---
title: "\"Общемашиностроительные укрупненные нормативы времени на работы, выполняемые на металлорежущих станках. Единичное, мелкосерийное и среднесерийное производство. Часть V. Горизонтально-расточные станки\""
issuer: "Государственный комитет СССР по труду и социальным вопросам"
status: утратил силу
canonical: "https://bukva.ai/docs/obschemashinostroitelnye-ukrupnennye-normativy-goskomtrud-sssr-7"
---

## "Общемашиностроительные укрупненные нормативы времени на работы, выполняемые на металлорежущих станках. Единичное, мелкосерийное и среднесерийное производство. Часть V. Горизонтально-расточные станки"

# "Общемашиностроительные укрупненные нормативы времени на работы, выполняемые на металлорежущих станках. Единичное, мелкосерийное и среднесерийное производство. Часть V. Горизонтально-расточные станки"

(утв. Госкомтрудом СССР)

> [!WARNING]
> Документ утратил силу на территории Российской Федерации в связи с изданием Приказа Минтруда России от 03.12.2020 N 850.
> В соответствии с Трудовым кодексом РФ системы нормирования труда определяются работодателем с учетом мнения представительного органа работников или устанавливаются коллективным договором. Для однородных работ могут разрабатываться и устанавливаться типовые (межотраслевые, отраслевые, профессиональные и иные) нормы труда в соответствии с Правилами, утвержденными Постановлением Правительства РФ от 11.11.2002 N 804.


<a id="p100001"></a>**ОБЩЕМАШИНОСТРОИТЕЛЬНЫЕ УКРУПНЕННЫЕ НОРМАТИВЫ ВРЕМЕНИ**
**НА РАБОТЫ, ВЫПОЛНЯЕМЫЕ НА МЕТАЛЛОРЕЖУЩИХ СТАНКАХ**

<a id="p100002"></a>**ЕДИНИЧНОЕ, МЕЛКОСЕРИЙНОЕ И СРЕДНЕСЕРИЙНОЕ ПРОИЗВОДСТВО**

<a id="p100003"></a>**ЧАСТЬ V. ГОРИЗОНТАЛЬНО-РАСТОЧНЫЕ СТАНКИ**

<a id="p100004"></a>Сборник содержит нормативы подготовительно-заключительного времени, времени на установку и снятие детали, укрупненные нормативы неполного штучного времени на проход для условий единичного и мелкосерийного производства и нормативы времени на обработку единицы длины поверхности для участков со среднесерийным типом производства, выполняемых на горизонтально-расточных станках.
<a id="p100005"></a>Настоящий сборник предназначен для нормировщиков, технологов и других инженерно-технических работников, занятых разработкой технически обоснованных норм времени на станочные работы в условиях единичного, мелкосерийного и на участках со среднесерийным типом производства.
<a id="p100006"></a>Нормативы рекомендованы ЦБНТ для применения на предприятиях машиностроения и металлообработки.
<a id="p100007"></a>Настоящие нормативы разработаны ЦПКТБ Системпроект Минлетпищемаша под методическим руководством Центрального бюро нормативов по труду при Всесоюзном научно-методическом центре по организации труда и управления производством Государственного комитета СССР по труду и социальным вопросам при участии нормативно-исследовательских организаций и предприятий машиностроительных министерств.
<a id="p100008"></a>С введением в действие данных нормативов отменяются Общемашиностроительные укрупненные [нормативы](https://bukva.ai/docs/obschemashinostroitelnye-ukrupnennye-normativy-goskomtrud-sssr-9) времени на работы, выполняемые на металлорежущих станках. Мелкосерийное, единичное производство. Часть III. Горизонтально-расточные, зуборезные, резьбонакатные и заготовительные работы (резка металла на дисковых пилах, прессах и сортовых ножницах), М.; Машиностроение, 1975.
<a id="p100009"></a>Обеспечение межотраслевыми нормативными материалами по труду осуществляется по "Книготорговому бюллетеню" или Аннотированному плану выпуска литературы издательства "Экономика" через книготорговую сеть на местах по заявкам предприятий и организаций.


### 1. <a id="p100010"></a>ОБЩАЯ ЧАСТЬ


<a id="p100011"></a>1.1. Укрупненные нормативы времени разработаны для нормирования станочных работ в условиях единичного, мелкосерийного и на участках со среднесерийным типом производства.
<a id="p100012"></a>1.2. При внедрении бригадной организации труда нормативы могут быть использованы для расчета комплексных норм в соответствии с "Методическими основами бригадной формы организации и стимулирования труда в промышленности", разработанными НИИ труда в 1981 г. и одобренными Научным советом по труду и социальным вопросам Госкомтруда СССР.
<a id="p100013"></a>1.3. Сборник содержит нормативы подготовительно-заключительного времени, времени на установку и снятие детали, укрупненные нормативы неполного штучного времени на переход для условий единичного и мелкосерийного производства и нормативы времени на обработку единицы длины поверхности для участков со среднесерийным типом производства, выполняемых на горизонтально-расточных станках.

#### <a id="p100014"></a>1.4 В сборник включен ряд приложений, содержащих справочный материал:

<a id="p100015"></a>Механические свойства основных конструкционных углеродистых и легированных сталей, чугуна и медных сплавов;
<a id="p100016"></a>Приемы, включенные в комплексы вспомогательного времени, связанного с обработкой поверхности.
<a id="p100017"></a>Приведены числовые величины вспомогательного времени, связанного с переходом, включенного в состав нормативов неполного штучного времени; величины врезания и перебега инструментов.

#### <a id="p100018"></a>1.5 При разработке нормативов в качестве исходных данных были использованы следующие материалы:

<a id="p100019"></a>Общемашиностроительные нормативы времени вспомогательного, на обслуживание рабочего места и подготовительно-заключительного при работе на металлорежущих станках. Мелкосерийное и единичное производство;
<a id="p100020"></a>Общемашиностроительные [нормативы](https://bukva.ai/docs/obschemashinostroitelnye-normativy-vremeni-goskomtrud-sssr-2) времени вспомогательного, на обслуживание рабочего места и подготовительно-заключительного при работе на металлорежущих станках. Среднесерийное и крупносерийное производство;
<a id="p100021"></a>Общемашиностроительные нормативы режимов резания для технического нормирования работ на металлорежущих станках. Часть 1;
<a id="p100022"></a>данные фотохронометражных наблюдений, результаты анализа трудового процесса, рациональных методов труда и организации рабочего места;
<a id="p100023"></a>техническая литература и паспортные данные металлорежущих станков.
<a id="p100024"></a>1.6. Нормативы рассчитаны на использование их в основных и вспомогательных цехах машиностроительных и металлообрабатывающих заводов по различным типам производств.
<a id="p100025"></a>    Тип  производства  характеризуется  коэффициентом  закрепления операций
(К   ) в соответствии с ГОСТ 3.1108-74.
  з.о
<a id="p100026"></a>    Коэффициент  закрепления  операций  есть отношение числа всех различных
технологических  операций,  выполненных или подлежащих выполнению в течение
месяца, к числу рабочих мест и определяется по формуле:

                                        О
<a id="p100027"></a>                                 К    = -,
                                  з.о   Р

    где:
<a id="p100028"></a>    О - число различных операций;
<a id="p100029"></a>    Р - число рабочих мест.
<a id="p100030"></a>    В соответствии с указанным ГОСТом этот коэффициент принимается равным:
<a id="p100031"></a>    20 < К    < 40 - мелкосерийное производство;
          з.о
<a id="p100032"></a>    10 < К    < 20 - среднесерийное производство;
          з.о
<a id="p100033"></a>    К    не регламентируется - единичное производство.
     з.о
<a id="p100034"></a>Мелкосерийное и единичное производство характеризуется широкой номенклатурой изготовляемых изделий и малым объемом их выпуска.
<a id="p100035"></a>Обработка деталей производится преимущественно на универсальном оборудовании с применением универсальных, нормализованных и специальных приспособлений и инструментов.
<a id="p100036"></a>Наряды на работу, технологическую документацию, инструмент и приспособления получает сам рабочий и доставляет на рабочее место.
<a id="p100037"></a>Заготовки на рабочее место доставляются вспомогательными рабочими.
<a id="p100038"></a>Заточка инструмента централизована.
<a id="p100039"></a>Станки, обрабатывающие тяжелые детали, оборудованы подъемно-транспортными средствами.
<a id="p100040"></a>Среднесерийное производство характеризуется ограниченной номенклатурой изделий, изготовляемых периодически повторяющимися партиями, и сравнительно большим объемом их выпуска. Обработка деталей производится преимущественно на универсальном оборудовании с применением универсальных, нормализованных и специальных приспособлений и инструментов. Детали, сходные по конструктивным и технологическим признакам, закреплены за группой станков, имеющих одинаковые эксплуатационные характеристики. Продолжительность цикла работы станка между двумя переналадками при обработке партии деталей средних размеров составляет по времени 0,25 - 4 рабочие смены. За рабочим местом закреплено 11 - 20 операций.
<a id="p100041"></a>Обработка на станках выполняется на основании подробно разработанных технологических карт с указанием режимов работы оборудования, времени выполнения каждого перехода и нормы штучного времени.
<a id="p100042"></a>Наряды на работу, технологическая документация, заготовки, предусмотренные технологией, инструменты и приспособления доставляются к рабочему месту вспомогательными рабочими.
<a id="p100043"></a>Инструмент затачивается в централизованном порядке.
<a id="p100044"></a>Станки, обрабатывающие тяжелые детали, оборудованы подъемно-транспортными средствами.
<a id="p100045"></a>Рабочее место обеспечено необходимым комплектом приспособлений, способствующих сокращению вспомогательного времени.
<a id="p100046"></a>Нормативы времени рассчитаны на одноинструментную обработку в условиях одностаночного обслуживания.


#### <a id="p100047"></a>1.7 НОРМА ВРЕМЕНИ И ЕЕ СОСТАВЛЯЮЩИЕ


<a id="p100048"></a>    Норма  времени  на  выполнение  станочной  операции  состоит  из  нормы
подготовительно-заключительного  времени  (t   )  и  нормы штучного времени
                                            п.з
(T ) и определяется по формуле:
  ш

                                        t
                                         п.з
<a id="p100049"></a>                             Н   = Т  + ----.                         (1.1)
                              вр    ш    q

<a id="p100050"></a>    Для  единичного  и  мелкосерийного  типа  производства  норма  штучного
времени  определяется  путем  суммирования  времени  на  установку и снятие
детали  и  неполного  штучного  времени  на обработку поверхностей с учетом
числа проходов:

<a id="p100051"></a>    Т  = [t    + (t    i  + t    i  + ... + t    i )] К   (мин.).     (1.2)
     ш     в.у     н.ш  1    н.ш  2          н.ш  n    Тш
                      1         2               n

<a id="p100052"></a>    Для   среднесерийного   типа   производства   норма   штучного  времени
определяется по формуле:

             l                            l
              1                            2
<a id="p100053"></a>    Т  = [(------- х t           х i  + ------- х t           х i  + ... +
     ш     100(10)    о 100(10)     1   100(10)    о 100(10)     2
                               1                            2

        l
         n
    + ------- х t           х i ) + (t    + t    х i  + t    х i  + ... +
      100(10)    о 100(10)     n      в.у    вп     1    вп     2
                          n                    1           2

                                             а    + а
                                              обс    отд
                 + t    х i ) х К   ] х (1 + -----------),
                    вп     n     t.в             100
                      n

    где:
<a id="p100054"></a>    Н   - норма времени, мин.;
     вр
<a id="p100055"></a>    Т  - норма штучного времени, мин.;
     ш
<a id="p100056"></a>    t    - норматив подготовительно-заключительного времени, мин.;
     п.з
<a id="p100057"></a>    t    ,  t    ,  t     - укрупненный норматив неполного штучного времени
     н.ш     н.ш     н.ш
        1       2       n
на обработку поверхности, мин.;
<a id="p100058"></a>    t     - норматив вспомогательного времени на установку и снятие детали,
     в.у
мин.;
<a id="p100059"></a>    t   ,  t   ,  t     -  норматив  вспомогательного времени, связанного с
     вп     вп     вп
       1      2      n
переходом, мин.;
<a id="p100060"></a>    t          ,  t          ,  t           - основное время  на  обработку
     о 100(10)     о 100(10)     о 100(10)
              1             2             n
100(10) мм длины обрабатываемой поверхности, мин.;
<a id="p100061"></a>    l , l , l  - расчетная длина обрабатываемой поверхности, мм;
     1   2   n
<a id="p100062"></a>    i - число проходов;
<a id="p100063"></a>    К    -  коэффициент  к  норме  штучного времени в зависимости от партии
     Тш
деталей в единичном и мелкосерийном производстве;
<a id="p100064"></a>    К     -   коэффициент  к  вспомогательному  времени  в  зависимости  от
     t.в
характера серийности работ в среднесерийном производстве;
<a id="p100065"></a>    q - число деталей в партии, шт.;
<a id="p100066"></a>    а     -  время  на  обслуживание  рабочего  места  в  % от оперативного
     обс
времени;
<a id="p100067"></a>    а    - время на отдых и личные потребности в % от оперативного времени.
     отд
<a id="p100068"></a>Необходимым условием, определяющим возможность расчета технически обоснованных норм времени по данным нормативам, является наличие предварительно разработанного маршрутного технологического процесса по операциям с указанием в нем обрабатываемых поверхностей, их размеров и характера обработки.
<a id="p100069"></a>Нормативы подготовительно-заключительного времени предусматривают выполнение следующих работ:
<a id="p100070"></a>получение наряда и технологической документации;
<a id="p100071"></a>ознакомление с работой, чертежом и получение инструктажа;
<a id="p100072"></a>получение недостающих на рабочем месте инструментов и приспособлений;
<a id="p100073"></a>подготовка рабочего места, наладка и переналадка оборудования, инструментов и приспособлений;
<a id="p100074"></a>снятие инструментов и приспособлений по окончании обработки партии деталей и другие подготовительно-заключительные работы, связанные с изготовлением данной партии деталей.
<a id="p100075"></a>Нормативы подготовительно-заключительного времени приведены в виде укрупненных комплексов приемов работы.
<a id="p100076"></a>Кроме этого, в картах приведены нормативы времени на выполнение отдельных приемов подготовительно-заключительной работы, не включенных в комплексы, но которые могут иметь место в отдельных случаях.
<a id="p100077"></a>В качестве основных факторов, определяющих продолжительность подготовительно-заключительного времени, в нормативах учтены:
<a id="p100078"></a>тип и основные размерные характеристики станков;
<a id="p100079"></a>способ установки детали и характер применяемых приспособлений;
<a id="p100080"></a>число инструментов, участвующих в работе;
<a id="p100081"></a>замена установочных приспособлений.
<a id="p100082"></a>Кроме перечисленных выше факторов продолжительности, учтена также степень сложности подготовки к работе - простая, средняя и сложная:
<a id="p100083"></a>при простой подготовке требуется беглое изучение чертежей и технологического процесса; работа выполняется без частичных переналадок;
<a id="p100084"></a>при подготовке средней сложности требуется изучение чертежа и технологического процесса; необходимо получение краткого инструктажа от мастера; производится одна частичная переналадка оборудования в процессе обработки партии деталей;
<a id="p100085"></a>при сложной подготовке требуется тщательное изучение чертежа и технологического процесса, необходим подробный инструктаж мастера; производятся две-три частичные переналадки оборудования.
<a id="p100086"></a>В случае когда на станке систематически выполняются однотипные операции по обработке конструктивно сходных деталей, подготовительно-заключительное время должно быть уменьшено по сравнению с нормативным на 30 - 50%. В условиях бригадной формы организации труда, когда производится межсменная передача обрабатываемых изделий, подготовительно-заключительное время должно быть уменьшено на 30 - 50%.
<a id="p100087"></a>В нормативах вспомогательного времени на установку и снятие детали (карты 3, 94) предусмотрены все типовые способы установки, выверки и крепления детали. В качестве фактора продолжительности времени установки принимается масса детали и способ ее крепления, тип приспособления, характер выверки, установочной поверхности и др.
<a id="p100088"></a>Время на установку приведено укрупненно на комплексы приемов.
<a id="p100089"></a>При работе с заготовками в комплексы включены приемы: установить деталь, выверить и закрепить ее, включить и выключить станок, открепить деталь, снять ее, очистить приспособление от стружки.
<a id="p100090"></a>Кроме перечисленных основных приемов, в состав комплексов включены также приемы: при работе с краном - вызвать кран, застропить деталь и отстропить деталь.
<a id="p100091"></a>Нормативами предусматривается установка и снятие детали массой до 20 кг вручную и свыше 20 кг с помощью подъемных механизмов.
<a id="p100092"></a>Установка вручную деталей массой свыше 20 кг приведена в нормативах для пользования в отдельных случаях при обработке на участках, где отсутствуют подъемно-транспортные средства.
<a id="p100093"></a>Для работ, выполняемых с помощью подъемных механизмов, в нормативах предусматривается применение двух видов подъемных устройств:
<a id="p100094"></a>подъемника при станке (или группе станков), обслуживаемого самим исполнителем работы;
<a id="p100095"></a>мостового крана.
<a id="p100096"></a>В последнем случае нормативами учтено время на вызов крана в размере 1 - 5 мин.
<a id="p100097"></a>В целях упрощения расчетов время на установку и снятие детали для мелкосерийного и единичного производства (карта 3) приведено с учетом времени на обслуживание рабочего места, перерывы на отдых и личные потребности.
<a id="p100098"></a>    Нормативы неполного штучного времени включают: t  - основное время; t
                                                    о                    вп
-  вспомогательное  время, связанное с переходом, время на изменение режима
работы  станка  и  смену инструмента; t    - время на обслуживание рабочего
                                       обс
места, перерывы на отдых и личные потребности.
<a id="p100099"></a>Основное время рассчитывалось на основе режимов резания по общемашиностроительным нормативам режимов резания с учетом технологических факторов, влияющих на режим и время обработки.
<a id="p100100"></a>Принятые при расчете основного времени режимы резания приведены в картах нормативов.
<a id="p100101"></a>Режимы резания установлены применительно к условиям обработки универсальными режущими инструментами из наиболее часто применяемых марок инструментальных материалов на распространенном в мелкосерийном, единичном и среднесерийном производстве оборудовании. При этом учитывались мощность оборудования, прочность режущего инструмента, прочность и жесткость системы "станок - приспособление - инструмент - деталь" и другие факторы.
<a id="p100102"></a>Нормативы времени при черновом растачивании отверстий приведены для жесткой системы. При нежесткой системе допускается применение поправочного коэффициента К до 1,25.
<a id="p100103"></a>Неполное штучное время на обработку поверхности в нормативах приведено на один проход применительно к различным значениям глубины резания.
<a id="p100104"></a>Вспомогательное время, связанное с переходом, принятое при расчете неполного штучного времени, установлено по Общемашиностроительным нормативам времени вспомогательного, на обслуживание рабочего места и подготовительно-заключительного при работе на металлорежущих станках. Мелкосерийное и единичное производство.
<a id="p100105"></a>При определении числовых величин наряду с приемами, повторяющимися с каждым переходом, были учтены приемы, не вошедшие в комплекс вспомогательного времени (изменение режима работы, смена инструмента и т.д.).
<a id="p100106"></a>Время на обслуживание рабочего места, отдых и личные потребности включено в неполное штучное время в соответствии с таблицей.

<div align="center">

<a id="p100107"></a>**ВРЕМЯ НА ОБСЛУЖИВАНИЕ РАБОЧЕГО МЕСТА,**<br>
**ОТДЫХ И ЛИЧНЫЕ НАДОБНОСТИ**

</div>



<table>
<colgroup><col width="48%"><col width="25%"><col width="28%"></colgroup>
<tr><td rowspan="2">Наименование станков</td><td colspan="2">Время в % от оперативного времени</td></tr>
<tr><td>на обслуживание рабочего места</td><td>на отдых и личные потребности</td></tr>
<tr><td>Горизонтально-расточные станки</td><td>5,5</td><td>4</td></tr>
</table>


<a id="p100110"></a>Неполное штучное время в картах нормативов рассчитано для определенных технологических условий выполнения работы. Для случаев обработки, отличных от принятых при расчете нормативов, в картах приводятся поправочные коэффициенты на неполное штучное время, учитывающие другие условия выполнения работ.
<a id="p100111"></a>    Норма   штучного   времени,   установленная  по  настоящим  нормативам,
принимается  с  коэффициентом в зависимости от партии деталей в единичном и
мелкосерийном  производстве  (К  ).  Поправочные  коэффициенты  приведены в
                               Тш
карте 1.
<a id="p100112"></a>Время на обработку единицы длины поверхности включает в себя основное время на обработку 100(10) мм расчетной длины обрабатываемой поверхности.
<a id="p100113"></a>Нормативы предусматривают обработку деталей из стали, чугуна, медных и алюминиевых сплавов различных марок на станках различной мощности.
<a id="p100114"></a>Режущий инструмент для обработки деталей - сверла, зенкеры, развертки, цековки с пластинками Т15К6, Т5К10, ВК6, ВК8 и др., а также из стали Р6М5.
<a id="p100115"></a>Особое внимание уделено выбору рациональной глубины резания, величины подачи и частоты вращения.
<a id="p100116"></a>Глубина резания принята с учетом припуска на обработку соответственно ГОСТ 1855-55 на литье и ГОСТ 7062-79 на поковки.
<a id="p100117"></a>В картах нормативов для каждого параметра обрабатываемой поверхности приводятся различные значения глубины резания, что дает возможность рассчитать норму времени при оптимальном числе проходов.
<a id="p100118"></a>Вспомогательное время, связанное с переходом, не включенное в комплексы, приведено отдельно (карта 5).
<a id="p100119"></a>    Вспомогательное  время при расчете нормы штучного времени принимается с
коэффициентом  в зависимости от характера серийности работ в среднесерийном
производстве  (К   ). При внедрении на предприятии более прогрессивной, чем
                t.в
предусмотрено   в   настоящем   сборнике,   организации  труда,  технологии
выполнения  работ,  более эффективного оборудования, механизмов, оснастки и
т.п.  следует  разрабатывать  и  вводить  в  установленном  порядке местные
нормативы времени, соответствующие более высокой производительности труда.


#### <a id="p100120"></a>1.8 ПРИМЕРЫ РАСЧЕТА НОРМЫ ВРЕМЕНИ



##### <a id="p100121"></a>1.8.1 ПРИМЕР РАСЧЕТА НОРМЫ ВРЕМЕНИ

<div align="center">

**НА ГОРИЗОНТАЛЬНО-РАСТОЧНОМ СТАНКЕ**

<a id="p100122"></a>Рис. 1.1.<br>
(не приводится)

</div>



###### <a id="p100123"></a>1.8.1.1 Исходные данные


    1. <a id="p100124"></a>Станок - горизонтально-расточный 2622В, N  = 11 кВт.
                                                д
2. <a id="p100125"></a>Деталь - корпус.
3. <a id="p100126"></a>Обрабатываемый материал - чугун серый, НВ = 1,76 - 2,15 ГПа.
4. <a id="p100127"></a>Масса детали - 350 кг.
5. <a id="p100128"></a>Заготовка - отливка.
6. <a id="p100129"></a>Припуск на обработку - до 10 мм.
7. <a id="p100130"></a>Операция - расточная.
8. <a id="p100131"></a>Способ установки детали - на столе с креплением болтами и планками.
9. <a id="p100132"></a>Режущий инструмент - фреза торцовая с пластинками ВК8, резец расточной ВК8.
10. <a id="p100133"></a>Число деталей в партии - 5 шт.


###### <a id="p100134"></a>1.8.1.2 Определение подготовительно-заключительного времени


<a id="p100135"></a>    Подготовительно-заключительное  время  определяется по карте 2, лист 1.
По  технологическому  процессу работа выполняется за один установ детали на
столе с креплением болтами и планками с тремя инструментами в наладке и при
диаметре шпинделя станка d   = 110 мм.
                          шп
<a id="p100136"></a>Подготовительно-заключительное время на наладку средней сложности принимается равным 16 мин. на всю партию деталей (карта 2, поз. 3д).


###### <a id="p100137"></a>1.8.1.3 Определение времени на установку и снятие детали


<a id="p100138"></a>Время на установку и снятие детали определяется по карте 3. При установке детали массой 350 кг на столе с креплением болтами и планками с выверкой в одной плоскости время на установку и снятие детали принимается равным 14 мин. (поз. 3ж).


###### <a id="p100139"></a>1.8.1.4 Определение неполного штучного времени

<div align="center">

на обработку поверхности

</div>


<a id="p100140"></a>Обработка поверхности 2(Rz 80) производится за 1 проход.
<a id="p100141"></a>    При обработке на станке мощностью до 10 кВт, диаметре фрезы D = 200 мм,
глубине  резания  8 мм и длине обработки 90 мм (расчетная длина 108 мм, см.
карту примера расчета нормы времени) t    = 2,4 мин. (карта 52; поз. 12г).
                                      н.ш
<a id="p100142"></a>    Обработка  поверхности  3(Rz  80)  производится  также за 1 проход. При
длине обработки 75 мм t    = 2,1 (карта 52; поз. 12в).
                       н.ш
<a id="p100143"></a>    Условия  обработки поверхности 4 те же, что и поверхности 2, t    = 2,4
                                                                  н.ш
мин.
<a id="p100144"></a>    При  предварительной обработке поверхности 1(Rz 80) торцовой фрезой D =
200  мм  при  ширине  фрезерования  140,  длине  обработки l = 400, глубине
резания 8 мм за 2 прохода t    = 10 мин. (карта 52; поз. 12к).
                           н.ш
<a id="p100145"></a>    При  окончательной обработке поверхности 1(Rz 20) при расчетной длине l
+  l   =  600 мм, глубине резания 3 мм за 2 прохода t    = 11 мм (карта 53;
    1                                                н.ш
поз. 9л).
<a id="p100146"></a>    При обработке поверхности 6(Rz 80) предварительно расточным резцом ВК8,
глубине  резания  6 мм, длине обработки l = 30 мм t    = 1,8 мин. (карта 7;
                                                   н.ш
поз. 14б).
<a id="p100147"></a>    При  окончательной обработке поверхности 6(Ra 2,5) расточным резцом при
глубине резания t = 1 мм t    = 4,55 мин. (карта 10; поз. 6б).
                          н.ш
<a id="p100148"></a>    При предварительной обработке поверхности 5(Rz 80) расточным резцом при
глубине  резания  t  = 5 мм (расчетная длина 80 + 80 + 11) t    = 2,55 мин.
                                                            н.ш
(карта 7; поз. 5ж).
<a id="p100149"></a>    При  окончательной обработке поверхности 5(Ra 2,5), глубине резания t =
1 мм, расчетной длине 80 + 80 + 2 t    = 5,5 мин. (карта 10; поз. 3ж).
                                   н.ш
<a id="p100150"></a>    При  обработке  отверстия  под  резьбу М16 х 1,5 (диам. 14,3 мм), длине
обработки 30 мм t    = 0,63 мин. (карта 82; поз. 4г).
                 н.ш
<a id="p100151"></a>    На обработку фаски 18 х 1,5 t    = 0,35 мин. (карта 92).
                                 н.ш
<a id="p100152"></a>    На нарезание резьбы М16 х 1,5 t    = 1,85 мин. (карта 92; поз. 5д).
                                   н.ш
<a id="p100153"></a>В неполное штучное время необходимо включить вспомогательное время на приемы, связанные с обработкой поверхности, не включенные в комплексы:
<a id="p100154"></a>установить фрезу на оправку - 2,2 мин. (карта 5; поз. 16б);
<a id="p100155"></a>установить оправку в шпиндель - 1,45 мин. (карта 5; поз. 6б);
<a id="p100156"></a>повернуть стол на 90° 4 раза - 1,35 мин. (карта 5; поз. 20б);
<a id="p100157"></a>совместить 3 раза ось шпинделя и детали - 0,66 мин. (карта 5; поз. 46г);
<a id="p100158"></a>сменить резец 2 раза - 0,99 мин. (карта 5; поз. 2б);
<a id="p100159"></a>установить 2 раза сверло - 0,44 мин. (карта 5; поз. 5б);
<a id="p100160"></a>установить метчик - 0,44 мин. (карта 5; поз. 5б).


###### <a id="p100161"></a>1.8.1.5 Карта примера расчета нормы времени



<a id="p100192"></a>

<table>
<colgroup><col width="20%"><col width="15%"><col width="9%"><col width="11%"><col width="6%"><col width="7%"><col width="8%"><col width="9%"><col width="7%"><col width="8%"></colgroup>
<tr><td rowspan="2">Содержание работы</td><td rowspan="2">Инструмент режущий</td><td colspan="2">Размеры обработки</td><td rowspan="2">Глубина t, мм</td><td rowspan="2">Число проходов i</td><td rowspan="2">Неполное штучное время</td><td rowspan="2">Номер карты, позиции</td><td rowspan="2">Вспомогательное время</td><td rowspan="2">Номер карты, позиции</td></tr>
<tr><td>диаметр (длина)</td><td>расчетная длина l + h</td></tr>
<tr><td>1. Установить деталь, выверить и снять</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>14</td><td>3; 3ж</td></tr>
<tr><td>2. Установить фрезу на оправку</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>2,2</td><td>5; 16б</td></tr>
<tr><td>3. Установить оправку в шпиндель</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,45</td><td>5; 6б</td></tr>
<tr><td>4. Фрезеровать поверхность 2</td><td>Фреза торцовая с пластинками ВК8; диам. 200 мм</td><td>-</td><td>90 + 18</td><td>8</td><td>1</td><td>2,4</td><td>52; 12г</td><td>-</td><td>-</td></tr>
<tr><td>5. Повернуть стол на 90°</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,35</td><td>5; 20б</td></tr>
<tr><td>6. Фрезеровать поверхность 3</td><td>Фреза торцовая с пластинками ВК8; диам. 200 мм</td><td>-</td><td>75 + 13</td><td>8</td><td>1</td><td>2,1</td><td>52; 12в</td><td></td><td></td></tr>
<tr><td>7. Повернуть стол на 90°</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,35</td><td>5; 20б</td></tr>
<tr><td>8. Фрезеровать поверхность 4</td><td>Фреза торцовая с пластинками ВК8; диам. 200 мм</td><td>-</td><td>90 + 18</td><td>8</td><td>1</td><td>2,4</td><td>52; 12г</td><td></td><td></td></tr>
<tr><td>9. Фрезеровать поверхность 1 предварительно</td><td>Фреза торцовая с пластинками ВК8; диам. 200 мм</td><td></td><td>400 + 33</td><td>8</td><td>2</td><td>5 х 2</td><td>52; 12к</td><td></td><td></td></tr>
<tr><td>10. Фрезеровать поверхность 1 окончательно</td><td>Фреза торцовая с пластинками ВК8; диам. 200 мм</td><td>400 х 260</td><td>400 + 200</td><td>3</td><td>2</td><td>5,5 х 2</td><td>53; 9д</td><td>-</td><td>-</td></tr>
<tr><td>11. Установить консольную оправку</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,45</td><td>5; 6б</td></tr>
<tr><td>12. Совместить ось шпинделя и детали</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,66</td><td>5; 46г</td></tr>
<tr><td>13. Расточить поверхность 6 предварительно</td><td>Резец расточной ВК8</td><td>диам. 120 мм</td><td>30 + 11</td><td>8</td><td>1</td><td>1,8</td><td>7; 14б</td><td>-</td><td>-</td></tr>
<tr><td>14. Сменить резец</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,99</td><td>5; 2б</td></tr>
<tr><td>15. Расточить поверхность 6 окончательно</td><td>Резец расточной ВК6</td><td>диам. 120 мм</td><td>30 + 2</td><td>1</td><td>1</td><td>4,55</td><td>10; 6б</td><td>-</td><td>-</td></tr>
<tr><td>16. Повернуть стол на 90°</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,35</td><td>5; 20б</td></tr>
<tr><td>17. Совместить ось шпинделя и детали</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,66</td><td>5; 46г</td></tr>
<tr><td>18. Установить резец</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,99</td><td>5; 2б</td></tr>
<tr><td>19. Расточить отверстие пов. 5 предварительно</td><td>Резец расточной ВК8</td><td>диам. 50 мм</td><td>80 + 80 + 11</td><td>5</td><td>1</td><td>2,55</td><td>7; 5ж</td><td>-</td><td>-</td></tr>
<tr><td>20. Сменить резец</td><td></td><td></td><td></td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,99</td><td>5; 2б</td></tr>
<tr><td>21. Расточить отверстие пов. 5 окончательно</td><td>Резец расточной ВК6</td><td>диам. 50 мм</td><td>80 + 80 + 2</td><td>1</td><td>1</td><td>5,5</td><td>10; 3ж</td><td>-</td><td>-</td></tr>
<tr><td>22. Повернуть стол на 90°</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,35</td><td>5; 20б</td></tr>
<tr><td>23. Совместить ось шпинделя и детали</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,66</td><td>5; 46г</td></tr>
<tr><td>24. Установить сверло</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,44</td><td>5; 5б</td></tr>
<tr><td>25. Сверлить отв. диам. 14,3 мм</td><td>Сверло спиральное диам. 14,3 мм Р6М5</td><td>диам. 14,3 мм</td><td>30 + 6</td><td>8</td><td>1</td><td>0,63</td><td>82; 4г</td><td>-</td><td>-</td></tr>
<tr><td>26. Установить сверло</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,44</td><td>5; 5б</td></tr>
<tr><td>27. Снять фаску</td><td>Сверло</td><td>диам.</td><td>-</td><td>1,5</td><td>1</td><td>0,35</td><td>92</td><td>-</td><td>-</td></tr>
<tr><td>18 х 1,5</td><td>спиральное диам. 20 мм Р6М5</td><td>20 мм</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td></tr>
<tr><td>28. Установить метчик</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,44</td><td>5; 5б</td></tr>
<tr><td>29. Нарезать резьбу М16 х 1,5</td><td>Метчик М16 х 1,5 Р6М5</td><td>М16</td><td>30 + 10</td><td>1,5</td><td>1</td><td>1,85</td><td>92; 5д</td><td>-</td><td>-</td></tr>
<tr><td>Т = (t + t ш в.у</td><td>+ t н.ш н.ш 1 2</td><td>+ ... + t</td><td>+ t н.ш в.доп n</td><td>) х К</td><td>Тш</td><td>=</td><td></td><td></td><td></td></tr>
</table>


    = (14 + 2,4 + 2,1 + 2,4 + 10 + 11 + 1,8 + 4,55 + 2,55 + 5,5 + 0,63 +

    + 0,35 + 1,85 + 16,77) х 1 = 75,9 мин.

               t
                п.з          16
<a id="p100193"></a>    Н   = Т  + ---- = 75,9 + -- = 75,9 + 3,2 = 79,1 мин.
     вр    ш    q            5


##### <a id="p100194"></a>1.8.2 РАСЧЕТ НОРМЫ ВРЕМЕНИ. ГОРИЗОНТАЛЬНО-РАСТОЧНЫЕ СТАНКИ,

<div align="center">

**СРЕДНЕСЕРИЙНОЕ ПРОИЗВОДСТВО**

<a id="p100195"></a>Рис. 1.2.<br>
(не приводится)

</div>



###### <a id="p100196"></a>1.8.2.1 Исходные данные


    1. <a id="p100197"></a>Станок - горизонтально-расточной, 2620В, диаметр выдвижного шпинделя
- 90 мм, N  = 11 кВт.
          д
2. <a id="p100198"></a>Деталь - корпус.
3. <a id="p100199"></a>Обрабатываемый материал - чугун серый СЧ15-32; НВ = 1,86 ГПа.
4. <a id="p100200"></a>Масса заготовки - 200 кг.
5. <a id="p100201"></a>Масса детали - 190 кг.
6. <a id="p100202"></a>Операция - расточная.
7. <a id="p100203"></a>Заготовка - отливка.
8. <a id="p100204"></a>Приспособление - болты, планки.
9. <a id="p100205"></a>Режущий инструмент - фреза торцовая диам. 200, пластинки из твердого сплава ВК8.
10. <a id="p100206"></a>Число деталей в партии - 30 шт.


###### <a id="p100207"></a>1.8.2.2 Определение подготовительно-заключительного времени


<a id="p100208"></a>Подготовительно-заключительное время определяется по карте 93.
<a id="p100209"></a>По технологическому процессу работа выполняется за 6 переходов при диаметре шпинделя 110 мм. Подготовительно-заключительное время равно 19 мин. (поз. 1б).
<a id="p100210"></a>К подготовительно-заключительному времени добавляется время из той же карты 10 мин. на получение инструмента и приспособлений и сдачу их после окончания обработки партии деталей (поз. 4).
<a id="p100211"></a>    Итого t    = 19 + 10 = 29 мин.
           п.з
<a id="p100212"></a>Данные расчета сведены в карту (см. [ниже](#p100259)).
<a id="p100213"></a>Обработка производится инструментом из стали ВК8 с режимами, приведенными в технологической карте.


###### <a id="p100214"></a>1.8.2.3 Вспомогательное время на установку и снятие детали


<a id="p100215"></a>    Время  на установку и снятие заготовки на столе при креплении болтами и
планками массой 200 кг t    = 7,8 мин. (карта 94; поз. 2л).
                        в.у
<a id="p100216"></a>Определение основного (технологического) времени приводится для каждого перехода в отдельности согласно наименованию переходов, приведенных в карте расчета нормы штучного времени.


###### <a id="p100217"></a>1.8.2.4 Определение основного времени


<a id="p100218"></a>Основное время определяется по формуле:

                          t      (l + l )
                           о 100       t
<a id="p100219"></a>                     t  = --------------- х i (мин.),
                      о         100

    где:
<a id="p100220"></a>    l - длина обрабатываемой поверхности (определяется по чертежу), мм;
<a id="p100221"></a>    l  - величина врезания и перебега инструмента, мм;
     t
<a id="p100222"></a>    i - число переходов;
<a id="p100223"></a>    t      - основное время на обработку 100 мм длины, мин.
     о 100
<a id="p100224"></a>    Для каждой обрабатываемой поверхности в соответствии с условиями работы
величина врезания и перебега инструмента указана в картах основного времени
и для данного примера равна:
<a id="p100225"></a>    Для поверхности 1 l  = 7 мм;
                       t
<a id="p100226"></a>    -"-     -"-     2 l  = 2 мм;
                       t
<a id="p100227"></a>    -"-     -"-     3 l  = 7 мм;
                       t
<a id="p100228"></a>    -"-     -"-     4 l  = 2 мм;
                       t
<a id="p100229"></a>    -"-     -"-     5 l  = 2 мм;
                       t
<a id="p100230"></a>    -"-     -"-     6 l  = 2 мм.
                       t
<a id="p100231"></a>    Тогда основное время обработки составит для перехода 1.

          t     (l + l )
           о 100      t        3,7(80 + 7)
<a id="p100232"></a>    t   = -------------- х i = ----------- х 1 = 3,22 мин. (карта 98;  поз.
     о         100                 100
      1
30в);

<a id="p100233"></a>    для перехода 2

          t     (l + l )
           о 100      t        4,73(80 + 2)
<a id="p100234"></a>    t   = -------------- х i = ------------ х 1 =  3,87  мин.  (карта  101;
     о         100                 100
      2
поз. 10в);

<a id="p100235"></a>    для перехода 3

          t     (l + l )
           о 100      t        1,5(120 + 7)
<a id="p100236"></a>    t   = -------------- х i = ------------ х 1 = 1,9 мин. (карта 98;  поз.
     о         100                 100
      3
11в);

          t     (l + l )
           о 100      t        1,51(120 + 2)
<a id="p100237"></a>    t   = -------------- х i = ------------- х 1 = 1,84  мин.  (карта  101;
     о         100                  100
      4
поз. 5в);

          t     (l + l )
           о 100      t        2,7(8 + 2)
<a id="p100238"></a>    t   = -------------- х i = ---------- х 1 = 2,7 мин.  (карта 108;  поз.
     о         100                100
      5
3б);

          t     (l + l )
           о 100      t        2,7(8 + 2)
<a id="p100239"></a>    t   = -------------- х i = ---------- х 1 = 2,7 мин. (карта  108;  поз.
     о         100                100
      6
3б).

<a id="p100240"></a>    Основное время на операцию равно:

<a id="p100241"></a>    t  = t   + t   + t   + t   + t   + t   = 16,23 мин.
     о    о     о     о     о     о     о
           1     2     3     4     5     6


###### <a id="p100242"></a>1.8.2.5 Вспомогательное время, связанное с переходом, берется из карты

96  с  учетом времени на дополнительные приемы, изменение частоты вращения,
подачи и т.п. Вспомогательное время равно:
<a id="p100243"></a>    переход 1 t   = 0,55 мин.;
               вп
<a id="p100244"></a>      -"-   2 t   = 0,20 мин. + 0,7 + 0,1 + 0,08;
               вп
<a id="p100245"></a>      -"-   3 t   = 0,55 мин. + 2,0 + 0,7 + 0,1 + 0,08;
               вп
<a id="p100246"></a>      -"-   4 t   = 0,20 мин. + 0,7 + 0,1 + 0,08;
               вп
<a id="p100247"></a>      -"-   5 t   = 0,17 мин. + 1,3 + 0,1 + 0,08;
               вп
<a id="p100248"></a>      -"-   6 t   = 0,17 мин. + 0,7,
               вп
<a id="p100249"></a>где:
<a id="p100250"></a>0,7 - установка и снятие инструмента;
<a id="p100251"></a>0,1 - включение и выключение подачи;
<a id="p100252"></a>0,08 - включение и выключение вращения шпинделя;
<a id="p100253"></a>2,0 - поворот стола на 180°;
<a id="p100254"></a>1,3 - смена консольной борштанги.


###### <a id="p100255"></a>1.8.2.6 Вспомогательное время на контрольные измерения


<a id="p100256"></a>Вспомогательное время на контрольные измерения определяется только для 2 переходов (2-го и 4-го) и равно 1,08 мин. (карта 97; поз. 16а и 14б).
<a id="p100257"></a>Вспомогательное время на операцию составит:

<a id="p100258"></a> t  = t    + t   + t      + t      = 7,8 + 1,84 + 6,82 + 1,08 = 17,54 мин.
  в    в.у    вп    в.доп    в.изм

<div align="center">

<a id="p100259"></a>Карта расчета нормы времени. Среднесерийное производство

<a id="p100260"></a>Рис. 1.3.<br>
(не приводится)

</div>



<table>
<colgroup><col width="2%"><col width="12%"><col width="3%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="3%"><col width="4%"><col width="3%"><col width="5%"><col width="4%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td rowspan="3">N переходов</td><td rowspan="3">Содержание переходов</td><td rowspan="3">Приспособление</td><td colspan="2">Инструмент</td><td colspan="3">Размеры обработки</td><td rowspan="3">Число проходов i</td><td colspan="7">Режимы обработки</td><td rowspan="3">Вспомогательное время на установку и снятие детали t , в.у мин.</td><td rowspan="3">Вспомогательное время, связанное с переходом t , в.п мин.</td><td rowspan="3">Вспомогательное время дополнительное, t , в.доп. мин.</td><td rowspan="3">Вспомогательное время на контрольные измерения, t , в.изм. мин.</td><td rowspan="3">Номер карты, позиции</td></tr>
<tr><td rowspan="2">режущий</td><td rowspan="2">измерительный</td><td rowspan="2">длина l, мм</td><td rowspan="2">врезание и перебег t , мм 1</td><td rowspan="2">расчетная длина l , мм р</td><td rowspan="2">l, мм</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">n, об./ мин.</td><td colspan="2">Основное время t , мин. о</td><td rowspan="2">Номер карты, позиции</td></tr>
<tr><td>на 100 мм длины (10 мм)</td><td>при расчетной длине</td></tr>
<tr><td>1</td><td>Установить деталь, выверить и снять</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td></td><td>-</td><td>-</td><td>7,8</td><td>-</td><td>-</td><td>-</td><td>94; 2л</td></tr>
<tr><td>2</td><td>Совмещение оси отверстия диам. 250 с осью шпинделя</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>-</td><td>-</td><td>2,0</td><td>-</td><td>96; 16г</td></tr>
<tr><td>3</td><td>Расточить предварительно поверхность 1</td><td></td><td></td><td></td><td>80</td><td>7</td><td>87</td><td></td><td>8</td><td>0,45</td><td>56</td><td>60</td><td>3,7</td><td>3,22</td><td>98; 30в</td><td>-</td><td>0,55</td><td>-</td><td>-</td><td>96; 23б</td></tr>
<tr><td>4</td><td>Смена резца</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>-</td><td>-</td><td>0,7</td><td>-</td><td>96; 55б</td></tr>
<tr><td>5</td><td>Расточить окончательно поверхность 1</td><td></td><td></td><td></td><td>80</td><td>2</td><td>82</td><td></td><td>1</td><td>0,22</td><td>90</td><td>96</td><td>4,73</td><td>3,87</td><td>101; 10в</td><td>-</td><td>0,20</td><td>0,1; 0,08</td><td>0,7</td><td>96; 27б; 43б; 44б; 97; 16а</td></tr>
<tr><td>6</td><td>Повернуть стол на 180°</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>-</td><td>-</td><td>2,0</td><td>-</td><td>96; 20д</td></tr>
<tr><td>7</td><td>Установить резец</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>-</td><td>-</td><td>0,7</td><td>-</td><td>96; 55б</td></tr>
<tr><td>8</td><td>Расточить предварительно поверхность 2</td><td></td><td></td><td></td><td>120</td><td>7</td><td>127</td><td></td><td>8</td><td>0,35</td><td>57</td><td>190</td><td>1,5</td><td>1,90</td><td>98; 11в</td><td>-</td><td>0,55</td><td>0,1; 0,08</td><td>-</td><td>96; 23б; 43б; 44б</td></tr>
<tr><td>9</td><td>Расточить окончательно поверхность 2</td><td></td><td></td><td>калибр пробка неполная</td><td>120</td><td>2</td><td>122</td><td>1</td><td>1</td><td>0,22</td><td>90</td><td>300</td><td>1,51</td><td>1,84</td><td>101; 5в</td><td>-</td><td>0,20</td><td>0,7; 0,1; 0,08</td><td>0,38</td><td>96; 27б; 55б; 43б; 44б; 97; 14б</td></tr>
<tr><td>10</td><td>Смена борштанги для расточки пластин</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td></tr>
<tr><td>11</td><td>Подрезать внутренний торец бобышки</td><td></td><td></td><td></td><td></td><td>2</td><td></td><td>1</td><td></td><td>3,70</td><td>28</td><td></td><td>2,7</td><td>2,70</td><td>108; 3б</td><td>-</td><td>0,17</td><td>1,3; 0,1; 0,08</td><td></td><td>96; 28б; 8б; 48б; 96; 43б; 44б</td></tr>
<tr><td>12</td><td>Переустановить подрезную пластину</td><td></td><td>подрезн. пластина</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td></tr>
<tr><td>13</td><td>Подрезать наружный торец бобышки в размер</td><td></td><td></td><td></td><td>8</td><td>2</td><td>10</td><td>1</td><td></td><td>3,70</td><td>28</td><td></td><td>2,7</td><td>2,70</td><td>108; 3б</td><td>-</td><td>0,17</td><td>0,7</td><td>-</td><td>96; 28б; 96; 55б</td></tr>
<tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Итого</td><td></td><td></td><td>16,23</td><td>-</td><td>7,8</td><td>1,84</td><td>6,82</td><td>1,08</td><td>-</td></tr>
<tr><td></td><td></td><td></td><td>а обс</td><td>+ а отд</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td></tr>
</table>

<a id="p100276"></a>    Т  = (t  + t  х К   ) х (1 + -----------) = (16,23 + 17,54 х 0,66) х
     ш     о    в    t.в             100

       4,5 + 4,00
х (1 + ----------) = 30,16 мин.
          100

<a id="p100277"></a>По карте 1 определяется поправочный коэффициент на вспомогательное время в зависимости от суммарной продолжительности обработки партии деталей по трудоемкости.
<a id="p100278"></a>При трудоемкости обработки партии деталей в 2 - 3 смены этот коэффициент равен 0,66.
<a id="p100279"></a>С учетом поправочного коэффициента вспомогательное время на операцию составит:

<a id="p100280"></a>    t  х К    = 17,54 х 0,66 = 11,57 мин.
     в    t.в


###### <a id="p100281"></a>1.8.2.7 Определение времени на обслуживание рабочего места,

<div align="center">

отдых и личные потребности

</div>


<a id="p100282"></a>Время на обслуживание рабочего места определяется по карте 93 (поз. 9б).
<a id="p100283"></a>Для горизонтально-расточных станков с диаметром шпинделя 110 мм оно составляет 4,5% оперативного времени.
<a id="p100284"></a>Время на отдых и личные потребности определяется по карте 93. Оно составляет 4% оперативного времени.

<a id="p100285"></a>    t  = 7,8 + 1,84 + 6,82 + 1,08 = 17,54 мин.
     в


###### <a id="p100286"></a>1.8.2.8 Определение нормы штучного времени


<a id="p100287"></a>Норма штучного времени определяется по формуле:

                                 а    + а
                                  обс    отд
<a id="p100288"></a>    Т  = (t  + t  х К   ) х (1 + -----------) = (16,23 + 17,54 х 0,66) х
     ш     о    в    t.в             100

       4,5 + 4
х (1 + -------) = 30,16 мин.
         100


###### <a id="p100289"></a>1.8.2.9 Определение нормы времени


         t
          н.в           19 + 10
<a id="p100290"></a>    Т  = ---- = 30,16 + ------- = 30,16 + 0,96 = 31,12 мин.
     ш    q               30


### 2. <a id="p100291"></a>ХАРАКТЕРИСТИКА ПРИМЕНЯЕМОГО ОБОРУДОВАНИЯ


<a id="p100292"></a>2.1. Нормативы времени рассчитаны для применения при нормировании работ, выполняемых на оборудовании широко распространенных на предприятиях конструкций отечественного производства.
<a id="p100293"></a>К числу распространенных конструкций относятся станки: горизонтально-расточные 2622В; 2636; 2Е6П6Р. Технической и технологической характеристикой этих моделей станков является то, что они имеют полный набор подач, частот вращения и достаточную мощность.


| Тип станка | Модель | Основные размеры, диам. шпинделя В х L стола, мм | Мощность, кВт | Частота вращения, об./мин. |
| --- | --- | --- | --- | --- |
| Горизонтальнорасточной | 2622В 2636 2Е6П6Р | 110 х 1120 х 1250 125 х 1600 х 1800 диам. 160 | 11 19 18 | 12,5 - 1250 5 - 800 7,5 - 950 |


<a id="p100298"></a>Приведенные в сборнике нормативы времени на выполнение технологических операций рассчитаны на характерную для единичного, мелкосерийного и среднесерийного производства организацию труда и рабочих мест.
<a id="p100299"></a>Уровень режимов резания был установлен с учетом использования режущих свойств инструмента и для обработки на современном, наиболее распространенном оборудовании.
<a id="p100300"></a>При этом учитывались также возможности инструмента по его прочности и мощность станка.


### 3. <a id="p100301"></a>ОРГАНИЗАЦИЯ ТРУДА


<a id="p100302"></a>3.1. На участке станочных работ рабочее место должно быть оснащено всем необходимым в соответствии с требованиями производственного процесса и условиями выполнения работы с соблюдением правил санитарной гигиены и техники безопасности.
<a id="p100303"></a>Расположение оборудования на рабочем месте, инвентаря, производственной мебели, тары, стеллажей для заготовок и готовой продукции планируется с таким расчетом, чтобы не создавалось стесненных условий работы, лишних затрат времени на хождения и поиски.
<a id="p100304"></a>При рациональной организации рабочих мест рекомендуется придерживаться существующих общих положений (см. Типовые проекты организации труда на рабочих местах станочников. Оргстанкинпром).
<a id="p100305"></a>Освещение рабочего места должно быть достаточным и правильным. Требуемая освещенность определяется характером выполняемой работы и действующими санитарными нормами. При местном освещении свет не должен слепить глаза, тень не должна падать на обрабатываемую деталь.
<a id="p100306"></a>На рабочем месте имеется инструкционно-эксплуатационная карта для выбора режимов резания.
<a id="p100307"></a>Инструменты и приспособления располагаются на рабочем месте в определенном, удобном для пользования, порядке.
<a id="p100308"></a>Участок обработки тяжелых деталей оснащен подъемно-транспортными устройствами. Ниже приведен пример типовой планировки рабочего места станочника-расточника на горизонтально-расточном станке.


#### <a id="p100309"></a>3.2 РАБОЧЕЕ МЕСТО РАСТОЧНИКА

<div align="center">

**НА ГОРИЗОНТАЛЬНО-РАСТОЧНОМ СТАНКЕ**

<a id="p100310"></a>Рис. 3.1.<br>
(не приводится)

</div>



#### <a id="p100311"></a>3.3 ОРГОСНАСТКА РАБОЧИХ МЕСТ


<a id="p100312"></a>Оснащение рабочих мест станочников оргоснасткой (инструментальными тумбочками, приемными столами и т.п.) должно проводиться на основе типовых конструкций. Специальная оргоснастка проектируется в исключительных случаях, если по тем или иным причинам не подходит типовая.
<a id="p100313"></a>Ниже в качестве примера приведены отдельные конструкции типовой оргоснастки.
<a id="p100314"></a>Собирается из унифицированных элементов. Предназначена для оснащения рабочих мест станочников.

<div align="center">

<a id="p100315"></a>Рис. 3.2.<br>
(не приводится)

</div>


<a id="p100316"></a>Габариты, мм 900 х 500 х 1000.
<a id="p100317"></a>Масса, кг 80.
<a id="p100318"></a>Изготовитель - Московский завод "Станкоагрегат".
<a id="p100319"></a>Чертеж N С3746.05.
<a id="p100320"></a>Тумбочка предназначена для хранения необходимого инструмента на рабочих местах станочников, документации и средств по уходу за оборудованием. Каждая отдельная тумбочка закрывается дверцей и закрепляется за одним рабочим. В каждом отделении имеются ящики для инструмента и полки для хранения документации, небольших принадлежностей и приспособлений, масленок, обтирочных материалов и др. Съемный планшет для крепления чертежей, изготовляемый из декоративного древесно-волокнистого пластика, закрепляется в кронштейнах.

<div align="center">

<a id="p100321"></a>Рис. 3.3.<br>
(не приводится)

</div>


<a id="p100322"></a>Предназначен для оснащения рабочих мест станочников.
<a id="p100323"></a>    Грузоподъемность, т    2
<a id="p100324"></a>    Габариты, мм           1150 х 750 х 600
<a id="p100325"></a>На верхней полке стола размещается тара с обрабатываемыми деталями или сами детали. При необходимости на нижней полке могут храниться приспособления и принадлежности.
<a id="p100326"></a>На отдельных рабочих местах стол может быть использован для раскладки на нем непосредственно используемого в работе инструмента.


### 4. <a id="p100327"></a>НОРМАТИВНАЯ ЧАСТЬ



<table>
<colgroup><col width="11%"><col width="18%"><col width="9%"><col width="5%"><col width="4%"><col width="9%"><col width="4%"><col width="3%"><col width="3%"><col width="9%"><col width="3%"><col width="5%"><col width="5%"><col width="3%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Поправочные коэффициенты на штучное время в зависимости от размера партии обрабатываемых деталей</td><td colspan="8">Все типы станков</td></tr>
<tr><td colspan="8">Карта 1</td></tr>
<tr><td colspan="15">I. Поправочные коэффициенты на штучное время в зависимости от размера партии обрабатываемых деталей в единичном и мелкосерийном производстве</td></tr>
<tr><td rowspan="3">N позиции</td><td>Штучное время, мин.,</td><td colspan="13">Число деталей в партии, шт., до</td></tr>
<tr><td rowspan="2">до</td><td>3</td><td colspan="2">6</td><td>10</td><td colspan="3">15</td><td>20</td><td colspan="2">30</td><td colspan="2">40</td><td>&gt; 40</td></tr>
<tr><td colspan="10">Коэффициент на штучное время К Тш</td><td colspan="2"></td><td></td></tr>
<tr><td rowspan="3">1</td><td rowspan="3">3</td><td rowspan="3">1,40</td><td colspan="2" rowspan="3">1,20</td><td rowspan="3">1,10</td><td colspan="3" rowspan="3">1,05</td><td></td><td colspan="2" rowspan="3">0,95</td><td colspan="2" rowspan="3">0,90</td><td rowspan="3">0,85</td></tr>
<tr><td>1,00</td></tr>
<tr><td></td></tr>
<tr><td rowspan="3">2</td><td rowspan="3">15</td><td rowspan="3">1,20</td><td colspan="2" rowspan="3">1,10</td><td rowspan="3">1,05</td><td colspan="3"></td><td rowspan="3">0,95</td><td colspan="2" rowspan="3">0,90</td><td colspan="2" rowspan="3">0,85</td><td rowspan="3">-</td></tr>
<tr><td colspan="3">1,00</td></tr>
<tr><td colspan="3"></td></tr>
<tr><td rowspan="3">3</td><td rowspan="3">60</td><td rowspan="3">1,10</td><td colspan="2" rowspan="3">1,05</td><td></td><td colspan="3" rowspan="3">0,95</td><td rowspan="3">0,90</td><td colspan="2" rowspan="3">0,85</td><td colspan="2" rowspan="3">-</td><td rowspan="3">-</td></tr>
<tr><td>1,00</td></tr>
<tr><td></td></tr>
<tr><td rowspan="3">4</td><td rowspan="3">300</td><td rowspan="3">1,05</td><td colspan="2"></td><td rowspan="3">0,95</td><td colspan="3" rowspan="3">0,90</td><td rowspan="3">0,85</td><td colspan="2" rowspan="3">-</td><td colspan="2" rowspan="3">-</td><td rowspan="3">-</td></tr>
<tr><td colspan="2">1,00</td></tr>
<tr><td colspan="2"></td></tr>
<tr><td rowspan="3">5</td><td rowspan="3">&gt; 300</td><td></td><td colspan="2" rowspan="3">0,95</td><td rowspan="3">0,90</td><td colspan="3" rowspan="3">0,85</td><td rowspan="3">-</td><td colspan="2" rowspan="3">-</td><td colspan="2" rowspan="3">-</td><td rowspan="3">-</td></tr>
<tr><td>1,00</td></tr>
<tr><td></td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td colspan="3">г</td><td>д</td><td colspan="2">е</td><td colspan="2">ж</td><td>з</td></tr>
<tr><td colspan="15">II. Поправочные коэффициенты на вспомогательное время в зависимости от характера серийности работ в среднесерийном производстве</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="3" rowspan="3">Наименование оборудования</td><td colspan="11">Суммарная продолжительность обработки партии деталей по трудоемкости операции, рабочих смен, до</td></tr>
<tr><td colspan="5">0,25 0,50</td><td colspan="2">1,00</td><td colspan="2">2,00</td><td colspan="2">4,00</td></tr>
<tr><td colspan="11">Коэффициент на вспомогательное время К t.в</td></tr>
<tr><td rowspan="3">1</td><td colspan="3" rowspan="3">Горизонтально-расточные станки</td><td colspan="5"></td><td colspan="2" rowspan="3">0,87</td><td colspan="2" rowspan="3">0,76</td><td colspan="2" rowspan="3">0,66</td></tr>
<tr><td colspan="2">1,15</td><td colspan="2">1,00</td><td></td></tr>
</table>


<a id="p100340"></a>    Примечания:  1. Поправочные коэффициенты на штучное время в единичном и
мелкосерийном  производстве  (К  )  и  на  вспомогательное  время  (К   ) в
                               Тш                                    t.в
среднесерийном  производстве  следует  применять  при расчете норм штучного
времени  в  процессе подготовки производства с учетом серийности работ. Тип
производства  характеризуется  коэффициентом  закрепления  операций (К   ).
                                                                      з.о
Серийность   работы  внутри  типа  производства  как  фактор  специализации
производства  измеряется  в  нормативах продолжительности времени обработки
партии одинаковых деталей на станке.
2. <a id="p100341"></a>Продолжительность работы станка по обработке партии деталей рассчитывается с учетом трудоемкости ориентации числа деталей в партии и устанавливается по согласованию с плановыми органами завода как средняя величина для всех запусков изделий в производстве в течение года.


