspan="2">247,0</td><td colspan="2">385,0</td><td colspan="2">632,0</td><td>987,0</td></tr>
<tr><td colspan="19">2. Заготовка прямоугольная</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Ширина заготовки, В, мм</td><td colspan="17">Высота заготовки, Н, мм</td></tr>
<tr><td>40</td><td>50</td><td>60</td><td colspan="2">80</td><td colspan="2">100</td><td>120</td><td>140</td><td colspan="2">160</td><td>200</td><td>220</td><td colspan="2">250</td><td colspan="2">320 400</td></tr>
<tr><td colspan="17">Теоретическая масса на длину 1 м, кг</td></tr>
<tr><td>1</td><td>50</td><td>15,7</td><td>19,6</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">- -</td></tr>
<tr><td>2</td><td>60</td><td>18,8</td><td>23,6</td><td>28,3</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">- -</td></tr>
<tr><td>3</td><td>80</td><td>25,1</td><td>31,4</td><td>37,7</td><td colspan="2">50,2</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">- -</td></tr>
<tr><td>4</td><td>100</td><td>31,4</td><td>39,3</td><td>47,1</td><td colspan="2">62,8</td><td colspan="2">78,5</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">- -</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="9">Теоретическая масса заготовки</td><td colspan="6">Приложение 6 лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Ширина заготовки, В, мм</td><td colspan="13">Высота заготовки, Н, мм</td></tr>
<tr><td>40</td><td>50</td><td>60</td><td>80</td><td>100</td><td>120</td><td>140</td><td>160</td><td>200</td><td>220</td><td>250</td><td>320</td><td>400</td></tr>
<tr><td colspan="13">Теоретическая масса на длину l м, кг</td></tr>
<tr><td>5</td><td>120</td><td>37,7</td><td>47,1</td><td>56,5</td><td>75,4</td><td>94,2</td><td>113</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>140</td><td>44,0</td><td>55,0</td><td>65,9</td><td>87,9</td><td>110</td><td>132</td><td>154</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>160</td><td>50,2</td><td>62,8</td><td>75,4</td><td>100</td><td>126</td><td>151</td><td>176</td><td>201</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>180</td><td>56,5</td><td>70,7</td><td>84,8</td><td>113</td><td>141</td><td>170</td><td>198</td><td>226</td><td>282</td><td>310</td><td>354</td><td>452</td><td>565</td></tr>
<tr><td>9</td><td>200</td><td>62,8</td><td>78,5</td><td>94,2</td><td>126</td><td>157</td><td>188</td><td>220</td><td>251</td><td>314</td><td>346</td><td>392</td><td>502</td><td>628</td></tr>
<tr><td>10</td><td>220</td><td>69,1</td><td>86,4</td><td>104</td><td>138</td><td>173</td><td>207</td><td>242</td><td>276</td><td>346</td><td>380</td><td>432</td><td>553</td><td>691</td></tr>
<tr><td>11</td><td>250</td><td>78,5</td><td>98,1</td><td>118</td><td>157</td><td>196</td><td>236</td><td>275</td><td>314</td><td>392</td><td>432</td><td>490</td><td>628</td><td>785</td></tr>
<tr><td>12</td><td>280</td><td>87,9</td><td>110</td><td>132</td><td>176</td><td>220</td><td>264</td><td>308</td><td>352</td><td>440</td><td>484</td><td>550</td><td>703</td><td>879</td></tr>
<tr><td>13</td><td>320</td><td>100</td><td>126</td><td>151</td><td>201</td><td>251</td><td>301</td><td>352</td><td>402</td><td>502</td><td>553</td><td>628</td><td>804</td><td>1005</td></tr>
<tr><td>14</td><td>360</td><td>-</td><td>-</td><td>-</td><td>226</td><td>283</td><td>339</td><td>396</td><td>452</td><td>565</td><td>622</td><td>706</td><td>904</td><td>1130</td></tr>
<tr><td>15</td><td>400</td><td>-</td><td>-</td><td>-</td><td>251</td><td>314</td><td>377</td><td>440</td><td>502</td><td>628</td><td>691</td><td>785</td><td>1005</td><td>1256</td></tr>
<tr><td>16</td><td>450</td><td>-</td><td>-</td><td>-</td><td>283</td><td>353</td><td>424</td><td>495</td><td>565</td><td>707</td><td>777</td><td>883</td><td>1130</td><td>1413</td></tr>
</table>







<a id="p102023"></a>

<table>
<colgroup><col width="37%"><col width="15%"><col width="37%"><col width="11%"></colgroup>
<tr><td colspan="2">Группы материалов по обрабатываемости</td><td colspan="2">Приложение 7</td></tr>
<tr><td>Обрабатываемый материал</td><td colspan="2">Марки материалов</td><td>Группа</td></tr>
<tr><td>Стали конструкционные</td><td colspan="2">20, 40, 45, 50Г, 65Г, 15Х, 40Х,</td><td>I</td></tr>
<tr><td>углеродистые и</td><td colspan="2">40М, 12ХНЗА, 12Х2Н4А, 20ХНЗА,</td><td></td></tr>
<tr><td>легированные хромом, марганцем, никелем и инструментальные углеродистые</td><td colspan="2">20ХГНР, У7А, У8А, У10А, У12А и другие близкие к ним</td><td></td></tr>
<tr><td>Стали конструкционные,</td><td colspan="2">33ХСА, 33ХМЮА, 30ХГС, 12ХНВА,</td><td>II</td></tr>
<tr><td>легированные вольфра-</td><td colspan="2">30ХГТ, 38ХСА, 18ХГТ, 12ХМФ, 20ХМ,</td><td></td></tr>
<tr><td>мом, титаном, кремнием,</td><td colspan="2">30ХМ, 34ХН1М, 40ХМВА, 34ХНЗМФ,</td><td></td></tr>
<tr><td>молибденом</td><td colspan="2">15Х1М1Ф, ХВГ, 5СХФА, ШХ-15 и другие близкие к ним</td><td></td></tr>
<tr><td>Стали жаропрочные и</td><td colspan="2">1Х12В2МФ, 15Х12ВМФ, 15МФКР,</td><td>III</td></tr>
<tr><td>нержавеющие типа</td><td colspan="2">20Х13, 30Х13, 40Х13, 14Х17В2, 20Х23Н13, 20Х23Н18, 20Х25Н20С2, Х20Н80, 30Х14А, Х15Н60, 45Х17МФ6 и другие близкие к ним</td><td></td></tr>
