---
title: "Постановление Минтруда России от 12.02.2004 N 14"
number: "14"
issuer: "Министерство труда и социального развития Российской Федерации"
issued_on: 2004-02-12
status: действует
canonical: "https://bukva.ai/docs/postanovlenie-14-2004-mintrud-rossii-ministerstvo"
---

## Постановление Минтруда России от 12.02.2004 N 14

# Постановление Минтруда России от 12.02.2004 N 14

"Об утверждении Межотраслевых укрупненных нормативов времени на работы, выполняемые на отделочно-расточных станках (единичное и мелкосерийное производство)"

> [!IMPORTANT]
> В соответствии с Трудовым кодексом РФ системы нормирования труда определяются работодателем с учетом мнения представительного органа работников или устанавливаются коллективным договором. Для однородных работ могут разрабатываться и устанавливаться типовые (межотраслевые, отраслевые, профессиональные и иные) нормы труда в соответствии с Правилами, утвержденными Постановлением Правительства РФ от 11.11.2002 N 804.


<a id="p101274"></a>**МИНИСТЕРСТВО ТРУДА И СОЦИАЛЬНОГО РАЗВИТИЯ**
**РОССИЙСКОЙ ФЕДЕРАЦИИ**


## <a id="p101275"></a>ПОСТАНОВЛЕНИЕ

от 12 февраля 2004 г. N 14

<a id="p101276"></a>**ОБ УТВЕРЖДЕНИИ МЕЖОТРАСЛЕВЫХ УКРУПНЕННЫХ НОРМАТИВОВ**
**ВРЕМЕНИ НА РАБОТЫ, ВЫПОЛНЯЕМЫЕ НА ОТДЕЛОЧНО-РАСТОЧНЫХ**
**СТАНКАХ (ЕДИНИЧНОЕ И МЕЛКОСЕРИЙНОЕ ПРОИЗВОДСТВО)**

<a id="p101277"></a>Министерство труда и социального развития Российской Федерации постановляет:
1. <a id="p101278"></a>Утвердить Межотраслевые укрупненные [нормативы](#p100002) времени на работы, выполняемые на отделочно-расточных станках (единичное и мелкосерийное производство), разработанные Управлением нормативов по труду Научно-исследовательского института труда и социального страхования Министерства труда и социального развития Российской Федерации.
2. <a id="p101279"></a>Установить, что утвержденные настоящим Постановлением Межотраслевые укрупненные нормативы времени рекомендуются для расчета норм времени на работы, выполняемые на отделочно-расточных станках в условиях единичного и мелкосерийного типов производств в машиностроительных и металлообрабатывающих организациях независимо от форм собственности и организационно-правовых форм.

<a id="p101280"></a>Министр труда
и социального развития
Российской Федерации
**А.ПОЧИНОК**





<a id="p100001"></a>Утверждены
Постановлением
Министерства труда
и социального развития
Российской Федерации
от 12 февраля 2004 г. N 14


## <a id="p100002"></a>МЕЖОТРАСЛЕВЫЕ УКРУПНЕННЫЕ НОРМАТИВЫ ВРЕМЕНИ НА РАБОТЫ, ВЫПОЛНЯЕМЫЕ НА ОТДЕЛОЧНО-РАСТОЧНЫХ СТАНКАХ (ЕДИНИЧНОЕ И МЕЛКОСЕРИЙНОЕ ПРОИЗВОДСТВО)


<a id="p100003"></a>Межотраслевые укрупненные нормативы времени на работы, выполняемые на отделочно-расточных станках (единичное и мелкосерийное производство), утверждены Постановлением Министерства труда и социального развития Российской Федерации от 12 февраля 2004 г. N 14.
<a id="p100004"></a>Нормативы времени разработаны Управлением нормативов по труду ФГУП "НИИ труда и социального страхования" Министерства труда и социального развития Российской Федерации с учетом мнения Федерации Независимых Профсоюзов России и Российского Союза промышленников и предпринимателей.
<a id="p100005"></a>Нормативами охвачены работы по растачиванию отверстий на отделочно-расточных станках в деталях из чугуна, стали, бронзы, латуни, алюминиевых сплавов и других материалов резцами с пластинами из твердых и сверхтвердых сплавов и материалов. Сборник содержит нормативные карты подготовительно-заключительного времени на партию деталей, вспомогательного времени на установку и снятие детали, неполного штучного времени на обработку отверстий. В [Приложениях](#p101139) к сборнику приведены рекомендуемые режимы резания, положенные в основу расчета неполного штучного времени, рекомендации по выбору диаметров консольной части борштанг.
<a id="p100006"></a>Укрупненные нормативы времени рекомендуются для расчета норм времени на работы, выполняемые на отделочно-расточных станках в условиях единичного и мелкосерийного типов производства в машиностроительных и металлообрабатывающих организациях независимо от форм собственности и организационно-правовых форм.
<a id="p100007"></a>Межотраслевые укрупненные нормативы времени на работы, выполняемые на отделочно-расточных станках (единичное и мелкосерийное производство) разработаны коллективом авторов в составе: к.э.н. Н.А. Софинского, к.э.н. Р.П. Миусковой, к.э.н. В.С. Суворова, Л.А. Филипповой, И.В. Ильина, З.Д. Соколовой, А.М. Комарова.


### 1. <a id="p100008"></a>ОБЩАЯ ЧАСТЬ


<a id="p100009"></a>1.1. Межотраслевые укрупненные нормативы времени на работы, выполняемые на отделочно-расточных станках (единичное и мелкосерийное производство) (далее - Нормативы времени), предназначены для нормирования отделочно-расточных работ, выполняемых в машиностроительных и металлообрабатывающих организациях независимо от организационно-правовых форм, ведомственной принадлежности и форм собственности.
<a id="p100010"></a>1.2. Нормативные карты содержат подготовительно-заключительное время, вспомогательное время на установку и снятие детали, укрупненные нормативы неполного штучного времени на рабочий ход при растачивании отверстий и подрезании торцов для различных типов отделочно-расточных головок: АР-0, АР-1, АР-2, АР-3, АР-4.
<a id="p100011"></a>Укрупненными нормативами неполного штучного времени предусмотрена обработка деталей из чугуна серого, ковкого, высокопрочного, термообработанного и отбеленного; стали качественной низкоуглеродистой, легированной, конструктивной, высоколегированной и труднообрабатываемой, термообработанной; бронзы, латуни, алюминиевых сплавов, металлокерамики и твердого сплава.
<a id="p100012"></a>Предусмотрено применение инструментов с пластинами из твердых - ВК3М (ВК3, ВК60М), Т30К4 и сверхтвердых материалов - Композит 01 (Эльбор-Р), Композит 10 (Гексанит-Р), Исмит, синтетический и натуральный алмаз.

#### <a id="p100013"></a>1.3 В основу разработки Нормативов времени положены следующие материалы:

<a id="p100014"></a>карты технологических процессов, режимов резания, применяемых на предприятиях, хронометражные наблюдения по затратам времени на операцию;
<a id="p100015"></a>нормативы режимов резания и геометрия резцов для тонкого растачивания, обработки на отделочно-расточных станках;
<a id="p100016"></a>паспортные данные отделочно-расточных станков;
<a id="p100017"></a>результаты анализа трудового процесса, рациональных методов труда и организации рабочих мест;
<a id="p100018"></a>действующие ГОСТы;
<a id="p100019"></a>Рекомендации по организации работы службы охраны труда в организации, утвержденные Постановлением Минтруда России от 8 февраля 2000 г. N 4;
<a id="p100020"></a>Федеральный закон "Об основах охраны труда в Российской Федерации" (Собрание законодательства Российской Федерации, 1999, N 29, ст. 3702).
<a id="p100021"></a>Единичное и мелкосерийное производство характеризуются широкой номенклатурой изготавливаемых изделий и малым объемом их выпуска. Работа производится мелкими партиями, технологическая документация оформляется, в основном, в виде маршрутных и маршрутно-операционных карт.
<a id="p100022"></a>Заточка инструмента производится централизованно, а получение и доставка инструмента на рабочее место осуществляются заточником.
<a id="p100023"></a>Заготовки на рабочее место доставляются подсобными рабочими.
<a id="p100024"></a>Наряды на работу, технологическую документацию получает расточник.
<a id="p100025"></a>Тип производства в соответствии с ГОСТ 14.004-83 характеризуется коэффициентом закрепления операций (Кз.о). Коэффициент закрепления операций (Кз.о) определяется как отношение всех различных технологических операций, выполненных или подлежащих выполнению в течение месяца, к числу рабочих мест. Для мелкосерийного производства: 20 < Кз.о <= 40, при единичном типе производства величина Кз.о не регламентируется.

#### <a id="p100026"></a>1.4 Норма времени на выполнение станочной операции (Нвр) определяется по формуле:


<a id="p100027"></a> $\text{Н}_{\text{вр}} = \text{Т}_{\text{ш}} + \frac{t_{\text{пз}}}{q} ,\text{мин }.,$ (1)

<a id="p100028"></a>где:
<a id="p100029"></a>Тш - норма штучного времени, мин.;
<a id="p100030"></a>tпз - подготовительно-заключительное время, мин.;
<a id="p100031"></a>q - число деталей в партии.
<a id="p100032"></a>Норма штучного времени определяется суммированием времени на установку и снятие детали и неполного штучного времени на рабочий ход по формуле:

<a id="p100033"></a>Тш = [tву + (tнш1 + tнш2) x Ку] x Ктш, мин., (2)

<a id="p100034"></a>где:
<a id="p100035"></a>tву - норматив вспомогательного времени на установку и снятие детали, мин.;
<a id="p100036"></a>tнш1, tнш2 - неполное штучное время на рабочий ход, мин.;
<a id="p100037"></a>Ку - поправочный коэффициент на неполное штучное время в зависимости от измененных условий работы;
<a id="p100038"></a>Ктш - коэффициент к норме штучного времени в зависимости от числа деталей в партии.
<a id="p100039"></a>Расчет норм времени производится по предварительно разработанному маршрутному или маршрутно-операционному технологическому процессу с указанием в нем обрабатываемых поверхностей, их размеров и характера обработки.
<a id="p100040"></a>При повторном рабочем ходе к неполному штучному времени прибавляется время на установку резца нового размера tвр, приведенное в таблице 1.1.

<a id="p100041"></a>Таблица 1.1

<a id="p100042"></a>**ВСПОМОГАТЕЛЬНОЕ ВРЕМЯ НА УСТАНОВКУ РЕЗЦА НА РАЗМЕР**


| <a id="p100043"></a>Группа станков с диаметром растачивания, мм, до | Время, мин. |
| --- | --- |
| <a id="p100044"></a>125 | 0,4 |
| <a id="p100045"></a>400 | 0,6 |


<a id="p100046"></a>В этом случае штучное время определяется по формуле:

<a id="p100047"></a>Тш = [tву + (tнш1 + tнш2) x Ку + tвр] x Ктш, мин. (3)

<a id="p100048"></a>Неполное штучное время в нормативных картах определялось по формуле:

<a id="p100049"></a> $t_{\text{нш}} = (t_{\text{о}} + t_{\text{пер}}) \times (1 + \frac{\text{а}_{\text{орг}} + \text{а}_{\text{тех}} + \text{а}_{\text{отл}}}{100}),\text{мин }.,$ (4)

<a id="p100050"></a>где:
<a id="p100051"></a>tо - основное технологическое время, мин.;
<a id="p100052"></a>tпер - вспомогательное время, связанное с технологическим переходом, мин.;
<a id="p100053"></a>аорг, атех, аотл - время на организационное, техническое обслуживание рабочего места, отдых и лечебные потребности в % к оперативному времени.
<a id="p100054"></a>Основное технологическое время - (tо) определялось на компьютере по режимам резания в расчете на группу аналогичного по виду оборудования, обрабатываемого материала и материала режущего инструмента по формуле:

<a id="p100055"></a> $t_{\text{о}} = \frac{L + l_{1} + l_{2}}{n_{\text{шп}} \times S_{\text{о}}} ,\text{мин }.,$ 

<a id="p100056"></a>где:
<a id="p100057"></a>L - длина обрабатываемой поверхности, мм (определяется по чертежу);
<a id="p100058"></a>l1 + l2 - величина врезания и перебега, мм;
<a id="p100059"></a>nшп - частота вращения шпинделя, об./мин.;
<a id="p100060"></a>Sо - подача на 1 оборот шпинделя, мм/об.

##### <a id="p100061"></a>1.4.1 Нормативы подготовительно-заключительного времени предусматривают выполнение следующих работ:

- <a id="p100062"></a>получение наряда, технологической документации;
- <a id="p100063"></a>ознакомление с работой, чертежом и получение инструктажа;
- <a id="p100064"></a>получение недостающих на рабочем месте инструментов и приспособлений, необходимых для обработки данной партии деталей;
- <a id="p100065"></a>подготовку рабочего места, наладку и переналадку оборудования, инструментов и приспособлений;
- <a id="p100066"></a>установку и снятие инструментов и приспособлений по окончании обработки партии деталей и другие подготовительно-заключительные работы, связанные с изготовлением данной партии деталей.
<a id="p100067"></a>Нормативы подготовительно-заключительного времени приведены в виде укрупненных комплексов приемов работы. В картах даны также нормативы времени на выполнение дополнительных приемов подготовительно-заключительной работы, которые могут иметь место.
<a id="p100068"></a>Подготовительно-заключительное время приведено в зависимости от вида обработки, числа режущих инструментов в наладке и определяется как сумма величин времени, затрачиваемых на подготовку станка к работе.
<a id="p100069"></a>При бригадной форме организации труда, когда проводится межсменная передача обрабатываемых деталей, размер подготовительно-заключительного времени может быть уменьшен по сравнению с нормативным на 30 - 50%.
<a id="p100070"></a>1.4.2. Нормативами вспомогательного времени на установку и снятие детали предусмотрены все типовые способы установки, выверки и крепления детали в специальных нормализованных и универсальных приспособлениях или непосредственно на столе станочника.
<a id="p100071"></a>Время на установку и снятие детали приведено укрупненно на технологические комплексы приемов. В состав комплексов включены следующие основные приемы:
- <a id="p100072"></a>установить деталь;
- <a id="p100073"></a>выверить и закрепить ее;
- <a id="p100074"></a>включить и выключить вращение шпинделя;
- <a id="p100075"></a>открепить деталь;
- <a id="p100076"></a>снять ее со станка;
- <a id="p100077"></a>транспортировать деталь на место складирования;
- <a id="p100078"></a>очистить приспособление от стружки.
<a id="p100079"></a>Кроме перечисленных в состав комплексов включены также приемы, выполняемые при работе с мостовым краном, - вызвать кран, застропить, транспортировать деталь к станку и отстропить деталь.
<a id="p100080"></a>Установка и снятие детали массой до 20 кг производятся вручную, а свыше 20 кг с помощью подъемно-транспортного оборудования. В нормативах предусматривается применение двух видов подъемно-транспортного оборудования: мостового крана и подъемника при станке или группе станков. В нормативной карте дано время на работу с мостовым краном, которое учитывает время на вызов крана в размере 1,5 мин. При работе с подъемником это время необходимо вычитать.
<a id="p100081"></a>В целях упрощения расчетов время на установку и снятие детали рассчитано с учетом времени на обслуживание рабочего места, отдых и личные потребности.
<a id="p100082"></a>1.4.3. Нормативное время (техническое и организационное) на обслуживание рабочего места, отдых и личные потребности включено также в неполное штучное время в соответствии с данными табл. 1.2.

<a id="p100083"></a>Таблица 1.2

<a id="p100084"></a>**ВРЕМЯ НА ОБСЛУЖИВАНИЕ РАБОЧЕГО МЕСТА,**
**ОТДЫХ И ЛИЧНЫЕ ПОТРЕБНОСТИ**


| <a id="p100085"></a>Группа станков с диаметром растачивания, мм, до | Время, % |
| --- | --- |
| <a id="p100086"></a>125 | 10 |
| <a id="p100087"></a>400 | 12 |


<a id="p100088"></a>Техническое обслуживание рабочих мест предусматривает выполнение следующих работ:
- <a id="p100089"></a>периодическую правку инструмента и замену его вследствие затупления;
- <a id="p100090"></a>регулировку и подналадку станка в процессе работы.
<a id="p100091"></a>Организационное обслуживание предусматривает уход за рабочим местом, относящийся к рабочей смене, и включает выполнение следующих работ:
- <a id="p100092"></a>осмотр и опробование работы оборудования;
- <a id="p100093"></a>раскладывание инструмента в начале и уборку его в конце смены;
- <a id="p100094"></a>смазку и чистку станка в течение рабочего дня;
- <a id="p100095"></a>получение инструмента в течение рабочего дня;
- <a id="p100096"></a>уборку рабочего места в течение смены;
- <a id="p100097"></a>сбор стружки и отходов в зоне рабочих мест.

##### <a id="p100098"></a>1.4.4 Нормативы неполного штучного времени включают:

- <a id="p100099"></a>основное (технологическое) время;
- <a id="p100100"></a>вспомогательное время, связанное с переходом, операцией;
- <a id="p100101"></a>время на обслуживание рабочего места, перерывы на отдых и личные потребности.
<a id="p100102"></a>Нормативы неполного штучного времени (tнш) рассчитаны на рациональные организационно-технические условия, соответствующие мелкосерийному производству.
<a id="p100103"></a>При уменьшении или увеличении партии обрабатываемых деталей к норме штучного времени следует применять поправочные коэффициенты, приведенные в [карте 2](#p100189).
<a id="p100104"></a>Основное время tо рассчитано исходя из применения оптимального сочетания факторов обработки (глубины резания t, подачи Sо, скорости резания V и стойкости режущего инструмента Т) с учетом системы СПИД "станок-приспособление, инструмент, деталь", а также других факторов. В целях удобства пользования нормативами неполного штучного времени и сокращения затрат на его определение величина врезания и перебега режущего инструмента учтена в картах неполного штучного времени (через основное время). Исходя из этого, в зависимости от длины обрабатываемой поверхности tнш определяется непосредственно по размерам обрабатываемой поверхности, указанным в чертеже детали.
<a id="p100105"></a>Вспомогательное время, связанное с переходом и принятое при расчете неполного штучного времени, содержит следующие приемы:
- <a id="p100106"></a>включение и выключение оборотов шпинделя или подачи;
- <a id="p100107"></a>подвод и отвод инструмента;
- <a id="p100108"></a>перемещение детали из зоны резания;
- <a id="p100109"></a>контрольные измерения.
<a id="p100110"></a>Неполное штучное время на растачивание отверстий и подрезание торцов в нормативах дано на один рабочий ход в зависимости от диаметра обрабатываемого отверстия и длины обработки, на подрезание торца в зависимости от диаметра обрабатываемого отверстия.
<a id="p100111"></a>Для отличающихся от принятых при расчете нормативов технологических условий в картах неполного штучного времени приводятся поправочные коэффициенты на измененные условия работы (Ку).
<a id="p100112"></a>Приведенные в [Приложении 1](#p101139) сборника режимы резания следует рассматривать как справочный материал, который можно использовать для инструктажа рабочих станочников.
<a id="p100113"></a>В свою очередь, вспомогательное время, связанное с переходом, приведено в [Приложении 2](#p101197) и может использоваться так же, как справочный материал.
<a id="p100114"></a>1.5. При установлении на предприятиях норм времени на основе настоящего сборника тарификация работ и профессий должна производиться по Единому тарифно-квалификационному справочнику работ и профессий рабочих. Выпуск 2, раздел "Механическая обработка металлов и других материалов", утвержденному Постановлением Министерства труда и социального развития Российской Федерации от 15 ноября 1999 г. N 45.
<a id="p100115"></a>Квалификация рабочего, не соответствующая установленному разряду работы, не может служить основанием для каких-либо изменений норм времени, рассчитанных по сборнику.

#### <a id="p100116"></a>1.6 Пример расчета нормы времени.



<table>
<colgroup><col width="28%"><col width="5%"><col width="36%"><col width="9%"><col width="8%"><col width="14%"></colgroup>
<tr><td rowspan="10"><a id="p100117"></a>Содержание операции: растачивание отверстий Ø 125Н7 и 200Н7<br><img src="https://i.bukva.ai/p31QqdK8k/img_0.png" alt="1. Общая часть"><br>Исходные данные:<br>Станок алмазно-расточной, модель 2714<br>Отделочно-расточная головка АР-4<br>Обрабатываемая деталь - корпус<br>Припуск на сторону - 0,1 мм<br>Материал обрабатываемой детали - чугун СЧ21 224...264 НВ<br>Способ крепления - на столе с домкратом и с креплением болтами и планками, с выверкой в двух плоскостях<br>Масса детали - 103 кг<br>Меритель - универсальный<br>Количество деталей в партии - 6</td><td>N поз.</td><td>Определение элементов нормы времени</td><td>Обозначение</td><td>Время, мин.</td><td>Обоснование</td></tr>
<tr><td><a id="p100118"></a>1</td><td>Установить и снять деталь</td><td>tву</td><td>22,4</td><td>Карта 3 (<a href="#p100206">поз. 9</a>, инд. К)</td></tr>
<tr><td rowspan="4"><a id="p100119"></a>2</td><td>Неполное штучное время:</td><td></td><td></td><td rowspan="2">Карта 4 (<a href="#p100230">поз. 9</a>, инд. И, Ку = 1)</td></tr>
<tr><td>Расточить отверстие Ø 125Н7, L120, окончательно</td><td>tнш1</td><td>9,55</td></tr>
<tr><td>Расточить отверстие Ø 200Н7, L290, окончательно</td><td rowspan="2">tнш2</td><td rowspan="2">30,6</td><td rowspan="2">Карта 4 (<a href="#p100250">поз. 11</a>, инд. О, Ку = 1)</td></tr>
<tr><td>Тнш = tнш1 + tнш2 = 9,55 + 30,6 = 40,15</td></tr>
<tr><td rowspan="2"><a id="p100120"></a>3</td><td>Штучное время</td><td>Ктш = 0,95</td><td rowspan="2">59,42</td><td rowspan="2">Карта 2 <a href="#p100194">(поз. 4)</a></td></tr>
<tr><td>Тш = (tву + Тнш) x Ктш = (22,4 + 40,15) x 0,95 = 59,42</td><td>Тш</td></tr>
<tr><td><a id="p100121"></a>4</td><td>Подготовительно-заключительное время</td><td>tпз</td><td>23</td><td>Карта 1 (<a href="#p100175">поз. 1</a>, инд. Г)</td></tr>
<tr><td><a id="p100122"></a>5</td><td>Норма времени<br>$\text{Н}_{\text{вр}} = \text{Т}_{\text{ш}} + \frac{t_{\text{пз}}}{n} = 59,42 + \frac{23}{6} = 63,25$</td><td>Нвр</td><td>63,25</td><td></td></tr>
</table>



### 2. <a id="p100125"></a>ХАРАКТЕРИСТИКА ПРИМЕНЯЕМОГО ОБОРУДОВАНИЯ И ТЕХНОЛОГИЯ РАБОТЫ


<a id="p100126"></a>2.1. Нормативы времени и режимов резания на работы, выполняемые на отделочно-расточных станках, приведенные в сборнике, рассчитаны на наиболее распространенное на машиностроительных предприятиях отделочно-расточное оборудование отечественного производства.
<a id="p100127"></a>Краткие технические характеристики станков и их паспортные данные представлены в табл. 2.1.

<a id="p100128"></a>Таблица 2.1

<a id="p100129"></a>**КРАТКИЕ ТЕХНИЧЕСКИЕ ХАРАКТЕРИСТИКИ**
**ОТДЕЛОЧНО-РАСТОЧНЫХ СТАНКОВ**


<table>
<colgroup><col width="11%"><col width="16%"><col width="12%"><col width="8%"><col width="10%"><col width="10%"><col width="10%"><col width="10%"><col width="13%"></colgroup>
<tr><td rowspan="5"><a id="p100130"></a>Модель</td><td rowspan="5">Рабочая поверхность стола, мм</td><td rowspan="5">Пределы подач стола, мм/мин.</td><td colspan="5">Типы головок</td><td rowspan="5">Мощность двигателя, кВт</td></tr>
<tr><td>АР-0</td><td>АР-1</td><td>АР-2</td><td>АР-3</td><td>АР-4</td></tr>
<tr><td colspan="5">Условные диаметры растачиваемых отверстий, мм</td></tr>
<tr><td>6 - 12</td><td>8 - 32</td><td>20 - 63</td><td>50 - 125</td><td>100 - 400</td></tr>
<tr><td colspan="5">Максимально допустимое число оборотов шпинделя</td></tr>
<tr><td><a id="p100131"></a>2705П/В</td><td>320 x 500</td><td>10 - 500</td><td rowspan="8">10000</td><td rowspan="8">5000/4000</td><td rowspan="8">3150/2500</td><td rowspan="8">2000/1600</td><td rowspan="8">1250/1000</td><td rowspan="6">1,5 - 5</td></tr>
<tr><td><a id="p100132"></a>2706П/В</td><td>320 x 500</td><td>8 - 500</td></tr>
<tr><td><a id="p100133"></a>2711П/В</td><td>500 x 710</td><td>5 - 800</td></tr>
<tr><td><a id="p100134"></a>2712П/В</td><td>500 x 710</td><td>8 - 800</td></tr>
<tr><td><a id="p100135"></a>2713П/В</td><td>800 x 1000</td><td rowspan="2">8 - 400</td></tr>
<tr><td><a id="p100136"></a>2714П/В</td><td>800 x 1000</td></tr>
<tr><td><a id="p100137"></a>2777П/В</td><td>800 x 1400</td><td rowspan="2">6 - 500</td><td>1,5 - 12</td></tr>
<tr><td><a id="p100138"></a>2779П/В</td><td>1250 x 1250</td><td>1,6 - 5,5</td></tr>
<tr><td><a id="p100139"></a>2Е78ПН</td><td>500 x 1250</td><td>0,025 - 0,2 &lt;*&gt;</td><td colspan="5">1200</td><td>2,2</td></tr>
</table>



<a id="p100140"></a>

---

<a id="p100141"></a><*> Рабочая подача шпиндельной бабки, мм/мин.

<a id="p100142"></a>*Примечание.* Перечисленные выше отделочно-расточные полуавтоматы являются базовыми моделями специальных полуавтоматов.

<a id="p100143"></a>2.2. Нормативы режимов резания в зависимости от обрабатываемого материала (его твердости, шероховатости обрабатываемой поверхности) и материала режущего инструмента приведены в [Приложении 1](#p101139).
<a id="p100144"></a>2.3. Растачивание отверстий, как наиболее распространенная операция, выполняемая на отделочно-расточных станках, характеризуется небольшим сечением среза и обеспечивает точное расположение осей растачиваемых отверстий, высокую диаметральную точность (0,015 - 0,030 мм) и шероховатость обрабатываемой поверхности:
- <a id="p100145"></a>Ra 2,5...0,20 - для стальных деталей;
- <a id="p100146"></a>Ra 2,5...0,40 - для чугунных и 2,0...0,10 - для деталей из цветных сплавов.
<a id="p100147"></a>2.4. Необходимыми условиями применения рекомендуемых режимов резания являются исправность станка и соответствие техническим характеристикам по точности.

#### <a id="p100148"></a>2.5 Технологические схемы обработки. Растачивание гладких отверстий.



<table>
<colgroup><col width="17%"><col width="17%"><col width="33%"><col width="33%"></colgroup>
<tr><td colspan="2"><a id="p100149"></a>Короткое сквозное отверстие<br>Длинное сквозное или соосные отверстия</td><td rowspan="2"><img src="https://i.bukva.ai/p31QqdK8k/img_1.png" alt="2. Характеристика применяемого оборудования и технология работы"><br>Рис. 1</td><td rowspan="2">Снятие всего припуска однорезцовой борштангой за один рабочий ход</td></tr>
<tr><td colspan="2"><a id="p100150"></a>Короткое глухое отверстие<br>Длинное глухое отверстие</td></tr>
<tr><td colspan="2"><a id="p100151"></a>Короткое сквозное отверстие<br>Длинное сквозное или соосные отверстия</td><td rowspan="2"><img src="https://i.bukva.ai/p31QqdK8k/img_2.png" alt="2. Характеристика применяемого оборудования и технология работы"><br>Рис. 2</td><td>Снятие всего припуска двумя однорезцовыми борштангами за два рабочих хода</td></tr>
<tr><td colspan="2"><a id="p100152"></a>Короткое глухое отверстие<br>Длинное глухое отверстие</td><td>Обработка глухих отверстий за два рабочих хода осуществляется за счет передвижки обрабатываемой заготовки с повторением рабочего цикла</td></tr>
<tr><td colspan="2"><a id="p100153"></a>Короткое сквозное отверстие</td><td><img src="https://i.bukva.ai/p31QqdK8k/img_3.png" alt="2. Характеристика применяемого оборудования и технология работы"><br>Рис. 3</td><td>Снятие всего припуска одной борштангой с двумя последовательно расположенными резцами за один рабочий ход</td></tr>
<tr><td colspan="2"><a id="p100154"></a>Длинное сквозное отверстие</td><td rowspan="2"><img src="https://i.bukva.ai/p31QqdK8k/img_4.png" alt="2. Характеристика применяемого оборудования и технология работы"><br>Рис. 4</td><td rowspan="2">Снятие всего припуска одной борштангой с двумя одновременно работающими резцами за один рабочий ход</td></tr>
<tr><td colspan="2"><a id="p100155"></a>Короткое глухое отверстие<br>Длинное глухое отверстие</td></tr>
<tr><td><a id="p100156"></a>Растачивание ступенчатых отверстий</td><td>Сквозное ступенчатое отверстие</td><td><img src="https://i.bukva.ai/p31QqdK8k/img_5.png" alt="2. Характеристика применяемого оборудования и технология работы"><br>Рис. 5</td><td>Снятие всего припуска на каждой ступени одним резцом при последовательной работе резцов</td></tr>
<tr><td><a id="p100157"></a>Подрезание торцовых поверхностей</td><td>Торец, подрезаемый широколезвийным резцом</td><td><img src="https://i.bukva.ai/p31QqdK8k/img_6.png" alt="2. Характеристика применяемого оборудования и технология работы"><br>Рис. 6</td><td>Снятие припуска с торцовой поверхности заготовки методом осевой подачи инструмента</td></tr>
</table>



### 3. <a id="p100158"></a>ОРГАНИЗАЦИОННО-ТЕХНИЧЕСКИЕ УСЛОВИЯ И ОРГАНИЗАЦИЯ ТРУДА


<a id="p100159"></a>3.1. Мелкосерийное производство характеризуется широкой номенклатурой изготавливаемых деталей и малым объемом выпуска продукции, отсутствием закрепления детали за определенным станком.
<a id="p100160"></a>Обработка выполняется на основании маршрутной или маршрутно-операционной технологии и преимущественно с применением универсальных, нормализованных и специальных приспособлений и инструментов.
<a id="p100161"></a>Наряды на работу, технологическую документацию, приспособления и инструмент получает и доставляет на рабочее место токарь-расточник.
<a id="p100162"></a>Заготовки на рабочее место доставляются подсобными рабочими.
<a id="p100163"></a>Инструмент затачивается централизованно, периодическую правку производит токарь-расточник.
<a id="p100164"></a>3.2. В механических цехах мелкосерийного производства на рабочем месте токаря-расточника хранится необходимое количество инструментов и приспособлений.
<a id="p100165"></a>Для их хранения используется организационно-техническая оснастка, в которую входят: инструментальная тумбочка с планшетом (инструкция по технике безопасности), приемный столик, на верхней полке которого устанавливают тару с заготовками и деталями, а на нижней хранят приспособления и принадлежности; решетка для ног.
<a id="p100166"></a>При односменной работе на рабочем месте устанавливается тумбочка с одним отделением, при работе в две смены - с двумя отделениями, при трехсменной работе - две инструментальные тумбочки: одна с двумя отделениями, другая с одним. При обработке крупногабаритных и тяжелых заготовок на рабочем месте устанавливают механизированное подъемно-транспортное устройство (подвесная кран-балка с дистанционным вызовом или консольно-поворотный кран, установленный непосредственно у станка и обслуживающий один или два станка).
<a id="p100167"></a>*Примечание.* Приведенные в сборнике Нормативы времени на выполнение технологических операций рассчитаны на характерную для мелкосерийного производства организацию труда и рабочих мест.

