---
title: "Постановление Госкомтруда СССР, Секретариата ВЦСПС от 29.06.1990 N 257/10-63"
number: "257/10-63"
issued_on: 1990-06-29
status: утратил силу
canonical: "https://bukva.ai/docs/postanovlenie-25710-63"
---

## Постановление Госкомтруда СССР, Секретариата ВЦСПС от 29.06.1990 N 257/10-63

# Постановление Госкомтруда СССР, Секретариата ВЦСПС от 29.06.1990 N 257/10-63

"Об утверждении Общемашиностроительных нормативов времени на котельные работы (правка, гибка, сборка)"

> [!WARNING]
> Документ утратил силу на территории Российской Федерации в связи с изданием Постановления Правительства РФ от 13.06.2020 N 857.
> Срок действия Общемашиностроительных [нормативов](#p100013), утвержденных данным документом, установлен до 1996 года ([Постановление](#p100007) Госкомтруда СССР, Секретариата ВЦСПС от 29.06.1990 N 257/10-63).
> В соответствии с Трудовым кодексом РФ системы нормирования труда определяются работодателем с учетом мнения представительного органа работников или устанавливаются коллективным договором. Для однородных работ могут разрабатываться и устанавливаться типовые (межотраслевые, отраслевые, профессиональные и иные) нормы труда в соответствии с Правилами, утвержденными Постановлением Правительства РФ от 11.11.2002 N 804.


<a id="p100001"></a>**ГОСУДАРСТВЕННЫЙ КОМИТЕТ СССР ПО ТРУДУ**
**И СОЦИАЛЬНЫМ ВОПРОСАМ**

<a id="p100002"></a>**СЕКРЕТАРИАТ ВСЕСОЮЗНОГО ЦЕНТРАЛЬНОГО СОВЕТА**
**ПРОФЕССИОНАЛЬНЫХ СОЮЗОВ**


## <a id="p100003"></a>ПОСТАНОВЛЕНИЕ

от 29 июня 1990 г. N 257/10-63

<a id="p100004"></a>**ОБ УТВЕРЖДЕНИИ ОБЩЕМАШИНОСТРОИТЕЛЬНЫХ НОРМАТИВОВ ВРЕМЕНИ**
**НА КОТЕЛЬНЫЕ РАБОТЫ (ПРАВКА, ГИБКА, СБОРКА)**

<a id="p100005"></a>Государственный комитет СССР по труду и социальным вопросам и Секретариат Всесоюзного Центрального Совета Профессиональных Союзов постановляют:
1. <a id="p100006"></a>Утвердить Общемашиностроительные [нормативы](#p100013) времени на котельные работы (правка, гибка, сборка), разработанные ВНИИПТхиммаш Минтяжмаша СССР совместно с Центральным бюро нормативов по труду Государственного комитета СССР по труду и социальным вопросам при участии нормативно-исследовательских организаций, объединений и предприятий Министерства тяжелого машиностроения СССР.
<a id="p100007"></a>Установить срок их действия до 1996 г.
2. <a id="p100008"></a>Общемашиностроительные [нормативы](#p100013) времени рекомендуются для применения на машиностроительных предприятиях независимо от их ведомственной подчиненности.
3. <a id="p100009"></a>Центральному бюро нормативов по труду Государственного комитета СССР по труду и социальным вопросам обеспечить контроль за изданием сборника "Общемашиностроительные нормативы времени на котельные работы (правка, гибка, сборка)" в соответствии с тематическим планом издания.
4. <a id="p100010"></a>С введением в действие Общемашиностроительных [нормативов](#p100013) времени на котельные работы (правка, гибка, сборка), утвержденных настоящим Постановлением, признать утратившими силу Общемашиностроительные нормативы времени на котельные работы (правка, гибка, сборка). М., НИИ труда, 1982 г.

<div align="right">

<a id="p100011"></a>Заместитель Председателя<br>
Государственного комитета СССР<br>
по труду и социальным вопросам<br>
**Б.ГАВРИЛОВ**

<a id="p100012"></a>Секретарь<br>
Всесоюзного Центрального Совета<br>
Профессиональных Союзов<br>
**В.МИШИН**

</div>







## <a id="p100013"></a>ОБЩЕМАШИНОСТРОИТЕЛЬНЫЕ НОРМАТИВЫ ВРЕМЕНИ НА КОТЕЛЬНЫЕ РАБОТЫ (ПРАВКА, ГИБКА, СБОРКА)


<a id="p100014"></a>Общемашиностроительные нормативы времени на котельные работы (правка, гибка, сборка) разработаны Центральным бюро нормативов по труду совместно с "ВНИИТхиммаш", утверждены Постановлением Государственного комитета СССР по труду и социальным вопросам и Секретариата ВЦСПС от 29 июня 1990 г. N 257/10-63 и рекомендованы для применения при нормировании труда рабочих, занятых котельными работами на предприятиях со среднесерийными, мелкосерийными и единичными типами производства, независимо от ведомственной подчиненности форм, собственности и хозяйствования.
<a id="p100015"></a>Сборник содержит: нормативы подготовительно-заключительного времени; нормативы штучного времени на установочные работы; на правку и гибку деталей; укрупненные нормативы штучного времени и дифференцированные нормативы штучного времени на слесарные и слесарно-сборочные работы.


### 1. <a id="p100016"></a>ОБЩАЯ ЧАСТЬ


<a id="p100017"></a>1.1. Общемашиностроительные нормативы времени предназначены для нормирования котельных работ на машиностроительных предприятиях с единичными, мелкосерийными и среднесерийными типами производства.
<a id="p100018"></a>Тип производства характеризуется коэффициентом закрепления операций в соответствии с ГОСТ 3.1121-84.

#### <a id="p100019"></a>1.2 В основу разработки нормативов времени приняты следующие данные:

<a id="p100020"></a>хронометражные наблюдения;
<a id="p100021"></a>фотографии рабочего времени;
<a id="p100022"></a>технические характеристики инструмента, оборудования;
<a id="p100023"></a>результаты анализа организации труда и мероприятий по ее совершенствованию.
<a id="p100024"></a>1.3. Нормативы охватывают профессии рабочих котельно-сборочных цехов: вальцовщиков, штамповщиков, котельщиков, правильщиков, слесарей по сборке металлоконструкций.
<a id="p100025"></a>1.4. В нормативных картах приведены эмпирические формулы, по которым рассчитано штучное время на комплексы приемов в зависимости от принятых факторов с последующим округлением, которые могут быть использованы при расчете норм времени с применением ЭВМ.
<a id="p100026"></a>1.5. Предусмотренные в картах сборника в содержании работ приемы "Подать деталь или узел и снять" следует понимать: "Застропить деталь или узел, переместить в рабочей зоне, отстропить деталь, узел". При перемещении нескольких деталей одновременно грузоподъемными средствами в нормативных картах время рассчитано на одну деталь.
<a id="p100027"></a>Числовые значения факторов (масса, расстояние перемещения, габариты (и др.)), приведенные в системе "до", следует понимать включительно.
<a id="p100028"></a>1.6. При выполнении работ с помощью подъемного крана время на его вызов в размере 1,3 мин. добавляется к норме штучного времени в каждом случае.

#### <a id="p100029"></a>1.7 Нормативная [часть](#p100194) сборника состоит из 5 разделов.

<a id="p100030"></a>[Раздел 1](#p100195). Нормативы подготовительно-заключительного времени. Нормативы штучного времени на установочные работы.
<a id="p100031"></a>[Раздел 2](#p100332). Нормативы штучного времени на правку деталей.
<a id="p100032"></a>[Раздел 3](#p101099). Нормативы штучного времени на гибку деталей.
<a id="p100033"></a>[Раздел 4](#p103090). Укрупненные нормативы штучного времени на слесарные и слесарно-сборочные работы.
<a id="p100034"></a>[Раздел 5](#p105192). Дифференцированные нормативы штучного времени на слесарные и слесарно-сборочные работы.
<a id="p100035"></a>1.8. Нормативы времени рассчитаны в человеко-минутах при продолжительности обработки партии изделий свыше 0,5 до 1 смены. При измененных условиях обработки партии изделий приведенное в нормативных картах время применяется с коэффициентами:

<div align="right">

<a id="p100036"></a>Таблица 1

</div>



<table>
<colgroup><col width="29%"><col width="38%"><col width="32%"></colgroup>
<tr><td colspan="3">Трудоемкость обработки партии изделий</td></tr>
<tr><td>до 0,5 смены</td><td>св. 0,5 смены до 1 смены</td><td>свыше 1 смены</td></tr>
<tr><td colspan="3">Коэффициент К</td></tr>
<tr><td>1,1</td><td>1,0</td><td>0,9</td></tr>
</table>


<a id="p100040"></a>1.9. Нормативами времени учтено перемещение деталей, узлов в пределах рабочей зоны на расстоянии от 2 до 10 м в зависимости от габаритов деталей.
<a id="p100041"></a>1.10. Нормативы времени рассчитаны на выполнение работ в удобном положении рабочего. При сборке на высоте, в закрытых емкостях, в неудобных местах, где имеются препятствия, ограничивающие свободные движения рабочего, к времени по картам применять коэффициенты:

<div align="right">

<a id="p100042"></a>Таблица 2

</div>



<table>
<colgroup><col width="15%"><col width="32%"><col width="14%"><col width="38%"></colgroup>
<tr><td colspan="4">Условия выполнения работ</td></tr>
<tr><td>В удобном положении</td><td>На высоте 1,5 м на сферических и радиальных поверхностях</td><td>В закрытых емкостях</td><td>В местах, ограничивающих свободные движения, и в потолочном положении</td></tr>
<tr><td colspan="4">Коэффициент К 1</td></tr>
<tr><td>1,0</td><td>1,1</td><td>1,2</td><td>1,3</td></tr>
</table>


<a id="p100046"></a>1.11. Прихватка электросваркой производится самими сборщиками или сварщиками ручной сварки, входящими в бригаду сборщиков.
<a id="p100047"></a>В цехах, где электросварщики ручной сварки не входят в бригаду сборщиков, их работа нормируется отдельно по карте 98.
<a id="p100048"></a>В таких случаях при расчете нормы времени на выполнение определенной работы время на прихватку, взятое по карте 98, вычитается из времени, приведенного в нормативной карте на данную работу.
<a id="p100049"></a>1.12. В картах сборника приведены нормативы штучного времени в чел.-мин. на комплексы приемов, в которые вошли оперативное время, время организационного и технического обслуживания рабочего места, время на отдых и личные потребности.

##### <a id="p100050"></a>1.12.1 Оперативное время предусматривает следующее содержание работ:

<a id="p100051"></a>доставку и комплектовку деталей, узлов в пределах рабочей зоны;
<a id="p100052"></a>внешний осмотр и промер деталей;
<a id="p100053"></a>установку деталей, кантовку в процессе работы;
<a id="p100054"></a>разметку, подгонку деталей по сопрягаемым кромкам, прихватку электросваркой, крепление болтами, винтами, прижимами, струбцинами, установку технологических колец, подрубку при сборке;
<a id="p100055"></a>проверку размеров собираемого узла;
<a id="p100056"></a>зачистку стыкуемых кромок;
<a id="p100057"></a>сдачу отделу технического контроля.
<a id="p100058"></a>1.12.2. Время на организационно-техническое обслуживание рабочего места включено в штучное время в размере 3% от оперативного времени и включает в себя время:
<a id="p100059"></a>раскладки и уборки инструмента и рабочего места;
<a id="p100060"></a>подключения токопроводов к сварочному посту, включения и регулировки силы тока;
<a id="p100061"></a>подключения пневмоинструмента и электроинструмента к питающей сети;
<a id="p100062"></a>заправки и заточки инструмента.
<a id="p100063"></a>1.12.3. Время на отдых и личные надобности предусмотрено в составе штучного времени в размере 1% от оперативного времени.

##### <a id="p100064"></a>1.12.4 Нормативы времени на подготовительно-заключительную работу приведены отдельно (карта 1) и включают время на:

- <a id="p100065"></a>получение сменного задания, наряда, чертежей, технологической документации и пр.;
- <a id="p100066"></a>ознакомление с технической документацией;
- <a id="p100067"></a>получение инструмента, приспособлений;
- <a id="p100068"></a>подготовку рабочего места;
- <a id="p100069"></a>сдачу технологической документации, инструмента, приспособлений;
- <a id="p100070"></a>сдачу готовой продукции.
<a id="p100071"></a>1.13. Подготовительно-заключительное время установлено в зависимости от сложности выполняемой работы и рассчитано на задание не более чем на одну смену и дано в минутах; на период, когда задание свыше одной смены, - в процентах от штучного времени и в этом случае норма времени на подготовительно-заключительную работу относится к партии одновременно изготавливаемых деталей, узлов и не зависит от размера партии.
<a id="p100072"></a>1.14. Нормативы штучного времени даны в человеко-минутах и рассчитаны на выполнение комплексов приемов котельных работ, предусмотренных в нормативных картах бригадами с технологически необходимой численностью. Время в картах дано на выполнение полного объема работы и не изменяется при расхождении фактической численности состава бригады с нормативной.

#### <a id="p100073"></a>1.15 Расчет нормы времени производится по следующим формулам:

<a id="p100074"></a>При задании, выполняемом не более рабочей смены, норма времени рассчитывается по формуле:

                                                           Тпз
<a id="p100075"></a>                Нвр = (Т  + Т  + Т  + ... + Т ) х К х К  + ---.
                        1    2    3          n         1    n

<a id="p100076"></a>    При    задании,   выполняемом   свыше   одной   смены,  норма   времени
рассчитывается по формуле:

<a id="p100077"></a>                Нвр = (Т  + Т  + Т  + ... + Т ) х К х К  х К ,
                        1    2    3          n         1    2

    где:
<a id="p100078"></a>    Нвр - норма времени, чел.-мин.;
<a id="p100079"></a>    Т ,  Т ,  Т , Т   -  штучное  время  из  нормативных  карт  сборника на
     1    2    3   n
выполнение комплексов котельных работ;
<a id="p100080"></a>    К   -   коэффициент,  учитывающий  продолжительность  обработки  партии
изделий (см. [таблицу 1](#p100036));
<a id="p100081"></a>    К   -   коэффициент,  учитывающий   условия   выполнения  работы   (см.
     1
[таблицу 2](#p100042));
<a id="p100082"></a>    К  - подготовительно-заключительное время, % (см. карту 1);
     2
<a id="p100083"></a>    Тпз - подготовительно-заключительное время, мин. (см. карту 1);
<a id="p100084"></a>    n - количество деталей в партии.
<a id="p100085"></a>1.16. При введении на предприятиях настоящих нормативов необходимо привести организационно-технические условия в соответствии с запроектированными и осуществить производственный инструктаж рабочих.
<a id="p100086"></a>На работы, не предусмотренные сборником, а также при внедрении на предприятиях более прогрессивной организации производства труда, технологии котельных работ следует разрабатывать и вводить в установленном порядке технически обоснованные местные нормативы времени.
<a id="p100087"></a>1.17. Для пояснения порядка пользования нормативами ниже приводятся примеры расчета норм времени.
<a id="p100088"></a>*Пример* 1. Сборка листов в карту
<a id="p100089"></a>Исходные данные:
    1. <a id="p100090"></a>Размеры листов: 6000 х 2500 х 24
                       6000 х 2100 х 24
                       4600 х 2000 х 24.
2. <a id="p100091"></a>Материал - Ст. 45.
3. <a id="p100092"></a>Масштаб выпуска - 3 изделия в партии.


<table>
<colgroup><col width="5%"><col width="30%"><col width="30%"><col width="19%"><col width="16%"></colgroup>
<tr><td>N п/п</td><td>Содержание работы</td><td>Факторы, влияющие на продолжительность работы</td><td>N карты, N позиции, индекс</td><td>Время, чел.-мин.</td></tr>
<tr><td>1.</td><td>Подать первый лист к месту сборки краном и установить на плиту</td><td>Плоские, на плиту Масса М = 2,81 т</td><td>3, поз. 1, з</td><td>Т = 3,54 1</td></tr>
<tr><td>2.</td><td>Подать второй лист к месту сборки, зачистить кромки под сварку, установить и подогнать листы по стыку, выдержав зазоры и уступность кромок. Установить, прихватить сборочные приспособления. Прихватить листы электросваркой</td><td>Длина стыка L = 6000 мм Ширина листа В = 2100 мм Толщина листа h = 24 мм</td><td>59, поз. 36, ж</td><td>Т = 34,4 2</td></tr>
<tr><td>3.</td><td>Подать третий лист к месту сборки, зачистить кромки под сварку, установить и подогнать листы по стыку, выдержав зазоры и уступность кромок. Установить, прихватить сборочные приспособления. Прихватить листы электросваркой</td><td>Длина стыка L = 4600 мм Ширина листа В = 2000 мм Толщина листа h = 24 мм</td><td>59, поз. 32, ж</td><td>Т = 24,7 3</td></tr>
<tr><td>4.</td><td>Срубить сборочные приспособления, зачистить места прихваток</td><td></td><td>59, поз. 36, ж 59, поз. 32, ж</td><td>Время на срубку и зачистку учтено в п. п. 2, 3</td></tr>
<tr><td>5.</td><td>Снять собранную карту, отложить</td><td></td><td>3, поз. 1, з 59, поз. 36, ж 59, поз. 32, ж</td><td>Время на снятие учтено в п. п. 1, 2, 3</td></tr>
<tr><td></td><td>Итого:</td><td></td><td></td><td>62,64</td></tr>
<tr><td></td><td>Подготовительнозаключительное время</td><td>Сложность работы - средняя</td><td>1, поз. 1, б</td><td>11,0</td></tr>
<tr><td rowspan="2"></td><td rowspan="2">-</td><td>Размер партии n = 3</td><td>-</td><td>-</td></tr>
<tr><td>Положение удобное</td><td><a href="#p100042">табл. 2</a></td><td>К = 1,0 1</td></tr>
</table>


<a id="p100102"></a>    Так как (Т  + Т  + Т ) х n = 62,64 х 3 = 187,92 чел.-мин. < 0,5  смены,
              1    2    3
то применяем формулу:

                                                    Тпз
<a id="p100103"></a>                    Нвр = (Т  + Т  + Т ) х К х К  + ---,
                            1    2    3         1    n

    где:
<a id="p100104"></a> К = 1,1 [(табл. 1)](#p100036);
<a id="p100105"></a> К = 1,0 [(табл. 2)](#p100042).
     1

                              11,0
<a id="p100106"></a>    Нвр = 62,64 х 1,1 х 1,0 + ---- = 72,56 чел.-мин.
                               3

<a id="p100107"></a>*Пример* 2. Гибка обечайки в вальцах
<a id="p100108"></a>Исходные данные:
1. <a id="p100109"></a>Размеры листа 2512 х 2400 х 20.
2. <a id="p100110"></a>Материал - Ст. 3.
3. <a id="p100111"></a>Масштаб выпуска - 10 изделий в партии.


<table>
<colgroup><col width="5%"><col width="30%"><col width="30%"><col width="19%"><col width="16%"></colgroup>
<tr><td>N п/п</td><td>Содержание работы</td><td>Факторы, влияющие на продолжительность работы</td><td>N карты, N позиции, индекс</td><td>Время, чел.-мин.</td></tr>
<tr><td>1.</td><td>Подать лист на гибочное приспособление пресса, подвести кромку под пуансон, кромку листа по радиусу, передвигая лист в процесс подгибки, проверить радиус гиба по шаблону, снять лист, отложить</td><td>Длина листа L = 2512 мм Ширина листа (длина подгибаемой кромки) В = 2400 мм Толщина листа h = 20 мм Длина пуансона l = 1,25 м</td><td>23, поз. 38, в</td><td>Т = 13,38 1</td></tr>
<tr><td>2.</td><td>Подать лист к вальцам, заправить кромку листа в вальцы, вальцевать лист в цилиндрическую обечайку, проверить обечайку по диаметру шаблоном, снять обечайку, отложить</td><td>Диаметр обечайки Д = 800 мм Длина обечайки L = 2400 мм Толщина листа h = 20 мм Скорость вращения валков = 6,5 м/мин.</td><td>24, поз. 45, з</td><td>Т = 23,2 2</td></tr>
<tr><td></td><td>Итого:</td><td></td><td></td><td>36,58</td></tr>
<tr><td></td><td>Подготовительнозаключительное время</td><td>Сложность работы - средняя</td><td>1, поз. 1, б</td><td>11,0</td></tr>
<tr><td rowspan="2"></td><td rowspan="2">-</td><td>Размер партии n = 10</td><td>-</td><td>-</td></tr>
<tr><td>Положение удобное</td><td><a href="#p100042">табл. 2</a></td><td>К = 1 1</td></tr>
</table>


<a id="p100118"></a>    Так как (Т  + Т ) х n = 36,58 х 10 = 365,8 чел.-мин. < одной смены,  то
              1    2
применяем формулу:

                                               Тпз
<a id="p100119"></a>                    Нвр = (Т  + Т ) х К х К  + ---,
                            1    2         1    n

    где:
<a id="p100120"></a> К = 1,0 [(табл. 1)](#p100036);
<a id="p100121"></a> К = 1,0 [(табл. 2)](#p100042).
     1

                              11,0
<a id="p100122"></a>    Нвр = 36,58 х 1,0 х 1,0 + ----  = 37,63 чел.-мин.
                               10

<a id="p100123"></a>*Пример* 3. Сборка конической обечайки
<a id="p100124"></a>Исходные данные:
1. <a id="p100125"></a>Размеры обечайки - 1000 х 2700 х 20.
2. <a id="p100126"></a>Материал - Ст. 1Х18Н9Т.
3. <a id="p100127"></a>Масштаб выпуска - 5 изделий в партии.


<table>
<colgroup><col width="5%"><col width="30%"><col width="30%"><col width="19%"><col width="16%"></colgroup>
<tr><td>N п/п</td><td>Содержание работы</td><td>Факторы, влияющие на продолжительность работы</td><td>N карты, N позиции, индекс</td><td>Время, чел.-мин.</td></tr>
<tr><td>1.</td><td>Подать обечайку на сборочный стенд, зачистить кромки под сварку, подогнать продольный стык обечайки, выдержав зазор и уступность кромок, установить, прихватить сборочные приспособления, прихватить стык электросваркой. Снять и срубить сборочные приспособления, зачистить места прихваток. Снять обечайку, отложить</td><td>Больший диаметр обечайки Д = 1000 мм Длина обечайки L = 2700 мм Толщина листа h = 20 мм</td><td>63, поз. 19, ж <a href="#p103235">Примечание I</a></td><td>Т = 29,0 х 1,2 = 34,8</td></tr>
<tr><td></td><td>Итого:</td><td></td><td></td><td>34,8</td></tr>
<tr><td></td><td>Подготовительнозаключительное время</td><td>Сложность работы - средняя</td><td>1, поз. 1, б</td><td>11,0</td></tr>
<tr><td rowspan="2"></td><td rowspan="2">-</td><td>Размер партии</td><td>-</td><td>-</td></tr>
<tr><td>Положение удобное</td><td><a href="#p100042">табл. 2</a></td><td>К = 1,0 1</td></tr>
</table>


<a id="p100134"></a>    Так как Т х n = 34,8 х 5 = 174,0 чел.-мин.  < 0,5 смены,  то  применяем
формулу:

                                             Тпз
<a id="p100135"></a>                          Нвр = Т х К х К  + ---,
                                         1    n

    где:
<a id="p100136"></a> К = 1,1 [(табл. 1)](#p100036);
<a id="p100137"></a> К = 1,0 [(табл. 2)](#p100042).
     1

                             11,0
<a id="p100138"></a>    Нвр = 34,8 х 1,1 х 1,0 + ---- = 40,48 чел.-мин.
                               5

<a id="p100139"></a>*Пример* 4. Сборка корпуса аппарата
<a id="p100140"></a>Исходные данные:
1. <a id="p100141"></a>Размеры обечайки 1200 х 5900 х 24.
2. <a id="p100142"></a>Материал - Ст. 3.
3. <a id="p100143"></a>Масштаб выпуска - 2 изделия в партии.


<table>
<colgroup><col width="5%"><col width="26%"><col width="31%"><col width="19%"><col width="19%"></colgroup>
<tr><td>N п/п</td><td>Содержание работы</td><td>Факторы, влияющие на продолжительность работы</td><td>N карты, N позиции, индекс</td><td>Время, чел.-мин.</td></tr>
<tr><td>1.</td><td>Подать обечайки к месту сборки и установить на роликовые опоры, зачистить кромки под сварку, подогнать стык, установить и прихватить сборочные приспособления, прихватить стык электросваркой</td><td>Диаметр обечайки Д = 1200 мм Суммарная длина обечайки L = 5900 мм Толщина листа h = 24 мм</td><td>66, поз. 9, д</td><td>Т = 37,7 1</td></tr>
<tr><td>2.</td><td>Подать днище к месту сборки, зачистить кромки под сварку, подогнать днище к корпусу, установить, прихватить сборочные приспособления. Прихватить днище с корпусом электросваркой</td><td>Диаметр днища Д = 1200 мм Толщина стенки корпуса h = 24 мм Установка - встык</td><td>68, поз. 9, ж</td><td>Т = 45,0 2</td></tr>
<tr><td>3.</td><td>Взять инструмент и разметить места установки штуцеров, предварительно разметив две главные оси</td><td>Длина корпуса L = 5900 мм Диаметр корпуса Д = 1200 мм Диаметр штуцера dшт = 95 мм Количество штуцеров на одной оси n1 = 2 шт., на второй оси n2 = 1 шт.</td><td>51, поз. 4, и <a href="#p103250">Примеч. II</a>, 2 51, поз. 10, е <a href="#p103284">Примеч. III</a>, 4 51, поз. 10, е</td><td>22,3 х 0,6 = 13,38 3,48 х 0,85 х 2 места = 5,92 3,48 х 1 х 1 место = 3,48 Т = 13,38 + 3 5,92 + 3,48 = 22,78</td></tr>
<tr><td>4.</td><td>Подать штуцеры к месту сборки, подрубить, зачистить и подогнать отверстие под штуцер в корпусе, зачистить кромки под сварку. Установить штуцер на корпус, подогнать с выверкой. Прихватить штуцер к корпусу электросваркой</td><td>Штуцеры вертикальные dшт = 95 мм - 2 шт. Штуцер наклонный dшт = 95 мм - 1 шт. Поверхность цилиндрическая. Толщина стенки корпуса h = 24 мм Длина штуцера Н = 300 мм</td><td>80, поз. 29, г <a href="#p103235">Примеч. I</a> 81, поз. 5, г Примеч. I</td><td>13,5 х 0,85 х 2 места = 22,95 17 х 0,85 х 1 место = 14,45 Т = 22,95 + 4 14,45 = 37,4</td></tr>
<tr><td>5.</td><td>Наметить места установки опор на корпусе аппарата, подать опоры к месту сборки. Зачистить кромки и места установки под сварку, выставить на корпус аппарата накладной лист, подогнать и прихватить электросваркой. Выставить на накладной лист опору, подогнать и прихватить электросваркой</td><td>Масса опоры М = 70 кг Положение аппарата - горизонтальное. Количество опор n = 2</td><td>94, поз. 6, б</td><td>Т = 27,5 х 5 2 = 55,0</td></tr>
<tr><td>6.</td><td>Снять и срубить сборочные приспособления, зачистить места прихваток</td><td></td><td>66, поз. 9, д 68, поз. 9, ж 80, поз. 29, г 81, поз. 5, г 94, поз. 6, б</td><td>Время на срубку и зачистку учтено в п. п. 1, 2, 4, 5</td></tr>
<tr><td>7.</td><td>Снять собранный аппарат, отложить</td><td>Диаметр корпуса Д = 1200 мм Длина корпуса Д = 7000 мм Толщина стенки корпуса h = 24 мм</td><td>66, поз. 9, д</td><td>Время на снятие учтено в п. 1</td></tr>
<tr><td></td><td>Итого:</td><td>Т + Т + Т + Т + Т 1 2 3 4 5</td><td></td><td>197,88</td></tr>
<tr><td></td><td>Подготовительнозаключительное время %</td><td>Сложность работы - сложная</td><td>1, поз. 2, в</td><td>3,6</td></tr>
<tr><td rowspan="2"></td><td rowspan="2">-</td><td>Размер партии n = 2</td><td>-</td><td>-</td></tr>
<tr><td>Положение удобное</td><td><a href="#p100042">табл. 2</a></td><td>К = 1,0 1</td></tr>
</table>


<a id="p100156"></a>    Так как (Т  + Т  + Т  + Т  + Т ) х n = 197,88 х 2 = 395,76 чел.-мин.  >
              1    2    3    4    5
одной рабочей смены, то применяем формулу:

<a id="p100157"></a>                  Нвр = (Т  + Т  + Т  + Т  + Т ) х К х К  х К ,
                          1    2    3    4    5         1    2

    где:
<a id="p100158"></a> К = 0,9 [(табл. 1)](#p100036);
<a id="p100159"></a> К = 1,0 [(табл. 2)](#p100042);
     1
<a id="p100160"></a>    К  = 1,036 (к. 1, поз. 2, в)
     2

<a id="p100161"></a>    Нвр = 197,88 х 0,9 х 1,0 х 1,036 = 184,5 чел.-мин.


### 2. <a id="p100162"></a>ХАРАКТЕРИСТИКА ПРИМЕНЯЕМОГО ОБОРУДОВАНИЯ И ТЕХНОЛОГИЯ РАБОТЫ


<a id="p100163"></a>2.1. Нормативы времени рассчитаны для нормирования котельных работ, выполняемых на оборудовании отечественного производства и некоторых зарубежных фирм. К числу распространенного оборудования для котельных работ относятся:

#### <a id="p100164"></a>2.2 Правильное оборудование

<a id="p100165"></a>Листоправильные пяти-, семивалковые вальцы, модели: UBP, UBP-18/1 и др.; максимальный размер выправляемого листа 3200 - 12000 мм при толщине 4 - 75 мм.
<a id="p100166"></a>Прессы фрикционные, модели: ФА122, ФА124, Ф128 и др. с усилием пресса от 63 до 400 т.
<a id="p100167"></a>Гидравлические прессы правильные, модели: ПА-413, П-3236; П4175, П-3232, ПА-6332, П418В и др., с усилием пресса от 25 до 160 т.

#### <a id="p100168"></a>2.3 Гибочные машины

<a id="p100169"></a>Листогибочные вальцы, модели: И2220, И2220-А; И2220-Б, И2114, И2222, И2426 и др. Максимальные размеры вальцуемого листа - ширина 3200 мм, длина - 12000 мм при толщине 2 - 80 мм.
<a id="p100170"></a>Кромкогибочные прессы, модели: И134, И135, РА100, ПА160 и др., максимальный размер отгибаемого листа - ширина - 2000 мм, длина - 5600 мм при толщине 8 - 10 мм.
<a id="p100171"></a>Трубогибочные машины, модели: СТГ, ГСТМ-21М, ТГ-38-159, И3432А, ГСТМ-216 и др., диаметр изгибаемой трубы - 12 - 160 мм.

#### <a id="p100172"></a>2.4 Ручной инструмент

<a id="p100173"></a>К ручному инструменту относятся зубила и молотки, стальные щетки, пневматические зубила, пневматические машинки с наждачным кругом, керны, кувалды, шаберы, напильники и др.


### 3. <a id="p100174"></a>ОРГАНИЗАЦИЯ ТРУДА


<a id="p100175"></a>3.1. Принятая в нормативах организация труда разработана с учетом прогрессивных форм разделения труда и передового опыта работы на предприятиях.
<a id="p100176"></a>3.2. Нормативы времени предусматривают наиболее рациональную организацию труда и рабочих мест с учетом мощности, производительности, габаритных размеров и расположения гибочных вальцов, правильных плит, прессов и другого оборудования в пределах рабочей зоны.
<a id="p100177"></a>3.3. На участках котельных работ рабочее место должно быть оснащено в соответствии с требованиями производственного процесса и условий выполнения работы, с правилами санитарной гигиены (нормальное освещение и температура помещения, относительная влажность воздуха) и техники безопасности, предусмотренными Государственными нормами по [СН 245-71](https://bukva.ai/docs/sanitarnye-normy-179-gosstroy-sssr-gosudarstvennyy), СНИП II-4-79.
<a id="p100178"></a>3.4. На рабочем месте должно быть расположено оборудование и приспособления для выполнения гибки, правки и сборочных работ котельщика, подачи сжатого воздуха и электротока при применении пневматических и электрических инструментов, предусмотрены необходимые подъемные средства.
<a id="p100179"></a>3.5. Оборудование, подъемно-транспортные средства, инструмент и приспособления находятся в исправном состоянии.
<a id="p100180"></a>3.6. Получение работы, нарядов, чертежей и технологической документации производится на рабочем месте.
<a id="p100181"></a>3.7. Инструменты и приспособления исполнитель работы получает в раздаточной кладовой.
<a id="p100182"></a>3.8. Планировка рабочих мест и система их обслуживания разработаны с использованием типовых проектов организации рабочих мест котельщиков (проекты подготовлены по материалам ЦПКТБ НОТ, Министерства нефтяного и химического машиностроения) "Типовые проекты организации рабочих мест котельщиков и сварщиков", изд. 1977 г.
<a id="p100183"></a>Ниже приведены схемы планировок рабочих мест котельщиков.

                                  32000

<a id="p100184"></a><a id="p100185"></a><a id="p100186"></a><a id="p100187"></a>

```text
      <─────────────────────────────────────────────────────────>
      ├─────────────────────────────────────────────────────────┼────────
      │                                                         │      /\
      └─────────────────────────────────────────┬─────┬┬────────┘      │
        /                                 10 ───┼─    ││               │
       /                                        └┬┬─┬┬┴┘\          6000│
      /                                          │├─┤│   \ 11          │
     /┌─────┐ ┌──┐ ┌──┐  ┌────┐   ┌──┐  ┌──┐     │├─┤│    \__          │
    / │     │ ├──┤ │  │  │    │   │  │  │  │     │├─┤│                 \/
   /  └─────┘ └┬─┘ └─┬┘  └─┬──┘ 0 └──┘  └──┘     └┴┬┴┴───────────────────
  /     /      │     │     │     \    \     \      │
 /1    /2      │3    │4    │5     \ 6  \ 7   \ 8   │9
/__   /__      └─    └─    └─      \_   \_    \_   └─

Планировка рабочего места котельщиков для сборки
патрубков, люков, штуцеров, кронштейнов и т.п.
с цилиндрическими корпусами и прихватками

1 - роликовый стенд; 2 - стол для хранения арматуры; 3 - стеллаж для баллонов; 4 - шкаф; 5 - слесарный верстак; 6 - стойка с цветной сигнальной лампочкой для выхода внутрицехового транспорта; 7 - мусоросборник; 8 - передвижной столик; 9 - лестница; 10 - ящик для огарков; 11 - ящик для электродов.

                                      ┌──────┬─────────────────────────────
                                      │      │  ┌─────┐  О  ┌──┐         /\
                                      └─/────┘  └─/───┘  /  └──┘         │
                                     2 /       3 /    4 /  5 /           │
                                     _/        _/     _/   _/            │
                                                                         │
                                                        6   7            │
                                                        _   _            │
                                                       /   /             │
               1                                      /   /              │
              ┌─                                     ┌─┬─┐           9500│
              │                                      ├─┴─┤               │
      ┌───────┼───────────────┐                      │   │               │
      │                       │                      │   │    ┌─────┐    │
      ├───────────────────────┘                      │   │    │     │    │
      │                                              │   │    │     │    │
      │                                              │   │    │     │    │
      │ ┌─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┐                       │   │    │     │    │
      │                                              │   │    │     │    \/
      │ └ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─┘ 10                    └──\┘9   └\────┼──────
      │                       \__                        \_     \ 8 │
      │                                21000                     \_ │
      │<───────────────────────────────────────────────────────────>│

Планировка рабочего места вальцовщика

1 - рольганг; 2 - стеллаж для длиномерного инструмента; 3 - тумбочка; 4 - стойка с цветной сигнальной лампочкой для вызова внутрицехового транспорта; 5 - мусоросборник; 6 - ящик для огарков; 7 - ящик для электродов; 8 - стеллаж для складирования обечаек; 9 - листогибочные трехвалковые вальцы; 10 - место для складирования листа.

                            ┌───────────────────────────────────┬───────
                   1 ───────┼──                                 │      /\
                            └───────────────────────────────────┘      │
            3      4     2                                             │
            _      _     ──┬───────┐                                   │
             \      \      │       │                                   │
              \      \     │┌─────┬┴────┬─────┬─────┬─────┬─────┐      │
               \      \    │└─────┴─────┴─────┴─────┴─────┴─────┘      │
    ┌────────┬──\──────\───┼────────────────────────────────────┐ 10500│
    │        │  ┌\──┐ ┌─\─┐└───────┐                            │      │
    │        │  └───┘ └───┘        │                            │      │
    ├─────┼──┴─────────────────────┼────────────────────────────┘      │
    │     │           О     ┌─────┬┴────┬─────┬─────┬─────┬─────┐      │
    │     │5       6 /      └─────┴─────┴─────┴─────┴─────┴─────┤      │
    │     └─       _/                                           │      │
    │                    ┌──┐  О  ┌──┐                          │      \/
    │                    └/─┘  │  └─\┴──────────────────────────┼───────
    │                    /7    │8    \ 9                        │
    │                   /__    └─     \_                        │
    │                                     32000                 │
    │<─────────────────────────────────────────────────────────>│
```


<div align="center">

<a id="p100188"></a>Планировка рабочего места котельщика для сборки<br>
и прихватки кольцевых швов обечаек

</div>


<a id="p100189"></a>1 - стеллаж для хранения обечаек; 2 - роликовый стенд; 3 - ящик для электродов; 4 - ящик для огарков; 5 - станок для сборки обечаек; 6 - стул; 7 - тумбочка; 8 - стойка с цветной сигнальной лампочкой для вызова внутрицехового транспорта; 9 - мусоросборник.


#### <a id="p100190"></a>3.9 Согласно принятым схемам предусматривается:

<a id="p100191"></a>3.9.1. Обеспечение минимально необходимых расстояний передвижения слесарей котельных работ в процессе работы в пределах рабочей зоны от 2 до 10 м в зависимости от габаритов деталей.
<a id="p100192"></a>3.9.2. Обслуживание рабочих мест котельных работ производится вспомогательными рабочими, обслуживающими производство (доставка заготовок, оснастки, технический контроль и т.п.)

##### <a id="p100193"></a>3.9.3 Выполнение в положении сидя или стоя (сверху или снизу).



### 4. <a id="p100194"></a>НОРМАТИВНАЯ ЧАСТЬ



#### <a id="p100195"></a>Раздел 1. НОРМАТИВЫ ПОДГОТОВИТЕЛЬНО-ЗАКЛЮЧИТЕЛЬНОГО ВРЕМЕНИ И НОРМАТИВЫ ШТУЧНОГО ВРЕМЕНИ НА УСТАНОВОЧНЫЕ РАБОТЫ



<table>
<colgroup><col width="8%"><col width="43%"><col width="9%"><col width="9%"><col width="3%"><col width="14%"><col width="14%"></colgroup>
<tr><td colspan="4" rowspan="2">Подготовительно-заключительное время</td><td colspan="3">Правка, гибка, сборка</td></tr>
<tr><td colspan="3">Карта 1</td></tr>
<tr><td colspan="7">Состав подготовительно-заключительного времени</td></tr>
<tr><td colspan="7">1. Получение сменного задания, наряда, чертежей, технологической документации и пр.</td></tr>
<tr><td colspan="7">2. Ознакомление с технической документацией.</td></tr>
<tr><td colspan="7">3. Получение инструмента, приспособлений.</td></tr>
<tr><td colspan="7">4. Подготовка рабочего места.</td></tr>
<tr><td colspan="7">5. Сдача технологической документации, инструмента, приспособлений.</td></tr>
<tr><td colspan="7">6. Сдача готовой продукции.</td></tr>
<tr><td rowspan="2">N позиции</td><td colspan="2" rowspan="2">Наименование показателей</td><td colspan="4">Степень сложности выполнения работы</td></tr>
<tr><td colspan="2">простая</td><td>средняя</td><td>сложная</td></tr>
<tr><td>1.</td><td colspan="2">Подготовительно-заключительное время на одно задание, Т, мин.</td><td colspan="2">8</td><td>11</td><td>13</td></tr>
<tr><td>2.</td><td colspan="2">То же, в процентах от нормы штучного времени, К 2</td><td colspan="2">2,6</td><td>2,9</td><td>3,6</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td colspan="2">а</td><td>б</td><td>в</td></tr>
</table>


<a id="p100209"></a>При работе в вальцах с подкладным листом к поз. 1 добавлять время на установку и снятие подкладного листа по поз. 3.


<table>
<colgroup><col width="8%"><col width="43%"><col width="9%"><col width="12%"><col width="14%"><col width="14%"></colgroup>
<tr><td colspan="3" rowspan="3"></td><td colspan="3">Длина подкладного листа, мм, до</td></tr>
<tr><td>2000</td><td>4500</td><td>8000</td></tr>
<tr><td colspan="3">Время Т, мин.</td></tr>
<tr><td>3.</td><td colspan="2">Установка подкладного листа в вальцы и снятие его</td><td>2</td><td>3</td><td>5</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td></tr>
</table>


<a id="p100213"></a>Характеристика степени сложности выполняемой работы.
<a id="p100214"></a>Простая. Правка деталей на плите, в вальцах и под прессом, установка мелких деталей под сварку и т.п.
<a id="p100215"></a>Средняя. Гибка в вальцах обечаек, полуобечаек, колец, полуколец, калибровка, сборка продольных стыков обечаек, сборка фланцев из секторов и т.п.
<a id="p100216"></a>Сложная. Сборка днищ из лепестков, сборка корпусов из обечаек, установка штуцеров на корпус, установка лап и опор, сборка днищ с корпусом и т.д.
<a id="p100217"></a>*Примечание.* При задании, рассчитанном на смену, подготовительно-заключительное время Тпз берется в минутах, а на период свыше одной смены - в процентах от нормы штучного времени.


<table>
<colgroup><col width="11%"><col width="23%"><col width="9%"><col width="8%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="7" rowspan="2">Установка и снятие деталей на верстак или стол станка вручную</td><td colspan="4">Установочные работы</td></tr>
<tr><td colspan="4">Карта 2</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">Установка:</td></tr>
<tr><td colspan="11">1. Взять деталь, узел.</td></tr>
<tr><td colspan="11">2. Установить на верстак или стол станка.</td></tr>
<tr><td colspan="11">Снятие:</td></tr>
<tr><td colspan="11">1. Взять деталь, узел.</td></tr>
<tr><td colspan="11">2. Снять с верстака или стола станка, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Наименование операции</td><td colspan="8">Масса М, кг, до</td></tr>
<tr><td>0,5</td><td>1,0</td><td>2,0</td><td>4,0</td><td>7,0</td><td>10,0</td><td>15,0</td><td>20</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>1.</td><td colspan="2">Установка</td><td>0,090</td><td>0,11</td><td>0,140</td><td>0,17</td><td>0,20</td><td>0,23</td><td>0,26</td><td>0,29</td></tr>
<tr><td>2.</td><td colspan="2">Снятие</td><td>0,063</td><td>0,08</td><td>0,097</td><td>0,12</td><td>0,14</td><td>0,16</td><td>0,18</td><td>0,20</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p100231"></a>Примечание: Работа выполняется одним человеком:

                                    0,31
<a id="p100232"></a>                       Т = 0,113 х М     поз. 1;

                                    0,31
<a id="p100233"></a>                       Т = 0,078 х М     поз. 2.


<table>
<colgroup><col width="6%"><col width="9%"><col width="11%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="11" rowspan="2">Установка деталей, узлов на плиту или роликовые опоры краном</td><td colspan="6">Установочные работы</td></tr>
<tr><td colspan="6">Карта 3, лист 1</td></tr>
<tr><td colspan="17">Содержание работы</td></tr>
<tr><td colspan="17">1. Застропить деталь, узел.</td></tr>
<tr><td colspan="17">2. Установить на плиту или роликовые опоры.</td></tr>
<tr><td colspan="17">3. Отстропить деталь, узел.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Тип деталей,</td><td rowspan="3">Место установки</td><td colspan="14">Масса М, т, до</td></tr>
<tr><td rowspan="2">узлов</td><td>0,1</td><td>0,2</td><td>0,3</td><td>0,5</td><td>0,8</td><td>1,0</td><td>2,0</td><td>3,0</td><td>5,0</td><td>10</td><td>15</td><td>20</td><td>30</td><td>50</td></tr>
<tr><td colspan="14">Время на установку одной детали, узла Т, чел.-мин.</td></tr>
<tr><td>1</td><td>Плоские</td><td>на плиту</td><td>1,36</td><td>1,65</td><td>1,85</td><td>2,14</td><td>2,44</td><td>2,60</td><td>3,15</td><td>3,54</td><td>4,08</td><td>4,95</td><td>5,55</td><td>6,00</td><td>6,74</td><td>7,77</td></tr>
<tr><td>2</td><td rowspan="2">Объемные</td><td>на плиту</td><td>1,50</td><td>1,82</td><td>2,04</td><td>2,35</td><td>2,68</td><td>2,86</td><td>3,47</td><td>3,89</td><td>4,49</td><td>5,45</td><td>6,10</td><td>6,60</td><td>7,41</td><td>8,55</td></tr>
<tr><td>3</td><td>на рожковые опоры</td><td>1,64</td><td>1,99</td><td>2,23</td><td>2,57</td><td>2,93</td><td>3,12</td><td>3,79</td><td>4,24</td><td>4,90</td><td>5,94</td><td>6,66</td><td>7,22</td><td>8,09</td><td>9,33</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>


<a id="p100245"></a>Примечания: 1. Нормативами предусмотрена строповка двумя крюками и перемещение крана в рабочей зоне котельщика.


<table>
<colgroup><col width="67%"><col width="33%"></colgroup>
<tr><td rowspan="2">Установка деталей, узлов на плиту или роликовые опоры краном</td><td>Установочные работы</td></tr>
<tr><td>Карта 3, лист 2</td></tr>
</table>


2. <a id="p100248"></a>При измененных условиях установки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="15%"><col width="14%"><col width="8%"><col width="8%"><col width="7%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="6%"><col width="8%"><col width="9%"></colgroup>
<tr><td>Факторы, влияющие на</td><td>Установка и перемещение</td><td rowspan="2">Снятие деталей</td><td colspan="3">Установка</td><td colspan="6">Способ строповки</td></tr>
<tr><td>изменение нормы времени</td><td>деталей, узлов</td><td>двумя кранами</td><td>одним краном</td><td>тельфером</td><td>к-во строп</td><td>крюками</td><td>тросом</td><td>цепью</td><td>струбцинами с болтами</td><td>крюком крана за рым-болт</td></tr>
<tr><td rowspan="2">Коэффициент</td><td rowspan="2">1,0</td><td rowspan="2">0,9</td><td rowspan="2">1,5</td><td rowspan="2">1,0</td><td rowspan="2">0,8</td><td>2</td><td>1,0</td><td>2,5</td><td>2,0</td><td>1,5</td><td>-</td></tr>
<tr><td>1</td><td>0,6</td><td>1,5</td><td>1,1</td><td>0,9</td><td>0,9</td></tr>
</table>


3. <a id="p100252"></a>Работа выполняется бригадой из двух человек:

               0,28                     0,28                     0,28
<a id="p100253"></a>    Т = 2,6 х М     поз. 1; Т = 2,86 х М     поз. 2; Т = 3,12 х М     поз. 3.


<table>
<colgroup><col width="20%"><col width="11%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="4%"><col width="5%"><col width="9%"><col width="9%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Перемещение деталей, узлов краном</td><td colspan="4">Установочные работы</td></tr>
<tr><td colspan="4">Карта 4, лист 1</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">1. Застропить деталь или узел.</td></tr>
<tr><td colspan="11">2. Переместить к месту сборки.</td></tr>
<tr><td colspan="11">3. Отстропить деталь, узел.</td></tr>
<tr><td rowspan="3">Способ застропки</td><td>Кол-во строп,</td><td colspan="9">Расстояние перемещения груза краном L, м, до</td></tr>
<tr><td rowspan="2">n</td><td>15</td><td>20</td><td>30</td><td>50</td><td colspan="2">75</td><td>100</td><td>150</td><td>200</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>(рисунок не приводится)</td><td>1</td><td>0,89</td><td>1,10</td><td>1,47</td><td>2,14</td><td colspan="2">2,88</td><td>3,55</td><td>4,77</td><td>5,88</td></tr>
<tr><td rowspan="3">крюками</td><td>2</td><td>1,07</td><td>1,32</td><td>1,77</td><td>2,58</td><td colspan="2">3,47</td><td>4,28</td><td>5,75</td><td>7,09</td></tr>
<tr><td>3</td><td>1,19</td><td>1,47</td><td>1,98</td><td>2,88</td><td colspan="2">3,87</td><td>4,77</td><td>6,42</td><td>7,92</td></tr>
<tr><td>4</td><td>1,29</td><td>1,59</td><td>2,14</td><td>3,11</td><td colspan="2">4,18</td><td>5,16</td><td>6,93</td><td>8,55</td></tr>
<tr><td>(рисунок не приводится)</td><td>1</td><td>1,84</td><td>2,08</td><td>2,48</td><td>3,09</td><td colspan="2">3,67</td><td>4,16</td><td>4,95</td><td>5,60</td></tr>
<tr><td>тросом</td><td>2</td><td>2,65</td><td>3,00</td><td>3,58</td><td>4,45</td><td colspan="2">5,30</td><td>6,00</td><td>7,15</td><td>8,09</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="20%"><col width="11%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"><col width="3%"><col width="7%"><col width="9%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Перемещение деталей, узлов краном</td><td colspan="4">Установочные работы</td></tr>
<tr><td colspan="4">Карта 4, лист 2</td></tr>
<tr><td rowspan="3">Способ застропки</td><td>Кол-во строп,</td><td colspan="9">Расстояние перемещения груза краном L, м, до</td></tr>
<tr><td rowspan="2">n</td><td>15</td><td>20</td><td>30</td><td>50</td><td colspan="2">75</td><td>100</td><td>150</td><td>200</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>(рисунок не приводится)</td><td>1</td><td>1,57</td><td>1,89</td><td>2,45</td><td>3,40</td><td colspan="2">4,41</td><td>5,30</td><td>6,87</td><td>8,25</td></tr>
<tr><td>цепью</td><td>2</td><td>2,24</td><td>2,69</td><td>4,49</td><td>4,84</td><td colspan="2">6,27</td><td>7,54</td><td>9,78</td><td>11,8</td></tr>
<tr><td>(рисунок не приводится)</td><td>1</td><td>1,26</td><td>1,43</td><td>1,71</td><td>2,12</td><td colspan="2">2,53</td><td>2,86</td><td>3,41</td><td>3,86</td></tr>
<tr><td>струбцинами с болтами</td><td>2</td><td>1,54</td><td>1,74</td><td>2,07</td><td>2,58</td><td colspan="2">3,07</td><td>3,47</td><td>4,14</td><td>4,68</td></tr>
<tr><td>(рисунок не приводится) крюком крана за рым-болт</td><td>1</td><td>0,86</td><td>1,07</td><td>1,45</td><td>2,12</td><td colspan="2">2,90</td><td>3,57</td><td>4,80</td><td>6,00</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="66%"><col width="34%"></colgroup>
<tr><td rowspan="2">Перемещение деталей, узлов краном</td><td>Установочные работы</td></tr>
<tr><td>Карта 4, лист 3</td></tr>
</table>


<a id="p100278"></a>Примечания: 1. При отсутствии просвета для отстроповки тросом к времени по карте на каждый трос добавлять 0,5 мин.
2. <a id="p100279"></a>Работа выполняется бригадой из двух человек:

                               0,27    0,73
<a id="p100280"></a>                  Т = 0,123 х n     х L     - крюками;

                               0,53    0,43
<a id="p100281"></a>                  Т = 0,574 х n     х L     - тросом;

                               0,51    0,64
<a id="p100282"></a>                  Т = 0,278 х n     х L     - цепью;

                               0,28    0,43
<a id="p100283"></a>                  Т = 0,395 х n     х L     - струбциной с болтами;

                               0,75
<a id="p100284"></a>                  Т = 0,113 х L     - крюком за рым-болт.


<table>
<colgroup><col width="11%"><col width="27%"><col width="15%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="6" rowspan="2">Кантовка деталей, узлов вручную</td><td colspan="4">Установочные работы</td></tr>
<tr><td colspan="4">Карта 5</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Взять деталь, узел.</td></tr>
<tr><td colspan="10">2. Повернуть в горизонтальной или вертикальной плоскости.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Характер работы</td><td>Угол поворота</td><td colspan="7">Масса М, кг, до</td></tr>
<tr><td rowspan="2">альфа, град., до</td><td>1</td><td>3</td><td>5</td><td>8</td><td>12</td><td>16</td><td>20</td></tr>
<tr><td colspan="7">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>Поворачивание детали, узла в</td><td>90</td><td>0,09</td><td>0,10</td><td>0,11</td><td>0,13</td><td>0,14</td><td>0,16</td><td>0,18</td></tr>
<tr><td>2</td><td>горизонтальной плоскости</td><td>180</td><td>0,12</td><td>0,14</td><td>0,15</td><td>0,17</td><td>0,19</td><td>0,21</td><td>0,24</td></tr>
<tr><td>3</td><td>Поворачивание детали, узла в</td><td>90</td><td>0,13</td><td>0,15</td><td>0,16</td><td>0,18</td><td>0,20</td><td>0,23</td><td>0,25</td></tr>
<tr><td>4</td><td>вертикальной плоскости</td><td>180</td><td>0,19</td><td>0,22</td><td>0,23</td><td>0,27</td><td>0,30</td><td>0,33</td><td>0,38</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td></tr>
</table>


<a id="p100296"></a>Примечания: 1. При измененных условиях приведенное в нормативной карте время применяется с коэффициентами:


<a id="p100299"></a><a id="p100300"></a><a id="p100301"></a><a id="p100302"></a><a id="p100303"></a>

<table>
<colgroup><col width="45%"><col width="27%"><col width="28%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="2">Кантовка</td></tr>
<tr><td>плоских деталей</td><td>объемных деталей</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>0,9</td></tr>
<tr><td>2. Работа выполняется одним человеком:</td><td></td><td></td></tr>
<tr><td>0,4 Т = 0,0148 х альфа х М</td><td>0,14 при М &lt;= 8 кг</td><td>поз. 1...2;</td></tr>
<tr><td>0,4 Т = 0,00811 х альфа х М</td><td>0,43 при М &gt; 8 кг</td><td>поз. 1...2;</td></tr>
<tr><td>0,55 Т = 0,0107 х альфа х М</td><td>0,14 при М &lt;= 8 кг</td><td>поз. 3...4;</td></tr>
<tr><td>0,55 Т = 0,00585 х альфа х М</td><td>0,43 при М &gt; 8 кг</td><td>поз. 3...4.</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="19%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12">Кантовка деталей, узлов краном Установочные работы</td></tr>
<tr><td colspan="12">Карта 6, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Застропить деталь, узел.</td></tr>
<tr><td colspan="12">2. Повернуть в горизонтальной или вертикальной плоскости.</td></tr>
<tr><td colspan="12">3. Отстропить деталь, узел.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Характер работы</td><td>Угол поворота</td><td colspan="9">Масса М, кг, до</td></tr>
<tr><td>альфа, град.,</td><td>0,1</td><td>0,25</td><td>0,5</td><td>1</td><td>2</td><td>3</td><td>5</td><td>10</td><td>15</td></tr>
<tr><td>до</td><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="2">Поворачивание детали, узла в горизонтальной плоскости</td><td>90</td><td>1,47</td><td>1,62</td><td>1,74</td><td>1,86</td><td>2,24</td><td>2,50</td><td>2,87</td><td>3,46</td><td>3,86</td></tr>
<tr><td>2</td><td>180</td><td>1,91</td><td>2,09</td><td>2,24</td><td>2,40</td><td>2,90</td><td>3,23</td><td>3,71</td><td>4,47</td><td>5,00</td></tr>
<tr><td>3</td><td>Поворачивание детали, узла</td><td>90</td><td>1,57</td><td>1,73</td><td>1,85</td><td>1,98</td><td>2,39</td><td>2,67</td><td>3,06</td><td>3,69</td><td>4,12</td></tr>
<tr><td>4</td><td>в вертикальной плоскости</td><td>180</td><td>2,03</td><td>2,23</td><td>2,39</td><td>2,56</td><td>3,09</td><td>3,45</td><td>3,96</td><td>4,77</td><td>5,32</td></tr>
<tr><td>5</td><td>Поворот детали, узла</td><td>90</td><td>1,07</td><td>1,20</td><td>1,32</td><td>1,44</td><td>1,74</td><td>1,94</td><td>2,23</td><td>2,68</td><td>2,99</td></tr>
<tr><td>6</td><td>в роликовых опорах</td><td>180</td><td>1,27</td><td>1,43</td><td>1,57</td><td>1,71</td><td>2,07</td><td>2,31</td><td>2,65</td><td>3,19</td><td>3,56</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p100318"></a>Примечания: 1. Нормативами предусмотрена строповка двумя крюками.
2. <a id="p100319"></a>При измененных условиях кантовки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="12%"><col width="8%"><col width="9%"><col width="8%"><col width="8%"><col width="6%"><col width="7%"><col width="6%"><col width="7%"><col width="5%"><col width="5%"><col width="6%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="14">Кантовка деталей, узлов краном Установочные работы</td></tr>
<tr><td colspan="14">Карта 6, лист 2</td></tr>
<tr><td>Факторы, влияющие на</td><td colspan="7">Кантовка</td><td colspan="6">Строповка деталей, узлов</td></tr>
<tr><td>изменение нормы времени</td><td>плоских деталей</td><td>объемных деталей</td><td>в роликовых опорах</td><td>в механизированных опорах</td><td>двумя кранами</td><td>одним краном</td><td>тельфером</td><td>количество строп</td><td>крюками</td><td>тросом</td><td>цепью</td><td>струбцинами с болтами</td><td>крюком крана за рымболт</td></tr>
<tr><td rowspan="2">Коэффициент</td><td rowspan="2">1,0</td><td rowspan="2">0,9</td><td rowspan="2">1,0</td><td rowspan="2">0,55</td><td rowspan="2">1,5</td><td rowspan="2">1,0</td><td rowspan="2">0,8</td><td>2</td><td>1,0</td><td>2,5</td><td>2,0</td><td>1,5</td><td>-</td></tr>
<tr><td>1</td><td>0,6</td><td>1,5</td><td>1,1</td><td>0,9</td><td>0,9</td></tr>
</table>


3. <a id="p100325"></a>Работа выполняется бригадой из двух человек:

                        0,37    0,1
<a id="p100326"></a>       Т = 0,352 х альфа     х М     при М <= 1 т   поз. 1...2;

                        0,37    0,27
<a id="p100327"></a>       Т = 0,352 х альфа     х М     при М > 1 т    поз. 1...2;

                        0,37    0,1
<a id="p100328"></a>       Т = 0,375 х альфа     х М     при М <= 1 т   поз. 3...4;

                        0,37    0,27
<a id="p100329"></a>       Т = 0,375 х альфа     х М     при М > 1 т    поз. 3...4;

                        0,25    0,13
<a id="p100330"></a>       Т = 0,468 х альфа     х М     при М <= 1 т   поз. 5...6;

                        0,25    0,27
<a id="p100331"></a>       Т = 0,468 х альфа     х М     при М > 1 т    поз. 5...6.


#### <a id="p100332"></a>Раздел 2. НОРМАТИВЫ ШТУЧНОГО ВРЕМЕНИ НА ПРАВКУ ДЕТАЛЕЙ



<table>
<colgroup><col width="11%"><col width="14%"><col width="14%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="8" rowspan="2">Предварительная правка листов в пяти-, семивалковых вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 7, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Подать лист к вальцам, установить между валками. (рисунок не</td></tr>
<tr><td colspan="12">2. Выправить лист, проверить на точность линейкой. приводится)</td></tr>
<tr><td colspan="12">3. Снять выправленный лист, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина листа В,</td><td>Длина листа L,</td><td colspan="9">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">мм, до</td><td rowspan="2">мм, до</td><td>4</td><td>6</td><td>8</td><td>12</td><td>18</td><td>24</td><td>32</td><td>40</td><td>50</td></tr>
<tr><td colspan="9">Время на лист Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="5">1500</td><td>2000</td><td>2,5</td><td>2,9</td><td>3,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>3000</td><td>3,2</td><td>3,6</td><td>3,9</td><td>4,5</td><td>5,1</td><td>5,6</td><td>6,1</td><td>6,5</td><td>7,0</td></tr>
<tr><td>3</td><td>4500</td><td>4,0</td><td>4,6</td><td>5,0</td><td>5,7</td><td>6,5</td><td>7,1</td><td>7,7</td><td>8,3</td><td>8,9</td></tr>
<tr><td>4</td><td>6000</td><td>4,8</td><td>5,4</td><td>5,9</td><td>6,7</td><td>7,6</td><td>8,3</td><td>9,1</td><td>9,8</td><td>10,5</td></tr>
<tr><td>5</td><td>8000</td><td>5,7</td><td>6,4</td><td>7,0</td><td>7,9</td><td>9,0</td><td>9,9</td><td>10,8</td><td>11,6</td><td>12,4</td></tr>
<tr><td>6</td><td rowspan="3">2000</td><td>4500</td><td>4,7</td><td>5,3</td><td>5,8</td><td>6,6</td><td>7,4</td><td>8,1</td><td>8,8</td><td>9,5</td><td>10,2</td></tr>
<tr><td>7</td><td>6000</td><td>5,5</td><td>6,2</td><td>6,8</td><td>7,7</td><td>8,8</td><td>9,6</td><td>10,5</td><td>11,2</td><td>12,0</td></tr>
<tr><td>8</td><td>8000</td><td>6,5</td><td>7,4</td><td>8,1</td><td>9,1</td><td>10,4</td><td>11,3</td><td>12,3</td><td>13,3</td><td>14,2</td></tr>
<tr><td>9</td><td rowspan="4">2600</td><td>4500</td><td>-</td><td>-</td><td>6,6</td><td>7,4</td><td>8,4</td><td>9,2</td><td>10,1</td><td>10,8</td><td>11,5</td></tr>
<tr><td>10</td><td>6000</td><td>-</td><td>-</td><td>7,7</td><td>8,8</td><td>9,9</td><td>10,9</td><td>11,9</td><td>12,7</td><td>13,6</td></tr>
<tr><td>11</td><td>8000</td><td>-</td><td>-</td><td>9,1</td><td>10,4</td><td>11,8</td><td>12,8</td><td>14,0</td><td>15,1</td><td>16,1</td></tr>
<tr><td>12</td><td>9000</td><td>-</td><td>-</td><td>9,8</td><td>11,1</td><td>12,6</td><td>13,8</td><td>15,0</td><td>16,1</td><td>17,3</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="72%"><col width="28%"></colgroup>
<tr><td rowspan="2">Предварительная правка листов в пяти-, семивалковых вальцах</td><td>Правка</td></tr>
<tr><td>Карта 7, лист 2</td></tr>
</table>


<a id="p100355"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="11%"><col width="9%"><col width="11%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="5%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="3">Материал</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="5">К-во листов в пакете</td></tr>
<tr><td>нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>1</td><td>2</td><td>3</td><td>4</td><td>5</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,1</td><td>1,0</td><td>0,9</td><td>1,0</td><td>0,8</td><td>0,6</td><td>0,45</td><td>0,4</td></tr>
</table>


2. <a id="p100358"></a>Работа выполняется бригадой из двух человек:

                                   0,48    0,58    0,31
<a id="p100359"></a>                     Т = 0,0006 х В     х L     х h    .


<table>
<colgroup><col width="11%"><col width="14%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="5%"><col width="7%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Правка листов в пяти-, семивалковых вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 8, лист 1</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">1. Подать лист к вальцам, установить лист между (рисунок не валками. приводится)</td></tr>
<tr><td colspan="13">2. Выправить лист, проверить на точность линейкой.</td></tr>
<tr><td colspan="13">3. Снять выправленный лист, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина листа</td><td>Толщина листа h,</td><td colspan="10">Длина листа L, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">мм, до</td><td>700</td><td>1000</td><td>1400</td><td>2000</td><td>3000</td><td colspan="2">4200</td><td>6000</td><td>8600</td><td>12000</td></tr>
<tr><td colspan="10">Время на лист Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="6">500</td><td>4</td><td>0,69</td><td>0,85</td><td>1,05</td><td>1,30</td><td>1,66</td><td colspan="2">2,04</td><td>2,54</td><td>3,17</td><td>3,88</td></tr>
<tr><td>2</td><td>8</td><td>0,82</td><td>1,02</td><td>1,25</td><td>1,56</td><td>1,99</td><td colspan="2">2,45</td><td>3,05</td><td>3,79</td><td>4,65</td></tr>
<tr><td>3</td><td>12</td><td>0,91</td><td>1,13</td><td>1,37</td><td>1,72</td><td>2,21</td><td colspan="2">2,71</td><td>3,37</td><td>4,20</td><td>5,14</td></tr>
<tr><td>4</td><td>18</td><td>1,01</td><td>1,26</td><td>1,54</td><td>1,92</td><td>2,46</td><td colspan="2">3,02</td><td>3,75</td><td>4,67</td><td>5,73</td></tr>
<tr><td>5</td><td>24</td><td>1,20</td><td>1,49</td><td>1,83</td><td>2,27</td><td>2,91</td><td colspan="2">3,57</td><td>4,44</td><td>5,53</td><td>6,77</td></tr>
<tr><td>6</td><td>32</td><td>1,37</td><td>1,70</td><td>2,09</td><td>2,60</td><td>3,33</td><td colspan="2">4,09</td><td>5,07</td><td>6,33</td><td>7,76</td></tr>
<tr><td>7</td><td rowspan="7">700</td><td>4</td><td>0,81</td><td>1,01</td><td>1,24</td><td>1,54</td><td>1,97</td><td colspan="2">2,42</td><td>3,01</td><td>3,74</td><td>4,59</td></tr>
<tr><td>8</td><td>8</td><td>0,97</td><td>1,20</td><td>1,48</td><td>1,84</td><td>2,35</td><td colspan="2">2,89</td><td>3,59</td><td>4,47</td><td>5,48</td></tr>
<tr><td>9</td><td>12</td><td>1,08</td><td>1,34</td><td>1,64</td><td>2,04</td><td>2,62</td><td colspan="2">3,21</td><td>3,99</td><td>4,97</td><td>6,09</td></tr>
<tr><td>10</td><td>18</td><td>1,20</td><td>1,49</td><td>1,83</td><td>2,27</td><td>2,91</td><td colspan="2">3,57</td><td>4,44</td><td>5,53</td><td>6,77</td></tr>
<tr><td>11</td><td>24</td><td>1,41</td><td>1,76</td><td>2,16</td><td>2,68</td><td>3,44</td><td colspan="2">4,22</td><td>5,24</td><td>6,53</td><td>8,00</td></tr>
<tr><td>12</td><td>32</td><td>1,62</td><td>2,01</td><td>2,47</td><td>3,08</td><td>3,94</td><td colspan="2">4,84</td><td>6,01</td><td>7,49</td><td>9,17</td></tr>
<tr><td>13</td><td>40</td><td>1,80</td><td>2,24</td><td>2,75</td><td>3,42</td><td>4,37</td><td colspan="2">5,37</td><td>6,68</td><td>8,32</td><td>10,19</td></tr>
<tr><td>14</td><td rowspan="4">1000</td><td>4</td><td>0,97</td><td>1,20</td><td>1,48</td><td>1,84</td><td>2,35</td><td colspan="2">2,89</td><td>3,59</td><td>4,47</td><td>5,48</td></tr>
<tr><td>15</td><td>8</td><td>1,16</td><td>1,44</td><td>1,77</td><td>2,20</td><td>2,81</td><td colspan="2">3,46</td><td>4,30</td><td>5,78</td><td>6,56</td></tr>
<tr><td>16</td><td>12</td><td>1,29</td><td>1,60</td><td>1,97</td><td>2,45</td><td>3,13</td><td colspan="2">3,85</td><td>4,78</td><td>5,95</td><td>7,30</td></tr>
<tr><td>17</td><td>18</td><td>1,43</td><td>1,78</td><td>2,18</td><td>2,71</td><td>3,48</td><td colspan="2">4,27</td><td>5,30</td><td>6,61</td><td>8,10</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="12%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Правка листов в пяти-, семивалковых вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 8, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина листа</td><td>Толщина листа h,</td><td colspan="10">Длина листа L, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">мм, до</td><td>700</td><td>1000</td><td>1400</td><td>2000</td><td>3000</td><td colspan="2">4200</td><td>6000</td><td>8600</td><td>12000</td></tr>
<tr><td colspan="10">Время на лист Т, чел.-мин.</td></tr>
<tr><td>18</td><td rowspan="4">1000</td><td>24</td><td>1,69</td><td>2,10</td><td>2,58</td><td>3,21</td><td>4,11</td><td colspan="2">5,05</td><td>6,27</td><td>7,81</td><td>9,57</td></tr>
<tr><td>19</td><td>32</td><td>1,94</td><td>2,41</td><td>2,96</td><td>3,67</td><td>4,70</td><td colspan="2">5,78</td><td>7,18</td><td>8,94</td><td>10,96</td></tr>
<tr><td>20</td><td>40</td><td>2,15</td><td>2,68</td><td>3,29</td><td>4,09</td><td>5,23</td><td colspan="2">6,43</td><td>7,99</td><td>9,95</td><td>12,19</td></tr>
<tr><td>21</td><td>56</td><td>2,52</td><td>3,13</td><td>3,84</td><td>4,78</td><td>6,12</td><td colspan="2">7,51</td><td>9,34</td><td>11,63</td><td>14,25</td></tr>
<tr><td>22</td><td rowspan="9">1500</td><td>4</td><td>1,19</td><td>1,47</td><td>1,81</td><td>2,25</td><td>2,88</td><td colspan="2">3,54</td><td>4,40</td><td>5,48</td><td>6,71</td></tr>
<tr><td>23</td><td>8</td><td>1,42</td><td>1,76</td><td>2,17</td><td>2,69</td><td>3,45</td><td colspan="2">4,23</td><td>5,26</td><td>6,56</td><td>8,03</td></tr>
<tr><td>24</td><td>12</td><td>1,58</td><td>1,96</td><td>2,41</td><td>2,99</td><td>3,83</td><td colspan="2">4,71</td><td>5,85</td><td>7,29</td><td>8,93</td></tr>
<tr><td>25</td><td>18</td><td>1,75</td><td>2,18</td><td>2,67</td><td>3,32</td><td>4,25</td><td colspan="2">5,22</td><td>6,49</td><td>8,09</td><td>9,91</td></tr>
<tr><td>26</td><td>24</td><td>2,07</td><td>2,58</td><td>3,16</td><td>3,93</td><td>5,03</td><td colspan="2">6,18</td><td>7,68</td><td>9,57</td><td>11,73</td></tr>
<tr><td>27</td><td>32</td><td>2,37</td><td>2,95</td><td>3,62</td><td>4,50</td><td>5,76</td><td colspan="2">7,07</td><td>8,79</td><td>10,95</td><td>13,42</td></tr>
<tr><td>28</td><td>40</td><td>2,64</td><td>3,28</td><td>4,03</td><td>5,00</td><td>6,41</td><td colspan="2">7,87</td><td>9,78</td><td>12,18</td><td>14,93</td></tr>
<tr><td>29</td><td>56</td><td>3,09</td><td>3,84</td><td>4,72</td><td>5,86</td><td>7,51</td><td colspan="2">9,22</td><td>11,46</td><td>14,27</td><td>17,48</td></tr>
<tr><td>30</td><td>75</td><td>3,54</td><td>4,40</td><td>5,40</td><td>6,72</td><td>8,60</td><td colspan="2">10,56</td><td>13,13</td><td>16,35</td><td>20,04</td></tr>
<tr><td>31</td><td rowspan="9">2200</td><td>4</td><td>1,44</td><td>1,78</td><td>2,19</td><td>2,72</td><td>3,49</td><td colspan="2">4,28</td><td>5,32</td><td>6,63</td><td>8,13</td></tr>
<tr><td>32</td><td>8</td><td>1,72</td><td>2,14</td><td>2,62</td><td>3,26</td><td>4,18</td><td colspan="2">5,13</td><td>6,37</td><td>7,94</td><td>9,73</td></tr>
<tr><td>33</td><td>12</td><td>1,91</td><td>2,37</td><td>2,91</td><td>3,62</td><td>4,64</td><td colspan="2">5,69</td><td>7,08</td><td>8,82</td><td>10,80</td></tr>
<tr><td>34</td><td>18</td><td>2,12</td><td>2,64</td><td>3,24</td><td>4,02</td><td>5,15</td><td colspan="2">6,33</td><td>7,87</td><td>9,80</td><td>12,00</td></tr>
<tr><td>35</td><td>24</td><td>2,51</td><td>3,12</td><td>3,84</td><td>4,77</td><td>6,10</td><td colspan="2">7,50</td><td>9,32</td><td>11,61</td><td>14,22</td></tr>
<tr><td>36</td><td>32</td><td>2,87</td><td>3,57</td><td>4,38</td><td>5,45</td><td>6,98</td><td colspan="2">8,57</td><td>10,65</td><td>13,26</td><td>16,25</td></tr>
<tr><td>37</td><td>40</td><td>3,19</td><td>3,97</td><td>4,87</td><td>6,06</td><td>7,76</td><td colspan="2">9,52</td><td>11,84</td><td>14,75</td><td>18,07</td></tr>
<tr><td>38</td><td>56</td><td>3,74</td><td>4,64</td><td>5,70</td><td>7,09</td><td>9,08</td><td colspan="2">11,15</td><td>13,86</td><td>17,26</td><td>21,15</td></tr>
<tr><td>39</td><td>75</td><td>4,29</td><td>5,33</td><td>6,55</td><td>8,14</td><td>10,43</td><td colspan="2">12,80</td><td>15,91</td><td>19,82</td><td>24,29</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="12%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Правка листов в пяти-, семивалковых вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 8, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина листа В,</td><td>Толщина листа h,</td><td colspan="10">Длина листа L, мм, до</td></tr>
<tr><td rowspan="2">мм, до</td><td rowspan="2">мм, до</td><td>700</td><td>1000</td><td>1400</td><td>2000</td><td>3000</td><td colspan="2">4200</td><td>6000</td><td>8600</td><td>12000</td></tr>
<tr><td colspan="10">Время на лист Т, чел.-мин.</td></tr>
<tr><td>40</td><td rowspan="9">3200</td><td>4</td><td>1,73</td><td>2,15</td><td>2,64</td><td>3,28</td><td>4,20</td><td colspan="2">5,16</td><td>6,41</td><td>7,99</td><td>9,79</td></tr>
<tr><td>41</td><td>8</td><td>2,07</td><td>2,58</td><td>3,16</td><td>3,93</td><td>5,03</td><td colspan="2">6,18</td><td>7,68</td><td>9,57</td><td>11,73</td></tr>
<tr><td>42</td><td>12</td><td>2,30</td><td>2,86</td><td>3,51</td><td>4,36</td><td>5,59</td><td colspan="2">6,86</td><td>8,53</td><td>10,63</td><td>13,02</td></tr>
<tr><td>43</td><td>18</td><td>2,56</td><td>3,18</td><td>3,91</td><td>4,86</td><td>6,22</td><td colspan="2">7,64</td><td>9,50</td><td>11,83</td><td>14,50</td></tr>
<tr><td>44</td><td>24</td><td>3,03</td><td>3,77</td><td>4,62</td><td>5,75</td><td>7,36</td><td colspan="2">9,04</td><td>11,23</td><td>13,99</td><td>17,15</td></tr>
<tr><td>45</td><td>32</td><td>3,46</td><td>4,31</td><td>5,29</td><td>6,57</td><td>8,42</td><td colspan="2">10,34</td><td>12,85</td><td>16,00</td><td>19,61</td></tr>
<tr><td>46</td><td>40</td><td>3,85</td><td>4,79</td><td>5,88</td><td>7,31</td><td>9,36</td><td colspan="2">11,49</td><td>14,28</td><td>17,79</td><td>21,79</td></tr>
<tr><td>47</td><td>56</td><td>4,51</td><td>5,60</td><td>6,88</td><td>8,55</td><td>10,95</td><td colspan="2">13,45</td><td>16,72</td><td>20,83</td><td>25,52</td></tr>
<tr><td>48</td><td>75</td><td>5,17</td><td>6,43</td><td>7,89</td><td>9,81</td><td>12,57</td><td colspan="2">15,43</td><td>19,18</td><td>23,89</td><td>29,27</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p100424"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="12%"><col width="11%"><col width="11%"><col width="8%"><col width="5%"><col width="8%"><col width="5%"><col width="9%"><col width="12%"><col width="8%"><col width="9%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="3">Материал</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="4">Правка листов</td></tr>
<tr><td>нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>после сварки</td><td>после резки на гильотинных ножницах</td><td>двухсторонняя</td><td>односторонняя</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,1</td><td>1,0</td><td>0,9</td><td>1,2</td><td>1,0</td><td>1,4</td><td>1,0</td></tr>
</table>


2. <a id="p100427"></a>Работа выполняется бригадой из двух человек:

                            0,5    0,26    0,61
<a id="p100428"></a>            Т = 0,000392 х В    х h     х L     при h <= 18 мм;

                            0,5    0,47    0,61
<a id="p100429"></a>            Т = 0,000221 х В    х h     х L     при h > 18 мм.


<table>
<colgroup><col width="9%"><col width="16%"><col width="9%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Правка углового, круглого и квадратного проката на ролико- и вальцеправильных машинах</td><td colspan="3">Правка</td></tr>
<tr><td colspan="3">Карта 9, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Подать деталь на стол машины.</td></tr>
<tr><td colspan="12">2. Заправить деталь в валки (ролики) машины.</td></tr>
<tr><td colspan="12">3. Установить и отрегулировать валки (ролики) на размер.</td></tr>
<tr><td colspan="12">4. Выправить деталь, проверить на точность линейкой.</td></tr>
<tr><td colspan="12">5. Снять деталь, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид проката</td><td colspan="2">Номер или размер</td><td colspan="8">Длина детали L, мм, до</td></tr>
<tr><td colspan="2" rowspan="2">проката</td><td>1000</td><td>2000</td><td>3000</td><td>4300</td><td>6000</td><td>8000</td><td>10000</td><td>12000</td></tr>
<tr><td colspan="8">Время на деталь Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="7">(рисунок не приводится)</td><td rowspan="7">N</td><td>4</td><td>0,39</td><td>0,63</td><td>0,83</td><td>1,10</td><td>1,33</td><td>1,62</td><td>1,89</td><td>2,14</td></tr>
<tr><td>2</td><td>5</td><td>0,44</td><td>0,70</td><td>0,92</td><td>1,22</td><td>1,48</td><td>1,80</td><td>2,10</td><td>2,38</td></tr>
<tr><td>3</td><td>6</td><td>0,50</td><td>0,81</td><td>1,06</td><td>1,40</td><td>1,71</td><td>2,07</td><td>2,41</td><td>2,73</td></tr>
<tr><td>4</td><td>8</td><td>0,57</td><td>0,91</td><td>1,20</td><td>1,58</td><td>1,93</td><td>2,34</td><td>2,73</td><td>3,09</td></tr>
<tr><td>5</td><td>10</td><td>0,65</td><td>1,04</td><td>1,36</td><td>1,80</td><td>2,19</td><td>2,66</td><td>3,10</td><td>3,51</td></tr>
<tr><td>6</td><td>12</td><td>0,73</td><td>1,18</td><td>1,55</td><td>2,04</td><td>2,48</td><td>3,02</td><td>3,52</td><td>3,98</td></tr>
<tr><td>7</td><td>16</td><td>0,84</td><td>1,33</td><td>1,76</td><td>2,32</td><td>2,82</td><td>3,43</td><td>3,99</td><td>4,51</td></tr>
<tr><td>8</td><td rowspan="7">(рисунок не приводится)</td><td rowspan="7">Д, мм, до</td><td>10</td><td>0,39</td><td>0,60</td><td>0,77</td><td>0,99</td><td>1,19</td><td>1,42</td><td>1,63</td><td>1,83</td></tr>
<tr><td>9</td><td>20</td><td>0,55</td><td>0,85</td><td>1,09</td><td>1,40</td><td>1,67</td><td>1,99</td><td>2,92</td><td>2,57</td></tr>
<tr><td>10</td><td>30</td><td>0,68</td><td>1,05</td><td>1,35</td><td>1,73</td><td>2,07</td><td>2,47</td><td>2,84</td><td>3,18</td></tr>
<tr><td>11</td><td>40</td><td>0,85</td><td>1,30</td><td>1,67</td><td>2,15</td><td>2,57</td><td>3,08</td><td>3,53</td><td>3,96</td></tr>
<tr><td>12</td><td>50</td><td>1,05</td><td>1,60</td><td>2,06</td><td>2,65</td><td>3,17</td><td>3,79</td><td>4,35</td><td>4,87</td></tr>
<tr><td>13</td><td>60</td><td>1,24</td><td>1,90</td><td>2,45</td><td>3,15</td><td>3,76</td><td>4,50</td><td>5,16</td><td>5,78</td></tr>
<tr><td>14</td><td>70</td><td>1,43</td><td>2,19</td><td>2,82</td><td>3,63</td><td>4,33</td><td>5,18</td><td>5,95</td><td>6,66</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="9%"><col width="16%"><col width="9%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Правка углового, круглого и квадратного проката на ролико- и вальцеправильных машинах</td><td colspan="3">Правка</td></tr>
<tr><td colspan="3">Карта 9, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид проката</td><td colspan="2">Номер или размер</td><td colspan="8">Длина детали L, мм, до</td></tr>
<tr><td colspan="2" rowspan="2">проката</td><td>1000</td><td>2000</td><td>3000</td><td>4300</td><td>6000</td><td>8000</td><td>10000</td><td>12000</td></tr>
<tr><td colspan="8">Время на деталь Т, чел.-мин.</td></tr>
<tr><td>15</td><td rowspan="6">(рисунок не приводится)</td><td rowspan="6">альфа, мм, до</td><td>30</td><td>0,95</td><td>1,46</td><td>1,89</td><td>2,44</td><td>2,93</td><td>3,51</td><td>4,04</td><td>4,54</td></tr>
<tr><td>16</td><td>40</td><td>1,17</td><td>1,81</td><td>2,34</td><td>3,02</td><td>3,62</td><td>4,34</td><td>5,00</td><td>5,61</td></tr>
<tr><td>17</td><td>50</td><td>1,38</td><td>2,13</td><td>2,75</td><td>3,54</td><td>4,25</td><td>5,09</td><td>5,86</td><td>6,57</td></tr>
<tr><td>18</td><td>60</td><td>1,57</td><td>2,44</td><td>3,15</td><td>4,06</td><td>4,87</td><td>5,84</td><td>6,72</td><td>7,54</td></tr>
<tr><td>19</td><td>70</td><td>1,76</td><td>2,73</td><td>3,52</td><td>4,54</td><td>5,45</td><td>6,53</td><td>7,52</td><td>8,43</td></tr>
<tr><td>20</td><td>80</td><td>1,94</td><td>3,00</td><td>3,88</td><td>5,01</td><td>6,00</td><td>7,19</td><td>8,28</td><td>9,29</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p100464"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="11%"><col width="11%"><col width="11%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="15%"><col width="14%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td><td colspan="4">Количество одновременно обрабатываемых деталей</td><td colspan="2">Правка квадрата</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>1</td><td>2</td><td>3</td><td>св. 3</td><td>в двух плоскостях</td><td>в одной плоскости</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,8</td><td>0,6</td><td>0,4</td><td>1,0</td><td>0,7</td></tr>
</table>


2. <a id="p100467"></a>Работа выполняется бригадой из двух человек:

                             0,55    0,68
<a id="p100468"></a>              Т = 0,00166 х N     х L           поз. 1...7;

                             0,5    0,62
<a id="p100469"></a>              Т = 0,00171 х Д    х L            поз. 8...10;

                             0,93    0,62
<a id="p100470"></a>              Т = 0,00038 х Д     х L           поз. 11...14;

                                 0,73    0,68
<a id="p100471"></a>              Т = 0,00102 х альфа     х L       поз. 15...20.


<table>
<colgroup><col width="9%"><col width="11%"><col width="15%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="8%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Правка полос в пяти-, семивалковых вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 10, лист 1</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">1. Подать полосу к вальцам, установить между валками. (рисунок не</td></tr>
<tr><td colspan="13">2. Выправить полосу, проверить на точность линейкой. приводится)</td></tr>
<tr><td colspan="13">3. Снять выправленную полосу, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Толщина полосы</td><td rowspan="2">Количество устанавливаемых в вальцах</td><td colspan="10">Длина полосы L, мм, до</td></tr>
<tr><td rowspan="2">h, мм, до</td><td>700</td><td>1000</td><td>1400</td><td>2000</td><td>3000</td><td colspan="2">4200</td><td>6000</td><td>8600</td><td>12000</td></tr>
<tr><td>полос n, шт.</td><td colspan="10">Время на полосу Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="5">4</td><td>1</td><td>0,58</td><td>0,73</td><td>0,91</td><td>1,14</td><td>1,48</td><td colspan="2">1,84</td><td>2,31</td><td>2,90</td><td>3,59</td></tr>
<tr><td>2</td><td>2</td><td>0,48</td><td>0,60</td><td>0,74</td><td>0,93</td><td>1,21</td><td colspan="2">1,50</td><td>1,89</td><td>2,37</td><td>2,94</td></tr>
<tr><td>3</td><td>3</td><td>0,42</td><td>0,53</td><td>0,66</td><td>0,83</td><td>1,08</td><td colspan="2">1,33</td><td>1,68</td><td>2,11</td><td>2,61</td></tr>
<tr><td>4</td><td>4</td><td>0,39</td><td>0,49</td><td>0,61</td><td>0,76</td><td>0,99</td><td colspan="2">1,23</td><td>1,54</td><td>1,94</td><td>2,40</td></tr>
<tr><td>5</td><td>5</td><td>0,37</td><td>0,46</td><td>0,57</td><td>0,72</td><td>0,93</td><td colspan="2">1,15</td><td>1,45</td><td>1,82</td><td>2,25</td></tr>
<tr><td>6</td><td rowspan="5">8</td><td>1</td><td>0,76</td><td>0,95</td><td>1,18</td><td>1,48</td><td>1,93</td><td colspan="2">2,39</td><td>3,00</td><td>3,78</td><td>4,68</td></tr>
<tr><td>7</td><td>2</td><td>0,62</td><td>0,78</td><td>0,97</td><td>1,21</td><td>1,57</td><td colspan="2">1,95</td><td>2,45</td><td>3,09</td><td>3,82</td></tr>
<tr><td>8</td><td>3</td><td>0,55</td><td>0,69</td><td>0,86</td><td>1,08</td><td>1,40</td><td colspan="2">1,74</td><td>2,18</td><td>2,75</td><td>3,40</td></tr>
<tr><td>9</td><td>4</td><td>0,51</td><td>0,64</td><td>0,79</td><td>0,99</td><td>1,29</td><td colspan="2">1,60</td><td>2,01</td><td>2,53</td><td>3,13</td></tr>
<tr><td>10</td><td>5</td><td>0,48</td><td>0,60</td><td>0,74</td><td>0,93</td><td>1,21</td><td colspan="2">1,50</td><td>1,88</td><td>2,37</td><td>2,93</td></tr>
<tr><td>11</td><td rowspan="5">12</td><td>1</td><td>0,89</td><td>1,11</td><td>1,38</td><td>1,73</td><td>2,25</td><td colspan="2">2,79</td><td>3,50</td><td>4,41</td><td>5,45</td></tr>
<tr><td>12</td><td>2</td><td>0,72</td><td>0,91</td><td>1,13</td><td>1,42</td><td>1,84</td><td colspan="2">2,28</td><td>2,86</td><td>3,60</td><td>4,46</td></tr>
<tr><td>13</td><td>3</td><td>0,64</td><td>0,81</td><td>10,03</td><td>1,26</td><td>1,63</td><td colspan="2">2,03</td><td>2,55</td><td>3,20</td><td>3,97</td></tr>
<tr><td>14</td><td>4</td><td>0,59</td><td>0,74</td><td>0,92</td><td>1,16</td><td>1,50</td><td colspan="2">1,86</td><td>2,34</td><td>2,95</td><td>3,65</td></tr>
<tr><td>15</td><td>5</td><td>0,55</td><td>0,70</td><td>0,86</td><td>1,09</td><td>1,41</td><td colspan="2">1,75</td><td>2,19</td><td>2,76</td><td>3,42</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="9%"><col width="11%"><col width="15%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="8%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Правка полос в пяти-, семивалковых вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 10, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Толщина полосы</td><td rowspan="2">Кол-во устанавливаемых в вальцах</td><td colspan="10">Длина полосы L, мм, до</td></tr>
<tr><td rowspan="2">h, мм, до</td><td>700</td><td>1000</td><td>1400</td><td>2000</td><td>3000</td><td colspan="2">4200</td><td>6000</td><td>8600</td><td>12000</td></tr>
<tr><td>полос n, шт.</td><td colspan="10">Время на полосу Т, чел.-мин.</td></tr>
<tr><td>16</td><td rowspan="5">18</td><td>1</td><td>1,03</td><td>1,30</td><td>1,61</td><td>2,02</td><td>2,62</td><td colspan="2">3,25</td><td>4,08</td><td>5,14</td><td>6,36</td></tr>
<tr><td>17</td><td>2</td><td>0,84</td><td>1,06</td><td>1,32</td><td>1,65</td><td>2,14</td><td colspan="2">2,66</td><td>3,34</td><td>4,21</td><td>5,20</td></tr>
<tr><td>18</td><td>3</td><td>0,75</td><td>0,94</td><td>1,17</td><td>1,47</td><td>1,91</td><td colspan="2">2,36</td><td>2,96</td><td>3,74</td><td>4,63</td></tr>
<tr><td>19</td><td>4</td><td>0,69</td><td>0,87</td><td>1,08</td><td>1,35</td><td>1,75</td><td colspan="2">2,17</td><td>2,73</td><td>3,44</td><td>4,26</td></tr>
<tr><td>20</td><td>5</td><td>0,65</td><td>0,81</td><td>1,01</td><td>1,27</td><td>1,64</td><td colspan="2">2,04</td><td>2,56</td><td>3,22</td><td>3,99</td></tr>
<tr><td>21</td><td rowspan="5">24</td><td>1</td><td>1,15</td><td>1,45</td><td>1,79</td><td>2,25</td><td>2,92</td><td colspan="2">3,63</td><td>4,56</td><td>5,74</td><td>7,10</td></tr>
<tr><td>22</td><td>2</td><td>0,94</td><td>1,18</td><td>1,47</td><td>1,84</td><td>2,39</td><td colspan="2">2,96</td><td>3,73</td><td>4,69</td><td>5,81</td></tr>
<tr><td>23</td><td>3</td><td>0,84</td><td>1,05</td><td>1,31</td><td>1,64</td><td>2,13</td><td colspan="2">2,64</td><td>3,31</td><td>4,17</td><td>5,16</td></tr>
<tr><td>24</td><td>4</td><td>0,77</td><td>0,97</td><td>1,20</td><td>1,51</td><td>1,96</td><td colspan="2">2,43</td><td>3,05</td><td>3,84</td><td>4,75</td></tr>
<tr><td>25</td><td>5</td><td>0,72</td><td>0,91</td><td>1,13</td><td>1,41</td><td>1,83</td><td colspan="2">2,27</td><td>2,86</td><td>3,60</td><td>4,45</td></tr>
<tr><td>26</td><td rowspan="5">32</td><td>1</td><td>1,16</td><td>1,46</td><td>1,81</td><td>2,27</td><td>2,95</td><td colspan="2">3,65</td><td>4,59</td><td>5,78</td><td>7,15</td></tr>
<tr><td>27</td><td>2</td><td>0,95</td><td>1,19</td><td>1,48</td><td>1,86</td><td>2,41</td><td colspan="2">2,99</td><td>3,76</td><td>4,73</td><td>5,85</td></tr>
<tr><td>28</td><td>3</td><td>0,84</td><td>1,06</td><td>1,32</td><td>1,65</td><td>2,14</td><td colspan="2">2,66</td><td>3,34</td><td>4,20</td><td>5,20</td></tr>
<tr><td>29</td><td>4</td><td>0,78</td><td>0,98</td><td>1,21</td><td>1,52</td><td>1,97</td><td colspan="2">2,44</td><td>3,07</td><td>3,87</td><td>4,79</td></tr>
<tr><td>30</td><td>5</td><td>0,73</td><td>0,91</td><td>1,13</td><td>1,43</td><td>1,85</td><td colspan="2">2,29</td><td>2,88</td><td>3,62</td><td>4,49</td></tr>
<tr><td>31</td><td rowspan="5">40</td><td>1</td><td>1,40</td><td>1,76</td><td>2,18</td><td>2,74</td><td>3,55</td><td colspan="2">4,40</td><td>5,53</td><td>6,96</td><td>8,62</td></tr>
<tr><td>32</td><td>2</td><td>1,14</td><td>1,44</td><td>1,78</td><td>2,24</td><td>2,90</td><td colspan="2">3,60</td><td>4,52</td><td>5,70</td><td>7,05</td></tr>
<tr><td>33</td><td>3</td><td>1,02</td><td>1,28</td><td>1,58</td><td>1,99</td><td>2,58</td><td colspan="2">3,20</td><td>4,02</td><td>5,06</td><td>6,27</td></tr>
<tr><td>34</td><td>4</td><td>0,94</td><td>1,18</td><td>1,46</td><td>1,83</td><td>2,37</td><td colspan="2">2,95</td><td>3,70</td><td>4,66</td><td>5,77</td></tr>
<tr><td>35</td><td>5</td><td>0,88</td><td>1,10</td><td>1,37</td><td>1,72</td><td>2,23</td><td colspan="2">2,76</td><td>3,47</td><td>4,37</td><td>5,40</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="74%"><col width="26%"></colgroup>
<tr><td rowspan="2">Правка полос в пяти-, семивалковых вальцах</td><td>Правка</td></tr>
<tr><td>Карта 10, лист 3</td></tr>
</table>


<a id="p100521"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="15%"><col width="14%"><col width="11%"><col width="15%"><col width="14%"><col width="16%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="3">Материал</td><td colspan="3">Скорость вращения валков, м/мин.</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>до 6</td><td>7 - 8</td><td>св. 8</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,1</td><td>1,0</td><td>0,9</td></tr>
</table>


2. <a id="p100524"></a>Работа выполняется бригадой из двух человек:

                                      0,38    0,64
                            0,0052 х h     х L
<a id="p100525"></a>                        Т = ----------------------.
                                      0,29
                                     n


<table>
<colgroup><col width="11%"><col width="31%"><col width="8%"><col width="8%"><col width="8%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9">Правка мелких деталей в пяти-, семивалковых вальцах Правка</td></tr>
<tr><td colspan="9">Карта 11</td></tr>
<tr><td colspan="9">Содержание работы</td></tr>
<tr><td colspan="9">1. Уложить детали на вспомогательный лист.</td></tr>
<tr><td colspan="9">2. Править детали, проверить на точность линейкой.</td></tr>
<tr><td colspan="9">3. Снять детали, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Количество одновременно правимых</td><td colspan="7">Толщина деталей h, мм, до</td></tr>
<tr><td rowspan="2">деталей на листе n, шт., до</td><td>4</td><td>6</td><td>10</td><td>16</td><td>24</td><td>30</td><td>40</td></tr>
<tr><td colspan="7">Время на деталь Т, чел.-мин.</td></tr>
<tr><td>1</td><td>5</td><td>0,29</td><td>0,32</td><td>0,35</td><td>0,40</td><td>0,44</td><td>0,46</td><td>0,50</td></tr>
<tr><td>2</td><td>10</td><td>0,23</td><td>0,26</td><td>0,30</td><td>0,33</td><td>0,37</td><td>0,39</td><td>0,41</td></tr>
<tr><td>3</td><td>25</td><td>0,19</td><td>0,21</td><td>0,23</td><td>0,26</td><td>0,29</td><td>0,31</td><td>0,32</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td></tr>
</table>


<a id="p100537"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="15%"><col width="14%"><col width="11%"><col width="15%"><col width="14%"><col width="16%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="3">Материал</td><td colspan="3">Скорость вращения валков, м/мин.</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>до 6</td><td>7 - 8</td><td>св. 8</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,1</td><td>1,0</td><td>0,9</td></tr>
</table>


2. <a id="p100540"></a>Нормативы времени рассчитаны на правку деталей размером до 300 х 300 мм.
3. <a id="p100541"></a>Работа выполняется одним человеком:

                                          0,24
                                         h
<a id="p100542"></a>                             Т = 0,311 х -----.
                                          0,26
                                         n


<table>
<colgroup><col width="7%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="11" rowspan="2">Правка полос на фрикционном прессе</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 12, лист 1</td></tr>
<tr><td colspan="15">Содержание работы</td></tr>
<tr><td colspan="15">1. Подать полосу на плиту пресса.</td></tr>
<tr><td colspan="15">2. Править полосу, проверить на точность линейкой.</td></tr>
<tr><td colspan="15">3. Снять выправленную полосу, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина полосы</td><td>Длина полосы</td><td colspan="12">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">L, мм, до</td><td>4</td><td>8</td><td>12</td><td>18</td><td>24</td><td>32</td><td>40</td><td colspan="2">50</td><td>65</td><td>80</td><td>105</td></tr>
<tr><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="5">70</td><td>1000</td><td>0,36</td><td>0,51</td><td>0,62</td><td>0,76</td><td>0,88</td><td>1,00</td><td>1,15</td><td colspan="2">1,25</td><td>1,50</td><td>1,60</td><td>1,90</td></tr>
<tr><td>2</td><td>1400</td><td>0,42</td><td>0,59</td><td>0,74</td><td>0,92</td><td>1,05</td><td>1,25</td><td>1,36</td><td colspan="2">1,55</td><td>1,75</td><td>1,95</td><td>2,25</td></tr>
<tr><td>3</td><td>2000</td><td>0,51</td><td>0,72</td><td>0,88</td><td>1,10</td><td>1,25</td><td>1,45</td><td>1,65</td><td colspan="2">1,85</td><td>2,10</td><td>2,35</td><td>2,70</td></tr>
<tr><td>4</td><td>3000</td><td>0,62</td><td>0,88</td><td>1,10</td><td>1,30</td><td>1,55</td><td>1,80</td><td>2,00</td><td colspan="2">2,25</td><td>2,55</td><td>2,86</td><td>3,25</td></tr>
<tr><td>5</td><td>4200</td><td>0,73</td><td>1,00</td><td>1,25</td><td>1,60</td><td>1,80</td><td>2,10</td><td>2,35</td><td colspan="2">2,65</td><td>3,05</td><td>3,35</td><td>3,85</td></tr>
<tr><td>6</td><td rowspan="4">100</td><td>1000</td><td>0,45</td><td>0,63</td><td>0,76</td><td>0,97</td><td>1,10</td><td>1,25</td><td>1,45</td><td colspan="2">1,60</td><td>1,85</td><td>2,05</td><td>2,40</td></tr>
<tr><td>7</td><td>1400</td><td>0,53</td><td>0,74</td><td>0,92</td><td>1,15</td><td>1,30</td><td>1,55</td><td>1,70</td><td colspan="2">1,90</td><td>2,15</td><td>2,40</td><td>2,75</td></tr>
<tr><td>8</td><td>2000</td><td>0,63</td><td>0,88</td><td>1,10</td><td>1,35</td><td>1,60</td><td>1,80</td><td>2,00</td><td colspan="2">2,30</td><td>2,60</td><td>2,90</td><td>3,35</td></tr>
<tr><td>9</td><td>3000</td><td>0,77</td><td>1,10</td><td>1,35</td><td>1,65</td><td>1,95</td><td>2,25</td><td>2,50</td><td colspan="2">2,80</td><td>3,15</td><td>3,55</td><td>4,10</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="11" rowspan="2">Правка полос на фрикционном прессе</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 12, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина полосы</td><td>Длина полосы</td><td colspan="12">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">L, мм, до</td><td>4</td><td>8</td><td>12</td><td>18</td><td>24</td><td>32</td><td>40</td><td colspan="2">50</td><td>65</td><td>80</td><td>105</td></tr>
<tr><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>10</td><td>100</td><td>4200</td><td>0,91</td><td>1,30</td><td>1,60</td><td>1,95</td><td>2,30</td><td>2,65</td><td>2,95</td><td colspan="2">3,30</td><td>3,75</td><td>4,20</td><td>4,85</td></tr>
<tr><td>11</td><td rowspan="5">140</td><td>1000</td><td>0,55</td><td>0,78</td><td>0,96</td><td>1,20</td><td>1,35</td><td>1,60</td><td>1,75</td><td colspan="2">2,00</td><td>2,25</td><td>2,50</td><td>2,90</td></tr>
<tr><td>12</td><td>1400</td><td>0,65</td><td>0,92</td><td>1,15</td><td>1,40</td><td>1,60</td><td>1,90</td><td>2,10</td><td colspan="2">2,35</td><td>2,70</td><td>3,00</td><td>3,40</td></tr>
<tr><td>13</td><td>2000</td><td>0,78</td><td>1,1</td><td>1,35</td><td>1,65</td><td>1,95</td><td>2,25</td><td>2,50</td><td colspan="2">2,80</td><td>3,20</td><td>3,55</td><td>4,10</td></tr>
<tr><td>14</td><td>3000</td><td>0,95</td><td>1,35</td><td>1,65</td><td>2,05</td><td>2,35</td><td>2,70</td><td>3,10</td><td colspan="2">3,45</td><td>3,95</td><td>4,40</td><td>5,00</td></tr>
<tr><td>15</td><td>4200</td><td>1,13</td><td>1,55</td><td>2,00</td><td>2,40</td><td>2,80</td><td>3,25</td><td>3,65</td><td colspan="2">4,10</td><td>4,65</td><td>5,20</td><td>5,95</td></tr>
<tr><td>16</td><td rowspan="5">200</td><td>1000</td><td>0,68</td><td>0,97</td><td>1,20</td><td>1,45</td><td>1,70</td><td>2,00</td><td>2,20</td><td colspan="2">2,45</td><td>2,80</td><td>3,15</td><td>3,60</td></tr>
<tr><td>17</td><td>1400</td><td>0,81</td><td>1,15</td><td>1,40</td><td>1,72</td><td>2,00</td><td>2,35</td><td>2,60</td><td colspan="2">2,95</td><td>3,35</td><td>3,75</td><td>4,25</td></tr>
<tr><td>18</td><td>2000</td><td>0,97</td><td>1,36</td><td>1,70</td><td>2,05</td><td>2,40</td><td>2,80</td><td>3,10</td><td colspan="2">3,50</td><td>4,00</td><td>4,50</td><td>5,10</td></tr>
<tr><td>19</td><td>3000</td><td>1,19</td><td>1,65</td><td>2,05</td><td>2,55</td><td>2,90</td><td>3,40</td><td>3,80</td><td colspan="2">4,40</td><td>4,90</td><td>5,40</td><td>6,20</td></tr>
<tr><td>20</td><td>4200</td><td>1,40</td><td>2,00</td><td>2,45</td><td>3,00</td><td>3,45</td><td>4,05</td><td>4,55</td><td colspan="2">5,10</td><td>5,80</td><td>6,40</td><td>7,40</td></tr>
<tr><td>21</td><td rowspan="3">300</td><td>1000</td><td>0,88</td><td>1,25</td><td>1,54</td><td>1,09</td><td>2,20</td><td>2,55</td><td>2,85</td><td colspan="2">3,20</td><td>3,65</td><td>4,05</td><td>4,65</td></tr>
<tr><td>22</td><td>1400</td><td>1,04</td><td>1,50</td><td>1,80</td><td>2,25</td><td>2,60</td><td>3,00</td><td>3,40</td><td colspan="2">3,80</td><td>4,30</td><td>4,85</td><td>5,55</td></tr>
<tr><td>23</td><td>2000</td><td>1,25</td><td>1,75</td><td>2,20</td><td>2,70</td><td>3,10</td><td>3,60</td><td>4,05</td><td colspan="2">4,50</td><td>5,20</td><td>5,70</td><td>6,60</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="11" rowspan="2">Правка полос на фрикционном прессе</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 12, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина полосы</td><td>Длина полосы</td><td colspan="12">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">L, мм, до</td><td>4</td><td>8</td><td>12</td><td>18</td><td>24</td><td>32</td><td>40</td><td colspan="2">50</td><td>65</td><td>80</td><td>105</td></tr>
<tr><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>24</td><td rowspan="2">300</td><td>3000</td><td>1,53</td><td>2,16</td><td>2,70</td><td>3,30</td><td>3,80</td><td>4,40</td><td>4,90</td><td colspan="2">5,50</td><td>6,30</td><td>7,00</td><td>8,10</td></tr>
<tr><td>25</td><td>4200</td><td>1,80</td><td>2,55</td><td>3,16</td><td>3,85</td><td>4,50</td><td>5,20</td><td>5,80</td><td colspan="2">6,50</td><td>7,40</td><td>8,20</td><td>9,60</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td></tr>
</table>


<a id="p100584"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="9%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="6%"><col width="5%"><col width="6%"><col width="4%"><col width="6%"></colgroup>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="5">Правка полос</td><td colspan="6">Стрела прогиба, мм на 1 м</td></tr>
<tr><td rowspan="4">на изменение нормы времени</td><td rowspan="4">легированная сталь</td><td rowspan="4">углеродистая сталь</td><td rowspan="4">цветные сплавы</td><td rowspan="4">после газовой резки</td><td rowspan="4">на гидравлическом прессе с 3 - 4 ударами в мин.</td><td rowspan="4">на фрикционном прессе</td><td rowspan="4">с предварительным нагревом</td><td rowspan="4">в холодном состоянии</td><td colspan="6">до правки</td></tr>
<tr><td colspan="2">до 15</td><td colspan="2">16 - 30</td><td colspan="2">св. 30</td></tr>
<tr><td colspan="6">после правки</td></tr>
<tr><td>&lt; 2</td><td>2 - 4</td><td>&lt; 2</td><td>2 - 4</td><td>&lt; 2</td><td>2 - 4</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,2</td><td>1,25</td><td>1,0</td><td>1,1</td><td>1,0</td><td>1,0</td><td>0,85</td><td>1,25</td><td>1,0</td><td>1,5</td><td>1,15</td></tr>
</table>


2. <a id="p100587"></a>Работа выполняется бригадой из двух человек:

                                  0,62    0,5    0,51
<a id="p100588"></a>                    Т = 0,0004 х В     х L    х h    .


<table>
<colgroup><col width="11%"><col width="22%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="5%"><col width="4%"><col width="11%"><col width="9%"></colgroup>
<tr><td colspan="7" rowspan="2">Правка мелких деталей на фрикционном прессе</td><td colspan="3">Правка</td></tr>
<tr><td colspan="3">Карта 13, лист 1</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Подать деталь на плиту пресса.</td></tr>
<tr><td colspan="10">2. Править деталь, проверить на точность линейкой.</td></tr>
<tr><td colspan="10">3. Снять выправленную деталь, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Площадь детали S, кв.</td><td colspan="8">Толщина детали h, мм, до</td></tr>
<tr><td rowspan="2">м, до</td><td>4</td><td>8</td><td>12</td><td>18</td><td colspan="2">24</td><td>32</td><td>40</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>0,005</td><td>0,054</td><td>0,078</td><td>0,097</td><td>0,120</td><td colspan="2">0,140</td><td>0,163</td><td>0,184</td></tr>
<tr><td>2</td><td>0,010</td><td>0,080</td><td>0,120</td><td>0,140</td><td>0,180</td><td colspan="2">0,210</td><td>0,250</td><td>0,280</td></tr>
<tr><td>3</td><td>0,030</td><td>0,145</td><td>0,209</td><td>0,259</td><td>0,322</td><td colspan="2">0,375</td><td>0,437</td><td>0,491</td></tr>
<tr><td>4</td><td>0,050</td><td>0,192</td><td>0,277</td><td>0,343</td><td>0,426</td><td colspan="2">0,496</td><td>0,578</td><td>0,650</td></tr>
<tr><td>5</td><td>0,070</td><td>0,231</td><td>0,334</td><td>0,414</td><td>0,513</td><td colspan="2">0,598</td><td>0,696</td><td>0,784</td></tr>
<tr><td>5</td><td>0,100</td><td>0,282</td><td>0,406</td><td>0,503</td><td>0,624</td><td colspan="2">0,727</td><td>0,847</td><td>0,953</td></tr>
<tr><td>7</td><td>0,150</td><td>0,352</td><td>0,509</td><td>0,631</td><td>0,782</td><td colspan="2">0,910</td><td>1,060</td><td>1,194</td></tr>
<tr><td>8</td><td>0,200</td><td>0,412</td><td>0,595</td><td>0,737</td><td>0,914</td><td colspan="2">1,065</td><td>1,241</td><td>1,395</td></tr>
<tr><td>9</td><td>0,250</td><td>0,466</td><td>0,674</td><td>0,836</td><td>1,036</td><td colspan="2">1,207</td><td>1,405</td><td>1,582</td></tr>
<tr><td>10</td><td>0,300</td><td>0,516</td><td>0,743</td><td>0,922</td><td>1,143</td><td colspan="2">1,331</td><td>1,550</td><td>1,744</td></tr>
<tr><td>11</td><td>0,350</td><td>0,561</td><td>0,809</td><td>1,004</td><td>1,244</td><td colspan="2">1,449</td><td>1,688</td><td>1,900</td></tr>
<tr><td>12</td><td>0,400</td><td>0,604</td><td>0,872</td><td>1,082</td><td>1,341</td><td colspan="2">1,562</td><td>1,819</td><td>2,047</td></tr>
<tr><td>13</td><td>0,500</td><td>0,683</td><td>0,984</td><td>1,220</td><td>1,513</td><td colspan="2">1,762</td><td>2,052</td><td>2,309</td></tr>
<tr><td>14</td><td>0,600</td><td>0,755</td><td>1,089</td><td>1,350</td><td>1,675</td><td colspan="2">1,951</td><td>2,272</td><td>2,557</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td></tr>
</table>



<table>
<colgroup><col width="74%"><col width="26%"></colgroup>
<tr><td rowspan="2">Правка мелких деталей на фрикционном прессе</td><td>Правка</td></tr>
<tr><td>Карта 13, лист 2</td></tr>
</table>


<a id="p100613"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="12%"><col width="9%"><col width="9%"><col width="8%"><col width="12%"><col width="9%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="4">Правка деталей</td><td colspan="3">Одновременная правка деталей</td></tr>
<tr><td rowspan="2">на изменение нормы времени</td><td rowspan="2">легированная сталь</td><td rowspan="2">углеродистая сталь</td><td rowspan="2">цветные сплавы</td><td rowspan="2">на гидравлическом прессе с 3 - 4 уд. в мин.</td><td rowspan="2">на фрикционном прессе</td><td rowspan="2">с предварительным нагревом</td><td rowspan="2">в холодном состоянии</td><td colspan="3">типа шайб в количестве до</td></tr>
<tr><td>10</td><td>20</td><td>30</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,25</td><td>1,0</td><td>1,1</td><td>1,0</td><td>0,2</td><td>0,15</td><td>0,1</td></tr>
</table>


2. <a id="p100616"></a>Работа выполняется одним человеком:

                                       0,55    0,53
<a id="p100617"></a>                           Т = 0,57 х S     х h    .