<tr><td>Стали жаропрочные и</td><td colspan="2">12Х18Н9Т, 12Х18Н10Т, 10Х11Н203Р,</td><td>IV</td></tr>
<tr><td>нержавеющие (содержащие титан), быстрорежущие инструментальные стали типа</td><td colspan="2">4Х12НВГ8МФВ, Р18, Р9, Р6М3 и другие близкие к ним</td><td></td></tr>
<tr><td>Чугуны и бронзы</td><td colspan="2">Чугуны: СЧ10, СЧ15, СЧ20, СЧ25, СЧ30, СЧ35 Бронзы: ОЦ10-2, ОЦСБ-6-3, АЖ9-4 и другие близкие к ним</td><td>V</td></tr>
</table>







<a id="p102030"></a>

<table>
<colgroup><col width="5%"><col width="11%"><col width="7%"><col width="11%"><col width="9%"><col width="14%"><col width="8%"><col width="9%"><col width="9%"><col width="5%"><col width="11%"></colgroup>
<tr><td colspan="7">Механические свойства основных конструкционных углеродистых и легированных сталей</td><td colspan="3">Приложение 8</td><td>лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Группа стали</td><td rowspan="3">Марка</td><td colspan="8">Механические свойства</td></tr>
<tr><td colspan="3">В состоянии поставки по ГОСТу</td><td colspan="5">После термической обработки</td></tr>
<tr><td>ГОСТ</td><td>Состояние</td><td>сигма , в НВ, МПа</td><td colspan="2">Типовая термическая обработка</td><td>МПа</td><td colspan="2">НВ, МПа</td></tr>
<tr><td>1</td><td>Углеродистая обыкно-</td><td>Ст.0</td><td>380-71</td><td>Г*</td><td>сигма = в 310</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>2</td><td>венного</td><td>Ст.1</td><td></td><td></td><td>310...390</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>3</td><td>качест-</td><td>Ст.2</td><td></td><td></td><td>330...410</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>4</td><td>ва</td><td>Ст.3</td><td></td><td></td><td>370...460</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>5</td><td></td><td>Ст.4</td><td></td><td></td><td>410...500</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>6</td><td></td><td>Ст.5</td><td></td><td></td><td>490...600</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>7</td><td></td><td>Ст.6</td><td></td><td></td><td>590...710</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>8</td><td></td><td>Ст.7</td><td></td><td></td><td>690...740</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>9</td><td></td><td>08</td><td>1050-74</td><td>Г</td><td>НВ &lt;= 1280</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>10</td><td></td><td></td><td>1050-74</td><td>Г</td><td>1340</td><td colspan="2"></td><td></td><td colspan="2"></td></tr>
<tr><td>11</td><td></td><td>10</td><td></td><td>Н</td><td>1830</td><td colspan="2">Нормализация</td><td>&lt; 330</td><td colspan="2">&gt;= 1400</td></tr>
<tr><td>12</td><td></td><td></td><td>1051-73</td><td>О</td><td>1400</td><td colspan="2">910°...930°</td><td></td><td colspan="2"></td></tr>
<tr><td>13</td><td></td><td></td><td>1050-74</td><td>Г</td><td>1400</td><td colspan="2">Нормализация</td><td></td><td colspan="2"></td></tr>
<tr><td>14</td><td></td><td>15</td><td></td><td>Н</td><td>1930</td><td colspan="2">910°...930°</td><td>&gt;= 360</td><td colspan="2">&lt;= 1530</td></tr>
<tr><td>15</td><td></td><td></td><td>1051-73</td><td>О</td><td>1460</td><td colspan="2"></td><td></td><td colspan="2"></td></tr>
<tr><td>16</td><td></td><td></td><td>1050-74</td><td>Г</td><td>1530</td><td colspan="2"></td><td></td><td colspan="2"></td></tr>
<tr><td>17</td><td></td><td>20</td><td>1051-73</td><td>Н</td><td>2030</td><td colspan="2">Нормализация</td><td>&gt;= 400</td><td colspan="2">1340...1710</td></tr>
<tr><td>18</td><td></td><td></td><td></td><td>О</td><td>1600</td><td colspan="2">900°...920°</td><td></td><td colspan="2"></td></tr>
<tr><td>19</td><td></td><td></td><td>1050-74</td><td>Б</td><td>1670</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>20</td><td></td><td>25</td><td>1051-73</td><td>Н</td><td>2130</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>21</td><td>Углеро-</td><td></td><td></td><td>О</td><td>1670</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>22</td><td>дистая</td><td></td><td>1050-74</td><td>Г</td><td>1750</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>23</td><td>качест-</td><td>30</td><td></td><td>Н</td><td>2240</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>24</td><td>венная</td><td></td><td>1051-73</td><td>О</td><td>1750</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>25</td><td></td><td>35</td><td>1050-74</td><td>Г</td><td>1830</td><td colspan="2">Нормализация</td><td>&gt;= 510</td><td colspan="2">1530...1920</td></tr>
<tr><td>26</td><td></td><td></td><td>1051-73</td><td>Н</td><td>2240</td><td colspan="2">860°...880° Закалка 880° Отпуск 600°</td><td></td><td colspan="2">1830</td></tr>
<tr><td>27</td><td></td><td>35</td><td></td><td>О</td><td>1830</td><td colspan="2"></td><td></td><td colspan="2"></td></tr>
<tr><td>28</td><td></td><td></td><td></td><td>Г</td><td>2130</td><td colspan="2">Нормализация</td><td></td><td colspan="2"></td></tr>
<tr><td>2</td><td></td><td>40</td><td>1050-73</td><td>О Н</td><td>1830 2360</td><td colspan="2">860°...880°</td><td>&gt;= 560</td><td colspan="2">1530...2030</td></tr>
<tr><td>29</td><td></td><td></td><td>1051-73</td><td>О</td><td>1930</td><td colspan="2">Отпуск 550°...620°</td><td>&gt;= 690</td><td colspan="2">1880...2230</td></tr>