#### <a id="p100168"></a>3.3 Организация рабочего места токаря-станочника.


<a id="p100169"></a> ![3. Организационно-технические условия и организация труда](https://i.bukva.ai/p31QqdK8k/img_7.png) 

<a id="p100170"></a>1 - шкаф инструментальный; 2 - столик приемный подвижный; 3 - стеллаж-подставка; 4 - стул подъемно-поваротный; 5 - планшет для чертежей; 6 - решетка под ноги рабочему; 7 - комплексный гидропривод


### 4. <a id="p100171"></a>НОРМАТИВНАЯ ЧАСТЬ



<table>
<colgroup><col width="6%"><col width="14%"><col width="9%"><col width="9%"><col width="5%"><col width="9%"><col width="10%"><col width="9%"><col width="5%"><col width="4%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="8"><a id="p100172"></a>Подготовительно-заключительное время</td><td colspan="4">Карта 1</td></tr>
<tr><td colspan="12"><a id="p100173"></a>1. На наладку станка, инструмента, приспособления</td></tr>
<tr><td rowspan="5"><a id="p100174"></a>N позиции</td><td rowspan="5">Вид обработки</td><td colspan="3" rowspan="5">Число режущих инструментов в наладке</td><td colspan="5">С заменой специального зажимного приспособления</td><td colspan="2" rowspan="2">Без замены специального зажимного приспособления</td></tr>
<tr><td colspan="2">вручную</td><td colspan="3">подъемником</td></tr>
<tr><td colspan="7">Группа станков с диаметром растачивания, мм, до</td></tr>
<tr><td>125</td><td>400</td><td>125</td><td colspan="2">400</td><td>125</td><td>400</td></tr>
<tr><td colspan="7">Время, мин.</td></tr>
<tr><td><a id="p100175"></a>1</td><td rowspan="8">Растачивание и подрезание торцов</td><td colspan="2" rowspan="4">Без установки приспособлений для подрезки торцов</td><td>2</td><td>17</td><td>20</td><td>21</td><td colspan="2">23</td><td>9</td><td>10</td></tr>
<tr><td><a id="p100176"></a>2</td><td>4</td><td>18</td><td>21</td><td>22</td><td colspan="2">25</td><td>10</td><td>12</td></tr>
<tr><td><a id="p100177"></a>3</td><td>6</td><td>21</td><td>25</td><td>25</td><td colspan="2">28</td><td>13</td><td>15</td></tr>
<tr><td><a id="p100178"></a>4</td><td>8</td><td>23</td><td>27</td><td>27</td><td colspan="2">31</td><td>16</td><td>18</td></tr>
<tr><td><a id="p100179"></a>5</td><td colspan="2" rowspan="4">С установкой приспособлений для подрезки торцов</td><td>2</td><td>28</td><td>31</td><td>32</td><td colspan="2">34</td><td>20</td><td>21</td></tr>
<tr><td><a id="p100180"></a>6</td><td>4</td><td>29</td><td>32</td><td>33</td><td colspan="2">36</td><td>21</td><td>23</td></tr>
<tr><td><a id="p100181"></a>7</td><td>6</td><td>32</td><td>36</td><td>36</td><td colspan="2">39</td><td>24</td><td>26</td></tr>
<tr><td><a id="p100182"></a>8</td><td>8</td><td>34</td><td>38</td><td>38</td><td colspan="2">42</td><td>27</td><td>29</td></tr>
<tr><td colspan="5"><a id="p100183"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td></tr>
<tr><td colspan="12"><a id="p100184"></a>2. Добавлять ко времени на наладку станка</td></tr>
<tr><td colspan="3" rowspan="2"><a id="p100185"></a>Элементы работы при наладке</td><td colspan="3" rowspan="2">Способ установки</td><td colspan="6">Группа станков с диаметром растачивания, мм, до</td></tr>
<tr><td colspan="3">125</td><td colspan="3">400</td></tr>
<tr><td rowspan="2"><a id="p100186"></a>9</td><td colspan="2" rowspan="3">Установить и снять отделочно-расточную головку</td><td colspan="3" rowspan="2">Вручную</td><td colspan="6">Время, мин.</td></tr>
<tr><td colspan="3">35</td><td colspan="3">45</td></tr>
<tr><td><a id="p100187"></a>10</td><td colspan="3">Подъемником</td><td colspan="3">40</td><td colspan="3">50</td></tr>
<tr><td><a id="p100188"></a>11</td><td colspan="5">Установить и отрегулировать один упор хода стола</td><td colspan="3">1</td><td colspan="3">1,3</td></tr>
</table>



<table>
<colgroup><col width="13%"><col width="14%"><col width="11%"><col width="11%"><col width="11%"><col width="12%"><col width="14%"><col width="16%"></colgroup>
<tr><td colspan="6"><a id="p100189"></a>Поправочные коэффициенты на штучное время в зависимости от количества обрабатываемых деталей в партии</td><td colspan="2">Карта 2</td></tr>
<tr><td rowspan="3"><a id="p100190"></a>N позиции</td><td rowspan="3">Штучное время Тш, мин., до</td><td colspan="6">Число деталей в партии, шт.</td></tr>
<tr><td>1 - 3</td><td>4 - 6</td><td>7 - 10</td><td>11 - 15</td><td>16 - 20</td><td>св. 20</td></tr>
<tr><td colspan="6">Значение коэффициента Ктш</td></tr>
<tr><td><a id="p100191"></a>1</td><td>3</td><td>1,2</td><td>1,1</td><td>1,05</td><td>1</td><td>0,95</td><td>0,9</td></tr>
<tr><td><a id="p100192"></a>2</td><td>15</td><td>1,1</td><td>1,05</td><td>1</td><td>0,95</td><td>0,9</td><td>0,85</td></tr>
<tr><td><a id="p100193"></a>3</td><td>60</td><td>1,05</td><td>1</td><td>0,95</td><td>0,9</td><td>0,85</td><td>0,8</td></tr>
<tr><td><a id="p100194"></a>4</td><td>Свыше 60</td><td>1</td><td>0,95</td><td>0,9</td><td>0,85</td><td>0,8</td><td>0,75</td></tr>
</table>


<a id="p100195"></a>*Примечание.* Число деталей устанавливается по согласованию с плановыми органами завода, как средняя величина для всех запусков изделий в производство в течение длительного времени (как правило, не менее года).


<table>
<colgroup><col width="5%"><col width="13%"><col width="11%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="12" rowspan="2"><a id="p100196"></a>Вспомогательное время на установку и снятие деталей (с учетом времени на обслуживание рабочего места, отдых и личные потребности)</td><td colspan="4">Карта 3</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="4"><a id="p100197"></a>N позиции</td><td rowspan="4">Способ установки и крепления детали</td><td rowspan="4">Характер выверки</td><td rowspan="4">Точность выверки на 1 п/м, мм, до</td><td colspan="7">Вручную</td><td colspan="5">Мостовым краном</td></tr>
<tr><td colspan="12">Масса детали m, кг, до</td></tr>
<tr><td>1</td><td>2</td><td>5</td><td>8</td><td>12</td><td>20</td><td>30</td><td>30</td><td>80</td><td>200</td><td>300</td><td>600</td></tr>
<tr><td colspan="12">Время tву, мин.</td></tr>
<tr><td><a id="p100198"></a>1</td><td rowspan="4">На столе с креплением болтами и планками</td><td rowspan="2">С выверкой в одной плоскости</td><td>0,3</td><td>1,9</td><td>2,2</td><td>2,5</td><td>2,7</td><td>3,1</td><td>3,8</td><td>4,4</td><td>6,7</td><td>9,1</td><td>12,3</td><td>12,6</td><td>-</td></tr>
<tr><td><a id="p100199"></a>2</td><td>0,1</td><td>2,1</td><td>2,5</td><td>2,7</td><td>3,1</td><td>3,6</td><td>4,1</td><td>4,7</td><td>8,1</td><td>10</td><td>13,4</td><td>13,7</td><td>16,6</td></tr>
<tr><td><a id="p100200"></a>3</td><td rowspan="2">С выверкой в двух плоскостях</td><td>0,3</td><td>2,6</td><td>3</td><td>3,6</td><td>4,1</td><td>4,6</td><td>5,2</td><td>5,8</td><td>12,3</td><td>13,8</td><td>18,5</td><td>18,8</td><td>20,7</td></tr>
<tr><td><a id="p100201"></a>4</td><td>0,1</td><td>3,1</td><td>3,6</td><td>4,1</td><td>4,5</td><td>4,8</td><td>5,6</td><td>6,2</td><td>13,4</td><td>15,1</td><td>20,1</td><td>20,4</td><td>23,9</td></tr>
<tr><td><a id="p100202"></a>5</td><td rowspan="6">На столе с домкратом и подставками (или угольником) с креплением болтами и планками</td><td rowspan="3">С выверкой в одной плоскости</td><td>0,3</td><td>2,7</td><td>3,2</td><td>3,4</td><td>3,8</td><td>4,2</td><td>4,9</td><td>5,5</td><td>9,3</td><td>10,6</td><td>15,1</td><td>15,4</td><td>18,3</td></tr>
<tr><td><a id="p100203"></a>6</td><td>0,1</td><td>2,8</td><td>3,4</td><td>3,6</td><td>4,1</td><td>4,7</td><td>5,3</td><td>5,9</td><td>10,3</td><td>11,8</td><td>16,8</td><td>17,2</td><td>20,6</td></tr>
<tr><td><a id="p100204"></a>7</td><td>0,05</td><td>3,4</td><td>3,9</td><td>4,4</td><td>4,9</td><td>5,4</td><td>6,3</td><td>6,9</td><td>12,3</td><td>14</td><td>20,2</td><td>20,6</td><td>23,2</td></tr>
<tr><td><a id="p100205"></a>8</td><td rowspan="3">С выверкой в двух плоскостях</td><td>0,3</td><td>3</td><td>3,6</td><td>4,2</td><td>4,7</td><td>5,1</td><td>6,2</td><td>6,8</td><td>12,9</td><td>15,1</td><td>20,7</td><td>21,2</td><td>25,2</td></tr>
<tr><td><a id="p100206"></a>9</td><td>0,1</td><td>3,4</td><td>3,8</td><td>4,5</td><td>5,1</td><td>5,6</td><td>6,7</td><td>7,3</td><td>14,6</td><td>16,8</td><td>22,4</td><td>22,8</td><td>26,2</td></tr>
<tr><td><a id="p100207"></a>10</td><td>0,05</td><td>4,5</td><td>5</td><td>5,6</td><td>6,2</td><td>6,9</td><td>7,9</td><td>8,5</td><td>17,4</td><td>20,2</td><td>26,9</td><td>27,3</td><td>31,9</td></tr>
<tr><td colspan="3"><a id="p100208"></a>Индекс</td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="13%"><col width="11%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="12" rowspan="2"><a id="p100209"></a>Вспомогательное время на установку и снятие деталей (с учетом времени на обслуживание рабочего места, отдых и личные потребности)</td><td colspan="4">Карта 3</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="4"><a id="p100210"></a>N позиции</td><td rowspan="4">Способ установки и крепления детали</td><td rowspan="4">Характер выверки</td><td rowspan="4">Точность выверки на 1 п/м, мм, до</td><td colspan="7">Вручную</td><td colspan="5">Мостовым краном</td></tr>
<tr><td colspan="12">Масса детали m, кг, до</td></tr>
<tr><td>1</td><td>2</td><td>5</td><td>8</td><td>12</td><td>20</td><td>30</td><td>30</td><td>80</td><td>200</td><td>300</td><td>600</td></tr>
<tr><td colspan="12">Время tву, мин.</td></tr>
<tr><td><a id="p100211"></a>11</td><td rowspan="2">В самоцентрирующем патроне с ручным зажимом</td><td rowspan="3">С выверкой относительно оси растачивания</td><td>0,3</td><td>0,95</td><td>1,25</td><td>1,4</td><td>1,7</td><td>1,8</td><td>2,2</td><td>2,7</td><td>6</td><td>7,4</td><td>9,8</td><td>-</td><td>-</td></tr>
<tr><td><a id="p100212"></a>12</td><td>0,1</td><td>1,9</td><td>2,6</td><td>2,7</td><td>3,4</td><td>3,7</td><td>4,1</td><td>4,6</td><td>7,8</td><td>9,5</td><td>12,8</td><td>-</td><td>-</td></tr>
<tr><td><a id="p100213"></a>13</td><td>В приспособлении</td><td>0,05</td><td>1</td><td>1,3</td><td>1,45</td><td>1,7</td><td>1,9</td><td>2,3</td><td>2,5</td><td>3,6</td><td>4,8</td><td>6,7</td><td>-</td><td>-</td></tr>
<tr><td><a id="p100214"></a>14</td><td colspan="3">Время по карте предусматривает крепление детали болтами в количестве</td><td colspan="12">4</td></tr>
<tr><td><a id="p100215"></a>15</td><td colspan="3">Добавлять (отнимать) на каждый болт сверх (менее) предусмотренных</td><td colspan="6">0,4</td><td colspan="6">0,5</td></tr>
<tr><td colspan="4"><a id="p100216"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td></tr>
</table>


<a id="p100217"></a>*Примечания.* 1. При установке нежестких деталей сварной конструкции время по карте применять с К = 1,2.
2. <a id="p100218"></a>При работе с местным подъемником время, приведенное для мостового крана, уменьшать на 1,5 мин.