<table>
<colgroup><col width="8%"><col width="12%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="12">Правка полос на плите после вальцовки вручную Правка</td></tr>
<tr><td colspan="12">Карта 14, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Подать полосу на плиту.</td></tr>
<tr><td colspan="12">2. Править полосу, проверить на точность линейкой.</td></tr>
<tr><td colspan="12">3. Снять выправленную полосу, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина полосы</td><td>Толщина полосы</td><td colspan="9">Длина полосы L, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">h, мм, до</td><td>200</td><td>400</td><td>700</td><td>1000</td><td>1500</td><td>2000</td><td>3000</td><td>4200</td><td>6000</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">70</td><td>10</td><td>0,18</td><td>0,31</td><td>0,48</td><td>0,63</td><td>0,88</td><td>1,11</td><td>1,53</td><td>2,00</td><td>2,66</td></tr>
<tr><td>2</td><td>20</td><td>0,20</td><td>0,35</td><td>0,54</td><td>0,72</td><td>1,01</td><td>1,25</td><td>1,75</td><td>2,25</td><td>3,05</td></tr>
<tr><td>3</td><td>30</td><td>0,22</td><td>0,38</td><td>0,60</td><td>0,79</td><td>1,10</td><td>1,38</td><td>1,91</td><td>2,50</td><td>3,33</td></tr>
<tr><td>4</td><td rowspan="3">140</td><td>10</td><td>0,20</td><td>0,35</td><td>0,55</td><td>0,73</td><td>1,01</td><td>1,27</td><td>1,76</td><td>2,30</td><td>3,06</td></tr>
<tr><td>5</td><td>20</td><td>0,23</td><td>0,40</td><td>0,63</td><td>0,83</td><td>1,16</td><td>1,45</td><td>2,0</td><td>2,6</td><td>3,5</td></tr>
<tr><td>6</td><td>30</td><td>0,25</td><td>0,44</td><td>0,68</td><td>0,91</td><td>1,26</td><td>1,58</td><td>2,19</td><td>2,87</td><td>3,82</td></tr>
<tr><td>7</td><td rowspan="3">200</td><td>10</td><td>0,22</td><td>0,37</td><td>0,59</td><td>0,78</td><td>1,08</td><td>1,36</td><td>1,89</td><td>2,47</td><td>3,28</td></tr>
<tr><td>8</td><td>20</td><td>0,25</td><td>0,43</td><td>0,67</td><td>0,89</td><td>1,24</td><td>1,55</td><td>2,15</td><td>2,80</td><td>3,75</td></tr>
<tr><td>9</td><td>30</td><td>0,27</td><td>0,47</td><td>0,73</td><td>0,98</td><td>1,35</td><td>1,70</td><td>2,35</td><td>3,08</td><td>4,10</td></tr>
<tr><td>10</td><td rowspan="3">300</td><td>10</td><td>0,23</td><td>0,41</td><td>0,64</td><td>0,85</td><td>1,18</td><td>1,48</td><td>2,05</td><td>2,68</td><td>3,57</td></tr>
<tr><td>11</td><td>20</td><td>0,27</td><td>0,47</td><td>0,73</td><td>0,98</td><td>1,35</td><td>1,70</td><td>2,35</td><td>3,07</td><td>4,09</td></tr>
<tr><td>12</td><td>30</td><td>0,29</td><td>0,51</td><td>0,79</td><td>1,06</td><td>1,47</td><td>1,84</td><td>2,55</td><td>3,34</td><td>4,44</td></tr>
<tr><td>13</td><td rowspan="3">400</td><td>10</td><td>0,25</td><td>0,43</td><td>0,68</td><td>0,90</td><td>1,25</td><td>1,57</td><td>2,17</td><td>2,84</td><td>3,78</td></tr>
<tr><td>14</td><td>20</td><td>0,28</td><td>0,49</td><td>0,78</td><td>1,03</td><td>1,43</td><td>1,80</td><td>2,49</td><td>3,26</td><td>4,34</td></tr>
<tr><td>15</td><td>30</td><td>0,31</td><td>0,54</td><td>0,84</td><td>1,12</td><td>1,55</td><td>1,95</td><td>2,70</td><td>3,54</td><td>4,41</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="73%"><col width="27%"></colgroup>
<tr><td rowspan="2">Правка полос на плите после вальцовки вручную</td><td>Правка</td></tr>
<tr><td>Карта 14, лист 2</td></tr>
</table>


<a id="p100643"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="15%"><col width="11%"><col width="11%"><col width="8%"><col width="11%"><col width="15%"><col width="14%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="4">Материал</td><td colspan="3">Правка полос</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>после вальцовки</td><td>после газовой резки</td><td>в холодном состоянии</td><td>с предварительным нагревом</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,1</td><td>0,8</td><td>1,0</td><td>1,2</td><td>1,0</td><td>1,1</td></tr>
</table>


2. <a id="p100646"></a>Работа выполняется одним человеком при L <= 1500 мм и бригадой из двух человек при L > 1500 мм:

                                       0,2    0,2    0,8
<a id="p100647"></a>                       Т = 0,000684 х В    х h    х L   .


<table>
<colgroup><col width="8%"><col width="12%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Правка полос на плите после резки на гильотинных ножницах вручную</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 15, лист 1</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">1. Подать полосу на плиту.</td></tr>
<tr><td colspan="13">2. Править полосу, проверить на точность линейкой.</td></tr>
<tr><td colspan="13">3. Снять выправленную полосу, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина полосы</td><td>Толщина полосы</td><td colspan="10">Длина полосы L, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">h, мм, до</td><td>200</td><td>400</td><td>700</td><td>1000</td><td>1500</td><td colspan="2">2000</td><td>3000</td><td>4200</td><td>6000</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="7">70</td><td>2</td><td>0,16</td><td>0,27</td><td>0,41</td><td>0,5</td><td>0,7</td><td colspan="2">0,9</td><td>1,2</td><td>1,5</td><td>2,0</td></tr>
<tr><td>2</td><td>4</td><td>0,25</td><td>0,42</td><td>0,64</td><td>0,8</td><td>1,1</td><td colspan="2">1,4</td><td>1,9</td><td>2,4</td><td>3,2</td></tr>
<tr><td>3</td><td>6</td><td>0,33</td><td>0,54</td><td>0,83</td><td>1,1</td><td>1,5</td><td colspan="2">1,8</td><td>2,5</td><td>3,2</td><td>4,2</td></tr>
<tr><td>4</td><td>8</td><td>0,39</td><td>0,66</td><td>1,01</td><td>1,3</td><td>1,8</td><td colspan="2">2,2</td><td>2,9</td><td>3,9</td><td>5,0</td></tr>
<tr><td>5</td><td>12</td><td>0,51</td><td>0,87</td><td>1,30</td><td>1,7</td><td>2,3</td><td colspan="2">2,9</td><td>3,9</td><td>5,1</td><td>6,6</td></tr>
<tr><td>6</td><td>16</td><td>0,62</td><td>1,05</td><td>1,60</td><td>2,1</td><td>2,8</td><td colspan="2">3,5</td><td>4,7</td><td>6,1</td><td>7,9</td></tr>
<tr><td>7</td><td>20</td><td>0,72</td><td>1,20</td><td>1,90</td><td>2,4</td><td>3,3</td><td colspan="2">4,1</td><td>5,5</td><td>7,1</td><td>9,3</td></tr>
<tr><td>8</td><td>100</td><td>2</td><td>0,18</td><td>0,30</td><td>0,46</td><td>0,6</td><td>0,8</td><td colspan="2">1,0</td><td>1,4</td><td>1,8</td><td>2,3</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="12%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Правка полос на плите после резки на гильотинных ножницах вручную</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 15, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина полосы</td><td>Толщина полосы</td><td colspan="10">Длина полосы L, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">h, мм, до</td><td>200</td><td>400</td><td>700</td><td>1000</td><td>1500</td><td colspan="2">2000</td><td>3000</td><td>4200</td><td>6000</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>9</td><td rowspan="6">100</td><td>4</td><td>0,29</td><td>0,48</td><td>0,73</td><td>0,9</td><td>1,3</td><td colspan="2">1,6</td><td>2,2</td><td>2,8</td><td>3,7</td></tr>
<tr><td>10</td><td>6</td><td>0,38</td><td>0,63</td><td>0,97</td><td>1,3</td><td>1,7</td><td colspan="2">2,1</td><td>2,9</td><td>3,7</td><td>4,8</td></tr>
<tr><td>11</td><td>8</td><td>0,46</td><td>0,77</td><td>1,20</td><td>1,5</td><td>2,1</td><td colspan="2">2,6</td><td>3,5</td><td>4,5</td><td>5,9</td></tr>
<tr><td>12</td><td>12</td><td>0,59</td><td>1,00</td><td>1,50</td><td>1,9</td><td>2,7</td><td colspan="2">3,4</td><td>4,5</td><td>5,8</td><td>7,6</td></tr>
<tr><td>13</td><td>16</td><td>0,72</td><td>1,20</td><td>1,80</td><td>2,4</td><td>3,3</td><td colspan="2">4,1</td><td>5,5</td><td>7,1</td><td>9,3</td></tr>
<tr><td>14</td><td>20</td><td>0,84</td><td>1,40</td><td>2,10</td><td>2,8</td><td>3,8</td><td colspan="2">4,7</td><td>6,4</td><td>8,2</td><td>10,7</td></tr>
<tr><td>15</td><td rowspan="7">140</td><td>2</td><td>0,21</td><td>0,35</td><td>0,53</td><td>0,6</td><td>0,9</td><td colspan="2">1,2</td><td>1,6</td><td>2,0</td><td>2,7</td></tr>
<tr><td>16</td><td>4</td><td>0,33</td><td>0,55</td><td>0,84</td><td>1,1</td><td>1,5</td><td colspan="2">1,8</td><td>2,5</td><td>3,2</td><td>4,2</td></tr>
<tr><td>17</td><td>6</td><td>0,43</td><td>0,73</td><td>1,10</td><td>1,5</td><td>1,9</td><td colspan="2">2,4</td><td>3,3</td><td>4,3</td><td>5,6</td></tr>
<tr><td>18</td><td>8</td><td>0,53</td><td>0,88</td><td>1,30</td><td>1,8</td><td>2,4</td><td colspan="2">2,9</td><td>4,0</td><td>5,2</td><td>6,7</td></tr>
<tr><td>19</td><td>12</td><td>0,69</td><td>1,1</td><td>1,7</td><td>2,3</td><td>3,1</td><td colspan="2">3,8</td><td>5,2</td><td>6,7</td><td>8,8</td></tr>
<tr><td>20</td><td>16</td><td>0,83</td><td>1,4</td><td>2,1</td><td>2,8</td><td>3,8</td><td colspan="2">4,7</td><td>6,3</td><td>8,1</td><td>10,6</td></tr>
<tr><td>21</td><td>20</td><td>0,96</td><td>1,6</td><td>2,5</td><td>3,2</td><td>4,4</td><td colspan="2">5,4</td><td>7,3</td><td>9,4</td><td>12,3</td></tr>
<tr><td>22</td><td>200</td><td>2</td><td>0,24</td><td>0,4</td><td>0,6</td><td>0,8</td><td>1,1</td><td colspan="2">1,4</td><td>1,9</td><td>2,4</td><td>3,1</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="12%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Правка полос на плите после резки на гильотинных ножницах вручную</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 15, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина полосы</td><td>Толщина полосы</td><td colspan="10">Длина полосы L, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">h, мм, до</td><td>200</td><td>400</td><td>700</td><td>1000</td><td>1500</td><td colspan="2">2000</td><td>3000</td><td>4200</td><td>6000</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>23</td><td rowspan="6">200</td><td>4</td><td>0,38</td><td>0,6</td><td>0,9</td><td>1,3</td><td>1,7</td><td colspan="2">2,1</td><td>2,9</td><td>3,7</td><td>4,9</td></tr>
<tr><td>24</td><td>6</td><td>0,50</td><td>0,8</td><td>1,3</td><td>1,7</td><td>2,3</td><td colspan="2">2,8</td><td>3,8</td><td>4,9</td><td>6,4</td></tr>
<tr><td>25</td><td>8</td><td>0,61</td><td>1,0</td><td>1,5</td><td>2,0</td><td>2,7</td><td colspan="2">3,4</td><td>4,6</td><td>5,9</td><td>7,8</td></tr>
<tr><td>26</td><td>12</td><td>0,79</td><td>1,3</td><td>2,0</td><td>2,6</td><td>3,6</td><td colspan="2">4,5</td><td>6,0</td><td>7,8</td><td>10,2</td></tr>
<tr><td>27</td><td>16</td><td>0,96</td><td>1,6</td><td>2,4</td><td>3,2</td><td>5,4</td><td colspan="2">7,3</td><td>9,4</td><td>10,4</td><td>12,3</td></tr>
<tr><td>28</td><td>20</td><td>1,11</td><td>1,9</td><td>2,8</td><td>3,7</td><td>5,0</td><td colspan="2">6,2</td><td>8,5</td><td>10,9</td><td>14,2</td></tr>
<tr><td>29</td><td rowspan="7">300</td><td>2</td><td>0,29</td><td>0,4</td><td>0,7</td><td>0,9</td><td>1,3</td><td colspan="2">1,6</td><td>2,2</td><td>2,8</td><td>3,7</td></tr>
<tr><td>30</td><td>4</td><td>0,45</td><td>0,7</td><td>1,2</td><td>1,5</td><td>2,1</td><td colspan="2">2,5</td><td>3,4</td><td>4,4</td><td>5,8</td></tr>
<tr><td>31</td><td>6</td><td>0,59</td><td>1,0</td><td>1,5</td><td>1,9</td><td>2,7</td><td colspan="2">3,3</td><td>4,5</td><td>5,8</td><td>7,6</td></tr>
<tr><td>32</td><td>8</td><td>0,72</td><td>1,2</td><td>1,8</td><td>2,4</td><td>3,2</td><td colspan="2">4,0</td><td>5,0</td><td>7,0</td><td>9,2</td></tr>
<tr><td>33</td><td>12</td><td>0,94</td><td>1,6</td><td>2,4</td><td>3,1</td><td>4,2</td><td colspan="2">5,3</td><td>7,1</td><td>9,2</td><td>11,9</td></tr>
<tr><td>34</td><td>16</td><td>1,10</td><td>1,9</td><td>2,9</td><td>3,8</td><td>5,1</td><td colspan="2">6,4</td><td>8,6</td><td>11,1</td><td>14,5</td></tr>
<tr><td>35</td><td>20</td><td>1,30</td><td>2,2</td><td>3,4</td><td>4,4</td><td>5,9</td><td colspan="2">7,4</td><td>10,0</td><td>12,9</td><td>16,8</td></tr>
<tr><td>36</td><td>400</td><td>2</td><td>0,32</td><td>0,5</td><td>0,8</td><td>1,1</td><td>1,5</td><td colspan="2">1,8</td><td>2,5</td><td>3,2</td><td>4,2</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="12%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Правка полос на плите после резки на гильотинных ножницах вручную</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 15, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина полосы</td><td>Толщина полосы</td><td colspan="10">Длина полосы L, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">h, мм, до</td><td>200</td><td>400</td><td>700</td><td>1000</td><td>1500</td><td colspan="2">2000</td><td>3000</td><td>4200</td><td>6000</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>37</td><td rowspan="6">400</td><td>4</td><td>0,51</td><td>0,8</td><td>1,3</td><td>1,7</td><td>2,3</td><td colspan="2">2,8</td><td>3,8</td><td>5,0</td><td>6,5</td></tr>
<tr><td>38</td><td>6</td><td>0,67</td><td>1,1</td><td>1,7</td><td>2,2</td><td>3,0</td><td colspan="2">3,7</td><td>5,1</td><td>6,5</td><td>8,5</td></tr>
<tr><td>39</td><td>8</td><td>0,81</td><td>1,4</td><td>2,1</td><td>2,7</td><td>3,7</td><td colspan="2">4,5</td><td>6,2</td><td>7,9</td><td>10,4</td></tr>
<tr><td>40</td><td>12</td><td>1,10</td><td>1,8</td><td>2,7</td><td>3,5</td><td>4,8</td><td colspan="2">5,9</td><td>8,0</td><td>10,3</td><td>13,5</td></tr>
<tr><td>41</td><td>16</td><td>1,30</td><td>2,1</td><td>3,3</td><td>4,3</td><td>5,8</td><td colspan="2">7,6</td><td>9,7</td><td>12,5</td><td>16,4</td></tr>
<tr><td>42</td><td>20</td><td>1,48</td><td>2,5</td><td>3,8</td><td>4,9</td><td>6,7</td><td colspan="2">8,3</td><td>11,3</td><td>14,5</td><td>18,9</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p100710"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="10%"><col width="8%"><col width="8%"><col width="7%"><col width="8%"><col width="9%"><col width="8%"><col width="8%"><col width="4%"><col width="7%"><col width="6%"><col width="7%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="14">Правка полос на плите после резки на гильотинных ножницах Правка вручную</td></tr>
<tr><td colspan="14">Карта 15, лист 5</td></tr>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="4">Правка полос</td><td colspan="6">Стрела прогиба, мм на 1 м</td></tr>
<tr><td rowspan="4">на изменение нормы времени</td><td rowspan="4">легированная сталь</td><td rowspan="4">углеродиcтая сталь</td><td rowspan="4">цветные сплавы</td><td rowspan="4">после резки на гильотинных ножницах</td><td rowspan="4">после газовой резки</td><td rowspan="4">с предварительным нагревом</td><td rowspan="4">в холодном состоянии</td><td colspan="6">до правки</td></tr>
<tr><td colspan="2">до 15</td><td colspan="2">16 - 30</td><td colspan="2">св. 30</td></tr>
<tr><td colspan="6">после правки</td></tr>
<tr><td>&lt; 2</td><td>2 - 4</td><td>&lt; 2</td><td>2 - 4</td><td>&lt; 2</td><td>2 - 4</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,2</td><td>1,1</td><td>1,0</td><td>1,0</td><td>0,85</td><td>1,25</td><td>1,0</td><td>1,5</td><td>1,15</td></tr>
</table>


2. <a id="p100715"></a>Работа выполняется одним человеком при L <= 1500 мм и бригадой из двух человек при L > 1500 мм:

                                    0,41    0,66    0,75
<a id="p100716"></a>                     Т = 0,00033 х В     х h     х L    .


<table>
<colgroup><col width="11%"><col width="22%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="7%"><col width="3%"><col width="11%"><col width="9%"></colgroup>
<tr><td colspan="7" rowspan="2">Правка мелких деталей на плите вручную</td><td colspan="3">Правка</td></tr>
<tr><td colspan="3">Карта 16, лист 1</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Подать деталь на плиту.</td></tr>
<tr><td colspan="10">2. Править деталь, проверить на точность линейкой.</td></tr>
<tr><td colspan="10">3. Снять выправленную деталь, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Площадь детали S,</td><td colspan="8">Толщина детали h, мм, до</td></tr>
<tr><td rowspan="2">кв. м, до</td><td>2</td><td>4</td><td>6</td><td>8</td><td colspan="2">12</td><td>16</td><td>20</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>0,005</td><td>0,13</td><td>0,17</td><td>0,20</td><td>0,23</td><td colspan="2">0,27</td><td>0,31</td><td>0,33</td></tr>
<tr><td>2</td><td>0,010</td><td>0,17</td><td>0,23</td><td>0,27</td><td>0,30</td><td colspan="2">0,36</td><td>0,41</td><td>0,45</td></tr>
<tr><td>3</td><td>0,030</td><td>0,27</td><td>0,36</td><td>0,42</td><td>0,48</td><td colspan="2">0,56</td><td>0,64</td><td>0,70</td></tr>
<tr><td>4</td><td>0,050</td><td>0,33</td><td>0,44</td><td>0,52</td><td>0,59</td><td colspan="2">0,69</td><td>0,79</td><td>0,86</td></tr>
<tr><td>5</td><td>0,070</td><td>0,38</td><td>0,50</td><td>0,60</td><td>0,67</td><td colspan="2">0,80</td><td>0,90</td><td>0,99</td></tr>
<tr><td>6</td><td>0,100</td><td>0,44</td><td>0,58</td><td>0,69</td><td>0,78</td><td colspan="2">0,93</td><td>1,04</td><td>1,15</td></tr>
<tr><td>7</td><td>0,150</td><td>0,51</td><td>0,69</td><td>0,82</td><td>0,92</td><td colspan="2">1,09</td><td>1,23</td><td>1,36</td></tr>
<tr><td>8</td><td>0,200</td><td>0,58</td><td>0,78</td><td>0,92</td><td>1,04</td><td colspan="2">1,23</td><td>1,39</td><td>1,53</td></tr>
<tr><td>9</td><td>0,250</td><td>0,63</td><td>0,85</td><td>1,01</td><td>1,14</td><td colspan="2">1,35</td><td>1,52</td><td>1,67</td></tr>
<tr><td>10</td><td>0,300</td><td>0,68</td><td>0,92</td><td>1,09</td><td>1,23</td><td colspan="2">1.45</td><td>1,64</td><td>1,80</td></tr>
<tr><td>11</td><td>0,350</td><td>0,73</td><td>0,98</td><td>1,16</td><td>1,31</td><td colspan="2">1,55</td><td>1,75</td><td>1,92</td></tr>
<tr><td>12</td><td>0,400</td><td>0,77</td><td>1,03</td><td>1,22</td><td>1,38</td><td colspan="2">1,63</td><td>1,85</td><td>2,03</td></tr>
<tr><td>13</td><td>0,500</td><td>0,84</td><td>1,13</td><td>1,34</td><td>1,51</td><td colspan="2">1,79</td><td>2,02</td><td>2,22</td></tr>
<tr><td>14</td><td>0,600</td><td>0,91</td><td>1,22</td><td>1,44</td><td>1,63</td><td colspan="2">1,93</td><td>2,18</td><td>2,39</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td></tr>
</table>



<table>
<colgroup><col width="73%"><col width="27%"></colgroup>
<tr><td rowspan="2">Правка мелких деталей на плите вручную</td><td>Правка</td></tr>
<tr><td>Карта 16, лист 2</td></tr>
</table>


<a id="p100741"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="15%"><col width="11%"><col width="11%"><col width="14%"><col width="15%"><col width="11%"><col width="8%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="3">Материал</td><td colspan="4">Правка деталей</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>с предварительным нагревом</td><td>в холодном состоянии</td><td>после зиговки</td><td>после гибки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,1</td><td>1,0</td><td>1,1</td><td>0,8</td></tr>
</table>


2. <a id="p100744"></a>Работа выполняется одним человеком:

                                    0,41    0,42
<a id="p100745"></a>                       Т = 0,839 х S     х h    .


<table>
<colgroup><col width="14%"><col width="22%"><col width="20%"><col width="22%"><col width="23%"></colgroup>
<tr><td colspan="5">Правка труб на правильной плите с подогревом газовой Правка горелкой вручную</td></tr>
<tr><td colspan="5">Карта 17, лист 1</td></tr>
<tr><td colspan="5">Содержание работы</td></tr>
<tr><td colspan="5">1. Установить трубу на плиту.</td></tr>
<tr><td colspan="5">2. Осмотреть гибы для правки, наметить место нагрева.</td></tr>
<tr><td colspan="5">3. Нагреть трубу, править, проверить на точность линейкой.</td></tr>
<tr><td colspan="5">4. Снять трубу, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2">Размеры трубы</td><td colspan="2">Вид трубы</td></tr>
<tr><td rowspan="2">Диаметр трубы Д, мм, до</td><td rowspan="2">Толщина стенок h, мм, до</td><td>Нешипованные</td><td>Шипованные</td></tr>
<tr><td colspan="2">Время на один гиб Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="6">32</td><td>3,0</td><td>0,43</td><td>0,57</td></tr>
<tr><td>2</td><td>3,5</td><td>0,48</td><td>0,64</td></tr>
<tr><td>3</td><td>4,0</td><td>0,52</td><td>0,69</td></tr>
<tr><td>4</td><td>4,5</td><td>0,58</td><td>0,77</td></tr>
<tr><td>5</td><td>5,0</td><td>0,62</td><td>0,82</td></tr>
<tr><td>6</td><td>6,0</td><td>0,71</td><td>0,94</td></tr>
<tr><td>7</td><td rowspan="6">38</td><td>3,0</td><td>0,53</td><td>0,70</td></tr>
<tr><td>8</td><td>3,5</td><td>0,59</td><td>0,78</td></tr>
<tr><td>9</td><td>4,0</td><td>0,64</td><td>0,85</td></tr>
<tr><td>10</td><td>4,5</td><td>0,71</td><td>0,94</td></tr>
<tr><td>11</td><td>5,0</td><td>0,77</td><td>1,02</td></tr>
<tr><td>12</td><td>6,0</td><td>0,87</td><td>1,15</td></tr>
<tr><td>13</td><td rowspan="4">42</td><td>3,0</td><td>0,60</td><td>0,80</td></tr>
<tr><td>14</td><td>3,5</td><td>0,67</td><td>0,89</td></tr>
<tr><td>15</td><td>4,0</td><td>0,72</td><td>0,95</td></tr>
<tr><td>16</td><td>4,5</td><td>0,80</td><td>1,05</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td></tr>
</table>



<table>
<colgroup><col width="14%"><col width="22%"><col width="20%"><col width="22%"><col width="23%"></colgroup>
<tr><td colspan="5">Правка труб на правильной плите с подогревом газовой Правка горелкой вручную</td></tr>
<tr><td colspan="5">Карта 17, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2">Размеры трубы</td><td colspan="2">Вид трубы</td></tr>
<tr><td rowspan="2">Диаметр трубы Д, мм, до</td><td rowspan="2">Толщина стенок h, мм, до</td><td>Нешипованные</td><td>Шипованные</td></tr>
<tr><td colspan="2">Время на один гиб Т, чел.-мин.</td></tr>
<tr><td>17</td><td rowspan="2">42</td><td>5,0</td><td>0,86</td><td>1,14</td></tr>
<tr><td>18</td><td>6,0</td><td>0,98</td><td>1,30</td></tr>
<tr><td>19</td><td rowspan="6">50</td><td>3,0</td><td>0,74</td><td>0,98</td></tr>
<tr><td>20</td><td>3,5</td><td>0,83</td><td>1,10</td></tr>
<tr><td>21</td><td>4,0</td><td>0,89</td><td>1,18</td></tr>
<tr><td>22</td><td>4,5</td><td>0,99</td><td>1,32</td></tr>
<tr><td>23</td><td>5,0</td><td>1,07</td><td>1,42</td></tr>
<tr><td>24</td><td>6,0</td><td>1,22</td><td>1,62</td></tr>
<tr><td>25</td><td rowspan="6">60</td><td>3,0</td><td>0,93</td><td>1,24</td></tr>
<tr><td>26</td><td>3,5</td><td>1,03</td><td>1,37</td></tr>
<tr><td>27</td><td>4,0</td><td>1,11</td><td>1,47</td></tr>
<tr><td>28</td><td>4,5</td><td>1,24</td><td>1,65</td></tr>
<tr><td>29</td><td>5,0</td><td>1,33</td><td>1,77</td></tr>
<tr><td>30</td><td>6,0</td><td>1,56</td><td>2,07</td></tr>
<tr><td>31</td><td rowspan="4">76</td><td>4,0</td><td>1,48</td><td>1,97</td></tr>
<tr><td>32</td><td>4,5</td><td>1,65</td><td>2,19</td></tr>
<tr><td>33</td><td>5,0</td><td>1,77</td><td>2,35</td></tr>
<tr><td>34</td><td>6,0</td><td>2,02</td><td>2,68</td></tr>
<tr><td>35</td><td rowspan="4">83</td><td>4,0</td><td>1,65</td><td>2,20</td></tr>
<tr><td>36</td><td>4,5</td><td>1,83</td><td>2,43</td></tr>
<tr><td>37</td><td>5,0</td><td>1,97</td><td>2,62</td></tr>
<tr><td>38</td><td>6,0</td><td>2,25</td><td>3,00</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td></tr>
</table>



<table>
<colgroup><col width="73%"><col width="27%"></colgroup>
<tr><td rowspan="2">Правка труб на правильной плите с подогревом газовой горелкой вручную</td><td>Правка</td></tr>
<tr><td>Карта 17, лист 3</td></tr>
</table>


<a id="p100799"></a>Примечания: 1. При измененных условиях правки шипованных труб приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="28%"><col width="18%"><col width="18%"><col width="18%"><col width="19%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="4">Длина труб с шипованным участком, м, до</td></tr>
<tr><td>времени</td><td>3 - 4</td><td>6</td><td>9</td><td>св. 9</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,5</td><td>1,7</td><td>2,0</td></tr>
</table>


2. <a id="p100802"></a>Работа выполняется одним человеком:

                      1,21    0,71
<a id="p100803"></a>         Т = 0,003 х Д     х h          индекс а, поз. 1...40;

                      1,21    0,71
<a id="p100804"></a>         Т = 0,004 х Д     х h          индекс б, поз. 1...40.


<table>
<colgroup><col width="7%"><col width="11%"><col width="11%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="10" rowspan="2">Правка угловой стали на плите вручную</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 18, лист 1</td></tr>
<tr><td colspan="14">Содержание работы</td></tr>
<tr><td colspan="14">1. Подать уголок на плиту.</td></tr>
<tr><td colspan="14">2. Править уголок, проверить на точность линейкой.</td></tr>
<tr><td colspan="14">3. Снять выправленный уголок, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>N профиля</td><td>Толщина угловой</td><td colspan="11">Длина уголка L, мм, до</td></tr>
<tr><td rowspan="2">N, до</td><td>стали h, мм,</td><td>500</td><td>700</td><td>1000</td><td>1500</td><td>2000</td><td>3000</td><td colspan="2">4200</td><td>6000</td><td>8600</td><td>12000</td></tr>
<tr><td>до</td><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>3,2</td><td>4</td><td>0,44</td><td>0,54</td><td>0,68</td><td>0,88</td><td>1,05</td><td>1,35</td><td colspan="2">1,66</td><td>1,98</td><td>2,53</td><td>3,19</td></tr>
<tr><td>2</td><td>5</td><td>5</td><td>0,45</td><td>0,56</td><td>0,70</td><td>0,90</td><td>1,09</td><td>1,40</td><td colspan="2">1,72</td><td>2,09</td><td>2,64</td><td>3,30</td></tr>
<tr><td>3</td><td>7,5</td><td>9</td><td>0,50</td><td>0,63</td><td>0,78</td><td>1,00</td><td>1,20</td><td>1,54</td><td colspan="2">1,89</td><td>2,42</td><td>2,97</td><td>3,63</td></tr>
<tr><td>4</td><td rowspan="3">10</td><td>8</td><td>0,57</td><td>0,70</td><td>0,87</td><td>1,12</td><td>1,34</td><td>1,73</td><td colspan="2">2,13</td><td>2,64</td><td>3,30</td><td>4,07</td></tr>
<tr><td>5</td><td>12</td><td>0,67</td><td>0,83</td><td>1,03</td><td>1,33</td><td>1,58</td><td>2,05</td><td colspan="2">2,53</td><td>3,19</td><td>3,96</td><td>4,84</td></tr>
<tr><td>6</td><td>16</td><td>0,77</td><td>0,96</td><td>1,19</td><td>1,53</td><td>1,84</td><td>2,31</td><td colspan="2">2,86</td><td>3,63</td><td>4,51</td><td>5,61</td></tr>
<tr><td>7</td><td rowspan="3">12,5</td><td>8</td><td>0,62</td><td>0,76</td><td>0,96</td><td>1,23</td><td>1,46</td><td>1,89</td><td colspan="2">2,31</td><td>2,86</td><td>3,63</td><td>4,40</td></tr>
<tr><td>8</td><td>12</td><td>0,76</td><td>0,95</td><td>1,18</td><td>1,51</td><td>1,82</td><td>2,31</td><td colspan="2">2,86</td><td>3,52</td><td>4,51</td><td>5,50</td></tr>
<tr><td>9</td><td>16</td><td>0,86</td><td>1,08</td><td>1,34</td><td>1,73</td><td>2,07</td><td>2,64</td><td colspan="2">3,19</td><td>4,07</td><td>5,06</td><td>6,27</td></tr>
<tr><td>10</td><td rowspan="3">16</td><td>8</td><td>0,73</td><td>1,02</td><td>1,11</td><td>1,43</td><td>1,71</td><td>2,20</td><td colspan="2">2,75</td><td>3,41</td><td>4,18</td><td>5,17</td></tr>
<tr><td>11</td><td>12</td><td>0,83</td><td>1,02</td><td>1,27</td><td>1,64</td><td>1,96</td><td>2,53</td><td colspan="2">3,19</td><td>3,85</td><td>4,84</td><td>5,94</td></tr>
<tr><td>12</td><td>16</td><td>0,99</td><td>1,22</td><td>1,52</td><td>1,96</td><td>2,31</td><td>2,97</td><td colspan="2">3,74</td><td>4,62</td><td>5,72</td><td>7,15</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="76%"><col width="24%"></colgroup>
<tr><td rowspan="2">Правка угловой стали на плите вручную</td><td>Правка</td></tr>
<tr><td>Карта 18, лист 2</td></tr>
</table>


<a id="p100827"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="11%"><col width="9%"><col width="8%"><col width="8%"><col width="6%"><col width="9%"><col width="10%"><col width="5%"><col width="8%"><col width="6%"><col width="8%"><col width="5%"><col width="8%"></colgroup>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="3">Правка</td><td colspan="6">Стрела прогиба, мм на 1 м</td></tr>
<tr><td rowspan="4">на изменение нормы времени</td><td rowspan="4">легированная сталь</td><td rowspan="4">углеродиcтая сталь</td><td rowspan="4">цветные сплавы</td><td rowspan="4">в холодном состоянии</td><td rowspan="4">с предварительным нагревом</td><td rowspan="4">после газовой резки</td><td colspan="6">до правки</td></tr>
<tr><td colspan="2">до 15</td><td colspan="2">16 - 30</td><td colspan="2">св. 30</td></tr>
<tr><td colspan="6">после правки</td></tr>
<tr><td>&lt; 2</td><td>2 - 4</td><td>&lt; 2</td><td>2 - 4</td><td>&lt; 2</td><td>2 - 4</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,0</td><td>0,85</td><td>1,25</td><td>1,0</td><td>1,5</td><td>1,15</td></tr>
</table>


2. <a id="p100830"></a>Работа выполняется одним человеком при L <= 1500 мм и бригадой из двух человек при L > 1500 мм:

                                     0,16    0,62
<a id="p100831"></a>                      Т = 0,00759 х h     х L          поз. 1...3;

                                 0,51    0,45    0,62
<a id="p100832"></a>                  Т = 0,00147 х N     х h     х L      поз. 4...12.


<table>
<colgroup><col width="11%"><col width="16%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Правка швеллерной стали на плите вручную</td><td colspan="3">Правка</td></tr>
<tr><td colspan="3">Карта 19, лист 1</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">1. Подать швеллер на плиту.</td></tr>
<tr><td colspan="11">2. Править вручную, проверить на точность линейкой.</td></tr>
<tr><td colspan="11">3. Снять выправленный швеллер, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">N профиля N, до</td><td colspan="9">Длина швеллера L, мм, до</td></tr>
<tr><td>700</td><td>1000</td><td>1500</td><td>2000</td><td>3000</td><td>4200</td><td>6000</td><td>8600</td><td>12000</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>5</td><td>0,65</td><td>0,77</td><td>0,95</td><td>1,14</td><td>1,5</td><td>1,9</td><td>2,5</td><td>3,2</td><td>4,0</td></tr>
<tr><td>2</td><td>6,5</td><td>0,76</td><td>0,91</td><td>1,12</td><td>1,37</td><td>1,8</td><td>2,3</td><td>2,9</td><td>3,8</td><td>4,8</td></tr>
<tr><td>3</td><td>8</td><td>0,89</td><td>1,07</td><td>1,31</td><td>1,59</td><td>2,1</td><td>2,7</td><td>3,4</td><td>4,4</td><td>5,6</td></tr>
<tr><td>4</td><td>10</td><td>1,05</td><td>1,25</td><td>1,54</td><td>1,84</td><td>2,4</td><td>3,1</td><td>3,9</td><td>5,1</td><td>6,4</td></tr>
<tr><td>5</td><td>12</td><td>1,19</td><td>1,42</td><td>1,74</td><td>2,10</td><td>2,8</td><td>3,5</td><td>4,5</td><td>5,8</td><td>7,4</td></tr>
<tr><td>6</td><td>14</td><td>1,32</td><td>1,58</td><td>1,93</td><td>2,30</td><td>3,1</td><td>3,9</td><td>5,1</td><td>6,5</td><td>8,2</td></tr>
<tr><td>7</td><td>16</td><td>1,45</td><td>1,73</td><td>2,10</td><td>2,60</td><td>3,4</td><td>4,3</td><td>5,6</td><td>7,1</td><td>9,0</td></tr>
<tr><td>8</td><td>18</td><td>1,59</td><td>1,90</td><td>2,30</td><td>2,80</td><td>3,7</td><td>4,7</td><td>6,0</td><td>7,8</td><td>9,8</td></tr>
<tr><td>9</td><td>20</td><td>1,71</td><td>2,00</td><td>2,50</td><td>3,00</td><td>4,0</td><td>5,0</td><td>6,5</td><td>8,4</td><td>10,6</td></tr>
<tr><td>10</td><td>22</td><td>1,82</td><td>2,20</td><td>2,70</td><td>3,20</td><td>4,3</td><td>5,4</td><td>6,9</td><td>8,9</td><td>11,3</td></tr>
<tr><td>11</td><td>24</td><td>1,95</td><td>2,30</td><td>2,80</td><td>3,40</td><td>4,5</td><td>5,8</td><td>7,4</td><td>9,5</td><td>12,0</td></tr>
<tr><td>12</td><td>30</td><td>2,30</td><td>2,70</td><td>3,30</td><td>4,00</td><td>5,3</td><td>6,7</td><td>8,6</td><td>11,1</td><td>14,0</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="74%"><col width="26%"></colgroup>
<tr><td rowspan="2">Правка швеллерной стали на плите вручную</td><td>Правка</td></tr>
<tr><td>Карта 19, лист 2</td></tr>
</table>


<a id="p100855"></a>Примечания: 1. При измененных условиях правки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="11%"><col width="9%"><col width="8%"><col width="8%"><col width="6%"><col width="9%"><col width="10%"><col width="5%"><col width="8%"><col width="6%"><col width="8%"><col width="5%"><col width="8%"></colgroup>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="3">Правка</td><td colspan="6">Стрела прогиба, мм на 1 м</td></tr>
<tr><td rowspan="4">на изменение нормы времени</td><td rowspan="4">легированная сталь</td><td rowspan="4">углеродиcтая сталь</td><td rowspan="4">цветные сплавы</td><td rowspan="4">в холодном состоянии</td><td rowspan="4">с предварительным подогревом</td><td rowspan="4">после газовой резки</td><td colspan="6">до правки</td></tr>
<tr><td colspan="2">до 15</td><td colspan="2">16 - 30</td><td colspan="2">св. 30</td></tr>
<tr><td colspan="6">после правки</td></tr>
<tr><td>&lt; 2</td><td>2 - 4</td><td>&lt; 2</td><td>2 - 4</td><td>&lt; 2</td><td>2 - 4</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,0</td><td>0,85</td><td>1,25</td><td>1,0</td><td>1,5</td><td>1,15</td></tr>
</table>


2. <a id="p100858"></a>Работа выполняется одним человеком при L <= 1500 мм и бригадой из двух человек при L > 1500 мм:

                          0,7    0,5
<a id="p100859"></a>           Т = 0,00796 х N    х L      для L <= 1500 мм  поз. 1...12;

                          0,7    0,7
<a id="p100860"></a>           Т = 0,00182 х N    х L      для > 1500 мм     поз. 1...12.


<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="11" rowspan="2">Калибровка обечаек в вальцах</td><td colspan="5">Правка</td></tr>
<tr><td colspan="5">Карта 20, лист 1</td></tr>
<tr><td colspan="16">Содержание работы</td></tr>
<tr><td colspan="16">1. Подать обечайку к вальцам. (рисунок не</td></tr>
<tr><td colspan="16">2. Установить обечайку в вальцы. приводится)</td></tr>
<tr><td colspan="16">3. Калибровать обечайку.</td></tr>
<tr><td colspan="16">4. Снять обечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="13">Толщина обечайки h, мм, до</td></tr>
<tr><td>обечайки</td><td>2</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td colspan="2">20</td><td>28</td><td>38</td><td>50</td><td>60</td></tr>
<tr><td>Д, мм, до</td><td>до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="6">300</td><td>100</td><td>0,74</td><td>0,91</td><td>1,04</td><td>1,27</td><td>1,46</td><td>1,79</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>300</td><td>1,04</td><td>1,27</td><td>1,47</td><td>1,79</td><td>2,06</td><td>2,51</td><td>2,71</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>400</td><td>1,14</td><td>1,39</td><td>1,60</td><td>1,95</td><td>2,25</td><td>2,96</td><td>3,05</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>550</td><td>1,26</td><td>1,54</td><td>1,77</td><td>2,16</td><td>2,48</td><td>3,03</td><td>3,27</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>800</td><td>1,41</td><td>1,73</td><td>1,99</td><td>2,42</td><td>2,79</td><td>3,40</td><td>3,67</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>1100</td><td>1,56</td><td>1,91</td><td>2,19</td><td>2,68</td><td>3,08</td><td>3,76</td><td>4,05</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td rowspan="2">400</td><td>100</td><td>0,89</td><td>1,09</td><td>1,25</td><td>1,52</td><td>1,76</td><td>2,14</td><td>2,31</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>300</td><td>1,25</td><td>1,53</td><td>1,76</td><td>2,14</td><td>2,47</td><td>3,01</td><td>3,25</td><td colspan="2">3,87</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="3%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="11" rowspan="2">Калибровка обечаек в вальцах</td><td colspan="5">Правка</td></tr>
<tr><td colspan="5">Карта 20, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="13">Толщина обечайки h, мм, до</td></tr>
<tr><td>обечайки</td><td>2</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td colspan="2">20</td><td>28</td><td>38</td><td>50</td><td>60</td></tr>
<tr><td>Д, мм, до</td><td>до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>9</td><td rowspan="5">400</td><td>400</td><td>1,37</td><td>1,67</td><td>1,92</td><td>2,34</td><td>2,70</td><td>3,29</td><td>3,55</td><td colspan="2">4,01</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>550</td><td>1,51</td><td>1,84</td><td>2,12</td><td>2,59</td><td>2,98</td><td>3,63</td><td>3,92</td><td colspan="2">4,67</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td>800</td><td>1,69</td><td>2,07</td><td>2,38</td><td>2,91</td><td>3,45</td><td>4,08</td><td>4,40</td><td colspan="2">5,20</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>1100</td><td>1,87</td><td>2,28</td><td>2,63</td><td>3,21</td><td>3,69</td><td>4,51</td><td>4,86</td><td colspan="2">5,79</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>1600</td><td>2,10</td><td>2,56</td><td>2,95</td><td>3,60</td><td>4,15</td><td>5,06</td><td>5,46</td><td colspan="2">6,50</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td rowspan="7">550</td><td>400</td><td>1,67</td><td>2,04</td><td>2,35</td><td>2,86</td><td>3,30</td><td>4,02</td><td>4,34</td><td colspan="2">5,17</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>550</td><td>1,85</td><td>2,25</td><td>2,59</td><td>3,16</td><td>3,64</td><td>4,44</td><td>4,79</td><td colspan="2">5,71</td><td>6,73</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>800</td><td>2,07</td><td>2,53</td><td>2,91</td><td>3,55</td><td>4,09</td><td>4,99</td><td>5,38</td><td colspan="2">6,41</td><td>7,50</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td>1100</td><td>2,29</td><td>2,79</td><td>3,21</td><td>3,92</td><td>4,51</td><td>5,51</td><td>5,94</td><td colspan="2">7,07</td><td>8,34</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td>1600</td><td>2,57</td><td>3,13</td><td>3,61</td><td>4,40</td><td>5,07</td><td>6,18</td><td>6,70</td><td colspan="2">7,94</td><td>9,37</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td>2300</td><td>2,82</td><td>3,51</td><td>4,04</td><td>4,93</td><td>5,67</td><td>6,92</td><td>7,46</td><td colspan="2">8,89</td><td>10,5</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>3200</td><td>3,19</td><td>3,89</td><td>4,48</td><td>5,46</td><td>6,28</td><td>7,67</td><td>8,27</td><td colspan="2">9,85</td><td>11,6</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>21</td><td rowspan="2">750</td><td>550</td><td>2,24</td><td>2,74</td><td>3,15</td><td>3,84</td><td>4,43</td><td>5,40</td><td>5,82</td><td colspan="2">6,94</td><td>8,18</td><td>9,50</td><td>10,9</td><td>11,9</td></tr>
<tr><td>22</td><td>800</td><td>2,52</td><td>3,07</td><td>3,54</td><td>4,32</td><td>4,97</td><td>6,06</td><td>6,54</td><td colspan="2">7,79</td><td>9,18</td><td>10,7</td><td>12,2</td><td>13,3</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="8%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="3%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="11" rowspan="2">Калибровка обечаек в вальцах</td><td colspan="5">Правка</td></tr>
<tr><td colspan="5">Карта 20, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="13">Толщина обечайки h, мм, до</td></tr>
<tr><td>обечайки</td><td>2</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td colspan="2">20</td><td>28</td><td>38</td><td>50</td><td>60</td></tr>
<tr><td>Д, мм, до</td><td>до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>23</td><td rowspan="4">750</td><td>1100</td><td>2,78</td><td>3,39</td><td>3,91</td><td>4,77</td><td>5,49</td><td>6,69</td><td>7,22</td><td colspan="2">8,60</td><td>10,1</td><td>11,8</td><td>13,5</td><td>14,7</td></tr>
<tr><td>24</td><td>1600</td><td>3,12</td><td>3,81</td><td>4,39</td><td>5,35</td><td>6,16</td><td>7,52</td><td>8,11</td><td colspan="2">9,66</td><td>11,4</td><td>13,2</td><td>15,1</td><td>16,5</td></tr>
<tr><td>25</td><td>2300</td><td>3,50</td><td>4,26</td><td>4,92</td><td>5,99</td><td>6,90</td><td>8,41</td><td>9,07</td><td colspan="2">10,8</td><td>12,7</td><td>14,8</td><td>16,9</td><td>18,5</td></tr>
<tr><td>26</td><td>3200</td><td>3,87</td><td>4,72</td><td>5,44</td><td>6,64</td><td>7,64</td><td>9,32</td><td>10,1</td><td colspan="2">11,8</td><td>14,2</td><td>16,4</td><td>18,8</td><td>20,5</td></tr>
<tr><td>27</td><td rowspan="6">1000</td><td>550</td><td>-</td><td>3,27</td><td>3,76</td><td>4,58</td><td>5,30</td><td>6,45</td><td>7,00</td><td colspan="2">8,28</td><td>9,78</td><td>11,3</td><td>12,9</td><td>14,2</td></tr>
<tr><td>28</td><td>800</td><td>-</td><td>3,69</td><td>4,24</td><td>5,18</td><td>5,96</td><td>7,27</td><td>7,84</td><td colspan="2">9,34</td><td>11,01</td><td>12,8</td><td>14,6</td><td>16,0</td></tr>
<tr><td>29</td><td>1100</td><td>-</td><td>4,07</td><td>4,68</td><td>5,71</td><td>6,58</td><td>8,02</td><td>8,65</td><td colspan="2">10,3</td><td>12,1</td><td>14,1</td><td>16,1</td><td>17,7</td></tr>
<tr><td>30</td><td>1600</td><td>-</td><td>4,57</td><td>5,26</td><td>6,42</td><td>7,39</td><td>9,01</td><td>9,72</td><td colspan="2">11,6</td><td>13,6</td><td>15,9</td><td>18,1</td><td>19,8</td></tr>
<tr><td>31</td><td>2300</td><td>-</td><td>5,11</td><td>5,89</td><td>7,18</td><td>8,27</td><td>10,1</td><td>10,9</td><td colspan="2">12,9</td><td>15,2</td><td>17,7</td><td>20,0</td><td>22,0</td></tr>
<tr><td>32</td><td>3200</td><td>-</td><td>5,66</td><td>6,52</td><td>7,96</td><td>9,16</td><td>11,2</td><td>12,0</td><td colspan="2">14,3</td><td>16,9</td><td>19,7</td><td>22,5</td><td>24,6</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="8%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="11" rowspan="2">Калибровка обечаек в вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 20, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="12">Толщина обечайки h, мм, до</td></tr>
<tr><td>обечайки</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td colspan="2">28</td><td>38</td><td>50</td><td>60</td></tr>
<tr><td>Д, мм, до</td><td>до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>33</td><td rowspan="6">1400</td><td>550</td><td>4,06</td><td>4,67</td><td>5,70</td><td>6,56</td><td>8,00</td><td>8,63</td><td>10,3</td><td colspan="2">12,1</td><td>14,1</td><td>16</td><td>17</td></tr>
<tr><td>34</td><td>800</td><td>4,56</td><td>5,25</td><td>6,40</td><td>7,37</td><td>8,99</td><td>9,69</td><td>11,5</td><td colspan="2">13,6</td><td>15,8</td><td>18</td><td>19</td></tr>
<tr><td>35</td><td>1100</td><td>5,03</td><td>5,79</td><td>7,06</td><td>8,13</td><td>9,92</td><td>10,7</td><td>12,7</td><td colspan="2">15,0</td><td>17,4</td><td>19</td><td>22</td></tr>
<tr><td>36</td><td>1600</td><td>5,65</td><td>6,50</td><td>7,93</td><td>9,13</td><td>11,1</td><td>12,0</td><td>14,3</td><td colspan="2">16,9</td><td>19,6</td><td>22</td><td>24</td></tr>
<tr><td>37</td><td>2300</td><td>6,32</td><td>7,28</td><td>8,88</td><td>10,2</td><td>12,4</td><td>13,4</td><td>16,0</td><td colspan="2">18,9</td><td>22,0</td><td>25</td><td>27</td></tr>
<tr><td>38</td><td>3200</td><td>7,0</td><td>8,06</td><td>9,83</td><td>11,3</td><td>13,8</td><td>14,9</td><td>17,7</td><td colspan="2">21,0</td><td>24,0</td><td>28</td><td>30</td></tr>
<tr><td>39</td><td rowspan="7">1800</td><td>800</td><td>-</td><td>6,15</td><td>7,50</td><td>8,63</td><td>10,5</td><td>11,3</td><td>13,5</td><td colspan="2">15,9</td><td>18,0</td><td>21</td><td>23</td></tr>
<tr><td>40</td><td>1100</td><td>-</td><td>6,78</td><td>8,27</td><td>9,53</td><td>11,6</td><td>12,5</td><td>14,9</td><td colspan="2">17,6</td><td>20,0</td><td>23</td><td>26</td></tr>
<tr><td>41</td><td>1600</td><td>-</td><td>7,62</td><td>9,27</td><td>10,7</td><td>13,0</td><td>14,1</td><td>16,8</td><td colspan="2">19,8</td><td>23,0</td><td>26</td><td>29</td></tr>
<tr><td>42</td><td>2300</td><td>-</td><td>8,53</td><td>10,4</td><td>14,6</td><td>15,7</td><td>16,2</td><td>18,8</td><td colspan="2">22,0</td><td>26,0</td><td>29</td><td>32</td></tr>
<tr><td>43</td><td>3200</td><td>-</td><td>9,45</td><td>11,5</td><td>13,3</td><td>16,2</td><td>17,4</td><td>21,0</td><td colspan="2">24,0</td><td>28,0</td><td>33</td><td>36</td></tr>
<tr><td>44</td><td>4600</td><td>-</td><td>10,6</td><td>12,9</td><td>14,8</td><td>18,1</td><td>19,5</td><td>23,0</td><td colspan="2">27,0</td><td>32,0</td><td>36</td><td>40</td></tr>
<tr><td>45</td><td>6500</td><td>-</td><td>11,8</td><td>14,3</td><td>16,5</td><td>20,0</td><td>22,0</td><td>26,0</td><td colspan="2">30,0</td><td>35,0</td><td>41</td><td>44</td></tr>
<tr><td>46</td><td>2400</td><td>800</td><td>-</td><td>7,37</td><td>8,99</td><td>10,3</td><td>12,6</td><td>13,6</td><td>16,2</td><td colspan="2">19,1</td><td>22,0</td><td>25</td><td>28</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="8%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="11" rowspan="2">Калибровка обечаек в вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 20, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="12">Толщина обечайки h, мм, до</td></tr>
<tr><td>обечайки</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td colspan="2">28</td><td>38</td><td>50</td><td>60</td></tr>
<tr><td>Д, мм, до</td><td>до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>47</td><td rowspan="6">2400</td><td>1100</td><td>-</td><td>8,13</td><td>9,92</td><td>11</td><td>14</td><td>15</td><td>18</td><td colspan="2">21</td><td>24</td><td>28</td><td>31</td></tr>
<tr><td>48</td><td>1600</td><td>-</td><td>9,13</td><td>11,1</td><td>13</td><td>16</td><td>16</td><td>20</td><td colspan="2">24</td><td>27</td><td>28</td><td>34</td></tr>
<tr><td>49</td><td>2300</td><td>-</td><td>10,2</td><td>12,5</td><td>14</td><td>18</td><td>19</td><td>22</td><td colspan="2">26</td><td>31</td><td>35</td><td>38</td></tr>
<tr><td>50</td><td>3200</td><td>-</td><td>11,3</td><td>13,8</td><td>16</td><td>19</td><td>21</td><td>25</td><td colspan="2">29</td><td>34</td><td>39</td><td>43</td></tr>
<tr><td>51</td><td>4600</td><td>-</td><td>12,7</td><td>15,5</td><td>18</td><td>22</td><td>23</td><td>28</td><td colspan="2">33</td><td>38</td><td>44</td><td>48</td></tr>
<tr><td>52</td><td>6500</td><td>-</td><td>14,1</td><td>17,2</td><td>20</td><td>24</td><td>26</td><td>31</td><td colspan="2">37</td><td>42</td><td>49</td><td>53</td></tr>
<tr><td>53</td><td rowspan="7">3200</td><td>1100</td><td>-</td><td>-</td><td>11,8</td><td>13</td><td>16</td><td>18</td><td>21</td><td colspan="2">25</td><td>29</td><td>34</td><td>37</td></tr>
<tr><td>54</td><td>1600</td><td>-</td><td>-</td><td>13,3</td><td>15</td><td>18</td><td>20</td><td>24</td><td colspan="2">28</td><td>33</td><td>38</td><td>41</td></tr>
<tr><td>55</td><td>2300</td><td>-</td><td>-</td><td>14,9</td><td>17</td><td>21</td><td>23</td><td>27</td><td colspan="2">32</td><td>37</td><td>42</td><td>46</td></tr>
<tr><td>56</td><td>3200</td><td>-</td><td>-</td><td>16,5</td><td>19</td><td>23</td><td>25</td><td>30</td><td colspan="2">35</td><td>41</td><td>47</td><td>51</td></tr>
<tr><td>57</td><td>4600</td><td>-</td><td>-</td><td>18,5</td><td>21</td><td>26</td><td>28</td><td>33</td><td colspan="2">39</td><td>46</td><td>52</td><td>57</td></tr>
<tr><td>58</td><td>6500</td><td>-</td><td>-</td><td>20,0</td><td>24</td><td>29</td><td>31</td><td>37</td><td colspan="2">44</td><td>51</td><td>58</td><td>64</td></tr>
<tr><td>59</td><td>8000</td><td>-</td><td>-</td><td>22,0</td><td>25</td><td>31</td><td>33</td><td>40</td><td colspan="2">48</td><td>54</td><td>62</td><td>68</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="8%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="11" rowspan="2">Калибровка обечаек в вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 20, лист 6</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="12">Толщина обечайки h, мм, до</td></tr>
<tr><td>обечайки</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td colspan="2">28</td><td>38</td><td>50</td><td>60</td></tr>
<tr><td>Д, мм, до</td><td>до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>60</td><td rowspan="7">4000</td><td>1100</td><td>-</td><td>-</td><td>13,7</td><td>15</td><td>19</td><td>21</td><td>25</td><td colspan="2">29</td><td>34</td><td>38</td><td>42</td></tr>
<tr><td>61</td><td>1600</td><td>-</td><td>-</td><td>15,4</td><td>17</td><td>21</td><td>23</td><td>28</td><td colspan="2">33</td><td>38</td><td>43</td><td>47</td></tr>
<tr><td>62</td><td>2300</td><td>-</td><td>-</td><td>17,2</td><td>20</td><td>24</td><td>26</td><td>31</td><td colspan="2">37</td><td>42</td><td>49</td><td>53</td></tr>
<tr><td>63</td><td>3200</td><td>-</td><td>-</td><td>19,1</td><td>22</td><td>27</td><td>29</td><td>34</td><td colspan="2">40</td><td>47</td><td>54</td><td>59</td></tr>
<tr><td>64</td><td>4600</td><td>-</td><td>-</td><td>21,0</td><td>24</td><td>30</td><td>32</td><td>38</td><td colspan="2">45</td><td>53</td><td>60</td><td>66</td></tr>
<tr><td>65</td><td>6500</td><td>-</td><td>-</td><td>24,0</td><td>27</td><td>33</td><td>36</td><td>43</td><td colspan="2">50</td><td>59</td><td>67</td><td>73</td></tr>
<tr><td>66</td><td>8000</td><td>-</td><td>-</td><td>25,0</td><td>29</td><td>35</td><td>38</td><td>46</td><td colspan="2">54</td><td>62</td><td>71</td><td>78</td></tr>
<tr><td>67</td><td rowspan="6">5000</td><td>1100</td><td>-</td><td>-</td><td>16,1</td><td>18</td><td>22</td><td>24</td><td>28</td><td colspan="2">33</td><td>39</td><td>44</td><td>49</td></tr>
<tr><td>68</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>20</td><td>25</td><td>27</td><td>32</td><td colspan="2">38</td><td>44</td><td>50</td><td>55</td></tr>
<tr><td>69</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>23</td><td>28</td><td>30</td><td>36</td><td colspan="2">42</td><td>49</td><td>56</td><td>61</td></tr>
<tr><td>70</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>25</td><td>31</td><td>33</td><td>39</td><td colspan="2">47</td><td>54</td><td>62</td><td>68</td></tr>
<tr><td>71</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>28</td><td>34</td><td>37</td><td>44</td><td colspan="2">52</td><td>61</td><td>69</td><td>76</td></tr>
<tr><td>72</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>31</td><td>38</td><td>41</td><td>49</td><td colspan="2">58</td><td>67</td><td>77</td><td>84</td></tr>
<tr><td>73</td><td></td><td>8000</td><td>-</td><td>-</td><td>-</td><td>33</td><td>41</td><td>44</td><td>52</td><td colspan="2">62</td><td>72</td><td>82</td><td>90</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="8%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="11" rowspan="2">Калибровка обечаек в вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 20, лист 7</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="12">Толщина обечайки h, мм, до</td></tr>
<tr><td>обечайки</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td colspan="2">28</td><td>38</td><td>50</td><td>60</td></tr>
<tr><td>Д, мм, до</td><td>до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>74</td><td rowspan="7">6000</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>-</td><td>25</td><td>27</td><td>32</td><td colspan="2">37</td><td>44</td><td>50</td><td>55</td></tr>
<tr><td>75</td><td>1600</td><td>-</td><td>_</td><td>-</td><td>-</td><td>28</td><td>30</td><td>36</td><td colspan="2">42</td><td>49</td><td>57</td><td>61</td></tr>
<tr><td>76</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>-</td><td>31</td><td>34</td><td>40</td><td colspan="2">47</td><td>55</td><td>63</td><td>69</td></tr>
<tr><td>77</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>-</td><td>34</td><td>37</td><td>44</td><td colspan="2">52</td><td>61</td><td>69</td><td>76</td></tr>
<tr><td>78</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>-</td><td>39</td><td>42</td><td>50</td><td colspan="2">59</td><td>68</td><td>77</td><td>85</td></tr>
<tr><td>79</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>-</td><td>43</td><td>46</td><td>55</td><td colspan="2">65</td><td>76</td><td>87</td><td>95</td></tr>
<tr><td>80</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>-</td><td>46</td><td>49</td><td>59</td><td colspan="2">69</td><td>81</td><td>92</td><td>101</td></tr>
<tr><td>81</td><td rowspan="7">7000</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>29</td><td>35</td><td colspan="2">41</td><td>48</td><td>55</td><td>60</td></tr>
<tr><td>82</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>33</td><td>39</td><td colspan="2">46</td><td>54</td><td>62</td><td>68</td></tr>
<tr><td>83</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>37</td><td>44</td><td colspan="2">52</td><td>60</td><td>69</td><td>76</td></tr>
<tr><td>84</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>41</td><td>49</td><td colspan="2">58</td><td>67</td><td>77</td><td>84</td></tr>
<tr><td>85</td><td>4600</td><td>_</td><td>-</td><td>-</td><td>-</td><td>-</td><td>46</td><td>55</td><td colspan="2">64</td><td>75</td><td>86</td><td>94</td></tr>
<tr><td>86</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>51</td><td>61</td><td colspan="2">72</td><td>83</td><td>95</td><td>104</td></tr>
<tr><td>87</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>54</td><td>65</td><td colspan="2">77</td><td>89</td><td>102</td><td>111</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="73%"><col width="27%"></colgroup>
<tr><td rowspan="2">Калибровка обечаек в вальцах</td><td>Правка</td></tr>
<tr><td>Карта 20, лист 8</td></tr>
</table>


<a id="p100983"></a>Примечания: 1. При измененных условиях калибровки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="15%"><col width="14%"><col width="11%"><col width="15%"><col width="15%"><col width="15%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="3">Материал</td><td colspan="3">Скорость вращения валков, м/мин.</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>до 6</td><td>7 - 8</td><td>св. 8</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,1</td><td>1,0</td><td>0,9</td></tr>
</table>


2. <a id="p100986"></a>Работа выполняется бригадой из двух человек:

                                   0,63    0,31    0,49
<a id="p100987"></a>                    Т = 0,00349 х Д     х L     х h    .


<table>
<colgroup><col width="11%"><col width="12%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Калибровка обечаек в горячем состоянии в вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 21, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Загрузить обечайку в нагревательную печь. (рисунок не</td></tr>
<tr><td colspan="12">2. Выгрузить обечайку из печи, подать к вальцам. приводится)</td></tr>
<tr><td colspan="12">3. Установить обечайку в вальцы.</td></tr>
<tr><td colspan="12">4. Калибровать обечайку.</td></tr>
<tr><td colspan="12">5. Снять обечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td>Длина обечайки</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">L, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td colspan="2">65</td><td>80</td><td>105</td><td>130</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="7">550</td><td>400</td><td>3,9</td><td>4,8</td><td>5,8</td><td>6,9</td><td colspan="2">8,1</td><td>9,2</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>550</td><td>4,4</td><td>5,4</td><td>6,6</td><td>7,8</td><td colspan="2">9,1</td><td>10,3</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>800</td><td>5,1</td><td>6,3</td><td>7,6</td><td>8,9</td><td colspan="2">10,5</td><td>11,9</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>1100</td><td>5,8</td><td>7,1</td><td>8,5</td><td>10,1</td><td colspan="2">11,8</td><td>13,4</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>1600</td><td>6,7</td><td>8,2</td><td>9,8</td><td>11,6</td><td colspan="2">13,7</td><td>15,5</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>2300</td><td>7,6</td><td>9,4</td><td>11,3</td><td>13,4</td><td colspan="2">15,7</td><td>17,8</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>3200</td><td>8,7</td><td>10,6</td><td>12,8</td><td>15,1</td><td colspan="2">17,8</td><td>20,2</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="12%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Калибровка обечаек в горячем состоянии в вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 21, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td>Длина обечайки</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">L, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td colspan="2">65</td><td>80</td><td>105</td><td>130</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>8</td><td rowspan="6">750</td><td>550</td><td>5,6</td><td>6,8</td><td>8,3</td><td>9,8</td><td colspan="2">11,5</td><td>13,0</td><td>15,4</td><td></td></tr>
<tr><td>9</td><td>800</td><td>6,5</td><td>7,9</td><td>9,5</td><td>11,3</td><td colspan="2">13,2</td><td>15,0</td><td>17,7</td><td>-</td></tr>
<tr><td>10</td><td>1100</td><td>7,3</td><td>8,9</td><td>10,8</td><td>12,7</td><td colspan="2">14,9</td><td>17,0</td><td>20,0</td><td>-</td></tr>
<tr><td>11</td><td>1600</td><td>8,4</td><td>10,3</td><td>12,4</td><td>14,7</td><td colspan="2">17,2</td><td>19,6</td><td>23,1</td><td>-</td></tr>
<tr><td>12</td><td>2300</td><td>9,6</td><td>11,8</td><td>14,3</td><td>16,9</td><td colspan="2">19,8</td><td>22,5</td><td>26,5</td><td>-</td></tr>
<tr><td>13</td><td>3200</td><td>10,9</td><td>13,4</td><td>16,2</td><td>19,1</td><td colspan="2">22,4</td><td>25,5</td><td>30,0</td><td>-</td></tr>
<tr><td>14</td><td rowspan="6">1000</td><td>550</td><td>6,9</td><td>8,5</td><td>10,3</td><td>12,1</td><td colspan="2">14,3</td><td>16,2</td><td>19,1</td><td>21,8</td></tr>
<tr><td>15</td><td>800</td><td>8,0</td><td>9,8</td><td>11,8</td><td>14,0</td><td colspan="2">16,4</td><td>18,7</td><td>22,0</td><td>25,1</td></tr>
<tr><td>16</td><td>1100</td><td>9,0</td><td>11,1</td><td>13,4</td><td>15,8</td><td colspan="2">18,5</td><td>21,1</td><td>24,8</td><td>28,3</td></tr>
<tr><td>17</td><td>1600</td><td>10,4</td><td>12,8</td><td>15,4</td><td>18,2</td><td colspan="2">21,4</td><td>24,3</td><td>28,7</td><td>-</td></tr>
<tr><td>18</td><td>2300</td><td>12,0</td><td>14,7</td><td>17,7</td><td>20,9</td><td colspan="2">24,5</td><td>27,9</td><td>32,9</td><td>-</td></tr>
<tr><td>19</td><td>3200</td><td>13,6</td><td>16,6</td><td>20,1</td><td>23,7</td><td colspan="2">27,8</td><td>31,6</td><td>37,3</td><td>42,5</td></tr>
<tr><td>20</td><td>1400</td><td>550</td><td>8,9</td><td>11,0</td><td>13,2</td><td>15,6</td><td colspan="2">18,3</td><td>20,8</td><td>24,6</td><td>28,0</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="12%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Калибровка обечаек в горячем состоянии в вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 21, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td>Длина обечайки</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">L, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td colspan="2">65</td><td>80</td><td>105</td><td>130</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>21</td><td rowspan="5">1400</td><td>800</td><td>10,3</td><td>12,7</td><td>15,2</td><td>18,0</td><td colspan="2">21,1</td><td>24,0</td><td>28,3</td><td>32,3</td></tr>
<tr><td>22</td><td>1100</td><td>11,6</td><td>14,3</td><td>17,2</td><td>20,3</td><td colspan="2">23,9</td><td>27,1</td><td>32,0</td><td>36,4</td></tr>
<tr><td>23</td><td>1600</td><td>13,4</td><td>16,5</td><td>19,8</td><td>23,5</td><td colspan="2">27,5</td><td>31,2</td><td>36,9</td><td>42,0</td></tr>
<tr><td>24</td><td>2300</td><td>15,4</td><td>18,9</td><td>22,8</td><td>26,9</td><td colspan="2">31,6</td><td>35,9</td><td>42,3</td><td>-</td></tr>
<tr><td>25</td><td>3200</td><td>17,5</td><td>21,4</td><td>25,8</td><td>30,5</td><td colspan="2">35,8</td><td>40,7</td><td>48,0</td><td>-</td></tr>
<tr><td>26</td><td rowspan="7">1800</td><td>800</td><td>12,4</td><td>15,3</td><td>18,4</td><td>21,8</td><td colspan="2">25,5</td><td>29,0</td><td>34,2</td><td>39,0</td></tr>
<tr><td>27</td><td>1100</td><td>14,0</td><td>17,2</td><td>20,8</td><td>24,6</td><td colspan="2">28,8</td><td>32,7</td><td>38,6</td><td>44,0</td></tr>
<tr><td>28</td><td>1600</td><td>16,2</td><td>19,9</td><td>24,0</td><td>28,3</td><td colspan="2">33,2</td><td>37,7</td><td>44,5</td><td>50,7</td></tr>
<tr><td>29</td><td>2600</td><td>19,5</td><td>23,9</td><td>28,8</td><td>34,1</td><td colspan="2">40,0</td><td>45,4</td><td>53,5</td><td>-</td></tr>
<tr><td>30</td><td>3200</td><td>21,1</td><td>25,9</td><td>31,2</td><td>36,8</td><td colspan="2">43,2</td><td>49,1</td><td>57,9</td><td>-</td></tr>
<tr><td>31</td><td>4600</td><td>24,2</td><td>29,7</td><td>35,8</td><td>42,3</td><td colspan="2">49,6</td><td>56,3</td><td>-</td><td>-</td></tr>
<tr><td>32</td><td>6500</td><td>27,6</td><td>33,9</td><td>40,8</td><td>48,2</td><td colspan="2">56,6</td><td>64,3</td><td>-</td><td>-</td></tr>
<tr><td>33</td><td rowspan="2">2400</td><td>800</td><td>15,4</td><td>19,0</td><td>22,8</td><td>27,0</td><td colspan="2">31,7</td><td>36,0</td><td>42,5</td><td>48,4</td></tr>
<tr><td>34</td><td>1100</td><td>17,4</td><td>21,4</td><td>25,8</td><td>30,5</td><td colspan="2">35,8</td><td>40,6</td><td>47,9</td><td>54,6</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="12%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Калибровка обечаек в горячем состоянии в вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 21, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td>Длина обечайки</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">L, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td colspan="2">65</td><td>80</td><td>105</td><td>130</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>35</td><td rowspan="5">2400</td><td>1600</td><td>20,1</td><td>24,7</td><td>29,7</td><td>35,1</td><td colspan="2">41,2</td><td>46,8</td><td>55,2</td><td>62,9</td></tr>
<tr><td>36</td><td>2600</td><td>24,2</td><td>29,7</td><td>35,7</td><td>42,3</td><td colspan="2">49,6</td><td>56,3</td><td>66,4</td><td>-</td></tr>
<tr><td>37</td><td>3200</td><td>26,1</td><td>32,1</td><td>38,7</td><td>45,7</td><td colspan="2">53,7</td><td>60,9</td><td>71,9</td><td>-</td></tr>
<tr><td>38</td><td>4600</td><td>30,0</td><td>36,8</td><td>44,4</td><td>52,5</td><td colspan="2">61,6</td><td>69,9</td><td>-</td><td>-</td></tr>
<tr><td>39</td><td>6500</td><td>34,2</td><td>42,0</td><td>50,6</td><td>59,9</td><td colspan="2">70,2</td><td>79,7</td><td>-</td><td>-</td></tr>
<tr><td>40</td><td rowspan="7">3200</td><td>1100</td><td>21,6</td><td>26,5</td><td>32,0</td><td>37,8</td><td colspan="2">44,4</td><td>50,4</td><td>59,4</td><td>67,7</td></tr>
<tr><td>41</td><td>1600</td><td>24,9</td><td>30,6</td><td>36,9</td><td>43,6</td><td colspan="2">51,2</td><td>58,1</td><td>68,5</td><td>78,1</td></tr>
<tr><td>42</td><td>2300</td><td>28,6</td><td>35,1</td><td>42,3</td><td>50,0</td><td colspan="2">58,7</td><td>66,7</td><td>78,7</td><td>-</td></tr>
<tr><td>43</td><td>3200</td><td>32,4</td><td>39,8</td><td>48,0</td><td>56,7</td><td colspan="2">66,6</td><td>75,6</td><td>89,2</td><td>-</td></tr>
<tr><td>44</td><td>4600</td><td>37,2</td><td>45,7</td><td>55,1</td><td>66,1</td><td colspan="2">76,4</td><td>86,7</td><td>-</td><td>-</td></tr>
<tr><td>45</td><td>6500</td><td>42,5</td><td>52,1</td><td>62,8</td><td>74,3</td><td colspan="2">87,2</td><td>98,9</td><td>-</td><td>-</td></tr>
<tr><td>46</td><td>8000</td><td>46,0</td><td>56,4</td><td>68,0</td><td>80,4</td><td colspan="2">94,3</td><td>107,0</td><td>-</td><td>-</td></tr>
<tr><td>47</td><td>4000</td><td>1100</td><td>25,6</td><td>31,4</td><td>37,8</td><td>44,7</td><td colspan="2">52,5</td><td>59,5</td><td>70,3</td><td>80,1</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="12%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Калибровка обечаек в горячем состоянии в вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 21, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td>Длина обечайки</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">L, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td colspan="2">65</td><td>80</td><td>105</td><td>130</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>48</td><td rowspan="6">4000</td><td>1600</td><td>29,5</td><td>36,2</td><td>43,6</td><td>51,5</td><td colspan="2">60,5</td><td>68,6</td><td>81,0</td><td>92,3</td></tr>
<tr><td>49</td><td>2300</td><td>33,8</td><td>41,5</td><td>50,0</td><td>59,2</td><td colspan="2">69,4</td><td>78,8</td><td>93,0</td><td>-</td></tr>
<tr><td>50</td><td>3200</td><td>38,4</td><td>47,1</td><td>56,7</td><td>67,1</td><td colspan="2">78,7</td><td>89,3</td><td>105,5</td><td>-</td></tr>
<tr><td>51</td><td>4600</td><td>44,0</td><td>54,1</td><td>65,1</td><td>77,0</td><td colspan="2">90,3</td><td>102,5</td><td>-</td><td>-</td></tr>
<tr><td>52</td><td>6500</td><td>50,2</td><td>61,6</td><td>74,3</td><td>87,8</td><td colspan="2">103,0</td><td>116,9</td><td>-</td><td>-</td></tr>
<tr><td>53</td><td>8000</td><td>54,3</td><td>66,7</td><td>80,4</td><td>95,0</td><td colspan="2">111,5</td><td>126,5</td><td>-</td><td>-</td></tr>
<tr><td>54</td><td rowspan="7">5000</td><td>1100</td><td>30,2</td><td>37,1</td><td>44,7</td><td>52,8</td><td colspan="2">62,0</td><td>70,4</td><td>83,1</td><td>94,6</td></tr>
<tr><td>55</td><td>1600</td><td>34,8</td><td>42,8</td><td>51,5</td><td>60,9</td><td colspan="2">71,5</td><td>81,2</td><td>95,8</td><td>-</td></tr>
<tr><td>56</td><td>2300</td><td>40,0</td><td>49,1</td><td>59,2</td><td>69,9</td><td colspan="2">82,1</td><td>93,2</td><td>110,0</td><td>-</td></tr>
<tr><td>57</td><td>3200</td><td>45,3</td><td>55,7</td><td>67,1</td><td>79,3</td><td colspan="2">93,0</td><td>105,6</td><td>-</td><td>-</td></tr>
<tr><td>58</td><td>4600</td><td>52,0</td><td>63,9</td><td>77,0</td><td>91,0</td><td colspan="2">106,8</td><td>121,2</td><td>-</td><td>-</td></tr>
<tr><td>59</td><td>6500</td><td>59,3</td><td>72,9</td><td>87,8</td><td>103,8</td><td colspan="2">121,8</td><td>138,2</td><td>-</td><td>-</td></tr>
<tr><td>60</td><td>8000</td><td>64,2</td><td>78,9</td><td>95,0</td><td>112,3</td><td colspan="2">131,8</td><td>149,6</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="12%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Калибровка обечаек в горячем состоянии в вальцах</td><td colspan="4">Правка</td></tr>
<tr><td colspan="4">Карта 21, лист 6</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td>Длина обечайки</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">L, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td colspan="2">65</td><td>80</td><td>105</td><td>130</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>61</td><td rowspan="7">6000</td><td>1100</td><td>34,6</td><td>42,5</td><td>51,2</td><td>60,6</td><td colspan="2">71,7</td><td>80,7</td><td>95,3</td><td>108,5</td></tr>
<tr><td>62</td><td>1600</td><td>39,9</td><td>49,0</td><td>59,1</td><td>69,9</td><td colspan="2">82,0</td><td>93,0</td><td>109,8</td><td>-</td></tr>
<tr><td>63</td><td>2300</td><td>45,8</td><td>56,3</td><td>67,8</td><td>80,2</td><td colspan="2">94,1</td><td>106,8</td><td>126,1</td><td>-</td></tr>
<tr><td>64</td><td>3200</td><td>52,0</td><td>63,8</td><td>76,9</td><td>90,9</td><td colspan="2">106,7</td><td>121,1</td><td>-</td><td>-</td></tr>
<tr><td>65</td><td>4600</td><td>59,7</td><td>73,3</td><td>88,3</td><td>104,3</td><td colspan="2">122,5</td><td>139,0</td><td>-</td><td>-</td></tr>
<tr><td>66</td><td>6500</td><td>68,0</td><td>83,5</td><td>100,7</td><td>119,0</td><td colspan="2">139,6</td><td>158,5</td><td>-</td><td>-</td></tr>
<tr><td>67</td><td>8000</td><td>73,6</td><td>90,4</td><td>108,9</td><td>128,8</td><td colspan="2">151,1</td><td>171,5</td><td>-</td><td>-</td></tr>
<tr><td>68</td><td rowspan="7">7000</td><td>1100</td><td>38,9</td><td>47,7</td><td>57,5</td><td>68,0</td><td colspan="2">79,8</td><td>90,6</td><td>106,9</td><td>121,8</td></tr>
<tr><td>69</td><td>1600</td><td>44,8</td><td>55,1</td><td>66,3</td><td>78,4</td><td colspan="2">92,0</td><td>104,4</td><td>123,3</td><td>140,4</td></tr>
<tr><td>70</td><td>2300</td><td>51,5</td><td>63,2</td><td>76,1</td><td>90,0</td><td colspan="2">105,6</td><td>119,9</td><td>141,5</td><td>-</td></tr>
<tr><td>71</td><td>3200</td><td>58,4</td><td>71,6</td><td>86,3</td><td>102,0</td><td colspan="2">119,8</td><td>135,9</td><td>-</td><td>-</td></tr>
<tr><td>72</td><td>4600</td><td>67,0</td><td>82,2</td><td>99,1</td><td>117,1</td><td colspan="2">137,5</td><td>156,0</td><td>-</td><td>-</td></tr>
<tr><td>73</td><td>6500</td><td>76,4</td><td>93,8</td><td>113,0</td><td>133,6</td><td colspan="2">156,8</td><td>177,9</td><td>-</td><td>-</td></tr>
<tr><td>74</td><td>8000</td><td>82,7</td><td>101,5</td><td>122,3</td><td>144,5</td><td colspan="2">169,6</td><td>192,5</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="72%"><col width="28%"></colgroup>
<tr><td rowspan="2">Калибровка обечаек в горячем состоянии в вальцах</td><td>Правка</td></tr>
<tr><td>Карта 21, лист 7</td></tr>
</table>


<a id="p101094"></a>Примечания: 1. При измененных условиях калибровки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="35%"><col width="22%"><col width="22%"><col width="22%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Скорость вращения валков, м/мин.</td></tr>
<tr><td>до 6</td><td>7 - 8</td><td>св. 8</td></tr>
<tr><td>Коэффициент</td><td>1,1</td><td>1,0</td><td>0,9</td></tr>
</table>


2. <a id="p101097"></a>Работа выполняется бригадой из двух человек:

                                     0,75    0,38    0,61
<a id="p101098"></a>                     Т = 0,000571 х Д     х L     х h    .


#### <a id="p101099"></a>Раздел 3. НОРМАТИВЫ ШТУЧНОГО ВРЕМЕНИ НА ГИБКУ ДЕТАЛЕЙ



<table>
<colgroup><col width="7%"><col width="7%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Подгибка кромок листов в вальцах</td><td colspan="5">Гибка</td></tr>
<tr><td colspan="5">Карта 22, лист 1</td></tr>
<tr><td colspan="18">Содержание работы</td></tr>
<tr><td colspan="18">1. Подать лист к вальцам. (рисунок не</td></tr>
<tr><td colspan="18">2. Установить подкладной лист. приводится)</td></tr>
<tr><td colspan="18">3. Установить лист в вальцы на подкладной лист.</td></tr>
<tr><td colspan="18">4. Подогнуть кромку.</td></tr>
<tr><td colspan="18">5. Повернуть лист на 180° и установить в вальцы на подкладной лист.</td></tr>
<tr><td colspan="18">6. Подогнуть вторую кромку.</td></tr>
<tr><td colspan="18">7. Снять лист, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина листа</td><td>Толщина листа</td><td colspan="15">Ширина подгибаемой кромки В, мм, до</td></tr>
<tr><td>L, мм,</td><td rowspan="2">h, мм, до</td><td>150</td><td>300</td><td>400</td><td>500</td><td>650</td><td>850</td><td>1100</td><td>1500</td><td>2000</td><td colspan="2">2600</td><td>3500</td><td>4600</td><td>6000</td><td>8000</td></tr>
<tr><td>до</td><td colspan="15">Время на лист Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">1000</td><td>4</td><td>0,32</td><td>0,53</td><td>0,65</td><td>0,86</td><td>0,91</td><td>1,1</td><td>1,31</td><td>1,63</td><td>1,99</td><td colspan="2">2,40</td><td>2,96</td><td>3,58</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>6</td><td>0,40</td><td>0,65</td><td>0,79</td><td>0,93</td><td>1,11</td><td>1,34</td><td>1,61</td><td>2,00</td><td>2,45</td><td colspan="2">2,95</td><td>3,63</td><td>4,39</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>8</td><td>0,44</td><td>0,72</td><td>0,88</td><td>1,03</td><td>1,24</td><td>1,49</td><td>1,78</td><td>2,22</td><td>2,72</td><td colspan="2">3,26</td><td>4,02</td><td>4,87</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>10</td><td>0,49</td><td>0,79</td><td>0,97</td><td>1,14</td><td>1,37</td><td>1,65</td><td>1,98</td><td>2,46</td><td>3,02</td><td colspan="2">3,62</td><td>4,46</td><td>5,40</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="6%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"></colgroup>
<tr><td colspan="13" rowspan="2">Подгибка кромок листов в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 22, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина листа</td><td>Толщина листа</td><td colspan="14">Ширина подгибаемой кромки В, мм, до</td></tr>
<tr><td>L, мм,</td><td rowspan="2">h, мм, до</td><td>150</td><td>300</td><td>400</td><td>500</td><td>650</td><td>850</td><td>1100</td><td>1500</td><td>2000</td><td>2600</td><td>3500</td><td>4600</td><td>6000</td><td>8000</td></tr>
<tr><td>до</td><td colspan="14">Время на лист Т, чел.-мин.</td></tr>
<tr><td>5</td><td rowspan="6">1000</td><td>14</td><td>0,57</td><td>0,93</td><td>1,13</td><td>1,32</td><td>1,59</td><td>1,92</td><td>2,31</td><td>2,86</td><td>3,50</td><td>4,20</td><td>5,20</td><td>6,30</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>20</td><td>0,67</td><td>1,09</td><td>1,33</td><td>1,56</td><td>1,87</td><td>2,25</td><td>2,70</td><td>3,36</td><td>4,11</td><td>4,90</td><td>6,08</td><td>7,36</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>30</td><td>0,81</td><td>1,31</td><td>1,6</td><td>1,87</td><td>2,25</td><td>2,72</td><td>3,25</td><td>4,05</td><td>4,95</td><td>5,95</td><td>7,32</td><td>8,87</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>40</td><td>0,92</td><td>1,49</td><td>1,82</td><td>2,13</td><td>2,56</td><td>3,09</td><td>3,7</td><td>4,6</td><td>5,6</td><td>6,75</td><td>8,32</td><td>10,07</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>50</td><td>1,01</td><td>1,64</td><td>2,01</td><td>2,36</td><td>2,83</td><td>3,41</td><td>4,09</td><td>5,08</td><td>6,22</td><td>7,47</td><td>9,19</td><td>11,14</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>60</td><td>1,10</td><td>1,79</td><td>2,18</td><td>2,55</td><td>3,07</td><td>3,70</td><td>4,44</td><td>5,51</td><td>6,75</td><td>8,11</td><td>9,98</td><td>12,09</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td rowspan="8">1500</td><td>4</td><td>0,37</td><td>0,61</td><td>0,74</td><td>0,86</td><td>1,04</td><td>1,25</td><td>1,5</td><td>1,87</td><td>2,29</td><td>2,75</td><td>3,38</td><td>4,10</td><td>4,90</td><td>-</td></tr>
<tr><td>12</td><td>6</td><td>0,46</td><td>0,75</td><td>0,91</td><td>1,07</td><td>1,28</td><td>1,55</td><td>1,86</td><td>2,31</td><td>2,82</td><td>3,39</td><td>4,17</td><td>5,05</td><td>6,08</td><td>-</td></tr>
<tr><td>13</td><td>8</td><td>0,51</td><td>0,83</td><td>1,01</td><td>1,18</td><td>1,42</td><td>1,72</td><td>2,06</td><td>2,55</td><td>3,12</td><td>3,76</td><td>4,6</td><td>5,60</td><td>6,75</td><td>-</td></tr>
<tr><td>14</td><td>10</td><td>0,56</td><td>0,91</td><td>1,12</td><td>1,31</td><td>1,57</td><td>1,89</td><td>2,27</td><td>2,82</td><td>3,46</td><td>4,15</td><td>5,11</td><td>6,19</td><td>7,46</td><td>-</td></tr>
<tr><td>15</td><td>14</td><td>0,66</td><td>1,07</td><td>1,31</td><td>1,53</td><td>1,83</td><td>2,21</td><td>2,65</td><td>3,29</td><td>4,03</td><td>4,84</td><td>5,96</td><td>7,20</td><td>8,70</td><td>-</td></tr>
<tr><td>16</td><td>20</td><td>0,77</td><td>1,25</td><td>1,53</td><td>1,79</td><td>2,15</td><td>2,59</td><td>3,1</td><td>3,86</td><td>5,68</td><td>7,0</td><td>8,46</td><td>10,20</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td>30</td><td>0,92</td><td>1,51</td><td>1,84</td><td>2,15</td><td>2,58</td><td>3,12</td><td>3,73</td><td>4,65</td><td>5,68</td><td>6,82</td><td>8,40</td><td>10,20</td><td>12,20</td><td>-</td></tr>
<tr><td>18</td><td>40</td><td>1,05</td><td>1,71</td><td>2,09</td><td>2,44</td><td>2,94</td><td>3,55</td><td>4,25</td><td>5,28</td><td>6,46</td><td>7,77</td><td>9,60</td><td>11,60</td><td>13,90</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="6%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"></colgroup>
<tr><td colspan="13" rowspan="2">Подгибка кромок листов в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 22, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина листа</td><td>Толщина листа</td><td colspan="14">Ширина подгибаемой кромки В, мм, до</td></tr>
<tr><td>L, мм,</td><td rowspan="2">h, мм, до</td><td>150</td><td>300</td><td>400</td><td>500</td><td>650</td><td>850</td><td>1100</td><td>1500</td><td>2000</td><td>2600</td><td>3500</td><td>4600</td><td>6000</td><td>8000</td></tr>
<tr><td>до</td><td colspan="14">Время на лист Т, чел.-мин.</td></tr>
<tr><td>19</td><td rowspan="2">1500</td><td>50</td><td>1,16</td><td>1,89</td><td>2,31</td><td>2,7</td><td>3,25</td><td>3,92</td><td>4,69</td><td>5,84</td><td>7,14</td><td>8,58</td><td>10,6</td><td>12,80</td><td>15,40</td><td>-</td></tr>
<tr><td>20</td><td>60</td><td>1,26</td><td>2,05</td><td>2,51</td><td>2,93</td><td>3,53</td><td>4,26</td><td>5,1</td><td>6,34</td><td>7,75</td><td>9,31</td><td>11,5</td><td>13,9</td><td>16,7</td><td>-</td></tr>
<tr><td>21</td><td rowspan="11">2000</td><td>4</td><td>0,41</td><td>0,67</td><td>0,82</td><td>0,96</td><td>1,15</td><td>1,39</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>22</td><td>6</td><td>0,46</td><td>0,74</td><td>0,91</td><td>1,06</td><td>1,28</td><td>1,54</td><td>1,84</td><td>2,29</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>23</td><td>8</td><td>0,56</td><td>0,92</td><td>1,12</td><td>1,31</td><td>1,57</td><td>1,89</td><td>2,27</td><td>2,82</td><td>3,45</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>24</td><td>10</td><td>0,62</td><td>1,01</td><td>1,24</td><td>1,45</td><td>1,74</td><td>2,1</td><td>2,51</td><td>3,12</td><td>3,82</td><td>4,6</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>25</td><td>14</td><td>0,72</td><td>1,18</td><td>1,44</td><td>1,68</td><td>2,02</td><td>2,44</td><td>2,92</td><td>3,63</td><td>4,44</td><td>5,33</td><td>6,57</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>26</td><td>20</td><td>0,85</td><td>1,38</td><td>1,69</td><td>1,98</td><td>2,37</td><td>2,86</td><td>3,43</td><td>4,26</td><td>5,21</td><td>6,27</td><td>7,72</td><td>9,34</td><td>-</td><td>-</td></tr>
<tr><td>27</td><td>30</td><td>1,02</td><td>1,66</td><td>2,03</td><td>2,37</td><td>2,85</td><td>3,43</td><td>4,11</td><td>5,11</td><td>6,25</td><td>7,52</td><td>9,26</td><td>11,21</td><td>-</td><td>-</td></tr>
<tr><td>28</td><td>40</td><td>1,16</td><td>1,89</td><td>2,31</td><td>2,7</td><td>3,20</td><td>3,92</td><td>4,69</td><td>5,83</td><td>7,13</td><td>8,56</td><td>10,55</td><td>12,77</td><td>-</td><td>-</td></tr>
<tr><td>29</td><td>50</td><td>1,28</td><td>2,09</td><td>2,55</td><td>2,99</td><td>3,59</td><td>4,32</td><td>5,18</td><td>6,44</td><td>7,88</td><td>9,46</td><td>11,66</td><td>14,12</td><td>-</td><td>-</td></tr>
<tr><td>30</td><td>60</td><td>1,39</td><td>2,27</td><td>2,77</td><td>3,24</td><td>3,89</td><td>4,69</td><td>5,62</td><td>6,99</td><td>8,55</td><td>10,3</td><td>12,6</td><td>15,3</td><td>-</td><td>-</td></tr>
<tr><td>31</td><td>80</td><td>1,59</td><td>2,58</td><td>3,15</td><td>3,69</td><td>4,43</td><td>5,35</td><td>6,4</td><td>7,96</td><td>9,73</td><td>11,7</td><td>14,4</td><td>17,4</td><td>21,0</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="7%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="5%"><col width="7%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="13" rowspan="2">Подгибка кромок листов в вальцах</td><td colspan="5">Гибка</td></tr>
<tr><td colspan="5">Карта 22, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина листа</td><td>Толщина листа</td><td colspan="15">Ширина подгибаемой кромки В, мм, до</td></tr>
<tr><td>L, мм,</td><td rowspan="2">h, мм, до</td><td>150</td><td>300</td><td>400</td><td>500</td><td>650</td><td>850</td><td>1100</td><td>1500</td><td>2000</td><td colspan="2">2600</td><td>3500</td><td>4600</td><td>6000</td><td>8000</td></tr>
<tr><td>до</td><td colspan="15">Время на лист Т, чел.-мин.</td></tr>
<tr><td>32</td><td rowspan="11">3000</td><td>4</td><td>0,47</td><td>0,77</td><td>0,94</td><td>1,1</td><td>1,32</td><td>1,59</td><td>1,91</td><td>2,37</td><td>2,9</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>33</td><td>6</td><td>0,57</td><td>0,92</td><td>1,12</td><td>1,32</td><td>1,58</td><td>1,91</td><td>2,29</td><td>2,84</td><td>3,47</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>34</td><td>8</td><td>0,65</td><td>1,05</td><td>1,28</td><td>1,5</td><td>1,8</td><td>2,17</td><td>2,61</td><td>3,24</td><td>3,97</td><td colspan="2">4,76</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>35</td><td>10</td><td>0,71</td><td>1,16</td><td>1,42</td><td>1,66</td><td>2,0</td><td>2,4</td><td>2,9</td><td>3,58</td><td>4,38</td><td colspan="2">5,28</td><td>6,48</td><td>7,85</td><td>-</td><td>-</td></tr>
<tr><td>36</td><td>14</td><td>0,83</td><td>1,35</td><td>1,65</td><td>1,93</td><td>2,32</td><td>2,79</td><td>3,35</td><td>4,16</td><td>5,1</td><td colspan="2">6,12</td><td>7,53</td><td>9,12</td><td>-</td><td>-</td></tr>
<tr><td>37</td><td>20</td><td>0,98</td><td>1,59</td><td>1,94</td><td>2,27</td><td>2,72</td><td>3,29</td><td>3,94</td><td>4,89</td><td>6,0</td><td colspan="2">7,2</td><td>8,86</td><td>10,7</td><td>-</td><td>-</td></tr>
<tr><td>38</td><td>30</td><td>1,17</td><td>1,71</td><td>2,1</td><td>2,4</td><td>2,94</td><td>3,54</td><td>4,24</td><td>5,27</td><td>6,45</td><td colspan="2">7,75</td><td>9,54</td><td>11,56</td><td>-</td><td>-</td></tr>
<tr><td>39</td><td>40</td><td>1,33</td><td>2,17</td><td>2,65</td><td>3,1</td><td>3,72</td><td>4,5</td><td>5,38</td><td>6,68</td><td>8,18</td><td colspan="2">9,83</td><td>12,1</td><td>14,6</td><td>17,6</td><td>-</td></tr>
<tr><td>40</td><td>50</td><td>1,47</td><td>2,39</td><td>2,93</td><td>3,42</td><td>4,11</td><td>4,96</td><td>5,95</td><td>7,39</td><td>9,04</td><td colspan="2">10,9</td><td>13,4</td><td>16,2</td><td>19,5</td><td>-</td></tr>
<tr><td>41</td><td>60</td><td>1,60</td><td>2,6</td><td>3,18</td><td>3,72</td><td>4,47</td><td>5,39</td><td>6,46</td><td>8,03</td><td>9,82</td><td colspan="2">11,8</td><td>14,5</td><td>17,6</td><td>21,2</td><td>25,0</td></tr>
<tr><td>42</td><td>80</td><td>1,82</td><td>2,96</td><td>3,62</td><td>4,23</td><td>5,09</td><td>6,14</td><td>7,35</td><td>9,13</td><td>11,2</td><td colspan="2">13,4</td><td>16,5</td><td>20,0</td><td>23,9</td><td>29,3</td></tr>
<tr><td>43</td><td rowspan="2">5000</td><td>4</td><td>0,56</td><td>0,92</td><td>1,12</td><td>1,31</td><td>1,57</td><td>1,89</td><td>2,27</td><td>2,82</td><td>3,46</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>44</td><td>6</td><td>0,67</td><td>1,09</td><td>1,34</td><td>1,57</td><td>1,88</td><td>2,28</td><td>2,73</td><td>3,39</td><td>4,14</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="7%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Подгибка кромок листов в вальцах</td><td colspan="5">Гибка</td></tr>
<tr><td colspan="5">Карта 22, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина листа</td><td>Толщина листа</td><td colspan="15">Ширина подгибаемой кромки В, мм, до</td></tr>
<tr><td>L, мм,</td><td rowspan="2">h, мм, до</td><td>150</td><td>300</td><td>400</td><td>500</td><td>650</td><td>850</td><td>1100</td><td>1500</td><td>2000</td><td colspan="2">2600</td><td>3500</td><td>4600</td><td>6000</td><td>8000</td></tr>
<tr><td>до</td><td colspan="15">Время на лист Т, чел.-мин.</td></tr>
<tr><td>45</td><td rowspan="9">5000</td><td>8</td><td>0,77</td><td>1,25</td><td>1,53</td><td>1,79</td><td>2,15</td><td>2,59</td><td>3,11</td><td>3,86</td><td>4,72</td><td colspan="2">5,67</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>46</td><td>10</td><td>0,85</td><td>1,38</td><td>1,69</td><td>1,97</td><td>2,37</td><td>2,86</td><td>3,43</td><td>4,26</td><td>5,21</td><td colspan="2">6,27</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>47</td><td>14</td><td>0,99</td><td>1,61</td><td>1,97</td><td>2,29</td><td>2,76</td><td>3,33</td><td>3,99</td><td>4,96</td><td>6,07</td><td colspan="2">7,29</td><td>8,98</td><td>10,8</td><td>-</td><td>-</td></tr>
<tr><td>48</td><td>20</td><td>1,16</td><td>1,89</td><td>2,3</td><td>2,70</td><td>3,24</td><td>3,91</td><td>4,69</td><td>5,82</td><td>7,12</td><td colspan="2">8,56</td><td>10,5</td><td>12,8</td><td>15,4</td><td>-</td></tr>
<tr><td>49</td><td>30</td><td>1,39</td><td>2,26</td><td>2,77</td><td>3,24</td><td>3,89</td><td>4,69</td><td>5,62</td><td>6,98</td><td>8,55</td><td colspan="2">10,2</td><td>12,6</td><td>15,3</td><td>18,4</td><td>22,6</td></tr>
<tr><td>50</td><td>40</td><td>1,59</td><td>2,58</td><td>3,15</td><td>3,69</td><td>4,43</td><td>5,35</td><td>6,40</td><td>7,96</td><td>9,73</td><td colspan="2">11,7</td><td>14,4</td><td>17,4</td><td>21,0</td><td>25,7</td></tr>
<tr><td>51</td><td>50</td><td>1,75</td><td>2,86</td><td>3,49</td><td>4,07</td><td>4,89</td><td>5,91</td><td>7,08</td><td>8,79</td><td>10,8</td><td colspan="2">12,9</td><td>15,9</td><td>19,3</td><td>23,2</td><td>28,4</td></tr>
<tr><td>52</td><td>60</td><td>1,93</td><td>3,09</td><td>3,78</td><td>4,42</td><td>5,31</td><td>6,41</td><td>7,68</td><td>9,55</td><td>11,8</td><td colspan="2">14,0</td><td>17,3</td><td>20,9</td><td>25,2</td><td>30,8</td></tr>
<tr><td>53</td><td>80</td><td>2,17</td><td>3,52</td><td>4,3</td><td>5,04</td><td>6,05</td><td>7,3</td><td>8,75</td><td>10,9</td><td>13,3</td><td colspan="2">15,9</td><td>19,7</td><td>23,8</td><td>28,7</td><td>35,1</td></tr>
<tr><td>54</td><td rowspan="4">8000</td><td>6</td><td>0,81</td><td>1,32</td><td>1,61</td><td>1,88</td><td>2,26</td><td>2,73</td><td>3,27</td><td>4,07</td><td>4,9</td><td colspan="2">5,9</td><td>7,3</td><td>8,8</td><td>10,7</td><td>13,1</td></tr>
<tr><td>55</td><td>8</td><td>0,90</td><td>1,47</td><td>1,79</td><td>2,10</td><td>2,52</td><td>3,04</td><td>3,64</td><td>4,52</td><td>5,5</td><td colspan="2">6,6</td><td>8,1</td><td>9,9</td><td>11,9</td><td>14,6</td></tr>
<tr><td>56</td><td>10</td><td>0,99</td><td>1,62</td><td>1,98</td><td>2,32</td><td>2,78</td><td>3,36</td><td>4,02</td><td>5,0</td><td>6,1</td><td colspan="2">7,3</td><td>9,0</td><td>10,9</td><td>13,2</td><td>16,1</td></tr>
<tr><td>57</td><td>14</td><td>1,16</td><td>1,19</td><td>2,31</td><td>2,69</td><td>3,24</td><td>3,91</td><td>4,68</td><td>5,82</td><td>7,1</td><td colspan="2">8,5</td><td>10,5</td><td>12,7</td><td>15,3</td><td>18,8</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="7%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Подгибка кромок листов в вальцах</td><td colspan="5">Гибка</td></tr>
<tr><td colspan="5">Карта 22, лист 6</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина листа</td><td>Толщина листа</td><td colspan="15">Ширина подгибаемой кромки В, мм, до</td></tr>
<tr><td>L, мм,</td><td rowspan="2">h, мм, до</td><td>150</td><td>300</td><td>400</td><td>500</td><td>650</td><td>850</td><td>1100</td><td>1500</td><td>2000</td><td colspan="2">2600</td><td>3500</td><td>4600</td><td>6000</td><td>8000</td></tr>
<tr><td>до</td><td colspan="15">Время на лист Т, чел.-мин.</td></tr>
<tr><td>58</td><td rowspan="6">8000</td><td>20</td><td>1,36</td><td>2,21</td><td>2,71</td><td>3,16</td><td>3,81</td><td>4,59</td><td>5,5</td><td>6,8</td><td>8,3</td><td colspan="2">10,1</td><td>12,4</td><td>14,9</td><td>18,0</td><td>22,1</td></tr>
<tr><td>59</td><td>30</td><td>1,63</td><td>2,66</td><td>3,25</td><td>3,80</td><td>4,57</td><td>5,52</td><td>6,61</td><td>8,21</td><td>10,0</td><td colspan="2">12,1</td><td>14,9</td><td>17,9</td><td>21,7</td><td>26,5</td></tr>
<tr><td>60</td><td>40</td><td>1,86</td><td>3,19</td><td>3,89</td><td>4,56</td><td>5,47</td><td>6,61</td><td>7,91</td><td>9,83</td><td>12,0</td><td colspan="2">14,4</td><td>17,8</td><td>21,5</td><td>25,9</td><td>31,7</td></tr>
<tr><td>61</td><td>50</td><td>2,06</td><td>3,34</td><td>4,09</td><td>4,78</td><td>5,74</td><td>6,93</td><td>8,3</td><td>10,3</td><td>12,6</td><td colspan="2">15,2</td><td>18,7</td><td>22,6</td><td>27,2</td><td>33,3</td></tr>
<tr><td>62</td><td>60</td><td>2,23</td><td>3,63</td><td>4,44</td><td>5,19</td><td>6,23</td><td>7,52</td><td>9,02</td><td>11,2</td><td>13,7</td><td colspan="2">16,5</td><td>20,3</td><td>24,5</td><td>29,6</td><td>36,2</td></tr>
<tr><td>63</td><td>80</td><td>2,54</td><td>4,13</td><td>5,05</td><td>5,91</td><td>7,1</td><td>8,57</td><td>10,3</td><td>12,7</td><td>15,6</td><td colspan="2">18,7</td><td>23,1</td><td>27,9</td><td>33,7</td><td>41,2</td></tr>
<tr><td>64</td><td rowspan="8">12000</td><td>6</td><td>-</td><td>1,58</td><td>1,93</td><td>2,26</td><td>2,72</td><td>3,28</td><td>3,93</td><td>4,8</td><td>5,9</td><td colspan="2">7,1</td><td>8,8</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>65</td><td>8</td><td>-</td><td>1,68</td><td>2,06</td><td>2,41</td><td>2,89</td><td>3,49</td><td>4,18</td><td>5,2</td><td>6,3</td><td colspan="2">7,6</td><td>9,4</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>66</td><td>10</td><td>-</td><td>1,86</td><td>2,28</td><td>2,66</td><td>3,19</td><td>3,86</td><td>4,62</td><td>5,7</td><td>7,0</td><td colspan="2">8,4</td><td>10,4</td><td>12,6</td><td>15,2</td><td>18,5</td></tr>
<tr><td>67</td><td>14</td><td>-</td><td>-</td><td>2,65</td><td>3,10</td><td>3,72</td><td>4,49</td><td>5,38</td><td>6,6</td><td>8,1</td><td colspan="2">9,8</td><td>12,1</td><td>14,6</td><td>17,6</td><td>21,6</td></tr>
<tr><td>68</td><td>20</td><td>-</td><td>-</td><td>3,05</td><td>3,73</td><td>4,37</td><td>5,27</td><td>6,31</td><td>7,8</td><td>9,6</td><td colspan="2">11,5</td><td>14,2</td><td>17,2</td><td>20,7</td><td>25,3</td></tr>
<tr><td>69</td><td>30</td><td>-</td><td>-</td><td>-</td><td>4,36</td><td>5,24</td><td>6,32</td><td>7,57</td><td>9,4</td><td>11,5</td><td colspan="2">13,8</td><td>17,0</td><td>20,6</td><td>24,8</td><td>30,4</td></tr>
<tr><td>70</td><td>40</td><td>-</td><td>-</td><td>-</td><td>-</td><td>5,97</td><td>7,20</td><td>8,62</td><td>10,1</td><td>13,1</td><td colspan="2">15,7</td><td>18,4</td><td>23,5</td><td>28,3</td><td>34,6</td></tr>
<tr><td>71</td><td>50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>7,96</td><td>9,54</td><td>11,8</td><td>14,5</td><td colspan="2">17,4</td><td>21,4</td><td>25,9</td><td>31,3</td><td>38,2</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="7%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Подгибка кромок листов в вальцах</td><td colspan="5">Гибка</td></tr>
<tr><td colspan="5">Карта 22, лист 7</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина листа</td><td>Толщина листа</td><td colspan="15">Ширина подгибаемой кромки В, мм, до</td></tr>
<tr><td>L, мм,</td><td rowspan="2">h, мм, до</td><td>150</td><td>300</td><td>400</td><td>500</td><td>650</td><td>850</td><td>1100</td><td>1500</td><td>2000</td><td colspan="2">2600</td><td>3500</td><td>4600</td><td>6000</td><td>8000</td></tr>
<tr><td>до</td><td colspan="15">Время на лист Т, чел.-мин.</td></tr>
<tr><td>72</td><td rowspan="2">12000</td><td>60</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>10,3</td><td>12,9</td><td>15,7</td><td colspan="2">18,9</td><td>23,3</td><td>28,2</td><td>33,9</td><td>41,5</td></tr>
<tr><td>73</td><td>80</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>14,4</td><td>17,9</td><td colspan="2">21,5</td><td>26,5</td><td>32,1</td><td>38,6</td><td>47,2</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>


<a id="p101209"></a>Примечания: 1. При измененных условиях подгибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="10%"><col width="8%"><col width="9%"><col width="9%"><col width="6%"><col width="7%"><col width="7%"><col width="10%"><col width="8%"><col width="8%"><col width="9%"><col width="10%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="3">Материал</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="3">Подгибка для вальцовки</td><td colspan="2">Подгибка кромок</td></tr>
<tr><td>нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>цилиндрической обечайки</td><td>конической обечайки</td><td>полуобечайки</td><td>с подкладным листом</td><td>без подкладного листа</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,2</td><td>1,2</td><td>1,0</td><td>0,9</td></tr>
</table>


2. <a id="p101212"></a>Работа выполняется бригадой из двух человек:

                                      0,34    0,45    0,7
<a id="p101213"></a>                        Т = 0,0005 х L     х h     х В   .