#### <a id="p100342"></a>4.1. НОРМАТИВЫ ВРЕМЕНИ



<table>
<colgroup><col width="11%"><col width="20%"><col width="15%"><col width="12%"><col width="3%"><col width="4%"><col width="8%"><col width="7%"><col width="3%"><col width="4%"><col width="8%"><col width="7%"></colgroup>
<tr><td colspan="5" rowspan="2">Подготовительно-заключительное время Единичное и мелкосерийное производство</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="4">Карта 2</td><td colspan="3">Лист 1</td></tr>
<tr><td colspan="12">I. Подготовительно-заключительное время</td></tr>
<tr><td rowspan="4">N позиции</td><td rowspan="4">Способ установки детали</td><td rowspan="4">Сложность подготовки к работе</td><td>Число инструментов в</td><td colspan="8">Группа станков: диаметр шпинделя, мм, до</td></tr>
<tr><td rowspan="3">наладке</td><td colspan="2">65</td><td>110</td><td>160</td><td colspan="2">65</td><td>110</td><td>160</td></tr>
<tr><td colspan="4">С заменой установочных приспособлений</td><td colspan="4">Без замены установочных приспособлений</td></tr>
<tr><td colspan="8">Время, мин.</td></tr>
<tr><td>1</td><td>На столе (плите) с</td><td rowspan="2">Простая</td><td>1 - 3</td><td colspan="2">15</td><td>17</td><td>20</td><td colspan="2">10</td><td>12</td><td>14</td></tr>
<tr><td>2</td><td>креплением болтами и</td><td>4 - 6</td><td colspan="2">18</td><td>20</td><td>23</td><td colspan="2">12</td><td>14</td><td>17</td></tr>
<tr><td>3</td><td rowspan="6">планками</td><td rowspan="3">Средней сложности</td><td>2 - 4</td><td colspan="2">19</td><td>22</td><td>25</td><td colspan="2">14</td><td>16</td><td>18</td></tr>
<tr><td>4</td><td>5 - 7</td><td colspan="2">22</td><td>25</td><td>28</td><td colspan="2">15</td><td>18</td><td>21</td></tr>
<tr><td>5</td><td>8 - 10</td><td colspan="2">25</td><td>28</td><td>31</td><td colspan="2">18</td><td>20</td><td>24</td></tr>
<tr><td>6</td><td rowspan="3">Сложная</td><td>3 - 5</td><td colspan="2">26</td><td>30</td><td>33</td><td colspan="2">19</td><td>22</td><td>25</td></tr>
<tr><td>7</td><td>6 - 8</td><td colspan="2">29</td><td>33</td><td>36</td><td colspan="2">22</td><td>25</td><td>28</td></tr>
<tr><td>8</td><td>9 - 12</td><td colspan="2">32</td><td>36</td><td>40</td><td colspan="2">25</td><td>29</td><td>32</td></tr>
<tr><td>9</td><td rowspan="8">На угольнике или в приспособлении</td><td rowspan="2">Простая</td><td>1 - 3</td><td colspan="2">22</td><td>25</td><td>28</td><td colspan="2">12</td><td>14</td><td>16</td></tr>
<tr><td>10</td><td>4 - 6</td><td colspan="2">25</td><td>28</td><td>31</td><td colspan="2">15</td><td>16</td><td>18</td></tr>
<tr><td>11</td><td rowspan="3">Средней сложности</td><td>2 - 4</td><td colspan="2">26</td><td>30</td><td>33</td><td colspan="2">16</td><td>17</td><td>20</td></tr>
<tr><td>12</td><td>5 - 7</td><td colspan="2">29</td><td>33</td><td>36</td><td colspan="2">19</td><td>20</td><td>23</td></tr>
<tr><td>13</td><td>8 - 10</td><td colspan="2">32</td><td>36</td><td>39</td><td colspan="2">21</td><td>23</td><td>26</td></tr>
<tr><td>14</td><td rowspan="3">Сложная</td><td>3 - 5</td><td colspan="2">33</td><td>38</td><td>42</td><td colspan="2">22</td><td>24</td><td>28</td></tr>
<tr><td>15</td><td>6 - 8</td><td colspan="2">36</td><td>41</td><td>45</td><td colspan="2">25</td><td>27</td><td>31</td></tr>
<tr><td>16</td><td>9 - 12</td><td colspan="2">40</td><td>45</td><td>50</td><td colspan="2">28</td><td>31</td><td>35</td></tr>
<tr><td></td><td></td><td>Индекс</td><td></td><td colspan="2">а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="11%"><col width="9%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="8" rowspan="2">Подготовительно-заключительное время Единичное и мелкосерийное производство</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="6">Карта 2 Лист 2</td></tr>
<tr><td colspan="14">II. Время на дополнительные элементы подготовительно-заключительной работы, не включенные в комплексы</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="7" rowspan="3">Наименование работы</td><td colspan="6">Группа станков: диаметр шпинделя, мм, до</td></tr>
<tr><td colspan="3">6,5</td><td>110</td><td colspan="2">160</td></tr>
<tr><td colspan="6">Время, мин.</td></tr>
<tr><td>1</td><td>Установить</td><td colspan="2" rowspan="2">летучий суппорт</td><td colspan="4">вручную</td><td colspan="3">5,5</td><td>6,5</td><td colspan="2">8,0</td></tr>
<tr><td>2</td><td rowspan="16">и снять</td><td colspan="4">краном</td><td colspan="3">-</td><td>-</td><td colspan="2">18,0</td></tr>
<tr><td>3</td><td colspan="2">домкрат или</td><td colspan="4">вручную</td><td colspan="3">1,0</td><td colspan="3">1,5</td></tr>
<tr><td>4</td><td colspan="2">призму</td><td colspan="4">краном</td><td colspan="3">3,0</td><td colspan="3">3,5</td></tr>
<tr><td>5</td><td colspan="2" rowspan="3">угольник с выверкой</td><td colspan="4">Высота 500</td><td colspan="6">10</td></tr>
<tr><td>6</td><td colspan="4">ка, мм, 1000</td><td colspan="6">13</td></tr>
<tr><td>7</td><td colspan="4">1500</td><td colspan="6">15</td></tr>
<tr><td>8</td><td colspan="2">дополнительный</td><td colspan="4">без выверки</td><td colspan="3">6,0</td><td>7,0</td><td colspan="2">8,0</td></tr>
<tr><td>9</td><td colspan="2">стол</td><td colspan="4">с выверкой</td><td colspan="3">9,0</td><td>11,0</td><td colspan="2">12,0</td></tr>
<tr><td>10</td><td colspan="2" rowspan="2">подставку</td><td colspan="4">вручную</td><td colspan="3">1,5</td><td>1,8</td><td colspan="2">2,2</td></tr>
<tr><td>11</td><td colspan="4">краном</td><td colspan="3">2,5</td><td>3,0</td><td colspan="2">3,5</td></tr>
<tr><td>12</td><td colspan="6">заднюю стойку с выверкой</td><td colspan="3">-</td><td>-</td><td colspan="2">9,0</td></tr>
<tr><td>13</td><td colspan="3">накладной кондуктор при массе, кг, до</td><td>3</td><td>5</td><td>10</td><td>15</td><td>20</td><td>30</td><td>50</td><td>100</td><td>200</td></tr>
<tr><td>14</td><td rowspan="4">способ крепления кондуктора</td><td colspan="2">без крепления</td><td>0,20</td><td>0,24</td><td>0,32</td><td>0,39</td><td>0,45</td><td>1,55</td><td>1,70</td><td>1,95</td><td>2,30</td></tr>
<tr><td>15</td><td colspan="2">фиксатором по отверстию</td><td>0,23</td><td>0,27</td><td>0,36</td><td>0,44</td><td>0,50</td><td>1,70</td><td>1,85</td><td>2,15</td><td>2,60</td></tr>
<tr><td>16</td><td colspan="2">винтом</td><td>0,25</td><td>0,30</td><td>0,40</td><td>0,50</td><td>0,56</td><td>1,80</td><td>1,95</td><td>2,25</td><td>2,45</td></tr>
<tr><td>17</td><td colspan="2">болтами и планками</td><td>0,45</td><td>0,52</td><td>0,64</td><td>0,80</td><td>0,95</td><td>2,00</td><td>2,30</td><td>2,70</td><td>3,20</td></tr>
<tr><td></td><td></td><td></td><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="14%"><col width="14%"><col width="8%"><col width="6%"><col width="7%"><col width="6%"><col width="3%"><col width="2%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="8" rowspan="2">Вспомогательное время на установку и снятие детали Единичное и мелкосерийное производство</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="7">Карта 3 Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Способ установки и</td><td rowspan="3">Характер выверки</td><td>Точность</td><td colspan="11">Масса детали, кг, до</td></tr>
<tr><td rowspan="2">крепление детали</td><td>выверки на</td><td>10</td><td>20</td><td>30</td><td colspan="2">50</td><td>100</td><td>200</td><td>400</td><td>800</td><td>1500</td><td>3000</td></tr>
<tr><td>1 пог. м, мм, до</td><td colspan="11">Время, мин.</td></tr>
<tr><td>1</td><td>На столе (плите) с</td><td>Без выверки</td><td>-</td><td>1,45</td><td>1,75</td><td>4,6</td><td colspan="2">5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,0</td><td>12,5</td></tr>
<tr><td>2</td><td>креплением болтами и</td><td>С выверкой в одной</td><td>1,00</td><td>2,10</td><td>2,55</td><td>6,5</td><td colspan="2">7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>14,0</td><td>15,5</td><td>18,0</td></tr>
<tr><td>3</td><td rowspan="5">планками</td><td rowspan="2">плоскости</td><td>0,50</td><td>2,75</td><td>3,30</td><td>8,0</td><td colspan="2">9,0</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td>22,0</td></tr>
<tr><td>4</td><td>0,10</td><td>3,10</td><td>3,65</td><td>8,5</td><td colspan="2">10,0</td><td>11,0</td><td>13,0</td><td>15,5</td><td>18,0</td><td>21,0</td><td>24,0</td></tr>
<tr><td>5</td><td>С выверкой в двух</td><td>1,00</td><td>3,40</td><td>4,00</td><td>9,5</td><td colspan="2">11,0</td><td>12,5</td><td>15,0</td><td>17,5</td><td>20,0</td><td>23,0</td><td>26,5</td></tr>
<tr><td>6</td><td rowspan="2">плоскостях</td><td>0,50</td><td>4,00</td><td>5,00</td><td>12,0</td><td colspan="2">13,5</td><td>15,5</td><td>18,0</td><td>20,0</td><td>23,0</td><td>27,5</td><td>29,5</td></tr>
<tr><td>7</td><td>0,10</td><td>4,50</td><td>5,50</td><td>13,0</td><td colspan="2">15,0</td><td>17,0</td><td>20,0</td><td>22,0</td><td>25,5</td><td>29,5</td><td>33,0</td></tr>
<tr><td>8</td><td>На столе (плите) с</td><td>Без выверки</td><td>-</td><td>2,10</td><td>2,55</td><td>5,5</td><td colspan="2">6,0</td><td>7,0</td><td>9,0</td><td>10,0</td><td>12,0</td><td>14,5</td><td>17,0</td></tr>
<tr><td>9</td><td>домкратами, подставками</td><td>С выверкой в одной</td><td>1,00</td><td>2,95</td><td>3,65</td><td>7,5</td><td colspan="2">8,5</td><td>10,5</td><td>12,5</td><td>14,5</td><td>17,5</td><td>20,5</td><td>24,0</td></tr>
<tr><td>10</td><td>с креплением болтами</td><td rowspan="4">плоскости</td><td>0,50</td><td>3,75</td><td>4,50</td><td>9,0</td><td colspan="2">10,5</td><td>12,5</td><td>15,0</td><td>17,5</td><td>22,0</td><td>25,5</td><td>29,5</td></tr>
<tr><td>11</td><td rowspan="13">и планками</td><td>0,10</td><td>4,00</td><td>4,95</td><td>10,0</td><td colspan="2">11,5</td><td>13,5</td><td>16,5</td><td>20,0</td><td>24,0</td><td>27,5</td><td>33,0</td></tr>
<tr><td>12</td><td>0,05</td><td>5,00</td><td>6,00</td><td>12,0</td><td colspan="2">13,5</td><td>16,5</td><td>20,5</td><td>23,5</td><td>28,5</td><td>33,0</td><td>39,5</td></tr>
<tr><td>13</td><td>0,01</td><td>5,50</td><td>7,00</td><td>13,5</td><td colspan="2">16,0</td><td>18,5</td><td>23,0</td><td>27,5</td><td>33,0</td><td>37,5</td><td>45,0</td></tr>
<tr><td>14</td><td>С выверкой в двух</td><td>1,00</td><td>3,65</td><td>4,60</td><td>10,5</td><td colspan="2">12,5</td><td>14,5</td><td>16,5</td><td>20,0</td><td>22,0</td><td>25,5</td><td>29,5</td></tr>
<tr><td>15</td><td rowspan="4">плоскостях</td><td>0,50</td><td>4,60</td><td>6,00</td><td>12,5</td><td colspan="2">15,0</td><td>16,5</td><td>20,5</td><td>23,0</td><td>27,5</td><td>31,0</td><td>36,5</td></tr>
<tr><td>16</td><td>0,10</td><td>5,00</td><td>6,00</td><td>14,5</td><td colspan="2">16,5</td><td>18,5</td><td>22,0</td><td>25,5</td><td>29,5</td><td>34,0</td><td>39,5</td></tr>
<tr><td>17</td><td>0,05</td><td>6,00</td><td>7,50</td><td>17,0</td><td colspan="2">20,0</td><td>22,0</td><td>26,5</td><td>31,0</td><td>35,0</td><td>40,5</td><td>47,5</td></tr>
<tr><td>18</td><td>0,01</td><td>7,00</td><td>8,50</td><td>20,0</td><td colspan="2">23,0</td><td>25,5</td><td>31,0</td><td>35,0</td><td>40,5</td><td>47,5</td><td>54,0</td></tr>
<tr><td>19</td><td>С выверкой в трех</td><td>1,00</td><td>4,50</td><td>5,50</td><td>13,0</td><td colspan="2">15,5</td><td>17,5</td><td>21,0</td><td>24,0</td><td>27,5</td><td>32,0</td><td>37,5</td></tr>
<tr><td>20</td><td rowspan="4">плоскостях</td><td>0,50</td><td>6,00</td><td>7,00</td><td>16,0</td><td colspan="2">18,5</td><td>21,0</td><td>25,5</td><td>28,5</td><td>34,0</td><td>38,5</td><td>45,0</td></tr>
<tr><td>21</td><td>0,10</td><td>6,50</td><td>8,00</td><td>17,5</td><td colspan="2">20,5</td><td>23,0</td><td>27,5</td><td>32,0</td><td>37,5</td><td>43,0</td><td>49,5</td></tr>
<tr><td>22</td><td>0,05</td><td>7,50</td><td>9,50</td><td>21,0</td><td colspan="2">24,0</td><td>27,5</td><td>33,0</td><td>38,5</td><td>45,0</td><td>51,5</td><td>59,5</td></tr>
<tr><td>23</td><td>0,01</td><td>9,00</td><td>10,50</td><td>24,0</td><td colspan="2">27,5</td><td>32,0</td><td>38,5</td><td>44,0</td><td>51,5</td><td>59,5</td><td>68,0</td></tr>
<tr><td>24</td><td>На столе с угольником</td><td>Без выверки</td><td>-</td><td>1,85</td><td>2,00</td><td>5,0</td><td colspan="2">6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,0</td><td>14,5</td></tr>
<tr><td>25</td><td>с креплением болтами</td><td>С выверкой в одной</td><td>1,00</td><td>2,65</td><td>3,00</td><td>7,5</td><td colspan="2">8,5</td><td>10,0</td><td>11,5</td><td>13,0</td><td>15,5</td><td>17,5</td><td>21,0</td></tr>
<tr><td>26</td><td rowspan="7">и планками</td><td rowspan="4">плоскости</td><td>0,50</td><td>3,00</td><td>3,85</td><td>10,0</td><td colspan="2">11,0</td><td>13,0</td><td>15,0</td><td>16,5</td><td>20,0</td><td>23,0</td><td>27,5</td></tr>
<tr><td>27</td><td>0,10</td><td>3,50</td><td>4,00</td><td>10,5</td><td colspan="2">12,0</td><td>14,5</td><td>16,5</td><td>18,5</td><td>22,0</td><td>25,5</td><td>29,5</td></tr>
<tr><td>28</td><td>0,05</td><td>4,00</td><td>5,00</td><td>12,5</td><td colspan="2">14,5</td><td>17,0</td><td>20,0</td><td>22,0</td><td>26,5</td><td>31,0</td><td>35,0</td></tr>
<tr><td>29</td><td>0,01</td><td>5,00</td><td>6,00</td><td>14,5</td><td colspan="2">16,5</td><td>20,0</td><td>23,0</td><td>25,5</td><td>31,0</td><td>35,0</td><td>40,5</td></tr>
<tr><td>30</td><td>С выверкой в двух</td><td>1,00</td><td>3,65</td><td>4,50</td><td>10,5</td><td colspan="2">12,0</td><td>14,5</td><td>16,5</td><td>18,5</td><td>22,0</td><td>25,5</td><td>30,0</td></tr>
<tr><td>31</td><td rowspan="2">плоскостях</td><td>0,50</td><td>4,50</td><td>5,50</td><td>13,0</td><td colspan="2">14,5</td><td>17,0</td><td>20,0</td><td>23,0</td><td>27,5</td><td>31,0</td><td>36,5</td></tr>
<tr><td>32</td><td>0,10</td><td>5,00</td><td>6,00</td><td>14,5</td><td colspan="2">16,0</td><td>18,5</td><td>22,0</td><td>25,5</td><td>29,5</td><td>34,0</td><td>39,5</td></tr>
<tr><td></td><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="14%"><col width="14%"><col width="8%"><col width="6%"><col width="7%"><col width="6%"><col width="3%"><col width="2%"><col width="7%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="8" rowspan="2">Вспомогательное время на установку и снятие детали Единичное и мелкосерийное производство</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="7">Карта 3 Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Способ установки и</td><td rowspan="3">Характер выверки</td><td>Точность</td><td colspan="11">Масса детали, кг, до</td></tr>
<tr><td rowspan="2">крепление детали</td><td>выверки на</td><td>10</td><td>20</td><td>30</td><td colspan="2">50</td><td>100</td><td>200</td><td>400</td><td>800</td><td>1500</td><td>3000</td></tr>
<tr><td>1 пог. м, мм, до</td><td colspan="11">Время, мин.</td></tr>
<tr><td>33</td><td>На столе с угольником</td><td>С выверкой в двух</td><td>0,05</td><td>6,00</td><td>7,50</td><td>17</td><td colspan="2">19</td><td>22,0</td><td>26,5</td><td>31</td><td>35,0</td><td>39,5</td><td>47,5</td></tr>
<tr><td>34</td><td>с креплением болтами и планками</td><td>плоскостях</td><td>0,01</td><td>7,00</td><td>8,50</td><td>20</td><td colspan="2">22</td><td>25,5</td><td>29,5</td><td>35</td><td>40,5</td><td>47,5</td><td>54,0</td></tr>
<tr><td>35</td><td rowspan="6">На призмах с креплением болтами и планками</td><td>Без выверки</td><td>-</td><td>1,65</td><td>2,10</td><td>3,50</td><td colspan="2">3,95</td><td>4,95</td><td>6,0</td><td>7,0</td><td>8,5</td><td>-</td><td>-</td></tr>
<tr><td>36</td><td>С выверкой в одной</td><td>1,00</td><td>2,40</td><td>2,95</td><td>4,95</td><td colspan="2">5,50</td><td>7,0</td><td>8,5</td><td>10,5</td><td>12,0</td><td>14,5</td><td>17,5</td></tr>
<tr><td>37</td><td rowspan="4">плоскости</td><td>0,50</td><td>3,00</td><td>3,50</td><td>6,50</td><td colspan="2">7,50</td><td>9,5</td><td>11,0</td><td>13,0</td><td>16,5</td><td>20,0</td><td>24,0</td></tr>
<tr><td>38</td><td>0,10</td><td>3,50</td><td>4,00</td><td>7,00</td><td colspan="2">8,50</td><td>10,00</td><td>12,0</td><td>15,5</td><td>18,5</td><td>22,0</td><td>26,5</td></tr>
<tr><td>39</td><td>0,05</td><td>4,00</td><td>5,00</td><td>9,00</td><td colspan="2">10,0</td><td>12,00</td><td>15,5</td><td>18,5</td><td>22,0</td><td>26,5</td><td>32,0</td></tr>
<tr><td>40</td><td>0,01</td><td>5,00</td><td>6,00</td><td>10,0</td><td colspan="2">12,0</td><td>14,50</td><td>17,0</td><td>21,0</td><td>25,5</td><td>31,0</td><td>37,5</td></tr>
<tr><td>41</td><td colspan="3">Время в карте предусматривает крепление детали болтами в числе</td><td colspan="9">4</td><td colspan="2">6</td></tr>
<tr><td>42</td><td colspan="3">Добавлять (отнимать) на каждый болт сверх (менее) предусмотренных</td><td colspan="3">0,4</td><td colspan="6">0,5</td><td colspan="2">0,9</td></tr>
<tr><td></td><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>


<a id="p100432"></a>Примечания: 1. При установке деталей с необработанной установочной поверхностью табличное время принимать с коэффициентом К = 1,2.
2. <a id="p100433"></a>При установке деталей с применением двух кранов табличное время принимать с коэффициентом К = 1,3.
3. <a id="p100434"></a>При установке нежестких деталей сварной конструкции табличное время принимать с коэффициентом К = 1,2.
4. <a id="p100435"></a>При установке деталей в неустойчивом (на ребро) положении табличное время (поз. 8 - 23) принимать с коэффициентом К = 1,3.
5. <a id="p100436"></a>При креплении деталей гидрошайбами с гидро- и пневмоподставками табличное время принимать с коэффициентом К = 0,8.
6. <a id="p100437"></a>При переустановке деталей вручную время по карте принимать без изменений, при переустановке деталей с применением мостового крана без выверки табличное время принимать с коэффициентом К = 0,85, с выверкой в одной плоскости - с коэффициентом К = 0,8, с выверкой в двух-трех плоскостях - с коэффициентом К = 0,95.
7. <a id="p100438"></a>При работе с местным подъемником время по карте, приведенное для мостового крана, уменьшать на 1,5 мин.


<table>
<colgroup><col width="8%"><col width="19%"><col width="12%"><col width="14%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="11">Вспомогательное время на кантовку детали Горизонтально-расточные (в вертикальной плоскости) станки Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="11">Карта 4</td></tr>
<tr><td rowspan="3">N позиции</td><td>Угол поворота при кантовке,</td><td colspan="2" rowspan="3">Характер застропки</td><td colspan="7">Масса детали, кг, до</td></tr>
<tr><td rowspan="2">градус</td><td>50</td><td>100</td><td>200</td><td>400</td><td>800</td><td>1500</td><td>3000</td></tr>
<tr><td colspan="7">Время, мин.</td></tr>
<tr><td>1</td><td rowspan="2">90</td><td colspan="2">Удобная</td><td>1,20</td><td>1,50</td><td>1,85</td><td>2,25</td><td>2,80</td><td>3,35</td><td>4,1</td></tr>
<tr><td>2</td><td colspan="2">Неудобная</td><td>2,35</td><td>2,90</td><td>3,55</td><td>4,35</td><td>5,50</td><td>6,50</td><td>8,0</td></tr>
<tr><td>3</td><td rowspan="2">180</td><td colspan="2">Удобная</td><td>1,60</td><td>1,95</td><td>2,35</td><td>2,90</td><td>3,65</td><td>4,40</td><td>5,5</td></tr>
<tr><td>4</td><td colspan="2">Неудобная</td><td>3,25</td><td>4,00</td><td>5,00</td><td>6,00</td><td>7,50</td><td>9,00</td><td>11,0</td></tr>
<tr><td>5</td><td>Транспортировка детали</td><td rowspan="2">Расстояние перемещения, м,</td><td>50</td><td colspan="7">4,0</td></tr>
<tr><td>6</td><td>(туда и обратно) для</td><td>100</td><td colspan="7">5,5</td></tr>
<tr><td>7</td><td>кантовки</td><td>до</td><td>свыше 100</td><td colspan="7">7,5</td></tr>
<tr><td></td><td></td><td>Индекс</td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td></tr>
</table>


<a id="p100449"></a>Примечания: 1. Время на кантовку добавляется ко времени на установку и снятие детали в тех случаях, когда в процессе выполнения операции имеет место переустановки детали.
2. <a id="p100450"></a>Удобная застропка - при наличии у деталей просветов, выступов и т.п. для захвата стропами; неудобная застропка - сплошные детали застрапливаются снаружи петлей.
3. <a id="p100451"></a>Время на транспортировку добавляется ко времени на кантовку в случаях, когда деталь перемещается в сторону от станка на расстояние более 10 м.


<table>
<colgroup><col width="4%"><col width="8%"><col width="18%"><col width="5%"><col width="9%"><col width="8%"><col width="9%"><col width="2%"><col width="18%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="8">Вспомогательное время на приемы, связанные с обработкой поверхности, не включенные в комплексы</td><td colspan="4">Горизонтально-расточные станки</td></tr>
<tr><td colspan="8">Единичное и мелкосерийное производство</td><td>Карта 5</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="5">N позиции</td><td colspan="8" rowspan="5">Наименование приема</td><td colspan="3">Вид станков</td></tr>
<tr><td colspan="3">Столиковые</td></tr>
<tr><td colspan="3">Группа станков: диаметр шпинделя, мм, до</td></tr>
<tr><td>65</td><td>110</td><td>160</td></tr>
<tr><td colspan="3">Время, мин.</td></tr>
<tr><td>1</td><td>Установить</td><td colspan="2" rowspan="2">резец в оправку или борштангу</td><td colspan="5">без установки на размер</td><td>0,55</td><td>0,66</td><td>0,77</td></tr>
<tr><td>2</td><td rowspan="18">и снять</td><td colspan="5">с установкой на размер по шаблону или линейке</td><td>0,88</td><td>0,99</td><td>1,10</td></tr>
<tr><td>3</td><td colspan="2" rowspan="2">резец в резецдержатель на планшайбе</td><td colspan="5">проходной</td><td>1,32</td><td>1,43</td><td>1,65</td></tr>
<tr><td>4</td><td colspan="5">подрезной</td><td>1,55</td><td>1,65</td><td>1,85</td></tr>
<tr><td>5</td><td colspan="2">оправку или инструмент (расточную пластину,</td><td colspan="2">без крепления</td><td colspan="3">вручную</td><td>0,33</td><td>0,44</td><td>0,55</td></tr>
<tr><td>6</td><td colspan="2">зенкер, развертку, резцовую головку) в</td><td colspan="2" rowspan="2">с креплением клинов</td><td colspan="3">вручную</td><td>1,20</td><td>1,45</td><td>1,65</td></tr>
<tr><td>7</td><td colspan="2">конусе шпинделя</td><td colspan="3">краном</td><td>4,50</td><td>4,85</td><td>5,00</td></tr>
<tr><td>8</td><td rowspan="2">борштангу в конус шпинделя с креплением клином и втулку задней</td><td colspan="2" rowspan="4">без совмещения оси втулки задней стойки и борштанги</td><td rowspan="8">Длина борштанги, мм, до</td><td colspan="3">вручную</td><td>8,00</td><td>10,00</td><td>12,00</td></tr>
<tr><td>9</td><td>3000</td><td colspan="2" rowspan="3">краном</td><td>12,00</td><td>14,50</td><td>16,50</td></tr>
<tr><td>10</td><td rowspan="6">стойки</td><td>5000</td><td>-</td><td>18,50</td><td>23,00</td></tr>
<tr><td>11</td><td>8000</td><td>-</td><td>-</td><td>29,50</td></tr>
<tr><td>12</td><td colspan="2">с совмещением оси втулки</td><td colspan="3">вручную</td><td>14,50</td><td>16,50</td><td>18,50</td></tr>
<tr><td>13</td><td colspan="2" rowspan="3">задней стойки и борштанги</td><td>3000</td><td colspan="2" rowspan="3">краном</td><td>18,50</td><td>21,00</td><td>23,00</td></tr>
<tr><td>14</td><td>5000</td><td>-</td><td>29,50</td><td>32,00</td></tr>
<tr><td>15</td><td>8000</td><td>-</td><td>-</td><td>42,00</td></tr>
<tr><td>16</td><td>фрезу на оправку с креплением</td><td colspan="2" rowspan="3">диаметр фрезы, мм, до</td><td colspan="4">200</td><td>2,00</td><td>2,20</td><td>2,75</td></tr>
<tr><td>17</td><td rowspan="2">болтами</td><td colspan="4">320</td><td>-</td><td>2,75</td><td>3,85</td></tr>
<tr><td>18</td><td colspan="4">450</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>19</td><td colspan="7">упор подачи (для поворота звездочки) летучего суппорта</td><td>0,77</td><td>0,88</td><td>1,10</td></tr>
<tr><td>20</td><td colspan="2">Повернуть стол на угол с откреплением и</td><td colspan="3" rowspan="2">с проверкой угла по шкале деления</td><td>Угол поворота</td><td colspan="2">90</td><td>1,10</td><td>1,35</td><td>1,65</td></tr>
<tr><td>21</td><td colspan="2" rowspan="3">закреплением</td><td rowspan="3">стола, град.</td><td colspan="2">180</td><td>1,75</td><td>2,10</td><td>2,55</td></tr>
<tr><td>22</td><td colspan="3" rowspan="2">с совмещением осей в другой плоскости</td><td colspan="2">90</td><td>2,00</td><td>2,40</td><td>3,05</td></tr>
<tr><td>23</td><td colspan="2">180</td><td>3,05</td><td>3,65</td><td>4,50</td></tr>
<tr><td></td><td colspan="2"></td><td colspan="3">Индекс</td><td></td><td colspan="2"></td><td>а</td><td>б</td><td>в</td></tr>
</table>


<a id="p100478"></a>*Примечание.* При установке резца в оправку или борштангу в стесненных условиях (через окна детали или приспособлений) табличное время (поз. 1 - 2) принимать с коэффициентом К = 1,2.


<table>
<colgroup><col width="4%"><col width="8%"><col width="10%"><col width="11%"><col width="6%"><col width="7%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="9">Вспомогательное время на приемы, связанные с обработкой поверхности, не включенные в комплексы</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="9">Единичное и мелкосерийное производство</td><td colspan="3">Карта 5</td><td colspan="3">Лист 2</td></tr>
<tr><td colspan="15">Совмещение оси шпинделя с осью обрабатываемого отверстия</td></tr>
<tr><td rowspan="5">N позиции</td><td colspan="2">База для совмещения оси шпинделя</td><td rowspan="5">Способ совмещения</td><td rowspan="5">Перемещение шпинделя в направлении</td><td>Точность</td><td colspan="9">Группа станков: диаметр шпинделя, мм, до</td></tr>
<tr><td colspan="2" rowspan="4">с осью обрабатываемого отверстия</td><td>совмещения,</td><td colspan="3">65</td><td colspan="3">110</td><td colspan="3">160</td></tr>
<tr><td rowspan="3">мм, до</td><td colspan="9">Длина перемещения, мм, до</td></tr>
<tr><td>300</td><td>600</td><td>1000</td><td>300</td><td>600</td><td>1000</td><td>300</td><td>600</td><td>1000</td></tr>
<tr><td colspan="9">Время, мин.</td></tr>
<tr><td>24</td><td colspan="2" rowspan="4">Разметка необработанного отверстия</td><td>Иглой в шпинделе</td><td>1</td><td>1,0</td><td>1,85</td><td>2,10</td><td>2,40</td><td>2,30</td><td>2,55</td><td>2,85</td><td>2,75</td><td>2,95</td><td>3,30</td></tr>
<tr><td>25</td><td>по размеченной окружности</td><td>2</td><td></td><td>2,40</td><td>2,75</td><td>3,20</td><td>3,05</td><td>3,40</td><td>3,85</td><td>3,75</td><td>4,05</td><td>4,50</td></tr>
<tr><td>26</td><td>Центром по разметке</td><td>1</td><td>1,0</td><td>0,33</td><td>0,55</td><td>0,88</td><td>0,44</td><td>0,66</td><td>0,99</td><td>0,55</td><td>0,77</td><td>1,10</td></tr>
<tr><td>27</td><td>керном</td><td>2</td><td></td><td>0,44</td><td>0,77</td><td>1,20</td><td>0,55</td><td>0,88</td><td>1,30</td><td>0,66</td><td>0,99</td><td>1,45</td></tr>
<tr><td>28</td><td colspan="2" rowspan="4">Отверстие кондуктора</td><td rowspan="2">По индикатору</td><td>1</td><td>-</td><td>4,05</td><td>4,40</td><td>4,75</td><td>5,00</td><td>5,00</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,00</td></tr>
<tr><td>29</td><td>2</td><td>-</td><td>5,00</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,00</td><td>7,50</td><td>8,00</td><td>8,00</td><td>8,50</td></tr>
<tr><td>30</td><td>По кондукторной</td><td>1</td><td>-</td><td>2,10</td><td>2,40</td><td>2,75</td><td>2,55</td><td>2,75</td><td>3,20</td><td>2,85</td><td>3,20</td><td>3,50</td></tr>
<tr><td>31</td><td>втулке и контрольной оправке</td><td>2</td><td>-</td><td>2,85</td><td>3,30</td><td>3,85</td><td>3,40</td><td>3,85</td><td>4,40</td><td>4,05</td><td>4,50</td><td>5,00</td></tr>
<tr><td>32</td><td>Обработанное</td><td rowspan="4">без пробных стружек</td><td>По нониусной или</td><td>1</td><td>1,0</td><td>0,44</td><td>0,66</td><td>1,10</td><td>0,55</td><td>0,77</td><td>1,20</td><td>0,66</td><td>0,88</td><td>1,30</td></tr>
<tr><td>33</td><td rowspan="3">отверстие</td><td rowspan="3">масштабной линейке</td><td>2</td><td>0,3</td><td>1,55</td><td>1,85</td><td>2,20</td><td>1,98</td><td>2,20</td><td>2,65</td><td>2,40</td><td>2,75</td><td>3,05</td></tr>
<tr><td>34</td><td>1</td><td>1,0</td><td>0,55</td><td>0,88</td><td>1,45</td><td>0,66</td><td>1,10</td><td>1,55</td><td>0,77</td><td>1,20</td><td>1,75</td></tr>
<tr><td>35</td><td>2</td><td>0,3</td><td>2,40</td><td>2,75</td><td>3,31</td><td>2,85</td><td>3,30</td><td>3,85</td><td>3,50</td><td>3,95</td><td>4,50</td></tr>
<tr><td>36</td><td rowspan="6">Необработанное отверстие</td><td rowspan="6">без пробных стружек</td><td rowspan="4">По штихмасу или измерительным плиткам с помощью контрольных валиков</td><td>1</td><td>0,5</td><td>4,00</td><td>5,00</td><td>6,00</td><td>5,00</td><td>6,00</td><td>7,50</td><td>6,00</td><td>7,50</td><td>9,00</td></tr>
<tr><td>37</td><td>2</td><td>0,1</td><td>6,00</td><td>8,00</td><td>9,00</td><td>7,50</td><td>9,50</td><td>11,00</td><td>9,00</td><td>11,00</td><td>13,00</td></tr>
<tr><td>38</td><td>1</td><td>0,5</td><td>7,00</td><td>8,50</td><td>10,50</td><td>8,50</td><td>10,50</td><td>12,00</td><td>10,00</td><td>12,00</td><td>15,50</td></tr>
<tr><td>39</td><td>2</td><td>0,1</td><td>8,50</td><td>10,50</td><td>12,00</td><td>10,50</td><td>12,00</td><td>14,50</td><td>12,00</td><td>14,50</td><td>17,50</td></tr>
<tr><td>40</td><td rowspan="2">По индикатору</td><td>1</td><td>0,5</td><td>5,50</td><td>7,00</td><td>9,00</td><td>7,00</td><td>8,00</td><td>11,00</td><td>8,00</td><td>10,00</td><td>13,00</td></tr>
<tr><td>41</td><td>2</td><td>0,5</td><td>8,00</td><td>9,50</td><td>13,00</td><td>9,50</td><td>12,00</td><td>15,50</td><td>12,00</td><td>14,50</td><td>18,50</td></tr>
<tr><td>42</td><td colspan="2" rowspan="2">Обработанное отверстие</td><td>По консольной</td><td>1</td><td>-</td><td>0,22</td><td>0,44</td><td>0,66</td><td>0,44</td><td>0,55</td><td>0,88</td><td>0,44</td><td>0,66</td><td>1,10</td></tr>
<tr><td>43</td><td>резцовой оправке</td><td>2</td><td>-</td><td>0,33</td><td>0,55</td><td>0,88</td><td>0,55</td><td>0,66</td><td>0,99</td><td>0,66</td><td>0,88</td><td>1,21</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="18%"><col width="11%"><col width="6%"><col width="7%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="8">Вспомогательное время на приемы, связанные с обработкой поверхности, не включенные в комплексы</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="8">Единичное и мелкосерийное производство</td><td colspan="3">Карта 5</td><td colspan="3">Лист 3</td></tr>
<tr><td colspan="14">Совмещение оси шпинделя с осью обрабатываемого отверстия</td></tr>
<tr><td rowspan="5">N позиции</td><td>База для совмещения оси шпинделя</td><td rowspan="5">Способ совмещения</td><td rowspan="5">Перемещение шпинделя в направлении</td><td>Точность</td><td colspan="9">Группа станков: диаметр шпинделя, мм, до</td></tr>
<tr><td rowspan="4">с осью обрабатываемого отверстия</td><td>совмещения,</td><td colspan="3">65</td><td colspan="3">110</td><td colspan="3">160</td></tr>
<tr><td rowspan="3">мм, до</td><td colspan="9">Длина перемещения, мм, до</td></tr>
<tr><td>300</td><td>600</td><td>1000</td><td>300</td><td>600</td><td>1000</td><td>300</td><td>600</td><td>1000</td></tr>
<tr><td colspan="9">Время, мин.</td></tr>
<tr><td>44</td><td>Наружная боковая поверхность</td><td>По нониусной или</td><td rowspan="2">1</td><td>1,0</td><td>0,44</td><td>0,66</td><td>1,10</td><td>0,55</td><td>0,77</td><td>1,20</td><td>0,66</td><td>0,88</td><td>1,30</td></tr>
<tr><td>45</td><td rowspan="7">детали</td><td rowspan="3">масштабной линейке</td><td>0,3</td><td>1,55</td><td>1,85</td><td>2,20</td><td>1,85</td><td>2,10</td><td>2,55</td><td>2,20</td><td>2,55</td><td>2,85</td></tr>
<tr><td>46</td><td rowspan="2">2</td><td>1,0</td><td>0,55</td><td>0,88</td><td>1,45</td><td>0,66</td><td>1,10</td><td>1,55</td><td>0,77</td><td>1,20</td><td>1,65</td></tr>
<tr><td>47</td><td>0,3</td><td>2,40</td><td>2,75</td><td>3,30</td><td>2,75</td><td>3,20</td><td>3,65</td><td>3,40</td><td>3,85</td><td>4,40</td></tr>
<tr><td>48</td><td rowspan="2">По штихмасу</td><td rowspan="2">1</td><td>0,5</td><td>2,55</td><td>3,20</td><td>3,95</td><td>3,20</td><td>3,85</td><td>4,60</td><td>3,85</td><td>4,75</td><td>5,60</td></tr>
<tr><td>49</td><td>0,1</td><td>3,50</td><td>4,40</td><td>5,50</td><td>4,40</td><td>5,50</td><td>6,50</td><td>5,50</td><td>6,50</td><td>7,50</td></tr>
<tr><td>50</td><td>По измерительным</td><td rowspan="2">2</td><td>0,5</td><td>3,65</td><td>4,65</td><td>5,50</td><td>4,40</td><td>5,50</td><td>6,50</td><td>5,50</td><td>6,50</td><td>8,00</td></tr>
<tr><td>51</td><td>плиткам</td><td>0,1</td><td>7,00</td><td>8,50</td><td>11,00</td><td>8,00</td><td>10</td><td>12,00</td><td>9,50</td><td>11,00</td><td>13,00</td></tr>
<tr><td>52</td><td>Обработанное отверстие и</td><td rowspan="2">По штихмасу или измерительным плиткам</td><td rowspan="2">1 - 2</td><td>0,5</td><td>4,60</td><td>5,50</td><td>7,00</td><td>5,50</td><td>7,00</td><td>8,50</td><td>8,50</td><td>11,00</td><td>13,00</td></tr>
<tr><td>53</td><td>плоскость</td><td>0,1</td><td>6,00</td><td>7,50</td><td>8,50</td><td>7,00</td><td>9,00</td><td>10,50</td><td>11,00</td><td>13,00</td><td>16,50</td></tr>
<tr><td>54</td><td colspan="2">Поворот стола при совмещении оси в другой плоскости на</td><td>90</td><td></td><td></td><td>1,85</td><td></td><td></td><td>2,2</td><td></td><td colspan="2">2,85</td><td></td></tr>
<tr><td>55</td><td colspan="2">угол</td><td>180</td><td></td><td></td><td>2,75</td><td></td><td></td><td>3,3</td><td></td><td colspan="2">3,95</td><td></td></tr>
<tr><td></td><td colspan="2">Индекс</td><td></td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p100519"></a>Примечания: 1. При совмещении осей с труднодоступными измерениями (измерения внутри корпуса и закрытых местах, измерения от закрытого базового отверстия и т.п.) табличное время принимать с коэффициентом К = 1,4.
2. <a id="p100520"></a>При повороте стола на угол с проверкой по индикатору табличное время (поз. 54 - 55) принимать с коэффициентом К = 2,0.
3. <a id="p100521"></a>При совмещении осей на станках с цифровой индикацией время определяется согласно паспортным данным станка для быстрого перемещения с учетом 0,3 мин. на набор необходимого размера.


<table>
<colgroup><col width="5%"><col width="14%"><col width="12%"><col width="9%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="14">Вспомогательное время на приемку деталей на станке Горизонтально-расточные станки</td></tr>
<tr><td colspan="14">Карта 6</td></tr>
<tr><td rowspan="3">N позиции</td><td>Характер контрольных</td><td>Квалитет (класс</td><td>Масса детали,</td><td colspan="10">Число определяемых размеров</td></tr>
<tr><td rowspan="2">измерений</td><td rowspan="2">точности)</td><td rowspan="2">т, до</td><td>3</td><td>5</td><td>7</td><td>10</td><td>15</td><td>20</td><td>30</td><td>45</td><td>65</td><td>100</td></tr>
<tr><td colspan="10">Время, мин.</td></tr>
<tr><td>1</td><td>Проверка чистоты и</td><td>1Т14 - 1Т11</td><td>5</td><td>4,9</td><td>5,0</td><td>8,0</td><td>9,5</td><td>11,0</td><td>13,0</td><td>15,5</td><td>19,5</td><td>23,0</td><td>27,5</td></tr>
<tr><td>2</td><td>точности диаметра</td><td rowspan="5">(7 - 4)</td><td>10</td><td>6,0</td><td>8,5</td><td>10,0</td><td>12,0</td><td>13,5</td><td>15,5</td><td>19,5</td><td>24,0</td><td>28,5</td><td>34,0</td></tr>
<tr><td>3</td><td rowspan="2">отверстий, их межцентровых расстояний и</td><td>20</td><td>7,5</td><td>10,0</td><td>12,0</td><td>13,5</td><td>16,5</td><td>19,5</td><td>24,0</td><td>28,5</td><td>34,0</td><td>42,5</td></tr>
<tr><td>4</td><td>30</td><td>8,5</td><td>12,0</td><td>13,5</td><td>15,5</td><td>19,5</td><td>23,0</td><td>27,5</td><td>33,0</td><td>39,5</td><td>48,0</td></tr>
<tr><td>5</td><td rowspan="14">точности обработанных плоскостей</td><td>60</td><td>10,5</td><td>13,5</td><td>16,5</td><td>19,5</td><td>24,0</td><td>27,5</td><td>34,0</td><td>40,5</td><td>48,0</td><td>59,0</td></tr>
<tr><td>6</td><td>&gt; 60</td><td>12,0</td><td>16,5</td><td>19,5</td><td>23,0</td><td>27,5</td><td>31,5</td><td>38,5</td><td>47,0</td><td>56,0</td><td>69,0</td></tr>
<tr><td>7</td><td rowspan="6">1Т9 (3)</td><td>5</td><td>6,0</td><td>7,0</td><td>9,5</td><td>11,0</td><td>13,0</td><td>15,5</td><td>18,5</td><td>24,0</td><td>27,5</td><td>33,0</td></tr>
<tr><td>8</td><td>10</td><td>7,5</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td>24,0</td><td>28,5</td><td>34,0</td><td>40,5</td></tr>
<tr><td>9</td><td>20</td><td>9,0</td><td>12,0</td><td>14,0</td><td>16,5</td><td>19,5</td><td>24,0</td><td>28,5</td><td>34,0</td><td>40,5</td><td>52,0</td></tr>
<tr><td>10</td><td>30</td><td>10,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td>24,0</td><td>27,5</td><td>33,0</td><td>39,5</td><td>47,0</td><td>58,0</td></tr>
<tr><td>11</td><td>60</td><td>12,0</td><td>16,5</td><td>19,5</td><td>24,0</td><td>28,5</td><td>33,0</td><td>40,5</td><td>48,0</td><td>58,0</td><td>71,0</td></tr>
<tr><td>12</td><td>&gt; 60</td><td>14,0</td><td>19,5</td><td>24,0</td><td>27,5</td><td>33,0</td><td>38,5</td><td>46,0</td><td>57,0</td><td>67,0</td><td>83,0</td></tr>
<tr><td>13</td><td rowspan="6">1Т7 (2)</td><td>5</td><td>7,0</td><td>8,5</td><td>11,0</td><td>13,0</td><td>15,5</td><td>18,5</td><td>22,0</td><td>28,5</td><td>33,0</td><td>39,5</td></tr>
<tr><td>14</td><td>10</td><td>9,0</td><td>12,0</td><td>14,0</td><td>17,5</td><td>19,5</td><td>22,0</td><td>28,5</td><td>34,0</td><td>40,5</td><td>48,0</td></tr>
<tr><td>15</td><td>20</td><td>11,0</td><td>14,0</td><td>17,5</td><td>19,5</td><td>24,0</td><td>28,5</td><td>34,0</td><td>40,5</td><td>48,0</td><td>61,0</td></tr>
<tr><td>16</td><td>30</td><td>12,0</td><td>17,5</td><td>19,5</td><td>22,0</td><td>28,5</td><td>33,0</td><td>39,5</td><td>47,0</td><td>57,0</td><td>70,0</td></tr>
<tr><td>17</td><td>60</td><td>14,0</td><td>19,5</td><td>24,0</td><td>28,5</td><td>34,0</td><td>39,5</td><td>48,0</td><td>58,0</td><td>69,0</td><td>85,0</td></tr>
<tr><td>18</td><td>&gt; 60</td><td>17,5</td><td>24,0</td><td>28,5</td><td>33,0</td><td>39,5</td><td>46,0</td><td>55,0</td><td>68,0</td><td>80,0</td><td>100,0</td></tr>
<tr><td>19</td><td>То же с проверкой</td><td>1Т11 - 1Т9</td><td>5</td><td>8,0</td><td>9,5</td><td>13,0</td><td>14,0</td><td>17,5</td><td>21,0</td><td>25,0</td><td>33,0</td><td>37,0</td><td>44,0</td></tr>
<tr><td>20</td><td rowspan="2">параллельности плоскостей и осей</td><td rowspan="5">(4 - 3)</td><td>10</td><td>10,0</td><td>13,0</td><td>16,5</td><td>18,5</td><td>22,0</td><td>25,0</td><td>33,0</td><td>38,5</td><td>46,0</td><td>55,0</td></tr>
<tr><td>21</td><td>20</td><td>12,0</td><td>16,5</td><td>19,5</td><td>22,0</td><td>26,0</td><td>33,0</td><td>38,5</td><td>46,0</td><td>55,0</td><td>70,0</td></tr>
<tr><td>22</td><td rowspan="9">отверстий</td><td>30</td><td>13,5</td><td>19,5</td><td>22,0</td><td>25,0</td><td>33,0</td><td>37,0</td><td>44,0</td><td>54,0</td><td>64,0</td><td>79,0</td></tr>
<tr><td>23</td><td>60</td><td>16,5</td><td>22,0</td><td>26,0</td><td>33,0</td><td>38,5</td><td>44,0</td><td>55,0</td><td>66,0</td><td>79,0</td><td>96,0</td></tr>
<tr><td>24</td><td>&gt; 60</td><td>20,0</td><td>26,0</td><td>33,0</td><td>37,0</td><td>44,0</td><td>51,0</td><td>62,0</td><td>77,0</td><td>90,0</td><td>110</td></tr>
<tr><td>25</td><td rowspan="6">1Т7 (2)</td><td>5</td><td>10,0</td><td>12,0</td><td>15,5</td><td>17,5</td><td>21,0</td><td>25,0</td><td>30,5</td><td>40,0</td><td>45,0</td><td>53,0</td></tr>
<tr><td>26</td><td>10</td><td>12,0</td><td>15,5</td><td>20,0</td><td>22,0</td><td>26,0</td><td>30,5</td><td>40,0</td><td>46,0</td><td>55,0</td><td>66,0</td></tr>
<tr><td>27</td><td>20</td><td>14,0</td><td>20,0</td><td>24,0</td><td>26,0</td><td>32,0</td><td>40,0</td><td>46,0</td><td>55,0</td><td>66,0</td><td>84,0</td></tr>
<tr><td>28</td><td>30</td><td>16,5</td><td>24,0</td><td>26,0</td><td>30,5</td><td>40,0</td><td>45,0</td><td>53,0</td><td>65,0</td><td>77,0</td><td>94,0</td></tr>
<tr><td>29</td><td>60</td><td>20,0</td><td>26,0</td><td>32,0</td><td>39,5</td><td>46,0</td><td>53,0</td><td>66,0</td><td>79,0</td><td>94,0</td><td>115,0</td></tr>
<tr><td>30</td><td>&gt; 60</td><td>24,0</td><td>32,0</td><td>39,5</td><td>45,0</td><td>53,0</td><td>61,0</td><td>75,0</td><td>92,0</td><td>107,0</td><td>131,0</td></tr>
<tr><td></td><td>Индекс</td><td></td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td></tr>
</table>


<a id="p100555"></a>Примечания: 1. Время на приемку детали на станке контролером или мастером включается в норму станочника в тех случаях, когда оно не перекрывается временем на другие работы и присутствие станочника при приемке детали предусмотрено технологическим процессом.
2. <a id="p100556"></a>Время рассчитано на контроль детали универсальными инструментами и измерительными приспособлениями при основных методах проверки. В случаях контроля с выполнением специальных неосвоенных наладок измерительных приспособлений или при необходимости выполнения сложных расчетов координат время по карте принимать с коэффициентом К = 1,3.