<tr><td>30</td><td></td><td></td><td></td><td>Г</td><td>2360</td><td colspan="2">Нормализация</td><td></td><td colspan="2"></td></tr>
<tr><td>31</td><td></td><td>45</td><td>1050-74</td><td>О</td><td>1930</td><td colspan="2">850°...870°</td><td></td><td colspan="2"></td></tr>
<tr><td>32</td><td></td><td></td><td></td><td>Н</td><td>2360</td><td colspan="2">или</td><td>&gt;= 590</td><td colspan="2">1670...2130</td></tr>
<tr><td>33</td><td></td><td></td><td>1051-73</td><td></td><td>НВ &lt;= 2030</td><td colspan="2">Отжиг 840°...860°</td><td></td><td colspan="2"></td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="7%"><col width="11%"><col width="9%"><col width="13%"><col width="8%"><col width="9%"><col width="11%"><col width="4%"><col width="12%"></colgroup>
<tr><td colspan="7">Механические свойства основных конструкционных углеродистых и легированных сталей</td><td colspan="3">Приложение 8</td><td>лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Группа стали</td><td rowspan="3">Марка</td><td colspan="8">Механические свойства</td></tr>
<tr><td colspan="3">В состоянии поставки по ГОСТу</td><td colspan="5">После термической обработки</td></tr>
<tr><td>ГОСТ</td><td>Состояние</td><td>сигма , в МПа или НВ, МПа</td><td colspan="2">Типовая термическая обработка</td><td>сигма , в МПа</td><td colspan="2">НВ, МПа</td></tr>
<tr><td>34</td><td>Углеро-</td><td></td><td></td><td>Г</td><td>2360</td><td colspan="2">Нормализация</td><td></td><td colspan="2"></td></tr>
<tr><td>35</td><td>дистая</td><td>50</td><td>1050-74</td><td>О</td><td>2030</td><td colspan="2">840°...860°</td><td>&gt; 630</td><td colspan="2">1750...2240</td></tr>
<tr><td>36</td><td>качест-</td><td></td><td></td><td>Н</td><td>2500</td><td colspan="2">Закалка 840°</td><td></td><td colspan="2"></td></tr>
<tr><td>37</td><td>венная</td><td></td><td>1051-73</td><td>О</td><td>2150</td><td colspan="2">Отпуск 600°</td><td>-</td><td colspan="2">2130</td></tr>
<tr><td>38</td><td>с повы-</td><td></td><td></td><td>Г</td><td>2500</td><td colspan="2">Нормализация</td><td></td><td colspan="2"></td></tr>
<tr><td>39</td><td>шенным</td><td>55</td><td>1050-74</td><td>О</td><td>2130</td><td colspan="2">810°</td><td>680</td><td colspan="2">2240</td></tr>
<tr><td>40</td><td>содер-</td><td></td><td>1050-74</td><td>Г</td><td>2500</td><td colspan="2"></td><td></td><td colspan="2"></td></tr>
<tr><td>41</td><td>жанием</td><td>60</td><td></td><td>О</td><td>2240</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>42</td><td>марган-</td><td></td><td>1051-73</td><td>О</td><td>2240</td><td colspan="2"></td><td></td><td colspan="2"></td></tr>
<tr><td>43</td><td>ца</td><td></td><td></td><td>Г</td><td>2210</td><td colspan="2"></td><td></td><td colspan="2"></td></tr>
<tr><td>44</td><td></td><td>65</td><td>1050-74</td><td>О</td><td>2240</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>45</td><td></td><td></td><td>1050-74</td><td>Г</td><td>1600</td><td colspan="2">Нормализация</td><td></td><td colspan="2"></td></tr>
<tr><td>46</td><td></td><td>15Г</td><td></td><td>Н</td><td>2030</td><td colspan="2">920°</td><td>390</td><td colspan="2">&lt;= 1600</td></tr>
<tr><td>47</td><td></td><td></td><td>1051-73</td><td>О</td><td>1600</td><td colspan="2"></td><td></td><td colspan="2"></td></tr>
<tr><td>48</td><td></td><td>20Г</td><td>1050-74</td><td>Г</td><td>1930</td><td colspan="2">Нормализация 900°</td><td>420</td><td colspan="2">&lt;= 1930</td></tr>
<tr><td>49</td><td></td><td></td><td></td><td>Г</td><td>2130</td><td colspan="2">Нормализация</td><td>540</td><td colspan="2">1830</td></tr>
<tr><td>50</td><td></td><td>30Г</td><td>1050-74</td><td>О</td><td>1830</td><td colspan="2">880°</td><td></td><td colspan="2"></td></tr>
<tr><td>51</td><td></td><td></td><td></td><td>Г</td><td>2240</td><td colspan="2">Нормализация</td><td></td><td colspan="2">&lt;= 2240</td></tr>
<tr><td>52</td><td></td><td>40Г</td><td>1050-74</td><td>О</td><td>2030</td><td colspan="2">860°</td><td>590</td><td colspan="2">&lt;= 2050</td></tr>
<tr><td>53</td><td></td><td></td><td></td><td>Г</td><td>2500</td><td colspan="2">Нормализация</td><td></td><td colspan="2"></td></tr>
<tr><td>54</td><td></td><td></td><td>1050-74</td><td>О</td><td>2130</td><td colspan="2">840°</td><td></td><td colspan="2"></td></tr>
<tr><td>55</td><td></td><td>50Г</td><td></td><td>Н</td><td>2640</td><td colspan="2">Закалка 800°</td><td>640</td><td colspan="2">2240</td></tr>
<tr><td>56</td><td></td><td></td><td>1051-73</td><td>О</td><td>2240</td><td colspan="2">Отпуск 600°</td><td></td><td colspan="2"></td></tr>
<tr><td>57</td><td></td><td></td><td></td><td>Г</td><td>2640</td><td colspan="2">Отжиг 800°...830°</td><td>-</td><td colspan="2">1920...2240</td></tr>
<tr><td>58</td><td rowspan="2"></td><td rowspan="2">60Г</td><td rowspan="2">1050-74</td><td>О</td><td>2240</td><td colspan="2">Нормализация 840°</td><td>&gt;= 690</td><td colspan="2">&lt;= 2240</td></tr>
<tr><td>59</td><td>Г</td><td>2790</td><td colspan="2">Отжиг 790°...810°</td><td>40</td><td colspan="2">1920...2240</td></tr>
<tr><td>60</td><td></td><td>65Г</td><td>1050-74</td><td>О</td><td>2240</td><td colspan="2">Нормализация</td><td>&lt;= 740</td><td colspan="2">&lt;= 2360</td></tr>