<table>
<colgroup><col width="5%"><col width="12%"><col width="16%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12">Подгибка кромок листов перед вальцовкой на прессе Гибка</td></tr>
<tr><td colspan="12">Карта 23, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Подать лист на гибочное приспособление пресса.</td></tr>
<tr><td colspan="12">2. Подвести кромку под пуансон.</td></tr>
<tr><td colspan="12">3. Подогнуть кромку листа по радиусу, передвигая лист (рисунок не в процессе подгибки. приводится)</td></tr>
<tr><td colspan="12">4. Проверить радиус гиба по шаблону.</td></tr>
<tr><td colspan="12">5. Снять лист, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина пуансона</td><td>Ширина листа (длина</td><td>Длина листа</td><td colspan="8">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">l, м, до</td><td>подгибаемой кромки) В,</td><td rowspan="2">L, мм, до</td><td>6</td><td>12</td><td>20</td><td>30</td><td>50</td><td>80</td><td>100</td><td>130</td></tr>
<tr><td>мм, до</td><td colspan="8">Время на лист Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">0,75</td><td rowspan="4">450</td><td>1000</td><td>1,34</td><td>1,82</td><td>2,28</td><td>2,72</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>2000</td><td>1,51</td><td>2,05</td><td>2,57</td><td>3,07</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>5000</td><td>1,77</td><td>2,39</td><td>3,00</td><td>3,59</td><td>4,49</td><td>5,52</td><td>6,09</td><td>6,84</td></tr>
<tr><td>4</td><td>8000</td><td>2,22</td><td>3,01</td><td>3,78</td><td>4,52</td><td>5,65</td><td>6,95</td><td>7,67</td><td>8,61</td></tr>
<tr><td colspan="3"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="16%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="9" rowspan="2">Подгибка кромок листов перед вальцовкой на прессе</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 23, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина пуансона</td><td>Ширина листа (длина</td><td>Длина листа</td><td colspan="8">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">l, м, до</td><td>подгибаемой кромки) В,</td><td rowspan="2">L, мм, до</td><td>6</td><td>12</td><td>20</td><td>30</td><td>50</td><td>80</td><td>100</td><td>130</td></tr>
<tr><td>мм, до</td><td colspan="8">Время на лист Т, чел.-мин.</td></tr>
<tr><td>5</td><td rowspan="12">0,75</td><td>450</td><td>12000</td><td>2,75</td><td>3,72</td><td>4,67</td><td>5,58</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td rowspan="5">750</td><td>1000</td><td>2,29</td><td>3,11</td><td>3,90</td><td>4,66</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>2000</td><td>2,59</td><td>3,51</td><td>4,39</td><td>5,25</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>5000</td><td>3,02</td><td>4,09</td><td>5,13</td><td>6,13</td><td>7,68</td><td>9,44</td><td>10,42</td><td>11,69</td></tr>
<tr><td>9</td><td>8000</td><td>3,80</td><td>5,15</td><td>6,46</td><td>7,72</td><td>9,67</td><td>11,89</td><td>13,12</td><td>14,72</td></tr>
<tr><td>10</td><td>12000</td><td>4,69</td><td>6,36</td><td>7,98</td><td>9,54</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td rowspan="5">1250</td><td>1000</td><td>3,96</td><td>5,37</td><td>6,73</td><td>8,05</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>2000</td><td>4,42</td><td>5,99</td><td>7,51</td><td>8,93</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>5000</td><td>5,16</td><td>6,99</td><td>8,77</td><td>10,49</td><td>13,13</td><td>16,15</td><td>17,81</td><td>19,99</td></tr>
<tr><td>14</td><td>8000</td><td>6,50</td><td>8,81</td><td>11,05</td><td>13,21</td><td>16,53</td><td>20,34</td><td>22,44</td><td>25,17</td></tr>
<tr><td>15</td><td>12000</td><td>8,03</td><td>10,88</td><td>13,64</td><td>16,31</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>1800</td><td>2000</td><td>6,49</td><td>8,79</td><td>11,02</td><td>13,17</td><td>16,49</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="3"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="16%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="9" rowspan="2">Подгибка кромок листов перед вальцовкой на прессе</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 23, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина пуансона</td><td>Ширина листа (длина</td><td>Длина листа</td><td colspan="8">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">l, м, до</td><td>подгибаемой кромки) В,</td><td rowspan="2">L, мм, до</td><td>6</td><td>12</td><td>20</td><td>30</td><td>50</td><td>80</td><td>100</td><td>130</td></tr>
<tr><td>мм, до</td><td colspan="8">Время на лист Т, чел.-мин.</td></tr>
<tr><td>17</td><td rowspan="11">0,75</td><td rowspan="3">1800</td><td>5000</td><td>7,57</td><td>10,26</td><td>12,86</td><td>15,38</td><td>19,25</td><td>23,68</td><td>26,12</td><td>29,31</td></tr>
<tr><td>18</td><td>8000</td><td>9,50</td><td>12,93</td><td>16,21</td><td>19,37</td><td>24,25</td><td>29,83</td><td>32,90</td><td>36,90</td></tr>
<tr><td>19</td><td>12000</td><td>11,78</td><td>15,96</td><td>20,01</td><td>23,92</td><td>29,94</td><td>36,83</td><td>40,63</td><td>45,58</td></tr>
<tr><td>20</td><td rowspan="4">2500</td><td>2000</td><td>9,16</td><td>12,41</td><td>15,56</td><td>18,60</td><td>23,28</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>21</td><td>5000</td><td>10,69</td><td>14,49</td><td>18,17</td><td>21,72</td><td>27,18</td><td>33,44</td><td>36,88</td><td>41,38</td></tr>
<tr><td>22</td><td>8000</td><td>13,47</td><td>18,25</td><td>22,88</td><td>27,35</td><td>34,24</td><td>42,11</td><td>46,46</td><td>52,12</td></tr>
<tr><td>23</td><td>12000</td><td>16,63</td><td>22,54</td><td>28,25</td><td>33,77</td><td>42,27</td><td>51,99</td><td>57,36</td><td>64,36</td></tr>
<tr><td>24</td><td rowspan="4">3500</td><td>2000</td><td>10,96</td><td>14,84</td><td>18,57</td><td>22,21</td><td>27,84</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>25</td><td>5000</td><td>15,22</td><td>20,63</td><td>25,87</td><td>30,92</td><td>38,70</td><td>47,61</td><td>52,51</td><td>58,92</td></tr>
<tr><td>26</td><td>8000</td><td>19,17</td><td>25,98</td><td>32,58</td><td>38,94</td><td>48,74</td><td>59,96</td><td>66,14</td><td>74,20</td></tr>
<tr><td>27</td><td>12000</td><td>23,68</td><td>32,08</td><td>40,22</td><td>48,08</td><td>60,19</td><td>74,03</td><td>81,67</td><td>91,63</td></tr>
<tr><td>28</td><td rowspan="3">1,25</td><td rowspan="3">1250</td><td>1000</td><td>2,89</td><td>3,92</td><td>4,91</td><td>5,87</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>29</td><td>2000</td><td>3,26</td><td>4,42</td><td>5,54</td><td>6,62</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>30</td><td>5000</td><td>3,81</td><td>5,16</td><td>6,46</td><td>7,72</td><td>9,67</td><td>11,89</td><td>13,12</td><td>14,73</td></tr>
<tr><td colspan="3"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="16%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="9" rowspan="2">Подгибка кромок листов перед вальцовкой на прессе</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 23, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина пуансона</td><td>Ширина листа (длина</td><td>Длина листа</td><td colspan="8">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">l, м, до</td><td>подгибаемой кромки) В,</td><td rowspan="2">L, мм, до</td><td>6</td><td>12</td><td>20</td><td>30</td><td>50</td><td>80</td><td>100</td><td>130</td></tr>
<tr><td>мм, до</td><td colspan="8">Время на лист Т, чел.-мин.</td></tr>
<tr><td>31</td><td rowspan="14">1,25</td><td rowspan="2">1250</td><td>8000</td><td>4,79</td><td>6,49</td><td>8,14</td><td>9,73</td><td>12,18</td><td>14,98</td><td>16,53</td><td>18,55</td></tr>
<tr><td>32</td><td>12000</td><td>5,92</td><td>8,02</td><td>10,05</td><td>12,02</td><td>15,04</td><td>18,05</td><td>20,41</td><td>22,90</td></tr>
<tr><td>33</td><td rowspan="4">1800</td><td>2000</td><td>4,78</td><td>6,48</td><td>8,12</td><td>9,71</td><td>12,15</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>34</td><td>5000</td><td>5,58</td><td>7,56</td><td>9,48</td><td>11,33</td><td>14,18</td><td>17,45</td><td>19,25</td><td>21,59</td></tr>
<tr><td>35</td><td>8000</td><td>7,03</td><td>9,52</td><td>11,94</td><td>14,27</td><td>17,86</td><td>21,98</td><td>24,24</td><td>27,20</td></tr>
<tr><td>36</td><td>12000</td><td>8,68</td><td>11,76</td><td>14,74</td><td>17,62</td><td>22,06</td><td>27,13</td><td>29,93</td><td>33,58</td></tr>
<tr><td>37</td><td rowspan="4">2500</td><td>2000</td><td>6,75</td><td>9,14</td><td>11,46</td><td>13,71</td><td>17,15</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>38</td><td>5000</td><td>7,88</td><td>10,68</td><td>13,38</td><td>16,0</td><td>20,03</td><td>24,64</td><td>27,18</td><td>30,49</td></tr>
<tr><td>39</td><td>8000</td><td>9,92</td><td>13,44</td><td>16,86</td><td>20,15</td><td>25,22</td><td>31,03</td><td>34,23</td><td>38,40</td></tr>
<tr><td>40</td><td>12000</td><td>12,25</td><td>16,60</td><td>20,82</td><td>24,88</td><td>31,15</td><td>38,31</td><td>42,26</td><td>47,42</td></tr>
<tr><td>41</td><td rowspan="4">3500</td><td>2000</td><td>9,61</td><td>13,02</td><td>16,32</td><td>19,51</td><td>24,42</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>42</td><td>5000</td><td>11,22</td><td>15,2</td><td>19,06</td><td>22,78</td><td>28,52</td><td>35,08</td><td>38,69</td><td>43,41</td></tr>
<tr><td>43</td><td>8000</td><td>14,12</td><td>19,15</td><td>24,00</td><td>28,69</td><td>35,92</td><td>44,18</td><td>48,73</td><td>54,67</td></tr>
<tr><td>44</td><td>12000</td><td>17,45</td><td>23,64</td><td>29,64</td><td>35,43</td><td>44,35</td><td>54,55</td><td>60,17</td><td>67,51</td></tr>
<tr><td colspan="3"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="16%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="9" rowspan="2">Подгибка кромок листов перед вальцовкой на прессе</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 23, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина пуансона</td><td>Ширина листа (длина</td><td>Длина листа</td><td colspan="8">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">l, м, до</td><td>подгибаемой кромки) В,</td><td rowspan="2">L, мм, до</td><td>6</td><td>12</td><td>20</td><td>30</td><td>50</td><td>80</td><td>100</td><td>130</td></tr>
<tr><td>мм, до</td><td colspan="8">Время на лист Т, чел.-мин.</td></tr>
<tr><td>45</td><td rowspan="4">1,25</td><td rowspan="4">4300</td><td>2000</td><td>11,97</td><td>16,16</td><td>20,26</td><td>24,22</td><td>30,32</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>46</td><td>5000</td><td>13,92</td><td>18,87</td><td>23,65</td><td>28,28</td><td>35,40</td><td>43,54</td><td>48,03</td><td>63,89</td></tr>
<tr><td>47</td><td>8000</td><td>17,54</td><td>23,77</td><td>29,79</td><td>35,62</td><td>44,58</td><td>54,84</td><td>60,49</td><td>67,87</td></tr>
<tr><td>48</td><td>12000</td><td>21,65</td><td>29,35</td><td>36,79</td><td>43,98</td><td>55,05</td><td>67,71</td><td>74,69</td><td>83,80</td></tr>
<tr><td>49</td><td rowspan="9">1,8</td><td rowspan="4">1800</td><td>2000</td><td>3,84</td><td>5,20</td><td>6,52</td><td>7,79</td><td>9,75</td><td>11,99</td><td>13,24</td><td>14,85</td></tr>
<tr><td>50</td><td>5000</td><td>4,48</td><td>6,07</td><td>7,61</td><td>9,10</td><td>11,39</td><td>14,00</td><td>15,45</td><td>17,34</td></tr>
<tr><td>51</td><td>8000</td><td>5,64</td><td>7,65</td><td>9,59</td><td>11,46</td><td>14,34</td><td>17,64</td><td>19,46</td><td>21,84</td></tr>
<tr><td>52</td><td>12000</td><td>6,96</td><td>9,44</td><td>11,84</td><td>14,15</td><td>17,71</td><td>21,78</td><td>24,03</td><td>26,96</td></tr>
<tr><td>53</td><td rowspan="4">2500</td><td>2000</td><td>5,42</td><td>7,34</td><td>9,21</td><td>11,00</td><td>13,77</td><td>16,94</td><td>18,69</td><td>20,97</td></tr>
<tr><td>54</td><td>5000</td><td>6,32</td><td>8,57</td><td>10,75</td><td>12,85</td><td>16,08</td><td>19,78</td><td>21,82</td><td>24,48</td></tr>
<tr><td>55</td><td>8000</td><td>7,96</td><td>10,79</td><td>13,53</td><td>16,18</td><td>20,25</td><td>24,91</td><td>27,48</td><td>30,83</td></tr>
<tr><td>56</td><td>12000</td><td>9,84</td><td>13,33</td><td>16,71</td><td>19,97</td><td>25,0</td><td>30,76</td><td>33,93</td><td>38,07</td></tr>
<tr><td>57</td><td>3500</td><td>2000</td><td>7,71</td><td>10,48</td><td>13,11</td><td>15,66</td><td>19,61</td><td>24,12</td><td>26,61</td><td>29,85</td></tr>
<tr><td colspan="3"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="16%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="9" rowspan="2">Подгибка кромок листов перед вальцовкой на прессе</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 23, лист 6</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина пуансона</td><td>Ширина листа (длина</td><td>Длина листа</td><td colspan="8">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">l, м, до</td><td>подгибаемой кромки) В,</td><td rowspan="2">L, мм, до</td><td>6</td><td>12</td><td>20</td><td>30</td><td>50</td><td>80</td><td>100</td><td>130</td></tr>
<tr><td>мм, до</td><td colspan="8">Время на лист Т, чел.-мин.</td></tr>
<tr><td>58</td><td rowspan="7">1,8</td><td rowspan="4">3500</td><td>5000</td><td>9,01</td><td>12,21</td><td>15,30</td><td>18,29</td><td>22,89</td><td>28,16</td><td>31,06</td><td>34,85</td></tr>
<tr><td>59</td><td>8000</td><td>11,34</td><td>15,37</td><td>19,27</td><td>23,03</td><td>28,83</td><td>35,47</td><td>39,13</td><td>43,89</td></tr>
<tr><td>60</td><td>12000</td><td>14,01</td><td>18,98</td><td>23,79</td><td>28,44</td><td>35,60</td><td>43,79</td><td>48,31</td><td>54,20</td></tr>
<tr><td>61</td><td>2000</td><td>9,57</td><td>12,97</td><td>16,27</td><td>19,45</td><td>24,34</td><td>29,94</td><td>33,03</td><td>37,05</td></tr>
<tr><td>62</td><td rowspan="3">4300</td><td>5000</td><td>11,18</td><td>15,15</td><td>18,99</td><td>22,71</td><td>28,42</td><td>34,96</td><td>38,56</td><td>43,26</td></tr>
<tr><td>63</td><td>8000</td><td>14,08</td><td>19,08</td><td>23,92</td><td>28,59</td><td>35,79</td><td>44,02</td><td>48,56</td><td>54,48</td></tr>
<tr><td>64</td><td>12000</td><td>17,38</td><td>23,56</td><td>29,54</td><td>35,31</td><td>44,19</td><td>54,36</td><td>59,96</td><td>67,28</td></tr>
<tr><td colspan="3"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p101308"></a>Примечания: 1. При измененных условиях подгибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="27%"><col width="11%"><col width="11%"><col width="11%"><col width="14%"><col width="15%"><col width="12%"></colgroup>
<tr><td colspan="5" rowspan="2">Подгибка кромок листов перед вальцовкой на прессе</td><td colspan="2">Гибка</td></tr>
<tr><td colspan="2">Карта 23, лист 7</td></tr>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="3">Материал</td><td colspan="3">Подгибка для вальцовки</td></tr>
<tr><td>времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>цилиндрической обечайки</td><td>конической обечайки</td><td>полуобечайки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,2</td><td>1,2</td></tr>
</table>


2. <a id="p101313"></a>Работа выполняется бригадой из двух человек:

                         1,05    0,17    0,44
              0,00026 х В     х L     х h
<a id="p101314"></a>          Т = -------------------------------       для L <= 5000 мм;
                            0,6
                           l

                         1,05    0,52    0,44
              0,00013 х В     х L     х h
<a id="p101315"></a>          Т = -------------------------------       для L > 5000 мм.
                            0,6
                           l


<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 24, лист 1</td></tr>
<tr><td colspan="17">Содержание работы</td></tr>
<tr><td colspan="17">1. Подать лист к вальцам.</td></tr>
<tr><td colspan="17">2. Заправить кромку листа в вальцы. (рисунок не</td></tr>
<tr><td colspan="17">3. Вальцевать лист в обечайку. приводится)</td></tr>
<tr><td colspan="17">4. Проверить обечайку по диаметру шаблоном.</td></tr>
<tr><td colspan="17">5. Снять обечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>6</td><td>12</td><td>14</td><td>20</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">200</td><td>100</td><td>0,46</td><td>0,58</td><td>0,69</td><td>0,79</td><td>1,05</td><td>1,34</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>300</td><td>0,70</td><td>0,90</td><td>1,07</td><td>1,22</td><td>1,62</td><td>2,06</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>400</td><td>0,79</td><td>1,00</td><td>1,19</td><td>1,36</td><td>1,81</td><td>2,31</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>550</td><td>0,89</td><td>1,14</td><td>1,35</td><td>1,55</td><td>2,05</td><td>2,61</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 24, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>5</td><td rowspan="6">300</td><td>100</td><td>0,62</td><td>0,79</td><td>0,94</td><td>1,07</td><td>1,42</td><td>1,81</td><td>1,99</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>300</td><td>0,95</td><td>1,21</td><td>1,44</td><td>1,65</td><td>2,18</td><td>2,78</td><td>3,05</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>400</td><td>1,06</td><td>1,36</td><td>1,61</td><td>1,84</td><td>2,44</td><td>3,12</td><td>3,42</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>550</td><td>1,20</td><td>1,54</td><td>1,82</td><td>2,09</td><td>2,77</td><td>3,53</td><td>3,87</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>800</td><td>1,39</td><td>1,78</td><td>2,11</td><td>2,41</td><td>3,20</td><td>4,08</td><td>4,48</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>1100</td><td>1,58</td><td>2,01</td><td>2,39</td><td>2,73</td><td>3,62</td><td>4,62</td><td>5,10</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td rowspan="7">400</td><td>100</td><td>0,77</td><td>0,98</td><td>1,16</td><td>1,33</td><td>1,76</td><td>2,24</td><td>2,53</td><td>3,0</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>300</td><td>1,18</td><td>1,50</td><td>1,78</td><td>2,04</td><td>2,70</td><td>3,45</td><td>3,78</td><td>4,6</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>400</td><td>1,31</td><td>1,68</td><td>1,99</td><td>2,28</td><td>3,02</td><td>3,85</td><td>4,23</td><td>5,2</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td>550</td><td>1,49</td><td>1,90</td><td>2,26</td><td>2,58</td><td>3,42</td><td>4,36</td><td>4,79</td><td>5,9</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>800</td><td>1,72</td><td>2,20</td><td>2,61</td><td>2,99</td><td>3,96</td><td>5,10</td><td>5,50</td><td>6,9</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>1100</td><td>1,95</td><td>2,49</td><td>2,96</td><td>3,38</td><td>4,48</td><td>5,70</td><td>6,30</td><td>7,8</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td>1600</td><td>2,26</td><td>2,88</td><td>3,42</td><td>3,91</td><td>5,20</td><td>6,60</td><td>7,30</td><td>8,9</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 24, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>18</td><td rowspan="10">550</td><td>100</td><td>0,97</td><td>1,24</td><td>1,47</td><td>1,7</td><td>2,2</td><td>2,8</td><td>3,1</td><td>3,9</td><td>4,7</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td>300</td><td>1,49</td><td>1,90</td><td>2,85</td><td>2,6</td><td>3,4</td><td>4,4</td><td>4,8</td><td>5,9</td><td>7,2</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>400</td><td>1,66</td><td>2,10</td><td>2,50</td><td>2,9</td><td>3,8</td><td>4,9</td><td>5,3</td><td>6,6</td><td>8,1</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>21</td><td>550</td><td>1,89</td><td>2,40</td><td>2,90</td><td>3,3</td><td>4,3</td><td>5,5</td><td>6,1</td><td>7,5</td><td>9,2</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>22</td><td>800</td><td>2,20</td><td>2,78</td><td>3,30</td><td>3,8</td><td>5,0</td><td>6,4</td><td>7,0</td><td>8,7</td><td>10,6</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>23</td><td>1100</td><td>2,50</td><td>3,15</td><td>3,70</td><td>4,3</td><td>5,7</td><td>7,2</td><td>7,9</td><td>9,8</td><td>12,0</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>24</td><td>1600</td><td>2,90</td><td>3,65</td><td>4,30</td><td>4,9</td><td>6,6</td><td>8,4</td><td>9,2</td><td>11,4</td><td>13,9</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>25</td><td>2300</td><td>3,30</td><td>4,20</td><td>4,90</td><td>5,7</td><td>7,6</td><td>9,6</td><td>10,6</td><td>13,1</td><td>16,0</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>26</td><td>3200</td><td>3,71</td><td>4,80</td><td>5,70</td><td>6,5</td><td>8,6</td><td>10,9</td><td>12,0</td><td>14,9</td><td>18,3</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>27</td><td>3600</td><td>3,90</td><td>5,00</td><td>5,90</td><td>6,8</td><td>9,0</td><td>11,5</td><td>12,6</td><td>15,6</td><td>19,1</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>28</td><td rowspan="4">750</td><td>100</td><td>1,20</td><td>1,56</td><td>1,85</td><td>2,1</td><td>2,8</td><td>3,6</td><td>3,9</td><td>4,9</td><td>5,9</td><td colspan="2">7,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>29</td><td>300</td><td>1,90</td><td>2,40</td><td>2,80</td><td>3,2</td><td>4,3</td><td>5,5</td><td>6,0</td><td>7,5</td><td>9,1</td><td colspan="2">10,9</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>30</td><td>400</td><td>2,10</td><td>2,70</td><td>3,20</td><td>3,6</td><td>4,8</td><td>6,1</td><td>6,7</td><td>8,3</td><td>10,2</td><td colspan="2">12,3</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>31</td><td>550</td><td>2,40</td><td>3,00</td><td>3,60</td><td>4,1</td><td>5,4</td><td>6,9</td><td>7,6</td><td>9,4</td><td>11,6</td><td colspan="2">13,9</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 24, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>32</td><td rowspan="6">750</td><td>800</td><td>2,7</td><td>3,5</td><td>4,2</td><td>4,8</td><td>6,3</td><td>8,0</td><td>8,8</td><td>10,9</td><td>13,4</td><td colspan="2">16,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>33</td><td>1100</td><td>3,1</td><td>3,9</td><td>4,7</td><td>5,4</td><td>7,1</td><td>9,1</td><td>9,9</td><td>12,4</td><td>15,1</td><td colspan="2">18,2</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>34</td><td>1600</td><td>3,6</td><td>4,6</td><td>5,4</td><td>6,2</td><td>8,3</td><td>10,5</td><td>11,6</td><td>14,3</td><td>17,5</td><td colspan="2">21,0</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>35</td><td>2300</td><td>4,4</td><td>5,3</td><td>6,3</td><td>7,2</td><td>9,5</td><td>12,1</td><td>13,3</td><td>16,5</td><td>20,2</td><td colspan="2">24,2</td><td>-</td><td>-</td><td>_</td></tr>
<tr><td>36</td><td>3200</td><td>4,7</td><td>6,0</td><td>7,1</td><td>8,2</td><td>10,8</td><td>13,8</td><td>15,1</td><td>18,8</td><td>22,9</td><td colspan="2">27,6</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>37</td><td>3600</td><td>4,9</td><td>6,3</td><td>7,5</td><td>8,6</td><td>11,3</td><td>14,5</td><td>15,9</td><td>19,6</td><td>24,0</td><td colspan="2">28,9</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>38</td><td rowspan="9">1000</td><td>300</td><td>2,3</td><td>2,9</td><td>3,5</td><td>4,0</td><td>5,3</td><td>6,8</td><td>7,4</td><td>9,2</td><td>11,3</td><td colspan="2">13,6</td><td>15,9</td><td>18,7</td><td>21,2</td></tr>
<tr><td>39</td><td>400</td><td>2,6</td><td>3,3</td><td>3,9</td><td>4,5</td><td>5,9</td><td>7,6</td><td>8,3</td><td>10,3</td><td>12,6</td><td colspan="2">15,2</td><td>17,9</td><td>20,9</td><td>23,7</td></tr>
<tr><td>40</td><td>550</td><td>2,9</td><td>3,7</td><td>4,4</td><td>5,1</td><td>6,7</td><td>8,6</td><td>9,6</td><td>11,7</td><td>14,3</td><td colspan="2">17,2</td><td>20,2</td><td>23,7</td><td>26,8</td></tr>
<tr><td>41</td><td>800</td><td>3,4</td><td>4,3</td><td>5,1</td><td>5,9</td><td>7,8</td><td>9,9</td><td>10,9</td><td>13,5</td><td>16,5</td><td colspan="2">19,9</td><td>23,4</td><td>27,4</td><td>31,1</td></tr>
<tr><td>42</td><td>1100</td><td>3,8</td><td>4,9</td><td>5,8</td><td>6,7</td><td>8,8</td><td>11,3</td><td>12,4</td><td>15,3</td><td>18,7</td><td colspan="2">22,5</td><td>26,5</td><td>31,1</td><td>35,2</td></tr>
<tr><td>43</td><td>1600</td><td>4,4</td><td>5,7</td><td>6,7</td><td>7,7</td><td>10,2</td><td>13,0</td><td>14,3</td><td>17,7</td><td>21,7</td><td colspan="2">26,0</td><td>30,7</td><td>35,9</td><td>40,7</td></tr>
<tr><td>44</td><td>2300</td><td>5,1</td><td>6,5</td><td>7,8</td><td>8,9</td><td>11,8</td><td>15,0</td><td>16,5</td><td>20,4</td><td>24,9</td><td colspan="2">30,0</td><td>35,4</td><td>41,4</td><td>46,9</td></tr>
<tr><td>45</td><td>3200</td><td>5,8</td><td>7,4</td><td>8,8</td><td>10,1</td><td>13,4</td><td>17,1</td><td>18,7</td><td>23,2</td><td>28,4</td><td colspan="2">34,1</td><td>40,2</td><td>47,0</td><td>53,3</td></tr>
<tr><td>46</td><td>3600</td><td>6,1</td><td>7,8</td><td>9,3</td><td>10,6</td><td>14,0</td><td>17,9</td><td>19,6</td><td>24,3</td><td>29,7</td><td colspan="2">35,7</td><td>42,1</td><td>49,3</td><td>55,8</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 24, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>47</td><td rowspan="9">1400</td><td>300</td><td>2,9</td><td>3,8</td><td>4,5</td><td>5,1</td><td>6,8</td><td>8,7</td><td>9,5</td><td>11,8</td><td>14,5</td><td colspan="2">17,4</td><td>20,5</td><td>23,9</td><td>27,2</td></tr>
<tr><td>48</td><td>400</td><td>3,3</td><td>4,2</td><td>5,2</td><td>5,8</td><td>7,6</td><td>9,7</td><td>10,7</td><td>13,2</td><td>16,2</td><td colspan="2">19,4</td><td>22,9</td><td>26,8</td><td>30,4</td></tr>
<tr><td>49</td><td>550</td><td>3,8</td><td>4,8</td><td>5,7</td><td>6,5</td><td>8,6</td><td>11,0</td><td>12,1</td><td>14,9</td><td>18,3</td><td colspan="2">22,0</td><td>25,9</td><td>30,4</td><td>34,4</td></tr>
<tr><td>50</td><td>800</td><td>4,3</td><td>5,6</td><td>6,6</td><td>7,5</td><td>10,0</td><td>12,8</td><td>14,0</td><td>17,3</td><td>21,2</td><td colspan="2">25,5</td><td>30,0</td><td>35,2</td><td>39,8</td></tr>
<tr><td>51</td><td>1100</td><td>4,9</td><td>6,3</td><td>7,5</td><td>8,5</td><td>11,3</td><td>14,4</td><td>15,9</td><td>19,6</td><td>24,0</td><td colspan="2">28,9</td><td>34,0</td><td>39,8</td><td>45,4</td></tr>
<tr><td>52</td><td>1600</td><td>5,7</td><td>7,3</td><td>8,6</td><td>9,9</td><td>13,1</td><td>16,7</td><td>18,3</td><td>22,7</td><td>33,4</td><td colspan="2">39,4</td><td>42,4</td><td>46,1</td><td>52,0</td></tr>
<tr><td>53</td><td>2300</td><td>6,6</td><td>8,4</td><td>9,9</td><td>11,4</td><td>15,1</td><td>19,3</td><td>21,1</td><td>26,2</td><td>32,0</td><td colspan="2">38,5</td><td>45,4</td><td>53,0</td><td>60,0</td></tr>
<tr><td>54</td><td>3200</td><td>7,5</td><td>9,5</td><td>11,3</td><td>12,9</td><td>17,2</td><td>21,9</td><td>24,0</td><td>29,8</td><td>36,4</td><td colspan="2">43,8</td><td>51,0</td><td>60,0</td><td>68,0</td></tr>
<tr><td>55</td><td>3600</td><td>7,8</td><td>9,9</td><td>11,9</td><td>13,6</td><td>18,0</td><td>22,9</td><td>25,2</td><td>31,2</td><td>38,2</td><td colspan="2">45,8</td><td>54,0</td><td>63,0</td><td>71,0</td></tr>
<tr><td>56</td><td rowspan="3">1800</td><td>300</td><td>-</td><td>-</td><td>5,4</td><td>6,2</td><td>8,2</td><td>10,5</td><td>11,5</td><td>14,2</td><td>17,4</td><td colspan="2">20,9</td><td>24,7</td><td>28,9</td><td>32,7</td></tr>
<tr><td>57</td><td>400</td><td>-</td><td>-</td><td>6,1</td><td>6,9</td><td>9,2</td><td>11,7</td><td>12,9</td><td>15,9</td><td>19,5</td><td colspan="2">23,4</td><td>27,6</td><td>32,3</td><td>36,6</td></tr>
<tr><td>58</td><td>550</td><td>-</td><td>-</td><td>6,9</td><td>7,9</td><td>10,4</td><td>13,3</td><td>14,6</td><td>18,0</td><td>22,1</td><td colspan="2">26,5</td><td>31,3</td><td>36,6</td><td>41,5</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка листов в обечайки цилиндрической формы в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 24, лист 6</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="13">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>6</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>59</td><td rowspan="7">1800</td><td>800</td><td>-</td><td>-</td><td>7,9</td><td>9,1</td><td>12,1</td><td>15,4</td><td>16,9</td><td>20,9</td><td>25,6</td><td>30,7</td><td>36,2</td><td>42,4</td><td>49</td></tr>
<tr><td>60</td><td>1100</td><td>-</td><td>-</td><td>9,0</td><td>10,3</td><td>13,6</td><td>17,4</td><td>19,1</td><td>23,6</td><td>28,9</td><td>34,8</td><td>40,9</td><td>47,9</td><td>54</td></tr>
<tr><td>61</td><td>1600</td><td>-</td><td>-</td><td>10,4</td><td>11,9</td><td>15,8</td><td>20,1</td><td>22,1</td><td>27,4</td><td>33,5</td><td>40,2</td><td>47,4</td><td>55,0</td><td>63</td></tr>
<tr><td>62</td><td>2300</td><td>-</td><td>-</td><td>12,0</td><td>13,7</td><td>18,2</td><td>23,2</td><td>25,5</td><td>31,5</td><td>38,6</td><td>46,3</td><td>55,0</td><td>64,0</td><td>72</td></tr>
<tr><td>63</td><td>3200</td><td>-</td><td>-</td><td>13,6</td><td>15,6</td><td>20,7</td><td>26,4</td><td>29,0</td><td>35,9</td><td>43,9</td><td>53,0</td><td>62,0</td><td>73,0</td><td>82</td></tr>
<tr><td>64</td><td>4600</td><td>-</td><td>-</td><td>15,7</td><td>18,0</td><td>23,8</td><td>30,4</td><td>33,4</td><td>41,3</td><td>50,0</td><td>61,0</td><td>72,0</td><td>84,0</td><td>95</td></tr>
<tr><td>65</td><td>6500</td><td>-</td><td>-</td><td>18,0</td><td>20,6</td><td>27,3</td><td>34,8</td><td>38,1</td><td>47,3</td><td>58,0</td><td>69,0</td><td>82,0</td><td>96,0</td><td>108</td></tr>
<tr><td>66</td><td rowspan="7">2400</td><td>800</td><td>-</td><td>-</td><td>9,8</td><td>11,2</td><td>14,9</td><td>19,0</td><td>20,9</td><td>25,9</td><td>31,6</td><td>37,9</td><td>44,8</td><td>52,0</td><td>59</td></tr>
<tr><td>67</td><td>1100</td><td>-</td><td>-</td><td>11,1</td><td>12,7</td><td>16,9</td><td>21,5</td><td>23,6</td><td>29,3</td><td>35,8</td><td>43,0</td><td>50,0</td><td>59,0</td><td>67</td></tr>
<tr><td>68</td><td>1600</td><td>-</td><td>-</td><td>12,9</td><td>14,7</td><td>19,5</td><td>24,9</td><td>27,3</td><td>33,9</td><td>41,4</td><td>49,8</td><td>59,0</td><td>69,0</td><td>78</td></tr>
<tr><td>69</td><td>2300</td><td>-</td><td>-</td><td>14,9</td><td>16,9</td><td>22,5</td><td>28,7</td><td>31,5</td><td>39,0</td><td>47,7</td><td>57,0</td><td>68,0</td><td>79,0</td><td>89</td></tr>
<tr><td>70</td><td>3200</td><td>-</td><td>-</td><td>16,9</td><td>19,3</td><td>25,6</td><td>32,7</td><td>35,8</td><td>44,4</td><td>54,0</td><td>65,0</td><td>77,0</td><td>90,0</td><td>102</td></tr>
<tr><td>71</td><td>4600</td><td>-</td><td>-</td><td>19,5</td><td>22,3</td><td>29,5</td><td>37,6</td><td>41,3</td><td>51,0</td><td>63,0</td><td>75,0</td><td>88,0</td><td>104,0</td><td>117</td></tr>
<tr><td>72</td><td>6500</td><td>-</td><td>-</td><td>22,3</td><td>25,5</td><td>33,8</td><td>43,1</td><td>47,2</td><td>58,0</td><td>72,0</td><td>86,0</td><td>101,0</td><td>119,0</td><td>134</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 24, лист 7</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>73</td><td rowspan="7">3200</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>15,8</td><td>20,9</td><td>26,6</td><td>29,2</td><td>36,2</td><td>44</td><td colspan="2">53</td><td>63</td><td>73</td><td>83</td></tr>
<tr><td>74</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>18,2</td><td>24,2</td><td>30,8</td><td>33,8</td><td>41,9</td><td>51</td><td colspan="2">62</td><td>73</td><td>85</td><td>96</td></tr>
<tr><td>75</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>21,0</td><td>27,9</td><td>35,5</td><td>38,9</td><td>48,3</td><td>59</td><td colspan="2">71</td><td>84</td><td>98</td><td>111</td></tr>
<tr><td>76</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>23,9</td><td>31,7</td><td>40,4</td><td>44,3</td><td>55,0</td><td>67</td><td colspan="2">81</td><td>95</td><td>111</td><td>126</td></tr>
<tr><td>77</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>27,5</td><td>36,5</td><td>46,6</td><td>51,0</td><td>63,0</td><td>77</td><td colspan="2">93</td><td>109</td><td>128</td><td>145</td></tr>
<tr><td>78</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>31,5</td><td>41,8</td><td>53,0</td><td>58,0</td><td>72,0</td><td>88</td><td colspan="2">105</td><td>125</td><td>146</td><td>166</td></tr>
<tr><td>79</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>34,2</td><td>45,3</td><td>58,0</td><td>63,0</td><td>78,0</td><td>96</td><td colspan="2">115</td><td>136</td><td>159</td><td>180</td></tr>
<tr><td>80</td><td rowspan="7">4000</td><td>1100</td><td>-</td><td>-</td><td>16,3</td><td>18,6</td><td>24,6</td><td>31,4</td><td>34,5</td><td>42,7</td><td>52</td><td colspan="2">63</td><td>74</td><td>86</td><td>98</td></tr>
<tr><td>81</td><td>1600</td><td>-</td><td>-</td><td>18,8</td><td>21,5</td><td>28,5</td><td>36,4</td><td>39,9</td><td>49,4</td><td>60</td><td colspan="2">72</td><td>86</td><td>100</td><td>114</td></tr>
<tr><td>82</td><td>2300</td><td>-</td><td>-</td><td>21,7</td><td>24,8</td><td>32,9</td><td>41,9</td><td>46,0</td><td>57,0</td><td>69</td><td colspan="2">84</td><td>98</td><td>115</td><td>131</td></tr>
<tr><td>83</td><td>3200</td><td>-</td><td>-</td><td>24,7</td><td>28,2</td><td>37,4</td><td>47,7</td><td>52,0</td><td>65,0</td><td>79</td><td colspan="2">95</td><td>112</td><td>131</td><td>149</td></tr>
<tr><td>84</td><td>4600</td><td>-</td><td>-</td><td>28,4</td><td>32,5</td><td>43,1</td><td>55,0</td><td>60,0</td><td>74,0</td><td>91</td><td colspan="2">109</td><td>129</td><td>151</td><td>171</td></tr>
<tr><td>85</td><td>6500</td><td>-</td><td>-</td><td>32,5</td><td>37,2</td><td>49,3</td><td>63,0</td><td>69,0</td><td>85,0</td><td>104</td><td colspan="2">125</td><td>148</td><td>173</td><td>196</td></tr>
<tr><td>86</td><td>8000</td><td>-</td><td>-</td><td>35,2</td><td>40,3</td><td>53,0</td><td>68,0</td><td>75,0</td><td>92,0</td><td>113</td><td colspan="2">136</td><td>160</td><td>188</td><td>213</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="5%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 24, лист 8</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>87</td><td rowspan="7">5000</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>21,1</td><td>28,0</td><td>35,7</td><td>39</td><td>48</td><td>59</td><td colspan="2">71</td><td>84</td><td>98</td><td>112</td></tr>
<tr><td>88</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>25,4</td><td>33,6</td><td>42,9</td><td>47</td><td>58</td><td>71</td><td colspan="2">86</td><td>101</td><td>118</td><td>134</td></tr>
<tr><td>89</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>29,2</td><td>38,8</td><td>49,4</td><td>54</td><td>67</td><td>82</td><td colspan="2">99</td><td>116</td><td>136</td><td>154</td></tr>
<tr><td>90</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>33,3</td><td>44,1</td><td>56,0</td><td>62</td><td>76</td><td>93</td><td colspan="2">112</td><td>132</td><td>155</td><td>175</td></tr>
<tr><td>91</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>38,3</td><td>50,0</td><td>65,0</td><td>71</td><td>88</td><td>108</td><td colspan="2">129</td><td>152</td><td>178</td><td>202</td></tr>
<tr><td>92</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>43,8</td><td>58,0</td><td>74,0</td><td>81</td><td>100</td><td>123</td><td colspan="2">148</td><td>174</td><td>204</td><td>231</td></tr>
<tr><td>93</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>47,5</td><td>63,0</td><td>80,0</td><td>88</td><td>109</td><td>133</td><td colspan="2">160</td><td>189</td><td>221</td><td>251</td></tr>
<tr><td>94</td><td rowspan="7">6000</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>25,1</td><td>33,3</td><td>42,4</td><td>46</td><td>58</td><td>70</td><td colspan="2">85</td><td>100</td><td>117</td><td>132</td></tr>
<tr><td>95</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>29,0</td><td>38,5</td><td>49,1</td><td>54</td><td>67</td><td>82</td><td colspan="2">98</td><td>116</td><td>135</td><td>153</td></tr>
<tr><td>96</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>33,5</td><td>44,5</td><td>57,0</td><td>62</td><td>77</td><td>94</td><td colspan="2">113</td><td>133</td><td>156</td><td>176</td></tr>
<tr><td>97</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>38,1</td><td>50,0</td><td>64,0</td><td>71</td><td>87</td><td>107</td><td colspan="2">128</td><td>151</td><td>177</td><td>201</td></tr>
<tr><td>98</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>43,68</td><td>58,0</td><td>74,0</td><td>81</td><td>100</td><td>123</td><td colspan="2">148</td><td>175</td><td>204</td><td>231</td></tr>
<tr><td>99</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>50,0</td><td>66,0</td><td>85,0</td><td>93</td><td>115</td><td>141</td><td colspan="2">169</td><td>200</td><td>234</td><td>265</td></tr>
<tr><td>100</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>54,0</td><td>72,0</td><td>92,0</td><td>100</td><td>125</td><td>153</td><td colspan="2">184</td><td>217</td><td>253</td><td>287</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 24, лист 9</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>6</td><td>12</td><td>14</td><td>20</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>101</td><td rowspan="7">7000</td><td>1100</td><td>_</td><td>_</td><td>_</td><td>28,1</td><td>37,3</td><td>47</td><td>52</td><td>64</td><td>79</td><td colspan="2">95</td><td>112</td><td>131</td><td>148</td></tr>
<tr><td>102</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>32,5</td><td>43,2</td><td>55</td><td>60</td><td>75</td><td>91</td><td colspan="2">110</td><td>129</td><td>152</td><td>172</td></tr>
<tr><td>103</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>37,5</td><td>49,7</td><td>63</td><td>69</td><td>86</td><td>105</td><td colspan="2">126</td><td>149</td><td>175</td><td>198</td></tr>
<tr><td>104</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>42,7</td><td>57,0</td><td>72</td><td>79</td><td>98</td><td>120</td><td colspan="2">144</td><td>170</td><td>199</td><td>225</td></tr>
<tr><td>105</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>49,1</td><td>65,0</td><td>83</td><td>91</td><td>113</td><td>138</td><td colspan="2">166</td><td>196</td><td>229</td><td>259</td></tr>
<tr><td>106</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>56,0</td><td>75,0</td><td>95</td><td>104</td><td>129</td><td>158</td><td colspan="2">190</td><td>224</td><td>262</td><td>297</td></tr>
<tr><td>107</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>61,0</td><td>81,0</td><td>103</td><td>113</td><td>140</td><td>171</td><td colspan="2">205</td><td>243</td><td>284</td><td>322</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
</table>


<a id="p101465"></a>Примечания: 1. Нормативы времени рассчитаны на гибку обечаек с предварительно подогнутыми кромками.
2. <a id="p101466"></a>Время на подгибку кромок брать по карте 22 или 23.
3. <a id="p101467"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="12%"><col width="7%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 24, лист 10</td></tr>
<tr><td rowspan="2">Факторы, влияющие на изменение норм времени</td><td colspan="3">Материал</td><td colspan="4">Кол-во одновременно сгибаемых обечаек</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="2">Гибка листов в обечайки</td><td colspan="3">Вальцовка обечаек</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>1</td><td>2</td><td>3</td><td>4</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>цилиндрической формы</td><td>эллиптической формы</td><td>из одного листа</td><td>из двух сварных листов</td><td>из трех сварных листов</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,7</td><td>0,55</td><td>0,45</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,3</td><td>1,0</td><td>1,15</td><td>1,3</td></tr>
</table>


4. <a id="p101472"></a>Работа выполняется бригадой из двух человек:

                                   0,74    0,39    0,6
<a id="p101473"></a>                   Т = 0,000996 х Д     х L     х h   .


<table>
<colgroup><col width="4%"><col width="9%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах и сборка продольного стыка</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 25, лист 1</td></tr>
<tr><td colspan="16">Содержание работы</td></tr>
<tr><td colspan="16">1. Подать лист к вальцам. 4. Подогнать продольный стык обечайки</td></tr>
<tr><td colspan="16">2. Заправить кромку листа в вальцы. с помощью приспособлений.</td></tr>
<tr><td colspan="16">3. Вальцевать лист в обечайку с проверкой диаметра 5. Прихватить стык электросваркой.</td></tr>
<tr><td colspan="16">по шаблону. 6. Снять сборочные приспособления. 7. Снять обечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="13">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">200</td><td>100</td><td>1,02</td><td>1,26</td><td>1,47</td><td>1,66</td><td>2,12</td><td>2,64</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>300</td><td>1,50</td><td>1,86</td><td>2,16</td><td>2,43</td><td>3,12</td><td>3,87</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>400</td><td>1,66</td><td>2,05</td><td>2,39</td><td>2,69</td><td>3,45</td><td>4,28</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>550</td><td>1,85</td><td>2,30</td><td>2,67</td><td>3,01</td><td>3,86</td><td>4,79</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td rowspan="4">300</td><td>100</td><td>1,33</td><td>1,65</td><td>1,92</td><td>2,16</td><td>2,78</td><td>3,44</td><td>3,74</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>300</td><td>1,96</td><td>2,64</td><td>2,83</td><td>3,18</td><td>4,08</td><td>5,06</td><td>5,49</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>400</td><td>2,16</td><td>2,68</td><td>3,13</td><td>3,52</td><td>4,51</td><td>5,60</td><td>6,07</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>550</td><td>2,42</td><td>3,00</td><td>3,49</td><td>3,93</td><td>5,05</td><td>6,26</td><td>6,79</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="7%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах и сборка продольного стыка</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 25, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="13">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>9</td><td rowspan="2">300</td><td>800</td><td>2,76</td><td>3,42</td><td>3,98</td><td>4,48</td><td>5,75</td><td>7,13</td><td>7,74</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>1100</td><td>3,08</td><td>3,82</td><td>4,45</td><td>5,01</td><td>6,43</td><td>7,97</td><td>8,65</td><td>10,45</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td rowspan="7">400</td><td>100</td><td>1,61</td><td>1,99</td><td>2,33</td><td>2,62</td><td>3,36</td><td>4,17</td><td>4,52</td><td>5,46</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>300</td><td>2,37</td><td>2,93</td><td>3,42</td><td>3,85</td><td>4,93</td><td>6,12</td><td>6,64</td><td>8,02</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>400</td><td>2,62</td><td>3,25</td><td>3,78</td><td>4,25</td><td>5,46</td><td>6,77</td><td>7,34</td><td>8,87</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td>550</td><td>2,93</td><td>3,63</td><td>4,23</td><td>4,76</td><td>6,10</td><td>7,56</td><td>8,21</td><td>9,92</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>800</td><td>3,34</td><td>4,14</td><td>4,82</td><td>5,42</td><td>6,96</td><td>8,62</td><td>9,36</td><td>11,31</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>1100</td><td>3,73</td><td>4,62</td><td>5,39</td><td>6,06</td><td>7,78</td><td>9,64</td><td>10,50</td><td>12,60</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td>1600</td><td>4,25</td><td>5,27</td><td>6,06</td><td>6,91</td><td>8,87</td><td>10,90</td><td>11,90</td><td>14,40</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td rowspan="4">550</td><td>100</td><td>1,99</td><td>2,46</td><td>2,86</td><td>3,22</td><td>4,13</td><td>5,12</td><td>5,56</td><td>6,72</td><td>8,03</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td>300</td><td>2,92</td><td>3,62</td><td>4,22</td><td>4,75</td><td>6,09</td><td>7,55</td><td>8,19</td><td>9,90</td><td>11,80</td><td>_</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>400</td><td>3,23</td><td>4,01</td><td>4,66</td><td>5,25</td><td>6,73</td><td>8,35</td><td>9,06</td><td>10,90</td><td>13,10</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>21</td><td>550</td><td>3,61</td><td>4,48</td><td>5,22</td><td>5,88</td><td>7,54</td><td>9,35</td><td>10,10</td><td>12,20</td><td>14,60</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="7%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах и сборка продольного стыка</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 25, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="13">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>22</td><td rowspan="6">550</td><td>800</td><td>4,12</td><td>5,10</td><td>5,95</td><td>6,65</td><td>8,58</td><td>10,6</td><td>11,5</td><td>13,9</td><td>16,7</td><td>-</td><td>-</td><td>-</td><td>_</td></tr>
<tr><td>23</td><td>1100</td><td>4,60</td><td>5,71</td><td>6,65</td><td>7,48</td><td>9,59</td><td>11,9</td><td>12,9</td><td>15,6</td><td>18,6</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>24</td><td>1600</td><td>5,25</td><td>6,51</td><td>7,58</td><td>8,53</td><td>10,90</td><td>13,6</td><td>14,7</td><td>17,8</td><td>21,3</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>25</td><td>2300</td><td>5,96</td><td>7,39</td><td>8,60</td><td>9,68</td><td>12,40</td><td>15,4</td><td>17,2</td><td>20,2</td><td>24,1</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>26</td><td>3200</td><td>8,69</td><td>8,29</td><td>9,66</td><td>10,90</td><td>13,90</td><td>17,3</td><td>18,8</td><td>22,7</td><td>27,1</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>27</td><td>3600</td><td>7,00</td><td>8,68</td><td>10,10</td><td>11,40</td><td>14,60</td><td>18,1</td><td>19,6</td><td>23,7</td><td>28,3</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>28</td><td rowspan="9">750</td><td>100</td><td>2,44</td><td>3,02</td><td>3,52</td><td>3,96</td><td>5,09</td><td>6,3</td><td>8,2</td><td>9,8</td><td>11,6</td><td>14,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>29</td><td>300</td><td>3,58</td><td>4,44</td><td>5,18</td><td>5,82</td><td>7,47</td><td>9,2</td><td>10,0</td><td>12,1</td><td>14,5</td><td>17,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>30</td><td>400</td><td>3,96</td><td>4,91</td><td>5,72</td><td>6,44</td><td>8,26</td><td>10,2</td><td>11,1</td><td>13,4</td><td>16,1</td><td>18,9</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>31</td><td>550</td><td>4,43</td><td>5,49</td><td>6,40</td><td>7,20</td><td>9,24</td><td>11,5</td><td>12,4</td><td>15,0</td><td>17,9</td><td>21,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>32</td><td>800</td><td>5,05</td><td>6,26</td><td>7,30</td><td>8,21</td><td>10,50</td><td>13,1</td><td>14,2</td><td>17,1</td><td>20,5</td><td>24,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>33</td><td>1100</td><td>5,65</td><td>7,00</td><td>8,16</td><td>9,18</td><td>11,80</td><td>14,6</td><td>15,8</td><td>19,1</td><td>22,9</td><td>26,8</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>34</td><td>1600</td><td>6,44</td><td>7,98</td><td>9,30</td><td>10,50</td><td>13,40</td><td>16,6</td><td>18,1</td><td>21,8</td><td>26,1</td><td>30,7</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>35</td><td>2300</td><td>7,31</td><td>10,00</td><td>10,60</td><td>11,90</td><td>15,20</td><td>18,9</td><td>20,5</td><td>24,8</td><td>29,6</td><td>34,8</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>36</td><td>3200</td><td>8,21</td><td>10,20</td><td>11,80</td><td>13,30</td><td>17,11</td><td>21,2</td><td>23,0</td><td>27,8</td><td>33,2</td><td>39,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="7%"><col width="6%"><col width="6%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах и сборка продольного стыка</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 25, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="13">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>37</td><td>750</td><td>3600</td><td>8,55</td><td>10,60</td><td>12,30</td><td>13,90</td><td>17,80</td><td>22,1</td><td>23,9</td><td>28,9</td><td>34,6</td><td>40,7</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>38</td><td rowspan="9">1000</td><td>300</td><td>-</td><td>5,37</td><td>6,26</td><td>7,04</td><td>9,04</td><td>11,2</td><td>12,1</td><td>14,7</td><td>17,6</td><td>20,6</td><td>23,9</td><td>27,4</td><td>30,6</td></tr>
<tr><td>39</td><td>400</td><td>-</td><td>5,94</td><td>6,92</td><td>7,79</td><td>9,99</td><td>12,4</td><td>13,4</td><td>16,2</td><td>19,4</td><td>22,8</td><td>26,4</td><td>30,3</td><td>33,9</td></tr>
<tr><td>40</td><td>550</td><td>-</td><td>6,64</td><td>7,74</td><td>8,71</td><td>11,2</td><td>13,8</td><td>15,0</td><td>18,2</td><td>21,7</td><td>25,5</td><td>29,5</td><td>33,9</td><td>37,9</td></tr>
<tr><td>41</td><td>800</td><td>-</td><td>7,57</td><td>8,82</td><td>9,93</td><td>12,7</td><td>15,8</td><td>17,1</td><td>20,1</td><td>24,7</td><td>29,1</td><td>33,6</td><td>38,7</td><td>43,2</td></tr>
<tr><td>42</td><td>1100</td><td>-</td><td>8,47</td><td>9,86</td><td>11,1</td><td>14,2</td><td>17,6</td><td>19,1</td><td>23,1</td><td>27,7</td><td>32,5</td><td>37,6</td><td>43,2</td><td>48,2</td></tr>
<tr><td>43</td><td>1600</td><td>-</td><td>9,65</td><td>11,20</td><td>12,7</td><td>16,2</td><td>20,2</td><td>21,8</td><td>26,4</td><td>31,5</td><td>37,1</td><td>42,9</td><td>49,3</td><td>55,0</td></tr>
<tr><td>44</td><td>2300</td><td>-</td><td>10,90</td><td>12,80</td><td>14,4</td><td>18,4</td><td>22,8</td><td>24,8</td><td>29,9</td><td>35,8</td><td>42,1</td><td>48,7</td><td>55,9</td><td>62,9</td></tr>
<tr><td>45</td><td>3200</td><td>-</td><td>12,30</td><td>14,30</td><td>16,1</td><td>20,7</td><td>25,6</td><td>27,8</td><td>33,6</td><td>40,2</td><td>47,3</td><td>54,6</td><td>62,8</td><td>70,1</td></tr>
<tr><td>46</td><td>3600</td><td>-</td><td>12,80</td><td>14,90</td><td>16,8</td><td>21,6</td><td>26,7</td><td>29,9</td><td>35,0</td><td>41,9</td><td>49,2</td><td>56,9</td><td>65,4</td><td>73,1</td></tr>
<tr><td>47</td><td rowspan="4">1400</td><td>300</td><td>-</td><td>6,71</td><td>7,81</td><td>8,79</td><td>11,3</td><td>13,9</td><td>15,2</td><td>18,3</td><td>21,9</td><td>25,8</td><td>29,8</td><td>34,2</td><td>38,2</td></tr>
<tr><td>48</td><td>400</td><td>-</td><td>7,42</td><td>8,64</td><td>9,72</td><td>12,5</td><td>15,5</td><td>16,8</td><td>20,3</td><td>24,2</td><td>28,5</td><td>32,9</td><td>37,9</td><td>42,3</td></tr>
<tr><td>49</td><td>550</td><td>-</td><td>8,29</td><td>9,66</td><td>10,9</td><td>13,9</td><td>17,3</td><td>18,8</td><td>22,7</td><td>27,1</td><td>31,9</td><td>36,8</td><td>42,3</td><td>47,3</td></tr>
<tr><td>50</td><td>800</td><td>-</td><td>9,46</td><td>11,00</td><td>12,4</td><td>15,9</td><td>19,7</td><td>21,4</td><td>25,8</td><td>36,3</td><td>42,1</td><td>48,3</td><td>53,9</td><td>57,4</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="7%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="6%"><col width="3%"><col width="4%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="14" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах и сборка продольного стыка</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 25, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td colspan="2">50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>51</td><td rowspan="5">1400</td><td>1100</td><td>-</td><td>10,60</td><td>12,30</td><td>13,8</td><td>17,8</td><td>22,0</td><td>23,9</td><td>28,9</td><td>34,5</td><td>40,6</td><td colspan="2">46,90</td><td>54,10</td><td>60,20</td></tr>
<tr><td>52</td><td>1600</td><td>-</td><td>12,10</td><td>14,00</td><td>15,8</td><td>20,3</td><td>25,1</td><td>27,3</td><td>32,9</td><td>39,4</td><td>46,3</td><td colspan="2">53,50</td><td>61,50</td><td>68,70</td></tr>
<tr><td>53</td><td>2300</td><td>-</td><td>13,70</td><td>15,90</td><td>17,90</td><td>23,00</td><td>28,50</td><td>30,90</td><td>37,40</td><td>44,70</td><td>52,60</td><td colspan="2">60,80</td><td>69,90</td><td>77,90</td></tr>
<tr><td>54</td><td>3200</td><td>-</td><td>15,40</td><td>17,90</td><td>20,80</td><td>25,80</td><td>32,00</td><td>34,70</td><td>41,90</td><td>50,20</td><td>59,00</td><td colspan="2">68,10</td><td>78,40</td><td>87,50</td></tr>
<tr><td>55</td><td>3600</td><td>-</td><td>16,00</td><td>18,60</td><td>20,90</td><td>26,90</td><td>33,40</td><td>36,20</td><td>43,80</td><td>52,30</td><td>61,50</td><td colspan="2">71,10</td><td>81,70</td><td>91,20</td></tr>
<tr><td>56</td><td rowspan="10">1800</td><td>300</td><td>-</td><td>-</td><td>9,20</td><td>10,39</td><td>13,32</td><td>16,51</td><td>17,91</td><td>21,64</td><td>25,87</td><td>30,42</td><td colspan="2">35,18</td><td>40,43</td><td>45,13</td></tr>
<tr><td>57</td><td>400</td><td>-</td><td>-</td><td>10,20</td><td>11,48</td><td>14,73</td><td>18,26</td><td>19,81</td><td>23,94</td><td>28,62</td><td>33,64</td><td colspan="2">38,91</td><td>44,71</td><td>49,92</td></tr>
<tr><td>58</td><td>550</td><td>-</td><td>-</td><td>11,41</td><td>12,83</td><td>16,47</td><td>20,42</td><td>22,15</td><td>26,76</td><td>31,98</td><td>37,61</td><td colspan="2">43,50</td><td>49,99</td><td>55,60</td></tr>
<tr><td>59</td><td>800</td><td>-</td><td>-</td><td>13,00</td><td>14,63</td><td>18,77</td><td>23,28</td><td>25,25</td><td>30,51</td><td>36,46</td><td>42,88</td><td colspan="2">49,59</td><td>56,99</td><td>63,62</td></tr>
<tr><td>60</td><td>1100</td><td>-</td><td>-</td><td>14,54</td><td>16,36</td><td>20,99</td><td>26,02</td><td>28,23</td><td>34,11</td><td>40,76</td><td>47,93</td><td colspan="2">55,44</td><td>63,70</td><td>71,12</td></tr>
<tr><td>61</td><td>1600</td><td>-</td><td>-</td><td>16,57</td><td>18,65</td><td>23,93</td><td>29,67</td><td>32,19</td><td>38,89</td><td>46,49</td><td>54,65</td><td colspan="2">63,21</td><td>72,63</td><td>81,08</td></tr>
<tr><td>62</td><td>2300</td><td>-</td><td>-</td><td>18,89</td><td>21,25</td><td>27,26</td><td>33,80</td><td>36,68</td><td>44,31</td><td>52,97</td><td>62,27</td><td colspan="2">72,02</td><td>82,76</td><td>92,39</td></tr>
<tr><td>63</td><td>3200</td><td>-</td><td>-</td><td>21,12</td><td>23,77</td><td>30,50</td><td>37,81</td><td>41,02</td><td>49,56</td><td>59,623</td><td>69,66</td><td colspan="2">80,56</td><td>92,57</td><td>103,34</td></tr>
<tr><td>64</td><td>4600</td><td>-</td><td>-</td><td>23,99</td><td>26,99</td><td>34,63</td><td>42,94</td><td>46,58</td><td>56,28</td><td>67,26</td><td>75,09</td><td colspan="2">91,47</td><td>105,12</td><td>117,35</td></tr>
<tr><td>65</td><td>6500</td><td>-</td><td>-</td><td>27,07</td><td>30,46</td><td>39,08</td><td>48,46</td><td>52,57</td><td>63,52</td><td>75,91</td><td>89,27</td><td colspan="2">103,24</td><td>118,64</td><td>132,44</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="7%"><col width="4%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="3%"><col width="4%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="14" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах и сборка продольного стыка</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 25, лист 6</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td colspan="2">50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>66</td><td rowspan="7">2400</td><td>800</td><td>-</td><td>-</td><td>15,72</td><td>17,69</td><td>22,70</td><td>28,14</td><td>30,53</td><td>36,89</td><td>44,10</td><td>51,84</td><td colspan="2">59,96</td><td>68,90</td><td>76,92</td></tr>
<tr><td>67</td><td>1100</td><td>-</td><td>-</td><td>17,58</td><td>19,78</td><td>25,37</td><td>31,46</td><td>34,13</td><td>41,24</td><td>49,30</td><td>57,90</td><td colspan="2">67,03</td><td>77,02</td><td>85,98</td></tr>
<tr><td>68</td><td>1600</td><td>-</td><td>-</td><td>20,04</td><td>22,50</td><td>28,90</td><td>35,87</td><td>38,90</td><td>47,02</td><td>56,20</td><td>66,10</td><td colspan="2">76,40</td><td>87,80</td><td>98,00</td></tr>
<tr><td>69</td><td>2300</td><td>-</td><td>-</td><td>22,80</td><td>25,70</td><td>32,90</td><td>40,90</td><td>44,30</td><td>53,60</td><td>64,00</td><td>75,30</td><td colspan="2">87,10</td><td>100,10</td><td>111,70</td></tr>
<tr><td>70</td><td>3200</td><td>-</td><td>-</td><td>25,50</td><td>28,70</td><td>36,90</td><td>45,70</td><td>49,60</td><td>59,90</td><td>71,60</td><td>84,20</td><td colspan="2">97,40</td><td>111,90</td><td>124,90</td></tr>
<tr><td>71</td><td>4600</td><td>-</td><td>-</td><td>29,00</td><td>32,60</td><td>41,90</td><td>51,90</td><td>53,40</td><td>64,50</td><td>81,30</td><td>95,60</td><td colspan="2">110,60</td><td>127,10</td><td>141,90</td></tr>
<tr><td>72</td><td>6500</td><td>-</td><td>-</td><td>32,70</td><td>36,80</td><td>47,20</td><td>58,60</td><td>63,60</td><td>76,80</td><td>91,80</td><td>107,90</td><td colspan="2">124,80</td><td>143,40</td><td>160,10</td></tr>
<tr><td>73</td><td rowspan="7">3200</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>23,90</td><td>30,70</td><td>38,00</td><td>41,30</td><td>49,90</td><td>59,60</td><td>70,10</td><td colspan="2">81,00</td><td>93,10</td><td>103,90</td></tr>
<tr><td>74</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>27,30</td><td>34,90</td><td>43,40</td><td>47,10</td><td>56,80</td><td>67,90</td><td>79,90</td><td colspan="2">92,40</td><td>106,20</td><td>118,00</td></tr>
<tr><td>75</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>31,10</td><td>39,80</td><td>49,40</td><td>53,60</td><td>65,80</td><td>77,40</td><td>91,00</td><td colspan="2">105,30</td><td>121,00</td><td>135,10</td></tr>
<tr><td>76</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>34,70</td><td>44,60</td><td>55,30</td><td>59,90</td><td>72,40</td><td>86,60</td><td>101,80</td><td colspan="2">117,80</td><td>135,30</td><td>151,10</td></tr>
<tr><td>77</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>39,40</td><td>50,60</td><td>62,80</td><td>68,10</td><td>82,30</td><td>98,30</td><td>115,60</td><td colspan="2">133,70</td><td>153,70</td><td>171,50</td></tr>
<tr><td>78</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>44,50</td><td>57,10</td><td>70,80</td><td>76,80</td><td>92,80</td><td>111,00</td><td>130,50</td><td colspan="2">150,90</td><td>173,40</td><td>193,60</td></tr>
<tr><td>79</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>47,90</td><td>61,40</td><td>76,10</td><td>82,60</td><td>99,80</td><td>119,40</td><td>140,30</td><td colspan="2">162,30</td><td>186,50</td><td>208,20</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="7%"><col width="4%"><col width="4%"><col width="3%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="4%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="14" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах и сборка продольного стыка</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 25, лист 7</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td colspan="2">50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>80</td><td rowspan="7">4000</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>27,70</td><td>35,50</td><td>44,10</td><td>47,80</td><td>57,80</td><td>69,10</td><td>81,20</td><td colspan="2">93,90</td><td>107,90</td><td>120,50</td></tr>
<tr><td>81</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>31,60</td><td>40,50</td><td>50,20</td><td>54,50</td><td>65,90</td><td>78,70</td><td>92,60</td><td colspan="2">107,10</td><td>123,00</td><td>137,30</td></tr>
<tr><td>82</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>35,90</td><td>46,20</td><td>57,30</td><td>62,10</td><td>75,00</td><td>89,70</td><td>105,50</td><td colspan="2">121,90</td><td>140,20</td><td>156,50</td></tr>
<tr><td>83</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>40,30</td><td>51,60</td><td>64,00</td><td>69,50</td><td>83,90</td><td>100,40</td><td>117,90</td><td colspan="2">136,40</td><td>156,80</td><td>175,00</td></tr>
<tr><td>84</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>45,70</td><td>58,60</td><td>72,70</td><td>78,90</td><td>95,30</td><td>114,00</td><td>134,00</td><td colspan="2">154,90</td><td>178,00</td><td>198,60</td></tr>
<tr><td>85</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>51,60</td><td>66,20</td><td>82,10</td><td>89,10</td><td>107,60</td><td>128,60</td><td>151,20</td><td colspan="2">174,90</td><td>200,90</td><td>224,30</td></tr>
<tr><td>86</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>55,50</td><td>71,20</td><td>88,30</td><td>95,80</td><td>115,70</td><td>138,30</td><td>162,60</td><td colspan="2">188,10</td><td>216,10</td><td>241,20</td></tr>
<tr><td>87</td><td rowspan="7">5000</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>-</td><td>41,20</td><td>51,10</td><td>55,40</td><td>66,90</td><td>80,00</td><td>94,10</td><td colspan="2">108,80</td><td>125,00</td><td>139,60</td></tr>
<tr><td>88</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>-</td><td>47,00</td><td>58,20</td><td>63,20</td><td>76,30</td><td>96,50</td><td>107,30</td><td colspan="2">124,00</td><td>142,50</td><td>159,20</td></tr>
<tr><td>89</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>-</td><td>53,50</td><td>66,30</td><td>72,00</td><td>87,00</td><td>104,00</td><td>122,20</td><td colspan="2">141,30</td><td>162,40</td><td>181,30</td></tr>
<tr><td>90</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>-</td><td>59,80</td><td>74,20</td><td>80,50</td><td>97,30</td><td>116,30</td><td>136,70</td><td colspan="2">158,10</td><td>181,70</td><td>202,80</td></tr>
<tr><td>91</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>-</td><td>67,90</td><td>84,30</td><td>91,40</td><td>110,40</td><td>132,00</td><td>155,20</td><td colspan="2">179,50</td><td>206,30</td><td>230,30</td></tr>
<tr><td>92</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>-</td><td>76,70</td><td>96,10</td><td>103,20</td><td>124,70</td><td>149,00</td><td>175,20</td><td colspan="2">202,60</td><td>232,80</td><td>259,90</td></tr>
<tr><td>93</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>-</td><td>82,50</td><td>102,30</td><td>110,90</td><td>134,10</td><td>160,20</td><td>188,40</td><td colspan="2">217,90</td><td>250,40</td><td>279,50</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="4%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="14" rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах и сборка продольного стыка</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 25, лист 8</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="14">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td colspan="2">50</td><td>65</td><td>80</td></tr>
<tr><td>до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>94</td><td rowspan="7">6000</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>-</td><td>46,40</td><td>57,60</td><td>62,50</td><td>75,50</td><td>90,20</td><td>106,10</td><td colspan="2">122,70</td><td>141,00</td><td>157,40</td></tr>
<tr><td>95</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>-</td><td>53,00</td><td>65,67</td><td>71,20</td><td>86,10</td><td>102,90</td><td>121,10</td><td colspan="2">139,90</td><td>160,80</td><td>179,50</td></tr>
<tr><td>96</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>-</td><td>60,30</td><td>74,80</td><td>81,20</td><td>98,10</td><td>117,20</td><td>137,80</td><td colspan="2">159,40</td><td>183,20</td><td>204,50</td></tr>
<tr><td>97</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>-</td><td>67,51</td><td>83,70</td><td>90,81</td><td>109,72</td><td>131,16</td><td>154,19</td><td colspan="2">178,32</td><td>204,92</td><td>228,76</td></tr>
<tr><td>98</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>-</td><td>76,65</td><td>95,04</td><td>103,11</td><td>124,58</td><td>148,93</td><td>175,08</td><td colspan="2">202,48</td><td>232,69</td><td>259,76</td></tr>
<tr><td>99</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>-</td><td>86,51</td><td>107,27</td><td>116,38</td><td>140,61</td><td>168,08</td><td>197,60</td><td colspan="2">228,53</td><td>262,62</td><td>293,17</td></tr>
<tr><td>100</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>-</td><td>93,03</td><td>115,35</td><td>125,15</td><td>151,20</td><td>180,75</td><td>212,49</td><td colspan="2">245,75</td><td>282,41</td><td>315,26</td></tr>
<tr><td>101</td><td rowspan="7">7000</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>-</td><td>51,43</td><td>63,77</td><td>69,18</td><td>83,59</td><td>99,92</td><td>117,47</td><td colspan="2">135,85</td><td>156,12</td><td>174,28</td></tr>
<tr><td>102</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>-</td><td>58,64</td><td>72,70</td><td>78,88</td><td>95,30</td><td>113,93</td><td>133,93</td><td colspan="2">154,90</td><td>178,00</td><td>198,71</td></tr>
<tr><td>103</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>-</td><td>66,81</td><td>82,84</td><td>89,88</td><td>108,59</td><td>129,81</td><td>152,61</td><td colspan="2">176,49</td><td>202,82</td><td>226,41</td></tr>
<tr><td>104</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>-</td><td>74,74</td><td>92,66</td><td>100,54</td><td>121,47</td><td>145,20</td><td>170,70</td><td colspan="2">197,42</td><td>226,87</td><td>253,26</td></tr>
<tr><td>105</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>-</td><td>84,86</td><td>105,22</td><td>114,16</td><td>137,93</td><td>164,88</td><td>193,83</td><td colspan="2">224,17</td><td>257,61</td><td>287,58</td></tr>
<tr><td>106</td><td>6500</td><td>-</td><td>-</td><td>-</td><td>-</td><td>95,78</td><td>118,75</td><td>128,84</td><td>155,67</td><td>186,09</td><td>218,77</td><td colspan="2">253,00</td><td>290,74</td><td>324,57</td></tr>
<tr><td>107</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>-</td><td>102,99</td><td>127,70</td><td>138,55</td><td>167,40</td><td>200,11</td><td>235,25</td><td colspan="2">272,07</td><td>312,65</td><td>349,03</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="76%"><col width="24%"></colgroup>
<tr><td rowspan="2">Гибка листов в обечайки цилиндрической формы в вальцах и сборка продольного стыка</td><td>Гибка</td></tr>
<tr><td>Карта 25, лист 9</td></tr>
</table>


<a id="p101621"></a>Примечания:
1. <a id="p101622"></a>Нормативы времени рассчитаны на гибку обечаек с предварительно подогнутыми кромками.
2. <a id="p101623"></a>Время на подгибку кромок брать по картам 22 или 23.
3. <a id="p101624"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="12%"><col width="7%"><col width="7%"><col width="6%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="8%"><col width="7%"><col width="6%"><col width="7%"><col width="7%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td><td colspan="4">Кол-во одновременно сгибаемых обечаек</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="2">Гибка листов в обечайки</td><td colspan="3">Вальцовка обечаек</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>1</td><td>2</td><td>3</td><td>4</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>цилиндрической формы</td><td>эллиптической формы</td><td>из одного листа</td><td>из двух сварных листов</td><td>из трех сварных листов</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,7</td><td>0,55</td><td>0,45</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,3</td><td>1,0</td><td>1,15</td><td>1,3</td></tr>
</table>


4. <a id="p101627"></a>Работа выполняется бригадой из двух человек:

                                  0,66    0,35    0,53
<a id="p101628"></a>                   Т = 0,00427 х Д     х L     х h    .


<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="12">Гибка листов в обечайки цилиндрической формы Гибка в горячем состоянии в вальцах</td></tr>
<tr><td colspan="12">Карта 26, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Загрузить лист в нагревательную печь.</td></tr>
<tr><td colspan="12">2. Выгрузить лист из печи и подать к вальцам. (рисунок не</td></tr>
<tr><td colspan="12">3. Заправить кромку листа в вальцы. приводится)</td></tr>
<tr><td colspan="12">4. Вальцевать лист в обечайку.</td></tr>
<tr><td colspan="12">5. Проверить обечайку по диаметру шаблоном.</td></tr>
<tr><td colspan="12">6. Снять обечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td><td>105</td><td>130</td><td>160</td></tr>
<tr><td>до</td><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="5">300</td><td>300</td><td>4,35</td><td>5,33</td><td>6,3</td><td>7,5</td><td>8,83</td><td>10,0</td><td>11,8</td><td>13,4</td><td>15,2</td></tr>
<tr><td>2</td><td>400</td><td>4,87</td><td>5,96</td><td>7,1</td><td>8,4</td><td>9,88</td><td>11,2</td><td>13,2</td><td>15,0</td><td>17,0</td></tr>
<tr><td>3</td><td>550</td><td>5,51</td><td>6,75</td><td>8,1</td><td>9,5</td><td>11,2</td><td>13,0</td><td>15,0</td><td>17,0</td><td>19,0</td></tr>
<tr><td>4</td><td>800</td><td>6,38</td><td>7,81</td><td>9,3</td><td>11,0</td><td>13,0</td><td>15,0</td><td>17,0</td><td>19,0</td><td>22,0</td></tr>
<tr><td>5</td><td>1100</td><td>7,23</td><td>8,84</td><td>11,0</td><td>13,0</td><td>15,0</td><td>17,0</td><td>19,0</td><td>22,0</td><td>25,0</td></tr>
<tr><td>6</td><td rowspan="5">400</td><td>300</td><td>5,38</td><td>6,59</td><td>7,9</td><td>9,3</td><td>11,0</td><td>12,0</td><td>15,0</td><td>16,0</td><td>19,0</td></tr>
<tr><td>7</td><td>400</td><td>6,03</td><td>7,37</td><td>8,8</td><td>10,4</td><td>12,0</td><td>14,0</td><td>16,0</td><td>19,0</td><td>21,0</td></tr>
<tr><td>8</td><td>550</td><td>6,82</td><td>8,35</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,0</td><td>19,0</td><td>21,0</td><td>24,0</td></tr>
<tr><td>9</td><td>800</td><td>7,89</td><td>9,66</td><td>12,0</td><td>14,0</td><td>16,0</td><td>18,0</td><td>21,0</td><td>24,0</td><td>27,0</td></tr>
<tr><td>10</td><td>1100</td><td>8,94</td><td>11,0</td><td>13,0</td><td>15,0</td><td>18,0</td><td>21,0</td><td>24,0</td><td>27,0</td><td>31,0</td></tr>
<tr><td>11</td><td rowspan="5">550</td><td>300</td><td>6,82</td><td>8,34</td><td>10,0</td><td>11,0</td><td>14,0</td><td>15,0</td><td>18,0</td><td>21,0</td><td>24,0</td></tr>
<tr><td>12</td><td>400</td><td>7,63</td><td>9,33</td><td>11,0</td><td>13,0</td><td>15,0</td><td>18,0</td><td>21,0</td><td>23,0</td><td>26,0</td></tr>
<tr><td>13</td><td>550</td><td>8,64</td><td>11,0</td><td>13,0</td><td>15,0</td><td>18,0</td><td>20,0</td><td>23,0</td><td>26,0</td><td>30,0</td></tr>
<tr><td>14</td><td>800</td><td>9,99</td><td>12,0</td><td>15,0</td><td>17,0</td><td>20,0</td><td>23,0</td><td>27,0</td><td>31,0</td><td>35,0</td></tr>
<tr><td>15</td><td>1100</td><td>11,0</td><td>14,0</td><td>17,0</td><td>20,0</td><td>23,0</td><td>26,0</td><td>30,0</td><td>35,0</td><td>39,0</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="12">Гибка листов в обечайки цилиндрической формы Гибка в горячем состоянии в вальцах</td></tr>
<tr><td colspan="12">Карта 26, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td><td>105</td><td>130</td><td>160</td></tr>
<tr><td>до</td><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>16</td><td rowspan="4">550</td><td>1600</td><td>13</td><td>16</td><td>19</td><td>23</td><td>26</td><td>30</td><td>35</td><td>40</td><td>146</td></tr>
<tr><td>17</td><td>2300</td><td>15</td><td>18</td><td>22</td><td>26</td><td>30</td><td>35</td><td>40</td><td>46</td><td>52</td></tr>
<tr><td>18</td><td>3200</td><td>17</td><td>21</td><td>25</td><td>30</td><td>35</td><td>40</td><td>46</td><td>52</td><td>60</td></tr>
<tr><td>19</td><td>3600</td><td>18</td><td>22</td><td>26</td><td>31</td><td>36</td><td>41</td><td>48</td><td>55</td><td>65</td></tr>
<tr><td>20</td><td rowspan="7">750</td><td>550</td><td>11</td><td>13</td><td>16</td><td>19</td><td>22</td><td>25</td><td>29</td><td>33</td><td>38</td></tr>
<tr><td>21</td><td>800</td><td>13</td><td>15</td><td>18</td><td>22</td><td>25</td><td>29</td><td>34</td><td>38</td><td>44</td></tr>
<tr><td>22</td><td>1100</td><td>14</td><td>17</td><td>21</td><td>25</td><td>29</td><td>33</td><td>38</td><td>44</td><td>49</td></tr>
<tr><td>23</td><td>1600</td><td>16</td><td>20</td><td>24</td><td>29</td><td>33</td><td>38</td><td>44</td><td>51</td><td>57</td></tr>
<tr><td>24</td><td>2300</td><td>19</td><td>23</td><td>28</td><td>33</td><td>38</td><td>44</td><td>51</td><td>58</td><td>66</td></tr>
<tr><td>25</td><td>3200</td><td>22</td><td>26</td><td>31</td><td>37</td><td>44</td><td>50</td><td>58</td><td>66</td><td>75</td></tr>
<tr><td>26</td><td>3600</td><td>23</td><td>28</td><td>33</td><td>39</td><td>46</td><td>52</td><td>61</td><td>69</td><td>79</td></tr>
<tr><td>27</td><td rowspan="7">1100</td><td>550</td><td>13</td><td>16</td><td>20</td><td>23</td><td>27</td><td>31</td><td>36</td><td>41</td><td>47</td></tr>
<tr><td>28</td><td>860</td><td>16</td><td>20</td><td>23</td><td>27</td><td>31</td><td>36</td><td>42</td><td>47</td><td>54</td></tr>
<tr><td>29</td><td>1100</td><td>18</td><td>22</td><td>26</td><td>31</td><td>36</td><td>41</td><td>47</td><td>54</td><td>61</td></tr>
<tr><td>30</td><td>1600</td><td>20</td><td>25</td><td>30</td><td>35</td><td>41</td><td>47</td><td>55</td><td>62</td><td>71</td></tr>
<tr><td>31</td><td>2300</td><td>23</td><td>29</td><td>35</td><td>41</td><td>47</td><td>54</td><td>63</td><td>72</td><td>82</td></tr>
<tr><td>32</td><td>3200</td><td>27</td><td>33</td><td>40</td><td>46</td><td>54</td><td>61</td><td>72</td><td>82</td><td>93</td></tr>
<tr><td>33</td><td>3600</td><td>28</td><td>34</td><td>41</td><td>48</td><td>56</td><td>64</td><td>75</td><td>86</td><td>97</td></tr>
<tr><td>34</td><td rowspan="7">1400</td><td>550</td><td>16</td><td>20</td><td>24</td><td>28</td><td>33</td><td>38</td><td>44</td><td>51</td><td>57</td></tr>
<tr><td>35</td><td>800</td><td>20</td><td>24</td><td>29</td><td>34</td><td>40</td><td>45</td><td>53</td><td>61</td><td>69</td></tr>
<tr><td>36</td><td>1100</td><td>23</td><td>28</td><td>33</td><td>39</td><td>45</td><td>52</td><td>61</td><td>69</td><td>79</td></tr>
<tr><td>37</td><td>1600</td><td>26</td><td>32</td><td>38</td><td>45</td><td>53</td><td>60</td><td>70</td><td>80</td><td>91</td></tr>
<tr><td>38</td><td>2300</td><td>30</td><td>37</td><td>44</td><td>52</td><td>60</td><td>69</td><td>81</td><td>92</td><td>105</td></tr>
<tr><td>39</td><td>3200</td><td>34</td><td>42</td><td>50</td><td>59</td><td>69</td><td>79</td><td>92</td><td>105</td><td>119</td></tr>
<tr><td>40</td><td>3600</td><td>36</td><td>44</td><td>53</td><td>62</td><td>73</td><td>82</td><td>97</td><td>110</td><td>125</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="12">Гибка листов в обечайки цилиндрической формы Гибка в горячем состоянии в вальцах</td></tr>
<tr><td colspan="12">Карта 26, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td><td>105</td><td>130</td><td>160</td></tr>
<tr><td>до</td><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>41</td><td rowspan="7">1800</td><td>800</td><td>24,0</td><td>29,0</td><td>35,0</td><td>42,0</td><td>49,0</td><td>55,0</td><td>65,0</td><td>74,0</td><td>84,0</td></tr>
<tr><td>42</td><td>1100</td><td>27,0</td><td>33,0</td><td>40,0</td><td>47,0</td><td>55,0</td><td>62,0</td><td>74,0</td><td>84,0</td><td>95,0</td></tr>
<tr><td>43</td><td>1600</td><td>32,0</td><td>39,0</td><td>46,0</td><td>55,0</td><td>64,0</td><td>72,0</td><td>85,0</td><td>96,0</td><td>110,0</td></tr>
<tr><td>44</td><td>2300</td><td>36,0</td><td>44,0</td><td>53,0</td><td>63,0</td><td>73,0</td><td>83,0</td><td>98,0</td><td>111,0</td><td>126,0</td></tr>
<tr><td>45</td><td>3200</td><td>41,0</td><td>51,0</td><td>61,0</td><td>72,0</td><td>83,0</td><td>95,0</td><td>111,0</td><td>126,0</td><td>144,0</td></tr>
<tr><td>46</td><td>4600</td><td>48,0</td><td>58,0</td><td>70,0</td><td>82,0</td><td>95,0</td><td>109,0</td><td>120,0</td><td>146,0</td><td>165,0</td></tr>
<tr><td>47</td><td>6500</td><td>54,0</td><td>67,0</td><td>80,0</td><td>94,0</td><td>110,0</td><td>125,0</td><td>147,0</td><td>167,0</td><td>189,0</td></tr>
<tr><td>48</td><td rowspan="7">2400</td><td>800</td><td>30,0</td><td>36,0</td><td>44,0</td><td>52,0</td><td>60,0</td><td>68,0</td><td>80,0</td><td>91,0</td><td>103,0</td></tr>
<tr><td>49</td><td>1100</td><td>34,0</td><td>41,0</td><td>50,0</td><td>58,0</td><td>68,0</td><td>77,0</td><td>91,0</td><td>103,0</td><td>117,0</td></tr>
<tr><td>50</td><td>1600</td><td>39,0</td><td>48,0</td><td>57,0</td><td>68,0</td><td>79,0</td><td>89,0</td><td>105,0</td><td>119,0</td><td>136,0</td></tr>
<tr><td>51</td><td>2300</td><td>45,0</td><td>55,0</td><td>66,0</td><td>78,0</td><td>91,0</td><td>103,0</td><td>121,0</td><td>138,0</td><td>156,0</td></tr>
<tr><td>52</td><td>3200</td><td>51,0</td><td>62,0</td><td>75,0</td><td>88,0</td><td>103,0</td><td>117,0</td><td>138,0</td><td>157,0</td><td>178,0</td></tr>
<tr><td>53</td><td>4600</td><td>59,0</td><td>72,0</td><td>87,0</td><td>102,0</td><td>119,0</td><td>135,0</td><td>159,0</td><td>180,0</td><td>205,0</td></tr>
<tr><td>54</td><td>6500</td><td>67,0</td><td>82,0</td><td>99,0</td><td>117,0</td><td>136,0</td><td>155,0</td><td>182,0</td><td>206,0</td><td>234,0</td></tr>
<tr><td>55</td><td rowspan="7">3200</td><td>1100</td><td>42,0</td><td>51,0</td><td>61,0</td><td>72,0</td><td>84,0</td><td>96,0</td><td>113,0</td><td>128,0</td><td>145,0</td></tr>
<tr><td>56</td><td>1600</td><td>48,0</td><td>59,0</td><td>71,0</td><td>84,0</td><td>97,0</td><td>111,0</td><td>130,0</td><td>148,0</td><td>168,0</td></tr>
<tr><td>57</td><td>2300</td><td>56,0</td><td>68,0</td><td>82,0</td><td>96,0</td><td>112,0</td><td>128,0</td><td>150,0</td><td>170,0</td><td>193,0</td></tr>
<tr><td>58</td><td>3200</td><td>64,0</td><td>77,0</td><td>93,0</td><td>111,0</td><td>128,0</td><td>145,0</td><td>170,0</td><td>194,0</td><td>220,0</td></tr>
<tr><td>59</td><td>4500</td><td>73,0</td><td>89,0</td><td>107,0</td><td>126,0</td><td>147,0</td><td>167,0</td><td>196,0</td><td>223,0</td><td>253,0</td></tr>
<tr><td>60</td><td>6500</td><td>83,0</td><td>102,0</td><td>122,0</td><td>144,0</td><td>169,0</td><td>191,0</td><td>225,0</td><td>256,0</td><td>289,0</td></tr>
<tr><td>61</td><td>3000</td><td>90,0</td><td>111,0</td><td>133,0</td><td>156,0</td><td>183,0</td><td>207,0</td><td>244,0</td><td>277,0</td><td>314,0</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="12">Гибка листов в обечайки цилиндрической формы Гибка в горячем состоянии в вальцах</td></tr>
<tr><td colspan="12">Карта 26, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td><td>105</td><td>130</td><td>160</td></tr>
<tr><td>до</td><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>62</td><td rowspan="7">4000</td><td>1100</td><td>49,0</td><td>60,0</td><td>72,0</td><td>85,0</td><td>100,0</td><td>113,0</td><td>133,0</td><td>151,0</td><td>171,0</td></tr>
<tr><td>63</td><td>1600</td><td>57,0</td><td>70,0</td><td>84,0</td><td>99,0</td><td>115,0</td><td>113,0</td><td>153,0</td><td>174,0</td><td>198,0</td></tr>
<tr><td>64</td><td>2300</td><td>65,0</td><td>80,0</td><td>96,0</td><td>114,0</td><td>133,0</td><td>151,0</td><td>177,0</td><td>201,0</td><td>228,0</td></tr>
<tr><td>65</td><td>3200</td><td>74,0</td><td>91,0</td><td>109,0</td><td>129,0</td><td>151,0</td><td>171,0</td><td>201,0</td><td>229,0</td><td>259,0</td></tr>
<tr><td>66</td><td>4600</td><td>86,0</td><td>105,0</td><td>126,0</td><td>149,0</td><td>174,0</td><td>197,0</td><td>232,0</td><td>264,0</td><td>299,0</td></tr>
<tr><td>67</td><td>6500</td><td>98,0</td><td>120,0</td><td>145,0</td><td>170,0</td><td>199,0</td><td>226,0</td><td>265,0</td><td>302,0</td><td>342,0</td></tr>
<tr><td>68</td><td>8000</td><td>106,0</td><td>131,0</td><td>157,0</td><td>185,0</td><td>216,0</td><td>245,0</td><td>288,0</td><td>327,0</td><td>371,0</td></tr>
<tr><td>69</td><td rowspan="7">5000</td><td>1100</td><td>58,0</td><td>71,0</td><td>85,0</td><td>100,0</td><td>118,0</td><td>133,0</td><td>157,0</td><td>178,0</td><td>202,0</td></tr>
<tr><td>70</td><td>1600</td><td>68,0</td><td>82,0</td><td>99,0</td><td>116,0</td><td>136,0</td><td>154,0</td><td>181,0</td><td>206,0</td><td>233,0</td></tr>
<tr><td>71</td><td>2300</td><td>77,0</td><td>95,0</td><td>114,0</td><td>134,0</td><td>157,0</td><td>177,0</td><td>209,0</td><td>237,0</td><td>269,0</td></tr>
<tr><td>72</td><td>3200</td><td>88,0</td><td>108,0</td><td>129,0</td><td>152,0</td><td>178,0</td><td>202,0</td><td>238,0</td><td>270,0</td><td>306,0</td></tr>
<tr><td>73</td><td>4600</td><td>101,0</td><td>124,0</td><td>149,0</td><td>175,0</td><td>204,0</td><td>234,0</td><td>274,0</td><td>311,0</td><td>352,0</td></tr>
<tr><td>74</td><td>6500</td><td>116,0</td><td>142,0</td><td>170,0</td><td>201,0</td><td>235,0</td><td>266,0</td><td>313,0</td><td>356,0</td><td>403,0</td></tr>
<tr><td>75</td><td>8000</td><td>126,0</td><td>154,0</td><td>185,0</td><td>218,0</td><td>255,0</td><td>288,0</td><td>340,0</td><td>386,0</td><td>437,0</td></tr>
<tr><td>76</td><td rowspan="7">6000</td><td>1100</td><td>66,0</td><td>82,0</td><td>97,0</td><td>115,0</td><td>134,0</td><td>152,0</td><td>179,0</td><td>203,0</td><td>231,0</td></tr>
<tr><td>77</td><td>1600</td><td>77,0</td><td>94,0</td><td>113,0</td><td>133,0</td><td>155,0</td><td>176,0</td><td>207,0</td><td>236,0</td><td>267,0</td></tr>
<tr><td>78</td><td>2300</td><td>88,0</td><td>108,0</td><td>130,0</td><td>153,0</td><td>179,0</td><td>203,0</td><td>239,0</td><td>271,0</td><td>308,0</td></tr>
<tr><td>79</td><td>3200</td><td>101,0</td><td>123,0</td><td>148,0</td><td>174,0</td><td>204,0</td><td>231,0</td><td>272,0</td><td>309,0</td><td>350,0</td></tr>
<tr><td>80</td><td>4600</td><td>116,0</td><td>142,0</td><td>170,0</td><td>201,0</td><td>235,0</td><td>266,0</td><td>313,0</td><td>356,0</td><td>403,0</td></tr>
<tr><td>81</td><td>6500</td><td>132,0</td><td>162,0</td><td>194,0</td><td>230,0</td><td>269,0</td><td>305,0</td><td>358,0</td><td>408,0</td><td>462,0</td></tr>
<tr><td>82</td><td>3000</td><td>144,0</td><td>176,0</td><td>211,0</td><td>250,0</td><td>292,0</td><td>330,0</td><td>389,0</td><td>442,0</td><td>500,0</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="12">Гибка листов в обечайки цилиндрической формы Гибка в горячем состоянии в вальцах</td></tr>
<tr><td colspan="12">Карта 26, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td><td>105</td><td>130</td><td>160</td></tr>
<tr><td>до</td><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>83</td><td rowspan="7">7000</td><td>1100</td><td>74,0</td><td>91,0</td><td>109,0</td><td>129,0</td><td>151,0</td><td>171,0</td><td>201,0</td><td>228,0</td><td>259,0</td></tr>
<tr><td>84</td><td>1600</td><td>86,0</td><td>105,0</td><td>126,0</td><td>144,0</td><td>174,0</td><td>198,0</td><td>233,0</td><td>264,0</td><td>299,0</td></tr>
<tr><td>85</td><td>2300</td><td>99,0</td><td>121,0</td><td>146,0</td><td>172,0</td><td>201,0</td><td>228,0</td><td>268,0</td><td>305,0</td><td>345,0</td></tr>
<tr><td>86</td><td>3200</td><td>113,0</td><td>134,0</td><td>166,0</td><td>195,0</td><td>228,0</td><td>259,0</td><td>305,0</td><td>345,0</td><td>392,0</td></tr>
<tr><td>87</td><td>4600</td><td>130,0</td><td>159,0</td><td>191,0</td><td>225,0</td><td>263,0</td><td>298,4</td><td>351,0</td><td>399,0</td><td>452,0</td></tr>
<tr><td>88</td><td>6500</td><td>149,0</td><td>182,0</td><td>218,0</td><td>258,0</td><td>301,0</td><td>341,0</td><td>402,0</td><td>457,0</td><td>517,0</td></tr>
<tr><td>89</td><td>8000</td><td>161,0</td><td>197,0</td><td>237,0</td><td>279,0</td><td>326,0</td><td>370,0</td><td>435,0</td><td>495,0</td><td>561,0</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p101747"></a>Примечания: 1. При измененных условиях гибки приведенное в нормативной карте время применяется коэффициентами:


<table>
<colgroup><col width="19%"><col width="9%"><col width="8%"><col width="8%"><col width="12%"><col width="12%"><col width="9%"><col width="11%"><col width="11%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="2">Гибка листов в обечайки</td><td colspan="3">Вальцовка обечаек</td></tr>
<tr><td>нормы времени</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>цилиндрической формы</td><td>эллиптической формы</td><td>из одного листа</td><td>из двух сварных листов</td><td>из трех сварных листов</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,3</td><td>1,0</td><td>1,15</td><td>1,3</td></tr>
</table>


2. <a id="p101750"></a>Работа выполняется бригадой из двух человек:

                                   0,74    0,39    0,6
<a id="p101751"></a>                   Т = 0,001146 х Д     х L     х h   .


<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="7%"><col width="8%"><col width="8%"><col width="7%"><col width="8%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="10" rowspan="2">Гибка листов в обечайки конической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 27, лист 1</td></tr>
<tr><td colspan="14">Содержание работы</td></tr>
<tr><td colspan="14">1. Подать лист к вальцам.</td></tr>
<tr><td colspan="14">2. Заправить кромку листа в вальцы. (рисунок не</td></tr>
<tr><td colspan="14">3. Вальцевать лист в обечайку. приводится)</td></tr>
<tr><td colspan="14">4. Проверить обечайку по диаметрам шаблонами.</td></tr>
<tr><td colspan="14">5. Снять обечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="11">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td colspan="2">20</td><td>28</td><td>38</td><td>50</td></tr>
<tr><td>до</td><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="5">300</td><td>300</td><td>3,14</td><td>3,65</td><td>4,52</td><td>5,24</td><td>6,47</td><td>7,0</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>400</td><td>3,51</td><td>4,08</td><td>5,04</td><td>5,85</td><td>7,22</td><td>7,8</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>550</td><td>3,96</td><td>4,60</td><td>5,68</td><td>6,60</td><td>8,15</td><td>8,8</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>800</td><td>4,57</td><td>5,31</td><td>6,55</td><td>7,61</td><td>9,40</td><td>10,2</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>1100</td><td>5,16</td><td>5,99</td><td>7,39</td><td>8,59</td><td>10,6</td><td>11,5</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td rowspan="5">400</td><td>300</td><td>3,78</td><td>4,39</td><td>5,42</td><td>6,30</td><td>7,78</td><td>8,4</td><td colspan="2">10,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>400</td><td>4,22</td><td>4,9</td><td>6,05</td><td>7,03</td><td>8,68</td><td>9,4</td><td colspan="2">11,3</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>550</td><td>4,76</td><td>5,53</td><td>6,83</td><td>7,93</td><td>9,80</td><td>10,6</td><td colspan="2">12,8</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>800</td><td>5,49</td><td>6,38</td><td>7,88</td><td>9,15</td><td>11,3</td><td>12,2</td><td colspan="2">14,7</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>1100</td><td>6,20</td><td>7,20</td><td>8,89</td><td>10,3</td><td>12,8</td><td>13,8</td><td colspan="2">16,6</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td rowspan="6">550</td><td>300</td><td>4,64</td><td>5,39</td><td>6,55</td><td>7,73</td><td>9,65</td><td>10,3</td><td colspan="2">12,4</td><td>14,8</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>400</td><td>5,18</td><td>6,01</td><td>7,42</td><td>8,62</td><td>106,0</td><td>11,5</td><td colspan="2">13,9</td><td>16,5</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>550</td><td>5,84</td><td>6,78</td><td>8,38</td><td>9,73</td><td>120,0</td><td>13,0</td><td colspan="2">15,7</td><td>18,7</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td>800</td><td>6,73</td><td>7,82</td><td>9,66</td><td>11,2</td><td>138,0</td><td>15,0</td><td colspan="2">18,0</td><td>21,5</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>1100</td><td>7,61</td><td>8,83</td><td>10,90</td><td>12,7</td><td>156,0</td><td>16,9</td><td colspan="2">20,4</td><td>24,3</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>1600</td><td>8,77</td><td>10,20</td><td>12,30</td><td>14,6</td><td>18,00</td><td>19,5</td><td colspan="2">23,5</td><td>28,0</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="10" rowspan="2">Гибка листов в обечайки конической формы в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 27, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Большой диаметр</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="10">Толщина металла h, мм, до</td></tr>
<tr><td>обечайки Д, мм,</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td>50</td></tr>
<tr><td>до</td><td>до</td><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>17</td><td rowspan="7">750</td><td>300</td><td>5,00</td><td>5,8</td><td>7,1</td><td>8,3</td><td>10,3</td><td>11,1</td><td>13,4</td><td>15,9</td><td>18,7</td><td>-</td></tr>
<tr><td>18</td><td>400</td><td>5,58</td><td>6,4</td><td>8,0</td><td>9,3</td><td>11,5</td><td>12,4</td><td>14,9</td><td>17,8</td><td>20,9</td><td>-</td></tr>
<tr><td>19</td><td>550</td><td>6,30</td><td>7,3</td><td>9,0</td><td>10,5</td><td>12,9</td><td>14,0</td><td>16,9</td><td>20,1</td><td>23,6</td><td>-</td></tr>
<tr><td>20</td><td>800</td><td>7,26</td><td>8,4</td><td>10,4</td><td>12,1</td><td>14,9</td><td>16,2</td><td>19,5</td><td>23,2</td><td>27,2</td><td>-</td></tr>
<tr><td>21</td><td>1100</td><td>8,20</td><td>9,5</td><td>11,8</td><td>13,7</td><td>16,9</td><td>18,3</td><td>21,9</td><td>26,2</td><td>30,7</td><td>-</td></tr>
<tr><td>22</td><td>1600</td><td>9,45</td><td>10,9</td><td>13,6</td><td>15,7</td><td>19,4</td><td>21,1</td><td>25,4</td><td>30,2</td><td>35,4</td><td>-</td></tr>
<tr><td>23</td><td>2300</td><td>10,8</td><td>12,6</td><td>15,6</td><td>18,1</td><td>22,3</td><td>24,2</td><td>29,1</td><td>34,7</td><td>40,6</td><td>-</td></tr>
<tr><td>24</td><td rowspan="7">1000</td><td>300</td><td>-</td><td>7,9</td><td>9,7</td><td>11,3</td><td>13,0</td><td>15,1</td><td>18,2</td><td>21,7</td><td>25,5</td><td>29,4</td></tr>
<tr><td>25</td><td>400</td><td>-</td><td>8,8</td><td>10,9</td><td>12,6</td><td>15,6</td><td>16,9</td><td>20,4</td><td>24,5</td><td>28,4</td><td>32,8</td></tr>
<tr><td>26</td><td>550</td><td>-</td><td>9,9</td><td>12,3</td><td>14,3</td><td>17,6</td><td>19,1</td><td>22,9</td><td>27,4</td><td>32,1</td><td>37,0</td></tr>
<tr><td>27</td><td>800</td><td>-</td><td>11,5</td><td>14,1</td><td>16,4</td><td>20,3</td><td>22,0</td><td>26,5</td><td>31,6</td><td>37,1</td><td>42,6</td></tr>
<tr><td>28</td><td>1100</td><td>-</td><td>12,9</td><td>15,9</td><td>18,5</td><td>22,9</td><td>24,8</td><td>29,9</td><td>35,6</td><td>41,7</td><td>48,1</td></tr>
<tr><td>29</td><td>1600</td><td>-</td><td>14,9</td><td>18,4</td><td>21,4</td><td>26,4</td><td>28,6</td><td>34,5</td><td>41,1</td><td>48,1</td><td>55,5</td></tr>
<tr><td>30</td><td>2300</td><td>-</td><td>17,1</td><td>21,1</td><td>24,6</td><td>30,3</td><td>32,9</td><td>39,6</td><td>47,1</td><td>55,2</td><td>63,7</td></tr>
<tr><td>31</td><td rowspan="5">1350</td><td>550</td><td>-</td><td>12,0</td><td>14,9</td><td>17,3</td><td>21,3</td><td>23,1</td><td>27,8</td><td>33,2</td><td>38,9</td><td>44,8</td></tr>
<tr><td>32</td><td>800</td><td>-</td><td>13,9</td><td>17,7</td><td>19,9</td><td>24,7</td><td>26,7</td><td>32,1</td><td>38,2</td><td>44,8</td><td>51,7</td></tr>
<tr><td>33</td><td>1000</td><td>-</td><td>15,6</td><td>19,4</td><td>22,5</td><td>27,8</td><td>30,1</td><td>36,2</td><td>43,2</td><td>50,6</td><td>58,4</td></tr>
<tr><td>34</td><td>1600</td><td>-</td><td>18,1</td><td>22,2</td><td>25,9</td><td>32,0</td><td>34,7</td><td>41,8</td><td>49,8</td><td>58,3</td><td>67,3</td></tr>
<tr><td>35</td><td>2300</td><td>-</td><td>20,7</td><td>25,6</td><td>29,8</td><td>36,8</td><td>39,8</td><td>47,9</td><td>58,8</td><td>66,9</td><td>77,2</td></tr>
<tr><td>36</td><td rowspan="5">1800</td><td>550</td><td>-</td><td>14,5</td><td>17,9</td><td>20,8</td><td>25,7</td><td>27,8</td><td>33,5</td><td>39,9</td><td>46,7</td><td>53,9</td></tr>
<tr><td>37</td><td>800</td><td>-</td><td>16,7</td><td>20,6</td><td>24,0</td><td>29,6</td><td>32,0</td><td>38,6</td><td>45,9</td><td>53,9</td><td>62,1</td></tr>
<tr><td>38</td><td>1100</td><td>-</td><td>18,9</td><td>23,3</td><td>27,0</td><td>33,4</td><td>36,2</td><td>43,6</td><td>51,9</td><td>60,8</td><td>70,1</td></tr>
<tr><td>39</td><td>1600</td><td>-</td><td>21,8</td><td>26,8</td><td>31,2</td><td>38,5</td><td>41,7</td><td>50,2</td><td>39,8</td><td>70,1</td><td>80,9</td></tr>
<tr><td>40</td><td>2300</td><td>-</td><td>24,9</td><td>30,8</td><td>35,8</td><td>44,2</td><td>47,9</td><td>54,4</td><td>68,7</td><td>80,5</td><td>92,8</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="10" rowspan="2">Гибка листов в обечайки конической формы в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 27, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Большой диаметр</td><td rowspan="2">Длина обечайки L, мм,</td><td colspan="10">Толщина металла h, мм, до</td></tr>
<tr><td>обечайки Д, мм,</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td>50</td></tr>
<tr><td>до</td><td>до</td><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>41</td><td rowspan="6">2400</td><td>550</td><td>-</td><td>17,4</td><td>21,5</td><td>24,9</td><td>30,8</td><td>33,4</td><td>40,2</td><td>47,9</td><td>56,2</td><td>64,8</td></tr>
<tr><td>42</td><td>800</td><td>-</td><td>20,1</td><td>24,8</td><td>28,8</td><td>35,6</td><td>38,5</td><td>46,4</td><td>55,3</td><td>64,8</td><td>74,7</td></tr>
<tr><td>43</td><td>1100</td><td>-</td><td>22,7</td><td>28,0</td><td>32,5</td><td>40,1</td><td>43,5</td><td>52,4</td><td>62,4</td><td>73,1</td><td>84,3</td></tr>
<tr><td>44</td><td>1600</td><td>-</td><td>26,1</td><td>32,3</td><td>37,5</td><td>46,3</td><td>50,1</td><td>60,4</td><td>71,9</td><td>84,3</td><td>97,2</td></tr>
<tr><td>45</td><td>2300</td><td>-</td><td>30,0</td><td>37,1</td><td>43,0</td><td>53,1</td><td>57,6</td><td>69,3</td><td>82,6</td><td>97,0</td><td>111,5</td></tr>
<tr><td>46</td><td>3200</td><td>-</td><td>34,0</td><td>42,0</td><td>48,8</td><td>60,2</td><td>65,3</td><td>78,6</td><td>93,6</td><td>110,0</td><td>126,5</td></tr>
<tr><td>47</td><td rowspan="6">3200</td><td>550</td><td>-</td><td>21,0</td><td>25,8</td><td>30,0</td><td>37,0</td><td>40,0</td><td>48,3</td><td>57,4</td><td>67,5</td><td>77,8</td></tr>
<tr><td>48</td><td>800</td><td>-</td><td>24,1</td><td>30,0</td><td>34,6</td><td>42,8</td><td>46,3</td><td>55,8</td><td>66,4</td><td>77,9</td><td>89,8</td></tr>
<tr><td>49</td><td>1100</td><td>-</td><td>27,3</td><td>33,7</td><td>39,1</td><td>48,0</td><td>52,3</td><td>62,9</td><td>74,9</td><td>88,0</td><td>101,4</td></tr>
<tr><td>50</td><td>1600</td><td>-</td><td>31,4</td><td>38,8</td><td>45,1</td><td>55,6</td><td>60,3</td><td>72,6</td><td>86,5</td><td>101,3</td><td>116,9</td></tr>
<tr><td>51</td><td>2300</td><td>-</td><td>36,1</td><td>44,6</td><td>51,7</td><td>63,9</td><td>69,2</td><td>83,3</td><td>99,2</td><td>116,3</td><td>134,2</td></tr>
<tr><td>52</td><td>3200</td><td>-</td><td>41,0</td><td>50,5</td><td>58,6</td><td>72,5</td><td>78,5</td><td>94,5</td><td>112,5</td><td>131,9</td><td>152,1</td></tr>
<tr><td>53</td><td rowspan="7">4000</td><td>550</td><td>-</td><td>-</td><td>29,8</td><td>34,6</td><td>42,8</td><td>46,9</td><td>55,8</td><td>60,5</td><td>77,9</td><td>89,9</td></tr>
<tr><td>54</td><td>800</td><td>-</td><td>-</td><td>34,4</td><td>40,0</td><td>49,3</td><td>53,3</td><td>64,3</td><td>76,6</td><td>89,8</td><td>103,6</td></tr>
<tr><td>55</td><td>1100</td><td>-</td><td>-</td><td>38,8</td><td>45,1</td><td>55,6</td><td>60,3</td><td>72,6</td><td>86,5</td><td>101,4</td><td>116,9</td></tr>
<tr><td>56</td><td>1600</td><td>-</td><td>-</td><td>44,8</td><td>52,0</td><td>64,2</td><td>69,6</td><td>83,7</td><td>99,7</td><td>116,9</td><td>134,8</td></tr>
<tr><td>57</td><td>2300</td><td>-</td><td>-</td><td>51,4</td><td>59,7</td><td>73,7</td><td>79,8</td><td>96,1</td><td>114,5</td><td>134,2</td><td>154,8</td></tr>
<tr><td>58</td><td>3200</td><td>-</td><td>-</td><td>58,3</td><td>57,7</td><td>83,5</td><td>90,5</td><td>108,9</td><td>129,8</td><td>152,1</td><td>175,5</td></tr>
<tr><td>59</td><td>4600</td><td>-</td><td>-</td><td>67,0</td><td>77,7</td><td>95,9</td><td>104,0</td><td>125,1</td><td>148,9</td><td>174,6</td><td>201,4</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="76%"><col width="24%"></colgroup>
<tr><td rowspan="2">Гибка листов в обечайки конической формы в вальцах</td><td>Гибка</td></tr>
<tr><td>Карта 27, лист 4</td></tr>
</table>


<a id="p101831"></a>Примечания:
1. <a id="p101832"></a>Нормативы времени рассчитаны на гибку обечаек в холодном состоянии с предварительно подогнутыми кромками.
2. <a id="p101833"></a>Время на подгибку кромок брать по картам 22 и 23.
3. <a id="p101834"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="14%"><col width="10%"><col width="10%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="3">Угол альфа у основания конической обечайки, град.</td><td colspan="3">Вальцовка обечаек</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>альфа &lt;= 45</td><td>альфа от 45 - 60</td><td>альфа &gt; 60</td><td>из одного листа</td><td>из двух сварных листов</td><td>из трех сварных листов</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,2</td><td>1,0</td><td>0,9</td><td>1,35</td><td>1,2</td><td>1,0</td><td>1,0</td><td>1,15</td><td>1,3</td></tr>
</table>


4. <a id="p101837"></a>Работа выполняется бригадой из двух человек:

                                  0,64    0,38    0,52
<a id="p101838"></a>                   Т = 0,00529 х Д     х L     х h    .


<table>
<colgroup><col width="5%"><col width="16%"><col width="14%"><col width="11%"><col width="11%"><col width="11%"><col width="8%"><col width="3%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="7" rowspan="2">Гибка листов в обечайки конической формы в горячем состоянии в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 28, лист 1</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Загрузить лист в нагревательную печь.</td></tr>
<tr><td colspan="10">2. Выгрузить лист из печи и подать к вальцам.</td></tr>
<tr><td colspan="10">3. Заправить кромку листа в вальцы. (рисунок не</td></tr>
<tr><td colspan="10">4. Вальцевать лист в обечайку. приводится)</td></tr>
<tr><td colspan="10">5. Проверить обечайку по диаметрам шаблонами.</td></tr>
<tr><td colspan="10">6. Снять обечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Большой диаметр</td><td>Длина обечайки</td><td colspan="7">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">обечайки Д, мм, до</td><td rowspan="2">L, мм, до</td><td>20</td><td>28</td><td>38</td><td colspan="2">50</td><td>65</td><td>80</td></tr>
<tr><td colspan="7">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="5">550</td><td>400</td><td>18,4</td><td>22,1</td><td>26,1</td><td colspan="2">30,4</td><td>35,1</td><td>39,4</td></tr>
<tr><td>2</td><td>550</td><td>21,0</td><td>25,3</td><td>30,0</td><td colspan="2">35,0</td><td>40,2</td><td>45,0</td></tr>
<tr><td>3</td><td>800</td><td>23,6</td><td>28,4</td><td>33,6</td><td colspan="2">39,1</td><td>45,1</td><td>50,6</td></tr>
<tr><td>4</td><td>1100</td><td>26,4</td><td>31,8</td><td>37,6</td><td colspan="2">43,7</td><td>50,5</td><td>56,6</td></tr>
<tr><td>5</td><td>1600</td><td>30,2</td><td>36,4</td><td>43,0</td><td colspan="2">50,1</td><td>57,6</td><td>64,8</td></tr>
<tr><td>6</td><td rowspan="5">750</td><td>550</td><td>25,4</td><td>30,6</td><td>36,2</td><td colspan="2">42,1</td><td>48,6</td><td>54,5</td></tr>
<tr><td>7</td><td>800</td><td>29,1</td><td>35,0</td><td>41,4</td><td colspan="2">48,2</td><td>55,6</td><td>62,4</td></tr>
<tr><td>8</td><td>1100</td><td>32,6</td><td>39,3</td><td>46,4</td><td colspan="2">54,0</td><td>62,4</td><td>64,9</td></tr>
<tr><td>9</td><td>1600</td><td>37,4</td><td>44,9</td><td>53,2</td><td colspan="2">61,8</td><td>71,4</td><td>80,0</td></tr>
<tr><td>10</td><td>2300</td><td>42,6</td><td>51,2</td><td>60,6</td><td colspan="2">70,4</td><td>81,4</td><td>91,2</td></tr>
<tr><td>11</td><td rowspan="3">10000</td><td>550</td><td>30,9</td><td>37,2</td><td>44,0</td><td colspan="2">51,2</td><td>59,1</td><td>66,3</td></tr>
<tr><td>12</td><td>800</td><td>35,4</td><td>42,6</td><td>50,4</td><td colspan="2">58,6</td><td>67,7</td><td>75,9</td></tr>
<tr><td>13</td><td>1100</td><td>39,7</td><td>47,7</td><td>56,5</td><td colspan="2">65,7</td><td>75,9</td><td>85,1</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="16%"><col width="14%"><col width="11%"><col width="11%"><col width="11%"><col width="8%"><col width="3%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="7" rowspan="2">Гибка листов в обечайки конической формы в горячем состоянии в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 28, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Большой диаметр</td><td>Длина обечайки</td><td colspan="7">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">обечайки Д, мм, до</td><td rowspan="2">L, мм, до</td><td>20</td><td>28</td><td>38</td><td colspan="2">50</td><td>65</td><td>80</td></tr>
<tr><td colspan="7">Время Т, чел.-мин.</td></tr>
<tr><td>14</td><td rowspan="2">10000</td><td>1600</td><td>45,4</td><td>54,6</td><td>64,6</td><td colspan="2">75,2</td><td>86,8</td><td>97,3</td></tr>
<tr><td>15</td><td>2300</td><td>50,3</td><td>60,6</td><td>71,6</td><td colspan="2">83,3</td><td>96,3</td><td>107,9</td></tr>
<tr><td>16</td><td rowspan="5">1350</td><td>550</td><td>37,9</td><td>45,6</td><td>53,9</td><td colspan="2">62,8</td><td>72,5</td><td>81,3</td></tr>
<tr><td>17</td><td>800</td><td>43,4</td><td>52,2</td><td>61,8</td><td colspan="2">71,8</td><td>82,9</td><td>93,0</td></tr>
<tr><td>18</td><td>1100</td><td>48,7</td><td>58,6</td><td>69,3</td><td colspan="2">80,6</td><td>93,1</td><td>104,3</td></tr>
<tr><td>19</td><td>1600</td><td>55,7</td><td>67,0</td><td>79,3</td><td colspan="2">92,2</td><td>106,5</td><td>119,4</td></tr>
<tr><td>20</td><td>2300</td><td>63,5</td><td>76,4</td><td>90,3</td><td colspan="2">105,1</td><td>124,4</td><td>136,1</td></tr>
<tr><td>21</td><td rowspan="5">1800</td><td>550</td><td>46,1</td><td>55,5</td><td>65,6</td><td colspan="2">76,3</td><td>88,2</td><td>98,6</td></tr>
<tr><td>22</td><td>800</td><td>52,8</td><td>63,5</td><td>75,1</td><td colspan="2">87,4</td><td>100,0</td><td>113,1</td></tr>
<tr><td>23</td><td>1100</td><td>59,2</td><td>71,2</td><td>84,2</td><td colspan="2">97,9</td><td>113,2</td><td>126,9</td></tr>
<tr><td>24</td><td>1600</td><td>67,7</td><td>81,5</td><td>96,4</td><td colspan="2">112,1</td><td>129,5</td><td>145,2</td></tr>
<tr><td>25</td><td>2300</td><td>77,2</td><td>92,9</td><td>109,9</td><td colspan="2">127,8</td><td>147,6</td><td>165,4</td></tr>
<tr><td>26</td><td rowspan="6">2400</td><td>550</td><td>56,1</td><td>67,5</td><td>79,8</td><td colspan="2">92,8</td><td>107,2</td><td>120,2</td></tr>
<tr><td>27</td><td>800</td><td>64,2</td><td>77,2</td><td>91,3</td><td colspan="2">106,2</td><td>122,7</td><td>137,5</td></tr>
<tr><td>28</td><td>1100</td><td>72,0</td><td>86,6</td><td>102,4</td><td colspan="2">119,1</td><td>137,6</td><td>154,3</td></tr>
<tr><td>29</td><td>1600</td><td>82,4</td><td>99,1</td><td>117,2</td><td colspan="2">136,3</td><td>157,5</td><td>176,5</td></tr>
<tr><td>30</td><td>2300</td><td>93,9</td><td>112,9</td><td>133,6</td><td colspan="2">153,4</td><td>179,5</td><td>201,2</td></tr>
<tr><td>31</td><td>3200</td><td>105,7</td><td>127,2</td><td>150,5</td><td colspan="2">174,9</td><td>202,1</td><td>226,6</td></tr>
<tr><td>32</td><td rowspan="6">3200</td><td>550</td><td>70,1</td><td>84,3</td><td>99,8</td><td colspan="2">116,0</td><td>134,0</td><td>150,2</td></tr>
<tr><td>33</td><td>800</td><td>78,0</td><td>93,9</td><td>111,0</td><td colspan="2">129,2</td><td>149,2</td><td>167,0</td></tr>
<tr><td>34</td><td>1100</td><td>87,5</td><td>105,3</td><td>124,6</td><td colspan="2">144,9</td><td>167,4</td><td>187,6</td></tr>
<tr><td>35</td><td>1600</td><td>100,2</td><td>120,5</td><td>142,6</td><td colspan="2">165,8</td><td>191,5</td><td>214,7</td></tr>
<tr><td>36</td><td>2300</td><td>114,1</td><td>137,3</td><td>162,5</td><td colspan="2">188,9</td><td>218,3</td><td>244,7</td></tr>
<tr><td>37</td><td>3200</td><td>128,6</td><td>154,6</td><td>183,0</td><td colspan="2">212,8</td><td>245,8</td><td>275,6</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="16%"><col width="14%"><col width="11%"><col width="11%"><col width="11%"><col width="8%"><col width="3%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="7" rowspan="2">Гибка листов в обечайки конической формы в горячем состоянии в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 28, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Большой диаметр</td><td>Длина обечайки</td><td colspan="7">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">обечайки Д, мм, до</td><td rowspan="2">L, мм, до</td><td>20</td><td>28</td><td>38</td><td colspan="2">50</td><td>65</td><td>80</td></tr>
<tr><td colspan="7">Время Т, чел.-мин.</td></tr>
<tr><td>38</td><td rowspan="7">4000</td><td>550</td><td>79,4</td><td>95,5</td><td>113,0</td><td colspan="2">131,6</td><td>151,8</td><td>170,1</td></tr>
<tr><td>39</td><td>800</td><td>90,8</td><td>109,3</td><td>129,3</td><td colspan="2">150,4</td><td>173,7</td><td>194,7</td></tr>
<tr><td>40</td><td>1100</td><td>101,9</td><td>122,6</td><td>145,0</td><td colspan="2">168,6</td><td>194,8</td><td>218,4</td></tr>
<tr><td>41</td><td>1600</td><td>116,6</td><td>140,3</td><td>166,0</td><td colspan="2">193,0</td><td>223,0</td><td>250,0</td></tr>
<tr><td>42</td><td>2300</td><td>132,8</td><td>159,2</td><td>189,1</td><td colspan="2">220,0</td><td>254,0</td><td>284,8</td></tr>
<tr><td>43</td><td>3200</td><td>149,6</td><td>180,0</td><td>213,0</td><td colspan="2">247,7</td><td>286,1</td><td>320,7</td></tr>
<tr><td>44</td><td>4600</td><td>170,5</td><td>205,2</td><td>242,7</td><td colspan="2">282,2</td><td>326,0</td><td>369,5</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td></tr>
</table>


<a id="p101902"></a>Примечания: 1. При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="7%"><col width="8%"><col width="8%"><col width="11%"><col width="11%"><col width="9%"><col width="8%"><col width="11%"><col width="11%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="3">Угол альфа у основания конической обечайки, град.</td><td colspan="3">Вальцовка обечаек</td></tr>
<tr><td>времени</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>альфа &lt;= 45</td><td>альфа от 45 - 60</td><td>альфа &gt; 60</td><td>из одного листа</td><td>из двух сварных листов</td><td>из трех сварных листов</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,35</td><td>1,2</td><td>1,0</td><td>1,0</td><td>1,15</td><td>1,3</td></tr>
</table>


2. <a id="p101905"></a>Работа выполняется бригадой из двух человек:

                                 0,68    0,36    0,55
<a id="p101906"></a>                   Т = 0,0056 х Д     х L     х h    .