#### <a id="p100557"></a>4.2. НЕПОЛНОЕ ШТУЧНОЕ ВРЕМЯ



<table>
<colgroup><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="26">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="26">Чугун серый, НВ = 1,76 - 2,15 ГПа Борштанги консольные Единичное и мелкосерийное производство Резцы с пластинками ВК8</td></tr>
<tr><td colspan="21">Карта 7</td><td colspan="5">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td>Глубина</td><td colspan="18">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемого отверстия D, мм, до</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="18">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="15">10</td><td>30</td><td>2</td><td>1,15</td><td>1,25</td><td>1,35</td><td>1,40</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,40</td><td>750</td><td>70</td><td>1,2</td></tr>
<tr><td>2</td><td rowspan="2">48</td><td>3</td><td>1,15</td><td>1,30</td><td>1,45</td><td>1,55</td><td>1,90</td><td>2,05</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,45</td><td rowspan="2">480</td><td rowspan="2">72</td><td>1,4</td></tr>
<tr><td>3</td><td>5</td><td>1,20</td><td>1,35</td><td>1,50</td><td>1,65</td><td>2,00</td><td>2,15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,40</td><td>2,9</td></tr>
<tr><td>4</td><td rowspan="2">60</td><td>3</td><td>1,20</td><td>1,30</td><td>1,45</td><td>1,55</td><td>1,90</td><td>2,05</td><td>2,20</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,70</td><td rowspan="2">300</td><td rowspan="2">57</td><td>1,7</td></tr>
<tr><td>5</td><td>5</td><td>1,25</td><td>1,40</td><td>1,50</td><td>1,75</td><td>2,15</td><td>2,35</td><td>2,55</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,50</td><td>2,9</td></tr>
<tr><td>6</td><td rowspan="3">75</td><td>3</td><td>1,20</td><td>1,35</td><td>1,50</td><td>1,70</td><td>2,05</td><td>2,25</td><td>2,40</td><td>2,55</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,70</td><td rowspan="3">240</td><td rowspan="3">57</td><td>1,7</td></tr>
<tr><td>7</td><td>5</td><td>1,25</td><td>1,45</td><td>1,65</td><td>1,85</td><td>2,25</td><td>2,50</td><td>2,70</td><td>2,90</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,56</td><td>2,9</td></tr>
<tr><td>8</td><td>8</td><td>1,35</td><td>1,70</td><td>2,00</td><td>2,35</td><td>2,90</td><td>3,20</td><td>3,54</td><td>3,85</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,35</td><td>2,9</td></tr>
<tr><td>9</td><td rowspan="3">96</td><td>3</td><td>1,25</td><td>1,45</td><td>1,65</td><td>1,90</td><td>2,35</td><td>2,55</td><td>2,80</td><td>3,00</td><td>3,35</td><td>3,75</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,70</td><td rowspan="3">190</td><td rowspan="3">57</td><td>1,7</td></tr>
<tr><td>10</td><td>5</td><td>1,30</td><td>1,55</td><td>1,80</td><td>2,05</td><td>2,55</td><td>2,80</td><td>3,05</td><td>3,30</td><td>3,70</td><td>4,20</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,56</td><td>2,4</td></tr>
<tr><td>11</td><td>8</td><td>1,45</td><td>1,90</td><td>2,30</td><td>2,75</td><td>2,40</td><td>3,85</td><td>4,30</td><td>4,75</td><td>5,50</td><td>6,50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,35</td><td>2,9</td></tr>
<tr><td>12</td><td rowspan="4">120</td><td>3</td><td>1,25</td><td>1,50</td><td>1,80</td><td>2,05</td><td>2,50</td><td>2,80</td><td>3,05</td><td>3,30</td><td>3,70</td><td>4,20</td><td>4,85</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,70</td><td rowspan="4">150</td><td rowspan="4">56</td><td>1,7</td></tr>
<tr><td>13</td><td>5</td><td>1,30</td><td>1,65</td><td>1,95</td><td>2,30</td><td>2,85</td><td>3,15</td><td>3,50</td><td>3,80</td><td>4,30</td><td>5,00</td><td>6,00</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,56</td><td>2,4</td></tr>
<tr><td>14</td><td>8</td><td>1,41</td><td>1,80</td><td>2,25</td><td>2,65</td><td>3,25</td><td>3,70</td><td>4,10</td><td>4,50</td><td>5,00</td><td>6,00</td><td>7,00</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,45</td><td>2,9</td></tr>
<tr><td>15</td><td>12</td><td>1,55</td><td>2,05</td><td>2,60</td><td>3,15</td><td>3,85</td><td>4,40</td><td>4,95</td><td>5,50</td><td>6,00</td><td>7,50</td><td>8,50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,35</td><td>4,1</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td colspan="2">с</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="26">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="26">Чугун серый, НВ = 1,76 - 2,15 ГПа Борштанги консольные Единичное и мелкосерийное производство Резцы с пластинками ВК8</td></tr>
<tr><td colspan="21">Карта 7</td><td colspan="5">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td>Глубина</td><td colspan="18">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемого отверстия D, мм, до</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="18">Время на проход, мин.</td></tr>
<tr><td>16</td><td rowspan="16">10</td><td rowspan="4">150</td><td>3</td><td>1,30</td><td>1,60</td><td>1,95</td><td>2,25</td><td>2,80</td><td>3,15</td><td>3,45</td><td>3,80</td><td>4,3</td><td>4,95</td><td>5,5</td><td>6,5</td><td>7,0</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,70</td><td rowspan="4">120</td><td rowspan="4">56</td><td>1,7</td></tr>
<tr><td>17</td><td>5</td><td>1,40</td><td>1,80</td><td>2,20</td><td>2,60</td><td>3,25</td><td>3,65</td><td>4,05</td><td>4,45</td><td>5,0</td><td>6,00</td><td>7,0</td><td>8,0</td><td>8,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,56</td><td>2,4</td></tr>
<tr><td>18</td><td>8</td><td>1,50</td><td>2,00</td><td>2,50</td><td>3,00</td><td>3,75</td><td>4,25</td><td>4,75</td><td>5,00</td><td>6,0</td><td>7,00</td><td>8,0</td><td>9,0</td><td>10,0</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,45</td><td>2,9</td></tr>
<tr><td>19</td><td>12</td><td>1,65</td><td>2,30</td><td>2,95</td><td>3,60</td><td>4,50</td><td>5,00</td><td>6,00</td><td>6,50</td><td>7,5</td><td>9,00</td><td>10,0</td><td>11,5</td><td>13,0</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>0,35</td><td>4,1</td></tr>
<tr><td>20</td><td rowspan="4">190</td><td>3</td><td>1,35</td><td>1,80</td><td>2,25</td><td>2,70</td><td>3,35</td><td>3,80</td><td>4,25</td><td>4,70</td><td>5,5</td><td>6,00</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,0</td><td>11,5</td><td>-</td><td colspan="2">-</td><td>0,70</td><td rowspan="4">96</td><td rowspan="4">57</td><td>1,7</td></tr>
<tr><td>21</td><td>5</td><td>1,45</td><td>1,95</td><td>2,45</td><td>2,95</td><td>3,70</td><td>4,20</td><td>4,70</td><td>5,00</td><td>6,0</td><td>7,00</td><td>8,0</td><td>9,0</td><td>10,0</td><td>11,0</td><td>13,0</td><td>-</td><td colspan="2">-</td><td>0,56</td><td>2,4</td></tr>
<tr><td>22</td><td>8</td><td>1,60</td><td>2,25</td><td>2,85</td><td>3,50</td><td>4,35</td><td>5,00</td><td>5,50</td><td>6,00</td><td>7,0</td><td>8,50</td><td>10,0</td><td>11,0</td><td>12,5</td><td>14,0</td><td>16,0</td><td>-</td><td colspan="2">-</td><td>0,45</td><td>2,9</td></tr>
<tr><td>23</td><td>12</td><td>1,80</td><td>2,65</td><td>3,45</td><td>4,30</td><td>5,50</td><td>6,00</td><td>7,00</td><td>8,00</td><td>9,0</td><td>11,00</td><td>12,5</td><td>14,0</td><td>16,0</td><td>17,5</td><td>20,0</td><td>-</td><td colspan="2">-</td><td>0,35</td><td>4,1</td></tr>
<tr><td>24</td><td rowspan="4">240</td><td>3</td><td>1,42</td><td>1,95</td><td>2,45</td><td>3,00</td><td>3,75</td><td>4,25</td><td>4,80</td><td>5,50</td><td>6,0</td><td>7,00</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,5</td><td>13,0</td><td>16,0</td><td colspan="2">2,10</td><td>0,70</td><td rowspan="4">75</td><td rowspan="4">56</td><td>1,7</td></tr>
<tr><td>25</td><td>5</td><td>1,55</td><td>2,20</td><td>2,85</td><td>3,50</td><td>4,40</td><td>5,00</td><td>5,50</td><td>6,50</td><td>7,5</td><td>8,50</td><td>10,0</td><td>11,5</td><td>12,5</td><td>14,0</td><td>16,0</td><td>19,0</td><td colspan="2">2,60</td><td>0,56</td><td>2,4</td></tr>
<tr><td>26</td><td>8</td><td>1,70</td><td>2,55</td><td>3,35</td><td>4,15</td><td>5,00</td><td>6,00</td><td>7,00</td><td>7,50</td><td>9,0</td><td>10,50</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td>19,5</td><td>23,5</td><td colspan="2">3,25</td><td>0,45</td><td>2,9</td></tr>
<tr><td>27</td><td>12</td><td>2,00</td><td>3,05</td><td>4,10</td><td>5,00</td><td>6,50</td><td>7,50</td><td>8,50</td><td>9,50</td><td>11,0</td><td>13,00</td><td>15,5</td><td>17,5</td><td>20,0</td><td>22,0</td><td>25,0</td><td>30,5</td><td colspan="2">4,15</td><td>0,35</td><td>4,1</td></tr>
<tr><td>28</td><td rowspan="4">300</td><td>3</td><td>1,50</td><td>2,15</td><td>2,80</td><td>3,45</td><td>4,35</td><td>5,00</td><td>5,50</td><td>6,50</td><td>7,5</td><td>8,50</td><td>10,0</td><td>11,5</td><td>12,5</td><td>14,0</td><td>16,0</td><td>19,0</td><td colspan="2">2,60</td><td>0,70</td><td rowspan="4">60</td><td rowspan="4">36</td><td>1,7</td></tr>
<tr><td>29</td><td>5</td><td>1,65</td><td>2,45</td><td>3,25</td><td>4,05</td><td>5,00</td><td>6,00</td><td>7,00</td><td>7,50</td><td>9,0</td><td>10,50</td><td>12,0</td><td>13,5</td><td>15,5</td><td>17,0</td><td>19,5</td><td>23,5</td><td colspan="2">3,25</td><td>0,56</td><td>2,4</td></tr>
<tr><td>30</td><td>8</td><td>1,90</td><td>2,90</td><td>3,90</td><td>4,95</td><td>6,00</td><td>7,00</td><td>8,00</td><td>9,00</td><td>11,0</td><td>13,00</td><td>15,0</td><td>17,0</td><td>19,0</td><td>21,0</td><td>24,0</td><td>29,0</td><td colspan="2">4,05</td><td>0,45</td><td>2,9</td></tr>
<tr><td>31</td><td>12</td><td>2,20</td><td>3,50</td><td>4,80</td><td>6,00</td><td>7,50</td><td>9,00</td><td>10,5</td><td>11,5</td><td>13,5</td><td>16,00</td><td>19,0</td><td>21,5</td><td>24,0</td><td>26,5</td><td>30,5</td><td>37,0</td><td colspan="2">5,00</td><td>0,35</td><td>4,1</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td colspan="2">с</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="28">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="28">Чугун серый, НВ = 1,76 - 2,15 ГПа Борштанги консольные Единичное и мелкосерийное производство Резцы с пластинками ВК8</td></tr>
<tr><td colspan="23">Карта 7</td><td colspan="5">Лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td>Глубина</td><td colspan="20">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемого отверстия D, мм, до</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td colspan="2">500</td><td>600</td><td colspan="2">750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="20">Время на проход, мин.</td></tr>
<tr><td>32</td><td rowspan="4">10</td><td rowspan="4">380</td><td>3</td><td>1,60</td><td>2,4</td><td>3,20</td><td>4,00</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,5</td><td>12,0</td><td>13,5</td><td>15,0</td><td colspan="2">17,0</td><td>19,5</td><td colspan="2">23,5</td><td colspan="2">3,25</td><td>0,70</td><td rowspan="4">48</td><td rowspan="4">57</td><td>1,7</td></tr>
<tr><td>33</td><td>5</td><td>1,80</td><td>2,8</td><td>3,85</td><td>4,85</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,5</td><td>15,0</td><td>17,0</td><td>19,0</td><td colspan="2">21,0</td><td>24,0</td><td colspan="2">29,0</td><td colspan="2">4,05</td><td>0,56</td><td>2,4</td></tr>
<tr><td>34</td><td>8</td><td>2,05</td><td>3,3</td><td>4,55</td><td>6,00</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,0</td><td>13,0</td><td>15,5</td><td>18,0</td><td>20,5</td><td>23,0</td><td colspan="2">25,5</td><td>29,5</td><td colspan="2">35,5</td><td colspan="2">5,00</td><td>0,45</td><td>2,9</td></tr>
<tr><td>35</td><td>12</td><td>2,50</td><td>4,1</td><td>5,50</td><td>7,50</td><td>9,0</td><td>11,0</td><td>12,5</td><td>14,0</td><td>16,5</td><td>19,5</td><td>23,0</td><td>26,0</td><td>29,5</td><td colspan="2">32,5</td><td>37,5</td><td colspan="2">45,5</td><td colspan="2">6,50</td><td>0,35</td><td>4,1</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td>п</td><td colspan="2">р</td><td colspan="2">с</td><td colspan="4"></td></tr>
<tr><td colspan="28">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="21">Твердости чугуна и Твердость чугуна НВ, ГПа до 2,15</td><td colspan="7">свыше 2,15</td></tr>
<tr><td colspan="21">Продолжительность обработки, мин. -</td><td colspan="7">до 10 свыше 10</td></tr>
<tr><td colspan="21"></td><td colspan="7" rowspan="3">1,1 1,25</td></tr>
<tr><td colspan="18">Коэффициент</td><td colspan="3">1,0</td></tr>
<tr><td colspan="21"></td></tr>
<tr><td colspan="28">Состояния обрабатываемой Состояние обрабатываемой поверхности без корки по корке</td></tr>
<tr><td colspan="28"></td></tr>
<tr><td colspan="18">Коэффициент</td><td colspan="10">1,0 1,2</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="26">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="26">Чугун серый, НВ = 1,76 - 2,15 ГПа Борштанги двухопорные Единичное и мелкосерийное производство Резцы с пластинками ВК8</td></tr>
<tr><td colspan="21">Карта 8</td><td colspan="5">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td>Глубина</td><td colspan="18">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемого отверстия D, мм, до</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="18">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="16">10</td><td rowspan="4">120</td><td>3</td><td>2,35</td><td>2,65</td><td>2,90</td><td>3,15</td><td>3,80</td><td>4,10</td><td>4,35</td><td>4,6</td><td>4,95</td><td>5,5</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,0</td><td>9,5</td><td>10,5</td><td colspan="2">1,00</td><td>0,90</td><td rowspan="4">120</td><td rowspan="4">45</td><td>1,5</td></tr>
<tr><td>2</td><td>5</td><td>2,45</td><td>2,75</td><td>3,10</td><td>3,40</td><td>4,20</td><td>4,50</td><td>4,85</td><td>5,5</td><td>6,00</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,0</td><td>9,5</td><td>11,0</td><td>12,5</td><td colspan="2">1,30</td><td>0,70</td><td>2,0</td></tr>
<tr><td>3</td><td>8</td><td>2,55</td><td>2,95</td><td>3,35</td><td>3,75</td><td>4,60</td><td>5,00</td><td>5,50</td><td>6,0</td><td>6,50</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,0</td><td>13,0</td><td>15,0</td><td colspan="2">1,65</td><td>0,56</td><td>3,0</td></tr>
<tr><td>4</td><td>12</td><td>2,65</td><td>3,15</td><td>3,65</td><td>4,15</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,0</td><td>7,50</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,0</td><td>15,0</td><td>17,5</td><td colspan="2">2,00</td><td>0,45</td><td>3,6</td></tr>
<tr><td>5</td><td rowspan="4">150</td><td>3</td><td>2,40</td><td>2,75</td><td>3,05</td><td>3,35</td><td>4,10</td><td>4,45</td><td>4,75</td><td>5,5</td><td>6,00</td><td>6,5</td><td>7,5</td><td>8,0</td><td>9,0</td><td>9,5</td><td>11,0</td><td>12,5</td><td colspan="2">1,25</td><td>0,90</td><td rowspan="4">96</td><td rowspan="4">45</td><td>1,5</td></tr>
<tr><td>6</td><td>5</td><td>2,50</td><td>2,90</td><td>3,30</td><td>3,75</td><td>4,55</td><td>5,00</td><td>5,50</td><td>6,0</td><td>6,50</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,0</td><td>13,0</td><td>15,0</td><td colspan="2">1,65</td><td>0,70</td><td>2,0</td></tr>
<tr><td>7</td><td>8</td><td>2,60</td><td>3,10</td><td>3,60</td><td>4,15</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,0</td><td>7,50</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,0</td><td>15,0</td><td>17,5</td><td colspan="2">2,05</td><td>0,56</td><td>3,0</td></tr>
<tr><td>8</td><td>12</td><td>2,75</td><td>3,40</td><td>4,05</td><td>4,65</td><td>6,00</td><td>6,50</td><td>7,00</td><td>8,0</td><td>9,00</td><td>10,0</td><td>12,0</td><td>13,0</td><td>14,5</td><td>15,5</td><td>18,0</td><td>21,0</td><td colspan="2">2,50</td><td>0,45</td><td>3,6</td></tr>
<tr><td>9</td><td rowspan="4">190</td><td>3</td><td>2,45</td><td>2,90</td><td>3,30</td><td>3,70</td><td>4,55</td><td>4,95</td><td>5,50</td><td>6,0</td><td>6,50</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,0</td><td>13,0</td><td>15,0</td><td colspan="2">1,60</td><td>0,90</td><td rowspan="4">75</td><td rowspan="4">45</td><td>1,5</td></tr>
<tr><td>10</td><td>5</td><td>2,60</td><td>3,10</td><td>3,65</td><td>4,15</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,0</td><td>7,50</td><td>9,0</td><td>10,5</td><td>11,5</td><td>12,5</td><td>13,5</td><td>15,5</td><td>18,0</td><td colspan="2">2,10</td><td>0,70</td><td>2,0</td></tr>
<tr><td>11</td><td>8</td><td>2,70</td><td>3,40</td><td>4,05</td><td>4,70</td><td>6,00</td><td>6,50</td><td>7,50</td><td>8,0</td><td>9,00</td><td>10,0</td><td>12,0</td><td>13,5</td><td>14,5</td><td>16,0</td><td>18,5</td><td>21,5</td><td colspan="2">2,60</td><td>0,56</td><td>3,0</td></tr>
<tr><td>12</td><td>12</td><td>2,90</td><td>3,70</td><td>4,50</td><td>5,50</td><td>7,00</td><td>7,50</td><td>8,50</td><td>9,0</td><td>10,50</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,5</td><td>19,0</td><td>22,0</td><td>26,0</td><td colspan="2">3,25</td><td>0,45</td><td>3,6</td></tr>
<tr><td>13</td><td rowspan="4">210</td><td>3</td><td>2,55</td><td>3,05</td><td>3,55</td><td>4,05</td><td>5,00</td><td>5,50</td><td>6,00</td><td>6,5</td><td>7,50</td><td>8,5</td><td>10,9</td><td>11,0</td><td>12,0</td><td>13,0</td><td>15,0</td><td>17,5</td><td colspan="2">2,00</td><td>0,90</td><td rowspan="4">60</td><td rowspan="4">45</td><td>1,5</td></tr>
<tr><td>14</td><td>5</td><td>2,65</td><td>3,30</td><td>3,95</td><td>4,65</td><td>6,00</td><td>6,50</td><td>7,00</td><td>8,0</td><td>9,00</td><td>10,0</td><td>12,0</td><td>13,0</td><td>14,5</td><td>16,0</td><td>18,0</td><td>21,5</td><td colspan="2">2,60</td><td>0,70</td><td>2,0</td></tr>
<tr><td>15</td><td>8</td><td>2,85</td><td>3,65</td><td>4,45</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,50</td><td>9,0</td><td>10,5</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td>19,0</td><td>21,5</td><td>25,5</td><td colspan="2">3,25</td><td>0,56</td><td>3,0</td></tr>
<tr><td>16</td><td>12</td><td>3,10</td><td>4,10</td><td>5,50</td><td>6,50</td><td>8,00</td><td>9,00</td><td>10,0</td><td>11,0</td><td>12,5</td><td>14,5</td><td>17,0</td><td>19,0</td><td>21,0</td><td>23,0</td><td>26,5</td><td>31,5</td><td colspan="2">4,05</td><td>0,45</td><td>3,6</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td colspan="2">с</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="28">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="28">Чугун серый, НВ = 1,76 - 2,15 ГПа Борштанги двухопорные Единичное и мелкосерийное производство Резцы с пластинками ВК8</td></tr>
<tr><td colspan="23">Карта 8</td><td colspan="5">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td>Глубина</td><td colspan="20">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемого отверстия D, мм, до</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td colspan="2">500</td><td>600</td><td colspan="2">750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="20">Время на проход, мин.</td></tr>
<tr><td>17</td><td rowspan="12">10</td><td rowspan="4">300</td><td>3</td><td>2,60</td><td>3,25</td><td>3,9</td><td>4,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,0</td><td>14,0</td><td colspan="2">15,5</td><td>18,0</td><td colspan="2">21,0</td><td colspan="2">2,52</td><td>0,90</td><td rowspan="4">48</td><td rowspan="4">45</td><td>1,5</td></tr>
<tr><td>18</td><td>5</td><td>2,80</td><td>3,60</td><td>4,4</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,0</td><td>10,5</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td colspan="2">19,0</td><td>21,5</td><td colspan="2">25,5</td><td colspan="2">3,25</td><td>0,70</td><td>2,0</td></tr>
<tr><td>19</td><td>8</td><td>3,00</td><td>4,00</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,5</td><td>14,5</td><td>17,0</td><td>19,0</td><td>21,0</td><td colspan="2">23,0</td><td>26,5</td><td colspan="2">31,5</td><td colspan="2">4,05</td><td>0,56</td><td>3,0</td></tr>
<tr><td>20</td><td>12</td><td>3,30</td><td>4,55</td><td>6,0</td><td>7,0</td><td>9,0</td><td>10,0</td><td>11,5</td><td>12,5</td><td>14,5</td><td>17,0</td><td>20,0</td><td>22,5</td><td>25,0</td><td colspan="2">27,5</td><td>31,5</td><td colspan="2">38,0</td><td colspan="2">5,00</td><td>0,45</td><td>3,6</td></tr>
<tr><td>21</td><td rowspan="4">380</td><td>3</td><td>2,70</td><td>3,50</td><td>4,3</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,0</td><td>9,0</td><td>10,0</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td colspan="2">18,5</td><td>21,5</td><td colspan="2">25,5</td><td colspan="2">3,20</td><td>0,90</td><td rowspan="4">38</td><td rowspan="4">45</td><td>1,5</td></tr>
<tr><td>22</td><td>5</td><td>2,90</td><td>3,95</td><td>4,95</td><td>6,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>12,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td>21,0</td><td colspan="2">23,0</td><td>26,5</td><td colspan="2">31,5</td><td colspan="2">4,10</td><td>0,70</td><td>2,0</td></tr>
<tr><td>23</td><td>8</td><td>3,25</td><td>4,55</td><td>6,00</td><td>7,5</td><td>9,0</td><td>10,5</td><td>11,5</td><td>13,0</td><td>15,0</td><td>17,5</td><td>20,5</td><td>23,0</td><td>26,0</td><td colspan="2">28,5</td><td>33,0</td><td colspan="2">39,5</td><td colspan="2">5,00</td><td>0,56</td><td>3,0</td></tr>
<tr><td>24</td><td>12</td><td>3,60</td><td>5,50</td><td>7,00</td><td>8,5</td><td>10,5</td><td>12,5</td><td>14,0</td><td>15,5</td><td>18,0</td><td>21,0</td><td>25,0</td><td>28,0</td><td>31,5</td><td colspan="2">34,5</td><td>40,0</td><td colspan="2">48,0</td><td colspan="2">6,50</td><td>0,45</td><td>3,6</td></tr>
<tr><td>25</td><td rowspan="4">480</td><td>3</td><td>2,85</td><td>3,85</td><td>4,85</td><td>6,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td>20,5</td><td colspan="2">22,5</td><td>26,0</td><td colspan="2">31,5</td><td colspan="2">4,05</td><td>0,90</td><td rowspan="4">30</td><td rowspan="4">45</td><td>1,5</td></tr>
<tr><td>26</td><td>5</td><td>3,15</td><td>4,45</td><td>6,0</td><td>7,5</td><td>9,0</td><td>10,5</td><td>11,5</td><td>13,0</td><td>15,0</td><td>17,5</td><td>20,5</td><td>23,0</td><td>25,5</td><td colspan="2">28,5</td><td>32,5</td><td colspan="2">39,0</td><td colspan="2">5,00</td><td>0,70</td><td>2,0</td></tr>
<tr><td>27</td><td>8</td><td>3,45</td><td>5,50</td><td>7,0</td><td>8,5</td><td>10,5</td><td>12,0</td><td>14,0</td><td>15,5</td><td>18,0</td><td>21,0</td><td>24,5</td><td>28,0</td><td>31,0</td><td colspan="2">34,5</td><td>39,5</td><td colspan="2">47,5</td><td colspan="2">6,50</td><td>0,56</td><td>3,0</td></tr>
<tr><td>28</td><td>12</td><td>4,05</td><td>6,50</td><td>8,5</td><td>10,5</td><td>13,0</td><td>15,0</td><td>17,5</td><td>19,5</td><td>22,5</td><td>27,0</td><td>31,5</td><td>35,5</td><td>40,0</td><td colspan="2">44,0</td><td>51,0</td><td colspan="2">62,0</td><td colspan="2">8,00</td><td>0,45</td><td>3,6</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td>п</td><td colspan="2">р</td><td colspan="2">с</td><td></td><td></td><td></td><td></td></tr>
<tr><td colspan="28">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="21">Твердости чугуна и Твердость чугуна НВ, ГПа до 2,15</td><td colspan="7">свыше 2,15</td></tr>
<tr><td colspan="21">Продолжительность обработки, мин. -</td><td colspan="7">до 10 свыше 10</td></tr>
<tr><td colspan="21"></td><td colspan="7" rowspan="3">1,1 1,25</td></tr>
<tr><td colspan="18">Коэффициент</td><td colspan="3">1,0</td></tr>
<tr><td colspan="21"></td></tr>
<tr><td colspan="28">Состояния обрабатываемой Состояние обрабатываемой поверхности без корки по корке</td></tr>
<tr><td colspan="28"></td></tr>
<tr><td colspan="18">Коэффициент</td><td colspan="10">1,0 1,2</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="27">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 20, 1Т9 квалитет</td></tr>
<tr><td colspan="27">Чугун серый, НВ = 1,76 - 2,15 ГПа Резцы с пластинками ВК8 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="27">Карта 9</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td>Глубина</td><td colspan="19">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемого отверстия D, мм, до</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td colspan="2">500</td><td>600</td><td colspan="2">750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="19">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">10</td><td>30</td><td rowspan="12">1</td><td>3,40</td><td>3,50</td><td>3,6</td><td>3,75</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>-</td><td>0,25</td><td>750</td><td>70</td><td rowspan="12">1</td></tr>
<tr><td>2</td><td>45</td><td>3,40</td><td>3,50</td><td>3,65</td><td>3,75</td><td>4,25</td><td>4,4</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>-</td><td rowspan="11">0,45</td><td>480</td><td rowspan="11">57</td></tr>
<tr><td>3</td><td>60</td><td>3,40</td><td>3,55</td><td>3,75</td><td>3,90</td><td>4,45</td><td>4,6</td><td>4,75</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>-</td><td>350</td></tr>
<tr><td>4</td><td>75</td><td>3,45</td><td>3,70</td><td>3,95</td><td>4,20</td><td>4,85</td><td>5,5</td><td>5,50</td><td>6,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>-</td><td>300</td></tr>
<tr><td>5</td><td>96</td><td>3,45</td><td>3,70</td><td>3,95</td><td>4,20</td><td>4,85</td><td>5,5</td><td>5,50</td><td>6,0</td><td>6,0</td><td>6,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>-</td><td>240</td></tr>
<tr><td>6</td><td>120</td><td>3,50</td><td>3,80</td><td>4,15</td><td>4,45</td><td>5,50</td><td>5,5</td><td>6,00</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>-</td><td>100</td></tr>
<tr><td>7</td><td>150</td><td>3,55</td><td>3,95</td><td>4,35</td><td>4,75</td><td>6,00</td><td>6,0</td><td>6,50</td><td>7,0</td><td>7,5</td><td>8,5</td><td>10,0</td><td>10,5</td><td>11,5</td><td colspan="2">12,5</td><td>14,5</td><td colspan="2">16,5</td><td>2,00</td><td>150</td></tr>
<tr><td>8</td><td>190</td><td>3,60</td><td>4,10</td><td>4,60</td><td>5,50</td><td>6,00</td><td>6,5</td><td>7,50</td><td>8,0</td><td>8,5</td><td>9,5</td><td>11,0</td><td>12,0</td><td>13,0</td><td colspan="2">14,0</td><td>16,5</td><td colspan="2">19,0</td><td>2,50</td><td>120</td></tr>
<tr><td>9</td><td>240</td><td>3,70</td><td>4,30</td><td>4,95</td><td>6,00</td><td>7,00</td><td>7,5</td><td>8,00</td><td>8,5</td><td>9,5</td><td>11,0</td><td>13,0</td><td>14,0</td><td>15,5</td><td colspan="2">16,5</td><td>19,5</td><td colspan="2">22,5</td><td>3,25</td><td>96</td></tr>
<tr><td>10</td><td>300</td><td>3,80</td><td>4,60</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,5</td><td>9,00</td><td>10,0</td><td>11,0</td><td>13,0</td><td>15,0</td><td>16,5</td><td>18,5</td><td colspan="2">20,0</td><td>23,0</td><td colspan="2">27,0</td><td>4,05</td><td>76</td></tr>
<tr><td>11</td><td>380</td><td>3,90</td><td>4,90</td><td>6,00</td><td>7,00</td><td>8,50</td><td>9,5</td><td>10,5</td><td>11,5</td><td>13,0</td><td>15,0</td><td>18,0</td><td>20,0</td><td>22,0</td><td colspan="2">24,0</td><td>27,5</td><td colspan="2">32,5</td><td>5,00</td><td>60</td></tr>
<tr><td>12</td><td>480</td><td>4,05</td><td>5,50</td><td>6,50</td><td>8,00</td><td>9,50</td><td>11,0</td><td>12,0</td><td>13,5</td><td>15,0</td><td>17,5</td><td>21,0</td><td>23,5</td><td>26,0</td><td colspan="2">28,5</td><td>33,0</td><td colspan="2">39,0</td><td>6,50</td><td>48</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td>п</td><td colspan="2">р</td><td>с</td><td></td><td></td><td></td><td></td></tr>
<tr><td colspan="27">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="21">Твердости чугуна и Твердость чугуна НВ, ГПа до 2,15</td><td colspan="6">свыше 2,15</td></tr>
<tr><td colspan="21">Продолжительность обработки, мин. -</td><td colspan="6">до 10 свыше 10</td></tr>
<tr><td colspan="21"></td><td colspan="6" rowspan="3">1,1 1,25</td></tr>
<tr><td colspan="18">Коэффициент</td><td colspan="3">1,0</td></tr>
</table>


<a id="p100667"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету время по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="27">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 2,5, 1Т9 - 1Т8 квалитет</td></tr>
<tr><td colspan="27">Чугун серый, НВ = 1,76 - 2,15 ГПа Резцы с пластинками ВК6 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="27">Карта 10</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td>Глубина</td><td colspan="19">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемого отверстия D, мм, до</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td colspan="2">500</td><td>600</td><td colspan="2">750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="19">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">10</td><td>30</td><td rowspan="12">1</td><td>3,30</td><td>3,45</td><td>3,65</td><td>3,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>0,66</td><td rowspan="12">0,22</td><td>750</td><td rowspan="12">90</td><td rowspan="12">1</td></tr>
<tr><td>2</td><td>48</td><td>3,35</td><td>3,55</td><td>3,75</td><td>3,95</td><td>4,65</td><td>4,85</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>0,82</td><td>600</td></tr>
<tr><td>3</td><td>60</td><td>3,40</td><td>3,60</td><td>3,85</td><td>4,15</td><td>4,9</td><td>5,0</td><td>5,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>1,05</td><td>480</td></tr>
<tr><td>4</td><td>75</td><td>3,45</td><td>3,70</td><td>4,05</td><td>4,4</td><td>5,2</td><td>5,5</td><td>6,0</td><td>6,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>1,30</td><td>380</td></tr>
<tr><td>5</td><td>96</td><td>3,50</td><td>3,85</td><td>4,30</td><td>4,7</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>1,65</td><td>300</td></tr>
<tr><td>6</td><td>120</td><td>4,05</td><td>4,55</td><td>5,00</td><td>5,5</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,0</td><td>9,0</td><td>10,0</td><td>11,5</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>2,10</td><td>240</td></tr>
<tr><td>7</td><td>150</td><td>4,20</td><td>4,75</td><td>5,50</td><td>6,0</td><td>7,0</td><td>8,0</td><td>8,5</td><td>9,0</td><td>10,0</td><td>11,5</td><td>13,5</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>2,65</td><td>190</td></tr>
<tr><td>8</td><td>190</td><td>4,30</td><td>5,00</td><td>6,00</td><td>6,5</td><td>8,0</td><td>9,0</td><td>9,5</td><td>10,5</td><td>11,5</td><td>13,5</td><td>16,0</td><td>17,5</td><td>19,0</td><td colspan="2">21,0</td><td>25,0</td><td colspan="2">30,0</td><td>3,35</td><td>150</td></tr>
<tr><td>9</td><td>240</td><td>4,45</td><td>5,50</td><td>6,50</td><td>7,5</td><td>9,0</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,5</td><td>15,5</td><td>18,5</td><td>20,5</td><td>22,5</td><td colspan="2">24,5</td><td>30,0</td><td colspan="2">35,5</td><td>4,15</td><td>120</td></tr>
<tr><td>10</td><td>300</td><td>5,50</td><td>7,00</td><td>8,00</td><td>9,5</td><td>11,5</td><td>13,0</td><td>14,0</td><td>15,5</td><td>17,5</td><td>20,0</td><td>23,5</td><td>26,0</td><td>28,5</td><td colspan="2">31,0</td><td>37,5</td><td colspan="2">45,0</td><td>5,00</td><td>96</td></tr>
<tr><td>11</td><td>380</td><td>6,00</td><td>7,50</td><td>9,00</td><td>11,0</td><td>13,0</td><td>15,0</td><td>16,5</td><td>18,0</td><td>20,5</td><td>24,0</td><td>28,0</td><td>31,5</td><td>35,0</td><td colspan="2">38,0</td><td>45,5</td><td colspan="2">55,0</td><td>6,50</td><td>75</td></tr>
<tr><td>12</td><td>480</td><td>6,50</td><td>8,00</td><td>10,0</td><td>12,5</td><td>15,0</td><td>17,0</td><td>19,0</td><td>21,5</td><td>24,5</td><td>28,5</td><td>33,5</td><td>37,5</td><td>42,0</td><td colspan="2">46,0</td><td>55,0</td><td colspan="2">67,0</td><td>8,50</td><td>60</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td>п</td><td colspan="2">р</td><td>с</td><td></td><td></td><td></td><td></td></tr>
<tr><td colspan="27">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="21">Твердости чугуна и Твердость чугуна НВ, ГПа до 2,15</td><td colspan="6">свыше 2,15</td></tr>
<tr><td colspan="21">Продолжительность обработки, мин. -</td><td colspan="6">до 10 свыше 10</td></tr>
<tr><td colspan="21"></td><td colspan="6" rowspan="3">1,1 1,25</td></tr>
<tr><td colspan="18">Коэффициент</td><td colspan="3">1,0</td></tr>
</table>


<a id="p100689"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету время по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="3%"><col width="7%"><col width="4%"><col width="3%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="3%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="3%"></colgroup>
<tr><td colspan="20">Неполное штучное время Растачивание отверстий, Ra 1,25, 1Т7 квалитет</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="20" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="8">Резцы с пластинками ВК6</td></tr>
<tr><td colspan="8">Карта 11</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="20">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td colspan="2">100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td colspan="2">750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>до</td><td colspan="20">Время на проход, мин.</td></tr>
<tr><td>1</td><td>30</td><td rowspan="12">1</td><td>5,3</td><td>5,5</td><td>5,8</td><td colspan="2">6,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td rowspan="12">0,12</td><td colspan="2">960</td><td rowspan="12">113</td><td rowspan="12">1</td></tr>
<tr><td>2</td><td>48</td><td>5,5</td><td>6,0</td><td>6,0</td><td colspan="2">6,5</td><td>7,0</td><td>7,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">750</td></tr>
<tr><td>3</td><td>60</td><td>5,5</td><td>6,0</td><td>6,5</td><td colspan="2">6,5</td><td>7,5</td><td>8,0</td><td>8,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">600</td></tr>
<tr><td>4</td><td>75</td><td>5,5</td><td>6,0</td><td>6,5</td><td colspan="2">7,0</td><td>8,0</td><td>8,5</td><td>9,0</td><td>9,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">480</td></tr>
<tr><td>5</td><td>96</td><td>5,5</td><td>6,0</td><td>6,5</td><td colspan="2">7,5</td><td>8,5</td><td>9,0</td><td>10,0</td><td>10,5</td><td>11,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td colspan="2">380</td></tr>
<tr><td>6</td><td>120</td><td>6,0</td><td>7,0</td><td>7,5</td><td colspan="2">8,5</td><td>10,0</td><td>10,5</td><td>11,5</td><td>12,0</td><td>13,5</td><td>15</td><td>17,0</td><td>18,5</td><td>20,0</td><td>22</td><td>26</td><td colspan="2">29</td><td colspan="2">3,0</td><td colspan="2">300</td></tr>
<tr><td>7</td><td>150</td><td>6,5</td><td>7,0</td><td>8,0</td><td colspan="2">9,0</td><td>10,5</td><td>12,0</td><td>13,0</td><td>14,0</td><td>15,0</td><td>17</td><td>19,5</td><td>21,5</td><td>23,5</td><td>25</td><td>30</td><td colspan="2">35</td><td colspan="2">3,8</td><td colspan="2">240</td></tr>
<tr><td>8</td><td>190</td><td>6,5</td><td>7,5</td><td>9,0</td><td colspan="2">10,0</td><td>12,0</td><td>13,0</td><td>14,0</td><td>15,5</td><td>17,5</td><td>20</td><td>23,0</td><td>25,5</td><td>28,0</td><td>30</td><td>36</td><td colspan="2">41</td><td colspan="2">4,8</td><td colspan="2">190</td></tr>
<tr><td>9</td><td>240</td><td>7,0</td><td>8,0</td><td>9,5</td><td colspan="2">11,0</td><td>13,5</td><td>15,0</td><td>16,5</td><td>18,0</td><td>20,0</td><td>23</td><td>27,0</td><td>30,0</td><td>33,0</td><td>36</td><td>44</td><td colspan="2">50</td><td colspan="2">6,0</td><td colspan="2">150</td></tr>
<tr><td>10</td><td>300</td><td>7,5</td><td>9,5</td><td>11,0</td><td colspan="2">13,0</td><td>16,0</td><td>18,0</td><td>19,5</td><td>21,5</td><td>24,5</td><td>28</td><td>33,0</td><td>36,0</td><td>40,0</td><td>44</td><td>53</td><td colspan="2">61</td><td colspan="2">7,6</td><td colspan="2">120</td></tr>
<tr><td>11</td><td>380</td><td>8,0</td><td>10,0</td><td>12,5</td><td colspan="2">15,0</td><td>18,0</td><td>20,5</td><td>23,0</td><td>26,0</td><td>29,0</td><td>33</td><td>39,0</td><td>43,0</td><td>48,0</td><td>53</td><td>64</td><td colspan="2">74</td><td colspan="2">9,5</td><td colspan="2">96</td></tr>
<tr><td>12</td><td>480</td><td>8,5</td><td>11,5</td><td>14,5</td><td colspan="2">17,5</td><td>21,0</td><td>24,0</td><td>27,0</td><td>30,0</td><td>35,0</td><td>41</td><td>47,0</td><td>54,0</td><td>60,0</td><td>66</td><td>80</td><td colspan="2">92</td><td colspan="2">12,2</td><td colspan="2">75</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td colspan="2">р</td><td colspan="2">с</td><td></td><td colspan="2"></td><td></td><td></td></tr>
<tr><td colspan="28">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="7" rowspan="3">Твердости чугуна и продолжительности обработки</td><td colspan="11">Твердость чугуна НВ, ГПа</td><td colspan="4">до 2,15</td><td colspan="6">свыше 2,15</td></tr>
<tr><td colspan="11">Продолжительность обработки, мин.</td><td colspan="4">-</td><td colspan="3">до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td colspan="11">Коэффициент</td><td colspan="4">1,0</td><td colspan="3">1,1</td><td colspan="3">1,25</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="6%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="10%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="19">Неполное штучное время Горизонтально-расточные станки Продольное и поперечное точение, Rz 90, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="19">Чугун серый, НВ = 1,76 - 2,15 ГПа Суппорт планшайбы Единичное и мелкосерийное производство Резцы с пластинками ВК8</td></tr>
<tr><td colspan="15">Карта 12</td><td colspan="4">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемой поверхности D, мм, до</td><td>Глубина</td><td colspan="10">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>Добавлять на каждые 100 мм свыше 250</td><td colspan="2" rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="10">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="13">10</td><td rowspan="3">120</td><td>3</td><td>1,40</td><td>1,65</td><td>2,15</td><td>2,40</td><td>2,85</td><td>3,15</td><td>3,40</td><td>3,65</td><td>4,35</td><td>1,05</td><td colspan="2">0,70</td><td rowspan="3">150</td><td rowspan="12">57</td><td>1,5</td></tr>
<tr><td>2</td><td>5</td><td>1,45</td><td>1,80</td><td>2,35</td><td>2,65</td><td>3,20</td><td>3,55</td><td>3,85</td><td>4,20</td><td>5,00</td><td>1,30</td><td colspan="2">0,56</td><td>2,2</td></tr>
<tr><td>3</td><td>8</td><td>1,55</td><td>1,95</td><td>2,60</td><td>3,00</td><td>3,60</td><td>4,05</td><td>4,45</td><td>4,85</td><td>6,00</td><td>1,60</td><td colspan="2">0,45</td><td>3,2</td></tr>
<tr><td>4</td><td rowspan="3">150</td><td>3</td><td>1,45</td><td>1,75</td><td>2,30</td><td>2,65</td><td>3,15</td><td>3,50</td><td>3,80</td><td>4,15</td><td>4,95</td><td>1,30</td><td colspan="2">0,70</td><td rowspan="3">120</td><td>1,5</td></tr>
<tr><td>5</td><td>5</td><td>1,50</td><td>1,90</td><td>2,55</td><td>2,95</td><td>3,60</td><td>4,00</td><td>4,40</td><td>4,80</td><td>6,00</td><td>1,65</td><td colspan="2">0,56</td><td>2,2</td></tr>
<tr><td>6</td><td>8</td><td>1,60</td><td>2,15</td><td>2,85</td><td>3,35</td><td>4,10</td><td>4,60</td><td>5,50</td><td>6,00</td><td>7,00</td><td>2,05</td><td colspan="2">0,45</td><td>3,2</td></tr>
<tr><td>7</td><td rowspan="3">190</td><td>3</td><td>1,50</td><td>1,90</td><td>2,50</td><td>2,95</td><td>3,55</td><td>3,95</td><td>4,35</td><td>4,80</td><td>6,00</td><td>1,65</td><td colspan="2">0,70</td><td rowspan="3">96</td><td>1,5</td></tr>
<tr><td>8</td><td>5</td><td>1,60</td><td>2,10</td><td>2,80</td><td>3,30</td><td>4,05</td><td>4,55</td><td>5,50</td><td>6,00</td><td>7,00</td><td>2,05</td><td colspan="2">0,56</td><td>2,2</td></tr>
<tr><td>9</td><td>8</td><td>1,75</td><td>2,35</td><td>3,20</td><td>3,85</td><td>4,70</td><td>5,50</td><td>6,00</td><td>7,00</td><td>8,00</td><td>2,55</td><td colspan="2">0,45</td><td>3,2</td></tr>
<tr><td>10</td><td rowspan="3">240</td><td>3</td><td>1,55</td><td>2,10</td><td>2,85</td><td>3,35</td><td>4,10</td><td>4,65</td><td>5,50</td><td>6,00</td><td>7,00</td><td>2,10</td><td colspan="2">0,70</td><td rowspan="3">75</td><td>1,5</td></tr>
<tr><td>11</td><td>5</td><td>1,70</td><td>2,35</td><td>3,20</td><td>3,85</td><td>4,15</td><td>5,50</td><td>6,50</td><td>7,00</td><td>8,00</td><td>2,60</td><td colspan="2">0,56</td><td>2,2</td></tr>
<tr><td>12</td><td>8</td><td>1,85</td><td>2,65</td><td>3,70</td><td>4,50</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,00</td><td>9,50</td><td>3,25</td><td colspan="2">0,45</td><td>3,2</td></tr>
<tr><td>13</td><td>300</td><td>3</td><td>1,65</td><td>2,30</td><td>3,15</td><td>3,80</td><td>4,70</td><td>5,50</td><td>6,00</td><td>7,00</td><td>8,00</td><td>2,60</td><td colspan="2">0,70</td><td>60</td><td></td><td>1,5</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="6%"><col width="8%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="2%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="3%"><col width="2%"><col width="2%"><col width="3%"><col width="10%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="24">Неполное штучное время Горизонтально-расточные станки Продольное и поперечное точение, Rz 90, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="24">Чугун серый, НВ = 1,76 - 2,15 ГПа Суппорт планшайбы Единичное и мелкосерийное производство Резцы с пластинками ВК8</td></tr>
<tr><td colspan="20">Карта 12</td><td colspan="4">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="2">Диаметр обрабатываемой поверхности D, мм,</td><td>Глубина</td><td colspan="15">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td colspan="2">50</td><td colspan="2">75</td><td>100</td><td>125</td><td>150</td><td colspan="2">175</td><td colspan="2">200</td><td colspan="2">250</td><td>Добавлять на каждые 100 мм свыше 250</td><td colspan="2" rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td>до</td><td colspan="15">Время на проход, мин.</td></tr>
<tr><td>14</td><td rowspan="11">10</td><td rowspan="2">300</td><td>5</td><td>1,80</td><td colspan="2">2,60</td><td colspan="2">3,60</td><td>4,45</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">8,0</td><td colspan="2">9,5</td><td>3,25</td><td colspan="2">0,56</td><td rowspan="2">60</td><td rowspan="11">57</td><td>2,2</td></tr>
<tr><td>15</td><td>8</td><td>2,00</td><td colspan="2">3,05</td><td colspan="2">4,25</td><td>5,50</td><td>6,5</td><td>8,0</td><td colspan="2">9,0</td><td colspan="2">10,0</td><td colspan="2">11,5</td><td>4,05</td><td colspan="2">0,45</td><td>3,2</td></tr>
<tr><td>16</td><td rowspan="3">380</td><td>3</td><td>1,75</td><td colspan="2">2,55</td><td colspan="2">3,00</td><td>4,45</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">8,0</td><td colspan="2">10,0</td><td>3,25</td><td colspan="2">0,70</td><td rowspan="3">48</td><td>1,5</td></tr>
<tr><td>17</td><td>5</td><td>1,95</td><td colspan="2">2,95</td><td colspan="2">4,20</td><td>5,50</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td colspan="2">9,5</td><td colspan="2">11,5</td><td>4,05</td><td colspan="2">0,56</td><td>2,2</td></tr>
<tr><td>18</td><td>8</td><td>2,25</td><td colspan="2">3,55</td><td colspan="2">5,50</td><td>6,50</td><td>8,0</td><td>9,5</td><td colspan="2">10,5</td><td colspan="2">12,0</td><td colspan="2">14,5</td><td>5,00</td><td colspan="2">0,45</td><td>3,2</td></tr>
<tr><td>19</td><td rowspan="3">480</td><td>3</td><td>1,90</td><td colspan="2">2,95</td><td colspan="2">4,20</td><td>5,50</td><td>7,0</td><td>8,0</td><td colspan="2">9,0</td><td colspan="2">10,0</td><td colspan="2">12,0</td><td>4,00</td><td colspan="2">0,70</td><td rowspan="3">38</td><td>1,5</td></tr>
<tr><td>20</td><td>5</td><td>2,15</td><td colspan="2">3,45</td><td colspan="2">4,95</td><td>6,50</td><td>8,0</td><td>9,5</td><td colspan="2">10,5</td><td colspan="2">12,0</td><td colspan="2">14,0</td><td>5,00</td><td colspan="2">0,56</td><td>2,2</td></tr>
<tr><td>21</td><td>8</td><td>2,50</td><td colspan="2">4,10</td><td colspan="2">6,00</td><td>8,00</td><td>9,5</td><td>11,0</td><td colspan="2">13,0</td><td colspan="2">14,5</td><td colspan="2">17,0</td><td>6,50</td><td colspan="2">0,45</td><td>3,2</td></tr>
<tr><td>22</td><td rowspan="3">600</td><td>3</td><td>2,05</td><td colspan="2">3,35</td><td colspan="2">4,85</td><td>6,50</td><td>8,0</td><td>9,0</td><td colspan="2">10,5</td><td colspan="2">12,0</td><td colspan="2">14,0</td><td>5,00</td><td colspan="2">0,70</td><td rowspan="3">30</td><td>1,5</td></tr>
<tr><td>23</td><td>5</td><td>2,35</td><td colspan="2">3,95</td><td colspan="2">6,00</td><td>7,50</td><td>9,5</td><td>11,0</td><td colspan="2">12,5</td><td colspan="2">14,5</td><td colspan="2">17,0</td><td>6,50</td><td colspan="2">0,56</td><td>2,2</td></tr>
<tr><td>24</td><td>8</td><td>2,85</td><td colspan="2">5,00</td><td colspan="2">7,50</td><td>9,50</td><td>12,0</td><td>14,0</td><td colspan="2">16,0</td><td colspan="2">18,5</td><td colspan="2">22,0</td><td>8,00</td><td colspan="2">0,45</td><td>3,2</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td colspan="2">б</td><td colspan="2">в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td colspan="2">з</td><td colspan="2">и</td><td>к</td><td colspan="2"></td><td></td><td></td><td></td></tr>
<tr><td colspan="24">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6" rowspan="5">Твердости чугуна и продолжительности обработки</td><td colspan="18">Твердость чугуна НВ, ГПа до 2,15 свыше 2,15</td></tr>
<tr><td colspan="18">Продолжительность обработки, мин. - до 10 свыше 10</td></tr>
<tr><td colspan="18"></td></tr>
<tr><td colspan="11">Коэффициент</td><td colspan="7">1,0 1,1 1,25</td></tr>
<tr><td colspan="18"></td></tr>
<tr><td colspan="6" rowspan="5">Вида обработки</td><td colspan="18">Продольное и поперечное точение Растачивание</td></tr>
<tr><td colspan="18">Коэффициент</td></tr>
<tr><td colspan="18"></td></tr>
<tr><td colspan="2">1,0</td><td colspan="16">1,06</td></tr>
<tr><td colspan="18"></td></tr>
<tr><td colspan="6" rowspan="4">Состояния обрабатываемой поверхности</td><td colspan="7">Состояние обрабатываемой поверхности</td><td colspan="11">без корки по корке</td></tr>
<tr><td colspan="7" rowspan="3">Коэффициент</td><td colspan="11"></td></tr>
<tr><td colspan="2">1,0</td><td colspan="9">1,2</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="6%"><col width="8%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="2%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="5%"><col width="2%"><col width="3%"><col width="10%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="21">Неполное штучное время Горизонтально-расточные станки Продольное и поперечное точение, Rz 40, 1Т11 квалитет</td></tr>
<tr><td colspan="21">Чугун серый, НВ = 1,76 - 2,15 ГПа Суппорт планшайбы Единичное и мелкосерийное производство Резцы с пластинками ВК6</td></tr>
<tr><td colspan="21">Карта 13</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="2">Диаметр обрабатываемой поверхности D, мм,</td><td>Глубина</td><td colspan="13">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td colspan="2">50</td><td colspan="2">75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td colspan="2">250</td><td>Добавлять на каждые 100 мм свыше 250</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td>до</td><td colspan="13">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="8">10</td><td>120</td><td rowspan="8">1</td><td>1,70</td><td colspan="2">1,95</td><td colspan="2">2,30</td><td>2,55</td><td>3,05</td><td>3,30</td><td>3,55</td><td>3,8</td><td colspan="2">4,5</td><td>1,00</td><td rowspan="8">0,45</td><td>240</td><td rowspan="8">90</td><td rowspan="8">1,0</td></tr>
<tr><td>2</td><td>150</td><td>1,75</td><td colspan="2">2,05</td><td colspan="2">2,50</td><td>2,80</td><td>3,35</td><td>3,70</td><td>4,00</td><td>5,0</td><td colspan="2">5,5</td><td>1,30</td><td>190</td></tr>
<tr><td>3</td><td>190</td><td>1,80</td><td colspan="2">2,20</td><td colspan="2">2,70</td><td>3,15</td><td>3,75</td><td>4,15</td><td>4,55</td><td>5,0</td><td colspan="2">6,0</td><td>1,60</td><td>150</td></tr>
<tr><td>4</td><td>240</td><td>1,85</td><td colspan="2">2,35</td><td colspan="2">3,00</td><td>3,50</td><td>4,20</td><td>4,70</td><td>5,50</td><td>6,0</td><td colspan="2">7,0</td><td>2,05</td><td>120</td></tr>
<tr><td>5</td><td>300</td><td>1,95</td><td colspan="2">2,55</td><td colspan="2">3,30</td><td>3,95</td><td>4,80</td><td>5,50</td><td>6,50</td><td>7,0</td><td colspan="2">8,0</td><td>2,50</td><td>96</td></tr>
<tr><td>6</td><td>380</td><td>2,00</td><td colspan="2">2,85</td><td colspan="2">3,75</td><td>4,55</td><td>6,00</td><td>6,50</td><td>7,50</td><td>8,0</td><td colspan="2">10,0</td><td>3,25</td><td>75</td></tr>
<tr><td>7</td><td>480</td><td>2,15</td><td colspan="2">3,15</td><td colspan="2">4,30</td><td>5,50</td><td>7,00</td><td>8,00</td><td>9,00</td><td>10,0</td><td colspan="2">11,5</td><td>4,05</td><td>60</td></tr>
<tr><td>8</td><td>600</td><td>2,30</td><td colspan="2">3,50</td><td colspan="2">4,90</td><td>6,50</td><td>8,00</td><td>9,00</td><td>10,50</td><td>11,5</td><td colspan="2">13,5</td><td>5,00</td><td>48</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td colspan="2">б</td><td colspan="2">в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td></td><td></td><td></td><td></td></tr>
<tr><td colspan="21">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6" rowspan="5">Твердости чугуна и продолжительности обработки</td><td colspan="15">Твердость чугуна НВ, ГПа до 2,15 свыше 2,15</td></tr>
<tr><td colspan="15">Продолжительность обработки, мин. - до 10 свыше 10</td></tr>
<tr><td colspan="15"></td></tr>
<tr><td colspan="9">Коэффициент</td><td colspan="6">1,0 1,1 1,25</td></tr>
<tr><td colspan="15"></td></tr>
<tr><td colspan="6" rowspan="5">Вида обработки</td><td colspan="15">Продольное и поперечное точение Растачивание</td></tr>
<tr><td colspan="15">Коэффициент</td></tr>
<tr><td colspan="15"></td></tr>
<tr><td colspan="2">1,0</td><td colspan="13">1,06</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="6%"><col width="8%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="2%"><col width="3%"><col width="5%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="3%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="22">Неполное штучное время Горизонтально-расточные станки Продольное и поперечное точение, Ra 2,5, 1Т9 - 1Т8 квалитет</td></tr>
<tr><td colspan="22">Чугун серый, НВ = 1,76 - 2,15 ГПа Суппорт планшайбы Единичное и мелкосерийное производство Резцы с пластинками ВК6</td></tr>
<tr><td colspan="22">Карта 14</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="2">Диаметр обрабатываемой поверхности D, мм,</td><td>Глубина</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td colspan="2">50</td><td colspan="2">75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td colspan="2">250</td><td colspan="2">Добавлять на каждые 100 мм свыше 250</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td>до</td><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="8">10</td><td>120</td><td rowspan="8">1</td><td>2,80</td><td colspan="2">3,05</td><td colspan="2">3,45</td><td>3,70</td><td>4,3</td><td>4,55</td><td>4,8</td><td>5,5</td><td colspan="2">6,0</td><td colspan="2">1,00</td><td rowspan="8">0,22</td><td>480</td><td rowspan="8">180</td><td rowspan="8">1,9</td></tr>
<tr><td>2</td><td>150</td><td>2,85</td><td colspan="2">3,15</td><td colspan="2">3,60</td><td>3,95</td><td>4,6</td><td>4,90</td><td>5,5</td><td>6,0</td><td colspan="2">6,5</td><td colspan="2">1,30</td><td>380</td></tr>
<tr><td>3</td><td>190</td><td>2,90</td><td colspan="2">3,30</td><td colspan="2">3,85</td><td>4,25</td><td>5,0</td><td>5,50</td><td>6,0</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">1,65</td><td>300</td></tr>
<tr><td>4</td><td>240</td><td>2,95</td><td colspan="2">3,45</td><td colspan="2">4,10</td><td>4,60</td><td>5,5</td><td>6,00</td><td>6,5</td><td>7,0</td><td colspan="2">8,0</td><td colspan="2">2,10</td><td>240</td></tr>
<tr><td>5</td><td>300</td><td>3,05</td><td colspan="2">3,70</td><td colspan="2">4,45</td><td>5,50</td><td>6,5</td><td>7,00</td><td>7,5</td><td>8,5</td><td colspan="2">9,5</td><td colspan="2">2,60</td><td>190</td></tr>
<tr><td>6</td><td>380</td><td>3,15</td><td colspan="2">3,95</td><td colspan="2">4,90</td><td>6,00</td><td>7,0</td><td>8,00</td><td>9,0</td><td>9,5</td><td colspan="2">11,0</td><td colspan="2">3,30</td><td>150</td></tr>
<tr><td>7</td><td>480</td><td>3,25</td><td colspan="2">4,30</td><td colspan="2">5,50</td><td>7,00</td><td>8,0</td><td>9,00</td><td>10,0</td><td>11,5</td><td colspan="2">13,0</td><td colspan="2">4,15</td><td>120</td></tr>
<tr><td>8</td><td>600</td><td>3,40</td><td colspan="2">4,70</td><td colspan="2">6,50</td><td>7,50</td><td>9,5</td><td>10,5</td><td>12,0</td><td>13,0</td><td colspan="2">15,5</td><td colspan="2">5,00</td><td>96</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td colspan="2">б</td><td colspan="2">в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td colspan="2">к</td><td></td><td></td><td></td><td></td></tr>
<tr><td colspan="22">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6" rowspan="5">Твердости чугуна и продолжительности обработки</td><td colspan="9">Твердость чугуна НВ, ГПа</td><td colspan="7">до 2,15 свыше 2,15</td></tr>
<tr><td colspan="9">Продолжительность обработки, мин.</td><td colspan="5">- до 10</td><td colspan="2">свыше 10</td></tr>
<tr><td colspan="9" rowspan="3">Коэффициент</td><td colspan="5"></td><td colspan="2" rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td colspan="3">1,1</td></tr>
<tr><td colspan="5"></td></tr>
<tr><td colspan="6" rowspan="5">Вида обработки</td><td colspan="9">Продольное и поперечное точение</td><td colspan="7">Растачивание</td></tr>
<tr><td colspan="16">Коэффициент</td></tr>
<tr><td colspan="9"></td><td colspan="7" rowspan="3">1,06</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7"></td></tr>
</table>


<a id="p100786"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету время по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="4%"><col width="6%"><col width="8%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="2%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="2%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="22">Неполное штучное время Горизонтально-расточные станки Продольное и поперечное точение, Ra 1,25, 1Т7 квалитет</td></tr>
<tr><td colspan="22">Чугун серый, НВ = 1,76 - 2,15 ГПа Резцы с пластинками ВК6 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="22">Карта 15</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="2">Диаметр обрабатываемой поверхности D, мм,</td><td>Глубина</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td colspan="2">50</td><td colspan="2">75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td colspan="2">250</td><td colspan="2">Добавлять на каждые 100 мм свыше 250</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td>до</td><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="8">10</td><td>120</td><td rowspan="8">1</td><td>4,00</td><td colspan="2">4,60</td><td colspan="2">5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>8,5</td><td>9,0</td><td colspan="2">10,5</td><td colspan="2">2,40</td><td rowspan="8">0,12</td><td>380</td><td rowspan="8">380</td><td rowspan="8">2,2</td></tr>
<tr><td>2</td><td>150</td><td>4,10</td><td colspan="2">4,85</td><td colspan="2">6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>9,5</td><td>10,5</td><td colspan="2">12,0</td><td colspan="2">3,05</td><td>300</td></tr>
<tr><td>3</td><td>190</td><td>4,20</td><td colspan="2">5,50</td><td colspan="2">6,5</td><td>7,5</td><td>9,0</td><td>10,0</td><td>10,5</td><td>11,5</td><td colspan="2">13,5</td><td colspan="2">3,80</td><td>240</td></tr>
<tr><td>4</td><td>240</td><td>4,35</td><td colspan="2">5,50</td><td colspan="2">7,0</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,5</td><td>13,5</td><td colspan="2">16,0</td><td colspan="2">4,80</td><td>190</td></tr>
<tr><td>5</td><td>300</td><td>4,50</td><td colspan="2">6,50</td><td colspan="2">8,0</td><td>9,5</td><td>11,5</td><td>13,0</td><td>14,5</td><td>16,0</td><td colspan="2">19,0</td><td colspan="2">6,00</td><td>150</td></tr>
<tr><td>6</td><td>380</td><td>4,75</td><td colspan="2">7,00</td><td colspan="2">9,0</td><td>11,0</td><td>13,5</td><td>15,5</td><td>17,5</td><td>19,5</td><td colspan="2">22,5</td><td colspan="2">7,50</td><td>120</td></tr>
<tr><td>7</td><td>480</td><td>5,50</td><td colspan="2">8,00</td><td colspan="2">10,5</td><td>13,0</td><td>16,0</td><td>18,5</td><td>21,0</td><td>23,5</td><td colspan="2">27,5</td><td colspan="2">9,50</td><td>96</td></tr>
<tr><td>8</td><td>600</td><td>5,50</td><td colspan="2">8,50</td><td colspan="2">12,0</td><td>15,0</td><td>18,5</td><td>21,5</td><td>24,5</td><td>27,5</td><td colspan="2">32,5</td><td colspan="2">12,00</td><td>75</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td colspan="2">б</td><td colspan="2">в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td colspan="2">к</td><td></td><td></td><td></td><td></td></tr>
<tr><td colspan="22">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6" rowspan="5">Твердости чугуна и продолжительности обработки</td><td colspan="9">Твердость чугуна НВ, ГПа</td><td colspan="3">до 2,15</td><td colspan="4">свыше 2,15</td></tr>
<tr><td colspan="9">Продолжительность обработки, мин.</td><td colspan="3">-</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td></tr>
<tr><td colspan="9" rowspan="3">Коэффициент</td><td colspan="3"></td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="6" rowspan="5">Вида обработки</td><td colspan="9">Продольное и поперечное точение</td><td colspan="7">Растачивание</td></tr>
<tr><td colspan="16">Коэффициент</td></tr>
<tr><td colspan="9"></td><td colspan="7" rowspan="3">1,06</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7"></td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="20%"><col width="11%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="3%"><col width="4%"><col width="4%"><col width="8%"><col width="7%"></colgroup>
<tr><td colspan="7">Неполное штучное время Прорезка канавок</td><td colspan="9">Горизонтально-расточные станки</td></tr>
<tr><td colspan="7" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="9">Суппорт планшайбы Резцы с пластинками ВК6</td></tr>
<tr><td colspan="9">Карта 16</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обрабатываемой</td><td>Ширина резца</td><td colspan="8">Глубина канавки l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td rowspan="2">поверхности D, мм, до</td><td rowspan="2">В, мм</td><td>3</td><td>4,5</td><td>6</td><td>8</td><td>10</td><td>12</td><td colspan="2">15</td><td colspan="2" rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">v, м/мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="8">Время на поверхность, мин.</td></tr>
<tr><td>1</td><td>50</td><td>3 - 5</td><td>2,4</td><td>2,5</td><td>2,6</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2" rowspan="5">0,08</td><td colspan="2" rowspan="4">47</td><td rowspan="11">1</td></tr>
<tr><td>2</td><td>75</td><td>3 - 5</td><td>2,6</td><td>2,7</td><td>2,8</td><td>2,9</td><td>3,0</td><td>-</td><td colspan="2">-</td></tr>
<tr><td>3</td><td>100</td><td rowspan="2">5 - 8</td><td>2,7</td><td>2,8</td><td>2,9</td><td>3,1</td><td>3,3</td><td>3,5</td><td colspan="2">3,7</td></tr>
<tr><td>4</td><td>125</td><td>2,9</td><td>3,0</td><td>3,1</td><td>3,3</td><td>3,6</td><td>3,8</td><td colspan="2">4,0</td></tr>
<tr><td>5</td><td>150</td><td rowspan="7">10 - 12</td><td>3,0</td><td>3,2</td><td>3,4</td><td>3,6</td><td>3,9</td><td>4,1</td><td colspan="2">4,4</td><td colspan="2">47 - 44</td></tr>
<tr><td>6</td><td>200</td><td>3,2</td><td>3,4</td><td>3,6</td><td>3,9</td><td>4,3</td><td>4,7</td><td colspan="2">5,0</td><td colspan="2" rowspan="3">0,1</td><td colspan="2" rowspan="2">39</td></tr>
<tr><td>7</td><td>250</td><td>3,5</td><td>3,7</td><td>4,0</td><td>4,4</td><td>4,8</td><td>5,3</td><td colspan="2">5,7</td></tr>
<tr><td>8</td><td>300</td><td>3,8</td><td>4,1</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,0</td><td colspan="2">6,5</td><td colspan="2">38 - 44</td></tr>
<tr><td>9</td><td>400</td><td>4,0</td><td>4,4</td><td>4,8</td><td>5,2</td><td>6,0</td><td>6,5</td><td colspan="2">7,0</td><td colspan="2" rowspan="3">0,12</td><td colspan="2">38</td></tr>
<tr><td>10</td><td>500</td><td>4,4</td><td>4,8</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td colspan="2">8,0</td><td colspan="2">35 - 39</td></tr>
<tr><td>11</td><td>600</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>8,8</td><td colspan="2">9,7</td><td colspan="2">34 - 38</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td colspan="2"></td><td colspan="2"></td><td></td></tr>
<tr><td colspan="16">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3" rowspan="4">Твердости чугуна</td><td colspan="11">Твердость чугуна НВ, ГПа до 2,15</td><td colspan="2">свыше 2,15</td></tr>
<tr><td colspan="11"></td><td colspan="2" rowspan="3">1,1</td></tr>
<tr><td colspan="7">Коэффициент</td><td colspan="2">1,0</td><td colspan="2"></td></tr>
</table>


<a id="p100824"></a>*Примечание.* При обработке внутренних канавок и канавок на торце время по карте принимать с коэффициентом К = 1,15.