<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100219"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Чугуны серые, ковкие и высокопрочные<br>&lt; 167...264 НВ, Ra 1,6...1,0, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="4">Карта 4</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100220"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100221"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100222"></a>1</td><td>10</td><td>0,1</td><td>0,79</td><td>0,90</td><td>1,32</td><td>1,50</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100223"></a>2</td><td>15</td><td>0,12</td><td>0,92</td><td>1,18</td><td>1,40</td><td>1,60</td><td>1,90</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100224"></a>3</td><td>20</td><td>0,15</td><td>1,05</td><td>1,23</td><td>1,48</td><td>1,70</td><td>2,05</td><td>2,55</td><td>2,80</td><td>4,01</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100225"></a>4</td><td>30</td><td>0,2</td><td>1,17</td><td>1,37</td><td>1,66</td><td>1,92</td><td>2,18</td><td>2,85</td><td>2,90</td><td>4,10</td><td colspan="2">4,50</td><td>5,50</td></tr>
<tr><td><a id="p100226"></a>5</td><td>50</td><td>0,3</td><td>1,37</td><td>1,61</td><td>1,97</td><td>2,32</td><td>2,64</td><td>3,12</td><td>3,57</td><td>4,17</td><td colspan="2">4,77</td><td>5,62</td></tr>
<tr><td><a id="p100227"></a>6</td><td>65</td><td>0,35</td><td>1,57</td><td>1,86</td><td>2,30</td><td>2,72</td><td>3,13</td><td>3,72</td><td>4,29</td><td>5,04</td><td colspan="2">5,79</td><td>6,88</td></tr>
<tr><td><a id="p100228"></a>7</td><td>80</td><td>0,4</td><td>1,75</td><td>2,08</td><td>2,60</td><td>3,13</td><td>3,57</td><td>4,26</td><td>4,94</td><td>5,85</td><td colspan="2">6,73</td><td>8,02</td></tr>
<tr><td><a id="p100229"></a>8</td><td>100</td><td>0,5</td><td>1,97</td><td>2,34</td><td>2,95</td><td>3,57</td><td>4,11</td><td>4,94</td><td>5,76</td><td>6,83</td><td colspan="2">7,89</td><td>9,47</td></tr>
<tr><td><a id="p100230"></a>9</td><td>125</td><td>0,6</td><td>2,26</td><td>2,71</td><td>3,46</td><td>4,11</td><td>4,86</td><td>5,89</td><td>6,90</td><td>8,23</td><td colspan="2">9,55</td><td>11,5</td></tr>
<tr><td><a id="p100231"></a>10</td><td>160</td><td>0,8</td><td>2,63</td><td>3,15</td><td>4,06</td><td>4,86</td><td>5,79</td><td>7,05</td><td>8,30</td><td>9,96</td><td colspan="2">12,2</td><td>14,0</td></tr>
<tr><td><a id="p100232"></a>11</td><td>200</td><td>0,8</td><td>3,03</td><td>3,66</td><td>4,75</td><td>5,80</td><td>6,84</td><td>8,38</td><td>9,91</td><td>11,9</td><td colspan="2">14,6</td><td>16,9</td></tr>
<tr><td><a id="p100233"></a>12</td><td>250</td><td>0,9</td><td>3,50</td><td>4,24</td><td>5,54</td><td>6,81</td><td>8,1</td><td>9,90</td><td>11,8</td><td>14,2</td><td colspan="2">17,4</td><td>20,2</td></tr>
<tr><td><a id="p100234"></a>13</td><td>320</td><td>1</td><td>4,09</td><td>5,00</td><td>6,56</td><td>8,09</td><td>9,63</td><td>11,9</td><td>14,1</td><td>17,1</td><td colspan="2">21,0</td><td>24,5</td></tr>
<tr><td><a id="p100235"></a>14</td><td>400</td><td>1,1</td><td>4,67</td><td>5,68</td><td>7,53</td><td>9,34</td><td>11,1</td><td>13,8</td><td>16,4</td><td>20,0</td><td colspan="2">23,4</td><td>28,6</td></tr>
<tr><td colspan="3"><a id="p100236"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100237"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Чугуны серые, ковкие и высокопрочные<br>&lt; 167...264 НВ, Ra 1,6...1,0, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="4">Карта 4</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100238"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100239"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100240"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100241"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100242"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100243"></a>4</td><td>30</td><td>0,2</td><td>6,74</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100244"></a>5</td><td>50</td><td>0,3</td><td>7,4</td><td>8,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100245"></a>6</td><td>65</td><td>0,35</td><td>7,81</td><td>10,8</td><td>13,4</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100246"></a>7</td><td>80</td><td>0,4</td><td>9,12</td><td>12</td><td>15,5</td><td>17,7</td><td>20,6</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100247"></a>8</td><td>100</td><td>0,5</td><td>11,2</td><td>14</td><td>18,5</td><td>21,5</td><td>23,7</td><td>32,5</td><td>37</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100248"></a>9</td><td>125</td><td>0,6</td><td>13,6</td><td>16,9</td><td>19,5</td><td>22,5</td><td>26</td><td>34</td><td>44</td><td>51,5</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100249"></a>10</td><td>160</td><td>0,8</td><td>16,6</td><td>19,5</td><td>22,7</td><td>25,9</td><td>29,3</td><td>37</td><td>46</td><td>53</td><td colspan="2">64</td><td>77</td></tr>
<tr><td><a id="p100250"></a>11</td><td>200</td><td>0,8</td><td>20,1</td><td>23,5</td><td>27,5</td><td>30,6</td><td>36,3</td><td>42,2</td><td>48</td><td>63</td><td colspan="2">75</td><td>83,6</td></tr>
<tr><td><a id="p100251"></a>12</td><td>250</td><td>0,9</td><td>24,1</td><td>28,2</td><td>33</td><td>37,8</td><td>43,7</td><td>50,8</td><td>57,9</td><td>73</td><td colspan="2">83,2</td><td>100</td></tr>
<tr><td><a id="p100252"></a>13</td><td>320</td><td>1</td><td>29,2</td><td>35,4</td><td>40,2</td><td>46</td><td>53,3</td><td>62</td><td>70,8</td><td>80,9</td><td colspan="2">95,1</td><td>115</td></tr>
<tr><td><a id="p100253"></a>14</td><td>400</td><td>1,1</td><td>34,1</td><td>40,2</td><td>47,1</td><td>54</td><td>62,6</td><td>72,9</td><td>83,2</td><td>95,2</td><td colspan="2">110</td><td>130</td></tr>
<tr><td colspan="3"><a id="p100254"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="5%"><col width="4%"><col width="3%"><col width="4%"><col width="12%"></colgroup>
<tr><td colspan="9" rowspan="3"><a id="p100255"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Чугуны серые, ковкие и высокопрочные<br>&lt; 167...264 НВ, Ra 1,6...1,0, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="4">Карта 4</td></tr>
<tr><td colspan="3">Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="13"><a id="p100256"></a>II. Подрезание торцов методом осевой подачи широколезвийными инструментами</td></tr>
<tr><td rowspan="3"><a id="p100257"></a>N позиции</td><td colspan="12">Диаметр обрабатываемого отверстия d, мм, до</td></tr>
<tr><td>50</td><td>65</td><td>80</td><td>100</td><td>125</td><td>160</td><td>200</td><td colspan="2">250</td><td colspan="2">320</td><td>400</td></tr>
<tr><td colspan="12">Время на рабочий ход tнш, мин.</td></tr>
<tr><td rowspan="3"><a id="p100258"></a>15</td><td>1</td><td>1,1</td><td>1,3</td><td>1,6</td><td>1,9</td><td>2,2</td><td>2,4</td><td colspan="2">2,6</td><td colspan="2">2,9</td><td>3,3</td></tr>
<tr><td colspan="12">Индекс</td></tr>
<tr><td><a id="p100259"></a>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td colspan="2">и</td><td>к</td></tr>
<tr><td colspan="13">III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td colspan="13"><a id="p100260"></a>Твердость обрабатываемого материала, НВ</td></tr>
<tr><td colspan="4"><a id="p100261"></a>&lt; 167</td><td colspan="4">167...223</td><td colspan="5">224...264</td></tr>
<tr><td colspan="13"><a id="p100262"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td colspan="2"><a id="p100263"></a>1,0</td><td colspan="2">1,6</td><td colspan="2">1,0</td><td colspan="2">1,6</td><td colspan="3">1,0</td><td colspan="2">1,6</td></tr>
<tr><td colspan="13"><a id="p100264"></a>Коэффициент Ку</td></tr>
<tr><td colspan="2"><a id="p100265"></a>0,6</td><td colspan="2">0,5</td><td colspan="2">0,8</td><td colspan="2">0,7</td><td colspan="3">1,0</td><td colspan="2">0,7</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100266"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Чугуны термообработанные и отбеленные<br>HRCэ 41...47, Ra 1,6...1,0, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="4">Карта 5</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100267"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100268"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100269"></a>1</td><td>10</td><td>0,1</td><td>0,80</td><td>0,95</td><td>1,35</td><td>1,57</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100270"></a>2</td><td>15</td><td>0,12</td><td>0,94</td><td>1,11</td><td>1,45</td><td>1,65</td><td>2,00</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100271"></a>3</td><td>20</td><td>0,15</td><td>1,08</td><td>1,27</td><td>1,53</td><td>1,75</td><td>2,10</td><td>2,64</td><td>2,91</td><td>3,80</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100272"></a>4</td><td>30</td><td>0,2</td><td>1,20</td><td>1,40</td><td>1,70</td><td>1,98</td><td>2,25</td><td>2,95</td><td>3,01</td><td>4,22</td><td colspan="2">5,08</td><td>5,83</td></tr>
<tr><td><a id="p100273"></a>5</td><td>50</td><td>0,3</td><td>1,41</td><td>1,67</td><td>2,05</td><td>2,42</td><td>2,77</td><td>3,28</td><td>3,76</td><td>4,41</td><td colspan="2">5,25</td><td>5,97</td></tr>
<tr><td><a id="p100274"></a>6</td><td>65</td><td>0,35</td><td>1,60</td><td>1,89</td><td>2,34</td><td>2,78</td><td>3,20</td><td>3,81</td><td>4,40</td><td>5,18</td><td colspan="2">5,96</td><td>7,08</td></tr>
<tr><td><a id="p100275"></a>7</td><td>80</td><td>0,4</td><td>1,83</td><td>2,18</td><td>2,74</td><td>3,27</td><td>3,79</td><td>4,54</td><td>5,28</td><td>6,27</td><td colspan="2">7,23</td><td>8,64</td></tr>
<tr><td><a id="p100276"></a>8</td><td>100</td><td>0,5</td><td>2,09</td><td>2,49</td><td>3,16</td><td>3,81</td><td>4,44</td><td>5,36</td><td>6,27</td><td>7,46</td><td colspan="2">8,64</td><td>10,4</td></tr>
<tr><td><a id="p100277"></a>9</td><td>125</td><td>0,6</td><td>2,38</td><td>2,86</td><td>3,66</td><td>4,43</td><td>5,17</td><td>6,29</td><td>7,39</td><td>8,83</td><td colspan="2">10,3</td><td>12,4</td></tr>
<tr><td><a id="p100278"></a>10</td><td>160</td><td>0,8</td><td>2,81</td><td>3,38</td><td>4,38</td><td>5,34</td><td>6,29</td><td>7,69</td><td>9,07</td><td>10,9</td><td colspan="2">12,7</td><td>15,4</td></tr>
<tr><td><a id="p100279"></a>11</td><td>200</td><td>0,8</td><td>3,25</td><td>3,94</td><td>5,13</td><td>6,29</td><td>7,45</td><td>9,15</td><td>10,8</td><td>13,1</td><td colspan="2">15,3</td><td>18,6</td></tr>
<tr><td><a id="p100280"></a>12</td><td>250</td><td>0,9</td><td>3,74</td><td>4,54</td><td>5,97</td><td>7,35</td><td>8,73</td><td>10,8</td><td>12,8</td><td>15,5</td><td colspan="2">18,1</td><td>22,1</td></tr>
<tr><td><a id="p100281"></a>13</td><td>320</td><td>1</td><td>4,47</td><td>5,44</td><td>7,21</td><td>8,93</td><td>10,7</td><td>13,2</td><td>15,7</td><td>19,1</td><td colspan="2">22,4</td><td>27,4</td></tr>
<tr><td><a id="p100282"></a>14</td><td>400</td><td>1,1</td><td>5,21</td><td>6,35</td><td>8,47</td><td>10,5</td><td>12,6</td><td>15,7</td><td>18,7</td><td>22,8</td><td colspan="2">26,8</td><td>32,8</td></tr>
<tr><td colspan="3"><a id="p100283"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100284"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Чугуны термообработанные и отбеленные<br>HRCэ 41...47, Ra 1,6...1,0, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="4">Карта 5</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100285"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100286"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100287"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100288"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100289"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100290"></a>4</td><td>30</td><td>0,2</td><td>6,84</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100291"></a>5</td><td>50</td><td>0,3</td><td>7,75</td><td>10,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100292"></a>6</td><td>65</td><td>0,35</td><td>8,05</td><td>10,8</td><td>14,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100293"></a>7</td><td>80</td><td>0,4</td><td>9,84</td><td>11,5</td><td>15,3</td><td>18,6</td><td>22,6</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100294"></a>8</td><td>100</td><td>0,5</td><td>11,9</td><td>13,9</td><td>16,2</td><td>20,5</td><td>24,5</td><td>35,2</td><td>38,7</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100295"></a>9</td><td>125</td><td>0,6</td><td>14,2</td><td>16,6</td><td>19,4</td><td>22,2</td><td>28,5</td><td>38,2</td><td>48,6</td><td>55,7</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100296"></a>10</td><td>160</td><td>0,8</td><td>17,7</td><td>20,8</td><td>24,3</td><td>27,9</td><td>32,4</td><td>40,7</td><td>50,6</td><td>58,3</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100297"></a>11</td><td>200</td><td>0,8</td><td>21,3</td><td>25,2</td><td>29,5</td><td>33,9</td><td>39,3</td><td>45,8</td><td>52,8</td><td>69,3</td><td colspan="2">82,5</td><td>-</td></tr>
<tr><td><a id="p100298"></a>12</td><td>250</td><td>0,9</td><td>25,4</td><td>30</td><td>35,2</td><td>40,5</td><td>47</td><td>54,8</td><td>62,7</td><td>80,3</td><td colspan="2">91,3</td><td>110</td></tr>
<tr><td><a id="p100299"></a>13</td><td>320</td><td>1</td><td>31,5</td><td>37,3</td><td>43,9</td><td>50,5</td><td>58,7</td><td>68,6</td><td>78,4</td><td>89</td><td colspan="2">105</td><td>127</td></tr>
<tr><td><a id="p100300"></a>14</td><td>400</td><td>1,1</td><td>37,8</td><td>44,8</td><td>52,8</td><td>60,7</td><td>70,6</td><td>82,5</td><td>94,4</td><td>105</td><td colspan="2">121</td><td>143</td></tr>
<tr><td colspan="3"><a id="p100301"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="7%"><col width="3%"><col width="9%"><col width="9%"><col width="5%"><col width="4%"><col width="7%"><col width="12%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100302"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Чугуны термообработанные и отбеленные<br>HRCэ 41...47, Ra 1,6...1,0, 7 квалитет</td><td colspan="3">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="3">Карта 5</td></tr>
<tr><td colspan="2">Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="13"><a id="p100303"></a>II. Подрезание торцов методом осевой подачи широколезвийными инструментами</td></tr>
<tr><td rowspan="3"><a id="p100304"></a>N позиции</td><td colspan="12">Диаметр обрабатываемого отверстия d, мм, до</td></tr>
<tr><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">125</td><td>160</td><td>200</td><td colspan="2">250</td><td>320</td><td>400</td></tr>
<tr><td colspan="12">Время на рабочий ход tнш, мин.</td></tr>
<tr><td rowspan="3"><a id="p100305"></a>15</td><td>1,1</td><td>1,2</td><td>1,4</td><td>1,7</td><td colspan="2">2</td><td>2,3</td><td>2,6</td><td colspan="2">2,8</td><td>3,1</td><td>3,5</td></tr>
<tr><td colspan="12">Индекс</td></tr>
<tr><td><a id="p100306"></a>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td></tr>
<tr><td colspan="13"><a id="p100307"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td colspan="13"><a id="p100308"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td colspan="6"><a id="p100309"></a>1,0</td><td colspan="7">1,6</td></tr>
<tr><td colspan="13"><a id="p100310"></a>Коэффициент Ку</td></tr>
<tr><td colspan="6"><a id="p100311"></a>1,0</td><td colspan="7">0,7</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100312"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Стали углеродистые качественные<br>144...213 НВ, Ra 1,6...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Т30К4</td></tr>
<tr><td colspan="4">Карта 6</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100313"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100314"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100315"></a>1</td><td>10</td><td>0,1</td><td>0,73</td><td>0,81</td><td>0,99</td><td>1,11</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100316"></a>2</td><td>15</td><td>0,12</td><td>0,75</td><td>0,87</td><td>1,09</td><td>1,17</td><td>1,28</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100317"></a>3</td><td>20</td><td>0,15</td><td>0,85</td><td>0,98</td><td>1,13</td><td>1,24</td><td>1,38</td><td>1,68</td><td>1,87</td><td>2,11</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100318"></a>4</td><td>30</td><td>0,2</td><td>0,95</td><td>1,09</td><td>1,26</td><td>1,41</td><td>1,55</td><td>1,75</td><td>1,93</td><td>2,64</td><td colspan="2">2,96</td><td>3,40</td></tr>
<tr><td><a id="p100319"></a>5</td><td>50</td><td>0,3</td><td>1,11</td><td>1,29</td><td>1,52</td><td>1,74</td><td>1,94</td><td>2,22</td><td>2,48</td><td>2,82</td><td colspan="2">3,16</td><td>3,63</td></tr>
<tr><td><a id="p100320"></a>6</td><td>65</td><td>0,35</td><td>1,21</td><td>1,42</td><td>1,68</td><td>1,92</td><td>2,15</td><td>2,47</td><td>2,78</td><td>3,18</td><td colspan="2">3,58</td><td>4,13</td></tr>
<tr><td><a id="p100321"></a>7</td><td>80</td><td>0,4</td><td>1,31</td><td>1,52</td><td>1,82</td><td>2,10</td><td>2,35</td><td>2,71</td><td>3,06</td><td>3,52</td><td colspan="2">3,96</td><td>4,59</td></tr>
<tr><td><a id="p100322"></a>8</td><td>100</td><td>0,5</td><td>1,44</td><td>1,67</td><td>2,02</td><td>2,34</td><td>2,64</td><td>3,07</td><td>3,50</td><td>4,04</td><td colspan="2">4,56</td><td>5,34</td></tr>
<tr><td><a id="p100323"></a>9</td><td>125</td><td>0,6</td><td>1,59</td><td>1,88</td><td>2,28</td><td>2,66</td><td>3,02</td><td>3,55</td><td>4,05</td><td>4,71</td><td colspan="2">5,36</td><td>6,3</td></tr>
<tr><td><a id="p100324"></a>10</td><td>160</td><td>0,8</td><td>1,72</td><td>2,03</td><td>2,49</td><td>2,90</td><td>3,31</td><td>3,90</td><td>4,47</td><td>5,23</td><td colspan="2">6,0</td><td>7,0</td></tr>
<tr><td><a id="p100325"></a>11</td><td>200</td><td>0,8</td><td>1,92</td><td>2,27</td><td>2,81</td><td>3,30</td><td>3,79</td><td>4,49</td><td>5,18</td><td>6,1</td><td colspan="2">7,0</td><td>8,3</td></tr>
<tr><td><a id="p100326"></a>12</td><td>250</td><td>0,9</td><td>2,17</td><td>2,56</td><td>3,20</td><td>3,80</td><td>4,4</td><td>5,2</td><td>6,1</td><td>7,2</td><td colspan="2">8,3</td><td>9,8</td></tr>
<tr><td><a id="p100327"></a>13</td><td>320</td><td>1</td><td>2,46</td><td>2,94</td><td>3,71</td><td>4,43</td><td>5,15</td><td>6,2</td><td>7,2</td><td>8,6</td><td colspan="2">9,9</td><td>11,9</td></tr>
<tr><td><a id="p100328"></a>14</td><td>400</td><td>1,1</td><td>2,84</td><td>3,38</td><td>4,31</td><td>5,20</td><td>6,1</td><td>7,4</td><td>8,6</td><td>10,3</td><td colspan="2">11,9</td><td>14,4</td></tr>
<tr><td colspan="3"><a id="p100329"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100330"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Стали углеродистые качественные<br>144...213 НВ, Ra 1,6...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Т30К4</td></tr>
<tr><td colspan="4">Карта 6</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100331"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100332"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100333"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100334"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100335"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100336"></a>4</td><td>30</td><td>0,2</td><td>3,83</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100337"></a>5</td><td>50</td><td>0,3</td><td>4,37</td><td>5,18</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100338"></a>6</td><td>65</td><td>0,35</td><td>4,62</td><td>6,15</td><td>8,23</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100339"></a>7</td><td>80</td><td>0,4</td><td>5,13</td><td>6,86</td><td>8,53</td><td>9,1</td><td>11,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100340"></a>8</td><td>100</td><td>0,5</td><td>6</td><td>7,88</td><td>8,88</td><td>9,87</td><td>11,9</td><td>16</td><td>18,1</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100341"></a>9</td><td>125</td><td>0,6</td><td>7,11</td><td>8,2</td><td>9,42</td><td>10,7</td><td>12,2</td><td>16,3</td><td>21,8</td><td>24,8</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100342"></a>10</td><td>160</td><td>0,8</td><td>7,93</td><td>9,17</td><td>10,6</td><td>12</td><td>13,7</td><td>17,8</td><td>23,8</td><td>27,1</td><td colspan="2">40,4</td><td>46,7</td></tr>
<tr><td><a id="p100343"></a>11</td><td>200</td><td>0,8</td><td>9,36</td><td>10,9</td><td>12,6</td><td>14,2</td><td>16,3</td><td>18,9</td><td>24,3</td><td>33,4</td><td colspan="2">42,5</td><td>52,6</td></tr>
<tr><td><a id="p100344"></a>12</td><td>250</td><td>0,9</td><td>11,2</td><td>13</td><td>15,1</td><td>17,2</td><td>19,8</td><td>22,9</td><td>25,9</td><td>40,1</td><td colspan="2">45,1</td><td>55,2</td></tr>
<tr><td><a id="p100345"></a>13</td><td>320</td><td>1</td><td>13,5</td><td>15,8</td><td>18,4</td><td>21</td><td>24,2</td><td>28</td><td>31,9</td><td>50,6</td><td colspan="2">56,9</td><td>65,9</td></tr>
<tr><td><a id="p100346"></a>14</td><td>400</td><td>1,1</td><td>16,4</td><td>19,3</td><td>22,5</td><td>25,7</td><td>29,7</td><td>34,5</td><td>39,2</td><td>60,2</td><td colspan="2">67,8</td><td>78,6</td></tr>
<tr><td colspan="3"><a id="p100347"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="5%"><col width="4%"><col width="3%"><col width="4%"><col width="12%"></colgroup>
<tr><td colspan="9" rowspan="3"><a id="p100348"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Стали углеродистые качественные<br>144...213 НВ, Ra 1,6...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Т30К4</td></tr>
<tr><td colspan="4">Карта 6</td></tr>
<tr><td colspan="3">Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="13"><a id="p100349"></a>II. Подрезание торцов методом осевой подачи широколезвийными инструментами</td></tr>
<tr><td rowspan="3"><a id="p100350"></a>N позиции</td><td colspan="12">Диаметр обрабатываемого отверстия d, мм, до</td></tr>
<tr><td>50</td><td>65</td><td>80</td><td>100</td><td>125</td><td>160</td><td>200</td><td colspan="2">250</td><td colspan="2">320</td><td>400</td></tr>
<tr><td colspan="12">Время на рабочий ход tнш, мин.</td></tr>
<tr><td rowspan="3"><a id="p100351"></a>15</td><td>0,3</td><td>0,4</td><td>0,5</td><td>0,6</td><td>0,6</td><td>0,7</td><td>0,8</td><td colspan="2">0,8</td><td colspan="2">0,9</td><td>1</td></tr>
<tr><td colspan="12">Индекс</td></tr>
<tr><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td colspan="2">и</td><td>к</td></tr>
<tr><td colspan="13"><a id="p100352"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td colspan="13"><a id="p100353"></a>Обрабатываемый материал</td></tr>
<tr><td colspan="6"><a id="p100354"></a>стали низкоуглеродистые качественные</td><td colspan="7">стали среднеуглеродистые качественные</td></tr>
<tr><td colspan="6"><a id="p100355"></a>144...213 НВ</td><td colspan="7">150...213 НВ</td></tr>
<tr><td colspan="13"><a id="p100356"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td colspan="2"><a id="p100357"></a>0,63</td><td colspan="2">0,8</td><td colspan="2">1,6</td><td colspan="2">0,63</td><td colspan="3">0,8</td><td colspan="2">1,6</td></tr>
<tr><td colspan="13"><a id="p100358"></a>Коэффициент Ку</td></tr>
<tr><td colspan="2"><a id="p100359"></a>1,0</td><td colspan="2">0,8</td><td colspan="2">0,6</td><td colspan="2">1,3</td><td colspan="3">1,0</td><td colspan="2">0,8</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100360"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Стали легированные конструкционные<br>150...279 НВ, Ra 1,6...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Т30К4</td></tr>
<tr><td colspan="4">Карта 7</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100361"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100362"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100363"></a>1</td><td>10</td><td>0,1</td><td>0,76</td><td>0,98</td><td>1,23</td><td>1,44</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100364"></a>2</td><td>15</td><td>0,12</td><td>0,89</td><td>1,05</td><td>1,32</td><td>1,50</td><td>1,67</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100365"></a>3</td><td>20</td><td>0,15</td><td>1,10</td><td>1,30</td><td>1,57</td><td>1,81</td><td>2,08</td><td>2,53</td><td>3,02</td><td>3,52</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100366"></a>4</td><td>30</td><td>0,2</td><td>1,20</td><td>1,41</td><td>1,71</td><td>1,99</td><td>2,26</td><td>2,65</td><td>3,33</td><td>4,68</td><td colspan="2">5,38</td><td>6,01</td></tr>
<tr><td><a id="p100367"></a>5</td><td>50</td><td>0,3</td><td>1,35</td><td>1,59</td><td>1,95</td><td>2,28</td><td>2,60</td><td>3,06</td><td>3,50</td><td>4,73</td><td colspan="2">5,43</td><td>6,20</td></tr>
<tr><td><a id="p100368"></a>6</td><td>65</td><td>0,35</td><td>1,52</td><td>1,80</td><td>2,21</td><td>2,60</td><td>2,99</td><td>3,54</td><td>4,07</td><td>4,78</td><td colspan="2">5,48</td><td>6,49</td></tr>
<tr><td><a id="p100369"></a>7</td><td>80</td><td>0,4</td><td>1,71</td><td>2,02</td><td>2,52</td><td>3,00</td><td>3,45</td><td>4,11</td><td>4,76</td><td>5,62</td><td colspan="2">6,46</td><td>7,69</td></tr>
<tr><td><a id="p100370"></a>8</td><td>100</td><td>0,5</td><td>1,92</td><td>2,27</td><td>2,86</td><td>3,42</td><td>3,95</td><td>4,75</td><td>5,53</td><td>6,54</td><td colspan="2">7,55</td><td>9,05</td></tr>
<tr><td><a id="p100371"></a>9</td><td>125</td><td>0,6</td><td>2,16</td><td>2,59</td><td>3,28</td><td>3,94</td><td>4,58</td><td>5,54</td><td>6,48</td><td>7,70</td><td colspan="2">8,92</td><td>10,7</td></tr>
<tr><td><a id="p100372"></a>10</td><td>160</td><td>0,8</td><td>2,56</td><td>3,08</td><td>3,95</td><td>4,79</td><td>5,62</td><td>6,84</td><td>8,04</td><td>9,63</td><td colspan="2">11,2</td><td>13,5</td></tr>
<tr><td><a id="p100373"></a>11</td><td>200</td><td>0,8</td><td>2,91</td><td>3,51</td><td>4,54</td><td>5,52</td><td>6,51</td><td>7,95</td><td>9,39</td><td>11,3</td><td colspan="2">13,2</td><td>15,9</td></tr>
<tr><td><a id="p100374"></a>12</td><td>250</td><td>0,9</td><td>3,94</td><td>4,77</td><td>6,28</td><td>7,74</td><td>9,20</td><td>11,3</td><td>13,5</td><td>16,3</td><td colspan="2">19,1</td><td>23,3</td></tr>
<tr><td><a id="p100375"></a>13</td><td>320</td><td>1</td><td>4,28</td><td>5,21</td><td>6,90</td><td>8,56</td><td>10,2</td><td>12,6</td><td>15,1</td><td>18,3</td><td colspan="2">21,5</td><td>26,2</td></tr>
<tr><td><a id="p100376"></a>14</td><td>400</td><td>1,1</td><td>4,73</td><td>5,75</td><td>7,62</td><td>9,45</td><td>11,3</td><td>14,0</td><td>16,7</td><td>20,2</td><td colspan="2">23,8</td><td>29,0</td></tr>
<tr><td colspan="3"><a id="p100377"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100378"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Стали легированные конструкционные<br>150...279 НВ, Ra 1,6...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Т30К4</td></tr>
<tr><td colspan="4">Карта 7</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100379"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100380"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100381"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100382"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100383"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100384"></a>4</td><td>30</td><td>0,2</td><td>6,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100385"></a>5</td><td>50</td><td>0,3</td><td>7</td><td>9,67</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100386"></a>6</td><td>65</td><td>0,35</td><td>7,36</td><td>10,2</td><td>13,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100387"></a>7</td><td>80</td><td>0,4</td><td>8,74</td><td>11,5</td><td>14</td><td>18,2</td><td>21,1</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100388"></a>8</td><td>100</td><td>0,5</td><td>10,3</td><td>12</td><td>16</td><td>18,9</td><td>21,7</td><td>24</td><td>27,3</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100389"></a>9</td><td>125</td><td>0,6</td><td>12,2</td><td>14,3</td><td>16,7</td><td>19,1</td><td>22</td><td>29,4</td><td>33,5</td><td>38,2</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100390"></a>10</td><td>160</td><td>0,8</td><td>15,5</td><td>18,2</td><td>21,2</td><td>24,3</td><td>28,2</td><td>32,7</td><td>40,8</td><td>48,1</td><td colspan="2">63,8</td><td>74</td></tr>
<tr><td><a id="p100391"></a>11</td><td>200</td><td>0,8</td><td>18,3</td><td>21,5</td><td>25,2</td><td>28,8</td><td>33,4</td><td>38,9</td><td>43,2</td><td>49,4</td><td colspan="2">77,8</td><td>96,4</td></tr>
<tr><td><a id="p100392"></a>12</td><td>250</td><td>0,9</td><td>21,3</td><td>25,8</td><td>32,1</td><td>33,9</td><td>40,3</td><td>45,2</td><td>52,2</td><td>70,6</td><td colspan="2">94,6</td><td>110</td></tr>
<tr><td><a id="p100393"></a>13</td><td>320</td><td>1</td><td>26,8</td><td>35,8</td><td>37,2</td><td>42,7</td><td>49,6</td><td>57,8</td><td>66,1</td><td>85,0</td><td colspan="2">115</td><td>144</td></tr>
<tr><td><a id="p100394"></a>14</td><td>400</td><td>1,1</td><td>33,4</td><td>39,6</td><td>46,6</td><td>53,6</td><td>62,3</td><td>72,7</td><td>83,2</td><td>118</td><td colspan="2">140</td><td>175</td></tr>
<tr><td colspan="3"><a id="p100395"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="5%"><col width="4%"><col width="3%"><col width="4%"><col width="12%"></colgroup>
<tr><td colspan="9" rowspan="3"><a id="p100396"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Стали легированные конструкционные<br>150...279 НВ, Ra 1,6...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Т30К4</td></tr>
<tr><td colspan="4">Карта 7</td></tr>
<tr><td colspan="3">Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="13"><a id="p100397"></a>II. Подрезание торцов методом осевой подачи широколезвийными инструментами</td></tr>
<tr><td rowspan="3"><a id="p100398"></a>N позиции</td><td colspan="12">Диаметр обрабатываемого отверстия d, мм, до</td></tr>
<tr><td>50</td><td>65</td><td>80</td><td>100</td><td>125</td><td>160</td><td>200</td><td colspan="2">250</td><td colspan="2">320</td><td>400</td></tr>
<tr><td colspan="12">Время на рабочий ход tнш, мин.</td></tr>
<tr><td rowspan="3"><a id="p100399"></a>15</td><td>0,6</td><td>0,7</td><td>0,8</td><td>1</td><td>1,2</td><td>1,4</td><td>1,5</td><td colspan="2">1,6</td><td colspan="2">1,8</td><td>2,1</td></tr>
<tr><td colspan="12">Индекс</td></tr>
<tr><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td colspan="2">и</td><td>к</td></tr>
<tr><td colspan="13"><a id="p100400"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td colspan="13"><a id="p100401"></a>Твердость обрабатываемого материала, НВ</td></tr>
<tr><td colspan="6"><a id="p100402"></a>150...217</td><td colspan="7">218...279</td></tr>
<tr><td colspan="13"><a id="p100403"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td colspan="2"><a id="p100404"></a>0,63</td><td colspan="2">0,8</td><td colspan="2">1,6</td><td colspan="2">0,63</td><td colspan="3">0,8</td><td colspan="2">1,6</td></tr>
<tr><td colspan="13"><a id="p100405"></a>Коэффициент Ку</td></tr>
<tr><td colspan="2"><a id="p100406"></a>1,15</td><td colspan="2">0,85</td><td colspan="2">0,7</td><td colspan="2">1,35</td><td colspan="3">1,0</td><td colspan="2">0,8</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100407"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Стали высоколегированные и труднообрабатываемые<br>151...280 НВ, Ra 0,8...0,63, термообработанные<br>HRCэ 30...55, Ra 0,8...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Т30К4</td></tr>
<tr><td colspan="4">Карта 8</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100408"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100409"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100410"></a>1</td><td>10</td><td>0,1</td><td>0,92</td><td>1,17</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100411"></a>2</td><td>15</td><td>0,12</td><td>0,98</td><td>1,27</td><td>1,67</td><td>1,96</td><td>2,23</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100412"></a>3</td><td>20</td><td>0,15</td><td>1,11</td><td>1,38</td><td>1,70</td><td>2,06</td><td>2,35</td><td>3,35</td><td>3,78</td><td>4,46</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100413"></a>4</td><td>30</td><td>0,2</td><td>1,36</td><td>1,72</td><td>2,11</td><td>2,49</td><td>2,85</td><td>3,40</td><td>3,88</td><td>5,39</td><td colspan="2">6,20</td><td>7,37</td></tr>
<tr><td><a id="p100414"></a>5</td><td>50</td><td>0,3</td><td>1,55</td><td>1,96</td><td>2,44</td><td>2,89</td><td>3,32</td><td>3,96</td><td>4,47</td><td>6,07</td><td colspan="2">7,02</td><td>8,40</td></tr>
<tr><td><a id="p100415"></a>6</td><td>65</td><td>0,35</td><td>1,77</td><td>2,27</td><td>2,95</td><td>3,39</td><td>3,94</td><td>4,72</td><td>5,48</td><td>6,49</td><td colspan="2">7,49</td><td>8,97</td></tr>
<tr><td><a id="p100416"></a>7</td><td>80</td><td>0,4</td><td>1,99</td><td>2,57</td><td>3,26</td><td>3,93</td><td>4,57</td><td>5,50</td><td>6,39</td><td>7,65</td><td colspan="2">8,86</td><td>10,6</td></tr>
<tr><td><a id="p100417"></a>8</td><td>100</td><td>0,5</td><td>2,24</td><td>3,06</td><td>4,05</td><td>5,31</td><td>6,25</td><td>7,63</td><td>9,01</td><td>10,5</td><td colspan="2">12</td><td>15</td></tr>
<tr><td><a id="p100418"></a>9</td><td>125</td><td>0,6</td><td>2,56</td><td>3,39</td><td>4,37</td><td>5,35</td><td>6,30</td><td>7,70</td><td>9,10</td><td>10,9</td><td colspan="2">12,5</td><td>15,3</td></tr>
<tr><td><a id="p100419"></a>10</td><td>160</td><td>0,8</td><td>2,66</td><td>3,51</td><td>4,53</td><td>5,5</td><td>6,47</td><td>7,89</td><td>9,28</td><td>11,1</td><td colspan="2">13</td><td>15,7</td></tr>
<tr><td><a id="p100420"></a>11</td><td>200</td><td>0,8</td><td>3,07</td><td>4,09</td><td>5,31</td><td>6,49</td><td>7,67</td><td>9,39</td><td>11,1</td><td>13,4</td><td colspan="2">15,6</td><td>19</td></tr>
<tr><td><a id="p100421"></a>12</td><td>250</td><td>0,9</td><td>3,51</td><td>4,73</td><td>6,19</td><td>7,61</td><td>9,02</td><td>11,1</td><td>12,9</td><td>15,9</td><td colspan="2">18,6</td><td>22,6</td></tr>
<tr><td><a id="p100422"></a>13</td><td>320</td><td>1</td><td>4,16</td><td>5,69</td><td>7,51</td><td>9,30</td><td>11,1</td><td>13,7</td><td>16,3</td><td>19,8</td><td colspan="2">23,2</td><td>28,3</td></tr>
<tr><td><a id="p100423"></a>14</td><td>400</td><td>1,1</td><td>4,87</td><td>6,68</td><td>8,88</td><td>11</td><td>13,2</td><td>16,4</td><td>19,5</td><td>23,7</td><td colspan="2">27,9</td><td>34,1</td></tr>
<tr><td colspan="3"><a id="p100424"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100425"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Стали высоколегированные и труднообрабатываемые<br>151...280 НВ, Ra 1,6...0,63, термообработанные<br>HRCэ 30...55, Ra 0,8...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Т30К4</td></tr>
<tr><td colspan="4">Карта 8</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100426"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100427"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100428"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100429"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100430"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100431"></a>4</td><td>30</td><td>0,2</td><td>12,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100432"></a>5</td><td>50</td><td>0,3</td><td>13,5</td><td>14,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100433"></a>6</td><td>65</td><td>0,35</td><td>14</td><td>17,0</td><td>23,9</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100434"></a>7</td><td>80</td><td>0,4</td><td>14,5</td><td>18,0</td><td>24,2</td><td>25,4</td><td>30,8</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100435"></a>8</td><td>100</td><td>0,5</td><td>17,0</td><td>19,4</td><td>25,4</td><td>26,8</td><td>31,1</td><td>35,5</td><td>40,0</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100436"></a>9</td><td>125</td><td>0,6</td><td>17,4</td><td>20,6</td><td>26,0</td><td>28,0</td><td>32,7</td><td>36,9</td><td>42,0</td><td>45,1</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100437"></a>10</td><td>160</td><td>0,8</td><td>18,0</td><td>21,4</td><td>28,6</td><td>30,3</td><td>33,8</td><td>38,1</td><td>43,5</td><td>68,3</td><td colspan="2">78,7</td><td>114</td></tr>
<tr><td><a id="p100438"></a>11</td><td>200</td><td>0,8</td><td>21,8</td><td>25,6</td><td>29,8</td><td>34,5</td><td>40,0</td><td>46,5</td><td>71,2</td><td>81,5</td><td colspan="2">100</td><td>132</td></tr>
<tr><td><a id="p100439"></a>12</td><td>250</td><td>0,9</td><td>26,0</td><td>30,7</td><td>36,1</td><td>41,4</td><td>48,1</td><td>56,0</td><td>74,0</td><td>97,4</td><td colspan="2">120</td><td>150</td></tr>
<tr><td><a id="p100440"></a>13</td><td>320</td><td>1</td><td>32,6</td><td>38,5</td><td>45,3</td><td>52,1</td><td>60,5</td><td>70,6</td><td>80,7</td><td>121</td><td colspan="2">140</td><td>170</td></tr>
<tr><td><a id="p100441"></a>14</td><td>400</td><td>1,1</td><td>39,3</td><td>46,6</td><td>54,9</td><td>63,1</td><td>73,4</td><td>85,8</td><td>98,1</td><td>151</td><td colspan="2">174</td><td>190</td></tr>
<tr><td colspan="3"><a id="p100442"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="5%"><col width="4%"><col width="7%"><col width="12%"></colgroup>
<tr><td colspan="9" rowspan="3"><a id="p100443"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Стали высоколегированные и труднообрабатываемые<br>151...280 НВ, Ra 1,6...0,63, термообработанные<br>HRCэ 30...55, Ra 0,8...0,63, 7 квалитет</td><td colspan="3">Резцы с пластинами<br>Т30К4</td></tr>
<tr><td colspan="3">Карта 8</td></tr>
<tr><td colspan="2">Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="12"><a id="p100444"></a>II. Подрезание торцов методом осевой подачи широколезвийными инструментами</td></tr>
<tr><td rowspan="3"><a id="p100445"></a>N позиции</td><td colspan="11">Диаметр обрабатываемого отверстия d, мм, до</td></tr>
<tr><td>50</td><td>65</td><td>80</td><td>100</td><td>125</td><td>160</td><td>200</td><td colspan="2">250</td><td>320</td><td>400</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td rowspan="3"><a id="p100446"></a>15</td><td>0,8</td><td>0,9</td><td>1,1</td><td>1,3</td><td>1,5</td><td>1,7</td><td>1,9</td><td colspan="2">2,2</td><td>2,5</td><td>2,9</td></tr>
<tr><td colspan="11">Индекс</td></tr>
<tr><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td></tr>
<tr><td colspan="12"><a id="p100447"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td colspan="12"><a id="p100448"></a>Обрабатываемый материал</td></tr>
<tr><td colspan="6"><a id="p100449"></a>стали высоколегированные и труднообрабатываемые</td><td colspan="6">стали термообработанные</td></tr>
<tr><td colspan="12"><a id="p100450"></a>Твердость стали</td></tr>
<tr><td colspan="3"><a id="p100451"></a>151...224 НВ</td><td colspan="3">225...280 НВ</td><td colspan="3">HRCэ 30...35</td><td colspan="3">HRCэ 36...55</td></tr>
<tr><td colspan="12"><a id="p100452"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td colspan="2"><a id="p100453"></a>1,0</td><td>1,6</td><td>0,63</td><td>0,8</td><td>1,6</td><td>0,63</td><td colspan="2">0,8</td><td colspan="2">0,63</td><td>0,8</td></tr>
<tr><td colspan="12"><a id="p100454"></a>Коэффициент Ку</td></tr>
<tr><td colspan="2"><a id="p100455"></a>0,95</td><td>0,75</td><td>1,3</td><td>1,0</td><td>0,85</td><td>1,2</td><td colspan="2">0,95</td><td colspan="2">1,5</td><td>1,25</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100456"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Бронзы, латуни<br>&lt; 119...&gt;= 119 НВ, Ra 1,6...0,32, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="4">Карта 9</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100457"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100458"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100459"></a>1</td><td>10</td><td>0,1</td><td>0,71</td><td>0,84</td><td>1,01</td><td>1,13</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100460"></a>2</td><td>15</td><td>0,12</td><td>0,76</td><td>0,89</td><td>1,12</td><td>1,27</td><td>1,39</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100461"></a>3</td><td>20</td><td>0,15</td><td>0,91</td><td>1,05</td><td>1,23</td><td>1,37</td><td>1,53</td><td>2,09</td><td>2,36</td><td>2,71</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100462"></a>4</td><td>30</td><td>0,2</td><td>1,06</td><td>1,22</td><td>1,45</td><td>1,66</td><td>1,86</td><td>2,13</td><td>2,40</td><td>2,78</td><td colspan="2">3,02</td><td>3,88</td></tr>
<tr><td><a id="p100463"></a>5</td><td>50</td><td>0,3</td><td>1,19</td><td>1,39</td><td>1,66</td><td>1,92</td><td>2,15</td><td>2,49</td><td>2,81</td><td>3,23</td><td colspan="2">4,12</td><td>4,24</td></tr>
<tr><td><a id="p100464"></a>6</td><td>65</td><td>0,35</td><td>1,32</td><td>1,54</td><td>1,86</td><td>2,15</td><td>2,43</td><td>2,84</td><td>3,22</td><td>3,72</td><td colspan="2">4,22</td><td>4,93</td></tr>
<tr><td><a id="p100465"></a>7</td><td>80</td><td>0,4</td><td>1,37</td><td>1,59</td><td>1,92</td><td>2,22</td><td>2,50</td><td>2,90</td><td>3,29</td><td>3,81</td><td colspan="2">4,30</td><td>5,01</td></tr>
<tr><td><a id="p100466"></a>8</td><td>100</td><td>0,5</td><td>1,51</td><td>1,76</td><td>2,14</td><td>2,50</td><td>2,83</td><td>3,32</td><td>3,79</td><td>4,40</td><td colspan="2">5,00</td><td>5,9</td></tr>
<tr><td><a id="p100467"></a>9</td><td>125</td><td>0,6</td><td>1,58</td><td>1,86</td><td>2,26</td><td>2,63</td><td>2,98</td><td>3,50</td><td>4,01</td><td>4,65</td><td colspan="2">5,3</td><td>6,2</td></tr>
<tr><td><a id="p100468"></a>10</td><td>160</td><td>0,8</td><td>1,80</td><td>2,12</td><td>2,61</td><td>3,07</td><td>3,51</td><td>4,16</td><td>4,78</td><td>5,6</td><td colspan="2">6,4</td><td>7,6</td></tr>
<tr><td><a id="p100469"></a>11</td><td>200</td><td>0,8</td><td>1,91</td><td>2,26</td><td>2,78</td><td>3,26</td><td>3,75</td><td>4,44</td><td>5,1</td><td>6,0</td><td colspan="2">6,9</td><td>8,2</td></tr>
<tr><td><a id="p100470"></a>12</td><td>250</td><td>0,9</td><td>2,15</td><td>2,55</td><td>3,18</td><td>3,77</td><td>4,35</td><td>5,2</td><td>6,0</td><td>7,1</td><td colspan="2">8,2</td><td>9,7</td></tr>
<tr><td><a id="p100471"></a>13</td><td>320</td><td>1</td><td>2,33</td><td>2,76</td><td>3,47</td><td>4,12</td><td>4,8</td><td>5,7</td><td>6,6</td><td>7,8</td><td colspan="2">9,0</td><td>10,8</td></tr>
<tr><td><a id="p100472"></a>14</td><td>400</td><td>1,1</td><td>2,63</td><td>3,12</td><td>3,94</td><td>4,7</td><td>5,5</td><td>6,6</td><td>7,7</td><td>9,2</td><td colspan="2">10,6</td><td>12,7</td></tr>
<tr><td colspan="3"><a id="p100473"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100474"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Бронзы, латуни<br>&lt; 119...&gt;= 119 НВ, Ra 1,6...0,32, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="4">Карта 9</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100475"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100476"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100477"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100478"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100479"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100480"></a>4</td><td>30</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100481"></a>5</td><td>50</td><td>0,3</td><td>5,4</td><td>6,19</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100482"></a>6</td><td>65</td><td>0,35</td><td>5,54</td><td>7,45</td><td>8,56</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100483"></a>7</td><td>80</td><td>0,4</td><td>5,63</td><td>7,53</td><td>8,66</td><td>9,77</td><td>11,2</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100484"></a>8</td><td>100</td><td>0,5</td><td>6,62</td><td>8,66</td><td>8,77</td><td>9,89</td><td>12,5</td><td>15,4</td><td>20,6</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100485"></a>9</td><td>125</td><td>0,6</td><td>7</td><td>9,31</td><td>9,58</td><td>10,5</td><td>13</td><td>16,1</td><td>22,7</td><td>28,1</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100486"></a>10</td><td>160</td><td>0,8</td><td>8,59</td><td>9,95</td><td>11,5</td><td>13</td><td>14,9</td><td>17,2</td><td>24,1</td><td>35,5</td><td colspan="2">39,9</td><td>46,1</td></tr>
<tr><td><a id="p100487"></a>11</td><td>200</td><td>0,8</td><td>9,23</td><td>10,7</td><td>12,4</td><td>14</td><td>16,1</td><td>18,6</td><td>26,6</td><td>38,1</td><td colspan="2">40,5</td><td>46,8</td></tr>
<tr><td><a id="p100488"></a>12</td><td>250</td><td>0,9</td><td>11,1</td><td>12,9</td><td>14,9</td><td>17</td><td>19,6</td><td>22,6</td><td>28,6</td><td>43,7</td><td colspan="2">49,1</td><td>56,8</td></tr>
<tr><td><a id="p100489"></a>13</td><td>320</td><td>1</td><td>12,3</td><td>14,3</td><td>16,6</td><td>18,9</td><td>21,8</td><td>25,2</td><td>31,7</td><td>45,8</td><td colspan="2">51,6</td><td>59,7</td></tr>
<tr><td><a id="p100490"></a>14</td><td>400</td><td>1,1</td><td>14,5</td><td>17</td><td>19,8</td><td>22,6</td><td>26,1</td><td>30,2</td><td>34,3</td><td>55</td><td colspan="2">62</td><td>71,8</td></tr>
<tr><td colspan="3"><a id="p100491"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="9%"><col width="4%"><col width="6%"><col width="9%"><col width="9%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="7%"><col width="12%"></colgroup>
<tr><td colspan="11" rowspan="3"><a id="p100492"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Бронзы, латуни<br>&lt; 119...&gt;= 119 НВ, Ra 1,6...0,32, 7 квалитет</td><td colspan="3">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="3">Карта 9</td></tr>
<tr><td colspan="2">Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="14"><a id="p100493"></a>II. Подрезание торцов методом осевой подачи широколезвийными инструментами</td></tr>
<tr><td rowspan="3"><a id="p100494"></a>N позиции</td><td colspan="13">Диаметр обрабатываемого отверстия d, мм, до</td></tr>
<tr><td>50</td><td>65</td><td>80</td><td colspan="2">100</td><td>125</td><td>160</td><td colspan="2">200</td><td colspan="2">250</td><td>320</td><td>400</td></tr>
<tr><td colspan="13">Время на рабочий ход tнш, мин.</td></tr>
<tr><td rowspan="3"><a id="p100495"></a>15</td><td>0,3</td><td>0,3</td><td>0,4</td><td colspan="2">0,4</td><td>0,5</td><td>0,5</td><td colspan="2">0,6</td><td colspan="2">0,7</td><td>0,8</td><td>0,9</td></tr>
<tr><td colspan="13">Индекс</td></tr>
<tr><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td colspan="2">ж</td><td colspan="2">з</td><td>и</td><td>к</td></tr>
<tr><td colspan="14"><a id="p100496"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td colspan="14"><a id="p100497"></a>Твердость обрабатываемого материала, НВ</td></tr>
<tr><td colspan="7"><a id="p100498"></a>&lt; 119</td><td colspan="7">&gt;= 119</td></tr>
<tr><td colspan="14"><a id="p100499"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td colspan="2"><a id="p100500"></a>0,32</td><td>0,4</td><td colspan="2">0,8</td><td colspan="2">1,6</td><td colspan="2">0,4</td><td colspan="3">0,8</td><td colspan="2">1,6</td></tr>
<tr><td colspan="14"><a id="p100501"></a>Коэффициент Ку</td></tr>
<tr><td colspan="2"><a id="p100502"></a>1,35</td><td>1,2</td><td colspan="2">0,8</td><td colspan="2">0,6</td><td colspan="2">1,5</td><td colspan="3">1,0</td><td colspan="2">0,75</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100503"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Алюминиевые сплавы<br>&lt; 74...110 НВ, Ra 1,6...0,32, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="4">Карта 10</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100504"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100505"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100506"></a>1</td><td>10</td><td>0,1</td><td>0,75</td><td>0,88</td><td>0,94</td><td>1,16</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100507"></a>2</td><td>15</td><td>0,12</td><td>0,76</td><td>0,89</td><td>1,01</td><td>1,21</td><td>1,32</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100508"></a>3</td><td>20</td><td>0,15</td><td>0,89</td><td>1,04</td><td>1,21</td><td>1,34</td><td>1,50</td><td>1,69</td><td>1,90</td><td>2,42</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100509"></a>4</td><td>30</td><td>0,2</td><td>0,95</td><td>1,10</td><td>1,28</td><td>1,43</td><td>1,58</td><td>1,78</td><td>1,97</td><td>2,52</td><td colspan="2">2,82</td><td>3,22</td></tr>
<tr><td><a id="p100510"></a>5</td><td>50</td><td>0,3</td><td>1,06</td><td>1,23</td><td>1,44</td><td>1,63</td><td>1,80</td><td>2,04</td><td>2,27</td><td>2,56</td><td colspan="2">2,85</td><td>3,24</td></tr>
<tr><td><a id="p100511"></a>6</td><td>65</td><td>0,3</td><td>1,17</td><td>1,36</td><td>1,60</td><td>1,82</td><td>2,03</td><td>2,31</td><td>2,58</td><td>2,94</td><td colspan="2">3,29</td><td>3,78</td></tr>
<tr><td><a id="p100512"></a>7</td><td>80</td><td>0,4</td><td>1,22</td><td>1,41</td><td>1,66</td><td>1,89</td><td>2,11</td><td>2,40</td><td>2,68</td><td>3,05</td><td colspan="2">3,40</td><td>3,90</td></tr>
<tr><td><a id="p100513"></a>8</td><td>100</td><td>0,5</td><td>1,33</td><td>1,54</td><td>1,83</td><td>2,10</td><td>2,34</td><td>2,69</td><td>3,03</td><td>3,46</td><td colspan="2">3,88</td><td>4,5</td></tr>
<tr><td><a id="p100514"></a>9</td><td>125</td><td>0,6</td><td>1,39</td><td>1,62</td><td>1,93</td><td>2,20</td><td>2,46</td><td>2,83</td><td>3,19</td><td>3,64</td><td colspan="2">4,1</td><td>4,7</td></tr>
<tr><td><a id="p100515"></a>10</td><td>160</td><td>0,8</td><td>1,53</td><td>1,79</td><td>2,15</td><td>2,47</td><td>2,79</td><td>3,23</td><td>3,66</td><td>4,2</td><td colspan="2">4,8</td><td>5,5</td></tr>
<tr><td><a id="p100516"></a>11</td><td>200</td><td>0,8</td><td>1,62</td><td>1,90</td><td>2,28</td><td>2,62</td><td>2,96</td><td>3,43</td><td>3,9</td><td>4,5</td><td colspan="2">5,1</td><td>5,9</td></tr>
<tr><td><a id="p100517"></a>12</td><td>250</td><td>0,9</td><td>1,78</td><td>2,08</td><td>2,53</td><td>2,93</td><td>3,32</td><td>3,9</td><td>4,4</td><td>5,1</td><td colspan="2">5,8</td><td>6,8</td></tr>
<tr><td><a id="p100518"></a>13</td><td>320</td><td>1</td><td>1,89</td><td>2,22</td><td>2,71</td><td>3,14</td><td>3,6</td><td>4,2</td><td>4,8</td><td>5,6</td><td colspan="2">6,3</td><td>7,4</td></tr>
<tr><td><a id="p100519"></a>14</td><td>400</td><td>1,1</td><td>2,11</td><td>2,48</td><td>3,04</td><td>3,6</td><td>4,1</td><td>4,8</td><td>5,5</td><td>6,5</td><td colspan="2">7,4</td><td>8,7</td></tr>
<tr><td colspan="3"><a id="p100520"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100521"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Алюминиевые сплавы<br>&lt; 74...110 НВ, Ra 1,6...0,32, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="4">Карта 10</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100522"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100523"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100524"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100525"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100526"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100527"></a>4</td><td>30</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100528"></a>5</td><td>50</td><td>0,3</td><td>4,08</td><td>4,64</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100529"></a>6</td><td>65</td><td>0,3</td><td>4,21</td><td>4,87</td><td>6</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100530"></a>7</td><td>80</td><td>0,4</td><td>4,33</td><td>5,22</td><td>6,3</td><td>7,05</td><td>7,98</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100531"></a>8</td><td>100</td><td>0,5</td><td>5,01</td><td>5,7</td><td>6,49</td><td>7,26</td><td>8,16</td><td>10,6</td><td>12,2</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100532"></a>9</td><td>125</td><td>0,6</td><td>5,28</td><td>6,01</td><td>6,83</td><td>7,65</td><td>8,67</td><td>10,7</td><td>14,6</td><td>16,6</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100533"></a>10</td><td>160</td><td>0,8</td><td>6,21</td><td>7,12</td><td>8,11</td><td>9,14</td><td>10,4</td><td>11,9</td><td>18,4</td><td>20,8</td><td colspan="2">23,3</td><td>26,8</td></tr>
<tr><td><a id="p100534"></a>11</td><td>200</td><td>0,8</td><td>6,63</td><td>7,6</td><td>8,7</td><td>9,78</td><td>11,1</td><td>12,7</td><td>19,1</td><td>21,6</td><td colspan="2">24,2</td><td>27,8</td></tr>
<tr><td><a id="p100535"></a>12</td><td>250</td><td>0,9</td><td>7,77</td><td>8,86</td><td>10,2</td><td>11,5</td><td>13,1</td><td>15</td><td>20</td><td>26,1</td><td colspan="2">29,3</td><td>32,7</td></tr>
<tr><td><a id="p100536"></a>13</td><td>320</td><td>1</td><td>8,38</td><td>9,66</td><td>11,1</td><td>12,6</td><td>14,3</td><td>16,5</td><td>21,6</td><td>28,2</td><td colspan="2">30,0</td><td>33,4</td></tr>
<tr><td><a id="p100537"></a>14</td><td>400</td><td>1,1</td><td>9,9</td><td>11,5</td><td>13,2</td><td>15</td><td>17,2</td><td>19,8</td><td>22,4</td><td>29,4</td><td colspan="2">30,5</td><td>35</td></tr>
<tr><td colspan="3"><a id="p100538"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="6%"><col width="3%"><col width="9%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="7%"><col width="12%"></colgroup>
<tr><td colspan="11" rowspan="3"><a id="p100539"></a>Неполное штучное время<br>Растачивание отверстий и подрезание торцов методом осевой подачи широколезвийными инструментами<br>Алюминиевые сплавы<br>&lt; 74...110 НВ, Ra 1,6...0,32, 7 квалитет</td><td colspan="3">Резцы с пластинами<br>ВК3М (ВК3, ВК60М)</td></tr>
<tr><td colspan="3">Карта 10</td></tr>
<tr><td colspan="2">Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="14"><a id="p100540"></a>II. Подрезание торцов методом осевой подачи широколезвийными инструментами</td></tr>
<tr><td rowspan="3"><a id="p100541"></a>N позиции</td><td colspan="13">Диаметр обрабатываемого отверстия d, мм, до</td></tr>