<table>
<colgroup><col width="5%"><col width="11%"><col width="9%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="12" rowspan="2">Гибка листов в полуобечайки цилиндрической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 29, лист 1</td></tr>
<tr><td colspan="16">Содержание работы</td></tr>
<tr><td colspan="16">1. Подать лист и заправить кромку листа в вальцы.</td></tr>
<tr><td colspan="16">2. Вальцевать лист в полуобечайку. (рисунок не</td></tr>
<tr><td colspan="16">3. Проверить полуобечайку по диаметру шаблоном. приводится)</td></tr>
<tr><td colspan="16">4. Снять полуобечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр полуобечайки Д, мм, до</td><td rowspan="2">Длина полуобечайки L,</td><td colspan="13">Толщина листа h, мм, до</td></tr>
<tr><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="5">300</td><td>300</td><td>1,03</td><td>1,20</td><td>1,46</td><td>1,73</td><td>2,14</td><td>2,32</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>400</td><td>1,13</td><td>1,32</td><td>1,64</td><td>1,91</td><td>2,36</td><td>2,56</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>550</td><td>1,26</td><td>1,47</td><td>1,82</td><td>2,12</td><td>2,63</td><td>2,86</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>800</td><td>1,43</td><td>1,67</td><td>2,07</td><td>2,41</td><td>2,99</td><td>3,25</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>1100</td><td>1,60</td><td>1,86</td><td>2,31</td><td>2,69</td><td>3,34</td><td>3,62</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12" rowspan="2">Гибка листов в полуобечайки цилиндрической формы в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 29, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр полуобечайки Д, мм, до</td><td rowspan="2">Длина полуобечайки L,</td><td colspan="12">Толщина листа h, мм, до</td></tr>
<tr><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>мм, до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>6</td><td rowspan="5">400</td><td>300</td><td>1,22</td><td>1,42</td><td>1,76</td><td>2,05</td><td>2,55</td><td>2,76</td><td>3,34</td><td>13,99</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>400</td><td>1,35</td><td>1,57</td><td>1,94</td><td>2,26</td><td>2,81</td><td>3,05</td><td>3,68</td><td>4,40</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>550</td><td>1,50</td><td>1,75</td><td>2,17</td><td>2,52</td><td>3,13</td><td>3,40</td><td>4,11</td><td>4,91</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>800</td><td>1,71</td><td>1,99</td><td>2,46</td><td>2,87</td><td>3,56</td><td>3,86</td><td>4,66</td><td>5,58</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>1100</td><td>1,90</td><td>2,21</td><td>2,74</td><td>3,20</td><td>3,96</td><td>4,30</td><td>5,20</td><td>6,21</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td rowspan="7">550</td><td>400</td><td>1,63</td><td>1,90</td><td>2,35</td><td>2,75</td><td>3,40</td><td>3,69</td><td>4,46</td><td>5,33</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>550</td><td>1,82</td><td>2,12</td><td>2,62</td><td>3,06</td><td>3,79</td><td>4,12</td><td>4,97</td><td>5,94</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>800</td><td>2,06</td><td>2,40</td><td>2,98</td><td>3,47</td><td>4,31</td><td>4,67</td><td>5,65</td><td>6,75</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td>1100</td><td>2,30</td><td>2,68</td><td>3,32</td><td>3,87</td><td>4,80</td><td>5,21</td><td>6,29</td><td>7,52</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>1600</td><td>2,62</td><td>3,05</td><td>3,78</td><td>4,40</td><td>5,46</td><td>5,92</td><td>7,16</td><td>8,58</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>2300</td><td>2,96</td><td>3,44</td><td>4,27</td><td>4,98</td><td>6,17</td><td>6,69</td><td>8,09</td><td>9,67</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td>3200</td><td>3,31</td><td>3,85</td><td>4,78</td><td>5,57</td><td>6,91</td><td>7,49</td><td>9,05</td><td>10,82</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12" rowspan="2">Гибка листов в полуобечайки цилиндрической формы в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 29, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр полуобечайки Д, мм, до</td><td rowspan="2">Длина полуобечайки L,</td><td colspan="12">Толщина листа h, мм, до</td></tr>
<tr><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>мм, до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>18</td><td rowspan="6">750</td><td>550</td><td>2,19</td><td>2,55</td><td>3,16</td><td>3,68</td><td>4,57</td><td>4,96</td><td>5,99</td><td>7,16</td><td>8,42</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td>800</td><td>2,49</td><td>2,90</td><td>3,59</td><td>4,18</td><td>5,19</td><td>5,63</td><td>6,81</td><td>8,13</td><td>9,56</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>1100</td><td>2,77</td><td>3,23</td><td>4,00</td><td>4,66</td><td>5,78</td><td>6,27</td><td>7,58</td><td>9,10</td><td>10,7</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>21</td><td>1600</td><td>3,15</td><td>3,67</td><td>4,55</td><td>5,30</td><td>6,58</td><td>7,14</td><td>8,62</td><td>10,30</td><td>12,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>22</td><td>2300</td><td>3,56</td><td>4,15</td><td>5,15</td><td>5,99</td><td>7,43</td><td>8,06</td><td>9,74</td><td>11,6</td><td>13,7</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>23</td><td>3200</td><td>3,99</td><td>4,64</td><td>5,76</td><td>6,71</td><td>8,32</td><td>9,02</td><td>10,9</td><td>13,0</td><td>15,3</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>24</td><td rowspan="6">1100</td><td>550</td><td>2,60</td><td>3,03</td><td>3,76</td><td>4,38</td><td>5,43</td><td>5,89</td><td>7,12</td><td>8,51</td><td>10,0</td><td>11,6</td><td>13,3</td><td>14,8</td></tr>
<tr><td>25</td><td>800</td><td>2,96</td><td>3,44</td><td>4,27</td><td>4,97</td><td>6,17</td><td>6,69</td><td>8,09</td><td>9,67</td><td>11,4</td><td>13,1</td><td>15,1</td><td>16,2</td></tr>
<tr><td>26</td><td>1100</td><td>3,29</td><td>3,84</td><td>4,76</td><td>5,55</td><td>6,87</td><td>7,46</td><td>9,01</td><td>10,8</td><td>12,7</td><td>14,6</td><td>16,8</td><td>18,8</td></tr>
<tr><td>27</td><td>1600</td><td>3,75</td><td>4,36</td><td>5,41</td><td>6,30</td><td>7,82</td><td>8,48</td><td>10,2</td><td>12,2</td><td>14,4</td><td>16,7</td><td>19,1</td><td>21,4</td></tr>
<tr><td>28</td><td>2300</td><td>4,23</td><td>4,93</td><td>6,12</td><td>7,12</td><td>8,83</td><td>9,58</td><td>11,6</td><td>13,8</td><td>16,3</td><td>18,8</td><td>21,6</td><td>-</td></tr>
<tr><td>29</td><td>3200</td><td>4,74</td><td>5,52</td><td>6,48</td><td>7,97</td><td>9,88</td><td>10,7</td><td>13,0</td><td>15,5</td><td>18,2</td><td>21,0</td><td>24,2</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"></colgroup>
<tr><td colspan="12" rowspan="2">Гибка в вальцах листов в полуобечайки цилиндрической формы</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 29, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр полуобечайки Д, мм, до</td><td rowspan="2">Длина полуобечайки L,</td><td colspan="12">Толщина листа h, мм, до</td></tr>
<tr><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>мм, до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>30</td><td rowspan="6">1400</td><td>550</td><td>3,18</td><td>3,71</td><td>4,60</td><td>5,36</td><td>6,65</td><td>7,21</td><td>8,71</td><td>10,41</td><td>12,24</td><td>14,16</td><td>16,27</td><td>18,2</td></tr>
<tr><td>31</td><td>800</td><td>3,62</td><td>4,21</td><td>5,23</td><td>6,09</td><td>7,55</td><td>8,19</td><td>9,89</td><td>11,83</td><td>13,91</td><td>16,1</td><td>18,5</td><td>20,6</td></tr>
<tr><td>32</td><td>1100</td><td>4,03</td><td>4,70</td><td>5,83</td><td>6,79</td><td>8,41</td><td>9,13</td><td>11,0</td><td>13,2</td><td>15,5</td><td>18,0</td><td>20,6</td><td>23,0</td></tr>
<tr><td>33</td><td>1600</td><td>4,60</td><td>5,40</td><td>6,70</td><td>7,70</td><td>9,60</td><td>10,4</td><td>12,5</td><td>14,9</td><td>17,6</td><td>20,4</td><td>23,4</td><td>26,2</td></tr>
<tr><td>34</td><td>2300</td><td>5,23</td><td>6,0</td><td>7,54</td><td>8,71</td><td>10,8</td><td>11,7</td><td>14,2</td><td>16,9</td><td>19,9</td><td>23,0</td><td>26,5</td><td>-</td></tr>
<tr><td>35</td><td>3200</td><td>5,84</td><td>6,81</td><td>8,43</td><td>9,82</td><td>12,1</td><td>13,1</td><td>15,9</td><td>19,0</td><td>22,3</td><td>24,6</td><td>29,6</td><td>-</td></tr>
<tr><td>36</td><td rowspan="7">1800</td><td>800</td><td>4,24</td><td>4,91</td><td>6,14</td><td>7,13</td><td>8,82</td><td>9,53</td><td>11,5</td><td>13,7</td><td>16,2</td><td>18,7</td><td>21,5</td><td>23,9</td></tr>
<tr><td>37</td><td>1100</td><td>4,71</td><td>5,52</td><td>6,83</td><td>7,94</td><td>9,83</td><td>10,6</td><td>12,8</td><td>15,3</td><td>18,0</td><td>20,8</td><td>23,9</td><td>26,7</td></tr>
<tr><td>38</td><td>1600</td><td>5,34</td><td>6,25</td><td>7,74</td><td>8,92</td><td>11,1</td><td>12,1</td><td>14,6</td><td>17,4</td><td>20,5</td><td>23,7</td><td>27,2</td><td>30,4</td></tr>
<tr><td>39</td><td>2300</td><td>6,0</td><td>7,0</td><td>8,73</td><td>10,1</td><td>12,5</td><td>13,6</td><td>16,5</td><td>19,7</td><td>23,2</td><td>26,8</td><td>30,8</td><td>-</td></tr>
<tr><td>40</td><td>3200</td><td>6,74</td><td>7,81</td><td>9,73</td><td>11,3</td><td>14,1</td><td>15,3</td><td>18,4</td><td>22,0</td><td>25,9</td><td>29,9</td><td>34,4</td><td>-</td></tr>
<tr><td>41</td><td>4600</td><td>7,61</td><td>8,94</td><td>11,0</td><td>12,8</td><td>15,9</td><td>17,3</td><td>20,8</td><td>24,9</td><td>29,3</td><td>33,9</td><td>-</td><td>-</td></tr>
<tr><td>42</td><td>6500</td><td>8,64</td><td>10,0</td><td>12,4</td><td>14,4</td><td>17,9</td><td>19,4</td><td>23,5</td><td>28,0</td><td>32,9</td><td>38,1</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="9%"><col width="7%"><col width="7%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="12" rowspan="2">Гибка листов в полуобечайки цилиндрической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 29, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр полуобечайки Д, мм, до</td><td rowspan="2">Длина полуобечайки L,</td><td colspan="13">Толщина листа h, мм, до</td></tr>
<tr><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>43</td><td rowspan="7">2400</td><td>800</td><td>5,00</td><td>5,83</td><td>7,2</td><td>8,43</td><td>10,3</td><td>11,3</td><td>13,7</td><td>16,3</td><td colspan="2">19,2</td><td>22,2</td><td>25,5</td><td>20,5</td></tr>
<tr><td>44</td><td>1100</td><td>5,61</td><td>6,55</td><td>8,0</td><td>9,4</td><td>11,6</td><td>12,5</td><td>15,2</td><td>18,2</td><td colspan="2">21,4</td><td>24,8</td><td>28,5</td><td>31,0</td></tr>
<tr><td>45</td><td>1600</td><td>6,44</td><td>7,41</td><td>9,2</td><td>10,7</td><td>13,2</td><td>14,3</td><td>17,3</td><td>20,7</td><td colspan="2">24,4</td><td>28,2</td><td>32,4</td><td>36,1</td></tr>
<tr><td>46</td><td>2300</td><td>7,25</td><td>0,31</td><td>10,4</td><td>12,1</td><td>14,9</td><td>16,2</td><td>19,6</td><td>23,4</td><td colspan="2">27,5</td><td>31,8</td><td>36,6</td><td>-</td></tr>
<tr><td>47</td><td>3200</td><td>8,00</td><td>9,35</td><td>11,6</td><td>13,5</td><td>16,7</td><td>18,1</td><td>21,9</td><td>26,2</td><td colspan="2">31,0</td><td>35,6</td><td>40,9</td><td>-</td></tr>
<tr><td>40</td><td>4600</td><td>9,14</td><td>10,50</td><td>13,1</td><td>15,2</td><td>18,9</td><td>20,5</td><td>24,0</td><td>30,0</td><td colspan="2">35,0</td><td>40,3</td><td>-</td><td>-</td></tr>
<tr><td>49</td><td>6500</td><td>10,20</td><td>11,90</td><td>14,7</td><td>17,1</td><td>21,2</td><td>23,1</td><td>27,9</td><td>33,3</td><td colspan="2">38,6</td><td>45,3</td><td>-</td><td>-</td></tr>
<tr><td>50</td><td rowspan="7">3200</td><td>1100</td><td>-</td><td>-</td><td>9,6</td><td>11,1</td><td>13,8</td><td>15,0</td><td>18,1</td><td>21,6</td><td colspan="2">25,6</td><td>29,4</td><td>33,8</td><td>37,7</td></tr>
<tr><td>51</td><td>1600</td><td>-</td><td>-</td><td>11,0</td><td>12,6</td><td>15,7</td><td>17,0</td><td>20,6</td><td>24,6</td><td colspan="2">28,9</td><td>38,5</td><td>38,5</td><td>42,9</td></tr>
<tr><td>52</td><td>2300</td><td>-</td><td>-</td><td>12,3</td><td>14,3</td><td>17,7</td><td>19,3</td><td>23,3</td><td>27,8</td><td colspan="2">32,7</td><td>37,8</td><td>43,5</td><td>-</td></tr>
<tr><td>53</td><td>3200</td><td>-</td><td>-</td><td>13,7</td><td>16,0</td><td>19,8</td><td>21,6</td><td>26,0</td><td>31,1</td><td colspan="2">36,6</td><td>42,3</td><td>48,6</td><td>-</td></tr>
<tr><td>54</td><td>4600</td><td>-</td><td>-</td><td>15,5</td><td>18,1</td><td>22,5</td><td>24,4</td><td>29,4</td><td>35,2</td><td colspan="2">41,4</td><td>47,9</td><td>-</td><td>-</td></tr>
<tr><td>55</td><td>6500</td><td>-</td><td>-</td><td>17,5</td><td>20,4</td><td>25,2</td><td>27,4</td><td>33,1</td><td>39,6</td><td colspan="2">46,5</td><td>53,8</td><td>-</td><td>-</td></tr>
<tr><td>56</td><td>8000</td><td>-</td><td>-</td><td>18,8</td><td>21,9</td><td>27,1</td><td>29,4</td><td>35,5</td><td>42,5</td><td colspan="2">49,9</td><td>57,8</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="9%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12" rowspan="2">Гибка листов в полуобечайки цилиндрической формы в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 29, лист 6</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр полуобечайки Д, мм, до</td><td rowspan="2">Длина полуобечайки L,</td><td colspan="12">Толщина листа h, мм, до</td></tr>
<tr><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>мм, до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>57</td><td rowspan="7">4000</td><td>1100</td><td>7,58</td><td>8,8</td><td>10,9</td><td>12,7</td><td>15,8</td><td>17,1</td><td>20,7</td><td>24,8</td><td>29,1</td><td>33,7</td><td>38,7</td><td>43,2</td></tr>
<tr><td>58</td><td>1600</td><td>8,62</td><td>10,0</td><td>12,4</td><td>14,5</td><td>17,9</td><td>19,5</td><td>23,6</td><td>28,2</td><td>33,1</td><td>38,3</td><td>44,0</td><td>49,1</td></tr>
<tr><td>59</td><td>2300</td><td>9,74</td><td>11,3</td><td>14,1</td><td>16,4</td><td>20,3</td><td>22,0</td><td>26,6</td><td>31,8</td><td>37,4</td><td>43,3</td><td>49,7</td><td>55,5</td></tr>
<tr><td>60</td><td>3200</td><td>10,90</td><td>12,7</td><td>15,7</td><td>18,3</td><td>22,7</td><td>24,7</td><td>29,8</td><td>35,6</td><td>41,9</td><td>48,4</td><td>55,6</td><td>62,1</td></tr>
<tr><td>61</td><td>4600</td><td>12,30</td><td>14,4</td><td>17,8</td><td>20,7</td><td>25,7</td><td>27,9</td><td>33,7</td><td>40,3</td><td>43,4</td><td>54,8</td><td>62,9</td><td>70,3</td></tr>
<tr><td>62</td><td>6500</td><td>13,90</td><td>16,1</td><td>20,0</td><td>23,3</td><td>28,9</td><td>31,4</td><td>37,9</td><td>45,3</td><td>53,3</td><td>61,6</td><td>70,8</td><td>79,0</td></tr>
<tr><td>63</td><td>8000</td><td>14,90</td><td>17,3</td><td>21,5</td><td>25,0</td><td>31,0</td><td>33,7</td><td>40,7</td><td>48,6</td><td>57,2</td><td>66,1</td><td>75,9</td><td>84,8</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>


<a id="p101999"></a>Примечания: 1. Нормативы времени рассчитаны на гибку полуобечаек с предварительно подогнутыми кромками.
2. <a id="p102000"></a>Время на подгибку кромок брать по карте 22 или 23.
3. <a id="p102001"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="13%"><col width="9%"><col width="9%"><col width="6%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="7%"><col width="7%"><col width="9%"><col width="7%"></colgroup>
<tr><td colspan="15">Гибка листов в полуобечайки цилиндрической формы в вальцах Гибка</td></tr>
<tr><td colspan="15">Карта 29, лист 7</td></tr>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td><td colspan="3">Кол-во одновременно сгибаемых полуобечаек</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="3">Вальцовка полуобечаек</td><td colspan="2">Гибка листов в полуобечайки</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>1</td><td>2</td><td>3</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>из одного листа</td><td>из двух сварных листов</td><td>из трех сварных листов</td><td>цилиндрической формы</td><td>эллиптической формы</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,7</td><td>0,55</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,15</td><td>1,3</td><td>1,0</td><td>1,3</td></tr>
</table>


4. <a id="p102005"></a>Работа выполняется бригадой из двух человек:

                                 0,6    0,34    0,53
<a id="p102006"></a>                   Т = 0,0027 х Д    х L     х h    .


<table>
<colgroup><col width="5%"><col width="18%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="11">Гибка листов в полуобечайки цилиндрической формы Гибка в горячем состоянии в вальцах</td></tr>
<tr><td colspan="11">Карта 30, лист 1</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">1. Загрузить лист в нагревательную печь.</td></tr>
<tr><td colspan="11">2. Выгрузить лист из печи и подать к вальцам. (рисунок не</td></tr>
<tr><td colspan="11">3. Заправить кромку листа в вальцы. приводится)</td></tr>
<tr><td colspan="11">4. Вальцевать лист в полуобечайку.</td></tr>
<tr><td colspan="11">5. Проверить полуобечайку по диаметру шаблоном.</td></tr>
<tr><td colspan="11">6. Снять полуобечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр полуобечайки</td><td rowspan="3">Длина полуобечайки L, мм, до</td><td colspan="8">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td><td>105</td><td>130</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="7">550</td><td>400</td><td>5,25</td><td>6,39</td><td>7,6</td><td>8,9</td><td>10,4</td><td>11,7</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>550</td><td>5,97</td><td>7,25</td><td>8,6</td><td>10,1</td><td>11,8</td><td>13,3</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>800</td><td>6,93</td><td>8,43</td><td>10,0</td><td>11,8</td><td>13,7</td><td>15,5</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>1100</td><td>7,87</td><td>9,57</td><td>11,4</td><td>13,4</td><td>15,6</td><td>17,6</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>1600</td><td>9,15</td><td>11,10</td><td>13,3</td><td>15,6</td><td>18,1</td><td>20,4</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>2300</td><td>10,58</td><td>12,90</td><td>15,3</td><td>18,0</td><td>20,9</td><td>23,6</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>3200</td><td>12,10</td><td>14,70</td><td>17,5</td><td>20,5</td><td>23,9</td><td>27,2</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td rowspan="6">750</td><td>550</td><td>7,26</td><td>8,82</td><td>10,5</td><td>12,3</td><td>14,4</td><td>16,2</td><td>18,1</td><td>-</td></tr>
<tr><td>9</td><td>800</td><td>8,43</td><td>10,25</td><td>12,2</td><td>14,3</td><td>16,7</td><td>18,8</td><td>22,1</td><td>-</td></tr>
<tr><td>10</td><td>1100</td><td>9,57</td><td>11,60</td><td>13,9</td><td>16,3</td><td>18,9</td><td>21,4</td><td>25,1</td><td>-</td></tr>
<tr><td>11</td><td>1600</td><td>11,10</td><td>13,50</td><td>16,1</td><td>18,9</td><td>22,0</td><td>24,8</td><td>29,1</td><td>-</td></tr>
<tr><td>12</td><td>2300</td><td>12,90</td><td>15,60</td><td>18,7</td><td>21,9</td><td>25,5</td><td>28,7</td><td>33,0</td><td>-</td></tr>
<tr><td>13</td><td>3200</td><td>14,70</td><td>17,80</td><td>21,3</td><td>24,9</td><td>29,1</td><td>33,0</td><td>38,0</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="18%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="11">Гибка листов в полуобечайки цилиндрической формы Гибка в горячем состоянии в вальцах</td></tr>
<tr><td colspan="11">Карта 30, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр полуобечайки</td><td rowspan="3">Длина полуобечайки L, мм, до</td><td colspan="8">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td><td>105</td><td>130</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>14</td><td rowspan="6">1000</td><td>550</td><td>8,7</td><td>10,5</td><td>12,6</td><td>14,8</td><td>17,2</td><td>19,4</td><td>22,8</td><td>25,8</td></tr>
<tr><td>15</td><td>800</td><td>10,1</td><td>12,3</td><td>14,7</td><td>17,2</td><td>20,0</td><td>22,6</td><td>26,4</td><td>29,9</td></tr>
<tr><td>16</td><td>1100</td><td>11,4</td><td>13,9</td><td>16,6</td><td>19,5</td><td>22,7</td><td>25,6</td><td>30,0</td><td>34,0</td></tr>
<tr><td>17</td><td>1600</td><td>13,3</td><td>16,2</td><td>19,3</td><td>22,7</td><td>26,4</td><td>29,8</td><td>35,0</td><td>39,0</td></tr>
<tr><td>18</td><td>2300</td><td>15,4</td><td>18,7</td><td>22,4</td><td>26,2</td><td>30,5</td><td>34,0</td><td>40,0</td><td>-</td></tr>
<tr><td>19</td><td>3200</td><td>17,6</td><td>21,4</td><td>25,5</td><td>29,9</td><td>35,0</td><td>39,0</td><td>46,0</td><td>-</td></tr>
<tr><td>20</td><td rowspan="6">1350</td><td>550</td><td>10,5</td><td>12,8</td><td>15,2</td><td>17,9</td><td>20,8</td><td>23,5</td><td>27,5</td><td>31,1</td></tr>
<tr><td>21</td><td>800</td><td>12,2</td><td>14,8</td><td>17,7</td><td>20,8</td><td>24,2</td><td>27,3</td><td>32,0</td><td>36,0</td></tr>
<tr><td>22</td><td>1100</td><td>13,9</td><td>16,8</td><td>20,1</td><td>23,6</td><td>27,5</td><td>31,0</td><td>36,0</td><td>41,0</td></tr>
<tr><td>23</td><td>1600</td><td>16,1</td><td>19,6</td><td>23,4</td><td>27,4</td><td>31,9</td><td>36,0</td><td>42,0</td><td>48,0</td></tr>
<tr><td>24</td><td>2300</td><td>18,6</td><td>22,6</td><td>27,0</td><td>32,0</td><td>37,0</td><td>42,0</td><td>49,0</td><td>-</td></tr>
<tr><td>25</td><td>3200</td><td>21,2</td><td>25,8</td><td>31,0</td><td>36,0</td><td>42,0</td><td>47,0</td><td>56,0</td><td>-</td></tr>
<tr><td>26</td><td rowspan="7">1800</td><td>800</td><td>14,6</td><td>17,8</td><td>21,2</td><td>24,9</td><td>28,9</td><td>33,0</td><td>38,0</td><td>43,0</td></tr>
<tr><td>27</td><td>1100</td><td>16,6</td><td>20,2</td><td>24,1</td><td>28,3</td><td>33,0</td><td>37,0</td><td>43,0</td><td>49,0</td></tr>
<tr><td>28</td><td>1600</td><td>19,3</td><td>23,5</td><td>28,0</td><td>33,0</td><td>38,0</td><td>43,0</td><td>51,0</td><td>57,0</td></tr>
<tr><td>29</td><td>2300</td><td>22,3</td><td>27,1</td><td>32,0</td><td>38,0</td><td>44,0</td><td>49,0</td><td>58,0</td><td>-</td></tr>
<tr><td>30</td><td>3200</td><td>25,5</td><td>31,0</td><td>37,0</td><td>43,0</td><td>50,0</td><td>57,0</td><td>67,0</td><td>-</td></tr>
<tr><td>31</td><td>4600</td><td>29,5</td><td>36,0</td><td>43,0</td><td>50,0</td><td>58,0</td><td>66,0</td><td>-</td><td>-</td></tr>
<tr><td>32</td><td>6500</td><td>34,0</td><td>41,0</td><td>49,0</td><td>57,0</td><td>67,0</td><td>76,0</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="18%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="11">Гибка в вальцах листов в полуобечайки цилиндрической Гибка формы в горячем состоянии</td></tr>
<tr><td colspan="11">Карта 30, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр полуобечайки</td><td rowspan="3">Длина полуобечайки L, мм, до</td><td colspan="8">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>20</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td><td>105</td><td>130</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>33</td><td rowspan="7">2400</td><td>800</td><td>17,5</td><td>21</td><td>25</td><td>29</td><td>35</td><td>39</td><td>46</td><td>51</td></tr>
<tr><td>34</td><td>1100</td><td>19,9</td><td>24</td><td>28</td><td>34</td><td>39</td><td>44</td><td>52</td><td>59</td></tr>
<tr><td>35</td><td>1600</td><td>23,1</td><td>28</td><td>34</td><td>39</td><td>46</td><td>52</td><td>61</td><td>68</td></tr>
<tr><td>36</td><td>2300</td><td>26,8</td><td>32</td><td>39</td><td>45</td><td>53</td><td>60</td><td>70</td><td>79</td></tr>
<tr><td>37</td><td>3200</td><td>30,0</td><td>37</td><td>44</td><td>55</td><td>61</td><td>68</td><td>80</td><td>-</td></tr>
<tr><td>38</td><td>4600</td><td>35,0</td><td>43</td><td>51</td><td>61</td><td>70</td><td>79</td><td>-</td><td>-</td></tr>
<tr><td>39</td><td>6500</td><td>41,0</td><td>49</td><td>59</td><td>69</td><td>80</td><td>91</td><td>-</td><td>-</td></tr>
<tr><td>40</td><td rowspan="7">3200</td><td>1100</td><td>24,1</td><td>29</td><td>34</td><td>41</td><td>47</td><td>53</td><td>62</td><td>71</td></tr>
<tr><td>41</td><td>1600</td><td>27,7</td><td>34</td><td>40</td><td>47</td><td>55</td><td>62</td><td>72</td><td>-</td></tr>
<tr><td>42</td><td>2300</td><td>32,0</td><td>39</td><td>46</td><td>55</td><td>63</td><td>72</td><td>83</td><td>-</td></tr>
<tr><td>43</td><td>3200</td><td>37,0</td><td>44</td><td>53</td><td>62</td><td>72</td><td>82</td><td>96</td><td>-</td></tr>
<tr><td>44</td><td>4600</td><td>42,0</td><td>51</td><td>61</td><td>72</td><td>84</td><td>95</td><td>-</td><td>-</td></tr>
<tr><td>45</td><td>6500</td><td>40,0</td><td>59</td><td>70</td><td>83</td><td>96</td><td>109</td><td>-</td><td>-</td></tr>
<tr><td>46</td><td>8000</td><td>52,0</td><td>64</td><td>77</td><td>105</td><td>118</td><td>138</td><td>-</td><td>-</td></tr>
<tr><td>47</td><td rowspan="7">4000</td><td>1100</td><td>27,5</td><td>33</td><td>40</td><td>47</td><td>54</td><td>61</td><td>72</td><td>-</td></tr>
<tr><td>48</td><td>1600</td><td>32,0</td><td>39</td><td>46</td><td>54</td><td>63</td><td>71</td><td>83</td><td>-</td></tr>
<tr><td>49</td><td>2300</td><td>37,0</td><td>45</td><td>54</td><td>63</td><td>73</td><td>82</td><td>96</td><td>-</td></tr>
<tr><td>50</td><td>3200</td><td>42,0</td><td>51</td><td>61</td><td>72</td><td>83</td><td>94</td><td>110</td><td>-</td></tr>
<tr><td>51</td><td>4600</td><td>49,0</td><td>59</td><td>70</td><td>83</td><td>96</td><td>109</td><td>-</td><td>-</td></tr>
<tr><td>52</td><td>6500</td><td>56,0</td><td>68</td><td>81</td><td>95</td><td>111</td><td>125</td><td>-</td><td>-</td></tr>
<tr><td>53</td><td>8000</td><td>61,0</td><td>74</td><td>88</td><td>103</td><td>120</td><td>136</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="76%"><col width="24%"></colgroup>
<tr><td rowspan="2">Гибка листов в полуобечайки цилиндрической формы в горячем состоянии в вальцах</td><td>Гибка</td></tr>
<tr><td>Карта 30, лист 4</td></tr>
</table>


<a id="p102083"></a>Примечания: 1. При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="20%"><col width="8%"><col width="8%"><col width="8%"><col width="9%"><col width="11%"><col width="11%"><col width="12%"><col width="12%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="3">Вальцовка полуобечаек</td><td colspan="2">Гибка листов в полуобечайки</td></tr>
<tr><td>нормы времени</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>из одного листа</td><td>из двух сварных листов</td><td>из трех сварных листов</td><td>цилиндрической формы</td><td>эллиптической формы</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,15</td><td>1,3</td><td>1,0</td><td>1,3</td></tr>
</table>


2. <a id="p102086"></a>Работа выполняется бригадой из двух человек:

                                   0,63    0,4    0,58
<a id="p102087"></a>                    Т = 0,00158 х Д     х L    х h    .


<table>
<colgroup><col width="5%"><col width="12%"><col width="11%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"><col width="8%"><col width="7%"></colgroup>
<tr><td colspan="13">Гибка листов в полуобечайки конической формы в вальцах Гибка</td></tr>
<tr><td colspan="13">Карта 31, лист 1</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">1. Подать лист к вальцам.</td></tr>
<tr><td colspan="13">2. Заправить кромку листа в вальцы. (рисунок не</td></tr>
<tr><td colspan="13">3. Вальцевать лист в полуобечайку. приводится)</td></tr>
<tr><td colspan="13">4. Проверить полуобечайку по диаметрам шаблонами.</td></tr>
<tr><td colspan="13">5. Снять полуобечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Большой диаметр</td><td rowspan="2">Длина полуобечайки L,</td><td colspan="10">Толщина листа h, мм, до</td></tr>
<tr><td>полуобечайки Д,</td><td>2</td><td>3</td><td>4</td><td>5</td><td>6</td><td>12</td><td>14</td><td>20</td><td>28</td><td>38</td></tr>
<tr><td>мм, до</td><td>мм, до</td><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="5">300</td><td>300</td><td>1,8</td><td>2,2</td><td>2,5</td><td>2,8</td><td>3,5</td><td>4,3</td><td>4,6</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>400</td><td>1,9</td><td>2,4</td><td>2,8</td><td>3,1</td><td>3,9</td><td>4,7</td><td>5,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>550</td><td>2,2</td><td>2,7</td><td>3,1</td><td>3,5</td><td>4,3</td><td>5,1</td><td>5,7</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>800</td><td>2,5</td><td>3,1</td><td>3,5</td><td>3,9</td><td>4,9</td><td>6,0</td><td>6,5</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>1100</td><td>2,8</td><td>3,4</td><td>3,9</td><td>4,4</td><td>5,5</td><td>6,7</td><td>7,2</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td rowspan="5">400</td><td>300</td><td>2,1</td><td>2,6</td><td>3,0</td><td>3,3</td><td>4,2</td><td>5,1</td><td>5,5</td><td>6,6</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>400</td><td>2,3</td><td>2,9</td><td>3,3</td><td>3,7</td><td>4,6</td><td>5,6</td><td>6,1</td><td>7,3</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>550</td><td>2,6</td><td>3,2</td><td>3,7</td><td>4,1</td><td>5,2</td><td>6,3</td><td>6,8</td><td>8,1</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>800</td><td>3,0</td><td>3,6</td><td>4,2</td><td>4,6</td><td>5,8</td><td>7,2</td><td>7,7</td><td>9,2</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>1100</td><td>3,3</td><td>4,0</td><td>4,6</td><td>5,2</td><td>6,5</td><td>7,9</td><td>8,6</td><td>10,2</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td rowspan="5">550</td><td>400</td><td>2,9</td><td>3,5</td><td>4,1</td><td>4,5</td><td>5,7</td><td>6,9</td><td>7,9</td><td>8,9</td><td>10,5</td><td>-</td></tr>
<tr><td>12</td><td>550</td><td>3,2</td><td>3,8</td><td>4,4</td><td>4,9</td><td>6,2</td><td>7,6</td><td>8,2</td><td>8,8</td><td>11,6</td><td>-</td></tr>
<tr><td>13</td><td>800</td><td>3,6</td><td>4,4</td><td>5,1</td><td>5,6</td><td>7,1</td><td>8,6</td><td>9,3</td><td>11,1</td><td>13,1</td><td>-</td></tr>
<tr><td>14</td><td>1100</td><td>4,0</td><td>4,9</td><td>5,6</td><td>6,3</td><td>7,9</td><td>9,6</td><td>10,4</td><td>12,4</td><td>14,6</td><td>-</td></tr>
<tr><td>15</td><td>1600</td><td>4,5</td><td>5,5</td><td>6,4</td><td>7,1</td><td>9,0</td><td>10,9</td><td>11,8</td><td>14,1</td><td>16,6</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="11%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="5%"><col width="3%"><col width="7%"><col width="8%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="2">Гибка листов в полуобечайки конической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 31, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Большой диаметр</td><td rowspan="2">Длина полуобечайки L,</td><td colspan="11">Толщина листа h, мм, до</td></tr>
<tr><td>полуобечайки Д,</td><td>2</td><td>3</td><td>4</td><td>5</td><td>8</td><td>12</td><td colspan="2">14</td><td>20</td><td>28</td><td>38</td></tr>
<tr><td>мм, до</td><td>мм, до</td><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>16</td><td rowspan="5">750</td><td>550</td><td>3,8</td><td>4,6</td><td>5,4</td><td>5,9</td><td>7,5</td><td>9,2</td><td colspan="2">9,9</td><td>11,8</td><td>13,9</td><td>16,2</td></tr>
<tr><td>17</td><td>800</td><td>4,3</td><td>5,2</td><td>6,1</td><td>6,8</td><td>8,6</td><td>10,4</td><td colspan="2">11,3</td><td>13,4</td><td>15,8</td><td>18,4</td></tr>
<tr><td>18</td><td>1100</td><td>4,8</td><td>5,9</td><td>6,8</td><td>7,6</td><td>9,5</td><td>11,6</td><td colspan="2">12,5</td><td>14,9</td><td>17,6</td><td>20,5</td></tr>
<tr><td>19</td><td>1600</td><td>5,5</td><td>6,7</td><td>7,7</td><td>8,6</td><td>10,8</td><td>13,2</td><td colspan="2">14,2</td><td>16,9</td><td>20,0</td><td>23,3</td></tr>
<tr><td>20</td><td>2300</td><td>6,2</td><td>7,6</td><td>8,7</td><td>9,7</td><td>12,2</td><td>14,9</td><td colspan="2">16,1</td><td>19,2</td><td>22,6</td><td>26,3</td></tr>
<tr><td>21</td><td rowspan="5">1000</td><td>550</td><td>-</td><td>5,5</td><td>6,4</td><td>7,1</td><td>8,9</td><td>10,9</td><td colspan="2">11,8</td><td>14,0</td><td>16,5</td><td>19,2</td></tr>
<tr><td>22</td><td>800</td><td>-</td><td>6,3</td><td>7,2</td><td>8,1</td><td>10,2</td><td>12,4</td><td colspan="2">13,3</td><td>15,9</td><td>18,8</td><td>21,8</td></tr>
<tr><td>23</td><td>1100</td><td>-</td><td>7,0</td><td>8,1</td><td>9,0</td><td>11,3</td><td>13,8</td><td colspan="2">14,9</td><td>17,8</td><td>21,0</td><td>24,3</td></tr>
<tr><td>24</td><td>1600</td><td>-</td><td>7,9</td><td>9,1</td><td>10,2</td><td>12,9</td><td>15,7</td><td colspan="2">16,9</td><td>20,2</td><td>23,8</td><td>27,6</td></tr>
<tr><td>25</td><td>2300</td><td>-</td><td>9,0</td><td>10,4</td><td>11,6</td><td>14,6</td><td>17,8</td><td colspan="2">19,1</td><td>22,8</td><td>26,9</td><td>31,2</td></tr>
<tr><td>26</td><td rowspan="5">1350</td><td>550</td><td>-</td><td>6,6</td><td>7,6</td><td>8,5</td><td>10,7</td><td>13,1</td><td colspan="2">14,1</td><td>16,8</td><td>19,8</td><td>23,0</td></tr>
<tr><td>27</td><td>800</td><td>-</td><td>7,5</td><td>8,6</td><td>9,6</td><td>12,1</td><td>14,8</td><td colspan="2">16,0</td><td>19,1</td><td>22,5</td><td>26,1</td></tr>
<tr><td>28</td><td>1100</td><td>-</td><td>8,4</td><td>9,6</td><td>10,7</td><td>13,6</td><td>16,5</td><td colspan="2">17,8</td><td>21,2</td><td>25,1</td><td>29,1</td></tr>
<tr><td>29</td><td>1600</td><td>-</td><td>9,5</td><td>10,9</td><td>12,2</td><td>15,4</td><td>18,8</td><td colspan="2">20,3</td><td>24,2</td><td>28,5</td><td>33,1</td></tr>
<tr><td>30</td><td>2300</td><td>-</td><td>10,8</td><td>12,4</td><td>13,8</td><td>14,7</td><td>21,2</td><td colspan="2">22,9</td><td>27,3</td><td>32,2</td><td>37,4</td></tr>
<tr><td>31</td><td rowspan="5">1800</td><td>550</td><td>-</td><td>-</td><td>9,1</td><td>10,1</td><td>12,7</td><td>15,5</td><td colspan="2">16,7</td><td>19,9</td><td>23,5</td><td>27,3</td></tr>
<tr><td>32</td><td>800</td><td>-</td><td>-</td><td>10,3</td><td>11,5</td><td>14,5</td><td>17,6</td><td colspan="2">19,0</td><td>22,7</td><td>26,7</td><td>31,0</td></tr>
<tr><td>33</td><td>1100</td><td>-</td><td>-</td><td>11,5</td><td>12,8</td><td>16,1</td><td>19,7</td><td colspan="2">21,2</td><td>25,2</td><td>29,8</td><td>34,6</td></tr>
<tr><td>34</td><td>1600</td><td>-</td><td>-</td><td>13,0</td><td>14,5</td><td>18,3</td><td>22,3</td><td colspan="2">24,1</td><td>28,7</td><td>33,8</td><td>39,3</td></tr>
<tr><td>35</td><td>2300</td><td>-</td><td>-</td><td>14,7</td><td>16,5</td><td>20,7</td><td>25,3</td><td colspan="2">27,2</td><td>32,3</td><td>38,3</td><td>44,5</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="11%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="8%"><col width="4%"><col width="3%"><col width="8%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="2">Гибка листов в полуобечайки конической формы в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 31, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Большой диаметр</td><td rowspan="2">Длина полуобечайки L,</td><td colspan="11">Толщина листа h, мм, до</td></tr>
<tr><td>полуобечайки Д,</td><td>2</td><td>3</td><td>4</td><td>5</td><td>6</td><td>12</td><td colspan="2">14</td><td>20</td><td>28</td><td>38</td></tr>
<tr><td>мм, до</td><td>мм, до</td><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>36</td><td rowspan="6">2400</td><td>550</td><td>-</td><td>-</td><td>10,8</td><td>12,0</td><td>15,1</td><td>18,5</td><td colspan="2">19,9</td><td>23,7</td><td>28,0</td><td>32,5</td></tr>
<tr><td>37</td><td>800</td><td>-</td><td>-</td><td>13,2</td><td>13,6</td><td>17,2</td><td>20,9</td><td colspan="2">22,6</td><td>26,9</td><td>31,8</td><td>36,9</td></tr>
<tr><td>38</td><td>1100</td><td>-</td><td>-</td><td>13,6</td><td>15,2</td><td>19,2</td><td>23,4</td><td colspan="2">25,2</td><td>30,0</td><td>35,4</td><td>41,1</td></tr>
<tr><td>39</td><td>1600</td><td>-</td><td>-</td><td>15,5</td><td>17,3</td><td>21,8</td><td>26,5</td><td colspan="2">28,6</td><td>34,1</td><td>40,2</td><td>46,7</td></tr>
<tr><td>40</td><td>2300</td><td>-</td><td>-</td><td>17,5</td><td>19,5</td><td>24,6</td><td>30,0</td><td colspan="2">32,4</td><td>38,6</td><td>45,5</td><td>52,9</td></tr>
<tr><td>41</td><td>3200</td><td>-</td><td>-</td><td>19,6</td><td>21,9</td><td>27,5</td><td>33,6</td><td colspan="2">36,2</td><td>43,2</td><td>50,9</td><td>59,2</td></tr>
<tr><td>42</td><td rowspan="6">3200</td><td>550</td><td>-</td><td>-</td><td>-</td><td>14,3</td><td>18,0</td><td>21,9</td><td colspan="2">23,7</td><td>28,2</td><td>33,2</td><td>38,6</td></tr>
<tr><td>43</td><td>800</td><td>-</td><td>-</td><td>-</td><td>16,2</td><td>20,4</td><td>24,9</td><td colspan="2">26,9</td><td>32,0</td><td>37,8</td><td>43,9</td></tr>
<tr><td>44</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>18,1</td><td>22,8</td><td>27,8</td><td colspan="2">29,9</td><td>35,7</td><td>42,1</td><td>48,9</td></tr>
<tr><td>45</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>20,5</td><td>25,9</td><td>31,6</td><td colspan="2">34,0</td><td>40,5</td><td>47,8</td><td>55,5</td></tr>
<tr><td>45</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>23,3</td><td>29,3</td><td>35,7</td><td colspan="2">38,6</td><td>45,9</td><td>54,2</td><td>62,9</td></tr>
<tr><td>47</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>26,0</td><td>32,7</td><td>39,9</td><td colspan="2">43,1</td><td>51,3</td><td>60,5</td><td>70,3</td></tr>
<tr><td>48</td><td rowspan="7">4000</td><td>550</td><td>-</td><td>-</td><td>-</td><td>16,3</td><td>20,5</td><td>25,1</td><td colspan="2">27,0</td><td>32,3</td><td>38,0</td><td>44,1</td></tr>
<tr><td>49</td><td>800</td><td>-</td><td>-</td><td>-</td><td>18,5</td><td>23,3</td><td>28,5</td><td colspan="2">30,7</td><td>36,6</td><td>43,2</td><td>50,1</td></tr>
<tr><td>50</td><td>1100</td><td>-</td><td>-</td><td>-</td><td>20,7</td><td>26,0</td><td>31,7</td><td colspan="2">34,2</td><td>40,8</td><td>48,1</td><td>55,9</td></tr>
<tr><td>51</td><td>1600</td><td>-</td><td>-</td><td>-</td><td>23,5</td><td>29,6</td><td>36,1</td><td colspan="2">38,9</td><td>46,3</td><td>54,7</td><td>63,5</td></tr>
<tr><td>52</td><td>2300</td><td>-</td><td>-</td><td>-</td><td>26,6</td><td>33,5</td><td>40,8</td><td colspan="2">44,0</td><td>52,4</td><td>61,8</td><td>71,8</td></tr>
<tr><td>53</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>29,7</td><td>37,4</td><td>45,7</td><td colspan="2">49,3</td><td>58,7</td><td>69,2</td><td>80,3</td></tr>
<tr><td>54</td><td>4600</td><td>-</td><td>-</td><td>-</td><td>33,6</td><td>42,3</td><td>51,7</td><td colspan="2">55,7</td><td>66,4</td><td>78,3</td><td>90,9</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="76%"><col width="24%"></colgroup>
<tr><td rowspan="2">Гибка листов в полуобечайки конической формы в вальцах</td><td>Гибка</td></tr>
<tr><td>Карта 31, лист 4</td></tr>
</table>


<a id="p102162"></a>Примечания: 1. Нормативы времени рассчитаны на гибку полуобечаек с предварительно подогнутыми кромками.
2. <a id="p102163"></a>Время на подгибку кромок брать по карте 22 или 23.
3. <a id="p102164"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="14%"><col width="8%"><col width="8%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="10%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="3">Угол альфа у основания конической полуобечайки, град.</td><td colspan="3">Гибка полуобечаек</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>альфа &lt;= 45</td><td>альфа от 45 - 60</td><td>альфа &gt; 60</td><td>из одного листа</td><td>из двух сварных листов</td><td>из трех сварных листов</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,35</td><td>1,2</td><td>1,0</td><td>1,0</td><td>1,15</td><td>1,3</td></tr>
</table>


4. <a id="p102167"></a>Работа выполняется бригадой из двух человек:

                                0,6    0,34    0,49
<a id="p102168"></a>                   Т = 0,006 х Д    х L     х h    .


<table>
<colgroup><col width="5%"><col width="18%"><col width="12%"><col width="11%"><col width="11%"><col width="11%"><col width="8%"><col width="3%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="7" rowspan="2">Гибка листов в полуобечайки конической формы в горячем состоянии в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 32, лист 1</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Загрузить лист в нагревательную печь.</td></tr>
<tr><td colspan="10">2. Выгрузить лист из печи и подать к вальцам. (рисунок не</td></tr>
<tr><td colspan="10">3. Заправить кромку листа в вальцы. приводится)</td></tr>
<tr><td colspan="10">4. Вальцевать лист в полуобечайку.</td></tr>
<tr><td colspan="10">5. Проверить полуобечайку по диаметрам шаблонами.</td></tr>
<tr><td colspan="10">6. Снять полуобечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Большой диаметр</td><td rowspan="3">Длина полуобечайки L, мм, до</td><td colspan="7">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">полуобечайки Д, мм, до</td><td>20</td><td>28</td><td>38</td><td colspan="2">50</td><td>65</td><td>80</td></tr>
<tr><td colspan="7">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">500</td><td>550</td><td>12,1</td><td>14,8</td><td>17,8</td><td colspan="2">20,9</td><td>24,6</td><td>27,8</td></tr>
<tr><td>2</td><td>800</td><td>13,9</td><td>17,1</td><td>20,5</td><td colspan="2">24,2</td><td>28,3</td><td>32,1</td></tr>
<tr><td>3</td><td>1100</td><td>15,7</td><td>19,3</td><td>23,2</td><td colspan="2">27,3</td><td>31,9</td><td>36,2</td></tr>
<tr><td>4</td><td>1600</td><td>18,2</td><td>22,2</td><td>26,7</td><td colspan="2">31,5</td><td>36,9</td><td>41,7</td></tr>
<tr><td>5</td><td rowspan="5">750</td><td>550</td><td>14,9</td><td>18,3</td><td>22,1</td><td colspan="2">25,9</td><td>30,3</td><td>34,3</td></tr>
<tr><td>6</td><td>800</td><td>17,2</td><td>21,1</td><td>25,3</td><td colspan="2">29,9</td><td>35,1</td><td>39,6</td></tr>
<tr><td>7</td><td>1100</td><td>19,5</td><td>23,8</td><td>28,6</td><td colspan="2">33,7</td><td>39,5</td><td>44,7</td></tr>
<tr><td>8</td><td>1600</td><td>22,4</td><td>27,5</td><td>33,1</td><td colspan="2">38,9</td><td>45,5</td><td>51,6</td></tr>
<tr><td>9</td><td>2300</td><td>25,8</td><td>31,5</td><td>37,9</td><td colspan="2">44,6</td><td>52,3</td><td>59,2</td></tr>
<tr><td>10</td><td rowspan="5">1000</td><td>550</td><td>18,2</td><td>22,3</td><td>26,7</td><td colspan="2">31,5</td><td>36,9</td><td>41,8</td></tr>
<tr><td>11</td><td>800</td><td>20,9</td><td>25,7</td><td>22,0</td><td colspan="2">36,3</td><td>42,5</td><td>48,2</td></tr>
<tr><td>12</td><td>1100</td><td>23,8</td><td>29,0</td><td>34,8</td><td colspan="2">41,0</td><td>48,0</td><td>54,0</td></tr>
<tr><td>13</td><td>1600</td><td>27,3</td><td>33,4</td><td>40,1</td><td colspan="2">47,3</td><td>55,0</td><td>62,0</td></tr>
<tr><td>14</td><td>2300</td><td>31,3</td><td>38,3</td><td>46,0</td><td colspan="2">54,0</td><td>63,0</td><td>72,0</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="18%"><col width="12%"><col width="11%"><col width="11%"><col width="11%"><col width="8%"><col width="3%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="7" rowspan="2">Гибка листов в полуобечайки конической формы в горячем состоянии в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 32, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Большой диаметр</td><td rowspan="3">Длина полуобечайки L, мм, до</td><td colspan="7">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">полуобечайки Д, мм, до</td><td>20</td><td>28</td><td>38</td><td colspan="2">50</td><td>65</td><td>80</td></tr>
<tr><td colspan="7">Время Т, чел.-мин.</td></tr>
<tr><td>15</td><td rowspan="5">1400</td><td>550</td><td>22,9</td><td>28,0</td><td>33</td><td colspan="2">39</td><td>46</td><td>52</td></tr>
<tr><td>16</td><td>800</td><td>26,4</td><td>32,3</td><td>38</td><td colspan="2">45</td><td>53</td><td>61</td></tr>
<tr><td>17</td><td>1100</td><td>29,8</td><td>36,4</td><td>43</td><td colspan="2">52</td><td>60</td><td>68</td></tr>
<tr><td>18</td><td>1600</td><td>34,3</td><td>41,9</td><td>50</td><td colspan="2">60</td><td>70</td><td>79</td></tr>
<tr><td>19</td><td>2300</td><td>39,4</td><td>48,2</td><td>58</td><td colspan="2">68</td><td>80</td><td>90</td></tr>
<tr><td>20</td><td rowspan="5">1800</td><td>550</td><td>27,1</td><td>33,2</td><td>40</td><td colspan="2">47</td><td>55</td><td>62</td></tr>
<tr><td>21</td><td>800</td><td>31,3</td><td>38,3</td><td>46</td><td colspan="2">54</td><td>63</td><td>72</td></tr>
<tr><td>22</td><td>1100</td><td>35,3</td><td>43,2</td><td>52</td><td colspan="2">61</td><td>72</td><td>81</td></tr>
<tr><td>23</td><td>1600</td><td>40,7</td><td>50,0</td><td>60</td><td colspan="2">70</td><td>86</td><td>93</td></tr>
<tr><td>24</td><td>2300</td><td>46,7</td><td>57,0</td><td>69</td><td colspan="2">81</td><td>95</td><td>107</td></tr>
<tr><td>25</td><td rowspan="6">2400</td><td>550</td><td>32,9</td><td>40,4</td><td>48</td><td colspan="2">57</td><td>67</td><td>76</td></tr>
<tr><td>26</td><td>800</td><td>38,0</td><td>46,5</td><td>56</td><td colspan="2">66</td><td>77</td><td>87</td></tr>
<tr><td>27</td><td>1100</td><td>42,9</td><td>53,0</td><td>63</td><td colspan="2">74</td><td>87</td><td>99</td></tr>
<tr><td>28</td><td>1600</td><td>49,0</td><td>61,0</td><td>73</td><td colspan="2">86</td><td>100</td><td>114</td></tr>
<tr><td>29</td><td>2300</td><td>57,0</td><td>69,0</td><td>83</td><td colspan="2">98</td><td>115</td><td>130</td></tr>
<tr><td>30</td><td>3200</td><td>64,0</td><td>79,0</td><td>95</td><td colspan="2">112</td><td>131</td><td>148</td></tr>
<tr><td>31</td><td rowspan="6">3200</td><td>550</td><td>40,1</td><td>49,1</td><td>59</td><td colspan="2">69</td><td>81</td><td>92</td></tr>
<tr><td>32</td><td>800</td><td>46,3</td><td>57,0</td><td>68</td><td colspan="2">80</td><td>94</td><td>106</td></tr>
<tr><td>33</td><td>1100</td><td>52,0</td><td>64,0</td><td>77</td><td colspan="2">90</td><td>106</td><td>120</td></tr>
<tr><td>34</td><td>1600</td><td>60,0</td><td>74,0</td><td>88</td><td colspan="2">104</td><td>122</td><td>138</td></tr>
<tr><td>35</td><td>2300</td><td>69,0</td><td>85,0</td><td>102</td><td colspan="2">120</td><td>140</td><td>159</td></tr>
<tr><td>36</td><td>3200</td><td>78,0</td><td>96,0</td><td>115</td><td colspan="2">136</td><td>159</td><td>180</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="18%"><col width="12%"><col width="11%"><col width="11%"><col width="11%"><col width="8%"><col width="3%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="7" rowspan="2">Гибка листов в полуобечайки конической формы в горячем состоянии в вальцах</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 32, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Большой диаметр</td><td rowspan="3">Длина полуобечайки L, мм, до</td><td colspan="7">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">полуобечайки Д, мм, до</td><td>20</td><td>28</td><td>38</td><td colspan="2">50</td><td>65</td><td>80</td></tr>
<tr><td colspan="7">Время Т, чел.-мин.</td></tr>
<tr><td>37</td><td rowspan="7">4000</td><td>550</td><td>46</td><td>57</td><td>68</td><td colspan="2">81</td><td>95</td><td>107</td></tr>
<tr><td>38</td><td>800</td><td>53</td><td>65</td><td>79</td><td colspan="2">93</td><td>109</td><td>123</td></tr>
<tr><td>39</td><td>1100</td><td>54</td><td>74</td><td>89</td><td colspan="2">105</td><td>123</td><td>139</td></tr>
<tr><td>40</td><td>1600</td><td>70</td><td>85</td><td>103</td><td colspan="2">121</td><td>142</td><td>161</td></tr>
<tr><td>41</td><td>2300</td><td>80</td><td>98</td><td>118</td><td colspan="2">139</td><td>163</td><td>185</td></tr>
<tr><td>42</td><td>3200</td><td>91</td><td>111</td><td>134</td><td colspan="2">158</td><td>185</td><td>209</td></tr>
<tr><td>43</td><td>4600</td><td>104</td><td>128</td><td>154</td><td colspan="2">181</td><td>212</td><td>240</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td></tr>
</table>


<a id="p102231"></a>Примечания: 1. При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="14%"><col width="6%"><col width="7%"><col width="7%"><col width="9%"><col width="9%"><col width="8%"><col width="7%"><col width="9%"><col width="9%"><col width="8%"><col width="8%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="3">Скорость вращения валков, м/мин.</td><td colspan="3">Угол альфа у основания конической полуобечайки, град.</td><td colspan="3">Гибка полуобечайки</td><td colspan="2">Материал</td></tr>
<tr><td>времени</td><td>до 6</td><td>7 - 8</td><td>св. 8</td><td>альфа &lt;= 45</td><td>альфа от 45 - 60</td><td>альфа &gt; 60</td><td>из одного листа</td><td>из двух сварных листов</td><td>из трех сварных листов</td><td>углеродистая сталь</td><td>легированная сталь</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,9</td><td>1,35</td><td>1,2</td><td>1,0</td><td>1,0</td><td>1,15</td><td>1,3</td><td>1,0</td><td>1,2</td></tr>
</table>


2. <a id="p102234"></a>Работа выполняется бригадой из двух человек:

                                 0,68    0,38    0,6
<a id="p102235"></a>                   Т = 0,0025 х Д     х L     х h   .


<table>
<colgroup><col width="5%"><col width="18%"><col width="11%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="4%"><col width="5%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="8" rowspan="2">Гибка толстостенных полуобечаек в горячем состоянии на прессе</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 33, лист 1</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">1. Загрузить лист в нагревательную печь.</td></tr>
<tr><td colspan="11">2. Выгрузить лист из печи, подать к прессу. (рисунок не</td></tr>
<tr><td colspan="11">3. Установить лист на пресс. приводится)</td></tr>
<tr><td colspan="11">4. Гнуть полуобечайку, проверить по шаблону.</td></tr>
<tr><td colspan="11">5. Снять полуобечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр полуобечайки</td><td>Толщина листа,</td><td colspan="8">Длина полуобечайки L, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">h, мм, до</td><td>700</td><td>1000</td><td>1400</td><td>2000</td><td colspan="2">2800</td><td>4000</td><td>5600</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">1100</td><td>58</td><td>50</td><td>54</td><td>59</td><td>64</td><td colspan="2">69</td><td>75</td><td>81</td></tr>
<tr><td>2</td><td>80</td><td>59</td><td>63</td><td>68</td><td>73</td><td colspan="2">79</td><td>86</td><td>93</td></tr>
<tr><td>3</td><td>110</td><td>66</td><td>72</td><td>78</td><td>85</td><td colspan="2">91</td><td>99</td><td>107</td></tr>
<tr><td>4</td><td>160</td><td>78</td><td>85</td><td>92</td><td>100</td><td colspan="2">108</td><td>117</td><td>127</td></tr>
<tr><td>5</td><td rowspan="4">1500</td><td>58</td><td>56</td><td>61</td><td>66</td><td>71</td><td colspan="2">77</td><td>84</td><td>91</td></tr>
<tr><td>6</td><td>80</td><td>65</td><td>70</td><td>76</td><td>82</td><td colspan="2">89</td><td>97</td><td>104</td></tr>
<tr><td>7</td><td>110</td><td>74</td><td>80</td><td>87</td><td>95</td><td colspan="2">102</td><td>111</td><td>120</td></tr>
<tr><td>8</td><td>160</td><td>88</td><td>95</td><td>103</td><td>112</td><td colspan="2">121</td><td>131</td><td>142</td></tr>
<tr><td>9</td><td rowspan="4">2200</td><td>58</td><td>64</td><td>70</td><td>76</td><td>82</td><td colspan="2">89</td><td>96</td><td>104</td></tr>
<tr><td>10</td><td>80</td><td>74</td><td>81</td><td>87</td><td>95</td><td colspan="2">102</td><td>111</td><td>120</td></tr>
<tr><td>11</td><td>110</td><td>85</td><td>93</td><td>100</td><td>109</td><td colspan="2">118</td><td>128</td><td>138</td></tr>
<tr><td>12</td><td>160</td><td>101</td><td>109</td><td>118</td><td>128</td><td colspan="2">139</td><td>150</td><td>163</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="18%"><col width="11%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="4%"><col width="5%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="8" rowspan="2">Гибка толстостенных полуобечаек в горячем состоянии на прессе</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 33, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр полуобечайки</td><td>Толщина листа,</td><td colspan="8">Длина полуобечайки L, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">h, мм, до</td><td>700</td><td>1000</td><td>1400</td><td>2000</td><td colspan="2">2800</td><td>4000</td><td>5600</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>13</td><td rowspan="4">3000</td><td>58</td><td>72</td><td>78</td><td>85</td><td>92</td><td colspan="2">99</td><td>108</td><td>116</td></tr>
<tr><td>14</td><td>80</td><td>83</td><td>90</td><td>97</td><td>106</td><td colspan="2">114</td><td>124</td><td>134</td></tr>
<tr><td>15</td><td>110</td><td>96</td><td>104</td><td>112</td><td>122</td><td colspan="2">131</td><td>143</td><td>154</td></tr>
<tr><td>16</td><td>160</td><td>113</td><td>123</td><td>132</td><td>143</td><td colspan="2">155</td><td>168</td><td>182</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td></tr>
</table>


<a id="p102266"></a>Примечания: 1. При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<a id="p102269"></a><a id="p102270"></a>

<table>
<colgroup><col width="49%"><col width="26%"><col width="26%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="2">Материал</td></tr>
<tr><td>углеродистая сталь</td><td>легированная сталь</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,2</td></tr>
<tr><td>2. Работа выполняется бригадой из двух человек:</td><td></td><td></td></tr>
<tr><td>0,36</td><td>0,44 0,23</td><td></td></tr>
<tr><td>Т = 0,015 х Д</td><td>х h х L .</td><td></td></tr>
</table>




<table>
<colgroup><col width="5%"><col width="11%"><col width="11%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="10" rowspan="2">Гибка полосовой стали в кольца в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 34, лист 1</td></tr>
<tr><td colspan="14">Содержание работы</td></tr>
<tr><td colspan="14">1. Подать полосу к вальцам.</td></tr>
<tr><td colspan="14">2. Заправить кромку полосы в вальцы. (рисунок не</td></tr>
<tr><td colspan="14">3. Вальцевать полосу в кольцо. приводится)</td></tr>
<tr><td colspan="14">4. Проверить кольцо по диаметру шаблоном.</td></tr>
<tr><td colspan="14">5. Снять кольцо, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Высота, кольца</td><td>Диаметр кольца</td><td colspan="11">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">Д, мм, до</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td colspan="2">20</td><td>28</td><td>38</td><td>50</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="6">150</td><td>300</td><td>1,5</td><td>1,8</td><td>2,3</td><td>2,7</td><td>3,4</td><td>3,6</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>400</td><td>1,8</td><td>2,1</td><td>2,7</td><td>3,1</td><td>3,9</td><td>4,3</td><td colspan="2">5,3</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>550</td><td>2,2</td><td>2,5</td><td>3,2</td><td>3,8</td><td>4,7</td><td>5,1</td><td colspan="2">6,3</td><td>7,6</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>750</td><td>2,6</td><td>3,0</td><td>3,8</td><td>4,5</td><td>5,6</td><td>6,1</td><td colspan="2">7,5</td><td>9,0</td><td>10,7</td><td>-</td></tr>
<tr><td>5</td><td>1000</td><td>3,0</td><td>3,6</td><td>4,5</td><td>5,3</td><td>6,6</td><td>7,2</td><td colspan="2">8,8</td><td>10,6</td><td>12,6</td><td>14,7</td></tr>
<tr><td>6</td><td>1400</td><td>3,7</td><td>4,3</td><td>5,4</td><td>6,3</td><td>7,9</td><td>8,7</td><td colspan="2">10,6</td><td>12,8</td><td>15,2</td><td>17,7</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="11%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="10" rowspan="2">Гибка полосовой стали в кольца в холодном состоянии в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 34, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Высота, кольца</td><td>Диаметр кольца</td><td colspan="11">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">Д, мм, до</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td colspan="2">20</td><td>28</td><td>38</td><td>50</td></tr>
<tr><td></td><td></td><td></td><td></td><td></td><td></td><td colspan="2"></td><td></td><td></td><td></td></tr>
<tr><td>7</td><td rowspan="3">150</td><td>1800</td><td>-</td><td>4,9</td><td>6,2</td><td>7,3</td><td>9,2</td><td>10,0</td><td colspan="2">12,9</td><td>14,7</td><td>17,5</td><td>20,4</td></tr>
<tr><td>8</td><td>2400</td><td>-</td><td>-</td><td>7,3</td><td>8,6</td><td>10,8</td><td>11,7</td><td colspan="2">14,3</td><td>17,3</td><td>20,5</td><td>23,9</td></tr>
<tr><td>9</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>10,1</td><td>12,7</td><td>13,8</td><td colspan="2">16,8</td><td>20,3</td><td>24,1</td><td>28,2</td></tr>
<tr><td>10</td><td rowspan="10">300</td><td>300</td><td>1,7</td><td>2,0</td><td>2,5</td><td>3,0</td><td>3,5</td><td>4,1</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td>400</td><td>2,0</td><td>2,4</td><td>3,0</td><td>3,5</td><td>4,2</td><td>4,8</td><td colspan="2">5,8</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>550</td><td>2,4</td><td>2,8</td><td>3,5</td><td>4,2</td><td>5,0</td><td>5,7</td><td colspan="2">6,9</td><td>8,4</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>750</td><td>2,8</td><td>3,4</td><td>4,2</td><td>4,9</td><td>5,9</td><td>6,8</td><td colspan="2">8,2</td><td>9,9</td><td>11,8</td><td>-</td></tr>
<tr><td>14</td><td>1000</td><td>3,4</td><td>3,9</td><td>4,9</td><td>5,8</td><td>6,9</td><td>8,1</td><td colspan="2">9,7</td><td>11,7</td><td>13,9</td><td>16,2</td></tr>
<tr><td>15</td><td>1400</td><td>4,0</td><td>4,8</td><td>6,0</td><td>7,0</td><td>8,4</td><td>9,5</td><td colspan="2">11,7</td><td>14,1</td><td>16,8</td><td>19,6</td></tr>
<tr><td>16</td><td>1800</td><td>-</td><td>5,5</td><td>6,9</td><td>8,1</td><td>9,6</td><td>11,0</td><td colspan="2">13,5</td><td>16,3</td><td>19,3</td><td>22,5</td></tr>
<tr><td>17</td><td>2400</td><td>-</td><td>6,5</td><td>8,1</td><td>9,5</td><td>11,3</td><td>13,0</td><td colspan="2">15,8</td><td>19,1</td><td>22,7</td><td>26,5</td></tr>
<tr><td>18</td><td>3200</td><td>-</td><td>-</td><td>9,5</td><td>11,2</td><td>13,3</td><td>15,2</td><td colspan="2">18,6</td><td>22,5</td><td>26,7</td><td>31,1</td></tr>
<tr><td>19</td><td>4000</td><td>-</td><td>-</td><td>-</td><td>12,6</td><td>15,1</td><td>17,3</td><td colspan="2">21,0</td><td>25,5</td><td>30,2</td><td>35,2</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="76%"><col width="24%"></colgroup>
<tr><td rowspan="2">Гибка полосовой стали в кольца в холодном состоянии в вальцах</td><td>Гибка</td></tr>
<tr><td>Карта 34, лист 3</td></tr>
</table>


<a id="p102306"></a>Примечания: 1. Нормативы времени рассчитаны на гибку колец в холодном состоянии и предварительно подогнутыми кромками.
2. <a id="p102307"></a>Время на подгибку кромок брать по карте 22 или 23.
3. <a id="p102308"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="12%"><col width="7%"><col width="7%"><col width="6%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"><col width="4%"><col width="8%"><col width="7%"><col width="5%"><col width="6%"><col width="4%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="3">Материал</td><td colspan="9">Количество одновременно сгибаемых колец</td><td colspan="2">Гибка полосовой стали в кольца</td><td colspan="3">Скорость вращения валков, м/мин.</td></tr>
<tr><td>времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>1</td><td>2</td><td>3</td><td>4</td><td>5</td><td>6</td><td>7</td><td>8</td><td>св. 8</td><td>цилиндрические</td><td>эллиптические</td><td>до 6</td><td>7 - 8</td><td>св. 8</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,7</td><td>0,55</td><td>0,45</td><td>0,4</td><td>0,35</td><td>0,3</td><td>0,25</td><td>0,2</td><td>1,0</td><td>1,3</td><td>1,2</td><td>1,0</td><td>0,8</td></tr>
</table>


4. <a id="p102311"></a>Работа выполняется бригадой из двух человек:

                                0,56    0,56
<a id="p102312"></a>                  Т = 0,0343 х Д     х L           поз. 1...9;

                                0,56    0,56
<a id="p102313"></a>                  Т = 0,0379 х Д     х L           поз. 10...19.


<table>
<colgroup><col width="5%"><col width="8%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12" rowspan="2">Гибка полосовой стали в полукольца в холодном состоянии в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 35, лист 1</td></tr>
<tr><td colspan="16">Содержание работы</td></tr>
<tr><td colspan="16">1. Подать полосу к вальцам.</td></tr>
<tr><td colspan="16">2. Заправить кромку полосы в вальцы. (рисунок не</td></tr>
<tr><td colspan="16">3. Вальцевать полосу в полукольцо. приводится)</td></tr>
<tr><td colspan="16">4. Проверить полукольцо по диаметру шаблоном.</td></tr>
<tr><td colspan="16">5. Снять полукольцо, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Высота кольца</td><td>Диаметр кольца</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">Н, мм, до</td><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td colspan="2">28</td><td>38</td><td>50</td><td>80</td></tr>
<tr><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="7">150</td><td>200</td><td>0,61</td><td>0,74</td><td>0,85</td><td>1,03</td><td>1,19</td><td>1,44</td><td>1,55</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>300</td><td>0,79</td><td>0,95</td><td>1,10</td><td>1,33</td><td>1,53</td><td>1,86</td><td>2,00</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>400</td><td>0,94</td><td>1,15</td><td>1,32</td><td>1,60</td><td>1,84</td><td>2,23</td><td>2,40</td><td>2,85</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>500</td><td>1,15</td><td>1,40</td><td>1,61</td><td>1,95</td><td>2,24</td><td>2,72</td><td>2,94</td><td>3,50</td><td colspan="2">4,10</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>750</td><td>1,40</td><td>1,70</td><td>1,95</td><td>2,38</td><td>2,73</td><td>3,30</td><td>3,60</td><td>4,20</td><td colspan="2">4,90</td><td>5,70</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>1000</td><td>-</td><td>2,04</td><td>2,34</td><td>2,85</td><td>3,27</td><td>3,90</td><td>4,30</td><td>5,10</td><td colspan="2">5,92</td><td>6,94</td><td>8,10</td><td>-</td></tr>
<tr><td>7</td><td>1350</td><td>-</td><td>2,53</td><td>2,84</td><td>3,41</td><td>3,90</td><td>4,81</td><td>5,21</td><td>6,13</td><td colspan="2">7,22</td><td>8,34</td><td>9,55</td><td>11,90</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="8%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12" rowspan="2">Гибка полосовой стали в полукольца в холодном состоянии в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 35, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Высота кольца</td><td>Диаметр кольца</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">Н, мм, до</td><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>4</td><td>6</td><td>8</td><td>12</td><td>14</td><td>20</td><td colspan="2">28</td><td>38</td><td>50</td><td>80</td></tr>
<tr><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>8</td><td>150</td><td>1800</td><td>-</td><td>-</td><td>3,41</td><td>4,13</td><td>4,75</td><td>5,71</td><td>0,22</td><td>7,31</td><td colspan="2">8,62</td><td>10,00</td><td>11,45</td><td>14,32</td></tr>
<tr><td>9</td><td rowspan="12">300</td><td>200</td><td>0,67</td><td>0,81</td><td>6,93</td><td>1,13</td><td>1,31</td><td>1,58</td><td>1,72</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>300</td><td>0,84</td><td>1,05</td><td>1,21</td><td>1,46</td><td>1,67</td><td>2,04</td><td>2,20</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td>400</td><td>1,03</td><td>1,25</td><td>1,44</td><td>1,75</td><td>2,00</td><td>2,40</td><td>2,60</td><td>3,10</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>550</td><td>1,26</td><td>1,53</td><td>1,76</td><td>2,14</td><td>2,45</td><td>2,98</td><td>3,21</td><td>3,81</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>750</td><td>1,53</td><td>1,86</td><td>2,14</td><td>2,60</td><td>2,98</td><td>3,63</td><td>3,91</td><td>4,63</td><td colspan="2">5,45</td><td>6,31</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td>1000</td><td>-</td><td>2,23</td><td>2,56</td><td>3,12</td><td>3,60</td><td>4,30</td><td>4,71</td><td>5,62</td><td colspan="2">6,51</td><td>7,53</td><td>8,64</td><td>-</td></tr>
<tr><td>15</td><td>1350</td><td>-</td><td>2,81</td><td>3,24</td><td>3,91</td><td>4,52</td><td>5,53</td><td>5,94</td><td>7,01</td><td colspan="2">8,23</td><td>9,53</td><td>10,82</td><td>13,00</td></tr>
<tr><td>16</td><td>1800</td><td>-</td><td>-</td><td>3,75</td><td>4,51</td><td>5,25</td><td>6,31</td><td>6,85</td><td>8,10</td><td colspan="2">9,51</td><td>10,91</td><td>12,55</td><td>15,61</td></tr>
<tr><td>17</td><td>2400</td><td>-</td><td>-</td><td>4,43</td><td>5,41</td><td>6,22</td><td>7,53</td><td>8,10</td><td>9,63</td><td colspan="2">11,30</td><td>13,10</td><td>14,91</td><td>18,80</td></tr>
<tr><td>18</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>6,51</td><td>7,44</td><td>9,00</td><td>9,73</td><td>11,60</td><td colspan="2">13,60</td><td>15,71</td><td>17,95</td><td>22,50</td></tr>
<tr><td>19</td><td>4000</td><td>-</td><td>-</td><td>-</td><td>7,51</td><td>8,64</td><td>10,41</td><td>11,20</td><td>13,31</td><td colspan="2">15,62</td><td>18,10</td><td>20,60</td><td>25,90</td></tr>
<tr><td>20</td><td>5000</td><td>-</td><td>-</td><td>-</td><td>8,61</td><td>9,85</td><td>11,90</td><td>12,95</td><td>15,31</td><td colspan="2">18,00</td><td>20,80</td><td>23,80</td><td>29,80</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="74%"><col width="26%"></colgroup>
<tr><td rowspan="2">Гибка полосовой стали в полукольца в холодном состоянии в вальцах</td><td>Гибка</td></tr>
<tr><td>Карта 35, лист 3</td></tr>
</table>


<a id="p102350"></a>Примечания: 1. Нормативы времени рассчитаны на гибку полуколец с предварительно подогнутыми кромками.
2. <a id="p102351"></a>Время на подгибку кромок брать по карте 22 или 23.
3. <a id="p102352"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="12%"><col width="7%"><col width="7%"><col width="6%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"><col width="4%"><col width="8%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td><td colspan="9">Кол-во одновременно сгибаемых колец</td><td colspan="2">Гибка полосовой стали в полукольца</td><td colspan="3">Скорость вращения валков, м/мин.</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>1</td><td>2</td><td>3</td><td>4</td><td>5</td><td>6</td><td>7</td><td>8</td><td>св. 8</td><td>цилиндрические</td><td>эллиптические</td><td>до 6</td><td>7 - 8</td><td>св. 8</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,7</td><td>0,55</td><td>0,45</td><td>0,4</td><td>0,35</td><td>0,3</td><td>0,25</td><td>0,2</td><td>1,0</td><td>1,3</td><td>1,2</td><td>1,0</td><td>0,8</td></tr>
</table>


4. <a id="p102356"></a>Работа выполняется бригадой из двух человек:

                                 0,13    0,63    0,48
<a id="p102357"></a>                   Т = 0,0081 х Н     х Д     х h    .


<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Гибка листов на кромкогибочном прессе</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 36, лист 1</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">1. Подать лист к прессу. (рисунок не</td></tr>
<tr><td colspan="13">2. Установить лист на пресс по разметке. приводится)</td></tr>
<tr><td colspan="13">3. Гнуть лист.</td></tr>
<tr><td colspan="13">4. Снять лист, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина листа В,</td><td>Длина листа</td><td colspan="10">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">мм, до</td><td rowspan="2">L, мм, до</td><td>2</td><td>4</td><td>6</td><td>8</td><td>10</td><td colspan="2">12</td><td>16</td><td>20</td><td>24</td></tr>
<tr><td colspan="10"></td></tr>
<tr><td>1</td><td rowspan="5">250</td><td>250</td><td>0,20</td><td>0,30</td><td>0,38</td><td>0,46</td><td>0,52</td><td colspan="2">0,58</td><td>0,69</td><td>0,79</td><td>0,88</td></tr>
<tr><td>2</td><td>450</td><td>0,27</td><td>0,41</td><td>0,53</td><td>0,62</td><td>0,71</td><td colspan="2">0,80</td><td>0,95</td><td>1,08</td><td>1,21</td></tr>
<tr><td>3</td><td>750</td><td>0,36</td><td>0,54</td><td>0,69</td><td>0,82</td><td>0,94</td><td colspan="2">1,04</td><td>1,24</td><td>1,42</td><td>1,58</td></tr>
<tr><td>4</td><td>1250</td><td>0,47</td><td>0,71</td><td>0,90</td><td>1,07</td><td>1,23</td><td colspan="2">1,37</td><td>1,63</td><td>1,86</td><td>2,10</td></tr>
<tr><td>5</td><td>1800</td><td>0,57</td><td>0,86</td><td>1,20</td><td>1,30</td><td>1,49</td><td colspan="2">1,66</td><td>1,98</td><td>2,30</td><td>2,50</td></tr>
<tr><td>6</td><td rowspan="5">450</td><td>250</td><td>0,30</td><td>0,45</td><td>0,57</td><td>0,68</td><td>0,78</td><td colspan="2">0,87</td><td>1,03</td><td>1,18</td><td>1,32</td></tr>
<tr><td>7</td><td>450</td><td>0,41</td><td>0,61</td><td>0,78</td><td>0,93</td><td>1,07</td><td colspan="2">1,19</td><td>1,41</td><td>1,62</td><td>1,80</td></tr>
<tr><td>8</td><td>750</td><td>0,53</td><td>0,81</td><td>1,03</td><td>1,22</td><td>1,40</td><td colspan="2">1,60</td><td>1,85</td><td>2,10</td><td>2,40</td></tr>
<tr><td>9</td><td>1250</td><td>0,70</td><td>1,06</td><td>1,35</td><td>1,60</td><td>1,83</td><td colspan="2">2,00</td><td>2,4</td><td>2,80</td><td>3,10</td></tr>
<tr><td>10</td><td>1800</td><td>0,85</td><td>1,28</td><td>1,64</td><td>1,94</td><td>2,20</td><td colspan="2">2,50</td><td>2,9</td><td>3,40</td><td>3,80</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Гибка листов на кромкогибочном прессе</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 36, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина листа В,</td><td>Длина листа</td><td colspan="10">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">мм, до</td><td rowspan="2">L, мм, до</td><td>2</td><td>4</td><td>6</td><td>8</td><td>10</td><td colspan="2">12</td><td>16</td><td>20</td><td>24</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>11</td><td>450</td><td>2500</td><td>1,01</td><td>1,63</td><td>1,95</td><td>2,30</td><td>2,60</td><td colspan="2">2,9</td><td>3,5</td><td>4,0</td><td>4,5</td></tr>
<tr><td>12</td><td rowspan="6">750</td><td>250</td><td>0,42</td><td>0,64</td><td>0,81</td><td>0,97</td><td>1,10</td><td colspan="2">1,2</td><td>1,4</td><td>1,6</td><td>1,8</td></tr>
<tr><td>13</td><td>450</td><td>0,57</td><td>0,87</td><td>1,11</td><td>1,32</td><td>1,51</td><td colspan="2">1,6</td><td>2,0</td><td>2,3</td><td>2,5</td></tr>
<tr><td>14</td><td>750</td><td>0,75</td><td>1,14</td><td>1,46</td><td>1,73</td><td>1,98</td><td colspan="2">2,2</td><td>2,6</td><td>3,1</td><td>3,3</td></tr>
<tr><td>15</td><td>1250</td><td>0,99</td><td>1,50</td><td>1,91</td><td>2,30</td><td>2,60</td><td colspan="2">2,9</td><td>3,4</td><td>3,9</td><td>4,4</td></tr>
<tr><td>16</td><td>1800</td><td>1,20</td><td>1,81</td><td>2,30</td><td>2,70</td><td>3,10</td><td colspan="2">3,5</td><td>4,2</td><td>4,8</td><td>5,3</td></tr>
<tr><td>17</td><td>2500</td><td>1,42</td><td>2,20</td><td>2,80</td><td>3,30</td><td>3,70</td><td colspan="2">4,2</td><td>5,0</td><td>5,7</td><td>6,3</td></tr>
<tr><td>18</td><td rowspan="6">1250</td><td>250</td><td>0,59</td><td>0,90</td><td>1,15</td><td>1,37</td><td>1,56</td><td colspan="2">1,7</td><td>2,1</td><td>2,4</td><td>2,6</td></tr>
<tr><td>19</td><td>450</td><td>0,81</td><td>1,23</td><td>1,57</td><td>1,87</td><td>2,10</td><td colspan="2">2,4</td><td>2,8</td><td>3,2</td><td>3,6</td></tr>
<tr><td>20</td><td>750</td><td>1,06</td><td>1,61</td><td>2,10</td><td>2,40</td><td>2,80</td><td colspan="2">3,1</td><td>3,7</td><td>4,2</td><td>4,7</td></tr>
<tr><td>21</td><td>1250</td><td>1,40</td><td>2,10</td><td>2,70</td><td>3,20</td><td>3,70</td><td colspan="2">4,1</td><td>4,9</td><td>5,6</td><td>6,2</td></tr>
<tr><td>22</td><td>1800</td><td>1,69</td><td>2,60</td><td>3,30</td><td>3,90</td><td>4,40</td><td colspan="2">5,0</td><td>5,9</td><td>6,7</td><td>7,5</td></tr>
<tr><td>23</td><td>2500</td><td>2,00</td><td>3,10</td><td>3,90</td><td>4,6</td><td>5,3</td><td colspan="2">5,9</td><td>7,0</td><td>8,0</td><td>9,0</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Гибка листов на кромкогибочном прессе</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 36, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина листа В,</td><td>Длина листа</td><td colspan="10">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">мм, до</td><td rowspan="2">L, мм, до</td><td>2</td><td>4</td><td>6</td><td>8</td><td>10</td><td colspan="2">12</td><td>16</td><td>20</td><td>24</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>24</td><td rowspan="6">1800</td><td>250</td><td>0,84</td><td>1,2</td><td>1,6</td><td>1,9</td><td>2,2</td><td colspan="2">2,4</td><td>2,9</td><td>3,3</td><td>3,7</td></tr>
<tr><td>25</td><td>450</td><td>1,14</td><td>1,7</td><td>2,2</td><td>2,6</td><td>3,0</td><td colspan="2">3,3</td><td>4,0</td><td>4,5</td><td>5,1</td></tr>
<tr><td>26</td><td>750</td><td>1,50</td><td>2,3</td><td>2,9</td><td>3,4</td><td>3,9</td><td colspan="2">4,4</td><td>5,2</td><td>6,0</td><td>6,7</td></tr>
<tr><td>27</td><td>1250</td><td>1,97</td><td>3,0</td><td>3,8</td><td>4,5</td><td>5,2</td><td colspan="2">5,8</td><td>6,8</td><td>7,8</td><td>8,7</td></tr>
<tr><td>28</td><td>1800</td><td>2,40</td><td>3,6</td><td>4,6</td><td>5,5</td><td>6,3</td><td colspan="2">7,0</td><td>8,3</td><td>9,5</td><td>10,6</td></tr>
<tr><td>29</td><td>2500</td><td>2,80</td><td>4,3</td><td>5,5</td><td>6,5</td><td>7,4</td><td colspan="2">8,3</td><td>9,9</td><td>11,3</td><td>12,6</td></tr>
<tr><td>30</td><td rowspan="5">2500</td><td>450</td><td>1,52</td><td>2,3</td><td>2,9</td><td>3,5</td><td>4,0</td><td colspan="2">4,4</td><td>5,3</td><td>6,0</td><td>6,7</td></tr>
<tr><td>31</td><td>750</td><td>1,99</td><td>3,0</td><td>3,8</td><td>4,6</td><td>5,2</td><td colspan="2">6,8</td><td>6,9</td><td>7,9</td><td>8,8</td></tr>
<tr><td>32</td><td>1250</td><td>2,60</td><td>3,9</td><td>5,0</td><td>6,0</td><td>6,8</td><td colspan="2">7,6</td><td>9,1</td><td>10,4</td><td>11,6</td></tr>
<tr><td>33</td><td>1800</td><td>3,20</td><td>4,8</td><td>6,1</td><td>7,3</td><td>8,3</td><td colspan="2">9,3</td><td>11,0</td><td>12,6</td><td>14,0</td></tr>
<tr><td>34</td><td>2500</td><td>3,80</td><td>5,7</td><td>7,3</td><td>8,6</td><td>9,9</td><td colspan="2">11,0</td><td>13,1</td><td>15,0</td><td>16,7</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Гибка листов на кромкогибочном прессе</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 36, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина листа В,</td><td>Длина листа</td><td colspan="10">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">мм, до</td><td rowspan="2">L, мм, до</td><td>2</td><td>4</td><td>6</td><td>8</td><td>10</td><td colspan="2">12</td><td>16</td><td>20</td><td>24</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>35</td><td rowspan="5">3550</td><td>450</td><td>2,0</td><td>3,1</td><td>4,0</td><td>4,7</td><td>5,4</td><td colspan="2">6,0</td><td>7,1</td><td>8,2</td><td>9,1</td></tr>
<tr><td>36</td><td>750</td><td>2,7</td><td>4,1</td><td>5,2</td><td>6,2</td><td>7,1</td><td colspan="2">7,9</td><td>9,4</td><td>10,7</td><td>11,9</td></tr>
<tr><td>37</td><td>1250</td><td>3,5</td><td>5,3</td><td>6,8</td><td>8,1</td><td>9,3</td><td colspan="2">10,3</td><td>12,3</td><td>14,0</td><td>15,6</td></tr>
<tr><td>38</td><td>1800</td><td>4,3</td><td>6,5</td><td>8,3</td><td>9,8</td><td>11,2</td><td colspan="2">12,5</td><td>14,9</td><td>17,0</td><td>18,9</td></tr>
<tr><td>39</td><td>2500</td><td>5,1</td><td>7,7</td><td>9,8</td><td>11,7</td><td>13,4</td><td colspan="2">14,9</td><td>17,7</td><td>20,3</td><td>22,6</td></tr>
<tr><td>40</td><td rowspan="5">4500</td><td>450</td><td>2,5</td><td>3,8</td><td>4,9</td><td>5,8</td><td>6,6</td><td colspan="2">7,4</td><td>8,7</td><td>10,0</td><td>11,2</td></tr>
<tr><td>41</td><td>750</td><td>3,3</td><td>5,0</td><td>6,4</td><td>7,6</td><td>8,7</td><td colspan="2">9,7</td><td>11,5</td><td>13,1</td><td>14,6</td></tr>
<tr><td>42</td><td>1250</td><td>4,3</td><td>6,5</td><td>8,4</td><td>9,9</td><td>11,3</td><td colspan="2">12,7</td><td>15,0</td><td>17,2</td><td>19,2</td></tr>
<tr><td>43</td><td>1800</td><td>5,2</td><td>7,0</td><td>10,1</td><td>12,1</td><td>13,8</td><td colspan="2">15,4</td><td>18,3</td><td>20,9</td><td>23,3</td></tr>
<tr><td>44</td><td>2500</td><td>6,2</td><td>9,5</td><td>12,1</td><td>14,3</td><td>16,4</td><td colspan="2">18,3</td><td>21,7</td><td>24,8</td><td>27,7</td></tr>
<tr><td>45</td><td rowspan="5">5600</td><td>450</td><td>3,0</td><td>4,6</td><td>5,9</td><td>7,0</td><td>8,0</td><td colspan="2">8,9</td><td>10,6</td><td>12,1</td><td>13,5</td></tr>
<tr><td>46</td><td>750</td><td>4,0</td><td>6,0</td><td>7,7</td><td>9,1</td><td>10,4</td><td colspan="2">11,7</td><td>13,9</td><td>15,8</td><td>17,7</td></tr>
<tr><td>47</td><td>1250</td><td>5,2</td><td>7,9</td><td>10,1</td><td>12,0</td><td>13,7</td><td colspan="2">15,3</td><td>18,2</td><td>20,8</td><td>23,2</td></tr>
<tr><td>48</td><td>1800</td><td>6,3</td><td>9,6</td><td>12,2</td><td>14,5</td><td>16,6</td><td colspan="2">18,5</td><td>22,0</td><td>25,2</td><td>28,1</td></tr>
<tr><td>49</td><td>2500</td><td>7,5</td><td>11,4</td><td>14,6</td><td>17,3</td><td>19,8</td><td colspan="2">22,1</td><td>26,2</td><td>30,0</td><td>33,5</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="76%"><col width="24%"></colgroup>
<tr><td rowspan="2">Гибка листов на кромкогибочном прессе</td><td>Гибка</td></tr>
<tr><td>Карта 36, лист 5</td></tr>
</table>


<a id="p102430"></a>Примечания: 1. Нормативы времени рассчитаны на гибку листов по разметке в специальных (или универсальных) приспособлениях полностью, соответствующих требованиям к гибке данной детали, за 1 - 2 хода ползуна.
2. <a id="p102431"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="10%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="3%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение</td><td colspan="5">Вид изгибаемого профиля и число гибов</td><td colspan="5" rowspan="2">Кол-во одновременно устанавливаемых листов для гибки</td><td colspan="4" rowspan="2">Гибка</td></tr>
<tr><td colspan="2">1 гиб</td><td>2 гиба</td><td>3 гиба</td><td>4 гиба</td></tr>
<tr><td>нормы времени</td><td>изображение профиля не приводится</td><td>изображение профиля не приводится</td><td>изображение профиля не приводится</td><td>изображение профиля не приводится</td><td>изображение профиля не приводится</td><td>1</td><td>2</td><td>3</td><td>4</td><td>св. 4</td><td>по упору</td><td>по разметке</td><td>с подправкой на прессе</td><td>с подправкой на плите</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,3</td><td>1,8</td><td>2,6</td><td>3,5</td><td>10</td><td>0,8</td><td>0,7</td><td>0,65</td><td>0,6</td><td>0,8</td><td>1,0</td><td>1,4</td><td>1,55</td></tr>
</table>


3. <a id="p102434"></a>Работа выполняется бригадой из двух человек:

                         0,68    0,43    0,6
<a id="p102435"></a>         Т = 0,000165 х В     х L     х h       для В <= 1250 мм;

                         0,86    0,53    0,6
<a id="p102436"></a>         Т = 0,000047 х В     х L     х h       для В > 1250 мм.


<table>
<colgroup><col width="5%"><col width="11%"><col width="11%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Гибка полосовой стали в горячем состоянии на фланцегибочной машине</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 37, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Загрузить полосы в нагревательную печь.</td></tr>
<tr><td colspan="12">2. Выгрузить полосы из печи и подать на стол машины.</td></tr>
<tr><td colspan="12">3. Зажать полосу.</td></tr>
<tr><td colspan="12">4. Гнуть полосу по шаблону с подправкой кувалдой.</td></tr>
<tr><td colspan="12">5. Снять фланец со стола и править по плоскости и диаметру на плите.</td></tr>
<tr><td colspan="12">6. Отложить фланец.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина полосы</td><td>Толщина полосы</td><td colspan="9">Внутренний диаметр фланца d, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">h, мм, до</td><td>350</td><td>450</td><td>550</td><td>700</td><td>850</td><td>1000</td><td>1100</td><td>1200</td><td>1400</td></tr>
<tr><td colspan="9">Время на фланец Т, чел.-мин.</td></tr>
<tr><td>1</td><td>60</td><td>20</td><td>2,48</td><td>3,14</td><td>3,78</td><td>4,7</td><td>5,6</td><td>6,5</td><td>7,2</td><td>7,8</td><td>9,0</td></tr>
<tr><td>2</td><td rowspan="2">65</td><td>24</td><td>3,01</td><td>3,81</td><td>4,59</td><td>5,7</td><td>6,8</td><td>8,0</td><td>8,7</td><td>9,4</td><td>10,9</td></tr>
<tr><td>3</td><td>34</td><td>3,48</td><td>4,40</td><td>5,30</td><td>6,6</td><td>7,9</td><td>9,2</td><td>10,1</td><td>10,9</td><td>12,6</td></tr>
<tr><td>4</td><td>75</td><td>36</td><td>4,41</td><td>5,57</td><td>6,71</td><td>8,4</td><td>10,0</td><td>11,7</td><td>12,8</td><td>13,9</td><td>16,0</td></tr>
<tr><td>5</td><td rowspan="2">85</td><td>40</td><td>5,80</td><td>7,33</td><td>8,84</td><td>11,0</td><td>13,2</td><td>15,4</td><td>16,8</td><td>18,3</td><td>21,1</td></tr>
<tr><td>6</td><td>60</td><td>6,96</td><td>8,8</td><td>10,6</td><td>13,3</td><td>15,9</td><td>18,5</td><td>20,2</td><td>21,9</td><td>25,3</td></tr>
<tr><td>7</td><td rowspan="2">95</td><td>40</td><td>6,96</td><td>8,8</td><td>10,6</td><td>13,3</td><td>15,9</td><td>18,5</td><td>20,2</td><td>21,9</td><td>25,3</td></tr>
<tr><td>8</td><td>50</td><td>7,70</td><td>9,68</td><td>11,7</td><td>14,6</td><td>17,5</td><td>20,3</td><td>22,2</td><td>24,1</td><td>28,4</td></tr>
<tr><td>9</td><td>105</td><td>60</td><td>9,75</td><td>12,3</td><td>14,8</td><td>18,6</td><td>22,3</td><td>25,9</td><td>28,3</td><td>30,7</td><td>35,4</td></tr>
<tr><td>10</td><td>115</td><td>50</td><td>10,2</td><td>12,9</td><td>15,5</td><td>19,5</td><td>23,3</td><td>27,1</td><td>29,6</td><td>32,1</td><td>37,1</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="76%"><col width="24%"></colgroup>
<tr><td rowspan="2">Гибка полосовой стали в горячем состоянии на фланцегибочной машине</td><td>Гибка</td></tr>
<tr><td>Карта 37, лист 2</td></tr>
</table>


<a id="p102460"></a>Примечания: 1. При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="28%"><col width="20%"><col width="20%"><col width="15%"><col width="16%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="2">Материал</td><td colspan="2">Гибка</td></tr>
<tr><td>времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>фланца</td><td>полуфланца</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p102463"></a>Работа выполняется одним человеком:

                                    1,53    0,47    0,93
<a id="p102464"></a>                    Т = 0,000005 х В     х h     х d    .


<table>
<colgroup><col width="5%"><col width="10%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в кольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 38, лист 1</td></tr>
<tr><td colspan="16">Содержание работы</td></tr>
<tr><td colspan="16">1. Подать полосу к вальцам.</td></tr>
<tr><td colspan="16">2. Заправить полосу в вальцы.</td></tr>
<tr><td colspan="16">3. Гнуть полосу на ребро в кольцо.</td></tr>
<tr><td colspan="16">4. Проверить по диаметру шаблоном.</td></tr>
<tr><td colspan="16">5. Снять кольцо, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Внутренний</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>диаметр кольца</td><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="6">550</td><td>30</td><td>3,10</td><td>3,61</td><td>4,0</td><td>4,4</td><td>4,8</td><td>5,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>50</td><td>3,80</td><td>4,43</td><td>4,9</td><td>5,5</td><td>6,0</td><td>6,4</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>70</td><td>4,35</td><td>5,1</td><td>5,7</td><td>6,3</td><td>6,8</td><td>7,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>90</td><td>4,81</td><td>5,6</td><td>6,3</td><td>7,0</td><td>7,5</td><td>8,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>120</td><td>5,40</td><td>6,3</td><td>7,1</td><td>7,5</td><td>8,5</td><td>9,1</td><td>10,2</td><td>11,3</td><td>12,2</td><td>14,4</td><td>16,6</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>160</td><td>6,10</td><td>7,1</td><td>7,9</td><td>8,7</td><td>9,5</td><td>10,2</td><td>11,5</td><td>12,6</td><td>13,7</td><td>16,1</td><td>18,6</td><td>-</td><td>-</td></tr>
<tr><td></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в кольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 38, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Внутренний</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>диаметр кольца</td><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>7</td><td rowspan="6">750</td><td>30</td><td>3,6</td><td>4,2</td><td>4,8</td><td>5,3</td><td>5,8</td><td>6,2</td><td>7,0</td><td>7,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>50</td><td>4,5</td><td>5,3</td><td>5,9</td><td>6,5</td><td>7,1</td><td>7,6</td><td>8,5</td><td>9,4</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>70</td><td>5,2</td><td>6,0</td><td>6,7</td><td>7,5</td><td>8,1</td><td>8,7</td><td>9,8</td><td>11,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>90</td><td>5,7</td><td>6,7</td><td>7,5</td><td>8,2</td><td>8,9</td><td>9,6</td><td>10,8</td><td>11,9</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td>120</td><td>6,4</td><td>7,5</td><td>8,4</td><td>9,2</td><td>10,0</td><td>10,8</td><td>12,1</td><td>13,4</td><td>14,5</td><td>17,0</td><td>19,7</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>160</td><td>7,2</td><td>8,4</td><td>9,4</td><td>10,4</td><td>11,3</td><td>12,1</td><td>13,6</td><td>15,0</td><td>16,3</td><td>19,1</td><td>22,1</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td rowspan="6">1000</td><td>30</td><td>4,3</td><td>5,0</td><td>5,7</td><td>6,2</td><td>6,8</td><td>7,2</td><td>8,2</td><td>9,0</td><td>9,7</td><td>11,5</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td>50</td><td>5,3</td><td>6,2</td><td>6,9</td><td>7,6</td><td>8,3</td><td>8,9</td><td>10,0</td><td>11,0</td><td>12,0</td><td>14,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>70</td><td>6,0</td><td>7,0</td><td>7,9</td><td>8,7</td><td>9,5</td><td>10,2</td><td>11,4</td><td>12,6</td><td>13,7</td><td>16,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>90</td><td>6,7</td><td>7,8</td><td>8,8</td><td>9,7</td><td>10,5</td><td>11,2</td><td>12,7</td><td>13,9</td><td>15,1</td><td>17,8</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td>120</td><td>7,5</td><td>8,7</td><td>9,8</td><td>10,8</td><td>11,8</td><td>12,6</td><td>14,2</td><td>15,6</td><td>17,0</td><td>20</td><td>23,1</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td>160</td><td>8,4</td><td>9,8</td><td>11,0</td><td>12,2</td><td>13,2</td><td>14,2</td><td>15,9</td><td>17,5</td><td>19,0</td><td>22,4</td><td>25,9</td><td>-</td><td>-</td></tr>
<tr><td></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в кольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 38, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Внутренний</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>диаметр кольца</td><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>19</td><td rowspan="6">1350</td><td>30</td><td>5,1</td><td>5,9</td><td>6,7</td><td>7,3</td><td>8,0</td><td>8,5</td><td>9,6</td><td>10,6</td><td>11,5</td><td>13,5</td><td>15,6</td><td>18,0</td><td>-</td></tr>
<tr><td>20</td><td>50</td><td>6,2</td><td>7,3</td><td>8,2</td><td>9,0</td><td>9,8</td><td>10,5</td><td>11,8</td><td>13,0</td><td>14,1</td><td>16,</td><td>19,2</td><td>22,0</td><td>-</td></tr>
<tr><td>21</td><td>70</td><td>7,1</td><td>8,3</td><td>9,4</td><td>10,3</td><td>11,2</td><td>12,0</td><td>13,5</td><td>14,9</td><td>16,1</td><td>19,0</td><td>21,9</td><td>25,2</td><td>-</td></tr>
<tr><td>22</td><td>90</td><td>7,9</td><td>9,2</td><td>10,3</td><td>11,4</td><td>12,4</td><td>13,3</td><td>14,9</td><td>16,4</td><td>17,8</td><td>21,0</td><td>24,3</td><td>27,9</td><td>-</td></tr>
<tr><td>23</td><td>120</td><td>8,8</td><td>10,3</td><td>11,6</td><td>12,8</td><td>13,9</td><td>14,9</td><td>16,7</td><td>18,4</td><td>20,0</td><td>23,5</td><td>27,2</td><td>31,3</td><td>-</td></tr>
<tr><td>24</td><td>160</td><td>9,9</td><td>11,6</td><td>13,0</td><td>14,3</td><td>15,6</td><td>16,7</td><td>18,8</td><td>20,7</td><td>22,5</td><td>26,4</td><td>30,5</td><td>35,1</td><td>-</td></tr>
<tr><td>25</td><td rowspan="6">1800</td><td>30</td><td>6,0</td><td>6,9</td><td>7,8</td><td>8,6</td><td>9,3</td><td>10,0</td><td>11,3</td><td>12,4</td><td>13,5</td><td>15,8</td><td>18,3</td><td>21,0</td><td>23,5</td></tr>
<tr><td>26</td><td>50</td><td>7,3</td><td>8,5</td><td>9,6</td><td>10,5</td><td>11,4</td><td>12,3</td><td>13,8</td><td>15,2</td><td>16,5</td><td>19,4</td><td>22,5</td><td>25,8</td><td>28,8</td></tr>
<tr><td>27</td><td>70</td><td>8,4</td><td>9,7</td><td>11,0</td><td>12,1</td><td>13,1</td><td>14,1</td><td>15,8</td><td>17,4</td><td>18,9</td><td>22,2</td><td>25,7</td><td>29,5</td><td>33,0</td></tr>
<tr><td>28</td><td>90</td><td>9,2</td><td>10,8</td><td>12,1</td><td>13,3</td><td>14,5</td><td>15,5</td><td>17,5</td><td>19,3</td><td>20,9</td><td>24,6</td><td>28,4</td><td>32,7</td><td>36,4</td></tr>
<tr><td>29</td><td>120</td><td>10,4</td><td>12,1</td><td>13,6</td><td>15,0</td><td>16,2</td><td>17,4</td><td>19,6</td><td>21,6</td><td>23,4</td><td>27,6</td><td>31,9</td><td>36,6</td><td>40,9</td></tr>
<tr><td>30</td><td>160</td><td>11,6</td><td>13,5</td><td>15,2</td><td>16,8</td><td>18,2</td><td>19,6</td><td>22,0</td><td>24,2</td><td>26,3</td><td>30,9</td><td>35,8</td><td>41,1</td><td>45,9</td></tr>
<tr><td></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в кольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 38, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Внутренний</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>диаметр кольца</td><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>31</td><td rowspan="6">2400</td><td>30</td><td>7,0</td><td>8,1</td><td>9,1</td><td>10,1</td><td>10,9</td><td>11,7</td><td>13,2</td><td>14,5</td><td>15,8</td><td>18,5</td><td>21,4</td><td>24,6</td><td>27,5</td></tr>
<tr><td>32</td><td>50</td><td>8,6</td><td>10,0</td><td>11,2</td><td>12,4</td><td>13,4</td><td>14,4</td><td>16,2</td><td>17,8</td><td>19,4</td><td>22,8</td><td>26,3</td><td>30,2</td><td>33,8</td></tr>
<tr><td>33</td><td>70</td><td>9,8</td><td>11,4</td><td>12,8</td><td>14,1</td><td>15,3</td><td>16,5</td><td>18,5</td><td>20,4</td><td>22,1</td><td>26,0</td><td>30,1</td><td>34,6</td><td>38,6</td></tr>
<tr><td>34</td><td>90</td><td>10,8</td><td>12,6</td><td>14,2</td><td>15,6</td><td>17,0</td><td>18,2</td><td>20,5</td><td>22,6</td><td>24,5</td><td>28,8</td><td>33,3</td><td>38,2</td><td>42,7</td></tr>
<tr><td>35</td><td>120</td><td>12,1</td><td>14,1</td><td>15,9</td><td>17,5</td><td>19,0</td><td>20,4</td><td>23,0</td><td>25,3</td><td>27,5</td><td>32,3</td><td>37,3</td><td>42,9</td><td>47,9</td></tr>
<tr><td>36</td><td>160</td><td>13,6</td><td>15,9</td><td>17,9</td><td>19,7</td><td>21,3</td><td>22,9</td><td>25,8</td><td>28,4</td><td>30,8</td><td>36,2</td><td>41,9</td><td>48,1</td><td>53,7</td></tr>
<tr><td>37</td><td rowspan="6">3200</td><td>30</td><td>8,2</td><td>9,5</td><td>10,7</td><td>11,8</td><td>12,8</td><td>13,7</td><td>15,5</td><td>17,0</td><td>18,5</td><td>21,7</td><td>25,1</td><td>28,9</td><td>32,2</td></tr>
<tr><td>38</td><td>50</td><td>10,0</td><td>11,7</td><td>13,1</td><td>14,5</td><td>15,7</td><td>16,9</td><td>19,0</td><td>20,9</td><td>22,7</td><td>26,6</td><td>30,8</td><td>35,4</td><td>39,5</td></tr>
<tr><td>39</td><td>70</td><td>11,5</td><td>13,4</td><td>15,0</td><td>16,6</td><td>18,0</td><td>19,3</td><td>21,7</td><td>23,9</td><td>25,9</td><td>30,5</td><td>35,3</td><td>40,5</td><td>45,2</td></tr>
<tr><td>40</td><td>90</td><td>12,7</td><td>14,8</td><td>16,6</td><td>18,3</td><td>19,9</td><td>21,3</td><td>24,0</td><td>26,4</td><td>28,7</td><td>33,7</td><td>39,0</td><td>44,8</td><td>50,0</td></tr>
<tr><td>41</td><td>120</td><td>14,2</td><td>16,6</td><td>18,6</td><td>20,5</td><td>22,3</td><td>23,9</td><td>26,9</td><td>29,6</td><td>32,2</td><td>37,8</td><td>43,7</td><td>50,3</td><td>56,1</td></tr>
<tr><td>42</td><td>160</td><td>16,0</td><td>18,6</td><td>20,9</td><td>23,0</td><td>25,0</td><td>26,8</td><td>30,2</td><td>33,3</td><td>36,1</td><td>42,4</td><td>49,1</td><td>56,4</td><td>63,0</td></tr>
<tr><td></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в кольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 38, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td>Внутренний</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>диаметр кольца</td><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>43</td><td rowspan="6">4000</td><td>30</td><td>9,2</td><td>10,8</td><td>12,1</td><td>13,3</td><td>14,5</td><td>15,5</td><td>17,5</td><td>19,3</td><td>20,9</td><td>24,6</td><td>28,4</td><td>32,6</td><td>36,4</td></tr>
<tr><td>44</td><td>50</td><td>11,3</td><td>13,2</td><td>14,9</td><td>16,4</td><td>17,8</td><td>19,1</td><td>21,4</td><td>23,6</td><td>25,6</td><td>30,1</td><td>34,8</td><td>40,0</td><td>44,7</td></tr>
<tr><td>45</td><td>70</td><td>13,0</td><td>15,1</td><td>17,0</td><td>18,7</td><td>20,3</td><td>21,8</td><td>24,5</td><td>27,0</td><td>29,3</td><td>34,5</td><td>39,9</td><td>45,8</td><td>51,1</td></tr>
<tr><td>46</td><td>90</td><td>14,3</td><td>16,7</td><td>18,8</td><td>20,7</td><td>22,5</td><td>24,1</td><td>27,1</td><td>29,9</td><td>32,4</td><td>38,1</td><td>44,1</td><td>50,7</td><td>56,5</td></tr>
<tr><td>47</td><td>120</td><td>16,1</td><td>18,7</td><td>21,1</td><td>23,2</td><td>25,2</td><td>27,0</td><td>30,4</td><td>33,5</td><td>36,4</td><td>42,8</td><td>49,5</td><td>56,8</td><td>63,4</td></tr>
<tr><td>48</td><td>160</td><td>18,0</td><td>21,0</td><td>23,6</td><td>26,0</td><td>28,3</td><td>30,3</td><td>34,1</td><td>37,6</td><td>40,8</td><td>48,0</td><td>55,5</td><td>63,8</td><td>71,2</td></tr>
<tr><td>49</td><td rowspan="5">5000</td><td>50</td><td>-</td><td>-</td><td>16,8</td><td>18,5</td><td>20,1</td><td>21,5</td><td>24,2</td><td>26,7</td><td>29,0</td><td>34,1</td><td>39,4</td><td>45,3</td><td>50,5</td></tr>
<tr><td>50</td><td>70</td><td>-</td><td>-</td><td>19,2</td><td>21,2</td><td>23,0</td><td>24,6</td><td>27,7</td><td>30,5</td><td>33,1</td><td>39,0</td><td>45,1</td><td>51,8</td><td>57,8</td></tr>
<tr><td>51</td><td>90</td><td>-</td><td>-</td><td>21,2</td><td>23,4</td><td>25,4</td><td>27,2</td><td>30,7</td><td>33,8</td><td>36,7</td><td>43,1</td><td>49,8</td><td>57,3</td><td>63,9</td></tr>
<tr><td>52</td><td>120</td><td>-</td><td>-</td><td>23,8</td><td>26,2</td><td>28,5</td><td>30,6</td><td>34,4</td><td>37,9</td><td>41,1</td><td>48,3</td><td>55,9</td><td>64,3</td><td>71,7</td></tr>
<tr><td>53</td><td>160</td><td>-</td><td>-</td><td>26,7</td><td>29,4</td><td>32,0</td><td>34,3</td><td>38,6</td><td>42,5</td><td>46,1</td><td>54,2</td><td>62,7</td><td>72,1</td><td>80,5</td></tr>
<tr><td></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="8%"><col width="6%"><col width="6%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="7%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка полосовой стали на ребро в кольца в вальцах</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 38, лист 6</td></tr>
<tr><td rowspan="3">N позиции</td><td>Внутренний</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="14">Толщина полосы h, мм, до</td></tr>
<tr><td>диаметр кольца</td><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>54</td><td rowspan="5">6000</td><td>50</td><td>-</td><td>-</td><td>-</td><td>20,4</td><td>22,2</td><td>23,8</td><td>26,8</td><td>29,5</td><td>32,0</td><td colspan="2">37,7</td><td>43,6</td><td>50,0</td><td>55,9</td></tr>
<tr><td>55</td><td>70</td><td>-</td><td>-</td><td>-</td><td>23,4</td><td>25,4</td><td>27,2</td><td>30,7</td><td>33,8</td><td>36,6</td><td colspan="2">43,1</td><td>49,8</td><td>57,3</td><td>63,9</td></tr>
<tr><td>56</td><td>90</td><td>-</td><td>-</td><td>-</td><td>25,9</td><td>28,1</td><td>30,1</td><td>33,9</td><td>37,3</td><td>40,5</td><td colspan="2">47,6</td><td>55,1</td><td>63,3</td><td>70,7</td></tr>
<tr><td>57</td><td>120</td><td>-</td><td>-</td><td>-</td><td>29,0</td><td>31,5</td><td>33,8</td><td>38,0</td><td>41,9</td><td>46,5</td><td colspan="2">53,4</td><td>61,8</td><td>71,0</td><td>79,3</td></tr>
<tr><td>58</td><td>160</td><td>-</td><td>-</td><td>-</td><td>32,6</td><td>35,3</td><td>37,9</td><td>42,7</td><td>47,0</td><td>51,0</td><td colspan="2">60,0</td><td>69,3</td><td>79,7</td><td>89,0</td></tr>
<tr><td>59</td><td rowspan="5">7000</td><td>50</td><td>-</td><td>-</td><td>-</td><td>22,3</td><td>24,1</td><td>25,9</td><td>29,2</td><td>32,2</td><td>34,9</td><td colspan="2">41,0</td><td>47,4</td><td>54,5</td><td>60,8</td></tr>
<tr><td>60</td><td>70</td><td>-</td><td>-</td><td>-</td><td>25,5</td><td>27,6</td><td>29,7</td><td>33,4</td><td>36,8</td><td>39,9</td><td colspan="2">46,9</td><td>54,2</td><td>62,3</td><td>69,6</td></tr>
<tr><td>61</td><td>90</td><td>-</td><td>-</td><td>-</td><td>28,1</td><td>30,5</td><td>32,8</td><td>36,9</td><td>40,6</td><td>44,1</td><td colspan="2">51,8</td><td>60,0</td><td>70,0</td><td>76,9</td></tr>
<tr><td>62</td><td>120</td><td>-</td><td>-</td><td>-</td><td>31,6</td><td>34,3</td><td>36,8</td><td>41,4</td><td>45,6</td><td>49,5</td><td colspan="2">58,2</td><td>67,3</td><td>77,3</td><td>86,3</td></tr>
<tr><td>63</td><td>160</td><td>-</td><td>-</td><td>-</td><td>35,4</td><td>38,4</td><td>41,3</td><td>46,4</td><td>51,2</td><td>55,5</td><td colspan="2">65,3</td><td>75,5</td><td>86,7</td><td>96,8</td></tr>
<tr><td>64</td><td rowspan="5">8000</td><td>50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>26,0</td><td>27,9</td><td>31,4</td><td>34,6</td><td>37,5</td><td colspan="2">44,1</td><td>51,0</td><td>58,6</td><td>65,4</td></tr>
<tr><td>65</td><td>70</td><td>-</td><td>-</td><td>-</td><td>-</td><td>29,7</td><td>31,9</td><td>35,9</td><td>39,6</td><td>42,3</td><td colspan="2">50,5</td><td>58,4</td><td>67,1</td><td>74,9</td></tr>
<tr><td>66</td><td>90</td><td>-</td><td>-</td><td>-</td><td>-</td><td>32,9</td><td>35,3</td><td>39,7</td><td>43,7</td><td>47,5</td><td colspan="2">55,8</td><td>64,5</td><td>74,2</td><td>82,8</td></tr>
<tr><td>67</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td><td>36,9</td><td>39,6</td><td>44,6</td><td>49,1</td><td>53,2</td><td colspan="2">62,6</td><td>72,4</td><td>83,2</td><td>92,9</td></tr>
<tr><td>68</td><td>160</td><td>-</td><td>-</td><td>-</td><td>-</td><td>41,4</td><td>44,4</td><td>50,0</td><td>55,1</td><td>59,7</td><td colspan="2">70,2</td><td>81,2</td><td>93,4</td><td>104,2</td></tr>
<tr><td></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="6%"><col width="7%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка в вальцах полосовой стали на ребро в кольца</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 38, лист 7</td></tr>
<tr><td rowspan="3">N позиции</td><td>Внутренний</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="14">Толщина полосы h, мм, до</td></tr>
<tr><td>диаметр кольца</td><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td colspan="2">38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>69</td><td rowspan="5">9000</td><td>50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>27,7</td><td>29,8</td><td>33,5</td><td>36,9</td><td>40,0</td><td colspan="2">47,1</td><td>54,4</td><td>62,5</td><td>69,8</td></tr>
<tr><td>70</td><td>70</td><td>-</td><td>-</td><td>-</td><td>-</td><td>31,7</td><td>34,0</td><td>38,3</td><td>42,2</td><td>45,8</td><td colspan="2">53,8</td><td>62,3</td><td>71,6</td><td>79,9</td></tr>
<tr><td>71</td><td>90</td><td>-</td><td>-</td><td>-</td><td>-</td><td>35,1</td><td>37,6</td><td>42,4</td><td>46,7</td><td>50,6</td><td colspan="2">59,5</td><td>68,9</td><td>79,1</td><td>88,3</td></tr>
<tr><td>72</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td><td>39,3</td><td>42,2</td><td>47,5</td><td>52,4</td><td>56,8</td><td colspan="2">66,8</td><td>77,3</td><td>88,8</td><td>99,1</td></tr>
<tr><td>73</td><td>160</td><td>-</td><td>-</td><td>-</td><td>-</td><td>44,1</td><td>47,4</td><td>53,5</td><td>58,7</td><td>63,7</td><td colspan="2">74,9</td><td>86,7</td><td>99,6</td><td>111,2</td></tr>
<tr><td></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td></tr>
</table>


<a id="p102572"></a>Примечания: 1. При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="9%"><col width="9%"><col width="8%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="6%"><col width="8%"><col width="8%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="3">Материал</td><td colspan="4">Часть окружности кольца</td><td colspan="3">Скорость вращения валков, м/мин.</td></tr>
<tr><td>времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>полная окружность</td><td>3/4 окружности</td><td>1/3 окружности</td><td>1/4 окружности</td><td>до 6</td><td>7 - 8</td><td>св. 8</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,8</td><td>0,6</td><td>0,5</td><td>1,2</td><td>1,0</td><td>0,8</td></tr>
</table>


2. <a id="p102575"></a>Работа выполняется бригадой из двух человек:

                                  0,55    0,4    0,53
<a id="p102576"></a>                   Т = 0,00957 х Д     х В    х h    .