<table>
<colgroup><col width="5%"><col width="11%"><col width="7%"><col width="7%"><col width="5%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="17">Неполное штучное время Горизонтально-расточные станки Обработка фасок и радиусов</td></tr>
<tr><td colspan="17">Чугун серый, НВ = 1,76 - 2,15 ГПа Суппорт планшайбы Единичное и мелкосерийное Резцы с пластинками ВК6, ВК8 производство</td></tr>
<tr><td colspan="17">Карта 17</td></tr>
<tr><td rowspan="4">N позиции</td><td rowspan="4">Диаметр обрабатываемой поверхности D, мм, до</td><td colspan="8">Обработка фасок</td><td colspan="7">Обработка радиусов</td></tr>
<tr><td colspan="5">Ширина фаски В, мм, до</td><td colspan="3">Режимы резания</td><td colspan="4">Размер радиуса, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td>3</td><td>5</td><td>8</td><td colspan="2">10</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td><td>3</td><td>5</td><td>8</td><td>10</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="5">Время на поверхность, мин.</td><td colspan="4">Время на поверхность, мин.</td></tr>
<tr><td>1</td><td>50</td><td>0,50</td><td>0,70</td><td>0,8</td><td colspan="2">1,00</td><td>23,0</td><td rowspan="7">75</td><td rowspan="7">1</td><td>1,6</td><td>1,7</td><td>1,9</td><td>2,1</td><td>16</td><td rowspan="7">75</td><td rowspan="7">1</td></tr>
<tr><td>2</td><td>100</td><td>0,70</td><td>0,80</td><td>1,0</td><td colspan="2">1,10</td><td>21,0</td><td>1,8</td><td>1,9</td><td>2,1</td><td>2,3</td><td>14</td></tr>
<tr><td>3</td><td>200</td><td>0,80</td><td>1,00</td><td>1,2</td><td colspan="2">1,35</td><td>14,0</td><td>1,9</td><td>2,1</td><td>2,4</td><td>2,6</td><td>10</td></tr>
<tr><td>4</td><td>300</td><td>0,90</td><td>1,10</td><td>1,3</td><td colspan="2">1,60</td><td>10,5</td><td>2,0</td><td>2,3</td><td>2,6</td><td>2,9</td><td>8</td></tr>
<tr><td>5</td><td>400</td><td>0,95</td><td>1,20</td><td>1,5</td><td colspan="2">1,80</td><td>8,5</td><td>2,1</td><td>2,5</td><td>3,0</td><td>3,4</td><td>6</td></tr>
<tr><td>6</td><td>500</td><td>1,10</td><td>1,35</td><td>1,7</td><td colspan="2">2,00</td><td>7,0</td><td>2,3</td><td>2,7</td><td>3,4</td><td>3,9</td><td>5</td></tr>
<tr><td>7</td><td>600</td><td>1,20</td><td>1,60</td><td>2,0</td><td colspan="2">2,45</td><td>5,5</td><td>2,5</td><td>3,0</td><td>3,9</td><td>4,4</td><td>4</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td></td><td></td><td></td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="3"></td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6" rowspan="2">Твердости чугуна</td><td colspan="6">Твердость чугуна НВ, ГПа</td><td colspan="5">до 2,15 свыше 2,15</td></tr>
<tr><td colspan="6">Коэффициент</td><td colspan="5">1,0 1,1</td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="11%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="3%"><col width="4%"><col width="4%"><col width="3%"><col width="5%"><col width="4%"><col width="7%"><col width="11%"></colgroup>
<tr><td colspan="16">Неполное штучное время Горизонтально-расточные станки Подрезка торцов</td></tr>
<tr><td colspan="16">Чугун серый, НВ = 1,76 - 2,15 ГПа Резцы из стали Р6М5 Сталь конструкционная углеродистая сигма = 0,59 - 0,74 ГПа Карта 18 в Единичное и мелкосерийное производство</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2">Диаметр обрабатываемой</td><td colspan="9">Длина обработки l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td colspan="2" rowspan="2">поверхности D, мм, до</td><td>3</td><td>5</td><td>8</td><td>10</td><td>12</td><td colspan="2">15</td><td colspan="2">20</td><td colspan="2" rowspan="2">S , о мм/об.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="9">Время на поверхность, мин.</td></tr>
<tr><td colspan="16">Чугун серый, НВ - 1,76 - 2,15 ГПа</td></tr>
<tr><td>1</td><td colspan="2">75</td><td>1,3</td><td>1,7</td><td>2,2</td><td>2,7</td><td>3,1</td><td colspan="2">3,6</td><td colspan="2">4,5</td><td colspan="2">5,4</td><td rowspan="10">28</td><td rowspan="10">1,5</td></tr>
<tr><td>2</td><td colspan="2">100</td><td>1,4</td><td>1,8</td><td>2,3</td><td>2,9</td><td>3,3</td><td colspan="2">3,8</td><td colspan="2">4,7</td><td colspan="2">5,1</td></tr>
<tr><td>3</td><td colspan="2">125</td><td>1,6</td><td>2,2</td><td>2,8</td><td>3,5</td><td>4,1</td><td colspan="2">4,7</td><td colspan="2">6,0</td><td colspan="2">4,0</td></tr>
<tr><td>4</td><td colspan="2">150</td><td>1,7</td><td>2,3</td><td>3,0</td><td>3,8</td><td>4,5</td><td colspan="2">5,0</td><td colspan="2">6,5</td><td colspan="2">3,7</td></tr>
<tr><td>5</td><td colspan="2">175</td><td>1,9</td><td>2,5</td><td>3,4</td><td>4,2</td><td>4,8</td><td colspan="2">5,5</td><td colspan="2">7,0</td><td colspan="2">3,3</td></tr>
<tr><td>6</td><td colspan="2">200</td><td>2,1</td><td>2,9</td><td>3,8</td><td>4,8</td><td>5,5</td><td colspan="2">6,5</td><td colspan="2">8,0</td><td colspan="2">2,9</td></tr>
<tr><td>7</td><td colspan="2">225</td><td>2,3</td><td>3,0</td><td>4,0</td><td>5,0</td><td>6,0</td><td colspan="2">7,0</td><td colspan="2">9,0</td><td colspan="2">2,6</td></tr>
<tr><td>8</td><td colspan="2">250</td><td>2,6</td><td>3,8</td><td>5,0</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td colspan="2">11,0</td><td colspan="2">21,0</td></tr>
<tr><td>9</td><td colspan="2">275</td><td>2,8</td><td>4,0</td><td>5,5</td><td>7,0</td><td>8,0</td><td colspan="2">9,0</td><td colspan="2">11,5</td><td colspan="2">2,0</td></tr>
<tr><td>10</td><td colspan="2">300</td><td>3,0</td><td>4,3</td><td>6,0</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td colspan="2">12,5</td><td colspan="2">1,8</td></tr>
<tr><td colspan="16">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td></tr>
<tr><td>11</td><td colspan="2">75</td><td>1,6</td><td>2,2</td><td>2,9</td><td>3,5</td><td>4,0</td><td colspan="2">4,8</td><td colspan="2">6,0</td><td colspan="2">4,0</td><td rowspan="10">30</td><td rowspan="10">1,5</td></tr>
<tr><td>12</td><td colspan="2">100</td><td>1,7</td><td>2,3</td><td>3,0</td><td>3,7</td><td>4,3</td><td colspan="2">5,0</td><td colspan="2">6,2</td><td colspan="2">3,75</td></tr>
<tr><td>13</td><td colspan="2">125</td><td>1,9</td><td>2,6</td><td>3,4</td><td>4,3</td><td>5,0</td><td colspan="2">6,0</td><td colspan="2">7,0</td><td colspan="2">3,2</td></tr>
<tr><td>14</td><td colspan="2">150</td><td>2,1</td><td>2,9</td><td>3,9</td><td>5,0</td><td>5,7</td><td colspan="2">6,5</td><td colspan="2">8,5</td><td colspan="2">2,75</td></tr>
<tr><td>15</td><td colspan="2">175</td><td>2,3</td><td>3,2</td><td>4,3</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">9,5</td><td colspan="2">2,45</td></tr>
<tr><td>16</td><td colspan="2">200</td><td>2,7</td><td>3,7</td><td>5,0</td><td>6,0</td><td>7,0</td><td colspan="2">8,5</td><td colspan="2">10,5</td><td colspan="2">2,15</td></tr>
<tr><td>17</td><td colspan="2">225</td><td>2,9</td><td>4,0</td><td>5,5</td><td>7,0</td><td>8,0</td><td colspan="2">9,5</td><td colspan="2">11,5</td><td colspan="2">1,95</td></tr>
<tr><td>18</td><td colspan="2">250</td><td>3,1</td><td>4,5</td><td>6,0</td><td>7,5</td><td>9,0</td><td colspan="2">10,5</td><td colspan="2">13,0</td><td colspan="2">17,5</td></tr>
<tr><td>19</td><td colspan="2">275</td><td>3,5</td><td>5,0</td><td>7,0</td><td>8,5</td><td>10,0</td><td colspan="2">12,0</td><td colspan="2">15,0</td><td colspan="2">15,0</td></tr>
<tr><td>20</td><td colspan="2">300</td><td>4,0</td><td>5,5</td><td>7,5</td><td>9,5</td><td>11,0</td><td colspan="2">13,0</td><td colspan="2">16,5</td><td colspan="2">1,35</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td colspan="2">ж</td><td colspan="4"></td></tr>
<tr><td colspan="16">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="5">Группы стали и предела прочности</td><td colspan="9">Группа стали Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="5">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="5">Предел прочности до сигма , ГПа 0,59 в</td><td colspan="2">0,59 - 0,74</td><td colspan="2">свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="3">0,59 - свыше 0,74 0,74</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент 0,8</td><td colspan="2"></td><td colspan="2" rowspan="3">1,25</td><td colspan="2" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,2 1,35</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td colspan="2" rowspan="4">Состояния обрабатываемой поверхности</td><td colspan="9">Состояние без корки и удара обрабатываемой поверхности</td><td colspan="5">по корке и на удар</td></tr>
<tr><td colspan="9"></td><td colspan="5" rowspan="3">1,2</td></tr>
<tr><td colspan="4">Коэффициент</td><td>0,1</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="15%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="9%"><col width="7%"><col width="3%"><col width="8%"></colgroup>
<tr><td colspan="13">Неполное штучное время Горизонтально-расточные станки Цекование торцов и отверстий</td></tr>
<tr><td colspan="13">Чугун серый, НВ = 1,76 - 2,15 ГПа Цековки и пластины из стали Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="13">Карта 19</td></tr>
<tr><td rowspan="4">N позиции</td><td rowspan="2">Диаметр обрабатываемой поверхности</td><td colspan="7">Глубина цекования l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>2,5</td><td>3,5</td><td>5</td><td>7</td><td>10</td><td>14</td><td>20</td><td rowspan="2">S , о мм/об.</td><td rowspan="2">v, м/ мин.</td><td colspan="2" rowspan="2">N , р кВт, до</td></tr>
<tr><td rowspan="2">D, мм, до</td><td colspan="7">Время на поверхность, мин.</td></tr>
<tr><td colspan="11">Подрезание торцов цековками</td></tr>
<tr><td>1</td><td>30</td><td>0,50</td><td>0,55</td><td>0,65</td><td>0,75</td><td>0,85</td><td>1,05</td><td>1,35</td><td rowspan="4">0,26 - 0,30</td><td>7,2</td><td colspan="2" rowspan="4"></td></tr>
<tr><td>2</td><td>40</td><td>0,55</td><td>0,60</td><td>0,70</td><td>0,85</td><td>1,00</td><td>1,25</td><td>1,60</td><td>7,5</td></tr>
<tr><td>3</td><td>55</td><td>0,65</td><td>0,75</td><td>0,90</td><td>1,05</td><td>1,35</td><td>1,70</td><td>2,20</td><td>7,0</td></tr>
<tr><td>4</td><td>72</td><td>0,75</td><td>0,90</td><td>1,10</td><td>1,30</td><td>1,65</td><td>2,15</td><td>2,80</td><td>6,7</td></tr>
<tr><td colspan="13">Цекование отверстий под головку болта</td></tr>
<tr><td>5</td><td>30</td><td>0,80</td><td>0,85</td><td>0,95</td><td>1,10</td><td>1,25</td><td>1,55</td><td>1,90</td><td rowspan="4">0,13 - 0,19</td><td>7,2</td><td colspan="2" rowspan="4">1,5</td></tr>
<tr><td>6</td><td>40</td><td>0,85</td><td>0,95</td><td>1,05</td><td>1,20</td><td>1,45</td><td>1,80</td><td>2,25</td><td>7,5</td></tr>
<tr><td>7</td><td>55</td><td>1,00</td><td>1,10</td><td>1,35</td><td>1,55</td><td>1,90</td><td>2,40</td><td>3,10</td><td>7,0</td></tr>
<tr><td>8</td><td>72</td><td>1,10</td><td>1,30</td><td>1,60</td><td>1,90</td><td>2,30</td><td>3,00</td><td>4,00</td><td>6,7</td></tr>
<tr><td colspan="13">Подрезание торцов пластинами</td></tr>
<tr><td>9</td><td>30</td><td>0,65</td><td>0,70</td><td>0,80</td><td>0,85</td><td>1,00</td><td>1,25</td><td>1,50</td><td rowspan="4">0,19 - 0,26</td><td>9,0</td><td colspan="2" rowspan="4"></td></tr>
<tr><td>10</td><td>40</td><td>0,70</td><td>0,75</td><td>0,85</td><td>1,00</td><td>1,15</td><td>1,45</td><td>1,80</td><td>9,5</td></tr>
<tr><td>11</td><td>55</td><td>0,80</td><td>0,90</td><td>2,8</td><td>1,25</td><td>1,55</td><td>2,00</td><td>2,50</td><td>8,5</td></tr>
<tr><td>12</td><td>72</td><td>0,90</td><td>1,00</td><td>3,0</td><td>1,45</td><td>1,80</td><td>2,30</td><td>3,00</td><td>9,0</td></tr>
<tr><td colspan="13">Цекование отверстий под головку болта пластинами</td></tr>
<tr><td>13</td><td>30</td><td>0,80</td><td>0,90</td><td>1,05</td><td>1,15</td><td>1,40</td><td>1,70</td><td>2,15</td><td rowspan="4">0,13 - 0,19</td><td>9,0</td><td colspan="2" rowspan="4"></td></tr>
<tr><td>14</td><td>40</td><td>0,90</td><td>1,00</td><td>1,15</td><td>1,35</td><td>1,60</td><td>2,00</td><td>2,60</td><td>9,5</td></tr>
<tr><td>15</td><td>55</td><td>1,05</td><td>1,20</td><td>1,45</td><td>1,70</td><td>2,15</td><td>2,70</td><td>3,60</td><td>8,5</td></tr>
<tr><td>16</td><td>72</td><td>1,20</td><td>1,40</td><td>1,70</td><td>2,10</td><td>2,60</td><td>3,30</td><td>4,30</td><td>9,0</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td></td><td></td><td colspan="2"></td></tr>
<tr><td colspan="13">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="10">Твердости чугуна Твердость чугуна НВ, ГПа до 2,15</td><td colspan="3">свыше 2,15</td></tr>
<tr><td colspan="10"></td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td colspan="8">Коэффициент</td><td colspan="2">1,0</td></tr>
<tr><td colspan="10"></td></tr>
<tr><td colspan="10">Вылета шпинделя Вылет шпинделя, мм 200 250</td><td colspan="2">350</td><td>450</td></tr>
<tr><td colspan="10"></td><td colspan="2" rowspan="3">1,1</td><td rowspan="3">1,2</td></tr>
<tr><td colspan="8">Коэффициент</td><td colspan="2">1,0 1,1</td></tr>
</table>


<a id="p100896"></a>*Примечание.* При обработке обратными цековками и пластинами время по карте принимать с коэффициентом К = 1,15.


<table>
<colgroup><col width="5%"><col width="11%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="8%"><col width="4%"><col width="4%"><col width="8%"></colgroup>
<tr><td colspan="17">Неполное штучное время Горизонтально-расточные станки Нарезание внутренней метрической резьбы на проход, ГТ9 квалитет Резцы из стали Р6М5 Чугун серый, НВ = 1,76 - 2,15 ГПа</td></tr>
<tr><td colspan="17">Единичное и мелкосерийное производство Карта 20</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр нарезаемой резьбы D, мм</td><td colspan="8">Длина нарезаемой резьбы l, мм, до</td><td colspan="7">Режимы резания</td></tr>
<tr><td>25</td><td colspan="2">50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td rowspan="2">Р, мм</td><td colspan="3">Число проходов i</td><td colspan="3">v, м/мин.</td></tr>
<tr><td colspan="8">Время на поверхность, мин.</td><td colspan="2">черновые</td><td>чистовые</td><td colspan="2">черновые</td><td>чистовые</td></tr>
<tr><td>1</td><td rowspan="4">36 - 42</td><td>4,5</td><td colspan="2">7,5</td><td>11,0</td><td>14,5</td><td>18,5</td><td>21,5</td><td>-</td><td>1</td><td colspan="2" rowspan="3">7</td><td rowspan="4">2</td><td colspan="2">15</td><td rowspan="18">4</td></tr>
<tr><td>2</td><td>5,0</td><td colspan="2">6,5</td><td>8,5</td><td>9,5</td><td>12,5</td><td>14,5</td><td>-</td><td>2</td><td colspan="2" rowspan="2">11</td></tr>
<tr><td>3</td><td>4,0</td><td colspan="2">5,5</td><td>6,5</td><td>8,0</td><td>9,5</td><td>11,0</td><td>-</td><td>3</td></tr>
<tr><td>4</td><td>4,5</td><td colspan="2">5,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,0</td><td>-</td><td>4</td><td colspan="2">8</td><td colspan="2">9</td></tr>
<tr><td>5</td><td rowspan="4">48</td><td>6,0</td><td colspan="2">9,0</td><td>13,5</td><td>18,0</td><td>22,5</td><td>27,0</td><td>33,0</td><td>1</td><td colspan="2" rowspan="3">7</td><td rowspan="4">2</td><td colspan="2">15</td></tr>
<tr><td>6</td><td>5,5</td><td colspan="2">7,0</td><td>9,5</td><td>12,0</td><td>14,5</td><td>17,0</td><td>20,5</td><td>2</td><td colspan="2" rowspan="2">11</td></tr>
<tr><td>7</td><td>5,0</td><td colspan="2">6,0</td><td>7,5</td><td>9,0</td><td>11,0</td><td>12,5</td><td>15,0</td><td>3</td></tr>
<tr><td>8</td><td>5,0</td><td colspan="2">6,0</td><td>7,5</td><td>9,0</td><td>11,0</td><td>12,5</td><td>14,5</td><td>4</td><td colspan="2">8</td><td colspan="2">9</td></tr>
<tr><td>9</td><td rowspan="4">64</td><td>7,5</td><td colspan="2">11,0</td><td>16,5</td><td>22,0</td><td>27,0</td><td>33,0</td><td>40,0</td><td>1</td><td colspan="2" rowspan="3">7</td><td rowspan="4">2</td><td colspan="2">15</td></tr>
<tr><td>10</td><td>6,0</td><td colspan="2">8,5</td><td>11,5</td><td>14,5</td><td>18,0</td><td>21,0</td><td>25,0</td><td>2</td><td colspan="2" rowspan="2">11</td></tr>
<tr><td>11</td><td>5,5</td><td colspan="2">7,0</td><td>9,0</td><td>11,0</td><td>13,5</td><td>16,0</td><td>18,5</td><td>3</td></tr>
<tr><td>12</td><td>6,0</td><td colspan="2">7,5</td><td>9,5</td><td>11,5</td><td>13,5</td><td>15,5</td><td>18,5</td><td>4</td><td colspan="2">8</td><td colspan="2">9</td></tr>
<tr><td>13</td><td rowspan="4">72</td><td>8,5</td><td colspan="2">13,5</td><td>20,0</td><td>27,0</td><td>33,0</td><td>40,0</td><td>50,0</td><td>1</td><td colspan="2" rowspan="3">7</td><td rowspan="4">2</td><td colspan="2">15</td></tr>
<tr><td>14</td><td>7,0</td><td colspan="2">10,0</td><td>13,5</td><td>17,5</td><td>21,5</td><td>25,0</td><td>31,0</td><td>2</td><td colspan="2" rowspan="2">11</td></tr>
<tr><td>15</td><td>6,0</td><td colspan="2">8,0</td><td>10,5</td><td>13,0</td><td>16,0</td><td>19,0</td><td>22,0</td><td>3</td></tr>
<tr><td>16</td><td>7,0</td><td colspan="2">9,0</td><td>11,0</td><td>13,5</td><td>16,0</td><td>18,5</td><td>22,0</td><td>4</td><td colspan="2">8</td><td colspan="2">9</td></tr>
<tr><td>17</td><td rowspan="3">90</td><td>8,0</td><td colspan="2">11,5</td><td>16,0</td><td>21,5</td><td>25,0</td><td>30,0</td><td>36,0</td><td>2</td><td colspan="2" rowspan="2">7</td><td rowspan="3">2</td><td colspan="2" rowspan="2">11</td></tr>
<tr><td>18</td><td>7,0</td><td colspan="2">9,5</td><td>12,5</td><td>15,5</td><td>18,5</td><td>21,5</td><td>26,0</td><td>3</td></tr>
<tr><td>19</td><td>8,0</td><td colspan="2">10,0</td><td>13,0</td><td>15,5</td><td>19,0</td><td>22,0</td><td>26,0</td><td>4</td><td colspan="2">8</td><td colspan="2">9</td><td rowspan="6">2</td></tr>
<tr><td>20</td><td rowspan="3">100 - 125</td><td>9,5</td><td colspan="2">14,0</td><td>19,5</td><td>25,0</td><td>30,0</td><td>36,0</td><td>44,0</td><td>2</td><td colspan="2" rowspan="2">7</td><td rowspan="3">2</td><td colspan="2" rowspan="2">11</td></tr>
<tr><td>21</td><td>8,5</td><td colspan="2">11,0</td><td>15,0</td><td>18,5</td><td>22,5</td><td>26,0</td><td>31,0</td><td>3</td></tr>
<tr><td>22</td><td>9,0</td><td colspan="2">12,0</td><td>15,0</td><td>18,5</td><td>22,5</td><td>26,0</td><td>31,0</td><td>4</td><td colspan="2">8</td><td colspan="2">9</td></tr>
<tr><td>23</td><td rowspan="3">140 - 160</td><td>11,5</td><td colspan="2">16,5</td><td>23,0</td><td>30,0</td><td>37,0</td><td>44,0</td><td>54,0</td><td>2</td><td colspan="2" rowspan="2">7</td><td rowspan="2"></td><td colspan="2" rowspan="2">11</td></tr>
<tr><td>24</td><td>9,5</td><td colspan="2">13,0</td><td>17,5</td><td>22,0</td><td>27,0</td><td>32,0</td><td>39,0</td><td>3</td></tr>
<tr><td>25</td><td>10,5</td><td colspan="2">14,0</td><td>18,0</td><td>22,0</td><td>27,0</td><td>32,0</td><td>37,0</td><td>4</td><td colspan="2">8</td><td></td><td colspan="2">9</td><td rowspan="4">4</td></tr>
<tr><td>26</td><td rowspan="3">180 - 200</td><td>13,5</td><td colspan="2">20,0</td><td>30,0</td><td>37,0</td><td>46,0</td><td>55,0</td><td>68,0</td><td>2</td><td colspan="2" rowspan="2">7</td><td rowspan="4">2</td><td colspan="2" rowspan="2">11</td></tr>
<tr><td>27</td><td>11,5</td><td colspan="2">16,0</td><td>22,0</td><td>27,0</td><td>33,0</td><td>39,0</td><td>48,0</td><td>3</td></tr>
<tr><td>28</td><td>12,5</td><td colspan="2">17,0</td><td>22,0</td><td>28,0</td><td>34,0</td><td>39,0</td><td>48,0</td><td>4</td><td colspan="2">8</td><td colspan="2">9</td></tr>
<tr><td></td><td>Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td></td><td colspan="2"></td><td colspan="2"></td><td></td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Твердости чугуна и продолжительности</td><td colspan="9">Твердость чугуна НВ, ГПа до 2,15</td><td colspan="4">свыше 2,15</td></tr>
<tr><td colspan="4" rowspan="4">обработки</td><td colspan="9">Продолжительность обработки -</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td></tr>
<tr><td colspan="9"></td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,25</td></tr>
<tr><td colspan="8">Коэффициент 1,0</td><td></td></tr>
</table>


<a id="p100932"></a>*Примечание.* При нарезании резьбы в упор время по карте принимать с коэффициентом К = 1,2.