<tr><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">125</td><td>160</td><td colspan="2">200</td><td colspan="2">250</td><td>320</td><td>400</td></tr>
<tr><td colspan="13">Время на рабочий ход tнш, мин.</td></tr>
<tr><td rowspan="3"><a id="p100542"></a>15</td><td>0,2</td><td>0,3</td><td>0,3</td><td>0,3</td><td colspan="2">0,4</td><td>0,4</td><td colspan="2">0,5</td><td colspan="2">0,5</td><td>0,6</td><td>0,7</td></tr>
<tr><td colspan="13">Индекс</td></tr>
<tr><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td colspan="2">ж</td><td colspan="2">з</td><td>и</td><td>к</td></tr>
<tr><td colspan="14"><a id="p100543"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td colspan="14"><a id="p100544"></a>Твердость обрабатываемого материала, НВ</td></tr>
<tr><td colspan="6"><a id="p100545"></a>&lt; 74</td><td colspan="8">74...110</td></tr>
<tr><td colspan="14"><a id="p100546"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td colspan="2"><a id="p100547"></a>0,32</td><td colspan="2">0,8</td><td colspan="2">1,6</td><td colspan="3">0,32</td><td colspan="3">0,8</td><td colspan="2">1,6</td></tr>
<tr><td colspan="14"><a id="p100548"></a>Коэффициент Ку</td></tr>
<tr><td colspan="2"><a id="p100549"></a>1,2</td><td colspan="2">0,85</td><td colspan="2">0,7</td><td colspan="3">1,7</td><td colspan="3">1</td><td colspan="2">0,8</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100550"></a>Неполное штучное время<br>Растачивание отверстий<br>Чугуны серые, ковкие и высокопрочные<br>167..264 НВ, Ra 1,6...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="4">Карта 11</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100551"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100552"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100553"></a>1</td><td>10</td><td>0,1</td><td>0,75</td><td>0,88</td><td>1,08</td><td>1,17</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100554"></a>2</td><td>15</td><td>0,12</td><td>0,80</td><td>0,93</td><td>1,14</td><td>1,20</td><td>1,42</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100555"></a>3</td><td>20</td><td>0,15</td><td>0,87</td><td>1,00</td><td>1,16</td><td>1,28</td><td>1,50</td><td>1,65</td><td>1,88</td><td>2,36</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100556"></a>4</td><td>30</td><td>0,2</td><td>0,95</td><td>1,10</td><td>1,28</td><td>1,43</td><td>1,58</td><td>1,78</td><td>1,97</td><td>2,38</td><td colspan="2">2,40</td><td>2,76</td></tr>
<tr><td><a id="p100557"></a>5</td><td>50</td><td>0,3</td><td>1,02</td><td>1,24</td><td>1,43</td><td>1,55</td><td>1,67</td><td>2,04</td><td>2,10</td><td>2,40</td><td colspan="2">2,50</td><td>2,96</td></tr>
<tr><td><a id="p100558"></a>6</td><td>65</td><td>0,35</td><td>1,07</td><td>1,29</td><td>1,53</td><td>1,64</td><td>1,76</td><td>2,10</td><td>2,18</td><td>2,44</td><td colspan="2">2,70</td><td>3,04</td></tr>
<tr><td><a id="p100559"></a>7</td><td>80</td><td>0,4</td><td>1,15</td><td>1,32</td><td>1,59</td><td>1,74</td><td>1,91</td><td>2,15</td><td>2,38</td><td>2,68</td><td colspan="2">2,96</td><td>3,35</td></tr>
<tr><td><a id="p100560"></a>8</td><td>100</td><td>0,5</td><td>1,24</td><td>1,43</td><td>1,68</td><td>1,90</td><td>2,10</td><td>2,39</td><td>2,66</td><td>3,01</td><td colspan="2">3,34</td><td>3,8</td></tr>
<tr><td><a id="p100561"></a>9</td><td>125</td><td>0,6</td><td>1,34</td><td>1,56</td><td>1,84</td><td>2,09</td><td>2,32</td><td>2,67</td><td>2,99</td><td>3,39</td><td colspan="2">3,8</td><td>4,4</td></tr>
<tr><td><a id="p100562"></a>10</td><td>160</td><td>0,8</td><td>1,43</td><td>1,65</td><td>1,96</td><td>2,23</td><td>2,49</td><td>2,85</td><td>3,20</td><td>3,7</td><td colspan="2">4,1</td><td>4,7</td></tr>
<tr><td><a id="p100563"></a>11</td><td>200</td><td>0,8</td><td>1,56</td><td>1,82</td><td>2,17</td><td>2,48</td><td>2,79</td><td>3,22</td><td>3,6</td><td>4,2</td><td colspan="2">4,7</td><td>5,5</td></tr>
<tr><td><a id="p100564"></a>12</td><td>250</td><td>0,9</td><td>1,71</td><td>2,00</td><td>2,41</td><td>2,78</td><td>3,14</td><td>3,6</td><td>4,1</td><td>4,8</td><td colspan="2">5,4</td><td>6,3</td></tr>
<tr><td><a id="p100565"></a>13</td><td>320</td><td>1</td><td>1,91</td><td>2,24</td><td>2,73</td><td>3,18</td><td>3,6</td><td>4,2</td><td>4,9</td><td>5,7</td><td colspan="2">6,4</td><td>7,6</td></tr>
<tr><td><a id="p100566"></a>14</td><td>400</td><td>1</td><td>2,13</td><td>2,51</td><td>3,08</td><td>3,6</td><td>4,1</td><td>4,9</td><td>5,6</td><td>6,6</td><td colspan="2">7,6</td><td>8,9</td></tr>
<tr><td colspan="3"><a id="p100567"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100568"></a>Неполное штучное время<br>Растачивание отверстий<br>Чугуны серые, ковкие и высокопрочные<br>167..264 НВ, Ra 1,6...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="4">Карта 11</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100569"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100570"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100571"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100572"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100573"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100574"></a>4</td><td>30</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100575"></a>5</td><td>50</td><td>0,3</td><td>3,28</td><td>3,8</td><td>4,37</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100576"></a>6</td><td>65</td><td>0,3</td><td>3,35</td><td>4,09</td><td>4,51</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100577"></a>7</td><td>80</td><td>0,4</td><td>3,7</td><td>4,15</td><td>4,62</td><td>5,25</td><td>6,65</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100578"></a>8</td><td>100</td><td>0,5</td><td>4,23</td><td>4,77</td><td>5,38</td><td>5,97</td><td>7,5</td><td>8,2</td><td>12,6</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100579"></a>9</td><td>125</td><td>0,6</td><td>4,84</td><td>5,5</td><td>6,22</td><td>6,94</td><td>7,84</td><td>8,83</td><td>15,1</td><td>17,1</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100580"></a>10</td><td>160</td><td>0,8</td><td>5,24</td><td>5,95</td><td>6,73</td><td>7,54</td><td>8,53</td><td>9,69</td><td>16,1</td><td>18,3</td><td colspan="2">20,4</td><td>23,4</td></tr>
<tr><td><a id="p100581"></a>11</td><td>200</td><td>0,8</td><td>6,1</td><td>6,96</td><td>7,95</td><td>8,91</td><td>10,1</td><td>11,5</td><td>19,4</td><td>22</td><td colspan="2">24,6</td><td>28,3</td></tr>
<tr><td><a id="p100582"></a>12</td><td>250</td><td>0,9</td><td>7,1</td><td>8,15</td><td>9,34</td><td>10,5</td><td>12</td><td>13,7</td><td>19,8</td><td>26,4</td><td colspan="2">29,6</td><td>34,1</td></tr>
<tr><td><a id="p100583"></a>13</td><td>320</td><td>1</td><td>8,52</td><td>9,83</td><td>11,3</td><td>12,8</td><td>14,6</td><td>16,8</td><td>20,5</td><td>32,9</td><td colspan="2">36,9</td><td>42,5</td></tr>
<tr><td><a id="p100584"></a>14</td><td>400</td><td>1</td><td>10,1</td><td>11,7</td><td>13,5</td><td>15,3</td><td>17,6</td><td>20,2</td><td>22,9</td><td>40,2</td><td colspan="2">45,1</td><td>52,1</td></tr>
<tr><td colspan="3"><a id="p100585"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="20%"><col width="20%"><col width="20%"><col width="17%"><col width="3%"><col width="8%"><col width="12%"></colgroup>
<tr><td colspan="4" rowspan="3"><a id="p100586"></a>Неполное штучное время<br>Растачивание отверстий<br>Чугуны серые, ковкие и высокопрочные<br>167..264 НВ, Ra 1,6...0,63, 7 квалитет</td><td colspan="3">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="3">Карта 11</td></tr>
<tr><td colspan="2">Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="7"><a id="p100587"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td colspan="7"><a id="p100588"></a>Твердость обрабатываемого материала, НВ</td></tr>
<tr><td colspan="2"><a id="p100589"></a>167...223</td><td colspan="5">224...264</td></tr>
<tr><td colspan="7"><a id="p100590"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td><a id="p100591"></a>0,63</td><td>0,8</td><td>0,63</td><td colspan="2">0,8</td><td colspan="2">1,6</td></tr>
<tr><td colspan="7"><a id="p100592"></a>Коэффициент Ку</td></tr>
<tr><td><a id="p100593"></a>1,2</td><td>0,8</td><td>1,5</td><td colspan="2">1,0</td><td colspan="2">0,75</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100594"></a>Неполное штучное время<br>Растачивание отверстий<br>Чугуны серые, ковкие и высокопрочные<br>167..264 НВ, Ra 0,8...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 10 (Гексанит-Р), Исмит</td></tr>
<tr><td colspan="4">Карта 12</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100595"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100596"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100597"></a>1</td><td>10</td><td>0,1</td><td>0,75</td><td>0,88</td><td>1,01</td><td>1,13</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100598"></a>2</td><td>15</td><td>0,12</td><td>0,80</td><td>0,94</td><td>1,09</td><td>1,23</td><td>1,34</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100599"></a>3</td><td>20</td><td>0,15</td><td>0,88</td><td>1,02</td><td>1,18</td><td>1,31</td><td>1,56</td><td>1,76</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100600"></a>4</td><td>30</td><td>0,2</td><td>1,01</td><td>1,17</td><td>1,38</td><td>1,56</td><td>1,74</td><td>2,06</td><td>2,30</td><td>2,63</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100601"></a>5</td><td>50</td><td>0,3</td><td>1,21</td><td>1,41</td><td>1,69</td><td>1,96</td><td>2,20</td><td>2,55</td><td>2,89</td><td>3,33</td><td colspan="2">3,74</td><td>4,24</td></tr>
<tr><td><a id="p100602"></a>6</td><td>65</td><td>0,3</td><td>1,28</td><td>1,49</td><td>1,78</td><td>2,06</td><td>2,32</td><td>2,69</td><td>3,04</td><td>3,50</td><td colspan="2">3,96</td><td>4,80</td></tr>
<tr><td><a id="p100603"></a>7</td><td>80</td><td>0,4</td><td>1,35</td><td>1,58</td><td>1,89</td><td>2,19</td><td>2,47</td><td>2,86</td><td>3,24</td><td>3,74</td><td colspan="2">4,22</td><td>4,91</td></tr>
<tr><td><a id="p100604"></a>8</td><td>100</td><td>0,5</td><td>1,49</td><td>1,74</td><td>2,11</td><td>2,46</td><td>2,78</td><td>3,25</td><td>3,71</td><td>4,30</td><td colspan="2">4,88</td><td>5,7</td></tr>
<tr><td><a id="p100605"></a>9</td><td>125</td><td>0,6</td><td>1,65</td><td>1,94</td><td>2,37</td><td>2,78</td><td>3,16</td><td>3,73</td><td>4,28</td><td>4,98</td><td colspan="2">5,7</td><td>6,7</td></tr>
<tr><td><a id="p100606"></a>10</td><td>160</td><td>0,8</td><td>1,71</td><td>2,01</td><td>2,46</td><td>2,87</td><td>3,27</td><td>3,85</td><td>4,41</td><td>5,2</td><td colspan="2">5,9</td><td>6,9</td></tr>
<tr><td><a id="p100607"></a>11</td><td>200</td><td>0,8</td><td>1,91</td><td>2,26</td><td>2,79</td><td>3,27</td><td>3,76</td><td>4,46</td><td>5,1</td><td>6,0</td><td colspan="2">6,9</td><td>8,2</td></tr>
<tr><td><a id="p100608"></a>12</td><td>250</td><td>0,9</td><td>2,14</td><td>2,54</td><td>3,16</td><td>3,75</td><td>4,33</td><td>5,2</td><td>6,0</td><td>7,1</td><td colspan="2">8,1</td><td>9,7</td></tr>
<tr><td><a id="p100609"></a>13</td><td>320</td><td>1</td><td>2,45</td><td>2,91</td><td>3,68</td><td>4,39</td><td>5,1</td><td>6,1</td><td>7,1</td><td>8,5</td><td colspan="2">9,8</td><td>11,7</td></tr>
<tr><td><a id="p100610"></a>14</td><td>400</td><td>1</td><td>2,80</td><td>3,34</td><td>4,25</td><td>5,1</td><td>6,0</td><td>7,2</td><td>8,5</td><td>10,1</td><td colspan="2">11,7</td><td>14,1</td></tr>
<tr><td colspan="3"><a id="p100611"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100612"></a>Неполное штучное время<br>Растачивание отверстий<br>Чугуны серые, ковкие и высокопрочные<br>167..264 НВ, Ra 0,8...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 10 (Гексанит-Р), Исмит</td></tr>
<tr><td colspan="4">Карта 12</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100613"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100614"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100615"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100616"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100617"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100618"></a>4</td><td>30</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100619"></a>5</td><td>50</td><td>0,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100620"></a>6</td><td>65</td><td>0,3</td><td>5,4</td><td>6,19</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100621"></a>7</td><td>80</td><td>0,4</td><td>5,72</td><td>6,52</td><td>7,46</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100622"></a>8</td><td>100</td><td>0,5</td><td>6,45</td><td>7,69</td><td>8,85</td><td>10</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100623"></a>9</td><td>125</td><td>0,6</td><td>7,58</td><td>8,76</td><td>10,6</td><td>11,5</td><td>13,8</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100624"></a>10</td><td>160</td><td>0,8</td><td>7,8</td><td>9,01</td><td>10,8</td><td>12,6</td><td>14</td><td>16,1</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100625"></a>11</td><td>200</td><td>0,8</td><td>9,27</td><td>10,7</td><td>12,4</td><td>13,7</td><td>16,2</td><td>19,4</td><td>22</td><td>31,3</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100626"></a>12</td><td>250</td><td>0,9</td><td>11</td><td>12,8</td><td>14,8</td><td>16,9</td><td>19,4</td><td>22,4</td><td>26,3</td><td>37,7</td><td colspan="2">42,4</td><td>49</td></tr>
<tr><td><a id="p100627"></a>13</td><td>320</td><td>1</td><td>13,4</td><td>15,6</td><td>18,2</td><td>20,7</td><td>23,9</td><td>27,7</td><td>32,8</td><td>47,1</td><td colspan="2">53</td><td>61,3</td></tr>
<tr><td><a id="p100628"></a>14</td><td>400</td><td>1</td><td>16,1</td><td>18,9</td><td>22</td><td>25,1</td><td>29</td><td>33,7</td><td>38,4</td><td>56,7</td><td colspan="2">63,8</td><td>73,9</td></tr>
<tr><td colspan="3"><a id="p100629"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="26%"><col width="25%"><col width="26%"><col width="12%"><col width="12%"></colgroup>
<tr><td colspan="3" rowspan="3"><a id="p100630"></a>Неполное штучное время<br>Растачивание отверстий<br>Чугуны серые, ковкие и высокопрочные<br>167..264 НВ, Ra 0,8...0,63, 7 квалитет</td><td colspan="2">Резцы с пластинами<br>Композит 10 (Гексанит-Р), Исмит</td></tr>
<tr><td colspan="2">Карта 12</td></tr>
<tr><td>Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="5"><a id="p100631"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td colspan="5"><a id="p100632"></a>Материал режущего инструмента</td></tr>
<tr><td colspan="2"><a id="p100633"></a>Исмит</td><td colspan="3">Композит 10 (Гексанит-Р)</td></tr>
<tr><td colspan="5"><a id="p100634"></a>Твердость, НВ</td></tr>
<tr><td colspan="2"><a id="p100635"></a>&lt; 224</td><td colspan="3">167...264</td></tr>
<tr><td colspan="5"><a id="p100636"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td><a id="p100637"></a>0,63</td><td>0,8</td><td>0,63</td><td colspan="2">0,8</td></tr>
<tr><td colspan="5"><a id="p100638"></a>Коэффициент Ку</td></tr>
<tr><td><a id="p100639"></a>1,2</td><td>0,8</td><td>1,3</td><td colspan="2">1,0</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100640"></a>Неполное штучное время<br>Растачивание отверстий<br>Чугуны термообработанные и отбеленные<br>HRCэ 41...47, Ra 0,8...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р), Композит 10 (Гексанит-Р)</td></tr>
<tr><td colspan="4">Карта 13</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100641"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100642"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100643"></a>1</td><td>10</td><td>0,1</td><td>0,78</td><td>0,96</td><td>1,08</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100644"></a>2</td><td>15</td><td>0,12</td><td>0,85</td><td>1,01</td><td>1,17</td><td>1,31</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100645"></a>3</td><td>20</td><td>0,15</td><td>0,99</td><td>1,19</td><td>1,40</td><td>1,57</td><td>1,80</td><td>2,05</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100646"></a>4</td><td>30</td><td>0,2</td><td>1,1</td><td>1,32</td><td>1,56</td><td>1,78</td><td>1,98</td><td>2,56</td><td>2,90</td><td>3,34</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100647"></a>5</td><td>50</td><td>0,3</td><td>1,39</td><td>1,72</td><td>2,10</td><td>2,30</td><td>2,78</td><td>3,29</td><td>3,75</td><td>4,37</td><td colspan="2">5,38</td><td>6,34</td></tr>
<tr><td><a id="p100648"></a>6</td><td>65</td><td>0,3</td><td>1,49</td><td>1,86</td><td>2,27</td><td>2,45</td><td>3,03</td><td>3,56</td><td>4,08</td><td>4,76</td><td colspan="2">5,80</td><td>6,84</td></tr>
<tr><td><a id="p100649"></a>7</td><td>80</td><td>0,4</td><td>1,57</td><td>1,97</td><td>2,41</td><td>2,83</td><td>3,22</td><td>3,78</td><td>4,35</td><td>5,08</td><td colspan="2">6,53</td><td>7,77</td></tr>
<tr><td><a id="p100650"></a>8</td><td>100</td><td>0,5</td><td>1,75</td><td>2,19</td><td>2,72</td><td>3,21</td><td>3,67</td><td>4,37</td><td>5,05</td><td>5,92</td><td colspan="2">6,78</td><td>8,06</td></tr>
<tr><td><a id="p100651"></a>9</td><td>125</td><td>0,6</td><td>1,95</td><td>2,49</td><td>3,10</td><td>3,67</td><td>4,24</td><td>5,07</td><td>5,89</td><td>6,94</td><td colspan="2">7,99</td><td>9,53</td></tr>
<tr><td><a id="p100652"></a>10</td><td>160</td><td>0,8</td><td>2,01</td><td>2,55</td><td>3,19</td><td>3,77</td><td>4,46</td><td>6,02</td><td>7,11</td><td>7,8</td><td colspan="2">8,17</td><td>9,72</td></tr>
<tr><td><a id="p100653"></a>11</td><td>200</td><td>0,8</td><td>2,27</td><td>2,93</td><td>3,67</td><td>4,39</td><td>5,10</td><td>6,13</td><td>7,14</td><td>8,46</td><td colspan="2">9,78</td><td>11,7</td></tr>
<tr><td><a id="p100654"></a>12</td><td>250</td><td>0,9</td><td>2,53</td><td>3,29</td><td>4,17</td><td>5,02</td><td>5,85</td><td>7,06</td><td>8,26</td><td>9,83</td><td colspan="2">11,4</td><td>13,7</td></tr>
<tr><td><a id="p100655"></a>13</td><td>320</td><td>1</td><td>3,18</td><td>3,81</td><td>4,90</td><td>5,92</td><td>7,16</td><td>8,54</td><td>9,91</td><td>11,9</td><td colspan="2">13,8</td><td>16,7</td></tr>
<tr><td><a id="p100656"></a>14</td><td>400</td><td>1</td><td>3,28</td><td>4,33</td><td>5,05</td><td>6,27</td><td>7,48</td><td>9,26</td><td>11</td><td>13,9</td><td colspan="2">16,2</td><td>19,6</td></tr>
<tr><td colspan="3"><a id="p100657"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100658"></a>Неполное штучное время<br>Растачивание отверстий<br>Чугуны термообработанные и отбеленные<br>HRCэ 41...47, Ra 0,8...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р), Композит 10 (Гексанит-Р)</td></tr>
<tr><td colspan="4">Карта 13</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100659"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100660"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100661"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100662"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100663"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100664"></a>4</td><td>30</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100665"></a>5</td><td>50</td><td>0,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100666"></a>6</td><td>65</td><td>0,3</td><td>8,82</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100667"></a>7</td><td>80</td><td>0,4</td><td>9,13</td><td>12</td><td>14,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100668"></a>8</td><td>100</td><td>0,5</td><td>10,3</td><td>12,6</td><td>16,9</td><td>19,2</td><td>22,2</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100669"></a>9</td><td>125</td><td>0,6</td><td>10,8</td><td>13,6</td><td>18,3</td><td>20,2</td><td>25,9</td><td>29,8</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100670"></a>10</td><td>160</td><td>0,8</td><td>11</td><td>14,5</td><td>18,9</td><td>21,3</td><td>26,8</td><td>31,2</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100671"></a>11</td><td>200</td><td>0,8</td><td>13,3</td><td>15,6</td><td>19,1</td><td>22,7</td><td>27,3</td><td>35,6</td><td>40,6</td><td>46,3</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100672"></a>12</td><td>250</td><td>0,9</td><td>15,6</td><td>18,3</td><td>21,4</td><td>24,4</td><td>28,2</td><td>36,7</td><td>44,8</td><td>55,7</td><td colspan="2">64,2</td><td>-</td></tr>
<tr><td><a id="p100673"></a>13</td><td>320</td><td>1</td><td>19,1</td><td>22,4</td><td>26,2</td><td>29,9</td><td>34,6</td><td>40,3</td><td>45,9</td><td>67,3</td><td colspan="2">77,6</td><td>89,1</td></tr>
<tr><td><a id="p100674"></a>14</td><td>400</td><td>1</td><td>21,9</td><td>25,9</td><td>30,4</td><td>34,9</td><td>40,5</td><td>47,8</td><td>54,5</td><td>80,9</td><td colspan="2">93,4</td><td>107</td></tr>
<tr><td colspan="3"><a id="p100675"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="26%"><col width="37%"><col width="14%"><col width="12%"><col width="12%"></colgroup>
<tr><td colspan="3" rowspan="3"><a id="p100676"></a>Неполное штучное время<br>Растачивание отверстий<br>Чугуны термообработанные и отбеленные<br>HRCэ 41...47, Ra 0,8...0,63, 7 квалитет</td><td colspan="2">Резцы с пластинами<br>Композит 01 (Эльбор-Р), Композит 10 (Гексанит-Р)</td></tr>
<tr><td colspan="2">Карта 13</td></tr>
<tr><td>Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="5"><a id="p100677"></a>II. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td rowspan="3"><a id="p100678"></a>Материал режущего инструмента</td><td colspan="4">Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td>0,63</td><td colspan="3">0,8</td></tr>
<tr><td colspan="4">Коэффициент Ку</td></tr>
<tr><td><a id="p100679"></a>Композит 10</td><td>1,3</td><td colspan="3">1,0</td></tr>
<tr><td><a id="p100680"></a>Композит 01</td><td>1,2</td><td colspan="3">0,9</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100681"></a>Неполное штучное время<br>Растачивание отверстий<br>Стали низко- и среднеуглеродистые качественные, легированные конструкционные<br>144...279 НВ, Ra 1,6...0,5, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="4">Карта 14</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100682"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100683"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100684"></a>1</td><td>10</td><td>0,1</td><td>0,75</td><td>0,88</td><td>1,01</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100685"></a>2</td><td>15</td><td>0,12</td><td>0,80</td><td>0,92</td><td>1,07</td><td>1,20</td><td>1,32</td><td>1,47</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100686"></a>3</td><td>20</td><td>0,15</td><td>0,85</td><td>0,99</td><td>1,13</td><td>1,25</td><td>1,39</td><td>1,65</td><td>1,71</td><td>2,05</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100687"></a>4</td><td>30</td><td>0,2</td><td>0,97</td><td>1,12</td><td>1,30</td><td>1,47</td><td>1,62</td><td>1,83</td><td>2,04</td><td>2,58</td><td colspan="2">2,89</td><td>3,31</td></tr>
<tr><td><a id="p100688"></a>5</td><td>50</td><td>0,3</td><td>1,14</td><td>1,32</td><td>1,57</td><td>1,80</td><td>2,01</td><td>2,31</td><td>2,59</td><td>2,96</td><td colspan="2">3,33</td><td>3,5</td></tr>
<tr><td><a id="p100689"></a>6</td><td>65</td><td>0,3</td><td>1,18</td><td>1,38</td><td>1,62</td><td>1,85</td><td>2,07</td><td>2,37</td><td>2,65</td><td>3,02</td><td colspan="2">3,38</td><td>3,8</td></tr>
<tr><td><a id="p100690"></a>7</td><td>80</td><td>0,4</td><td>1,23</td><td>1,42</td><td>1,68</td><td>1,91</td><td>2,13</td><td>2,43</td><td>2,72</td><td>3,10</td><td colspan="2">3,46</td><td>3,97</td></tr>
<tr><td><a id="p100691"></a>8</td><td>100</td><td>0,5</td><td>1,34</td><td>1,55</td><td>1,86</td><td>2,13</td><td>2,38</td><td>2,74</td><td>3,09</td><td>3,54</td><td colspan="2">3,97</td><td>4,6</td></tr>
<tr><td><a id="p100692"></a>9</td><td>125</td><td>0,6</td><td>1,47</td><td>1,72</td><td>2,07</td><td>2,38</td><td>2,68</td><td>3,11</td><td>3,53</td><td>4,06</td><td colspan="2">4,6</td><td>5,3</td></tr>
<tr><td><a id="p100693"></a>10</td><td>160</td><td>0,8</td><td>1,65</td><td>1,93</td><td>2,35</td><td>2,73</td><td>3,10</td><td>3,64</td><td>4,15</td><td>4,8</td><td colspan="2">5,5</td><td>6,4</td></tr>
<tr><td><a id="p100694"></a>11</td><td>200</td><td>0,8</td><td>1,83</td><td>2,16</td><td>2,64</td><td>3,09</td><td>3,54</td><td>4,17</td><td>4,8</td><td>5,6</td><td colspan="2">6,4</td><td>7,6</td></tr>
<tr><td><a id="p100695"></a>12</td><td>250</td><td>0,9</td><td>2,04</td><td>2,41</td><td>2,98</td><td>3,51</td><td>4,04</td><td>4,8</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td>8,9</td></tr>
<tr><td><a id="p100696"></a>13</td><td>320</td><td>1</td><td>2,30</td><td>2,73</td><td>3,42</td><td>4,06</td><td>4,7</td><td>5,6</td><td>6,5</td><td>7,7</td><td colspan="2">8,9</td><td>10,6</td></tr>
<tr><td><a id="p100697"></a>14</td><td>400</td><td>1</td><td>2,59</td><td>3,08</td><td>3,88</td><td>4,6</td><td>5,4</td><td>6,5</td><td>7,6</td><td>9,0</td><td colspan="2">10,4</td><td>12,5</td></tr>
<tr><td colspan="3"><a id="p100698"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100699"></a>Неполное штучное время<br>Растачивание отверстий<br>Стали низко- и среднеуглеродистые качественные, легированные конструкционные<br>144...279 НВ, Ra 1,6...0,5, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="4">Карта 14</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100700"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100701"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100702"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100703"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100704"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100705"></a>4</td><td>30</td><td>0,2</td><td>4,42</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100706"></a>5</td><td>50</td><td>0,3</td><td>4,69</td><td>5,07</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100707"></a>6</td><td>65</td><td>0,35</td><td>4,93</td><td>5,11</td><td>6,6</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100708"></a>7</td><td>80</td><td>0,4</td><td>5,11</td><td>5,27</td><td>6,77</td><td>7,37</td><td>8,62</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100709"></a>8</td><td>100</td><td>0,5</td><td>5,44</td><td>5,76</td><td>8,03</td><td>7,68</td><td>10,4</td><td>11,8</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100710"></a>9</td><td>125</td><td>0,6</td><td>6</td><td>6,88</td><td>9,36</td><td>9,8</td><td>12,3</td><td>14,7</td><td>16,6</td><td>33,7</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100711"></a>10</td><td>160</td><td>0,8</td><td>7,25</td><td>8,35</td><td>9,58</td><td>10,8</td><td>12,9</td><td>18</td><td>19,6</td><td>34,1</td><td colspan="2">40,4</td><td>55,5</td></tr>
<tr><td><a id="p100712"></a>11</td><td>200</td><td>0,8</td><td>8,53</td><td>9,86</td><td>11,4</td><td>12,9</td><td>16,1</td><td>19,5</td><td>24,4</td><td>40,3</td><td colspan="2">47,4</td><td>55,8</td></tr>
<tr><td><a id="p100713"></a>12</td><td>250</td><td>0,9</td><td>10</td><td>11,7</td><td>13,5</td><td>15,3</td><td>17,6</td><td>21,8</td><td>26,9</td><td>42,1</td><td colspan="2">58,4</td><td>65,5</td></tr>
<tr><td><a id="p100714"></a>13</td><td>320</td><td>1</td><td>12,1</td><td>14,1</td><td>16,3</td><td>18,6</td><td>21,4</td><td>24,8</td><td>28,1</td><td>53,2</td><td colspan="2">61,3</td><td>70,3</td></tr>
<tr><td><a id="p100715"></a>14</td><td>400</td><td>1</td><td>14,2</td><td>16,6</td><td>19,4</td><td>22,1</td><td>25,4</td><td>29,5</td><td>33,5</td><td>65,9</td><td colspan="2">76,0</td><td>87,2</td></tr>
<tr><td colspan="3"><a id="p100716"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="12%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"><col width="11%"><col width="10%"><col width="12%"><col width="12%"></colgroup>
<tr><td colspan="7" rowspan="3"><a id="p100717"></a>Неполное штучное время<br>Растачивание отверстий<br>Стали низко- и среднеуглеродистые качественные, легированные конструкционные<br>144...279 НВ, Ra 1,6...0,5, 7 квалитет</td><td colspan="2">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="2">Карта 14</td></tr>
<tr><td>Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="9"><a id="p100718"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td colspan="9"><a id="p100719"></a>Обрабатываемый материал</td></tr>
<tr><td colspan="3"><a id="p100720"></a>стали низкоуглеродистые качественные</td><td colspan="3">стали среднеуглеродистые качественные</td><td colspan="3">стали легированные конструкционные</td></tr>
<tr><td colspan="9"><a id="p100721"></a>Твердость обрабатываемого материала, НВ</td></tr>
<tr><td colspan="3"><a id="p100722"></a>144...213</td><td colspan="3">213...279</td><td colspan="3">213...279</td></tr>
<tr><td colspan="9"><a id="p100723"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td><a id="p100724"></a>0,5</td><td>0,8</td><td>1,6</td><td>0,5</td><td>0,8</td><td>1,6</td><td>0,5</td><td>0,8</td><td>1,6</td></tr>
<tr><td colspan="9"><a id="p100725"></a>Коэффициент Ку</td></tr>
<tr><td><a id="p100726"></a>1,1</td><td>0,65</td><td>0,55</td><td>1,2</td><td>0,8</td><td>0,65</td><td>1,5</td><td>1,0</td><td>0,75</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100727"></a>Неполное штучное время<br>Растачивание отверстий<br>Стали термообработанные<br>HRCэ 30...65, Ra 0,8...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р), Композит 10 (Гексанит-Р)</td></tr>
<tr><td colspan="4">Карта 15</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100728"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100729"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100730"></a>1</td><td>10</td><td>0,1</td><td>1,51</td><td>1,84</td><td>2,35</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100731"></a>2</td><td>15</td><td>0,12</td><td>1,74</td><td>2,13</td><td>2,66</td><td>3,21</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100732"></a>3</td><td>20</td><td>0,15</td><td>1,99</td><td>2,43</td><td>3,17</td><td>3,62</td><td>4,24</td><td>4,69</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100733"></a>4</td><td>30</td><td>0,2</td><td>2,04</td><td>2,47</td><td>3,21</td><td>3,80</td><td>4,64</td><td>5,55</td><td>6,33</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100734"></a>5</td><td>50</td><td>0,3</td><td>2,39</td><td>2,89</td><td>3,76</td><td>3,91</td><td>5,45</td><td>6,69</td><td>7,91</td><td>9,53</td><td colspan="2">11,2</td><td>-</td></tr>
<tr><td><a id="p100735"></a>6</td><td>65</td><td>0,3</td><td>2,50</td><td>3,01</td><td>3,90</td><td>4,77</td><td>5,66</td><td>7,22</td><td>8,11</td><td>9,8</td><td colspan="2">11,8</td><td>13,8</td></tr>
<tr><td><a id="p100736"></a>7</td><td>80</td><td>0,3</td><td>2,85</td><td>3,47</td><td>4,55</td><td>5,61</td><td>6,62</td><td>7,87</td><td>8,51</td><td>10,9</td><td colspan="2">12,4</td><td>14,8</td></tr>
<tr><td><a id="p100737"></a>8</td><td>100</td><td>0,4</td><td>2,91</td><td>3,51</td><td>4,60</td><td>5,65</td><td>6,69</td><td>8,22</td><td>9,75</td><td>11,8</td><td colspan="2">13,8</td><td>16,7</td></tr>
<tr><td><a id="p100738"></a>9</td><td>125</td><td>0,4</td><td>3,39</td><td>4,12</td><td>5,42</td><td>6,69</td><td>7,95</td><td>9,82</td><td>11,7</td><td>14,1</td><td colspan="2">16,6</td><td>20,2</td></tr>
<tr><td><a id="p100739"></a>10</td><td>160</td><td>0,5</td><td>3,92</td><td>4,77</td><td>6,30</td><td>7,79</td><td>9,28</td><td>11,5</td><td>13,7</td><td>17,5</td><td colspan="2">19,5</td><td>23,7</td></tr>
<tr><td><a id="p100740"></a>11</td><td>200</td><td>0,5</td><td>4,06</td><td>4,94</td><td>6,57</td><td>8,15</td><td>9,72</td><td>12,1</td><td>14,4</td><td>16,6</td><td colspan="2">20,5</td><td>25,1</td></tr>
<tr><td><a id="p100741"></a>12</td><td>250</td><td>0,5</td><td>4,56</td><td>5,56</td><td>7,40</td><td>9,20</td><td>11,0</td><td>13,6</td><td>16,3</td><td>19,8</td><td colspan="2">23,2</td><td>28,4</td></tr>
<tr><td><a id="p100742"></a>13</td><td>320</td><td>0,6</td><td>5,53</td><td>6,76</td><td>9,07</td><td>11,3</td><td>13,6</td><td>16,9</td><td>20,2</td><td>24,7</td><td colspan="2">29,1</td><td>35,6</td></tr>
<tr><td><a id="p100743"></a>14</td><td>400</td><td>0,6</td><td>6,37</td><td>7,80</td><td>10,5</td><td>13,2</td><td>15,8</td><td>19,7</td><td>23,6</td><td>28,9</td><td colspan="2">34,0</td><td>41,8</td></tr>
<tr><td colspan="3"><a id="p100744"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100745"></a>Неполное штучное время<br>Растачивание отверстий<br>Стали термообработанные<br>HRCэ 30...65, Ra 0,8...0,63, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р), Композит 10 (Гексанит-Р)</td></tr>
<tr><td colspan="4">Карта 15</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100746"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100747"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100748"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100749"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100750"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100751"></a>4</td><td>30</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100752"></a>5</td><td>50</td><td>0,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100753"></a>6</td><td>65</td><td>0,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100754"></a>7</td><td>80</td><td>0,3</td><td>15,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100755"></a>8</td><td>100</td><td>0,4</td><td>19,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100756"></a>9</td><td>125</td><td>0,4</td><td>23,2</td><td>27,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100757"></a>10</td><td>160</td><td>0,5</td><td>27,3</td><td>32,3</td><td>38</td><td>43,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100758"></a>11</td><td>200</td><td>0,5</td><td>28,9</td><td>34,2</td><td>40,3</td><td>46,4</td><td>50,8</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100759"></a>12</td><td>250</td><td>0,5</td><td>32,8</td><td>38,8</td><td>45,7</td><td>52,6</td><td>61,2</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100760"></a>13</td><td>320</td><td>0,6</td><td>41,1</td><td>48,7</td><td>57,5</td><td>66,2</td><td>77</td><td>90,1</td><td>103</td><td>118</td><td colspan="2">133</td><td>-</td></tr>
<tr><td><a id="p100761"></a>14</td><td>400</td><td>0,6</td><td>48,2</td><td>57,3</td><td>67,6</td><td>77,8</td><td>90,7</td><td>106</td><td>121</td><td>139</td><td colspan="2">157</td><td>170</td></tr>
<tr><td colspan="3"><a id="p100762"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="27%"><col width="12%"><col width="12%"><col width="12%"><col width="13%"><col width="12%"><col width="12%"></colgroup>
<tr><td colspan="5" rowspan="3"><a id="p100763"></a>Неполное штучное время<br>Растачивание отверстий<br>Стали термообработанные<br>HRCэ 30...65, Ra 0,8...0,63, 7 квалитет</td><td colspan="2">Резцы с пластинами<br>Композит 01 (Эльбор-Р), Композит 10 (Гексанит-Р)</td></tr>
<tr><td colspan="2">Карта 15</td></tr>
<tr><td>Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="7"><a id="p100764"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td rowspan="5"><a id="p100765"></a>Материал режущего инструмента</td><td colspan="6">Твердость обрабатываемого материала, HRCэ</td></tr>
<tr><td colspan="2">30...35</td><td colspan="2">36...55</td><td colspan="2">56...65</td></tr>
<tr><td colspan="6">Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td>0,63</td><td>0,8</td><td>0,63</td><td>0,8</td><td>0,63</td><td>0,8</td></tr>
<tr><td colspan="6">Коэффициент Ку</td></tr>
<tr><td><a id="p100766"></a>Композит 01</td><td>0,8</td><td>0,4</td><td>1,0</td><td>0,5</td><td>1,35</td><td>0,65</td></tr>
<tr><td><a id="p100767"></a>Композит 10</td><td>-</td><td>-</td><td>1,15</td><td>0,6</td><td>1,4</td><td>0,7</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100768"></a>Неполное штучное время<br>Растачивание отверстий<br>Стали термообработанные<br>HRCэ 35...65, Ra 1,6...0,32, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Исмит</td></tr>
<tr><td colspan="4">Карта 16</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100769"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100770"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100771"></a>1</td><td>10</td><td>0,1</td><td>1,08</td><td>1,30</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100772"></a>2</td><td>15</td><td>0,12</td><td>1,35</td><td>1,63</td><td>2,05</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100773"></a>3</td><td>20</td><td>0,15</td><td>1,49</td><td>1,78</td><td>2,24</td><td>2,68</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100774"></a>4</td><td>30</td><td>0,2</td><td>1,88</td><td>2,26</td><td>2,90</td><td>3,11</td><td>4,13</td><td>5,03</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100775"></a>5</td><td>50</td><td>0,2</td><td>2,17</td><td>2,61</td><td>3,17</td><td>3,52</td><td>4,83</td><td>5,91</td><td>6,96</td><td>7,36</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100776"></a>6</td><td>65</td><td>0,2</td><td>2,30</td><td>2,76</td><td>3,57</td><td>4,32</td><td>5,06</td><td>6,16</td><td>7,50</td><td>8,2</td><td colspan="2">8,5</td><td>-</td></tr>
<tr><td><a id="p100777"></a>7</td><td>80</td><td>0,2</td><td>2,56</td><td>3,09</td><td>4,03</td><td>4,94</td><td>5,84</td><td>7,17</td><td>8,00</td><td>8,70</td><td colspan="2">9,1</td><td>12,2</td></tr>
<tr><td><a id="p100778"></a>8</td><td>100</td><td>0,2</td><td>2,67</td><td>3,21</td><td>4,17</td><td>5,10</td><td>6,02</td><td>7,37</td><td>8,71</td><td>10,5</td><td colspan="2">12,2</td><td>14,9</td></tr>
<tr><td><a id="p100779"></a>9</td><td>125</td><td>0,25</td><td>3,07</td><td>3,71</td><td>4,84</td><td>5,93</td><td>7,01</td><td>8,61</td><td>9,4</td><td>11,5</td><td colspan="2">12,7</td><td>15,9</td></tr>
<tr><td><a id="p100780"></a>10</td><td>160</td><td>0,25</td><td>3,09</td><td>3,74</td><td>4,95</td><td>6,02</td><td>7,12</td><td>8,77</td><td>10,2</td><td>12,3</td><td colspan="2">14,4</td><td>17,5</td></tr>
<tr><td><a id="p100781"></a>11</td><td>200</td><td>0,25</td><td>3,55</td><td>4,31</td><td>5,66</td><td>6,97</td><td>8,28</td><td>10,2</td><td>12,1</td><td>14,6</td><td colspan="2">17,2</td><td>20,9</td></tr>
<tr><td><a id="p100782"></a>12</td><td>250</td><td>0,25</td><td>4,12</td><td>5,00</td><td>6,62</td><td>8,19</td><td>9,76</td><td>12,1</td><td>14,4</td><td>17,4</td><td colspan="2">20,5</td><td>25,0</td></tr>
<tr><td><a id="p100783"></a>13</td><td>320</td><td>0,25</td><td>4,95</td><td>6,05</td><td>8,06</td><td>10,0</td><td>12,0</td><td>14,9</td><td>17,8</td><td>21,6</td><td colspan="2">25,5</td><td>31,2</td></tr>
<tr><td><a id="p100784"></a>14</td><td>400</td><td>0,35</td><td>5,76</td><td>7,04</td><td>9,43</td><td>11,8</td><td>14,1</td><td>17,6</td><td>21,1</td><td>25,7</td><td colspan="2">30,2</td><td>37,0</td></tr>
<tr><td colspan="3"><a id="p100785"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100786"></a>Неполное штучное время<br>Растачивание отверстий<br>Стали термообработанные<br>HRCэ 35...65, Ra 1,6...0,32, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Исмит</td></tr>
<tr><td colspan="4">Карта 16</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100787"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100788"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100789"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100790"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100791"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100792"></a>4</td><td>30</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100793"></a>5</td><td>50</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100794"></a>6</td><td>65</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100795"></a>7</td><td>80</td><td>0,2</td><td>14</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100796"></a>8</td><td>100</td><td>0,2</td><td>17</td><td>20,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100797"></a>9</td><td>125</td><td>0,25</td><td>18,5</td><td>22,2</td><td>27,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100798"></a>10</td><td>160</td><td>0,25</td><td>20</td><td>24,6</td><td>28,5</td><td>31,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100799"></a>11</td><td>200</td><td>0,25</td><td>24</td><td>28,4</td><td>33,4</td><td>38,3</td><td>44,5</td><td>51,9</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100800"></a>12</td><td>250</td><td>0,25</td><td>28,7</td><td>34</td><td>40</td><td>46</td><td>53,5</td><td>62,4</td><td>71,3</td><td>81,7</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100801"></a>13</td><td>320</td><td>0,25</td><td>35,9</td><td>42,6</td><td>50,1</td><td>57,7</td><td>67,1</td><td>78,4</td><td>89,7</td><td>103</td><td colspan="2">116</td><td>-</td></tr>
<tr><td><a id="p100802"></a>14</td><td>400</td><td>0,35</td><td>42,8</td><td>50,7</td><td>59,8</td><td>68,8</td><td>80,1</td><td>93,7</td><td>107</td><td>123</td><td colspan="2">139</td><td>150</td></tr>
<tr><td colspan="3"><a id="p100803"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="24%"><col width="25%"><col width="27%"><col width="12%"><col width="12%"></colgroup>
<tr><td colspan="3" rowspan="3"><a id="p100804"></a>Неполное штучное время<br>Растачивание отверстий<br>Стали термообработанные<br>HRCэ 35...65, Ra 1,6...0,32, 7 квалитет</td><td colspan="2">Резцы с пластинами<br>Исмит</td></tr>
<tr><td colspan="2">Карта 16</td></tr>
<tr><td>Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="5"><a id="p100805"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td colspan="5"><a id="p100806"></a>Твердость обрабатываемого материала, HRCэ</td></tr>
<tr><td colspan="2"><a id="p100807"></a>35...50</td><td colspan="3">51...65</td></tr>
<tr><td colspan="5"><a id="p100808"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td><a id="p100809"></a>0,63</td><td>1,6</td><td>0,32</td><td colspan="2">0,8</td></tr>
<tr><td colspan="5"><a id="p100810"></a>Коэффициент Ку</td></tr>
<tr><td><a id="p100811"></a>1,0</td><td>0,75</td><td>2,1</td><td colspan="2">1,3</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100812"></a>Неполное штучное время<br>Растачивание отверстий<br>Бронзы, латуни<br>&lt; 137...&gt;= 137 НВ, Ra 0,8...0,32, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="4">Карта 17</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100813"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100814"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100815"></a>1</td><td>10</td><td>0,1</td><td>0,82</td><td>0,97</td><td>1,12</td><td>1,29</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100816"></a>2</td><td>15</td><td>0,12</td><td>0,87</td><td>1,03</td><td>1,21</td><td>1,38</td><td>1,53</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100817"></a>3</td><td>20</td><td>0,15</td><td>1,07</td><td>1,26</td><td>1,51</td><td>1,74</td><td>1,98</td><td>2,30</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100818"></a>4</td><td>30</td><td>0,2</td><td>1,13</td><td>1,32</td><td>1,58</td><td>1,83</td><td>2,06</td><td>2,39</td><td>2,71</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100819"></a>5</td><td>50</td><td>0,2</td><td>1,21</td><td>1,41</td><td>1,69</td><td>1,96</td><td>2,20</td><td>2,55</td><td>2,89</td><td>3,33</td><td colspan="2">3,5</td><td>3,8</td></tr>
<tr><td><a id="p100820"></a>6</td><td>65</td><td>0,2</td><td>1,26</td><td>1,47</td><td>1,75</td><td>2,02</td><td>2,27</td><td>2,62</td><td>2,96</td><td>3,4</td><td colspan="2">3,7</td><td>4,1</td></tr>
<tr><td><a id="p100821"></a>7</td><td>80</td><td>0,2</td><td>1,31</td><td>1,52</td><td>1,81</td><td>2,09</td><td>2,34</td><td>2,69</td><td>3,04</td><td>3,50</td><td colspan="2">3,9</td><td>4,4</td></tr>
<tr><td><a id="p100822"></a>8</td><td>100</td><td>0,2</td><td>1,35</td><td>1,56</td><td>1,86</td><td>2,14</td><td>2,39</td><td>2,75</td><td>3,11</td><td>3,6</td><td colspan="2">4,0</td><td>4,6</td></tr>
<tr><td><a id="p100823"></a>9</td><td>125</td><td>0,25</td><td>1,43</td><td>1,68</td><td>1,98</td><td>2,30</td><td>2,56</td><td>2,98</td><td>3,3</td><td>3,8</td><td colspan="2">4,3</td><td>4,9</td></tr>
<tr><td><a id="p100824"></a>10</td><td>160</td><td>0,25</td><td>1,52</td><td>1,77</td><td>2,12</td><td>2,44</td><td>2,74</td><td>3,2</td><td>3,6</td><td>4,1</td><td colspan="2">4,7</td><td>5,4</td></tr>
<tr><td><a id="p100825"></a>11</td><td>200</td><td>0,25</td><td>1,64</td><td>1,92</td><td>2,32</td><td>2,67</td><td>3,02</td><td>3,5</td><td>4,0</td><td>4,6</td><td colspan="2">5,2</td><td>6,1</td></tr>
<tr><td><a id="p100826"></a>12</td><td>250</td><td>0,25</td><td>1,81</td><td>2,12</td><td>2,57</td><td>2,99</td><td>3,4</td><td>4,0</td><td>4,5</td><td>5,3</td><td colspan="2">6,0</td><td>7,1</td></tr>
<tr><td><a id="p100827"></a>13</td><td>320</td><td>0,25</td><td>1,86</td><td>2,18</td><td>2,65</td><td>3,1</td><td>3,5</td><td>4,1</td><td>4,7</td><td>5,4</td><td colspan="2">6,1</td><td>7,2</td></tr>
<tr><td><a id="p100828"></a>14</td><td>400</td><td>0,35</td><td>2,07</td><td>2,42</td><td>3,0</td><td>3,5</td><td>4,0</td><td>4,7</td><td>5,4</td><td>6,3</td><td colspan="2">7,1</td><td>8,4</td></tr>
<tr><td colspan="3"><a id="p100829"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100830"></a>Неполное штучное время<br>Растачивание отверстий<br>Бронзы, латуни<br>&lt; 137...&gt;= 137 НВ, Ra 0,8...0,32, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="4">Карта 17</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 3</td></tr>
<tr><td colspan="14"><a id="p100831"></a>I. Растачивание отверстий</td></tr>
<tr><td rowspan="3"><a id="p100832"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100833"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100834"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100835"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100836"></a>4</td><td>30</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100837"></a>5</td><td>50</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100838"></a>6</td><td>65</td><td>0,2</td><td>5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100839"></a>7</td><td>80</td><td>0,2</td><td>5,09</td><td>5,81</td><td>6,63</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100840"></a>8</td><td>100</td><td>0,2</td><td>5,17</td><td>5,89</td><td>6,72</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100841"></a>9</td><td>125</td><td>0,25</td><td>5,99</td><td>6,67</td><td>7,42</td><td>7,18</td><td>8,11</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100842"></a>10</td><td>160</td><td>0,25</td><td>6,07</td><td>6,95</td><td>7,91</td><td>8,91</td><td>10,1</td><td>11,6</td><td>13</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100843"></a>11</td><td>200</td><td>0,25</td><td>6,84</td><td>7,85</td><td>8,99</td><td>10,1</td><td>11,5</td><td>13,2</td><td>14,9</td><td>16,8</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100844"></a>12</td><td>250</td><td>0,25</td><td>7,95</td><td>9,16</td><td>10,5</td><td>11,9</td><td>13,6</td><td>15,6</td><td>17,6</td><td>19,9</td><td colspan="2">22,3</td><td>-</td></tr>
<tr><td><a id="p100845"></a>13</td><td>320</td><td>0,25</td><td>8,09</td><td>9,31</td><td>10,7</td><td>12,1</td><td>13,8</td><td>15,8</td><td>17,8</td><td>20,2</td><td colspan="2">22,5</td><td>25,8</td></tr>
<tr><td><a id="p100846"></a>14</td><td>400</td><td>0,35</td><td>9,5</td><td>11</td><td>12,7</td><td>14,3</td><td>16,4</td><td>18,9</td><td>21,3</td><td>24,2</td><td colspan="2">27,1</td><td>31,1</td></tr>
<tr><td colspan="3"><a id="p100847"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="34%"><col width="33%"><col width="10%"><col width="12%"><col width="12%"></colgroup>
<tr><td colspan="3" rowspan="3"><a id="p100848"></a>Неполное штучное время<br>Растачивание отверстий<br>Бронзы, латуни<br>&lt; 137...&gt;= 137 НВ, Ra 0,8...0,32, 7 квалитет</td><td colspan="2">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="2">Карта 17</td></tr>
<tr><td>Лист 3</td><td>Листов 3</td></tr>
<tr><td colspan="5"><a id="p100849"></a>III. Поправочные коэффициенты на время обработки для измененных условий работы</td></tr>
<tr><td rowspan="3"><a id="p100850"></a>Твердость обрабатываемого материала, НВ</td><td colspan="4">Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td>0,32</td><td colspan="3">0,8</td></tr>
<tr><td colspan="4">Коэффициент Ку</td></tr>
<tr><td><a id="p100851"></a>&gt;= 137</td><td>1,0</td><td colspan="3">0,7</td></tr>
<tr><td><a id="p100852"></a>&lt; 137</td><td>0,8</td><td colspan="3">0,6</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100853"></a>Неполное штучное время<br>Растачивание отверстий<br>Чугуны серые, ковкие, высокопрочные и термообработанные<br>&lt; 224 НВ, HRCэ 41...47, Ra 0,8...0,63</td><td colspan="4">Резцы с пластинами<br>Исмит</td></tr>
<tr><td colspan="4">Карта 18</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p100854"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100855"></a>1</td><td>10</td><td>0,1</td><td>0,85</td><td>0,99</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100856"></a>2</td><td>15</td><td>0,12</td><td>0,9</td><td>1,1</td><td>1,20</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100857"></a>3</td><td>20</td><td>0,15</td><td>10,9</td><td>1,34</td><td>1,61</td><td>1,83</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100858"></a>4</td><td>30</td><td>0,2</td><td>1,16</td><td>1,41</td><td>1,68</td><td>1,93</td><td>2,17</td><td>2,51</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100859"></a>5</td><td>50</td><td>0,2</td><td>1,23</td><td>1,51</td><td>1,79</td><td>2,07</td><td>3,32</td><td>2,68</td><td>3,03</td><td>3,47</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100860"></a>6</td><td>65</td><td>0,2</td><td>1,31</td><td>1,64</td><td>1,90</td><td>2,19</td><td>2,46</td><td>2,84</td><td>3,20</td><td>3,67</td><td colspan="2">4,15</td><td>4,81</td></tr>
<tr><td><a id="p100861"></a>7</td><td>80</td><td>0,2</td><td>1,34</td><td>1,65</td><td>1,95</td><td>2,21</td><td>2,48</td><td>2,86</td><td>3,22</td><td>3,69</td><td colspan="2">4,20</td><td>4,83</td></tr>
<tr><td><a id="p100862"></a>8</td><td>100</td><td>0,2</td><td>1,58</td><td>1,95</td><td>2,38</td><td>2,77</td><td>3,15</td><td>3,69</td><td>4,54</td><td>4,90</td><td colspan="2">5,57</td><td>6,56</td></tr>
<tr><td><a id="p100863"></a>9</td><td>125</td><td>0,25</td><td>1,60</td><td>1,98</td><td>2,40</td><td>2,79</td><td>3,18</td><td>3,71</td><td>4,56</td><td>4,93</td><td colspan="2">5,58</td><td>6,58</td></tr>
<tr><td><a id="p100864"></a>10</td><td>160</td><td>0,25</td><td>1,64</td><td>2,01</td><td>2,42</td><td>2,90</td><td>3,20</td><td>3,72</td><td>4,58</td><td>4,95</td><td colspan="2">5,60</td><td>6,61</td></tr>
<tr><td><a id="p100865"></a>11</td><td>200</td><td>0,25</td><td>1,8</td><td>2,24</td><td>2,73</td><td>3,11</td><td>3,60</td><td>4,21</td><td>4,83</td><td>5,60</td><td colspan="2">6,41</td><td>7,49</td></tr>
<tr><td><a id="p100866"></a>12</td><td>250</td><td>0,25</td><td>1,99</td><td>2,49</td><td>3,06</td><td>3,59</td><td>4,10</td><td>4,86</td><td>5,56</td><td>6,49</td><td colspan="2">7,43</td><td>8,78</td></tr>
<tr><td><a id="p100867"></a>13</td><td>320</td><td>0,25</td><td>2,24</td><td>2,90</td><td>3,54</td><td>4,18</td><td>4,82</td><td>5,73</td><td>6,63</td><td>7,81</td><td colspan="2">8,97</td><td>10,7</td></tr>
<tr><td><a id="p100868"></a>14</td><td>400</td><td>0,35</td><td>2,52</td><td>3,22</td><td>4,05</td><td>4,83</td><td>5,59</td><td>6,71</td><td>7,79</td><td>9,24</td><td colspan="2">10,7</td><td>12,7</td></tr>
<tr><td colspan="3"><a id="p100869"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100870"></a>Неполное штучное время<br>Растачивание отверстий<br>Чугуны серые, ковкие, высокопрочные и термообработанные<br>&lt; 224 НВ, HRCэ 41...47, Ra 0,8...0,63</td><td colspan="4">Резцы с пластинами<br>Исмит</td></tr>
<tr><td colspan="4">Карта 18</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p100871"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100872"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100873"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100874"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100875"></a>4</td><td>30</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100876"></a>5</td><td>50</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100877"></a>6</td><td>65</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100878"></a>7</td><td>80</td><td>0,2</td><td>5,20</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100879"></a>8</td><td>100</td><td>0,2</td><td>7,38</td><td>8,42</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100880"></a>9</td><td>125</td><td>0,25</td><td>7,40</td><td>8,45</td><td>9,27</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100881"></a>10</td><td>160</td><td>0,25</td><td>7,43</td><td>8,47</td><td>9,35</td><td>10,7</td><td>12,2</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100882"></a>11</td><td>200</td><td>0,25</td><td>8,44</td><td>9,72</td><td>11,2</td><td>12,6</td><td>14,4</td><td>16,6</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100883"></a>12</td><td>250</td><td>0,25</td><td>9,97</td><td>11,5</td><td>13,2</td><td>15,3</td><td>17,2</td><td>19,8</td><td>22,4</td><td>25,4</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100884"></a>13</td><td>320</td><td>0,25</td><td>12,1</td><td>14,1</td><td>16,3</td><td>18,5</td><td>21,3</td><td>24,6</td><td>27,9</td><td>30,1</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100885"></a>14</td><td>400</td><td>0,35</td><td>14,5</td><td>16,9</td><td>19,7</td><td>22,4</td><td>25,8</td><td>29,9</td><td>35,2</td><td>38,6</td><td colspan="2">44,3</td><td>50,7</td></tr>
<tr><td colspan="3"><a id="p100886"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>