<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в полукольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 39, лист 1</td></tr>
<tr><td colspan="16">Содержание работы</td></tr>
<tr><td colspan="16">1. Подать полосу к вальцам.</td></tr>
<tr><td colspan="16">2. Заправить полосу в вальцы.</td></tr>
<tr><td colspan="16">3. Гнуть полосу на ребро в полукольцо.</td></tr>
<tr><td colspan="16">4. Проверить по диаметру шаблоном.</td></tr>
<tr><td colspan="16">5. Снять кольцо, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Внутренний диаметр полукольца</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="6">550</td><td>30</td><td>1,86</td><td>2,17</td><td>2,44</td><td>2,69</td><td>2,92</td><td>3,13</td><td>3,53</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>50</td><td>2,28</td><td>2,66</td><td>3,00</td><td>3,30</td><td>3,58</td><td>3,84</td><td>4,33</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>70</td><td>2,61</td><td>3,04</td><td>3,43</td><td>3,77</td><td>4,10</td><td>4,40</td><td>4,95</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>90</td><td>2,89</td><td>3,37</td><td>3,79</td><td>4,17</td><td>4,53</td><td>4,86</td><td>5,50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>120</td><td>3,24</td><td>3,78</td><td>4,25</td><td>4,68</td><td>5,10</td><td>5,50</td><td>6,10</td><td>6,8</td><td>7,3</td><td>8,6</td><td>10,0</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>160</td><td>3,64</td><td>4,24</td><td>4,77</td><td>5,25</td><td>5,70</td><td>6,10</td><td>6,90</td><td>7,6</td><td>8,2</td><td>9,7</td><td>11,2</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в полукольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 39, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Внутренний диаметр полукольца</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>7</td><td rowspan="6">750</td><td>30</td><td>2,21</td><td>2,57</td><td>2,90</td><td>3,19</td><td>3,46</td><td>3,7</td><td>4,1</td><td>4,6</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>50</td><td>2,71</td><td>3,16</td><td>3,55</td><td>3,91</td><td>4,25</td><td>4,5</td><td>5,1</td><td>5,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>70</td><td>3,10</td><td>3,61</td><td>4,06</td><td>4,48</td><td>4,86</td><td>5,2</td><td>5,8</td><td>6,4</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>90</td><td>3,43</td><td>3,99</td><td>4,49</td><td>4,95</td><td>5,40</td><td>5,8</td><td>6,5</td><td>7,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td>120</td><td>3,85</td><td>4,48</td><td>5,00</td><td>5,60</td><td>6,00</td><td>6,5</td><td>7,3</td><td>8,0</td><td>8,7</td><td>10,2</td><td>11,8</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>160</td><td>4,31</td><td>5,00</td><td>5,60</td><td>6,20</td><td>6,80</td><td>7,3</td><td>8,2</td><td>9,0</td><td>9,8</td><td>11,5</td><td>13,3</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td rowspan="6">1000</td><td>30</td><td>2,59</td><td>3,01</td><td>3,39</td><td>3,74</td><td>4,05</td><td>4,3</td><td>4,90</td><td>5,5</td><td>5,9</td><td>6,9</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td>50</td><td>3,17</td><td>3,70</td><td>4,16</td><td>4,58</td><td>4,97</td><td>5,3</td><td>6,0</td><td>6,1</td><td>7,1</td><td>8,4</td><td>-</td><td></td><td>-</td></tr>
<tr><td>15</td><td>70</td><td>3,63</td><td>4,23</td><td>4,76</td><td>5,20</td><td>5,70</td><td>6,1</td><td>6,9</td><td>7,6</td><td>8,2</td><td>9,7</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>90</td><td>4,02</td><td>4,68</td><td>5,30</td><td>5,80</td><td>6,30</td><td>6,8</td><td>7,6</td><td>8,4</td><td>9,1</td><td>10,7</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td>120</td><td>4,51</td><td>5,30</td><td>5,90</td><td>6,50</td><td>7,10</td><td>7,6</td><td>8,5</td><td>9,4</td><td>10,2</td><td>12,0</td><td>13,9</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td>160</td><td>5,10</td><td>5,90</td><td>6,60</td><td>7,30</td><td>7,90</td><td>8,5</td><td>9,6</td><td>10,5</td><td>11,4</td><td>13,5</td><td>15,6</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в полукольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 39, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Внутренний диаметр полукольца</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>19</td><td rowspan="6">1350</td><td>30</td><td>3,05</td><td>3,5</td><td>4,0</td><td>4,4</td><td>4,7</td><td>5,1</td><td>5,8</td><td>6,4</td><td>6,9</td><td>8,1</td><td>9,4</td><td>10,8</td><td>-</td></tr>
<tr><td>20</td><td>50</td><td>3,74</td><td>4,3</td><td>4,9</td><td>5,4</td><td>5,9</td><td>6,3</td><td>7,1</td><td>7,8</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,2</td><td>-</td></tr>
<tr><td>21</td><td>70</td><td>4,28</td><td>4,9</td><td>5,6</td><td>6,2</td><td>6,7</td><td>7,2</td><td>8,1</td><td>8,9</td><td>9,7</td><td>11,4</td><td>13,2</td><td>15,1</td><td>-</td></tr>
<tr><td>22</td><td>90</td><td>4,74</td><td>5,5</td><td>6,2</td><td>6,8</td><td>7,4</td><td>8,0</td><td>9,0</td><td>9,9</td><td>10,7</td><td>12,6</td><td>14,6</td><td>16,7</td><td>-</td></tr>
<tr><td>23</td><td>120</td><td>5,30</td><td>6,2</td><td>7,0</td><td>7,7</td><td>8,3</td><td>8,9</td><td>10,1</td><td>11,1</td><td>12,0</td><td>14,1</td><td>16,4</td><td>18,8</td><td>-</td></tr>
<tr><td>24</td><td>160</td><td>6,00</td><td>6,9</td><td>7,8</td><td>8,6</td><td>9,3</td><td>10,0</td><td>11,3</td><td>12,4</td><td>15,5</td><td>15,9</td><td>18,3</td><td>21,1</td><td>-</td></tr>
<tr><td>25</td><td rowspan="6">1800</td><td>30</td><td>3,58</td><td>4,1</td><td>4,6</td><td>5,2</td><td>5,6</td><td>6,0</td><td>6,8</td><td>7,5</td><td>8,1</td><td>9,5</td><td>11,0</td><td>12,6</td><td>14,1</td></tr>
<tr><td>26</td><td>50</td><td>4,39</td><td>5,1</td><td>5,8</td><td>6,3</td><td>6,9</td><td>7,4</td><td>8,3</td><td>9,1</td><td>9,9</td><td>11,7</td><td>13,5</td><td>15,5</td><td>17,3</td></tr>
<tr><td>27</td><td>70</td><td>5,00</td><td>5,8</td><td>6,6</td><td>7,3</td><td>7,9</td><td>8,4</td><td>9,5</td><td>10,5</td><td>11,4</td><td>13,4</td><td>15,4</td><td>17,7</td><td>19,8</td></tr>
<tr><td>28</td><td>90</td><td>5,60</td><td>6,5</td><td>7,3</td><td>8,0</td><td>8,7</td><td>9,3</td><td>10,5</td><td>11,6</td><td>12,6</td><td>14,8</td><td>17,1</td><td>19,6</td><td>21,9</td></tr>
<tr><td>29</td><td>120</td><td>6,20</td><td>7,3</td><td>8,2</td><td>9,0</td><td>9,8</td><td>10,5</td><td>11,8</td><td>13,0</td><td>14,1</td><td>16,6</td><td>19,2</td><td>22,0</td><td>24,6</td></tr>
<tr><td>30</td><td>160</td><td>7,00</td><td>8,1</td><td>9,2</td><td>10,1</td><td>10,9</td><td>11,8</td><td>13,2</td><td>14,6</td><td>15,8</td><td>18,6</td><td>21,5</td><td>24,6</td><td>27,6</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в полукольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 39, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Внутренний диаметр полукольца</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>31</td><td rowspan="6">2400</td><td>30</td><td>4,1</td><td>4,8</td><td>5,5</td><td>6,1</td><td>6,6</td><td>7,0</td><td>7,9</td><td>8,7</td><td>9,5</td><td>11,1</td><td>12,9</td><td>14,8</td><td>16,5</td></tr>
<tr><td>32</td><td>60</td><td>5,1</td><td>6,0</td><td>6,7</td><td>7,4</td><td>8,1</td><td>8,6</td><td>9,7</td><td>10,7</td><td>11,6</td><td>13,7</td><td>15,8</td><td>18,2</td><td>20,3</td></tr>
<tr><td>33</td><td>70</td><td>5,9</td><td>6,9</td><td>7,7</td><td>8,5</td><td>9,2</td><td>9,9</td><td>11,1</td><td>12,3</td><td>13,3</td><td>15,6</td><td>18,1</td><td>20,8</td><td>23,2</td></tr>
<tr><td>34</td><td>90</td><td>6,5</td><td>7,6</td><td>8,5</td><td>9,4</td><td>10,2</td><td>10,9</td><td>12,3</td><td>13,6</td><td>14,7</td><td>13,3</td><td>20,0</td><td>23,0</td><td>25,7</td></tr>
<tr><td>35</td><td>120</td><td>7,3</td><td>8,5</td><td>9,6</td><td>10,5</td><td>11,4</td><td>12,3</td><td>13,8</td><td>15,2</td><td>16,5</td><td>19,4</td><td>22,4</td><td>25,8</td><td>28,8</td></tr>
<tr><td>36</td><td>160</td><td>8,2</td><td>9,5</td><td>10,7</td><td>11,8</td><td>12,8</td><td>13,8</td><td>15,5</td><td>17,1</td><td>18,5</td><td>21,8</td><td>25,2</td><td>28,9</td><td>32,3</td></tr>
<tr><td>37</td><td rowspan="6">3200</td><td>30</td><td>4,9</td><td>5,7</td><td>6,4</td><td>7,1</td><td>7,7</td><td>8,3</td><td>9,3</td><td>10,2</td><td>11,1</td><td>13,1</td><td>15,1</td><td>17,4</td><td>19,4</td></tr>
<tr><td>38</td><td>50</td><td>6,0</td><td>7,0</td><td>7,9</td><td>8,7</td><td>9,4</td><td>10,1</td><td>11,4</td><td>12,6</td><td>13,6</td><td>16,0</td><td>18,5</td><td>21,3</td><td>23,8</td></tr>
<tr><td>39</td><td>70</td><td>6,9</td><td>8,0</td><td>9,0</td><td>9,9</td><td>10,8</td><td>11,6</td><td>13,0</td><td>14,1</td><td>15,6</td><td>18,3</td><td>21,2</td><td>24,4</td><td>27,2</td></tr>
<tr><td>40</td><td>90</td><td>7,6</td><td>8,9</td><td>10,0</td><td>11,0</td><td>11,9</td><td>12,8</td><td>14,4</td><td>15,9</td><td>17,2</td><td>20,3</td><td>23,4</td><td>26,9</td><td>30,1</td></tr>
<tr><td>41</td><td>120</td><td>8,5</td><td>10,0</td><td>11,2</td><td>12,3</td><td>13,4</td><td>14,4</td><td>16,2</td><td>17,8</td><td>19,3</td><td>22,7</td><td>26,3</td><td>30,2</td><td>33,7</td></tr>
<tr><td>42</td><td>160</td><td>9,6</td><td>11,2</td><td>12,6</td><td>13,8</td><td>15,0</td><td>16,1</td><td>18,1</td><td>20,0</td><td>21,7</td><td>25,5</td><td>29,5</td><td>23,9</td><td>37,8</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в полукольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 39, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Внутренний диаметр полукольца</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>43</td><td rowspan="6">4000</td><td>30</td><td>5,6</td><td>6,5</td><td>7,3</td><td>8,0</td><td>8,7</td><td>9,3</td><td>10,5</td><td>11,6</td><td>12,6</td><td>14,8</td><td>17,1</td><td>19,6</td><td>21,9</td></tr>
<tr><td>44</td><td>50</td><td>6,8</td><td>7,9</td><td>8,9</td><td>9,8</td><td>10,7</td><td>11,4</td><td>12,9</td><td>14,2</td><td>15,4</td><td>18,1</td><td>20,9</td><td>24,1</td><td>26,9</td></tr>
<tr><td>45</td><td>70</td><td>7,8</td><td>9,1</td><td>10,2</td><td>11,2</td><td>12,2</td><td>13,1</td><td>14,7</td><td>16,2</td><td>17,6</td><td>20,7</td><td>24,0</td><td>27,5</td><td>30,7</td></tr>
<tr><td>46</td><td>90</td><td>8,6</td><td>10,0</td><td>11,3</td><td>12,4</td><td>13,5</td><td>14,5</td><td>16,3</td><td>18,0</td><td>19,5</td><td>22,9</td><td>26,5</td><td>30,4</td><td>34,0</td></tr>
<tr><td>47</td><td>120</td><td>9,7</td><td>11,3</td><td>12,7</td><td>14,0</td><td>15,0</td><td>16,2</td><td>16,3</td><td>20,1</td><td>21,9</td><td>25,7</td><td>29,7</td><td>34,1</td><td>38,1</td></tr>
<tr><td>48</td><td>160</td><td>10,8</td><td>12,6</td><td>14,2</td><td>15,7</td><td>17,0</td><td>18,2</td><td>20,5</td><td>22,6</td><td>24,5</td><td>28,8</td><td>33,3</td><td>38,3</td><td>42,8</td></tr>
<tr><td>49</td><td rowspan="5">5000</td><td>50</td><td>-</td><td>-</td><td>10,1</td><td>11,1</td><td>12,1</td><td>12,9</td><td>14,6</td><td>16,0</td><td>17,4</td><td>20,5</td><td>23,7</td><td>27,2</td><td>30,4</td></tr>
<tr><td>50</td><td>70</td><td>-</td><td>-</td><td>11,5</td><td>12,7</td><td>13,8</td><td>14,8</td><td>16,7</td><td>18,4</td><td>19,9</td><td>23,4</td><td>27,1</td><td>31,1</td><td>34,7</td></tr>
<tr><td>51</td><td>90</td><td>-</td><td>-</td><td>12,8</td><td>14,1</td><td>15,3</td><td>16,4</td><td>18,4</td><td>20,3</td><td>22,0</td><td>25,9</td><td>29,9</td><td>34,4</td><td>38,4</td></tr>
<tr><td>52</td><td>120</td><td>-</td><td>-</td><td>14,3</td><td>15,8</td><td>17,1</td><td>18,4</td><td>20,7</td><td>22,8</td><td>24,7</td><td>29,0</td><td>33,6</td><td>38,6</td><td>43,1</td></tr>
<tr><td>53</td><td>160</td><td>-</td><td>-</td><td>16,1</td><td>17,7</td><td>19,2</td><td>20,6</td><td>23,2</td><td>25,5</td><td>27,7</td><td>32,6</td><td>37,7</td><td>43,3</td><td>48,4</td></tr>
<tr><td>54</td><td rowspan="3">6000</td><td>50</td><td>-</td><td>-</td><td>-</td><td>12,3</td><td>13,3</td><td>14,3</td><td>16,1</td><td>17,7</td><td>19,2</td><td>22,6</td><td>26,2</td><td>30,1</td><td>33,6</td></tr>
<tr><td>55</td><td>70</td><td>-</td><td>-</td><td>-</td><td>14,1</td><td>15,3</td><td>16,4</td><td>18,4</td><td>20,3</td><td>22,0</td><td>25,9</td><td>29,9</td><td>34,4</td><td>38,4</td></tr>
<tr><td>56</td><td>90</td><td>-</td><td>-</td><td>-</td><td>15,5</td><td>16,9</td><td>18,1</td><td>20,4</td><td>22,4</td><td>24,3</td><td>28,6</td><td>33,1</td><td>38,0</td><td>42,5</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в полукольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 39, лист 6</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Внутренний диаметр полукольца</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>57</td><td rowspan="2">6000</td><td>120</td><td>-</td><td>-</td><td>-</td><td>17,4</td><td>18,9</td><td>20,3</td><td>22,9</td><td>25,2</td><td>27,3</td><td>32,1</td><td>37,1</td><td>42,7</td><td>47,6</td></tr>
<tr><td>58</td><td>160</td><td>-</td><td>-</td><td>-</td><td>19,6</td><td>21,2</td><td>22,8</td><td>25,6</td><td>28,2</td><td>30,6</td><td>36,0</td><td>41,7</td><td>47,9</td><td>53,5</td></tr>
<tr><td>59</td><td rowspan="5">7000</td><td>50</td><td>-</td><td>-</td><td>-</td><td>13,4</td><td>14,5</td><td>15,6</td><td>17,5</td><td>19,3</td><td>20,9</td><td>24,6</td><td>28,5</td><td>32,7</td><td>36,5</td></tr>
<tr><td>60</td><td>70</td><td>-</td><td>-</td><td>-</td><td>15,3</td><td>16,6</td><td>16,8</td><td>20,1</td><td>22,1</td><td>24,0</td><td>28,2</td><td>32,6</td><td>37,4</td><td>41,8</td></tr>
<tr><td>61</td><td>90</td><td>-</td><td>-</td><td>-</td><td>16,9</td><td>18,4</td><td>19,7</td><td>22,2</td><td>24,4</td><td>26,5</td><td>31,2</td><td>36,0</td><td>41,4</td><td>46,2</td></tr>
<tr><td>62</td><td>120</td><td>-</td><td>-</td><td>-</td><td>19,0</td><td>20,6</td><td>22,1</td><td>24,9</td><td>27,4</td><td>29,7</td><td>34,9</td><td>40,4</td><td>46,5</td><td>51,9</td></tr>
<tr><td>63</td><td>160</td><td>-</td><td>-</td><td>-</td><td>21,3</td><td>23,1</td><td>24,8</td><td>27,9</td><td>30,7</td><td>33,4</td><td>39,2</td><td>45,4</td><td>52,1</td><td>58,2</td></tr>
<tr><td>64</td><td rowspan="5">8000</td><td>50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>15,6</td><td>16,8</td><td>18,9</td><td>20,8</td><td>22,5</td><td>26,5</td><td>30,7</td><td>35,2</td><td>39,3</td></tr>
<tr><td>65</td><td>70</td><td>-</td><td>-</td><td>-</td><td>-</td><td>17,9</td><td>19,2</td><td>21,6</td><td>23,8</td><td>25,8</td><td>30,3</td><td>35,1</td><td>40,3</td><td>45,0</td></tr>
<tr><td>66</td><td>90</td><td>-</td><td>-</td><td>-</td><td>-</td><td>19,8</td><td>21,2</td><td>23,9</td><td>26,3</td><td>28,5</td><td>33,5</td><td>38,8</td><td>44,6</td><td>49,7</td></tr>
<tr><td>67</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td><td>22,2</td><td>23,8</td><td>26,8</td><td>29,5</td><td>32,0</td><td>37,6</td><td>43,5</td><td>50,0</td><td>55,8</td></tr>
<tr><td>68</td><td>160</td><td>-</td><td>-</td><td>-</td><td>-</td><td>24,9</td><td>26,7</td><td>30,0</td><td>33,1</td><td>35,9</td><td>42,2</td><td>48,8</td><td>56,1</td><td>62,6</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16">Гибка полосовой стали на ребро в полукольца в вальцах Гибка</td></tr>
<tr><td colspan="16">Карта 39, лист 7</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Внутренний диаметр полукольца</td><td rowspan="3">Ширина заготовки (полосы) В, мм, до</td><td colspan="13">Толщина полосы h, мм, до</td></tr>
<tr><td>6</td><td>8</td><td>10</td><td>12</td><td>14</td><td>16</td><td>20</td><td>24</td><td>28</td><td>38</td><td>50</td><td>65</td><td>80</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>69</td><td rowspan="5">9000</td><td>50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>16,7</td><td>17,9</td><td>20,1</td><td>22,2</td><td>24,1</td><td>28,3</td><td>32,7</td><td>37,6</td><td>42,0</td></tr>
<tr><td>70</td><td>70</td><td>-</td><td>-</td><td>-</td><td>-</td><td>19,1</td><td>20,5</td><td>23,0</td><td>25,4</td><td>27,5</td><td>32,4</td><td>37,4</td><td>43,0</td><td>48,0</td></tr>
<tr><td>71</td><td>90</td><td>-</td><td>-</td><td>-</td><td>-</td><td>21,1</td><td>22,6</td><td>25,5</td><td>28,0</td><td>30,4</td><td>35,8</td><td>41,4</td><td>47,5</td><td>53,1</td></tr>
<tr><td>72</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td><td>23,6</td><td>25,4</td><td>28,6</td><td>31,4</td><td>34,1</td><td>40,1</td><td>46,4</td><td>53,3</td><td>59,5</td></tr>
<tr><td>73</td><td>160</td><td>-</td><td>-</td><td>-</td><td>-</td><td>26,5</td><td>28,5</td><td>32,0</td><td>35,3</td><td>38,3</td><td>45,0</td><td>52,1</td><td>59,8</td><td>66,8</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>


<a id="p102684"></a>Примечания: 1. При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="23%"><col width="18%"><col width="18%"><col width="11%"><col width="9%"><col width="11%"><col width="11%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="3">Материал</td><td colspan="3">Скорость вращения валков, м/мин.</td></tr>
<tr><td>времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>до 6</td><td>7 - 8</td><td>св. 8</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,2</td><td>1,0</td><td>0,8</td></tr>
</table>


2. <a id="p102687"></a>Работа выполняется бригадой из двух человек:

                                    0,55    0,4    0,53
<a id="p102688"></a>                     Т = 0,00575 х Д     х В    х h    .


<table>
<colgroup><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка заготовок из угловой стали в кольца и полукольца полкой наружу на трехвалковом станке</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 40, лист 1</td></tr>
<tr><td colspan="17">Содержание работы</td></tr>
<tr><td colspan="17">1. Подать заготовку к станку. (рисунок</td></tr>
<tr><td colspan="17">2. Гнуть заготовку в кольцо (полукольцо) полкой наружу. не приводится)</td></tr>
<tr><td colspan="17">3. Проверить диаметр по шаблону.</td></tr>
<tr><td colspan="17">4. Снять кольцо (полукольцо), отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид изделия</td><td rowspan="3">N профиля угловой стали</td><td>Толщина</td><td colspan="13">Диаметр кольца (полукольца) Д, мм, до</td></tr>
<tr><td>полки h,</td><td>550</td><td>750</td><td>1000</td><td>1350</td><td>1800</td><td>2400</td><td>3200</td><td>4000</td><td>5000</td><td>6000</td><td>7000</td><td>8000</td><td>9000</td></tr>
<tr><td>мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">К</td><td>2,5</td><td>4</td><td>2,1</td><td>2,6</td><td>3,2</td><td>4,1</td><td>5,1</td><td>6,5</td><td>8,1</td><td>9,6</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>3,2</td><td>4</td><td>2,3</td><td>2,9</td><td>3,6</td><td>4,6</td><td>5,7</td><td>7,2</td><td>9,0</td><td>10,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>4</td><td>5</td><td>2,8</td><td>3,6</td><td>4,5</td><td>5,7</td><td>7,2</td><td>9,0</td><td>11,3</td><td>13,4</td><td>16,0</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>о л</td><td>5</td><td>5</td><td>3,1</td><td>4,0</td><td>5,0</td><td>6,3</td><td>7,9</td><td>9,9</td><td>12,4</td><td>14,8</td><td>17,6</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>ь ц</td><td>6,3</td><td>6</td><td>3,9</td><td>4,9</td><td>6,2</td><td>7,8</td><td>9,9</td><td>12,2</td><td>15,3</td><td>18,2</td><td>21,7</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td rowspan="4">о</td><td rowspan="2">7</td><td>5</td><td>3,7</td><td>4,7</td><td>5,8</td><td>7,4</td><td>9,3</td><td>11,6</td><td>14,5</td><td>17,3</td><td>20,6</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>8</td><td>4,7</td><td>6,1</td><td>7,6</td><td>9,6</td><td>12,0</td><td>15,0</td><td>18,8</td><td>22,4</td><td>26,6</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td rowspan="2">7,5</td><td>6</td><td>4,2</td><td>5,3</td><td>6,7</td><td>8,4</td><td>10,6</td><td>13,2</td><td>16,6</td><td>19,7</td><td>23,4</td><td>27,6</td><td>30,5</td><td>33,9</td><td>37,1</td></tr>
<tr><td>9</td><td>9</td><td>5,2</td><td>6,7</td><td>8,4</td><td>10,6</td><td>13,2</td><td>17,5</td><td>20,7</td><td>24,6</td><td>29,3</td><td>33,8</td><td>38,1</td><td>42,3</td><td>46,4</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка заготовок из угловой стали в кольца и полукольца полкой наружу на трехвалковом станке</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 40, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид изделия</td><td rowspan="3">N профиля угловой стали</td><td>Толщина</td><td colspan="13">Диаметр кольца (полукольца) Д, мм, до</td></tr>
<tr><td>полки h,</td><td>550</td><td>750</td><td>1000</td><td>1350</td><td>1800</td><td>2400</td><td>3200</td><td>4000</td><td>5000</td><td>6000</td><td>7000</td><td>8000</td><td>9000</td></tr>
<tr><td>мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>10</td><td rowspan="5">К</td><td rowspan="2">8</td><td>6</td><td>4,3</td><td>5,5</td><td>6,9</td><td>8,7</td><td>10,9</td><td>13,6</td><td>17,1</td><td>20,3</td><td>24,1</td><td>27,8</td><td>31,4</td><td>34,9</td><td>38,2</td></tr>
<tr><td>11</td><td>8</td><td>5,1</td><td>6,4</td><td>8,1</td><td>10,2</td><td>12,8</td><td>15,9</td><td>20,0</td><td>23,8</td><td>28,3</td><td>32,6</td><td>36,8</td><td>40,8</td><td>44,8</td></tr>
<tr><td>12</td><td rowspan="2">9</td><td>7</td><td>5,0</td><td>6,3</td><td>7,9</td><td>10,0</td><td>12,5</td><td>15,6</td><td>19,6</td><td>23,3</td><td>27,7</td><td>31,9</td><td>36,1</td><td>40,0</td><td>43,8</td></tr>
<tr><td>13</td><td>9</td><td>5,7</td><td>7,2</td><td>9,1</td><td>11,4</td><td>14,3</td><td>17,9</td><td>22,4</td><td>26,7</td><td>31,8</td><td>36,6</td><td>41,3</td><td>45,8</td><td>50,3</td></tr>
<tr><td>14</td><td rowspan="3">10</td><td>8</td><td>5,6</td><td>7,1</td><td>8,9</td><td>11,3</td><td>14,1</td><td>17,6</td><td>22,1</td><td>26,3</td><td>31,2</td><td>36,1</td><td>40,7</td><td>45,1</td><td>49,5</td></tr>
<tr><td>15</td><td>о л</td><td>12</td><td>7,0</td><td>8,9</td><td>11,1</td><td>14,1</td><td>17,6</td><td>22,1</td><td>27,6</td><td>32,8</td><td>39,1</td><td>45,1</td><td>50,8</td><td>56,4</td><td>61,9</td></tr>
<tr><td>16</td><td>ь ц</td><td>16</td><td>8,2</td><td>10,4</td><td>13,0</td><td>16,5</td><td>20,6</td><td>25,8</td><td>32,3</td><td>38,5</td><td>45,8</td><td>52,8</td><td>59,5</td><td>66,0</td><td>72,4</td></tr>
<tr><td>17</td><td rowspan="6">о</td><td rowspan="3">12,5</td><td>9</td><td>6,6</td><td>8,4</td><td>10,5</td><td>13,3</td><td>16,6</td><td>20,8</td><td>26,1</td><td>31,0</td><td>36,9</td><td>42,5</td><td>48,0</td><td>53,2</td><td>58,4</td></tr>
<tr><td>18</td><td>12</td><td>7,7</td><td>9,8</td><td>12,3</td><td>15,5</td><td>19,5</td><td>24,4</td><td>30,5</td><td>36,3</td><td>43,2</td><td>49,8</td><td>56,2</td><td>62,4</td><td>68,4</td></tr>
<tr><td>19</td><td>16</td><td>9,0</td><td>11,5</td><td>14,4</td><td>18,2</td><td>22,8</td><td>28,5</td><td>35,7</td><td>42,5</td><td>50,6</td><td>58,3</td><td>65,8</td><td>73,0</td><td>80,0</td></tr>
<tr><td>20</td><td>14</td><td>16</td><td>9,5</td><td>12,1</td><td>15,1</td><td>19,2</td><td>24,0</td><td>30,0</td><td>37,6</td><td>44,7</td><td>53,2</td><td>61,4</td><td>69,2</td><td>76,8</td><td>84,2</td></tr>
<tr><td>21</td><td rowspan="2">20</td><td>12</td><td>9,6</td><td>12,2</td><td>15,2</td><td>19,2</td><td>24,1</td><td>30,1</td><td>37,7</td><td>44,9</td><td>53,4</td><td>61,6</td><td>69,5</td><td>77,1</td><td>84,5</td></tr>
<tr><td>22</td><td>20</td><td>12,6</td><td>16,1</td><td>20,1</td><td>25,5</td><td>31,9</td><td>39,9</td><td>49,9</td><td>59,4</td><td>70,8</td><td>81,5</td><td>92,0</td><td>102,1</td><td>112,0</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка заготовок из угловой стали в кольца и полукольца полкой наружу на трехвалковом станке</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 40, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид изделия</td><td rowspan="3">N профиля угловой стали</td><td>Толщина</td><td colspan="13">Диаметр кольца (полукольца) Д, мм, до</td></tr>
<tr><td>полосы h,</td><td>550</td><td>750</td><td>1000</td><td>1350</td><td>1800</td><td>2400</td><td>3200</td><td>4000</td><td>5000</td><td>6000</td><td>7000</td><td>8000</td><td>9000</td></tr>
<tr><td>мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>23</td><td rowspan="4">П</td><td>2,5</td><td>4</td><td>1,48</td><td>1,88</td><td>2,36</td><td>3,0</td><td>3,73</td><td>4,68</td><td>5,85</td><td>7,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>24</td><td>3,2</td><td>4</td><td>1,65</td><td>2,11</td><td>2,64</td><td>3,33</td><td>4,17</td><td>5,22</td><td>6,54</td><td>7,78</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>25</td><td>4</td><td>5</td><td>2,10</td><td>2,64</td><td>3,30</td><td>4,17</td><td>5,22</td><td>6,54</td><td>8,18</td><td>9,74</td><td>11,59</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>26</td><td>5</td><td>5</td><td>2,29</td><td>2,91</td><td>3,65</td><td>4,61</td><td>5,77</td><td>7,22</td><td>9,04</td><td>10,76</td><td>12,8</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>27</td><td>о л</td><td>6,3</td><td>6</td><td>2,8</td><td>3,6</td><td>4,5</td><td>5,7</td><td>7,1</td><td>8,9</td><td>11,1</td><td>13,2</td><td>15,7</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>23</td><td>у к</td><td rowspan="2">7</td><td>5</td><td>2,7</td><td>3,4</td><td>4,3</td><td>5,4</td><td>6,7</td><td>8,4</td><td>10,5</td><td>12,5</td><td>14,9</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>29</td><td>о л</td><td>8</td><td>3,4</td><td>4,4</td><td>5,5</td><td>6,9</td><td>8,7</td><td>10,9</td><td>13,6</td><td>16,2</td><td>19,3</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>30</td><td>ь ц</td><td rowspan="2">7,5</td><td>6</td><td>3,0</td><td>3,9</td><td>4,8</td><td>6,1</td><td>7,7</td><td>9,6</td><td>12,0</td><td>14,3</td><td>17,0</td><td>19,6</td><td>22,1</td><td>24,5</td><td>26,9</td></tr>
<tr><td>31</td><td rowspan="5">о</td><td>9</td><td>3,8</td><td>4,8</td><td>6,1</td><td>7,7</td><td>9,6</td><td>12,0</td><td>14,9</td><td>17,9</td><td>21,2</td><td>24,5</td><td>27,6</td><td>30,6</td><td>33,6</td></tr>
<tr><td>32</td><td rowspan="2">8</td><td>6</td><td>3,1</td><td>4,0</td><td>5,0</td><td>6,3</td><td>7,9</td><td>9,9</td><td>12,3</td><td>14,7</td><td>17,5</td><td>20,2</td><td>22,7</td><td>25,2</td><td>27,7</td></tr>
<tr><td>33</td><td>8</td><td>3,7</td><td>4,7</td><td>5,8</td><td>7,4</td><td>9,2</td><td>11,6</td><td>14,5</td><td>17,2</td><td>20,5</td><td>23,6</td><td>26,6</td><td>29,6</td><td>32,4</td></tr>
<tr><td>34</td><td rowspan="2">9</td><td>7</td><td>3,6</td><td>4,6</td><td>5,7</td><td>7,2</td><td>9,1</td><td>11,3</td><td>14,2</td><td>16,9</td><td>20,1</td><td>23,1</td><td>26,1</td><td>29,0</td><td>31,7</td></tr>
<tr><td>35</td><td>9</td><td>4,1</td><td>5,2</td><td>6,6</td><td>8,3</td><td>10,4</td><td>13,0</td><td>16,3</td><td>19,4</td><td>23,1</td><td>26,6</td><td>30,0</td><td>37,3</td><td>36,5</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка заготовок из угловой стали в кольца и полукольца полкой наружу на трехвалковом станке</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 40, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид изделия</td><td rowspan="3">N профиля угловой стали</td><td>Толщина</td><td colspan="13">Диаметр кольца (полукольца) Д, мм, до</td></tr>
<tr><td>полосы h,</td><td>550</td><td>750</td><td>1000</td><td>1350</td><td>1800</td><td>2400</td><td>3200</td><td>4000</td><td>5000</td><td>6000</td><td>7000</td><td>8000</td><td>9000</td></tr>
<tr><td>мм, до</td><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>36</td><td rowspan="2">П</td><td rowspan="3">10</td><td>8</td><td>4,1</td><td>6,1</td><td>6,4</td><td>8,1</td><td>10,2</td><td>12,8</td><td>16,0</td><td>19,0</td><td>22,6</td><td>26,1</td><td>29,4</td><td>32,7</td><td>35,8</td></tr>
<tr><td>37</td><td>12</td><td>5,1</td><td>6,4</td><td>8,1</td><td>10,2</td><td>12,8</td><td>16,0</td><td>20,0</td><td>23,8</td><td>28,3</td><td>32,6</td><td>36,8</td><td>40,9</td><td>44,8</td></tr>
<tr><td>38</td><td>о л</td><td>16</td><td>5,9</td><td>7,5</td><td>9,4</td><td>11,9</td><td>14,9</td><td>18,7</td><td>23,4</td><td>27,8</td><td>33,1</td><td>38,2</td><td>43,1</td><td>47,8</td><td>52,4</td></tr>
<tr><td>39</td><td>у к</td><td rowspan="3">12,5</td><td>9</td><td>4,8</td><td>6,1</td><td>7,6</td><td>9,6</td><td>12,1</td><td>15,1</td><td>18,9</td><td>22,4</td><td>26,7</td><td>30,8</td><td>34,7</td><td>38,5</td><td>42,3</td></tr>
<tr><td>40</td><td>о л</td><td>12</td><td>5,6</td><td>7,1</td><td>8,9</td><td>11,3</td><td>14,1</td><td>17,7</td><td>22,1</td><td>26,3</td><td>31,3</td><td>36,1</td><td>40,7</td><td>45,2</td><td>49,5</td></tr>
<tr><td>41</td><td>ь ц</td><td>16</td><td>6,6</td><td>8,3</td><td>10,1</td><td>13,2</td><td>16,5</td><td>20,7</td><td>25,9</td><td>30,8</td><td>36,6</td><td>42,2</td><td>47,6</td><td>52,9</td><td>57,9</td></tr>
<tr><td>42</td><td rowspan="3">о</td><td>14</td><td>16</td><td>6,9</td><td>8,8</td><td>11,0</td><td>13,9</td><td>17,4</td><td>21,7</td><td>27,2</td><td>32,4</td><td>38,5</td><td>44,4</td><td>50,1</td><td>55,6</td><td>60,9</td></tr>
<tr><td>43</td><td rowspan="2">20</td><td>12</td><td>6,9</td><td>8,8</td><td>11,0</td><td>13,9</td><td>17,4</td><td>21,8</td><td>27,3</td><td>32,5</td><td>38,7</td><td>44,6</td><td>50,3</td><td>55,8</td><td>61,2</td></tr>
<tr><td>44</td><td>20</td><td>9,2</td><td>11,7</td><td>14,6</td><td>18,5</td><td>23,1</td><td>28,9</td><td>36,2</td><td>43,0</td><td>51,2</td><td>59,1</td><td>66,6</td><td>73,9</td><td>81,0</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>


<a id="p102754"></a>Примечания:
1. <a id="p102755"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="76%"><col width="24%"></colgroup>
<tr><td rowspan="2">Гибка заготовок из угловой стали в кольца и полукольца полкой наружу на трехвалковом станке</td><td>Гибка</td></tr>
<tr><td>Карта 40, лист 5</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"><col width="15%"><col width="15%"><col width="15%"></colgroup>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="4">Часть окружности кольца</td></tr>
<tr><td>на изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>полная окружность</td><td>3/4 окружности</td><td>1/3 окружности</td><td>1/4 окружности</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,8</td><td>0,6</td><td>0,5</td></tr>
</table>


2. <a id="p102760"></a>Работа выполняется бригадой из двух человек:

                           0,45    0,55    0,78
<a id="p102761"></a>            Т = 0,00461 х N     х h     х Д       поз. 1...22;

                            0,45    0,55    0,78
<a id="p102762"></a>            Т = 0,003337 х N     х h     х Д      поз. 23...44.


<table>
<colgroup><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка заготовок из угловой стали в кольца и полукольца полкой внутрь на трехвалковом станке</td><td colspan="5">Гибка</td></tr>
<tr><td colspan="5">Карта 41, лист 1</td></tr>
<tr><td colspan="18">Содержание работы</td></tr>
<tr><td colspan="18">1. Подать заготовку к станку. (рисунок не</td></tr>
<tr><td colspan="18">2. Гнуть заготовку в кольцо (полукольцо) полкой внутрь. приводится)</td></tr>
<tr><td colspan="18">3. Проверить диаметр по шаблону.</td></tr>
<tr><td colspan="18">4. Снять кольцо (полукольцо), отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид изделия</td><td rowspan="3">N профиля угловой стали</td><td>Толщина</td><td colspan="14">Диаметр кольца (полукольца) Д, мм, до</td></tr>
<tr><td>полки h,</td><td>550</td><td>750</td><td>1000</td><td>1350</td><td>1800</td><td>2400</td><td>3200</td><td>4000</td><td colspan="2">5000</td><td>6000</td><td>7000</td><td>8000</td><td>9000</td></tr>
<tr><td>мм, до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">К</td><td>2,5</td><td>4</td><td>2,5</td><td>3,1</td><td>3,9</td><td>5,0</td><td>6,2</td><td>7,8</td><td>9,7</td><td>11,6</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>3,2</td><td>4</td><td>2,8</td><td>3,5</td><td>4,4</td><td>5,5</td><td>6,9</td><td>8,7</td><td>10,9</td><td>12,9</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>4</td><td>5</td><td>3,4</td><td>4,4</td><td>5,5</td><td>6,9</td><td>8,7</td><td>10,9</td><td>13,6</td><td>16,2</td><td colspan="2">19</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>о л</td><td>5</td><td>5</td><td>3,8</td><td>4,8</td><td>6,1</td><td>7,7</td><td>9,6</td><td>12,0</td><td>15,0</td><td>17,9</td><td colspan="2">21</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>ь ц</td><td>6,3</td><td>6</td><td>4,7</td><td>5,9</td><td>7,4</td><td>9,4</td><td>11,8</td><td>14,7</td><td>18,4</td><td>22,0</td><td colspan="2">26</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td rowspan="4">о</td><td rowspan="2">7</td><td>5</td><td>4,4</td><td>5,6</td><td>7,1</td><td>8,9</td><td>11,2</td><td>14,0</td><td>17,5</td><td>21,0</td><td colspan="2">25</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>8</td><td>5,7</td><td>7,3</td><td>9,1</td><td>11,6</td><td>14,5</td><td>18,1</td><td>23,0</td><td>27,0</td><td colspan="2">32</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td rowspan="2">7,5</td><td>6</td><td>5,0</td><td>6,4</td><td>8,1</td><td>10,2</td><td>12,7</td><td>15,9</td><td>20,0</td><td>24,0</td><td colspan="2">28</td><td>33</td><td>37</td><td>41</td><td>45</td></tr>
<tr><td>9</td><td>9</td><td>6,3</td><td>8,0</td><td>10,1</td><td>12,7</td><td>15,9</td><td>20,0</td><td>25,0</td><td>30,0</td><td colspan="2">35</td><td>41</td><td>46</td><td>51</td><td>56</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка заготовок из угловой стали в кольца и полукольца полкой внутрь на трехвалковом станке</td><td colspan="5">Гибка</td></tr>
<tr><td colspan="5">Карта 41, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид изделия</td><td rowspan="3">N профиля угловой стали</td><td>Толщина</td><td colspan="14">Диаметр кольца (полукольца) Д, мм, до</td></tr>
<tr><td>полки h,</td><td>550</td><td>750</td><td>1000</td><td>1350</td><td>1800</td><td>2400</td><td>3200</td><td>4000</td><td colspan="2">5000</td><td>6000</td><td>7000</td><td>8000</td><td>9000</td></tr>
<tr><td>мм, до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>10</td><td rowspan="2">К</td><td rowspan="2">8</td><td>6</td><td>5,2</td><td>6,6</td><td>8,3</td><td>10,5</td><td>13,1</td><td>16</td><td>21</td><td>24</td><td colspan="2">29</td><td>34</td><td>38</td><td>42</td><td>46</td></tr>
<tr><td>11</td><td>8</td><td>6,1</td><td>7,8</td><td>9,7</td><td>12,3</td><td>15,4</td><td>19</td><td>24</td><td>29</td><td colspan="2">34</td><td>39</td><td>44</td><td>49</td><td>54</td></tr>
<tr><td>12</td><td>о л</td><td rowspan="2">9</td><td>7</td><td>6,0</td><td>7,6</td><td>9,5</td><td>12,0</td><td>15,0</td><td>18</td><td>24</td><td>28</td><td colspan="2">33</td><td>38</td><td>48</td><td>43</td><td>53</td></tr>
<tr><td>13</td><td>ь ц</td><td>9</td><td>6,8</td><td>8,7</td><td>10,9</td><td>13,8</td><td>17,3</td><td>22</td><td>27</td><td>32</td><td colspan="2">38</td><td>44</td><td>50</td><td>55</td><td>61</td></tr>
<tr><td>14</td><td rowspan="9">о</td><td rowspan="3">10</td><td>8</td><td>6,7</td><td>8,6</td><td>10,7</td><td>13,6</td><td>17,0</td><td>21</td><td>27</td><td>32</td><td colspan="2">38</td><td>43</td><td>49</td><td>54</td><td>60</td></tr>
<tr><td>15</td><td>12</td><td>8,4</td><td>10,7</td><td>13,4</td><td>17,0</td><td>21,0</td><td>27</td><td>33</td><td>40</td><td colspan="2">47</td><td>54</td><td>61</td><td>68</td><td>74</td></tr>
<tr><td>16</td><td>16</td><td>9,8</td><td>12,5</td><td>15,7</td><td>19,8</td><td>25,0</td><td>31</td><td>39</td><td>46</td><td colspan="2">55</td><td>64</td><td>72</td><td>80</td><td>87</td></tr>
<tr><td>17</td><td rowspan="3">12,5</td><td>9</td><td>7,9</td><td>10,1</td><td>12,7</td><td>16,0</td><td>20,0</td><td>25</td><td>31</td><td>37</td><td colspan="2">44</td><td>51</td><td>58</td><td>64</td><td>70</td></tr>
<tr><td>18</td><td>12</td><td>9,3</td><td>11,9</td><td>14,8</td><td>18,7</td><td>23,0</td><td>29</td><td>37</td><td>44</td><td colspan="2">52</td><td>60</td><td>68</td><td>75</td><td>82</td></tr>
<tr><td>19</td><td>16</td><td>10,9</td><td>13,9</td><td>17,4</td><td>22,0</td><td>27,0</td><td>34</td><td>43</td><td>51</td><td colspan="2">61</td><td>70</td><td>79</td><td>83</td><td>96</td></tr>
<tr><td>20</td><td>14</td><td>16</td><td>11,5</td><td>14,6</td><td>18,3</td><td>23,0</td><td>29,0</td><td>36</td><td>45</td><td>54</td><td colspan="2">64</td><td>74</td><td>88</td><td>93</td><td>107</td></tr>
<tr><td>21</td><td rowspan="2">20</td><td>12</td><td>11,5</td><td>14,6</td><td>18,3</td><td>23,0</td><td>29,0</td><td>36</td><td>45</td><td>54</td><td colspan="2">64</td><td>74</td><td>84</td><td>93</td><td>102</td></tr>
<tr><td>22</td><td>20</td><td>15,2</td><td>19,4</td><td>24,0</td><td>31,0</td><td>38,0</td><td>48</td><td>60</td><td>72</td><td colspan="2">85</td><td>98</td><td>111</td><td>123</td><td>135</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка заготовок из угловой стали в кольца и полукольца полкой внутрь на трехвалковом станке</td><td colspan="5">Гибка</td></tr>
<tr><td colspan="5">Карта 41, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид изделия</td><td rowspan="3">N профиля угловой стали</td><td>Толщина</td><td colspan="14">Диаметр кольца (полукольца) Д, мм, до</td></tr>
<tr><td>полки h,</td><td>550</td><td>750</td><td>1000</td><td>1350</td><td>1800</td><td>2400</td><td>3200</td><td>4000</td><td colspan="2">5000</td><td>6000</td><td>7000</td><td>8000</td><td>9000</td></tr>
<tr><td>мм, до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>23</td><td rowspan="6">П о</td><td>2,5</td><td>4</td><td>1,6</td><td>2,0</td><td>2,5</td><td>3,1</td><td>3,9</td><td>4,9</td><td>6,1</td><td>7,3</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>24</td><td>3,2</td><td>4</td><td>1,7</td><td>2,2</td><td>2,7</td><td>3,5</td><td>4,4</td><td>5,4</td><td>6,8</td><td>8,1</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>25</td><td>4</td><td>5</td><td>2,2</td><td>2,7</td><td>3,4</td><td>4,3</td><td>5,4</td><td>6,8</td><td>8,5</td><td>10,1</td><td colspan="2">12,1</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>26</td><td>5</td><td>5</td><td>2,4</td><td>3,0</td><td>3,8</td><td>4,8</td><td>6,0</td><td>7,5</td><td>9,4</td><td>11,2</td><td colspan="2">13,4</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>27</td><td>6,3</td><td>6</td><td>2,9</td><td>3,7</td><td>4,7</td><td>5,9</td><td>7,4</td><td>9,2</td><td>11,6</td><td>13,8</td><td colspan="2">16,4</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>28</td><td rowspan="2">7</td><td>5</td><td>2,8</td><td>3,5</td><td>4,4</td><td>5,6</td><td>7,0</td><td>8,8</td><td>11,0</td><td>13,1</td><td colspan="2">15,5</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>29</td><td>л у</td><td>8</td><td>3,6</td><td>4,6</td><td>5,7</td><td>7,2</td><td>9,0</td><td>11,3</td><td>14,2</td><td>16,9</td><td colspan="2">20,0</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>30</td><td>к о</td><td rowspan="2">7,5</td><td>6</td><td>3,2</td><td>4,0</td><td>5,0</td><td>6,4</td><td>8,0</td><td>10,0</td><td>12,5</td><td>14,9</td><td colspan="2">17,7</td><td>20</td><td>23</td><td>26</td><td>28</td></tr>
<tr><td>31</td><td>л ь</td><td>9</td><td>4,0</td><td>5,0</td><td>6,3</td><td>8,0</td><td>10,0</td><td>12,5</td><td>15,6</td><td>18,6</td><td colspan="2">22,0</td><td>26</td><td>29</td><td>32</td><td>35</td></tr>
<tr><td>32</td><td rowspan="7">ц о</td><td rowspan="2">8</td><td>6</td><td>3,3</td><td>4,1</td><td>5,2</td><td>6,6</td><td>8,2</td><td>10,3</td><td>12,9</td><td>15,3</td><td colspan="2">18,2</td><td>21</td><td>24</td><td>26</td><td>29</td></tr>
<tr><td>33</td><td>8</td><td>3,8</td><td>4,9</td><td>6,1</td><td>7,7</td><td>9,6</td><td>12,1</td><td>15,1</td><td>18,0</td><td colspan="2">21,0</td><td>25</td><td>28</td><td>31</td><td>34</td></tr>
<tr><td>34</td><td rowspan="2">9</td><td>7</td><td>3,7</td><td>4,8</td><td>6,0</td><td>7,5</td><td>9,4</td><td>11,8</td><td>14,8</td><td>17,6</td><td colspan="2">21,0</td><td>24</td><td>27</td><td>30</td><td>33</td></tr>
<tr><td>35</td><td>9</td><td>4,3</td><td>5,5</td><td>6,8</td><td>8,6</td><td>10,8</td><td>13,6</td><td>17,0</td><td>20,0</td><td colspan="2">24,0</td><td>28</td><td>31</td><td>35</td><td>38</td></tr>
<tr><td>36</td><td rowspan="3">10</td><td>8</td><td>4,2</td><td>5,4</td><td>6,7</td><td>8,5</td><td>10,6</td><td>13,3</td><td>16,7</td><td>19,8</td><td colspan="2">24,0</td><td>27</td><td>31</td><td>34</td><td>37</td></tr>
<tr><td>37</td><td>12</td><td>5,3</td><td>6,7</td><td>8,4</td><td>10,6</td><td>13,3</td><td>16,7</td><td>21,0</td><td>25,0</td><td colspan="2">29,0</td><td>34</td><td>38</td><td>43</td><td>47</td></tr>
<tr><td>38</td><td>16</td><td>6,2</td><td>7,9</td><td>9,8</td><td>12,4</td><td>15,6</td><td>19,5</td><td>24,0</td><td>29,0</td><td colspan="2">35,0</td><td>40</td><td>45</td><td>50</td><td>55</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="13" rowspan="2">Гибка заготовок из угловой стали в кольца и полукольца полкой внутрь на трехвалковом станке</td><td colspan="5">Гибка</td></tr>
<tr><td colspan="5">Карта 41, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид изделия</td><td rowspan="3">N профиля угловой стали</td><td>Толщина</td><td colspan="14">Диаметр кольца (полукольца) Д, мм, до</td></tr>
<tr><td>полки h,</td><td>550</td><td>750</td><td>1000</td><td>1350</td><td>1800</td><td>2400</td><td>3200</td><td>4000</td><td colspan="2">5000</td><td>6000</td><td>7000</td><td>8000</td><td>9000</td></tr>
<tr><td>мм, до</td><td colspan="14">Время Т, чел.-мин.</td></tr>
<tr><td>39</td><td>П о</td><td rowspan="3">12,5</td><td>9</td><td>5,0</td><td>6,3</td><td>7,9</td><td>10,0</td><td>12,6</td><td>15,7</td><td>19</td><td>23</td><td colspan="2">28</td><td>32</td><td>36</td><td>40</td><td>44</td></tr>
<tr><td>40</td><td>л у</td><td>12</td><td>5,8</td><td>7,4</td><td>9,3</td><td>11,8</td><td>14,7</td><td>18,4</td><td>23</td><td>27</td><td colspan="2">33</td><td>38</td><td>42</td><td>47</td><td>52</td></tr>
<tr><td>41</td><td>к о</td><td>16</td><td>8,8</td><td>8,7</td><td>10,9</td><td>13,8</td><td>17,2</td><td>22,0</td><td>27</td><td>32</td><td colspan="2">38</td><td>44</td><td>50</td><td>55</td><td>60</td></tr>
<tr><td>42</td><td>л ь</td><td>14</td><td>16</td><td>7,2</td><td>9,2</td><td>11,5</td><td>14,5</td><td>18,1</td><td>23,0</td><td>28</td><td>34</td><td colspan="2">40</td><td>46</td><td>52</td><td>58</td><td>64</td></tr>
<tr><td>43</td><td rowspan="2">ц о</td><td rowspan="2">20</td><td>12</td><td>7,2</td><td>9,2</td><td>11,5</td><td>14,5</td><td>18,2</td><td>23,0</td><td>28</td><td>34</td><td colspan="2">40</td><td>47</td><td>52</td><td>58</td><td>64</td></tr>
<tr><td>44</td><td>20</td><td>9,5</td><td>12,2</td><td>15,2</td><td>19,2</td><td>24,0</td><td>30,0</td><td>38</td><td>45</td><td colspan="2">53</td><td>62</td><td>69</td><td>77</td><td>85</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>


<a id="p102828"></a>Примечания:
1. <a id="p102829"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="22%"><col width="18%"><col width="18%"><col width="11%"><col width="16%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="3">Материал</td><td colspan="4">Часть окружности кольца</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>полная окружность</td><td>3/4</td><td>1/3</td><td>1/4</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,8</td><td>0,6</td><td>0,5</td></tr>
</table>


2. <a id="p102832"></a>Работа выполняется бригадой из двух человек:

                           0,45    0,55    0,78
<a id="p102833"></a>            Т = 0,00555 х N     х h     х Д       поз. 1...22;

                           0,45    0,55    0,78
<a id="p102834"></a>            Т = 0,00348 х N     х h     х Д       поз. 23...44.


<table>
<colgroup><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="19">Наполнение труб песком вручную Гибка</td></tr>
<tr><td colspan="19">Карта 42, лист 1</td></tr>
<tr><td colspan="19">Содержание работы</td></tr>
<tr><td colspan="19">1. Установить трубу.</td></tr>
<tr><td colspan="19">2. Заглушить конец трубы пробкой.</td></tr>
<tr><td colspan="19">3. Взять ковш, наполнить трубу песком, утрамбовать с помощью молотка и досыпать песком.</td></tr>
<tr><td colspan="19">4. Заглушить второй конец трубы.</td></tr>
<tr><td colspan="19">5. Отложить трубу.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина трубы</td><td colspan="17">Наружный диаметр трубы Д, мм, до</td></tr>
<tr><td rowspan="2">L, м, до</td><td>12</td><td>16</td><td>20</td><td>25</td><td>32</td><td>42</td><td>50</td><td>63</td><td>83</td><td>102</td><td>121</td><td>140</td><td>159</td><td>194</td><td>245</td><td>325</td><td>426</td></tr>
<tr><td colspan="17">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>0,6</td><td>0,58</td><td>0,71</td><td>0,84</td><td>0,98</td><td>1,18</td><td>1,46</td><td>1,71</td><td>2,13</td><td>2,77</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>0,8</td><td>0,70</td><td>0,86</td><td>1,01</td><td>1,18</td><td>1,42</td><td>1,75</td><td>2,06</td><td>2,56</td><td>3,32</td><td>4,04</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>1,1</td><td>0,86</td><td>1,05</td><td>1,23</td><td>1,45</td><td>1,73</td><td>2,15</td><td>2,53</td><td>3,15</td><td>4,08</td><td>4,95</td><td>5,81</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>1,5</td><td>1,05</td><td>1,28</td><td>1,51</td><td>1,71</td><td>2,12</td><td>2,62</td><td>3,09</td><td>3,84</td><td>4,97</td><td>6,04</td><td>7,09</td><td>8,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>2,0</td><td>1,26</td><td>1,55</td><td>1,80</td><td>2,13</td><td>2,54</td><td>3,15</td><td>3,71</td><td>4,61</td><td>5,98</td><td>7,26</td><td>8,52</td><td>9,78</td><td>11,02</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>2,7</td><td>1,52</td><td>1,87</td><td>2,2</td><td>2,58</td><td>3,10</td><td>3,82</td><td>4,49</td><td>5,59</td><td>7,24</td><td>8,79</td><td>10,32</td><td>11,84</td><td>13,85</td><td>16,09</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>3,6</td><td>1,83</td><td>2,25</td><td>2,65</td><td>3,11</td><td>3,71</td><td>4,59</td><td>5,41</td><td>6,72</td><td>8,71</td><td>10,58</td><td>12,42</td><td>14,25</td><td>16,06</td><td>19,36</td><td>24,11</td><td>-</td><td>-</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="19">Наполнение труб песком вручную Гибка</td></tr>
<tr><td colspan="19">Карта 42, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина трубы</td><td colspan="17">Наружный диаметр трубы Д, мм, до</td></tr>
<tr><td rowspan="2">L, м, до</td><td>12</td><td>16</td><td>20</td><td>25</td><td>32</td><td>42</td><td>50</td><td>63</td><td>83</td><td>102</td><td>121</td><td>140</td><td>159</td><td>194</td><td>245</td><td>325</td><td>426</td></tr>
<tr><td colspan="17">Время Т, чел.-мин.</td></tr>
<tr><td>8</td><td>4,8</td><td>-</td><td>-</td><td>3,18</td><td>3,74</td><td>4,46</td><td>5,52</td><td>6,50</td><td>8,08</td><td>10,47</td><td>12,71</td><td>14,92</td><td>17,12</td><td>19,29</td><td>23,26</td><td>28,97</td><td>37,78</td><td>48,73</td></tr>
<tr><td>9</td><td>6,5</td><td>-</td><td>-</td><td>-</td><td>4,89</td><td>5,84</td><td>6,80</td><td>8,04</td><td>10,00</td><td>12,94</td><td>15,71</td><td>18,45</td><td>21,16</td><td>23,85</td><td>28,75</td><td>35,80</td><td>46,69</td><td>60,22</td></tr>
<tr><td>10</td><td>8,8</td><td>-</td><td>-</td><td>-</td><td>6,50</td><td>7,70</td><td>9,07</td><td>10,68</td><td>13,28</td><td>17,21</td><td>20,88</td><td>24,53</td><td>28,13</td><td>31,71</td><td>38,18</td><td>47,61</td><td>62,09</td><td>80,07</td></tr>
<tr><td>11</td><td>12,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>10,4</td><td>12,04</td><td>14,30</td><td>17,77</td><td>23,03</td><td>27,96</td><td>32,83</td><td>37,65</td><td>42,44</td><td>51,17</td><td>63,72</td><td>83,11</td><td>107,20</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td></tr>
</table>


<a id="p102860"></a>*Примечание.* Работа выполняется одним человеком при L <= 1,5 м и бригадой из двух человек при L > 1,5 м:

                 0,64    0,72
<a id="p102861"></a>    Т = 0,135 х L     х Д       при L <= 4,8 м  и Д <= 32 мм   поз. 1...8;

                 0,94    0,72
<a id="p102862"></a>    Т = 0,083 х L     х Д       при L > 4,8 м   и Д <= 32 мм   поз. 9...11;

                  0,64    0,94
<a id="p102863"></a>    Т = 0,0603 х L     х Д      при L <= 4,8 м  и Д > 32 мм    поз. 1...8;

                 0,94    0,94
<a id="p102864"></a>    Т = 0,035 х L     х Д       при L > 4,8 м   и Д > 32 мм    поз. 9...11.


<table>
<colgroup><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16" rowspan="2">Выбивка песка из труб</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 43, лист 1</td></tr>
<tr><td colspan="19">Содержание работы</td></tr>
<tr><td colspan="19">1. Установить трубу.</td></tr>
<tr><td colspan="19">2. Удалить пробки.</td></tr>
<tr><td colspan="19">3. Удалить песок.</td></tr>
<tr><td colspan="19">4. Отложить трубу.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина трубы</td><td colspan="17">Наружный диаметр трубы Д, мм, до</td></tr>
<tr><td rowspan="2">L, м, до</td><td>12</td><td>16</td><td>20</td><td>25</td><td>32</td><td>42</td><td>50</td><td>63</td><td>83</td><td>102</td><td>121</td><td>140</td><td>159</td><td>194</td><td>245</td><td>325</td><td>426</td></tr>
<tr><td colspan="17">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>0,6</td><td>0,61</td><td>0,54</td><td>0,49</td><td>0,54</td><td>0,61</td><td>0,70</td><td>0,76</td><td>0,85</td><td>0,98</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>0,8</td><td>0,76</td><td>0,67</td><td>0,61</td><td>0,67</td><td>0,76</td><td>0,87</td><td>0,95</td><td>1,07</td><td>1,23</td><td>1,36</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>1,1</td><td>0,97</td><td>0,86</td><td>0,78</td><td>0,86</td><td>0,97</td><td>1,11</td><td>1,22</td><td>1,36</td><td>1,56</td><td>1,74</td><td>1,89</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>1,5</td><td>1,23</td><td>1,10</td><td>1,00</td><td>1,09</td><td>1,23</td><td>1,41</td><td>1,54</td><td>1,73</td><td>1,99</td><td>2,21</td><td>2,40</td><td>2,58</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>2,0</td><td>1,54</td><td>1,36</td><td>1,25</td><td>1,36</td><td>1,54</td><td>1,76</td><td>1,93</td><td>2,16</td><td>2,48</td><td>2,75</td><td>3,00</td><td>3,22</td><td>3,43</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>2,7</td><td>1,94</td><td>1,72</td><td>1,57</td><td>1,72</td><td>1,94</td><td>2,22</td><td>2,42</td><td>2,72</td><td>3,13</td><td>3,48</td><td>3,78</td><td>4,06</td><td>4,33</td><td>4,78</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>3,6</td><td>2,42</td><td>2,15</td><td>1,96</td><td>2,14</td><td>2,42</td><td>2,78</td><td>3,03</td><td>3,40</td><td>3,91</td><td>4,33</td><td>4,72</td><td>5,08</td><td>5,41</td><td>5,97</td><td>6,71</td><td>-</td><td>-</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="16" rowspan="2">Выбивка песка из труб</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 43, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина трубы</td><td colspan="17">Наружный диаметр трубы Д, мм, до</td></tr>
<tr><td rowspan="2">L, м, до</td><td>12</td><td>16</td><td>20</td><td>25</td><td>32</td><td>42</td><td>50</td><td>63</td><td>83</td><td>102</td><td>121</td><td>140</td><td>159</td><td>194</td><td>245</td><td>325</td><td>426</td></tr>
<tr><td colspan="17">Время Т, чел.-мин.</td></tr>
<tr><td>8</td><td>4,8</td><td>-</td><td>-</td><td>2,45</td><td>2,67</td><td>3,03</td><td>3,47</td><td>3,78</td><td>4,25</td><td>4,87</td><td>5,41</td><td>5,89</td><td>6,33</td><td>6,75</td><td>7,45</td><td>8,38</td><td>9,65</td><td>11,05</td></tr>
<tr><td>9</td><td>6,5</td><td>-</td><td>-</td><td>-</td><td>3,38</td><td>3,82</td><td>4,38</td><td>4,78</td><td>5,36</td><td>6,16</td><td>6,83</td><td>7,43</td><td>7,99</td><td>8,52</td><td>9,41</td><td>10,58</td><td>12,18</td><td>13,95</td></tr>
<tr><td>10</td><td>8,8</td><td>-</td><td>-</td><td>-</td><td>4,27</td><td>4,83</td><td>5,53</td><td>6,03</td><td>6,77</td><td>7,77</td><td>8,62</td><td>9,39</td><td>10,10</td><td>10,76</td><td>11,89</td><td>13,36</td><td>15,39</td><td>17,62</td></tr>
<tr><td>11</td><td>12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>5,42</td><td>6,13</td><td>7,02</td><td>7,66</td><td>8,60</td><td>9,87</td><td>10,94</td><td>11,92</td><td>12,82</td><td>13,66</td><td>15,09</td><td>16,96</td><td>22,37</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td></tr>
</table>


<a id="p102890"></a>Примечания:
1. <a id="p102891"></a>На выжигание одной песчаной пробки в стальных трубах к времени по карте добавлять 0,8 мин.
2. <a id="p102892"></a>При измененных условиях выбивки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="23%"><col width="27%"><col width="26%"><col width="24%"></colgroup>
<tr><td>Факторы,влияющие на изменение</td><td colspan="3">Выбивка песка из труб</td></tr>
<tr><td>нормы времени</td><td>с одним или двумя гибами в одной плоскости</td><td>с гибами в разных плоскостях</td><td>с количеством гибов более двух</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,2</td><td>1,35</td></tr>
</table>


3. <a id="p102895"></a>Работа выполняется одним человеком при L <= 1,5 м и бригадой из двух человек при L > 1,5 м:

                        0,77
                       L
<a id="p102896"></a>             Т = 2,5 х -----         для Д <= 20   поз. 1...11;
                        0,41
                       Д

                         0,77    0,5
<a id="p102897"></a>             Т = 0,16 х L     х Д    для Д > 20    поз. 1...11.


<a id="p102898"></a>

<table>
<colgroup><col width="12%"><col width="12%"><col width="15%"><col width="11%"><col width="11%"><col width="9%"><col width="5%"><col width="4%"><col width="9%"><col width="11%"></colgroup>
<tr><td colspan="7" rowspan="2">Гибка труб на станке с одноручейным сектором</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 44, лист 1</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Взять трубу, установить на направляющий стержень и закрепить.</td></tr>
<tr><td colspan="10">2. Поджать трубу к копиру упора (призмой).</td></tr>
<tr><td colspan="10">3. Включить станок, гнуть трубу.</td></tr>
<tr><td colspan="10">4. Отвести упор, выключить станок.</td></tr>
<tr><td colspan="10">5. Открепить трубу, снять со стержня.</td></tr>
<tr><td colspan="10">6. Отложить трубу.</td></tr>
<tr><td rowspan="5">N позиции</td><td>Способ поджима</td><td>Наружный диаметр</td><td colspan="7">Угол гиба альфа, град., до</td></tr>
<tr><td rowspan="4">трубы к копиру</td><td rowspan="4">трубы Д, мм, до</td><td colspan="2">45</td><td colspan="3">90</td><td colspan="2">180</td></tr>
<tr><td colspan="7">Радиус изгиба R, выраженный в диаметре трубы</td></tr>
<tr><td>&lt;= 2альфа</td><td>&gt; 2альфа</td><td>&lt;= 2альфа</td><td colspan="2">&gt; 2альфа</td><td>&lt;= 2альфа</td><td>&gt; 2альфа</td></tr>
<tr><td colspan="7">Время на один гиб Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">П</td><td>12</td><td>0,45</td><td>0,34</td><td>0,49</td><td colspan="2">0,37</td><td>0,51</td><td>0,40</td></tr>
<tr><td>2</td><td>20</td><td>0,63</td><td>0,48</td><td>0,69</td><td colspan="2">0,52</td><td>0,75</td><td>0,56</td></tr>
<tr><td>3</td><td>32</td><td>0,87</td><td>0,66</td><td>0,95</td><td colspan="2">0,72</td><td>1,03</td><td>0,78</td></tr>
<tr><td>4</td><td>н е</td><td>42</td><td>1,05</td><td>0,79</td><td>1,14</td><td colspan="2">0,86</td><td>1,24</td><td>0,90</td></tr>
<tr><td>5</td><td>в м</td><td>54</td><td>1,27</td><td>0,92</td><td>1,38</td><td colspan="2">1,00</td><td>1,50</td><td>1,08</td></tr>
<tr><td>6</td><td>а т</td><td>68</td><td>1,59</td><td>1,14</td><td>1,73</td><td colspan="2">1,24</td><td>1,87</td><td>1,35</td></tr>
<tr><td>7</td><td>и ч</td><td>89</td><td>2,05</td><td>1,48</td><td>2,23</td><td colspan="2">1,61</td><td>2,42</td><td>1,75</td></tr>
<tr><td>8</td><td>е с</td><td>114</td><td>2,59</td><td>1,87</td><td>2,81</td><td colspan="2">2,03</td><td>3,06</td><td>2,21</td></tr>
<tr><td>9</td><td>к и</td><td>146</td><td>3,28</td><td>2,37</td><td>3,57</td><td colspan="2">2,58</td><td>3,88</td><td>2,80</td></tr>
<tr><td>10</td><td rowspan="4">й</td><td>180</td><td>4,01</td><td>2,89</td><td>4,35</td><td colspan="2">3,14</td><td>4,73</td><td>3,41</td></tr>
<tr><td>11</td><td>203</td><td>4,83</td><td>3,48</td><td>5,25</td><td colspan="2">3,78</td><td>5,70</td><td>4,11</td></tr>
<tr><td>12</td><td>219</td><td>6,30</td><td>4,55</td><td>6,85</td><td colspan="2">4,95</td><td>7,45</td><td>5,37</td></tr>
<tr><td>13</td><td>426</td><td>9,07</td><td>6,54</td><td>9,86</td><td colspan="2">7,11</td><td>10,72</td><td>7,73</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="12%"><col width="15%"><col width="11%"><col width="11%"><col width="9%"><col width="5%"><col width="4%"><col width="9%"><col width="11%"></colgroup>
<tr><td colspan="7" rowspan="2">Гибка труб на станке с одноручейным сектором</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 44, лист 2</td></tr>
<tr><td rowspan="5">N позиции</td><td>Способ поджима</td><td>Наружный диаметр</td><td colspan="7">Угол гиба альфа, град., до</td></tr>
<tr><td rowspan="4">трубы к копиру</td><td rowspan="4">трубы Д, мм, до</td><td colspan="2">45</td><td colspan="3">90</td><td colspan="2">180</td></tr>
<tr><td colspan="7">Радиус изгиба R, выраженный в диаметре трубы</td></tr>
<tr><td>&lt;= 2альфа</td><td>&gt; 2альфа</td><td>&lt;= 2альфа</td><td colspan="2">&gt; 2альфа</td><td>&lt;= 2альфа</td><td>&gt; 2альфа</td></tr>
<tr><td colspan="7">Время на один гиб Т, чел.-мин.</td></tr>
<tr><td>14</td><td rowspan="5">В и</td><td>12</td><td>0,60</td><td>0,44</td><td>0,65</td><td colspan="2">0,48</td><td>0,71</td><td>0,52</td></tr>
<tr><td>15</td><td>20</td><td>0,84</td><td>0,62</td><td>0,92</td><td colspan="2">0,67</td><td>1,00</td><td>0,73</td></tr>
<tr><td>16</td><td>32</td><td>1,16</td><td>0,85</td><td>1,26</td><td colspan="2">0,93</td><td>1,37</td><td>1,01</td></tr>
<tr><td>17</td><td>42</td><td>1,40</td><td>1,03</td><td>1,52</td><td colspan="2">1,12</td><td>1,65</td><td>1,21</td></tr>
<tr><td>18</td><td>54</td><td>1,60</td><td>1,24</td><td>1,74</td><td colspan="2">1,35</td><td>1,89</td><td>1,47</td></tr>
<tr><td>19</td><td>н т</td><td>68</td><td>1,99</td><td>1,55</td><td>2,17</td><td colspan="2">1,68</td><td>2,36</td><td>1,82</td></tr>
<tr><td>20</td><td>о в</td><td>89</td><td>2,58</td><td>1,99</td><td>2,80</td><td colspan="2">2,17</td><td>3,05</td><td>2,36</td></tr>
<tr><td>21</td><td rowspan="6">о й</td><td>114</td><td>3,26</td><td>2,52</td><td>3,55</td><td colspan="2">2,74</td><td>3,86</td><td>2,98</td></tr>
<tr><td>22</td><td>146</td><td>4,13</td><td>3,19</td><td>4,49</td><td colspan="2">3,47</td><td>4,88</td><td>3,77</td></tr>
<tr><td>23</td><td>180</td><td>5,04</td><td>3,90</td><td>5,48</td><td colspan="2">4,23</td><td>5,95</td><td>4,60</td></tr>
<tr><td>24</td><td>219</td><td>6,07</td><td>4,70</td><td>6,60</td><td colspan="2">5,11</td><td>7,17</td><td>5,55</td></tr>
<tr><td>25</td><td>299</td><td>7,93</td><td>6,14</td><td>8,62</td><td colspan="2">6,67</td><td>9,36</td><td>7,25</td></tr>
<tr><td>26</td><td>426</td><td>11,40</td><td>8,82</td><td>12,40</td><td colspan="2">9,59</td><td>13,50</td><td>10,42</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td></tr>
</table>


<a id="p102940"></a>Примечания:
1. <a id="p102941"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="11%"><col width="8%"><col width="9%"><col width="9%"><col width="9%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="9">Гибка труб</td><td colspan="3">Число оборотов гибочного устройства, мин.</td></tr>
<tr><td rowspan="2">нормы времени</td><td rowspan="2">в одной плоскости</td><td rowspan="2">в двух плоскостях</td><td rowspan="2">в трех плоскостях</td><td rowspan="2">с установкой дорна</td><td rowspan="2">без установки дорна</td><td colspan="2">длина труб, м</td><td colspan="2">кол-во гибов</td><td rowspan="2">до 1</td><td rowspan="2">1</td><td rowspan="2">св. 1</td></tr>
<tr><td>до 2</td><td>св. 2</td><td>один гиб</td><td>более одного</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,2</td><td>1,0</td><td>1,0</td><td>1,15</td><td>1,0</td><td>0,7</td><td>1,2</td><td>1,0</td><td>0,85</td></tr>
</table>


2. <a id="p102944"></a>Работа выполняется бригадой их двух человек:


<table>
<colgroup><col width="76%"><col width="24%"></colgroup>
<tr><td rowspan="2">Гибка труб на станке с одноручейным сектором</td><td>Гибка</td></tr>
<tr><td>Карта 44, лист 3</td></tr>
</table>


<a id="p102947"></a>    Пневматический

                        0,68        0,12
<a id="p102948"></a>          Т = 0,0525 х Д     х альфа       R <= 2  поз. 1...4;

                        0,95        0,12
<a id="p102949"></a>          Т = 0,0183 х Д     х альфа       R <= 2  поз. 5...13;

                        0,68        0,12
<a id="p102950"></a>          Т = 0,0397 х Д     х альфа       R > 2   поз. 1...4;

                        0,95        0,12
<a id="p102951"></a>          Т = 0,0132 х Д     х альфа       R > 2   поз. 5...13.

<a id="p102952"></a>    Винтовой

                      0,68        0,12
<a id="p102953"></a>          Т = 0,07 х Д     х альфа         R <= 2  поз. 14...17;

                       0,95        0,12
<a id="p102954"></a>          Т = 0,022 х Д     х альфа        R <= 2  поз. 18...26;

                        0,68        0,12
<a id="p102955"></a>          Т = 0,0514 х Д     х альфа       R > 2   поз. 14...17;

                        0,95        0,12
<a id="p102956"></a>          Т = 0,0178 х Д     х альфа       R > 2   поз. 18...26.


<table>
<colgroup><col width="8%"><col width="9%"><col width="10%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="8" rowspan="2">Гибка труб в роликовом приспособлении в холодном состоянии вручную</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 45, лист 1</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">1. Установить трубу в приспособление, закрепить. (рисунок не</td></tr>
<tr><td colspan="11">2. Гнуть трубу. приводится)</td></tr>
<tr><td colspan="11">3. Проверить угол и радиус гибки шаблоном.</td></tr>
<tr><td colspan="11">4. Подправить.</td></tr>
<tr><td colspan="11">5. Снять трубу, отложить.</td></tr>
<tr><td rowspan="5">N позиции</td><td>Наружный</td><td>Толщина стенки</td><td colspan="8">Угол гибки альфа, град., до</td></tr>
<tr><td>диаметр</td><td>трубы h, мм,</td><td colspan="2">45</td><td colspan="2">90</td><td colspan="2">135</td><td colspan="2">180</td></tr>
<tr><td>трубы Д, мм,</td><td rowspan="3">до</td><td colspan="8">Радиус изгиба R, выраженный в диаметре трубы</td></tr>
<tr><td rowspan="2">до</td><td>&lt;= 2альфа</td><td>&gt; 2альфа</td><td>&lt;= 2альфа</td><td>&gt; 2альфа</td><td>&lt;= 2альфа</td><td>&gt; 2альфа</td><td>&lt;= 2альфа</td><td>&gt; 2альфа</td></tr>
<tr><td colspan="8">Время на один гиб Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="2">12</td><td>1,0</td><td>0,34</td><td>0,31</td><td>0,57</td><td>0,46</td><td>0,78</td><td>0,56</td><td>0,97</td><td>0,67</td></tr>
<tr><td>2</td><td>2,0</td><td>0,41</td><td>0,38</td><td>0,69</td><td>0,55</td><td>0,94</td><td>0,69</td><td>1,17</td><td>0,81</td></tr>
<tr><td>3</td><td rowspan="2">20</td><td>1,0</td><td>0,43</td><td>0,38</td><td>0,73</td><td>0,56</td><td>0,99</td><td>0,70</td><td>1,24</td><td>0,82</td></tr>
<tr><td>4</td><td>2,0</td><td>0,52</td><td>0,46</td><td>0,89</td><td>0,67</td><td>1,21</td><td>0,84</td><td>1,50</td><td>0,98</td></tr>
<tr><td>5</td><td rowspan="3">32</td><td>1,0</td><td>0,54</td><td>0,46</td><td>0,91</td><td>0,67</td><td>1,24</td><td>0,84</td><td>1,55</td><td>0,99</td></tr>
<tr><td>6</td><td>2,0</td><td>0,66</td><td>0,55</td><td>1,11</td><td>0,81</td><td>1,51</td><td>1,01</td><td>1,88</td><td>1,18</td></tr>
<tr><td>7</td><td>3,0</td><td>0,73</td><td>0,61</td><td>1,24</td><td>0,90</td><td>1,69</td><td>1,12</td><td>2,11</td><td>1,31</td></tr>
<tr><td>8</td><td rowspan="3">50</td><td>1,0</td><td>0,67</td><td>0,55</td><td>1,13</td><td>0,80</td><td>1,54</td><td>1,00</td><td>1,82</td><td>1,18</td></tr>
<tr><td>9</td><td>2,0</td><td>0,81</td><td>0,66</td><td>1,38</td><td>0,96</td><td>1,87</td><td>1,20</td><td>2,33</td><td>1,41</td></tr>
<tr><td>10</td><td>3,0</td><td>0,91</td><td>0,73</td><td>1,54</td><td>1,07</td><td>2,10</td><td>1,34</td><td>2,61</td><td>1,56</td></tr>
<tr><td>11</td><td rowspan="3">63</td><td>1,0</td><td>0,75</td><td>0,60</td><td>1,27</td><td>0,88</td><td>1,72</td><td>1,10</td><td>2,14</td><td>1,29</td></tr>
<tr><td>12</td><td>2,0</td><td>0,91</td><td>0,72</td><td>1,54</td><td>1,05</td><td>2,09</td><td>1,32</td><td>2,60</td><td>1,54</td></tr>
<tr><td>13</td><td>3,0</td><td>1,02</td><td>0,80</td><td>1,72</td><td>1,17</td><td>2,34</td><td>1,46</td><td>2,92</td><td>1,71</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p102980"></a>Примечания:
1. <a id="p102981"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="73%"><col width="27%"></colgroup>
<tr><td rowspan="2">Гибка труб в роликовом приспособлении в холодном состоянии вручную</td><td>Гибка</td></tr>
<tr><td>Карта 45, лист 2</td></tr>
</table>



<table>
<colgroup><col width="10%"><col width="9%"><col width="9%"><col width="9%"><col width="7%"><col width="8%"><col width="9%"><col width="7%"><col width="8%"><col width="5%"><col width="5%"><col width="8%"><col width="8%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td><td colspan="5">Гибка труб</td><td colspan="2">Длина трубы, м</td><td colspan="2">Способ гибки</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>в одной плоскости</td><td>в двух плоскостях</td><td>в трехчетырех плоскостях</td><td>без песка</td><td>наполненных песком</td><td>до 2</td><td>св. 2</td><td>в холодном состоянии</td><td>в горячем состоянии</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,15</td><td>1,0</td><td>0,85</td></tr>
</table>


2. <a id="p102986"></a>Работа выполняется одним человеком:

                     0,48    0,28        0,76
<a id="p102987"></a>      Т = 0,00567 х Д     х h     х альфа       R <= 2 поз. 1...13;

                    0,39    0,26        0,55
<a id="p102988"></a>      Т = 0,0147 х Д     х h     х альфа        R > 2  поз. 1...13.


<table>
<colgroup><col width="8%"><col width="9%"><col width="10%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="5%"><col width="4%"><col width="9%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="8" rowspan="2">Гибка труб на плите по упорам в холодном состоянии вручную</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 46, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Взять трубу, установить на плиту. (рисунок не</td></tr>
<tr><td colspan="12">2. Гнуть трубу по упору. приводится)</td></tr>
<tr><td colspan="12">3. Проверить угол и радиус гибки шаблоном.</td></tr>
<tr><td colspan="12">4. Подправить.</td></tr>
<tr><td colspan="12">5. Снять трубу, отложить.</td></tr>
<tr><td rowspan="5">N позиции</td><td>Наружный</td><td>Толщина стенки</td><td colspan="9">Угол гибки альфа, град., до</td></tr>
<tr><td>диаметр</td><td rowspan="4">h, мм, до</td><td colspan="2">45</td><td colspan="2">90</td><td colspan="3">135</td><td colspan="2">180</td></tr>
<tr><td rowspan="3">Д, мм, до</td><td colspan="9">Радиус изгиба R, выраженный в диаметре трубы</td></tr>
<tr><td>&lt;= 2альфа</td><td>&gt; 2альфа</td><td>&lt;= 2альфа</td><td>&gt; 2альфа</td><td colspan="2">&lt;= 2альфа</td><td>&gt; 2альфа</td><td>&lt;= 2альфа</td><td>&gt; 2альфа</td></tr>
<tr><td colspan="9">Время на один гиб Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="2">12</td><td>1,0</td><td>0,80</td><td>0,57</td><td>1,17</td><td>0,81</td><td colspan="2">1,43</td><td>0,99</td><td>1,65</td><td>1,14</td></tr>
<tr><td>2</td><td>2,0</td><td>1,02</td><td>0,70</td><td>1,44</td><td>0,99</td><td colspan="2">1,76</td><td>1,22</td><td>2,04</td><td>1,41</td></tr>
<tr><td>3</td><td rowspan="2">20</td><td>1,0</td><td>1,06</td><td>0,73</td><td>1,49</td><td>1,03</td><td colspan="2">1,83</td><td>1,26</td><td>2,12</td><td>1,46</td></tr>
<tr><td>4</td><td>2,0</td><td>1,30</td><td>0,90</td><td>1,84</td><td>1,27</td><td colspan="2">2,26</td><td>1,56</td><td>2,61</td><td>1,80</td></tr>
<tr><td>5</td><td rowspan="3">32</td><td>1,0</td><td>1,32</td><td>0,91</td><td>1,87</td><td>1,29</td><td colspan="2">2,29</td><td>1,58</td><td>2,65</td><td>1,83</td></tr>
<tr><td>6</td><td>2,0</td><td>1,63</td><td>1,13</td><td>2,31</td><td>1,59</td><td colspan="2">2,83</td><td>1,95</td><td>3,26</td><td>2,25</td></tr>
<tr><td>7</td><td>3,0</td><td>1,84</td><td>1,27</td><td>2,61</td><td>1,80</td><td colspan="2">3,19</td><td>2,20</td><td>3,69</td><td>2,55</td></tr>
<tr><td>8</td><td rowspan="3">50</td><td>1,0</td><td>1,64</td><td>1,13</td><td>2,32</td><td>1,61</td><td colspan="2">2,84</td><td>1,96</td><td>3,28</td><td>2,27</td></tr>
<tr><td>9</td><td>2,0</td><td>2,02</td><td>1,29</td><td>2,86</td><td>1,97</td><td colspan="2">3,50</td><td>2,42</td><td>4,05</td><td>2,79</td></tr>
<tr><td>10</td><td>3,0</td><td>2,28</td><td>1,58</td><td>3,23</td><td>2,23</td><td colspan="2">3,96</td><td>2,73</td><td>4,57</td><td>3,15</td></tr>
<tr><td>11</td><td rowspan="3">68</td><td>1,0</td><td>1,90</td><td>1,31</td><td>2,69</td><td>1,86</td><td colspan="2">3,30</td><td>2,28</td><td>3,81</td><td>2,63</td></tr>
<tr><td>12</td><td>2,0</td><td>2,34</td><td>1,62</td><td>3,32</td><td>2,29</td><td colspan="2">4,06</td><td>2,81</td><td>4,69</td><td>3,24</td></tr>
<tr><td>13</td><td>3,0</td><td>2,65</td><td>1,83</td><td>3,74</td><td>2,58</td><td colspan="2">4,59</td><td>3,17</td><td>5,30</td><td>3,66</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="9%"><col width="10%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="5%"><col width="4%"><col width="9%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="8" rowspan="2">Гибка труб на плите по упорам в холодном состоянии вручную</td><td colspan="4">Гибка</td></tr>
<tr><td colspan="4">Карта 46, лист 2</td></tr>
<tr><td rowspan="5">N позиции</td><td>Наружный</td><td>Толщина стенки</td><td colspan="9">Угол гибки альфа, град., до</td></tr>
<tr><td>диаметр</td><td rowspan="4">h, мм, до</td><td colspan="2">45</td><td colspan="2">90</td><td colspan="3">135</td><td colspan="2">180</td></tr>
<tr><td rowspan="3">Д, мм, до</td><td colspan="9">Радиус изгиба R, выраженный в диаметре трубы</td></tr>
<tr><td>&lt;= 2альфа</td><td>&gt; 2альфа</td><td>&lt;= 2альфа</td><td>&gt; 2альфа</td><td colspan="2">&lt;= 2альфа</td><td>&gt; 2альфа</td><td>&lt;= 2альфа</td><td>&gt; 2альфа</td></tr>
<tr><td colspan="9">Время на один гиб Т, чел.-мин.</td></tr>
<tr><td>14</td><td rowspan="3">83</td><td>1,0</td><td>2,09</td><td>1,44</td><td>2,96</td><td>2,05</td><td colspan="2">3,63</td><td>2,50</td><td>4,19</td><td>2,89</td></tr>
<tr><td>15</td><td>2,0</td><td>2,58</td><td>1,78</td><td>3,65</td><td>2,52</td><td colspan="2">4,47</td><td>3,09</td><td>5,16</td><td>3,56</td></tr>
<tr><td>16</td><td>3,0</td><td>2,91</td><td>2,01</td><td>4,12</td><td>2,84</td><td colspan="2">5,05</td><td>3,48</td><td>5,83</td><td>4,02</td></tr>
<tr><td>17</td><td rowspan="3">110</td><td>1,0</td><td>2,40</td><td>1,65</td><td>3,39</td><td>2,34</td><td colspan="2">4,16</td><td>2,87</td><td>4,80</td><td>3,31</td></tr>
<tr><td>18</td><td>2,0</td><td>2,95</td><td>2,04</td><td>4,18</td><td>2,88</td><td colspan="2">5,12</td><td>3,53</td><td>5,91</td><td>4,08</td></tr>
<tr><td>19</td><td>3,0</td><td>3,34</td><td>2,30</td><td>4,72</td><td>3,26</td><td colspan="2">5,78</td><td>3,99</td><td>6,67</td><td>4,61</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p103022"></a>Примечания:
1. <a id="p103023"></a>При измененных условиях гибки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="12%"><col width="10%"><col width="10%"><col width="10%"><col width="8%"><col width="9%"><col width="10%"><col width="8%"><col width="9%"><col width="6%"><col width="6%"></colgroup>
<tr><td rowspan="3">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td><td colspan="5">Гибка труб</td><td colspan="2"></td></tr>
<tr><td rowspan="2">легированная сталь</td><td rowspan="2">углеродистая сталь</td><td rowspan="2">цветные сплавы</td><td rowspan="2">в одной плоскости</td><td rowspan="2">в двух плоскостях</td><td rowspan="2">в трехчетырех плоскостях</td><td rowspan="2">без песка</td><td rowspan="2">наполненные песком</td><td colspan="2">Длина трубы, м</td></tr>
<tr><td>до 2</td><td>св. 2</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,15</td></tr>
</table>


2. <a id="p103026"></a>Работа выполняется одним человеком:

                   0,48    0,3        0,5
<a id="p103027"></a>     Т = 0,0375 х Д     х h    х альфа      при R <= 2   поз. 1...19;

                   0,48    0,3        0,5
<a id="p103028"></a>     Т = 0,0259 х Д     х h    х альфа      при R > 2    поз. 1...19.


<table>
<colgroup><col width="12%"><col width="19%"><col width="8%"><col width="9%"><col width="8%"><col width="9%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Штамповка сферических днищ в горячем состоянии на гидравлическом прессе</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 47, лист 1</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Подать заготовку, загрузить в печь. (рисунок не</td></tr>
<tr><td colspan="10">2. Выгрузить заготовку из печи, подать под пресс. приводится)</td></tr>
<tr><td colspan="10">3. Штамповать днище.</td></tr>
<tr><td colspan="10">4. Снять днище, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр днища Д, мм, до</td><td colspan="8">Толщина металла h, мм, до</td></tr>
<tr><td>4</td><td>7</td><td>12</td><td>20</td><td>34</td><td>56</td><td>95</td><td>160</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>300</td><td>2,24</td><td>2,69</td><td>3,22</td><td>3,81</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>350</td><td>2,69</td><td>3,24</td><td>3,87</td><td>4,58</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>400</td><td>3,16</td><td>3,80</td><td>4,54</td><td>5,40</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>450</td><td>3,64</td><td>4,38</td><td>5,23</td><td>6,20</td><td>7,38</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>500</td><td>4,13</td><td>4,97</td><td>5,94</td><td>7,03</td><td>8,37</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>600</td><td>5,14</td><td>6,19</td><td>7,39</td><td>8,75</td><td>10,40</td><td>12,3</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>700</td><td>6,19</td><td>7,44</td><td>8,89</td><td>10,60</td><td>12,50</td><td>14,8</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>800</td><td>7,26</td><td>8,74</td><td>10,40</td><td>12,30</td><td>14,70</td><td>17,4</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>950</td><td>8,93</td><td>10,70</td><td>12,80</td><td>15,20</td><td>18,10</td><td>21,3</td><td>25,4</td><td>-</td></tr>
<tr><td>10</td><td>1100</td><td>10,70</td><td>12,80</td><td>15,30</td><td>18,10</td><td>21,50</td><td>25,4</td><td>30,3</td><td>-</td></tr>
<tr><td>11</td><td>1300</td><td>13,00</td><td>15,60</td><td>18,70</td><td>22,10</td><td>26,40</td><td>31,1</td><td>37,0</td><td>44,0</td></tr>
<tr><td>12</td><td>1500</td><td>15,50</td><td>18,60</td><td>22,20</td><td>26,30</td><td>31,30</td><td>37,0</td><td>44,0</td><td>52,2</td></tr>
<tr><td>13</td><td>1700</td><td>18,00</td><td>21,60</td><td>25,80</td><td>30,50</td><td>37,00</td><td>43,0</td><td>51,1</td><td>60,6</td></tr>
<tr><td>14</td><td>1900</td><td>-</td><td>24,70</td><td>29,50</td><td>34,90</td><td>41,60</td><td>49,0</td><td>58,4</td><td>69,3</td></tr>
<tr><td>15</td><td>2200</td><td>-</td><td>29,40</td><td>35,20</td><td>41,60</td><td>49,60</td><td>58,4</td><td>69,5</td><td>82,6</td></tr>
<tr><td>16</td><td>2500</td><td>-</td><td>-</td><td>41,00</td><td>48,50</td><td>57,80</td><td>68,1</td><td>81,1</td><td>96,3</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="19%"><col width="8%"><col width="9%"><col width="8%"><col width="9%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Штамповка сферических днищ в горячем состоянии на гидравлическом прессе</td><td colspan="3">Гибка</td></tr>
<tr><td colspan="3">Карта 47, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр днища Д, мм, до</td><td colspan="8">Толщина металла h, мм, до</td></tr>
<tr><td>4</td><td>7</td><td>12</td><td>20</td><td>34</td><td>56</td><td>95</td><td>160</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>17</td><td>2900</td><td>-</td><td>-</td><td>48,9</td><td>57,9</td><td>69,1</td><td>81,4</td><td>96,9</td><td>115,1</td></tr>
<tr><td>18</td><td>3400</td><td>-</td><td>-</td><td>-</td><td>70,1</td><td>83,6</td><td>98,5</td><td>117,3</td><td>139,4</td></tr>
<tr><td>19</td><td>4000</td><td>-</td><td>-</td><td>-</td><td>85,3</td><td>101,6</td><td>119,8</td><td>142,6</td><td>169,4</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p103061"></a>Примечания:
1. <a id="p103062"></a>При измененных условиях штамповки приведенное в нормативной карте время применяется с коэффициентами:


<a id="p103065"></a><a id="p103066"></a>

<table>
<colgroup><col width="49%"><col width="26%"><col width="26%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="2">Материал</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td></tr>
<tr><td>2. Работа выполняется бригадой из двух человек:</td><td></td><td></td></tr>
<tr><td>1,2</td><td>0,33</td><td></td></tr>
<tr><td>Т = 0,00151 х Д</td><td>х h поз. 1...19.</td><td></td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="16%"><col width="16%"><col width="15%"><col width="13%"><col width="7%"><col width="8%"><col width="13%"></colgroup>
<tr><td colspan="6" rowspan="2">Отбортовка цилиндрических обечаек на станке</td><td colspan="2">Гибка</td></tr>
<tr><td colspan="2">Карта 48</td></tr>
<tr><td colspan="8">Содержание работы</td></tr>
<tr><td colspan="8">1. Подать обечайку к станку. (рисунок не</td></tr>
<tr><td colspan="8">2. Установить обечайку на станок. приводится)</td></tr>
<tr><td colspan="8">3. Отбортовать кройку обечайки.</td></tr>
<tr><td colspan="8">4. Снять отбортованную обечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки Д,</td><td>Длина обечайки L,</td><td colspan="5">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">мм, до</td><td rowspan="2">мм, до</td><td>2</td><td>4</td><td colspan="2">8</td><td>16</td></tr>
<tr><td colspan="5">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">700</td><td>400</td><td>8,9</td><td>10,1</td><td colspan="2">11,4</td><td>12,9</td></tr>
<tr><td>2</td><td>900</td><td>10,5</td><td>11,9</td><td colspan="2">13,5</td><td>19,3</td></tr>
<tr><td>3</td><td>2200</td><td>12,7</td><td>14,4</td><td colspan="2">16,3</td><td>18,5</td></tr>
<tr><td>4</td><td rowspan="3">1200</td><td>400</td><td>10,8</td><td>12,2</td><td colspan="2">13,8</td><td>15,7</td></tr>
<tr><td>5</td><td>900</td><td>12,8</td><td>14,5</td><td colspan="2">16,4</td><td>18,6</td></tr>
<tr><td>6</td><td>2200</td><td>15,4</td><td>17,5</td><td colspan="2">19,8</td><td>22,4</td></tr>
<tr><td>7</td><td rowspan="2">2000</td><td>900</td><td>15,4</td><td>17,4</td><td colspan="2">19,8</td><td>22,4</td></tr>
<tr><td>8</td><td>2200</td><td>18,5</td><td>21,0</td><td colspan="2">23,8</td><td>26,9</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td>г</td></tr>
</table>


<a id="p103084"></a>Примечания:
1. <a id="p103085"></a>При измененных условиях отбортовки приведенное в нормативной карте время применяется с коэффициентами:


<a id="p103088"></a><a id="p103089"></a>

<table>
<colgroup><col width="47%"><col width="25%"><col width="28%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="2">Материал</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td></tr>
<tr><td>2. Работа выполняется одним человеком:</td><td></td><td></td></tr>
<tr><td>0,36</td><td>0,21 0,18</td><td></td></tr>
<tr><td>Т = 0,211 х Д х L</td><td>х h поз. 1...8.</td><td></td></tr>
</table>



#### <a id="p103090"></a>Раздел 4. УКРУПНЕННЫЕ НОРМАТИВЫ ШТУЧНОГО ВРЕМЕНИ НА СЛЕСАРНО- И СЛЕСАРНО-СБОРОЧНЫЕ РАБОТЫ



<table>
<colgroup><col width="8%"><col width="8%"><col width="13%"><col width="9%"><col width="13%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Установка деталей, узлов на плоскость или на шпильки вручную</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 49, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">Установка на плоскость</td></tr>
<tr><td colspan="12">1. Взять деталь (узел), установить на плоскость с выверкой по отверстиям, рискам кромкам.</td></tr>
<tr><td colspan="12">Установка на шпильки</td></tr>
<tr><td colspan="12">1. Взять деталь (узел).</td></tr>
<tr><td colspan="12">2. Установить на шпильки с подправкой шпилек кувалдой.</td></tr>
<tr><td rowspan="4">N позиции</td><td rowspan="4">Положение установки</td><td rowspan="4">Наибольший размер детали или узла в плоскости установки L, мм, до</td><td rowspan="4">Масса м, кг, до</td><td rowspan="3">Установка на плоскость с выверкой по отверстиям, рискам или кромкам</td><td colspan="7">Установка на шпильки</td></tr>
<tr><td colspan="7">Количество шпилек n, шт., до</td></tr>
<tr><td>2</td><td>4</td><td>6</td><td>8</td><td>12</td><td>16</td><td>24</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="2">Г о</td><td rowspan="6">1000</td><td>1</td><td>0,48</td><td>0,40</td><td>0,55</td><td>0,74</td><td>0,92</td><td>1,25</td><td>1,55</td><td>2,15</td></tr>
<tr><td>2</td><td>3</td><td>0,56</td><td>0,47</td><td>0,64</td><td>0,86</td><td>1,05</td><td>1,45</td><td>1,85</td><td>2,50</td></tr>
<tr><td>3</td><td>р и</td><td>5</td><td>0,60</td><td>0,50</td><td>0,68</td><td>0,93</td><td>1,15</td><td>1,60</td><td>2,00</td><td>2,70</td></tr>
<tr><td>4</td><td>з о</td><td>10</td><td>0,66</td><td>0,55</td><td>0,75</td><td>1,00</td><td>1,30</td><td>1,75</td><td>2,15</td><td>2,95</td></tr>
<tr><td>5</td><td>н т</td><td>15</td><td>0,70</td><td>0,58</td><td>0,80</td><td>1,10</td><td>1,35</td><td>1,85</td><td>2,30</td><td>3,15</td></tr>
<tr><td>6</td><td>а л</td><td>20</td><td>0,73</td><td>0,61</td><td>0,83</td><td>1,13</td><td>1,41</td><td>1,92</td><td>2,40</td><td>3,28</td></tr>
<tr><td>7</td><td>ь н</td><td rowspan="4">1500</td><td>5</td><td>0,66</td><td>0,57</td><td>0,78</td><td>1,05</td><td>1,30</td><td>1,80</td><td>2,25</td><td>3,05</td></tr>
<tr><td>8</td><td rowspan="3">о е</td><td>10</td><td>0,73</td><td>0,63</td><td>0,86</td><td>1,15</td><td>1,45</td><td>2,00</td><td>2,50</td><td>3,40</td></tr>
<tr><td>9</td><td>15</td><td>0,77</td><td>0,67</td><td>0,91</td><td>1,25</td><td>1,55</td><td>2,10</td><td>2,60</td><td>3,60</td></tr>
<tr><td>10</td><td>20</td><td>0,81</td><td>0,70</td><td>0,95</td><td>1,29</td><td>1,61</td><td>2,20</td><td>2,74</td><td>3,75</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="8%"><col width="13%"><col width="9%"><col width="13%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Установка деталей, узлов на плоскость или на шпильки вручную</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 49, лист 2</td></tr>
<tr><td rowspan="4">N позиции</td><td rowspan="4">Положение установки</td><td rowspan="4">Наибольший размер детали или узла в плоскости установки L, мм, до</td><td rowspan="4">Масса м, кг, до</td><td rowspan="3">Установка на плоскость с выверкой по отверстиям, рискам или кромкам</td><td colspan="7">Установка на шпильки</td></tr>
<tr><td colspan="7">Количество шпилек n, шт., до</td></tr>
<tr><td>2</td><td>4</td><td>6</td><td>8</td><td>12</td><td>16</td><td>24</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>11</td><td rowspan="4">Б о</td><td rowspan="6">1000</td><td>1</td><td>0,55</td><td>0,48</td><td>0,66</td><td>0,90</td><td>1,10</td><td>1,50</td><td>1,90</td><td>2,60</td></tr>
<tr><td>12</td><td>3</td><td>0,65</td><td>0,56</td><td>0,77</td><td>1,05</td><td>1,30</td><td>1,75</td><td>2,20</td><td>3,05</td></tr>
<tr><td>13</td><td>5</td><td>0,70</td><td>0,60</td><td>0,83</td><td>1,10</td><td>1,40</td><td>1,90</td><td>2,40</td><td>3,25</td></tr>
<tr><td>14</td><td>10</td><td>0,77</td><td>0,67</td><td>0,91</td><td>1,25</td><td>1,55</td><td>2,10</td><td>2,60</td><td>3,60</td></tr>
<tr><td>15</td><td>к о</td><td>15</td><td>0,81</td><td>0,70</td><td>0,96</td><td>1,30</td><td>1,65</td><td>2,25</td><td>2,80</td><td>3,80</td></tr>
<tr><td>16</td><td>в о</td><td>20</td><td>0,85</td><td>0,74</td><td>1,00</td><td>1,36</td><td>1,70</td><td>2,33</td><td>2,90</td><td>3,97</td></tr>
<tr><td>17</td><td rowspan="4">е</td><td rowspan="4">1500</td><td>5</td><td>0,77</td><td>0,69</td><td>0,94</td><td>1,25</td><td>1,60</td><td>2,20</td><td>2,70</td><td>3,70</td></tr>
<tr><td>18</td><td>10</td><td>0,84</td><td>0,76</td><td>1,05</td><td>1,40</td><td>1,75</td><td>2,40</td><td>3,00</td><td>4,10</td></tr>
<tr><td>19</td><td>15</td><td>0,89</td><td>0,81</td><td>1,10</td><td>1,50</td><td>1,85</td><td>2,55</td><td>3,20</td><td>4,35</td></tr>
<tr><td>20</td><td>20</td><td>0,93</td><td>0,84</td><td>1,15</td><td>1,56</td><td>1,95</td><td>2,66</td><td>3,32</td><td>4,53</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p103126"></a>Примечания:
1. <a id="p103127"></a>При снятии деталей, узлов время по карте применять с коэффициентом 0,7.
2. <a id="p103128"></a>Работа выполняется одним человеком:

                    0,23    0,14
<a id="p103129"></a>      Т = 0,0985 х L     х М               индекс а    поз. 1...10;

                   0,23    0,14
<a id="p103130"></a>      Т = 0,114 х L     х М                индекс а     поз. 11...20;

                  0,33    0,14    0,45
<a id="p103131"></a>      Т = 0,03 х L     х М     х n         при n <= 4   поз. 1...10;

                    0,33    0,14    0,77
<a id="p103132"></a>      Т = 0,0191 х L     х М     х n       при n > 4    поз. 1...10;

                    0,33    0,14    0,45
<a id="p103133"></a>      Т = 0,0362 х L     х М     х n       при n <= 4   поз. 11...20;

                    0,33    0,14    0,77
<a id="p103134"></a>      Т = 0,0231 х L     х М     х n       при n > 4    поз. 11...20.


<table>
<colgroup><col width="8%"><col width="8%"><col width="13%"><col width="8%"><col width="13%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Установка деталей, узлов на плоскость или на шпильки краном</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 50, лист 1</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">Установка на плоскость (рисунок не</td></tr>
<tr><td colspan="13">1. Застропить деталь (узел). приводится)</td></tr>
<tr><td colspan="13">2. Установить на плоскость с выверкой по отверстиям, рискам, кромкам.</td></tr>
<tr><td colspan="13">3. Отстропить деталь (узел).</td></tr>
<tr><td colspan="13">Установка на шпильки</td></tr>
<tr><td colspan="13">1. Застропить деталь (узел).</td></tr>
<tr><td colspan="13">2. Установить на шпильки с подправкой шпилек кувалдой.</td></tr>
<tr><td colspan="13">3. Отстропить деталь (узел).</td></tr>
<tr><td rowspan="4">N позиции</td><td>Положение</td><td>Наибольший</td><td>Масса м,</td><td rowspan="2">Установка на плоскость с выверкой</td><td colspan="8">Установка на шпильки</td></tr>
<tr><td rowspan="3">установки</td><td>размер детали</td><td rowspan="3">кг, до</td><td colspan="8">Количество шпилек n, шт., до</td></tr>
<tr><td rowspan="2">или узла в плоскости установки L, мм, до</td><td>по отверстиям, рискам или кромкам</td><td>2</td><td>4</td><td>6</td><td colspan="2">8</td><td>12</td><td>16</td><td>24</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>Г</td><td rowspan="9">2000</td><td>100</td><td>1,67</td><td>1,94</td><td>2,57</td><td>3,04</td><td colspan="2">3,42</td><td>4,04</td><td>4,54</td><td>5,36</td></tr>
<tr><td>2</td><td>о р</td><td>250</td><td>2,32</td><td>2,26</td><td>3,01</td><td>3,55</td><td colspan="2">3,99</td><td>4,72</td><td>5,31</td><td>6,27</td></tr>
<tr><td>3</td><td>и з</td><td>500</td><td>2,98</td><td>-</td><td>3,38</td><td>3,99</td><td colspan="2">4,49</td><td>5,31</td><td>5,97</td><td>7,05</td></tr>
<tr><td>4</td><td>о н</td><td>1000</td><td>3,82</td><td>-</td><td>-</td><td>-</td><td colspan="2">5,06</td><td>5,97</td><td>6,72</td><td>7,93</td></tr>
<tr><td>5</td><td>т а</td><td>2000</td><td>4,90</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>6,72</td><td>7,56</td><td>8,92</td></tr>
<tr><td>6</td><td>л ь</td><td>3000</td><td>5,67</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>8,10</td><td>9,56</td></tr>
<tr><td>7</td><td>н о</td><td>5000</td><td>6,82</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>8,83</td><td>10,43</td></tr>
<tr><td>8</td><td rowspan="2">е</td><td>10000</td><td>8,75</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>9,93</td><td>11,73</td></tr>
<tr><td>9</td><td>15000</td><td>10,12</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>10,64</td><td>12,57</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="8%"><col width="13%"><col width="8%"><col width="13%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Установка деталей, узлов на плоскость или на шпильки краном</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 50, лист 2</td></tr>
<tr><td rowspan="4">N позиции</td><td>Положение</td><td>Наибольший</td><td>Масса м,</td><td rowspan="2">Установка на плоскость с выверкой</td><td colspan="8">Установка на шпильки</td></tr>
<tr><td rowspan="3">установки</td><td>размер детали</td><td rowspan="3">кг, до</td><td colspan="8">Количество шпилек n, шт., до</td></tr>
<tr><td rowspan="2">или узла в плоскости установки L, мм, до</td><td>по отверстиям, рискам или кромкам</td><td>2</td><td>4</td><td>6</td><td colspan="2">8</td><td>12</td><td>16</td><td>24</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>10</td><td rowspan="4">Г</td><td rowspan="3">2000</td><td>20000</td><td>11,23</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>11,18</td><td>13,20</td></tr>
<tr><td>11</td><td>25000</td><td>12,17</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>11,61</td><td>13,71</td></tr>
<tr><td>12</td><td>30000</td><td>12,99</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>11,97</td><td>14,14</td></tr>
<tr><td>13</td><td rowspan="12">2500</td><td>100</td><td>1,76</td><td>2,10</td><td>2,79</td><td>3,29</td><td colspan="2">3,71</td><td>4,38</td><td>4,93</td><td>5,82</td></tr>
<tr><td>14</td><td>о р</td><td>250</td><td>2,45</td><td>2,45</td><td>3,26</td><td>3,85</td><td colspan="2">4,33</td><td>5,12</td><td>5,76</td><td>6,80</td></tr>
<tr><td>15</td><td>и з</td><td>500</td><td>3,15</td><td>-</td><td>3,67</td><td>4,33</td><td colspan="2">4,87</td><td>5,76</td><td>6,48</td><td>7,65</td></tr>
<tr><td>16</td><td>о н</td><td>1000</td><td>4,04</td><td>-</td><td>-</td><td>-</td><td colspan="2">5,48</td><td>6,47</td><td>7,29</td><td>8,60</td></tr>
<tr><td>17</td><td>т а</td><td>2000</td><td>5,18</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>7,28</td><td>8,20</td><td>9,68</td></tr>
<tr><td>18</td><td>л ь</td><td>3000</td><td>6,00</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>8,78</td><td>10,37</td></tr>
<tr><td>19</td><td>н о</td><td>5000</td><td>7,20</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>9,58</td><td>11,31</td></tr>
<tr><td>20</td><td rowspan="5">е</td><td>10000</td><td>9,25</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>10,78</td><td>12,73</td></tr>
<tr><td>21</td><td>15000</td><td>10,70</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>11,55</td><td>13,63</td></tr>
<tr><td>22</td><td>20000</td><td>11,87</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>12,12</td><td>21,68</td></tr>
<tr><td>23</td><td>25000</td><td>12,86</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>12,59</td><td>14,87</td></tr>
<tr><td>24</td><td>30000</td><td>13,74</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>12,99</td><td>15,34</td></tr>
<tr><td>25</td><td>Б</td><td rowspan="5">2000</td><td>100</td><td>1,75</td><td>2,49</td><td>3,31</td><td>3,91</td><td colspan="2">4,40</td><td>5,19</td><td>5,85</td><td>6,90</td></tr>
<tr><td>26</td><td>о к</td><td>250</td><td>2,44</td><td>2,91</td><td>3,87</td><td>4,57</td><td colspan="2">5,14</td><td>6,07</td><td>6,83</td><td>8,07</td></tr>
<tr><td>27</td><td>о в</td><td>500</td><td>3,13</td><td>-</td><td>4,35</td><td>5,14</td><td colspan="2">5,79</td><td>6,83</td><td>7,69</td><td>9,08</td></tr>
<tr><td>28</td><td rowspan="2">о е</td><td>1000</td><td>4,02</td><td>-</td><td>-</td><td>-</td><td colspan="2">6,51</td><td>7,69</td><td>8,65</td><td>10,21</td></tr>
<tr><td>29</td><td>2000</td><td>5,16</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>8,65</td><td>9,73</td><td>11,49</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="8%"><col width="13%"><col width="8%"><col width="13%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Установка деталей, узлов на плоскость или на шпильки краном</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 50, лист 3</td></tr>
<tr><td rowspan="4">N позиции</td><td>Положение</td><td>Наибольший</td><td>Масса м,</td><td rowspan="2">Установка на плоскость с выверкой</td><td colspan="8">Установка на шпильки</td></tr>
<tr><td rowspan="3">установки</td><td>размер детали</td><td rowspan="3">кг, до</td><td colspan="8">Количество шпилек n, шт., до</td></tr>
<tr><td rowspan="2">или узла в плоскости установки L, мм, до</td><td>по отверстиям, рискам или кромкам</td><td>2</td><td>4</td><td>6</td><td colspan="2">8</td><td>12</td><td>16</td><td>24</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>30</td><td rowspan="8">Б</td><td rowspan="7">2000</td><td>3000</td><td>5,97</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>10,42</td><td>12,31</td></tr>
<tr><td>31</td><td>5000</td><td>7,18</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>11,37</td><td>13,43</td></tr>
<tr><td>32</td><td>10000</td><td>9,21</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>12,79</td><td>15,10</td></tr>
<tr><td>33</td><td>15000</td><td>10,66</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>13,70</td><td>16,18</td></tr>
<tr><td>34</td><td>20000</td><td>11,82</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>14,39</td><td>16,99</td></tr>
<tr><td>35</td><td>25000</td><td>12,81</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>14,95</td><td>17,65</td></tr>
<tr><td>36</td><td>30000</td><td>13,68</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>15,42</td><td>18,21</td></tr>
<tr><td>37</td><td rowspan="12">2500</td><td>100</td><td>1,86</td><td>2,70</td><td>3,59</td><td>4,24</td><td colspan="2">4,77</td><td>5,64</td><td>6,34</td><td>7,49</td></tr>
<tr><td>38</td><td>о к</td><td>250</td><td>2,58</td><td>3,16</td><td>4,20</td><td>4,96</td><td colspan="2">5,58</td><td>6,59</td><td>7,41</td><td>8,75</td></tr>
<tr><td>39</td><td>о в</td><td>500</td><td>3,31</td><td>-</td><td>4,72</td><td>5,58</td><td colspan="2">6,27</td><td>7,41</td><td>8,34</td><td>9,85</td></tr>
<tr><td>40</td><td rowspan="9">о е</td><td>1000</td><td>4,25</td><td>-</td><td>-</td><td>-</td><td colspan="2">7,06</td><td>8,34</td><td>9,38</td><td>11,08</td></tr>
<tr><td>41</td><td>2000</td><td>5,45</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>9,38</td><td>10,55</td><td>12,46</td></tr>
<tr><td>42</td><td>3000</td><td>6,31</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>11,31</td><td>13,35</td></tr>
<tr><td>43</td><td>5000</td><td>7,59</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>12,33</td><td>13,54</td></tr>
<tr><td>44</td><td>10000</td><td>9,74</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>13,87</td><td>16,38</td></tr>
<tr><td>45</td><td>15000</td><td>11,27</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>14,86</td><td>17,55</td></tr>
<tr><td>46</td><td>20000</td><td>12,50</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>15,61</td><td>18,43</td></tr>
<tr><td>47</td><td>25000</td><td>13,54</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>16,21</td><td>19,14</td></tr>
<tr><td>48</td><td>30000</td><td>14,46</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>16,72</td><td>19,75</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p103205"></a>Примечания:
1. <a id="p103206"></a>При снятии деталей, узлов время по карте применять с коэффициентом 0,7.