<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="3%"><col width="2%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="19">Неполное штучное время Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="19" rowspan="2">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Единичное и мелкосерийное производство</td><td colspan="7">Борштанги консольные Резцы из стали Р6М5</td></tr>
<tr><td colspan="7">Карта 21 Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="18">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td colspan="2">600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="18">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="19">10</td><td>30</td><td>2</td><td>1,30</td><td>1,65</td><td>2,00</td><td>2,40</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,20</td><td>380</td><td>36</td><td>1,2</td></tr>
<tr><td>2</td><td rowspan="2">48</td><td>3</td><td>1,40</td><td>1,85</td><td>2,30</td><td>2,75</td><td>3,90</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,40</td><td rowspan="2">150</td><td rowspan="2">22,5</td><td>1,7</td></tr>
<tr><td>3</td><td>5</td><td>1,45</td><td>2,00</td><td>2,50</td><td>3,00</td><td>3,80</td><td>4,30</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,35</td><td>1,7</td></tr>
<tr><td>4</td><td rowspan="2">60</td><td>3</td><td>1,40</td><td>1,90</td><td>2,40</td><td>2,95</td><td>3,65</td><td>4,15</td><td>4,65</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,45</td><td rowspan="2">120</td><td rowspan="2">22,5</td><td>1,2</td></tr>
<tr><td>5</td><td>5</td><td>1,55</td><td>2,20</td><td>2,85</td><td>3,50</td><td>4,40</td><td>5,00</td><td>5,50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,35</td><td>1,7</td></tr>
<tr><td>6</td><td rowspan="3">75</td><td>3</td><td>1,45</td><td>2,00</td><td>2,60</td><td>3,15</td><td>3,95</td><td>4,50</td><td>5,00</td><td>5,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,50</td><td rowspan="3">96</td><td rowspan="3">22,5</td><td>1,4</td></tr>
<tr><td>7</td><td>5</td><td>1,70</td><td>2,50</td><td>3,35</td><td>4,15</td><td>5,00</td><td>6,00</td><td>7,00</td><td>8,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,35</td><td>1,4</td></tr>
<tr><td>8</td><td>8</td><td>2,00</td><td>3,15</td><td>4,30</td><td>5,50</td><td>7,00</td><td>8,00</td><td>9,00</td><td>10,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,25</td><td>2,0</td></tr>
<tr><td>9</td><td rowspan="3">96</td><td>3</td><td>1,55</td><td>2,30</td><td>3,05</td><td>3,75</td><td>4,75</td><td>5,50</td><td>6,00</td><td>7,00</td><td>8,0</td><td>9,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,50</td><td rowspan="3">75</td><td rowspan="3">22,5</td><td>1,4</td></tr>
<tr><td>10</td><td>5</td><td>1,85</td><td>2,90</td><td>3,95</td><td>5,00</td><td>6,00</td><td>7,50</td><td>8,50</td><td>9,5</td><td>11,0</td><td>13,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,35</td><td>1,4</td></tr>
<tr><td>11</td><td>8</td><td>2,20</td><td>3,65</td><td>5,00</td><td>6,50</td><td>8,00</td><td>9,50</td><td>11,0</td><td>12,5</td><td>14,5</td><td>17,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,25</td><td>2,0</td></tr>
<tr><td>12</td><td rowspan="4">120</td><td>3</td><td>1,65</td><td>2,55</td><td>3,50</td><td>4,40</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,5</td><td>9,5</td><td>11,5</td><td>13,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,50</td><td rowspan="4">60</td><td rowspan="4">22,5</td><td>1,4</td></tr>
<tr><td>13</td><td>5</td><td>1,90</td><td>3,05</td><td>4,15</td><td>5,50</td><td>6,50</td><td>8,00</td><td>9,00</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,40</td><td>1,7</td></tr>
<tr><td>14</td><td>8</td><td>2,30</td><td>3,80</td><td>5,50</td><td>7,00</td><td>8,50</td><td>10,0</td><td>11,5</td><td>13,0</td><td>15,5</td><td>18,5</td><td>21,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,30</td><td>2,0</td></tr>
<tr><td>15</td><td>12</td><td>2,65</td><td>4,50</td><td>6,50</td><td>8,00</td><td>10,0</td><td>12,0</td><td>14,0</td><td>15,5</td><td>18,5</td><td>22,0</td><td>26,0</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,25</td><td>2,9</td></tr>
<tr><td>16</td><td rowspan="4">150</td><td>3</td><td>1,80</td><td>2,95</td><td>4,10</td><td>5,00</td><td>6,50</td><td>8,00</td><td>9,00</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td>21</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,50</td><td rowspan="4">48</td><td rowspan="4">22,5</td><td>1,4</td></tr>
<tr><td>17</td><td>5</td><td>2,10</td><td>3,55</td><td>5,00</td><td>6,50</td><td>8,00</td><td>9,50</td><td>11,00</td><td>12,5</td><td>14,5</td><td>17,5</td><td>20,5</td><td>23,5</td><td>26</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,40</td><td>1,7</td></tr>
<tr><td>18</td><td>8</td><td>2,60</td><td>4,60</td><td>6,50</td><td>8,50</td><td>10,5</td><td>12,5</td><td>14,5</td><td>16,5</td><td>19,5</td><td>23,5</td><td>27,5</td><td>31,5</td><td>35</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,30</td><td>2,0</td></tr>
<tr><td>19</td><td>12</td><td>3,05</td><td>5,50</td><td>7,50</td><td>10,0</td><td>12,5</td><td>14,5</td><td>17,0</td><td>19,0</td><td>22,5</td><td>27,0</td><td>32,0</td><td>36,5</td><td>41</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>0,25</td><td>2,9</td></tr>
<tr><td colspan="3">Индекс</td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="2">п</td><td>р</td><td>с</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="3%"><col width="2%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="19">Неполное штучное время Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="19" rowspan="2">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Единичное и мелкосерийное производство</td><td colspan="7">Борштанги консольные Резцы из стали Р6М5</td></tr>
<tr><td colspan="7">Карта 21 Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="18">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td colspan="2">600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="18">Время на проход, мин.</td></tr>
<tr><td>20</td><td rowspan="16">10</td><td rowspan="4">190</td><td>3</td><td>2,00</td><td>3,45</td><td>4,85</td><td>6,5</td><td>8,0</td><td>9,5</td><td>11,0</td><td>12,5</td><td>14,5</td><td>17,5</td><td>20,5</td><td>23,0</td><td>26,0</td><td>29,0</td><td colspan="2">33,5</td><td>-</td><td>-</td><td>0,5</td><td rowspan="4">38</td><td rowspan="4">22,5</td><td>1,4</td></tr>
<tr><td>21</td><td>5</td><td>2,35</td><td>4,20</td><td>6,00</td><td>8,0</td><td>10,0</td><td>12,0</td><td>13,5</td><td>15,5</td><td>18,0</td><td>22,0</td><td>25,5</td><td>29,0</td><td>33,0</td><td>36,5</td><td colspan="2">42,0</td><td>-</td><td>-</td><td>0,40</td><td>1,7</td></tr>
<tr><td>22</td><td>8</td><td>3,05</td><td>5,50</td><td>8,00</td><td>10,5</td><td>13,0</td><td>16,0</td><td>18,0</td><td>20,5</td><td>24,5</td><td>29,5</td><td>34,5</td><td>39,5</td><td>44,5</td><td>49,5</td><td colspan="2">57,0</td><td>-</td><td>-</td><td>0,30</td><td>2,0</td></tr>
<tr><td>23</td><td>12</td><td>3,45</td><td>6,00</td><td>9,00</td><td>11,5</td><td>14,5</td><td>17,5</td><td>20,0</td><td>23,0</td><td>27,0</td><td>32,5</td><td>38,0</td><td>43,5</td><td>49,0</td><td>55,0</td><td colspan="2">63,0</td><td>-</td><td>-</td><td>0,25</td><td>2,9</td></tr>
<tr><td>24</td><td rowspan="4">240</td><td>3</td><td>2,25</td><td>4,05</td><td>6,00</td><td>8,0</td><td>10,0</td><td>11,5</td><td>13,5</td><td>15,5</td><td>18,0</td><td>21,5</td><td>25,5</td><td>29,0</td><td>32,5</td><td>36,5</td><td colspan="2">42,0</td><td>51</td><td>7,5</td><td>0,50</td><td rowspan="4">30</td><td rowspan="4">22,5</td><td>1,4</td></tr>
<tr><td>25</td><td>5</td><td>2,70</td><td>5,00</td><td>7,00</td><td>9,5</td><td>12,0</td><td>14,5</td><td>16,5</td><td>19,0</td><td>22,5</td><td>27,0</td><td>31,5</td><td>36,0</td><td>40,5</td><td>45,0</td><td colspan="2">52,0</td><td>64</td><td>9,0</td><td>0,40</td><td>1,7</td></tr>
<tr><td>26</td><td>8</td><td>3,45</td><td>6,50</td><td>9,50</td><td>12,5</td><td>16,0</td><td>19,0</td><td>22,0</td><td>25,0</td><td>29,5</td><td>35,5</td><td>42,0</td><td>48,0</td><td>54,0</td><td>60,0</td><td colspan="2">70,0</td><td>85</td><td>12,0</td><td>0,30</td><td>2,0</td></tr>
<tr><td>27</td><td>12</td><td>4,05</td><td>7,50</td><td>11,00</td><td>14,5</td><td>18,0</td><td>21,5</td><td>25,0</td><td>28,0</td><td>33,5</td><td>40,0</td><td>47,0</td><td>54,0</td><td>61,0</td><td>68,0</td><td colspan="2">78,0</td><td>95</td><td>14,5</td><td>0,25</td><td>2,9</td></tr>
<tr><td>28</td><td rowspan="4">300</td><td>3</td><td>2,50</td><td>4,80</td><td>7,00</td><td>9,5</td><td>12,0</td><td>14,0</td><td>16,5</td><td>19,0</td><td>22,0</td><td>27,0</td><td>31,5</td><td>36,0</td><td>40,5</td><td>45,0</td><td colspan="2">52,0</td><td>63</td><td>9,0</td><td>0,50</td><td rowspan="4">24</td><td rowspan="4">22,5</td><td>1,4</td></tr>
<tr><td>29</td><td>5</td><td>3,00</td><td>6,00</td><td>8,50</td><td>11,0</td><td>14,0</td><td>17,0</td><td>19,5</td><td>22,5</td><td>26,5</td><td>32,0</td><td>37,5</td><td>43,0</td><td>48,5</td><td>54,0</td><td colspan="2">63,0</td><td>76</td><td>11,5</td><td>0,40</td><td>1,7</td></tr>
<tr><td>30</td><td>8</td><td>4,15</td><td>8,00</td><td>12,00</td><td>16,0</td><td>20,0</td><td>24,0</td><td>28,0</td><td>32,0</td><td>37,5</td><td>45,5</td><td>54,0</td><td>61,0</td><td>69,0</td><td>77,0</td><td colspan="2">89,0</td><td>108</td><td>15,0</td><td>0,30</td><td>2,0</td></tr>
<tr><td>31</td><td>12</td><td>5,00</td><td>10,0</td><td>14,0</td><td>19,0</td><td>23,5</td><td>28,0</td><td>32,5</td><td>37,0</td><td>44,0</td><td>53,0</td><td>62,0</td><td>72,0</td><td>81,0</td><td>90,0</td><td colspan="2">104,0</td><td>126</td><td>18,0</td><td>0,25</td><td>2,9</td></tr>
<tr><td>32</td><td rowspan="4">380</td><td>3</td><td>2,80</td><td>5,50</td><td>8,00</td><td>11,0</td><td>14,0</td><td>17,0</td><td>19,5</td><td>22,0</td><td>26,5</td><td>32,0</td><td>37,5</td><td>43,0</td><td>48,5</td><td>54,0</td><td colspan="2">62,0</td><td>76</td><td>11,5</td><td>0,50</td><td rowspan="4">19</td><td rowspan="4">23</td><td>1,4</td></tr>
<tr><td>33</td><td>5</td><td>3,50</td><td>7,00</td><td>10,5</td><td>14,0</td><td>17,5</td><td>21,0</td><td>24,0</td><td>27,5</td><td>33,0</td><td>39,5</td><td>46,5</td><td>53,0</td><td>60,0</td><td>67,0</td><td colspan="2">78,0</td><td>95</td><td>14,5</td><td>0,40</td><td>1,7</td></tr>
<tr><td>34</td><td>8</td><td>4,65</td><td>9,00</td><td>14,0</td><td>18,5</td><td>23,0</td><td>27,5</td><td>32,0</td><td>37,0</td><td>44,0</td><td>53,0</td><td>62,0</td><td>71,0</td><td>80,0</td><td>90,0</td><td colspan="2">103,0</td><td>126</td><td>19,0</td><td>0,30</td><td>2,0</td></tr>
<tr><td>35</td><td>12</td><td>6,00</td><td>11,0</td><td>17,0</td><td>22,0</td><td>28,0</td><td>33,5</td><td>39,0</td><td>44,5</td><td>53,0</td><td>64,0</td><td>75,0</td><td>86,0</td><td>96,0</td><td>107,0</td><td colspan="2">124,0</td><td>151</td><td>23,0</td><td>0,25</td><td>2,9</td></tr>
<tr><td colspan="3">Индекс</td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="2">п</td><td>р</td><td>с</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="16%"><col width="25%"><col width="5%"><col width="5%"><col width="4%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"></colgroup>
<tr><td colspan="9">Неполное штучное время Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="9" rowspan="2">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Единичное и мелкосерийное производство</td><td colspan="5">Борштанги консольные Резцы из стали Р6М5</td></tr>
<tr><td colspan="5">Карта 21 Лист 3</td></tr>
<tr><td colspan="14">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="6">Группы стали, предела прочности и продолжительности обработки</td><td>Группа стали</td><td colspan="6">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="6">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td colspan="2">свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td>Продолжительность обработки, мин.</td><td>до 10</td><td>свыше 10</td><td colspan="2">-</td><td>до 10</td><td>свыше 10</td><td>до 10</td><td>свыше 10</td><td>до 10</td><td>свыше 10</td><td>до 10</td><td>свыше 10</td></tr>
<tr><td rowspan="3">Коэффициент</td><td rowspan="3">0,9</td><td rowspan="3">0,8</td><td colspan="2"></td><td rowspan="3">1,1</td><td rowspan="3">1,25</td><td></td><td rowspan="3">1,1</td><td rowspan="3">1,1</td><td rowspan="3">1,2</td><td rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td></td><td>1,0</td></tr>
<tr><td colspan="2"></td><td></td></tr>
<tr><td rowspan="2">Состояния обрабатываемой поверхности</td><td>Состояние обрабатываемой поверхности</td><td colspan="2">без корки и удара</td><td colspan="10">по корке и на удар</td></tr>
<tr><td>Коэффициент</td><td colspan="2">1,0</td><td colspan="10">1,2</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="5%"></colgroup>
<tr><td colspan="26">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="26">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Борштанги консольные в Резцы с пластинками Т5К10 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="23">Карта 22</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td>Глубина</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td>обрабатываемого отверстия D, мм,</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="19">10</td><td>30</td><td>2</td><td>1,20</td><td>1,35</td><td>1,45</td><td>1,60</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,25</td><td colspan="2">750</td><td>76</td><td>1,0</td></tr>
<tr><td>2</td><td rowspan="2">48</td><td>3</td><td>1,20</td><td>1,35</td><td>1,50</td><td>1,70</td><td>2,05</td><td>2,25</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,35</td><td colspan="2" rowspan="2">480</td><td rowspan="2">72</td><td>2,0</td></tr>
<tr><td>3</td><td>5</td><td>1,25</td><td>1,50</td><td>1,70</td><td>1,95</td><td>2,40</td><td>2,60</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,25</td><td>2,9</td></tr>
<tr><td>4</td><td rowspan="2">60</td><td>3</td><td>1,20</td><td>1,40</td><td>1,65</td><td>1,85</td><td>2,25</td><td>2,45</td><td>2,65</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,45</td><td colspan="2" rowspan="2">300</td><td rowspan="2">57</td><td>2,0</td></tr>
<tr><td>5</td><td>5</td><td>1,30</td><td>1,55</td><td>1,80</td><td>2,05</td><td>2,55</td><td>2,80</td><td>3,05</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,35</td><td>2,9</td></tr>
<tr><td>6</td><td rowspan="3">75</td><td>3</td><td>1,25</td><td>1,45</td><td>1,70</td><td>1,90</td><td>2,35</td><td>2,60</td><td>2,80</td><td>3,05</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,50</td><td colspan="2" rowspan="3">240</td><td rowspan="3">57</td><td>3,0</td></tr>
<tr><td>7</td><td>5</td><td>1,30</td><td>1,65</td><td>1,95</td><td>2,30</td><td>2,85</td><td>3,15</td><td>3,50</td><td>3,80</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,35</td><td>2,9</td></tr>
<tr><td>8</td><td>8</td><td>1,45</td><td>1,95</td><td>2,40</td><td>2,85</td><td>3,50</td><td>3,95</td><td>4,45</td><td>4,50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,25</td><td>3,4</td></tr>
<tr><td>9</td><td rowspan="3">96</td><td>3</td><td>1,25</td><td>1,50</td><td>1,75</td><td>2,05</td><td>2,50</td><td>2,75</td><td>3,00</td><td>3,30</td><td>3,65</td><td>4,20</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,56</td><td colspan="2" rowspan="3">190</td><td rowspan="3">57</td><td>2,4</td></tr>
<tr><td>10</td><td>5</td><td>1,40</td><td>1,80</td><td>2,20</td><td>2,60</td><td>3,25</td><td>3,65</td><td>4,05</td><td>4,45</td><td>5,00</td><td>6,00</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,33</td><td>2,9</td></tr>
<tr><td>11</td><td>8</td><td>1,45</td><td>1,95</td><td>2,45</td><td>2,90</td><td>3,60</td><td>4,10</td><td>4,55</td><td>5,00</td><td>6,00</td><td>7,00</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,30</td><td>4,1</td></tr>
<tr><td>12</td><td rowspan="4">120</td><td>3</td><td>1,30</td><td>1,60</td><td>1,95</td><td>2,23</td><td>2,80</td><td>3,15</td><td>3,45</td><td>3,80</td><td>4,30</td><td>4,95</td><td>6,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,56</td><td colspan="2" rowspan="4">150</td><td rowspan="4">56</td><td>2,4</td></tr>
<tr><td>13</td><td>5</td><td>1,40</td><td>1,80</td><td>2,20</td><td>2,60</td><td>3,25</td><td>3,65</td><td>4,05</td><td>4,45</td><td>5,00</td><td>6,00</td><td>7,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,45</td><td>3,4</td></tr>
<tr><td>14</td><td>8</td><td>1,50</td><td>2,00</td><td>2,45</td><td>3,05</td><td>3,80</td><td>4,30</td><td>4,80</td><td>5,50</td><td>6,00</td><td>7,00</td><td>8,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,35</td><td>4,1</td></tr>
<tr><td>15</td><td>12</td><td>1,80</td><td>2,65</td><td>3,45</td><td>4,30</td><td>5,50</td><td>6,00</td><td>7,00</td><td>8,00</td><td>9,00</td><td>11,0</td><td>17,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,22</td><td>4,9</td></tr>
<tr><td>16</td><td rowspan="4">150</td><td>3</td><td>1,35</td><td>1,75</td><td>2,15</td><td>2,55</td><td>3,20</td><td>3,60</td><td>4,00</td><td>4,45</td><td>5,00</td><td>6,00</td><td>7,0</td><td>7,5</td><td>8,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,56</td><td colspan="2" rowspan="4">120</td><td rowspan="4">56</td><td>2,4</td></tr>
<tr><td>17</td><td>5</td><td>1,45</td><td>1,95</td><td>2,45</td><td>2,95</td><td>3,70</td><td>4,20</td><td>4,70</td><td>5,00</td><td>6,00</td><td>7,00</td><td>8,0</td><td>9,0</td><td>10,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,45</td><td>3,4</td></tr>
<tr><td>18</td><td>8</td><td>1,60</td><td>2,25</td><td>2,90</td><td>3,55</td><td>4,45</td><td>5,00</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,50</td><td>10,0</td><td>11,5</td><td>12,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,35</td><td>4,1</td></tr>
<tr><td>19</td><td>12</td><td>2,00</td><td>3,05</td><td>4,10</td><td>5,00</td><td>6,50</td><td>7,50</td><td>8,50</td><td>9,50</td><td>11,0</td><td>13,00</td><td>15,5</td><td>17,5</td><td>19,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,22</td><td>4,9</td></tr>
<tr><td colspan="3">Индекс</td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="5%"></colgroup>
<tr><td colspan="26">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="26">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Борштанги консольные в Резцы с пластинками Т5К10 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="23">Карта 22</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td>Глубина</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td>обрабатываемого отверстия D, мм,</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>20</td><td rowspan="16">10</td><td rowspan="4">190</td><td>3</td><td>1,40</td><td>1,90</td><td>2,40</td><td>2,95</td><td>3,65</td><td>4,15</td><td>4,65</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,0</td><td>11,0</td><td>13,0</td><td>-</td><td>-</td><td>0,56</td><td colspan="2" rowspan="3">96</td><td rowspan="3">57</td><td>2,4</td></tr>
<tr><td>21</td><td>5</td><td>1,55</td><td>2,20</td><td>2,80</td><td>3,45</td><td>4,30</td><td>4,95</td><td>5,50</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,5</td><td>13,5</td><td>15,5</td><td>-</td><td>-</td><td>0,45</td><td>3,4</td></tr>
<tr><td>22</td><td>8</td><td>1,75</td><td>2,55</td><td>3,40</td><td>4,25</td><td>5,50</td><td>6,00</td><td>7,00</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,5</td><td>14,0</td><td>16,0</td><td>17,5</td><td>20,0</td><td>-</td><td>-</td><td>0,35</td><td>4,1</td></tr>
<tr><td>23</td><td>12</td><td>2,20</td><td>3,50</td><td>4,80</td><td>6,00</td><td>7,50</td><td>9,00</td><td>10,50</td><td>11,5</td><td>13,5</td><td>16,0</td><td>19,0</td><td>21,5</td><td>24,0</td><td>16,5</td><td>30,5</td><td>-</td><td>-</td><td>0,22</td><td colspan="2" rowspan="4">75</td><td rowspan="4">56</td><td>4,9</td></tr>
<tr><td>24</td><td rowspan="4">240</td><td>3</td><td>1,50</td><td>2,15</td><td>2,80</td><td>3,45</td><td>4,35</td><td>5,00</td><td>5,50</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>12,5</td><td>14,0</td><td>16,0</td><td>19,0</td><td>2,60</td><td>0,56</td><td>2,4</td></tr>
<tr><td>25</td><td>5</td><td>1,66</td><td>2,45</td><td>3,25</td><td>4,00</td><td>5,00</td><td>6,00</td><td>7,00</td><td>7,5</td><td>8,5</td><td>10,5</td><td>12,0</td><td>13,5</td><td>15,5</td><td>17,0</td><td>19,5</td><td>23,5</td><td>3,25</td><td>0,45</td><td>3,4</td></tr>
<tr><td>26</td><td>8</td><td>1,90</td><td>2,95</td><td>4,00</td><td>5,00</td><td>6,50</td><td>7,50</td><td>8,50</td><td>9,5</td><td>11,0</td><td>13,0</td><td>15,5</td><td>17,5</td><td>19,5</td><td>22,0</td><td>25,0</td><td>30,5</td><td>4,15</td><td>0,35</td><td>4,1</td></tr>
<tr><td>27</td><td>12</td><td>2,55</td><td>4,30</td><td>6,00</td><td>8,00</td><td>9,50</td><td>11,5</td><td>13,00</td><td>15,0</td><td>17,5</td><td>21,0</td><td>24,5</td><td>28,0</td><td>31,0</td><td>34,5</td><td>40,0</td><td>48,5</td><td>6,50</td><td>0,22</td><td colspan="2" rowspan="4">60</td><td rowspan="4">56</td><td>4,9</td></tr>
<tr><td>28</td><td rowspan="4">300</td><td>3</td><td>1,60</td><td>2,40</td><td>3,20</td><td>4,00</td><td>5,00</td><td>6,00</td><td>6,50</td><td>7,5</td><td>8,5</td><td>10,5</td><td>12,0</td><td>13,5</td><td>15,0</td><td>17,0</td><td>19,5</td><td>23,5</td><td>3,25</td><td>0,56</td><td>2,4</td></tr>
<tr><td>29</td><td>5</td><td>1,80</td><td>2,80</td><td>3,85</td><td>4,85</td><td>6,00</td><td>7,00</td><td>8,00</td><td>9,0</td><td>10,5</td><td>12,5</td><td>15,0</td><td>17,0</td><td>19,0</td><td>21,0</td><td>24,0</td><td>29,0</td><td>4,05</td><td>0,45</td><td>3,4</td></tr>
<tr><td>30</td><td>8</td><td>2,10</td><td>3,40</td><td>4,70</td><td>6,00</td><td>7,50</td><td>9,00</td><td>10,00</td><td>11,5</td><td>13,5</td><td>16,0</td><td>19,0</td><td>21,5</td><td>24,0</td><td>26,5</td><td>30,5</td><td>37,0</td><td>5,00</td><td>0,35</td><td>4,1</td></tr>
<tr><td>31</td><td>12</td><td>2,90</td><td>5,00</td><td>7,00</td><td>9,00</td><td>11,5</td><td>13,50</td><td>16,00</td><td>18,0</td><td>21,0</td><td>25,0</td><td>29,5</td><td>34,0</td><td>38,0</td><td>42,0</td><td>48,5</td><td>59,0</td><td>8,50</td><td>0,22</td><td colspan="2" rowspan="5">48</td><td rowspan="5">57</td><td>4,9</td></tr>
<tr><td>32</td><td rowspan="4">380</td><td>3</td><td>1,70</td><td>2,75</td><td>3,75</td><td>4,75</td><td>6,00</td><td>7,00</td><td>8,00</td><td>9,0</td><td>10,5</td><td>12,5</td><td>15,0</td><td>17,0</td><td>19,0</td><td>21,0</td><td>24,0</td><td>29,0</td><td>4,05</td><td>0,56</td><td>2,4</td></tr>
<tr><td>33</td><td>5</td><td>1,95</td><td>3,20</td><td>4,45</td><td>5,50</td><td>7,00</td><td>8,50</td><td>9,50</td><td>11,0</td><td>13,0</td><td>15,0</td><td>18,0</td><td>20,5</td><td>23,0</td><td>25,5</td><td>29,0</td><td>35,5</td><td>5,00</td><td>0,45</td><td>3,4</td></tr>
<tr><td>34</td><td>8</td><td>2,35</td><td>3,95</td><td>5,50</td><td>7,00</td><td>9,00</td><td>10,50</td><td>12,00</td><td>14,0</td><td>16,5</td><td>19,5</td><td>23,0</td><td>26,0</td><td>29,0</td><td>32,5</td><td>37,5</td><td>45,5</td><td>6,50</td><td>0,35</td><td>4,1</td></tr>
<tr><td>35</td><td>12</td><td>3,25</td><td>5,50</td><td>8,00</td><td>10,5</td><td>13,5</td><td>16,00</td><td>18,5</td><td>21,0</td><td>24,5</td><td>29,5</td><td>34,5</td><td>39,5</td><td>44,5</td><td>49,5</td><td>57,0</td><td>70,0</td><td>10,50</td><td>0,22</td><td>4,9</td></tr>
<tr><td colspan="3">Индекс</td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="23%"><col width="32%"><col width="7%"><col width="5%"><col width="4%"><col width="5%"><col width="8%"><col width="2%"><col width="4%"><col width="10%"></colgroup>
<tr><td colspan="4">Неполное штучное время Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="4" rowspan="2">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Единичное и мелкосерийное производство</td><td colspan="6">Борштанги консольные Резцы с пластинками Т5К10</td></tr>
<tr><td colspan="4">Карта 22</td><td colspan="2">Лист 3</td></tr>
<tr><td colspan="10">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="5">Предела прочности и продолжительности обработки</td><td>Предел прочности сигма , ГПа в</td><td colspan="3">до 0,59</td><td colspan="2">0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td>Продолжительность обработки, мин.</td><td>до 10</td><td colspan="2">свыше 10</td><td colspan="2">-</td><td colspan="2">до 10</td><td>свыше 10</td></tr>
<tr><td rowspan="3">Коэффициент</td><td rowspan="3">0,9</td><td colspan="2" rowspan="3">0,8</td><td colspan="2"></td><td colspan="2" rowspan="3">1,1</td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td rowspan="2">Состояния обрабатываемой поверхности</td><td>Состояние обрабатываемой поверхности</td><td colspan="3">без корки и удара</td><td colspan="2">по корке и на удар</td><td colspan="2"></td><td></td></tr>
<tr><td>Коэффициент</td><td colspan="3">1,0</td><td colspan="2">1,2</td><td colspan="2"></td><td></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="4%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="26">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="26">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Борштанги двухопорные в Резцы из стали Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="23">Карта 23</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="19">10</td><td rowspan="4">120</td><td>3</td><td>2,70</td><td>3,50</td><td>4,30</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,0</td><td>9,0</td><td>10,0</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td>18,5</td><td>21,5</td><td>25,5</td><td>3,25</td><td>0,70</td><td colspan="2" rowspan="4">48</td><td rowspan="4">18</td><td>1,5</td></tr>
<tr><td>2</td><td>5</td><td>2,90</td><td>3,95</td><td>4,95</td><td>6,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>12,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td>21,0</td><td>23,0</td><td>26,5</td><td>31,5</td><td>4,10</td><td>0,56</td><td rowspan="2">1,7</td></tr>
<tr><td>3</td><td>8</td><td>3,20</td><td>4,45</td><td>6,0</td><td>7,0</td><td>9,0</td><td>10,0</td><td>11,5</td><td>12,5</td><td>14,5</td><td>17,0</td><td>20,0</td><td>22,5</td><td>25,0</td><td>27,5</td><td>31,5</td><td>37,5</td><td>5,0</td><td>0,45</td></tr>
<tr><td>4</td><td>12</td><td>3,60</td><td>5,50</td><td>7,00</td><td>8,5</td><td>10,5</td><td>12,5</td><td>14,0</td><td>15,5</td><td>18,0</td><td>21,0</td><td>25,0</td><td>28,0</td><td>31,5</td><td>34,5</td><td>40,0</td><td>48,0</td><td>6,5</td><td>0,35</td><td>2,3</td></tr>
<tr><td>5</td><td rowspan="4">150</td><td>3</td><td>2,85</td><td>3,85</td><td>4,85</td><td>6,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>12,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td>20,5</td><td>22,5</td><td>26,0</td><td>31,5</td><td>4,10</td><td>0,70</td><td colspan="2" rowspan="4">38</td><td rowspan="4">18</td><td>1,5</td></tr>
<tr><td>6</td><td>5</td><td>3,15</td><td>4,45</td><td>6,00</td><td>7,5</td><td>9,0</td><td>10,5</td><td>11,5</td><td>13,0</td><td>15,0</td><td>17,5</td><td>20,5</td><td>23,0</td><td>25,5</td><td>28,5</td><td>32,5</td><td>39,0</td><td>5,0</td><td>0,56</td><td>1,7</td></tr>
<tr><td>7</td><td>8</td><td>3,45</td><td>5,50</td><td>7,00</td><td>8,5</td><td>10,5</td><td>12,0</td><td>14,0</td><td>15,5</td><td>18,0</td><td>21,0</td><td>24,5</td><td>28,0</td><td>31,0</td><td>34,5</td><td>39,5</td><td>47,5</td><td>6,5</td><td>0,45</td><td>1,9</td></tr>
<tr><td>8</td><td>12</td><td>4,05</td><td>6,50</td><td>8,50</td><td>10,5</td><td>13,0</td><td>15,0</td><td>17,5</td><td>19,5</td><td>22,5</td><td>27,0</td><td>31,5</td><td>35,5</td><td>40,0</td><td>44,0</td><td>51,0</td><td>62,0</td><td>8,0</td><td>0,35</td><td>2,3</td></tr>
<tr><td>9</td><td rowspan="4">200</td><td>3</td><td>3,00</td><td>4,35</td><td>6,00</td><td>7,0</td><td>9,0</td><td>10,0</td><td>11,5</td><td>13,0</td><td>28,5</td><td>17,5</td><td>20,5</td><td>23,0</td><td>25,5</td><td>28,0</td><td>32,5</td><td>39,0</td><td>5,0</td><td>0,70</td><td colspan="2" rowspan="4">30</td><td rowspan="4">18</td><td>1,5</td></tr>
<tr><td>10</td><td>5</td><td>3,35</td><td>4,95</td><td>7,00</td><td>8,5</td><td>10,5</td><td>12,0</td><td>13,5</td><td>15,5</td><td>17,5</td><td>21,0</td><td>24,5</td><td>28,0</td><td>31,0</td><td>34,0</td><td>39,5</td><td>47,0</td><td>6,5</td><td>0,56</td><td>1,7</td></tr>
<tr><td>11</td><td>8</td><td>3,85</td><td>6,00</td><td>8,50</td><td>10,5</td><td>13,0</td><td>15,0</td><td>17,0</td><td>19,5</td><td>22,5</td><td>26,5</td><td>31,5</td><td>35,5</td><td>39,5</td><td>44,0</td><td>51,0</td><td>61,0</td><td>8,0</td><td>0,45</td><td>1,9</td></tr>
<tr><td>12</td><td>12</td><td>4,55</td><td>7,50</td><td>10,50</td><td>13,0</td><td>16,0</td><td>19,0</td><td>21,5</td><td>24,5</td><td>28,5</td><td>34,0</td><td>40,0</td><td>45,5</td><td>51,0</td><td>57,0</td><td>65,0</td><td>79,0</td><td>10,5</td><td>0,35</td><td>2,3</td></tr>
<tr><td>13</td><td rowspan="4">240</td><td>3</td><td>3,20</td><td>4,80</td><td>6,50</td><td>8,5</td><td>10,5</td><td>12,0</td><td>13,5</td><td>15,0</td><td>17,5</td><td>21,0</td><td>24,5</td><td>27,5</td><td>31,0</td><td>34,0</td><td>39,5</td><td>47,0</td><td>6,5</td><td>0,70</td><td colspan="2" rowspan="4">24</td><td rowspan="4">18</td><td>1,5</td></tr>
<tr><td>14</td><td>5</td><td>3,70</td><td>6,00</td><td>8,00</td><td>10,0</td><td>13,0</td><td>15,0</td><td>17,0</td><td>19,0</td><td>22,5</td><td>26,5</td><td>31,0</td><td>35,5</td><td>39,5</td><td>43,5</td><td>51,0</td><td>61,0</td><td>8,0</td><td>0,56</td><td>1,7</td></tr>
<tr><td>15</td><td>8</td><td>4,15</td><td>7,00</td><td>9,50</td><td>12,0</td><td>15,0</td><td>17,5</td><td>20,0</td><td>22,0</td><td>26,0</td><td>31,0</td><td>36,5</td><td>41,5</td><td>46,5</td><td>52,0</td><td>59,0</td><td>72,0</td><td>10,0</td><td>0,45</td><td>1,9</td></tr>
<tr><td>16</td><td>12</td><td>5,50</td><td>9,00</td><td>12,00</td><td>15,5</td><td>19,5</td><td>23,0</td><td>26,5</td><td>30,0</td><td>35,0</td><td>42,0</td><td>49,0</td><td>56,0</td><td>63,0</td><td>70,0</td><td>81,0</td><td>98,0</td><td>13,0</td><td>0,35</td><td>2,3</td></tr>
<tr><td>17</td><td rowspan="3">300</td><td>3</td><td>3,50</td><td>6,00</td><td>8,00</td><td>10,0</td><td>12,5</td><td>14,5</td><td>17,0</td><td>19,0</td><td>22,0</td><td>26,5</td><td>31,0</td><td>35,0</td><td>39,5</td><td>43,5</td><td>51,0</td><td>61,0</td><td>8,20</td><td>0,70</td><td colspan="2" rowspan="3">19</td><td rowspan="3">18</td><td>1,5</td></tr>
<tr><td>18</td><td>5</td><td>3,95</td><td>6,50</td><td>9,00</td><td>11,5</td><td>14,5</td><td>17,0</td><td>19,5</td><td>22,0</td><td>26,0</td><td>31,0</td><td>36,0</td><td>41,0</td><td>46,0</td><td>51,0</td><td>59,0</td><td>72,0</td><td>10,3</td><td>0,56</td><td>1,7</td></tr>
<tr><td>19</td><td>8</td><td>4,60</td><td>8,00</td><td>11,00</td><td>14,0</td><td>17,5</td><td>20,5</td><td>23,5</td><td>26,5</td><td>31,0</td><td>37,0</td><td>43,5</td><td>50,0</td><td>56,0</td><td>62,0</td><td>72,0</td><td>87,0</td><td>13,0</td><td>0,45</td><td>1,9</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="4%"><col width="6%"><col width="2%"><col width="1%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="1%"><col width="4%"><col width="5%"><col width="2%"><col width="2%"><col width="1%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="31">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="31">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Борштанги двухопорные в Резцы из стали Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="28">Карта 23</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td colspan="2">Глубина</td><td colspan="20">Длина обрабатываемой поверхности l, мм, до</td><td colspan="6">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td colspan="2">резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td colspan="2">175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td colspan="2">600</td><td>750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td colspan="2" rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td colspan="2">до</td><td colspan="20">Время на проход, мин.</td></tr>
<tr><td>20</td><td rowspan="9">10</td><td>300</td><td colspan="2">12</td><td>5,00</td><td>9,5</td><td>13,5</td><td>17,5</td><td>22,0</td><td>26,0</td><td colspan="2">29,5</td><td>33,5</td><td>39,5</td><td>47,5</td><td>56,0</td><td>64,0</td><td>71</td><td>79</td><td colspan="2">91</td><td>117</td><td colspan="2">16,5</td><td colspan="2">0,35</td><td colspan="2">19</td><td rowspan="9">18</td><td>2,3</td></tr>
<tr><td>21</td><td rowspan="4">380</td><td colspan="2">3</td><td>3,90</td><td>7,0</td><td>9,5</td><td>12,5</td><td>15,5</td><td>18,5</td><td colspan="2">21,0</td><td>23,5</td><td>28,0</td><td>33,5</td><td>39,0</td><td>44,5</td><td>50</td><td>56</td><td colspan="2">65</td><td>78</td><td colspan="2">10,5</td><td colspan="2">0,70</td><td colspan="2" rowspan="4">15</td><td>1,5</td></tr>
<tr><td>22</td><td colspan="2">5</td><td>4,60</td><td>8,5</td><td>11,5</td><td>15,0</td><td>19,0</td><td>22,5</td><td colspan="2">26,0</td><td>29,0</td><td>34,5</td><td>41,0</td><td>48,5</td><td>56,0</td><td>62</td><td>69</td><td colspan="2">80</td><td>97</td><td colspan="2">13,0</td><td colspan="2">0,56</td><td>1,7</td></tr>
<tr><td>23</td><td colspan="2">8</td><td>5,50</td><td>9,5</td><td>13,5</td><td>17,0</td><td>21,5</td><td>25,5</td><td colspan="2">29,5</td><td>33,5</td><td>39,0</td><td>47,0</td><td>56,0</td><td>63,0</td><td>71</td><td>79</td><td colspan="2">91</td><td>111</td><td colspan="2">16,0</td><td colspan="2">0,45</td><td>1,9</td></tr>
<tr><td>24</td><td colspan="2">12</td><td>7,00</td><td>12,5</td><td>18,0</td><td>23,5</td><td>29,5</td><td>35,0</td><td colspan="2">40,5</td><td>46,0</td><td>54,0</td><td>65,0</td><td>77,0</td><td>88,0</td><td>99</td><td>110</td><td colspan="2">126</td><td>154</td><td colspan="2">21,0</td><td colspan="2">0,35</td><td>2,3</td></tr>
<tr><td>25</td><td rowspan="4">480</td><td colspan="2">3</td><td>4,35</td><td>8,0</td><td>11,5</td><td>15,0</td><td>18,5</td><td>22,0</td><td colspan="2">25,5</td><td>29,0</td><td>34,0</td><td>41,0</td><td>48,0</td><td>55,0</td><td>62</td><td>69</td><td colspan="2">80</td><td>97</td><td colspan="2">13,0</td><td colspan="2">0,70</td><td colspan="2" rowspan="4">12</td><td>1,5</td></tr>
<tr><td>26</td><td colspan="2">5</td><td>4,95</td><td>9,0</td><td>13,0</td><td>17,0</td><td>21,5</td><td>25,0</td><td colspan="2">29,0</td><td>33,0</td><td>39,0</td><td>46,5</td><td>55,0</td><td>63,0</td><td>71</td><td>79</td><td colspan="2">91</td><td>110</td><td colspan="2">16,5</td><td colspan="2">0,56</td><td>1,7</td></tr>
<tr><td>27</td><td colspan="2">8</td><td>6,50</td><td>12,0</td><td>17,5</td><td>23,0</td><td>29,0</td><td>14,5</td><td colspan="2">40,0</td><td>45,5</td><td>54,0</td><td>65,0</td><td>76,0</td><td>87,0</td><td>98</td><td>109</td><td colspan="2">126</td><td>153</td><td colspan="2">20,0</td><td colspan="2">0,45</td><td>1,9</td></tr>
<tr><td>28</td><td colspan="2">12</td><td>8,50</td><td>15,0</td><td>22,0</td><td>29,0</td><td>36,0</td><td>43,0</td><td colspan="2">50,0</td><td>57,0</td><td>67,0</td><td>81,0</td><td>95,0</td><td>109,0</td><td>122</td><td>136</td><td colspan="2">157</td><td>191</td><td colspan="2">26,0</td><td colspan="2">0,35</td><td>2,3</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="2">п</td><td>р</td><td colspan="2">с</td><td colspan="6"></td></tr>
<tr><td colspan="31">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Группы стали, предела прочности и продолжительности</td><td colspan="17">Группа стали Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="10">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="4" rowspan="5">обработки</td><td colspan="14">Предел прочности сигма , ГПа до 0,59 0,59 - 0,74 в</td><td colspan="3">свыше 0,74</td><td colspan="3">до 0,59</td><td colspan="7">0,59 - 0,74 свыше 0,74</td></tr>
<tr><td colspan="10">Продолжительность обработки, мин. до 10</td><td colspan="4">свыше 10 -</td><td colspan="3">до 10 свыше 10</td><td colspan="3">до 10 свыше 10</td><td colspan="2">до 10</td><td colspan="5">свыше до свыше 10 10 10</td></tr>
<tr><td colspan="10" rowspan="3">Коэффициент 0,9</td><td colspan="4"></td><td colspan="3" rowspan="3">1,1 1,25</td><td colspan="3" rowspan="3">1,0 1,1</td><td colspan="2" rowspan="3">1,1</td><td colspan="5" rowspan="3">1,2 1,2 1,35</td></tr>
<tr><td colspan="2">0,8</td><td colspan="2">1,0</td></tr>
<tr><td colspan="4"></td></tr>
<tr><td colspan="4" rowspan="4">Состояния обрабатываемой поверхности</td><td colspan="20">Состояние обрабатываемой без корки и удара по корке поверхности</td><td colspan="7">на удар</td></tr>
<tr><td colspan="27"></td></tr>
<tr><td colspan="8">Коэффициент</td><td colspan="19">1,0 1,2</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="4%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="26">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="26">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Борштанги двухопорные в Резцы с пластинками Т5К10 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="23">Карта 24</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="16">10</td><td rowspan="4">120</td><td>3</td><td>2,40</td><td>2,65</td><td>2,90</td><td>3,15</td><td>3,85</td><td>4,10</td><td>4,40</td><td>4,65</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,0</td><td>8,5</td><td>9,5</td><td>11,0</td><td>1,05</td><td>0,70</td><td colspan="2" rowspan="4">150</td><td rowspan="4">56</td><td>2,7</td></tr>
<tr><td>2</td><td>5</td><td>2,45</td><td>2,75</td><td>3,10</td><td>3,45</td><td>4,20</td><td>4,50</td><td>4,85</td><td>5,50</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,0</td><td>9,5</td><td>11,0</td><td>12,5</td><td>1,30</td><td>0,56</td><td>3,8</td></tr>
<tr><td>3</td><td>8</td><td>2,55</td><td>2,95</td><td>3,35</td><td>3,75</td><td>4,60</td><td>5,00</td><td>5,50</td><td>6,00</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,0</td><td>13,0</td><td>15,0</td><td>1,60</td><td>0,45</td><td>5,4</td></tr>
<tr><td>4</td><td>12</td><td>2,65</td><td>3,20</td><td>3,70</td><td>4,25</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,00</td><td>8,0</td><td>9,0</td><td>10,5</td><td>11,5</td><td>12,5</td><td>13,5</td><td>15,5</td><td>18,0</td><td>2,10</td><td>0,35</td><td>6,5</td></tr>
<tr><td>5</td><td rowspan="4">150</td><td>3</td><td>2,40</td><td>2,75</td><td>3,05</td><td>3,40</td><td>4,15</td><td>4,50</td><td>4,80</td><td>5,50</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,0</td><td>9,0</td><td>9,5</td><td>11,0</td><td>12,5</td><td>1,30</td><td>0,70</td><td colspan="2" rowspan="4">120</td><td rowspan="4">56</td><td>2,7</td></tr>
<tr><td>6</td><td>5</td><td>2,50</td><td>2,90</td><td>3,30</td><td>3,75</td><td>4,55</td><td>5,00</td><td>5,50</td><td>6,00</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,0</td><td>13,0</td><td>15,0</td><td>1,60</td><td>0,56</td><td>3,8</td></tr>
<tr><td>7</td><td>8</td><td>2,60</td><td>3,10</td><td>3,60</td><td>4,15</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,00</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,5</td><td>15,0</td><td>17,5</td><td>2,00</td><td>0,45</td><td>5,4</td></tr>
<tr><td>8</td><td>12</td><td>2,80</td><td>3,45</td><td>4,10</td><td>4,75</td><td>6,00</td><td>6,50</td><td>7,50</td><td>8,00</td><td>9,0</td><td>10,5</td><td>12,0</td><td>13,5</td><td>14,5</td><td>9,5</td><td>18,5</td><td>21,5</td><td>2,60</td><td>0,35</td><td>6,5</td></tr>
<tr><td>9</td><td rowspan="4">190</td><td>3</td><td>2,45</td><td>2,90</td><td>3,30</td><td>3,70</td><td>4,55</td><td>4,95</td><td>5,50</td><td>6,00</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,0</td><td>13,0</td><td>15,0</td><td>1,65</td><td>0,70</td><td colspan="2" rowspan="4">96</td><td rowspan="4">57</td><td>2,7</td></tr>
<tr><td>10</td><td>5</td><td>2,55</td><td>3,10</td><td>3,60</td><td>4,10</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,00</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,0</td><td>15,0</td><td>17,5</td><td>2,05</td><td>0,56</td><td>3,8</td></tr>
<tr><td>11</td><td>8</td><td>2,70</td><td>3,35</td><td>4,00</td><td>4,60</td><td>6,00</td><td>6,50</td><td>7,00</td><td>8,00</td><td>9,0</td><td>10,0</td><td>12,0</td><td>13,0</td><td>14,5</td><td>15,5</td><td>18,0</td><td>21,0</td><td>2,55</td><td>0,45</td><td>5,4</td></tr>
<tr><td>12</td><td>12</td><td>2,90</td><td>3,70</td><td>4,50</td><td>5,50</td><td>7,00</td><td>7,50</td><td>8,50</td><td>9,00</td><td>10,5</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,5</td><td>19,0</td><td>22,0</td><td>26,0</td><td>3,25</td><td>0,35</td><td>6,5</td></tr>
<tr><td>13</td><td rowspan="4">240</td><td>3</td><td>2,55</td><td>3,05</td><td>3,60</td><td>4,10</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,00</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>12,5</td><td>13,5</td><td>15,5</td><td>18,0</td><td>2,10</td><td>0,70</td><td colspan="2" rowspan="4">75</td><td rowspan="4">56</td><td>2,7</td></tr>
<tr><td>14</td><td>5</td><td>2,65</td><td>3,30</td><td>3,95</td><td>4,65</td><td>6,00</td><td>6,50</td><td>7,00</td><td>8,00</td><td>9,0</td><td>10,0</td><td>12,0</td><td>13,0</td><td>14,5</td><td>16,0</td><td>18,0</td><td>21,5</td><td>2,60</td><td>0,56</td><td>3,8</td></tr>
<tr><td>15</td><td>8</td><td>2,85</td><td>3,65</td><td>4,45</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,50</td><td>9,00</td><td>10,5</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td>19,0</td><td>21,5</td><td>25,5</td><td>3,25</td><td>0,45</td><td>5,4</td></tr>
<tr><td>16</td><td>12</td><td>3,10</td><td>4,15</td><td>5,50</td><td>6,50</td><td>8,00</td><td>9,00</td><td>10,00</td><td>11,00</td><td>12,5</td><td>15,0</td><td>17,5</td><td>19,5</td><td>21,5</td><td>23,5</td><td>27,5</td><td>32,5</td><td>4,15</td><td>0,35</td><td>6,5</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="4%"><col width="6%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="1%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="1%"><col width="7%"><col width="4%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="29">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="29">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Борштанги двухопорные в Резцы с пластинками Т5К10 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="26">Карта 24</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td colspan="2">Глубина</td><td colspan="19">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td colspan="2">резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td colspan="2">175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td colspan="2">750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td colspan="2">до</td><td colspan="19">Время на проход, мин.</td></tr>
<tr><td>17</td><td rowspan="12">10</td><td rowspan="4">300</td><td colspan="2">3</td><td>2,60</td><td>3,25</td><td>3,90</td><td>4,55</td><td>6,0</td><td>6,5</td><td colspan="2">7,0</td><td>8,0</td><td>9,0</td><td>10,0</td><td>12,0</td><td>13,0</td><td>14,5</td><td>16,0</td><td>18,0</td><td colspan="2">21,5</td><td>2,60</td><td>0,70</td><td colspan="2" rowspan="4">60</td><td rowspan="4">57</td><td>2,7</td></tr>
<tr><td>18</td><td colspan="2">5</td><td>2,80</td><td>3,60</td><td>4,40</td><td>5,50</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td>9,0</td><td>10,5</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td>19,0</td><td>21,5</td><td colspan="2">25,5</td><td>3,25</td><td>0,56</td><td>3,8</td></tr>
<tr><td>19</td><td colspan="2">8</td><td>3,00</td><td>4,00</td><td>5,50</td><td>6,50</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td>11,0</td><td>12,5</td><td>14,5</td><td>17,0</td><td>19,0</td><td>21,0</td><td>23,0</td><td>26,5</td><td colspan="2">31,5</td><td>4,05</td><td>0,45</td><td>5,4</td></tr>
<tr><td>20</td><td colspan="2">12</td><td>3,35</td><td>4,65</td><td>6,00</td><td>7,50</td><td>9,0</td><td>10,5</td><td colspan="2">12,0</td><td>13,0</td><td>15,0</td><td>17,5</td><td>20,5</td><td>23,5</td><td>26,0</td><td>28,5</td><td>33,0</td><td colspan="2">39,5</td><td>5,50</td><td>0,35</td><td>6,5</td></tr>
<tr><td>21</td><td rowspan="4">380</td><td colspan="2">3</td><td>2,70</td><td>3,50</td><td>4,30</td><td>5,50</td><td>6,5</td><td>7,5</td><td colspan="2">8,0</td><td>9,0</td><td>10,0</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td>18,5</td><td>21,5</td><td colspan="2">25,5</td><td>3,25</td><td>0,70</td><td colspan="2" rowspan="4">48</td><td rowspan="4">57</td><td>2,7</td></tr>
<tr><td>22</td><td colspan="2">5</td><td>2,90</td><td>3,96</td><td>4,95</td><td>6,00</td><td>7,5</td><td>8,5</td><td colspan="2">9,5</td><td>10,5</td><td>12,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td>21,0</td><td>23,0</td><td>26,5</td><td colspan="2">31,5</td><td>4,10</td><td>0,56</td><td>3,8</td></tr>
<tr><td>23</td><td colspan="2">8</td><td>3,20</td><td>4,45</td><td>6,00</td><td>7,00</td><td>9,0</td><td>10,0</td><td colspan="2">11,5</td><td>12,5</td><td>14,5</td><td>17,0</td><td>20,0</td><td>22,5</td><td>25,0</td><td>27,5</td><td>31,5</td><td colspan="2">32,5</td><td>5,00</td><td>0,45</td><td>5,4</td></tr>
<tr><td>24</td><td colspan="2">12</td><td>3,60</td><td>5,50</td><td>7,00</td><td>8,50</td><td>10,5</td><td>12,5</td><td colspan="2">14,0</td><td>15,5</td><td>18,0</td><td>21,0</td><td>25,0</td><td>28,0</td><td>31,5</td><td>34,5</td><td>40,0</td><td colspan="2">48,0</td><td>6,50</td><td>0,35</td><td>6,5</td></tr>
<tr><td>25</td><td rowspan="4">480</td><td colspan="2">3</td><td>2,85</td><td>3,85</td><td>4,85</td><td>6,00</td><td>7,5</td><td>8,5</td><td colspan="2">9,5</td><td>10,5</td><td>12,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td>20,5</td><td>22,5</td><td>26,0</td><td colspan="2">31,5</td><td>4,10</td><td>0,70</td><td colspan="2" rowspan="4">38</td><td rowspan="4">57</td><td>2,7</td></tr>
<tr><td>26</td><td colspan="2">5</td><td>3,15</td><td>4,45</td><td>6,00</td><td>7,50</td><td>9,0</td><td>10,5</td><td colspan="2">11,5</td><td>13,0</td><td>15,0</td><td>17,5</td><td>20,5</td><td>23,0</td><td>25,5</td><td>28,5</td><td>32,5</td><td colspan="2">39,0</td><td>5,00</td><td>0,56</td><td>3,8</td></tr>
<tr><td>27</td><td colspan="2">8</td><td>3,45</td><td>5,50</td><td>7,00</td><td>8,50</td><td>10,5</td><td>12,0</td><td colspan="2">14,0</td><td>15,5</td><td>18,0</td><td>21,0</td><td>24,5</td><td>28,0</td><td>31,0</td><td>34,5</td><td>39,5</td><td colspan="2">47,5</td><td>6,50</td><td>0,45</td><td>5,4</td></tr>
<tr><td>28</td><td colspan="2">12</td><td>4,05</td><td>6,50</td><td>8,50</td><td>10,50</td><td>13,0</td><td>15,0</td><td colspan="2">17,5</td><td>19,5</td><td>22,5</td><td>27,0</td><td>31,5</td><td>35,5</td><td>40,0</td><td>44,0</td><td>51,0</td><td colspan="2">62,0</td><td>8,00</td><td>0,35</td><td>6,5</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td colspan="2">р</td><td>с</td><td colspan="5"></td></tr>
<tr><td colspan="29">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Предела прочности стали и продолжительности</td><td colspan="8">Предел прочности сигма , ГПа в</td><td colspan="6">до 0,59</td><td colspan="4">0,59 - 0,74</td><td colspan="7">свыше 0,74</td></tr>
<tr><td colspan="4" rowspan="4">обработки</td><td colspan="8">Продолжительность обработки, мин.</td><td colspan="3">до 10</td><td colspan="3">свыше 10</td><td colspan="4">-</td><td colspan="7">до 10 свыше 10</td></tr>
<tr><td colspan="8" rowspan="3">Коэффициент</td><td colspan="3" rowspan="3">0,9</td><td colspan="3" rowspan="3">0,8</td><td colspan="4"></td><td colspan="7" rowspan="3">1,1 1,25</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td colspan="4" rowspan="2">Состояния обрабатываемой поверхности</td><td colspan="8">Состояние обрабатываемой поверхности</td><td colspan="6">без корки и удара</td><td colspan="11">по корке и на удар</td></tr>
<tr><td colspan="8">Коэффициент</td><td colspan="6">1,0</td><td colspan="11">1,2</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="30">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 20, 1Т9 квалитет</td></tr>
<tr><td colspan="30">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Резцы из стали Р6М5 в</td></tr>
<tr><td colspan="30">Единичное и мелкосерийное производство Карта 25</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td colspan="2">Глубина</td><td colspan="21">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td colspan="2">резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td colspan="2">125</td><td>150</td><td>175</td><td colspan="2">200</td><td colspan="2">250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td colspan="2">до</td><td colspan="21">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">10</td><td>30</td><td colspan="2" rowspan="12">1</td><td>3,45</td><td>3,65</td><td>3,85</td><td>4,05</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td rowspan="12">0,35</td><td>380</td><td rowspan="12">37</td><td rowspan="12">1</td></tr>
<tr><td>2</td><td>48</td><td>3,50</td><td>3,80</td><td>4,15</td><td>4,50</td><td colspan="2">5,5</td><td>5,5</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>240</td></tr>
<tr><td>3</td><td>60</td><td>3,55</td><td>3,95</td><td>4,35</td><td>4,75</td><td colspan="2">6,0</td><td>6,0</td><td>6,5</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>190</td></tr>
<tr><td>4</td><td>75</td><td>3,60</td><td>4,15</td><td>4,65</td><td>5,50</td><td colspan="2">6,5</td><td>7,0</td><td>7,5</td><td colspan="2">8,0</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>150</td></tr>
<tr><td>5</td><td>96</td><td>3,70</td><td>4,35</td><td>5,00</td><td>6,00</td><td colspan="2">7,0</td><td>7,5</td><td>8,0</td><td colspan="2">9,0</td><td colspan="2">10,0</td><td>11,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>120</td></tr>
<tr><td>6</td><td>120</td><td>3,80</td><td>4,60</td><td>5,50</td><td>6,50</td><td colspan="2">7,5</td><td>8,5</td><td>9,0</td><td colspan="2">10,0</td><td colspan="2">11,0</td><td>13,0</td><td>15,0</td><td>16,5</td><td>18,5</td><td>20,0</td><td>23,0</td><td>27,0</td><td colspan="2">3,25</td><td>96</td></tr>
<tr><td>7</td><td>150</td><td>3,90</td><td>4,95</td><td>6,50</td><td>7,50</td><td colspan="2">8,5</td><td>10,0</td><td>11,0</td><td colspan="2">12,0</td><td colspan="2">13,5</td><td>15,5</td><td>18,5</td><td>20,5</td><td>22,5</td><td>24,5</td><td>28,5</td><td>34,0</td><td colspan="2">4,15</td><td>75</td></tr>
<tr><td>8</td><td>190</td><td>4,05</td><td>5,50</td><td>7,00</td><td>8,00</td><td colspan="2">10,0</td><td>11,0</td><td>12,5</td><td colspan="2">14,0</td><td colspan="2">16,0</td><td>18,5</td><td>21,5</td><td>24,0</td><td>27,0</td><td>29,5</td><td>34,0</td><td>40,5</td><td colspan="2">5,00</td><td>60</td></tr>
<tr><td>9</td><td>240</td><td>4,25</td><td>6,00</td><td>7,50</td><td>9,50</td><td colspan="2">11,5</td><td>13,0</td><td>14,5</td><td colspan="2">16,0</td><td colspan="2">18,5</td><td>22,0</td><td>25,5</td><td>29,0</td><td>32,0</td><td>35,5</td><td>41,0</td><td>49,0</td><td colspan="2">6,50</td><td>48</td></tr>
<tr><td>10</td><td>300</td><td>4,55</td><td>7,00</td><td>9,00</td><td>11,0</td><td colspan="2">13,5</td><td>15,5</td><td>18,0</td><td colspan="2">20,0</td><td colspan="2">23,0</td><td>27,5</td><td>32,0</td><td>36,5</td><td>40,5</td><td>45,0</td><td>52,0</td><td>63,0</td><td colspan="2">8,00</td><td>38</td></tr>
<tr><td>11</td><td>380</td><td>4,90</td><td>8,00</td><td>10,5</td><td>13,5</td><td colspan="2">16,5</td><td>19,0</td><td>22,0</td><td colspan="2">24,5</td><td colspan="2">29,0</td><td>34,0</td><td>40,5</td><td>46,0</td><td>52,0</td><td>57,0</td><td>66,0</td><td>80,0</td><td colspan="2">10,50</td><td>30</td></tr>
<tr><td>12</td><td>480</td><td>5,50</td><td>9,00</td><td>12,5</td><td>16,0</td><td colspan="2">19,5</td><td>23,0</td><td>26,5</td><td colspan="2">30,0</td><td colspan="2">35,0</td><td>42,0</td><td>49,5</td><td>56,0</td><td>63,0</td><td>70,0</td><td>81,0</td><td>98,0</td><td colspan="2">13,00</td><td>24</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td colspan="2">з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td colspan="2">с</td><td colspan="4"></td></tr>
<tr><td colspan="30">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Группы стали, предела прочности и продолжительности</td><td colspan="6">Группа стали</td><td colspan="11">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="9">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="4" rowspan="5">обработки</td><td colspan="6">Предел прочности сигма , в ГПа</td><td colspan="4">до 0,59</td><td colspan="4">0,59 - 0,74</td><td colspan="3">свыше 0,74</td><td colspan="3">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="6">Продолжительность обработки</td><td colspan="4">до 10 свыше 10</td><td colspan="4">-</td><td colspan="3">до 10 свыше 10</td><td colspan="3">до 10 свыше 10</td><td>до 10</td><td colspan="2">свыше 10</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="4" rowspan="3">0,9 0,8</td><td colspan="4"></td><td colspan="3" rowspan="3">1,1 1,25</td><td colspan="3"></td><td rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td colspan="3" rowspan="3">1,2 1,35</td></tr>
<tr><td colspan="2">1,0</td><td colspan="2"></td><td>1,0</td><td colspan="2">1,1</td></tr>
</table>


<a id="p101131"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету время по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="3%"><col width="4%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="4%"><col width="1%"><col width="2%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="29">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Ra 2,5, 1Т9 - 1Т8 квалитет</td></tr>
<tr><td colspan="29">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Резцы из стали Р6М5 в</td></tr>
<tr><td colspan="29">Единичное и мелкосерийное производство Карта 26</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="21">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td colspan="2">400</td><td>450</td><td colspan="2">500</td><td colspan="2">600</td><td>750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td colspan="21">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">10</td><td>30</td><td rowspan="12">1</td><td>4,85</td><td>5,5</td><td>5,5</td><td>6,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td rowspan="12">0,18</td><td>480</td><td rowspan="12">45</td><td rowspan="12"></td></tr>
<tr><td>2</td><td>48</td><td>4,85</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>7,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>380</td></tr>
<tr><td>3</td><td>60</td><td>4,90</td><td>5,5</td><td>6,0</td><td>6,5</td><td>8,0</td><td>8,5</td><td>9,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>300</td></tr>
<tr><td>4</td><td>75</td><td>5,00</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,5</td><td>9,0</td><td>9,5</td><td>10,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>240</td></tr>
<tr><td>5</td><td>96</td><td>5,50</td><td>6,0</td><td>7,0</td><td>7,5</td><td>9,0</td><td>10,0</td><td>10,5</td><td>11,5</td><td>13,0</td><td>14,5</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>190</td></tr>
<tr><td>6</td><td>120</td><td>5,50</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,0</td><td>14,5</td><td>16,5</td><td>19,5</td><td colspan="2">21,5</td><td>23,5</td><td colspan="2">25,5</td><td colspan="2">29,5</td><td>34,5</td><td colspan="2">4,0</td><td>150</td></tr>
<tr><td>7</td><td>150</td><td>5,50</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,0</td><td>12,5</td><td>13,5</td><td>15,0</td><td>16,5</td><td>19,0</td><td>22,5</td><td colspan="2">25,0</td><td>27,5</td><td colspan="2">30,0</td><td colspan="2">34,5</td><td>41,0</td><td colspan="2">5,0</td><td>120</td></tr>
<tr><td>8</td><td>190</td><td>6,00</td><td>7,5</td><td>9,0</td><td>10,5</td><td>13,0</td><td>14,5</td><td>16,0</td><td>17,5</td><td>20,0</td><td>23,5</td><td>27,5</td><td colspan="2">35,5</td><td>33,5</td><td colspan="2">37,0</td><td colspan="2">42,5</td><td>51,0</td><td colspan="2">6,5</td><td>96</td></tr>
<tr><td>9</td><td>240</td><td>6,00</td><td>8,0</td><td>10,5</td><td>12,5</td><td>15,0</td><td>17,0</td><td>19,5</td><td>21,5</td><td>24,5</td><td>29,0</td><td>34,0</td><td colspan="2">38,0</td><td>42,0</td><td colspan="2">46,5</td><td colspan="2">54,0</td><td>64,0</td><td colspan="2">8,0</td><td>75</td></tr>
<tr><td>10</td><td>300</td><td>6,50</td><td>9,0</td><td>11,5</td><td>14,0</td><td>17,0</td><td>19,5</td><td>22,0</td><td>24,5</td><td>28,0</td><td>33,0</td><td>39,0</td><td colspan="2">43,5</td><td>48,5</td><td colspan="2">54,0</td><td colspan="2">62,0</td><td>75,0</td><td colspan="2">10,0</td><td>60</td></tr>
<tr><td>11</td><td>380</td><td>6,50</td><td>9,5</td><td>12,5</td><td>15,5</td><td>19,5</td><td>22,5</td><td>25,5</td><td>28,5</td><td>33,0</td><td>39,0</td><td>48,0</td><td colspan="2">52,0</td><td>58,0</td><td colspan="2">65,0</td><td colspan="2">75,0</td><td>90,0</td><td colspan="2">12,5</td><td>48</td></tr>
<tr><td>12</td><td>480</td><td>7,00</td><td>11,0</td><td>15,0</td><td>19,0</td><td>23,5</td><td>27,5</td><td>31,0</td><td>35,0</td><td>41,0</td><td>49,0</td><td>58,0</td><td colspan="2">65,0</td><td>73,0</td><td colspan="2">81,0</td><td colspan="2">94,0</td><td>113,0</td><td colspan="2">16,0</td><td>38</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td colspan="2">м</td><td>н</td><td colspan="2">о</td><td colspan="2">п</td><td>р</td><td colspan="2">с</td><td colspan="4"></td></tr>
<tr><td colspan="29">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="29">Группы стали, Группа стали Углеродистые, хромистые, никелевые, Марганцовистые, хромомарганцовистые, предела прочности и хромоникелевые хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="23">обработки Предел прочности сигма , до 0,59 0,59 - 0,74 свыше 0,74 до 0,59 в ГПа</td><td colspan="3">0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="10">Продолжительность до 10 обработки, мин.</td><td colspan="6">свыше 10 - до 10</td><td colspan="5">свыше 10 до 10</td><td colspan="2">свыше 10</td><td>до 10</td><td colspan="2">свыше 10</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="10" rowspan="3">Коэффициент 0,9</td><td colspan="6"></td><td colspan="5"></td><td colspan="2" rowspan="3">1,1</td><td rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td colspan="3" rowspan="3">1,2 1,35</td></tr>
<tr><td colspan="2">0,8</td><td colspan="4">1,0 1,1</td><td colspan="3">1,25</td><td colspan="2">1,0</td></tr>
</table>


<a id="p101154"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету время по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="4%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="3%"><col width="5%"><col width="4%"><col width="4%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="29">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Ra 2,5, 1Т7 квалитет</td></tr>
<tr><td colspan="29">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Резцы из стали Р6М5 в</td></tr>
<tr><td colspan="29">Единичное и мелкосерийное производство Карта 27</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="21">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td colspan="2">400</td><td>450</td><td colspan="2">500</td><td colspan="2">600</td><td>750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td colspan="21">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">10</td><td>30</td><td rowspan="12">1,0</td><td>6,5</td><td>7,0</td><td>7,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td rowspan="12">0,1</td><td>750</td><td>70</td><td rowspan="12">1</td></tr>
<tr><td>2</td><td>48</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,0</td><td>9,0</td><td>9,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>600</td><td rowspan="11">90</td></tr>
<tr><td>3</td><td>60</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>480</td></tr>
<tr><td>4</td><td>75</td><td>6,5</td><td>7,5</td><td>8,0</td><td>9,0</td><td>10,5</td><td>11,0</td><td>12,0</td><td>12,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>380</td></tr>
<tr><td>5</td><td>96</td><td>7,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,5</td><td>12,0</td><td>13,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td>-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>300</td></tr>
<tr><td>6</td><td>120</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,5</td><td>13,5</td><td>14,5</td><td>15,5</td><td>17,5</td><td>19,5</td><td>22,5</td><td colspan="2">25,0</td><td>27,5</td><td colspan="2">29,5</td><td colspan="2">34,5</td><td>40,0</td><td colspan="2">4,55</td><td>240</td></tr>
<tr><td>7</td><td>150</td><td>7,0</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td>15,0</td><td>16,5</td><td>18,0</td><td>20,0</td><td>23,0</td><td>26,5</td><td colspan="2">29,5</td><td>32,5</td><td colspan="2">35,5</td><td colspan="2">41,0</td><td>48,5</td><td colspan="2">6,00</td><td>190</td></tr>
<tr><td>8</td><td>190</td><td>7,5</td><td>9,0</td><td>11,0</td><td>13,0</td><td>15,5</td><td>17,5</td><td>19,0</td><td>21,0</td><td>23,5</td><td>27,5</td><td>31,5</td><td colspan="2">35,5</td><td>39,0</td><td colspan="2">42,5</td><td colspan="2">49,5</td><td>59,0</td><td colspan="2">7,50</td><td>150</td></tr>
<tr><td>9</td><td>240</td><td>7,5</td><td>10,0</td><td>12,0</td><td>14,5</td><td>17,5</td><td>20,0</td><td>22,0</td><td>24,5</td><td>28,0</td><td>32,5</td><td>37,5</td><td colspan="2">42,0</td><td>47,0</td><td colspan="2">52,0</td><td colspan="2">60,0</td><td>71,0</td><td colspan="2">9,00</td><td>120</td></tr>
<tr><td>10</td><td>300</td><td>8,0</td><td>10,5</td><td>13,5</td><td>16,0</td><td>19,5</td><td>22,5</td><td>25,0</td><td>28,0</td><td>32,0</td><td>37,5</td><td>43,5</td><td colspan="2">49,0</td><td>55,0</td><td colspan="2">60,0</td><td colspan="2">70,0</td><td>84,0</td><td colspan="2">11,50</td><td>96</td></tr>
<tr><td>11</td><td>380</td><td>8,5</td><td>12,5</td><td>16,5</td><td>20,5</td><td>25,0</td><td>29,0</td><td>33,0</td><td>36,5</td><td>42,5</td><td>51,0</td><td>59,0</td><td colspan="2">67,0</td><td>75,0</td><td colspan="2">83,0</td><td colspan="2">96,0</td><td>115,0</td><td colspan="2">14,50</td><td>75</td></tr>
<tr><td>12</td><td>480</td><td>9,0</td><td>13,5</td><td>18,0</td><td>22,5</td><td>28,0</td><td>32,5</td><td>37,0</td><td>41,5</td><td>48,5</td><td>58,0</td><td>68,0</td><td colspan="2">77,0</td><td>86,0</td><td colspan="2">95,0</td><td colspan="2">110,0</td><td>133,0</td><td colspan="2">18,00</td><td>60</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td colspan="2">м</td><td>н</td><td colspan="2">о</td><td colspan="2">п</td><td>р</td><td colspan="2">с</td><td colspan="4"></td></tr>
<tr><td colspan="29">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Группы стали, предела прочности и продолжительности</td><td colspan="25">Группа стали Углеродистые, хромистые, никелевые, Марганцовистые, хромомарганцовистые, хромоникелевые хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="4" rowspan="5">обработки</td><td colspan="22">Предел прочности до 0,59 0,59 - 0,74 свыше 0,74 до 0,59 0,59 - 0,74 сигма , ГПа в</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="6">Продолжительность до 10 обработки, мин.</td><td colspan="6">свыше 10 - до 10</td><td colspan="5">свыше 10 до 10</td><td colspan="3">свыше 10 до 10</td><td colspan="2">свыше 10</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент 0,9</td><td colspan="6"></td><td colspan="5"></td><td colspan="3" rowspan="3">1,1 1,1</td><td colspan="2" rowspan="3">1,2</td><td colspan="3" rowspan="3">1,2 1,35</td></tr>
<tr><td colspan="2">0,8</td><td colspan="4">1,0 1,1</td><td colspan="3">1,25</td><td colspan="2">1,0</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="3%"><col width="5%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="30">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 20, 1Т9 квалитет</td></tr>
<tr><td colspan="30">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Резцы с пластинками Т15К6 в</td></tr>
<tr><td colspan="30">Единичное и мелкосерийное производство Карта 28</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="21">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td colspan="2">350</td><td>400</td><td>450</td><td colspan="2">500</td><td colspan="2">600</td><td>750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td colspan="21">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">10</td><td>30</td><td rowspan="12">1</td><td>3,35</td><td>3,45</td><td>3,55</td><td>3,65</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>0,25</td><td colspan="2">1200</td><td rowspan="12">113</td><td rowspan="12">1,99</td></tr>
<tr><td>2</td><td>48</td><td>3,35</td><td>3,50</td><td>3,6</td><td>3,70</td><td>4,15</td><td>4,30</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td rowspan="11">0,35</td><td colspan="2">750</td></tr>
<tr><td>3</td><td>60</td><td>3,40</td><td>3,50</td><td>3,65</td><td>3,80</td><td>4,30</td><td>4,40</td><td>4,55</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">600</td></tr>
<tr><td>4</td><td>75</td><td>3,40</td><td>3,55</td><td>3,75</td><td>3,90</td><td>4,45</td><td>4,60</td><td>4,75</td><td>4,95</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">480</td></tr>
<tr><td>5</td><td>96</td><td>3,45</td><td>3,65</td><td>3,85</td><td>4,05</td><td>4,65</td><td>4,85</td><td>5,50</td><td>6,00</td><td>6,0</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">380</td></tr>
<tr><td>6</td><td>120</td><td>3,45</td><td>3,70</td><td>4,00</td><td>4,25</td><td>4,90</td><td>5,50</td><td>5,50</td><td>6,00</td><td>6,5</td><td>7,0</td><td colspan="2">8,0</td><td>8,5</td><td>9,0</td><td colspan="2">9,5</td><td colspan="2">11,0</td><td>12,5</td><td colspan="2">1,05</td><td colspan="2">300</td></tr>
<tr><td>7</td><td>150</td><td>3,50</td><td>3,80</td><td>4,15</td><td>4,50</td><td>5,50</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,0</td><td>7,5</td><td colspan="2">9,0</td><td>9,5</td><td>10,0</td><td colspan="2">11,0</td><td colspan="2">12,5</td><td>14,0</td><td colspan="2">1,30</td><td colspan="2">240</td></tr>
<tr><td>8</td><td>190</td><td>3,55</td><td>3,95</td><td>4,35</td><td>4,75</td><td>6,00</td><td>6,00</td><td>6,50</td><td>7,00</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td>10,5</td><td>11,5</td><td colspan="2">12,5</td><td colspan="2">14,5</td><td>16,5</td><td colspan="2">1,65</td><td colspan="2">190</td></tr>
<tr><td>9</td><td>240</td><td>3,60</td><td>4,15</td><td>4,65</td><td>5,50</td><td>6,50</td><td>7,00</td><td>7,50</td><td>8,00</td><td>8,5</td><td>10,0</td><td colspan="2">11,5</td><td>12,5</td><td>13,5</td><td colspan="2">14,5</td><td colspan="2">17,0</td><td>19,5</td><td colspan="2">2,10</td><td colspan="2">150</td></tr>
<tr><td>10</td><td>300</td><td>3,70</td><td>4,35</td><td>5,00</td><td>6,00</td><td>7,00</td><td>7,50</td><td>8,00</td><td>9,00</td><td>10,0</td><td>11,0</td><td colspan="2">13,5</td><td>14,5</td><td>15,5</td><td colspan="2">17,0</td><td colspan="2">19,5</td><td>23,0</td><td colspan="2">2,60</td><td colspan="2">120</td></tr>
<tr><td>11</td><td>380</td><td>3,80</td><td>4,60</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,50</td><td>9,00</td><td>10,0</td><td>11,0</td><td>13,0</td><td colspan="2">15,0</td><td>16,5</td><td>18,5</td><td colspan="2">20,0</td><td colspan="2">23,0</td><td>27,0</td><td colspan="2">3,25</td><td colspan="2">96</td></tr>
<tr><td>12</td><td>480</td><td>3,90</td><td>4,95</td><td>6,50</td><td>7,50</td><td>8,50</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,5</td><td>15,5</td><td colspan="2">18,5</td><td>20,5</td><td>22,5</td><td colspan="2">24,5</td><td colspan="2">28,5</td><td>34,0</td><td colspan="2">4,20</td><td colspan="2">75</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="2">п</td><td>р</td><td colspan="2">с</td><td colspan="5"></td></tr>
<tr><td colspan="30">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="12">Предела прочности стали и Предел прочности сигма , ГПа продолжительности обработки в</td><td colspan="7">до 0,59</td><td colspan="5">0,59 - 0,74</td><td colspan="6">свыше 0,74</td></tr>
<tr><td colspan="12">Продолжительность обработки, мин.</td><td colspan="3">до 10</td><td colspan="4">свыше 10</td><td colspan="5">-</td><td colspan="3">до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td colspan="12" rowspan="3">Коэффициент</td><td colspan="3" rowspan="3">0,9</td><td colspan="4" rowspan="3">0,8</td><td colspan="5"></td><td colspan="3" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td colspan="3"></td></tr>
</table>


<a id="p101196"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету время по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="3%"><col width="4%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="1%"><col width="4%"><col width="4%"><col width="2%"><col width="1%"><col width="2%"><col width="1%"><col width="4%"><col width="3%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="30">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Ra 2,5, 1Т9 - 1Т8 квалитет</td></tr>
<tr><td colspan="30">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Резцы с пластинками Т15К6 в</td></tr>
<tr><td colspan="30">Единичное и мелкосерийное производство Карта 29</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="21">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td colspan="2">350</td><td>400</td><td>450</td><td colspan="2">500</td><td colspan="2">600</td><td>750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td colspan="21">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">10</td><td>30</td><td rowspan="12">1</td><td>4,70</td><td>4,80</td><td>4,95</td><td>5,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td rowspan="12">0,18</td><td colspan="2">1200</td><td>113</td><td rowspan="12">1</td></tr>
<tr><td>2</td><td>48</td><td>4,70</td><td>4,85</td><td>5,50</td><td>5,5</td><td>6,0</td><td>6,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">960</td><td rowspan="11">144</td></tr>
<tr><td>3</td><td>60</td><td>4,75</td><td>4,95</td><td>5,50</td><td>5,5</td><td>6,5</td><td>6,5</td><td>7,0</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">750</td></tr>
<tr><td>4</td><td>75</td><td>4,75</td><td>5,00</td><td>5,50</td><td>6,0</td><td>6,5</td><td>7,0</td><td>7,0</td><td>7,5</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">600</td></tr>
<tr><td>5</td><td>96</td><td>4,80</td><td>5,50</td><td>5,50</td><td>6,0</td><td>7,0</td><td>7,0</td><td>7,5</td><td>8,0</td><td>8,5</td><td>9,0</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td colspan="2">480</td></tr>
<tr><td>6</td><td>120</td><td>4,85</td><td>5,50</td><td>6,00</td><td>6,5</td><td>7,5</td><td>7,5</td><td>8,0</td><td>8,5</td><td>9,0</td><td>10,0</td><td colspan="2">11,5</td><td>12,5</td><td>13,0</td><td colspan="2">14,0</td><td colspan="2">16,0</td><td>18,0</td><td colspan="2">1,6</td><td colspan="2">380</td></tr>
<tr><td>7</td><td>150</td><td>4,90</td><td>5,50</td><td>6,00</td><td>6,5</td><td>8,0</td><td>8,5</td><td>9,0</td><td>9,5</td><td>10,0</td><td>11,0</td><td colspan="2">13,0</td><td>14,0</td><td>15,0</td><td colspan="2">16,0</td><td colspan="2">18,5</td><td>21,0</td><td colspan="2">2,0</td><td colspan="2">300</td></tr>
<tr><td>8</td><td>190</td><td>5,00</td><td>6,00</td><td>6,50</td><td>7,0</td><td>8,5</td><td>9,0</td><td>9,5</td><td>10,5</td><td>11,0</td><td>12,5</td><td colspan="2">14,5</td><td>16,0</td><td>17,0</td><td colspan="2">18,5</td><td colspan="2">21,0</td><td>24,5</td><td colspan="2">2,5</td><td colspan="2">240</td></tr>
<tr><td>9</td><td>240</td><td>5,50</td><td>6,00</td><td>7,00</td><td>7,5</td><td>9,0</td><td>10,0</td><td>10,5</td><td>11,5</td><td>13,0</td><td>14,5</td><td colspan="2">16,5</td><td>18,5</td><td>20,0</td><td colspan="2">21,5</td><td colspan="2">25,0</td><td>29,0</td><td colspan="2">3,2</td><td colspan="2">190</td></tr>
<tr><td>10</td><td>300</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,0</td><td>14,5</td><td>16,5</td><td colspan="2">19,5</td><td>21,5</td><td>23,5</td><td colspan="2">25,5</td><td colspan="2">29,5</td><td>34,5</td><td colspan="2">4,0</td><td colspan="2">150</td></tr>
<tr><td>11</td><td>380</td><td>5,50</td><td>7,00</td><td>8,00</td><td>9,5</td><td>11,0</td><td>12,5</td><td>13,5</td><td>15,0</td><td>16,5</td><td>19,0</td><td colspan="2">22,5</td><td>25,0</td><td>27,5</td><td colspan="2">30,0</td><td colspan="2">34,5</td><td>41,0</td><td colspan="2">5,0</td><td colspan="2">120</td></tr>
<tr><td>12</td><td>480</td><td>6,00</td><td>7,50</td><td>9,00</td><td>10,5</td><td>13,0</td><td>14,5</td><td>16,0</td><td>17,5</td><td>20,0</td><td>23,5</td><td colspan="2">27,5</td><td>30,5</td><td>33,5</td><td colspan="2">37,0</td><td colspan="2">42,5</td><td>51,0</td><td colspan="2">6,0</td><td colspan="2">96</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="2">п</td><td>р</td><td colspan="2">с</td><td colspan="5"></td></tr>
<tr><td colspan="30">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="12">Предела прочности стали и Предел прочности сигма , ГПа продолжительности обработки в</td><td colspan="7">до 0,59</td><td colspan="5">0,59 - 0,74</td><td colspan="6">свыше 0,74</td></tr>
<tr><td colspan="12">Продолжительность обработки, мин.</td><td colspan="3">до 10</td><td colspan="4">свыше 10</td><td colspan="5">-</td><td colspan="3">до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td colspan="12" rowspan="3">Коэффициент</td><td colspan="3" rowspan="3">0,9</td><td colspan="4" rowspan="3">0,8</td><td colspan="5"></td><td colspan="3" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td colspan="3"></td></tr>
</table>