<a id="p100887"></a>*Примечание.* Нормативное время рассчитано при шероховатости Ra 0,63, для шероховатости Ra 0,8 время следует умножать на коэффициент 0,75.


<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100888"></a>Неполное штучное время<br>Растачивание отверстий<br>Бронзы, латуни<br>39...49 НВ, Ra <sub>0</sub>,8...0,32</td><td colspan="4">Резцы с пластинами<br>Синтетический алмаз</td></tr>
<tr><td colspan="4">Карта 19</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p100889"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100890"></a>1</td><td>10</td><td>0,1</td><td>1,10</td><td>1,22</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100891"></a>2</td><td>15</td><td>0,12</td><td>1,20</td><td>1,44</td><td>1,78</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100892"></a>3</td><td>20</td><td>0,15</td><td>1,29</td><td>1,54</td><td>1,90</td><td>2,24</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100893"></a>4</td><td>30</td><td>0,15</td><td>1,48</td><td>1,75</td><td>2,19</td><td>2,61</td><td>3,02</td><td>3,61</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100894"></a>5</td><td>50</td><td>0,2</td><td>1,66</td><td>1,89</td><td>2,34</td><td>2,62</td><td>3,12</td><td>3,81</td><td>4,00</td><td>5,00</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100895"></a>6</td><td>65</td><td>0,25</td><td>1,80</td><td>2,13</td><td>2,67</td><td>2,78</td><td>3,20</td><td>3,90</td><td>4,40</td><td>5,2</td><td colspan="2">6,0</td><td>-</td></tr>
<tr><td><a id="p100896"></a>7</td><td>80</td><td>0,25</td><td>1,95</td><td>2,33</td><td>2,98</td><td>3,19</td><td>3,69</td><td>4,42</td><td>5,13</td><td>6,08</td><td colspan="2">7,0</td><td>8,4</td></tr>
<tr><td><a id="p100897"></a>8</td><td>100</td><td>0,25</td><td>2,03</td><td>2,41</td><td>3,05</td><td>3,67</td><td>4,26</td><td>5,14</td><td>6,00</td><td>7,1</td><td colspan="2">8,2</td><td>9,9</td></tr>
<tr><td><a id="p100898"></a>9</td><td>125</td><td>0,3</td><td>2,12</td><td>2,52</td><td>3,18</td><td>3,80</td><td>4,40</td><td>5,29</td><td>6,2</td><td>7,3</td><td colspan="2">8,4</td><td>10,1</td></tr>
<tr><td><a id="p100899"></a>10</td><td>160</td><td>0,3</td><td>2,30</td><td>2,76</td><td>3,52</td><td>4,25</td><td>4,96</td><td>6,02</td><td>7,1</td><td>8,4</td><td colspan="2">9,8</td><td>11,8</td></tr>
<tr><td><a id="p100900"></a>11</td><td>200</td><td>0,3</td><td>2,41</td><td>2,88</td><td>3,65</td><td>4,39</td><td>5,12</td><td>6,2</td><td>7,2</td><td>8,6</td><td colspan="2">10,0</td><td>12,0</td></tr>
<tr><td><a id="p100901"></a>12</td><td>250</td><td>0,3</td><td>2,76</td><td>3,31</td><td>4,24</td><td>5,13</td><td>6,02</td><td>7,3</td><td>8,6</td><td>10,3</td><td colspan="2">12,0</td><td>14,4</td></tr>
<tr><td><a id="p100902"></a>13</td><td>320</td><td>0,3</td><td>3,18</td><td>3,84</td><td>4,97</td><td>6,1</td><td>7,1</td><td>8,7</td><td>10,3</td><td>12,4</td><td colspan="2">14,4</td><td>17,4</td></tr>
<tr><td><a id="p100903"></a>14</td><td>400</td><td>0,3</td><td>3,69</td><td>4,45</td><td>5,81</td><td>7,1</td><td>8,4</td><td>10,4</td><td>12,2</td><td>14,8</td><td colspan="2">17,3</td><td>21,0</td></tr>
<tr><td colspan="3"><a id="p100904"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100905"></a>Неполное штучное время<br>Растачивание отверстий<br>Бронзы, латуни<br>39...49 НВ, Ra 0,8...0,32</td><td colspan="4">Резцы с пластинами<br>Синтетический алмаз</td></tr>
<tr><td colspan="4">Карта 19</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p100906"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100907"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100908"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100909"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100910"></a>4</td><td>30</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100911"></a>5</td><td>50</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100912"></a>6</td><td>65</td><td>0,25</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100913"></a>7</td><td>80</td><td>0,25</td><td>9,52</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100914"></a>8</td><td>100</td><td>0,25</td><td>11,3</td><td>13,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100915"></a>9</td><td>125</td><td>0,3</td><td>11,5</td><td>13,4</td><td>15,6</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100916"></a>10</td><td>160</td><td>0,3</td><td>13,5</td><td>15,8</td><td>18,4</td><td>17,8</td><td>20,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100917"></a>11</td><td>200</td><td>0,3</td><td>13,7</td><td>16,1</td><td>18,7</td><td>21,4</td><td>24,7</td><td>28,7</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100918"></a>12</td><td>250</td><td>0,3</td><td>16,5</td><td>19,4</td><td>22,7</td><td>25,9</td><td>30</td><td>34,9</td><td>39,7</td><td>45,4</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100919"></a>13</td><td>320</td><td>0,3</td><td>20</td><td>23,6</td><td>27,6</td><td>31,6</td><td>36,6</td><td>42,6</td><td>48,6</td><td>55,6</td><td colspan="2">62,6</td><td>-</td></tr>
<tr><td><a id="p100920"></a>14</td><td>400</td><td>0,3</td><td>24,1</td><td>28,4</td><td>33,4</td><td>38,3</td><td>44,4</td><td>51,7</td><td>59,1</td><td>67,6</td><td colspan="2">76,2</td><td>88,3</td></tr>
<tr><td colspan="3"><a id="p100921"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>