<tr><td>61</td><td></td><td></td><td></td><td>Г</td><td>2790</td><td colspan="2">Отжиг 790°...810°</td><td>-</td><td colspan="2">1980...2300</td></tr>
<tr><td>62</td><td></td><td>70Г</td><td>1050-74</td><td>О</td><td>2240</td><td colspan="2">Нормализация</td><td>&gt;= 790</td><td colspan="2">&lt;= 2360</td></tr>
<tr><td>63</td><td>Автоматная</td><td>А12</td><td></td><td>X</td><td>1640... 2130</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>64</td><td></td><td>А20</td><td></td><td>X</td><td>1640... 2140</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>65</td><td></td><td>А30</td><td>1414-75</td><td>X</td><td>1710... 2190</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>66</td><td></td><td>А40Г</td><td></td><td>X</td><td>1670... 2240</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="9%"><col width="10%"><col width="9%"><col width="13%"><col width="8%"><col width="9%"><col width="10%"><col width="4%"><col width="12%"></colgroup>
<tr><td colspan="7">Механические свойства основных конструкционных углеродистых и легированных сталей</td><td colspan="3">Приложение 8</td><td>лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Группа стали</td><td rowspan="3">Марка</td><td colspan="8">Механические свойства</td></tr>
<tr><td colspan="3">В состоянии поставки по ГОСТу</td><td colspan="5">После термической обработки</td></tr>
<tr><td>ГОСТ</td><td>Состояние</td><td>сигма , в МПа или НВ, МПа</td><td colspan="2">Типовая термическая обработка</td><td>сигма , в МПа</td><td colspan="2">НВ, МПа</td></tr>
<tr><td>67</td><td>Хромистая</td><td>15Х</td><td>4543-71</td><td>ОП</td><td>1750</td><td colspan="2">Нормализация 890°...910°</td><td>690</td><td colspan="2">1400...1750</td></tr>
<tr><td>68</td><td></td><td>20Х</td><td>4543-71</td><td>ОП</td><td>1750</td><td colspan="2">Нормализация 890°...910°</td><td>790</td><td colspan="2">1430...2030</td></tr>
<tr><td>69</td><td></td><td>30Х</td><td>4543-71</td><td>ОП</td><td>1830</td><td colspan="2">Закалка 860° Отпуск 500°</td><td>890</td><td colspan="2">1820</td></tr>
<tr><td>70</td><td></td><td>35Х</td><td>4543-71</td><td>ОП</td><td>1930</td><td colspan="2">Закалка 860° Отпуск 500° Отжиг 880°...900°</td><td>930</td><td colspan="2">&lt;= 1930</td></tr>
<tr><td>71</td><td></td><td>38ХА</td><td>4543-71</td><td>ОП</td><td>2030</td><td colspan="2">Закалка 860° Отпуск 550°</td><td>930</td><td colspan="2">1670...2240</td></tr>
<tr><td>72</td><td></td><td>40Х</td><td>4543-71</td><td>ОП</td><td>2030</td><td colspan="2">Отжиг 860°...900° Закалка 850° Отпуск 500°</td><td>990</td><td colspan="2">1750...2240</td></tr>
<tr><td>73</td><td></td><td>45Х</td><td>4543-71</td><td>ОП</td><td>2030</td><td colspan="2">Отжиг 840°...870° Закалка 840° Отпуск 520°</td><td>1030</td><td colspan="2">1750...2240</td></tr>
<tr><td>74</td><td>Хромованади-</td><td>50Х</td><td>4573-71</td><td>ОП</td><td>2240</td><td colspan="2">Закалка 830° Отпуск 520°</td><td>1080</td><td colspan="2">2240</td></tr>
<tr><td>75</td><td>евая</td><td>15ХФ</td><td>4543-71</td><td>ОП</td><td>1830</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>76</td><td></td><td>80ХФ</td><td>4543-71</td><td>ОП</td><td>1830</td><td colspan="2">Нормализация 880°...900°</td><td>&lt;= 790</td><td colspan="2">1670...2130</td></tr>
<tr><td>77</td><td></td><td>40ХФА</td><td>4543-71</td><td>ОП</td><td>1930</td><td colspan="2">Отпуск 650°</td><td>880</td><td colspan="2">2460</td></tr>
<tr><td>78</td><td>Хромомолиб-</td><td>30ХМ</td><td>4543-71</td><td>ОП</td><td>2240</td><td colspan="2">Закалка 880° Отпуск 540°</td><td>730</td><td colspan="2">2890</td></tr>
<tr><td>79</td><td>деновая</td><td>35ХМ</td><td>4543-71</td><td>ОП</td><td>2360</td><td colspan="2">Отжиг 840°...860° Закалка 850° Отпуск 560°</td><td>970</td><td colspan="2">1830...2240</td></tr>
<tr><td>80</td><td>Хромокремнис-</td><td>33ХС</td><td>4543-71</td><td>ОП</td><td>2360</td><td colspan="2">Закалка 920° Отпуск 630°</td><td>890</td><td colspan="2">2720</td></tr>
<tr><td>81</td><td>тая</td><td>38ХС</td><td>4543-71</td><td>ОП</td><td>2500</td><td colspan="2">Закалка 900° Отпуск 630°</td><td>930</td><td colspan="2">2890</td></tr>
<tr><td>82</td><td>Хромомарган-</td><td>40ХС</td><td>4543-71</td><td>ОП</td><td>-</td><td colspan="2">Закалка 900° Отпуск 540°</td><td>1230</td><td colspan="2">-</td></tr>
<tr><td>83</td><td>цевая</td><td>20ХГ</td><td>4543-71</td><td>ОП</td><td>1830</td><td colspan="2">Закалка 880° Отпуск 480°</td><td>890</td><td colspan="2">2610</td></tr>
<tr><td>84</td><td></td><td>40ХГ</td><td>4593-71</td><td>ОП</td><td>2240</td><td colspan="2">Закалка 840° Отпуск 520°</td><td>930</td><td colspan="2">2890</td></tr>
<tr><td>85</td><td>Кремнемарган-</td><td>35ХГА</td><td>4543-71</td><td>ОП</td><td>-</td><td colspan="2">Закалка 860° Отпуск 600°</td><td>830</td><td colspan="2">-</td></tr>
<tr><td>86</td><td>цевая</td><td>27СГ</td><td>4543-71</td><td>ОП</td><td>2130</td><td colspan="2">Закалка 920° Отпуск 420°</td><td>930</td><td colspan="2">1250</td></tr>
<tr><td>87</td><td></td><td>35СГ</td><td>4543-71</td><td>ОП</td><td>2240</td><td colspan="2">Закалка 900° Отпуск 650°</td><td>890</td><td colspan="2">2610</td></tr>