<a id="p101218"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету время по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="4%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="28">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Ra 2,5, 1Т7 квалитет</td></tr>
<tr><td colspan="28">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Резцы с пластинками Т15К6 в</td></tr>
<tr><td colspan="28">Единичное и мелкосерийное производство Карта 30</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="20">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td colspan="2">500</td><td colspan="2">600</td><td>750</td><td colspan="2">Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td colspan="20">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">10</td><td>30</td><td rowspan="12">1</td><td>6,5</td><td>6,5</td><td>7,0</td><td>7,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td rowspan="12">0,18</td><td>1200</td><td>113</td><td rowspan="12">1</td></tr>
<tr><td>2</td><td>48</td><td>6,5</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>8,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>960</td><td rowspan="11">144</td></tr>
<tr><td>3</td><td>60</td><td>6,5</td><td>7,0</td><td>7,0</td><td>7,5</td><td>9,0</td><td>9,5</td><td>9,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>750</td></tr>
<tr><td>4</td><td>75</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,0</td><td>9,0</td><td>9,5</td><td>10,0</td><td>10,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>600</td></tr>
<tr><td>5</td><td>96</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,0</td><td>11,5</td><td>12,5</td><td>13,5</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">-</td><td>480</td></tr>
<tr><td>6</td><td>120</td><td>6,5</td><td>7,5</td><td>8,0</td><td>9,0</td><td>10,5</td><td>11,0</td><td>12,0</td><td>12,5</td><td>13,5</td><td>15,0</td><td>17,0</td><td>18,5</td><td>20,0</td><td colspan="2">21,5</td><td colspan="2">25,0</td><td>29,0</td><td colspan="2">2,85</td><td>380</td></tr>
<tr><td>7</td><td>150</td><td>7,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,5</td><td>12,0</td><td>13,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td>19,5</td><td>21,5</td><td>23,5</td><td colspan="2">25,0</td><td colspan="2">29,5</td><td>34,0</td><td colspan="2">3,65</td><td>300</td></tr>
<tr><td>8</td><td>190</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,5</td><td>13,5</td><td>14,5</td><td>15,5</td><td>17,5</td><td>19,5</td><td>22,5</td><td>25,0</td><td>27,5</td><td colspan="2">29,5</td><td colspan="2">34,5</td><td>40,0</td><td colspan="2">4,55</td><td>240</td></tr>
<tr><td>9</td><td>240</td><td>7,0</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td>15,0</td><td>16,0</td><td>16,5</td><td>20,0</td><td>23,0</td><td>26,5</td><td>29,5</td><td>32,5</td><td colspan="2">35,5</td><td colspan="2">41,0</td><td>48,5</td><td colspan="2">6,00</td><td>190</td></tr>
<tr><td>10</td><td>300</td><td>7,5</td><td>9,0</td><td>11,0</td><td>13,0</td><td>15,5</td><td>17,5</td><td>19,0</td><td>21,0</td><td>23,5</td><td>27,5</td><td>31,5</td><td>35,5</td><td>39,0</td><td colspan="2">42,5</td><td colspan="2">49,5</td><td>59,0</td><td colspan="2">7,50</td><td>150</td></tr>
<tr><td>11</td><td>380</td><td>7,5</td><td>10,0</td><td>12,0</td><td>14,5</td><td>17,5</td><td>20,0</td><td>22,0</td><td>24,5</td><td>28,0</td><td>32,5</td><td>37,5</td><td>42,0</td><td>47,0</td><td colspan="2">52,0</td><td colspan="2">60,0</td><td>71,0</td><td colspan="2">9,00</td><td>120</td></tr>
<tr><td>12</td><td>480</td><td>8,0</td><td>10,5</td><td>13,5</td><td>16,0</td><td>19,5</td><td>22,5</td><td>25,0</td><td>28,0</td><td>32,0</td><td>37,5</td><td>43,5</td><td>49,0</td><td>55,0</td><td colspan="2">60,0</td><td colspan="2">70,0</td><td>84,0</td><td colspan="2">11,00</td><td>96</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="2">п</td><td>р</td><td colspan="2">с</td><td colspan="4"></td></tr>
<tr><td colspan="28">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="5" rowspan="5">Предела прочности стали и продолжительности обработки</td><td colspan="13">Предел прочности сигма , ГПа до 0,59 в</td><td colspan="5">0,59 - 0,74</td><td colspan="5">свыше 0,74</td></tr>
<tr><td colspan="13">Продолжительность обработки, мин. до 10 свыше 10</td><td colspan="5">-</td><td colspan="2">до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td colspan="13" rowspan="3">Коэффициент 0,9 0,8</td><td colspan="5"></td><td colspan="2" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="7%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="10%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="13">Неполное штучное время Продольное и поперечное точение, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Единичное и мелкосерийное производство</td><td colspan="6">Суппорт планшайбы Резцы с пластинками Т5К10</td></tr>
<tr><td colspan="6">Карта 31 Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="11">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">резания t, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td colspan="2">250</td><td>Добавлять на каждые 100 мм свыше 250</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="11">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="21">10</td><td rowspan="3">120</td><td>3</td><td>1,40</td><td>1,7</td><td>2,20</td><td>2,50</td><td>3,1</td><td>3,4</td><td>3,7</td><td>4,0</td><td colspan="2">4,75</td><td>1,3</td><td>0,6</td><td rowspan="3">150</td><td rowspan="21">57</td><td>2,5</td></tr>
<tr><td>2</td><td>5</td><td>1,50</td><td>1,8</td><td>2,50</td><td>2,80</td><td>3,4</td><td>3,7</td><td>4,1</td><td>4,5</td><td colspan="2">5,5</td><td>1,5</td><td>0,5</td><td>3,5</td></tr>
<tr><td>3</td><td>8</td><td>1,60</td><td>2,1</td><td>2,70</td><td>3,15</td><td>3,8</td><td>4,3</td><td>4,7</td><td>5,5</td><td colspan="2">6,5</td><td>1,8</td><td>0,4</td><td>5,0</td></tr>
<tr><td>4</td><td rowspan="3">150</td><td>3</td><td>1,40</td><td>1,8</td><td>2,50</td><td>2,80</td><td>3,4</td><td>3,8</td><td>4,2</td><td>4,5</td><td colspan="2">5,5</td><td>1,5</td><td>0,6</td><td rowspan="3">120</td><td>2,5</td></tr>
<tr><td>5</td><td>5</td><td>1,50</td><td>2,0</td><td>2,70</td><td>3,20</td><td>3,8</td><td>4,3</td><td>4,7</td><td>5,5</td><td colspan="2">6,5</td><td>1,8</td><td>0,5</td><td>3,5</td></tr>
<tr><td>6</td><td>8</td><td>1,60</td><td>2,3</td><td>3,10</td><td>3,60</td><td>4,4</td><td>5,0</td><td>6,0</td><td>6,5</td><td colspan="2">7,5</td><td>2,3</td><td>0,4</td><td>5,0</td></tr>
<tr><td>7</td><td rowspan="3">190</td><td>3</td><td>1,50</td><td>2,0</td><td>2,70</td><td>3,20</td><td>3,9</td><td>4,4</td><td>4,9</td><td>5,5</td><td colspan="2">6,5</td><td>1,9</td><td>0,6</td><td rowspan="3">96</td><td>2,5</td></tr>
<tr><td>8</td><td>5</td><td>1,60</td><td>2,2</td><td>3,00</td><td>3,55</td><td>4,4</td><td>4,9</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td>2,3</td><td>0,5</td><td>3,5</td></tr>
<tr><td>9</td><td>8</td><td>1,80</td><td>2,5</td><td>3,50</td><td>4,15</td><td>5,5</td><td>6,0</td><td>7,0</td><td>7,5</td><td colspan="2">9,0</td><td>2,9</td><td>0,4</td><td>5,0</td></tr>
<tr><td>10</td><td rowspan="3">240</td><td>3</td><td>1,60</td><td>2,2</td><td>3,10</td><td>3,65</td><td>4,5</td><td>5,5</td><td>6,0</td><td>6,5</td><td colspan="2">8,0</td><td>2,5</td><td>0,6</td><td rowspan="3">75</td><td>2,5</td></tr>
<tr><td>11</td><td>5</td><td>1,70</td><td>2,5</td><td>3,45</td><td>4,20</td><td>5,5</td><td>6,0</td><td>7,0</td><td>7,5</td><td colspan="2">9,0</td><td>2,9</td><td>0,5</td><td>3,5</td></tr>
<tr><td>12</td><td>8</td><td>1,90</td><td>2,8</td><td>4,00</td><td>4,90</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10,5</td><td>3,7</td><td>0,4</td><td>5,0</td></tr>
<tr><td>13</td><td rowspan="3">300</td><td>3</td><td>1,70</td><td>2,5</td><td>3,50</td><td>4,20</td><td>5,5</td><td>6,0</td><td>7,0</td><td>7,5</td><td colspan="2">9,0</td><td>3,1</td><td>0,6</td><td rowspan="3">60</td><td>2,5</td></tr>
<tr><td>14</td><td>5</td><td>1,80</td><td>2,8</td><td>3,90</td><td>4,80</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10,0</td><td>3,6</td><td>0,5</td><td>3,5</td></tr>
<tr><td>15</td><td>8</td><td>2,10</td><td>3,2</td><td>4,60</td><td>6,00</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,0</td><td colspan="2">13,0</td><td>4,5</td><td>0,4</td><td>5,0</td></tr>
<tr><td>16</td><td rowspan="3">380</td><td>3</td><td>1,80</td><td>2,7</td><td>3,90</td><td>4,80</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">11,0</td><td>3,8</td><td>0,6</td><td rowspan="3">48</td><td>2,5</td></tr>
<tr><td>17</td><td>5</td><td>2,10</td><td>3,2</td><td>4,50</td><td>6,00</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,0</td><td colspan="2">12,5</td><td>4,5</td><td>0,5</td><td>3,5</td></tr>
<tr><td>18</td><td>8</td><td>2,35</td><td>3,8</td><td>5,50</td><td>7,00</td><td>9,0</td><td>10,0</td><td>11,5</td><td>13,0</td><td colspan="2">15,5</td><td>5,7</td><td>0,4</td><td>5,0</td></tr>
<tr><td>19</td><td rowspan="3">480</td><td>3</td><td>1,90</td><td>3,2</td><td>4,50</td><td>6,00</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,0</td><td colspan="2">13,0</td><td>4,8</td><td>0,6</td><td rowspan="3">38</td><td>2,5</td></tr>
<tr><td>20</td><td>5</td><td>2,30</td><td>3,7</td><td>5,50</td><td>7,00</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,0</td><td colspan="2">15,5</td><td>6,0</td><td>0,5</td><td>3,5</td></tr>
<tr><td>21</td><td>8</td><td>2,60</td><td>4,5</td><td>6,50</td><td>8,50</td><td>10,0</td><td>12,5</td><td>14,5</td><td>16,0</td><td colspan="2">19,0</td><td>7,0</td><td>0,4</td><td>5,0</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td colspan="4"></td></tr>
</table>



```text
┌──────────────────────────────────────────────────────────────────┬──────────────────────────────┐
│Неполное штучное время                                            │Горизонтально-расточные станки│
│Продольное и поперечное точение, Rz 80, 1Т14 - 1Т12 квалитет      ├──────────────────────────────┤
│Сталь конструкционная углеродистая, сигма  = 0,59 - 0,74 ГПа      │      Суппорт планшайбы       │
│                                         в                        │  Резцы с пластинками Т5К10   │
│Единичное и мелкосерийное производство                            ├────────────────┬─────────────┤
│                                                                  │    Карта 31    │   Лист 2    │
├───┬──────┬───────┬────┬──────────────────────────────────────────┴───────────┬────┴─────────────┤
│N  │Мощ-  │Диаметр│Глу-│      Длина обрабатываемой поверхности l, мм, до      │  Режимы резания  │
│по-│ность │обраба-│бина├────┬────┬────┬────┬────┬────┬────┬────┬────┬─────────┼───┬────┬────┬────┤
│зи-│станка│тывае- │ре- │ 25 │ 50 │ 75 │100 │125 │150 │175 │200 │250 │Добавлять│S ,│ n, │ v, │N , │
│ции│N ,   │мого   │за- │    │    │    │    │    │    │    │    │    │на каждые│ о │об./│ м/ │ р  │
│   │ д    │отвер- │ния │    │    │    │    │    │    │    │    │    │ 100 мм  │мм/│мин.│мин.│кВт,│
│   │кВт,  │стия D,│t,  │    │    │    │    │    │    │    │    │    │свыше 250│об.│    │    │ до │
│   │до    │мм, до │мм, ├────┴────┴────┴────┴────┴────┴────┴────┴────┴─────────┤   │    │    │    │
│   │      │       │до  │                Время на проход, мин.                 │   │    │    │    │
├───┼──────┼───────┼────┼────┬────┬────┬────┬────┬────┬────┬────┬────┬─────────┼───┼────┼────┼────┤
│22 │10    │600    │3   │2,2 │3,7 │5,5 │7,0 │9,0 │10  │12  │13  │16  │6,0      │0,6│30  │57  │2,5 │
├───┤      │       ├────┼────┼────┼────┼────┼────┼────┼────┼────┼────┼─────────┼───┤    │    ├────┤
│23 │      │       │5   │2,5 │4,3 │6,5 │8,5 │10,0│12  │14  │16  │19  │7,5      │0,5│    │    │3,5 │
├───┤      │       ├────┼────┼────┼────┼────┼────┼────┼────┼────┼────┼─────────┼───┤    │    ├────┤
│24 │      │       │8   │8,0 │5,5 │8,0 │10,0│13,0│15  │17  │19  │23  │9,0      │0,4│    │    │5,0 │
├───┴──────┴───────┴────┼────┼────┼────┼────┼────┼────┼────┼────┼────┼─────────┼───┴────┴────┴────┤
│        Индекс         │ а  │ б  │ в  │ г  │ д  │ е  │ ж  │ з  │ и  │    к    │                  │
├───────────────────────┴────┴────┴────┴────┴────┴────┴────┴────┴────┴─────────┴──────────────────┤
│   Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:   │
├───────────────────┬─────────────────────────────────┬────────────────┬───────────┬──────────────┤
│Предела прочности  │Предел прочности сигма , ГПа     │    до 0,59     │0,59 - 0,74│  свыше 0,74  │
│стали и            │                      в          │                │           │              │
│продолжительности  ├─────────────────────────────────┼───────┬────────┼───────────┼─────┬────────┤
│обработки          │Продолжительность обработки, мин.│до 10  │свыше 10│-          │до 10│свыше 10│
│                   ├─────────────────────────────────┼───────┼────────┼───────────┼─────┼────────┤
│                   │                                 │       │        │┌───┐      │     │        │
│                   │Коэффициент                      │0,9    │0,8     ││1,0│      │1,1  │1,25    │
│                   │                                 │       │        │└───┘      │     │        │
├───────────────────┼─────────────────────────────────┼───────┴────────┼───────────┴─────┴────────┤
│Состояния          │Состояние обрабатываемой         │без корки и     │по корке и на удар        │
│обрабатываемой     │поверхности                      │удара           │                          │
│поверхности        ├─────────────────────────────────┼────────────────┼──────────────────────────┤
│                   │                                 │┌───┐           │                          │
│                   │Коэффициент                      ││1,0│           │1,2                       │
│                   │                                 │└───┘           │                          │
├───────────────────┼─────────────────────────────────┼────────────────┴──────────────────────────┤
│Вида обработки     │Продольное и поперечное точение  │Растачивание                               │
│                   ├─────────────────────────────────┴───────────────────────────────────────────┤
│                   │                                 Коэффициент                                 │
│                   ├─────────────────────────────────┬───────────────────────────────────────────┤
│                   │┌───┐                            │                                           │
│                   ││1,0│                            │1,06                                       │
│                   │└───┘                            │                                           │
└───────────────────┴─────────────────────────────────┴───────────────────────────────────────────┘
```



<table>
<colgroup><col width="4%"><col width="7%"><col width="8%"><col width="3%"><col width="2%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="6%"><col width="5%"><col width="3%"><col width="5%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="23">Неполное штучное время Горизонтально-расточные станки Продольное и поперечное точение, Rz 40, 1Т11 квалитет</td></tr>
<tr><td colspan="23">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Суппорт планшайбы в Резцы с пластинками Т15К6 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="23">Карта 32</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td colspan="2">Глубина</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td colspan="2">резания t, мм,</td><td colspan="2">25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td colspan="2">175</td><td>200</td><td>250</td><td colspan="3">Добавлять на каждые 100 мм свыше 250</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="2">до</td><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="8">10</td><td>120</td><td colspan="2" rowspan="8">1</td><td colspan="2">1,70</td><td>1,90</td><td>2,20</td><td>2,40</td><td>2,85</td><td>3,05</td><td colspan="2">3,25</td><td>3,45</td><td>4,1</td><td colspan="3">0,80</td><td rowspan="8">0,35</td><td>380</td><td rowspan="8">142</td><td rowspan="8">2,22</td></tr>
<tr><td>2</td><td>150</td><td colspan="2">1,70</td><td>1,95</td><td>2,35</td><td>2,60</td><td>3,10</td><td>3,35</td><td colspan="2">3,60</td><td>3,85</td><td>4,6</td><td colspan="3">1,05</td><td>300</td></tr>
<tr><td>3</td><td>190</td><td colspan="2">1,75</td><td>2,05</td><td>2,50</td><td>2,85</td><td>3,40</td><td>3,70</td><td colspan="2">4,05</td><td>4,35</td><td>5,5</td><td colspan="3">1,30</td><td>240</td></tr>
<tr><td>4</td><td>240</td><td colspan="2">1,80</td><td>2,20</td><td>2,75</td><td>3,15</td><td>3,80</td><td>4,20</td><td colspan="2">4,60</td><td>5,50</td><td>6,0</td><td colspan="3">1,65</td><td>190</td></tr>
<tr><td>5</td><td>300</td><td colspan="2">1,85</td><td>2,40</td><td>3,05</td><td>3,55</td><td>4,30</td><td>4,80</td><td colspan="2">5,50</td><td>6,00</td><td>7,0</td><td colspan="3">2,10</td><td>150</td></tr>
<tr><td>6</td><td>380</td><td colspan="2">1,95</td><td>2,60</td><td>3,35</td><td>4,00</td><td>4,85</td><td>5,50</td><td colspan="2">6,50</td><td>7,00</td><td>8,5</td><td colspan="3">2,60</td><td>120</td></tr>
<tr><td>7</td><td>480</td><td colspan="2">2,00</td><td>2,85</td><td>3,75</td><td>4,55</td><td>6,00</td><td>6,50</td><td colspan="2">7,50</td><td>8,00</td><td>10,0</td><td colspan="3">3,25</td><td>96</td></tr>
<tr><td>8</td><td>600</td><td colspan="2">2,15</td><td>3,20</td><td>4,40</td><td>5,50</td><td>7,00</td><td>8,00</td><td colspan="2">9,00</td><td>10,00</td><td>12,0</td><td colspan="3">4,15</td><td>75</td></tr>
<tr><td colspan="5">Индекс</td><td colspan="2">а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td colspan="3">к</td><td colspan="4"></td></tr>
<tr><td colspan="23">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Предела прочности стали и продолжительности</td><td colspan="9">Предел прочности сигма , ГПа в</td><td colspan="4">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="4" rowspan="4">обработки</td><td colspan="9">Продолжительность обработки, мин.</td><td colspan="4">до 10 свыше 10</td><td colspan="3">-</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="9" rowspan="3">Коэффициент</td><td colspan="4" rowspan="3">0,9 0,8</td><td colspan="3"></td><td colspan="3" rowspan="3">1,1 1,25</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="4" rowspan="5">Вида обработки</td><td colspan="9">Продольное и поперечное точение</td><td colspan="10">Растачивание</td></tr>
<tr><td colspan="19">Коэффициент</td></tr>
<tr><td colspan="9"></td><td colspan="10" rowspan="3">1,06</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7"></td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="7%"><col width="8%"><col width="3%"><col width="2%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="5%"><col width="2%"><col width="3%"><col width="5%"><col width="5%"><col width="3%"><col width="5%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="23">Неполное штучное время Горизонтально-расточные станки Продольное и поперечное точение, Ra 2,5, 1Т9 - 1Т8 квалитет</td></tr>
<tr><td colspan="23">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Суппорт планшайбы в Резцы с пластинками Т15К6 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="23">Карта 33</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td colspan="2">Глубина</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td colspan="2">резания t, мм,</td><td colspan="2">25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td colspan="2">175</td><td>200</td><td>250</td><td colspan="3">Добавлять на каждые 100 мм свыше 250</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="2">до</td><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="8">10</td><td>120</td><td colspan="2" rowspan="8">1</td><td colspan="2">2,80</td><td>3,10</td><td>3,50</td><td>3,80</td><td>4,40</td><td>4,7</td><td colspan="2">4,95</td><td>5,5</td><td>6,0</td><td colspan="3">1,10</td><td rowspan="8">0,2</td><td>480</td><td rowspan="8">180</td><td rowspan="8">1</td></tr>
<tr><td>2</td><td>150</td><td colspan="2">2,85</td><td>3,20</td><td>3,70</td><td>4,05</td><td>4,75</td><td>5,5</td><td colspan="2">5,5</td><td>6,0</td><td>7,0</td><td colspan="3">1,45</td><td>380</td></tr>
<tr><td>3</td><td>190</td><td colspan="2">2,90</td><td>3,35</td><td>3,95</td><td>4,40</td><td>5,50</td><td>6,0</td><td colspan="2">6,5</td><td>7,0</td><td>7,5</td><td colspan="3">1,80</td><td>300</td></tr>
<tr><td>4</td><td>240</td><td colspan="2">3,00</td><td>3,55</td><td>4,25</td><td>4,80</td><td>6,00</td><td>6,5</td><td colspan="2">7,0</td><td>7,5</td><td>8,5</td><td colspan="3">2,25</td><td>240</td></tr>
<tr><td>5</td><td>300</td><td colspan="2">3,05</td><td>3,80</td><td>4,60</td><td>5,50</td><td>6,50</td><td>7,5</td><td colspan="2">8,0</td><td>9,0</td><td>10,0</td><td colspan="3">2,95</td><td>190</td></tr>
<tr><td>6</td><td>380</td><td colspan="2">3,20</td><td>4,10</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,5</td><td colspan="2">9,5</td><td>10,0</td><td>12,0</td><td colspan="3">3,65</td><td>150</td></tr>
<tr><td>7</td><td>480</td><td colspan="2">3,30</td><td>4,45</td><td>6,00</td><td>7,00</td><td>8,50</td><td>9,5</td><td colspan="2">11,0</td><td>12,0</td><td>14,0</td><td colspan="3">4,55</td><td>120</td></tr>
<tr><td>8</td><td>600</td><td colspan="2">3,50</td><td>4,95</td><td>6,50</td><td>8,00</td><td>10,00</td><td>11,5</td><td colspan="2">13,0</td><td>14,0</td><td>16,5</td><td colspan="3">5,50</td><td>96</td></tr>
<tr><td colspan="5">Индекс</td><td colspan="2">а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td colspan="3">к</td><td colspan="4"></td></tr>
<tr><td colspan="23">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Предела прочности стали и продолжительности</td><td colspan="9">Предел прочности сигма , ГПа в</td><td colspan="4">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="4" rowspan="4">обработки</td><td colspan="9">Продолжительность обработки, мин.</td><td colspan="4">до 10 свыше 10</td><td colspan="3">-</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="9" rowspan="3">Коэффициент</td><td colspan="4" rowspan="3">0,9 0,8</td><td colspan="3"></td><td colspan="3" rowspan="3">1,1 1,25</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="4" rowspan="5">Вида обработки</td><td colspan="9">Продольное и поперечное точение</td><td colspan="10">Растачивание</td></tr>
<tr><td colspan="19">Коэффициент</td></tr>
<tr><td colspan="9"></td><td colspan="10" rowspan="3">1,06</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7"></td></tr>
</table>


<a id="p101315"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету время по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="4%"><col width="7%"><col width="8%"><col width="3%"><col width="2%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="5%"><col width="5%"><col width="3%"><col width="5%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="23">Неполное штучное время Горизонтально-расточные станки Продольное и поперечное точение, Ra 1,25, 1Т7 квалитет</td></tr>
<tr><td colspan="23">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Резцы с пластинками Т15К6 в</td></tr>
<tr><td colspan="23">Единичное и мелкосерийное производство Карта 34</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td colspan="2">Глубина</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td colspan="2">резания t, мм,</td><td colspan="2">25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td colspan="2">175</td><td>200</td><td>250</td><td colspan="3">Добавлять на каждые 100 мм свыше 250</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="2">до</td><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="8">10</td><td>120</td><td colspan="2" rowspan="8">1</td><td colspan="2">3,90</td><td>4,40</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td colspan="2">7,5</td><td>8,0</td><td>9,0</td><td colspan="3">1,90</td><td rowspan="8">0,12</td><td>480</td><td rowspan="8">180</td><td rowspan="8">1,9</td></tr>
<tr><td>2</td><td>150</td><td colspan="2">4,00</td><td>4,60</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td colspan="2">8,5</td><td>9,0</td><td>10,5</td><td colspan="3">2,40</td><td>380</td></tr>
<tr><td>3</td><td>190</td><td colspan="2">4,10</td><td>4,85</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">9,5</td><td>10,5</td><td>12,0</td><td colspan="3">3,05</td><td>300</td></tr>
<tr><td>4</td><td>240</td><td colspan="2">4,20</td><td>5,50</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,0</td><td colspan="2">10,5</td><td>11,5</td><td>13,5</td><td colspan="3">3,80</td><td>240</td></tr>
<tr><td>5</td><td>300</td><td colspan="2">4,35</td><td>5,50</td><td>7,0</td><td>8,5</td><td>10,0</td><td>11,0</td><td colspan="2">12,5</td><td>13,5</td><td>16,0</td><td colspan="3">4,80</td><td>190</td></tr>
<tr><td>6</td><td>380</td><td colspan="2">4,50</td><td>6,50</td><td>8,0</td><td>9,5</td><td>11,5</td><td>13,0</td><td colspan="2">14,5</td><td>16,0</td><td>19,0</td><td colspan="3">6,00</td><td>150</td></tr>
<tr><td>7</td><td>480</td><td colspan="2">4,75</td><td>7,00</td><td>9,0</td><td>11,0</td><td>13,5</td><td>15,5</td><td colspan="2">17,5</td><td>19,5</td><td>22,5</td><td colspan="3">7,50</td><td>120</td></tr>
<tr><td>8</td><td>600</td><td colspan="2">5,50</td><td>8,00</td><td>10,5</td><td>13,0</td><td>16,0</td><td>18,5</td><td colspan="2">21,0</td><td>23,5</td><td>27,5</td><td colspan="3">9,50</td><td>96</td></tr>
<tr><td colspan="5">Индекс</td><td colspan="2">а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td colspan="3">к</td><td colspan="4"></td></tr>
<tr><td colspan="23">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4" rowspan="4">Предела прочности стали</td><td colspan="9">Предел прочности сигма , ГПа в</td><td colspan="4">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="9" rowspan="3">Коэффициент</td><td colspan="4" rowspan="3">0,8</td><td colspan="3"></td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="4" rowspan="5">Вида обработки</td><td colspan="9">Продольное и поперечное точение</td><td colspan="10">Растачивание</td></tr>
<tr><td colspan="19">Коэффициент</td></tr>
<tr><td colspan="9"></td><td colspan="10" rowspan="3">1,06</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7"></td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="5%"><col width="9%"><col width="7%"><col width="4%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="7%"><col width="4%"><col width="3%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="4%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="11">Неполное штучное время Прорезка канавок</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="11">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="8">Суппорт планшайбы Резцы из стали Р6М5</td></tr>
<tr><td colspan="11">Единичное и мелкосерийное производство</td><td colspan="8">Карта 35</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="2">Диаметр обрабатываемой поверхности</td><td colspan="2">Ширина резца</td><td colspan="9">Глубина канавки l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td colspan="2" rowspan="2">В, мм</td><td>3</td><td colspan="2">4,5</td><td>6</td><td>8</td><td colspan="2">10</td><td>12</td><td>15</td><td colspan="2" rowspan="2">S , о мм/об.</td><td colspan="2" rowspan="2">v, м/мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="2">D, мм, до</td><td colspan="9">Время на поверхность, мин.</td></tr>
<tr><td>1</td><td colspan="2">50</td><td colspan="2">3 - 5</td><td>2,8</td><td colspan="2">2,9</td><td>3,0</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2" rowspan="4">0,07</td><td colspan="2">25,0</td><td rowspan="10">1</td></tr>
<tr><td>2</td><td colspan="2">75</td><td colspan="2">3 - 5</td><td>3,1</td><td colspan="2">3,3</td><td>3,5</td><td>3,7</td><td colspan="2">4,0</td><td>-</td><td>-</td><td colspan="2">23,5</td></tr>
<tr><td>3</td><td colspan="2">100</td><td colspan="2">5 - 8</td><td>3,3</td><td colspan="2">3,5</td><td>3,7</td><td>4,0</td><td colspan="2">4,5</td><td>5,0</td><td>5,5</td><td colspan="2">25,0</td></tr>
<tr><td>4</td><td colspan="2">125</td><td colspan="2">5 - 8</td><td>3,7</td><td colspan="2">3,9</td><td>4,2</td><td>4,7</td><td colspan="2">5,0</td><td>5,5</td><td>6,0</td><td colspan="2" rowspan="2">23,5 - 22,0</td></tr>
<tr><td>5</td><td colspan="2">150</td><td colspan="2">8</td><td>4,0</td><td colspan="2">4,4</td><td>4,7</td><td>5,5</td><td colspan="2">6,0</td><td>6,5</td><td>7,0</td><td colspan="2">0,07 - 0,09</td></tr>
<tr><td>6</td><td colspan="2">200</td><td colspan="2" rowspan="5">10 - 12</td><td>4,5</td><td colspan="2">4,8</td><td>5,2</td><td>6,0</td><td colspan="2">7,0</td><td>7,5</td><td>8,5</td><td colspan="2" rowspan="2">0,09</td><td colspan="2">20,0</td></tr>
<tr><td>7</td><td colspan="2">300</td><td>5,0</td><td colspan="2">5,5</td><td>6,0</td><td>7,0</td><td colspan="2">8,0</td><td>9,0</td><td>10,0</td><td colspan="2">19,5 - 23,5</td></tr>
<tr><td>8</td><td colspan="2">400</td><td>6,0</td><td colspan="2">6,5</td><td>7,0</td><td>8,5</td><td colspan="2">9,5</td><td>10,5</td><td>12,0</td><td colspan="2">0,09 - 0,12</td><td colspan="2">22,0 - 19,0</td></tr>
<tr><td>9</td><td colspan="2">500</td><td>6,5</td><td colspan="2">7,5</td><td>8,0</td><td>9,5</td><td colspan="2">11,0</td><td>12,5</td><td>14,0</td><td colspan="2" rowspan="2">0,12</td><td colspan="2">17,5 - 19,5</td></tr>
<tr><td>10</td><td colspan="2">500</td><td>7,5</td><td colspan="2">8,5</td><td>9,5</td><td>11,5</td><td colspan="2">13,0</td><td>15,0</td><td>17,0</td><td colspan="2">17,0 - 19,0</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td colspan="5"></td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="6">Группы стали, предела прочности и продолжительности обработки</td><td colspan="2">Группа стали</td><td colspan="8">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="7">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="2">Предел прочности сигма , в ГПа</td><td colspan="3">до 0,59</td><td colspan="5">0,59 - свыше 0,74 0,74</td><td colspan="5">до 0,59 0,59 - 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td colspan="2">Продолжительность обработки, мин.</td><td colspan="3">до свы- 10 ше 10</td><td colspan="3">- до 10</td><td colspan="2">свыше 10</td><td colspan="3">до 10 свы- до ше 10 10</td><td colspan="2">свыше 10</td><td>до 10</td><td>свыше 10</td></tr>
<tr><td colspan="2" rowspan="3">Коэффициент</td><td colspan="3" rowspan="3">0,9 0,8</td><td colspan="3"></td><td colspan="2" rowspan="3">1,25</td><td colspan="3"></td><td colspan="2" rowspan="3">1,2</td><td rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td colspan="3">1,0 1,1</td><td>1,0</td><td colspan="2">1,1 1,1</td></tr>
</table>


<a id="p101353"></a>*Примечание.* При обработке внутренних канавок и канавок на торце время по карте принимать с коэффициентом К = 1,15.


<table>
<colgroup><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="7%"><col width="4%"><col width="7%"><col width="5%"><col width="8%"><col width="3%"><col width="4%"><col width="5%"><col width="4%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12">Неполное штучное время Обработка фасок</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="12">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="7">Резцы из стали Р6М5 и с пластинками Т15К6</td></tr>
<tr><td colspan="12">Единичное и мелкосерийное производство</td><td colspan="7">Карта 36</td></tr>
<tr><td rowspan="4">N позиции</td><td colspan="2" rowspan="4">Диаметр обрабатываемой поверхности D, мм, до</td><td colspan="8">Резцы из стали Р6М5</td><td colspan="8">Резцы с пластинками Т15К6</td></tr>
<tr><td colspan="5">Ширина фаски, мм, до</td><td colspan="3">Режимы резания</td><td colspan="5">Ширина фаски, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td colspan="2">3</td><td>5</td><td colspan="2">8 10</td><td rowspan="2">S , м мм/ мин.</td><td colspan="2" rowspan="2">v, N , м/ р мин. кВт, до</td><td colspan="2">3</td><td>5</td><td colspan="2">8 10</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="5">Время на поверхность, мин.</td><td colspan="5">Время на поверхность, мин.</td></tr>
<tr><td>1</td><td colspan="2">50</td><td colspan="2">0,7</td><td>0,8</td><td colspan="2">1,0 1,2</td><td rowspan="2">12,0</td><td colspan="2" rowspan="7">40 1</td><td colspan="2">0,60</td><td>0,7</td><td colspan="2">0,9 1,00</td><td>18,0</td><td rowspan="7">120</td><td rowspan="7">1</td></tr>
<tr><td>2</td><td colspan="2">100</td><td colspan="2">0,9</td><td>1,0</td><td colspan="2">1,3 1,5</td><td colspan="2">0,80</td><td>0,9</td><td colspan="2">1,1 1,25</td><td>16,0</td></tr>
<tr><td>3</td><td colspan="2">200</td><td colspan="2">1,0</td><td>1,3</td><td colspan="2">1,5 1,8</td><td>8,5</td><td colspan="2">0,90</td><td>1,0</td><td colspan="2">1,3 1,50</td><td>12,0</td></tr>
<tr><td>4</td><td colspan="2">300</td><td colspan="2">1,1</td><td>1,5</td><td colspan="2">1,9 2,3</td><td>6,0</td><td colspan="2">1,00</td><td>1,2</td><td colspan="2">1,6 1,80</td><td>8,5</td></tr>
<tr><td>5</td><td colspan="2">400</td><td colspan="2">1,2</td><td>1,7</td><td colspan="2">2,2 2,6</td><td>5,0</td><td colspan="2">1,10</td><td>1,4</td><td colspan="2">1,8 2,10</td><td>7,0</td></tr>
<tr><td>6</td><td colspan="2">500</td><td colspan="2">1,4</td><td>2,0</td><td colspan="2">2,6 3,1</td><td>4,0</td><td colspan="2">1,25</td><td>1,6</td><td colspan="2">2,1 2,40</td><td>5,5</td></tr>
<tr><td>7</td><td colspan="2">600</td><td colspan="2">1,7</td><td>2,4</td><td colspan="2">3,2 3,9</td><td>3,0</td><td colspan="2">1,40</td><td>1,9</td><td colspan="2">2,4 3,00</td><td>4,2</td></tr>
<tr><td colspan="3">Индекс</td><td colspan="2">а</td><td>б</td><td colspan="2">в г</td><td colspan="3"></td><td colspan="2">д</td><td>е</td><td colspan="2">ж з</td><td colspan="3"></td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="9">Группы стали и предела прочности</td><td colspan="2" rowspan="9">Инструмент</td><td colspan="3" rowspan="5">из быстрорежущей стали Р6М5</td><td colspan="3">Группа стали</td><td colspan="5">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="4">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="5">до 0,59 - свыше 0,59 0,74 0,74</td><td colspan="4">до 0,59 - свыше 0,59 0,74 0,74</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="5"></td><td colspan="4" rowspan="3">1,1 1,2 1,35</td></tr>
<tr><td>0,8</td><td colspan="4">1,0 1,25</td></tr>
<tr><td colspan="5"></td></tr>
<tr><td colspan="3" rowspan="4">с пластинками из твердого сплава Т15К6</td><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="5">до 0,59 - свыше 0,59 0,74 0,74</td><td colspan="4" rowspan="4"></td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="5"></td></tr>
<tr><td>0,8</td><td colspan="4">1,0 1,25</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="7%"><col width="4%"><col width="7%"><col width="5%"><col width="8%"><col width="3%"><col width="4%"><col width="5%"><col width="4%"><col width="8%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="12">Неполное штучное время Обработка радиусов</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="12">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="7">Резцы из стали Р6М5 и с пластинками Т15К6</td></tr>
<tr><td colspan="12">Единичное и мелкосерийное производство</td><td colspan="7">Карта 37</td></tr>
<tr><td rowspan="4">N позиции</td><td colspan="2" rowspan="4">Диаметр обрабатываемой поверхности D, мм, до</td><td colspan="8">Резцы из стали Р6М5</td><td colspan="8">Резцы с пластинками Т15К6</td></tr>
<tr><td colspan="5">Размер радиуса, мм, до</td><td colspan="3">Режимы резания</td><td colspan="5">Размер радиуса, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td colspan="2">3</td><td>5</td><td colspan="2">8 10</td><td rowspan="2">S , м мм/ мин.</td><td colspan="2" rowspan="2">v, N , м/ р мин. кВт, до</td><td colspan="2">3</td><td>5</td><td colspan="2">8 10</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="5">Время на поверхность, мин.</td><td colspan="5">Время на поверхность, мин.</td></tr>
<tr><td>1</td><td colspan="2">50</td><td colspan="2">0,7</td><td>0,8</td><td colspan="2">1,0 1,2</td><td>15,0</td><td colspan="2" rowspan="7">40 1</td><td colspan="2">0,60</td><td>0,7</td><td colspan="2">0,9 1,00</td><td>18</td><td rowspan="7">120</td><td rowspan="7">1</td></tr>
<tr><td>2</td><td colspan="2">100</td><td colspan="2">0,9</td><td>1,0</td><td colspan="2">1,3 1,5</td><td>12,0</td><td colspan="2">0,80</td><td>0,9</td><td colspan="2">1,1 1,25</td><td>16</td></tr>
<tr><td>3</td><td colspan="2">200</td><td colspan="2">2,2</td><td>2,5</td><td colspan="2">3,0 3,4</td><td>6,0</td><td colspan="2">2,0</td><td>2,3</td><td colspan="2">2,6 2,90</td><td>8</td></tr>
<tr><td>4</td><td colspan="2">300</td><td colspan="2">2,5</td><td>3,0</td><td colspan="2">3,9 4,4</td><td>4,0</td><td colspan="2">2,2</td><td>2,5</td><td colspan="2">3,0 3,40</td><td>6</td></tr>
<tr><td>5</td><td colspan="2">400</td><td colspan="2">2,6</td><td>3,3</td><td colspan="2">4,2 4,8</td><td>3,5</td><td colspan="2">2,3</td><td>2,7</td><td colspan="2">3,4 3,90</td><td>5</td></tr>
<tr><td>6</td><td colspan="2">500</td><td colspan="2">3,0</td><td>3,7</td><td colspan="2">4,9 5,5</td><td>2,8</td><td colspan="2">2,5</td><td>3,0</td><td colspan="2">3,9 4,40</td><td>4</td></tr>
<tr><td>7</td><td colspan="2">600</td><td colspan="2">3,6</td><td>4,7</td><td colspan="2">6,5 7,5</td><td>2,0</td><td colspan="2">2,9</td><td>3,6</td><td colspan="2">4,7 5,50</td><td>3</td></tr>
<tr><td colspan="3">Индекс</td><td colspan="2">а</td><td>б</td><td colspan="2">в г</td><td colspan="3"></td><td colspan="2">д</td><td>е</td><td colspan="2">ж з</td><td colspan="3"></td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="9">Группы стали и предела прочности</td><td colspan="2" rowspan="9">Инструмент</td><td colspan="3" rowspan="5">из быстрорежущей стали Р6М5</td><td colspan="3">Группа стали</td><td colspan="5">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="4">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="5">до 0,59 - свыше 0,59 0,74 0,74</td><td colspan="4">до 0,59 - свыше 0,59 0,74 0,74</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="5"></td><td colspan="4" rowspan="3">1,1 1,2 1,35</td></tr>
<tr><td>0,8</td><td colspan="4">1,0 1,25</td></tr>
<tr><td colspan="5"></td></tr>
<tr><td colspan="3" rowspan="4">с пластинками из твердого сплава Т15К6</td><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="5">до 0,59 - свыше 0,59 0,74 0,74</td><td colspan="4" rowspan="4"></td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="5"></td></tr>
<tr><td>0,8</td><td colspan="4">1,0 1,25</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="6%"><col width="8%"><col width="8%"><col width="8%"><col width="3%"><col width="5%"><col width="3%"><col width="5%"><col width="3%"><col width="5%"><col width="8%"><col width="8%"><col width="11%"><col width="3%"><col width="5%"><col width="8%"></colgroup>
<tr><td colspan="17">Неполное штучное время Горизонтально-расточные станки Цекование торцов и отверстий</td></tr>
<tr><td colspan="17">Сталь конструкционная углеро- Цековки и пластины из стали дистая, сигма = 0,59 - 0,74 ГПа Р6М5 в</td></tr>
<tr><td colspan="17">Единичное и мелкосерийное Карта 38 производство</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Диаметр обрабатываемой поверхности D, мм, до</td><td colspan="10">Глубина цекования l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>2,5</td><td>3,5</td><td colspan="2">5</td><td colspan="2">7</td><td colspan="2">10</td><td>14</td><td>20</td><td rowspan="2">S , о мм/об.</td><td colspan="2" rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="10">Время на поверхность, мин.</td></tr>
<tr><td colspan="17">Подрезание торцов цековками</td></tr>
<tr><td>1</td><td colspan="2">30</td><td>0,55</td><td>0,60</td><td colspan="2">0,75</td><td colspan="2">0,75</td><td colspan="2">0,85</td><td>1,00</td><td>1,30</td><td rowspan="4">0,20</td><td colspan="2">7,2</td><td rowspan="4">1,5</td></tr>
<tr><td>2</td><td colspan="2">40</td><td>0,60</td><td>0,70</td><td colspan="2">0,85</td><td colspan="2">0,85</td><td colspan="2">0,95</td><td>1,20</td><td>1,50</td><td colspan="2">7,5</td></tr>
<tr><td>3</td><td colspan="2">55</td><td>0,75</td><td>0,85</td><td colspan="2">1,10</td><td colspan="2">1,05</td><td colspan="2">1,30</td><td>1,60</td><td>2,10</td><td colspan="2">7,0</td></tr>
<tr><td>4</td><td colspan="2">72</td><td>0,85</td><td>1,00</td><td colspan="2">1,25</td><td colspan="2">1,30</td><td colspan="2">1,50</td><td>1,90</td><td>2,50</td><td colspan="2">6,7</td></tr>
<tr><td colspan="17">Цекование отверстий под головку болта</td></tr>
<tr><td>5</td><td colspan="2">30</td><td>0,80</td><td>0,90</td><td colspan="2">1,00</td><td colspan="2">1,10</td><td colspan="2">1,30</td><td>1,60</td><td>2,00</td><td rowspan="4">0,18</td><td colspan="2">7,2</td><td rowspan="4">1,5</td></tr>
<tr><td>6</td><td colspan="2">40</td><td>0,85</td><td>0,95</td><td colspan="2">1,10</td><td colspan="2">1,30</td><td colspan="2">1,55</td><td>1,90</td><td>2,40</td><td colspan="2">7,5</td></tr>
<tr><td>7</td><td colspan="2">55</td><td>1,00</td><td>1,15</td><td colspan="2">1,40</td><td colspan="2">1,60</td><td colspan="2">2,00</td><td>2,50</td><td>3,30</td><td colspan="2">7,0</td></tr>
<tr><td>8</td><td colspan="2">72</td><td>1,15</td><td>1,35</td><td colspan="2">1,65</td><td colspan="2">1,95</td><td colspan="2">2,50</td><td>3,20</td><td>4,20</td><td colspan="2">6,7</td></tr>
<tr><td colspan="17">Подрезание торцов пластинами</td></tr>
<tr><td>9</td><td colspan="2">30</td><td>0,65</td><td>0,75</td><td colspan="2">0,85</td><td colspan="2">1,00</td><td colspan="2">1,15</td><td>1,45</td><td>1,80</td><td rowspan="4">0,15</td><td colspan="2">9,0</td><td rowspan="4">1,5</td></tr>
<tr><td>10</td><td colspan="2">40</td><td>0,75</td><td>0,85</td><td colspan="2">1,00</td><td colspan="2">1,15</td><td colspan="2">1,35</td><td>1,70</td><td>2,20</td><td colspan="2">9,5</td></tr>
<tr><td>11</td><td colspan="2">55</td><td>0,80</td><td>0,95</td><td colspan="2">1,10</td><td colspan="2">1,30</td><td colspan="2">1,60</td><td>2,00</td><td>2,60</td><td colspan="2">10,5</td></tr>
<tr><td>12</td><td colspan="2">72</td><td>1,00</td><td>1,15</td><td colspan="2">1,45</td><td colspan="2">1,70</td><td colspan="2">2,15</td><td>2,80</td><td>3,70</td><td colspan="2">9,0</td></tr>
<tr><td colspan="17">Цекование отверстий под головку болта пластинами</td></tr>
<tr><td>13</td><td colspan="2">30</td><td>0,85</td><td>0,95</td><td colspan="2">1,05</td><td colspan="2">1,20</td><td colspan="2">1,45</td><td>1,80</td><td>2,20</td><td rowspan="4">0,12</td><td colspan="2">9,0</td><td rowspan="4">1,5</td></tr>
<tr><td>14</td><td colspan="2">40</td><td>0,90</td><td>1,05</td><td colspan="2">1,20</td><td colspan="2">1,40</td><td colspan="2">1,70</td><td>2,10</td><td>2,75</td><td colspan="2">9,5</td></tr>
<tr><td>15</td><td colspan="2">55</td><td>1,10</td><td>1,25</td><td colspan="2">1,55</td><td colspan="2">1,80</td><td colspan="2">2,30</td><td>2,90</td><td>3,80</td><td colspan="2">8,5</td></tr>
<tr><td>16</td><td colspan="2">72</td><td>1,25</td><td>1,45</td><td colspan="2">1,80</td><td colspan="2">2,15</td><td colspan="2">2,70</td><td>3,50</td><td>4,60</td><td colspan="2">9,0</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td colspan="2">г</td><td colspan="2">д</td><td>е</td><td>ж</td><td colspan="4"></td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="5">Группы стали и предела прочности</td><td colspan="4">Группа стали</td><td colspan="6">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="5">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="4">Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="4">0,59 - свыше 0,74 0,74</td><td colspan="3">до 0,59 - 0,59 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td colspan="4" rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="4"></td><td colspan="3" rowspan="3">1,1 1,2</td><td colspan="2" rowspan="3">1,35</td></tr>
<tr><td colspan="2">1,0</td><td colspan="2">1,25</td></tr>
</table>


<a id="p101413"></a>*Примечание.* При обработке обратными цековками и пластинами время по карте принимать с коэффициентом К = 1,15.