<a id="p103209"></a><a id="p103210"></a><a id="p103211"></a><a id="p103212"></a><a id="p103213"></a>

<table>
<colgroup><col width="75%"><col width="25%"></colgroup>
<tr><td rowspan="2">Установка деталей, узлов на плоскость или на шпильки краном</td><td>Слесарные работы</td></tr>
<tr><td>Карта 50, лист 4</td></tr>
<tr><td>2. Работа выполняется бригадой из двух человек:</td><td></td></tr>
<tr><td>0,25 0,36 Т = 0,0475 х L х M индекс а</td><td>поз. 1...24;</td></tr>
<tr><td>0,37 0,17 0,41 Т = 0,04 х L х M х n индекс б - з</td><td>поз. 1...24;</td></tr>
<tr><td>0,25 0,36 Т = 0,05 х L х M индекс а</td><td>поз. 25...48;</td></tr>
<tr><td>0,37 0,17 0,41 Т = 0,0515 х L х M х n индекс б - з</td><td>поз. 25...48.</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="10%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="2%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="11" rowspan="2">Разметка мест установки деталей, узлов</td><td colspan="6">Слесарные работы</td></tr>
<tr><td colspan="6">Карта 51, лист 1</td></tr>
<tr><td colspan="17">I. Разметка и нанесение четырех осевых линий на корпусе аппарата</td></tr>
<tr><td colspan="17">Содержание работы</td></tr>
<tr><td colspan="17">1. Разметить торец корпуса на четыре равные части, выдержав размер от базового шва, наметить по линейке или отбить шнуром линию главной оси.</td></tr>
<tr><td colspan="17">2. Кернить линию главной оси.</td></tr>
<tr><td colspan="17">3. Наметить по линейке или отбить шнуром остальные три оси.</td></tr>
<tr><td colspan="17">4. Кернить линии осей.</td></tr>
<tr><td colspan="17">5. Повороты корпуса при разметке.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина корпуса</td><td colspan="15">Диаметр корпуса Д, мм, до</td></tr>
<tr><td rowspan="2">L, мм, до</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>900</td><td>1100</td><td colspan="2">1400</td><td>1700</td><td>2100</td><td>2600</td><td>3200</td><td>4000</td></tr>
<tr><td colspan="15">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>1000</td><td>5,3</td><td>6,0</td><td>7,3</td><td>8,4</td><td>9,5</td><td>11,0</td><td>12,4</td><td>14,1</td><td colspan="2">16,6</td><td>18,8</td><td>21,7</td><td>24,9</td><td>28,6</td><td>33,1</td></tr>
<tr><td>2</td><td>2000</td><td>5,7</td><td>6,5</td><td>7,8</td><td>9,1</td><td>10,2</td><td>11,9</td><td>13,4</td><td>15,3</td><td colspan="2">17,9</td><td>20,3</td><td>23,4</td><td>26,9</td><td>30,9</td><td>35,8</td></tr>
<tr><td>3</td><td>4000</td><td>6,2</td><td>7,0</td><td>8,4</td><td>9,8</td><td>11,0</td><td>12,8</td><td>14,4</td><td>16,5</td><td colspan="2">19,3</td><td>21,9</td><td>25,2</td><td>29,0</td><td>33,3</td><td>38,6</td></tr>
<tr><td>4</td><td>6000</td><td>7,2</td><td>8,1</td><td>9,8</td><td>11,3</td><td>12,7</td><td>14,8</td><td>16,7</td><td>19,0</td><td colspan="2">22,3</td><td>25,3</td><td>29,1</td><td>33,6</td><td>38,5</td><td>44,6</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="10%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="2%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="11" rowspan="2">Разметка мест установки деталей, узлов</td><td colspan="6">Слесарные работы</td></tr>
<tr><td colspan="6">Карта 51, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина корпуса</td><td colspan="15">Диаметр корпуса Д, мм, до</td></tr>
<tr><td rowspan="2">L, мм, до</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>900</td><td>1100</td><td colspan="2">1400</td><td>1700</td><td>2100</td><td>2600</td><td>3200</td><td>4000</td></tr>
<tr><td colspan="15">Время Т, чел.-мин.</td></tr>
<tr><td>5</td><td>8000</td><td>7,8</td><td>8,8</td><td>10,6</td><td>12,3</td><td>13,9</td><td>16,1</td><td>18,1</td><td>20,7</td><td colspan="2">24,2</td><td>27,5</td><td>31,7</td><td>36,5</td><td>41,8</td><td>48,5</td></tr>
<tr><td>6</td><td>10000</td><td>8,3</td><td>9,4</td><td>11,3</td><td>13,1</td><td>14,8</td><td>17,1</td><td>19,3</td><td>22,1</td><td colspan="2">25,9</td><td>29,4</td><td>33,8</td><td>38,9</td><td>44,6</td><td>51,7</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>


<a id="p103235"></a>*Примечание* I. 1. Работа выполняется бригадой из двух человек:

                                 0,11    0,66
<a id="p103236"></a>                    Т = 0,065 х L     х Д          поз. 1...3;

                                 0,29    0,66
<a id="p103237"></a>                    Т = 0,015 х L     х Д          поз. 4...6.


<table>
<colgroup><col width="15%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="2%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="10" rowspan="2">Разметка мест установки деталей, узлов</td><td colspan="6">Слесарные работы</td></tr>
<tr><td colspan="6">Карта 51, лист 3</td></tr>
<tr><td colspan="16">II. Разметка и нанесение четырех осевых линий на днищах аппаратов</td></tr>
<tr><td colspan="16">Содержание работы</td></tr>
<tr><td colspan="16">1. Наметить центр.</td></tr>
<tr><td colspan="16">2. Провести четыре осевые линии.</td></tr>
<tr><td colspan="16">3. Кернить осевые линии, выделив линию сборки.</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="15">Диаметр днища Д, мм, до</td></tr>
<tr><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>900</td><td>1100</td><td colspan="2">1400</td><td>1700</td><td>2100</td><td>2600</td><td>3200</td><td>4000</td></tr>
<tr><td colspan="15">Время Т, чел.-мин.</td></tr>
<tr><td>7</td><td>4,40</td><td>4,96</td><td>6,0</td><td>7,0</td><td>7,8</td><td>9,1</td><td>10,2</td><td>11,7</td><td colspan="2">13,7</td><td>15,6</td><td>17,9</td><td>20,6</td><td>23,7</td><td>27,4</td></tr>
<tr><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>


<a id="p103250"></a>*Примечания* II. 2. При измененных условиях разметки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="24%"><col width="5%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="5%"><col width="12%"><col width="16%"><col width="11%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="7">Количество осей</td><td colspan="2">Нанесение осевых линий</td></tr>
<tr><td>1</td><td>2</td><td>3</td><td>4</td><td>5</td><td>6</td><td>св. 6</td><td>на сферические днища</td><td>на плоские днища</td></tr>
<tr><td>Коэффициент</td><td>0,4</td><td>0,6</td><td>0,8</td><td>1,0</td><td>1,25</td><td>1,5</td><td>1,2 на одну ось</td><td>1,0</td><td>0,7</td></tr>
</table>


<a id="p103253"></a>II. 3. Работа выполняется бригадой из двух человек:

                                     0,66
<a id="p103254"></a>                        Т = 0,115 х Д       поз. 7.


<table>
<colgroup><col width="7%"><col width="11%"><col width="15%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="2%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="9" rowspan="2">Разметка мест установки деталей, узлов</td><td colspan="6">Слесарные работы</td></tr>
<tr><td colspan="6">Карта 51, лист 4</td></tr>
<tr><td colspan="15">III. Разметка отверстий или площадок под установку арматуры на корпусе в днищах аппарата</td></tr>
<tr><td colspan="15">Содержание работы</td></tr>
<tr><td colspan="15">1. Ознакомиться с расположением арматуры на корпусе и днищах аппарата по чертежу.</td></tr>
<tr><td colspan="15">2. Наметить отверстия или площадки для установки арматуры на ранее размеченных осях.</td></tr>
<tr><td colspan="15">3. Кернить контуры отверстий или площадок с поворотами корпуса при разметке.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Вид детали,</td><td>Размер размечаемых</td><td colspan="12">Диаметр корпуса Д, мм, до</td></tr>
<tr><td rowspan="2">узла</td><td rowspan="2">мест Р, мм, до</td><td>500</td><td>600</td><td>750</td><td>900</td><td>1100</td><td colspan="2">1400</td><td>1700</td><td>2100</td><td>2600</td><td>3200</td><td>4000</td></tr>
<tr><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>8</td><td rowspan="8">Штуцеры, приварыши, смотровые окна и т.д.</td><td>25</td><td>1,84</td><td>1,87</td><td>2,06</td><td>2,24</td><td>2,44</td><td colspan="2">2,72</td><td>2,96</td><td>3,25</td><td>3,57</td><td>3,91</td><td>4,31</td></tr>
<tr><td>9</td><td>75</td><td>2,05</td><td>2,22</td><td>2,45</td><td>2,65</td><td>2,90</td><td colspan="2">3,22</td><td>3,51</td><td>3,85</td><td>4,23</td><td>4,64</td><td>5,10</td></tr>
<tr><td>10</td><td>160</td><td>2,21</td><td>2,39</td><td>2,64</td><td>2,86</td><td>3,13</td><td colspan="2">3,48</td><td>3,79</td><td>4,16</td><td>4,57</td><td>5,00</td><td>5,50</td></tr>
<tr><td>11</td><td>220</td><td>2,30</td><td>2,50</td><td>2,75</td><td>2,98</td><td>3,26</td><td colspan="2">3,63</td><td>3,95</td><td>4,33</td><td>4,76</td><td>5,20</td><td>5,80</td></tr>
<tr><td>12</td><td>300</td><td>2,61</td><td>2,83</td><td>3,12</td><td>3,38</td><td>3,69</td><td colspan="2">4,10</td><td>4,47</td><td>4,90</td><td>5,39</td><td>5,90</td><td>6,51</td></tr>
<tr><td>13</td><td>450</td><td>3,07</td><td>3,32</td><td>3,67</td><td>3,97</td><td>4,34</td><td colspan="2">4,82</td><td>5,30</td><td>5,80</td><td>6,30</td><td>6,90</td><td>7,70</td></tr>
<tr><td>14</td><td>600</td><td>3,44</td><td>3,73</td><td>4,11</td><td>4,46</td><td>4,87</td><td colspan="2">5,40</td><td>5,90</td><td>6,50</td><td>7,10</td><td>7,80</td><td>8,60</td></tr>
<tr><td>15</td><td>820</td><td>3,90</td><td>4,23</td><td>4,70</td><td>5,10</td><td>5,50</td><td colspan="2">6,10</td><td>6,70</td><td>7,30</td><td>8,10</td><td>8,80</td><td>9,70</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="11%"><col width="15%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="2%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="9" rowspan="2">Разметка мест установки деталей, узлов</td><td colspan="6">Слесарные работы</td></tr>
<tr><td colspan="6">Карта 51, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td>Вид детали,</td><td>Размер размечаемых</td><td colspan="12">Диаметр корпуса Д, мм, до</td></tr>
<tr><td rowspan="2">узла</td><td rowspan="2">мест Р, мм, до</td><td>500</td><td>600</td><td>750</td><td>900</td><td>1100</td><td colspan="2">1400</td><td>1700</td><td>2100</td><td>2600</td><td>3200</td><td>4000</td></tr>
<tr><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>16</td><td>Лапы, опоры,</td><td>100</td><td>2,21</td><td>2,39</td><td>2,63</td><td>2,84</td><td>3,10</td><td colspan="2">3,44</td><td>3,74</td><td>4,09</td><td>4,49</td><td>4,9</td><td>5,4</td></tr>
<tr><td>17</td><td>вентиляторы и</td><td>200</td><td>2,45</td><td>2,65</td><td>2,92</td><td>3,16</td><td>3,44</td><td colspan="2">3,82</td><td>4,14</td><td>4,54</td><td>4,98</td><td>5,5</td><td>6,0</td></tr>
<tr><td>18</td><td rowspan="6">т.д.</td><td>400</td><td>2,72</td><td>2,94</td><td>3,24</td><td>3,50</td><td>3,82</td><td colspan="2">4,23</td><td>4,60</td><td>5,04</td><td>5,50</td><td>6,0</td><td>6,7</td></tr>
<tr><td>19</td><td>650</td><td>2,93</td><td>3,16</td><td>3,48</td><td>3,77</td><td>4,10</td><td colspan="2">4,55</td><td>4,95</td><td>5,42</td><td>5,94</td><td>6,5</td><td>7,2</td></tr>
<tr><td>20</td><td>1000</td><td>3,39</td><td>3,67</td><td>4,04</td><td>4,37</td><td>4,76</td><td colspan="2">5,30</td><td>5,70</td><td>6,30</td><td>6,90</td><td>7,5</td><td>8,3</td></tr>
<tr><td>21</td><td>1400</td><td>3,78</td><td>4,09</td><td>4,50</td><td>4,86</td><td>5,30</td><td colspan="2">5,90</td><td>6,40</td><td>7,00</td><td>7,70</td><td>8,4</td><td>9,2</td></tr>
<tr><td>22</td><td>1900</td><td>4,17</td><td>4,51</td><td>4,96</td><td>5,40</td><td>5,90</td><td colspan="2">6,50</td><td>7,10</td><td>7,70</td><td>8,50</td><td>9,3</td><td>10,2</td></tr>
<tr><td>23</td><td>2600</td><td>4,61</td><td>4,98</td><td>5,50</td><td>5,90</td><td>6,50</td><td colspan="2">7,20</td><td>7,80</td><td>8,50</td><td>9,40</td><td>10,2</td><td>11,3</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>


<a id="p103284"></a>Примечания: III. 4. При измененных условиях разметки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="32%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"><col width="12%"><col width="12%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="6">Количество размечаемых мест на одной оси, до</td></tr>
<tr><td>1</td><td>2</td><td>4</td><td>6</td><td>12</td><td>16</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>0,85</td><td>0,7</td><td>0,6</td><td>0,55</td><td>0,5</td></tr>
</table>



<table>
<colgroup><col width="67%"><col width="33%"></colgroup>
<tr><td rowspan="2">Разметка мест установки деталей, узлов</td><td>Слесарные работы</td></tr>
<tr><td>Карта 51, лист 6</td></tr>
</table>


<a id="p103289"></a>III. 5. Работа выполняется бригадой из двух человек:

                              0,44    0,1
<a id="p103290"></a>                Т = 0,0864 х Д     х Р       поз. 8...10;

                              0,44    0,4
<a id="p103291"></a>                Т = 0,0173 х Д     х Р       поз. 11...15;

                              0,43    0,15
<a id="p103292"></a>                Т = 0,0765 х Д     х Р       поз. 16...19;

                              0,43    0,32
<a id="p103293"></a>                Т = 0,0257 х Д     х Р       поз. 20...23;


<table>
<colgroup><col width="9%"><col width="13%"><col width="16%"><col width="9%"><col width="9%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="6" rowspan="2">Разметка деталей из профильного материала под обрезку</td><td colspan="3">Слесарные работы</td></tr>
<tr><td colspan="3">Карта 52, лист 1</td></tr>
<tr><td colspan="9">Содержание работы</td></tr>
<tr><td colspan="9">1. Установить деталь на разметочную плиту.</td></tr>
<tr><td colspan="9">2. Разметить конец детали под обрезку.</td></tr>
<tr><td colspan="9">3. Накернить контрольные риски.</td></tr>
<tr><td colspan="9">4. Снять деталь с плиты, отложить.</td></tr>
<tr><td colspan="9">I. Угловая сталь</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Схема разметки</td><td rowspan="3">Длина детали L, мм, до</td><td colspan="6">N профиля, до</td></tr>
<tr><td>3</td><td>4</td><td>7,5</td><td>10</td><td>16</td><td>25</td></tr>
<tr><td colspan="6">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="7">Схема не приводится</td><td>1,0</td><td>0,61</td><td>0,76</td><td>0,91</td><td>1,04</td><td>1,29</td><td>1,57</td></tr>
<tr><td>2</td><td>2,0</td><td>0,82</td><td>1,03</td><td>1,24</td><td>1,40</td><td>1,73</td><td>2,12</td></tr>
<tr><td>3</td><td>4,0</td><td>1,10</td><td>1,38</td><td>1,66</td><td>1,89</td><td>2,33</td><td>2,85</td></tr>
<tr><td>4</td><td>6,0</td><td>1,31</td><td>1,64</td><td>1,97</td><td>2,25</td><td>2,78</td><td>3,39</td></tr>
<tr><td>5</td><td>8,0</td><td>1,48</td><td>1,86</td><td>2,24</td><td>2,54</td><td>3,14</td><td>3,84</td></tr>
<tr><td>6</td><td>10,0</td><td>-</td><td>2,05</td><td>2,46</td><td>2,80</td><td>3,46</td><td>4,23</td></tr>
<tr><td>7</td><td>12,0</td><td>-</td><td>-</td><td>2,66</td><td>3,03</td><td>3,74</td><td>4,57</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="9%"><col width="13%"><col width="16%"><col width="9%"><col width="9%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="6" rowspan="2">Разметка деталей из профильного материала под обрезку</td><td colspan="3">Слесарные работы</td></tr>
<tr><td colspan="3">Карта 52, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Схема разметки</td><td rowspan="3">Длина детали L, м, до</td><td colspan="6">N профиля, до</td></tr>
<tr><td>3</td><td>5</td><td>7,5</td><td>10</td><td>16</td><td>25</td></tr>
<tr><td colspan="6">Время Т, чел.-мин.</td></tr>
<tr><td>8</td><td rowspan="7">Схема не приводится</td><td>1,0</td><td>1,00</td><td>1,25</td><td>1,49</td><td>1,69</td><td>2,08</td><td>2,54</td></tr>
<tr><td>9</td><td>2,0</td><td>1,23</td><td>1,54</td><td>1,84</td><td>2,09</td><td>2,56</td><td>3,12</td></tr>
<tr><td>10</td><td>4,0</td><td>1,51</td><td>1,89</td><td>2,26</td><td>2,57</td><td>3,16</td><td>3,84</td></tr>
<tr><td>11</td><td>6,0</td><td>1,71</td><td>2,14</td><td>2,56</td><td>2,90</td><td>3,57</td><td>4,34</td></tr>
<tr><td>12</td><td>8,0</td><td>1,86</td><td>2,33</td><td>2,79</td><td>3,16</td><td>3,89</td><td>4,73</td></tr>
<tr><td>13</td><td>10,0</td><td>-</td><td>2,49</td><td>2,98</td><td>3,38</td><td>4,16</td><td>5,06</td></tr>
<tr><td>14</td><td>12,0</td><td>-</td><td>-</td><td>3,15</td><td>3,57</td><td>4,39</td><td>5,34</td></tr>
<tr><td>15</td><td rowspan="7">Схема не приводится</td><td>1,0</td><td>0,86</td><td>1,07</td><td>1,28</td><td>1,46</td><td>1,79</td><td>2,18</td></tr>
<tr><td>16</td><td>2,0</td><td>1,06</td><td>1,32</td><td>1,58</td><td>1,79</td><td>2,20</td><td>2,68</td></tr>
<tr><td>17</td><td>4,0</td><td>1,30</td><td>1,63</td><td>1,94</td><td>2,21</td><td>2,71</td><td>3,30</td></tr>
<tr><td>18</td><td>6,0</td><td>1,17</td><td>1,84</td><td>2,19</td><td>2,49</td><td>3,06</td><td>3,73</td></tr>
<tr><td>19</td><td>8,0</td><td>1,60</td><td>2,00</td><td>2,39</td><td>2,71</td><td>3,34</td><td>4,06</td></tr>
<tr><td>20</td><td>10,0</td><td>-</td><td>2,14</td><td>2,56</td><td>2,90</td><td>3,57</td><td>4,34</td></tr>
<tr><td>21</td><td>12,0</td><td>-</td><td>-</td><td>2,70</td><td>3,07</td><td>3,77</td><td>4,59</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="9%"><col width="13%"><col width="16%"><col width="9%"><col width="9%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="6" rowspan="2">Разметка деталей из профильного материала под обрезку</td><td colspan="3">Слесарные работы</td></tr>
<tr><td colspan="3">Карта 52, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Схема разметки</td><td rowspan="3">Длина детали L, м, до</td><td colspan="6">N профиля, до</td></tr>
<tr><td>3</td><td>5</td><td>7,5</td><td>10</td><td>16</td><td>25</td></tr>
<tr><td colspan="6">Время Т, чел.-мин.</td></tr>
<tr><td>22</td><td rowspan="7">Схема не приводится</td><td>1,0</td><td>0,94</td><td>1,18</td><td>1,41</td><td>1,60</td><td>1,97</td><td>2,40</td></tr>
<tr><td>23</td><td>2,0</td><td>1,16</td><td>1,45</td><td>1,74</td><td>1,97</td><td>2,42</td><td>2,95</td></tr>
<tr><td>24</td><td>4,0</td><td>1,43</td><td>1,79</td><td>2,14</td><td>2,43</td><td>2,98</td><td>3,63</td></tr>
<tr><td>25</td><td>6,0</td><td>1,47</td><td>2,02</td><td>2,41</td><td>2,74</td><td>3,37</td><td>4,10</td></tr>
<tr><td>26</td><td>8,0</td><td>1,76</td><td>2,20</td><td>2,63</td><td>2,99</td><td>3,67</td><td>4,47</td></tr>
<tr><td>27</td><td>10,0</td><td>-</td><td>2,35</td><td>2,81</td><td>3,19</td><td>3,93</td><td>4,78</td></tr>
<tr><td>28</td><td>12,0</td><td>-</td><td>-</td><td>2,97</td><td>3,37</td><td>4,15</td><td>5,05</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="9%"><col width="13%"><col width="16%"><col width="9%"><col width="9%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="6" rowspan="2">Разметка деталей из профильного материала под обрезку</td><td colspan="3">Слесарные работы</td></tr>
<tr><td colspan="3">Карта 52, лист 4</td></tr>
<tr><td colspan="9">II. Стальной швеллер</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Схема разметки</td><td rowspan="3">Длина детали L, м, до</td><td colspan="6">N профиля, до</td></tr>
<tr><td>8</td><td>14</td><td>22</td><td>30</td><td>40</td><td>50</td></tr>
<tr><td colspan="6">Время Т, чел.-мин.</td></tr>
<tr><td>29</td><td rowspan="7">Схема не приводится</td><td>1,0</td><td>1,12</td><td>1,33</td><td>1,54</td><td>1,70</td><td>1,87</td><td>2,00</td></tr>
<tr><td>30</td><td>2,0</td><td>1,47</td><td>1,76</td><td>2,03</td><td>2,25</td><td>2,46</td><td>2,64</td></tr>
<tr><td>31</td><td>4,0</td><td>1,94</td><td>2,32</td><td>2,68</td><td>2,96</td><td>3,25</td><td>3,49</td></tr>
<tr><td>32</td><td>6,0</td><td>2,28</td><td>2,73</td><td>3,16</td><td>3,48</td><td>3,82</td><td>4,10</td></tr>
<tr><td>33</td><td>8,0</td><td>2,56</td><td>3,06</td><td>3,54</td><td>3,91</td><td>4,29</td><td>4,60</td></tr>
<tr><td>34</td><td>10,0</td><td>-</td><td>3,35</td><td>3,87</td><td>4,27</td><td>4,69</td><td>5,03</td></tr>
<tr><td>35</td><td>12,0</td><td>-</td><td>-</td><td>4,16</td><td>4,60</td><td>5,04</td><td>5,42</td></tr>
<tr><td>36</td><td rowspan="7">Схема не приводится</td><td>1,0</td><td>1,91</td><td>2,28</td><td>2,64</td><td>2,91</td><td>3,19</td><td>3,43</td></tr>
<tr><td>37</td><td>2,0</td><td>2,33</td><td>2,79</td><td>3,22</td><td>3,56</td><td>3,90</td><td>4,19</td></tr>
<tr><td>38</td><td>4,0</td><td>2,85</td><td>3,41</td><td>3,94</td><td>4,35</td><td>4,77</td><td>5,12</td></tr>
<tr><td>39</td><td>6,0</td><td>3,21</td><td>3,83</td><td>4,43</td><td>4,89</td><td>5,37</td><td>5,76</td></tr>
<tr><td>40</td><td>8,0</td><td>3,48</td><td>4,17</td><td>4,82</td><td>5,32</td><td>5,83</td><td>6,26</td></tr>
<tr><td>41</td><td>10,0</td><td>-</td><td>4,45</td><td>5,14</td><td>5,68</td><td>6,22</td><td>6,68</td></tr>
<tr><td>42</td><td>12,0</td><td>-</td><td>-</td><td>5,42</td><td>5,98</td><td>6,56</td><td>7,05</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="9%"><col width="13%"><col width="16%"><col width="9%"><col width="9%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="6" rowspan="2">Разметка деталей из профильного материала под обрезку</td><td colspan="3">Слесарные работы</td></tr>
<tr><td colspan="3">Карта 52, лист 5</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Схема разметки</td><td rowspan="3">Длина детали L, м, до</td><td colspan="6">N профиля, до</td></tr>
<tr><td>8</td><td>14</td><td>22</td><td>30</td><td>40</td><td>50</td></tr>
<tr><td colspan="6">Время Т, чел.-мин.</td></tr>
<tr><td>43</td><td rowspan="7">Схема не приводится</td><td>1,0</td><td>3,44</td><td>4,12</td><td>4,76</td><td>5,26</td><td>5,76</td><td>6,19</td></tr>
<tr><td>44</td><td>2,0</td><td>3,90</td><td>4,67</td><td>5,39</td><td>5,95</td><td>6,53</td><td>7,01</td></tr>
<tr><td>45</td><td>4,0</td><td>4,42</td><td>5,29</td><td>6,11</td><td>6,75</td><td>7,40</td><td>7,94</td></tr>
<tr><td>46</td><td>6,0</td><td>4,76</td><td>5,69</td><td>6,57</td><td>7,26</td><td>7,96</td><td>8,55</td></tr>
<tr><td>47</td><td>8,0</td><td>5,01</td><td>5,99</td><td>6,92</td><td>7,64</td><td>8,38</td><td>9,00</td></tr>
<tr><td>48</td><td>10,0</td><td>-</td><td>6,23</td><td>7,20</td><td>7,96</td><td>8,72</td><td>9,37</td></tr>
<tr><td>49</td><td>12,0</td><td>-</td><td>-</td><td>7,44</td><td>8,22</td><td>9,01</td><td>9,68</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="9%"><col width="13%"><col width="16%"><col width="9%"><col width="9%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="6" rowspan="2">Разметка деталей из профильного материала под обрезку</td><td colspan="3">Слесарные работы</td></tr>
<tr><td colspan="3">Карта 52, лист 6</td></tr>
<tr><td colspan="9">III. Двутавровая сталь</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Схема разметки</td><td rowspan="3">Длина детали L, м, до</td><td colspan="6">N профиля, до</td></tr>
<tr><td>8</td><td>14</td><td>22</td><td>30</td><td>40</td><td>50</td></tr>
<tr><td colspan="6">Время Т, чел.-мин.</td></tr>
<tr><td>50</td><td rowspan="7">Схема не приводится</td><td>1,0</td><td>1,73</td><td>2,32</td><td>2,75</td><td>3,09</td><td>3,45</td><td>3,75</td></tr>
<tr><td>51</td><td>2,0</td><td>2,32</td><td>3,23</td><td>3,41</td><td>3,83</td><td>4,28</td><td>4,66</td></tr>
<tr><td>52</td><td>4,0</td><td>2,88</td><td>3,56</td><td>4,22</td><td>4,75</td><td>5,30</td><td>5,77</td></tr>
<tr><td>53</td><td>6,0</td><td>3,26</td><td>4,03</td><td>4,79</td><td>5,39</td><td>6,01</td><td>6,54</td></tr>
<tr><td>54</td><td>8,0</td><td>3,57</td><td>4,41</td><td>5,24</td><td>5,89</td><td>6,57</td><td>7,15</td></tr>
<tr><td>55</td><td>10,0</td><td>-</td><td>4,73</td><td>5,61</td><td>6,31</td><td>7,04</td><td>7,66</td></tr>
<tr><td>56</td><td>12,0</td><td>-</td><td>-</td><td>5,94</td><td>6,68</td><td>7,45</td><td>8,11</td></tr>
<tr><td>57</td><td rowspan="3">Схема не приводится</td><td>1,0</td><td>3,37</td><td>4,03</td><td>4,65</td><td>5,14</td><td>5,63</td><td>6,05</td></tr>
<tr><td>58</td><td>2,0</td><td>3,89</td><td>4,66</td><td>5,38</td><td>5,94</td><td>6,52</td><td>7,00</td></tr>
<tr><td>59</td><td>4,0</td><td>4,50</td><td>5,39</td><td>6,22</td><td>6,87</td><td>7,54</td><td>8,09</td></tr>
<tr><td>60</td><td rowspan="4">Схема не приводится</td><td>6,0</td><td>4,90</td><td>5,86</td><td>6,78</td><td>7,48</td><td>8,21</td><td>8,81</td></tr>
<tr><td>61</td><td>8,0</td><td>5,21</td><td>6,23</td><td>7,20</td><td>7,95</td><td>8,72</td><td>9,36</td></tr>
<tr><td>62</td><td>10,0</td><td>-</td><td>6,53</td><td>7,54</td><td>8,33</td><td>9,14</td><td>9,81</td></tr>
<tr><td>63</td><td>12,0</td><td>-</td><td>-</td><td>7,84</td><td>8,66</td><td>9,49</td><td>10,2</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="7%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"></colgroup>
<tr><td colspan="11" rowspan="2">Разметка деталей из профильного материала под обрезку</td><td colspan="5">Слесарные работы</td></tr>
<tr><td colspan="5">Карта 52, лист 7</td></tr>
<tr><td colspan="16">IV. Трубы</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Схема разметки</td><td>Длина детали</td><td colspan="13">Наружный диаметр трубы Д, мм, до</td></tr>
<tr><td rowspan="2">L, м, до</td><td>30</td><td>40</td><td>50</td><td>70</td><td>90</td><td>110</td><td>130</td><td>170</td><td>220</td><td>270</td><td>325</td><td>400</td><td>500</td></tr>
<tr><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>64</td><td>Схема</td><td>3,0</td><td>0,28</td><td>0,36</td><td>0,44</td><td>0,60</td><td>0,75</td><td>0,90</td><td>1,05</td><td>1,33</td><td>1,68</td><td>2,02</td><td>2,39</td><td>2,88</td><td>3,52</td></tr>
<tr><td>65</td><td>не</td><td>5,0</td><td>0,37</td><td>0,48</td><td>0,59</td><td>0,80</td><td>1,00</td><td>1,20</td><td>1,40</td><td>1,78</td><td>2,25</td><td>2,70</td><td>3,19</td><td>3,85</td><td>4,70</td></tr>
<tr><td>66</td><td>при-</td><td>7,0</td><td>0,45</td><td>0,59</td><td>0,72</td><td>0,97</td><td>1,22</td><td>1,46</td><td>1,70</td><td>2,16</td><td>2,72</td><td>3,27</td><td>3,87</td><td>4,66</td><td>5,70</td></tr>
<tr><td>67</td><td>во-</td><td>9,0</td><td>0,52</td><td>0,68</td><td>0,83</td><td>1,12</td><td>1,41</td><td>1,68</td><td>1,96</td><td>2,49</td><td>3,14</td><td>3,78</td><td>4,46</td><td>5,38</td><td>6,57</td></tr>
<tr><td>68</td><td>дится</td><td>12,0</td><td>0,62</td><td>0,80</td><td>0,98</td><td>1,32</td><td>1,66</td><td>1,98</td><td>2,31</td><td>2,94</td><td>3,70</td><td>4,45</td><td>5,26</td><td>6,34</td><td>7,75</td></tr>
<tr><td>69</td><td>Схема</td><td>3,0</td><td>1,10</td><td>1,33</td><td>1,54</td><td>1,92</td><td>2,27</td><td>2,59</td><td>2,89</td><td>3,45</td><td>4,09</td><td>4,68</td><td>5,29</td><td>6,06</td><td>6,78</td></tr>
<tr><td>70</td><td>не</td><td>5,0</td><td>1,31</td><td>1,58</td><td>1,83</td><td>2,28</td><td>2,70</td><td>3,08</td><td>3,44</td><td>4,10</td><td>4,86</td><td>5,56</td><td>6,29</td><td>7,21</td><td>8,08</td></tr>
<tr><td>71</td><td>при-</td><td>7,0</td><td>1,46</td><td>1,77</td><td>2,05</td><td>2,56</td><td>3,02</td><td>3,45</td><td>3,85</td><td>4,60</td><td>5,45</td><td>6,24</td><td>7,05</td><td>8,09</td><td>9,06</td></tr>
<tr><td>72</td><td>во-</td><td>9,0</td><td>1,60</td><td>1,93</td><td>2,33</td><td>2,79</td><td>3,29</td><td>3,76</td><td>4,20</td><td>5,01</td><td>5,94</td><td>6,80</td><td>7,68</td><td>8,81</td><td>9,96</td></tr>
<tr><td>73</td><td>дится</td><td>12,0</td><td>1,76</td><td>2,13</td><td>2,46</td><td>3,07</td><td>3,63</td><td>4,14</td><td>4,63</td><td>5,52</td><td>6,55</td><td>7,49</td><td>8,47</td><td>9,71</td><td>10,87</td></tr>
<tr><td>74</td><td>Схема</td><td>3,0</td><td>1,33</td><td>1,61</td><td>1,86</td><td>2,33</td><td>2,75</td><td>3,14</td><td>3,50</td><td>4,18</td><td>4,95</td><td>5,67</td><td>6,41</td><td>7,35</td><td>8,22</td></tr>
<tr><td>75</td><td>не</td><td>5,0</td><td>1,58</td><td>1,91</td><td>2,22</td><td>2,77</td><td>3,27</td><td>3,73</td><td>4,17</td><td>4,97</td><td>5,89</td><td>6,75</td><td>7,63</td><td>8,75</td><td>9,79</td></tr>
<tr><td>76</td><td>при-</td><td>7,0</td><td>1,77</td><td>2,15</td><td>2,49</td><td>3,10</td><td>3,66</td><td>4,18</td><td>4,67</td><td>5,57</td><td>6,61</td><td>7,66</td><td>8,55</td><td>9,81</td><td>10,98</td></tr>
<tr><td>77</td><td>во-</td><td>9,0</td><td>1,93</td><td>2,34</td><td>2,71</td><td>3,38</td><td>3,99</td><td>4,56</td><td>5,09</td><td>6,07</td><td>7,20</td><td>8,24</td><td>9,31</td><td>10,7</td><td>11,96</td></tr>
<tr><td>78</td><td>дится</td><td>12,0</td><td>2,13</td><td>2,58</td><td>2,99</td><td>3,73</td><td>4,40</td><td>5,02</td><td>5,61</td><td>6,70</td><td>7,94</td><td>9,09</td><td>10,3</td><td>11,8</td><td>13,19</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="69%"><col width="31%"></colgroup>
<tr><td rowspan="2">Разметка деталей из профильного материала под обрезку</td><td>Слесарные работы</td></tr>
<tr><td>Карта 52, лист 8</td></tr>
</table>


<a id="p103409"></a>Примечания:
1. <a id="p103410"></a>При измененных условиях разметки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="15%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"><col width="14%"><col width="15%"><col width="7%"><col width="7%"></colgroup>
<tr><td>Факторы, влияющие</td><td colspan="8">Разметка</td></tr>
<tr><td>на изменение нормы времени</td><td>одного конца детали прямого профиля</td><td>двух концов детали прямого профиля</td><td>одного конца гнутого профиля</td><td>двух концов гнутого профиля</td><td>одной детали на одной заготовке</td><td>нескольких деталей на одной заготовке</td><td>по чертежу</td><td>по шаблону</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,3</td><td>1,2</td><td>1,4</td><td>1,0</td><td>0,6</td><td>1,0</td><td>0,65</td></tr>
</table>


2. <a id="p103413"></a>Работа выполняется одним человеком:

                             0,43    0,45
<a id="p103414"></a>                Т = 0,369 х L     х N        поз. 1...7;

                             0,3    0,44
<a id="p103415"></a>                Т = 0,615 х L    х N         поз. 8...14;

                             0,3    0,44
<a id="p103416"></a>                Т = 0,528 х L    х N         поз. 15...21;

                             0,3    0,44
<a id="p103417"></a>                Т = 0,581 х L    х N         поз. 22...28;

                             0,4    0,32
<a id="p103418"></a>                Т = 0,573 х L    х N         поз. 29...35;

                            0,29    0,32
<a id="p103419"></a>                Т = 0,98 х L     х N         поз. 36...42;


                            0,18    0,32
<a id="p103420"></a>                Т = 1,77 х L     х N         поз. 43...49;

                             0,31    0,38
<a id="p103421"></a>                Т = 0,849 х L     х N        поз. 50...56;

                            0,21    0,32
<a id="p103422"></a>                Т = 1,73 х L     х N         поз. 57...63;

                             0,57    0,9
<a id="p103423"></a>                Т = 0,007 х L     х Д        поз. 64...68;

                            0,34    0,66
<a id="p103424"></a>                Т = 0,08 х L     х Д         поз. 69...73;

                             0,34    0,66
<a id="p103425"></a>                Т = 0,097 х L     х Д        поз. 74...78.


<table>
<colgroup><col width="8%"><col width="12%"><col width="12%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Разметка днища и обечаек под обрезку</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 53, лист 1</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">I. Разметка рейсмусом</td></tr>
<tr><td colspan="13">1. Взять инструмент и приспособления.</td></tr>
<tr><td colspan="13">2. Рассчитать высоту борта днища или линию обрезки обечайки.</td></tr>
<tr><td colspan="13">3. Наметить линию под обрезку.</td></tr>
<tr><td colspan="13">4. Накернить линию под обрезку (для случая с кернением).</td></tr>
<tr><td colspan="13">II. Наметка по шаблону линейкой, рулеткой</td></tr>
<tr><td colspan="13">1. Взять шаблон, наложить на днище или обечайку.</td></tr>
<tr><td colspan="13">2. Выверить положение шаблона.</td></tr>
<tr><td colspan="13">3. Очертить контур, снять шаблон.</td></tr>
<tr><td colspan="13">4. Наметить линию под обрезку.</td></tr>
<tr><td colspan="13">5. Накернить линию под обрезку (для случая с кернением).</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Способ разметки</td><td colspan="10">Диаметр днища или обечайки Д, мм, до</td></tr>
<tr><td>300</td><td>450</td><td>600</td><td>800</td><td>1050</td><td>1400</td><td>1800</td><td>2300</td><td>3000</td><td>4000</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="2">Разметка рейсмусом</td><td>с кернением</td><td>1,55</td><td>2,31</td><td>3,06</td><td>4,06</td><td>5,30</td><td>7,02</td><td>8,99</td><td>11,43</td><td>14,83</td><td>19,65</td></tr>
<tr><td>2</td><td>без кернения</td><td>0,72</td><td>0,94</td><td>1,36</td><td>1,78</td><td>2,28</td><td>2,97</td><td>3,75</td><td>4,69</td><td>5,99</td><td>7,81</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="12%"><col width="12%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Разметка днища и обечаек под обрезку</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 53, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Способ разметки</td><td colspan="10">Диаметр днища или обечайки Д, мм, до</td></tr>
<tr><td>300</td><td>450</td><td>600</td><td>800</td><td>1050</td><td>1400</td><td>1800</td><td>2300</td><td>3000</td><td>4000</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>3</td><td rowspan="2">Наметка по шаблону</td><td>с кернением</td><td>1,31</td><td>1,95</td><td>2,59</td><td>3,43</td><td>4,48</td><td>5,93</td><td>7,59</td><td>9,65</td><td>12,52</td><td>16,60</td></tr>
<tr><td>4</td><td>без кернения</td><td>0,45</td><td>0,59</td><td>0,86</td><td>1,12</td><td>1,43</td><td>1,87</td><td>2,35</td><td>2,95</td><td>3,76</td><td>4,90</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>


<a id="p103450"></a>*Примечание.* Работа выполняется одним человеком:

                                     0,98
<a id="p103451"></a>                       Т = 0,0058 х Д        поз. 1;

                                      0,92
<a id="p103452"></a>                       Т = 0,00379 х Д       поз. 2;

                                     0,98
<a id="p103453"></a>                       Т = 0,0049 х Д        поз. 3;

                                      0,92
<a id="p103454"></a>                       Т = 0,00238 х Д       поз. 4;


<table>
<colgroup><col width="12%"><col width="20%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="5%"><col width="4%"><col width="9%"><col width="11%"></colgroup>
<tr><td colspan="7" rowspan="2">Кернение очерченного контура и кернение центров отверстий</td><td colspan="3">Слесарные работы</td></tr>
<tr><td colspan="3">Карта 54</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Взять керн и молоток. (рисунок не</td></tr>
<tr><td colspan="10">2. Кернить очерченный контур или центр отверстия. приводится)</td></tr>
<tr><td colspan="10">3. Отложить инструмент.</td></tr>
<tr><td colspan="10">I. Окернивание контура</td></tr>
<tr><td rowspan="3">N позиции</td><td>Положение размечаемой</td><td colspan="8">Шаг кернения S, мм, до</td></tr>
<tr><td rowspan="2">поверхности</td><td>10</td><td>12</td><td>16</td><td>20</td><td colspan="2">25</td><td>32</td><td>40</td></tr>
<tr><td colspan="8">Время на 1 м Т, чел.-мин.</td></tr>
<tr><td>1</td><td>Горизонтальное</td><td>2,78</td><td>2,35</td><td>1,80</td><td>1,47</td><td colspan="2">1,20</td><td>0,95</td><td>0,78</td></tr>
<tr><td>2</td><td>Вертикальное</td><td>3,30</td><td>2,79</td><td>2,19</td><td>1,74</td><td colspan="2">1,42</td><td>1,13</td><td>0,92</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="15%"><col width="15%"><col width="15%"><col width="15%"><col width="15%"><col width="14%"></colgroup>
<tr><td colspan="7">II. Кернение центров отверстий</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="6">Количество накерниваемых точек n, шт., до</td></tr>
<tr><td>1</td><td>2</td><td>3</td><td>4</td><td>5</td><td>6</td></tr>
<tr><td colspan="6">Время Т, чел.-мин.</td></tr>
<tr><td>3</td><td>0,09</td><td>0,15</td><td>0,19</td><td>0,23</td><td>0,27</td><td>0,31</td></tr>
<tr><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td></tr>
</table>


<a id="p103470"></a>Примечания:
1. <a id="p103471"></a>При измененных условиях кернения приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="26%"><col width="16%"><col width="20%"><col width="19%"><col width="19%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="2">Материал</td><td colspan="2">Вид контура</td></tr>
<tr><td>времени</td><td>сталь</td><td>цветные сплавы</td><td>прямолинейный</td><td>криволинейный</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,2</td></tr>
</table>


2. <a id="p103474"></a>Работа выполняется одним человеком:

                    23,1                   27,4
<a id="p103475"></a>                Т = ----- поз. 1;      Т = ----- поз. 2.
                     0,92                   0,92
                    S                      S


<table>
<colgroup><col width="7%"><col width="9%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="2%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="10" rowspan="2">Маркирование деталей, узлов</td><td colspan="6">Слесарные работы</td></tr>
<tr><td colspan="6">Карта 55, лист 1</td></tr>
<tr><td colspan="16">Содержание работы</td></tr>
<tr><td colspan="16">1. Взять маркировочный инструмент. (рисунок не</td></tr>
<tr><td colspan="16">2. Маркировать деталь, узел. приводится)</td></tr>
<tr><td colspan="16">3. Сменить маркировочный инструмент.</td></tr>
<tr><td colspan="16">4. Повторить приемы 2 - 3 по количеству знаков.</td></tr>
<tr><td colspan="16">5. Отложить маркировочный инструмент.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Метод маркирования</td><td rowspan="3">Вид поверхности</td><td>Высота знака,</td><td colspan="12">Количество знаков n, шт., до</td></tr>
<tr><td rowspan="2">мм</td><td>4</td><td>5</td><td>6</td><td>8</td><td>10</td><td colspan="2">12</td><td>14</td><td>17</td><td>20</td><td>23</td><td>26</td></tr>
<tr><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>Ударным клеймом</td><td rowspan="2">Плоская</td><td>до 5</td><td>0,26</td><td>0,30</td><td>0,34</td><td>0,41</td><td>0,47</td><td colspan="2">0,53</td><td>0,59</td><td>0,67</td><td>0,74</td><td>0,81</td><td>0,88</td></tr>
<tr><td>2</td><td rowspan="3">без подбора</td><td>св. 5</td><td>0,35</td><td>0,40</td><td>0,46</td><td>0,55</td><td>0,63</td><td colspan="2">0,71</td><td>0,79</td><td>0,90</td><td>1,00</td><td>1,09</td><td>1,18</td></tr>
<tr><td>3</td><td rowspan="2">Цилиндрическая</td><td>до 5</td><td>0,29</td><td>0,33</td><td>0,38</td><td>0,45</td><td>0,52</td><td colspan="2">0,59</td><td>0,65</td><td>0,74</td><td>0,82</td><td>0,90</td><td>0,97</td></tr>
<tr><td>4</td><td>св. 5</td><td>0,40</td><td>0,46</td><td>0,52</td><td>0,63</td><td>0,72</td><td colspan="2">0,81</td><td>0,90</td><td>1,02</td><td>1,14</td><td>1,24</td><td>1,35</td></tr>
<tr><td>5</td><td>Ударным клеймом</td><td rowspan="2">Плоская</td><td>до 5</td><td>0,38</td><td>0,44</td><td>0,49</td><td>0,60</td><td>0,69</td><td colspan="2">0,77</td><td>0,86</td><td>0,97</td><td>1,08</td><td>1,18</td><td>1,28</td></tr>
<tr><td>6</td><td rowspan="3">с подбором</td><td>св. 5</td><td>0,50</td><td>0,58</td><td>0,65</td><td>0,78</td><td>0,91</td><td colspan="2">1,02</td><td>1,13</td><td>1,28</td><td>1,42</td><td>1,66</td><td>1,69</td></tr>
<tr><td>7</td><td rowspan="2">Цилиндрическая</td><td>до 5</td><td>0,44</td><td>0,51</td><td>0,57</td><td>0,69</td><td>0,80</td><td colspan="2">0,90</td><td>0,99</td><td>1,12</td><td>1,25</td><td>1,37</td><td>1,48</td></tr>
<tr><td>8</td><td>св. 5</td><td>0,59</td><td>0,69</td><td>0,77</td><td>0,93</td><td>1,08</td><td colspan="2">1,21</td><td>1,34</td><td>1,52</td><td>1,69</td><td>1,85</td><td>2,00</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="9%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="2%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="10" rowspan="2">Маркирование деталей, узлов</td><td colspan="6">Слесарные работы</td></tr>
<tr><td colspan="6">Карта 55, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Метод маркирования</td><td rowspan="3">Вид поверхности</td><td>Высота знака,</td><td colspan="12">Количество знаков n, шт., до</td></tr>
<tr><td rowspan="2">мм, до</td><td>4</td><td>5</td><td>6</td><td>8</td><td>10</td><td colspan="2">12</td><td>14</td><td>17</td><td>20</td><td>23</td><td>26</td></tr>
<tr><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>9</td><td rowspan="2">Краской по трафарету</td><td>Плоская</td><td>60</td><td>0,18</td><td>0,20</td><td>0,23</td><td>0,27</td><td>0,31</td><td colspan="2">0,35</td><td>0,38</td><td>0,43</td><td>0,47</td><td>0,51</td><td>0,55</td></tr>
<tr><td>10</td><td>Цилиндрическая</td><td>60</td><td>0,20</td><td>0,23</td><td>0,26</td><td>0,31</td><td>0,35</td><td colspan="2">0,40</td><td>0,43</td><td>0,49</td><td>0,54</td><td>0,58</td><td>0,63</td></tr>
<tr><td>11</td><td>Краской без</td><td>Плоская</td><td>60</td><td>0,21</td><td>0,24</td><td>0,27</td><td>0,32</td><td>0,36</td><td colspan="2">0,41</td><td>0,44</td><td>0,50</td><td>0,55</td><td>0,60</td><td>0,64</td></tr>
<tr><td>12</td><td>трафарета</td><td>Цилиндрическая</td><td>60</td><td>0,27</td><td>0,31</td><td>0,34</td><td>0,41</td><td>0,47</td><td colspan="2">0,52</td><td>0,57</td><td>0,64</td><td>0,71</td><td>0,77</td><td>0,83</td></tr>
<tr><td colspan="2"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>


<a id="p103502"></a>Примечания:
1. <a id="p103503"></a>При маркировании наборным клеймом время на группу знаков брать в размере 0,2 мин.
2. <a id="p103504"></a>При измененных условиях маркировки приведенное в нормативной карте время применяется с коэффициентами:


<a id="p103507"></a><a id="p103508"></a><a id="p103509"></a><a id="p103510"></a><a id="p103511"></a><a id="p103512"></a><a id="p103513"></a>

<table>
<colgroup><col width="38%"><col width="31%"><col width="31%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="2">Материал</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td></tr>
<tr><td>3. Работа выполняется одним человеком:</td><td></td><td></td></tr>
<tr><td>0,65 Т = 0,1056 х n поз. 1;</td><td>Т = 0,178 х n</td><td>0,65 поз. 7;</td></tr>
<tr><td>0,65 Т = 0,142 х n поз. 2;</td><td>Т = 0,241 х n</td><td>0,65 поз. 8;</td></tr>
<tr><td>0,65 Т = 0,117 х n поз. 3;</td><td>Т = 0,078 х n</td><td>0,6 поз. 9;</td></tr>
<tr><td>0,65 Т = 0,162 х n поз. 4;</td><td>Т = 0,089 х n</td><td>0,6 поз. 10;</td></tr>
<tr><td>0,65 Т = 0,154 х n поз. 5;</td><td>Т = 0,091 х n</td><td>0,6 поз. 11;</td></tr>
<tr><td>0,65 Т = 0,203 х n поз. 6;</td><td>Т = 0,117 х n</td><td>0,6 поз. 12.</td></tr>
</table>



<table>
<colgroup><col width="14%"><col width="28%"><col width="24%"><col width="34%"></colgroup>
<tr><td colspan="3" rowspan="2">Пломбирование и навешивание бирок</td><td>Слесарные работы</td></tr>
<tr><td>Карта 56</td></tr>
<tr><td colspan="4">Содержание работы</td></tr>
<tr><td colspan="4">Пломбирование</td></tr>
<tr><td colspan="4">1. Взять проволоку.</td></tr>
<tr><td colspan="4">2. Протянуть проволоку через отверстие пломбируемой детали.</td></tr>
<tr><td colspan="4">3. Взять пломбу и пломбир.</td></tr>
<tr><td colspan="4">4. Надеть пломбу и опломбировать.</td></tr>
<tr><td colspan="4">5. Скрутить концы проволоки и откусить излишки.</td></tr>
<tr><td colspan="4">6. Отложить инструмент.</td></tr>
<tr><td colspan="4">Навешивание бирок</td></tr>
<tr><td colspan="4">1. Взять шпагат и бирку.</td></tr>
<tr><td colspan="4">2. Протянуть шпагат в отверстие бирки.</td></tr>
<tr><td colspan="4">3. Закрепить бирку на детали.</td></tr>
<tr><td>N позиции</td><td>Вид работы</td><td colspan="2">Время на одну пломбу, бирку Т, чел.-мин.</td></tr>
<tr><td>1</td><td>Пломбирование</td><td colspan="2">0,28</td></tr>
<tr><td>2</td><td>Навешивание бирок</td><td colspan="2">0,20</td></tr>
<tr><td></td><td>Индекс</td><td colspan="2">а</td></tr>
</table>


<a id="p103532"></a>*Примечание.* Работа выполняется одним человеком.


<table>
<colgroup><col width="8%"><col width="8%"><col width="3%"><col width="5%"><col width="5%"><col width="3%"><col width="12%"><col width="14%"><col width="3%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="9" rowspan="2">Подгонка и стыкование кромок</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 57, лист 1</td></tr>
<tr><td colspan="14">Содержание работы</td></tr>
<tr><td colspan="14">1. Зачистить стыкуемые кромки под сварку.</td></tr>
<tr><td colspan="14">2. Взять инструмент и сборочные приспособления.</td></tr>
<tr><td colspan="14">3. Подогнать и выровнять стыкуемые кромки под сварку, выдержав размеры.</td></tr>
<tr><td colspan="14">4. Обжать кромки собираемого изделия и прихватить электросваркой.</td></tr>
<tr><td colspan="14">5. Отложить инструмент и сборочные приспособления.</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="5" rowspan="3">Способ стыкования</td><td rowspan="3">Виды кромок</td><td colspan="3" rowspan="3">Положение стыкуемых кромок</td><td colspan="4">Толщина листа h, мм, до</td></tr>
<tr><td>7</td><td>11</td><td>16</td><td>24</td></tr>
<tr><td colspan="4">Время на 1 м кромки Т, чел.-мин.</td></tr>
<tr><td>1</td><td colspan="5">Встык</td><td rowspan="3">Прямолинейные</td><td colspan="3">Вертикальное</td><td>2,72</td><td>3,47</td><td>4,25</td><td>5,29</td></tr>
<tr><td>2</td><td colspan="2">\\\\\\</td><td colspan="2">//////</td><td></td><td rowspan="2">Горизонтальное</td><td colspan="2">Нижнее</td><td>2,48</td><td>3,16</td><td>3,87</td><td>4,82</td></tr>
<tr><td>3</td><td colspan="5" rowspan="4"></td><td colspan="2">Потолочное</td><td>3,12</td><td>3,98</td><td>4,88</td><td>6,07</td></tr>
<tr><td>4</td><td rowspan="3">Криволинейные</td><td colspan="3">Вертикальное</td><td>2,96</td><td>3,78</td><td>4,63</td><td>5,76</td></tr>
<tr><td>5</td><td rowspan="2">Горизонтальное</td><td colspan="2">Нижнее</td><td>2,72</td><td>3,47</td><td>4,25</td><td>5,29</td></tr>
<tr><td>6</td><td colspan="2">Потолочное</td><td>3,43</td><td>4,38</td><td>5,36</td><td>6,68</td></tr>
<tr><td>7</td><td colspan="5">Внахлестку</td><td rowspan="3">Прямолинейные</td><td colspan="3">Вертикальное</td><td>2,48</td><td>3,16</td><td>3,87</td><td>4,82</td></tr>
<tr><td>8</td><td></td><td colspan="2">\\\\\</td><td colspan="2"></td><td rowspan="2">Горизонтальное</td><td colspan="2">Нижнее</td><td>2,24</td><td>2,86</td><td>3,50</td><td>4,36</td></tr>
<tr><td>9</td><td colspan="5" rowspan="4">/////</td><td colspan="2">Потолочное</td><td>2,72</td><td>3,47</td><td>4,25</td><td>5,29</td></tr>
<tr><td>10</td><td rowspan="3">Криволинейные</td><td colspan="3">Вертикальное</td><td>2,72</td><td>3,47</td><td>4,25</td><td>5,29</td></tr>
<tr><td>11</td><td rowspan="2">Горизонтальное</td><td colspan="2">Нижнее</td><td>2,48</td><td>3,16</td><td>3,87</td><td>4,82</td></tr>
<tr><td>12</td><td colspan="2">Потолочное</td><td>3,12</td><td>3,98</td><td>4,88</td><td>6,07</td></tr>
<tr><td colspan="8"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="4%"><col width="11%"><col width="9%"><col width="12%"><col width="14%"><col width="3%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="7" rowspan="2">Подгонка и стыковка кромок</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 57, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="3" rowspan="3">Способ стыкования</td><td rowspan="3">Виды кромок</td><td colspan="3" rowspan="3">Положение стыкуемых кромок</td><td colspan="4">Толщина листа h, мм, до</td></tr>
<tr><td>7</td><td>11</td><td>16</td><td>24</td></tr>
<tr><td colspan="4">Время на 1 м кромки Т, чел.-мин.</td></tr>
<tr><td>13</td><td colspan="3">Под углом</td><td rowspan="3">Прямолинейные</td><td colspan="3">Вертикальное</td><td>2,56</td><td>3,27</td><td>4,0</td><td>4,98</td></tr>
<tr><td>14</td><td>/ /</td><td colspan="2"></td><td rowspan="2">Горизонтальное</td><td colspan="2">Нижнее</td><td>2,32</td><td>2,96</td><td>3,62</td><td>4,51</td></tr>
<tr><td>15</td><td>/</td><td>\\\\\\</td><td></td><td colspan="2">Потолочное</td><td>2,88</td><td>3,68</td><td>4,50</td><td>5,60</td></tr>
<tr><td>16</td><td colspan="3" rowspan="3"></td><td rowspan="3">Криволинейные</td><td colspan="3">Вертикальное</td><td>2,80</td><td>3,57</td><td>4,38</td><td>5,45</td></tr>
<tr><td>17</td><td rowspan="2">Горизонтальное</td><td colspan="2">Нижнее</td><td>2,56</td><td>3,27</td><td>4,0</td><td>4,98</td></tr>
<tr><td>18</td><td colspan="2">Потолочное</td><td>3,20</td><td>4,08</td><td>5,0</td><td>6,22</td></tr>
<tr><td colspan="6"></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td></tr>
</table>


<a id="p103565"></a>Примечания:
1. <a id="p103566"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="26%"><col width="18%"><col width="18%"><col width="11%"><col width="15%"><col width="14%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="3">Материал</td><td colspan="2">Стыкование кромок</td></tr>
<tr><td>времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>с подгонкой</td><td>без подгонки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p103569"></a>Работа выполняется бригадой из двух человек:

             0,54                                      0,54
<a id="p103570"></a>Т = 0,951 х h        поз. 1, 5, 9, 10;    Т = 0,895 х h        поз. 13, 17;

             0,54                                      0,54
<a id="p103571"></a>Т = 0,867 х h        поз. 2, 7, 11;       Т = 0,811 х h        поз. 14;

             0,54                                      0,54
<a id="p103572"></a>Т = 1,091 х h        поз. 3, 12;          Т = 1,007 х h        поз. 15;

             0,54                                      0,54
<a id="p103573"></a>Т = 1,035 х h        поз. 4;              Т = 0,979 х h        поз. 16;

           0,54                                        0,54
<a id="p103574"></a>Т = 1,2 х h          поз. 6;              Т = 1,119 х h        поз. 18.

             0,54
<a id="p103575"></a>Т = 0,783 х h        поз. 8;


<table>
<colgroup><col width="7%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="15">Подрубка кромок пневматическим зубилом при сборке Слесарные работы</td></tr>
<tr><td colspan="15">Карта 58, лист 1</td></tr>
<tr><td colspan="15">Содержание работы</td></tr>
<tr><td colspan="15">1. Взять инструмент. (рисунок не</td></tr>
<tr><td colspan="15">2. Подрубить кромку. приводится)</td></tr>
<tr><td colspan="15">3. Отложить инструмент.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид кромки</td><td>Ширина кромки</td><td colspan="12">Длина обрубаемой кромки L, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>350</td><td>450</td><td>600</td><td>800</td><td>1000</td><td>1400</td><td>2000</td></tr>
<tr><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="7">Прямолинейная</td><td>4</td><td>0,13</td><td>0,20</td><td>0,26</td><td>0,32</td><td>0,40</td><td>0,56</td><td>0,71</td><td>0,95</td><td>1,25</td><td>1,60</td><td>2,20</td><td>3,15</td></tr>
<tr><td>2</td><td>6</td><td>0,17</td><td>0,27</td><td>0,35</td><td>0,43</td><td>0,53</td><td>0,75</td><td>0,98</td><td>1,25</td><td>1,70</td><td>2,15</td><td>3,00</td><td>4,30</td></tr>
<tr><td>3</td><td>9</td><td>0,23</td><td>0,37</td><td>0,48</td><td>0,58</td><td>0,72</td><td>1,00</td><td>1,30</td><td>1,75</td><td>2,30</td><td>2,90</td><td>4,05</td><td>5,80</td></tr>
<tr><td>4</td><td>12</td><td>0,29</td><td>0,46</td><td>0,59</td><td>0,72</td><td>0,89</td><td>1,25</td><td>1,60</td><td>2,15</td><td>2,85</td><td>3,60</td><td>5,00</td><td>7,15</td></tr>
<tr><td>5</td><td>16</td><td>0,36</td><td>0,55</td><td>0,72</td><td>0,89</td><td>1,10</td><td>1,55</td><td>2,00</td><td>2,55</td><td>3,55</td><td>4,40</td><td>6,20</td><td>8,90</td></tr>
<tr><td>6</td><td>22</td><td>0,46</td><td>0,70</td><td>0,91</td><td>1,10</td><td>1,40</td><td>1,95</td><td>2,55</td><td>3,35</td><td>4,50</td><td>5,60</td><td>7,90</td><td>11,20</td></tr>
<tr><td>7</td><td>30</td><td>0,57</td><td>0,89</td><td>1,15</td><td>1,40</td><td>1,75</td><td>2,45</td><td>3,20</td><td>4,25</td><td>5,60</td><td>7,10</td><td>10,0</td><td>14,10</td></tr>
<tr><td></td><td>Индекс</td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="11%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="15">Подрубка кромок пневматическим зубилом при сборке Слесарные работы</td></tr>
<tr><td colspan="15">Карта 58, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид кромки</td><td>Ширина кромки</td><td colspan="12">Длина обрубаемой кромки L, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td>50</td><td>100</td><td>150</td><td>200</td><td>250</td><td>350</td><td>450</td><td>600</td><td>800</td><td>1000</td><td>1400</td><td>2000</td></tr>
<tr><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>8</td><td rowspan="7">Криволинейная</td><td>4</td><td>0,18</td><td>0,27</td><td>0,34</td><td>0,41</td><td>0,52</td><td>0,73</td><td>0,93</td><td>1,25</td><td>1,65</td><td>2,05</td><td>2,90</td><td>4,15</td></tr>
<tr><td>9</td><td>6</td><td>0,23</td><td>0,36</td><td>0,47</td><td>0,56</td><td>0,70</td><td>0,98</td><td>1,25</td><td>1,65</td><td>2,25</td><td>2,80</td><td>3,90</td><td>5,60</td></tr>
<tr><td>10</td><td>9</td><td>0,30</td><td>0,48</td><td>0,62</td><td>0,76</td><td>0,94</td><td>1,30</td><td>1,70</td><td>2,25</td><td>3,05</td><td>3,70</td><td>5,30</td><td>7,60</td></tr>
<tr><td>11</td><td>12</td><td>0,38</td><td>0,59</td><td>0,76</td><td>0,94</td><td>1,15</td><td>1,60</td><td>2,10</td><td>2,80</td><td>3,75</td><td>4,70</td><td>6,50</td><td>9,40</td></tr>
<tr><td>12</td><td>16</td><td>0,47</td><td>0,72</td><td>0,94</td><td>1,15</td><td>1,45</td><td>2,00</td><td>2,60</td><td>3,45</td><td>4,65</td><td>5,80</td><td>8,10</td><td>11,60</td></tr>
<tr><td>13</td><td>22</td><td>0,60</td><td>0,93</td><td>1,21</td><td>1,45</td><td>1,80</td><td>2,55</td><td>3,30</td><td>4,40</td><td>5,90</td><td>7,30</td><td>10,20</td><td>14,70</td></tr>
<tr><td>14</td><td>30</td><td>0,75</td><td>1,15</td><td>1,50</td><td>1,85</td><td>2,30</td><td>3,21</td><td>4,15</td><td>5,50</td><td>7,40</td><td>9,20</td><td>12,90</td><td>18,50</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>


<a id="p103602"></a>Примечания:
1. <a id="p103603"></a>При измененных условиях подрубки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="17%"><col width="11%"><col width="11%"><col width="11%"><col width="12%"><col width="12%"><col width="13%"><col width="14%"></colgroup>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="4">Подрубка</td></tr>
<tr><td>на изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>глубиной до 4 мм</td><td>глубиной св. 4 мм</td><td>в нижнем положении</td><td>в потолочном положении</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,3</td><td>1,0</td><td>1,3</td></tr>
</table>


2. <a id="p103606"></a>Работа выполняется одним человеком:


<table>
<colgroup><col width="75%"><col width="25%"></colgroup>
<tr><td rowspan="2">Подрубка кромок пневматическим зубилом при сборке</td><td>Слесарные работы</td></tr>
<tr><td>Карта 58, лист 3</td></tr>
</table>


                     0,74    0,64
<a id="p103609"></a>       Т = 0,0038 х В     х L          для L <= 150    поз. 1...7;

                      0,74    0,64
<a id="p103610"></a>       Т = 0,00495 х В     х L         для L <= 150    поз. 8...14;

                       0,75    1,0
<a id="p103611"></a>       Т = 0,000574 х В     х L        для L > 150     поз. 1...7;

                       0,74    1,0
<a id="p103612"></a>       Т = 0,000745 х В     х L        для L > 150     поз. 8...14.


<table>
<colgroup><col width="8%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="2">Сборка плоских листов под сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 59, лист 1</td></tr>
<tr><td colspan="15">Содержание работы</td></tr>
<tr><td colspan="15">1. Подать лист на место сборки, проверить внешним (рисунок не осмотром. приводится)</td></tr>
<tr><td colspan="15">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="15">3. Установить и подогнать листы по стыку, выдержав зазоры и уступность кромок.</td></tr>
<tr><td colspan="15">4. Установить, прихватить сборочные приспособления.</td></tr>
<tr><td colspan="15">5. Прихватить листы электросваркой.</td></tr>
<tr><td colspan="15">6. Срубить сборочные приспособления, зачистить места прихваток.</td></tr>
<tr><td colspan="15">7. Снять лист, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина стыка</td><td>Ширина листа</td><td colspan="12">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">L, мм, до</td><td rowspan="2">В, мм, до</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td colspan="2">24</td><td>35</td><td>55</td><td>80</td><td>110</td></tr>
<tr><td colspan="12">Время на один стык Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">300</td><td>1000</td><td>1,15</td><td>1,43</td><td>1,86</td><td>2,21</td><td>2,93</td><td>3,4</td><td colspan="2">4,2</td><td>5,1</td><td>6,5</td><td>7,9</td><td>9,3</td></tr>
<tr><td>2</td><td>2000</td><td>1,48</td><td>1,82</td><td>2,38</td><td>2,83</td><td>3,75</td><td>4,3</td><td colspan="2">5,4</td><td>6,5</td><td>8,3</td><td>10,0</td><td>11,9</td></tr>
<tr><td>3</td><td>3000</td><td>1,71</td><td>2,12</td><td>2,76</td><td>3,29</td><td>4,35</td><td>5,1</td><td colspan="2">6,2</td><td>7,6</td><td>9,6</td><td>11,7</td><td>13,8</td></tr>
<tr><td>4</td><td>5000</td><td>2,06</td><td>2,55</td><td>3,32</td><td>3,95</td><td>5,20</td><td>6,1</td><td colspan="2">7,5</td><td>9,1</td><td>11,5</td><td>14,0</td><td>16,6</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="2">Сборка плоских листов под сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 59, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина стыка</td><td>Ширина листа</td><td colspan="12">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">L, мм, до</td><td rowspan="2">В, мм, до</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td colspan="2">24</td><td>35</td><td>55</td><td>80</td><td>110</td></tr>
<tr><td colspan="12">Время на один стык Т, чел.-мин.</td></tr>
<tr><td>5</td><td rowspan="4">700</td><td>1000</td><td>1,79</td><td>2,21</td><td>2,89</td><td>3,44</td><td>4,55</td><td>5,9</td><td colspan="2">6,5</td><td>7,9</td><td>10,1</td><td>12,2</td><td>14,4</td></tr>
<tr><td>6</td><td>2000</td><td>2,30</td><td>2,84</td><td>3,71</td><td>4,42</td><td>5,80</td><td>6,8</td><td colspan="2">8,4</td><td>10,2</td><td>12,9</td><td>15,7</td><td>18,5</td></tr>
<tr><td>7</td><td>3000</td><td>2,66</td><td>3,29</td><td>4,29</td><td>5,10</td><td>6,80</td><td>7,9</td><td colspan="2">9,7</td><td>11,8</td><td>14,9</td><td>18,2</td><td>21,4</td></tr>
<tr><td>8</td><td>5000</td><td>3,20</td><td>3,95</td><td>5,20</td><td>6,10</td><td>8,10</td><td>9,4</td><td colspan="2">11,7</td><td>14,2</td><td>17,9</td><td>21,8</td><td>25,7</td></tr>
<tr><td>9</td><td rowspan="4">1000</td><td>1000</td><td>2,16</td><td>2,67</td><td>3,48</td><td>4,1</td><td>5,5</td><td>6,4</td><td colspan="2">7,9</td><td>9,6</td><td>12,1</td><td>14,7</td><td>17,3</td></tr>
<tr><td>10</td><td>2000</td><td>2,77</td><td>3,43</td><td>4,46</td><td>5,3</td><td>7,0</td><td>8,2</td><td colspan="2">10,1</td><td>12,3</td><td>15,5</td><td>18,9</td><td>22,3</td></tr>
<tr><td>11</td><td>3000</td><td>3,21</td><td>3,96</td><td>5,10</td><td>6,1</td><td>8,1</td><td>9,5</td><td colspan="2">11,7</td><td>14,2</td><td>18,0</td><td>21,8</td><td>25,8</td></tr>
<tr><td>12</td><td>5000</td><td>3,85</td><td>4,76</td><td>6,20</td><td>7,4</td><td>9,8</td><td>11,4</td><td colspan="2">14,0</td><td>17,1</td><td>21,6</td><td>26,2</td><td>31,0</td></tr>
<tr><td>13</td><td rowspan="5">1400</td><td>1000</td><td>2,57</td><td>3,18</td><td>4,14</td><td>4,9</td><td>6,5</td><td>7,6</td><td colspan="2">9,4</td><td>11,4</td><td>14,4</td><td>17,6</td><td>20,7</td></tr>
<tr><td>14</td><td>2000</td><td>3,30</td><td>4,08</td><td>5,30</td><td>6,3</td><td>8,4</td><td>9,7</td><td colspan="2">12,0</td><td>14,6</td><td>18,5</td><td>22,5</td><td>26,5</td></tr>
<tr><td>15</td><td>3000</td><td>3,82</td><td>4,72</td><td>6,10</td><td>7,3</td><td>9,7</td><td>11,3</td><td colspan="2">13,9</td><td>16,9</td><td>21,4</td><td>26,0</td><td>30,7</td></tr>
<tr><td>16</td><td>5000</td><td>4,59</td><td>5,70</td><td>7,40</td><td>8,8</td><td>11,7</td><td>13,5</td><td colspan="2">16,7</td><td>20,3</td><td>25,7</td><td>31,3</td><td>36,9</td></tr>
<tr><td>17</td><td>8000</td><td>5,40</td><td>6,70</td><td>8,80</td><td>10,4</td><td>13,8</td><td>16,0</td><td colspan="2">19,8</td><td>24,1</td><td>30,5</td><td>37,0</td><td>43,7</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="2">Сборка плоских листов под сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 59, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина стыка</td><td>Ширина листа</td><td colspan="12">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">L, мм, до</td><td rowspan="2">В, мм, до</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td colspan="2">24</td><td>35</td><td>55</td><td>80</td><td>110</td></tr>
<tr><td colspan="12">Время на один стык Т, чел.-мин.</td></tr>
<tr><td>18</td><td rowspan="5">2000</td><td>1000</td><td>3,10</td><td>3,82</td><td>4,99</td><td>5,9</td><td>7,9</td><td>9,1</td><td colspan="2">11,3</td><td>13,7</td><td>17,3</td><td>21,1</td><td>23,0</td></tr>
<tr><td>19</td><td>2000</td><td>3,97</td><td>4,91</td><td>6,40</td><td>7,6</td><td>10,1</td><td>11,7</td><td colspan="2">14,5</td><td>17,6</td><td>22,3</td><td>27,1</td><td>31,9</td></tr>
<tr><td>20</td><td>3000</td><td>4,60</td><td>5,70</td><td>7,40</td><td>8,8</td><td>11,9</td><td>13,6</td><td colspan="2">16,7</td><td>20,4</td><td>25,8</td><td>31,3</td><td>36,9</td></tr>
<tr><td>21</td><td>5000</td><td>5,50</td><td>6,80</td><td>8,90</td><td>10,6</td><td>14,0</td><td>6,1</td><td colspan="2">20,1</td><td>24,5</td><td>31,0</td><td>37,6</td><td>44,4</td></tr>
<tr><td>22</td><td>8000</td><td>6,50</td><td>8,10</td><td>10,50</td><td>12,6</td><td>16,6</td><td>19,3</td><td colspan="2">23,8</td><td>29,0</td><td>36,7</td><td>44,6</td><td>52,6</td></tr>
<tr><td>23</td><td rowspan="5">2800</td><td>1000</td><td>3,6</td><td>4,5</td><td>5,9</td><td>7,1</td><td>9,4</td><td>10,9</td><td colspan="2">13,4</td><td>16,3</td><td>20,7</td><td>25,1</td><td>29,6</td></tr>
<tr><td>24</td><td>2000</td><td>5,5</td><td>6,8</td><td>8,8</td><td>10,5</td><td>13,9</td><td>16,1</td><td colspan="2">19,9</td><td>24,3</td><td>30,7</td><td>37,3</td><td>44,0</td></tr>
<tr><td>25</td><td>3000</td><td>5,5</td><td>6,8</td><td>8,8</td><td>10,6</td><td>13,9</td><td>16,2</td><td colspan="2">19,9</td><td>24,3</td><td>30,7</td><td>37,3</td><td>44,0</td></tr>
<tr><td>26</td><td>5000</td><td>6,6</td><td>8,1</td><td>10,6</td><td>12,6</td><td>16,7</td><td>19,4</td><td colspan="2">24,0</td><td>29,2</td><td>36,9</td><td>44,8</td><td>52,9</td></tr>
<tr><td>27</td><td>8000</td><td>7,8</td><td>9,6</td><td>12,6</td><td>15,0</td><td>19,8</td><td>23,0</td><td colspan="2">28,4</td><td>34,5</td><td>43,7</td><td>53,1</td><td>62,7</td></tr>
<tr><td>28</td><td rowspan="3">4000</td><td>1000</td><td>-</td><td>5,5</td><td>7,1</td><td>8,5</td><td>11,3</td><td>13,1</td><td colspan="2">16,2</td><td>19,7</td><td>24,9</td><td>30,2</td><td>35,7</td></tr>
<tr><td>29</td><td>2000</td><td>-</td><td>7,0</td><td>9,2</td><td>10,9</td><td>14,5</td><td>16,8</td><td colspan="2">20,7</td><td>25,2</td><td>31,9</td><td>38,8</td><td>45,8</td></tr>
<tr><td>30</td><td>3000</td><td>-</td><td>8,1</td><td>10,6</td><td>12,6</td><td>16,7</td><td>19,4</td><td colspan="2">24,0</td><td>29,2</td><td>36,9</td><td>44,9</td><td>53,0</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="9%"><col width="9%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="2">Сборка плоских листов под сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 59, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина стыка</td><td>Ширина листа</td><td colspan="12">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">L, мм, до</td><td rowspan="2">В, мм, до</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td colspan="2">24</td><td>35</td><td>55</td><td>80</td><td>110</td></tr>
<tr><td colspan="12">Время на один стык Т, чел.-мин.</td></tr>
<tr><td>31</td><td rowspan="3">5600</td><td>1000</td><td>-</td><td>6,5</td><td>8,5</td><td>10,1</td><td>13,4</td><td>15,6</td><td colspan="2">19,3</td><td>23,4</td><td>29,6</td><td>36,0</td><td>42,5</td></tr>
<tr><td>32</td><td>2000</td><td>-</td><td>8,4</td><td>10,9</td><td>13,0</td><td>17,2</td><td>20,0</td><td colspan="2">24,7</td><td>30,1</td><td>38,0</td><td>46,2</td><td>54,5</td></tr>
<tr><td>33</td><td>3000</td><td>-</td><td>9,7</td><td>12,6</td><td>15,1</td><td>19,9</td><td>23,2</td><td colspan="2">28,6</td><td>34,8</td><td>44,0</td><td>53,5</td><td>63,1</td></tr>
<tr><td>34</td><td rowspan="3">8000</td><td>1000</td><td>-</td><td>-</td><td>10,2</td><td>12,2</td><td>16,2</td><td>18,8</td><td colspan="2">23,2</td><td>28,2</td><td>35,9</td><td>43,3</td><td>51,2</td></tr>
<tr><td>35</td><td>2000</td><td>-</td><td>-</td><td>13,2</td><td>15,7</td><td>20,7</td><td>24,1</td><td colspan="2">29,7</td><td>36,2</td><td>45,8</td><td>55,6</td><td>65,7</td></tr>
<tr><td>36</td><td>3000</td><td>-</td><td>-</td><td>15,2</td><td>18,1</td><td>24,0</td><td>27,9</td><td colspan="2">34,4</td><td>41,9</td><td>53,0</td><td>64,4</td><td>76,0</td></tr>
<tr><td>37</td><td rowspan="3">10000</td><td>1000</td><td>-</td><td>-</td><td>-</td><td>13,7</td><td>18,1</td><td>21,1</td><td colspan="2">26,0</td><td>31,7</td><td>40,1</td><td>48,7</td><td>57,5</td></tr>
<tr><td>38</td><td>2000</td><td>-</td><td>-</td><td>-</td><td>17,6</td><td>23,3</td><td>27,1</td><td colspan="2">33,4</td><td>40,6</td><td>51,4</td><td>62,5</td><td>73,7</td></tr>
<tr><td>39</td><td>3000</td><td>-</td><td>-</td><td>-</td><td>20,4</td><td>27,0</td><td>31,3</td><td colspan="2">38,7</td><td>47,0</td><td>59,5</td><td>72,3</td><td>85,3</td></tr>
<tr><td>40</td><td rowspan="3">12000</td><td>1000</td><td>-</td><td>-</td><td>-</td><td>15,1</td><td>20,0</td><td>23,0</td><td colspan="2">28,6</td><td>34,8</td><td>44,0</td><td>53,5</td><td>63,2</td></tr>
<tr><td>41</td><td>2000</td><td>-</td><td>-</td><td>-</td><td>19,4</td><td>25,6</td><td>29,7</td><td colspan="2">36,7</td><td>44,7</td><td>56,5</td><td>68,7</td><td>81,1</td></tr>
<tr><td>42</td><td>3000</td><td>-</td><td>-</td><td>-</td><td>22,4</td><td>29,6</td><td>34,4</td><td colspan="2">42,5</td><td>51,7</td><td>65,4</td><td>79,3</td><td>93,8</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="70%"><col width="30%"></colgroup>
<tr><td rowspan="2">Сборка плоских листов под сварку</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 59, лист 5</td></tr>
</table>


<a id="p103681"></a>Примечания:
1. <a id="p103682"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="26%"><col width="18%"><col width="18%"><col width="11%"><col width="15%"><col width="14%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="3">Материал</td><td colspan="2">Сборка листов</td></tr>
<tr><td>времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>с подгонкой</td><td>без подгонки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p103685"></a>Работа выполняется бригадой из двух человек:

                                    0,52    0,36    0,52
<a id="p103686"></a>                     Т = 0,00345 х L     х В     х h    .


<table>
<colgroup><col width="12%"><col width="20%"><col width="11%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="5" rowspan="2">Сборка полос под сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 60, лист 1</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Подать полосу на место сборки, проверить внешним (рисунок не осмотром. приводится)</td></tr>
<tr><td colspan="10">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="10">3. Установить и подогнать полосы по стыку, выдержав зазоры и уступность кромок.</td></tr>
<tr><td colspan="10">4. Прихватить полосы электросваркой.</td></tr>
<tr><td colspan="10">5. Зачистить места прихваток.</td></tr>
<tr><td colspan="10">6. Снять полосу, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Ширина полосы (размер) стыка</td><td>Длина полосы</td><td colspan="7">Толщина полосы h, мм, до</td></tr>
<tr><td rowspan="2">В, мм, до</td><td rowspan="2">L, мм, до</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>35</td></tr>
<tr><td colspan="7">Время на один стык Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">150</td><td>2000</td><td>1,38</td><td>1,80</td><td>2,13</td><td>2,81</td><td>3,2</td><td>4,0</td><td>4,9</td></tr>
<tr><td>2</td><td>3000</td><td>1,64</td><td>2,13</td><td>2,53</td><td>3,33</td><td>3,8</td><td>4,7</td><td>5,8</td></tr>
<tr><td>3</td><td>5000</td><td>2,04</td><td>2,64</td><td>3,14</td><td>4,10</td><td>4,8</td><td>5,9</td><td>7,1</td></tr>
<tr><td>4</td><td rowspan="3">250</td><td>2000</td><td>1,67</td><td>2,17</td><td>2,58</td><td>3,39</td><td>3,9</td><td>4,8</td><td>5,9</td></tr>
<tr><td>5</td><td>3000</td><td>1,98</td><td>2,58</td><td>3,06</td><td>4,02</td><td>4,7</td><td>5,7</td><td>7,0</td></tr>
<tr><td>6</td><td>5000</td><td>2,46</td><td>3,19</td><td>3,79</td><td>5,00</td><td>5,8</td><td>7,1</td><td>8,6</td></tr>
<tr><td>7</td><td rowspan="4">450</td><td>2000</td><td>2,08</td><td>2,70</td><td>3,21</td><td>4,20</td><td>4,9</td><td>6,0</td><td>7,3</td></tr>
<tr><td>8</td><td>3000</td><td>2,47</td><td>3,20</td><td>3,80</td><td>5,00</td><td>5,8</td><td>7,1</td><td>8,6</td></tr>
<tr><td>9</td><td>5000</td><td>3,06</td><td>3,97</td><td>4,70</td><td>6,20</td><td>7,2</td><td>8,8</td><td>10,7</td></tr>
<tr><td>10</td><td>8000</td><td>3,72</td><td>4,80</td><td>2,74</td><td>7,60</td><td>8,8</td><td>10,8</td><td>13,0</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td></tr>
</table>



<table>
<colgroup><col width="59%"><col width="41%"></colgroup>
<tr><td rowspan="2">Сборка полос под сварку</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 60, лист 2</td></tr>
</table>


<a id="p103710"></a>Примечания:
1. <a id="p103711"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="24%"><col width="18%"><col width="18%"><col width="12%"><col width="15%"><col width="14%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="3">Материал</td><td colspan="2">Сборка полос</td></tr>
<tr><td>нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>с подгонкой</td><td>без подгонки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p103714"></a>Работа выполняется бригадой из двух человек:

                                  0,37    0,42    0,51
<a id="p103715"></a>                   Т = 0,00509 х В     х L     х h    .


<table>
<colgroup><col width="8%"><col width="11%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="7%"><col width="3%"><col width="4%"><col width="8%"><col width="8%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Сборка плоских фланцев из секторов</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 61, лист 1</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">1. Подать секторы к месту сборки. (рисунок</td></tr>
<tr><td colspan="13">2. Выставить сектора по разметке. не приводится)</td></tr>
<tr><td colspan="13">3. Подметить по месту, подрезать газом, зачистить шлифмашинкой.</td></tr>
<tr><td colspan="13">4. Собрать фланец из секторов в кольцо.</td></tr>
<tr><td colspan="13">5. Прихватить электросваркой.</td></tr>
<tr><td colspan="13">6. Снять фланец, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фланца</td><td>К-во секторов</td><td colspan="10">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">n, шт., до</td><td>5</td><td>10</td><td>18</td><td>26</td><td colspan="2">35</td><td>50</td><td>75</td><td>80</td><td>110</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">500</td><td>2</td><td>4,39</td><td>4,91</td><td>5,39</td><td>5,7</td><td colspan="2">6,0</td><td>7,0</td><td>8,2</td><td>8,8</td><td>9,6</td></tr>
<tr><td>2</td><td>3</td><td>6,07</td><td>6,79</td><td>7,46</td><td>7,9</td><td colspan="2">8,2</td><td>9,7</td><td>11,5</td><td>12,3</td><td>13,3</td></tr>
<tr><td>3</td><td>4</td><td>7,65</td><td>8,54</td><td>9,39</td><td>9,9</td><td colspan="2">10,5</td><td>12,3</td><td>14,4</td><td>15,5</td><td>16,8</td></tr>
<tr><td>4</td><td rowspan="5">1000</td><td>2</td><td>5,12</td><td>5,71</td><td>6,28</td><td>6,6</td><td colspan="2">6,9</td><td>7,8</td><td>9,1</td><td>9,8</td><td>10,7</td></tr>
<tr><td>5</td><td>3</td><td>5,47</td><td>7,90</td><td>8,68</td><td>9,2</td><td colspan="2">9,6</td><td>10,9</td><td>12,7</td><td>13,7</td><td>14,8</td></tr>
<tr><td>6</td><td>4</td><td>8,91</td><td>9,95</td><td>10,90</td><td>11,6</td><td colspan="2">12,2</td><td>13,7</td><td>16,0</td><td>17,2</td><td>18,6</td></tr>
<tr><td>7</td><td>5</td><td>10,60</td><td>11,9</td><td>13,1</td><td>13,9</td><td colspan="2">14,5</td><td>16,3</td><td>19,1</td><td>20,5</td><td>22,2</td></tr>
<tr><td>8</td><td>6</td><td>12,30</td><td>13,8</td><td>15,2</td><td>16,1</td><td colspan="2">16,9</td><td>18,9</td><td>22,2</td><td>23,8</td><td>25,8</td></tr>
<tr><td>9</td><td rowspan="5">1500</td><td>2</td><td>5,59</td><td>6,25</td><td>6,86</td><td>7,2</td><td colspan="2">7,6</td><td>8,3</td><td>9,7</td><td>10,5</td><td>11,4</td></tr>
<tr><td>10</td><td>3</td><td>7,73</td><td>8,64</td><td>9,49</td><td>10,1</td><td colspan="2">10,6</td><td>11,5</td><td>13,5</td><td>14,5</td><td>15,7</td></tr>
<tr><td>11</td><td>4</td><td>9,74</td><td>10,90</td><td>12,0</td><td>12,7</td><td colspan="2">13,3</td><td>14,5</td><td>17,0</td><td>18,3</td><td>19,8</td></tr>
<tr><td>12</td><td>5</td><td>11,70</td><td>13,00</td><td>14,3</td><td>15,2</td><td colspan="2">15,9</td><td>17,4</td><td>20,3</td><td>21,8</td><td>23,6</td></tr>
<tr><td>13</td><td>6</td><td>13,50</td><td>15,10</td><td>16,6</td><td>17,6</td><td colspan="2">18,4</td><td>20,1</td><td>23,6</td><td>25,3</td><td>27,4</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="11%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="7%"><col width="3%"><col width="4%"><col width="8%"><col width="8%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Сборка плоских фланцев из секторов</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 61, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фланца</td><td>К-во секторов</td><td colspan="10">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">n, шт., до</td><td>5</td><td>10</td><td>18</td><td>26</td><td colspan="2">35</td><td>50</td><td>75</td><td>80</td><td>110</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>14</td><td rowspan="5">2000</td><td>2</td><td>5,84</td><td>6,53</td><td>7,17</td><td>7,6</td><td colspan="2">7,9</td><td>9,0</td><td>10,6</td><td>11,4</td><td>12,3</td></tr>
<tr><td>15</td><td>3</td><td>8,08</td><td>9,03</td><td>9,92</td><td>10,5</td><td colspan="2">11,0</td><td>12,5</td><td>14,7</td><td>15,8</td><td>17,1</td></tr>
<tr><td>16</td><td>4</td><td>10,20</td><td>11,40</td><td>12,5</td><td>13,3</td><td colspan="2">13,9</td><td>15,8</td><td>18,5</td><td>19,8</td><td>21,5</td></tr>
<tr><td>17</td><td>5</td><td>12,20</td><td>13,60</td><td>14,9</td><td>15,8</td><td colspan="2">16,6</td><td>18,9</td><td>22,1</td><td>23,7</td><td>25,6</td></tr>
<tr><td>18</td><td>6</td><td>14,10</td><td>15,70</td><td>17,3</td><td>18,4</td><td colspan="2">19,2</td><td>21,8</td><td>25,6</td><td>27,4</td><td>29,7</td></tr>
<tr><td>19</td><td rowspan="5">2500</td><td>2</td><td>6,3</td><td>7,1</td><td>7,8</td><td>8,3</td><td colspan="2">8,7</td><td>9,9</td><td>11,6</td><td>12,5</td><td>13,5</td></tr>
<tr><td>20</td><td>3</td><td>8,8</td><td>9,8</td><td>10,8</td><td>11,5</td><td colspan="2">12,1</td><td>13,7</td><td>16,1</td><td>17,2</td><td>18,6</td></tr>
<tr><td>21</td><td>4</td><td>11,1</td><td>12,4</td><td>13,7</td><td>14,5</td><td colspan="2">15,2</td><td>17,2</td><td>20,2</td><td>21,7</td><td>23,5</td></tr>
<tr><td>22</td><td>5</td><td>13,3</td><td>14,9</td><td>16,3</td><td>17,3</td><td colspan="2">18,2</td><td>20,6</td><td>24,1</td><td>25,9</td><td>28,0</td></tr>
<tr><td>23</td><td>6</td><td>15,4</td><td>17,2</td><td>18,9</td><td>20,1</td><td colspan="2">21,0</td><td>23,9</td><td>28,0</td><td>30,0</td><td>32,4</td></tr>
<tr><td>24</td><td rowspan="7">3000</td><td>2</td><td>6,8</td><td>7,6</td><td>8,4</td><td>8,9</td><td colspan="2">9,3</td><td>10,7</td><td>12,5</td><td>13,4</td><td>14,5</td></tr>
<tr><td>25</td><td>3</td><td>9,5</td><td>10,6</td><td>11,7</td><td>12,4</td><td colspan="2">13,0</td><td>14,7</td><td>17,3</td><td>18,5</td><td>20,0</td></tr>
<tr><td>26</td><td>4</td><td>12,0</td><td>13,4</td><td>14,7</td><td>15,6</td><td colspan="2">16,3</td><td>18,6</td><td>21,7</td><td>23,3</td><td>25,2</td></tr>
<tr><td>27</td><td>5</td><td>14,3</td><td>16,0</td><td>17,6</td><td>18,6</td><td colspan="2">19,5</td><td>22,2</td><td>26,0</td><td>27,9</td><td>30,2</td></tr>
<tr><td>28</td><td>6</td><td>16,6</td><td>18,5</td><td>20,3</td><td>21,6</td><td colspan="2">22,6</td><td>25,7</td><td>30,0</td><td>32,3</td><td>34,9</td></tr>
<tr><td>29</td><td>7</td><td>18,7</td><td>20,9</td><td>23,0</td><td>24,4</td><td colspan="2">25,5</td><td>29,0</td><td>34,0</td><td>36,5</td><td>39,5</td></tr>
<tr><td>30</td><td>8</td><td>20,8</td><td>23,3</td><td>25,6</td><td>27,1</td><td colspan="2">28,4</td><td>32,3</td><td>37,8</td><td>40,6</td><td>43,9</td></tr>
<tr><td>31</td><td rowspan="7">4000</td><td>2</td><td>7,7</td><td>8,6</td><td>9,4</td><td>10,0</td><td colspan="2">10,5</td><td>12,0</td><td>14,0</td><td>15,0</td><td>16,3</td></tr>
<tr><td>32</td><td>3</td><td>10,7</td><td>11,9</td><td>13,1</td><td>13,9</td><td colspan="2">14,6</td><td>16,5</td><td>19,4</td><td>20,8</td><td>22,5</td></tr>
<tr><td>33</td><td>4</td><td>13,4</td><td>15,0</td><td>16,5</td><td>17,5</td><td colspan="2">18,3</td><td>20,8</td><td>24,4</td><td>26,2</td><td>28,3</td></tr>
<tr><td>34</td><td>5</td><td>16,1</td><td>17,9</td><td>19,7</td><td>20,9</td><td colspan="2">21,9</td><td>24,9</td><td>29,2</td><td>31,3</td><td>33,8</td></tr>
<tr><td>35</td><td>6</td><td>18,6</td><td>20,7</td><td>22,8</td><td>24,2</td><td colspan="2">25,3</td><td>28,8</td><td>33,7</td><td>36,2</td><td>39,2</td></tr>
<tr><td>36</td><td>7</td><td>21,0</td><td>23,5</td><td>25,8</td><td>27,3</td><td colspan="2">28,7</td><td>32,6</td><td>38,2</td><td>41,0</td><td>44,3</td></tr>
<tr><td>37</td><td>8</td><td>23,4</td><td>26,1</td><td>28,7</td><td>30,4</td><td colspan="2">31,9</td><td>36,2</td><td>42,4</td><td>45,6</td><td>49,3</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="11%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="7%"><col width="3%"><col width="4%"><col width="8%"><col width="8%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Сборка плоских фланцев из секторов</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 61, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фланца</td><td>К-во секторов</td><td colspan="10">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">n, шт., до</td><td>5</td><td>10</td><td>18</td><td>26</td><td colspan="2">35</td><td>50</td><td>75</td><td>90</td><td>110</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>38</td><td rowspan="7">5500</td><td>2</td><td>8,7</td><td>9,7</td><td>10,8</td><td>11,4</td><td colspan="2">12,0</td><td>13,6</td><td>15,9</td><td>17,1</td><td>18,5</td></tr>
<tr><td>39</td><td>3</td><td>12,1</td><td>13,5</td><td>14,9</td><td>15,8</td><td colspan="2">16,5</td><td>18,8</td><td>22,0</td><td>23,6</td><td>25,5</td></tr>
<tr><td>40</td><td>4</td><td>15,3</td><td>17,0</td><td>18,7</td><td>19,8</td><td colspan="2">20,8</td><td>23,7</td><td>27,7</td><td>30,0</td><td>32,2</td></tr>
<tr><td>41</td><td>5</td><td>18,2</td><td>20,4</td><td>22,4</td><td>23,7</td><td colspan="2">24,9</td><td>28,3</td><td>33,1</td><td>35,6</td><td>38,4</td></tr>
<tr><td>42</td><td>6</td><td>21,1</td><td>23,6</td><td>25,9</td><td>27,5</td><td colspan="2">28,8</td><td>32,7</td><td>38,3</td><td>41,1</td><td>44,5</td></tr>
<tr><td>43</td><td>7</td><td>23,9</td><td>26,7</td><td>29,3</td><td>31,0</td><td colspan="2">32,6</td><td>37,0</td><td>43,3</td><td>46,5</td><td>50,3</td></tr>
<tr><td>44</td><td>8</td><td>26,6</td><td>29,7</td><td>32,6</td><td>34,6</td><td colspan="2">36,2</td><td>41,2</td><td>48,2</td><td>51,8</td><td>56,0</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p103779"></a>Примечания:
1. <a id="p103780"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="18%"><col width="18%"><col width="18%"><col width="11%"><col width="11%"><col width="14%"><col width="12%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="2">Материал</td><td colspan="2">Длина стыка, мм</td><td colspan="2">Сборка фланцев</td></tr>
<tr><td>нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>до 200</td><td>св. 200</td><td>с подгонкой</td><td>без подгонки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>1,0</td><td>1,2</td><td>1,0</td><td>0,7</td></tr>
</table>


2. <a id="p103783"></a>Работа выполняется бригадой из двух человек:

                  0,22    0,8    0,16
<a id="p103784"></a>    Т = 0,4968 х Д     х n    х h       для h до 35 мм    поз. 1...13;

                  0,15    0,8    0,39
<a id="p103785"></a>    Т = 0,3477 х Д     х n    х h       для h 35 мм       поз. 1...13;

                 0,4    0,8    0,16
<a id="p103786"></a>    Т = 0,124 х Д    х n    х h         для h до 35 мм    поз. 14...44;

                 0,4    0,8    0,39
<a id="p103787"></a>    Т = 0,541 х Д    х n    х h         для h 35 мм       поз. 14...44.


<table>
<colgroup><col width="7%"><col width="7%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="15">Сборка продольных стыков обечаек под сварку Слесарно-сборочные работы</td></tr>
<tr><td colspan="15">Карта 62, лист 1</td></tr>
<tr><td colspan="15">Содержание работы</td></tr>
<tr><td colspan="15">1. Подать обечайку на сборочный стенд. (рисунок не</td></tr>
<tr><td colspan="15">2. Зачистить кромки под сварку. приводится)</td></tr>
<tr><td colspan="15">3. Подогнать продольный стык обечайки под сварку, выдержав зазор и уступность кромок.</td></tr>
<tr><td colspan="15">4. Установить, прихватить сборочные приспособления.</td></tr>
<tr><td colspan="15">5. Прихватить стык электросваркой.</td></tr>
<tr><td colspan="15">6. Снять и срубить сборочные приспособления, зачистить места прихваток.</td></tr>
<tr><td colspan="15">7. Снять обечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="3">Длина обечайки L, мм, до</td><td colspan="12">Толщина металла h, мм, до</td></tr>
<tr><td>обечайки Д,</td><td>2</td><td>3</td><td>4</td><td>7</td><td>12</td><td>16</td><td>24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td>мм, до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">500</td><td>300</td><td>1,27</td><td>1,57</td><td>2,06</td><td>2,47</td><td>3,28</td><td>3,82</td><td>4,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>500</td><td>1,67</td><td>2,07</td><td>2,72</td><td>3,25</td><td>4,32</td><td>5,03</td><td>6,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>700</td><td>2,01</td><td>2,49</td><td>3,26</td><td>3,90</td><td>5,18</td><td>6,04</td><td>7,4</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="7%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="15">Сборка продольных стыков обечаек под сварку Слесарно-сборочные работы</td></tr>
<tr><td colspan="15">Карта 62, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="3">Длина обечайки L, мм, до</td><td colspan="12">Толщина металла h, мм, до</td></tr>
<tr><td>обечайки Д,</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td>мм, до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>4</td><td rowspan="4">500</td><td>1000</td><td>2,43</td><td>3,01</td><td>3,95</td><td>4,72</td><td>6,29</td><td>7,32</td><td>9,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>1400</td><td>2,92</td><td>3,61</td><td>4,74</td><td>5,66</td><td>7,54</td><td>8,78</td><td>10,9</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>2000</td><td>3,54</td><td>4,38</td><td>5,75</td><td>6,86</td><td>9,14</td><td>10,7</td><td>13,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>2800</td><td>4,24</td><td>5,26</td><td>6,89</td><td>8,23</td><td>11,0</td><td>12,8</td><td>15,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td rowspan="6">750</td><td>500</td><td>1,98</td><td>2,45</td><td>3,21</td><td>3,83</td><td>5,10</td><td>5,94</td><td>7,3</td><td>9,0</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>700</td><td>2,37</td><td>2,94</td><td>3,85</td><td>4,60</td><td>6,12</td><td>7,13</td><td>8,8</td><td>10,8</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>1000</td><td>2,87</td><td>3,56</td><td>4,67</td><td>5,58</td><td>7,40</td><td>8,64</td><td>10,7</td><td>13,1</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td>1400</td><td>3,44</td><td>4,27</td><td>5,60</td><td>6,69</td><td>8,90</td><td>10,40</td><td>12,9</td><td>15,7</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>12</td><td>2000</td><td>4,17</td><td>5,18</td><td>6,78</td><td>8,11</td><td>10,8</td><td>12,6</td><td>15,6</td><td>19,0</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>2800</td><td>5,00</td><td>6,21</td><td>8,14</td><td>9,72</td><td>13,0</td><td>15,1</td><td>18,7</td><td>22,8</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td rowspan="5">1100</td><td>500</td><td>2,31</td><td>2,86</td><td>3,76</td><td>4,4</td><td>5,9</td><td>7,0</td><td>8,6</td><td>10,5</td><td>13,4</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>700</td><td>2,77</td><td>3,44</td><td>4,50</td><td>4,8</td><td>7,1</td><td>8,3</td><td>10,3</td><td>12,6</td><td>16,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>1000</td><td>3,36</td><td>4,16</td><td>5,46</td><td>6,5</td><td>8,6</td><td>10,1</td><td>12,6</td><td>15,3</td><td>19,5</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td>1400</td><td>4,03</td><td>5,00</td><td>6,55</td><td>6,9</td><td>10,4</td><td>12,1</td><td>15,0</td><td>18,4</td><td>23,3</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td>2000</td><td>4,83</td><td>6,05</td><td>7,94</td><td>9,4</td><td>12,6</td><td>14,7</td><td>18,2</td><td>22,3</td><td>28,3</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="7%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="15">Сборка продольных стыков обечаек под сварку Слесарно-сборочные работы</td></tr>
<tr><td colspan="15">Карта 62, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="3">Длина обечайки L, мм, до</td><td colspan="12">Толщина металла h, мм, до</td></tr>
<tr><td>обечайки Д,</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td>мм, до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>19</td><td rowspan="2">1100</td><td>2800</td><td>5,86</td><td>7,26</td><td>9,52</td><td>10,2</td><td>15,1</td><td>17,6</td><td>21,9</td><td>26,7</td><td>33,9</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>4000</td><td>7,10</td><td>8,80</td><td>11,5</td><td>12,3</td><td>18,4</td><td>21,4</td><td>26,5</td><td>32,4</td><td>41,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>21</td><td rowspan="7">1700</td><td>700</td><td>-</td><td>4,11</td><td>5,38</td><td>6,4</td><td>8,5</td><td>9,9</td><td>12,4</td><td>15,1</td><td>19,2</td><td>23,4</td><td>-</td><td>-</td></tr>
<tr><td>22</td><td>1000</td><td>-</td><td>4,98</td><td>6,53</td><td>7,8</td><td>10,4</td><td>12,1</td><td>15,0</td><td>18,3</td><td>23,3</td><td>28,4</td><td>-</td><td>-</td></tr>
<tr><td>23</td><td>1400</td><td>-</td><td>5,97</td><td>7,83</td><td>9,3</td><td>12,5</td><td>14,5</td><td>18,0</td><td>22,0</td><td>27,9</td><td>34,0</td><td>-</td><td>-</td></tr>
<tr><td>24</td><td>2000</td><td>-</td><td>7,24</td><td>9,49</td><td>11,4</td><td>15,1</td><td>17,6</td><td>21,8</td><td>26,6</td><td>33,8</td><td>41,2</td><td>-</td><td>-</td></tr>
<tr><td>25</td><td>2800</td><td>-</td><td>8,68</td><td>11,4</td><td>13,6</td><td>18,1</td><td>21,1</td><td>26,1</td><td>31,9</td><td>40,6</td><td>49,5</td><td>-</td><td>-</td></tr>
<tr><td>26</td><td>4000</td><td>-</td><td>10,5</td><td>13,8</td><td>16,5</td><td>21,9</td><td>25,6</td><td>31,8</td><td>38,7</td><td>49,2</td><td>60,0</td><td>-</td><td>-</td></tr>
<tr><td>27</td><td>5500</td><td>-</td><td>12,5</td><td>16,4</td><td>19,6</td><td>26,1</td><td>30,4</td><td>37,6</td><td>46,0</td><td>58,4</td><td>71,2</td><td>-</td><td>-</td></tr>
<tr><td>28</td><td rowspan="5">2600</td><td>700</td><td>-</td><td>-</td><td>6,41</td><td>7,6</td><td>10,2</td><td>11,9</td><td>14,7</td><td>18,0</td><td>22,8</td><td>27,9</td><td>34,5</td><td>-</td></tr>
<tr><td>29</td><td>1000</td><td>-</td><td>-</td><td>7,77</td><td>9,2</td><td>12,4</td><td>14,4</td><td>17,8</td><td>21,8</td><td>27,7</td><td>33,8</td><td>41,9</td><td>-</td></tr>
<tr><td>30</td><td>1400</td><td>-</td><td>-</td><td>9,32</td><td>11,1</td><td>14,8</td><td>17,3</td><td>21,4</td><td>26,1</td><td>33,2</td><td>40,5</td><td>50,2</td><td>-</td></tr>
<tr><td>31</td><td>2000</td><td>-</td><td>-</td><td>11,3</td><td>13,5</td><td>18,0</td><td>20,9</td><td>25,9</td><td>31,7</td><td>40,3</td><td>49,1</td><td>60,9</td><td>-</td></tr>
<tr><td>32</td><td>2800</td><td>-</td><td>-</td><td>13,6</td><td>16,2</td><td>21,5</td><td>25,1</td><td>31,1</td><td>38,0</td><td>48,3</td><td>58,9</td><td>73,0</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="7%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="15">Сборка продольных стыков обечаек под сварку Слесарно-сборочные работы</td></tr>
<tr><td colspan="15">Карта 62, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="3">Длина обечайки L, мм, до</td><td colspan="12">Толщина металла h, мм, до</td></tr>
<tr><td>обечайки Д,</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td>мм, до</td><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>33</td><td rowspan="3">2600</td><td>4000</td><td>-</td><td>-</td><td>16,4</td><td>19,6</td><td>26,1</td><td>30,4</td><td>37,7</td><td>46,1</td><td>58,5</td><td>71,4</td><td>88,5</td><td>-</td></tr>
<tr><td>34</td><td>5500</td><td>-</td><td>-</td><td>19,5</td><td>23,3</td><td>31,0</td><td>36,1</td><td>44,8</td><td>54,7</td><td>69,5</td><td>84,8</td><td>105,1</td><td>-</td></tr>
<tr><td>35</td><td>8000</td><td>-</td><td>-</td><td>23,9</td><td>28,5</td><td>38,0</td><td>44,2</td><td>54,8</td><td>67,0</td><td>85,1</td><td>103,8</td><td>128,6</td><td>-</td></tr>
<tr><td>36</td><td rowspan="7">4000</td><td>1000</td><td>-</td><td>-</td><td>-</td><td>11,1</td><td>14,8</td><td>17,0</td><td>21,3</td><td>26,0</td><td>33,0</td><td>40,3</td><td>49,9</td><td>58,2</td></tr>
<tr><td>37</td><td>1400</td><td>-</td><td>-</td><td>-</td><td>13,3</td><td>17,7</td><td>20,6</td><td>25,5</td><td>31,2</td><td>39,6</td><td>48,3</td><td>59,9</td><td>69,8</td></tr>
<tr><td>38</td><td>2000</td><td>-</td><td>-</td><td>-</td><td>16,1</td><td>21,4</td><td>25,0</td><td>31,0</td><td>37,8</td><td>48,0</td><td>58,6</td><td>72,6</td><td>84,6</td></tr>
<tr><td>39</td><td>2800</td><td>-</td><td>-</td><td>-</td><td>19,3</td><td>25,7</td><td>29,9</td><td>37,1</td><td>45,3</td><td>57,6</td><td>70,2</td><td>87,1</td><td>101,4</td></tr>
<tr><td>40</td><td>4000</td><td>-</td><td>-</td><td>-</td><td>23,4</td><td>31,2</td><td>36,3</td><td>45,0</td><td>55,0</td><td>69,8</td><td>85,2</td><td>105,6</td><td>123,0</td></tr>
<tr><td>41</td><td>5500</td><td>-</td><td>-</td><td>-</td><td>27,8</td><td>37,0</td><td>43,1</td><td>53,4</td><td>65,3</td><td>83,0</td><td>101,1</td><td>125,4</td><td>146,0</td></tr>
<tr><td>42</td><td>8000</td><td>-</td><td>-</td><td>-</td><td>34,0</td><td>45,3</td><td>52,8</td><td>65,4</td><td>79,9</td><td>101,5</td><td>123,8</td><td>153,5</td><td>178,8</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>


<a id="p103854"></a>Примечания:
1. <a id="p103855"></a>При измененных условиях приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="59%"><col width="41%"></colgroup>
<tr><td rowspan="2">Сборка продольных стыков обечаек под сварку</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 62, лист 5</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="11%"><col width="11%"><col width="11%"><col width="12%"><col width="11%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="6">Сборка обечаек</td></tr>
<tr><td>на изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>после строгания или машинной газовой резки</td><td>после ручной газовой резки</td><td>из двух полуобечаек</td><td>из трех полуобечаек</td><td>из четырех полуобечаек</td><td>из пяти полуобечаек</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,4</td><td>1,6</td><td>2,0</td><td>2,4</td><td>2,8</td></tr>
</table>


2. <a id="p103860"></a>Работа выполняется бригадой из двух человек:

                                  0,41    0,54    0,53
<a id="p103861"></a>                   Т = 0,00316 х Д     х L     х h    .