<tr><td>88</td><td>Хромок-</td><td>36Г26</td><td>4543-71</td><td>ОП</td><td>1240</td><td colspan="2">Закалка 880°</td><td>770</td><td colspan="2">2290</td></tr>
<tr><td>89</td><td>ремнемарган-</td><td>20ХГСА</td><td>4543-71</td><td>ОП</td><td>2030</td><td colspan="2">Закалка 880° Отпуск 500°</td><td>740</td><td colspan="2">2030</td></tr>
<tr><td>90</td><td>цевая</td><td>25ХГСА</td><td>4543-71</td><td>ОП</td><td>2130</td><td colspan="2">Закалка 880° Отпуск 480°</td><td>1080</td><td colspan="2">2300</td></tr>
<tr><td>91</td><td></td><td>30ХГС</td><td>4543-71</td><td>ОП</td><td>2240</td><td colspan="2">Закалка 880° Отпуск 540°</td><td>1080</td><td colspan="2">3190</td></tr>
<tr><td>92</td><td>Хромоникеле-</td><td>35ХГСА</td><td>4543-71</td><td>ОП</td><td>2240</td><td colspan="2">Закалка 950° Отпуск 700°</td><td>1080</td><td colspan="2">-</td></tr>
<tr><td>93</td><td>вая</td><td>12ХН2</td><td>4543-71</td><td>ОП</td><td>2030</td><td colspan="2">Закалка Отпуск 110°</td><td>790</td><td colspan="2">1600...2080</td></tr>
<tr><td>94</td><td></td><td>12Х2Н4</td><td>4543-71</td><td>ОП</td><td>2500</td><td colspan="2">Закалка 760°...810°</td><td>930</td><td colspan="2">1830...2300</td></tr>
<tr><td>95</td><td>Хромоникеле-</td><td>13Н2ХН</td><td>4543-71</td><td>ОП</td><td>2030</td><td colspan="2">Закалка Отпуск 180°</td><td>590</td><td colspan="2">-</td></tr>
<tr><td>96</td><td>вая</td><td>40ХН</td><td>4573-71</td><td>ОП</td><td>2030</td><td colspan="2">Закалка ...500° Отпуск 500°</td><td>990</td><td colspan="2">1780...2130</td></tr>
<tr><td>97</td><td>Хромоникелевая</td><td>20ХН</td><td>4573-71</td><td>ОП</td><td>1930</td><td colspan="2">Закалка 860°...910° Отпуск 180°</td><td>790</td><td colspan="2">1600...2030</td></tr>
<tr><td>98</td><td></td><td>30ХН3А</td><td>4543-71</td><td>ОП</td><td>2360</td><td colspan="2">Закалка 820° Отпуск 530°</td><td>990</td><td colspan="2">1780...2130</td></tr>
<tr><td>99</td><td></td><td>45ХН</td><td>4543-71</td><td>ОП</td><td>2030</td><td colspan="2">Отжиг 850° Закалка 820°</td><td>-</td><td colspan="2">1830...2240</td></tr>
<tr><td>100</td><td></td><td>50ХН</td><td>4543-71</td><td>ОП</td><td>2030</td><td colspan="2">Отпуск 530° Отжиг 830 - 850°</td><td>1030</td><td colspan="2">1830...2240</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="10%"><col width="10%"><col width="9%"><col width="13%"><col width="8%"><col width="9%"><col width="10%"><col width="4%"><col width="12%"></colgroup>
<tr><td colspan="7">Механические свойства основных конструкционных углеродистых и легированных сталей</td><td colspan="3">Приложение 8</td><td>лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Группа стали</td><td rowspan="3">Марка</td><td colspan="8">Механические свойства</td></tr>
<tr><td colspan="3">В состоянии поставки по ГОСТу</td><td colspan="5">После термической обработки</td></tr>
<tr><td>ГОСТ</td><td>Состояние</td><td>сигма , в МПа или НВ, МПа</td><td colspan="2">Типовая термическая обработка</td><td>сигма , в МПа</td><td colspan="2">НВ, МПа</td></tr>
<tr><td>101</td><td>Хромомарган-</td><td>18ХГТ</td><td>4543-71</td><td>ОП</td><td>2130</td><td colspan="2">Нормализация 920°...950°</td><td>990</td><td colspan="2">1540...2030</td></tr>
<tr><td>102</td><td>цевая с титаном</td><td>20ХГТ</td><td>4543-71</td><td>ОП</td><td>2240</td><td colspan="2">Отжиг 870°...890°</td><td>1470</td><td colspan="2">1750...2240</td></tr>
<tr><td>103</td><td>Боросодержа-</td><td>20ХГР</td><td>4573-71</td><td>ОП</td><td>-</td><td colspan="2">Отжиг 860°...880°</td><td>990</td><td colspan="2">1530...1930</td></tr>
<tr><td>104</td><td>щая</td><td>40ХГР</td><td>4573-71</td><td>ОП</td><td>2360</td><td colspan="2">Закалка 850° Отпуск 550°...600°</td><td>990</td><td colspan="2">2890</td></tr>
<tr><td>105</td><td>Хромоникель-</td><td>38ХГН</td><td>4543-71</td><td>ОП</td><td>2240</td><td colspan="2">Закалка 850° Отпуск 510°</td><td>890</td><td colspan="2">2610</td></tr>
<tr><td>106</td><td>марганцевая</td><td>30ХГНА</td><td>4543-71</td><td>ОП</td><td>2240</td><td colspan="2">Закалка 880° Отпуск 500° Отжиг 840°...880°</td><td>1080 -</td><td colspan="2">3190 1750...2240</td></tr>
<tr><td>107</td><td>Хромоникельмолибденовая</td><td>40ХНМА</td><td>4573-71</td><td>ОП</td><td>2640</td><td colspan="2">Закалка 850° Отпуск 620°</td><td>1080</td><td colspan="2">2890</td></tr>
<tr><td>108</td><td>Хромомолибденоалюминиевая</td><td>38ХНМА</td><td>4543-71</td><td>ОП</td><td>2640</td><td colspan="2">Отжиг 930°...980°</td><td>-</td><td colspan="2">1830...2240</td></tr>
<tr><td>109</td><td>Хромовольфрамоалюминиевая с ванадием</td><td>38ХВНРР</td><td>4573-71</td><td>СП</td><td>2240</td><td colspan="2">Закалка 930° Отпуск 640°</td><td>990</td><td colspan="2">2890</td></tr>
<tr><td>110</td><td>Нержавеющая</td><td>2Х13</td><td>5949-75</td><td>Г</td><td>1240... 1930</td><td colspan="2">Закалка 1000°... 1050° Отпуск 660°...770°</td><td>- 650</td><td colspan="2">&lt;= 1830 1910</td></tr>
<tr><td>111</td><td></td><td>4Х13</td><td>5949-75</td><td>Г</td><td>-</td><td colspan="2">Закалка 1000°... 1050° Отпуск 200°...300°</td><td>-</td><td colspan="2">490</td></tr>