<a id="p100922"></a>*Примечание.* Нормативное время рассчитано при шероховатости Ra 0,32. Для шероховатости Ra 0,8 время следует умножать на коэффициент 0,75.


<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100923"></a>Неполное штучное время<br>Растачивание отверстий<br>Латуни<br>52...137 НВ, Ra 0,2...0,1</td><td colspan="4">Резцы с пластинами<br>Натуральный алмаз</td></tr>
<tr><td colspan="4">Карта 20</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p100924"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100925"></a>1</td><td>10</td><td>0,1</td><td>1,04</td><td>1,25</td><td>1,52</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100926"></a>2</td><td>15</td><td>0,12</td><td>1,09</td><td>1,30</td><td>1,59</td><td>1,87</td><td>2,13</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100927"></a>3</td><td>20</td><td>0,15</td><td>1,25</td><td>1,48</td><td>1,83</td><td>2,15</td><td>2,48</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100928"></a>4</td><td>30</td><td>0,15</td><td>1,35</td><td>1,59</td><td>1,95</td><td>2,28</td><td>2,60</td><td>3,06</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100929"></a>5</td><td>50</td><td>0,2</td><td>1,54</td><td>1,82</td><td>2,24</td><td>2,65</td><td>3,07</td><td>3,20</td><td>3,50</td><td>4,09</td><td colspan="2">4,67</td><td>-</td></tr>
<tr><td><a id="p100930"></a>6</td><td>65</td><td>0,25</td><td>1,57</td><td>1,87</td><td>2,35</td><td>2,75</td><td>3,15</td><td>3,72</td><td>4,15</td><td>4,9</td><td colspan="2">5,6</td><td>-</td></tr>
<tr><td><a id="p100931"></a>7</td><td>80</td><td>0,25</td><td>1,60</td><td>1,89</td><td>2,45</td><td>2,81</td><td>3,24</td><td>3,93</td><td>4,29</td><td>5,04</td><td colspan="2">5,8</td><td>6,8</td></tr>
<tr><td><a id="p100932"></a>8</td><td>100</td><td>0,25</td><td>1,79</td><td>2,11</td><td>2,63</td><td>3,12</td><td>3,60</td><td>4,29</td><td>4,97</td><td>5,9</td><td colspan="2">6,7</td><td>8,0</td></tr>
<tr><td><a id="p100933"></a>9</td><td>125</td><td>0,3</td><td>2,01</td><td>2,40</td><td>3,00</td><td>3,57</td><td>4,12</td><td>4,93</td><td>5,7</td><td>6,8</td><td colspan="2">7,8</td><td>9,3</td></tr>
<tr><td><a id="p100934"></a>10</td><td>160</td><td>0,3</td><td>2,02</td><td>2,40</td><td>3,20</td><td>3,60</td><td>4,17</td><td>5,01</td><td>5,8</td><td>6,9</td><td colspan="2">8,0</td><td>9,5</td></tr>
<tr><td><a id="p100935"></a>11</td><td>200</td><td>0,3</td><td>2,29</td><td>2,73</td><td>3,44</td><td>4,12</td><td>4,79</td><td>5,8</td><td>6,7</td><td>8,0</td><td colspan="2">9,2</td><td>11,1</td></tr>
<tr><td><a id="p100936"></a>12</td><td>250</td><td>0,3</td><td>2,54</td><td>3,03</td><td>3,85</td><td>4,63</td><td>5,41</td><td>6,5</td><td>7,6</td><td>9,1</td><td colspan="2">10,6</td><td>12,7</td></tr>
<tr><td><a id="p100937"></a>13</td><td>320</td><td>0,3</td><td>2,92</td><td>3,50</td><td>4,50</td><td>5,4</td><td>6,4</td><td>7,8</td><td>9,1</td><td>10,9</td><td colspan="2">12,7</td><td>15,4</td></tr>
<tr><td><a id="p100938"></a>14</td><td>400</td><td>0,3</td><td>3,35</td><td>4,03</td><td>5,22</td><td>6,4</td><td>7,5</td><td>9,2</td><td>10,8</td><td>13,0</td><td colspan="2">15,2</td><td>18,4</td></tr>
<tr><td colspan="3"><a id="p100939"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100940"></a>Неполное штучное время<br>Растачивание отверстий<br>Латуни<br>52...137 НВ, Ra 0,2...0,1</td><td colspan="4">Резцы с пластинами<br>Натуральный алмаз</td></tr>
<tr><td colspan="4">Карта 20</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p100941"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100942"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100943"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100944"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100945"></a>4</td><td>30</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100946"></a>5</td><td>50</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100947"></a>6</td><td>65</td><td>0,25</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100948"></a>7</td><td>80</td><td>0,25</td><td>7,74</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100949"></a>8</td><td>100</td><td>0,25</td><td>9,12</td><td>10,6</td><td>12,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100950"></a>9</td><td>125</td><td>0,3</td><td>10,6</td><td>12,3</td><td>14,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100951"></a>10</td><td>160</td><td>0,3</td><td>10,9</td><td>12,6</td><td>14,8</td><td>16,3</td><td>18,8</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100952"></a>11</td><td>200</td><td>0,3</td><td>12,6</td><td>14,8</td><td>17,2</td><td>19,6</td><td>22,6</td><td>26,2</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100953"></a>12</td><td>250</td><td>0,3</td><td>14,5</td><td>17</td><td>19,8</td><td>22,7</td><td>26,2</td><td>30,4</td><td>34,6</td><td>39,4</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100954"></a>13</td><td>320</td><td>0,3</td><td>17,6</td><td>20,7</td><td>24,2</td><td>27,7</td><td>32</td><td>37,2</td><td>42,4</td><td>48,4</td><td colspan="2">54,5</td><td>-</td></tr>
<tr><td><a id="p100955"></a>14</td><td>400</td><td>0,3</td><td>21,1</td><td>24,8</td><td>29,1</td><td>33,3</td><td>38,6</td><td>45</td><td>51,3</td><td>58,7</td><td colspan="2">66</td><td>76,5</td></tr>
<tr><td colspan="3"><a id="p100956"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>


<a id="p100957"></a>*Примечание.* Нормативное время рассчитано при шероховатости Ra 0,2, для шероховатости Ra 0,1 время следует умножать на коэффициент 1,25.


<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100958"></a>Неполное штучное время<br>Растачивание отверстий<br>Алюминиевые сплавы<br>49...118 НВ, Ra 0,2...0,16</td><td colspan="4">Резцы с пластинами<br>Натуральный алмаз</td></tr>
<tr><td colspan="4">Карта 21</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p100959"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100960"></a>1</td><td>10</td><td>0,1</td><td>1,04</td><td>1,25</td><td>1,52</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100961"></a>2</td><td>15</td><td>0,12</td><td>1,09</td><td>1,30</td><td>1,59</td><td>1,87</td><td>2,13</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100962"></a>3</td><td>20</td><td>0,15</td><td>1,16</td><td>1,37</td><td>1,67</td><td>1,94</td><td>2,23</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100963"></a>4</td><td>30</td><td>0,15</td><td>1,28</td><td>1,50</td><td>1,75</td><td>2,12</td><td>2,40</td><td>2,81</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100964"></a>5</td><td>50</td><td>0,2</td><td>1,33</td><td>1,56</td><td>1,81</td><td>2,18</td><td>2,47</td><td>2,88</td><td>3,20</td><td>3,71</td><td colspan="2">4,22</td><td>-</td></tr>
<tr><td><a id="p100965"></a>6</td><td>65</td><td>0,25</td><td>1,38</td><td>1,62</td><td>1,88</td><td>2,26</td><td>2,55</td><td>2,97</td><td>3,27</td><td>3,8</td><td colspan="2">4,3</td><td>-</td></tr>
<tr><td><a id="p100966"></a>7</td><td>80</td><td>0,25</td><td>1,48</td><td>1,75</td><td>1,95</td><td>2,51</td><td>2,85</td><td>3,34</td><td>3,37</td><td>3,90</td><td colspan="2">4,4</td><td>5,2</td></tr>
<tr><td><a id="p100967"></a>8</td><td>100</td><td>0,25</td><td>1,52</td><td>1,77</td><td>2,16</td><td>2,61</td><td>3,02</td><td>3,61</td><td>3,82</td><td>4,4</td><td colspan="2">5,0</td><td>5,9</td></tr>
<tr><td><a id="p100968"></a>9</td><td>125</td><td>0,3</td><td>1,66</td><td>1,96</td><td>2,41</td><td>2,81</td><td>3,20</td><td>3,76</td><td>4,3</td><td>5,0</td><td colspan="2">5,7</td><td>6,7</td></tr>
<tr><td><a id="p100969"></a>10</td><td>160</td><td>0,3</td><td>1,69</td><td>1,98</td><td>2,42</td><td>2,82</td><td>3,21</td><td>3,79</td><td>4,4</td><td>5,1</td><td colspan="2">5,8</td><td>6,8</td></tr>
<tr><td><a id="p100970"></a>11</td><td>200</td><td>0,3</td><td>1,88</td><td>2,22</td><td>2,72</td><td>3,19</td><td>3,66</td><td>4,3</td><td>5,0</td><td>5,8</td><td colspan="2">6,7</td><td>7,9</td></tr>
<tr><td><a id="p100971"></a>12</td><td>250</td><td>0,3</td><td>2,09</td><td>2,47</td><td>3,07</td><td>3,63</td><td>4,17</td><td>5,0</td><td>5,7</td><td>6,8</td><td colspan="2">7,8</td><td>9,2</td></tr>
<tr><td><a id="p100972"></a>13</td><td>320</td><td>0,3</td><td>2,36</td><td>2,81</td><td>3,53</td><td>4,2</td><td>4,9</td><td>5,8</td><td>6,8</td><td>8,0</td><td colspan="2">9,3</td><td>11,1</td></tr>
<tr><td><a id="p100973"></a>14</td><td>400</td><td>0,3</td><td>2,68</td><td>3,19</td><td>4,04</td><td>4,9</td><td>5,7</td><td>6,8</td><td>8,0</td><td>9,5</td><td colspan="2">11,0</td><td>13,2</td></tr>
<tr><td colspan="3"><a id="p100974"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100975"></a>Неполное штучное время<br>Растачивание отверстий<br>Алюминиевые сплавы<br>49...118 НВ, Ra 0,2...0,16</td><td colspan="4">Резцы с пластинами<br>Натуральный алмаз</td></tr>
<tr><td colspan="4">Карта 21</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p100976"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100977"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100978"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100979"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100980"></a>4</td><td>30</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100981"></a>5</td><td>50</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100982"></a>6</td><td>65</td><td>0,25</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100983"></a>7</td><td>80</td><td>0,25</td><td>5,79</td><td>6,83</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100984"></a>8</td><td>100</td><td>0,25</td><td>6,69</td><td>7,7</td><td>8,86</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100985"></a>9</td><td>125</td><td>0,3</td><td>7,74</td><td>8,56</td><td>10,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100986"></a>10</td><td>160</td><td>0,3</td><td>7,58</td><td>8,75</td><td>10,9</td><td>11,4</td><td>13</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100987"></a>11</td><td>200</td><td>0,3</td><td>8,94</td><td>10,4</td><td>12</td><td>13,6</td><td>15,6</td><td>17,9</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100988"></a>12</td><td>250</td><td>0,3</td><td>10,5</td><td>12,2</td><td>14,1</td><td>16,1</td><td>18,4</td><td>21,3</td><td>24,1</td><td>27,5</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100989"></a>13</td><td>320</td><td>0,3</td><td>12,6</td><td>14,7</td><td>17,1</td><td>19,5</td><td>22,4</td><td>26</td><td>29,5</td><td>33,6</td><td colspan="2">37,7</td><td>-</td></tr>
<tr><td><a id="p100990"></a>14</td><td>400</td><td>0,3</td><td>15</td><td>17,6</td><td>20,5</td><td>23,4</td><td>27</td><td>31,3</td><td>35,6</td><td>40,6</td><td colspan="2">45,6</td><td>52,8</td></tr>
<tr><td colspan="3"><a id="p100991"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>


<a id="p100992"></a>*Примечание.* Нормативное время рассчитано при шероховатости Ra 0,16, для шероховатости Ra 0,2 время следует умножать на коэффициент 0,75.