<table>
<colgroup><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="3%"><col width="4%"><col width="7%"><col width="3%"><col width="4%"><col width="4%"><col width="3%"><col width="5%"><col width="3%"><col width="3%"><col width="5%"><col width="3%"><col width="5%"><col width="8%"></colgroup>
<tr><td colspan="21">Неполное штучное время Горизонтально-расточные станки Нарезание внутренней метрической резьбы, 1Т9 квалитет Резцы из стали Р6М5 Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Карта 39 в Единичное и мелкосерийное производство</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Диаметр нарезаемой резьбы D, мм</td><td colspan="9">Длина нарезаемой резьбы l, мм, до</td><td colspan="9">Режимы резания</td></tr>
<tr><td>25</td><td>50</td><td>75</td><td>100</td><td colspan="2">125</td><td>150</td><td colspan="2">200</td><td colspan="2" rowspan="2">Р, мм</td><td colspan="4">Число проходов i</td><td colspan="3">v, м/мин.</td></tr>
<tr><td colspan="9">Время на поверхность, мин.</td><td colspan="2">черновые</td><td colspan="2">чистовые</td><td colspan="2">черновые</td><td>чистовые</td></tr>
<tr><td>1</td><td colspan="2" rowspan="4">36 - 42</td><td>4,3</td><td>6,5</td><td>9,0</td><td>12,0</td><td colspan="2">15,0</td><td>18,0</td><td colspan="2">-</td><td colspan="2">1</td><td colspan="2" rowspan="3">7</td><td colspan="2" rowspan="3">2</td><td colspan="2" rowspan="3">14</td><td rowspan="28">5</td></tr>
<tr><td>2</td><td>4,1</td><td>5,0</td><td>6,5</td><td>8,0</td><td colspan="2">9,5</td><td>11,0</td><td colspan="2">-</td><td colspan="2">2</td></tr>
<tr><td>3</td><td>3,8</td><td>4,5</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td>8,5</td><td colspan="2">-</td><td colspan="2">3</td></tr>
<tr><td>4</td><td>4,2</td><td>5,0</td><td>6,0</td><td>7,0</td><td colspan="2">8,0</td><td>9,0</td><td colspan="2">-</td><td colspan="2">4</td><td colspan="2">9</td><td colspan="2">2</td><td colspan="2">11</td></tr>
<tr><td>5</td><td colspan="2" rowspan="4">48</td><td>5,0</td><td>7,5</td><td>11,0</td><td>14,5</td><td colspan="2">18,0</td><td>22,0</td><td colspan="2">27,0</td><td colspan="2">1</td><td colspan="2" rowspan="3">7</td><td colspan="2" rowspan="3">2</td><td colspan="2" rowspan="3">14</td></tr>
<tr><td>6</td><td>4,5</td><td>6,0</td><td>7,5</td><td>9,5</td><td colspan="2">11,5</td><td>13,0</td><td colspan="2">15,5</td><td colspan="2">2</td></tr>
<tr><td>7</td><td>4,1</td><td>5,0</td><td>6,0</td><td>7,5</td><td colspan="2">8,5</td><td>10,0</td><td colspan="2">11,5</td><td colspan="2">3</td></tr>
<tr><td>8</td><td>4,7</td><td>5,5</td><td>6,5</td><td>8,0</td><td colspan="2">9,5</td><td>11,0</td><td colspan="2">12,5</td><td colspan="2">4</td><td colspan="2">9</td><td colspan="2">2</td><td colspan="2">11</td></tr>
<tr><td>9</td><td colspan="2" rowspan="4">64</td><td>6,5</td><td>10,5</td><td>15,0</td><td>20,0</td><td colspan="2">25,0</td><td>29,0</td><td colspan="2">37,0</td><td colspan="2">1</td><td colspan="2" rowspan="3">7</td><td colspan="2" rowspan="3">2</td><td colspan="2" rowspan="3">14</td></tr>
<tr><td>10</td><td>5,5</td><td>7,5</td><td>9,5</td><td>12,0</td><td colspan="2">15,0</td><td>17,0</td><td colspan="2">21,0</td><td colspan="2">2</td></tr>
<tr><td>11</td><td>5,0</td><td>6,0</td><td>7,5</td><td>9,5</td><td colspan="2">11,5</td><td>13,0</td><td colspan="2">15,5</td><td colspan="2">3</td></tr>
<tr><td>12</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,0</td><td colspan="2">12,5</td><td>14,0</td><td colspan="2">16,0</td><td colspan="2">4</td><td colspan="2">9</td><td colspan="2">2</td><td colspan="2">11</td></tr>
<tr><td>13</td><td colspan="2" rowspan="4">72</td><td>8,0</td><td>12,0</td><td>18,0</td><td>24,0</td><td colspan="2">30,0</td><td>36,0</td><td colspan="2">45,0</td><td colspan="2">1</td><td colspan="2" rowspan="3">7</td><td colspan="2" rowspan="3">2</td><td colspan="2" rowspan="3">14</td></tr>
<tr><td>14</td><td>6,0</td><td>8,5</td><td>11,5</td><td>14,5</td><td colspan="2">18,0</td><td>21,0</td><td colspan="2">25,0</td><td colspan="2">2</td></tr>
<tr><td>15</td><td>5,5</td><td>7,0</td><td>9,0</td><td>11,0</td><td colspan="2">13,5</td><td>15,5</td><td colspan="2">18,5</td><td colspan="2">3</td></tr>
<tr><td>16</td><td>6,5</td><td>8,0</td><td>10,0</td><td>12,0</td><td colspan="2">14,5</td><td>14,5</td><td colspan="2">19,5</td><td colspan="2">4</td><td colspan="2">9</td><td colspan="2">2</td><td colspan="2">11</td></tr>
<tr><td>17</td><td colspan="2" rowspan="3">90</td><td>7,0</td><td>10,0</td><td>13,5</td><td>17,5</td><td colspan="2">21,5</td><td>25,0</td><td colspan="2">31,0</td><td colspan="2">2</td><td colspan="2" rowspan="2">7</td><td colspan="2" rowspan="2">2</td><td colspan="2" rowspan="2">14</td></tr>
<tr><td>18</td><td>6,0</td><td>8,0</td><td>10,5</td><td>13,0</td><td colspan="2">16,0</td><td>18,5</td><td colspan="2">22,0</td><td colspan="2">3</td></tr>
<tr><td>19</td><td>7,5</td><td>9,0</td><td>11,5</td><td>14,0</td><td colspan="2">17,0</td><td>19,5</td><td colspan="2">23,0</td><td colspan="2">4</td><td colspan="2">9</td><td colspan="2">2</td><td colspan="2">11</td></tr>
<tr><td>20</td><td colspan="2" rowspan="3">100 - 125</td><td>8,5</td><td>12,0</td><td>16,5</td><td>21,0</td><td colspan="2">26,0</td><td>30,0</td><td colspan="2">37,0</td><td colspan="2">2</td><td colspan="2" rowspan="2">7</td><td colspan="2" rowspan="2">2</td><td colspan="2" rowspan="2">14</td></tr>
<tr><td>21</td><td>7,5</td><td>10,0</td><td>13,0</td><td>16,0</td><td colspan="2">19,0</td><td>22,0</td><td colspan="2">26,0</td><td colspan="2">3</td></tr>
<tr><td>22</td><td>8,5</td><td>11,0</td><td>14,0</td><td>17,0</td><td colspan="2">20,5</td><td>23,0</td><td colspan="2">28,0</td><td colspan="2">4</td><td colspan="2">9</td><td colspan="2">2</td><td colspan="2">11</td></tr>
<tr><td>23</td><td colspan="2" rowspan="3">140 - 160</td><td>10,5</td><td>14,5</td><td>20,0</td><td>26,5</td><td colspan="2">33,0</td><td>39,0</td><td colspan="2">48,0</td><td colspan="2">2</td><td colspan="2" rowspan="2">7</td><td colspan="2" rowspan="2">2</td><td colspan="2" rowspan="2">14</td></tr>
<tr><td>24</td><td>9,0</td><td>12,0</td><td>16,0</td><td>20,0</td><td colspan="2">24,0</td><td>28,0</td><td colspan="2">34,0</td><td colspan="2">3</td></tr>
<tr><td>25</td><td>10,0</td><td>13,0</td><td>17,0</td><td>21,0</td><td colspan="2">25,0</td><td>29,0</td><td colspan="2">35,0</td><td colspan="2">4</td><td colspan="2">9</td><td colspan="2">2</td><td colspan="2">11</td></tr>
<tr><td>26</td><td colspan="2" rowspan="3">180 - 200</td><td>12,0</td><td>17,0</td><td>25,0</td><td>32,0</td><td colspan="2">40,0</td><td>47,0</td><td colspan="2">39,0</td><td colspan="2">2</td><td colspan="2" rowspan="2">7</td><td colspan="2" rowspan="2">2</td><td colspan="2" rowspan="2">14</td></tr>
<tr><td>27</td><td>10,5</td><td>14,0</td><td>19,0</td><td>24,0</td><td colspan="2">29,0</td><td>34,0</td><td colspan="2">42,0</td><td colspan="2">3</td></tr>
<tr><td>28</td><td>12,0</td><td>15,5</td><td>20,5</td><td>25,0</td><td colspan="2">31,0</td><td>36,0</td><td colspan="2">43,0</td><td colspan="2">4</td><td colspan="2">9</td><td colspan="2">2</td><td colspan="2">11</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td colspan="2">ж</td><td colspan="9"></td></tr>
<tr><td colspan="21">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="6">Группы стали, предела прочности и продолжительности обработки</td><td colspan="9">Группа Углеродистые, хромистые, стали никелевые, хромоникелевые</td><td colspan="10">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="4">Предел до 0,59 прочности сигма , в ГПа</td><td colspan="2">0,59 - 0,74</td><td colspan="3">свыше 0,74</td><td colspan="4">до 0,59</td><td colspan="4">0,59 - 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td colspan="3">Продолжи- до тельность 10 обработки, мин.</td><td>свыше 10</td><td colspan="2">-</td><td colspan="3">до свыше 10 10</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td><td>до 10</td><td>свыше 10</td></tr>
<tr><td colspan="3" rowspan="3">Коэффици- 0,9 ент</td><td rowspan="3">0,8</td><td colspan="2"></td><td colspan="3" rowspan="3">1,1 1,25</td><td colspan="2"></td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td></td><td colspan="2">1,0</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="8%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="26">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="26">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Борштанги консольные Единичное и мелкосерийное производство Резцы из стали Р6М5</td></tr>
<tr><td colspan="23">Карта 40</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="20">10</td><td>30</td><td>2</td><td>1,15</td><td>1,30</td><td>1,45</td><td>1,55</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,35</td><td colspan="2">600</td><td>56,5</td><td>&lt; 1</td></tr>
<tr><td>2</td><td rowspan="2">48</td><td>3</td><td>1,20</td><td>1,35</td><td>1,45</td><td>1,60</td><td>2,00</td><td>2,10</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,50</td><td colspan="2" rowspan="2">380</td><td rowspan="2">57,0</td><td>&lt; 1</td></tr>
<tr><td>3</td><td>5</td><td>1,25</td><td>1,45</td><td>1,65</td><td>1,85</td><td>2,30</td><td>2,50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,35</td><td>1,1</td></tr>
<tr><td>4</td><td rowspan="2">60</td><td>3</td><td>1,20</td><td>1,35</td><td>1,50</td><td>1,70</td><td>2,05</td><td>2,25</td><td>2,40</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,70</td><td colspan="2" rowspan="2">240</td><td rowspan="2">46,0</td><td>&lt; 1</td></tr>
<tr><td>5</td><td>5</td><td>1,25</td><td>1,45</td><td>1,65</td><td>1,85</td><td>2,25</td><td>2,50</td><td>2,70</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,56</td><td>1,3</td></tr>
<tr><td>6</td><td rowspan="3">75</td><td>3</td><td>1,20</td><td>1,45</td><td>1,65</td><td>1,85</td><td>2,25</td><td>2,45</td><td>7,70</td><td>2,90</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,70</td><td colspan="2" rowspan="3">190</td><td rowspan="3">45,0</td><td>&lt; 1</td></tr>
<tr><td>7</td><td>5</td><td>1,30</td><td>1,55</td><td>1,80</td><td>2,05</td><td>2,55</td><td>2,80</td><td>3,05</td><td>3,30</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,56</td><td>1,1</td></tr>
<tr><td>8</td><td>8</td><td>1,45</td><td>1,85</td><td>2,25</td><td>2,60</td><td>3,30</td><td>3,70</td><td>4,10</td><td>4,50</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,35</td><td>1,6</td></tr>
<tr><td>9</td><td rowspan="3">96</td><td>3</td><td>1,75</td><td>1,50</td><td>1,80</td><td>2,05</td><td>2,50</td><td>2,80</td><td>3,05</td><td>3,30</td><td>3,7</td><td>4,20</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,70</td><td colspan="2" rowspan="3">150</td><td rowspan="3">45,0</td><td>&lt; 1</td></tr>
<tr><td>10</td><td>5</td><td>1,30</td><td>1,65</td><td>1,95</td><td>2,30</td><td>2,85</td><td>3,15</td><td>3,50</td><td>3,80</td><td>4,3</td><td>4,95</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,56</td><td>1,3</td></tr>
<tr><td>11</td><td>8</td><td>1,50</td><td>2,05</td><td>2,55</td><td>3,10</td><td>3,85</td><td>4,35</td><td>4,90</td><td>5,50</td><td>6,0</td><td>7,00</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,35</td><td>1,3</td></tr>
<tr><td>12</td><td rowspan="4">120</td><td>3</td><td>1,30</td><td>1,60</td><td>1,95</td><td>2,25</td><td>2,80</td><td>3,15</td><td>3,45</td><td>3,80</td><td>4,2</td><td>4,95</td><td>5,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,70</td><td colspan="2" rowspan="4">120</td><td rowspan="4">45,0</td><td>&lt; 1</td></tr>
<tr><td>13</td><td>5</td><td>1,40</td><td>1,80</td><td>2,20</td><td>2,60</td><td>3,25</td><td>3,65</td><td>4,05</td><td>4,45</td><td>5,0</td><td>6,00</td><td>7,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,56</td><td>1,1</td></tr>
<tr><td>14</td><td>8</td><td>1,50</td><td>2,00</td><td>2,50</td><td>3,00</td><td>3,75</td><td>4,25</td><td>4,75</td><td>5,00</td><td>6,0</td><td>7,00</td><td>8,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,45</td><td>1,6</td></tr>
<tr><td>15</td><td>12</td><td>1,70</td><td>2,30</td><td>3,00</td><td>3,60</td><td>4,50</td><td>5,00</td><td>6,00</td><td>6,50</td><td>7,5</td><td>8,50</td><td>10,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,35</td><td>2,2</td></tr>
<tr><td>16</td><td rowspan="4">150</td><td>3</td><td>1,35</td><td>1,75</td><td>2,15</td><td>2,55</td><td>3,20</td><td>3,60</td><td>4,00</td><td>4,45</td><td>5,0</td><td>6,00</td><td>7,0</td><td>7,5</td><td>8,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,70</td><td colspan="2" rowspan="4">96</td><td rowspan="4">45,0</td><td>&lt; 1</td></tr>
<tr><td>17</td><td>5</td><td>1,45</td><td>1,95</td><td>2,45</td><td>2,95</td><td>3,70</td><td>4,20</td><td>4,70</td><td>5,00</td><td>6,0</td><td>7,00</td><td>8,0</td><td>9,0</td><td>10,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,56</td><td>1,3</td></tr>
<tr><td>18</td><td>8</td><td>1,60</td><td>2,25</td><td>2,85</td><td>3,50</td><td>4,35</td><td>5,00</td><td>5,50</td><td>6,00</td><td>7,0</td><td>8,50</td><td>10,0</td><td>11,0</td><td>12,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,45</td><td>1,6</td></tr>
<tr><td>19</td><td>12</td><td>1,80</td><td>2,65</td><td>3,45</td><td>4,30</td><td>5,50</td><td>6,00</td><td>7,00</td><td>8,00</td><td>9,0</td><td>11,0</td><td>12,5</td><td>14,0</td><td>16,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,35</td><td>2,2</td></tr>
<tr><td>20</td><td></td><td>3</td><td>1,40</td><td>1,95</td><td>2,45</td><td>3,00</td><td>3,75</td><td>4,25</td><td>4,80</td><td>5,50</td><td>6,0</td><td>7,00</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,5</td><td>13</td><td>-</td><td>-</td><td>0,70</td><td colspan="2"></td><td></td><td>&lt; 1</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="8%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="26">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="26">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Борштанги консольные Единичное и мелкосерийное производство Резцы из стали Р6М5</td></tr>
<tr><td colspan="23">Карта 40</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>21</td><td rowspan="15">10</td><td rowspan="3">190</td><td>5</td><td>1,55</td><td>2,20</td><td>2,85</td><td>3,50</td><td>4,40</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>12,5</td><td>14,0</td><td>16,0</td><td>-</td><td>-</td><td>0,56</td><td colspan="2" rowspan="3">75</td><td rowspan="3">45</td><td>1,3</td></tr>
<tr><td>22</td><td>8</td><td>1,70</td><td>2,55</td><td>3,35</td><td>4,15</td><td>5,00</td><td>6,0</td><td>7,0</td><td>7,5</td><td>9,0</td><td>10,5</td><td>12,0</td><td>13,5</td><td>15,5</td><td>17,0</td><td>19,5</td><td>-</td><td>-</td><td>0,45</td><td>1,6</td></tr>
<tr><td>23</td><td>12</td><td>2,00</td><td>3,05</td><td>4,10</td><td>5,00</td><td>6,50</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,0</td><td>13,0</td><td>15,5</td><td>17,5</td><td>19,5</td><td>22,0</td><td>25,0</td><td>-</td><td>-</td><td>0,35</td><td>2,2</td></tr>
<tr><td>24</td><td rowspan="4">240</td><td>3</td><td>1,50</td><td>2,15</td><td>2,80</td><td>3,45</td><td>4,35</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,5</td><td>14,0</td><td>16,0</td><td>19,0</td><td>2,60</td><td>0,70</td><td colspan="2" rowspan="4">60</td><td rowspan="4">45</td><td>&lt; 1</td></tr>
<tr><td>25</td><td>5</td><td>1,65</td><td>2,45</td><td>3,25</td><td>4,05</td><td>5,00</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,5</td><td>12,0</td><td>13,5</td><td>15,0</td><td>17,0</td><td>19,0</td><td>23,5</td><td>3,25</td><td>0,56</td><td>1,3</td></tr>
<tr><td>26</td><td>8</td><td>1,90</td><td>2,90</td><td>3,90</td><td>4,95</td><td>6,00</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>13,0</td><td>15,0</td><td>17,0</td><td>19,0</td><td>21,0</td><td>24,0</td><td>29,0</td><td>4,05</td><td>0,45</td><td>1,6</td></tr>
<tr><td>27</td><td>12</td><td>2,20</td><td>3,50</td><td>4,80</td><td>6,00</td><td>7,50</td><td>9,0</td><td>10,0</td><td>11,5</td><td>13,5</td><td>16,0</td><td>19,0</td><td>21,5</td><td>24,0</td><td>26,5</td><td>30,5</td><td>37,0</td><td>5,00</td><td>0,35</td><td>2,2</td></tr>
<tr><td>28</td><td rowspan="4">300</td><td>3</td><td>1,60</td><td>2,40</td><td>3,20</td><td>4,00</td><td>5,00</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>12,0</td><td>13,5</td><td>15,0</td><td>17,0</td><td>19,5</td><td>23,5</td><td>3,25</td><td>0,70</td><td colspan="2" rowspan="4">48</td><td rowspan="4">45</td><td>&lt; 1</td></tr>
<tr><td>29</td><td>5</td><td>1,80</td><td>2,80</td><td>3,85</td><td>4,85</td><td>6,00</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,5</td><td>15,0</td><td>17,0</td><td>19,0</td><td>21,0</td><td>24,0</td><td>29,0</td><td>4,05</td><td>0,56</td><td>1,3</td></tr>
<tr><td>30</td><td>8</td><td>2,05</td><td>3,30</td><td>4,55</td><td>6,00</td><td>7,00</td><td>8,5</td><td>10,0</td><td>11,0</td><td>13,0</td><td>15,5</td><td>18,0</td><td>20,5</td><td>23,0</td><td>25,5</td><td>29,0</td><td>35,5</td><td>5,00</td><td>0,45</td><td>1,6</td></tr>
<tr><td>31</td><td>12</td><td>2,50</td><td>4,00</td><td>5,50</td><td>7,50</td><td>9,00</td><td>11,0</td><td>12,5</td><td>14,0</td><td>16,5</td><td>19,5</td><td>23,0</td><td>26,0</td><td>29,5</td><td>32,5</td><td>37,5</td><td>45,5</td><td>6,50</td><td>0,35</td><td>2,2</td></tr>
<tr><td>32</td><td rowspan="4">380</td><td>3</td><td>1,70</td><td>2,75</td><td>3,75</td><td>4,75</td><td>6,00</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,5</td><td>14,5</td><td>17,0</td><td>19,0</td><td>21,0</td><td>24,0</td><td>29,0</td><td>4,10</td><td>0,70</td><td colspan="2" rowspan="4">38</td><td rowspan="4">45</td><td>&lt; 1</td></tr>
<tr><td>33</td><td>5</td><td>2,00</td><td>3,30</td><td>4,60</td><td>6,00</td><td>7,50</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td>16,0</td><td>18,5</td><td>21,0</td><td>24,0</td><td>26,5</td><td>30,5</td><td>34,0</td><td>5,00</td><td>0,56</td><td>1,3</td></tr>
<tr><td>34</td><td>8</td><td>2,35</td><td>4,00</td><td>5,50</td><td>7,00</td><td>9,00</td><td>10,5</td><td>12,0</td><td>14,0</td><td>16,0</td><td>19,5</td><td>23,0</td><td>26,0</td><td>29,0</td><td>32,5</td><td>37,5</td><td>45,5</td><td>6,50</td><td>0,45</td><td>1,6</td></tr>
<tr><td>35</td><td>12</td><td>2,90</td><td>5,00</td><td>7,00</td><td>9,00</td><td>11,5</td><td>13,5</td><td>16,0</td><td>18,0</td><td>21,0</td><td>25,0</td><td>29,5</td><td>34,0</td><td>38,0</td><td>42,0</td><td>48,5</td><td>59,0</td><td>8,00</td><td>0,35</td><td>2,2</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="19%"><col width="32%"><col width="5%"><col width="7%"><col width="8%"><col width="4%"><col width="5%"><col width="7%"><col width="2%"><col width="4%"><col width="8%"></colgroup>
<tr><td colspan="5">Неполное штучное время Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="5" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Единичное и мелкосерийное производство</td><td colspan="6">Борштанги консольные Резцы из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 40</td><td colspan="2">Лист 3</td></tr>
<tr><td colspan="11">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td>Группы медных сплавов, твердости</td><td>Группа сплавов</td><td colspan="4">Гомогенные</td><td colspan="5">Гетерогенные</td></tr>
<tr><td rowspan="5">и продолжительности обработки</td><td>Твердость НВ, ГПа</td><td colspan="4">0,59 - 0,88</td><td colspan="2">0,98 - 1,37</td><td colspan="3">1,47 - 2,45</td></tr>
<tr><td>Продолжительность обработки, мин.</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td><td colspan="2">-</td><td colspan="2">до 10</td><td>свыше 10</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,7</td><td colspan="2" rowspan="3">0,55</td><td colspan="2"></td><td colspan="2" rowspan="3">1,1</td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td>Группы алюминиевых сплавов, твердости</td><td>Группа сплавов</td><td colspan="4">Силумин и литейные сплавы</td><td colspan="5">Дюралюминий</td></tr>
<tr><td rowspan="3">и продолжительности обработки</td><td>Твердость НВ, ГПа</td><td colspan="4">до 0,64</td><td colspan="5">до 0,98</td></tr>
<tr><td>Продолжительность обработки, мин.</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td><td colspan="2">до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td>Коэффициент</td><td colspan="2">0,75</td><td colspan="2">0,7</td><td colspan="2">0,75</td><td colspan="3">0,7</td></tr>
<tr><td rowspan="4">Состояния обрабатываемой поверхности</td><td>Состояние обрабатываемой поверхности</td><td colspan="4">без корки</td><td colspan="5">по корке</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="5" rowspan="3">1,2</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="4%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="26">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="26">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Борштанги двухопорные Единичное и мелкосерийное производство Резцы из стали Р6М5</td></tr>
<tr><td colspan="23">Карта 41</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="20">10</td><td rowspan="4">120</td><td>3</td><td>2,40</td><td>2,75</td><td>3,05</td><td>3,35</td><td>4,10</td><td>4,45</td><td>4,75</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,0</td><td>9,0</td><td>9,5</td><td>11,0</td><td>12,5</td><td>1,25</td><td>0,90</td><td colspan="2" rowspan="4">96</td><td rowspan="4">36</td><td>0,9</td></tr>
<tr><td>2</td><td>5</td><td>2,50</td><td>2,90</td><td>3,30</td><td>3,75</td><td>4,55</td><td>5,00</td><td>5,50</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,0</td><td>13,0</td><td>15,0</td><td>1,65</td><td>0,70</td><td>1,3</td></tr>
<tr><td>3</td><td>8</td><td>2,60</td><td>3,10</td><td>3,60</td><td>4,15</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,0</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,0</td><td>15,0</td><td>17,5</td><td>2,05</td><td>0,56</td><td>1,8</td></tr>
<tr><td>4</td><td>12</td><td>2,75</td><td>3,40</td><td>4,05</td><td>4,65</td><td>6,00</td><td>6,50</td><td>7,00</td><td>8,0</td><td>9,0</td><td>10,0</td><td>12,0</td><td>13,0</td><td>14,5</td><td>15,5</td><td>18,0</td><td>21,0</td><td>2,50</td><td>0,45</td><td>2,4</td></tr>
<tr><td>5</td><td rowspan="4">150</td><td>3</td><td>2,45</td><td>2,90</td><td>3,30</td><td>3,70</td><td>4,55</td><td>4,95</td><td>5,50</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td>11,0</td><td>13,0</td><td>15,0</td><td>1,60</td><td>0,90</td><td colspan="2" rowspan="4">75</td><td rowspan="4">35</td><td>0,9</td></tr>
<tr><td>6</td><td>5</td><td>2,60</td><td>3,10</td><td>3,65</td><td>4,15</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,0</td><td>7,5</td><td>9,0</td><td>10,5</td><td>11,5</td><td>12,5</td><td>13,5</td><td>15,5</td><td>18,0</td><td>2,10</td><td>0,70</td><td>1,3</td></tr>
<tr><td>7</td><td>8</td><td>2,70</td><td>3,40</td><td>4,05</td><td>4,70</td><td>6,00</td><td>6,50</td><td>7,50</td><td>8,0</td><td>9,0</td><td>10,0</td><td>12,0</td><td>13,5</td><td>14,5</td><td>16,0</td><td>18,0</td><td>21,5</td><td>2,60</td><td>0,56</td><td>1,8</td></tr>
<tr><td>8</td><td>12</td><td>2,90</td><td>3,70</td><td>4,50</td><td>5,50</td><td>7,00</td><td>7,50</td><td>8,50</td><td>9,0</td><td>10,5</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,5</td><td>19,0</td><td>22,0</td><td>26,0</td><td>3,25</td><td>0,45</td><td>2,4</td></tr>
<tr><td>9</td><td rowspan="4">190</td><td>3</td><td>2,55</td><td>3,05</td><td>3,55</td><td>4,05</td><td>5,00</td><td>5,50</td><td>6,00</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,0</td><td>15,0</td><td>17,5</td><td>2,00</td><td>0,90</td><td colspan="2" rowspan="4">60</td><td rowspan="4">36</td><td>0,9</td></tr>
<tr><td>10</td><td>5</td><td>2,65</td><td>3,30</td><td>3,95</td><td>4,65</td><td>6,00</td><td>6,50</td><td>7,00</td><td>8,0</td><td>9,0</td><td>10,0</td><td>12,0</td><td>13,0</td><td>14,5</td><td>16,0</td><td>18,0</td><td>21,5</td><td>2,60</td><td>0,70</td><td>1,3</td></tr>
<tr><td>11</td><td>8</td><td>2,85</td><td>3,65</td><td>4,45</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,50</td><td>9,0</td><td>10,5</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td>19,0</td><td>21,5</td><td>25,5</td><td>3,25</td><td>0,56</td><td>1,8</td></tr>
<tr><td>12</td><td>12</td><td>3,10</td><td>4,10</td><td>5,50</td><td>6,50</td><td>8,00</td><td>9,00</td><td>10,00</td><td>11,0</td><td>12,5</td><td>14,5</td><td>17,0</td><td>19,0</td><td>21,0</td><td>23,0</td><td>26,5</td><td>31,5</td><td>4,05</td><td>0,45</td><td>2,4</td></tr>
<tr><td>13</td><td rowspan="4">240</td><td>3</td><td>2,60</td><td>3,25</td><td>3,90</td><td>4,50</td><td>6,00</td><td>6,50</td><td>7,00</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,0</td><td>14,0</td><td>15,5</td><td>18,0</td><td>21,0</td><td>2,50</td><td>0,90</td><td colspan="2" rowspan="4">48</td><td rowspan="4">36</td><td>0,9</td></tr>
<tr><td>14</td><td>5</td><td>2,80</td><td>3,60</td><td>4,40</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,50</td><td>9,0</td><td>10,5</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td>19,0</td><td>21,5</td><td>25,5</td><td>3,25</td><td>0,70</td><td>1,3</td></tr>
<tr><td>15</td><td>8</td><td>3,00</td><td>4,00</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,50</td><td>10,00</td><td>11,0</td><td>12,5</td><td>14,5</td><td>17,0</td><td>19,0</td><td>21,0</td><td>23,0</td><td>26,5</td><td>31,5</td><td>4,05</td><td>0,56</td><td>1,8</td></tr>
<tr><td>16</td><td>12</td><td>3,30</td><td>4,55</td><td>6,00</td><td>7,00</td><td>9,00</td><td>10,00</td><td>11,50</td><td>12,5</td><td>14,5</td><td>17,0</td><td>20,0</td><td>22,5</td><td>25,0</td><td>27,5</td><td>31,5</td><td>38,0</td><td>5,00</td><td>0,45</td><td>2,4</td></tr>
<tr><td>17</td><td rowspan="4">300</td><td>3</td><td>2,70</td><td>3,50</td><td>4,30</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,00</td><td>9,0</td><td>10,0</td><td>12,0</td><td>14,0</td><td>15,5</td><td>17,0</td><td>18,5</td><td>21,5</td><td>25,5</td><td>3,20</td><td>0,90</td><td colspan="2" rowspan="4">38</td><td rowspan="4">36</td><td>0,9</td></tr>
<tr><td>18</td><td>5</td><td>2,90</td><td>3,95</td><td>4,95</td><td>6,00</td><td>7,50</td><td>8,50</td><td>9,50</td><td>10,5</td><td>12,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td>21,0</td><td>23,0</td><td>26,5</td><td>31,5</td><td>4,10</td><td>0,70</td><td>1,3</td></tr>
<tr><td>19</td><td>8</td><td>3,25</td><td>4,55</td><td>6,00</td><td>7,50</td><td>9,00</td><td>10,5</td><td>11,5</td><td>13,0</td><td>15,0</td><td>17,5</td><td>20,5</td><td>23,0</td><td>26,0</td><td>28,5</td><td>33,0</td><td>39,5</td><td>5,00</td><td>0,56</td><td>1,8</td></tr>
<tr><td>20</td><td>12</td><td>3,60</td><td>5,50</td><td>7,00</td><td>8,50</td><td>10,5</td><td>12,5</td><td>14,0</td><td>15,5</td><td>18,0</td><td>21,0</td><td>25,0</td><td>28,0</td><td>31,5</td><td>34,5</td><td>40,0</td><td>48,0</td><td>6,50</td><td>0,45</td><td>2,4</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="4%"><col width="6%"><col width="2%"><col width="1%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="29">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="29">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Борштанги двухопорные Единичное и мелкосерийное производство Резцы из стали Р6М5</td></tr>
<tr><td colspan="26">Карта 41</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td colspan="2">Глубина</td><td colspan="19">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td colspan="2">резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td colspan="2">150 175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td colspan="2">450</td><td colspan="2">500</td><td>600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td colspan="2">до</td><td colspan="19">Время на проход, мин.</td></tr>
<tr><td>21</td><td rowspan="8">10</td><td rowspan="4">380</td><td colspan="2">3</td><td>2,85</td><td>3,85</td><td>4,85</td><td>6,0</td><td>7,5</td><td colspan="2">8,5 9,5</td><td>10,5</td><td>12,0</td><td>14,0</td><td>16,5</td><td>18,5</td><td colspan="2">20,5</td><td colspan="2">22,5</td><td>26,0</td><td>31,5</td><td>4,05</td><td>0,90</td><td colspan="2" rowspan="4">306</td><td rowspan="4">36</td><td>0,9</td></tr>
<tr><td>22</td><td colspan="2">5</td><td>3,15</td><td>4,45</td><td>6,00</td><td>7,5</td><td>9,5</td><td colspan="2">10,5 11,5</td><td>13,0</td><td>15,0</td><td>17,5</td><td>20,5</td><td>23,0</td><td colspan="2">25,5</td><td colspan="2">28,5</td><td>32,5</td><td>39,0</td><td>5,00</td><td>0,70</td><td>1,3</td></tr>
<tr><td>23</td><td colspan="2">8</td><td>3,45</td><td>5,50</td><td>7,00</td><td>8,5</td><td>10,5</td><td colspan="2">12,0 14,0</td><td>15,5</td><td>18,0</td><td>21,0</td><td>24,5</td><td>28,0</td><td colspan="2">31,0</td><td colspan="2">34,5</td><td>39,5</td><td>47,5</td><td>6,50</td><td>0,56</td><td>1,8</td></tr>
<tr><td>24</td><td colspan="2">12</td><td>4,05</td><td>6,50</td><td>8,50</td><td>10,5</td><td>13,0</td><td colspan="2">15,0 17,5</td><td>19,5</td><td>22,5</td><td>27,0</td><td>31,5</td><td>35,5</td><td colspan="2">40,0</td><td colspan="2">44,0</td><td>51,0</td><td>62,0</td><td>8,00</td><td>0,45</td><td>2,4</td></tr>
<tr><td>25</td><td rowspan="4">480</td><td colspan="2">3</td><td>3,00</td><td>4,25</td><td>5,50</td><td>7,0</td><td>8,5</td><td colspan="2">10,0 11,0</td><td>12,5</td><td>14,0</td><td>16,5</td><td>19,5</td><td>22,0</td><td colspan="2">24,5</td><td colspan="2">27,0</td><td>31,5</td><td>37,5</td><td>5,00</td><td>0,90</td><td colspan="2" rowspan="4">24</td><td rowspan="4">36</td><td>0,9</td></tr>
<tr><td>26</td><td colspan="2">5</td><td>3,35</td><td>4,95</td><td>7,00</td><td>8,5</td><td>10,5</td><td colspan="2">12,0 13,5</td><td>15,5</td><td>17,5</td><td>21,0</td><td>24,5</td><td>28,0</td><td colspan="2">31,0</td><td colspan="2">34,0</td><td>39,5</td><td>47,5</td><td>6,50</td><td>0,70</td><td>1,3</td></tr>
<tr><td>27</td><td colspan="2">8</td><td>3,85</td><td>6,00</td><td>8,50</td><td>10,5</td><td>13,5</td><td colspan="2">15,0 17,0</td><td>19,5</td><td>22,5</td><td>26,5</td><td>31,5</td><td>35,5</td><td colspan="2">39,5</td><td colspan="2">44,0</td><td>51,0</td><td>61,0</td><td>8,00</td><td>0,56</td><td>1,8</td></tr>
<tr><td>28</td><td colspan="2">12</td><td>4,35</td><td>7,00</td><td>9,50</td><td>12,0</td><td>15,0</td><td colspan="2">17,5 20,0</td><td>22,5</td><td>26,0</td><td>31,0</td><td>36,5</td><td>41,5</td><td colspan="2">46,5</td><td colspan="2">52,0</td><td>60,0</td><td>72,0</td><td>10,00</td><td>0,45</td><td>2,4</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td colspan="2">н</td><td colspan="2">о</td><td>п</td><td>р</td><td>с</td><td colspan="5"></td></tr>
<tr><td colspan="29">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Группы медных сплавов, твердости</td><td colspan="7">Группа сплавов</td><td colspan="7">Гомогенные</td><td colspan="11">Гетерогенные</td></tr>
<tr><td colspan="4" rowspan="5">и продолжительности обработки</td><td colspan="7">Твердость НВ, ГПа</td><td colspan="7">0,59 - 0,88</td><td colspan="5">0,98 - 1,37</td><td colspan="6">1,47 - 2,45</td></tr>
<tr><td colspan="7">Продолжительность обработки, мин.</td><td colspan="7">до 10 свыше 10</td><td colspan="5">-</td><td colspan="2">до 10</td><td colspan="4">свыше 10</td></tr>
<tr><td colspan="7" rowspan="3">Коэффициент</td><td colspan="7" rowspan="3">0,7 0,55</td><td colspan="5"></td><td colspan="2" rowspan="3">1,1</td><td colspan="4" rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td colspan="3"></td></tr>
<tr><td colspan="5"></td></tr>
<tr><td colspan="4">Группы алюминиевых сплавов, твердости</td><td colspan="7">Группа сплавов</td><td colspan="7">Силумин и литейные сплавы</td><td colspan="11">Дюралюминий</td></tr>
<tr><td colspan="4" rowspan="3">и продолжительности обработки</td><td colspan="7">Твердость НВ, ГПа</td><td colspan="7">до 0,64</td><td colspan="11">до 0,98</td></tr>
<tr><td colspan="7">Продолжительность обработки, мин.</td><td colspan="7">до 10 свыше 10</td><td colspan="5">до 10</td><td colspan="6">свыше 10</td></tr>
<tr><td colspan="7">Коэффициент</td><td colspan="7">0,75 0,7</td><td colspan="5">0,75</td><td colspan="6">0,7</td></tr>
<tr><td colspan="4" rowspan="4">Состояния обрабатываемой поверхности</td><td colspan="7">Состояние обрабатываемой поверхности</td><td colspan="7">без корки</td><td colspan="11">по корке</td></tr>
<tr><td colspan="7" rowspan="3">Коэффициент</td><td colspan="7"></td><td colspan="11" rowspan="3">1,2</td></tr>
<tr><td>1,0</td><td colspan="6"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="4%"><col width="6%"><col width="2%"><col width="1%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="1%"><col width="2%"><col width="1%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="31">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Rz 20, 1Т9 квалитет</td></tr>
<tr><td colspan="31">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Резцы из стали Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="28">Карта 42</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td colspan="2">Глубина</td><td colspan="21">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td colspan="2">резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td colspan="2">175</td><td>200</td><td>250</td><td colspan="2">300</td><td>350</td><td>400</td><td colspan="2">450</td><td colspan="2">500</td><td>600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td colspan="2">до</td><td colspan="21">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">10</td><td>30</td><td colspan="2" rowspan="12">1</td><td>3,40</td><td>3,55</td><td>3,70</td><td>3,85</td><td></td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td></td><td>-</td><td>0,30</td><td colspan="2">750</td><td rowspan="12">70</td><td rowspan="12">до 1</td></tr>
<tr><td>2</td><td>48</td><td>3,40</td><td>3,55</td><td>3,75</td><td>3,90</td><td>4,45</td><td>4,6</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td></td><td>-</td><td rowspan="5">0,45</td><td colspan="2">480</td></tr>
<tr><td>3</td><td>60</td><td>3,45</td><td>3,65</td><td>3,85</td><td>4,05</td><td>4,60</td><td>4,8</td><td colspan="2">5,5</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td></td><td>-</td><td colspan="2">380</td></tr>
<tr><td>4</td><td>75</td><td>3,45</td><td>3,70</td><td>3,95</td><td>4,20</td><td>4,85</td><td>5,5</td><td colspan="2">5,5</td><td>6,0</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td></td><td>-</td><td colspan="2">300</td></tr>
<tr><td>5</td><td>96</td><td>3,50</td><td>3,80</td><td>4,15</td><td>4,45</td><td>5,50</td><td>5,5</td><td colspan="2">6,0</td><td>6,5</td><td>7,0</td><td colspan="2">7,5</td><td>-</td><td>-</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td></td><td>-</td><td colspan="2">240</td></tr>
<tr><td>6</td><td>120</td><td>3,55</td><td>3,95</td><td>4,35</td><td>4,75</td><td>6,00</td><td>6,0</td><td colspan="2">6,5</td><td>7,0</td><td>7,5</td><td colspan="2">8,5</td><td>10,0</td><td>10,5</td><td colspan="2">11,5</td><td colspan="2">12,5</td><td>14,5</td><td>16,5</td><td>1,30</td><td colspan="2">190</td></tr>
<tr><td>7</td><td>150</td><td>3,60</td><td>4,10</td><td>4,60</td><td>5,50</td><td>6,00</td><td>6,5</td><td colspan="2">7,5</td><td>8,0</td><td>8,5</td><td colspan="2">9,5</td><td>11,0</td><td>12,0</td><td colspan="2">13,0</td><td colspan="2">14,0</td><td>16,5</td><td>19,0</td><td>1,60</td><td rowspan="6"></td><td colspan="2">150</td></tr>
<tr><td>8</td><td>190</td><td>3,70</td><td>4,30</td><td>4,95</td><td>6,00</td><td>7,00</td><td>7,5</td><td colspan="2">8,0</td><td>8,5</td><td>9,5</td><td colspan="2">11,0</td><td>13,0</td><td>14,0</td><td colspan="2">15,5</td><td colspan="2">16,5</td><td>19,5</td><td>22,5</td><td>2,00</td><td colspan="2">120</td></tr>
<tr><td>9</td><td>240</td><td>3,80</td><td>4,60</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,5</td><td colspan="2">9,0</td><td>10,0</td><td>11,0</td><td colspan="2">13,0</td><td>15,0</td><td>16,5</td><td colspan="2">18,5</td><td colspan="2">20,0</td><td>23,0</td><td>27,0</td><td>2,50</td><td colspan="2">96</td></tr>
<tr><td>10</td><td>300</td><td>3,90</td><td>4,90</td><td>6,00</td><td>7,00</td><td>8,50</td><td>9,5</td><td colspan="2">10,5</td><td>11,5</td><td>13,0</td><td colspan="2">15,0</td><td>18,0</td><td>20,0</td><td colspan="2">22,0</td><td colspan="2">24,0</td><td>27,5</td><td>32,5</td><td>3,25</td><td colspan="2">75</td></tr>
<tr><td>11</td><td>380</td><td>4,05</td><td>5,50</td><td>6,50</td><td>8,00</td><td>9,50</td><td>11,0</td><td colspan="2">12,0</td><td>13,5</td><td>15,0</td><td colspan="2">17,5</td><td>21,0</td><td>23,5</td><td colspan="2">26,0</td><td colspan="2">28,5</td><td>33,0</td><td>39,0</td><td>4,05</td><td colspan="2">60</td></tr>
<tr><td>12</td><td>480</td><td>4,25</td><td>6,00</td><td>7,50</td><td>9,50</td><td>11,50</td><td>13,0</td><td colspan="2">14,5</td><td>16,0</td><td>18,0</td><td colspan="2">22,0</td><td>25,5</td><td>29,0</td><td colspan="2">32,0</td><td colspan="2">35,5</td><td>41,0</td><td>49,0</td><td>5,00</td><td colspan="2">48</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td colspan="2">н</td><td colspan="2">о</td><td>п</td><td>р</td><td>с</td><td colspan="5"></td></tr>
<tr><td colspan="31">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Группы медных сплавов, твердости</td><td colspan="8">Группа сплавов</td><td colspan="8">Гомогенные</td><td colspan="11">Гетерогенные</td></tr>
<tr><td colspan="4" rowspan="5">и продолжительности обработки</td><td colspan="8">Твердость НВ, ГПа</td><td colspan="8">0,59 - 0,88</td><td colspan="11">0,98 - 1,37 1,47 - 2,45</td></tr>
<tr><td colspan="8">Продолжительность обработки, мин.</td><td colspan="4">до 10</td><td colspan="4">свыше 10</td><td colspan="7">- до 10</td><td colspan="4">свыше 10</td></tr>
<tr><td colspan="8" rowspan="3">Коэффициент</td><td colspan="4" rowspan="3">0,7</td><td colspan="4" rowspan="3">0,55</td><td colspan="7"></td><td colspan="4" rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td colspan="5">1,1</td></tr>
</table>



<table>
<colgroup><col width="21%"><col width="36%"><col width="11%"><col width="3%"><col width="14%"><col width="2%"><col width="4%"><col width="9%"></colgroup>
<tr><td colspan="3">Неполное штучное время Растачивание отверстий, Rz 20, 1Т11 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="3" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Единичное и мелкосерийное производство</td><td colspan="5">Резцы из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 42</td><td colspan="2">Лист 2</td></tr>
<tr><td colspan="8">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td>Группы алюминиевых сплавов, твердости</td><td>Группа сплавов</td><td colspan="3">Силумин и литейные сплавы</td><td colspan="3">Дюралюминий</td></tr>
<tr><td rowspan="3">и продолжительности обработки</td><td>Твердость НВ, ГПа</td><td colspan="3">до 0,64</td><td colspan="3">до 0,98</td></tr>
<tr><td>Продолжительность обработки, мин.</td><td colspan="2">до 10</td><td>свыше 10</td><td colspan="2">до 10</td><td>свыше 10</td></tr>
<tr><td>Коэффициент</td><td colspan="2">0,75</td><td>0,7</td><td colspan="2">0,75</td><td>0,7</td></tr>
</table>


<a id="p101574"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету время по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="8%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="26">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Ra 2,5, 1Т9 - 1Т8 квалитет</td></tr>
<tr><td colspan="26">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Резцы из стали Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="23">Карта 43</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td>Глубина</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td>резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td>до</td><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">10</td><td>30</td><td rowspan="12">1</td><td>4,70</td><td>4,85</td><td>4,95</td><td>5,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td rowspan="12">0,22</td><td colspan="2">960</td><td>90</td><td rowspan="12">1</td></tr>
<tr><td>2</td><td>48</td><td>4,70</td><td>4,90</td><td>5,50</td><td>5,5</td><td>6,0</td><td>6,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">750</td><td rowspan="11">113</td></tr>
<tr><td>3</td><td>60</td><td>4,75</td><td>4,95</td><td>5,50</td><td>5,5</td><td>6,5</td><td>6,5</td><td>7,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">600</td></tr>
<tr><td>4</td><td>75</td><td>4,80</td><td>5,50</td><td>5,50</td><td>6,0</td><td>6,5</td><td>7,0</td><td>7,0</td><td>7,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">480</td></tr>
<tr><td>5</td><td>96</td><td>4,80</td><td>5,50</td><td>5,50</td><td>6,0</td><td>7,0</td><td>7,5</td><td>7,5</td><td>8,0</td><td>8,5</td><td>9,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">380</td></tr>
<tr><td>6</td><td>120</td><td>4,85</td><td>5,50</td><td>6,00</td><td>6,5</td><td>7,5</td><td>8,0</td><td>8,0</td><td>8,5</td><td>9,0</td><td>10,0</td><td>11,5</td><td>12,5</td><td>13,5</td><td>14,0</td><td>16,5</td><td>18,5</td><td>1,65</td><td colspan="2">300</td></tr>
<tr><td>7</td><td>150</td><td>4,90</td><td>5,50</td><td>6,00</td><td>6,5</td><td>8,0</td><td>8,5</td><td>9,0</td><td>9,5</td><td>10,0</td><td>11,0</td><td>13,0</td><td>14,0</td><td>15,0</td><td>16,0</td><td>18,5</td><td>21,0</td><td>2,08</td><td colspan="2">240</td></tr>
<tr><td>8</td><td>190</td><td>5,00</td><td>6,00</td><td>6,50</td><td>7,0</td><td>8,5</td><td>9,0</td><td>9,5</td><td>10,5</td><td>11,5</td><td>12,5</td><td>14,5</td><td>16,0</td><td>17,5</td><td>18,5</td><td>21,5</td><td>25,0</td><td>2,62</td><td colspan="2">190</td></tr>
<tr><td>9</td><td>240</td><td>5,50</td><td>6,00</td><td>7,00</td><td>7,5</td><td>9,0</td><td>9,5</td><td>10,5</td><td>11,0</td><td>12,0</td><td>13,5</td><td>16,0</td><td>17,5</td><td>19,0</td><td>20,5</td><td>23,5</td><td>27,0</td><td>3,32</td><td colspan="2">150</td></tr>
<tr><td>10</td><td>300</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,5</td><td>10,5</td><td>11,5</td><td>12,5</td><td>13,5</td><td>15,0</td><td>17,0</td><td>20,0</td><td>22,0</td><td>24,0</td><td>26,5</td><td>30,5</td><td>35,5</td><td>4,15</td><td colspan="2">120</td></tr>
<tr><td>11</td><td>380</td><td>5,50</td><td>7,00</td><td>8,00</td><td>9,5</td><td>11,5</td><td>12,5</td><td>14,0</td><td>15,5</td><td>17,5</td><td>20,0</td><td>23,5</td><td>26,0</td><td>28,5</td><td>31,0</td><td>36,0</td><td>42,5</td><td>5,18</td><td colspan="2">96</td></tr>
<tr><td>12</td><td>480</td><td>6,00</td><td>7,50</td><td>9,50</td><td>11,0</td><td>13,5</td><td>15,0</td><td>16,5</td><td>18,5</td><td>21,0</td><td>24,0</td><td>28,5</td><td>32,0</td><td>35,5</td><td>39,0</td><td>45,0</td><td>54,0</td><td>6,64</td><td colspan="2">75</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="19%"><col width="32%"><col width="12%"><col width="8%"><col width="4%"><col width="5%"><col width="7%"><col width="2%"><col width="4%"><col width="8%"></colgroup>
<tr><td colspan="4">Неполное штучное время Растачивание отверстий, Ra 2,5, 1Т9 - 1Т8 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="4" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Единичное и мелкосерийное производство</td><td colspan="6">Резцы из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 43</td><td colspan="2">Лист 2</td></tr>
<tr><td colspan="10">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td>Группы медных сплавов, твердости</td><td>Группа сплавов</td><td colspan="3">Гомогенные</td><td colspan="5">Гетерогенные</td></tr>
<tr><td rowspan="5">и продолжительности обработки</td><td>Твердость НВ, ГПа</td><td colspan="3">0,59 - 0,88</td><td colspan="2">0,98 - 1,37</td><td colspan="3">1,47 - 2,45</td></tr>
<tr><td>Продолжительность обработки, мин.</td><td>до 10</td><td colspan="2">свыше 10</td><td colspan="2">-</td><td colspan="2">до 10</td><td>свыше 10</td></tr>
<tr><td rowspan="3">Коэффициент</td><td rowspan="3">0,7</td><td colspan="2" rowspan="3">0,55</td><td colspan="2"></td><td colspan="2" rowspan="3">1,1</td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td>Группы алюминиевых сплавов, твердости</td><td>Группа сплавов</td><td colspan="3">Силумин и литейные сплавы</td><td colspan="5">Дюралюминий</td></tr>
<tr><td rowspan="3">и продолжительности обработки</td><td>Твердость НВ, ГПа</td><td colspan="3">до 0,64</td><td colspan="5">до 0,98</td></tr>
<tr><td>Продолжительность обработки, мин.</td><td>до 10</td><td colspan="2">свыше 10</td><td colspan="2">до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td>Коэффициент</td><td>0,75</td><td colspan="2">0,7</td><td colspan="2">0,75</td><td colspan="3">0,7</td></tr>
</table>


<a id="p101602"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету время по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="2%"><col width="2%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="8%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="28">Неполное штучное время Горизонтально-расточные станки Растачивание отверстий, Ra 2,5, 1Т7 квалитет</td></tr>
<tr><td colspan="28">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Резцы из стали Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="28">Карта 44</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td colspan="2">Глубина</td><td colspan="19">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>станка N , д кВт,</td><td colspan="2">резания t, мм,</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td colspan="2">175</td><td>200</td><td>250</td><td colspan="2">300</td><td>350</td><td>400</td><td>450</td><td>500</td><td>600</td><td>750</td><td>Добавлять на каждые 100 мм свыше 750</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>до</td><td colspan="2">до</td><td colspan="19">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">10</td><td>30</td><td colspan="2" rowspan="12">1,0</td><td>6,5</td><td>6,5</td><td>7,0</td><td>7,0</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td rowspan="12">0,12</td><td>1200</td><td>90</td><td rowspan="12">1</td></tr>
<tr><td>2</td><td>48</td><td>6,5</td><td>6,5</td><td>7,0</td><td>7,0</td><td>8,0</td><td>8,5</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>960</td><td>113</td></tr>
<tr><td>3</td><td>60</td><td>6,5</td><td>7,0</td><td>7,0</td><td>7,5</td><td>8,5</td><td>9,0</td><td colspan="2">9,0</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>750</td><td></td></tr>
<tr><td>4</td><td>75</td><td>6,5</td><td>7,0</td><td>7,5</td><td>7,5</td><td>9,0</td><td>9,0</td><td colspan="2">9,5</td><td>10,0</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>600</td><td></td></tr>
<tr><td>5</td><td>96</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,0</td><td>9,5</td><td>9,5</td><td colspan="2">10,0</td><td>10,5</td><td>11,5</td><td colspan="2">12,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>480</td><td></td></tr>
<tr><td>6</td><td>120</td><td>6,5</td><td>7,0</td><td>8,0</td><td>8,5</td><td>10,0</td><td>10,5</td><td colspan="2">11,0</td><td>11,5</td><td>12,5</td><td colspan="2">13,5</td><td>15,5</td><td>17,0</td><td>18</td><td>19,0</td><td>22,5</td><td>25,5</td><td>2,00</td><td>380</td><td></td></tr>
<tr><td>7</td><td>150</td><td>6,5</td><td>7,5</td><td>8,0</td><td>9,0</td><td>10,5</td><td>11,5</td><td colspan="2">12,0</td><td>13,0</td><td>14,0</td><td colspan="2">15,5</td><td>18,0</td><td>19,5</td><td>21</td><td>22,5</td><td>26,0</td><td>30,0</td><td>3,00</td><td>300</td><td></td></tr>
<tr><td>8</td><td>190</td><td>7,0</td><td>8,0</td><td>8,5</td><td>9,5</td><td>11,5</td><td>12,5</td><td colspan="2">13,5</td><td>14,0</td><td>15,5</td><td colspan="2">17,5</td><td>20,0</td><td>22,0</td><td>24</td><td>26,0</td><td>30,0</td><td>35,0</td><td>3,75</td><td>240</td><td></td></tr>
<tr><td>9</td><td>240</td><td>7,0</td><td>8,0</td><td>9,5</td><td>10,5</td><td>12,5</td><td>13,5</td><td colspan="2">15,0</td><td>16,0</td><td>18,0</td><td colspan="2">20,5</td><td>23,5</td><td>26,0</td><td>28</td><td>30,5</td><td>35,5</td><td>41,5</td><td>4,75</td><td>190</td><td></td></tr>
<tr><td>10</td><td>300</td><td>7,0</td><td>8,5</td><td>10,0</td><td>11,0</td><td>14,0</td><td>15,5</td><td colspan="2">17,0</td><td>18,5</td><td>21,0</td><td colspan="2">24,0</td><td>27,5</td><td>30,5</td><td>34</td><td>37,0</td><td>43,0</td><td>51,0</td><td>6,00</td><td>150</td><td></td></tr>
<tr><td>11</td><td>380</td><td>7,5</td><td>9,5</td><td>11,5</td><td>13,5</td><td>16,0</td><td>16,0</td><td colspan="2">20,0</td><td>22,0</td><td>25,0</td><td colspan="2">29,0</td><td>33,5</td><td>37,5</td><td>41</td><td>45,0</td><td>53,0</td><td>63,0</td><td>7,60</td><td>120</td><td></td></tr>
<tr><td>12</td><td>480</td><td>8,0</td><td>10,5</td><td>13,5</td><td>16,0</td><td>19,5</td><td>22,5</td><td colspan="2">25,0</td><td>28,0</td><td>32,0</td><td colspan="2">37,5</td><td>43,5</td><td>49,0</td><td>55</td><td>60,0</td><td>70,0</td><td>84,0</td><td>9,50</td><td>96</td><td></td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td><td>п</td><td>р</td><td>с</td><td colspan="4"></td></tr>
<tr><td colspan="28">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Группы медных сплавов, твердости</td><td colspan="8">Группа сплавов</td><td colspan="16">Гомогенные Гетерогенные</td></tr>
<tr><td colspan="4" rowspan="5">и продолжительности обработки</td><td colspan="8">Твердость НВ, ГПа</td><td colspan="11">0,59 - 0,88 0,98 - 1,37</td><td colspan="5">1,47 - 2,45</td></tr>
<tr><td colspan="8">Продолжительность обработки, мин.</td><td colspan="4">до 10</td><td colspan="7">свыше 10 -</td><td colspan="2">до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td colspan="8" rowspan="3">Коэффициент</td><td colspan="4" rowspan="3">0,7</td><td colspan="7"></td><td colspan="2" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td colspan="4">0,55</td><td colspan="3">1,0</td></tr>
<tr><td colspan="7"></td></tr>
<tr><td colspan="4">Группы алюминиевых сплавов, твердости</td><td colspan="8">Группа сплавов</td><td colspan="16">Силумин и литейные сплавы Дюралюминий</td></tr>
<tr><td colspan="4" rowspan="3">и продолжительности обработки</td><td colspan="8">Твердость НВ, ГПа</td><td colspan="16">до 0,64 до 0,98</td></tr>
<tr><td colspan="8">Продолжительность обработки, мин.</td><td colspan="4">до 10</td><td colspan="7">свыше 10 до 10</td><td colspan="5">свыше 10</td></tr>
<tr><td colspan="8">Коэффициент</td><td colspan="4">0,75</td><td colspan="7">0,7 0,75</td><td colspan="5">0,7</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="18">Неполное штучное время Горизонтально-расточные станки Продольное и поперечное точение, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="18">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Суппорт планшайбы Единичное и мелкосерийное производство Резцы из стали Р6М5</td></tr>
<tr><td colspan="14">Карта 45</td><td colspan="4">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="10">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемой поверхности D, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>Добавлять на каждые 100 мм свыше 250</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="10">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="20">10</td><td rowspan="3">120</td><td>3</td><td>1,45</td><td>1,75</td><td>2,30</td><td>2,65</td><td>3,15</td><td>3,50</td><td>3,80</td><td>4,15</td><td>4,95</td><td>1,30</td><td>0,56</td><td rowspan="3">150</td><td rowspan="20">57</td><td>0,5</td></tr>
<tr><td>2</td><td>5</td><td>1,50</td><td>1,90</td><td>2,55</td><td>2,95</td><td>3,60</td><td>4,00</td><td>4,40</td><td>4,80</td><td>6,00</td><td>1,60</td><td>0,45</td><td>1,5</td></tr>
<tr><td>3</td><td>8</td><td>1,65</td><td>2,15</td><td>2,90</td><td>3,45</td><td>4,20</td><td>4,70</td><td>5,50</td><td>6,00</td><td>7,00</td><td>2,10</td><td>0,35</td><td>2,0</td></tr>
<tr><td>4</td><td rowspan="3">150</td><td>3</td><td>1,50</td><td>1,90</td><td>2,50</td><td>2,95</td><td>3,55</td><td>3,95</td><td>4,35</td><td>4,80</td><td>6,00</td><td>1,65</td><td>0,56</td><td rowspan="3">120</td><td>0,5</td></tr>
<tr><td>5</td><td>5</td><td>1,60</td><td>2,10</td><td>2,80</td><td>3,30</td><td>4,05</td><td>4,55</td><td>5,50</td><td>6,00</td><td>7,00</td><td>2,05</td><td>0,45</td><td>1,5</td></tr>
<tr><td>6</td><td>8</td><td>1,75</td><td>2,40</td><td>3,25</td><td>3,90</td><td>4,80</td><td>5,50</td><td>6,50</td><td>7,00</td><td>8,50</td><td>2,60</td><td>0,35</td><td>2,0</td></tr>
<tr><td>7</td><td rowspan="3">190</td><td>3</td><td>1,55</td><td>2,05</td><td>2,80</td><td>3,30</td><td>4,00</td><td>4,50</td><td>5,00</td><td>6,00</td><td>7,00</td><td>2,05</td><td>0,56</td><td rowspan="3">96</td><td>0,5</td></tr>
<tr><td>8</td><td>5</td><td>1,70</td><td>2,30</td><td>3,15</td><td>3,80</td><td>4,65</td><td>5,50</td><td>6,00</td><td>7,00</td><td>8,00</td><td>2,55</td><td>0,45</td><td>1,5</td></tr>
<tr><td>9</td><td>8</td><td>1,90</td><td>2,70</td><td>3,75</td><td>4,60</td><td>6,00</td><td>6,50</td><td>7,50</td><td>8,50</td><td>10,00</td><td>3,25</td><td>0,35</td><td>2,0</td></tr>
<tr><td>10</td><td rowspan="3">240</td><td>3</td><td>1,65</td><td>2,30</td><td>3,15</td><td>3,80</td><td>4,70</td><td>5,50</td><td>6,00</td><td>7,00</td><td>8,00</td><td>2,60</td><td>0,56</td><td rowspan="3">75</td><td>0,5</td></tr>
<tr><td>11</td><td>5</td><td>1,80</td><td>2,60</td><td>3,60</td><td>4,45</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,00</td><td>9,50</td><td>3,25</td><td>0,45</td><td>1,5</td></tr>
<tr><td>12</td><td>8</td><td>2,05</td><td>3,10</td><td>4,40</td><td>5,50</td><td>7,00</td><td>8,00</td><td>9,00</td><td>10,00</td><td>12,00</td><td>4,15</td><td>0,35</td><td>2,0</td></tr>
<tr><td>13</td><td rowspan="3">300</td><td>3</td><td>1,75</td><td>2,55</td><td>3,60</td><td>4,45</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,00</td><td>10,00</td><td>3,25</td><td>0,56</td><td rowspan="3">60</td><td>0,5</td></tr>
<tr><td>14</td><td>5</td><td>1,95</td><td>2,95</td><td>4,20</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,50</td><td>9,50</td><td>11,50</td><td>4,05</td><td>0,45</td><td>1,5</td></tr>
<tr><td>15</td><td>8</td><td>2,25</td><td>3,55</td><td>5,50</td><td>6,50</td><td>8,00</td><td>9,50</td><td>10,50</td><td>12,00</td><td>14,50</td><td>5,00</td><td>0,35</td><td>2,0</td></tr>
<tr><td>16</td><td rowspan="3">380</td><td>3</td><td>1,85</td><td>2,85</td><td>4,10</td><td>5,50</td><td>6,50</td><td>7,50</td><td>8,50</td><td>9,50</td><td>11,50</td><td>4,05</td><td>0,56</td><td rowspan="3">48</td><td>0,5</td></tr>
<tr><td>17</td><td>5</td><td>2,15</td><td>3,45</td><td>4,95</td><td>6,50</td><td>8,00</td><td>9,50</td><td>10,50</td><td>12,00</td><td>14,00</td><td>5,00</td><td>0,45</td><td>1,5</td></tr>
<tr><td>18</td><td>8</td><td>2,50</td><td>4,10</td><td>6,00</td><td>8,00</td><td>9,50</td><td>11,00</td><td>13,00</td><td>14,50</td><td>17,00</td><td>6,50</td><td>0,35</td><td>2,0</td></tr>
<tr><td>19</td><td rowspan="2">480</td><td>3</td><td>2,05</td><td>3,35</td><td>4,85</td><td>6,50</td><td>8,00</td><td>9,00</td><td>10,50</td><td>12,00</td><td>14,00</td><td>5,00</td><td>0,56</td><td>57</td><td>0,5</td></tr>
<tr><td>20</td><td>5</td><td>2,35</td><td>3,95</td><td>6,00</td><td>7,50</td><td>9,50</td><td>11,00</td><td>12,50</td><td>14,5</td><td>17,00</td><td>6,50</td><td>0,45</td><td>38</td><td>1,5</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td></td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="7%"><col width="5%"><col width="5%"><col width="2%"><col width="4%"><col width="2%"><col width="3%"><col width="4%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="12">Неполное штучное время Продольное и поперечное точение, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="11">Горизонтально-расточные станки</td></tr>
<tr><td colspan="12" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Единичное и мелкосерийное производство</td><td colspan="11">Суппорт планшайбы Резцы из стали Р6М5</td></tr>
<tr><td colspan="6">Карта 45</td><td colspan="5">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td colspan="2" rowspan="3">Глубина резания, t, мм, до</td><td colspan="13">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемой поверхности D, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td colspan="2">125 150</td><td colspan="3">175 200</td><td colspan="2">250</td><td colspan="2">Добавлять на каждые 100 мм свыше 250</td><td colspan="2" rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="13">Время на проход, мин.</td></tr>
<tr><td>21</td><td rowspan="4">10</td><td>480</td><td colspan="2">8</td><td>2,85</td><td>5,00</td><td>7,5</td><td>9,5</td><td colspan="2">12,0 14,0</td><td colspan="3">16,0 18,5</td><td colspan="2">22,0</td><td colspan="2">8,0</td><td colspan="2">0,35</td><td rowspan="4">30</td><td rowspan="4">57</td><td>2,0</td></tr>
<tr><td>22</td><td rowspan="3">600</td><td colspan="2">3</td><td>2,25</td><td>3,85</td><td>6,0</td><td>7,5</td><td colspan="2">9,5 11,0</td><td colspan="3">12,5 14,0</td><td colspan="2">17,0</td><td colspan="2">6,5</td><td colspan="2">0,56</td><td>0,5</td></tr>
<tr><td>23</td><td colspan="2">5</td><td>2,70</td><td>4,80</td><td>7,5</td><td>9,5</td><td colspan="2">12,0 14,0</td><td colspan="3">16,0 18,0</td><td colspan="2">21,5</td><td colspan="2">8,0</td><td colspan="2">0,45</td><td>1,5</td></tr>
<tr><td>24</td><td colspan="2">8</td><td>3,35</td><td>6,50</td><td>9,5</td><td>12,0</td><td colspan="2">15,0 17,5</td><td colspan="3">20,5 23,0</td><td colspan="2">27,5</td><td colspan="2">10,5</td><td colspan="2">0,35</td><td>2,0</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д е</td><td colspan="3">ж з</td><td colspan="2">и</td><td colspan="2">к</td><td colspan="5"></td></tr>
<tr><td colspan="23">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Группы медных сплавов, твердости</td><td colspan="6">Группа сплавов</td><td colspan="5">Гомогенные</td><td colspan="8">Гетерогенные</td></tr>
<tr><td colspan="4" rowspan="5">и продолжительности обработки</td><td colspan="6">Твердость НВ, ГПа</td><td colspan="5">0,59 - 0,88</td><td colspan="4">0,98 - 1,37</td><td colspan="4">1,47 - 2,45</td></tr>
<tr><td colspan="6">Продолжительность обработки, мин.</td><td colspan="5">до 10 свыше 10</td><td colspan="4">-</td><td colspan="4">до 10 свыше 10</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="5" rowspan="3">0,7 0,55</td><td colspan="4"></td><td colspan="4" rowspan="3">1,1 1,25</td></tr>
<tr><td colspan="2">1,0</td><td colspan="2"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td colspan="4">Группы алюминиевых сплавов, твердости и продолжительности</td><td colspan="6">Группа сплавов</td><td colspan="5">Силумин и литейные сплавы</td><td colspan="8">Дюралюминий</td></tr>
<tr><td colspan="4" rowspan="3">обработки</td><td colspan="6">Твердость НВ, ГПа</td><td colspan="5">до 0,64</td><td colspan="8">до 0,98</td></tr>
<tr><td colspan="6">Продолжительность обработки</td><td colspan="2">до 10</td><td colspan="3">свыше 10</td><td colspan="5">до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td colspan="6">Коэффициент</td><td colspan="2">0,75</td><td colspan="3">0,7</td><td colspan="5">0,75</td><td colspan="3">0,7</td></tr>
<tr><td colspan="4" rowspan="5">Вида обработки</td><td colspan="8">Продольное и поперечное точение</td><td colspan="11">Растачивание</td></tr>
<tr><td colspan="19">Коэффициент</td></tr>
<tr><td colspan="8"></td><td colspan="11" rowspan="3">1,06</td></tr>
<tr><td>1,0</td><td colspan="7"></td></tr>
<tr><td colspan="8"></td></tr>
<tr><td colspan="4" rowspan="4">Состояние обрабатываемой поверхности</td><td colspan="8">Состояние обрабатываемой поверхности</td><td colspan="11">без корки по корке</td></tr>
<tr><td colspan="8" rowspan="3">Коэффициент</td><td colspan="11"></td></tr>
<tr><td>1,0</td><td colspan="10">1,2</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="4%"><col width="6%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="12">Неполное штучное время Продольное и поперечное точение, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="12" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Единичное и мелкосерийное производство</td><td colspan="7">Суппорт планшайбы Резцы из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 46</td><td colspan="4">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Глубина резания, t, мм</td><td colspan="11">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемой поверхности D, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td colspan="2">200</td><td>250</td><td>Добавлять на каждые 100 мм свыше 250</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="11">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="8">10</td><td>120</td><td rowspan="8">1</td><td>1,65</td><td>1,90</td><td>2,25</td><td>2,45</td><td>2,90</td><td>3,15</td><td>3,35</td><td colspan="2">3,60</td><td>4,25</td><td>0,90</td><td rowspan="8">0,50</td><td>240</td><td rowspan="8">90</td><td rowspan="8">2,1</td></tr>
<tr><td>2</td><td>150</td><td>1,75</td><td>2,00</td><td>2,40</td><td>2,70</td><td>3,20</td><td>3,50</td><td>3,80</td><td colspan="2">4,05</td><td>4,85</td><td>1,15</td><td>190</td></tr>
<tr><td>3</td><td>190</td><td>1,75</td><td>2,15</td><td>2,60</td><td>2,95</td><td>3,55</td><td>3,90</td><td>4,30</td><td colspan="2">4,65</td><td>6,00</td><td>1,45</td><td>150</td></tr>
<tr><td>4</td><td>240</td><td>1,80</td><td>2,30</td><td>2,85</td><td>3,30</td><td>4,00</td><td>4,45</td><td>4,90</td><td colspan="2">5,50</td><td>6,50</td><td>1,80</td><td>120</td></tr>
<tr><td>5</td><td>300</td><td>1,90</td><td>2,45</td><td>3,15</td><td>3,70</td><td>4,50</td><td>5,50</td><td>6,00</td><td colspan="2">6,50</td><td>7,50</td><td>2,30</td><td>96</td></tr>
<tr><td>6</td><td>380</td><td>2,00</td><td>2,75</td><td>3,60</td><td>4,30</td><td>5,50</td><td>6,00</td><td>7,00</td><td colspan="2">7,50</td><td>9,00</td><td>2,90</td><td>75</td></tr>
<tr><td>7</td><td>480</td><td>2,10</td><td>3,00</td><td>4,00</td><td>4,95</td><td>6,50</td><td>7,00</td><td>8,00</td><td colspan="2">9,00</td><td>10,5</td><td>3,65</td><td>60</td></tr>
<tr><td>8</td><td>600</td><td>2,20</td><td>3,35</td><td>4,60</td><td>6,00</td><td>7,50</td><td>8,50</td><td>9,50</td><td colspan="2">11,00</td><td>13,00</td><td>4,55</td><td>48</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="22%"><col width="5%"><col width="29%"><col width="11%"><col width="5%"><col width="5%"><col width="6%"><col width="2%"><col width="14%"></colgroup>
<tr><td colspan="4">Неполное штучное время Продольное и поперечное точение, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="4" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Единичное и мелкосерийное производство</td><td colspan="5">Суппорт планшайбы Резцы из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 46</td><td colspan="2">Лист 2</td></tr>
<tr><td colspan="9">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="5">Группы медных сплавов, твердости</td><td colspan="2">Группа сплавов</td><td colspan="2">Гомогенные</td><td colspan="4">Гетерогенные</td></tr>
<tr><td colspan="2">Твердость НВ, ГПа</td><td colspan="2">0,59 - 0,88</td><td colspan="3">0,98 - 1,37</td><td>1,47 - 2,45</td></tr>
<tr><td colspan="2" rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,55</td><td colspan="3"></td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td rowspan="3">Группы алюминиевых сплавов, твердости</td><td colspan="2">Группа сплавов</td><td colspan="5">Силумин и литейные сплавы</td><td>Дюралюминий</td></tr>
<tr><td colspan="2">Твердость НВ, ГПа</td><td colspan="5">до 0,64</td><td>до 0,98</td></tr>
<tr><td colspan="2">Коэффициент</td><td colspan="5">0,75</td><td>0,7</td></tr>
<tr><td rowspan="5">Вида обработки</td><td colspan="2">Продольное и поперечное точение</td><td colspan="6">Растачивание</td></tr>
<tr><td colspan="8">Коэффициент</td></tr>
<tr><td colspan="2"></td><td colspan="6" rowspan="3">1,06</td></tr>
<tr><td>1,0</td><td></td></tr>
</table>