<tr><td>112</td><td></td><td>Х18Н9</td><td>5949-75</td><td>Г</td><td>-</td><td colspan="2">Закалка 1050°... 1100°</td><td>490</td><td colspan="2">-</td></tr>
<tr><td>113</td><td></td><td>Х18Н9Т</td><td>5949-75</td><td>Г</td><td>-</td><td colspan="2">Закалка 1050°... 1100°</td><td>540</td><td colspan="2">-</td></tr>
</table>







<a id="p102280"></a>

<table>
<colgroup><col width="12%"><col width="6%"><col width="23%"><col width="28%"><col width="8%"><col width="23%"></colgroup>
<tr><td colspan="6">Механические свойства чугуна и медных сплавов Приложение 9</td></tr>
<tr><td colspan="3">Серый чугун (ГОСТ 1412-79)</td><td colspan="3">Ковкий чугун (ГОСТ 1215-79)</td></tr>
<tr><td colspan="2">Марка отливки</td><td>НВ, МПа</td><td>Марка отливки</td><td colspan="2">НВ, МПа</td></tr>
<tr><td colspan="2">-</td><td>-</td><td>КЧ 30-6</td><td colspan="2">980...1590</td></tr>
<tr><td colspan="2">СЧ 10</td><td>1400...2240</td><td>КЧ 33-8</td><td colspan="2">980...1590</td></tr>
<tr><td colspan="2">СЧ 15</td><td>1590...2240</td><td>КЧ 35-10</td><td colspan="2">980...1590</td></tr>
<tr><td colspan="2">СЧ 18</td><td>1670...2240</td><td>КЧ 37-12</td><td colspan="2">1070...1590</td></tr>
<tr><td colspan="2">СЧ 20</td><td>1670...2260</td><td>КЧ 45-7</td><td colspan="2">1470...2020</td></tr>
<tr><td colspan="2">СЧ 25</td><td>1760...2450</td><td>КЧ 50-5</td><td colspan="2">1670...2250</td></tr>
<tr><td colspan="2">СЧ 30</td><td>1770...2490</td><td>КЧ 55-4</td><td colspan="2">1860...2360</td></tr>
<tr><td colspan="2">СЧ 35</td><td>1930...2630</td><td>КЧ 60-3</td><td colspan="2">1960...2630</td></tr>
<tr><td colspan="2">СЧ 40</td><td>2090...2790</td><td>КЧ 65-3</td><td colspan="2">2070...2630</td></tr>
<tr><td colspan="2">СЧ 45</td><td>2240...2830</td><td>КЧ 70-2</td><td colspan="2">2630...2790</td></tr>
<tr><td colspan="2">-</td><td>-</td><td>КЧ 80-15</td><td colspan="2">2640...3130</td></tr>
<tr><td colspan="6">Примечание: Перлитоферритный ковкий чугун (ПФ) в ГОСТ 1215-79 не входит.</td></tr>
<tr><td colspan="6">Медные сплавы (ГОСТы 17711-80, 613-79, 493-79, 5017-74)</td></tr>
<tr><td colspan="3">Группа</td><td colspan="2">Марка</td><td>НВ, МПа</td></tr>
<tr><td>Гетеро-</td><td colspan="2">Высокой твердости</td><td colspan="2">БрАЛСН11-6-6</td><td>2450</td></tr>
<tr><td>генные</td><td colspan="2"></td><td colspan="2">БрАЛСН10-4-4л</td><td>1670</td></tr>
<tr><td></td><td colspan="2">Средней твердости</td><td colspan="2">БрАОСц10-3-1,5 БР АЖ 9-4</td><td>1180 1070...1760</td></tr>
<tr><td></td><td colspan="2"></td><td colspan="2">БрАМу9-2л ЛМцЖ 52-4-1 БрОУСКЗ-7-5-1 ЛО 67-2,5 ЛК-80-3Л БрОФ6,5-0,15</td><td>780 980 590 880 980...1080 780...880</td></tr>
</table>







<a id="p102175"></a>

<table>
<colgroup><col width="5%"><col width="7%"><col width="5%"><col width="7%"><col width="5%"><col width="7%"><col width="5%"><col width="7%"><col width="5%"><col width="7%"><col width="5%"><col width="6%"><col width="5%"><col width="6%"><col width="5%"><col width="6%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="12">Перевод минут в часы</td><td colspan="6">Приложение 10</td></tr>
<tr><td colspan="2">0,30...0,57</td><td colspan="2">0,58...0,85</td><td colspan="2">0,86...1,75</td><td colspan="2">1,8...3,3</td><td colspan="2">3,4...6,1</td><td colspan="2">6,2...12,5</td><td colspan="2">13...27</td><td colspan="2">27,5...52</td><td colspan="2">53...80</td></tr>
<tr><td>мин.</td><td>час</td><td>мин.</td><td>час</td><td>мин.</td><td>час</td><td>мин.</td><td>час</td><td>мин.</td><td>час</td><td>мин.</td><td>час</td><td>мин.</td><td>час</td><td>мин.</td><td>час</td><td>мин.</td><td>час</td></tr>
<tr><td>0,30</td><td>0,0050</td><td>0,58</td><td>0,0097</td><td>0,86</td><td>0,0143</td><td>1,8</td><td>0,030</td><td>3,4</td><td>0,0567</td><td>6,2</td><td>0,103</td><td>13,0</td><td>0,217</td><td>27,5</td><td>0,459</td><td>53</td><td>0,884</td></tr>
<tr><td>0,31</td><td>0,0052</td><td>0,59</td><td>0,0098</td><td>0,87</td><td>0,0145</td><td>1,85</td><td>0,0309</td><td>3,5</td><td>0,0584</td><td>6,3</td><td>0,105</td><td>13,5</td><td>0,225</td><td>28,0</td><td>0,467</td><td>54</td><td>0,90</td></tr>
<tr><td>0,32</td><td>0,0053</td><td>0,60</td><td>0,010</td><td>0,88</td><td>0,0146</td><td>1,90</td><td>0,0317</td><td>3,6</td><td>0,060</td><td>6,4</td><td>0,106</td><td>14,0</td><td>0,234</td><td>28,5</td><td>0,475</td><td>55</td><td>0,917</td></tr>
<tr><td>0,33</td><td>0,0055</td><td>0,61</td><td>0,0102</td><td>0,89</td><td>0,0148</td><td>1,95</td><td>0,0325</td><td>3,7</td><td>0,0617</td><td>6,5</td><td>0,108</td><td>14,5</td><td>0,242</td><td>29,0</td><td>0,484</td><td>56</td><td>0,934</td></tr>
<tr><td>0,34</td><td>0,0057</td><td>0,62</td><td>0,0103</td><td>0,90</td><td>0,0150</td><td>2,0</td><td>0,0333</td><td>3,8</td><td>0,0634</td><td>6,6</td><td>0,110</td><td>15,0</td><td>0,250</td><td>29,5</td><td>0,492</td><td>57</td><td>0,950</td></tr>
<tr><td>0,35</td><td>0,0058</td><td>0,63</td><td>0,0106</td><td>0,92</td><td>0,0153</td><td>2,05</td><td>0,0342</td><td>3,9</td><td>0,0650</td><td>6,7</td><td>0,112</td><td>15,5</td><td>0,258</td><td>30</td><td>0,50</td><td>58</td><td>0,957</td></tr>