<table>
<colgroup><col width="12%"><col width="19%"><col width="15%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="5" rowspan="2">Сборка продольных стыков конических обечаек под сварку</td><td colspan="6">Слесарно-сборочные работы</td></tr>
<tr><td colspan="6">Карта 63, лист 1</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">1. Подать коническую обечайку на сборочный стенд. (рисунок не</td></tr>
<tr><td colspan="11">2. Зачистить кромки под сварку. приводится)</td></tr>
<tr><td colspan="11">3. Подогнать продольный стык обечайки, выдержав зазор и уступность кромок с помощью сборочных приспособлений.</td></tr>
<tr><td colspan="11">4. Установить, прихватить сборочные приспособления.</td></tr>
<tr><td colspan="11">5. Прихватить стык электросваркой.</td></tr>
<tr><td colspan="11">6. Снять и срубить сборочные приспособления, зачистить места прихваток.</td></tr>
<tr><td colspan="11">7. Снять обечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Больший диаметр</td><td>Длина обечайки</td><td colspan="8">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">обечайки Д, мм, до</td><td rowspan="2">L, мм, до</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>38</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="7">500</td><td>200</td><td>1,43</td><td>1,78</td><td>2,34</td><td>2,8</td><td>3,5</td><td>4,3</td><td>5,5</td><td>-</td></tr>
<tr><td>2</td><td>300</td><td>1,75</td><td>2,18</td><td>2,88</td><td>3,4</td><td>4,4</td><td>5,4</td><td>6,7</td><td>-</td></tr>
<tr><td>3</td><td>500</td><td>2,28</td><td>2,83</td><td>3,73</td><td>4,4</td><td>5,7</td><td>7,0</td><td>8,7</td><td>-</td></tr>
<tr><td>4</td><td>700</td><td>2,70</td><td>3,37</td><td>4,43</td><td>5,3</td><td>6,8</td><td>8,3</td><td>10,3</td><td>-</td></tr>
<tr><td>5</td><td>1000</td><td>3,24</td><td>4,04</td><td>5,30</td><td>6,4</td><td>8,1</td><td>10,0</td><td>12,4</td><td>-</td></tr>
<tr><td>6</td><td>1400</td><td>3,85</td><td>4,79</td><td>6,30</td><td>7,6</td><td>9,7</td><td>11,8</td><td>14,7</td><td>-</td></tr>
<tr><td>7</td><td>2000</td><td>4,62</td><td>5,8</td><td>7,60</td><td>9,1</td><td>11,6</td><td>14,2</td><td>14,7</td><td>-</td></tr>
<tr><td>8</td><td rowspan="4">750</td><td>500</td><td>2,68</td><td>3,33</td><td>4,39</td><td>5,3</td><td>6,7</td><td>8,2</td><td>10,3</td><td>13,1</td></tr>
<tr><td>9</td><td>700</td><td>3,18</td><td>3,96</td><td>5,20</td><td>6,3</td><td>8,0</td><td>9,8</td><td>12,2</td><td>15,6</td></tr>
<tr><td>10</td><td>1000</td><td>3,81</td><td>4,75</td><td>6,30</td><td>7,5</td><td>9,6</td><td>11,7</td><td>14,6</td><td>18,7</td></tr>
<tr><td>11</td><td>1400</td><td>4,53</td><td>5,60</td><td>7,40</td><td>8,9</td><td>11,4</td><td>13,9</td><td>17,3</td><td>22,2</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="19%"><col width="15%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="5" rowspan="2">Сборка продольных стыков конических обечаек под сварку</td><td colspan="6">Слесарно-сборочные работы</td></tr>
<tr><td colspan="6">Карта 63, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Больший диаметр</td><td>Длина обечайки</td><td colspan="8">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">обечайки Д, мм, до</td><td rowspan="2">L, мм, до</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>38</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>12</td><td rowspan="2">750</td><td>2000</td><td>5,4</td><td>6,8</td><td>8,9</td><td>10,7</td><td>13,6</td><td>16,7</td><td>20,8</td><td>27</td></tr>
<tr><td>13</td><td>2800</td><td>6,5</td><td>8,0</td><td>10,6</td><td>12,7</td><td>16,2</td><td>19,8</td><td>24,7</td><td>32</td></tr>
<tr><td>14</td><td rowspan="6">1100</td><td>500</td><td>3,1</td><td>3,8</td><td>5,1</td><td>6,1</td><td>7,8</td><td>9,6</td><td>11,9</td><td>15</td></tr>
<tr><td>15</td><td>700</td><td>3,7</td><td>4,6</td><td>6,1</td><td>7,3</td><td>9,3</td><td>11,4</td><td>14,2</td><td>18</td></tr>
<tr><td>16</td><td>1000</td><td>4,4</td><td>5,5</td><td>7,3</td><td>8,7</td><td>11,2</td><td>13,7</td><td>17,0</td><td>21</td></tr>
<tr><td>17</td><td>1400</td><td>5,3</td><td>6,6</td><td>8,7</td><td>10,4</td><td>13,3</td><td>16,2</td><td>20,2</td><td>26</td></tr>
<tr><td>18</td><td>2000</td><td>6,3</td><td>7,9</td><td>10,4</td><td>12,5</td><td>15,9</td><td>19,5</td><td>24,2</td><td>31</td></tr>
<tr><td>19</td><td>2800</td><td>7,5</td><td>9,4</td><td>12,3</td><td>14,8</td><td>18,9</td><td>23,1</td><td>29,0</td><td>37</td></tr>
<tr><td>20</td><td rowspan="6">1700</td><td>500</td><td>-</td><td>4,6</td><td>6,1</td><td>7,3</td><td>9,3</td><td>11,4</td><td>14,2</td><td>18</td></tr>
<tr><td>21</td><td>700</td><td>-</td><td>5,5</td><td>7,2</td><td>8,7</td><td>11,1</td><td>13,6</td><td>16,9</td><td>21</td></tr>
<tr><td>22</td><td>1000</td><td>-</td><td>6,6</td><td>8,7</td><td>10,4</td><td>13,3</td><td>16,3</td><td>20,2</td><td>26</td></tr>
<tr><td>23</td><td>1400</td><td>-</td><td>7,8</td><td>10,3</td><td>12,4</td><td>15,8</td><td>19,3</td><td>24,0</td><td>31</td></tr>
<tr><td>24</td><td>2000</td><td>-</td><td>9,4</td><td>12,4</td><td>14,8</td><td>18,9</td><td>23,2</td><td>29,0</td><td>37</td></tr>
<tr><td>25</td><td>2800</td><td>-</td><td>11,1</td><td>14,7</td><td>17,6</td><td>22,5</td><td>28,0</td><td>34,0</td><td>44</td></tr>
<tr><td>26</td><td rowspan="6">2600</td><td>500</td><td>-</td><td>-</td><td>7,2</td><td>8,7</td><td>11,1</td><td>13,5</td><td>16,9</td><td>21</td></tr>
<tr><td>27</td><td>700</td><td>-</td><td>-</td><td>8,6</td><td>10,3</td><td>13,1</td><td>16,1</td><td>20,0</td><td>26</td></tr>
<tr><td>28</td><td>1000</td><td>-</td><td>-</td><td>10,3</td><td>12,3</td><td>15,7</td><td>19,3</td><td>24,0</td><td>31</td></tr>
<tr><td>29</td><td>1400</td><td>-</td><td>-</td><td>12,2</td><td>14,6</td><td>18,7</td><td>22,9</td><td>29,0</td><td>37</td></tr>
<tr><td>30</td><td>2000</td><td>-</td><td>-</td><td>14,7</td><td>17,6</td><td>22,4</td><td>27,0</td><td>34,0</td><td>44</td></tr>
<tr><td>31</td><td>2800</td><td>-</td><td>-</td><td>17,4</td><td>20,9</td><td>27,0</td><td>33,0</td><td>41,0</td><td>52</td></tr>
<tr><td>32</td><td rowspan="5">4000</td><td>500</td><td>-</td><td>-</td><td>-</td><td>10,3</td><td>13,1</td><td>16,1</td><td>20,0</td><td>26</td></tr>
<tr><td>33</td><td>700</td><td>-</td><td>-</td><td>-</td><td>12,2</td><td>15,6</td><td>19,1</td><td>23,8</td><td>30</td></tr>
<tr><td>34</td><td>1000</td><td>-</td><td>-</td><td>-</td><td>14,7</td><td>18,7</td><td>22,9</td><td>29,0</td><td>37</td></tr>
<tr><td>35</td><td>1400</td><td>-</td><td>-</td><td>-</td><td>17,4</td><td>22,2</td><td>27,0</td><td>34,0</td><td>43</td></tr>
<tr><td>36</td><td>2000</td><td>-</td><td>-</td><td>-</td><td>20,9</td><td>27,0</td><td>33,0</td><td>41,0</td><td>52</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="19%"><col width="15%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="5" rowspan="2">Сборка продольных стыков конических обечаек под сварку</td><td colspan="6">Слесарно-сборочные работы</td></tr>
<tr><td colspan="6">Карта 63, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Больший диаметр</td><td>Длина обечайки</td><td colspan="8">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">обечайки Д, мм, до</td><td rowspan="2">L, мм, до</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>38</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>37</td><td rowspan="3">4000</td><td>2800</td><td>-</td><td>-</td><td>-</td><td>24,8</td><td>32</td><td>39</td><td>48</td><td>62</td></tr>
<tr><td>38</td><td>4000</td><td>-</td><td>-</td><td>-</td><td>30,5</td><td>38</td><td>46</td><td>58</td><td>74</td></tr>
<tr><td>39</td><td>5500</td><td>-</td><td>-</td><td>-</td><td>35,3</td><td>45</td><td>55</td><td>68</td><td>87</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p103921"></a>Примечания:
1. <a id="p103922"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="12%"><col width="11%"><col width="11%"><col width="11%"><col width="12%"><col width="11%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="6">Сборка обечаек</td></tr>
<tr><td>на изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>после строгания или машинной газовой резки</td><td>после ручной газовой резки</td><td>из двух полуобечаек</td><td>из трех полуобечаек</td><td>из четырех полуобечаек</td><td>из пяти полуобечаек</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,4</td><td>1,6</td><td>2,0</td><td>2,4</td><td>2,8</td></tr>
</table>


2. <a id="p103925"></a>Работа выполняется бригадой из двух человек:

                                     0,4    0,51    0,54
<a id="p103926"></a>                      Т = 0,00548 х Д    х L     х h    .


<table>
<colgroup><col width="11%"><col width="12%"><col width="16%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12">Сборка продольных стыков колец под сварку Слесарно-сборочные работы</td></tr>
<tr><td colspan="12">Карта 64, лист 1</td></tr>
<tr><td colspan="12">(рисунок не приводится)</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Подать свальцованное кольцо на сборочный стенд.</td></tr>
<tr><td colspan="12">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="12">3. Подогнать и собрать продольный стык.</td></tr>
<tr><td colspan="12">4. Подогнать кольца, выдержав зазор и уступность кромок.</td></tr>
<tr><td colspan="12">5. Установить, прихватить сборочные приспособления.</td></tr>
<tr><td colspan="12">6. Прихватить стык электросваркой.</td></tr>
<tr><td colspan="12">7. Срубить сборочные приспособления, зачистить места прихваток.</td></tr>
<tr><td colspan="12">8. Снять кольцо, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр кольца</td><td rowspan="3">Длина стыка L, мм, до</td><td colspan="9">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>35</td><td>55</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="2">100</td><td>50</td><td>0,57</td><td>0,71</td><td>0,94</td><td>1,12</td><td>1,43</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>100</td><td>0,68</td><td>0,84</td><td>1,11</td><td>1,34</td><td>1,71</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td rowspan="2">200</td><td>50</td><td>0,69</td><td>0,86</td><td>1,13</td><td>1,36</td><td>1,73</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>100</td><td>0,82</td><td>1,02</td><td>1,34</td><td>1,61</td><td>2,05</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td rowspan="3">400</td><td>50</td><td>0,83</td><td>1,03</td><td>1,36</td><td>1,63</td><td>2,09</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>100</td><td>0,98</td><td>1,22</td><td>1,61</td><td>1,93</td><td>2,47</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>150</td><td>1,08</td><td>1,35</td><td>1,77</td><td>2,13</td><td>2,72</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td rowspan="3">700</td><td>50</td><td>0,96</td><td>1,20</td><td>1,58</td><td>1,90</td><td>2,43</td><td>2,98</td><td>3,70</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>100</td><td>1,14</td><td>1,42</td><td>1,87</td><td>2,25</td><td>2,87</td><td>3,51</td><td>4,38</td><td>5,4</td><td>-</td></tr>
<tr><td>10</td><td>150</td><td>1,26</td><td>1,57</td><td>2,06</td><td>2,48</td><td>3,17</td><td>3,88</td><td>4,82</td><td>5,9</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="12%"><col width="16%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12">Сборка продольных стыков колец под сварку Слесарно-сборочные работы</td></tr>
<tr><td colspan="12">Карта 64, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр кольца</td><td rowspan="3">Длина стыка L, мм, до</td><td colspan="9">Толщина листа h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>35</td><td>55</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>11</td><td>700</td><td>300</td><td>1,49</td><td>1,85</td><td>2,44</td><td>2,93</td><td>3,74</td><td>4,5</td><td>5,7</td><td>6,9</td><td>-</td></tr>
<tr><td>12</td><td rowspan="3">1100</td><td>100</td><td>1,29</td><td>1,60</td><td>2,12</td><td>2,54</td><td>3,24</td><td>3,9</td><td>4,9</td><td>6,0</td><td>-</td></tr>
<tr><td>13</td><td>150</td><td>1,42</td><td>1,77</td><td>2,33</td><td>2,80</td><td>3,57</td><td>4,3</td><td>5,4</td><td>6,7</td><td>-</td></tr>
<tr><td>14</td><td>300</td><td>1,68</td><td>2,09</td><td>2,76</td><td>3,31</td><td>4,22</td><td>5,2</td><td>6,4</td><td>7,9</td><td>-</td></tr>
<tr><td>15</td><td rowspan="2">1700</td><td>150</td><td>-</td><td>1,99</td><td>2,62</td><td>3,15</td><td>4,02</td><td>4,9</td><td>6,1</td><td>7,5</td><td>9,6</td></tr>
<tr><td>16</td><td>300</td><td>-</td><td>2,35</td><td>3,10</td><td>3,72</td><td>4,75</td><td>5,8</td><td>7,2</td><td>8,8</td><td>11,3</td></tr>
<tr><td>17</td><td rowspan="2">2600</td><td>300</td><td>-</td><td>2,85</td><td>3,76</td><td>4,51</td><td>5,70</td><td>7,0</td><td>8,7</td><td>10,7</td><td>13,7</td></tr>
<tr><td>18</td><td>600</td><td>-</td><td>3,37</td><td>4,44</td><td>5,33</td><td>6,81</td><td>8,3</td><td>10,3</td><td>12,7</td><td>16,2</td></tr>
<tr><td>19</td><td rowspan="2">4000</td><td>300</td><td>-</td><td>3,34</td><td>4,41</td><td>5,38</td><td>6,74</td><td>8,3</td><td>10,3</td><td>12,6</td><td>16,1</td></tr>
<tr><td>20</td><td>600</td><td>-</td><td>3,95</td><td>5,20</td><td>6,27</td><td>7,96</td><td>9,7</td><td>12,1</td><td>14,9</td><td>19,0</td></tr>
<tr><td>21</td><td rowspan="4">5000</td><td>300</td><td>-</td><td>-</td><td>4,79</td><td>5,73</td><td>7,38</td><td>8,9</td><td>11,2</td><td>13,7</td><td>17,5</td></tr>
<tr><td>22</td><td>600</td><td>-</td><td>-</td><td>5,60</td><td>6,81</td><td>8,61</td><td>10,6</td><td>13,2</td><td>16,2</td><td>20,6</td></tr>
<tr><td>23</td><td>900</td><td>-</td><td>-</td><td>6,20</td><td>7,55</td><td>9,57</td><td>11,7</td><td>14,5</td><td>17,8</td><td>22,8</td></tr>
<tr><td>24</td><td>1200</td><td>-</td><td>-</td><td>6,70</td><td>8,00</td><td>10,2</td><td>12,5</td><td>15,6</td><td>19,1</td><td>24,4</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p103969"></a>Примечания:
1. <a id="p103970"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="14%"><col width="11%"><col width="11%"><col width="11%"><col width="12%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="6">Сборка колец</td></tr>
<tr><td>на изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>после строгания или машинной газовой резки</td><td>после ручной газовой резки</td><td>из двух полуколец</td><td>из трех полуколец</td><td>из четырех полуколец</td><td>из пяти полуколец</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,4</td><td>1,6</td><td>2,0</td><td>2,4</td><td>2,8</td></tr>
</table>



<a id="p103975"></a><a id="p103976"></a><a id="p103977"></a>

<table>
<colgroup><col width="65%"><col width="35%"></colgroup>
<tr><td rowspan="2">Сборка продольных стыков колец под сварку</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 64, лист 3</td></tr>
<tr><td>2. Работа выполняется бригадой из двух человек:</td><td></td></tr>
<tr><td>0,27 0,24 0,54 Т = 0,04447 х Д х L х h</td><td>поз. 1... 16;</td></tr>
<tr><td>0,37 0,24 0,54 Т = 0,02187 х Д х L х h</td><td>поз. 17... 24.</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="12%"><col width="11%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Сборка толстостенных обечаек из двух полуобечаек под электрошлаковую сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 65, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Подать полуобечайки к месту сборки. (рисунок не</td></tr>
<tr><td colspan="12">2. Зачистить продольные кромки полуобечаек под ползун. приводится)</td></tr>
<tr><td colspan="12">3. Уложить полуобечайки на сборочный стенд кромками вверх.</td></tr>
<tr><td colspan="12">4. Наложить на полуобечайку дистанционные пластины.</td></tr>
<tr><td colspan="12">5. Установить верхнюю полуобечайку на нижнюю, выверив совпадение продольных кромок.</td></tr>
<tr><td colspan="12">6. Собрать полуобечайки с помощью установки и прихватки скоб, наварышей и технологических планок.</td></tr>
<tr><td colspan="12">7. Выбить дистанционные пластины.</td></tr>
<tr><td colspan="12">8. Срубить скобы, наварыши, технологические планки, зачистить места прихваток.</td></tr>
<tr><td colspan="12">9. Снять обечайку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td>Толщина металла</td><td colspan="9">Длина обечайки L, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">h, мм, до</td><td>700</td><td>1000</td><td>1400</td><td colspan="2">2000</td><td>2800</td><td>4000</td><td>5500</td><td>8000</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="2">500</td><td>35</td><td>24,8</td><td>30,4</td><td>34,2</td><td colspan="2">45,1</td><td>54,6</td><td>67,0</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>55</td><td>31,9</td><td>39,1</td><td>44,1</td><td colspan="2">58,1</td><td>70,4</td><td>86,2</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td rowspan="2">750</td><td>35</td><td>28,6</td><td>35,0</td><td>39,5</td><td colspan="2">52,0</td><td>63,0</td><td>77,2</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>55</td><td>36,8</td><td>45,1</td><td>50,8</td><td colspan="2">67,0</td><td>81,1</td><td>99,4</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td rowspan="2">1100</td><td>35</td><td>32,7</td><td>40,0</td><td>45,1</td><td colspan="2">59,4</td><td>72,0</td><td>88,2</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>55</td><td>42,1</td><td>51,6</td><td>58,1</td><td colspan="2">76,6</td><td>92,7</td><td>113,6</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="12%"><col width="11%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Сборка толстостенных обечаек из двух полуобечаек под электрошлаковую сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 65, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td>Толщина металла</td><td colspan="9">Длина обечайки L, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td rowspan="2">h, мм, до</td><td>700</td><td>1000</td><td>1400</td><td colspan="2">2000</td><td>2800</td><td>4000</td><td>5500</td><td>8000</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>7</td><td>1100</td><td>80</td><td>51,9</td><td>63,6</td><td>71,7</td><td colspan="2">94,4</td><td>114,4</td><td>140,2</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td rowspan="5">1700</td><td>35</td><td>38,0</td><td>46,6</td><td>52,5</td><td colspan="2">69,2</td><td>83,9</td><td>102,8</td><td>123,2</td><td>152,5</td></tr>
<tr><td>9</td><td>55</td><td>49,0</td><td>60,1</td><td>67,7</td><td colspan="2">89,2</td><td>108,0</td><td>132,4</td><td>158,7</td><td>196,5</td></tr>
<tr><td>10</td><td>80</td><td>60,5</td><td>74,1</td><td>83,5</td><td colspan="2">110,0</td><td>133,2</td><td>163,3</td><td>195,7</td><td>242,4</td></tr>
<tr><td>11</td><td>120</td><td>75,9</td><td>93,0</td><td>104,7</td><td colspan="2">138,0</td><td>167,2</td><td>204,9</td><td>245,6</td><td>304,1</td></tr>
<tr><td>12</td><td>160</td><td>89,1</td><td>109,2</td><td>123,0</td><td colspan="2">162,1</td><td>196,4</td><td>240,6</td><td>288,5</td><td>357,2</td></tr>
<tr><td>13</td><td rowspan="5">2600</td><td>35</td><td>44,2</td><td>54,1</td><td>61,0</td><td colspan="2">80,3</td><td>97,3</td><td>119,2</td><td>143,0</td><td>177,0</td></tr>
<tr><td>14</td><td>55</td><td>56,9</td><td>69,7</td><td>78,5</td><td colspan="2">103,5</td><td>125,3</td><td>153,6</td><td>184,1</td><td>228,0</td></tr>
<tr><td>15</td><td>80</td><td>70,1</td><td>86,0</td><td>96,9</td><td colspan="2">127,6</td><td>154,6</td><td>189,4</td><td>227,1</td><td>281,2</td></tr>
<tr><td>16</td><td>120</td><td>88,0</td><td>107,9</td><td>121,5</td><td colspan="2">160,1</td><td>194,0</td><td>237,7</td><td>285,0</td><td>352,9</td></tr>
<tr><td>17</td><td>160</td><td>103,4</td><td>126,7</td><td>142,8</td><td colspan="2">188,1</td><td>227,9</td><td>279,3</td><td>334,8</td><td>414,6</td></tr>
<tr><td>18</td><td rowspan="5">4000</td><td>35</td><td>51,3</td><td>62,9</td><td>70,9</td><td colspan="2">93,4</td><td>113,1</td><td>138,6</td><td>166,2</td><td>205,8</td></tr>
<tr><td>19</td><td>55</td><td>66,1</td><td>81,0</td><td>91,3</td><td colspan="2">120,3</td><td>145,7</td><td>178,6</td><td>214,1</td><td>265,1</td></tr>
<tr><td>20</td><td>80</td><td>81,6</td><td>100,0</td><td>112,6</td><td colspan="2">148,4</td><td>179,7</td><td>220,3</td><td>264,1</td><td>327,0</td></tr>
<tr><td>21</td><td>120</td><td>102,3</td><td>125,4</td><td>141,3</td><td colspan="2">186,2</td><td>225,6</td><td>276,4</td><td>331,4</td><td>410,3</td></tr>
<tr><td>22</td><td>160</td><td>120,2</td><td>147,3</td><td>166,0</td><td colspan="2">218,7</td><td>265,0</td><td>324,7</td><td>389,3</td><td>482,0</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p104018"></a>Примечания:
1. <a id="p104019"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="34%"><col width="18%"><col width="18%"><col width="16%"><col width="15%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="2">Материал</td><td colspan="2">Сборка</td></tr>
<tr><td>времени</td><td>углеродистая сталь</td><td>легированная сталь</td><td>двух полуобечаек</td><td>обечайки</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,2</td><td>1,0</td><td>0,55</td></tr>
</table>


2. <a id="p104022"></a>Работа выполняется бригадой из двух человек:

                                  0,35    0,56    0,57
<a id="p104023"></a>                   Т = 0,00919 х Д     х h     х L    .


<table>
<colgroup><col width="11%"><col width="14%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Сборка обечаек по кольцевому стыку под сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 66, лист 1</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">1. Подать обечайки к месту сборки. (рисунок не</td></tr>
<tr><td colspan="13">2. Установить обечайки на роликовые опоры или кантователь. приводится)</td></tr>
<tr><td colspan="13">3. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="13">4. Подогнать стык, установить и прихватить сборочные приспособления.</td></tr>
<tr><td colspan="13">5. Прихватить стык электросваркой.</td></tr>
<tr><td colspan="13">6. Снять и срубить сборочные приспособления, зачистить места прихваток.</td></tr>
<tr><td colspan="13">7. Снять узел, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td colspan="11">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>6</td><td>7</td><td>12</td><td>16</td><td>24</td><td colspan="2">35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>250</td><td>5,3</td><td>5,8</td><td>6,8</td><td>7,7</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>300</td><td>6,2</td><td>6,9</td><td>7,9</td><td>8,9</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>400</td><td>7,8</td><td>8,7</td><td>10,1</td><td>11,4</td><td>13,0</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>500</td><td>9,5</td><td>10,6</td><td>12,2</td><td>13,8</td><td>15,7</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>600</td><td>11,1</td><td>12,4</td><td>14,3</td><td>16,1</td><td>18,4</td><td colspan="2">20,7</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>750</td><td>13,4</td><td>14,9</td><td>17,3</td><td>19,5</td><td>22,2</td><td colspan="2">25,0</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>900</td><td>15,7</td><td>17,5</td><td>20,2</td><td>22,7</td><td>25,9</td><td colspan="2">29,2</td><td>33,8</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="14%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="8" rowspan="2">Сборка обечаек по кольцевому стыку под сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 66, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обечайки</td><td colspan="11">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>6</td><td>7</td><td>12</td><td>16</td><td>24</td><td colspan="2">35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>8</td><td>1100</td><td>18,6</td><td>20,7</td><td>23,9</td><td>27,0</td><td>30,7</td><td colspan="2">34,7</td><td>40,1</td><td>45,1</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>1400</td><td>22,8</td><td>25,4</td><td>29,4</td><td>33,1</td><td>37,7</td><td colspan="2">42,6</td><td>49,2</td><td>55,4</td><td>63,1</td><td>-</td></tr>
<tr><td>10</td><td>1700</td><td>26,9</td><td>30,0</td><td>34,7</td><td>39,0</td><td>44,5</td><td colspan="2">50,2</td><td>58,0</td><td>65,3</td><td>74,5</td><td>81,7</td></tr>
<tr><td>11</td><td>2100</td><td>32,2</td><td>35,9</td><td>41,5</td><td>46,8</td><td>53,3</td><td colspan="2">60,1</td><td>69,4</td><td>78,2</td><td>89,1</td><td>97,7</td></tr>
<tr><td>12</td><td>2600</td><td>38,6</td><td>43,0</td><td>49,8</td><td>56,0</td><td>63,9</td><td colspan="2">72,0</td><td>83,3</td><td>93,8</td><td>106,9</td><td>117,2</td></tr>
<tr><td>13</td><td>3200</td><td>46,1</td><td>51,4</td><td>59,4</td><td>66,9</td><td>76,2</td><td colspan="2">85,9</td><td>99,4</td><td>111,9</td><td>127,5</td><td>139,8</td></tr>
<tr><td>14</td><td>4000</td><td>55,8</td><td>62,1</td><td>71,8</td><td>80,9</td><td>92,1</td><td colspan="2">103,9</td><td>120,1</td><td>135,3</td><td>154,2</td><td>169,0</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>


<a id="p104054"></a>Примечания:
1. <a id="p104055"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="9%"><col width="7%"><col width="7%"><col width="6%"><col width="7%"><col width="5%"><col width="7%"><col width="7%"><col width="9%"><col width="8%"><col width="6%"><col width="4%"><col width="5%"><col width="4%"><col width="5%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td><td colspan="2">Поворот обечаек</td><td colspan="5">Сборка обечаек</td><td colspan="4">Суммарная длина обечаек, м, до</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>механическим приводом</td><td>краном</td><td>цилиндрических</td><td>эллиптических</td><td>в горизонтальном положении</td><td>в вертикальном положении</td><td>под углом</td><td>6</td><td>10</td><td>15</td><td>св. 15</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,15</td><td>1,0</td><td>1,2</td><td>1,0</td><td>0,9</td><td>1,3</td><td>1,0</td><td>1,05</td><td>1,1</td><td>1,15</td></tr>
</table>


2. <a id="p104058"></a>Работа выполняется бригадой из двух человек:

                                      0,85    0,32
<a id="p104059"></a>                        Т = 0,0289 х Д     х h    .


<table>
<colgroup><col width="12%"><col width="15%"><col width="15%"><col width="7%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12">Сборка сферических днищ или крышек из Слесарно-сборочные работы лепестков</td></tr>
<tr><td colspan="12">Карта 67, лист 1</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Подать лепестки на сборочную плиту. (рисунок не</td></tr>
<tr><td colspan="12">2. Наметить припуски под обрезку. приводится)</td></tr>
<tr><td colspan="12">3. Зачистить кромки после газорезки.</td></tr>
<tr><td colspan="12">4. Выложить лепестки, установить зазоры и зафиксировать их планками или струбцинами.</td></tr>
<tr><td colspan="12">5. Прихватить лепестки электросваркой.</td></tr>
<tr><td colspan="12">6. Снять планки или струбцины.</td></tr>
<tr><td colspan="12">7. Зачистить места прихваток.</td></tr>
<tr><td colspan="12">8. Снять днище или крышку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Количество лепестков</td><td>Диаметр днища или</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">n, шт.</td><td rowspan="2">крышки Д, мм, до</td><td>4</td><td>8</td><td>12</td><td>20</td><td>32</td><td>44</td><td>60</td><td>100</td><td>160</td></tr>
<tr><td colspan="9">Время на днище или крышку Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="7">2</td><td>1000</td><td>32</td><td>43</td><td>51</td><td>64</td><td>78</td><td>90</td><td>103</td><td>128</td><td>156</td></tr>
<tr><td>2</td><td>1200</td><td>36</td><td>49</td><td>58</td><td>72</td><td>89</td><td>102</td><td>117</td><td>145</td><td>178</td></tr>
<tr><td>3</td><td>1500</td><td>43</td><td>57</td><td>68</td><td>85</td><td>104</td><td>119</td><td>138</td><td>170</td><td>208</td></tr>
<tr><td>4</td><td>1800</td><td>49</td><td>65</td><td>78</td><td>97</td><td>119</td><td>136</td><td>156</td><td>194</td><td>237</td></tr>
<tr><td>5</td><td>2200</td><td>56</td><td>75</td><td>89</td><td>112</td><td>137</td><td>157</td><td>180</td><td>223</td><td>273</td></tr>
<tr><td>6</td><td>2600</td><td>63</td><td>85</td><td>101</td><td>126</td><td>154</td><td>177</td><td>203</td><td>251</td><td>308</td></tr>
<tr><td>7</td><td>3000</td><td>70</td><td>94</td><td>112</td><td>139</td><td>170</td><td>196</td><td>225</td><td>278</td><td>341</td></tr>
<tr><td>8</td><td rowspan="5">3</td><td>1500</td><td>56</td><td>76</td><td>90</td><td>112</td><td>137</td><td>157</td><td>181</td><td>224</td><td>274</td></tr>
<tr><td>9</td><td>1800</td><td>64</td><td>86</td><td>102</td><td>127</td><td>156</td><td>179</td><td>206</td><td>255</td><td>312</td></tr>
<tr><td>10</td><td>2200</td><td>74</td><td>99</td><td>118</td><td>147</td><td>180</td><td>207</td><td>238</td><td>294</td><td>360</td></tr>
<tr><td>11</td><td>2600</td><td>83</td><td>112</td><td>133</td><td>166</td><td>203</td><td>233</td><td>268</td><td>331</td><td>405</td></tr>
<tr><td>12</td><td>3000</td><td>92</td><td>124</td><td>147</td><td>183</td><td>225</td><td>258</td><td>296</td><td>367</td><td>449</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="15%"><col width="15%"><col width="7%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12">Сборка сферических днищ или крышек из Слесарно-сборочные работы лепестков</td></tr>
<tr><td colspan="12">Карта 67, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Количество лепестков</td><td>Диаметр днища или</td><td colspan="9">Толщина металла h, мм, до</td></tr>
<tr><td rowspan="2">n, шт.</td><td rowspan="2">крышки Д, мм, до</td><td>4</td><td>8</td><td>12</td><td>20</td><td>32</td><td>44</td><td>60</td><td>100</td><td>160</td></tr>
<tr><td colspan="9">Время на днище или крышку Т, чел.-мин.</td></tr>
<tr><td>13</td><td rowspan="6">4</td><td>1800</td><td>78</td><td>105</td><td>125</td><td>155</td><td>190</td><td>218</td><td>251</td><td>310</td><td>379</td></tr>
<tr><td>14</td><td>2200</td><td>89</td><td>121</td><td>144</td><td>179</td><td>219</td><td>251</td><td>289</td><td>358</td><td>438</td></tr>
<tr><td>15</td><td>2600</td><td>101</td><td>136</td><td>162</td><td>202</td><td>247</td><td>283</td><td>325</td><td>403</td><td>493</td></tr>
<tr><td>16</td><td>3000</td><td>112</td><td>151</td><td>179</td><td>223</td><td>273</td><td>313</td><td>361</td><td>446</td><td>546</td></tr>
<tr><td>17</td><td>3500</td><td>125</td><td>168</td><td>200</td><td>249</td><td>305</td><td>350</td><td>402</td><td>498</td><td>609</td></tr>
<tr><td>18</td><td>4000</td><td>140</td><td>189</td><td>225</td><td>280</td><td>343</td><td>393</td><td>453</td><td>560</td><td>686</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p104095"></a>Примечания:
1. <a id="p104096"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="14%"><col width="18%"><col width="18%"><col width="11%"><col width="5%"><col width="5%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="3">Материал</td><td colspan="7">Количество лепестков</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>4</td><td>5</td><td>6</td><td>7</td><td>8</td><td>9</td><td>10</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,3</td><td>1,6</td><td>1,9</td><td>2,2</td><td>2,5</td><td>2,8</td></tr>
</table>


2. <a id="p104099"></a>Работа выполняется бригадой из двух человек:

                                  0,68    0,71    0,43
<a id="p104100"></a>                    Т = 0,0815 х n     х Д     х h    .


<table>
<colgroup><col width="11%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="7" rowspan="2">Сборка сферических днищ с корпусом</td><td colspan="7">Слесарно-сборочные работы</td></tr>
<tr><td colspan="7">Карта 68, лист 1</td></tr>
<tr><td colspan="14">Вид А Вид Б Вид В (рисунок не приводится) (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="14">Содержание работы</td></tr>
<tr><td colspan="14">1. Подать днище к месту сборки.</td></tr>
<tr><td colspan="14">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="14">3. Подогнать днище к корпусу, установить, прихватить сборочные приспособления.</td></tr>
<tr><td colspan="14">4. Прихватить днище с корпусом электросваркой.</td></tr>
<tr><td colspan="14">5. Срубить сборочные приспособления.</td></tr>
<tr><td colspan="14">6. Зачистить места прихваток.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр днища Д,</td><td colspan="12">Толщина корпуса h, мм, до</td></tr>
<tr><td rowspan="2">мм, до</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>250</td><td>4,6</td><td>5,2</td><td>6,1</td><td>6,8</td><td>8,1</td><td>8,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>300</td><td>5,4</td><td>6,1</td><td>7,2</td><td>8,0</td><td>9,4</td><td>10,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>400</td><td>7,0</td><td>7,9</td><td>9,2</td><td>10,3</td><td>12,1</td><td>13,2</td><td>15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>500</td><td>8,4</td><td>9,6</td><td>11,2</td><td>12,5</td><td>14,7</td><td>16,1</td><td>18</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>600</td><td>9,9</td><td>11,2</td><td>13,2</td><td>14,6</td><td>17,3</td><td>18,9</td><td>21</td><td>24</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>750</td><td>12,0</td><td>13,6</td><td>16,0</td><td>17,7</td><td>20,9</td><td>22,9</td><td>26</td><td>29</td><td>33</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>900</td><td>14,1</td><td>16,0</td><td>18,7</td><td>20,8</td><td>24,5</td><td>26,8</td><td>30</td><td>34</td><td>39</td><td>44</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>1100</td><td>16,8</td><td>19,0</td><td>22,3</td><td>24,7</td><td>29,2</td><td>32,0</td><td>36</td><td>41</td><td>47</td><td>53</td><td>60</td><td>65</td></tr>
<tr><td>9</td><td>1400</td><td>20,7</td><td>23,5</td><td>27,5</td><td>30,5</td><td>36,0</td><td>40,0</td><td>45</td><td>50</td><td>58</td><td>66</td><td>74</td><td>81</td></tr>
<tr><td>10</td><td>1700</td><td>-</td><td>27,8</td><td>32,6</td><td>36,0</td><td>43,0</td><td>47,0</td><td>53</td><td>59</td><td>68</td><td>77</td><td>87</td><td>95</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="12%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="7" rowspan="2">Сборка сферических днищ с корпусом</td><td colspan="7">Слесарно-сборочные работы</td></tr>
<tr><td colspan="7">Карта 68, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр днища Д,</td><td colspan="12">Толщина корпуса h, мм, до</td></tr>
<tr><td rowspan="2">мм, до</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td colspan="12">Время Т, чел.-мин.</td></tr>
<tr><td>11</td><td>2100</td><td>-</td><td>-</td><td>39,0</td><td>43,0</td><td>61,0</td><td>56,0</td><td>64</td><td>72</td><td>82</td><td>92</td><td>105</td><td>115</td></tr>
<tr><td>12</td><td>2600</td><td>-</td><td>-</td><td>47,0</td><td>52,0</td><td>62,0</td><td>68,0</td><td>77</td><td>86</td><td>99</td><td>111</td><td>126</td><td>138</td></tr>
<tr><td>13</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>63,0</td><td>74,0</td><td>81,0</td><td>92</td><td>103</td><td>119</td><td>133</td><td>151</td><td>165</td></tr>
<tr><td>14</td><td>4000</td><td>-</td><td>-</td><td>-</td><td>76,6</td><td>90,0</td><td>98,0</td><td>111</td><td>125</td><td>144</td><td>162</td><td>184</td><td>201</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>


<a id="p104131"></a>Примечания:
1. <a id="p104132"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="9%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="5%"><col width="6%"><col width="8%"><col width="9%"><col width="8%"><col width="7%"><col width="6%"><col width="7%"><col width="5%"><col width="6%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td><td colspan="2">Поворот обечаек</td><td colspan="2">Установка</td><td rowspan="2">Установка и прихватка пояска, установка днища на поясок (вид В)</td><td colspan="6">Сборка днищ</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>механическим приводом</td><td>краном</td><td>встык (вид А)</td><td>внутрь корпуса (вид Б)</td><td>с цилиндрическим корпусом</td><td>с эллиптическим корпусом</td><td>в горизонтальном положении</td><td>в вертикальном положении</td><td>с подгонкой</td><td>без подгонки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,15</td><td>1,0</td><td>1,25</td><td>1,35</td><td>1,0</td><td>1,2</td><td>1,0</td><td>0,9</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p104135"></a>Работа выполняется бригадой из двух человек:

                                      0,87    0,31
<a id="p104136"></a>                        Т = 0,0306 х Д     х h    .


<table>
<colgroup><col width="12%"><col width="14%"><col width="7%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="3%"><col width="7%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="9" rowspan="2">Сборка плоских днищ или решеток с корпусом</td><td colspan="6">Слесарно-сборочные работы</td></tr>
<tr><td colspan="6">Карта 69, лист 1</td></tr>
<tr><td colspan="15">Содержание работы</td></tr>
<tr><td colspan="15">1. Подать днище (решетку) к месту сборки. (рисунок не</td></tr>
<tr><td colspan="15">2. Зачистить кромки под сварку. приводится)</td></tr>
<tr><td colspan="15">3. Подогнать днище (решетку) к корпусу, установить и прихватить сборочные приспособления.</td></tr>
<tr><td colspan="15">4. Прихватить днище (решетку) к корпусу электросваркой.</td></tr>
<tr><td colspan="15">5. Срубить сборочные приспособления.</td></tr>
<tr><td colspan="15">6. Зачистить места прихваток.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр корпуса</td><td colspan="13">Толщина корпуса или решетки h, мм, до</td></tr>
<tr><td>или решетки</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td colspan="2">24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время на днище или решетку Т, чел.-мин.</td></tr>
<tr><td>1</td><td>250</td><td>3,5</td><td>3,9</td><td>4,6</td><td>5</td><td>6</td><td>7</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>300</td><td>4,0</td><td>4,6</td><td>5,4</td><td>6</td><td>7</td><td>9</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>400</td><td>5,2</td><td>5,9</td><td>6,9</td><td>7</td><td>9</td><td>10</td><td colspan="2">11</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>500</td><td>6,4</td><td>7,2</td><td>8,5</td><td>9</td><td>11</td><td>12</td><td colspan="2">13</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>600</td><td>7,5</td><td>8,5</td><td>9,9</td><td>11</td><td>13</td><td>14</td><td colspan="2">16</td><td>18</td><td>21</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>750</td><td>9,0</td><td>10,2</td><td>12</td><td>13</td><td>16</td><td>17</td><td colspan="2">20</td><td>22</td><td>25</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>900</td><td>11,0</td><td>12,4</td><td>14</td><td>16</td><td>19</td><td>20</td><td colspan="2">23</td><td>26</td><td>30</td><td>33</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>1100</td><td>13,3</td><td>14,6</td><td>17</td><td>17</td><td>22</td><td>24</td><td colspan="2">27</td><td>31</td><td>35</td><td>40</td><td>45</td><td>49</td></tr>
<tr><td>9</td><td>1400</td><td>16,1</td><td>18,3</td><td>21</td><td>23</td><td>27</td><td>30</td><td colspan="2">34</td><td>38</td><td>44</td><td>49</td><td>56</td><td>61</td></tr>
<tr><td>10</td><td>1700</td><td>-</td><td>21,1</td><td>25</td><td>27</td><td>32</td><td>35</td><td colspan="2">40</td><td>45</td><td>52</td><td>58</td><td>66</td><td>72</td></tr>
<tr><td>11</td><td>2100</td><td>-</td><td>-</td><td>30</td><td>33</td><td>39</td><td>42</td><td colspan="2">48</td><td>54</td><td>62</td><td>70</td><td>79</td><td>86</td></tr>
<tr><td>12</td><td>2600</td><td>-</td><td>-</td><td>36</td><td>39</td><td>47</td><td>51</td><td colspan="2">58</td><td>65</td><td>75</td><td>84</td><td>95</td><td>104</td></tr>
<tr><td>13</td><td>3200</td><td>-</td><td>-</td><td>-</td><td>47</td><td>56</td><td>61</td><td colspan="2">69</td><td>78</td><td>90</td><td>101</td><td>114</td><td>125</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="14%"><col width="7%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="3%"><col width="7%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="9" rowspan="2">Сборка плоских днищ или решеток с корпусом</td><td colspan="6">Слесарно-сборочные работы</td></tr>
<tr><td colspan="6">Карта 69, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр корпуса</td><td colspan="13">Толщина корпуса или решетки h, мм, до</td></tr>
<tr><td>или решетки</td><td>2</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td colspan="2">24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td>Д, мм, до</td><td colspan="13">Время на днище или решетку Т, чел.-мин.</td></tr>
<tr><td>14</td><td>4000</td><td>-</td><td>-</td><td>-</td><td>57</td><td>68</td><td>74</td><td colspan="2">84</td><td>95</td><td>109</td><td>122</td><td>139</td><td>152</td></tr>
<tr><td>15</td><td>4800</td><td>-</td><td>-</td><td>-</td><td>67</td><td>79</td><td>87</td><td colspan="2">99</td><td>111</td><td>127</td><td>143</td><td>162</td><td>178</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>


<a id="p104167"></a>Примечания:
1. <a id="p104168"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="12%"><col width="10%"><col width="10%"><col width="10%"><col width="8%"><col width="10%"><col width="12%"><col width="12%"><col width="9%"><col width="8%"></colgroup>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="2">Установка</td><td colspan="4">Сборка</td></tr>
<tr><td>на изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>встык</td><td>внутрь корпуса</td><td>с цилиндрическим корпусом</td><td>с эллиптическим корпусом</td><td>с подгонкой</td><td>без подгонки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,25</td><td>1,0</td><td>1,2</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p104171"></a>Работа выполняется бригадой из двух человек:

                                      0,87    0,31
<a id="p104172"></a>                        Т = 0,0231 х Д     х h    .


<table>
<colgroup><col width="5%"><col width="10%"><col width="10%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="3%"><col width="6%"><col width="6%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Сборка фланцев с обечайками</td><td colspan="6">Слесарно-сборочные работы</td></tr>
<tr><td colspan="6">Карта 70, лист 1</td></tr>
<tr><td colspan="15">Вид А Вид Б (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="15">Содержание работы</td></tr>
<tr><td colspan="15">1. Подать фланец на сборочную плиту.</td></tr>
<tr><td colspan="15">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="15">3. Подогнать обечайку по фланцу.</td></tr>
<tr><td colspan="15">4. Выверить положение фланца по обечайке и закрепить сборочными приспособлениями.</td></tr>
<tr><td colspan="15">5. Прихватить фланец к обечайке электросваркой.</td></tr>
<tr><td colspan="15">6. Срубить сборочные приспособления.</td></tr>
<tr><td colspan="15">7. Зачистить места прихваток.</td></tr>
<tr><td colspan="15">8. Снять узел, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Способ сборки</td><td rowspan="3">Диаметр обечайки Д, мм, до</td><td colspan="12">Толщина обечайки h, мм, до</td></tr>
<tr><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td colspan="2">24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td colspan="12">Время на фланец Т, чел.-мин.</td></tr>
<tr><td>1</td><td>Внахлестку</td><td>250</td><td>2,88</td><td>3,37</td><td>3,75</td><td>4,4</td><td>4,8</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td rowspan="7">(вид А)</td><td>300</td><td>3,38</td><td>3,96</td><td>4,39</td><td>5,2</td><td>5,6</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>400</td><td>4,34</td><td>5,08</td><td>5,64</td><td>6,6</td><td>7,2</td><td colspan="2">8,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>500</td><td>5,27</td><td>6,17</td><td>6,85</td><td>8,0</td><td>8,8</td><td colspan="2">10,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>600</td><td>6,17</td><td>7,23</td><td>8,02</td><td>9,4</td><td>10,4</td><td colspan="2">11,8</td><td>13,2</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>750</td><td>7,49</td><td>8,78</td><td>9,74</td><td>11,5</td><td>12,6</td><td colspan="2">14,3</td><td>16,1</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>900</td><td>8,78</td><td>10,3</td><td>11,4</td><td>13,5</td><td>14,8</td><td colspan="2">16,7</td><td>18,8</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>1100</td><td>10,5</td><td>12,3</td><td>13,6</td><td>16,1</td><td>17,6</td><td colspan="2">19,9</td><td>22,4</td><td>25,8</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="10%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="3%"><col width="6%"><col width="6%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Сборка фланцев с обечайками</td><td colspan="6">Слесарно-сборочные работы</td></tr>
<tr><td colspan="6">Карта 70, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Способ сборки</td><td rowspan="3">Диаметр обечайки Д, мм, до</td><td colspan="12">Толщина обечайки h, мм, до</td></tr>
<tr><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td colspan="2">24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td colspan="12">Время на фланец Т, чел.-мин.</td></tr>
<tr><td>9</td><td>Внахлестку</td><td>1400</td><td>12,9</td><td>15,1</td><td>16,8</td><td>19,8</td><td>21,7</td><td colspan="2">24,6</td><td>27,6</td><td>31,8</td><td>35,7</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td rowspan="5">(вид А)</td><td>1700</td><td>15,3</td><td>17,9</td><td>19,9</td><td>23,5</td><td>25,7</td><td colspan="2">29,1</td><td>32,7</td><td>37,7</td><td>42,2</td><td>47,9</td><td>52,4</td></tr>
<tr><td>11</td><td>2100</td><td>-</td><td>21,5</td><td>23,9</td><td>28,2</td><td>30,8</td><td colspan="2">35,0</td><td>39,3</td><td>45,2</td><td>50,8</td><td>57,6</td><td>62,9</td></tr>
<tr><td>12</td><td>2600</td><td>-</td><td>25,9</td><td>28,7</td><td>34,0</td><td>37,1</td><td colspan="2">42,1</td><td>47,3</td><td>54,4</td><td>61,1</td><td>69,3</td><td>75,8</td></tr>
<tr><td>13</td><td>3200</td><td>-</td><td>-</td><td>34,4</td><td>40,7</td><td>44,5</td><td colspan="2">50,4</td><td>56,7</td><td>65,2</td><td>73,2</td><td>83,1</td><td>90,8</td></tr>
<tr><td>14</td><td>4000</td><td>-</td><td>-</td><td>49,0</td><td>57,9</td><td>63,3</td><td colspan="2">71,8</td><td>80,7</td><td>92,8</td><td>104,2</td><td>119,0</td><td>129,2</td></tr>
<tr><td>15</td><td rowspan="14">Встык (вид Б)</td><td>250</td><td>3,00</td><td>3,5</td><td>3,9</td><td>4,6</td><td>5,0</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>300</td><td>3,52</td><td>4,1</td><td>4,5</td><td>5,4</td><td>5,9</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td>400</td><td>4,52</td><td>5,2</td><td>5,8</td><td>6,9</td><td>7,5</td><td colspan="2">8,6</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td>500</td><td>5,48</td><td>6,4</td><td>7,1</td><td>8,4</td><td>9,2</td><td colspan="2">10,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td>600</td><td>6,43</td><td>7,5</td><td>8,3</td><td>9,8</td><td>10,8</td><td colspan="2">12,3</td><td>13,8</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>750</td><td>7,80</td><td>9,1</td><td>10,2</td><td>12,0</td><td>13,1</td><td colspan="2">14,9</td><td>16,7</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>21</td><td>900</td><td>9,15</td><td>10,7</td><td>11,9</td><td>14,1</td><td>15,4</td><td colspan="2">17,4</td><td>19,6</td><td>22,5</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>22</td><td>1100</td><td>10,9</td><td>12,8</td><td>14,2</td><td>16,7</td><td>18,3</td><td colspan="2">20,8</td><td>23,3</td><td>26,8</td><td>30,1</td><td>-</td><td>-</td></tr>
<tr><td>23</td><td>1400</td><td>13,4</td><td>15,7</td><td>17,5</td><td>20,6</td><td>22,6</td><td colspan="2">25,6</td><td>28,8</td><td>33,1</td><td>37,2</td><td>42,1</td><td>-</td></tr>
<tr><td>24</td><td>1700</td><td>15,9</td><td>18,6</td><td>20,7</td><td>24,4</td><td>26,7</td><td colspan="2">30,3</td><td>34,1</td><td>39,2</td><td>44,0</td><td>49,9</td><td>54,6</td></tr>
<tr><td>25</td><td>2100</td><td>-</td><td>22,4</td><td>24,9</td><td>29,4</td><td>32,1</td><td colspan="2">36,4</td><td>40,9</td><td>47,1</td><td>52,9</td><td>60,0</td><td>65,6</td></tr>
<tr><td>26</td><td>2600</td><td>-</td><td>27,0</td><td>29,9</td><td>35,4</td><td>38,7</td><td colspan="2">43,9</td><td>49,3</td><td>56,7</td><td>63,7</td><td>72,2</td><td>79,0</td></tr>
<tr><td>27</td><td>3200</td><td>-</td><td>-</td><td>35,9</td><td>42,4</td><td>46,3</td><td colspan="2">52,5</td><td>59,0</td><td>67,9</td><td>76,3</td><td>86,5</td><td>94,6</td></tr>
<tr><td>28</td><td>4000</td><td>-</td><td>-</td><td>51,0</td><td>60,3</td><td>65,9</td><td colspan="2">74,8</td><td>84,0</td><td>96,7</td><td>108,6</td><td>123,1</td><td>134,6</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>


<a id="p104219"></a>Примечания:
1. <a id="p104220"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="17%"><col width="9%"><col width="10%"><col width="10%"><col width="13%"><col width="13%"><col width="12%"><col width="9%"><col width="8%"></colgroup>
<tr><td colspan="4" rowspan="2">Сборка фланцев с обечайками</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 70, лист 3</td></tr>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="5">Сборка</td></tr>
<tr><td>на изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>цилиндрической обечайки с одним фланцем</td><td>цилиндрической обечайки с двумя фланцами</td><td>эллиптической обечайки с одним фланцем</td><td>с подгонкой</td><td>без подгонки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,9</td><td>1,2</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p104225"></a>Работа выполняется бригадой из двух человек:

                               0,87    0,31
<a id="p104226"></a>                 Т = 0,0168 х Д     х h       поз. 1...14;

                               0,87    0,31
<a id="p104227"></a>                 Т = 0,0175 х Д     х h       поз. 15...25.


<table>
<colgroup><col width="5%"><col width="9%"><col width="10%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="14">Сборка фланцев со сферическими днищами Слесарно-сборочные работы</td></tr>
<tr><td colspan="14">Карта 71, лист 1</td></tr>
<tr><td colspan="14">Вид А Вид Б (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="14">Содержание работы</td></tr>
<tr><td colspan="14">1. Подать фланец и днище к месту сборки.</td></tr>
<tr><td colspan="14">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="14">3. Подогнать днище по фланцу, установить и прихватить сборочные приспособления.</td></tr>
<tr><td colspan="14">4. Прихватить фланец к днищу электросваркой.</td></tr>
<tr><td colspan="14">5. Срубить сборочные приспособления.</td></tr>
<tr><td colspan="14">6. Зачистить места прихваток.</td></tr>
<tr><td colspan="14">7. Снять узел, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид фланца</td><td>Диаметр днища</td><td colspan="11">Толщина днища h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="10">Вид А</td><td>250</td><td>3,17</td><td>3,72</td><td>4,1</td><td>4,8</td><td>5,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>300</td><td>3,72</td><td>4,35</td><td>4,8</td><td>5,7</td><td>6,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>400</td><td>4,77</td><td>5,59</td><td>6,2</td><td>7,3</td><td>8,0</td><td>9,10</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>500</td><td>4,12</td><td>6,79</td><td>7,5</td><td>8,9</td><td>9,7</td><td>11,1</td><td>12,4</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>600</td><td>6,79</td><td>7,96</td><td>8,8</td><td>10,4</td><td>11,4</td><td>13,0</td><td>14,6</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>750</td><td>8,25</td><td>9,66</td><td>10,7</td><td>12,7</td><td>13,9</td><td>15,7</td><td>17,7</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>900</td><td>9,67</td><td>11,3</td><td>12,6</td><td>14,9</td><td>16,2</td><td>18,4</td><td>20,7</td><td>23,8</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>1100</td><td>11,5</td><td>13,5</td><td>15,0</td><td>17,7</td><td>19,3</td><td>21,9</td><td>24,7</td><td>28,4</td><td>31,9</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>1400</td><td>14,2</td><td>16,6</td><td>18,5</td><td>21,8</td><td>23,9</td><td>27,1</td><td>30,4</td><td>35,0</td><td>39,3</td><td>44,6</td><td>-</td></tr>
<tr><td>10</td><td>1700</td><td>16,8</td><td>19,7</td><td>21,9</td><td>25,8</td><td>28,3</td><td>32,0</td><td>36,0</td><td>41,4</td><td>46,5</td><td>52,8</td><td>57,7</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="10%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="14">Сборка фланцев со сферическими днищами Слесарно-сборочные работы</td></tr>
<tr><td colspan="14">Карта 71, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид фланца</td><td>Диаметр днища</td><td colspan="11">Толщина днища h, мм, до</td></tr>
<tr><td rowspan="2">Д, мм, до</td><td>3</td><td>5</td><td>7</td><td>12</td><td>16</td><td>24</td><td>35</td><td>55</td><td>80</td><td>120</td><td>160</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>11</td><td rowspan="4">Вид А</td><td>2100</td><td>-</td><td>23,7</td><td>26,3</td><td>31,0</td><td>34,0</td><td>38,5</td><td>43,3</td><td>49,8</td><td>55,9</td><td>63,4</td><td>69,3</td></tr>
<tr><td>12</td><td>2600</td><td>-</td><td>28,5</td><td>31,6</td><td>37,4</td><td>40,9</td><td>46,4</td><td>52,1</td><td>59,9</td><td>67,3</td><td>76,3</td><td>83,5</td></tr>
<tr><td>13</td><td>3200</td><td>-</td><td>-</td><td>37,9</td><td>44,8</td><td>49,0</td><td>55,5</td><td>62,4</td><td>71,8</td><td>80,7</td><td>91,5</td><td>100,0</td></tr>
<tr><td>14</td><td>4000</td><td>-</td><td>-</td><td>53,9</td><td>63,7</td><td>69,7</td><td>79,0</td><td>88,8</td><td>102,2</td><td>114,8</td><td>130,1</td><td>142,3</td></tr>
<tr><td>15</td><td rowspan="14">Вид Б</td><td>250</td><td>2,95</td><td>3,46</td><td>3,84</td><td>4,53</td><td>4,96</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>300</td><td>3,46</td><td>4,04</td><td>4,49</td><td>5,31</td><td>5,81</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>17</td><td>400</td><td>4,44</td><td>5,20</td><td>5,77</td><td>6,82</td><td>7,46</td><td>8,46</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td>500</td><td>5,39</td><td>6,31</td><td>7,00</td><td>8,28</td><td>9,06</td><td>10,3</td><td>11,6</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td>600</td><td>6,32</td><td>7,40</td><td>8,21</td><td>9,71</td><td>10,6</td><td>12,0</td><td>13,5</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>750</td><td>7,67</td><td>8,99</td><td>9,97</td><td>11,8</td><td>12,9</td><td>14,6</td><td>16,4</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>21</td><td>900</td><td>8,99</td><td>10,5</td><td>11,7</td><td>13,8</td><td>15,1</td><td>17,1</td><td>19,3</td><td>22,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>22</td><td>1100</td><td>10,7</td><td>12,5</td><td>13,9</td><td>16,4</td><td>18,0</td><td>20,4</td><td>22,9</td><td>26,4</td><td>29,6</td><td>-</td><td>-</td></tr>
<tr><td>23</td><td>1400</td><td>13,2</td><td>15,5</td><td>17,2</td><td>20,3</td><td>22,2</td><td>25,2</td><td>28,3</td><td>32,5</td><td>36,5</td><td>41,4</td><td>-</td></tr>
<tr><td>24</td><td>1700</td><td>15,6</td><td>18,3</td><td>20,3</td><td>24,0</td><td>26,3</td><td>29,8</td><td>33,5</td><td>38,5</td><td>43,3</td><td>49,0</td><td>53,6</td></tr>
<tr><td>25</td><td>2100</td><td>-</td><td>22,0</td><td>24,4</td><td>28,9</td><td>31,6</td><td>35,8</td><td>40,2</td><td>46,3</td><td>52,0</td><td>58,9</td><td>64,4</td></tr>
<tr><td>26</td><td>2600</td><td>-</td><td>26,5</td><td>29,4</td><td>34,8</td><td>38,0</td><td>43,1</td><td>48,4</td><td>55,7</td><td>62,6</td><td>71,0</td><td>77,6</td></tr>
<tr><td>27</td><td>3200</td><td>-</td><td>-</td><td>35,2</td><td>41,6</td><td>45,5</td><td>51,6</td><td>58,0</td><td>66,8</td><td>75,0</td><td>85,0</td><td>93,0</td></tr>
<tr><td>28</td><td>4000</td><td>-</td><td>-</td><td>50,1</td><td>59,3</td><td>64,8</td><td>73,5</td><td>82,6</td><td>95,0</td><td>106,7</td><td>121,0</td><td>132,3</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>


<a id="p104273"></a>Примечания:
1. <a id="p104274"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="17%"><col width="10%"><col width="10%"><col width="10%"><col width="17%"><col width="18%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="4" rowspan="2">Сборка фланцев со сферическими днищами</td><td colspan="4">Слесарно-сборочные работы</td></tr>
<tr><td colspan="4">Карта 71, лист 3</td></tr>
<tr><td>Факторы, влияющие</td><td colspan="3">Материал</td><td colspan="4">Сборка</td></tr>
<tr><td>на изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>со сферическими днищами</td><td>с эллиптическими днищами</td><td>с подгонкой</td><td>без подгонки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,2</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p104279"></a>Работа выполняется бригадой из двух человек:

                               0,87    0,31
<a id="p104280"></a>                 Т = 0,0185 х Д     х h       поз. 1...14;

                               0,87    0,31
<a id="p104281"></a>                 Т = 0,0172 х Д     х h       поз. 15...28.


<table>
<colgroup><col width="6%"><col width="11%"><col width="15%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="6%"></colgroup>
<tr><td colspan="7" rowspan="2">Сборка фланцев с трубами или патрубками</td><td colspan="6">Слесарно-сборочные работы</td></tr>
<tr><td colspan="6">Карта 72, лист 1</td></tr>
<tr><td colspan="13">Вид А Вид Б (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="13">Вид В Вид Г (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">1. Подать фланец и трубу (патрубок) к месту сборки.</td></tr>
<tr><td colspan="13">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="13">3. Подогнать между собой фланец и трубу (патрубок).</td></tr>
<tr><td colspan="13">4. Выверить положение фланца на электросваркой трубе (патрубке) и прихватить.</td></tr>
<tr><td colspan="13">5. Зачистить места прихваток.</td></tr>
<tr><td colspan="13">6. Снять узел, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид сборки</td><td>Длина трубы</td><td colspan="10">Диаметр трубы Д, мм, до</td></tr>
<tr><td>или патрубка</td><td>25</td><td>42</td><td>60</td><td colspan="2">102</td><td>159</td><td>203</td><td>245</td><td>325</td><td>377</td></tr>
<tr><td>L, мм, до</td><td colspan="10">Время на узел Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="8">Вид А</td><td>100</td><td>0,91</td><td>1,17</td><td>1,39</td><td colspan="2">1,79</td><td>2,2</td><td>2,6</td><td>3,0</td><td>3,8</td><td>4,3</td></tr>
<tr><td>2</td><td>300</td><td>1,03</td><td>1,32</td><td>1,57</td><td colspan="2">2,00</td><td>2,5</td><td>2,9</td><td>3,4</td><td>4,3</td><td>4,8</td></tr>
<tr><td>3</td><td>500</td><td>1,09</td><td>1,4</td><td>1,66</td><td colspan="2">2,10</td><td>2,6</td><td>3,1</td><td>3,6</td><td>4,5</td><td>5,1</td></tr>
<tr><td>4</td><td>1000</td><td>1,18</td><td>1,51</td><td>1,79</td><td colspan="2">2,30</td><td>2,8</td><td>3,4</td><td>3,9</td><td>4,9</td><td>5,5</td></tr>
<tr><td>5</td><td>2000</td><td>1,27</td><td>1,63</td><td>1,94</td><td colspan="2">2,50</td><td>3,0</td><td>3,7</td><td>4,3</td><td>5,4</td><td>6,0</td></tr>
<tr><td>6</td><td>4000</td><td>1,37</td><td>1,76</td><td>2,00</td><td colspan="2">2,70</td><td>3,3</td><td>3,9</td><td>4,6</td><td>5,7</td><td>6,4</td></tr>
<tr><td>7</td><td>6000</td><td>1,43</td><td>1,84</td><td>2,20</td><td colspan="2">2,80</td><td>3,5</td><td>4,1</td><td>4,8</td><td>6,0</td><td>6,7</td></tr>
<tr><td>8</td><td>10000</td><td>1,51</td><td>1,94</td><td>2,30</td><td colspan="2">2,90</td><td>3,7</td><td>4,4</td><td>5,1</td><td>6,4</td><td>7,1</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="11%"><col width="15%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="6%"></colgroup>
<tr><td colspan="7" rowspan="2">Сборка фланцев с трубами или патрубками</td><td colspan="6">Слесарно-сборочные работы</td></tr>
<tr><td colspan="6">Карта 72, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид сборки</td><td>Длина трубы</td><td colspan="10">Диаметр трубы Д, мм, до</td></tr>
<tr><td>или патрубка</td><td>25</td><td>42</td><td>60</td><td colspan="2">102</td><td>159</td><td>203</td><td>245</td><td>325</td><td>377</td></tr>
<tr><td>L, мм, до</td><td colspan="10">Время на узел Т, чел.-мин.</td></tr>
<tr><td>9</td><td rowspan="7">Вид Б</td><td>300</td><td>0,88</td><td>1,13</td><td>1,34</td><td colspan="2">1,73</td><td>2,1</td><td>2,5</td><td>2,9</td><td>3,6</td><td>4,0</td></tr>
<tr><td>10</td><td>500</td><td>0,93</td><td>1,19</td><td>1,42</td><td colspan="2">1,83</td><td>2,3</td><td>2,6</td><td>3,0</td><td>3,8</td><td>4,3</td></tr>
<tr><td>11</td><td>1000</td><td>1,00</td><td>1,29</td><td>1,53</td><td colspan="2">1,97</td><td>2,4</td><td>2,8</td><td>3,3</td><td>4,0</td><td>4,6</td></tr>
<tr><td>12</td><td>2000</td><td>1,08</td><td>1,39</td><td>1,65</td><td colspan="2">2,10</td><td>2,6</td><td>3,0</td><td>3,6</td><td>4,4</td><td>5,0</td></tr>
<tr><td>13</td><td>4000</td><td>1,17</td><td>1,50</td><td>1,78</td><td colspan="2">2,30</td><td>2,8</td><td>3,4</td><td>3,9</td><td>4,8</td><td>5,4</td></tr>
<tr><td>14</td><td>6000</td><td>1,22</td><td>1,60</td><td>1,9</td><td colspan="2">2,40</td><td>2,9</td><td>3,5</td><td>4,0</td><td>5,0</td><td>5,7</td></tr>
<tr><td>15</td><td>10000</td><td>1,29</td><td>1,66</td><td>1,97</td><td colspan="2">2,50</td><td>3,1</td><td>3,7</td><td>4,3</td><td>5,4</td><td>6,0</td></tr>
<tr><td>16</td><td>Вид В и вид</td><td>500</td><td>1,50</td><td>1,76</td><td>1,79</td><td colspan="2">2,31</td><td>2,8</td><td>3,5</td><td>4,2</td><td>5,5</td><td>6,4</td></tr>
<tr><td>17</td><td rowspan="5">Г</td><td>1000</td><td>1,27</td><td>1,62</td><td>1,93</td><td colspan="2">2,5</td><td>3,0</td><td>3,6</td><td>4,4</td><td>5,8</td><td>6,7</td></tr>
<tr><td>18</td><td>2000</td><td>1,37</td><td>1,76</td><td>2,10</td><td colspan="2">2,7</td><td>3,3</td><td>4,0</td><td>4,9</td><td>6,5</td><td>7,4</td></tr>
<tr><td>19</td><td>4000</td><td>1,48</td><td>1,90</td><td>2,30</td><td colspan="2">2,9</td><td>3,6</td><td>4,3</td><td>5,1</td><td>6,8</td><td>7,8</td></tr>
<tr><td>20</td><td>6000</td><td>1,54</td><td>1,98</td><td>2,40</td><td colspan="2">3,0</td><td>3,7</td><td>4,4</td><td>5,4</td><td>7,2</td><td>8,2</td></tr>
<tr><td>21</td><td>10000</td><td>1,63</td><td>2,00</td><td>2,50</td><td colspan="2">3,2</td><td>3,9</td><td>4,9</td><td>5,9</td><td>7,8</td><td>8,9</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p104319"></a>Примечания:
1. <a id="p104320"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="34%"><col width="34%"><col width="32%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="2">Сборка</td></tr>
<tr><td>времени</td><td>одного фланца с одной трубой или патрубком</td><td>двух фланцев с одной трубой или патрубком</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,9</td></tr>
</table>


2. <a id="p104323"></a>Работа выполняется бригадой из двух человек:

                 0,11    0,48
<a id="p104324"></a>    Т = 0,118 х L     х Д            для Д <= 159 мм        поз. 1...8.


<a id="p104327"></a><a id="p104328"></a><a id="p104329"></a><a id="p104330"></a><a id="p104331"></a>

<table>
<colgroup><col width="60%"><col width="40%"></colgroup>
<tr><td rowspan="2">Сборка фланцев с трубами или патрубками</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 72, лист 3</td></tr>
<tr><td>0,11 0,78 Т = 0,0256 х L х Д для Д &gt; 159 мм</td><td>поз. 1...8;</td></tr>
<tr><td>0,11 0,48 Т = 0,1008 х L х Д для Д &lt;= 159 мм</td><td>поз. 9...15;</td></tr>
<tr><td>0,11 0,78 Т = 0,0214 х L х Д для Д &gt; 159 мм</td><td>поз. 9...15;</td></tr>
<tr><td>0,11 0,48 Т = 0,127 х L х Д для Д &lt;= 159 мм</td><td>поз. 16...21;</td></tr>
<tr><td>0,11 1,0 Т = 0,00882 х L х Д для Д &gt; 159 мм</td><td>поз. 16...21.</td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="31%"><col width="11%"><col width="11%"><col width="12%"><col width="12%"><col width="12%"></colgroup>
<tr><td colspan="7">Сборка труб под сварку Слесарно-сборочные работы</td></tr>
<tr><td colspan="7">Карта 73, лист 1</td></tr>
<tr><td colspan="7">(рисунок не приводится)</td></tr>
<tr><td colspan="7">Содержание работы</td></tr>
<tr><td colspan="7">1. Подать трубу к месту сборки.</td></tr>
<tr><td colspan="7">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="7">3. Установить трубы под сварку и подогнать стык.</td></tr>
<tr><td colspan="7">4. Прихватить стык электросваркой.</td></tr>
<tr><td colspan="7">5. Зачистить места прихваток.</td></tr>
<tr><td colspan="7">6. Снять узел, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Наружный диаметр трубы Д, мм, до</td><td colspan="5">Толщина стенки трубы h, мм, до</td></tr>
<tr><td>2</td><td>4</td><td>8</td><td>12</td><td>16</td></tr>
<tr><td colspan="5">Время на один стык Т, чел.-мин.</td></tr>
<tr><td>1</td><td>25</td><td>1,2</td><td>1,5</td><td>1,8</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>50</td><td>1,7</td><td>2,1</td><td>2,7</td><td>3,1</td><td>-</td></tr>
<tr><td>3</td><td>83</td><td>-</td><td>2,8</td><td>3,6</td><td>4,1</td><td>4,5</td></tr>
<tr><td>4</td><td>133</td><td>-</td><td>3,7</td><td>4,6</td><td>5,3</td><td>5,8</td></tr>
<tr><td>5</td><td>203</td><td>-</td><td>-</td><td>5,7</td><td>6,7</td><td>7,3</td></tr>
<tr><td>6</td><td>245</td><td>-</td><td>-</td><td>6,5</td><td>7,4</td><td>8,1</td></tr>
<tr><td>7</td><td>325</td><td>-</td><td>-</td><td>7,5</td><td>8,6</td><td>9,5</td></tr>
<tr><td>8</td><td>377</td><td>-</td><td>-</td><td>8,2</td><td>9,4</td><td>10,3</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td></tr>
</table>


<a id="p104352"></a>Примечания:
1. <a id="p104353"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="13%"><col width="9%"><col width="9%"><col width="9%"><col width="11%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"></colgroup>
<tr><td colspan="13">Сборка труб под сварку Слесарно-сборочные работы</td></tr>
<tr><td colspan="13">Карта 73, лист 2</td></tr>
<tr><td>Факторы, влияющие на изменение</td><td colspan="3">Материал</td><td rowspan="2">На каждый последующий стык</td><td colspan="4">Суммарная длина труб, м, до</td><td colspan="4">Сборка труб</td></tr>
<tr><td>нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>6</td><td>10</td><td>11 - 15</td><td>св. 15</td><td>встык</td><td>под углом</td><td>с подгонкой</td><td>без подгонки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>0,8</td><td>1,0</td><td>1,05</td><td>1,1</td><td>1,15</td><td>1,0</td><td>1,3</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p104357"></a>Работа выполняется бригадой из двух человек:

                                     0,55    0,33
<a id="p104358"></a>                        Т = 0,158 х Д     х h    .


<table>
<colgroup><col width="12%"><col width="14%"><col width="17%"><col width="11%"><col width="6%"><col width="3%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="5" rowspan="2">Сборка змеевиков под сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 74, лист 1</td></tr>
<tr><td colspan="10">Вид А Вид Б Вид В</td></tr>
<tr><td colspan="10">(рисунок (рисунок (рисунок не приводится) не приводится) не приводится)</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Подать трубу змеевика к месту сборки.</td></tr>
<tr><td colspan="10">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="10">3. Подогнать и собрать стык змеевика.</td></tr>
<tr><td colspan="10">4. Прихватить стык электросваркой.</td></tr>
<tr><td colspan="10">5. Зачистить места прихваток.</td></tr>
<tr><td colspan="10">6. Снять узел, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид змеевика</td><td>Габариты змеевика</td><td colspan="7">Диаметр трубы d, мм, до</td></tr>
<tr><td rowspan="2">Д или L, мм, до</td><td>25</td><td colspan="2">33</td><td>45</td><td>57</td><td>76</td><td>89</td></tr>
<tr><td colspan="7">Время на один стык змеевика Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="6">Круглый цилиндрический (вид А)</td><td>500</td><td>2,2</td><td colspan="2">2,6</td><td>3,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>1000</td><td>3,3</td><td colspan="2">3,9</td><td>4,7</td><td>5,4</td><td>6,4</td><td>-</td></tr>
<tr><td>3</td><td>1500</td><td>3,3</td><td colspan="2">3,9</td><td>4,7</td><td>5,4</td><td>6,4</td><td>7,0</td></tr>
<tr><td>4</td><td>2000</td><td>3,7</td><td colspan="2">4,4</td><td>5,2</td><td>6,0</td><td>7,2</td><td>7,9</td></tr>
<tr><td>5</td><td>3000</td><td>-</td><td colspan="2">5,0</td><td>6,1</td><td>7,0</td><td>8,3</td><td>9,1</td></tr>
<tr><td>6</td><td>4000</td><td>-</td><td colspan="2">-</td><td>6,8</td><td>7,8</td><td>9,2</td><td>10,1</td></tr>
<tr><td>7</td><td rowspan="3">Плоский (вид Б)</td><td>1000</td><td>2,0</td><td colspan="2">2,4</td><td>2,9</td><td>3,3</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>2000</td><td>2,4</td><td colspan="2">2,8</td><td>3,4</td><td>3,9</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>3000</td><td>2,7</td><td colspan="2">3,2</td><td>3,7</td><td>4,2</td><td>5,0</td><td>5,5</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td>г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="14%"><col width="17%"><col width="11%"><col width="6%"><col width="3%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="5" rowspan="2">Сборка змеевиков под сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 74, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид змеевика</td><td>Габариты змеевика</td><td colspan="7">Диаметр трубы d, мм, до</td></tr>
<tr><td rowspan="2">Д или L, мм, до</td><td>25</td><td colspan="2">33</td><td>45</td><td>57</td><td>76</td><td>89</td></tr>
<tr><td colspan="7">Время на один стык змеевика Т, чел.-мин.</td></tr>
<tr><td>10</td><td rowspan="3">Плоский (вид Б)</td><td>4000</td><td>2,8</td><td colspan="2">3,3</td><td>3,9</td><td>4,6</td><td>5,4</td><td>5,9</td></tr>
<tr><td>11</td><td>5000</td><td>-</td><td colspan="2">3,5</td><td>4,2</td><td>4,8</td><td>5,7</td><td>6,2</td></tr>
<tr><td>12</td><td>6000</td><td>-</td><td colspan="2">-</td><td>4,4</td><td>5,0</td><td>5,9</td><td>6,5</td></tr>
<tr><td>13</td><td>Круглый плоский</td><td>500</td><td>3,4</td><td colspan="2">3,8</td><td>4,8</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td rowspan="5">(вид В)</td><td>1000</td><td>3,9</td><td colspan="2">4,5</td><td>5,6</td><td>6,4</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>1500</td><td>4,4</td><td colspan="2">4,9</td><td>6,1</td><td>7,1</td><td>8,3</td><td>9,1</td></tr>
<tr><td>16</td><td>2000</td><td>4,9</td><td colspan="2">5,8</td><td>7,0</td><td>8,1</td><td>9,6</td><td>10,5</td></tr>
<tr><td>17</td><td>3000</td><td>-</td><td colspan="2">7,0</td><td>8,5</td><td>9,8</td><td>11,6</td><td>12,7</td></tr>
<tr><td>18</td><td>4000</td><td>-</td><td colspan="2">-</td><td>9,7</td><td>11,2</td><td>13,3</td><td>14,6</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td>г</td><td>д</td><td>е</td></tr>
</table>


<a id="p104393"></a>Примечания:
1. <a id="p104394"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="38%"><col width="20%"><col width="22%"><col width="20%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td></tr>
</table>


2. <a id="p104397"></a>Работа выполняется бригадой из двух человек:

                               0,37    0,59
<a id="p104398"></a>                 Т = 0,0334 х Д     х d       поз. 1...6;

                               0,24    0,57
<a id="p104399"></a>                 Т = 0,0623 х L     х d       поз. 7...12;

                              0,23    0,58
<a id="p104400"></a>                 Т = 0,126 х Д     х d        поз. 13...15;

                                0,47    0,6
<a id="p104401"></a>                 Т = 0,02008 х Д     х d      поз. 16...18.


<table>
<colgroup><col width="9%"><col width="15%"><col width="23%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"><col width="9%"></colgroup>
<tr><td colspan="4" rowspan="2">Сборка труб на фланцевом соединении</td><td colspan="4">Слесарно-сборочные работы</td></tr>
<tr><td colspan="4">Карта 75, лист 1</td></tr>
<tr><td colspan="8">(рисунок не приводится)</td></tr>
<tr><td colspan="8">Содержание работы</td></tr>
<tr><td colspan="8">1. Подать трубу к месту сборки.</td></tr>
<tr><td colspan="8">2. Установить трубы под сборку.</td></tr>
<tr><td colspan="8">3. Установить прокладку.</td></tr>
<tr><td colspan="8">4. Собрать трубы на фланцевом соединении.</td></tr>
<tr><td colspan="8">5. Закрепить фланцевое соединение.</td></tr>
<tr><td colspan="8">6. Снять узел, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина трубы L,</td><td>К-во крепежных деталей n,</td><td colspan="5">Диаметр трубы Д, мм, до</td></tr>
<tr><td rowspan="2">м, до</td><td rowspan="2">шт., до</td><td>76</td><td>95</td><td>121</td><td>159</td><td>273</td></tr>
<tr><td colspan="5">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">3</td><td>4</td><td>4,2</td><td>4,4</td><td>4,6</td><td>4,9</td><td>5,5</td></tr>
<tr><td>2</td><td>8</td><td>5,9</td><td>6,2</td><td>6,5</td><td>6,9</td><td>7,8</td></tr>
<tr><td>3</td><td>12</td><td>7,2</td><td>7,6</td><td>7,9</td><td>8,5</td><td>9,5</td></tr>
<tr><td>4</td><td>16</td><td>8,3</td><td>8,7</td><td>9,2</td><td>9,8</td><td>11,0</td></tr>
<tr><td>5</td><td rowspan="4">6</td><td>4</td><td>4,5</td><td>4,8</td><td>5,1</td><td>5,4</td><td>6,1</td></tr>
<tr><td>6</td><td>8</td><td>6,5</td><td>6,8</td><td>7,2</td><td>7,7</td><td>8,6</td></tr>
<tr><td>7</td><td>12</td><td>7,9</td><td>8,4</td><td>8,8</td><td>9,4</td><td>10,6</td></tr>
<tr><td>8</td><td>16</td><td>9,2</td><td>9,7</td><td>10,2</td><td>10,8</td><td>12,2</td></tr>
<tr><td>9</td><td rowspan="4">9</td><td>4</td><td>4,9</td><td>5,1</td><td>5,4</td><td>5,8</td><td>6,5</td></tr>
<tr><td>10</td><td>8</td><td>6,9</td><td>7,3</td><td>7,7</td><td>8,1</td><td>9,2</td></tr>
<tr><td>11</td><td>12</td><td>8,5</td><td>8,9</td><td>9,4</td><td>9,9</td><td>11,2</td></tr>
<tr><td>12</td><td>16</td><td>9,8</td><td>10,3</td><td>10,9</td><td>11,5</td><td>12,9</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td></tr>
</table>



<table>
<colgroup><col width="9%"><col width="15%"><col width="23%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"><col width="9%"></colgroup>
<tr><td colspan="4" rowspan="2">Сборка труб на фланцевом соединении</td><td colspan="4">Слесарно-сборочные работы</td></tr>
<tr><td colspan="4">Карта 75, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина трубы L,</td><td>К-во крепежных деталей n,</td><td colspan="5">Диаметр трубы Д, мм, до</td></tr>
<tr><td rowspan="2">мм, до</td><td rowspan="2">шт., до</td><td>76</td><td>95</td><td>121</td><td>159</td><td>273</td></tr>
<tr><td colspan="5">Время Т, чел.-мин.</td></tr>
<tr><td>13</td><td rowspan="4">12,5</td><td>4</td><td>5,1</td><td>5,4</td><td>5,7</td><td>6,1</td><td>6,8</td></tr>
<tr><td>14</td><td>8</td><td>7,3</td><td>7,6</td><td>8,1</td><td>8,6</td><td>9,6</td></tr>
<tr><td>15</td><td>12</td><td>8,9</td><td>9,4</td><td>9,9</td><td>10,5</td><td>11,8</td></tr>
<tr><td>16</td><td>16</td><td>10,3</td><td>10,8</td><td>11,4</td><td>12,1</td><td>13,6</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td></tr>
</table>


<a id="p104434"></a>Примечания:
1. <a id="p104435"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="35%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="6">Давление в МПа, до</td></tr>
<tr><td>времени</td><td>0,6</td><td>1,6</td><td>2,5</td><td>4,0</td><td>6,4</td><td>10,0</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,05</td><td>1,1</td><td>1,15</td><td>1,20</td><td>1,25</td></tr>
</table>


2. <a id="p104438"></a>Работа выполняется одним человеком:

                                     0,5    0,22
<a id="p104439"></a>                         Т = 0,68 х n    х Д    .


<table>
<colgroup><col width="14%"><col width="29%"><col width="12%"><col width="3%"><col width="9%"><col width="11%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="4" rowspan="2">Сборка патрубков с трубами под сварку</td><td colspan="4">Слесарно-сборочные работы</td></tr>
<tr><td colspan="4">Карта 76, лист 1</td></tr>
<tr><td colspan="8">Содержание работы</td></tr>
<tr><td colspan="8">1. Подать патрубок к месту сборки.</td></tr>
<tr><td colspan="8">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="8">3. Установить трубу в положение, удобное для сборки.</td></tr>
<tr><td colspan="8">4. Подогнать стык патрубка и трубы под сварку.</td></tr>
<tr><td colspan="8">5. Прихватить патрубок электросваркой.</td></tr>
<tr><td colspan="8">6. Зачистить места прихваток.</td></tr>
<tr><td colspan="8">7. Снять узел, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Наружный диаметр патрубка Д, мм, до</td><td colspan="6">Толщина стенки патрубка h, мм, до</td></tr>
<tr><td>2</td><td colspan="2">4</td><td>8</td><td>12</td><td>16</td></tr>
<tr><td colspan="6">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>18</td><td>3,1</td><td colspan="2">3,4</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>32</td><td>3,7</td><td colspan="2">4,1</td><td>4,7</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>57</td><td>4,4</td><td colspan="2">5,0</td><td>5,6</td><td>6,8</td><td>-</td></tr>
<tr><td>4</td><td>76</td><td>4,8</td><td colspan="2">5,4</td><td>6,1</td><td>7,5</td><td>8,6</td></tr>
<tr><td>5</td><td>108</td><td>-</td><td colspan="2">6,1</td><td>6,8</td><td>8,4</td><td>9,6</td></tr>
<tr><td>6</td><td>140</td><td>-</td><td colspan="2">-</td><td>7,5</td><td>9,1</td><td>10,5</td></tr>
<tr><td>7</td><td>180</td><td>-</td><td colspan="2">-</td><td>8,1</td><td>9,9</td><td>11,3</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td>г</td><td>д</td></tr>
</table>


<a id="p104459"></a>Примечания:
1. <a id="p104460"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="25%"><col width="17%"><col width="14%"><col width="12%"><col width="17%"><col width="15%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="3">Материал</td><td colspan="2">Установка патрубков</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>вертикальных</td><td>наклонных</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,2</td></tr>
</table>



<a id="p104465"></a><a id="p104466"></a><a id="p104467"></a>

<table>
<colgroup><col width="58%"><col width="42%"></colgroup>
<tr><td rowspan="2">Сборка патрубков с трубами под сварку</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 76, лист 2</td></tr>
<tr><td>2. Работа выполняется одним человеком:</td><td></td></tr>
<tr><td>0,32 0,17 Т = 1,08 х Д х h</td><td>для h &lt;= 8 поз. 1...7;</td></tr>
<tr><td>0,32 0,49 Т = 0,554 х Д х h</td><td>для h &gt; 8 поз. 1...7.</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="13%"><col width="10%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="14">Сборка лап или опор Слесарно-сборочные работы</td></tr>
<tr><td colspan="14">Карта 77, лист 1</td></tr>
<tr><td colspan="14">(рисунок не приводится)</td></tr>
<tr><td colspan="14">Содержание работы</td></tr>
<tr><td colspan="14">1. Подать детали лапы или опоры к месту сборки.</td></tr>
<tr><td colspan="14">2. Установить детали лапы или опоры на сборочную плиту, зачистить кройки под сварку.</td></tr>
<tr><td colspan="14">3. Выставить детали на подошву, сваркой подогнать и прихватить электросваркой.</td></tr>
<tr><td colspan="14">4. Выправить лапу или опору.</td></tr>
<tr><td colspan="14">5. Зачистить места прихваток.</td></tr>
<tr><td colspan="14">6. Снять лапу или опору, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>К-во дет. в лапе</td><td>Толщина металла</td><td colspan="11">Наибольший размер лапы или опоры А, мм, до</td></tr>
<tr><td>или опоре n, шт.,</td><td rowspan="2">h, мм, до</td><td>200</td><td>300</td><td>400</td><td>600</td><td>900</td><td>1200</td><td>1600</td><td>2000</td><td>2400</td><td>2800</td><td>3200</td></tr>
<tr><td>до</td><td colspan="11">Время на лапу или опору Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">4</td><td>4</td><td>4,2</td><td>5,2</td><td>6,0</td><td>7,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>8</td><td>4,7</td><td>5,8</td><td>6,7</td><td>8,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>16</td><td>-</td><td>6,4</td><td>7,4</td><td>9,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>30</td><td>-</td><td>-</td><td>8,2</td><td>10,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td rowspan="4">6</td><td>4</td><td>-</td><td>7,4</td><td>8,5</td><td>10,6</td><td>13,0</td><td>15,2</td><td>17,6</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>8</td><td>-</td><td>8,2</td><td>9,5</td><td>11,7</td><td>14,5</td><td>16,8</td><td>19,5</td><td>21,9</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td>16</td><td>-</td><td>9,1</td><td>10,5</td><td>13,0</td><td>16,1</td><td>18,7</td><td>21,7</td><td>24,3</td><td>26,7</td><td>28,9</td><td>31,7</td></tr>
<tr><td>8</td><td>30</td><td>-</td><td>-</td><td>-</td><td>14,3</td><td>17,6</td><td>20,5</td><td>23,4</td><td>26,7</td><td>29,4</td><td>31,4</td><td>34,1</td></tr>
<tr><td>9</td><td rowspan="3">8</td><td>4</td><td>-</td><td>9,3</td><td>10,8</td><td>13,3</td><td>16,5</td><td>19,1</td><td>29,2</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>6</td><td>-</td><td>10,3</td><td>11,9</td><td>14,8</td><td>18,3</td><td>21,2</td><td>24,6</td><td>27,6</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td>16</td><td>-</td><td>-</td><td>13,3</td><td>16,4</td><td>20,3</td><td>23,5</td><td>27,3</td><td>30,7</td><td>33,7</td><td>36,6</td><td>39,2</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="13%"><col width="10%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="14">Сборка лап или опор Слесарно-сборочные работы</td></tr>
<tr><td colspan="14">Карта 77, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>К-во дет. в лапе</td><td>Толщина металла</td><td colspan="11">Наибольший размер лапы или опоры А, мм, до</td></tr>
<tr><td>или опоре n, шт.,</td><td rowspan="2">h, мм, до</td><td>200</td><td>300</td><td>400</td><td>600</td><td>900</td><td>1200</td><td>1600</td><td>2000</td><td>2400</td><td>2800</td><td>3200</td></tr>
<tr><td>до</td><td colspan="11">Время на лапу или опору Т, чел.-мин.</td></tr>
<tr><td>12</td><td></td><td>30</td><td>-</td><td>-</td><td>-</td><td>18,0</td><td>22,3</td><td>25,9</td><td>30,0</td><td>33,7</td><td>37,1</td><td>43,1</td><td>49,9</td></tr>
<tr><td>13</td><td rowspan="4">10</td><td>4</td><td>-</td><td>11,8</td><td>13,7</td><td>16,9</td><td>20,9</td><td>24,3</td><td>28,3</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td>8</td><td>-</td><td>-</td><td>15,2</td><td>18,8</td><td>23,3</td><td>27,0</td><td>31,4</td><td>35,2</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>16</td><td>-</td><td>-</td><td>-</td><td>20,9</td><td>25,8</td><td>29,9</td><td>34,8</td><td>39,1</td><td>42,9</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td>30</td><td>-</td><td>-</td><td>-</td><td>22,9</td><td>28,3</td><td>32,9</td><td>38,2</td><td>42,9</td><td>47,2</td><td>51,2</td><td>54,8</td></tr>
<tr><td>17</td><td rowspan="4">12</td><td>4</td><td>-</td><td>14,4</td><td>16,7</td><td>20,6</td><td>25,5</td><td>29,6</td><td>34,4</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>18</td><td>8</td><td>-</td><td>-</td><td>18,6</td><td>22,9</td><td>28,3</td><td>32,9</td><td>38,2</td><td>42,8</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td>16</td><td>-</td><td>-</td><td>-</td><td>-</td><td>31,4</td><td>36,5</td><td>42,4</td><td>47,6</td><td>52,2</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>30</td><td>-</td><td>-</td><td>-</td><td>-</td><td>34,5</td><td>40,1</td><td>46,5</td><td>52,3</td><td>57,5</td><td>62,3</td><td>66,8</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>


<a id="p104504"></a>Примечания:
1. <a id="p104505"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="32%"><col width="12%"><col width="20%"><col width="20%"><col width="15%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="4">Сборка лап или опор</td></tr>
<tr><td>на плите</td><td>в специальном приспособлении</td><td>цилиндрических</td><td>конических</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>0,5</td><td>1,0</td><td>1,2</td></tr>
</table>


2. <a id="p104508"></a>Работа выполняется бригадой из двух человек:

                          0,5    0,15    0,52
<a id="p104509"></a>             Т = 0,109 х n    х h     х А          поз. 1...8;

                           1,08    0,15    0,52
<a id="p104510"></a>             Т = 0,0412 х n     х h     х А        поз. 9...20.


<table>
<colgroup><col width="6%"><col width="14%"><col width="14%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="9%"><col width="9%"><col width="8%"><col width="9%"></colgroup>
<tr><td colspan="11">Сборка смотровых окон Слесарно-сборочные работы</td></tr>
<tr><td colspan="11">Карта 78</td></tr>
<tr><td colspan="11">Вид А Вид Б (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">1. Подать детали смотрового окна к месту сборки.</td></tr>
<tr><td colspan="11">2. Уложить детали смотрового окна на сборочную плиту.</td></tr>
<tr><td colspan="11">3. Прихватить электросваркой фланец смотрового окна к бобышке или к штуцеру.</td></tr>
<tr><td colspan="11">4. Собрать смотровое окно и закрепить болтами или шпильками.</td></tr>
<tr><td colspan="11">5. Зачистить места прихваток.</td></tr>
<tr><td colspan="11">6. Снять окно, отложить.</td></tr>
<tr><td rowspan="5">N позиции</td><td>Вид крепежных</td><td>Диаметр в свету</td><td colspan="8">Смотровое окно</td></tr>
<tr><td rowspan="4">деталей</td><td rowspan="4">Д, мм, до</td><td colspan="4">на бобышке (вид А)</td><td colspan="4">на штуцере (вид Б)</td></tr>
<tr><td colspan="8">Количество крепежных деталей n, шт., до</td></tr>
<tr><td>6</td><td>8</td><td>12</td><td>16</td><td>6</td><td>8</td><td>12</td><td>16</td></tr>
<tr><td colspan="8">Время на окно Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">Болты</td><td>80</td><td>3,7</td><td>4,5</td><td>5,9</td><td>-</td><td>5,9</td><td>6,8</td><td>8,5</td><td>-</td></tr>
<tr><td>2</td><td>125</td><td>4,4</td><td>5,3</td><td>6,9</td><td>8,4</td><td>7,0</td><td>8,1</td><td>10,0</td><td>11,7</td></tr>
<tr><td>3</td><td>150</td><td>-</td><td>5,7</td><td>7,4</td><td>9,0</td><td>-</td><td>8,7</td><td>10,8</td><td>12,5</td></tr>
<tr><td>4</td><td rowspan="3">Шпильки</td><td>80</td><td>8,8</td><td>11,3</td><td>16,1</td><td>-</td><td>11,9</td><td>14,6</td><td>19,4</td><td>-</td></tr>
<tr><td>5</td><td>125</td><td>9,9</td><td>12,7</td><td>18,1</td><td>23,3</td><td>13,0</td><td>15,9</td><td>21,2</td><td>25,9</td></tr>
<tr><td>6</td><td>150</td><td>-</td><td>13,3</td><td>19,0</td><td>24,4</td><td>-</td><td>16,6</td><td>22,0</td><td>26,9</td></tr>
<tr><td></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p104529"></a>*Примечание.* Работа выполняется одним человеком:

                        0,38    0,67
<a id="p104530"></a>            Т = 0,21 х Д     х n        на бобышке    поз. 1...3;

                         0,38    0,52
<a id="p104531"></a>            Т = 0,441 х Д     х n       на штуцере    поз. 1...3;

                         0,26    0,87
<a id="p104532"></a>            Т = 0,594 х Д     х n       на бобышке    поз. 4...6;

                        0,2    0,7
<a id="p104533"></a>            Т = 1,42 х Д    х n         на штуцере    поз. 4...6.


<table>
<colgroup><col width="9%"><col width="17%"><col width="17%"><col width="11%"><col width="6%"><col width="3%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="5" rowspan="2">Сборка площадок котлов под сварку</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 79, лист 1</td></tr>
<tr><td colspan="10">Вид А Вид Б (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Подать детали площадки к месту сборки.</td></tr>
<tr><td colspan="10">2. Уложить детали на сборочную плиту.</td></tr>
<tr><td colspan="10">3. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="10">4. Подогнать детали между собой и прихватить электросваркой.</td></tr>
<tr><td colspan="10">5. Зачистить места прихваток.</td></tr>
<tr><td colspan="10">6. Снять площадку, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Характер соединения</td><td>Количество деталей в</td><td colspan="7">Масса М, кг, до</td></tr>
<tr><td rowspan="2">детали</td><td rowspan="2">сборке n, шт., до</td><td>55</td><td colspan="2">80</td><td>120</td><td>180</td><td>260</td><td>380</td></tr>
<tr><td colspan="7">Время на площадку Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">Поперечное (вид А)</td><td>2</td><td>3,2</td><td colspan="2">4,0</td><td>5,3</td><td>6,8</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>3</td><td>-</td><td colspan="2">6,3</td><td>8,2</td><td>10,7</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>4</td><td>-</td><td colspan="2">-</td><td>11,3</td><td>14,6</td><td>18,6</td><td>-</td></tr>
<tr><td>4</td><td>5</td><td>-</td><td colspan="2">-</td><td>-</td><td>18,7</td><td>23,8</td><td>30,4</td></tr>
<tr><td>5</td><td rowspan="2">Продольное (вид Б)</td><td>2</td><td>4,0</td><td colspan="2">5,1</td><td>6,7</td><td>8,7</td><td>-</td><td>-</td></tr>
<tr><td>6</td><td>3</td><td>-</td><td colspan="2">8,0</td><td>10,5</td><td>13,6</td><td>17,3</td><td>-</td></tr>
<tr><td></td><td>Индекс</td><td></td><td>а</td><td colspan="2">б</td><td>в</td><td>г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="60%"><col width="40%"></colgroup>
<tr><td rowspan="2">Сборка площадок котлов под сварку</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 79, лист 2</td></tr>
</table>


<a id="p104554"></a>Примечания:
1. <a id="p104555"></a>Нормативы времени рассчитаны на сборку площадок из углеродистой рифленой стали.
2. <a id="p104556"></a>При измененных условиях сборки приведенное в нормативной карте время применяется с коэффициентами:


<a id="p104559"></a><a id="p104560"></a><a id="p104561"></a>

<table>
<colgroup><col width="55%"><col width="22%"><col width="23%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="2">Толщина стали, мм</td></tr>
<tr><td>до 6</td><td>св. 6</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,2</td></tr>
<tr><td>3. Работа выполняется бригадой из двух человек:</td><td></td><td></td></tr>
<tr><td>1,1</td><td>0,65</td><td></td></tr>
<tr><td>Т = 0,109 х n х М</td><td>поз. 1...4;</td><td></td></tr>
<tr><td>1,1</td><td>0,65</td><td></td></tr>
<tr><td>Т = 0,139 х n х М</td><td>поз. 5...6.</td><td></td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="11%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="14">Установка вертикальных штуцеров Слесарно-сборочные работы</td></tr>
<tr><td colspan="14">Карта 80, лист 1</td></tr>
<tr><td colspan="14">Вид А Вид Б (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="14">Вид В Вид Г (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="14">Содержание работы</td></tr>
<tr><td colspan="14">1. Подать штуцер к месту сборки.</td></tr>
<tr><td colspan="14">2. Подрубить, зачистить и подогнать отверстие под штуцер в корпусе.</td></tr>
<tr><td colspan="14">3. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="14">4. Установить штуцер на корпус, подогнать с выверкой.</td></tr>
<tr><td colspan="14">5. Прихватить штуцер к корпусу электросваркой.</td></tr>
<tr><td colspan="14">6. Зачистить места прихваток.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид поверхности установ.</td><td>Толщина корпуса</td><td colspan="11">Диаметр штуцера Д, мм, до</td></tr>
<tr><td rowspan="2">h, мм, до</td><td>25</td><td>50</td><td>83</td><td>120</td><td>160</td><td>220</td><td>300</td><td>350</td><td>450</td><td>600</td><td>820</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="6">Плоская (вид А)</td><td>6</td><td>3,1</td><td>3,9</td><td>4,6</td><td>5,1</td><td>5,6</td><td>7,1</td><td>8,9</td><td>10,0</td><td>12,1</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>10</td><td>3,8</td><td>4,8</td><td>5,6</td><td>6,4</td><td>7,0</td><td>8,8</td><td>11,1</td><td>12,4</td><td>14,9</td><td>18,5</td><td>-</td></tr>
<tr><td>3</td><td>14</td><td>4,4</td><td>5,5</td><td>6,5</td><td>7,3</td><td>8,0</td><td>10,4</td><td>12,7</td><td>14,3</td><td>17,3</td><td>21,3</td><td>26,9</td></tr>
<tr><td>4</td><td>20</td><td>-</td><td>6,4</td><td>7,6</td><td>8,5</td><td>9,3</td><td>11,7</td><td>14,8</td><td>16,6</td><td>20,1</td><td>24,8</td><td>31,3</td></tr>
<tr><td>5</td><td>26</td><td>-</td><td>7,2</td><td>8,4</td><td>9,5</td><td>10,4</td><td>13,1</td><td>16,5</td><td>19,3</td><td>21,4</td><td>27,8</td><td>34,9</td></tr>
<tr><td>6</td><td>32</td><td>-</td><td>-</td><td>9,2</td><td>10,4</td><td>11,3</td><td>14,3</td><td>18,5</td><td>20,3</td><td>24,7</td><td>30,2</td><td>38,1</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="11%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="14">Установка вертикальных штуцеров Слесарно-сборочные работы</td></tr>
<tr><td colspan="14">Карта 80, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид поверхности установки</td><td>Толщина корпуса</td><td colspan="11">Диаметр штуцера Д, мм, до</td></tr>
<tr><td rowspan="2">h, мм, до</td><td>25</td><td>50</td><td>83</td><td>120</td><td>160</td><td>220</td><td>300</td><td>350</td><td>450</td><td>600</td><td>820</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>7</td><td rowspan="6">Плоская (вид А)</td><td>40</td><td>-</td><td>-</td><td>10,1</td><td>11,4</td><td>12,4</td><td>15,7</td><td>19,8</td><td>22,3</td><td>26,8</td><td>35,2</td><td>41,8</td></tr>
<tr><td>8</td><td>50</td><td>-</td><td>-</td><td>-</td><td>12,5</td><td>13,7</td><td>17,3</td><td>21,8</td><td>24,5</td><td>29,5</td><td>36,5</td><td>45,9</td></tr>
<tr><td>9</td><td>75</td><td>-</td><td>-</td><td>-</td><td>-</td><td>16,2</td><td>20,5</td><td>25,8</td><td>29,0</td><td>34,9</td><td>43,2</td><td>54,5</td></tr>
<tr><td>10</td><td>100</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>25,1</td><td>29,1</td><td>32,7</td><td>39,4</td><td>48,8</td><td>61,5</td></tr>
<tr><td>11</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>31,5</td><td>35,3</td><td>42,6</td><td>52,7</td><td>66,3</td></tr>
<tr><td>12</td><td>160</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>39,9</td><td>48,0</td><td>59,4</td><td>74,9</td></tr>
<tr><td>13</td><td>Сферическая</td><td>6</td><td>4,1</td><td>5,1</td><td>6,0</td><td>6,7</td><td>7,3</td><td>9,2</td><td>11,5</td><td>13,0</td><td>15,6</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td rowspan="11">(вид Б)</td><td>10</td><td>5,0</td><td>6,3</td><td>7,4</td><td>8,3</td><td>9,1</td><td>11,3</td><td>14,3</td><td>16,1</td><td>19,3</td><td>23,9</td><td>-</td></tr>
<tr><td>15</td><td>14</td><td>5,8</td><td>7,2</td><td>8,5</td><td>9,6</td><td>10,5</td><td>13,1</td><td>16,5</td><td>18,5</td><td>22,3</td><td>27,6</td><td>34,7</td></tr>
<tr><td>16</td><td>20</td><td>-</td><td>9,4</td><td>9,9</td><td>11,2</td><td>12,2</td><td>15,2</td><td>19,1</td><td>21,5</td><td>25,9</td><td>32,0</td><td>40,3</td></tr>
<tr><td>17</td><td>26</td><td>-</td><td>9,4</td><td>11,0</td><td>12,5</td><td>13,6</td><td>17,0</td><td>21,3</td><td>24,0</td><td>28,9</td><td>35,7</td><td>45,0</td></tr>
<tr><td>18</td><td>32</td><td>-</td><td>-</td><td>12,0</td><td>13,6</td><td>14,8</td><td>18,5</td><td>23,3</td><td>26,2</td><td>31,5</td><td>39,0</td><td>49,1</td></tr>
<tr><td>19</td><td>40</td><td>-</td><td>-</td><td>13,2</td><td>14,9</td><td>16,3</td><td>20,3</td><td>25,6</td><td>28,7</td><td>34,6</td><td>42,8</td><td>54,0</td></tr>
<tr><td>20</td><td>50</td><td>-</td><td>-</td><td>-</td><td>16,4</td><td>17,9</td><td>22,3</td><td>28,1</td><td>31,6</td><td>38,0</td><td>47,0</td><td>59,3</td></tr>
<tr><td>21</td><td>75</td><td>-</td><td>-</td><td>-</td><td>-</td><td>21,2</td><td>26,5</td><td>33,3</td><td>37,4</td><td>45,1</td><td>55,8</td><td>70,3</td></tr>
<tr><td>22</td><td>100</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>29,9</td><td>37,6</td><td>42,2</td><td>50,9</td><td>62,9</td><td>79,3</td></tr>
<tr><td>23</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>40,6</td><td>45,6</td><td>55,0</td><td>68,0</td><td>85,7</td></tr>
<tr><td>24</td><td>160</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>51,4</td><td>61,9</td><td>76,7</td><td>96,6</td></tr>
<tr><td>25</td><td rowspan="6">Цилиндрическая (вид В)</td><td>6</td><td>4,4</td><td>5,5</td><td>6,5</td><td>7,3</td><td>7,8</td><td>10,1</td><td>12,7</td><td>14,3</td><td>17,2</td><td>-</td><td>-</td></tr>
<tr><td>26</td><td>10</td><td>5,5</td><td>6,8</td><td>8,0</td><td>9,0</td><td>10,0</td><td>12,5</td><td>15,8</td><td>17,8</td><td>21,3</td><td>26,4</td><td>-</td></tr>
<tr><td>27</td><td>14</td><td>6,3</td><td>8,0</td><td>9,2</td><td>10,4</td><td>11,4</td><td>14,4</td><td>18,2</td><td>20,4</td><td>24,6</td><td>30,4</td><td>38,3</td></tr>
<tr><td>28</td><td>20</td><td>-</td><td>9,1</td><td>10,7</td><td>12,1</td><td>13,2</td><td>16,8</td><td>21,1</td><td>23,7</td><td>28,6</td><td>35,3</td><td>44,5</td></tr>
<tr><td>29</td><td>26</td><td>-</td><td>10,2</td><td>11,9</td><td>13,5</td><td>14,7</td><td>18,7</td><td>25,6</td><td>26,5</td><td>31,9</td><td>39,4</td><td>49,7</td></tr>
<tr><td>30</td><td>32</td><td>-</td><td>-</td><td>13,1</td><td>14,8</td><td>16,1</td><td>20,4</td><td>25,7</td><td>28,9</td><td>34,8</td><td>43,0</td><td>54,2</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="11%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="9" rowspan="2">Установка вертикальных штуцеров</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 80, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид поверхности установки</td><td>Толщина корпуса</td><td colspan="11">Диаметр штуцера Д, мм, до</td></tr>
<tr><td rowspan="2">h, мм, до</td><td>25</td><td>50</td><td>83</td><td>120</td><td>160</td><td>220</td><td>300</td><td>350</td><td>450</td><td>600</td><td>820</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>31</td><td rowspan="6">Цилиндрическая (вид В)</td><td>40</td><td>-</td><td>-</td><td>14,4</td><td>16,2</td><td>17,7</td><td>22,4</td><td>28,2</td><td>31,7</td><td>38,2</td><td>47,3</td><td>59,6</td></tr>
<tr><td>32</td><td>50</td><td>-</td><td>-</td><td>-</td><td>17,8</td><td>19,4</td><td>24,6</td><td>31,0</td><td>34,8</td><td>42,0</td><td>51,9</td><td>65,4</td></tr>
<tr><td>33</td><td>75</td><td>-</td><td>-</td><td>-</td><td>-</td><td>23,0</td><td>29,2</td><td>36,8</td><td>41,3</td><td>49,8</td><td>61,6</td><td>77,6</td></tr>
<tr><td>34</td><td>100</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>33,0</td><td>41,5</td><td>46,6</td><td>56,1</td><td>69,5</td><td>87,5</td></tr>
<tr><td>35</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>44,8</td><td>50,3</td><td>60,6</td><td>75,0</td><td>94,5</td></tr>
<tr><td>36</td><td>160</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>56,8</td><td>68,4</td><td>84,6</td><td>106,5</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>


<a id="p104619"></a>Примечания:
1. <a id="p104620"></a>При измененных условиях установки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="7%"><col width="7%"><col width="11%"><col width="15%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="3">Материал</td><td colspan="5">Длина штуцеров, мм, до</td><td colspan="4">Установка</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>100</td><td>300</td><td>500</td><td>800</td><td>св. 800</td><td>с подрубкой кромок</td><td>без подрубки кромок</td><td>на плоскую сферическ. цилиндр. поверх. без упора</td><td>на плоскую сферическ. цилиндр. поверх. в упор (вид Г)</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>0,8</td><td>0,85</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,0</td><td>0,6</td><td>1,0</td><td>0,3</td></tr>
</table>


2. <a id="p104623"></a>Работа выполняется бригадой из двух человек:

                 0,32    0,42
<a id="p104624"></a>    Т = 0,522 х Д     х h           для Д <= 160 мм       поз. 1...12;

                 0,74    0,42
<a id="p104625"></a>    Т = 0,062 х Д     х h           для Д > 160 мм        поз. 1...12;

                 0,32    0,42
<a id="p104626"></a>    Т = 0,683 х Д     х h           для Д <= 160 мм       поз. 13...24;

                0,74    0,42
<a id="p104627"></a>    Т = 0,08 х Д     х h            для Д > 160 мм        поз. 13...24;

                  0,32    0,42
<a id="p104628"></a>    Т = 0,0742 х Д     х h          для Д <= 160 мм       поз. 25...36;

                  0,74    0,42
<a id="p104629"></a>    Т = 0,0883 х Д     х h          для Д > 160 мм        поз. 25...36.


<table>
<colgroup><col width="5%"><col width="11%"><col width="11%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="14">Установка наклонных и тангенциальных штуцеров Слесарно-сборочные работы</td></tr>
<tr><td colspan="14">Карта 81, лист 1</td></tr>
<tr><td colspan="14">Вид А Вид Б (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="14">Вид В (рисунок не приводится)</td></tr>
<tr><td colspan="14">Содержание работы</td></tr>
<tr><td colspan="14">1. Подать штуцер к месту сборки.</td></tr>
<tr><td colspan="14">2. Подрубить, зачистить и подогнать отверстия под штуцер в корпусе.</td></tr>
<tr><td colspan="14">3. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="14">4. Установить штуцер на корпус, подогнать с выверкой.</td></tr>
<tr><td colspan="14">5. Прихватить штуцер к корпусу электросваркой.</td></tr>
<tr><td colspan="14">6. Зачистить места прихваток.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид поверхности установки</td><td>Толщина корпуса</td><td colspan="11">Диаметр штуцера Д, мм, до</td></tr>
<tr><td rowspan="2">h, мм, до</td><td>25</td><td>50</td><td>83</td><td>120</td><td>160</td><td>220</td><td>300</td><td>350</td><td>450</td><td>600</td><td>820</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="6">Цилиндрическая (вид А)</td><td>6</td><td>-</td><td>6,8</td><td>7,9</td><td>8,9</td><td>9,8</td><td>12,3</td><td>15,5</td><td>17,4</td><td>20,9</td><td>25,9</td><td>32,6</td></tr>
<tr><td>2</td><td>10</td><td>-</td><td>8,5</td><td>9,9</td><td>11,2</td><td>12,2</td><td>15,4</td><td>19,4</td><td>21,8</td><td>26,2</td><td>32,5</td><td>40,9</td></tr>
<tr><td>3</td><td>14</td><td>-</td><td>-</td><td>11,5</td><td>12,9</td><td>14,1</td><td>17,9</td><td>22,5</td><td>25,3</td><td>30,5</td><td>37,7</td><td>47,5</td></tr>
<tr><td>4</td><td>20</td><td>-</td><td>-</td><td>13,5</td><td>15,2</td><td>16,6</td><td>18,2</td><td>22,9</td><td>25,8</td><td>31,0</td><td>38,4</td><td>48,4</td></tr>
<tr><td>5</td><td>26</td><td>-</td><td>-</td><td>15,1</td><td>17,0</td><td>18,6</td><td>23,5</td><td>39,6</td><td>33,3</td><td>40,1</td><td>49,6</td><td>62,4</td></tr>
<tr><td>6</td><td>32</td><td>-</td><td>-</td><td>16,5</td><td>18,7</td><td>20,4</td><td>25,7</td><td>32,4</td><td>36,4</td><td>43,8</td><td>54,2</td><td>68,3</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="11%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="14">Установка наклонных и тангенциальных штуцеров Слесарно-сборочные работы</td></tr>
<tr><td colspan="14">Карта 81, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид поверхности установки</td><td>Толщина корпуса</td><td colspan="11">Диаметр штуцера Д, мм, до</td></tr>
<tr><td rowspan="2">h, мм, до</td><td>25</td><td>50</td><td>83</td><td>120</td><td>160</td><td>220</td><td>300</td><td>350</td><td>450</td><td>600</td><td>820</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>7</td><td rowspan="6">Цилиндрическая (вид А)</td><td>40</td><td>-</td><td>-</td><td>18,3</td><td>20,6</td><td>22,8</td><td>28,4</td><td>35,8</td><td>40,2</td><td>48,4</td><td>59,9</td><td>75,5</td></tr>
<tr><td>8</td><td>50</td><td>-</td><td>-</td><td>-</td><td>22,7</td><td>24,8</td><td>31,3</td><td>39,4</td><td>44,3</td><td>53,4</td><td>66,0</td><td>83,2</td></tr>
<tr><td>9</td><td>75</td><td>-</td><td>-</td><td>-</td><td>-</td><td>29,7</td><td>37,4</td><td>47,2</td><td>53,5</td><td>63,8</td><td>79,0</td><td>99,6</td></tr>
<tr><td>10</td><td>100</td><td>-</td><td>-</td><td>-</td><td>-</td><td>33,7</td><td>42,5</td><td>53,5</td><td>60,1</td><td>72,4</td><td>89,6</td><td>112,9</td></tr>
<tr><td>11</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>46,1</td><td>58,1</td><td>65,2</td><td>78,6</td><td>97,2</td><td>122,5</td></tr>
<tr><td>12</td><td>160</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>52,3</td><td>65,9</td><td>71,1</td><td>89,2</td><td>110,3</td><td>138,9</td></tr>
<tr><td>13</td><td rowspan="7">Цилиндрическая (вид Б)</td><td>6</td><td>5,7</td><td>7,1</td><td>8,4</td><td>9,4</td><td>10,3</td><td>13,0</td><td>16,4</td><td>18,4</td><td>22,2</td><td>-</td><td>-</td></tr>
<tr><td>14</td><td>10</td><td>7,1</td><td>8,9</td><td>10,5</td><td>11,9</td><td>12,9</td><td>16,3</td><td>20,5</td><td>23,0</td><td>27,7</td><td>34,3</td><td>-</td></tr>
<tr><td>15</td><td>14</td><td>8,3</td><td>10,3</td><td>12,2</td><td>13,7</td><td>15,0</td><td>18,8</td><td>23,7</td><td>26,7</td><td>32,1</td><td>39,8</td><td>50,1</td></tr>
<tr><td>16</td><td>20</td><td>-</td><td>12,1</td><td>14,2</td><td>16,0</td><td>17,5</td><td>22,1</td><td>27,8</td><td>31,2</td><td>37,7</td><td>46,6</td><td>58,7</td></tr>
<tr><td>17</td><td>26</td><td>-</td><td>13,6</td><td>16,0</td><td>18,0</td><td>19,7</td><td>24,8</td><td>31,2</td><td>35,1</td><td>42,2</td><td>52,3</td><td>65,9</td></tr>
<tr><td>18</td><td>32</td><td>-</td><td>-</td><td>17,5</td><td>19,8</td><td>21,5</td><td>27,2</td><td>34,2</td><td>38,4</td><td>46,3</td><td>57,3</td><td>72,2</td></tr>
<tr><td>19</td><td>40</td><td>-</td><td>-</td><td>19,3</td><td>21,8</td><td>23,8</td><td>30,0</td><td>37,8</td><td>42,5</td><td>51,2</td><td>63,3</td><td>79,8</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="11%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="14">Установка наклонных и тангенциальных штуцеров Слесарно-сборочные работы</td></tr>
<tr><td colspan="14">Карта 81, лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид поверхности установки</td><td>Толщина корпуса</td><td colspan="11">Диаметр штуцера Д, мм, до</td></tr>
<tr><td rowspan="2">h, мм, до</td><td>25</td><td>50</td><td>83</td><td>120</td><td>160</td><td>220</td><td>300</td><td>350</td><td>450</td><td>600</td><td>820</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>20</td><td rowspan="5">Цилиндрическая (вид Б)</td><td>50</td><td>-</td><td>-</td><td>-</td><td>24,1</td><td>26,3</td><td>33,1</td><td>41,7</td><td>46,8</td><td>56,4</td><td>69,8</td><td>87,9</td></tr>
<tr><td>21</td><td>75</td><td>-</td><td>-</td><td>-</td><td>28,8</td><td>31,4</td><td>39,6</td><td>49,8</td><td>56,0</td><td>67,4</td><td>83,4</td><td>105,2</td></tr>
<tr><td>22</td><td>100</td><td>-</td><td>-</td><td>-</td><td>32,7</td><td>35,6</td><td>44,9</td><td>56,5</td><td>63,5</td><td>76,6</td><td>94,7</td><td>119,4</td></tr>
<tr><td>23</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td><td>38,4</td><td>48,7</td><td>61,3</td><td>68,9</td><td>83,0</td><td>102,7</td><td>129,4</td></tr>
<tr><td>24</td><td>160</td><td>-</td><td>-</td><td>-</td><td>-</td><td>43,6</td><td>55,3</td><td>69,6</td><td>78,2</td><td>94,2</td><td>116,6</td><td>146,9</td></tr>
<tr><td>25</td><td>Сферическая</td><td>6</td><td>4,9</td><td>6,1</td><td>7,2</td><td>8,1</td><td>8,9</td><td>11,2</td><td>14,0</td><td>15,8</td><td>19,0</td><td>-</td><td>-</td></tr>
<tr><td>26</td><td rowspan="8">(вид В)</td><td>10</td><td>6,1</td><td>7,6</td><td>9,0</td><td>10,1</td><td>11,0</td><td>13,9</td><td>17,6</td><td>19,8</td><td>23,8</td><td>29,4</td><td>-</td></tr>
<tr><td>27</td><td>14</td><td>7,1</td><td>8,9</td><td>10,4</td><td>11,8</td><td>12,8</td><td>16,2</td><td>20,3</td><td>22,9</td><td>27,5</td><td>34,1</td><td>42,9</td></tr>
<tr><td>28</td><td>20</td><td>-</td><td>10,4</td><td>12,2</td><td>13,8</td><td>15,0</td><td>18,9</td><td>23,8</td><td>26,8</td><td>32,2</td><td>39,9</td><td>50,3</td></tr>
<tr><td>29</td><td>26</td><td>-</td><td>11,7</td><td>13,7</td><td>15,5</td><td>16,9</td><td>21,2</td><td>26,8</td><td>30,0</td><td>36,2</td><td>44,8</td><td>56,5</td></tr>
<tr><td>30</td><td>32</td><td>-</td><td>-</td><td>15,0</td><td>16,9</td><td>18,5</td><td>23,3</td><td>29,3</td><td>32,9</td><td>39,7</td><td>49,1</td><td>61,9</td></tr>
<tr><td>31</td><td>40</td><td>-</td><td>-</td><td>-</td><td>18,7</td><td>20,4</td><td>25,7</td><td>32,3</td><td>36,3</td><td>43,7</td><td>54,1</td><td>68,2</td></tr>
<tr><td>32</td><td>50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>22,5</td><td>28,3</td><td>35,7</td><td>40,1</td><td>48,3</td><td>59,8</td><td>75,4</td></tr>
<tr><td>33</td><td>75</td><td>-</td><td>-</td><td>-</td><td>-</td><td>26,9</td><td>33,8</td><td>42,6</td><td>47,9</td><td>57,7</td><td>71,4</td><td>89,9</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="11%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="14">Установка наклонных и тангенциальных штуцеров Слесарно-сборочные работы</td></tr>
<tr><td colspan="14">Карта 81, лист 4</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид поверхности установки</td><td>Толщина корпуса</td><td colspan="11">Диаметр штуцера Д, мм, до</td></tr>
<tr><td rowspan="2">h, мм, до</td><td>25</td><td>50</td><td>83</td><td>120</td><td>160</td><td>220</td><td>300</td><td>350</td><td>450</td><td>600</td><td>820</td></tr>
<tr><td colspan="11">Время Т, чел.-мин.</td></tr>
<tr><td>34</td><td>Сферическая</td><td>100</td><td>-</td><td>-</td><td>-</td><td>-</td><td>30,5</td><td>38,4</td><td>48,4</td><td>54,4</td><td>65,5</td><td>81,0</td><td>102,2</td></tr>
<tr><td>35</td><td rowspan="2">(вид В)</td><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>41,7</td><td>52,5</td><td>58,9</td><td>71,1</td><td>87,9</td><td>110,8</td></tr>
<tr><td>36</td><td>160</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>47,4</td><td>59,6</td><td>67,0</td><td>80,7</td><td>99,8</td><td>125,8</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td></tr>
</table>


<a id="p104691"></a>Примечания:
1. <a id="p104692"></a>При измененных условиях установки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="11%"><col width="11%"><col width="11%"><col width="7%"><col width="7%"><col width="5%"><col width="11%"><col width="9%"><col width="12%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="3">Материал</td><td colspan="4">Длина штуцера, мм, до</td><td colspan="2">Установка</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>300</td><td>500</td><td>800</td><td>св. 800</td><td>с подрубкой кромок</td><td>без подрубки кромок</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>0,85</td><td>0,90</td><td>1,0</td><td>1,1</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p104695"></a>Работа выполняется бригадой из двух человек:

             0,44    0,32                                              0,44    0,74
<a id="p104696"></a>Т = 0,879 х h     х Д     для Д <= 160 мм  поз. 1...12;  Т = 0,1099 х h     х Д     для Д > 160 мм   поз. 13...24;

             0,44    0,74                                             0,44    0,32
<a id="p104697"></a>Т = 0,104 х h     х Д     для Д > 160 мм   поз. 1...12;  Т = 0,795 х h     х Д      для Д <= 160 мм  поз. 25...36;

             0,44    0,32                                              0,44    0,74
<a id="p104698"></a>Т = 0,928 х h     х Д     для Д <= 160 мм  поз. 13...24; Т = 0,0941 х h     х Д     для Д > 160 мм   поз. 25...36.