<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p100993"></a>Неполное штучное время<br>Растачивание отверстий<br>Алюминиевые сплавы<br>49...118 НВ, Ra 0,8...0,32, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Синтетический алмаз</td></tr>
<tr><td colspan="4">Карта 22</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p100994"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p100995"></a>1</td><td>10</td><td>0,1</td><td>1,03</td><td>1,32</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100996"></a>2</td><td>15</td><td>0,12</td><td>1,19</td><td>1,52</td><td>1,87</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100997"></a>3</td><td>20</td><td>0,15</td><td>1,27</td><td>1,66</td><td>1,96</td><td>2,29</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100998"></a>4</td><td>30</td><td>0,15</td><td>1,45</td><td>1,84</td><td>2,08</td><td>2,42</td><td>2,74</td><td>3,20</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p100999"></a>5</td><td>50</td><td>0,2</td><td>1,52</td><td>1,91</td><td>2,29</td><td>2,72</td><td>3,10</td><td>3,63</td><td>4,16</td><td>4,27</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101000"></a>6</td><td>65</td><td>0,25</td><td>1,53</td><td>1,97</td><td>2,33</td><td>2,82</td><td>3,14</td><td>3,73</td><td>4,43</td><td>4,85</td><td colspan="2">5,20</td><td>5,61</td></tr>
<tr><td><a id="p101001"></a>7</td><td>80</td><td>0,25</td><td>1,54</td><td>1,98</td><td>2,38</td><td>2,83</td><td>3,23</td><td>3,84</td><td>4,50</td><td>5,20</td><td colspan="2">5,52</td><td>6,49</td></tr>
<tr><td><a id="p101002"></a>8</td><td>100</td><td>0,25</td><td>1,69</td><td>2,11</td><td>2,60</td><td>3,06</td><td>3,50</td><td>4,14</td><td>4,76</td><td>5,79</td><td colspan="2">6,36</td><td>7,55</td></tr>
<tr><td><a id="p101003"></a>9</td><td>125</td><td>0,3</td><td>1,79</td><td>2,24</td><td>2,75</td><td>3,21</td><td>4,00</td><td>4,31</td><td>5,52</td><td>6,19</td><td colspan="2">6,60</td><td>7,78</td></tr>
<tr><td><a id="p101004"></a>10</td><td>160</td><td>0,3</td><td>1,87</td><td>2,38</td><td>2,95</td><td>3,49</td><td>4,10</td><td>4,77</td><td>5,63</td><td>6,74</td><td colspan="2">7,44</td><td>8,87</td></tr>
<tr><td><a id="p101005"></a>11</td><td>200</td><td>0,3</td><td>2,0</td><td>2,52</td><td>3,10</td><td>3,65</td><td>4,20</td><td>4,98</td><td>5,75</td><td>6,79</td><td colspan="2">8,05</td><td>9,17</td></tr>
<tr><td><a id="p101006"></a>12</td><td>250</td><td>0,3</td><td>2,22</td><td>2,82</td><td>3,52</td><td>4,18</td><td>4,83</td><td>5,75</td><td>6,68</td><td>7,88</td><td colspan="2">9,08</td><td>10,8</td></tr>
<tr><td><a id="p101007"></a>13</td><td>320</td><td>0,3</td><td>2,5</td><td>3,21</td><td>4,06</td><td>4,85</td><td>5,64</td><td>6,78</td><td>7,90</td><td>9,42</td><td colspan="2">10,9</td><td>13,0</td></tr>
<tr><td><a id="p101008"></a>14</td><td>400</td><td>0,3</td><td>2,83</td><td>3,66</td><td>4,66</td><td>5,62</td><td>6,81</td><td>7,85</td><td>9,30</td><td>11,1</td><td colspan="2">12,9</td><td>15,5</td></tr>
<tr><td colspan="3"><a id="p101009"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p101010"></a>Неполное штучное время<br>Растачивание отверстий<br>Алюминиевые сплавы<br>49...118 НВ, Ra 0,8...0,32, 7 квалитет</td><td colspan="4">Резцы с пластинами<br>Синтетический алмаз</td></tr>
<tr><td colspan="4">Карта 22</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p101011"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p101012"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101013"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101014"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101015"></a>4</td><td>30</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101016"></a>5</td><td>50</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101017"></a>6</td><td>65</td><td>0,25</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101018"></a>7</td><td>80</td><td>0,25</td><td>7,32</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101019"></a>8</td><td>100</td><td>0,25</td><td>8,53</td><td>9,88</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101020"></a>9</td><td>125</td><td>0,3</td><td>8,78</td><td>10,1</td><td>11,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101021"></a>10</td><td>160</td><td>0,3</td><td>10,1</td><td>11,7</td><td>13,6</td><td>14,2</td><td>15,2</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101022"></a>11</td><td>200</td><td>0,3</td><td>10,4</td><td>12,1</td><td>14,0</td><td>15,8</td><td>18,2</td><td>21,0</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101023"></a>12</td><td>250</td><td>0,3</td><td>12,3</td><td>14,3</td><td>16,6</td><td>18,9</td><td>21,8</td><td>25,2</td><td>28,5</td><td>32,5</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101024"></a>13</td><td>320</td><td>0,3</td><td>14,8</td><td>17,3</td><td>20,1</td><td>23,1</td><td>26,4</td><td>30,6</td><td>34,8</td><td>35,1</td><td colspan="2">45,7</td><td>-</td></tr>
<tr><td><a id="p101025"></a>14</td><td>400</td><td>0,3</td><td>17,7</td><td>20,7</td><td>24,2</td><td>27,6</td><td>31,9</td><td>37,0</td><td>42,1</td><td>48,1</td><td colspan="2">55,3</td><td>63,3</td></tr>
<tr><td colspan="3"><a id="p101026"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>


<a id="p101027"></a>*Примечание.* Нормативное время рассчитано при шероховатости Ra 0,32, для шероховатости Ra 0,8 время следует умножать на коэффициент 0,5.


<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p101028"></a>Неполное штучное время<br>Растачивание отверстий<br>Медь красная<br>39...49 НВ, Ra 0,2...0,125</td><td colspan="4">Резцы с пластинами<br>Натуральный алмаз</td></tr>
<tr><td colspan="4">Карта 23</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p101029"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p101030"></a>1</td><td>10</td><td>0,1</td><td>1,03</td><td>1,32</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101031"></a>2</td><td>15</td><td>0,12</td><td>1,09</td><td>1,38</td><td>1,67</td><td>1,96</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101032"></a>3</td><td>20</td><td>0,15</td><td>1,20</td><td>1,50</td><td>1,83</td><td>2,11</td><td>2,43</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101033"></a>4</td><td>30</td><td>0,15</td><td>1,27</td><td>1,56</td><td>1,90</td><td>2,21</td><td>2,52</td><td>2,96</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101034"></a>5</td><td>50</td><td>0,2</td><td>1,34</td><td>1,66</td><td>2,02</td><td>2,37</td><td>2,67</td><td>3,14</td><td>3,58</td><td>4,15</td><td colspan="2">4,72</td><td>-</td></tr>
<tr><td><a id="p101035"></a>6</td><td>65</td><td>0,25</td><td>1,46</td><td>1,83</td><td>2,22</td><td>2,60</td><td>2,96</td><td>3,48</td><td>3,97</td><td>4,63</td><td colspan="2">5,28</td><td>6,22</td></tr>
<tr><td><a id="p101036"></a>7</td><td>80</td><td>0,25</td><td>1,53</td><td>1,89</td><td>2,30</td><td>2,68</td><td>3,05</td><td>3,58</td><td>4,08</td><td>4,76</td><td colspan="2">5,41</td><td>6,36</td></tr>
<tr><td><a id="p101037"></a>8</td><td>100</td><td>0,25</td><td>1,67</td><td>2,08</td><td>2,56</td><td>3,01</td><td>3,44</td><td>4,06</td><td>4,68</td><td>5,46</td><td colspan="2">6,24</td><td>7,38</td></tr>
<tr><td><a id="p101038"></a>9</td><td>125</td><td>0,3</td><td>1,78</td><td>2,24</td><td>2,76</td><td>3,25</td><td>3,72</td><td>4,40</td><td>5,07</td><td>5,94</td><td colspan="2">6,80</td><td>8,05</td></tr>
<tr><td><a id="p101039"></a>10</td><td>160</td><td>0,3</td><td>1,89</td><td>2,39</td><td>2,95</td><td>3,47</td><td>3,98</td><td>4,72</td><td>5,48</td><td>6,39</td><td colspan="2">7,33</td><td>8,68</td></tr>
<tr><td><a id="p101040"></a>11</td><td>200</td><td>0,3</td><td>2,04</td><td>2,59</td><td>3,20</td><td>3,77</td><td>4,35</td><td>5,17</td><td>5,97</td><td>7,03</td><td colspan="2">8,07</td><td>9,59</td></tr>
<tr><td><a id="p101041"></a>12</td><td>250</td><td>0,3</td><td>2,27</td><td>2,88</td><td>3,61</td><td>4,73</td><td>4,96</td><td>5,94</td><td>6,90</td><td>8,15</td><td colspan="2">9,39</td><td>11,2</td></tr>
<tr><td><a id="p101042"></a>13</td><td>320</td><td>0,3</td><td>2,64</td><td>3,39</td><td>4,28</td><td>5,13</td><td>5,89</td><td>7,10</td><td>8,27</td><td>9,87</td><td colspan="2">11,4</td><td>13,7</td></tr>
<tr><td><a id="p101043"></a>14</td><td>400</td><td>0,3</td><td>2,92</td><td>3,81</td><td>4,85</td><td>5,86</td><td>6,86</td><td>8,33</td><td>9,75</td><td>11,7</td><td colspan="2">13,5</td><td>16,3</td></tr>
<tr><td colspan="3"><a id="p101044"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p101045"></a>Неполное штучное время<br>Растачивание отверстий<br>Медь красная<br>39...49 НВ, Ra 0,2...0,125</td><td colspan="4">Резцы с пластинами<br>Натуральный алмаз</td></tr>
<tr><td colspan="4">Карта 23</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p101046"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p101047"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101048"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101049"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101050"></a>4</td><td>30</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101051"></a>5</td><td>50</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101052"></a>6</td><td>65</td><td>0,25</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101053"></a>7</td><td>80</td><td>0,25</td><td>8,26</td><td>9,50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101054"></a>8</td><td>100</td><td>0,25</td><td>8,34</td><td>9,66</td><td>11,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101055"></a>9</td><td>125</td><td>0,3</td><td>9,12</td><td>10,6</td><td>12,2</td><td>13,9</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101056"></a>10</td><td>160</td><td>0,3</td><td>9,83</td><td>11,4</td><td>13,2</td><td>15,0</td><td>17,2</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101057"></a>11</td><td>200</td><td>0,3</td><td>10,9</td><td>12,6</td><td>14,6</td><td>16,6</td><td>19,1</td><td>22,1</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101058"></a>12</td><td>250</td><td>0,3</td><td>12,8</td><td>14,9</td><td>17,3</td><td>19,7</td><td>22,6</td><td>26,2</td><td>29,7</td><td>33,7</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101059"></a>13</td><td>320</td><td>0,3</td><td>15,6</td><td>18,2</td><td>21,3</td><td>24,2</td><td>27,9</td><td>32,4</td><td>36,9</td><td>42,1</td><td colspan="2">48,4</td><td>-</td></tr>
<tr><td><a id="p101060"></a>14</td><td>400</td><td>0,3</td><td>18,7</td><td>21,9</td><td>25,5</td><td>29,2</td><td>33,7</td><td>39,2</td><td>44,6</td><td>51,0</td><td colspan="2">58,6</td><td>67,2</td></tr>
<tr><td colspan="3"><a id="p101061"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>


<a id="p101062"></a>*Примечание.* Нормативное время рассчитано при шероховатости Ra 0,2, для шероховатости Ra 0,125 время следует умножать на коэффициент 1,2.


<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p101063"></a>Неполное штучное время<br>Растачивание отверстий<br>Металлокерамика<br>Ra 1,25</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="4">Карта 24</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p101064"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td colspan="2">120</td><td>150</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p101065"></a>1</td><td>10</td><td>0,1</td><td>0,75</td><td>0,88</td><td>1,01</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101066"></a>2</td><td>15</td><td>0,12</td><td>0,80</td><td>0,93</td><td>1,08</td><td>1,21</td><td>1,32</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101067"></a>3</td><td>20</td><td>0,15</td><td>0,88</td><td>1,02</td><td>1,18</td><td>1,32</td><td>1,47</td><td>1,65</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101068"></a>4</td><td>30</td><td>0,2</td><td>1,04</td><td>1,20</td><td>1,42</td><td>1,62</td><td>1,80</td><td>2,07</td><td>2,32</td><td>2,64</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101069"></a>5</td><td>50</td><td>0,2</td><td>1,14</td><td>1,32</td><td>1,57</td><td>1,80</td><td>2,01</td><td>2,31</td><td>2,59</td><td>2,96</td><td colspan="2">3,33</td><td>3,8</td></tr>
<tr><td><a id="p101070"></a>6</td><td>65</td><td>0,2</td><td>1,24</td><td>1,45</td><td>1,72</td><td>1,98</td><td>2,22</td><td>2,56</td><td>2,88</td><td>3,3</td><td colspan="2">3,7</td><td>4,3</td></tr>
<tr><td><a id="p101071"></a>7</td><td>80</td><td>0,2</td><td>1,32</td><td>1,53</td><td>1,83</td><td>2,11</td><td>2,37</td><td>2,73</td><td>3,09</td><td>3,55</td><td colspan="2">4,0</td><td>4,6</td></tr>
<tr><td><a id="p101072"></a>8</td><td>100</td><td>0,2</td><td>1,45</td><td>1,69</td><td>2,04</td><td>2,37</td><td>2,67</td><td>3,12</td><td>3,55</td><td>4,1</td><td colspan="2">4,6</td><td>5,4</td></tr>
<tr><td><a id="p101073"></a>9</td><td>125</td><td>0,25</td><td>1,72</td><td>2,03</td><td>2,50</td><td>2,94</td><td>3,36</td><td>3,98</td><td>4,6</td><td>5,4</td><td colspan="2">6,1</td><td>7,3</td></tr>
<tr><td><a id="p101074"></a>10</td><td>160</td><td>0,25</td><td>1,97</td><td>2,33</td><td>2,91</td><td>3,45</td><td>3,97</td><td>4,75</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td>8,9</td></tr>
<tr><td><a id="p101075"></a>11</td><td>200</td><td>0,25</td><td>2,03</td><td>2,41</td><td>2,99</td><td>3,54</td><td>4,08</td><td>4,9</td><td>5,6</td><td>6,6</td><td colspan="2">7,6</td><td>9,1</td></tr>
<tr><td><a id="p101076"></a>12</td><td>250</td><td>0,25</td><td>2,2</td><td>2,47</td><td>3,2</td><td>3,8</td><td>4,3</td><td>5,7</td><td>6,3</td><td>7,4</td><td colspan="2">8,5</td><td>10,2</td></tr>
<tr><td><a id="p101077"></a>13</td><td>320</td><td>0,25</td><td>2,44</td><td>2,86</td><td>3,60</td><td>4,3</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,3</td><td colspan="2">9,5</td><td>11,4</td></tr>
<tr><td><a id="p101078"></a>14</td><td>400</td><td>0,35</td><td>2,73</td><td>3,26</td><td>4,14</td><td>5,0</td><td>5,8</td><td>7,0</td><td>8,2</td><td>9,8</td><td colspan="2">11,3</td><td>13,6</td></tr>
<tr><td colspan="3"><a id="p101079"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="6%"><col width="8%"><col width="3%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="10" rowspan="3"><a id="p101080"></a>Неполное штучное время<br>Растачивание отверстий<br>Металлокерамика<br>Ra 1,25</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="4">Карта 24</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 2</td></tr>
<tr><td rowspan="3"><a id="p101081"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="11">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td colspan="2">600</td><td>700</td></tr>
<tr><td colspan="11">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p101082"></a>1</td><td>10</td><td>0,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101083"></a>2</td><td>15</td><td>0,12</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101084"></a>3</td><td>20</td><td>0,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101085"></a>4</td><td>30</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101086"></a>5</td><td>50</td><td>0,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101087"></a>6</td><td>65</td><td>0,2</td><td>4,84</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101088"></a>7</td><td>80</td><td>0,2</td><td>5,19</td><td>5,93</td><td>6,77</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101089"></a>8</td><td>100</td><td>0,2</td><td>6,1</td><td>7</td><td>8,03</td><td>9,04</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101090"></a>9</td><td>125</td><td>0,25</td><td>8,24</td><td>9,55</td><td>11</td><td>12,5</td><td>14,3</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101091"></a>10</td><td>160</td><td>0,25</td><td>10,1</td><td>11,8</td><td>13,6</td><td>15,5</td><td>17,9</td><td>20,6</td><td>23,4</td><td>-</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101092"></a>11</td><td>200</td><td>0,25</td><td>10,3</td><td>12</td><td>13,9</td><td>15,8</td><td>18,2</td><td>21</td><td>23,9</td><td>27,1</td><td colspan="2">-</td><td>-</td></tr>
<tr><td><a id="p101093"></a>12</td><td>250</td><td>0,25</td><td>12,1</td><td>14,6</td><td>16,2</td><td>18,9</td><td>21,8</td><td>25,3</td><td>28,7</td><td>32,7</td><td colspan="2">33,1</td><td>-</td></tr>
<tr><td><a id="p101094"></a>13</td><td>320</td><td>0,25</td><td>13</td><td>15,2</td><td>17,7</td><td>20,1</td><td>23,2</td><td>26,8</td><td>30,5</td><td>34,7</td><td colspan="2">39</td><td>45</td></tr>
<tr><td><a id="p101095"></a>14</td><td>400</td><td>0,35</td><td>15,5</td><td>18,2</td><td>21,2</td><td>24,2</td><td>27,9</td><td>32,4</td><td>36,9</td><td>42,1</td><td colspan="2">47,3</td><td>54,7</td></tr>
<tr><td colspan="3"><a id="p101096"></a>Индекс</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td colspan="2">у</td><td>ф</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="13" rowspan="2"><a id="p101097"></a>Неполное штучное время<br>Растачивание отверстий Ra 0,4...0,32, 7 квалитет<br>Твердый сплав HRCэ 80...90</td><td colspan="6">Резцы с пластинами<br>Композит 10 (Гексанит-Р)</td></tr>
<tr><td colspan="6">Карта 25</td></tr>
<tr><td rowspan="3"><a id="p101098"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="16">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>12</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td>120</td><td>150</td><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td></tr>
<tr><td colspan="16">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p101099"></a>1</td><td>10</td><td>0,1</td><td>2,28</td><td>3,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101100"></a>2</td><td>15</td><td>0,12</td><td>2,48</td><td>3,54</td><td>3,61</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101101"></a>3</td><td>20</td><td>0,15</td><td>2,70</td><td>3,71</td><td>3,93</td><td>6,09</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101102"></a>4</td><td>30</td><td>0,2</td><td>3,61</td><td>5,02</td><td>6,73</td><td>8,43</td><td>10,1</td><td>12,6</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101103"></a>5</td><td>50</td><td>0,3</td><td>3,76</td><td>5,21</td><td>7,00</td><td>8,75</td><td>10,5</td><td>13,1</td><td>14,2</td><td>19,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101104"></a>6</td><td>65</td><td>0,3</td><td>4,54</td><td>6,35</td><td>8,56</td><td>10,7</td><td>12,9</td><td>16,1</td><td>19,4</td><td>23,6</td><td>27,9</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101105"></a>7</td><td>80</td><td>0,3</td><td>4,60</td><td>6,40</td><td>8,62</td><td>10,9</td><td>13,0</td><td>16,3</td><td>19,6</td><td>24,6</td><td>28,8</td><td>34,4</td><td>39,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101106"></a>8</td><td>100</td><td>0,4</td><td>4,68</td><td>6,50</td><td>8,75</td><td>11,1</td><td>13,2</td><td>16,5</td><td>19,8</td><td>24,8</td><td>28,9</td><td>34,8</td><td>40,1</td><td>47,6</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101107"></a>9</td><td>125</td><td>0,4</td><td>4,72</td><td>6,57</td><td>8,81</td><td>11,5</td><td>13,4</td><td>16,7</td><td>20,0</td><td>24,9</td><td>29,0</td><td>35,0</td><td>40,3</td><td>48,0</td><td>56,3</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101108"></a>10</td><td>160</td><td>0,4</td><td>4,84</td><td>6,72</td><td>9,02</td><td>11,8</td><td>13,7</td><td>16,9</td><td>20,5</td><td>25,1</td><td>29,3</td><td>36,3</td><td>41,8</td><td>49,6</td><td>57,4</td><td>64,3</td><td>74,9</td><td>-</td></tr>
<tr><td><a id="p101109"></a>11</td><td>200</td><td>0,5</td><td>4,90</td><td>6,79</td><td>9,09</td><td>12,3</td><td>14,0</td><td>17,3</td><td>21,0</td><td>26,1</td><td>30,8</td><td>37,8</td><td>43,5</td><td>51,6</td><td>60,8</td><td>70,3</td><td>81,8</td><td>87,6</td></tr>
<tr><td colspan="3"><a id="p101110"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td></tr>
</table>


<a id="p101111"></a>Поправочные коэффициенты на неполное штучное время
для измененных условий работы:


<table>
<colgroup><col width="50%"><col width="50%"></colgroup>
<tr><td colspan="2"><a id="p101112"></a>Шероховатость обрабатываемой поверхности, Ra</td></tr>
<tr><td><a id="p101113"></a>0,32</td><td>0,40</td></tr>
<tr><td colspan="2"><a id="p101114"></a>Значение коэффициента Ку</td></tr>
<tr><td><a id="p101115"></a>1,5</td><td>1,0</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="11%"><col width="10%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="12" rowspan="2"><a id="p101116"></a>Неполное штучное время<br>Растачивание отверстий Ra 1,25, 7 квалитет<br>Твердый сплав HRCэ 80...90</td><td colspan="4">Резцы с пластинами<br>Композит 01 (Эльбор-Р)</td></tr>
<tr><td colspan="4">Карта 26</td></tr>
<tr><td rowspan="3"><a id="p101117"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="13">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td>120</td><td>150</td><td>175</td><td>210</td><td>250</td></tr>
<tr><td colspan="13">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p101118"></a>1</td><td>10</td><td>0,1</td><td>1,69</td><td>2,30</td><td>2,96</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101119"></a>2</td><td>15</td><td>0,12</td><td>2,28</td><td>3,11</td><td>4,11</td><td>5,09</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101120"></a>3</td><td>20</td><td>0,15</td><td>3,19</td><td>4,43</td><td>5,93</td><td>7,39</td><td>8,88</td><td>11,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101121"></a>4</td><td>30</td><td>0,2</td><td>3,45</td><td>4,79</td><td>6,41</td><td>7,94</td><td>9,61</td><td>12,0</td><td>14,3</td><td>17,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101122"></a>5</td><td>50</td><td>0,2</td><td>4,04</td><td>4,85</td><td>7,57</td><td>9,49</td><td>11,4</td><td>14,2</td><td>17,1</td><td>20,8</td><td>24,5</td><td>30,1</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101123"></a>6</td><td>65</td><td>0,2</td><td>4,72</td><td>6,61</td><td>8,92</td><td>11,2</td><td>13,5</td><td>16,9</td><td>21,8</td><td>24,7</td><td>29,2</td><td>35,9</td><td>41,5</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101124"></a>7</td><td>80</td><td>0,2</td><td>4,77</td><td>6,67</td><td>9,31</td><td>11,7</td><td>14,1</td><td>17,6</td><td>22,4</td><td>27,4</td><td>32,4</td><td>39,8</td><td>45,0</td><td>54,6</td><td>58,3</td></tr>
<tr><td colspan="3"><a id="p101125"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="10%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="13" rowspan="3"><a id="p101126"></a>Неполное штучное время<br>Растачивание отверстий Ra 0,63, 7 квалитет<br>Твердый сплав HRCэ 80...90</td><td colspan="6">Резцы с пластинами<br>Синтетический алмаз</td></tr>
<tr><td colspan="6">Карта 27</td></tr>
<tr><td colspan="4">Лист 1</td><td colspan="2">Листов 1</td></tr>
<tr><td rowspan="3"><a id="p101127"></a>N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия d, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="16">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>12</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td>120</td><td>150</td><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td></tr>
<tr><td colspan="16">Время на рабочий ход tнш, мин.</td></tr>
<tr><td><a id="p101128"></a>1</td><td>10</td><td>0,1</td><td>2,78</td><td>3,89</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101129"></a>2</td><td>15</td><td>0,12</td><td>2,84</td><td>3,95</td><td>5,28</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101130"></a>3</td><td>20</td><td>0,15</td><td>3,26</td><td>4,51</td><td>6,06</td><td>7,48</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101131"></a>4</td><td>30</td><td>0,15</td><td>3,32</td><td>4,59</td><td>6,14</td><td>9,3</td><td>9,8</td><td>11,4</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101132"></a>5</td><td>50</td><td>0,2</td><td>4,04</td><td>5,63</td><td>7,57</td><td>9,49</td><td>11,4</td><td>14,2</td><td>17,1</td><td>20,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101133"></a>6</td><td>65</td><td>0,25</td><td>4,09</td><td>5,70</td><td>7,63</td><td>9,56</td><td>11,5</td><td>14,3</td><td>17,9</td><td>20,9</td><td>24,6</td><td>30,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101134"></a>7</td><td>80</td><td>0,25</td><td>4,26</td><td>5,91</td><td>7,92</td><td>9,92</td><td>11,9</td><td>14,8</td><td>17,8</td><td>21,6</td><td>25,5</td><td>31,3</td><td>36,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101135"></a>8</td><td>100</td><td>0,25</td><td>4,42</td><td>6,12</td><td>8,22</td><td>10,3</td><td>12,3</td><td>15,4</td><td>18,4</td><td>22,4</td><td>26,4</td><td>32,4</td><td>37,4</td><td>44,4</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101136"></a>9</td><td>125</td><td>0,3</td><td>4,65</td><td>6,36</td><td>8,67</td><td>10,9</td><td>13,0</td><td>16,2</td><td>19,4</td><td>23,7</td><td>27,9</td><td>34,2</td><td>39,4</td><td>46,7</td><td>55,3</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101137"></a>10</td><td>160</td><td>0,3</td><td>4,84</td><td>6,72</td><td>9,02</td><td>11,3</td><td>13,5</td><td>16,9</td><td>20,2</td><td>25,1</td><td>29,6</td><td>36,3</td><td>41,8</td><td>49,6</td><td>58,5</td><td>67,4</td><td>78,5</td><td>-</td></tr>
<tr><td colspan="3"><a id="p101138"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td></tr>
</table>







<table>
<colgroup><col width="25%"><col width="19%"><col width="19%"><col width="19%"><col width="19%"></colgroup>
<tr><td colspan="3" rowspan="2"><a id="p101139"></a>Рекомендуемые режимы резания</td><td colspan="2">Приложение 1</td></tr>
<tr><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="2"><a id="p101140"></a>Обрабатываемый материал</td><td rowspan="2">Твердость, НВ</td><td rowspan="2">Шероховатость поверхности, Ra, мкм</td><td colspan="2">Режимы резания</td></tr>
<tr><td>V, м/мин.</td><td>Sо, мм/об.</td></tr>
<tr><td colspan="5"><a id="p101141"></a>Обработка резцами из твердого сплава</td></tr>
<tr><td rowspan="6"><a id="p101142"></a>Чугуны серые, ковкие и высокопрочные</td><td rowspan="2">&lt; 167</td><td>1</td><td rowspan="2">95...180</td><td>0,03...0,06</td></tr>
<tr><td>1,6</td><td>0,04...0,06</td></tr>
<tr><td rowspan="2"><a id="p101143"></a>167...224</td><td>1</td><td rowspan="2">85...160</td><td>0,02...0,06</td></tr>
<tr><td>1,6</td><td>0,03...0,06</td></tr>
<tr><td rowspan="2"><a id="p101144"></a>225...264</td><td>1</td><td rowspan="2">75...135</td><td>0,02...0,06</td></tr>
<tr><td>1,6</td><td>0,03...0,06</td></tr>
<tr><td rowspan="2"><a id="p101145"></a>Чугуны термообработанные и отбеленные</td><td rowspan="2">HRCэ 41...47</td><td>1</td><td rowspan="2">80...120</td><td>0,02...0,06</td></tr>
<tr><td>1,6</td><td>0,03...0,08</td></tr>
<tr><td rowspan="3"><a id="p101146"></a>Стали низкоуглеродистые качественные</td><td rowspan="3">144...213</td><td>0,63</td><td rowspan="3">125...290</td><td>0,02...0,07</td></tr>
<tr><td>0,8</td><td>0,03...0,09</td></tr>
<tr><td>1,6</td><td>0,04...0,13</td></tr>
<tr><td rowspan="3"><a id="p101147"></a>Стали среднеуглеродистые качественные</td><td rowspan="3">150...213</td><td>0,63</td><td rowspan="3">130...200</td><td>0,02...0,07</td></tr>
<tr><td>0,8</td><td>0,03...0,09</td></tr>
<tr><td>1,6</td><td>0,04...0,13</td></tr>
<tr><td rowspan="6"><a id="p101148"></a>Стали легированные конструкционные</td><td rowspan="3">150...217</td><td>0,63</td><td rowspan="3">90...188</td><td>0,015...0,04</td></tr>
<tr><td>0,8</td><td>0,02...0,05</td></tr>
<tr><td><a id="p101149"></a>1,6</td><td>0,03...0,07</td></tr>
<tr><td rowspan="3">218...279</td><td>0,63</td><td rowspan="3">85...165</td><td>0,015...0,04</td></tr>
<tr><td>0,8</td><td>0,02...0,05</td></tr>
<tr><td>1,6</td><td>0,025...0,07</td></tr>
<tr><td rowspan="5"><a id="p101150"></a>Стали высоколегированные и труднообрабатываемые</td><td rowspan="2">151...224</td><td>1</td><td rowspan="2">75...126</td><td>0,02...0,06</td></tr>
<tr><td>1,6</td><td>0,025...0,08</td></tr>
<tr><td rowspan="3"><a id="p101151"></a>225...280</td><td>0,63</td><td rowspan="3">65...113</td><td>0,02...0,05</td></tr>
<tr><td>0,8</td><td>0,02...0,06</td></tr>
<tr><td>1,6</td><td>0,025..0,08</td></tr>
<tr><td rowspan="4"><a id="p101152"></a>Стали термообработанные</td><td rowspan="2">HRCэ 30...35</td><td>0,8</td><td rowspan="2">60...100</td><td>0,02...0,06</td></tr>
<tr><td>1,6</td><td>0,03...0,08</td></tr>
<tr><td rowspan="2"><a id="p101153"></a>HRCэ 36...65</td><td>0,5</td><td rowspan="2">40...80</td><td>0,02...0,05</td></tr>
<tr><td>1,6</td><td>0,03...0,06</td></tr>
<tr><td rowspan="6"><a id="p101154"></a>Алюминиевые сплавы</td><td rowspan="3">&lt; 74</td><td>0,32</td><td rowspan="3">125...500</td><td>0,02...0,05</td></tr>
<tr><td>0,8</td><td>0,03...0,09</td></tr>
<tr><td>1,6</td><td>0,03...0,12</td></tr>
<tr><td rowspan="3"><a id="p101155"></a>74...110</td><td>0,32</td><td rowspan="3">125...343</td><td>0,02...0,05</td></tr>
<tr><td>0,8</td><td>0,03...0,09</td></tr>
<tr><td>1,6</td><td>0,03...0,12</td></tr>
<tr><td rowspan="7"><a id="p101156"></a>Бронзы, латуни</td><td rowspan="4">&lt; 119</td><td>0,32</td><td rowspan="4">125...300</td><td>0,02...0,05</td></tr>
<tr><td>0,4</td><td>0,02...0,07</td></tr>
<tr><td>0,8</td><td>0,03...0,09</td></tr>
<tr><td><a id="p101157"></a>1,6</td><td>0,05...0,12</td></tr>
<tr><td rowspan="3">&gt;= 119</td><td>0,4</td><td rowspan="3">125...230</td><td>0,02...0,07</td></tr>
<tr><td>0,8</td><td>0,03...0,09</td></tr>
<tr><td>1,6</td><td>0,04...0,12</td></tr>
</table>