<tr><td>0,36</td><td>0,0060</td><td>0,64</td><td>0,0107</td><td>0,93</td><td>0,0155</td><td>2,10</td><td>0,0350</td><td>4,0</td><td>0,0667</td><td>6,8</td><td>0,113</td><td>16,0</td><td>0,267</td><td>31</td><td>0,517</td><td>59</td><td>0,984</td></tr>
<tr><td>0,37</td><td>0,0062</td><td>0,65</td><td>0,0108</td><td>0,94</td><td>0,0157</td><td>2,15</td><td>0,0359</td><td>4,1</td><td>0,0684</td><td>6,9</td><td>0,115</td><td>16,5</td><td>0,275</td><td>32</td><td>0,535</td><td>60</td><td>1,0</td></tr>
<tr><td>0,38</td><td>0,0064</td><td>0,66</td><td>0,0110</td><td>0,95</td><td>0,0158</td><td>2,20</td><td>0,0367</td><td>4,2</td><td>0,070</td><td>7,0</td><td>0,117</td><td>17,0</td><td>0,284</td><td>33</td><td>0,550</td><td>61</td><td>1,02</td></tr>
<tr><td>0,39</td><td>0,0070</td><td>0,67</td><td>0,0112</td><td>0,96</td><td>0,0160</td><td>2,25</td><td>0,0375</td><td>4,3</td><td>0,0718</td><td>8,7</td><td>0,145</td><td>17,5</td><td>0,292</td><td>34</td><td>0,567</td><td>62</td><td>1,03</td></tr>
<tr><td>0,40</td><td>0,0067</td><td>0,68</td><td>0,0113</td><td>0,97</td><td>0,0161</td><td>2,30</td><td>0,0384</td><td>4,4</td><td>0,0734</td><td>8,8</td><td>0,146</td><td>18,0</td><td>0,30</td><td>35</td><td>0,584</td><td>63</td><td>1,05</td></tr>
<tr><td>0,41</td><td>0,0068</td><td>0,69</td><td>0,0115</td><td>0,98</td><td>0,0163</td><td>2,35</td><td>0,0392</td><td>4,5</td><td>0,0750</td><td>8,9</td><td>0,148</td><td>18,5</td><td>0,309</td><td>36</td><td>0,60</td><td>64</td><td>1,07</td></tr>
<tr><td>0,42</td><td>0,0070</td><td>0,70</td><td>0,0117</td><td>1,00</td><td>0,0167</td><td>2,40</td><td>0,040</td><td>4,6</td><td>0,0767</td><td>9,0</td><td>0,150</td><td>19,0</td><td>0,317</td><td>37</td><td>0,617</td><td>65</td><td>1,08</td></tr>
<tr><td>0,43</td><td>0,0072</td><td>0,71</td><td>0,0118</td><td>1,05</td><td>0,0175</td><td>2,45</td><td>0,0409</td><td>4,7</td><td>0,0784</td><td>9,1</td><td>0,151</td><td>19,5</td><td>0,325</td><td>38</td><td>0,634</td><td>66</td><td>1,10</td></tr>
<tr><td>0,44</td><td>0,0074</td><td>0,72</td><td>0,0120</td><td>1,10</td><td>0,0184</td><td>2,50</td><td>0,0417</td><td>4,8</td><td>0,080</td><td>9,2</td><td>0,153</td><td>20,0</td><td>0,333</td><td>39</td><td>0,650</td><td>67</td><td>1,12</td></tr>
<tr><td>0,45</td><td>0,0075</td><td>0,73</td><td>0,0122</td><td>1,15</td><td>0,0192</td><td>2,55</td><td>0,0425</td><td>4,9</td><td>0,0817</td><td>9,3</td><td>0,155</td><td>20,5</td><td>0,342</td><td>40</td><td>0,667</td><td>68</td><td>1,13</td></tr>
<tr><td>0,46</td><td>0,0077</td><td>0,74</td><td>0,0123</td><td>1,20</td><td>0,020</td><td>2,60</td><td>0,0434</td><td>5,0</td><td>0,0834</td><td>9,4</td><td>0,157</td><td>21,0</td><td>0,350</td><td>41</td><td>0,684</td><td>69</td><td>1,15</td></tr>
<tr><td>0,47</td><td>0,0078</td><td>0,75</td><td>0,0125</td><td>1,25</td><td>0,0288</td><td>2,65</td><td>0,0442</td><td>5,1</td><td>0,0850</td><td>9,5</td><td>0,158</td><td>21,5</td><td>0,359</td><td>42</td><td>0,70</td><td>70</td><td>1,17</td></tr>
<tr><td>0,48</td><td>0,0080</td><td>0,76</td><td>0,0127</td><td>1,30</td><td>0,2170</td><td>2,70</td><td>0,0450</td><td>5,2</td><td>0,0867</td><td>9,6</td><td>0,160</td><td>22,0</td><td>0,367</td><td>43</td><td>0,718</td><td>71</td><td>1,18</td></tr>
<tr><td>0,49</td><td>0,0082</td><td>0,77</td><td>0,0128</td><td>1,35</td><td>0,0225</td><td>2,75</td><td>0,0459</td><td>5,3</td><td>0,0884</td><td>9,7</td><td>0,161</td><td>22,5</td><td>0,375</td><td>44</td><td>0,734</td><td>72</td><td>1,20</td></tr>
<tr><td>0,50</td><td>0,0083</td><td>0,78</td><td>0,0130</td><td>1,40</td><td>0,0234</td><td>2,80</td><td>0,0467</td><td>5,4</td><td>0,090</td><td>9,8</td><td>0,163</td><td>23,0</td><td>0,384</td><td>45</td><td>0,750</td><td>73</td><td>1,22</td></tr>
<tr><td>0,51</td><td>0,0085</td><td>0,79</td><td>0,0132</td><td>1,45</td><td>0,0242</td><td>2,85</td><td>0,0475</td><td>5,5</td><td>0,0917</td><td>9,9</td><td>0,165</td><td>23,5</td><td>0,392</td><td>46</td><td>0,767</td><td>74</td><td>1,23</td></tr>
<tr><td>0,52</td><td>0,0087</td><td>0,80</td><td>0,0133</td><td>1,50</td><td>0,0250</td><td>2,90</td><td>0,0484</td><td>5,6</td><td>0,0934</td><td>10,0</td><td>0,167</td><td>24,0</td><td>0,40</td><td>47</td><td>0,784</td><td>75</td><td>1,25</td></tr>
<tr><td>0,53</td><td>0,0088</td><td>0,81</td><td>0,0135</td><td>1,55</td><td>0,0258</td><td>2,95</td><td>0,0492</td><td>5,7</td><td>0,0950</td><td>10,5</td><td>0,179</td><td>24,5</td><td>0,409</td><td>48</td><td>0,80</td><td>76</td><td>1,27</td></tr>
<tr><td>0,54</td><td>0,0090</td><td>0,82</td><td>0,0137</td><td>1,60</td><td>0,0267</td><td>3,0</td><td>0,050</td><td>5,8</td><td>0,0967</td><td>11,0</td><td>0,183</td><td>25,0</td><td>0,417</td><td>49</td><td>0,817</td><td>77</td><td>1,28</td></tr>
<tr><td>0,55</td><td>0,0092</td><td>0,83</td><td>0,0138</td><td>1,65</td><td>0,0275</td><td>3,1</td><td>0,0517</td><td>5,9</td><td>0,0984</td><td>11,5</td><td>0,192</td><td>25,5</td><td>0,425</td><td>50</td><td>0,834</td><td>78</td><td>1,30</td></tr>
<tr><td>0,56</td><td>0,0094</td><td>0,84</td><td>0,0140</td><td>1,70</td><td>0,0284</td><td>3,2</td><td>0,0535</td><td>6,0</td><td>0,10</td><td>12,0</td><td>0,20</td><td>26,0</td><td>0,434</td><td>51</td><td>0,850</td><td>79</td><td>1,32</td></tr>