<table>
<colgroup><col width="6%"><col width="31%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="10">Установка приварышей Слесарно-сборочные работы</td></tr>
<tr><td colspan="10">Карта 82, лист 1</td></tr>
<tr><td colspan="10">Вид А Вид Б (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="10">Вид В Вид Г (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="10">Содержание работы</td></tr>
<tr><td colspan="10">1. Подать приварыш к месту сборки.</td></tr>
<tr><td colspan="10">2. Зачистить на приварыше и корпусе места сварки.</td></tr>
<tr><td colspan="10">3. Установить приварыш и подогнать по отверстию корпуса или по разметке.</td></tr>
<tr><td colspan="10">4. Прихватить приварыш к корпусу электросваркой.</td></tr>
<tr><td colspan="10">5. Зачистить места прихваток.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид установки</td><td colspan="8">Диаметр или больший размер приварыша Д, мм, до</td></tr>
<tr><td>30</td><td>40</td><td>55</td><td>75</td><td>100</td><td>130</td><td>180</td><td>250</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>В отбортованное отверстие (вид А)</td><td>0,81</td><td>0,88</td><td>1,00</td><td>1,17</td><td>1,35</td><td>1,54</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>По внутреннему отверстию (вид Б)</td><td>0,97</td><td>1,06</td><td>1,15</td><td>1,34</td><td>1,55</td><td>1,77</td><td>2,08</td><td>2,45</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="31%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="9%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="10">Установка приварышей Слесарно-сборочные работы</td></tr>
<tr><td colspan="10">Карта 82, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид установки</td><td colspan="8">Диаметр или больший размер приварыша Д, мм, до</td></tr>
<tr><td>30</td><td>40</td><td>55</td><td>75</td><td>100</td><td>130</td><td>180</td><td>250</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>3</td><td>Без отверстия по разметке или по наружному отверстию (вид В и вид Г)</td><td>1,06</td><td>1,15</td><td>1,28</td><td>1,49</td><td>1,72</td><td>1,96</td><td>2,31</td><td>2,72</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p104717"></a>Примечания:
1. <a id="p104718"></a>При измененных условиях установки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="29%"><col width="12%"><col width="14%"><col width="12%"><col width="15%"><col width="17%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="3">Материал</td><td colspan="2">Установка</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>с подгонкой</td><td>без подгонки</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p104721"></a>Работа выполняется одним человеком:

             0,3                                  0,5
<a id="p104722"></a>Т = 0,291 х Д     Д < 55 мм  поз. 1; Т = 0,135 х Д     Д >= 55 мм  поз. 1;

             0,3                                  0,5
<a id="p104723"></a>Т = 0,351 х Д     Д < 55 мм  поз. 2; Т = 0,155 х Д     Д >= 55 мм  поз. 2;

             0,3                                  0,5
<a id="p104724"></a>Т = 0,381 х Д     Д < 55 мм  поз. 3; Т = 0,172 х Д     Д >= 55 мм  поз. 3.


<table>
<colgroup><col width="6%"><col width="12%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Установка закрепляющих колец</td><td colspan="6">Слесарно-сборочные работы</td></tr>
<tr><td colspan="6">Карта 83, лист 1</td></tr>
<tr><td colspan="13">Вид А Вид Б Вид В (рисунок (рисунок (рисунок не приводится) не приводится) не приводится)</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">1. Подать кольцо к месту сборки.</td></tr>
<tr><td colspan="13">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="13">3. Установить закрепляющее кольцо на корпус и подогнать.</td></tr>
<tr><td colspan="13">4. Прихватить закрепляющее кольцо к корпусу электросваркой.</td></tr>
<tr><td colspan="13">5. Зачистить места прихваток.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Поверхность</td><td>Толщина кольца</td><td colspan="10">Внутренний диаметр кольца Д, мм, до</td></tr>
<tr><td rowspan="2">установки</td><td rowspan="2">h, мм, до</td><td>80</td><td>120</td><td>160</td><td colspan="2">200</td><td>250</td><td>350</td><td>450</td><td>600</td><td>820</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="5">Плоская (вид А)</td><td>4</td><td>2,18</td><td>2,49</td><td>2,73</td><td colspan="2">3,83</td><td>4,51</td><td>4,92</td><td>6,96</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>8</td><td>2,74</td><td>3,12</td><td>3,43</td><td colspan="2">4,09</td><td>4,82</td><td>6,18</td><td>7,45</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>12</td><td>3,14</td><td>3,57</td><td>3,9</td><td colspan="2">4,67</td><td>6,48</td><td>7,07</td><td>8,51</td><td>10,5</td><td>13,3</td></tr>
<tr><td>4</td><td>16</td><td>3,45</td><td>3,93</td><td>4,31</td><td colspan="2">5,14</td><td>6,06</td><td>7,77</td><td>9,36</td><td>11,6</td><td>14,6</td></tr>
<tr><td>5</td><td>20</td><td>3,71</td><td>4,23</td><td>4,64</td><td colspan="2">5,53</td><td>6,52</td><td>8,37</td><td>10,1</td><td>12,5</td><td>15,7</td></tr>
<tr><td>6</td><td>Сферическая</td><td>4</td><td>2,75</td><td>3,13</td><td>3,43</td><td colspan="2">4,06</td><td>4,79</td><td>6,15</td><td>7,41</td><td>-</td><td>-</td></tr>
<tr><td>7</td><td rowspan="4">(вид Б)</td><td>8</td><td>3,46</td><td>3,93</td><td>4,31</td><td colspan="2">5,11</td><td>6,03</td><td>7,73</td><td>9,31</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>12</td><td>3,95</td><td>4,50</td><td>4,93</td><td colspan="2">5,84</td><td>6,89</td><td>8,83</td><td>10,6</td><td>13,2</td><td>16,6</td></tr>
<tr><td>9</td><td>16</td><td>4,34</td><td>4,94</td><td>5,42</td><td colspan="2">6,42</td><td>7,58</td><td>9,72</td><td>11,7</td><td>14,5</td><td>18,2</td></tr>
<tr><td>10</td><td>20</td><td>4,67</td><td>5,32</td><td>5,84</td><td colspan="2">6,91</td><td>8,15</td><td>10,5</td><td>12,6</td><td>15,6</td><td>19,6</td></tr>
<tr><td>11</td><td>Цилиндрическая (вид В)</td><td>4</td><td>3,03</td><td>3,45</td><td>3,78</td><td colspan="2">4,47</td><td>5,27</td><td>6,76</td><td>8,15</td><td>-</td><td>-</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="12%"><col width="12%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Установка закрепляющих колец</td><td colspan="6">Слесарно-сборочные работы</td></tr>
<tr><td colspan="6">Карта 83, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Поверхность</td><td>Толщина кольца</td><td colspan="10">Внутренний диаметр кольца Д, мм, до</td></tr>
<tr><td rowspan="2">установки</td><td rowspan="2">h, мм, до</td><td>80</td><td>120</td><td>160</td><td colspan="2">200</td><td>250</td><td>350</td><td>450</td><td>600</td><td>820</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>12</td><td rowspan="4">Цилиндрическая (вид В)</td><td>8</td><td>3,81</td><td>4,34</td><td>4,76</td><td colspan="2">5,62</td><td>6,63</td><td>8,50</td><td>10,2</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td>12</td><td>4,35</td><td>4,96</td><td>5,44</td><td colspan="2">6,42</td><td>7,58</td><td>9,71</td><td>11,7</td><td>14,5</td><td>18,2</td></tr>
<tr><td>14</td><td>16</td><td>4,79</td><td>5,45</td><td>5,98</td><td colspan="2">7,06</td><td>8,33</td><td>10,7</td><td>12,9</td><td>15,9</td><td>20,0</td></tr>
<tr><td>15</td><td>20</td><td>5,16</td><td>5,87</td><td>6,44</td><td colspan="2">7,60</td><td>8,97</td><td>10,5</td><td>13,9</td><td>17,2</td><td>21,6</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p104755"></a>Примечания:
1. <a id="p104756"></a>При измененных условиях установки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="34%"><col width="12%"><col width="12%"><col width="12%"><col width="15%"><col width="14%"></colgroup>
<tr><td>Факторы, влияющие на изменение нормы</td><td colspan="3">Материал</td><td colspan="2">Установка</td></tr>
<tr><td>времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>с подрубкой кромок</td><td>без подрубки кромок</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,6</td></tr>
</table>


2. <a id="p104759"></a>Работа выполняется бригадой из двух человек:

                0,33    0,32
<a id="p104760"></a>    Т = 0,34 х h     х Д            для Д <= 160 мм       поз. 1...5;

                  0,33    0,74
<a id="p104761"></a>    Т = 0,0408 х h     х Д          для Д > 160 мм        поз. 1...5;

                 0,33    0,32
<a id="p104762"></a>    Т = 0,428 х h     х Д           для Д <= 160 мм       поз. 6...10;

                 0,33    0,74
<a id="p104763"></a>    Т = 0,051 х h     х Д           для Д > 160 мм        поз. 6...10;

                 0,33    0,32
<a id="p104764"></a>    Т = 0,472 х h     х Д           для Д <= 160 мм       поз. 11...15;

                  0,33    0,74
<a id="p104765"></a>    Т = 0,0561 х h     х Д          для Д > 160 мм        поз. 11...15.


<table>
<colgroup><col width="5%"><col width="11%"><col width="14%"><col width="16%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12">Установка колец из угловой стали и полос Слесарно-сборочные работы</td></tr>
<tr><td colspan="12">Карта 84, лист 1</td></tr>
<tr><td colspan="12">Вид А Вид Б (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Подать кольцо к месту сборки.</td></tr>
<tr><td colspan="12">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="12">3. Установить на корпус кольцо из двух частей, подогнать по месту и наметить концы под обрезку.</td></tr>
<tr><td colspan="12">4. Зачистить торцы после обрезки.</td></tr>
<tr><td colspan="12">5. Установить, подогнать кольцо, установить и прихватить сборочные приспособления.</td></tr>
<tr><td colspan="12">6. Прихватить кольцо к корпусу электросваркой.</td></tr>
<tr><td colspan="12">7. Срубить сборочные приспособления.</td></tr>
<tr><td colspan="12">8. Зачистить места прихваток.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид профиля</td><td rowspan="3">Способ установки</td><td>Номер профиля</td><td colspan="8">Диаметр корпуса Д, мм, до</td></tr>
<tr><td rowspan="2">N, до</td><td>550</td><td>750</td><td>1000</td><td>1350</td><td>1800</td><td>2400</td><td>3200</td><td>4000</td></tr>
<tr><td colspan="8">Время на кольцо Т, чел.-мин.</td></tr>
<tr><td>1</td><td>Полкой внутрь</td><td rowspan="4">Угольник</td><td>3,2</td><td>8,1</td><td>10,2</td><td>12,5</td><td>15,6</td><td>19,2</td><td>23,7</td><td>29,3</td><td>34,5</td></tr>
<tr><td>2</td><td rowspan="3">(вид А)</td><td>6,3</td><td>8,5</td><td>10,6</td><td>13,1</td><td>16,3</td><td>20,2</td><td>24,8</td><td>30,7</td><td>36,1</td></tr>
<tr><td>3</td><td>9,0</td><td>8,7</td><td>10,9</td><td>13,5</td><td>16,8</td><td>20,7</td><td>25,5</td><td>31,5</td><td>37,1</td></tr>
<tr><td>4</td><td>12,5</td><td>9,4</td><td>11,8</td><td>14,5</td><td>18,1</td><td>22,3</td><td>27,5</td><td>33,9</td><td>40,1</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="14%"><col width="16%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12">Установка колец из угловой стали и полос Слесарно-сборочные работы</td></tr>
<tr><td colspan="12">Карта 84, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид профиля</td><td rowspan="3">Способ установки</td><td>Номер профиля</td><td colspan="8">Диаметр корпуса Д, мм, до</td></tr>
<tr><td rowspan="2">N, до</td><td>550</td><td>750</td><td>1000</td><td>1350</td><td>1800</td><td>2400</td><td>3200</td><td>4000</td></tr>
<tr><td colspan="8">Время на кольцо Т, чел.-мин.</td></tr>
<tr><td>5</td><td>Полкой внутрь (вид А)</td><td rowspan="6">Угольник</td><td>16,0</td><td>9,8</td><td>12,3</td><td>15,2</td><td>18,9</td><td>23,3</td><td>28,8</td><td>35,5</td><td>41,8</td></tr>
<tr><td>6</td><td>Полкой наружу</td><td>3,2</td><td>8,7</td><td>10,9</td><td>13,4</td><td>16,7</td><td>20,6</td><td>25,5</td><td>31,4</td><td>36,1</td></tr>
<tr><td>7</td><td rowspan="4">(вид Б)</td><td>6,3</td><td>9,1</td><td>11,4</td><td>14,0</td><td>17,5</td><td>21,5</td><td>26,6</td><td>32,8</td><td>38,6</td></tr>
<tr><td>8</td><td>9,0</td><td>9,8</td><td>12,3</td><td>15,1</td><td>18,8</td><td>23,2</td><td>28,7</td><td>35,4</td><td>41,6</td></tr>
<tr><td>9</td><td>12,5</td><td>10,4</td><td>13,0</td><td>16,0</td><td>19,9</td><td>24,6</td><td>30,4</td><td>37,5</td><td>44,1</td></tr>
<tr><td>10</td><td>16,0</td><td>10,8</td><td>13,6</td><td>16,8</td><td>20,7</td><td>25,7</td><td>31,7</td><td>39,2</td><td>46,1</td></tr>
<tr><td>11</td><td rowspan="5">-</td><td rowspan="5">Полоса</td><td>1 (40 х 14)</td><td>9,2</td><td>11,6</td><td>14,3</td><td>17,8</td><td>22,0</td><td>27,1</td><td>33,5</td><td>39,4</td></tr>
<tr><td>12</td><td>2 (60 х 20)</td><td>9,9</td><td>12,5</td><td>15,4</td><td>19,2</td><td>23,7</td><td>29,3</td><td>36,1</td><td>42,5</td></tr>
<tr><td>13</td><td>3 (100 х 30)</td><td>10,4</td><td>13,1</td><td>16,2</td><td>20,1</td><td>24,8</td><td>30,6</td><td>37,8</td><td>44,5</td></tr>
<tr><td>14</td><td>4 (120 х 30)</td><td>10,8</td><td>13,5</td><td>16,7</td><td>20,8</td><td>25,6</td><td>31,6</td><td>38,9</td><td>45,9</td></tr>
<tr><td>15</td><td>5 (140 х 30)</td><td>11,0</td><td>13,8</td><td>17,1</td><td>21,3</td><td>26,3</td><td>32,4</td><td>39,9</td><td>47,0</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p104799"></a>Примечания:
1. <a id="p104800"></a>При измененных условиях установки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="11%"><col width="11%"><col width="9%"><col width="9%"><col width="9%"><col width="10%"><col width="9%"><col width="9%"><col width="8%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="5">Место установки кольца</td><td colspan="4">Вид кольца</td></tr>
<tr><td>изменение нормы времени</td><td>на цилиндрические корпусы</td><td>на эллиптические корпусы</td><td>на конусные корпусы</td><td>снаружи корпуса</td><td>внутрь корпуса</td><td>цельное на край обечайки</td><td>из двух частей</td><td>из трех частей</td><td>из четырех частей</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,0</td><td>1,2</td><td>0,8</td><td>1,0</td><td>1,2</td><td>1,6</td></tr>
</table>


2. <a id="p104803"></a>Работа выполняется бригадой из двух человек:

                        0,06    0,73
<a id="p104804"></a>          Т = 0,0746 х N     х Д         для N <= 9    поз. 1...5;

                        0,187    0,73
<a id="p104805"></a>          Т = 0,0585 х N      х Д        для N > 9     поз. 1...5.


<a id="p104808"></a><a id="p104809"></a><a id="p104810"></a>

<table>
<colgroup><col width="65%"><col width="35%"></colgroup>
<tr><td rowspan="2">Установка колец из угловой стали и полос</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 84, лист 3</td></tr>
<tr><td>0,062 0,73 Т = 0,0808 х N х Д для N &lt;= 6,3</td><td>поз. 6...10;</td></tr>
<tr><td>0,176 0,73 Т = 0,0664 х N х Д для N &gt; 6,3</td><td>поз. 6...10;</td></tr>
<tr><td>0,11 0,73 Т = 0,0925 х N х Д</td><td>поз. 11...15.</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="15%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="9%"><col width="9%"><col width="9%"><col width="11%"><col width="9%"></colgroup>
<tr><td colspan="11">Установка ребер жесткости Слесарно-сборочные работы</td></tr>
<tr><td colspan="11">Карта 85, лист 1</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">1. Подать ребра жесткости к месту сборки. (рисунок</td></tr>
<tr><td colspan="11">2. Установить и подогнать ребра жесткости не приводится) по разметке, зачистить под сварку.</td></tr>
<tr><td colspan="11">3. Обжать и прихватить электросваркой.</td></tr>
<tr><td colspan="11">4. Проверить и выправить.</td></tr>
<tr><td colspan="11">5. Зачистить места прихваток.</td></tr>
<tr><td rowspan="5">N позиции</td><td>Длина ребер</td><td colspan="9">Тип ребер жесткости</td></tr>
<tr><td rowspan="4">жесткости L, мм, до</td><td colspan="4">Полоса</td><td colspan="3">Г-образный</td><td colspan="2">Т-образный</td></tr>
<tr><td colspan="9">Толщина ребер жесткости h, мм, до</td></tr>
<tr><td>8</td><td>14</td><td>20</td><td>8</td><td>14</td><td>20</td><td>8</td><td>14</td><td>20</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td>400</td><td>3,18</td><td>4,4</td><td>5,5</td><td>3,7</td><td>5,2</td><td>6,4</td><td>4,8</td><td>6,7</td><td>8,3</td></tr>
<tr><td>2</td><td>700</td><td>4,63</td><td>6,4</td><td>8,0</td><td>4,6</td><td>6,5</td><td>8,1</td><td>6,8</td><td>9,5</td><td>11,8</td></tr>
<tr><td>3</td><td>1100</td><td>6,27</td><td>8,7</td><td>10,9</td><td>7,1</td><td>9,9</td><td>12,4</td><td>9,0</td><td>12,6</td><td>15,6</td></tr>
<tr><td>4</td><td>1600</td><td>8,06</td><td>11,3</td><td>14,0</td><td>9,0</td><td>12,7</td><td>15,7</td><td>11,4</td><td>15,9</td><td>19,7</td></tr>
<tr><td>5</td><td>2200</td><td>9,76</td><td>13,6</td><td>16,9</td><td>11,0</td><td>15,4</td><td>19,1</td><td>13,3</td><td>18,6</td><td>23,1</td></tr>
<tr><td>6</td><td>3000</td><td>12,9</td><td>18,0</td><td>22,4</td><td>14,5</td><td>20,3</td><td>25,2</td><td>17,4</td><td>24,3</td><td>30,1</td></tr>
<tr><td>7</td><td>4000</td><td>-</td><td>23,4</td><td>29,0</td><td>-</td><td>26,4</td><td>32,6</td><td>-</td><td>31,0</td><td>38,4</td></tr>
<tr><td>8</td><td>5300</td><td>-</td><td>30,1</td><td>37,3</td><td>-</td><td>34,0</td><td>42,1</td><td>-</td><td>39,4</td><td>48,8</td></tr>
<tr><td>9</td><td>8000</td><td>-</td><td>43,6</td><td>54,0</td><td>-</td><td>49,2</td><td>60,9</td><td>-</td><td>55,9</td><td>69,2</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p104830"></a>Примечания:
1. <a id="p104831"></a>При измененных условиях установки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="25%"><col width="17%"><col width="17%"><col width="23%"><col width="18%"></colgroup>
<tr><td colspan="3" rowspan="2">Установка ребер жесткости</td><td colspan="2">Слесарно-сборочные работы</td></tr>
<tr><td colspan="2">Карта 85, лист 2</td></tr>
<tr><td>Факторы, влияющие на</td><td colspan="2">Материал</td><td colspan="2">Установка</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>на цилиндрическую поверхность</td><td>на плоскую поверхность</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>1,0</td><td>0,8</td></tr>
</table>


2. <a id="p104836"></a>Работа выполняется бригадой из двух человек:

                  0,67    0,6
<a id="p104837"></a>    Т = 0,0165 х L     х h                            для L <= 1600 мм;
                                      полоса
                   0,9    0,6
<a id="p104838"></a>    Т = 0,00275 х L    х h                            для L > 1600 мм;

                  0,64    0,6
<a id="p104839"></a>    Т = 0,0232 х L     х h                            для L <= 1600 мм;
                                    Г-образный
                  0,9    0,6           тип
<a id="p104840"></a>    Т = 0,0031 х L    х h                             для L > 1600 мм;

                  0,62    0,6
<a id="p104841"></a>    Т = 0,0337 х L     х h                            для L <= 1600 мм;
                                    Т-образный
                   0,85    0,6          тип
<a id="p104842"></a>    Т = 0,00552 х L     х h                           для L > 1600 мм.


<table>
<colgroup><col width="4%"><col width="7%"><col width="11%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="3%"><col width="2%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="14" rowspan="2">Зачистка концов труб теплообменников</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 86, лист 1</td></tr>
<tr><td colspan="18">Содержание работы</td></tr>
<tr><td colspan="18">1. Установить трубу на подставку наждачного круга и поддержку. (рисунок</td></tr>
<tr><td colspan="18">2. Зачистить оба конца трубы одновременно. не приводится)</td></tr>
<tr><td colspan="18">3. Снять трубу, отложить.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Длина трубы</td><td>Длина зачистки</td><td colspan="15">Диаметр трубы Д, мм, до</td></tr>
<tr><td rowspan="2">L, м, до</td><td rowspan="2">l, мм, до</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>22</td><td>25</td><td>32</td><td>38</td><td>45</td><td colspan="2">57</td><td>70</td><td>85</td><td>110</td></tr>
<tr><td colspan="15">Время на один конец трубы Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">2</td><td>50</td><td>0,24</td><td>0,29</td><td>0,33</td><td>0,37</td><td>0,41</td><td>0,50</td><td>0,56</td><td>0,70</td><td>0,81</td><td>0,95</td><td colspan="2">1,17</td><td>1,41</td><td>1,67</td><td>2,11</td></tr>
<tr><td>2</td><td>100</td><td>0,29</td><td>0,34</td><td>0,39</td><td>0,44</td><td>0,49</td><td>0,58</td><td>0,65</td><td>0,82</td><td>0,95</td><td>1,11</td><td colspan="2">1,37</td><td>1,65</td><td>1,96</td><td>2,48</td></tr>
<tr><td>3</td><td>150</td><td>0,32</td><td>0,37</td><td>0,43</td><td>0,48</td><td>0,53</td><td>0,64</td><td>0,72</td><td>0,89</td><td>1,04</td><td>1,22</td><td colspan="2">1,50</td><td>1,81</td><td>2,16</td><td>2,72</td></tr>
<tr><td>4</td><td rowspan="3">4</td><td>50</td><td>-</td><td>-</td><td>-</td><td>0,43</td><td>0,48</td><td>0,57</td><td>0,64</td><td>0,80</td><td>0,94</td><td>1,09</td><td colspan="2">1,35</td><td>1,63</td><td>1,94</td><td>2,44</td></tr>
<tr><td>5</td><td>100</td><td>-</td><td>-</td><td>-</td><td>0,51</td><td>0,56</td><td>0,67</td><td>0,76</td><td>0,94</td><td>1,10</td><td>1,28</td><td colspan="2">1,59</td><td>1,91</td><td>2,27</td><td>2,87</td></tr>
<tr><td>6</td><td>150</td><td>-</td><td>-</td><td>-</td><td>0,56</td><td>0,62</td><td>0,74</td><td>0,83</td><td>1,04</td><td>1,21</td><td>1,41</td><td colspan="2">1,74</td><td>2,09</td><td>2,49</td><td>3,14</td></tr>
<tr><td>7</td><td rowspan="3">6</td><td>50</td><td>-</td><td>-</td><td>-</td><td>0,47</td><td>0,52</td><td>0,63</td><td>0,70</td><td>0,88</td><td>1,02</td><td>1,19</td><td colspan="2">1,47</td><td>1,77</td><td>2,11</td><td>2,66</td></tr>
<tr><td>8</td><td>100</td><td>-</td><td>-</td><td>-</td><td>0,55</td><td>0,61</td><td>0,73</td><td>0,82</td><td>1,03</td><td>1,20</td><td>1,40</td><td colspan="2">1,73</td><td>2,08</td><td>2,47</td><td>3,12</td></tr>
<tr><td>9</td><td>150</td><td>-</td><td>-</td><td>-</td><td>0,60</td><td>0,67</td><td>0,81</td><td>0,90</td><td>1,13</td><td>1,32</td><td>1,53</td><td colspan="2">1,90</td><td>2,28</td><td>2,72</td><td>3,42</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td>н</td><td>о</td></tr>
</table>



<table>
<colgroup><col width="74%"><col width="26%"></colgroup>
<tr><td rowspan="2">Зачистка концов труб теплообменников</td><td>Слесарные работы</td></tr>
<tr><td>Карта 86, лист 2</td></tr>
</table>


<a id="p104862"></a>Примечания:
1. <a id="p104863"></a>При измененных условиях зачистки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="45%"><col width="20%"><col width="20%"><col width="15%"></colgroup>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td colspan="3">Материал</td></tr>
<tr><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td></tr>
</table>


2. <a id="p104866"></a>Работа выполняется бригадой из двух человек:

                                   0,21    0,23    0,9
<a id="p104867"></a>                     Т = 0,0108 х L     х h     х Д   .


<table>
<colgroup><col width="4%"><col width="9%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="17">Установка прямых труб в каркас теплообменника Слесарно-сборочные работы</td></tr>
<tr><td colspan="17">Карта 87, лист 1</td></tr>
<tr><td colspan="17">Содержание работы</td></tr>
<tr><td colspan="17">1. Ввести в трубу направляющую головку. (рисунок</td></tr>
<tr><td colspan="17">2. Продеть трубу через отверстия решеток и перегородок. не приводится)</td></tr>
<tr><td colspan="17">3. Вынуть направляющую головку из трубы.</td></tr>
<tr><td colspan="17">4. Подогнать выступающие из решеток концы труб по одной плоскости.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Кол-во перегородок n, шт.,</td><td>Длина трубы</td><td colspan="14">Диаметр трубы Д, мм, до</td></tr>
<tr><td rowspan="2">L, м, до</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>22</td><td>25</td><td>32</td><td>38</td><td>45</td><td>57</td><td>70</td><td>85</td><td>110</td></tr>
<tr><td>до</td><td colspan="14">Время на трубу Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">2</td><td>1,0</td><td>0,35</td><td>0,39</td><td>0,43</td><td>0,47</td><td>0,51</td><td>0,58</td><td>0,63</td><td>0,69</td><td>0,81</td><td>0,95</td><td>1,18</td><td>1,42</td><td>1,70</td><td>2,16</td></tr>
<tr><td>2</td><td>2,0</td><td>0,41</td><td>0,46</td><td>0,51</td><td>0,56</td><td>0,61</td><td>0,69</td><td>0,75</td><td>0,82</td><td>0,96</td><td>1,13</td><td>1,40</td><td>1,69</td><td>2,02</td><td>2,57</td></tr>
<tr><td>3</td><td>3,0</td><td>0,46</td><td>0,52</td><td>0,57</td><td>0,62</td><td>0,67</td><td>0,76</td><td>0,83</td><td>0,91</td><td>1,07</td><td>1,25</td><td>1,55</td><td>1,87</td><td>2,24</td><td>2,84</td></tr>
<tr><td>4</td><td>4,0</td><td>-</td><td>-</td><td>-</td><td>0,67</td><td>0,72</td><td>0,82</td><td>0,89</td><td>0,98</td><td>1,15</td><td>1,34</td><td>1,66</td><td>2,01</td><td>2,41</td><td>3,05</td></tr>
<tr><td>5</td><td rowspan="4">4</td><td>2,0</td><td>0,52</td><td>0,58</td><td>0,64</td><td>0,70</td><td>0,76</td><td>0,86</td><td>0,94</td><td>1,03</td><td>1,21</td><td>1,41</td><td>1,75</td><td>2,11</td><td>2,53</td><td>3,20</td></tr>
<tr><td>6</td><td>3,0</td><td>0,57</td><td>0,64</td><td>0,71</td><td>0,77</td><td>0,83</td><td>0,95</td><td>1,04</td><td>1,14</td><td>1,33</td><td>1,55</td><td>1,93</td><td>2,33</td><td>2,80</td><td>3,55</td></tr>
<tr><td>7</td><td>4,0</td><td>-</td><td>-</td><td>-</td><td>0,83</td><td>0,90</td><td>1,03</td><td>1,11</td><td>1,22</td><td>1,43</td><td>1,67</td><td>2,08</td><td>2,51</td><td>3,01</td><td>3,81</td></tr>
<tr><td>8</td><td>5,0</td><td>-</td><td>-</td><td>-</td><td>0,88</td><td>0,95</td><td>1,08</td><td>1,18</td><td>1,29</td><td>1,51</td><td>1,77</td><td>2,20</td><td>2,66</td><td>3,18</td><td>4,03</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="17">Установка прямых труб в каркас теплообменника Слесарно-сборочные работы</td></tr>
<tr><td colspan="17">Карта 87, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Кол-во перегородок n, шт.,</td><td>Длина трубы</td><td colspan="14">Диаметр трубы Д, мм, до</td></tr>
<tr><td rowspan="2">L, м, до</td><td>10</td><td>12</td><td>14</td><td>16</td><td>18</td><td>22</td><td>25</td><td>32</td><td>38</td><td>45</td><td>57</td><td>70</td><td>85</td><td>110</td></tr>
<tr><td>до</td><td colspan="14">Время на трубу Т, чел.-мин.</td></tr>
<tr><td>9</td><td rowspan="3">6</td><td>3,0</td><td>0,65</td><td>0,73</td><td>0,81</td><td>0,88</td><td>0,95</td><td>1,09</td><td>1,18</td><td>1,30</td><td>1,52</td><td>1,77</td><td>2,20</td><td>2,66</td><td>3,18</td><td>4,04</td></tr>
<tr><td>10</td><td>4,0</td><td>-</td><td>-</td><td>-</td><td>0,95</td><td>1,02</td><td>1,17</td><td>1,27</td><td>1,39</td><td>1,63</td><td>1,91</td><td>2,37</td><td>2,86</td><td>3,42</td><td>4,34</td></tr>
<tr><td>11</td><td>5,0</td><td>-</td><td>-</td><td>-</td><td>1,00</td><td>1,08</td><td>1,23</td><td>1,34</td><td>1,47</td><td>1,72</td><td>2,02</td><td>2,51</td><td>3,03</td><td>3,62</td><td>4,59</td></tr>
<tr><td>12</td><td rowspan="3">8</td><td>4,0</td><td>-</td><td>-</td><td>-</td><td>1,04</td><td>1,12</td><td>1,25</td><td>1,39</td><td>1,52</td><td>1,79</td><td>2,09</td><td>2,59</td><td>3,14</td><td>3,75</td><td>4,75</td></tr>
<tr><td>13</td><td>5,0</td><td>-</td><td>-</td><td>-</td><td>1,10</td><td>1,19</td><td>1,35</td><td>1,47</td><td>1,61</td><td>1,89</td><td>2,21</td><td>2,75</td><td>3,32</td><td>3,97</td><td>5,03</td></tr>
<tr><td>14</td><td>6,0</td><td>-</td><td>-</td><td>-</td><td>1,15</td><td>1,24</td><td>1,42</td><td>1,54</td><td>1,69</td><td>1,98</td><td>2,31</td><td>2,87</td><td>3,47</td><td>4,15</td><td>5,26</td></tr>
<tr><td>15</td><td rowspan="3">10</td><td>4,0</td><td>-</td><td>-</td><td>-</td><td>1,12</td><td>1,21</td><td>1,37</td><td>1,49</td><td>1,64</td><td>1,92</td><td>2,24</td><td>2,79</td><td>3,37</td><td>4,03</td><td>5,11</td></tr>
<tr><td>16</td><td>5,0</td><td>-</td><td>-</td><td>-</td><td>1,18</td><td>1,27</td><td>1,45</td><td>1,58</td><td>1,73</td><td>2,03</td><td>2,37</td><td>2,95</td><td>3,56</td><td>4,25</td><td>5,40</td></tr>
<tr><td>17</td><td>6,0</td><td>-</td><td>-</td><td>-</td><td>1,23</td><td>1,33</td><td>1,52</td><td>1,65</td><td>1,82</td><td>2,13</td><td>2,48</td><td>3,69</td><td>3,73</td><td>4,46</td><td>5,65</td></tr>
<tr><td>18</td><td rowspan="2">14</td><td>5,0</td><td>-</td><td>-</td><td>-</td><td>1,32</td><td>1,42</td><td>1,62</td><td>1,76</td><td>1,93</td><td>2,26</td><td>2,64</td><td>3,29</td><td>3,97</td><td>4,75</td><td>6,02</td></tr>
<tr><td>19</td><td>6,0</td><td>-</td><td>-</td><td>-</td><td>1,38</td><td>1,49</td><td>1,69</td><td>1,84</td><td>2,02</td><td>2,37</td><td>2,77</td><td>3,44</td><td>4,16</td><td>4,97</td><td>6,30</td></tr>
<tr><td>20</td><td>18</td><td>6,0</td><td>-</td><td>-</td><td>-</td><td>1,49</td><td>1,61</td><td>1,84</td><td>1,99</td><td>2,19</td><td>2,57</td><td>3,00</td><td>3,73</td><td>4,50</td><td>5,38</td><td>6,82</td></tr>
<tr><td>21</td><td>20</td><td>6,0</td><td>-</td><td>-</td><td>-</td><td>1,54</td><td>1,67</td><td>1,90</td><td>2,06</td><td>2,27</td><td>2,65</td><td>3,10</td><td>3,86</td><td>4,66</td><td>5,57</td><td>7,06</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>



<a id="p104904"></a><a id="p104905"></a><a id="p104906"></a>

<table>
<colgroup><col width="64%"><col width="36%"></colgroup>
<tr><td rowspan="2">Установка прямых труб в каркас теплообменника</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 87, лист 3</td></tr>
<tr><td>Примечание. Работа выполняется бригадой из двух человек:</td><td></td></tr>
<tr><td>0,32 0,25 0,65 Т = 0,0624 х n х L х Д для Д &lt;= 25 мм</td><td>поз. 1...21;</td></tr>
<tr><td>0,32 0,25 0,92 Т = 0,0229 х n х L х Д для Д &gt; 25 мм</td><td>поз. 1...21.</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="18%"><col width="12%"><col width="17%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Развальцовка труб теплообменников</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 88, лист 1</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">1. Смазать отверстие трубы на длину развальцовки. (рисунок</td></tr>
<tr><td colspan="11">2. Подвести инструмент к отверстию трубы. не приводится)</td></tr>
<tr><td colspan="11">3. Развальцевать отверстие с одной стороны.</td></tr>
<tr><td colspan="11">4. Отвести инструмент.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Инструмент или приспособление</td><td>Толщина стенки трубы,</td><td rowspan="3">Диаметр трубы d, мм, до</td><td colspan="7">Длина развальцовки L, мм, до</td></tr>
<tr><td rowspan="2">мм</td><td>20</td><td>25</td><td colspan="2">30</td><td>40</td><td>50</td><td>60</td></tr>
<tr><td colspan="7">Время на одно отверстие Т, чел.-мин.</td></tr>
<tr><td>1</td><td>Пневматическая</td><td rowspan="2">1,5</td><td>12</td><td>0,19</td><td>0,23</td><td colspan="2">0,26</td><td>0,31</td><td>0,37</td><td>0,42</td></tr>
<tr><td>2</td><td>машинка (дорн,</td><td>14</td><td>0,23</td><td>0,26</td><td colspan="2">0,30</td><td>0,37</td><td>0,43</td><td>0,49</td></tr>
<tr><td>3</td><td>прошивка, роликовая</td><td rowspan="2">2</td><td>18</td><td>0,30</td><td>0,35</td><td colspan="2">0,41</td><td>0,49</td><td>0,57</td><td>0,65</td></tr>
<tr><td>4</td><td rowspan="9">вальцовка)</td><td>22</td><td>0,38</td><td>0,44</td><td colspan="2">0,50</td><td>0,61</td><td>0,71</td><td>0,82</td></tr>
<tr><td>5</td><td>2,5</td><td>25</td><td>0,44</td><td>0,50</td><td colspan="2">0,58</td><td>0,71</td><td>0,82</td><td>0,94</td></tr>
<tr><td>6</td><td rowspan="3">3</td><td>32</td><td>0,57</td><td>0,67</td><td colspan="2">0,76</td><td>0,93</td><td>1,08</td><td>1,23</td></tr>
<tr><td>7</td><td>38</td><td>0,69</td><td>0,81</td><td colspan="2">0,91</td><td>1,12</td><td>1,31</td><td>1,48</td></tr>
<tr><td>8</td><td>45</td><td>0,83</td><td>0,97</td><td colspan="2">1,10</td><td>1,35</td><td>1,58</td><td>1,79</td></tr>
<tr><td>9</td><td>3,5</td><td>57</td><td>1,07</td><td>1,26</td><td colspan="2">1,43</td><td>1,75</td><td>2,04</td><td>2,32</td></tr>
<tr><td>10</td><td rowspan="2">4</td><td>70</td><td>1,35</td><td>1,58</td><td colspan="2">1,79</td><td>2,20</td><td>2,56</td><td>2,91</td></tr>
<tr><td>11</td><td>85</td><td>1,67</td><td>1,95</td><td colspan="2">2,22</td><td>2,72</td><td>3,18</td><td>3,61</td></tr>
<tr><td>12</td><td>6</td><td>110</td><td>2,22</td><td>2,60</td><td colspan="2">2,95</td><td>3,61</td><td>4,22</td><td>4,79</td></tr>
<tr><td>13</td><td rowspan="3">Приспособление с механическим приводом</td><td rowspan="2">2</td><td>18</td><td>0,23</td><td>0,27</td><td colspan="2">0,30</td><td>0,37</td><td>0,43</td><td>0,49</td></tr>
<tr><td>14</td><td>22</td><td>0,29</td><td>0,34</td><td colspan="2">0,38</td><td>0,47</td><td>0,55</td><td>0,63</td></tr>
<tr><td>15</td><td>2,5</td><td>25</td><td>0,34</td><td>0,39</td><td colspan="2">0,45</td><td>0,55</td><td>0,65</td><td>0,73</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td>г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="18%"><col width="12%"><col width="17%"><col width="8%"><col width="8%"><col width="5%"><col width="3%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Развальцовка труб теплообменников</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 88, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Инструмент или приспособление</td><td>Толщина стенки трубы,</td><td rowspan="3">Диаметр трубы d, мм, до</td><td colspan="7">Длина развальцовки L, мм, до</td></tr>
<tr><td rowspan="2">мм</td><td>20</td><td>25</td><td colspan="2">30</td><td>40</td><td>50</td><td>60</td></tr>
<tr><td colspan="7">Время на одно отверстие Т, чел.-мин.</td></tr>
<tr><td>16</td><td rowspan="7">Приспособление с механическим приводом</td><td rowspan="3">3</td><td>32</td><td>0,46</td><td>0,54</td><td colspan="2">0,61</td><td>0,75</td><td>0,88</td><td>1,00</td></tr>
<tr><td>17</td><td>38</td><td>0,56</td><td>0,66</td><td colspan="2">0,75</td><td>0,92</td><td>1,08</td><td>1,22</td></tr>
<tr><td>18</td><td>45</td><td>0,7</td><td>0,81</td><td colspan="2">0,93</td><td>1,13</td><td>1,32</td><td>1,51</td></tr>
<tr><td>19</td><td>3,5</td><td>57</td><td>0,93</td><td>1,09</td><td colspan="2">1,24</td><td>1,52</td><td>1,77</td><td>2,02</td></tr>
<tr><td>20</td><td rowspan="2">4</td><td>70</td><td>1,19</td><td>1,39</td><td colspan="2">1,58</td><td>1,94</td><td>2,27</td><td>2,58</td></tr>
<tr><td>21</td><td>85</td><td>1,49</td><td>1,75</td><td colspan="2">1,98</td><td>2,43</td><td>2,84</td><td>3,23</td></tr>
<tr><td>22</td><td>6</td><td>110</td><td>2,04</td><td>2,38</td><td colspan="2">2,71</td><td>3,31</td><td>3,87</td><td>4,40</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td>г</td><td>д</td><td>е</td></tr>
</table>


<a id="p104942"></a>Примечания:
1. <a id="p104943"></a>При измененных условиях развальцовки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="20%"><col width="17%"><col width="20%"><col width="12%"><col width="15%"><col width="15%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="3">Материал</td><td colspan="2">Развальцовка труб поочередно</td></tr>
<tr><td>нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>одного отверстия</td><td>второго отверстия</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,7</td></tr>
</table>


2. <a id="p104946"></a>Работа выполняется бригадой из двух человек:

                                1,1    0,7
<a id="p104947"></a>                 Т = 0,00155 х d    х L       поз. 1...12;

                                 1,2    0,7
<a id="p104948"></a>                 Т = 0,000889 х d    х L      поз. 13...22.


<table>
<colgroup><col width="4%"><col width="13%"><col width="17%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="16">Торцовка труб теплообменников Слесарные работы</td></tr>
<tr><td colspan="16">Карта 89</td></tr>
<tr><td colspan="16">Содержание работы</td></tr>
<tr><td colspan="16">1. Подвести инструмент к отверстию трубы. (рисунок</td></tr>
<tr><td colspan="16">2. Подрезать торец трубы с одной стороны. не приводится)</td></tr>
<tr><td colspan="16">3. Отвести инструмент.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Инструмент</td><td rowspan="3">Материал трубы</td><td colspan="13">Диаметр и толщина стенки трубы, мм, до</td></tr>
<tr><td>10 х 1,2</td><td>12 х 1,5</td><td>14 х 1,5</td><td>18 х 2</td><td>22 х 2</td><td>25 х 2,5</td><td>32 х 3</td><td>38 х 3</td><td>45 х 3</td><td>57 х 3,5</td><td>70 х 4</td><td>85 х 4</td><td>110 х 6</td></tr>
<tr><td colspan="13">Время на один торец Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">Пневматическая машинка</td><td>Углеродистая ст.</td><td>0,20</td><td>0,23</td><td>0,27</td><td>0,32</td><td>0,38</td><td>0,45</td><td>0,55</td><td>0,65</td><td>0,75</td><td>0,95</td><td>1,15</td><td>1,25</td><td>1,35</td></tr>
<tr><td>2</td><td>Легированная ст.</td><td>0,24</td><td>0,27</td><td>0,32</td><td>0,38</td><td>0,45</td><td>0,54</td><td>0,66</td><td>0,78</td><td>0,90</td><td>1,14</td><td>1,38</td><td>1,50</td><td>1,62</td></tr>
<tr><td>3</td><td>Цветные сплавы</td><td>0,16</td><td>0,18</td><td>0,22</td><td>0,26</td><td>0,30</td><td>0,36</td><td>0,44</td><td>0,52</td><td>0,60</td><td>0,76</td><td>0,92</td><td>1,00</td><td>1,08</td></tr>
<tr><td>4</td><td rowspan="3">Приспособления с механическим приводом</td><td>Углеродистая ст.</td><td>0,30</td><td>0,33</td><td>0,36</td><td>0,39</td><td>0,43</td><td>0,46</td><td>0,50</td><td>0,55</td><td>0,60</td><td>0,70</td><td>0,85</td><td>0,95</td><td>1,05</td></tr>
<tr><td>5</td><td>Легированная ст.</td><td>0,36</td><td>0,39</td><td>0,43</td><td>0,47</td><td>0,51</td><td>0,55</td><td>0,60</td><td>0,66</td><td>0,72</td><td>0,84</td><td>1,02</td><td>1,14</td><td>1,26</td></tr>
<tr><td>6</td><td>Цветные сплавы</td><td>0,24</td><td>0,26</td><td>0,29</td><td>0,31</td><td>0,34</td><td>0,37</td><td>0,40</td><td>0,44</td><td>0,48</td><td>0,56</td><td>0,68</td><td>0,76</td><td>0,84</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>


<a id="p104963"></a>*Примечание.* Работа выполняется одним человеком.


<table>
<colgroup><col width="4%"><col width="13%"><col width="17%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="16">Отбортовка концов труб теплообменников Слесарные работы</td></tr>
<tr><td colspan="16">Карта 90</td></tr>
<tr><td colspan="16">Содержание работы</td></tr>
<tr><td colspan="16">1. Подвести инструмент к отверстию трубы. (рисунок</td></tr>
<tr><td colspan="16">2. Отбортовать оба конца трубы. не приводится)</td></tr>
<tr><td colspan="16">3. Отвести инструмент.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Инструмент</td><td rowspan="3">Материал трубы</td><td colspan="13">Диаметр и толщина стенки трубы, мм, до</td></tr>
<tr><td>10 х 1,2</td><td>12 х 1,5</td><td>14 х 1,5</td><td>18 х 2</td><td>22 х 2</td><td>25 х 2,5</td><td>32 х 3</td><td>38 х 3</td><td>45 х 3</td><td>57 х 3,5</td><td>70 х 4</td><td>85 х 4</td><td>110 х 6</td></tr>
<tr><td colspan="13">Время на трубу Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="4">Пневматическая машина</td><td>Углеродистая сталь</td><td>0,40</td><td>0,43</td><td>0,45</td><td>0,50</td><td>0,55</td><td>0,60</td><td>0,70</td><td>0,75</td><td>0,85</td><td>0,95</td><td>1,10</td><td>1,20</td><td>1,35</td></tr>
<tr><td>2</td><td rowspan="2">Легированная сталь</td><td rowspan="2">0,48</td><td rowspan="2">0,51</td><td rowspan="2">0,54</td><td rowspan="2">0,60</td><td rowspan="2">0,66</td><td rowspan="2">0,72</td><td rowspan="2">0,84</td><td rowspan="2">0,90</td><td rowspan="2">1,02</td><td rowspan="2">1,14</td><td rowspan="2">1,32</td><td rowspan="2">1,44</td><td rowspan="2">1,62</td></tr>
<tr><td rowspan="2">3</td></tr>
<tr><td>Цветные сплавы</td><td>0,32</td><td>0,34</td><td>0,36</td><td>0,40</td><td>0,44</td><td>0,48</td><td>0,56</td><td>0,60</td><td>0,68</td><td>0,76</td><td>0,88</td><td>0,96</td><td>1,08</td></tr>
<tr><td>4</td><td rowspan="2">Приспособление с механическим</td><td rowspan="2">Углеродистая сталь</td><td rowspan="2">0,30</td><td rowspan="2">0,31</td><td rowspan="2">0,32</td><td rowspan="2">0,34</td><td rowspan="2">0,38</td><td rowspan="2">0,41</td><td rowspan="2">0,50</td><td rowspan="2">0,55</td><td rowspan="2">0,60</td><td rowspan="2">0,70</td><td rowspan="2">0,85</td><td rowspan="2">0,90</td><td rowspan="2">1,05</td></tr>
<tr><td rowspan="2">5</td></tr>
<tr><td rowspan="3">приводом</td><td rowspan="2">Легированная сталь</td><td rowspan="2">0,36</td><td rowspan="2">0,37</td><td rowspan="2">0,38</td><td rowspan="2">0,41</td><td rowspan="2">0,45</td><td rowspan="2">0,49</td><td rowspan="2">0,60</td><td rowspan="2">0,66</td><td rowspan="2">0,72</td><td rowspan="2">0,84</td><td rowspan="2">1,02</td><td rowspan="2">1,08</td><td rowspan="2">1,26</td></tr>
<tr><td rowspan="2">6</td></tr>
<tr><td>Цветные сплавы</td><td>0,24</td><td>0,25</td><td>0,26</td><td>0,27</td><td>0,30</td><td>0,32</td><td>0,40</td><td>0,44</td><td>0,48</td><td>0,56</td><td>0,68</td><td>0,72</td><td>0,84</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>


<a id="p104978"></a>*Примечание.* Работа выполняется одним человеком.


```text
┌──────────────────────────────────────┬─────────────────────────┐
│ Установка стяжек для сборки обечаек  │Слесарно-сборочные работы│
│                                      ├─────────────────────────┤
│                                      │    Карта 91, лист 1     │
├──────────────────────────────────────┴─────────────────────────┤
│         Вид А                                    Вид Б         │
│(рисунок не приводится)                  (рисунок не приводится)│
│                                                                │
│                       Содержание работы                        │
│                                                                │
│I. Установка стяжки для сборки продольных стыков обечаек        │
│(вид А).                                                        │
│1. Взять стяжку.                                                │
│2. Прихватить стяжку электросваркой к обечайке.                 │
│3. Взять гаечный ключ и стянуть кромки обечайки.                │
│4. Отложить гаечный ключ.                                       │
│II. Установка стяжки для сборки поперечных стыков обечаек       │
│(вид Б).                                                        │
│1. Взять стяжку.                                                │
│2. Завести концы стяжки за торцевые кромки обечайки.            │
│3. Взять гаечный ключ и стянуть кромки обечайки.                │
│4. Отложить гаечный ключ.                                       │
├───┬───────────┬────────────────────────────────────────────────┤
│N  │  Диаметр  │                  Тип стяжки                    │
│по-│нарезанного├──────────────────┬─────────────────────────────┤
│зи-│   конца   │С приваркой концов│     Без приварки (вид Б)    │
│ции│  стержня  │     (вид А)      │                             │
│   │ стяжки Д, ├──────────────────┴─────────────────────────────┤
│   │  мм, до   │             Длина стяжки L, мм, до             │
│   │           ├─────┬─────┬──────┬─────┬─────┬─────┬─────┬─────┤
│   │           │ 300 │ 500 │ 900  │1000 │1500 │2000 │2500 │3000 │
│   │           ├─────┴─────┴──────┴─────┴─────┴─────┴─────┴─────┤
│   │           │               Время Т, чел.-мин.               │
├───┼───────────┼─────┬─────┬──────┬─────┬─────┬─────┬─────┬─────┤
│1  │22         │2,75 │3,05 │3,50  │3,1  │3,5  │3,8  │4,1  │4,3  │
├───┼───────────┼─────┼─────┼──────┼─────┼─────┼─────┼─────┼─────┤
│2  │26         │2,90 │3,25 │3,70  │3,3  │3,7  │4,0  │4,3  │4,5  │
└───┼───────────┼─────┼─────┼──────┼─────┼─────┼─────┼─────┼─────┤
    │Индекс     │  а  │  б  │  в   │  г  │  д  │  е  │  ж  │  з  │
    └───────────┴─────┴─────┴──────┴─────┴─────┴─────┴─────┴─────┘
```



<table>
<colgroup><col width="6%"><col width="18%"><col width="9%"><col width="9%"><col width="11%"><col width="6%"><col width="3%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="6" rowspan="2">Установка стяжек для сборки обечаек</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 91, лист 2</td></tr>
<tr><td rowspan="5">N позиции</td><td>Диаметр нарезанного</td><td colspan="9">Тип стяжки</td></tr>
<tr><td>конца стержня стяжки Д,</td><td colspan="3">С приваркой концов (вид А)</td><td colspan="6">Без приварки (вид Б)</td></tr>
<tr><td rowspan="3">мм, до</td><td colspan="9">Длина стяжки L, мм, до</td></tr>
<tr><td>300</td><td>500</td><td>900</td><td colspan="2">1000</td><td>1500</td><td>2000</td><td>2500</td><td>3000</td></tr>
<tr><td colspan="9">Время Т, чел.-мин.</td></tr>
<tr><td>3</td><td>36</td><td>3,25</td><td>3,60</td><td>4,10</td><td colspan="2">3,7</td><td>4,1</td><td>4,5</td><td>4,8</td><td>5,1</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p105002"></a>Примечания:
1. <a id="p105003"></a>При снятии стяжек для сборки продольного стыка (вид А) время по карте применяется с коэффициентом 0,75; для сборки поперечного стыка (вид Б) - с коэффициентом 0,5.
2. <a id="p105004"></a>При установке стяжек для сборки продольных стыков обечаек работа выполняется одним человеком; для сборки поперечных стыков - бригадой из двух человек:

                 0,34    0,22
<a id="p105005"></a>    Т = 0,273 х Д     х L            поз. 1...3        для L <= 900 мм;

                 0,34    0,28
<a id="p105006"></a>    Т = 0,159 х Д     х L            поз. 1...3        для L > 900 мм.


<table>
<colgroup><col width="5%"><col width="14%"><col width="18%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="13">Установка приспособлений для сборки Слесарно-сборочные работы цилиндрических обечаек (бандажа, стяжного обруча) Карта 92, лист 1</td></tr>
<tr><td colspan="13">Вид А Вид Б (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">1. Взять бандаж или стяжной обруч.</td></tr>
<tr><td colspan="13">2. Завести бандаж внутрь или стяжной обруч на цилиндрическую обечайку.</td></tr>
<tr><td colspan="13">3. Взять инструмент.</td></tr>
<tr><td colspan="13">4. Разжать бандаж или зажать стяжной обруч.</td></tr>
<tr><td colspan="13">5. Отложить инструмент.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Тип приспособления</td><td>Диаметр резьбы тяги</td><td colspan="10">Диаметр обечайки Д, мм, до</td></tr>
<tr><td>или стяжного болта d, мм,</td><td>400</td><td>600</td><td>800</td><td>1000</td><td>1200</td><td>1500</td><td>1800</td><td>2200</td><td>2600</td><td>3000</td></tr>
<tr><td>до</td><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="3">Бандаж (вид А)</td><td>22</td><td>1,9</td><td>2,1</td><td>2,2</td><td>2,5</td><td>2,7</td><td>3,0</td><td>3,4</td><td>3,7</td><td>4,0</td><td>4,3</td></tr>
<tr><td>2</td><td>26</td><td>2,1</td><td>2,4</td><td>2,5</td><td>2,8</td><td>3,1</td><td>3,5</td><td>3,8</td><td>4,2</td><td>4,6</td><td>4,9</td></tr>
<tr><td>3</td><td>36</td><td>2,3</td><td>2,6</td><td>2,8</td><td>3,1</td><td>3,4</td><td>3,8</td><td>4,2</td><td>4,7</td><td>5,1</td><td>5,4</td></tr>
<tr><td>4</td><td>Стяжной обруч</td><td>22</td><td>1,1</td><td>1,3</td><td>1,5</td><td>1,7</td><td>1,9</td><td>2,2</td><td>2,5</td><td>2,9</td><td>3,3</td><td>3,6</td></tr>
<tr><td>5</td><td rowspan="2">(вид Б)</td><td>26</td><td>1,3</td><td>1,5</td><td>1,7</td><td>1,9</td><td>2,2</td><td>2,4</td><td>2,9</td><td>3,3</td><td>3,7</td><td>4,1</td></tr>
<tr><td>6</td><td>36</td><td>1,4</td><td>1,7</td><td>1,8</td><td>2,1</td><td>2,4</td><td>3,2</td><td>3,4</td><td>3,6</td><td>4,1</td><td>4,5</td></tr>
<tr><td colspan="2"></td><td>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>


<a id="p105024"></a>Примечания:
1. <a id="p105025"></a>При измененных условиях установки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="24%"><col width="18%"><col width="18%"><col width="20%"><col width="20%"></colgroup>
<tr><td colspan="3" rowspan="2">Установка приспособлений для сборки цилиндрических обечаек (бандажа, стяжного обруча)</td><td colspan="2">Слесарно-сборочные работы</td></tr>
<tr><td colspan="2">Карта 92, лист 2</td></tr>
<tr><td rowspan="2">Факторы, влияющие на изменение нормы времени</td><td rowspan="2">Установка приспособлений</td><td rowspan="2">Снятие приспособлений</td><td colspan="2">Установка на обечайки</td></tr>
<tr><td>цилиндрические</td><td>эллиптические</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>0,8</td><td>1,0</td><td>1,1</td></tr>
</table>


2. <a id="p105030"></a>Работа выполняется бригадой из двух человек:

                 0,3    0,26
<a id="p105031"></a>    Т = 0,169 х d    х Д           для Д <= 800 мм          поз. 1...3;

                  0,3    0,5
<a id="p105032"></a>    Т = 0,0339 х d    х Д          для Д > 800 мм           поз. 1...3;

                  0,3    0,39
<a id="p105033"></a>    Т = 0,0468 х d    х Д          для Д <= 800 мм          поз. 4...6;

                  0,3    0,7
<a id="p105034"></a>    Т = 0,0057 х d    х Д          для Д > 800 мм           поз. 4...6.


<table>
<colgroup><col width="6%"><col width="6%"><col width="11%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="13">Установка трубного пучка в корпус Слесарно-сборочные работы краном</td></tr>
<tr><td colspan="13">Карта 93, лист 1</td></tr>
<tr><td colspan="13">Содержание работы</td></tr>
<tr><td colspan="13">1. Подать трубный пучок к месту установки. Установка краном</td></tr>
<tr><td colspan="13">2. Нанести смазку на фланец, установить (рисунок прокладку. не приводится)</td></tr>
<tr><td colspan="13">3. Завести трубный пучок в корпус.</td></tr>
<tr><td colspan="13">4. Совместить отверстия фланца пучка с отверстиями фланца корпуса.</td></tr>
<tr><td colspan="13">5. Завести фиксирующие стержни.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3"></td><td>Длина пучка</td><td colspan="10">Диаметр пучка Д, мм, до</td></tr>
<tr><td rowspan="2">L, мм, до</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td><td>1200</td><td>1600</td><td>2000</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="5"></td><td>1000</td><td>6,4</td><td>7,7</td><td>9,0</td><td>10,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>2000</td><td>7,8</td><td>9,4</td><td>10,9</td><td>12,2</td><td>13,5</td><td>15,2</td><td>18,4</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>3000</td><td>8,7</td><td>10,5</td><td>12,2</td><td>13,7</td><td>15,2</td><td>17,0</td><td>20,6</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>4000</td><td>9,5</td><td>11,4</td><td>13,2</td><td>14,9</td><td>16,4</td><td>18,4</td><td>22,4</td><td>26,2</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>5000</td><td>10,1</td><td>12,2</td><td>14,1</td><td>15,8</td><td>17,5</td><td>19,6</td><td>23,8</td><td>27,9</td><td>36,0</td><td>43,0</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="6%"><col width="11%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="13">Установка трубного пучка в корпус Слесарно-сборочные работы краном</td></tr>
<tr><td colspan="13">Карта 93, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3"></td><td>Длина пучка</td><td colspan="10">Диаметр пучка Д, мм, до</td></tr>
<tr><td rowspan="2">L, мм, до</td><td>300</td><td>400</td><td>500</td><td>600</td><td>700</td><td>800</td><td>1000</td><td>1200</td><td>1600</td><td>2000</td></tr>
<tr><td colspan="10">Время Т, чел.-мин.</td></tr>
<tr><td>6</td><td></td><td>6000</td><td>10,6</td><td>12,8</td><td>14,8</td><td>16,7</td><td>18,4</td><td>20,6</td><td>25,0</td><td>29,0</td><td>38,0</td><td>46,0</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>


<a id="p105055"></a>*Примечание.* Работа выполняется бригадой из двух человек:

                  0,28    0,65
<a id="p105056"></a>    Т = 0,0228 х L     х Д          для Д <= 700 мм         поз. 1...6;

                   0,28    0,87
<a id="p105057"></a>    Т = 0,00538 х L     х Д         для Д > 700 мм          поз. 1...6.


<table>
<colgroup><col width="6%"><col width="11%"><col width="40%"><col width="3%"><col width="11%"><col width="15%"><col width="14%"></colgroup>
<tr><td colspan="4" rowspan="2">Установка лап или опор на корпус аппарата</td><td colspan="3">Слесарно-сборочные работы</td></tr>
<tr><td colspan="3">Карта 94, лист 1</td></tr>
<tr><td colspan="7">Вид А Вид Б Вид В Вид Г (рисунок (рисунок (рисунок (рисунок не приводится) не приводится) не приводится) не приводится)</td></tr>
<tr><td colspan="7">Вид Д Вид Е (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="7">Содержание работы</td></tr>
<tr><td colspan="7">1. Наметить место установки лапы или опоры на корпусе аппарата.</td></tr>
<tr><td colspan="7">2. Подать лапу или опору к месту сборки.</td></tr>
<tr><td colspan="7">3. Зачистить кромки и места установки под сварку.</td></tr>
<tr><td colspan="7">4. Выставить на корпус аппарата накладной лист, подогнать и прихватить электросваркой.</td></tr>
<tr><td colspan="7">5. Выставить лапу или опору на накладной лист и подогнать.</td></tr>
<tr><td colspan="7">6. Закрепить лапу или опору болтами или прихватить электросваркой, зачистить места прихваток.</td></tr>
<tr><td rowspan="6">N позиции</td><td>Масса лапы</td><td colspan="5">Лапы или опоры</td></tr>
<tr><td>или опоры</td><td>Для вертикальных емкостей</td><td colspan="4">Для горизонтальных емкостей</td></tr>
<tr><td rowspan="4">М, кг, до</td><td>Виды А, Б, В</td><td colspan="2">Вид Г</td><td>Вид Д</td><td>Вид Е</td></tr>
<tr><td colspan="5">Способ крепления</td></tr>
<tr><td>прихватка электросваркой</td><td colspan="4">болтами</td></tr>
<tr><td colspan="5">Время на лапу или опору Т, чел.-мин.</td></tr>
<tr><td>1</td><td>2</td><td>12,8</td><td colspan="2">-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>5</td><td>14,4</td><td colspan="2">-</td><td>-</td><td>-</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td>г</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="11%"><col width="40%"><col width="3%"><col width="11%"><col width="15%"><col width="14%"></colgroup>
<tr><td colspan="4" rowspan="2">Установка лап или опор на корпус аппарата</td><td colspan="3">Слесарно-сборочные работы</td></tr>
<tr><td colspan="3">Карта 94, лист 2</td></tr>
<tr><td rowspan="6">N позиции</td><td>Масса лапы</td><td colspan="5">Лапы или опоры</td></tr>
<tr><td>или опоры</td><td>Для вертикальных емкостей</td><td colspan="4">Для горизонтальных емкостей</td></tr>
<tr><td rowspan="4">М, кг, до</td><td>Виды А, Б, В</td><td colspan="2">Вид Г</td><td>Вид Д</td><td>Вид Е</td></tr>
<tr><td colspan="5">Способ крепления</td></tr>
<tr><td>прихватка электросваркой</td><td colspan="4">болтами</td></tr>
<tr><td colspan="5">Время на лапу или опору Т, чел.-мин.</td></tr>
<tr><td>3</td><td>10</td><td>15,9</td><td colspan="2">-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>25</td><td>18,1</td><td colspan="2">23,6</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>50</td><td>19,9</td><td colspan="2">25,9</td><td>26,9</td><td>-</td></tr>
<tr><td>6</td><td>75</td><td>21,1</td><td colspan="2">27,5</td><td>28,8</td><td>36,9</td></tr>
<tr><td>7</td><td>100</td><td>21,9</td><td colspan="2">28,6</td><td>30,2</td><td>38,3</td></tr>
<tr><td>8</td><td>200</td><td>24,2</td><td colspan="2">31,5</td><td>34,0</td><td>42,2</td></tr>
<tr><td>9</td><td>400</td><td>26,7</td><td colspan="2">34,8</td><td>38,2</td><td>46,5</td></tr>
<tr><td>10</td><td>600</td><td>28,2</td><td colspan="2">-</td><td>41,0</td><td>49,2</td></tr>
<tr><td>11</td><td>900</td><td>29,9</td><td colspan="2">-</td><td>-</td><td>52,1</td></tr>
<tr><td>12</td><td>1500</td><td>32,1</td><td colspan="2">-</td><td>-</td><td>55,9</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td>г</td></tr>
</table>


<a id="p105087"></a>Примечания:
1. <a id="p105088"></a>При измененных условиях установки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="22%"><col width="18%"><col width="26%"><col width="15%"><col width="18%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="2">Установка</td><td colspan="2">Наметка места установки</td></tr>
<tr><td>нормы времени</td><td>с накладным листом</td><td>без накладного листа</td><td>слесаремсборщиком</td><td>разметчиком</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>0,75</td><td>1,0</td><td>0,85</td></tr>
</table>



<a id="p105093"></a><a id="p105094"></a><a id="p105095"></a><a id="p105096"></a><a id="p105097"></a>

<table>
<colgroup><col width="60%"><col width="40%"></colgroup>
<tr><td rowspan="2">Установка лап или опор на корпус аппарата</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 94, лист 3</td></tr>
<tr><td>2. Работа выполняется бригадой из двух человек:</td><td></td></tr>
<tr><td>0,15 Т = 11,53 х М индекс а</td><td>поз. 1...12;</td></tr>
<tr><td>0,14 Т = 15,03 х М индекс б</td><td>поз. 4...9;</td></tr>
<tr><td>0,17 Т = 13,83 х М индекс в</td><td>поз. 5...10;</td></tr>
<tr><td>0,14 Т = 20,09 х М индекс г</td><td>поз. 6...12.</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="12%"><col width="20%"><col width="20%"><col width="20%"><col width="20%"></colgroup>
<tr><td colspan="4" rowspan="2">Установка планок, скоб и мелких деталей под сварку</td><td colspan="2">Слесарно-сборочные работы</td></tr>
<tr><td colspan="2">Карта 95, лист 1</td></tr>
<tr><td colspan="6">(рисунок не приводится)</td></tr>
<tr><td colspan="6">Содержание работы</td></tr>
<tr><td colspan="6">1. Взять деталь.</td></tr>
<tr><td colspan="6">2. Установить по месту.</td></tr>
<tr><td colspan="6">3. Прихватить деталь электросваркой.</td></tr>
<tr><td colspan="6">4. Зачистить места прихваток.</td></tr>
<tr><td rowspan="3">N позиции</td><td>Масса детали</td><td rowspan="3">Длина сопрягаемых кромок L, мм, до</td><td colspan="3">Толщина детали h, мм, до</td></tr>
<tr><td rowspan="2">М, кг, до</td><td>5</td><td>10</td><td>20</td></tr>
<tr><td colspan="3">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="7">4</td><td>100</td><td>0,6</td><td>0,7</td><td>0,8</td></tr>
<tr><td>2</td><td>150</td><td>0,7</td><td>0,8</td><td>0,9</td></tr>
<tr><td>3</td><td>230</td><td>0,8</td><td>0,9</td><td>1,0</td></tr>
<tr><td>4</td><td>350</td><td>0,9</td><td>1,1</td><td>1,3</td></tr>
<tr><td>5</td><td>500</td><td>1,1</td><td>1,2</td><td>1,4</td></tr>
<tr><td>6</td><td>700</td><td>1,2</td><td>1,4</td><td>-</td></tr>
<tr><td>7</td><td>1000</td><td>1,3</td><td>1,6</td><td>-</td></tr>
<tr><td>8</td><td rowspan="4">8</td><td>100</td><td>0,7</td><td>0,8</td><td>0,9</td></tr>
<tr><td>9</td><td>150</td><td>0,8</td><td>0,9</td><td>1,1</td></tr>
<tr><td>10</td><td>230</td><td>0,9</td><td>1,1</td><td>1,3</td></tr>
<tr><td>11</td><td>350</td><td>1,1</td><td>1,3</td><td>1,5</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="12%"><col width="20%"><col width="20%"><col width="20%"><col width="20%"></colgroup>
<tr><td colspan="4" rowspan="2">Установка планок, скоб и мелких деталей под сварку</td><td colspan="2">Слесарно-сборочные работы</td></tr>
<tr><td colspan="2">Карта 95, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Масса детали</td><td rowspan="3">Длина сопрягаемых кромок L, мм, до</td><td colspan="3">Толщина детали h, мм, до</td></tr>
<tr><td rowspan="2">М, кг, до</td><td>5</td><td>10</td><td>20</td></tr>
<tr><td colspan="3">Время Т, чел.-мин.</td></tr>
<tr><td>12</td><td rowspan="3">8</td><td>500</td><td>1,2</td><td>1,4</td><td>1,7</td></tr>
<tr><td>13</td><td>700</td><td>1,4</td><td>1,6</td><td>-</td></tr>
<tr><td>14</td><td>1000</td><td>1,6</td><td>1,8</td><td>-</td></tr>
<tr><td>15</td><td rowspan="7">16</td><td>100</td><td>0,8</td><td>1,0</td><td>1,1</td></tr>
<tr><td>16</td><td>150</td><td>1,0</td><td>1,1</td><td>1,3</td></tr>
<tr><td>17</td><td>230</td><td>1,1</td><td>1,3</td><td>1,5</td></tr>
<tr><td>18</td><td>350</td><td>1,3</td><td>1,5</td><td>1,7</td></tr>
<tr><td>19</td><td>500</td><td>1,5</td><td>1,7</td><td>-</td></tr>
<tr><td>20</td><td>700</td><td>1,6</td><td>1,9</td><td>-</td></tr>
<tr><td>21</td><td>1000</td><td>1,9</td><td>2,1</td><td>-</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td></tr>
</table>


<a id="p105133"></a>*Примечание.* Работа выполняется одним человеком:

                                   0,23    0,34    0,2
<a id="p105134"></a>                     Т = 0,0682 х М     х L     х h   .


<table>
<colgroup><col width="60%"><col width="40%"></colgroup>
<tr><td rowspan="2">Установка фирменных табличек</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 96, лист 1</td></tr>
<tr><td colspan="2">Вид А Вид Б</td></tr>
<tr><td colspan="2">(рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="2">Содержание работы</td></tr>
<tr><td colspan="2">Крепление винтами</td></tr>
<tr><td colspan="2">1. Взять инструмент.</td></tr>
<tr><td colspan="2">2. Взять табличку, установить по месту, наметить отверстия под винты, снять табличку.</td></tr>
<tr><td colspan="2">3. Просверлить отверстия под винты.</td></tr>
<tr><td colspan="2">4. Нарезать резьбу.</td></tr>
<tr><td colspan="2">5. Установить табличку по месту и прикрепить к изделию винтами.</td></tr>
<tr><td colspan="2">Крепление заклепками</td></tr>
<tr><td colspan="2">1. Взять инструмент.</td></tr>
<tr><td colspan="2">2. Взять табличку, установить на стальную пластинку, наметить отверстия под заклепки и снять табличку.</td></tr>
<tr><td colspan="2">3. Просверлить отверстия в пластинах под заклепки.</td></tr>
<tr><td colspan="2">4. Установить пластину в сборе по месту и прикрепить к изделию электроприхватками.</td></tr>
<tr><td colspan="2">5. Зачистить места прихваток от шлака и брызг.</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="20%"><col width="15%"><col width="18%"><col width="20%"><col width="20%"></colgroup>
<tr><td colspan="4" rowspan="2">Установка фирменных табличек</td><td colspan="2">Слесарно-сборочные работы</td></tr>
<tr><td colspan="2">Карта 96, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид крепления</td><td rowspan="3">Диаметр винта или заклепки, мм, до</td><td colspan="3">Кол-во винтов заклепок или прихваток</td></tr>
<tr><td>2</td><td>4</td><td>6</td></tr>
<tr><td colspan="3">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="2">Винтами (вид А)</td><td>3</td><td>6,0</td><td>10,8</td><td>15,6</td></tr>
<tr><td>2</td><td>6</td><td>5,3</td><td>9,5</td><td>13,7</td></tr>
<tr><td>3</td><td>Заклепками с последующей</td><td>3</td><td>3,1</td><td>4,3</td><td>5,5</td></tr>
<tr><td>4</td><td>электросваркой (вид Б)</td><td>6</td><td>3,4</td><td>4,9</td><td>6,4</td></tr>
<tr><td>5</td><td>Электросваркой</td><td>-</td><td>1,0</td><td>1,5</td><td>2,0</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td></tr>
</table>


<a id="p105160"></a>*Примечание.* Работа выполняется одним человеком.


<table>
<colgroup><col width="6%"><col width="14%"><col width="15%"><col width="9%"><col width="9%"><col width="6%"><col width="3%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="6" rowspan="2">Установка и крепление заглушек, штуцеров</td><td colspan="5">Слесарно-сборочные работы</td></tr>
<tr><td colspan="5">Карта 97, лист 1</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">1. Подать заглушку к месту сборки. (рисунок</td></tr>
<tr><td colspan="11">2. Установить прокладку на штуцер. не приводится)</td></tr>
<tr><td colspan="11">3. Заглушить штуцер.</td></tr>
<tr><td colspan="11">4. Вставить болты.</td></tr>
<tr><td colspan="11">5. Навернуть и затянуть гайки.</td></tr>
<tr><td rowspan="5">N позиции</td><td rowspan="5">Вид заглушки</td><td>Диаметр штуцера</td><td colspan="8">Диаметр болта d, мм</td></tr>
<tr><td rowspan="4">Д, мм, до</td><td colspan="2">до 16</td><td colspan="6">свыше 16</td></tr>
<tr><td colspan="8">Количество болтов n, шт., до</td></tr>
<tr><td>4</td><td>6</td><td colspan="2">8</td><td>12</td><td>16</td><td>20</td><td>24</td></tr>
<tr><td colspan="8">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="6">Постоянная</td><td>76</td><td>3,3</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>2</td><td>146</td><td>3,5</td><td>5,8</td><td colspan="2">9,0</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>3</td><td>219</td><td>3,7</td><td>6,1</td><td colspan="2">9,5</td><td>12,6</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>4</td><td>299</td><td>3,8</td><td>6,3</td><td colspan="2">9,9</td><td>13,3</td><td>16,3</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td>426</td><td>-</td><td>6,6</td><td colspan="2">11,1</td><td>14,8</td><td>18,3</td><td>21,4</td><td>-</td></tr>
<tr><td>6</td><td>600</td><td>-</td><td>6,9</td><td colspan="2">10,8</td><td>14,4</td><td>17,8</td><td>20,8</td><td>23,8</td></tr>
<tr><td>7</td><td rowspan="6">Временная</td><td>76</td><td>1,9</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>146</td><td>2,1</td><td>3,4</td><td colspan="2">5,4</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td>219</td><td>2,2</td><td>3,6</td><td colspan="2">5,7</td><td>7,6</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td>299</td><td>2,3</td><td>3,7</td><td colspan="2">5,9</td><td>7,9</td><td>9,8</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td>426</td><td>-</td><td>3,9</td><td colspan="2">6,2</td><td>8,3</td><td>10,2</td><td>11,9</td><td>-</td></tr>
<tr><td>12</td><td>600</td><td>-</td><td>4,0</td><td colspan="2">6,4</td><td>8,6</td><td>10,6</td><td>12,5</td><td>14,2</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td>г</td><td>д</td><td>е</td><td>ж</td></tr>
</table>


<a id="p105183"></a>Примечания:
1. <a id="p105184"></a>При снятии заглушек время по карте применяется с коэффициентом 0,6.


<a id="p105187"></a><a id="p105188"></a><a id="p105189"></a><a id="p105190"></a><a id="p105191"></a>

<table>
<colgroup><col width="60%"><col width="40%"></colgroup>
<tr><td rowspan="2">Установка и крепление заглушек, штуцеров</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 97, лист 2</td></tr>
<tr><td>2. Работа выполняется одним человеком:</td><td></td></tr>
<tr><td>0,12 0,72 Т = 0,715 х Д х n для d &lt;= 16</td><td>поз. 1...6;</td></tr>
<tr><td>0,12 0,72 Т = 1,12 х Д х n для d &gt; 16</td><td>поз. 1...6;</td></tr>
<tr><td>0,12 0,72 Т = 0,422 х Д х n для d &lt;= 16</td><td>поз. 7...12;</td></tr>
<tr><td>0,12 0,72 Т = 0,67 х Д х n для d &gt; 16</td><td>поз. 7...12.</td></tr>
</table>



#### <a id="p105192"></a>Раздел 5. ДИФФЕРЕНЦИРОВАННЫЕ НОРМАТИВЫ ШТУЧНОГО ВРЕМЕНИ НА СЛЕСАРНЫЕ И СЛЕСАРНО-СБОРОЧНЫЕ РАБОТЫ



<table>
<colgroup><col width="6%"><col width="14%"><col width="17%"><col width="23%"><col width="20%"><col width="20%"></colgroup>
<tr><td colspan="6">Прихватка деталей и узлов Слесарно-сборочные работы электросваркой</td></tr>
<tr><td colspan="6">Карта 98, лист 1</td></tr>
<tr><td colspan="6">Содержание работы</td></tr>
<tr><td colspan="6">1. Подвести электродержатель с электродом к месту прихватки.</td></tr>
<tr><td colspan="6">2. Возбудить дугу и прихватить детали.</td></tr>
<tr><td colspan="6">3. Отвести электродержатель.</td></tr>
<tr><td rowspan="5">N позиции</td><td rowspan="5">Толщина металла h, мм, до</td><td rowspan="5">Длина одной прихватки L, мм, до</td><td colspan="3">Марка электрода</td></tr>
<tr><td colspan="3">УОНИ-13, ОЗС-6, 7, 12</td></tr>
<tr><td colspan="3">Положение шва в пространстве</td></tr>
<tr><td>вертикальное, горизонтальное</td><td>потолочное</td><td>нижнее</td></tr>
<tr><td colspan="3">Время на одну прихватку Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="6">4</td><td>20</td><td>0,11</td><td>0,17</td><td>0,08</td></tr>
<tr><td>2</td><td>30</td><td>0,13</td><td>0,21</td><td>0,09</td></tr>
<tr><td>3</td><td>40</td><td>0,17</td><td>0,24</td><td>0,11</td></tr>
<tr><td>4</td><td>50</td><td>0,29</td><td>0,27</td><td>0,12</td></tr>
<tr><td>5</td><td>70</td><td>0,25</td><td>0,33</td><td>0,14</td></tr>
<tr><td>6</td><td>90</td><td>0,30</td><td>0,37</td><td>0,16</td></tr>
<tr><td>7</td><td rowspan="6">8</td><td>20</td><td>0,12</td><td>0,18</td><td>0,09</td></tr>
<tr><td>8</td><td>30</td><td>0,16</td><td>0,23</td><td>0,11</td></tr>
<tr><td>9</td><td>40</td><td>0,19</td><td>0,28</td><td>0,13</td></tr>
<tr><td>10</td><td>50</td><td>0,22</td><td>0,30</td><td>0,14</td></tr>
<tr><td>11</td><td>70</td><td>0,28</td><td>0,36</td><td>0,16</td></tr>
<tr><td>12</td><td>90</td><td>0,33</td><td>0,42</td><td>0,19</td></tr>
<tr><td>13</td><td rowspan="4">14</td><td>20</td><td>0,13</td><td>0,20</td><td>0,10</td></tr>
<tr><td>14</td><td>30</td><td>0,17</td><td>0,25</td><td>0,12</td></tr>
<tr><td>15</td><td>40</td><td>0,20</td><td>0,29</td><td>0,14</td></tr>
<tr><td>16</td><td>50</td><td>0,24</td><td>0,33</td><td>0,16</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="14%"><col width="17%"><col width="23%"><col width="20%"><col width="20%"></colgroup>
<tr><td colspan="6">Прихватка деталей и узлов Слесарно-сборочные работы электросваркой</td></tr>
<tr><td colspan="6">Карта 98, лист 2</td></tr>
<tr><td rowspan="5">N позиции</td><td rowspan="5">Толщина металла h, мм, до</td><td rowspan="5">Длина одной прихватки L, мм, до</td><td colspan="3">Марка электрода</td></tr>
<tr><td colspan="3">УОНИ-13, ОЗС-6, 7, 12</td></tr>
<tr><td colspan="3">Положение шва в пространстве</td></tr>
<tr><td>вертикальное, горизонтальное</td><td>потолочное</td><td>нижнее</td></tr>
<tr><td colspan="3">Время на одну прихватку Т, чел.-мин.</td></tr>
<tr><td>17</td><td rowspan="2">14</td><td>70</td><td>0,30</td><td>0,39</td><td>0,19</td></tr>
<tr><td>18</td><td>90</td><td>0,36</td><td>0,45</td><td>0,21</td></tr>
<tr><td>19</td><td rowspan="6">20</td><td>20</td><td>0,13</td><td>0,21</td><td>0,13</td></tr>
<tr><td>20</td><td>30</td><td>0,17</td><td>0,26</td><td>0,16</td></tr>
<tr><td>21</td><td>40</td><td>0,21</td><td>0,30</td><td>0,18</td></tr>
<tr><td>22</td><td>50</td><td>0,25</td><td>0,34</td><td>0,20</td></tr>
<tr><td>23</td><td>70</td><td>0,32</td><td>0,39</td><td>0,24</td></tr>
<tr><td>24</td><td>90</td><td>0,38</td><td>0,47</td><td>0,27</td></tr>
<tr><td>25</td><td rowspan="6">26</td><td>20</td><td>0,14</td><td>0,23</td><td>0,15</td></tr>
<tr><td>26</td><td>30</td><td>0,19</td><td>0,28</td><td>0,19</td></tr>
<tr><td>27</td><td>40</td><td>0,24</td><td>0,33</td><td>0,21</td></tr>
<tr><td>28</td><td>50</td><td>0,27</td><td>0,37</td><td>0,24</td></tr>
<tr><td>29</td><td>70</td><td>0,35</td><td>0,45</td><td>0,28</td></tr>
<tr><td>30</td><td>90</td><td>0,41</td><td>0,51</td><td>0,32</td></tr>
<tr><td>31</td><td rowspan="5">32</td><td>20</td><td>0,16</td><td>0,25</td><td>0,17</td></tr>
<tr><td>32</td><td>30</td><td>0,21</td><td>0,31</td><td>0,21</td></tr>
<tr><td>33</td><td>40</td><td>0,25</td><td>0,36</td><td>0,24</td></tr>
<tr><td>34</td><td>50</td><td>0,30</td><td>0,40</td><td>0,27</td></tr>
<tr><td>35</td><td>70</td><td>0,38</td><td>0,48</td><td>0,32</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td></tr>
</table>



<a id="p105242"></a><a id="p105243"></a><a id="p105244"></a><a id="p105245"></a><a id="p105246"></a><a id="p105247"></a><a id="p105248"></a>

<table>
<colgroup><col width="58%"><col width="42%"></colgroup>
<tr><td rowspan="2">Прихватка деталей и узлов электросваркой</td><td>Слесарно-сборочные работы</td></tr>
<tr><td>Карта 98, лист 3</td></tr>
<tr><td>Примечание. Работа выполняется одним человеком:</td><td></td></tr>
<tr><td>0,13 0,7</td><td></td></tr>
<tr><td>Т = 0,01095 х h х L</td><td>для h &lt;= 20 индекс а;</td></tr>
<tr><td>0,36 0,7</td><td></td></tr>
<tr><td>Т = 0,055 х h х L</td><td>для h &gt; 20</td></tr>
<tr><td>0,13 0,54</td><td></td></tr>
<tr><td>Т = 0,02785 х h х L</td><td>для h &lt;= 20 индекс б;</td></tr>
<tr><td>0,36 0,54</td><td></td></tr>
<tr><td>Т = 0,014 х h х L</td><td>для h &gt; 20</td></tr>
<tr><td>0,22 0,48</td><td></td></tr>
<tr><td>Т = 0,01355 х h х L</td><td>для h &lt;= 14 индекс в.</td></tr>
<tr><td>0,64 0,48</td><td></td></tr>
<tr><td>Т = 0,00452 х h х L</td><td>для h &gt; 14</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="12%"><col width="20%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="11">Установка и снятие струбцин Слесарно-сборочные работы</td></tr>
<tr><td colspan="11">Карта 99</td></tr>
<tr><td colspan="11">Содержание работы</td></tr>
<tr><td colspan="11">1. Взять струбцину. Вид А</td></tr>
<tr><td colspan="11">2. Установить на скрепляемые детали. (рисунок</td></tr>
<tr><td colspan="11">3. Ввернуть прижимной болт рукояткой не приводится) или гаечным ключом до упора.</td></tr>
<tr><td colspan="11">4. Отвернуть прижимной болт рукояткой Вид Б или гаечным ключом. (рисунок</td></tr>
<tr><td colspan="11">5. Снять струбцину, отложить. не приводится)</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид крепления</td><td rowspan="3">Наименование операции</td><td colspan="8">Диаметр болта Д, мм, до</td></tr>
<tr><td>12</td><td>16</td><td>20</td><td>24</td><td>30</td><td>36</td><td>42</td><td>48</td></tr>
<tr><td colspan="8">Время на струбцину Т, чел.-мин.</td></tr>
<tr><td>1</td><td>Гаечным ключом</td><td>Установка</td><td>0,20</td><td>0,25</td><td>0,29</td><td>0,32</td><td>0,38</td><td>0,43</td><td>0,47</td><td>0,52</td></tr>
<tr><td>2</td><td>(вид А)</td><td>Снятие</td><td>0,12</td><td>0,15</td><td>0,18</td><td>0,20</td><td>0,23</td><td>0,27</td><td>0,29</td><td>0,32</td></tr>
<tr><td>3</td><td>Рукояткой</td><td>Установка</td><td>0,17</td><td>0,21</td><td>0,26</td><td>0,28</td><td>0,33</td><td>0,38</td><td>0,42</td><td>0,46</td></tr>
<tr><td>4</td><td>(вид Б)</td><td>Снятие</td><td>0,10</td><td>0,13</td><td>0,16</td><td>0,18</td><td>0,20</td><td>0,23</td><td>0,26</td><td>0,29</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td></tr>
</table>


<a id="p105263"></a>*Примечание.* Работа выполняется одним человеком:

                                     0,7
<a id="p105264"></a>                       Т = 0,0351 х Д         поз. 1;

                                     0,7
<a id="p105265"></a>                       Т = 0,0211 х Д         поз. 2;

                                     0,7
<a id="p105266"></a>                       Т = 0,2985 х Д         поз. 3;

                                      0,7
<a id="p105267"></a>                       Т = 0,01756 х Д        поз. 4.


<table>
<colgroup><col width="5%"><col width="14%"><col width="18%"><col width="14%"><col width="9%"><col width="8%"><col width="8%"><col width="9%"><col width="15%"></colgroup>
<tr><td colspan="7" rowspan="2">Срубка сборочных планок, скоб, электроприхваток и зачистка мест прихваток</td><td colspan="2">Слесарные работы</td></tr>
<tr><td colspan="2">Карта 100, лист 1</td></tr>
<tr><td colspan="9">Содержание работы</td></tr>
<tr><td colspan="9">1. Взять инструмент.</td></tr>
<tr><td colspan="9">2. Срубить сборочные приспособления пневматическим зубилом после прихватки.</td></tr>
<tr><td colspan="9">3. Зачистить места прихваток наждачным кругом.</td></tr>
<tr><td colspan="9">4. Отложить инструмент.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Положение срубки, зачистки</td><td rowspan="3">Наименование приспособлений</td><td rowspan="3">Толщина металла, мм, до</td><td colspan="2" rowspan="3">Длина срубки, зачистки, мм, до</td><td colspan="3">Вид работы</td></tr>
<tr><td colspan="2">срубка</td><td>зачистка</td></tr>
<tr><td colspan="3">Время на одну штуку Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="12">Горизонтальное</td><td rowspan="2">-</td><td rowspan="2">-</td><td rowspan="2">Прихватки</td><td>35</td><td colspan="2">0,11</td><td>0,16</td></tr>
<tr><td>2</td><td>60</td><td colspan="2">0,18</td><td>0,28</td></tr>
<tr><td>3</td><td rowspan="6">Сборочные планки</td><td rowspan="3">5</td><td colspan="2">100</td><td colspan="2">0,27</td><td>0,44</td></tr>
<tr><td>4</td><td colspan="2">200</td><td colspan="2">0,50</td><td>0,80</td></tr>
<tr><td>5</td><td colspan="2">300</td><td colspan="2">0,70</td><td>1,10</td></tr>
<tr><td>6</td><td rowspan="3">10</td><td colspan="2">100</td><td colspan="2">0,40</td><td>0,44</td></tr>
<tr><td>7</td><td colspan="2">200</td><td colspan="2">0,75</td><td>0,80</td></tr>
<tr><td>8</td><td colspan="2">300</td><td colspan="2">1,10</td><td>1,16</td></tr>
<tr><td>9</td><td rowspan="4">Скобы</td><td rowspan="2">5</td><td colspan="2">100</td><td colspan="2">0,36</td><td>0,60</td></tr>
<tr><td>10</td><td colspan="2">150</td><td colspan="2">0,49</td><td>0,90</td></tr>
<tr><td>11</td><td rowspan="2">10</td><td colspan="2">100</td><td colspan="2">0,49</td><td>0,60</td></tr>
<tr><td>12</td><td colspan="2">150</td><td colspan="2">0,70</td><td>0,90</td></tr>
<tr><td colspan="6">Индекс</td><td colspan="2">а</td><td>б</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="14%"><col width="18%"><col width="14%"><col width="9%"><col width="8%"><col width="8%"><col width="9%"><col width="15%"></colgroup>
<tr><td colspan="7" rowspan="2">Срубка сборочных планок, скоб, электроприхваток и зачистка мест прихваток</td><td colspan="2">Слесарные работы</td></tr>
<tr><td colspan="2">Карта 100, лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Положение срубки, зачистки</td><td rowspan="3">Наименование приспособлений</td><td rowspan="3">Толщина металла, мм, до</td><td colspan="2" rowspan="3">Длина срубки, зачистки</td><td colspan="3">Вид работы</td></tr>
<tr><td colspan="2">срубка</td><td>зачистка</td></tr>
<tr><td colspan="3">Время на одну штуку Т, чел.-мин.</td></tr>
<tr><td>13</td><td rowspan="12">Вертикальное</td><td rowspan="2">-</td><td rowspan="2">-</td><td rowspan="2">Прихватки</td><td>35</td><td colspan="2">0,13</td><td>0,18</td></tr>
<tr><td>14</td><td>60</td><td colspan="2">0,20</td><td>0,30</td></tr>
<tr><td>15</td><td rowspan="6">Сборочные планки</td><td rowspan="3">5</td><td colspan="2">100</td><td colspan="2">0,30</td><td>0,49</td></tr>
<tr><td>16</td><td colspan="2">200</td><td colspan="2">0,55</td><td>0,90</td></tr>
<tr><td>17</td><td colspan="2">300</td><td colspan="2">0,75</td><td>1,25</td></tr>
<tr><td>18</td><td rowspan="3">10</td><td colspan="2">100</td><td colspan="2">0,42</td><td>0,49</td></tr>
<tr><td>19</td><td colspan="2">200</td><td colspan="2">0,80</td><td>0,90</td></tr>
<tr><td>20</td><td colspan="2">300</td><td colspan="2">1,20</td><td>1,25</td></tr>
<tr><td>21</td><td rowspan="4">Скобы</td><td rowspan="2">5</td><td colspan="2">100</td><td colspan="2">0,40</td><td>0,70</td></tr>
<tr><td>22</td><td colspan="2">150</td><td colspan="2">0,55</td><td>1,00</td></tr>
<tr><td>23</td><td rowspan="2">10</td><td colspan="2">100</td><td colspan="2">0,55</td><td>0,70</td></tr>
<tr><td>24</td><td colspan="2">150</td><td colspan="2">0,80</td><td>1,00</td></tr>
<tr><td colspan="6">Индекс</td><td colspan="2">а</td><td>б</td></tr>
</table>


<a id="p105305"></a>Примечания:
1. <a id="p105306"></a>При измененных условиях срубки и зачистки в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="22%"><col width="20%"><col width="20%"><col width="15%"><col width="23%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="2">Материал</td><td colspan="2">Зачистка мест прихваток</td></tr>
<tr><td>нормы времени</td><td>углеродистая сталь</td><td>легированная сталь</td><td>наждачным кругом</td><td>пневматическим зубилом</td></tr>
<tr><td>Коэффициент</td><td>1,0</td><td>1,2</td><td>1,0</td><td>0,7</td></tr>
</table>


2. <a id="p105309"></a>Работа выполняется одним человеком:


<table>
<colgroup><col width="5%"><col width="19%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="10" rowspan="2">Снятие заусенцев в отверстиях после сверления</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 101</td></tr>
<tr><td colspan="14">Содержание работы 1. Взять инструмент.</td></tr>
<tr><td colspan="14">2. Снять заусенцы.</td></tr>
<tr><td colspan="14">3. Отложить инструмент.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Наименование инструмента</td><td colspan="12">Диаметр отверстия d, мм, до</td></tr>
<tr><td>8</td><td>12</td><td>16</td><td>20</td><td>25</td><td>30</td><td>35</td><td colspan="2">40</td><td>57</td><td>89</td><td>108</td></tr>
<tr><td colspan="12">Время на одно отверстие Т, чел.-мин.</td></tr>
<tr><td>1</td><td>Напильник</td><td>0,09</td><td>0,10</td><td>0,11</td><td>0,12</td><td>0,13</td><td>0,14</td><td>0,15</td><td colspan="2">0,16</td><td>0,19</td><td>0,21</td><td>0,23</td></tr>
<tr><td>2</td><td>Шабер</td><td>0,13</td><td>0,14</td><td>0,15</td><td>0,16</td><td>0,17</td><td>0,18</td><td>0,20</td><td colspan="2">0,22</td><td>0,26</td><td>0,29</td><td>0,32</td></tr>
<tr><td>3</td><td>Пневмомашина с наждачным кругом</td><td>0,06</td><td>0,07</td><td>0,08</td><td>0,09</td><td>0,10</td><td>0,11</td><td>0,12</td><td colspan="2">0,13</td><td>0,15</td><td>0,17</td><td>0,19</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td></tr>
</table>


<a id="p105321"></a>Примечания:
1. <a id="p105322"></a>При измененных условиях обработки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="16%"><col width="18%"><col width="18%"><col width="11%"><col width="11%"><col width="11%"><col width="8%"><col width="8%"></colgroup>
<tr><td>Факторы, влияющие на изменение</td><td colspan="3">Материал</td><td colspan="2">Число отверстий в детали</td><td colspan="2">Толщина металла, мм</td></tr>
<tr><td>нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>до 5</td><td>св. 5</td><td>до 6</td><td>св. 6</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>1,0</td><td>0,9</td><td>1,0</td><td>1,1</td></tr>
</table>


2. <a id="p105325"></a>Работа выполняется одним человеком:

                                     0,37
<a id="p105326"></a>                       Т = 0,0398 х d         поз. 1;

                                    0,37
<a id="p105327"></a>                       Т = 0,054 х d          поз. 2;

                                     0,48
<a id="p105328"></a>                       Т = 0,0215 х d         поз. 3.


<table>
<colgroup><col width="3%"><col width="8%"><col width="8%"><col width="11%"><col width="8%"><col width="8%"><col width="7%"><col width="8%"><col width="8%"><col width="8%"><col width="10%"><col width="16%"></colgroup>
<tr><td colspan="11" rowspan="2">Зачистка кромок под сварку</td><td>Слесарные работы</td></tr>
<tr><td>Карта 102, лист 1</td></tr>
<tr><td colspan="12">Вид А Вид Б Вид В (рисунок не приводится) (рисунок не приводится) (рисунок не приводится)</td></tr>
<tr><td colspan="12">Содержание работы</td></tr>
<tr><td colspan="12">1. Взять инструмент.</td></tr>
<tr><td colspan="12">2. Зачистить кромки под сварку.</td></tr>
<tr><td colspan="12">3. Отложить инструмент.</td></tr>
<tr><td rowspan="7">N позиции</td><td rowspan="7">Характер зачистки</td><td>Толщина листа h,</td><td colspan="8">Инструмент</td><td rowspan="7">Ручная стальная щетка</td></tr>
<tr><td rowspan="6">мм, до</td><td colspan="4">Пневматическая машинка с наждачным кругом (после резки на гильотинных ножницах)</td><td colspan="4">Пневматическое зубило (после машинной газовой резки)</td></tr>
<tr><td colspan="8">Вид контура кромки</td></tr>
<tr><td colspan="2">прямолинейный</td><td colspan="2">криволинейный</td><td colspan="2">прямолинейный</td><td colspan="2">криволинейный</td></tr>
<tr><td colspan="8">Положение зачищаемой кромки</td></tr>
<tr><td>горизонтальное</td><td>вертикальное</td><td>горизонтальное</td><td>вертикальное</td><td>горизонтальное</td><td>вертикальное</td><td>горизонтальное</td><td>вертикальное</td></tr>
<tr><td colspan="8">Время на 1 м стыка Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="9">Односторонняя (вид А)</td><td>4</td><td>0,50</td><td>0,60</td><td>0,60</td><td>0,65</td><td>0,65</td><td>0,78</td><td>0,78</td><td>0,94</td><td>0,24</td></tr>
<tr><td>2</td><td>6</td><td>0,60</td><td>0,72</td><td>0,72</td><td>0,78</td><td>0,78</td><td>0,93</td><td>0,93</td><td>1,15</td><td>0,26</td></tr>
<tr><td>3</td><td>10</td><td>0,74</td><td>0,89</td><td>0,89</td><td>0,99</td><td>0,99</td><td>1,15</td><td>1,15</td><td>1,40</td><td>0,30</td></tr>
<tr><td>4</td><td>14</td><td>0,87</td><td>1,0</td><td>1,0</td><td>1,15</td><td>1,15</td><td>1,35</td><td>1,35</td><td>1,65</td><td>0,33</td></tr>
<tr><td>5</td><td>20</td><td>1,0</td><td>1,2</td><td>1,2</td><td>1,35</td><td>1,35</td><td>1,60</td><td>1,60</td><td>1,95</td><td>0,37</td></tr>
<tr><td>6</td><td>30</td><td>1,20</td><td>1,4</td><td>1,4</td><td>1,60</td><td>1,60</td><td>1,90</td><td>1,90</td><td>2,35</td><td>0,41</td></tr>
<tr><td>7</td><td>50</td><td>1,5</td><td>1,75</td><td>1,75</td><td>2,0</td><td>2,0</td><td>2,4</td><td>2,4</td><td>2,95</td><td>0,47</td></tr>
<tr><td>8</td><td>80</td><td>1,8</td><td>2,15</td><td>2,15</td><td>2,5</td><td>2,5</td><td>3,0</td><td>3,0</td><td>3,65</td><td>0,70</td></tr>
<tr><td>9</td><td>100</td><td>2,1</td><td>2,5</td><td>2,5</td><td>2,9</td><td>2,9</td><td>3,5</td><td>3,5</td><td>4,2</td><td>0,93</td></tr>
<tr><td colspan="3">Формулы расчета</td><td>Т = 0,2758 х 0,43 h</td><td colspan="2">0,43 Т = 0,331 х h</td><td colspan="2">0,45 Т = 0,35 х h</td><td colspan="2">0,45 Т = 0,416 х h</td><td>Т = 0,506 х 0,45 h</td><td>0,27 Т = 0,163 х h для h &lt;= 50 0,88 Т = 0,0148 х h для h св. 50</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="8%"><col width="8%"><col width="10%"><col width="8%"><col width="8%"><col width="7%"><col width="8%"><col width="8%"><col width="8%"><col width="10%"><col width="16%"></colgroup>
<tr><td colspan="11" rowspan="2">Зачистка кромок под сварку</td><td>Слесарные работы</td></tr>
<tr><td>Карта 102, лист 2</td></tr>
<tr><td rowspan="7">N позиции</td><td rowspan="7">Характер зачистки</td><td>Толщина листа h,</td><td colspan="8">Инструмент</td><td rowspan="7">Ручная стальная щетка</td></tr>
<tr><td rowspan="6">мм, до</td><td colspan="4">Пневматическая машинка с наждачным кругом (после резки на гильотинных ножницах)</td><td colspan="4">Пневматическое зубило (после машинной газовой резки)</td></tr>
<tr><td colspan="8">Вид контура кромки</td></tr>
<tr><td colspan="2">прямолинейный</td><td colspan="2">криволинейный</td><td colspan="2">прямолинейный</td><td colspan="2">криволинейный</td></tr>
<tr><td colspan="8">Положение зачищаемой кромки</td></tr>
<tr><td>горизонтальное</td><td>вертикальное</td><td>горизонтальное</td><td>вертикальное</td><td>горизонтальное</td><td>вертикальное</td><td>горизонтальное</td><td>вертикальное</td></tr>
<tr><td colspan="8">Время на 1 м стыка Т, чел.-мин.</td></tr>
<tr><td>10</td><td rowspan="9">Четырехсторонняя (вид Б)</td><td>4</td><td>0,78</td><td>0,94</td><td>0,94</td><td>1,05</td><td>1,05</td><td>1,25</td><td>1,25</td><td>1,50</td><td>0,38</td></tr>
<tr><td>11</td><td>6</td><td>0,93</td><td>1,15</td><td>1,15</td><td>1,30</td><td>1,30</td><td>1,50</td><td>1,50</td><td>1,80</td><td>0,43</td></tr>
<tr><td>12</td><td>10</td><td>1,15</td><td>1,40</td><td>1,40</td><td>1,60</td><td>1,60</td><td>1,90</td><td>1,90</td><td>2,25</td><td>0,49</td></tr>
<tr><td>13</td><td>14</td><td>1,35</td><td>1,65</td><td>1,65</td><td>1,85</td><td>1,85</td><td>2,20</td><td>2,20</td><td>2,60</td><td>0,54</td></tr>
<tr><td>14</td><td>20</td><td>1,60</td><td>1,95</td><td>1,95</td><td>2,15</td><td>2,15</td><td>2,60</td><td>2,60</td><td>3,10</td><td>0,59</td></tr>
<tr><td>15</td><td>30</td><td>1,90</td><td>2,35</td><td>2,35</td><td>2,55</td><td>2,55</td><td>3,10</td><td>3,10</td><td>3,70</td><td>0,66</td></tr>
<tr><td>16</td><td>50</td><td>2,40</td><td>2,95</td><td>2,95</td><td>3,20</td><td>3,20</td><td>3,90</td><td>3,90</td><td>4,70</td><td>0,76</td></tr>
<tr><td>17</td><td>80</td><td>3,00</td><td>3,65</td><td>3,65</td><td>3,90</td><td>3,90</td><td>4,85</td><td>4,85</td><td>5,80</td><td>1,15</td></tr>
<tr><td>18</td><td>100</td><td>3,50</td><td>4,20</td><td>4,20</td><td>4,50</td><td>4,50</td><td>5,60</td><td>5,60</td><td>6,70</td><td>1,50</td></tr>
<tr><td colspan="3">Формулы расчета</td><td>Т = 0,416 х 0,45 h</td><td colspan="2">0,45 Т = 0,506 х h</td><td colspan="2">0,43 Т = 0,593 х h</td><td colspan="2">0,45 Т = 0,675 х h</td><td>Т = 0,805 х 0,45 h</td><td>0,27 Т = 0,264 х h для h &lt;= 50 мм 0,88 Т = 0,024 х h для h св. 50 мм</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p105362"></a>Примечания:
1. <a id="p105363"></a>При измененных условиях зачистки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="10%"><col width="9%"><col width="11%"><col width="12%"><col width="23%"><col width="19%"><col width="3%"><col width="13%"></colgroup>
<tr><td colspan="6" rowspan="2">Зачистка кромок под сварку</td><td colspan="2">Слесарные работы</td></tr>
<tr><td colspan="2">Карта 102, лист 3</td></tr>
<tr><td>Факторы, влияющие на</td><td colspan="2">Материал</td><td colspan="5">Зачистка кромок односторонняя</td></tr>
<tr><td>изменение норм времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>двухсторонняя (вид В)</td><td>после ручной газовой резки (к зачистке пневматическим зубилом)</td><td colspan="2">пневматической машинкой с наждачным кругом (после резки на гильотинных ножницах)</td><td>пневматическим зубилом (после машинной газовой резки)</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>1,8</td><td>1,4</td><td colspan="2">1,0</td><td>1,0</td></tr>
</table>


2. <a id="p105368"></a>Работа выполняется одним человеком.


<table>
<colgroup><col width="5%"><col width="15%"><col width="10%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="2%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="12" rowspan="2">Зачистка сварных швов</td><td colspan="4">Слесарные работы</td></tr>
<tr><td colspan="4">Карта 103, лист 1</td></tr>
<tr><td colspan="16">Содержание работы</td></tr>
<tr><td colspan="16">1. Взять инструмент.</td></tr>
<tr><td colspan="16">2. Зачистить шов.</td></tr>
<tr><td colspan="16">3. Отложить инструмент.</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Инструмент</td><td rowspan="3">Тип шва</td><td colspan="13">Длина шва L, мм, до</td></tr>
<tr><td>100</td><td>200</td><td>250</td><td>320</td><td>400</td><td>600</td><td>630</td><td>800</td><td colspan="2">1000</td><td>1250</td><td>1600</td><td>2000</td></tr>
<tr><td colspan="13">Время Т, чел.-мин.</td></tr>
<tr><td>1</td><td rowspan="2">Пневматическое зубило</td><td>стыковой</td><td>0,34</td><td>0,49</td><td>0,56</td><td>0,63</td><td>0,71</td><td>0,87</td><td>1,07</td><td>1,34</td><td colspan="2">1,62</td><td>1,98</td><td>2,48</td><td>3,03</td></tr>
<tr><td>2</td><td>угловой</td><td>0,37</td><td>0,57</td><td>0,65</td><td>0,76</td><td>0,85</td><td>1,04</td><td>1,28</td><td>1,59</td><td colspan="2">1,94</td><td>2,37</td><td>2,96</td><td>3,62</td></tr>
<tr><td>3</td><td>Пневматическая машинка</td><td>стыковой</td><td>0,51</td><td>0,83</td><td>0,97</td><td>1,15</td><td>1,29</td><td>1,54</td><td>1,86</td><td>2,25</td><td colspan="2">2,69</td><td>3,21</td><td>3,91</td><td>4,68</td></tr>
<tr><td>4</td><td>с наждачным кругом</td><td>угловой</td><td>0,63</td><td>1,02</td><td>1,20</td><td>1,42</td><td>1,62</td><td>1,98</td><td>2,44</td><td>3,02</td><td colspan="2">3,69</td><td>4,51</td><td>5,64</td><td>6,89</td></tr>
<tr><td>5</td><td rowspan="2">Стальная щетка</td><td>стыковой</td><td>0,07</td><td>0,10</td><td>0,11</td><td>0,13</td><td>0,15</td><td>0,18</td><td>0,21</td><td>0,25</td><td colspan="2">0,29</td><td>0,34</td><td>0,41</td><td>0,47</td></tr>
<tr><td>6</td><td>угловой</td><td>0,12</td><td>0,18</td><td>0,20</td><td>0,23</td><td>0,26</td><td>0,31</td><td>0,36</td><td>0,43</td><td colspan="2">0,50</td><td>0,59</td><td>0,70</td><td>0,81</td></tr>
<tr><td>7</td><td rowspan="2">Зубило и молоток</td><td>стыковой</td><td>0,60</td><td>0,97</td><td>1,15</td><td>1,35</td><td>1,65</td><td>2,0</td><td>2,45</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>угловой</td><td>0,73</td><td>1,15</td><td>1,40</td><td>1,65</td><td>1,95</td><td>2,40</td><td>2,95</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="79%"><col width="21%"></colgroup>
<tr><td rowspan="2">Зачистка сварных швов</td><td>Слесарные работы</td></tr>
<tr><td>Карта 103, лист 2</td></tr>
</table>


<a id="p105387"></a>Примечания:
1. <a id="p105388"></a>При измененных условиях зачистки приведенное в нормативной карте время применяется с коэффициентами:


<table>
<colgroup><col width="11%"><col width="6%"><col width="5%"><col width="5%"><col width="8%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td>Факторы, влияющие на</td><td colspan="3">Материал</td><td colspan="10">Зачистка швов</td></tr>
<tr><td>изменение нормы времени</td><td>легированная сталь</td><td>углеродистая сталь</td><td>цветные сплавы</td><td>от брызг наплавленного металла</td><td>прямолинейных</td><td>криволинейных</td><td>заподлицо с деталью</td><td>с катетом до 10</td><td>с катетом св. 10</td><td>в горизонтальном положении</td><td>в вертикальном положении</td><td>в потолочном положении</td><td>в труднодоступных местах</td></tr>
<tr><td>Коэффициент</td><td>1,2</td><td>1,0</td><td>0,8</td><td>0,4</td><td>1,0</td><td>1,3</td><td>1,5</td><td>1,0</td><td>1,2</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,8</td></tr>
</table>


2. <a id="p105391"></a>Работа выполняется одним человеком:

              0,54                                           0,54
<a id="p105392"></a>Т = 0,0282 х L      поз. 1  для L <= 320 мм;  Т = 0,00592 х L      поз. 5  для L <= 320 мм;

               0,9                                           0,7
<a id="p105393"></a>Т = 0,00324 х L     поз. 1  для L > 320 мм;   Т = 0,00232 х L      поз. 5  для L > 320 мм;

              0,62                                           0,54
<a id="p105394"></a>Т = 0,0213 х L      поз. 2  для L <= 320 мм;  Т = 0,01015 х L      поз. 6  для L <= 320 мм;

               0,9                                           0,7
<a id="p105395"></a>Т = 0,00387 х L     поз. 2  для L > 320 мм;   Т = 0,00398 х L      поз. 6  для L > 320 мм;

              0,7                                          0,7
<a id="p105396"></a>Т = 0,0203 х L      поз. 3  для L <= 320 мм;  Т = 0,024 х L        поз. 7  для L <= 320 мм;

              0,8                                            0,9
<a id="p105397"></a>Т = 0,0107 х L      поз. 3  для L > 320 мм;   Т = 0,00744 х L      поз. 7  для L > 320 мм;

              0,7                                           0,7
<a id="p105398"></a>Т = 0,0251 х L      поз. 4  для L <= 320 мм;  Т = 0,0290 х L       поз. 8  для L <= 320 мм;

               0,9                                           0,9
<a id="p105399"></a>Т = 0,00737 х L     поз. 4  для L > 320 мм;   Т = 0,00899 х L      поз. 8  для L > 320 мм.



<a id="p105400"></a>

---