<table>
<colgroup><col width="25%"><col width="19%"><col width="19%"><col width="19%"><col width="19%"></colgroup>
<tr><td colspan="3" rowspan="2"><a id="p101158"></a>Рекомендуемые режимы резания</td><td colspan="2">Приложение 1</td></tr>
<tr><td colspan="2">Лист 2</td></tr>
<tr><td rowspan="2"><a id="p101159"></a>Обрабатываемый материал</td><td rowspan="2">Твердость, НВ</td><td rowspan="2">Шероховатость поверхности, Ra, мкм</td><td colspan="2">Режимы резания</td></tr>
<tr><td>V, м/мин.</td><td>Sо, мм/об.</td></tr>
<tr><td colspan="5"><a id="p101160"></a>Обработка резцами из композита 01 (Эльбор-Р)</td></tr>
<tr><td rowspan="6"><a id="p101161"></a>Чугуны серые, ковкие и высокопрочные</td><td rowspan="3">167...224</td><td>0,63</td><td rowspan="3">125...690</td><td>0,02...0,07</td></tr>
<tr><td>0,8</td><td>0,02...0,07</td></tr>
<tr><td>1,6</td><td>0,03...0,07</td></tr>
<tr><td rowspan="3"><a id="p101162"></a>224...264</td><td>0,63</td><td rowspan="3">125...470</td><td>0,02...0,05</td></tr>
<tr><td>0,8</td><td>0,03...0,07</td></tr>
<tr><td>1,6</td><td>0,02...0,07</td></tr>
<tr><td rowspan="3"><a id="p101163"></a>Чугуны термообработанные и отбеленные</td><td rowspan="3">HRCэ 41...47</td><td>0,63</td><td rowspan="3">106...183</td><td>0,02...0,04</td></tr>
<tr><td>0,8</td><td>0,02...0,06</td></tr>
<tr><td>1,6</td><td>0,03...0,07</td></tr>
<tr><td rowspan="3"><a id="p101164"></a>Стали низкоуглеродистые качественные</td><td rowspan="3">144...213</td><td>0,5</td><td rowspan="3">188...710</td><td>0,02...0,04</td></tr>
<tr><td>0,8</td><td>0,03...0,06</td></tr>
<tr><td>1,6</td><td>0,04...0,07</td></tr>
<tr><td rowspan="3"><a id="p101165"></a>Стали среднеуглеродистые качественные</td><td rowspan="3">214...279</td><td>0,5</td><td rowspan="3">126...603</td><td>0,02...0,04</td></tr>
<tr><td>0,8</td><td>0,02...0,06</td></tr>
<tr><td>1,6</td><td>0,03...0,07</td></tr>
<tr><td rowspan="3"><a id="p101166"></a>Стали легированные конструкционные</td><td rowspan="3">213...279</td><td>0,5</td><td rowspan="3">126...358</td><td>0,02...0,04</td></tr>
<tr><td>0,8</td><td>0,02...0,06</td></tr>
<tr><td>1,6</td><td>0,03...0,07</td></tr>
<tr><td rowspan="6"><a id="p101167"></a>Стали термообработанные</td><td rowspan="2">HRCэ 30...35</td><td>0,63</td><td rowspan="2">125...251</td><td>0,006...0,04</td></tr>
<tr><td>0,8</td><td>0,01...0,06</td></tr>
<tr><td rowspan="2"><a id="p101168"></a>HRCэ 36...55</td><td>0,63</td><td rowspan="2">100...138</td><td>0,006...0,04</td></tr>
<tr><td>0,8</td><td>0,01...0,06</td></tr>
<tr><td rowspan="2"><a id="p101169"></a>HRCэ 56...65</td><td>0,63</td><td rowspan="2">77...125</td><td>0,006...0,05</td></tr>
<tr><td>0,8</td><td>0,01...0,07</td></tr>
<tr><td rowspan="4"><a id="p101170"></a>Бронзы, латуни</td><td rowspan="2">&lt; 137</td><td>0,32</td><td rowspan="2">125...986</td><td>0,01...0,05</td></tr>
<tr><td>0,8</td><td>0,02...0,07</td></tr>
<tr><td rowspan="2"><a id="p101171"></a>&gt;= 137</td><td>0,32</td><td rowspan="2">125...716</td><td>0,01...0,05</td></tr>
<tr><td>0,8</td><td>0,02...0,07</td></tr>
<tr><td><a id="p101172"></a>Металлокерамика</td><td>-</td><td>1,25</td><td>125...276</td><td>0,03...0,07</td></tr>
<tr><td><a id="p101173"></a>Твердый сплав</td><td>HRCэ 80...90</td><td>1,25</td><td>15...21</td><td>0,03...0,06</td></tr>
<tr><td colspan="5"><a id="p101174"></a>Обработка резцами из композита 10 (Гексанит-Р)</td></tr>
<tr><td rowspan="2"><a id="p101175"></a>Чугуны серые, ковкие и высокопрочные</td><td rowspan="2">167...264</td><td>0,63</td><td rowspan="2">125...375</td><td>0,02...0,04</td></tr>
<tr><td>0,8</td><td>0,03...0,05</td></tr>
<tr><td rowspan="2"><a id="p101176"></a>Чугуны термообработанные и отбеленные</td><td rowspan="2">HRCэ 41...47</td><td>0,63</td><td rowspan="2">125...250</td><td>0,02...0,04</td></tr>
<tr><td>0,8</td><td>0,03...0,05</td></tr>
<tr><td rowspan="4"><a id="p101177"></a>Стали термообработанные</td><td rowspan="2">HRCэ 41...47</td><td>0,63</td><td rowspan="2">89...126</td><td>0,01...0,04</td></tr>
<tr><td>0,8</td><td>0,02...0,06</td></tr>
<tr><td rowspan="2"><a id="p101178"></a>HRCэ 48...65</td><td>0,63</td><td rowspan="2">70...100</td><td>0,02...0,04</td></tr>
<tr><td>0,8</td><td>0,03...0,06</td></tr>
</table>



<table>
<colgroup><col width="25%"><col width="19%"><col width="19%"><col width="19%"><col width="19%"></colgroup>
<tr><td colspan="3" rowspan="2"><a id="p101179"></a>Рекомендуемые режимы резания</td><td colspan="2">Приложение 1</td></tr>
<tr><td colspan="2">Лист 3</td></tr>
<tr><td rowspan="2"><a id="p101180"></a>Обрабатываемый материал</td><td rowspan="2">Твердость, НВ</td><td rowspan="2">Шероховатость поверхности, Ra, мкм</td><td colspan="2">Режимы резания</td></tr>
<tr><td>V, м/мин.</td><td>Sо, мм/об.</td></tr>
<tr><td rowspan="2"><a id="p101181"></a>Твердый сплав</td><td rowspan="2">HRCэ 80...90</td><td>0,32</td><td rowspan="2">29...56</td><td>0,01...0,05</td></tr>
<tr><td>0,4</td><td>0,02...0,06</td></tr>
<tr><td colspan="5"><a id="p101182"></a>Обработка резцами из исмита</td></tr>
<tr><td rowspan="2"><a id="p101183"></a>Чугуны серые, ковкие и высокопрочные</td><td rowspan="2">&lt; 224</td><td>0,63</td><td rowspan="2">125...420</td><td>0,01...0,04</td></tr>
<tr><td>0,8</td><td>0,02...0,05</td></tr>
<tr><td rowspan="2"><a id="p101184"></a>Чугуны термообработанные и отбеленные</td><td rowspan="2">HRCэ 41...47</td><td>0,63</td><td rowspan="2">125...420</td><td>0,01...0,04</td></tr>
<tr><td>0,8</td><td>0,02...0,05</td></tr>
<tr><td rowspan="4"><a id="p101185"></a>Стали термообработанные</td><td rowspan="2">HRCэ 35...50</td><td>0,63</td><td rowspan="2">116...157</td><td>0,01...0,04</td></tr>
<tr><td>1,6</td><td>0,025...0,05</td></tr>
<tr><td rowspan="2"><a id="p101186"></a>HRCэ 51...65</td><td>0,32</td><td rowspan="2">68...125</td><td>0,01...0,05</td></tr>
<tr><td>0,8</td><td>0,02...0,06</td></tr>
<tr><td colspan="5"><a id="p101187"></a>Обработка резцами из синтетических алмазов</td></tr>
<tr><td rowspan="2"><a id="p101188"></a>Алюминиевые сплавы</td><td rowspan="2">49...118</td><td>0,32</td><td rowspan="2">125...550</td><td>0,005...0,03</td></tr>
<tr><td>0,8</td><td>0,008...0,07</td></tr>
<tr><td rowspan="2"><a id="p101189"></a>Бронзы, латуни</td><td rowspan="2">39...49</td><td>0,32</td><td rowspan="2">125...389</td><td>0,005...0,03</td></tr>
<tr><td>0,80</td><td>0,008...0,07</td></tr>
<tr><td><a id="p101190"></a>Твердый сплав</td><td>HRCэ 80...90</td><td>0,63</td><td>22...43</td><td>0,01...0,06</td></tr>
<tr><td colspan="5"><a id="p101191"></a>Обработка резцами из натуральных алмазов</td></tr>
<tr><td rowspan="2"><a id="p101192"></a>Алюминиевые сплавы</td><td rowspan="2">49...118</td><td>0,16</td><td rowspan="2">125...550</td><td>0,01...0,03</td></tr>
<tr><td>0,2</td><td>0,01...0,04</td></tr>
<tr><td rowspan="2"><a id="p101193"></a>Бронзы</td><td rowspan="2">54...157</td><td>0,1</td><td rowspan="2">125...500</td><td>0,01...0,03</td></tr>
<tr><td>0,2</td><td>0,01...0,04</td></tr>
<tr><td rowspan="2"><a id="p101194"></a>Латуни</td><td rowspan="2">52...137</td><td>0,1</td><td rowspan="2">125...390</td><td>0,01...0,03</td></tr>
<tr><td>0,2</td><td>0,01...0,04</td></tr>
<tr><td rowspan="2"><a id="p101195"></a>Медь красная</td><td rowspan="2">39...49</td><td>0,125</td><td rowspan="2">125...440</td><td>0,01...0,03</td></tr>
<tr><td>0,2</td><td>0,01...0,04</td></tr>
<tr><td><a id="p101196"></a>Пластмассы</td><td>-</td><td>0,63</td><td>500...800</td><td>0,03...0,05</td></tr>
</table>







<table>
<colgroup><col width="10%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="16"><a id="p101197"></a>Вспомогательное время, связанное с переходом<br>Растачивание отверстий</td><td colspan="5">Приложение 2</td></tr>
<tr><td rowspan="3"><a id="p101198"></a>Диаметр обрабатываемого отверстия d, мм, до</td><td colspan="20">Длина обрабатываемой поверхности L, мм, до</td></tr>
<tr><td>15</td><td>20</td><td>30</td><td>40</td><td>50</td><td>65</td><td>80</td><td>100</td><td>120</td><td>150</td><td>175</td><td>210</td><td>250</td><td>290</td><td>340</td><td>400</td><td>460</td><td>530</td><td>600</td><td>700</td></tr>
<tr><td colspan="20">Время на переход tпер, мин.</td></tr>
<tr><td><a id="p101199"></a>6</td><td>0,57</td><td>0,65</td><td>0,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101200"></a>8</td><td>0,6</td><td>0,7</td><td>0,75</td><td>0,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101201"></a>12</td><td>0,65</td><td>0,75</td><td>0,82</td><td>0,88</td><td>0,92</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101202"></a>20</td><td>0,72</td><td>0,82</td><td>0,9</td><td>0,95</td><td>1,02</td><td>1,08</td><td>1,14</td><td>1,2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101203"></a>30</td><td>0,78</td><td>0,88</td><td>0,97</td><td>1,04</td><td>1,1</td><td>1,17</td><td>1,23</td><td>1,3</td><td>1,36</td><td>1,42</td><td>1,49</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101204"></a>45</td><td>0,84</td><td>0,95</td><td>1,05</td><td>1,13</td><td>1,19</td><td>1,27</td><td>1,33</td><td>1,4</td><td>1,47</td><td>1,53</td><td>1,6</td><td>1,68</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101205"></a>60</td><td>0,89</td><td>1,01</td><td>1,11</td><td>1,19</td><td>1,26</td><td>1,34</td><td>1,4</td><td>1,48</td><td>1,55</td><td>1,62</td><td>1,7</td><td>1,77</td><td>1,85</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101206"></a>80</td><td>0,94</td><td>1,06</td><td>1,17</td><td>1,26</td><td>1,33</td><td>1,41</td><td>1,48</td><td>1,57</td><td>1,64</td><td>1,71</td><td>1,79</td><td>1,87</td><td>1,95</td><td>2,02</td><td>2,1</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101207"></a>100</td><td>0,98</td><td>1,1</td><td>1,22</td><td>1,31</td><td>1,38</td><td>1,47</td><td>1,55</td><td>1,63</td><td>1,7</td><td>1,79</td><td>1,87</td><td>1,95</td><td>2,04</td><td>2,11</td><td>2,19</td><td>2,28</td><td>2,36</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101208"></a>125</td><td>1,02</td><td>1,16</td><td>1,28</td><td>1,37</td><td>1,44</td><td>1,54</td><td>1,62</td><td>1,7</td><td>1,78</td><td>1,86</td><td>1,95</td><td>2,04</td><td>2,12</td><td>2,2</td><td>2,29</td><td>2,38</td><td>2,46</td><td>2,54</td><td>-</td><td>-</td></tr>
<tr><td><a id="p101209"></a>160</td><td>1,07</td><td>1,21</td><td>1,34</td><td>1,43</td><td>1,51</td><td>1,61</td><td>1,69</td><td>1,79</td><td>1,87</td><td>1,95</td><td>2,04</td><td>2,13</td><td>2,2</td><td>2,3</td><td>2,4</td><td>2,49</td><td>2,58</td><td>2,66</td><td>2,76</td><td>2,86</td></tr>
<tr><td><a id="p101210"></a>200</td><td>1,12</td><td>1,27</td><td>1,4</td><td>1,49</td><td>1,58</td><td>1,68</td><td>1,77</td><td>1,86</td><td>1,95</td><td>2,04</td><td>2,13</td><td>2,22</td><td>2,32</td><td>2,4</td><td>2,5</td><td>2,6</td><td>2,69</td><td>2,78</td><td>2,88</td><td>2,98</td></tr>
<tr><td><a id="p101211"></a>250</td><td>1,17</td><td>1,32</td><td>1,46</td><td>1,56</td><td>1,65</td><td>1,75</td><td>1,84</td><td>1,94</td><td>2,03</td><td>2,13</td><td>2,22</td><td>2,32</td><td>2,42</td><td>2,51</td><td>2,61</td><td>2,71</td><td>2,8</td><td>2,9</td><td>3</td><td>3,11</td></tr>
<tr><td><a id="p101212"></a>320</td><td>1,22</td><td>1,38</td><td>1,53</td><td>1,63</td><td>1,73</td><td>1,84</td><td>1,93</td><td>2,04</td><td>2,13</td><td>2,22</td><td>2,33</td><td>2,43</td><td>2,54</td><td>2,63</td><td>2,73</td><td>2,84</td><td>2,94</td><td>3,04</td><td>3,17</td><td>3,26</td></tr>
<tr><td><a id="p101213"></a>400</td><td>1,28</td><td>1,44</td><td>1,59</td><td>1,7</td><td>1,8</td><td>1,92</td><td>2,01</td><td>2,13</td><td>2,22</td><td>2,32</td><td>2,43</td><td>2,54</td><td>2,65</td><td>2,74</td><td>2,85</td><td>2,96</td><td>3,07</td><td>3,17</td><td>3,29</td><td>3,4</td></tr>
<tr><td><a id="p101214"></a>Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td>т</td><td>у</td><td>ф</td></tr>
</table>







<table>
<colgroup><col width="21%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="4%"><col width="4%"><col width="9%"></colgroup>
<tr><td colspan="7" rowspan="2"><a id="p101215"></a>Рекомендации по выбору диаметров консольной части борштанг</td><td colspan="4">Приложение 3</td></tr>
<tr><td colspan="2">Лист 1</td><td colspan="2">Листов 2</td></tr>
<tr><td><a id="p101216"></a>Обрабатываемый материал</td><td colspan="3">Чугун, бронза</td><td colspan="3">Алюминий, латунь</td><td colspan="4">Сталь</td></tr>
<tr><td><a id="p101217"></a>L/D</td><td>&lt; 2</td><td>2 - 4</td><td>&gt; 4</td><td>&lt; 2</td><td>2 - 4</td><td>&gt; 4</td><td>&lt; 2</td><td colspan="2">2 - 4</td><td>&gt; 4</td></tr>
<tr><td><a id="p101218"></a>Диаметр растачиваемого отверстия, мм, до</td><td colspan="10">Диаметр борштанги, мм</td></tr>
<tr><td><a id="p101219"></a>12</td><td>11</td><td>10,5</td><td>10</td><td>10,5</td><td>10</td><td>9,5</td><td>10</td><td colspan="2">10</td><td>9,5</td></tr>
<tr><td><a id="p101220"></a>13</td><td>12</td><td>11,5</td><td>11</td><td>11,5</td><td>11</td><td>10,5</td><td>11</td><td colspan="2">11</td><td>10,5</td></tr>
<tr><td><a id="p101221"></a>14</td><td>13</td><td>12,5</td><td>12</td><td>12,5</td><td>12</td><td>11,5</td><td>12</td><td colspan="2">12</td><td>11,5</td></tr>
<tr><td><a id="p101222"></a>15</td><td>14</td><td>13</td><td>13</td><td>13</td><td>12,5</td><td>12</td><td>12,5</td><td colspan="2">12,5</td><td>12</td></tr>
<tr><td><a id="p101223"></a>16</td><td>15</td><td>14</td><td>14</td><td>14</td><td>13,5</td><td>12</td><td>13,5</td><td colspan="2">13</td><td>12,5</td></tr>
<tr><td><a id="p101224"></a>17</td><td>15,5</td><td>14,5</td><td>14</td><td>14,5</td><td>14</td><td>13</td><td>14</td><td colspan="2">13</td><td>13</td></tr>
<tr><td><a id="p101225"></a>18</td><td>16</td><td>15,5</td><td>15</td><td>15,5</td><td>15</td><td>14</td><td>15</td><td colspan="2">14</td><td>14</td></tr>
<tr><td><a id="p101226"></a>19</td><td>17</td><td>16,5</td><td>16</td><td>16,5</td><td>16</td><td>15</td><td>16</td><td colspan="2">15</td><td>15</td></tr>
<tr><td><a id="p101227"></a>20</td><td>18</td><td>17,5</td><td>17</td><td>17,5</td><td>17</td><td>16</td><td>17</td><td colspan="2">16</td><td>15</td></tr>
<tr><td><a id="p101228"></a>21</td><td>19</td><td>18</td><td>17,5</td><td>18,5</td><td>17,5</td><td>17</td><td>17,5</td><td colspan="2">17</td><td>16</td></tr>
<tr><td><a id="p101229"></a>22</td><td>20</td><td>19</td><td>18</td><td>19</td><td>18</td><td>18</td><td>18</td><td colspan="2">17</td><td>17</td></tr>
<tr><td><a id="p101230"></a>24</td><td>22</td><td>21</td><td>19,5</td><td>21</td><td>19,5</td><td>19</td><td>19,5</td><td colspan="2">19</td><td>18</td></tr>
<tr><td><a id="p101231"></a>25</td><td>22</td><td>21,5</td><td>20,5</td><td>21,5</td><td>20,5</td><td>20</td><td>20,5</td><td colspan="2">20</td><td>19</td></tr>
<tr><td><a id="p101232"></a>26</td><td>23</td><td>22</td><td>21,5</td><td>22</td><td>21,5</td><td>21</td><td>21,5</td><td colspan="2">21</td><td>20</td></tr>
<tr><td><a id="p101233"></a>28</td><td>25</td><td>24</td><td>23</td><td>24</td><td>23</td><td>22</td><td>23</td><td colspan="2">22</td><td>21</td></tr>
<tr><td><a id="p101234"></a>30</td><td>26</td><td>25</td><td>25</td><td>26</td><td>25</td><td>24</td><td>25</td><td colspan="2">24</td><td>22</td></tr>
<tr><td><a id="p101235"></a>32</td><td>28</td><td>28</td><td>27</td><td>28</td><td>27</td><td>25</td><td>27</td><td colspan="2">25</td><td>24</td></tr>
<tr><td><a id="p101236"></a>34</td><td>30</td><td>30</td><td>28</td><td>30</td><td>28</td><td>26</td><td>28</td><td colspan="2">26</td><td>25</td></tr>
<tr><td><a id="p101237"></a>36</td><td>32</td><td>32</td><td>30</td><td>32</td><td>30</td><td>28</td><td>30</td><td colspan="2">28</td><td>26</td></tr>
<tr><td><a id="p101238"></a>38</td><td>34</td><td>34</td><td>31</td><td>34</td><td>31</td><td>30</td><td>31</td><td colspan="2">30</td><td>28</td></tr>
<tr><td><a id="p101239"></a>40</td><td>36</td><td>35</td><td>33</td><td>34</td><td>33</td><td>32</td><td>33</td><td colspan="2">31</td><td>30</td></tr>
<tr><td><a id="p101240"></a>42</td><td>38</td><td>37</td><td>35</td><td>36</td><td>35</td><td>34</td><td>35</td><td colspan="2">34</td><td>32</td></tr>
<tr><td><a id="p101241"></a>45</td><td>41</td><td>40</td><td>38</td><td>39</td><td>38</td><td>35</td><td>38</td><td colspan="2">35</td><td>34</td></tr>
<tr><td><a id="p101242"></a>48</td><td>44</td><td>43</td><td>40</td><td>42</td><td>40</td><td>38</td><td>40</td><td colspan="2">38</td><td>36</td></tr>
<tr><td><a id="p101243"></a>50</td><td>46</td><td>45</td><td>42</td><td>44</td><td>42</td><td>40</td><td>42</td><td colspan="2">40</td><td>38</td></tr>
<tr><td><a id="p101244"></a>56</td><td>52</td><td>51</td><td>48</td><td>48</td><td>48</td><td>45</td><td>48</td><td colspan="2">45</td><td>42</td></tr>
<tr><td><a id="p101245"></a>60</td><td>56</td><td>54</td><td>52</td><td>52</td><td>52</td><td>48</td><td>52</td><td colspan="2">48</td><td>45</td></tr>
<tr><td><a id="p101246"></a>67</td><td>62</td><td>61</td><td>58</td><td>58</td><td>58</td><td>55</td><td>58</td><td colspan="2">55</td><td>52</td></tr>
<tr><td><a id="p101247"></a>71</td><td>65</td><td>63</td><td>62</td><td>62</td><td>62</td><td>58</td><td>62</td><td colspan="2">60</td><td>58</td></tr>
<tr><td><a id="p101248"></a>75</td><td>67</td><td>67</td><td>65</td><td>65</td><td>65</td><td>60</td><td>65</td><td colspan="2">60</td><td>60</td></tr>
<tr><td><a id="p101249"></a>80</td><td>71</td><td>71</td><td>70</td><td>70</td><td>70</td><td>65</td><td>70</td><td colspan="2">65</td><td>60</td></tr>
<tr><td><a id="p101250"></a>85</td><td>75</td><td>75</td><td>75</td><td>75</td><td>75</td><td>70</td><td>75</td><td colspan="2">70</td><td>65</td></tr>
</table>



<table>
<colgroup><col width="21%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="9%"><col width="4%"><col width="4%"><col width="9%"></colgroup>
<tr><td colspan="7" rowspan="2"><a id="p101251"></a>Рекомендации по выбору диаметров консольной части борштанг</td><td colspan="4">Приложение 3</td></tr>
<tr><td colspan="2">Лист 2</td><td colspan="2">Листов 2</td></tr>
<tr><td><a id="p101252"></a>Обрабатываемый материал</td><td colspan="3">Чугун, бронза</td><td colspan="3">Алюминий, латунь</td><td colspan="4">Сталь</td></tr>
<tr><td><a id="p101253"></a>L/D</td><td>&lt; 2</td><td>2 - 4</td><td>&gt; 4</td><td>&lt; 2</td><td>2 - 4</td><td>&gt; 4</td><td>&lt; 2</td><td colspan="2">2 - 4</td><td>&gt; 4</td></tr>
<tr><td><a id="p101254"></a>Диаметр растачиваемого отверстия, мм, до</td><td colspan="10">Диаметр борштанги, мм</td></tr>
<tr><td><a id="p101255"></a>90</td><td>80</td><td>80</td><td>80</td><td>80</td><td>80</td><td>75</td><td>80</td><td colspan="2">75</td><td>70</td></tr>
<tr><td><a id="p101256"></a>95</td><td>85</td><td>85</td><td>85</td><td>85</td><td>85</td><td>80</td><td>85</td><td colspan="2">80</td><td>75</td></tr>
<tr><td><a id="p101257"></a>100</td><td>90</td><td>90</td><td>90</td><td>90</td><td>90</td><td>85</td><td>90</td><td colspan="2">85</td><td>80</td></tr>
<tr><td><a id="p101258"></a>110</td><td>100</td><td>100</td><td>95</td><td>95</td><td>95</td><td>90</td><td>95</td><td colspan="2">90</td><td>90</td></tr>
<tr><td><a id="p101259"></a>120</td><td>110</td><td>110</td><td>105</td><td>105</td><td>105</td><td>100</td><td>105</td><td colspan="2">100</td><td>100</td></tr>
<tr><td><a id="p101260"></a>125</td><td>115</td><td>115</td><td>110</td><td>110</td><td>110</td><td>105</td><td>110</td><td colspan="2">105</td><td>105</td></tr>
<tr><td><a id="p101261"></a>130</td><td>120</td><td>120</td><td>115</td><td>120</td><td>115</td><td>110</td><td>110</td><td colspan="2">110</td><td>110</td></tr>
<tr><td><a id="p101262"></a>140</td><td>130</td><td>125</td><td>120</td><td>125</td><td>120</td><td>120</td><td>120</td><td colspan="2">120</td><td>120</td></tr>
<tr><td><a id="p101263"></a>150</td><td>135</td><td>135</td><td>130</td><td>130</td><td>130</td><td>130</td><td>130</td><td colspan="2">130</td><td>130</td></tr>
<tr><td><a id="p101264"></a>160</td><td>145</td><td>145</td><td>140</td><td>140</td><td>140</td><td>140</td><td>140</td><td colspan="2">130</td><td>130</td></tr>
<tr><td><a id="p101265"></a>170</td><td>155</td><td>155</td><td>150</td><td>150</td><td>150</td><td>150</td><td>150</td><td colspan="2">140</td><td>140</td></tr>
<tr><td><a id="p101266"></a>180</td><td>165</td><td>165</td><td>160</td><td>160</td><td>160</td><td>160</td><td>160</td><td colspan="2">150</td><td>150</td></tr>
<tr><td><a id="p101267"></a>190</td><td>175</td><td>175</td><td>170</td><td>170</td><td>170</td><td>170</td><td>170</td><td colspan="2">160</td><td>160</td></tr>
<tr><td><a id="p101268"></a>200</td><td>185</td><td>185</td><td>175</td><td>180</td><td>185</td><td>180</td><td>175</td><td colspan="2">170</td><td>170</td></tr>
<tr><td><a id="p101269"></a>210</td><td>195</td><td>195</td><td>185</td><td>190</td><td>185</td><td>190</td><td>185</td><td colspan="2">180</td><td>180</td></tr>
<tr><td><a id="p101270"></a>220</td><td>205</td><td>205</td><td>195</td><td>200</td><td>195</td><td>200</td><td>195</td><td colspan="2">190</td><td>190</td></tr>
<tr><td><a id="p101271"></a>240</td><td>220</td><td>220</td><td>215</td><td>220</td><td>215</td><td>220</td><td>215</td><td colspan="2">210</td><td>210</td></tr>
<tr><td><a id="p101272"></a>250</td><td>230</td><td>230</td><td>220</td><td>230</td><td>220</td><td>220</td><td>220</td><td colspan="2">220</td><td>220</td></tr>
</table>




<a id="p101273"></a>

---