<tr><td>0,57</td><td>0,0095</td><td>0,85</td><td>0,0142</td><td>1,75</td><td>0,0292</td><td>3,3</td><td>0,0550</td><td>6,1</td><td>0,102</td><td>12,5</td><td>0,208</td><td>27,0</td><td>0,450</td><td>52</td><td>0,867</td><td>80</td><td>1,33</td></tr>
</table>







### <a id="p102206"></a>УСЛОВНЫЕ ОБОЗНАЧЕНИЯ



<table>
<colgroup><col width="14%"><col width="20%"><col width="66%"></colgroup>
<tr><td>Обозначение</td><td>Единица измерения</td><td>Наименование параметров</td></tr>
<tr><td>1</td><td>2</td><td>3</td></tr>
<tr><td colspan="3">Размеры обработки</td></tr>
<tr><td>D, d</td><td>мм</td><td>Диаметр обрабатываемой детали, инструмента</td></tr>
<tr><td>В</td><td>мм</td><td>Ширина обрабатываемой поверхности, паза</td></tr>
<tr><td>t</td><td>мм</td><td>Глубина резания</td></tr>
<tr><td>Н</td><td>мм</td><td>Глубина обрабатываемого паза</td></tr>
<tr><td>l</td><td>мм</td><td>Путь резания</td></tr>
<tr><td>l 1</td><td>мм</td><td>Величина врезания инструмента</td></tr>
<tr><td>l 2</td><td>мм</td><td>Величина перебега инструмента</td></tr>
<tr><td>i</td><td></td><td>Число рабочих ходов инструмента</td></tr>
<tr><td>L</td><td>мм</td><td>Расчетный путь резания</td></tr>
<tr><td>2h</td><td>мм</td><td>Общий припуск на обработку</td></tr>
<tr><td>h</td><td>мм</td><td>Припуск на одну сторону</td></tr>
<tr><td>v</td><td>м/мин.</td><td>Скорость главного движения</td></tr>
<tr><td>n n дв. х</td><td>об./мин. или дв. ход/мин.</td><td>Частота вращения шпинделя Число двойных ходов стола</td></tr>
<tr><td>Р</td><td>мм</td><td>Шаг резьбы (звездочки к приводным цепям)</td></tr>
<tr><td colspan="3">Режимы обработки</td></tr>
<tr><td>S i</td><td>мм/об.</td><td>Подача на 1 оборот шпинделя</td></tr>
<tr><td>S z</td><td>мм/зуб</td><td>Подача на 1 зуб режущего инструмента</td></tr>
<tr><td>S tх</td><td>мм/ход</td><td>Подача инструмента на глубину резания на один ход стола</td></tr>
<tr><td>S дв.tх</td><td>мм/дв. ход</td><td>Подача инструмента за двойной ход стола</td></tr>
<tr><td>S м</td><td>мм/мин.</td><td>Подача инструмента за одну минуту (минутная)</td></tr>
<tr><td>S поп</td><td>мм/ход</td><td>Подача круга поперечная за один ход стола</td></tr>
<tr><td>N д</td><td>кВт</td><td>Мощность электродвигателя станка</td></tr>
<tr><td>Т</td><td>мин.</td><td>Период стойкости инструмента</td></tr>
<tr><td>фи</td><td>град.</td><td>Главный угол в плане</td></tr>
<tr><td>НВ</td><td>МПа</td><td>Твердость материала по Бринелю</td></tr>
<tr><td>сигма в</td><td>МПа</td><td>Предел прочности материала при растяжении</td></tr>
<tr><td>m</td><td>-</td><td>Величина отношения р.х. / х.х.</td></tr>
<tr><td>V р.х.</td><td>м/мин.</td><td>Скорость главного движения резания</td></tr>
<tr><td>V х.х.</td><td>м/мин.</td><td>Скорость холостого хода</td></tr>
<tr><td>тау</td><td>мин.</td><td>Затраты времени на реверсирование хода стола</td></tr>
<tr><td>z</td><td>-</td><td>Число зубьев (зенкера, развертки)</td></tr>
<tr><td colspan="3">Время</td></tr>
<tr><td>Н вр</td><td>мин.</td><td>Норма времени</td></tr>
<tr><td>Т пз (пз)</td><td>мин.</td><td>Подготовительно-заключительное время</td></tr>
<tr><td>Т ш</td><td>мин.</td><td>Штучное время на операцию</td></tr>
<tr><td>t пер</td><td>мин.</td><td>Вспомогательное время, связанное с переходом</td></tr>
<tr><td>t ву</td><td>мин.</td><td>Вспомогательное время на установку и снятие детали</td></tr>
<tr><td>t нш</td><td>мин.</td><td>Неполное штучное время</td></tr>
<tr><td>Т отл</td><td>-</td><td>Время на отдых и личные потребности в % от оперативного времени</td></tr>
<tr><td>Т обс</td><td>-</td><td>Время на обслуживание рабочего места (техническое и организационное) в % от оперативного времени</td></tr>
<tr><td colspan="3">Поправочные коэффициенты</td></tr>
<tr><td>К тш</td><td>-</td><td>Число деталей в партии</td></tr>
<tr><td>К тв</td><td>-</td><td>Твердость обрабатываемого материала</td></tr>
<tr><td>К пп</td><td>-</td><td>Предел прочности обрабатываемого материала</td></tr>
<tr><td>К сп</td><td>-</td><td>Состояние обрабатываемой поверхности</td></tr>
<tr><td>К ри</td><td>-</td><td>Материал режущего инструмента</td></tr>
<tr><td>К з</td><td>-</td><td>Занятость рабочего</td></tr>
<tr><td>К орм</td><td>-</td><td>Организация рабочих мест на предприятии</td></tr>
<tr><td>К рс</td><td>-</td><td>Число работающих суппортов</td></tr>
<tr><td>К m</td><td>-</td><td>Отношение рабочего хода к холостому ходу</td></tr>
<tr><td>К N</td><td>-</td><td>Мощность привода станка</td></tr>
<tr><td>К фи</td><td>-</td><td>Главный угол в плане</td></tr>
<tr><td>К ф</td><td>-</td><td>Форма обрабатываемой поверхности</td></tr>
<tr><td>К ш</td><td>-</td><td>Шероховатость поверхности</td></tr>
<tr><td>К ро</td><td>-</td><td>Угол наклона (зуба)</td></tr>
<tr><td>К в</td><td>-</td><td>Вид нарезаемого зуба (внутренний, наружный)</td></tr>
<tr><td>К т</td><td>-</td><td>Точность обработки</td></tr>
<tr><td>К тж</td><td>-</td><td>Точность и жесткость станка</td></tr>
<tr><td>К ос</td><td>-</td><td>Изменение штучного времени в зависимости от количества станков, обслуживаемых одним рабочим</td></tr>
</table>




<a id="p100010"></a>

---