<a id="p101695"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="11">Неполное штучное время Продольное и поперечное точение, Ra 2,5, 1Т9 - 1Т8 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="11" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Единичное и мелкосерийное производство</td><td colspan="7">Суппорт планшайбы Резцы из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 47</td><td colspan="4">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="10">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемой поверхности D, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>250</td><td>Добавлять на каждые 100 мм свыше 250</td><td rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="10">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="8">10</td><td>120</td><td rowspan="8">1,0</td><td>2,85</td><td>3,15</td><td>3,60</td><td>3,95</td><td>4,6</td><td>4,9</td><td>5,5</td><td>6,0</td><td>6,5</td><td>1,30</td><td rowspan="8">0,22</td><td>380</td><td rowspan="8">140</td><td rowspan="8">2,1</td></tr>
<tr><td>2</td><td>150</td><td>2,90</td><td>3,30</td><td>3,85</td><td>4,25</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>1,65</td><td>300</td></tr>
<tr><td>3</td><td>190</td><td>2,95</td><td>3,45</td><td>4,10</td><td>4,60</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td>2,05</td><td>240</td></tr>
<tr><td>4</td><td>240</td><td>3,05</td><td>3,70</td><td>4,45</td><td>5,50</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>2,60</td><td>190</td></tr>
<tr><td>5</td><td>300</td><td>3,15</td><td>3,95</td><td>4,90</td><td>6,00</td><td>7,0</td><td>8,0</td><td>9,0</td><td>9,5</td><td>11,0</td><td>3,30</td><td>150</td></tr>
<tr><td>6</td><td>380</td><td>3,25</td><td>4,30</td><td>5,50</td><td>7,00</td><td>8,0</td><td>9,0</td><td>10,0</td><td>11,5</td><td>13,0</td><td>4,15</td><td>120</td></tr>
<tr><td>7</td><td>480</td><td>3,40</td><td>4,70</td><td>6,50</td><td>7,50</td><td>9,5</td><td>10,5</td><td>12,0</td><td>13,0</td><td>15,5</td><td>5,00</td><td>96</td></tr>
<tr><td>8</td><td>600</td><td>3,65</td><td>5,50</td><td>7,50</td><td>9,00</td><td>11,0</td><td>13,0</td><td>14,5</td><td>16,5</td><td>19,0</td><td>6,50</td><td>75</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="21%"><col width="5%"><col width="25%"><col width="8%"><col width="5%"><col width="6%"><col width="5%"><col width="8%"><col width="7%"><col width="9%"></colgroup>
<tr><td colspan="5">Неполное штучное время Продольное и поперечное точение, Ra 2,5, 1Т9 - 1Т8 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="5" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Единичное и мелкосерийное производство</td><td colspan="5">Суппорт планшайбы Резцы из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 47</td><td colspan="2">Лист 2</td></tr>
<tr><td colspan="10">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td>Группы медных сплавов, твердости</td><td colspan="2">Группа сплавов</td><td colspan="3">Гомогенные</td><td colspan="4">Гетерогенные</td></tr>
<tr><td rowspan="5">и продолжительности обработки</td><td colspan="2">Твердость НВ, ГПа</td><td colspan="3">0,59 - 0,88</td><td colspan="2">0,98 - 1,37</td><td colspan="2">1,47 - 2,45</td></tr>
<tr><td colspan="2">Продолжительность обработки, мин.</td><td>до 10</td><td colspan="2">свыше 10</td><td colspan="2">-</td><td>до 10</td><td>свыше 10</td></tr>
<tr><td colspan="2" rowspan="3">Коэффициент</td><td rowspan="3">0,7</td><td colspan="2" rowspan="3">0,55</td><td colspan="2"></td><td rowspan="3">1,1</td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td>Группы алюминиевых сплавов, твердости и продолжительности</td><td colspan="2">Группа сплавов</td><td colspan="3">Силумин и литейные сплавы</td><td colspan="4">Дюралюминий</td></tr>
<tr><td rowspan="3">обработки</td><td colspan="2">Твердость НВ, ГПа</td><td colspan="3">до 0,64</td><td colspan="4">до 0,98</td></tr>
<tr><td colspan="2">Продолжительность обработки</td><td>до 10</td><td colspan="2">свыше 10</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td></tr>
<tr><td colspan="2">Коэффициент</td><td>0,75</td><td colspan="2">0,7</td><td colspan="2">0,75</td><td colspan="2">0,7</td></tr>
<tr><td rowspan="5">Вида обработки</td><td colspan="5">Продольное и поперечное точение</td><td colspan="4">Растачивание</td></tr>
<tr><td colspan="9">Коэффициент</td></tr>
<tr><td colspan="5"></td><td colspan="4" rowspan="3">1,06</td></tr>
<tr><td>1,0</td><td colspan="4"></td></tr>
</table>


<a id="p101722"></a>*Примечание.* При обработке с шероховатостью поверхности Ra 2,5 по 1Т14 - 1Т12 квалитету по карте уменьшать на величину:


| Длина обрабатываемой поверхности, мм | до 100 | свыше 100 |
| --- | --- | --- |
| Время, мин. | 1,5 | 1,8 |



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="2%"><col width="5%"><col width="5%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="5%"><col width="2%"><col width="3%"><col width="2%"><col width="5%"><col width="2%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="23">Неполное штучное время Горизонтально-расточные станки Продольное и поперечное точение, Ra 1,25, 1Т7 квалитет</td></tr>
<tr><td colspan="23">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Резцы из стали Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="23">Карта 48</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td colspan="2" rowspan="3">Глубина резания, t, мм, до</td><td colspan="13">Длина обрабатываемой поверхности l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">обрабатываемой поверхности D, мм, до</td><td>25</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td colspan="2">175</td><td>200</td><td colspan="2">250</td><td colspan="2">Добавлять на каждые 100 мм свыше 250</td><td colspan="2" rowspan="2">S , о мм/ об.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="13">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="8">10</td><td>120</td><td colspan="2" rowspan="8">1</td><td>3,90</td><td>4,4</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td colspan="2">7,5</td><td>8,0</td><td colspan="2">9,5</td><td colspan="2">1,90</td><td colspan="2" rowspan="8">0,15</td><td>380</td><td rowspan="8">140</td><td rowspan="8">2,0</td></tr>
<tr><td>2</td><td>150</td><td>4,00</td><td>4,6</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,0</td><td colspan="2">8,5</td><td>9,0</td><td colspan="2">10,5</td><td colspan="2">2,45</td><td>300</td></tr>
<tr><td>3</td><td>190</td><td>4,10</td><td>4,9</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10,0</td><td>10,5</td><td colspan="2">12,5</td><td colspan="2">3,05</td><td>240</td></tr>
<tr><td>4</td><td>240</td><td>4,20</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,0</td><td colspan="2">11,0</td><td>13,0</td><td colspan="2">14,0</td><td colspan="2">3,85</td><td>190</td></tr>
<tr><td>5</td><td>300</td><td>4,35</td><td>6,0</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td colspan="2">12,5</td><td>14,0</td><td colspan="2">16,5</td><td colspan="2">4,85</td><td>150</td></tr>
<tr><td>6</td><td>380</td><td>4,50</td><td>6,5</td><td>8,0</td><td>9,5</td><td>11,5</td><td>13,0</td><td colspan="2">14,5</td><td>16,0</td><td colspan="2">19,0</td><td colspan="2">6,00</td><td>120</td></tr>
<tr><td>7</td><td>480</td><td>4,75</td><td>7,0</td><td>9,0</td><td>11,0</td><td>13,5</td><td>15,5</td><td colspan="2">17,5</td><td>19,5</td><td colspan="2">22,5</td><td colspan="2">7,50</td><td>96</td></tr>
<tr><td>8</td><td>600</td><td>5,50</td><td>8,0</td><td>10,5</td><td>13,0</td><td>16,0</td><td>18,5</td><td colspan="2">21,0</td><td>23,5</td><td colspan="2">27,5</td><td colspan="2">9,50</td><td>75</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td colspan="2">и</td><td colspan="2">к</td><td colspan="5"></td></tr>
<tr><td colspan="23">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Группы медных сплавов, твердости</td><td colspan="6">Группа сплавов</td><td colspan="5">Гомогенные</td><td colspan="8">Гетерогенные</td></tr>
<tr><td colspan="4" rowspan="5">и продолжительности обработки</td><td colspan="6">Твердость НВ, ГПа</td><td colspan="5">0,59 - 0,88</td><td colspan="4">0,98 - 1,37</td><td colspan="4">1,47 - 2,45</td></tr>
<tr><td colspan="6">Продолжительность обработки, мин.</td><td colspan="2">до 10</td><td colspan="3">свыше 10</td><td colspan="4">-</td><td colspan="4">до 10 свыше 10</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,7</td><td colspan="3" rowspan="3">0,55</td><td colspan="4"></td><td colspan="4" rowspan="3">1,1 1,25</td></tr>
<tr><td colspan="2">1,0</td><td colspan="2"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td colspan="4">Группы алюминиевых сплавов, твердости и продолжительности</td><td colspan="6">Группа сплавов</td><td colspan="5">Силумин и литейные сплавы</td><td colspan="8">Дюралюминий</td></tr>
<tr><td colspan="4" rowspan="3">обработки</td><td colspan="6">Твердость НВ, ГПа</td><td colspan="5">до 0,64</td><td colspan="8">до 0,98</td></tr>
<tr><td colspan="6">Продолжительность обработки, мин.</td><td colspan="2">до 10</td><td colspan="3">свыше 10</td><td colspan="4">до 10</td><td colspan="4">свыше 10</td></tr>
<tr><td colspan="6">Коэффициент</td><td colspan="2">0,75</td><td colspan="3">0,7</td><td colspan="4">0,75</td><td colspan="4">0,7</td></tr>
<tr><td colspan="4" rowspan="5">Вид обработки</td><td colspan="6">Продольное и поперечное точение</td><td colspan="13">Растачивание</td></tr>
<tr><td colspan="19">Коэффициент</td></tr>
<tr><td colspan="6"></td><td colspan="13" rowspan="3">1,06</td></tr>
<tr><td>1,0</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="12%"><col width="11%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="5%"><col width="7%"><col width="5%"><col width="5%"><col width="4%"><col width="5%"><col width="8%"><col width="8%"></colgroup>
<tr><td colspan="10">Неполное штучное время Прорезка канавок Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td><td colspan="5">Горизонтальнорасточные станки</td></tr>
<tr><td colspan="10" rowspan="2">Единичное и мелкосерийное производство</td><td colspan="5">Суппорт планшайбы Резцы из стали Р6М5</td></tr>
<tr><td colspan="5">Карта 49</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр обрабатываемой поверхности D, мм, до</td><td>Ширина резца,</td><td colspan="7">Глубина канавки l, мм, до</td><td colspan="5">Режим резания</td></tr>
<tr><td rowspan="2">В, мм</td><td>3</td><td>4,5</td><td>6</td><td>8</td><td>10</td><td>12</td><td>15</td><td colspan="2" rowspan="2">S , о мм/об.</td><td colspan="2" rowspan="2">v, м/мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="7">Время на поверхность, мин.</td></tr>
<tr><td>1</td><td>50</td><td>3 - 5</td><td>2,3</td><td>2,4</td><td>2,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2" rowspan="3">0,08</td><td colspan="2">94</td><td rowspan="11">1</td></tr>
<tr><td>2</td><td>75</td><td>3 - 5</td><td>2,3</td><td>2,4</td><td>2,5</td><td>2,5</td><td>2,6</td><td>-</td><td>-</td><td colspan="2">125</td></tr>
<tr><td>3</td><td>100</td><td rowspan="2">5 - 8</td><td>2,4</td><td>2,5</td><td>2,5</td><td>2,6</td><td>2,7</td><td>2,8</td><td>2,9</td><td colspan="2"></td></tr>
<tr><td>4</td><td>125</td><td>2,5</td><td>2,6</td><td>2,6</td><td>2,7</td><td>2,8</td><td>2,9</td><td>3,0</td><td colspan="2" rowspan="5">0,1</td><td colspan="2">117</td></tr>
<tr><td>5</td><td>150</td><td rowspan="7">10 - 12</td><td>2,6</td><td>2,7</td><td>2,7</td><td>2,8</td><td>3,0</td><td>3,1</td><td>3,2</td><td colspan="2">110 - 125</td></tr>
<tr><td>6</td><td>200</td><td>2,6</td><td>2,7</td><td>2,8</td><td>3,0</td><td>3,1</td><td>3,2</td><td>3,4</td><td colspan="2" rowspan="2">117</td></tr>
<tr><td>7</td><td>250</td><td>2,7</td><td>2,8</td><td>2,9</td><td>3,1</td><td>3,2</td><td>3,4</td><td>3,6</td></tr>
<tr><td>8</td><td>300</td><td>2,8</td><td>2,9</td><td>3,1</td><td>3,2</td><td>3,5</td><td>3,7</td><td>3,9</td><td colspan="2">110</td></tr>
<tr><td>9</td><td>400</td><td>2,9</td><td>3,0</td><td>3,1</td><td>3,3</td><td>3,6</td><td>3,8</td><td>4,0</td><td colspan="2" rowspan="3">0,12</td><td colspan="2">100 - 113</td></tr>
<tr><td>10</td><td>500</td><td>3,1</td><td>3,2</td><td>3,4</td><td>3,6</td><td>4,0</td><td>4,3</td><td>4,6</td><td colspan="2">94</td></tr>
<tr><td>11</td><td>600</td><td>3,3</td><td>3,4</td><td>3,6</td><td>4,0</td><td>4,4</td><td>4,7</td><td>5,0</td><td colspan="2">86 - 95</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="5"></td></tr>
<tr><td colspan="15">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="7">Группы медных Группа сплавов сплавов и твердости</td><td colspan="8">Гомогенные Гетерогенные</td></tr>
<tr><td colspan="7" rowspan="2">Твердость НВ, ГПа</td><td colspan="6">0,59 - 0,88 0,98 - 1,37</td><td colspan="2">1,47 - 2,45</td></tr>
<tr><td colspan="6"></td><td colspan="2" rowspan="3">1,25</td></tr>
<tr><td colspan="7" rowspan="2">Коэффициент</td><td colspan="3">0,55</td><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="6"></td></tr>
<tr><td colspan="7">Группы алюминиевых Группа сплавов сплавов и твердости</td><td colspan="6">Силумин и литейные сплавы</td><td colspan="2">Дюралюминий</td></tr>
<tr><td colspan="7">Твердость НВ, ГПа</td><td colspan="6">до 0,64</td><td colspan="2">до 0,9</td></tr>
<tr><td colspan="7">Коэффициент</td><td colspan="6">0,75</td><td colspan="2">0,7</td></tr>
</table>


<a id="p101769"></a>*Примечание.* При обработке внутренних канавок и канавок на торце время по карте принимать с коэффициентом К = 1,15.


<table>
<colgroup><col width="5%"><col width="12%"><col width="5%"><col width="6%"><col width="6%"><col width="5%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="6%"><col width="6%"><col width="3%"><col width="4%"><col width="6%"><col width="5%"></colgroup>
<tr><td colspan="9">Неполное штучное время Обработка фасок и радиусов</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="9">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td><td colspan="8">Резцы из стали Р6М5</td></tr>
<tr><td colspan="9">Единичное и мелкосерийное производство</td><td colspan="8">Карта 50</td></tr>
<tr><td rowspan="5">N позиции</td><td rowspan="2">Диаметр обрабатываемой поверхности D,</td><td colspan="7">Обработка фасок</td><td colspan="8">Обработка радиусов</td></tr>
<tr><td colspan="4">Резцы из стали Р5М5</td><td colspan="3">Режимы резания</td><td colspan="4">Резцы из стали Р6М5</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="3">мм, до</td><td colspan="4">Ширина фаски, мм, до</td><td rowspan="3">S , м мм/ об.</td><td rowspan="3">v, м/ мин.</td><td rowspan="3">N , р кВт, до</td><td colspan="4">Размер радиуса, мм, до</td><td colspan="2" rowspan="3">S , м мм/ мин.</td><td rowspan="3">v, м/ мин.</td><td rowspan="3">N , р кВт</td></tr>
<tr><td>3</td><td>5</td><td>8</td><td>10</td><td>3</td><td>5</td><td>8</td><td>10</td></tr>
<tr><td colspan="4">Время на поверхность, мин.</td><td colspan="4">Время на поверхность, мин.</td></tr>
<tr><td>1</td><td>50</td><td>0,7</td><td>0,80</td><td>1,0</td><td>1,2</td><td>18,0</td><td rowspan="7">95</td><td rowspan="7">1</td><td>1,7</td><td>1,9</td><td>2,1</td><td>2,3</td><td colspan="2">12,0</td><td rowspan="7">95</td><td rowspan="7">1</td></tr>
<tr><td>2</td><td>100</td><td>0,8</td><td>0,90</td><td>1,1</td><td>1,3</td><td>15,0</td><td>1,9</td><td>2,1</td><td>2,4</td><td>2,6</td><td colspan="2">10,0</td></tr>
<tr><td>3</td><td>200</td><td>0,9</td><td>1,10</td><td>1,3</td><td>1,6</td><td>10,0</td><td>2,0</td><td>2,3</td><td>2,8</td><td>3,2</td><td colspan="2">7,0</td></tr>
<tr><td>4</td><td>300</td><td>1,0</td><td>1,25</td><td>1,6</td><td>2,0</td><td>7,5</td><td>2,3</td><td>2,7</td><td>3,4</td><td>3,8</td><td colspan="2">5,0</td></tr>
<tr><td>5</td><td>400</td><td>1,1</td><td>1,45</td><td>1,8</td><td>2,4</td><td>6,0</td><td>2,5</td><td>3,1</td><td>3,8</td><td>4,4</td><td colspan="2">4,0</td></tr>
<tr><td>6</td><td>500</td><td>1,2</td><td>1,60</td><td>2,1</td><td>2,7</td><td>5,0</td><td>2,7</td><td>3,3</td><td>4,2</td><td>4,8</td><td colspan="2">3,5</td></tr>
<tr><td>7</td><td>600</td><td>1,4</td><td>1,90</td><td>2,5</td><td>3,3</td><td>4,0</td><td>2,9</td><td>3,6</td><td>4,7</td><td>5,3</td><td colspan="2">3,0</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="3"></td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="4"></td></tr>
<tr><td colspan="17">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="17">Группы медных Группа сплавов Гомогенные Гетерогенные</td></tr>
<tr><td colspan="14">твердости Твердость НВ, ГПа 0,59 - 0,88 0,98 - 1,37</td><td colspan="3">1,47 - 2,45</td></tr>
<tr><td colspan="14"></td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td colspan="11">Коэффициент 0,55</td><td colspan="3">1,0</td></tr>
<tr><td colspan="14"></td></tr>
<tr><td colspan="17">Группы Группа сплавов Силумин и Дюралюминий алюминиевых литейные сплавы</td></tr>
<tr><td colspan="17">твердости Твердость НВ, ГПа до 0,64 до 0,98</td></tr>
<tr><td colspan="17">Коэффициент 0,75 0,7</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="12%"><col width="8%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="8%"><col width="8%"><col width="8%"><col width="9%"><col width="9%"></colgroup>
<tr><td colspan="10">Неполное штучное время Подрезка торцов Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td><td colspan="3">Горизонтальнорасточные станки</td></tr>
<tr><td colspan="10" rowspan="2">Единичное и мелкосерийное производство</td><td colspan="3">Резцы из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 51</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обрабатываемой</td><td colspan="8">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td>поверхности D,</td><td>3</td><td>5</td><td>8</td><td colspan="2">10</td><td>12</td><td>15</td><td>20</td><td>S , о</td><td rowspan="2">v, м/мин.</td><td>N , р</td></tr>
<tr><td>мм, до</td><td colspan="8">Время на поверхность, мин.</td><td>мм/ мин.</td><td>кВт, до</td></tr>
<tr><td>1</td><td>75</td><td>0,80</td><td>0,90</td><td>1,0</td><td colspan="2">1,2</td><td>1,35</td><td>1,5</td><td>1,7</td><td>17,5</td><td rowspan="9">6,0</td><td rowspan="9">1,0</td></tr>
<tr><td>2</td><td>125</td><td>0,95</td><td>1,15</td><td>1,3</td><td colspan="2">1,5</td><td>1,70</td><td>1,9</td><td>2,2</td><td>14,0</td></tr>
<tr><td>3</td><td>150</td><td>1,00</td><td>1,20</td><td>1,5</td><td colspan="2">1,7</td><td>1,90</td><td>2,1</td><td>2,5</td><td>11,5</td></tr>
<tr><td>4</td><td>175</td><td>1,10</td><td>1,30</td><td>1,6</td><td colspan="2">1,9</td><td>2,10</td><td>2,4</td><td>2,8</td><td>10,0</td></tr>
<tr><td>5</td><td>200</td><td>1,20</td><td>1,40</td><td>1,7</td><td colspan="2">2,0</td><td>2,20</td><td>2,5</td><td>3,0</td><td>9,0</td></tr>
<tr><td>6</td><td>225</td><td>1,20</td><td>1,50</td><td>1,8</td><td colspan="2">2,2</td><td>2,40</td><td>2,8</td><td>3,3</td><td>8,0</td></tr>
<tr><td>7</td><td>250</td><td>1,30</td><td>1,60</td><td>2,0</td><td colspan="2">2,4</td><td>2,70</td><td>3,1</td><td>3,7</td><td>7,0</td></tr>
<tr><td>8</td><td>275</td><td>1,30</td><td>1,70</td><td>2,1</td><td colspan="2">2,5</td><td>2,80</td><td>3,3</td><td>3,9</td><td>6,5</td></tr>
<tr><td>9</td><td>300</td><td>1,40</td><td>1,80</td><td>2,2</td><td colspan="2">2,7</td><td>3,00</td><td>3,5</td><td>4,2</td><td>6,0</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td colspan="3"></td></tr>
<tr><td colspan="13">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2">Группы медных сплавов и</td><td colspan="4">Группа сплавов</td><td colspan="3">Гомогенные</td><td colspan="4">Гетерогенные</td></tr>
<tr><td colspan="2" rowspan="2">твердости</td><td colspan="4">Твердость НВ, ГПа</td><td colspan="3">0,59 - 0,88</td><td colspan="2">0,98 - 1,37</td><td colspan="2">1,47 - 2,45</td></tr>
<tr><td colspan="4">Коэффициент</td><td colspan="3">0,55</td><td colspan="2">1,0</td><td colspan="2">1,25</td></tr>
<tr><td colspan="2">Группы алюминиевых</td><td colspan="4">Группа сплавов</td><td colspan="5">Силумин и литейные сплавы</td><td colspan="2">Дюралюминий</td></tr>
<tr><td colspan="2" rowspan="2">сплавов и твердости</td><td colspan="4">Твердость НВ, ГПа</td><td colspan="5">до 0,64</td><td colspan="2">до 0,98</td></tr>
<tr><td colspan="4">Коэффициент</td><td colspan="5">0,75</td><td colspan="2">0,7</td></tr>
</table>


<a id="p101806"></a>*Примечание.* При обработке обратимыми пластинами время по карте принимать с коэффициентом К = 1,15.


<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="10">Неполное штучное время Фрезерование плоскостей, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="13">Горизонтально-расточные станки</td></tr>
<tr><td colspan="10" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="13">Фрезы торцовые с пластинками ВК8</td></tr>
<tr><td colspan="13">Карта 52 Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="15">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td colspan="2">150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="15">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="15">7,5 - 10</td><td rowspan="2">80 --- 100</td><td rowspan="2">48</td><td>3</td><td>1,30</td><td>1,35</td><td>1,40</td><td>1,55</td><td colspan="2">1,60</td><td>1,65</td><td>1,75</td><td>2,15</td><td>2,30</td><td>2,50</td><td>2,75</td><td>3,00</td><td>3,30</td><td>0,30</td><td>600</td><td>380</td><td>3,3</td></tr>
<tr><td>2</td><td>5</td><td>1,30</td><td>1,35</td><td>1,45</td><td>1,60</td><td colspan="2">1,65</td><td>1,75</td><td>1,85</td><td>2,30</td><td>2,45</td><td>2,70</td><td>3,05</td><td>3,30</td><td>3,70</td><td>0,34</td><td>480</td><td>300</td><td>3,8</td></tr>
<tr><td>3</td><td rowspan="2">100 --- 10</td><td rowspan="2">60</td><td>3</td><td>1,30</td><td>1,40</td><td>1,45</td><td>1,60</td><td colspan="2">1,65</td><td>1,75</td><td>1,85</td><td>2,30</td><td>2,45</td><td>2,70</td><td>3,05</td><td>3,30</td><td>3,70</td><td>0,34</td><td>480</td><td>300</td><td>3,3</td></tr>
<tr><td>4</td><td>5</td><td>1,35</td><td>1,40</td><td>1,50</td><td>1,70</td><td colspan="2">1,75</td><td>1,85</td><td>2,00</td><td>2,45</td><td>2,70</td><td>3,00</td><td>3,35</td><td>3,75</td><td>4,25</td><td>0,40</td><td>380</td><td>240</td><td>3,3</td></tr>
<tr><td>5</td><td rowspan="2">125 --- 12</td><td rowspan="2">75</td><td>3</td><td>1,35</td><td>1,40</td><td>1,45</td><td>1,60</td><td colspan="2">1,65</td><td>1,75</td><td>1,85</td><td>2,30</td><td>2,50</td><td>2,70</td><td>3,05</td><td>3,35</td><td>3,75</td><td>0,34</td><td>480</td><td>240</td><td>3,8</td></tr>
<tr><td>6</td><td>5</td><td>1,35</td><td>1,45</td><td>1,50</td><td>1,70</td><td colspan="2">1,75</td><td>1,85</td><td>2,00</td><td>2,50</td><td>2,70</td><td>3,00</td><td>3,40</td><td>3,75</td><td>4,25</td><td>0,40</td><td>380</td><td>190</td><td>4,6</td></tr>
<tr><td>7</td><td rowspan="3">160 --- 16</td><td rowspan="3">112</td><td>3</td><td>1,40</td><td>1,45</td><td>1,55</td><td>1,70</td><td colspan="2">1,80</td><td>1,90</td><td>2,05</td><td>2,50</td><td>2,75</td><td>3,00</td><td>3,40</td><td>3,75</td><td>4,30</td><td>0,40</td><td>380</td><td>150</td><td>4,6</td></tr>
<tr><td>8</td><td>5</td><td>1,45</td><td>1,55</td><td>1,60</td><td>1,80</td><td colspan="2">1,90</td><td>2,05</td><td>2,25</td><td>2,75</td><td>3,00</td><td>3,40</td><td>3,85</td><td>4,30</td><td>4,95</td><td>0,48</td><td>300</td><td>120</td><td>5,5</td></tr>
<tr><td>9</td><td>8</td><td>1,55</td><td>1,70</td><td>1,85</td><td>2,10</td><td colspan="2">2,25</td><td>2,45</td><td>2,75</td><td>3,40</td><td>3,80</td><td>4,40</td><td>5,00</td><td>6,00</td><td>7,00</td><td>0,70</td><td>190</td><td>96</td><td>4,8</td></tr>
<tr><td>10</td><td rowspan="3">200 --- 20</td><td rowspan="3">140</td><td>3</td><td>1,45</td><td>1,55</td><td>1,65</td><td>1,85</td><td colspan="2">1,95</td><td>2,10</td><td>2,25</td><td>2,80</td><td>3,05</td><td>3,40</td><td>3,90</td><td>4,35</td><td>5,00</td><td>0,48</td><td>300</td><td>96</td><td>4,6</td></tr>
<tr><td>11</td><td>5</td><td>1,55</td><td>1,65</td><td>1,75</td><td>2,00</td><td colspan="2">2,10</td><td>2,25</td><td>2,50</td><td>3,05</td><td>3,40</td><td>3,85</td><td>4,45</td><td>5,00</td><td>6,00</td><td>0,55</td><td>240</td><td>75</td><td>5,5</td></tr>
<tr><td>12</td><td>8</td><td>1,75</td><td>1,90</td><td>2,10</td><td>2,40</td><td colspan="2">2,55</td><td>2,85</td><td>3,20</td><td>3,90</td><td>4,45</td><td>5,00</td><td>6,00</td><td>7,00</td><td>8,00</td><td>0,85</td><td>150</td><td>60</td><td>5,0</td></tr>
<tr><td>13</td><td rowspan="3">250 --- 24</td><td rowspan="3">190</td><td>3</td><td>1,55</td><td>1,60</td><td>1,70</td><td>1,90</td><td colspan="2">2,00</td><td>2,15</td><td>2,30</td><td>2,85</td><td>3,10</td><td>3,50</td><td>3,95</td><td>4,40</td><td>5,00</td><td>0,48</td><td>300</td><td>75</td><td>6,0</td></tr>
<tr><td>14</td><td>5</td><td>1,60</td><td>1,70</td><td>1,85</td><td>2,05</td><td colspan="2">2,15</td><td>2,35</td><td>2,60</td><td>3,15</td><td>3,50</td><td>3,95</td><td>4,50</td><td>5,00</td><td>6,00</td><td>0,55</td><td>240</td><td>60</td><td>6,0</td></tr>
<tr><td>15</td><td>8</td><td>2,00</td><td>2,25</td><td>2,45</td><td>2,80</td><td colspan="2">3,05</td><td>3,35</td><td>3,85</td><td>4,60</td><td>5,50</td><td>6,00</td><td>7,50</td><td>8,50</td><td>10,00</td><td>1,00</td><td>120</td><td>48</td><td>5,5</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="5%"><col width="2%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="10">Неполное штучное время Фрезерование плоскостей, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="16">Горизонтально-расточные станки</td></tr>
<tr><td colspan="10" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="16">Фрезы торцовые с пластинками ВК8</td></tr>
<tr><td colspan="9">Карта 52</td><td colspan="7">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="18">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td colspan="2">150</td><td colspan="2">200</td><td>250</td><td>300</td><td>400</td><td colspan="2">500</td><td>600</td><td>750</td><td>950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="18">Время на проход, мин.</td></tr>
<tr><td>16</td><td rowspan="3">7,5 - 10</td><td rowspan="3">315 --- 24</td><td rowspan="3">240</td><td>3</td><td>1,65</td><td>1,75</td><td>1,90</td><td>2,1</td><td colspan="2">2,25</td><td colspan="2">2,40</td><td>2,65</td><td>3,2</td><td>3,55</td><td colspan="2">4,0</td><td>4,55</td><td>5,0</td><td>6,0</td><td colspan="2">0,55</td><td>240</td><td>60</td><td>6,6</td></tr>
<tr><td>17</td><td>5</td><td>1,75</td><td>1,90</td><td>2,05</td><td>2,3</td><td colspan="2">2,45</td><td colspan="2">2,70</td><td>2,95</td><td>3,6</td><td>4,00</td><td colspan="2">4,6</td><td>5,50</td><td>6,0</td><td>7,0</td><td colspan="2">0,70</td><td>190</td><td>48</td><td>6,6</td></tr>
<tr><td>18</td><td>8</td><td>2,35</td><td>2,65</td><td>3,00</td><td>3,3</td><td colspan="2">3,60</td><td colspan="2">4,05</td><td>4,60</td><td>5,5</td><td>6,50</td><td colspan="2">7,5</td><td>9,00</td><td>10,0</td><td>12,0</td><td colspan="2">1,25</td><td>96</td><td>38</td><td>6,6</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="3"></td></tr>
<tr><td colspan="26">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="10">Твердости чугуна и Твердость НВ, ГПа</td><td colspan="7">до 2,15</td><td colspan="9">свыше 2,15</td></tr>
<tr><td colspan="10">обработки Продолжительность обработки, мин.</td><td colspan="7">-</td><td colspan="5">до 10</td><td colspan="4">свыше 10</td></tr>
<tr><td colspan="10" rowspan="3">Коэффициент</td><td colspan="7"></td><td colspan="5" rowspan="3">1,1</td><td colspan="4" rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td colspan="5"></td></tr>
<tr><td colspan="7"></td></tr>
<tr><td colspan="10">Состояния Состояние обрабатываемой обрабатываемой поверхности</td><td colspan="7">без корки</td><td colspan="9">по корке</td></tr>
<tr><td colspan="10" rowspan="3">Коэффициент</td><td colspan="7"></td><td colspan="9" rowspan="3">1,2</td></tr>
<tr><td colspan="2">1,0</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="4%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="11">Неполное штучное время Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="13">Горизонтально-расточные станки</td></tr>
<tr><td colspan="11" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="13">Фрезы торцовые с пластинками ВК8</td></tr>
<tr><td colspan="13">Карта 53</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="16">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N д, кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td colspan="2">200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="16">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="14">7,5 - 10</td><td rowspan="2">80 -- 10</td><td rowspan="2">40</td><td>3</td><td>2,10</td><td>2,10</td><td>2,15</td><td>2,45</td><td>2,50</td><td colspan="2">2,55</td><td>2,65</td><td>3,40</td><td>3,50</td><td>3,70</td><td>4,20</td><td>4,50</td><td>4,75</td><td colspan="2">0,30</td><td>600</td><td>480</td><td>3,5</td></tr>
<tr><td>2</td><td>5</td><td>2,15</td><td>2,20</td><td>2,25</td><td>2,50</td><td>2,60</td><td colspan="2">2,65</td><td>2,80</td><td>3,55</td><td>3,70</td><td>3,95</td><td>4,50</td><td>4,80</td><td>5,00</td><td colspan="2">0,34</td><td>480</td><td>380</td><td>4,2</td></tr>
<tr><td>3</td><td rowspan="2">100 --- 10</td><td rowspan="2">60</td><td>3</td><td>2,20</td><td>2,25</td><td>2,30</td><td>2,55</td><td>2,60</td><td colspan="2">2,70</td><td>2,80</td><td>3,60</td><td>3,75</td><td>4,00</td><td>4,55</td><td>4,85</td><td>5,00</td><td colspan="2">0,34</td><td>480</td><td>380</td><td>3,5</td></tr>
<tr><td>4</td><td>5</td><td>2,25</td><td>2,35</td><td>2,40</td><td>2,70</td><td>2,75</td><td colspan="2">2,85</td><td>3,00</td><td>3,80</td><td>4,05</td><td>4,30</td><td>4,95</td><td>5,50</td><td>6,00</td><td colspan="2">0,40</td><td>380</td><td>300</td><td>3,8</td></tr>
<tr><td>5</td><td rowspan="2">125 --- 12</td><td rowspan="2">75</td><td>3</td><td>2,35</td><td>2,40</td><td>2,45</td><td>2,75</td><td>2,85</td><td colspan="2">2,95</td><td>3,10</td><td>3,90</td><td>4,10</td><td>4,40</td><td>5,00</td><td>5,50</td><td>6,00</td><td colspan="2">0,40</td><td>380</td><td>300</td><td>3,3</td></tr>
<tr><td>6</td><td>5</td><td>2,45</td><td>2,55</td><td>2,65</td><td>2,95</td><td>3,05</td><td colspan="2">3,20</td><td>3,35</td><td>4,20</td><td>4,45</td><td>4,85</td><td>5,50</td><td>6,00</td><td>6,50</td><td colspan="2">0,48</td><td>300</td><td>240</td><td>4,5</td></tr>
<tr><td>7</td><td rowspan="2">160 --- 16</td><td rowspan="2">112</td><td>3</td><td>2,45</td><td>2,50</td><td>2,60</td><td>2,85</td><td>2,95</td><td colspan="2">3,05</td><td>3,20</td><td>4,00</td><td>4,20</td><td>4,50</td><td>5,00</td><td>5,50</td><td>6,00</td><td colspan="2">0,40</td><td>380</td><td>240</td><td>4,8</td></tr>
<tr><td>8</td><td>5</td><td>2,60</td><td>2,65</td><td>2,75</td><td>3,10</td><td>3,15</td><td colspan="2">3,30</td><td>3,50</td><td>4,35</td><td>4,60</td><td>4,95</td><td>5,50</td><td>6,00</td><td>7,00</td><td colspan="2">0,48</td><td>300</td><td>190</td><td>6,6</td></tr>
<tr><td>9</td><td rowspan="2">200 --- 20</td><td rowspan="2">140</td><td>3</td><td>2,55</td><td>2,65</td><td>2,70</td><td>3,00</td><td>3,05</td><td colspan="2">3,20</td><td>3,30</td><td>4,10</td><td>4,35</td><td>4,65</td><td>5,50</td><td>5,50</td><td>6,00</td><td colspan="2">0,40</td><td>380</td><td>190</td><td>6,0</td></tr>
<tr><td>10</td><td>5</td><td>2,75</td><td>2,85</td><td>2,90</td><td>3,25</td><td>3,35</td><td colspan="2">3,45</td><td>3,65</td><td>4,50</td><td>4,75</td><td>5,00</td><td>6,00</td><td>6,50</td><td>7,00</td><td colspan="2">0,48</td><td>300</td><td>150</td><td>7,5</td></tr>
<tr><td>11</td><td rowspan="2">250 --- 24</td><td rowspan="2">190</td><td>3</td><td>2,90</td><td>3,00</td><td>3,10</td><td>3,40</td><td>3,30</td><td colspan="2">3,65</td><td>3,85</td><td>4,65</td><td>4,95</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,00</td><td colspan="2">0,48</td><td>300</td><td>150</td><td>6,6</td></tr>
<tr><td>12</td><td>5</td><td>3,55</td><td>3,70</td><td>3,80</td><td>4,20</td><td>4,35</td><td colspan="2">4,55</td><td>4,85</td><td>6,00</td><td>6,00</td><td>7,00</td><td>7,50</td><td>8,50</td><td>9,50</td><td colspan="2">0,70</td><td>190</td><td>120</td><td>7,4</td></tr>
<tr><td>13</td><td rowspan="2">315 --- 24</td><td rowspan="2">240</td><td>3</td><td>3,50</td><td>3,60</td><td>3,70</td><td>4,05</td><td>4,15</td><td colspan="2">4,35</td><td>4,55</td><td>5,50</td><td>6,00</td><td>6,50</td><td>7,00</td><td>7,50</td><td>8,50</td><td colspan="2">0,55</td><td>240</td><td>120</td><td>6,6</td></tr>
<tr><td>14</td><td>5</td><td>4,45</td><td>4,65</td><td>4,80</td><td>5,00</td><td>5,50</td><td colspan="2">5,50</td><td>6,00</td><td>7,00</td><td>7,50</td><td>8,50</td><td>9,50</td><td>10,50</td><td>11,50</td><td colspan="2">0,85</td><td>150</td><td>96</td><td>7,2</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="3"></td></tr>
<tr><td colspan="24">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Твердости чугуна и продолжительности</td><td colspan="8">Твердость НВ, ГПа</td><td colspan="5">до 2,15</td><td colspan="7">свыше 2,15</td></tr>
<tr><td colspan="4" rowspan="4">обработки</td><td colspan="8">Продолжительность обработки, мин.</td><td colspan="5">-</td><td colspan="3">до 10</td><td colspan="4">свыше 10</td></tr>
<tr><td colspan="8" rowspan="3">Коэффициент</td><td colspan="5"></td><td colspan="3" rowspan="3">1,1</td><td colspan="4" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="4%"><col width="5%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="23">Неполное штучное время Горизонтально-расточные станки</td></tr>
<tr><td colspan="23">Чугун серый, НВ = 1,76 - 2,15 ГПа Фрезы торцовые с пластинками ВК6</td></tr>
<tr><td colspan="23">Карта 54</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="15">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="15">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="7">7,5 - 10</td><td>80 -- 10</td><td>48</td><td rowspan="7">1</td><td>2,80</td><td>2,85</td><td>2,85</td><td>3,35</td><td>3,40</td><td>3,45</td><td>3,50</td><td>4,35</td><td>4,45</td><td>4,60</td><td>5,0</td><td>5,5</td><td>5,5</td><td colspan="2">0,37</td><td>750</td><td>750</td><td rowspan="7">Не свыше 2,0</td></tr>
<tr><td>2</td><td>100 --- 10</td><td>60</td><td>2,90</td><td>2,90</td><td>2,95</td><td>3,45</td><td>3,50</td><td>3,55</td><td>3,65</td><td>4,50</td><td>4,65</td><td>4,85</td><td>5,5</td><td>5,5</td><td>6,0</td><td colspan="2">0,40</td><td>600</td><td>600</td></tr>
<tr><td>3</td><td>125 --- 12</td><td>75</td><td>3,00</td><td>3,05</td><td>3,10</td><td>3,60</td><td>3,65</td><td>3,75</td><td>3,85</td><td>4,75</td><td>4,90</td><td>5,00</td><td>6,0</td><td>6,0</td><td>6,5</td><td colspan="2">0,45</td><td>480</td><td>480</td></tr>
<tr><td>4</td><td>160 --- 16</td><td>112</td><td>3,10</td><td>3,15</td><td>3,20</td><td>3,70</td><td>3,75</td><td>3,85</td><td>3,95</td><td>4,80</td><td>5,00</td><td>5,00</td><td>6,0</td><td>6,0</td><td>6,5</td><td colspan="2">0,45</td><td>480</td><td>380</td></tr>
<tr><td>5</td><td>200 --- 20</td><td>140</td><td>3,20</td><td>3,25</td><td>3,30</td><td>3,80</td><td>3,85</td><td>3,95</td><td>4,05</td><td>4,95</td><td>5,00</td><td>5,50</td><td>6,0</td><td>6,5</td><td>6,5</td><td colspan="2">0,45</td><td>480</td><td>300</td></tr>
<tr><td>6</td><td>250 --- 24</td><td>190</td><td>3,30</td><td>3,35</td><td>3,40</td><td>3,90</td><td>3,95</td><td>4,05</td><td>4,15</td><td>5,00</td><td>5,00</td><td>5,50</td><td>6,0</td><td>6,5</td><td>7,0</td><td colspan="2">0,45</td><td>480</td><td>240</td></tr>
<tr><td>7</td><td>315 --- 24</td><td>240</td><td>3,65</td><td>3,75</td><td>3,80</td><td>4,30</td><td>4,40</td><td>4,50</td><td>4,65</td><td>5,50</td><td>6,00</td><td>6,00</td><td>7,0</td><td>7,0</td><td>7,5</td><td colspan="2">0,51</td><td>380</td><td>190</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="3"></td></tr>
<tr><td colspan="23">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Твердости чугуна и продолжительности</td><td colspan="19">Твердость НВ, ГПа до 2,15 свыше 2,15</td></tr>
<tr><td colspan="4" rowspan="4">обработки</td><td colspan="15">Продолжительность обработки, мин. - до 10</td><td colspan="4">свыше 10</td></tr>
<tr><td colspan="15"></td><td colspan="4" rowspan="3">1,25</td></tr>
<tr><td colspan="7">Коэффициент</td><td colspan="8">1,0 1,1</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="2%"><col width="3%"><col width="2%"><col width="3%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="3%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="5%"><col width="2%"><col width="3%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="29">Неполное штучное время Горизонтально-расточные станки Фрезерование плоскостей, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="29">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Фрезы торцовые из стали Р6М5 в</td></tr>
<tr><td colspan="29">Единичное и мелкосерийное производство Карта 55</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="20">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td colspan="2">100</td><td colspan="2">125</td><td colspan="2">150</td><td>200</td><td>250</td><td>300</td><td>400</td><td colspan="2">500</td><td colspan="2">600</td><td>750</td><td>950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td colspan="2" rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="20">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="12">7,5 - 10</td><td rowspan="2">80 -- 10</td><td rowspan="2">48</td><td>3</td><td>1,65</td><td>1,90</td><td colspan="2">2,10</td><td colspan="2">2,45</td><td colspan="2">2,70</td><td>3,05</td><td>3,50</td><td>4,25</td><td>4,95</td><td colspan="2">6,0</td><td colspan="2">7,0</td><td>8,5</td><td>10,0</td><td colspan="2">1,00</td><td colspan="2">120</td><td>75</td><td rowspan="12">Не свыше 3,6</td></tr>
<tr><td>2</td><td>5</td><td>1,75</td><td>2,05</td><td colspan="2">2,35</td><td colspan="2">2,75</td><td colspan="2">3,00</td><td>3,45</td><td>4,00</td><td>4,90</td><td>6,00</td><td colspan="2">7,0</td><td colspan="2">8,5</td><td>10,0</td><td>12,0</td><td colspan="2">1,25</td><td colspan="2">96</td><td>75</td></tr>
<tr><td>3</td><td rowspan="2">100 --- 10</td><td rowspan="2">60</td><td>3</td><td>1,80</td><td>2,10</td><td colspan="2">2,40</td><td colspan="2">2,75</td><td colspan="2">3,05</td><td>3,50</td><td>4,05</td><td>4,95</td><td>6,00</td><td colspan="2">7,0</td><td colspan="2">8,5</td><td>10,0</td><td>12,0</td><td colspan="2">1,25</td><td colspan="2">96</td><td>60</td></tr>
<tr><td>4</td><td>5</td><td>1,95</td><td>2,35</td><td colspan="2">2,70</td><td colspan="2">3,15</td><td colspan="2">3,55</td><td>4,10</td><td>4,80</td><td>6,00</td><td>7,00</td><td colspan="2">8,5</td><td colspan="2">10,0</td><td>12,0</td><td>14,5</td><td colspan="2">5,60</td><td colspan="2">75</td><td>60</td></tr>
<tr><td>5</td><td rowspan="2">125 --- 14</td><td rowspan="2">75</td><td>3</td><td>1,85</td><td>2,10</td><td colspan="2">2,40</td><td colspan="2">2,80</td><td colspan="2">3,10</td><td>3,50</td><td>4,10</td><td>5,00</td><td>6,00</td><td colspan="2">7,0</td><td colspan="2">8,5</td><td>10,0</td><td>12,0</td><td colspan="2">1,25</td><td colspan="2">96</td><td>48</td></tr>
<tr><td>6</td><td>5</td><td>2,00</td><td>2,40</td><td colspan="2">2,75</td><td colspan="2">3,20</td><td colspan="2">3,60</td><td>4,15</td><td>4,85</td><td>6,00</td><td>7,00</td><td colspan="2">8,5</td><td colspan="2">10,5</td><td>12,0</td><td>14,5</td><td colspan="2">1,60</td><td colspan="2">75</td><td>48</td></tr>
<tr><td>7</td><td rowspan="3">160 --- 16</td><td rowspan="3">112</td><td>3</td><td>1,95</td><td>2,25</td><td colspan="2">2,55</td><td colspan="2">2,95</td><td colspan="2">3,20</td><td>3,65</td><td>4,20</td><td>5,50</td><td>6,00</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td>10,0</td><td>12,0</td><td colspan="2">1,25</td><td colspan="2">96</td><td>38</td></tr>
<tr><td>8</td><td>5</td><td>2,15</td><td>2,55</td><td colspan="2">2,90</td><td colspan="2">3,40</td><td colspan="2">3,75</td><td>4,30</td><td>5,50</td><td>6,50</td><td>7,50</td><td colspan="2">9,0</td><td colspan="2">10,5</td><td>12,5</td><td>15,0</td><td colspan="2">1,60</td><td colspan="2">75</td><td>38</td></tr>
<tr><td>9</td><td>8</td><td>2,40</td><td>2,85</td><td colspan="2">3,30</td><td colspan="2">3,90</td><td colspan="2">4,35</td><td>5,50</td><td>6,00</td><td>7,50</td><td>9,00</td><td colspan="2">10,5</td><td colspan="2">12,5</td><td>15,0</td><td>18,0</td><td colspan="2">1,95</td><td colspan="2">60</td><td>38</td></tr>
<tr><td>10</td><td rowspan="3">200 --- 20</td><td rowspan="3">140</td><td>3</td><td>2,05</td><td>2,35</td><td colspan="2">2,60</td><td colspan="2">3,00</td><td colspan="2">3,30</td><td>3,75</td><td>4,30</td><td>5,50</td><td>6,50</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td>10,0</td><td>12,0</td><td colspan="2">1,25</td><td colspan="2">96</td><td>30</td></tr>
<tr><td>11</td><td>5</td><td>2,25</td><td>2,65</td><td colspan="2">3,00</td><td colspan="2">3,50</td><td colspan="2">3,85</td><td>4,40</td><td>5,50</td><td>6,50</td><td>7,50</td><td colspan="2">9,0</td><td colspan="2">10,5</td><td>11,5</td><td>15,0</td><td colspan="2">1,60</td><td colspan="2">75</td><td>30</td></tr>
<tr><td>12</td><td>8</td><td>2,55</td><td>3,00</td><td colspan="2">3,45</td><td colspan="2">4,00</td><td colspan="2">4,45</td><td>5,50</td><td>6,50</td><td>7,50</td><td>9,00</td><td colspan="2">11,0</td><td colspan="2">12,5</td><td>15,0</td><td>18,0</td><td colspan="2">1,95</td><td colspan="2">60</td><td>30</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td colspan="2">г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td colspan="2">л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="4"></td></tr>
<tr><td colspan="29">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">Группы обрабатываемой стали, предела</td><td colspan="5">Группа стали</td><td colspan="10">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="11">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3" rowspan="5">прочности и продолжительности обработки</td><td colspan="5">Предел прочности сигма , в ГПа</td><td colspan="4">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="3">свыше 0,74</td><td colspan="8">до 0,59 0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="5">Продолжительность обработки, мин.</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td><td colspan="3">-</td><td colspan="3">до 10 свыше 10</td><td colspan="2">до 10</td><td colspan="4">свыше до 10 10</td><td colspan="2">свыше 10</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,9</td><td colspan="2" rowspan="3">0,8</td><td colspan="3" rowspan="3">1,0</td><td colspan="3" rowspan="3">1,1 1,25</td><td colspan="2"></td><td colspan="4" rowspan="3">1,1 1,1</td><td colspan="2" rowspan="3">1,2</td><td colspan="3" rowspan="3">1,2 1,35</td></tr>
<tr><td colspan="2">1,0</td></tr>
<tr><td colspan="2"></td></tr>
<tr><td colspan="3" rowspan="4">Состояния обрабатываемой поверхности</td><td colspan="5">Состояние обрабатываемой поверхности</td><td colspan="10">без корки и удара</td><td colspan="11">по корке и на удар</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="10"></td><td colspan="11" rowspan="3">1,2</td></tr>
<tr><td colspan="2">1,0</td><td colspan="8"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="2%"><col width="3%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="3%"><col width="2%"><col width="3%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="30">Неполное штучное время Горизонтально-расточные станки Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 квалитет</td></tr>
<tr><td colspan="30">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Фрезы торцовые из стали Р6М5 в</td></tr>
<tr><td colspan="30">Единичное и мелкосерийное производство Карта 56</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="21">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td colspan="2">100</td><td colspan="2">125</td><td>150</td><td>200</td><td colspan="2">250</td><td colspan="2">300</td><td colspan="2">400</td><td>500</td><td>600</td><td>750</td><td colspan="2">950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td colspan="2" rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="21">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="10">7,5 - 10</td><td rowspan="2">80 -- 10</td><td rowspan="2">48</td><td>3</td><td>2,75</td><td>2,95</td><td colspan="2">3,10</td><td colspan="2">3,50</td><td>3,70</td><td>3,95</td><td colspan="2">4,35</td><td colspan="2">5,5</td><td colspan="2">6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10,0</td><td colspan="2">0,85</td><td colspan="2">150</td><td>120</td><td rowspan="10">Не свыше 2,5</td></tr>
<tr><td>2</td><td>5</td><td>2,95</td><td>3,20</td><td colspan="2">3,40</td><td colspan="2">3,85</td><td>4,10</td><td>4,45</td><td colspan="2">4,90</td><td colspan="2">6,0</td><td colspan="2">7,0</td><td>8,0</td><td>9,0</td><td>10,0</td><td colspan="2">12,0</td><td colspan="2">1,00</td><td colspan="2">120</td><td>120</td></tr>
<tr><td>3</td><td rowspan="2">100 --- 10</td><td rowspan="2">60</td><td>3</td><td>3,15</td><td>3,35</td><td colspan="2">3,60</td><td colspan="2">4,05</td><td>4,25</td><td>4,60</td><td colspan="2">5,50</td><td colspan="2">6,5</td><td colspan="2">7,0</td><td>8,5</td><td>9,0</td><td>10,5</td><td colspan="2">12,0</td><td colspan="2">1,00</td><td colspan="2">120</td><td>96</td></tr>
<tr><td>4</td><td>5</td><td>3,45</td><td>3,75</td><td colspan="2">4,05</td><td colspan="2">4,55</td><td>4,80</td><td>5,50</td><td colspan="2">6,00</td><td colspan="2">7,5</td><td colspan="2">8,0</td><td>9,5</td><td>10,5</td><td>12,0</td><td colspan="2">14,0</td><td colspan="2">1,25</td><td colspan="2">96</td><td>96</td></tr>
<tr><td>5</td><td rowspan="2">125 --- 14</td><td rowspan="2">75</td><td>3</td><td>3,35</td><td>3,60</td><td colspan="2">3,85</td><td colspan="2">4,25</td><td>4,50</td><td>4,85</td><td colspan="2">5,50</td><td colspan="2">6,5</td><td colspan="2">7,5</td><td>8,0</td><td>9,5</td><td>10,5</td><td colspan="2">12,0</td><td colspan="2">1,00</td><td colspan="2">120</td><td>60</td></tr>
<tr><td>6</td><td>5</td><td>3,75</td><td>4,05</td><td colspan="2">4,30</td><td colspan="2">4,80</td><td>5,50</td><td>6,00</td><td colspan="2">6,50</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td>9,5</td><td>11,0</td><td>12,5</td><td colspan="2">14,5</td><td colspan="2">1,25</td><td colspan="2">96</td><td>60</td></tr>
<tr><td>7</td><td rowspan="2">160 --- 16</td><td rowspan="2">112</td><td>3</td><td>3,70</td><td>3,95</td><td colspan="2">4,15</td><td colspan="2">4,60</td><td>4,85</td><td>5,50</td><td colspan="2">6,00</td><td colspan="2">7,0</td><td colspan="2">9,0</td><td>8,5</td><td>10,0</td><td>11,0</td><td colspan="2">12,5</td><td colspan="2">1,00</td><td colspan="2">120</td><td>48</td></tr>
<tr><td>8</td><td>5</td><td>4,15</td><td>4,45</td><td colspan="2">4,75</td><td colspan="2">5,50</td><td>5,50</td><td>6,00</td><td colspan="2">7,00</td><td colspan="2">8,0</td><td colspan="2">9,0</td><td>10,0</td><td>11,5</td><td>13,0</td><td colspan="2">15,0</td><td colspan="2">1,25</td><td colspan="2">96</td><td>48</td></tr>
<tr><td>9</td><td rowspan="2">200 --- 20</td><td rowspan="2">140</td><td>3</td><td>4,60</td><td>4,90</td><td colspan="2">5,50</td><td colspan="2">6,00</td><td>6,00</td><td>6,50</td><td colspan="2">7,00</td><td colspan="2">8,0</td><td colspan="2">9,5</td><td>10,5</td><td>11,0</td><td>13,5</td><td colspan="2">15,5</td><td colspan="2">1,25</td><td colspan="2">96</td><td>38</td></tr>
<tr><td>10</td><td>5</td><td>5,50</td><td>6,00</td><td colspan="2">6,50</td><td colspan="2">7,00</td><td>7,50</td><td>8,00</td><td colspan="2">8,50</td><td colspan="2">10,0</td><td colspan="2">11,0</td><td>12,5</td><td>14,5</td><td>16,0</td><td colspan="2">18,5</td><td colspan="2">1,60</td><td colspan="2">75</td><td>38</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td colspan="2">г</td><td>д</td><td>е</td><td colspan="2">ж</td><td colspan="2">з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td colspan="2">н</td><td colspan="2">о</td><td colspan="4"></td></tr>
<tr><td colspan="30">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">Группы обрабатываемой стали, предела</td><td colspan="5">Группа стали</td><td colspan="22">Углеродистые, хромистые, никелевые, Марганцовистые, хромомарганцовистые, хромоникелевые хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3" rowspan="5">прочности и продолжительности обработки</td><td colspan="5">Предел прочности сигма , в ГПа</td><td colspan="8">до 0,59 0,59 - 0,74</td><td colspan="7">свыше 0,74 до 0,59</td><td colspan="4">0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="5">Продолжительность обработки, мин.</td><td colspan="2">до 10</td><td colspan="3">свыше до 10 10</td><td colspan="3">свыше 10</td><td colspan="2">до 10</td><td colspan="5">свыше до 10 свыше 10 10</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,9</td><td colspan="6"></td><td colspan="2" rowspan="3">1,1</td><td colspan="5"></td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td colspan="3" rowspan="3">1,2 1,35</td></tr>
<tr><td colspan="4">0,8 1,0</td><td colspan="2"></td><td colspan="2">1,25</td><td colspan="3">1,0 1,1</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"><col width="4%"><col width="4%"><col width="2%"><col width="3%"><col width="3%"><col width="2%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="3%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="4%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="13">Неполное штучное время Фрезерование плоскостей, Ra 2,5, 1Т9 квалитет</td><td colspan="16">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="16">Фрезы торцовые из стали Р6М5</td></tr>
<tr><td colspan="13">Единичное и мелкосерийное производство</td><td colspan="16">Карта 57</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="20">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td colspan="2">125</td><td colspan="2">150</td><td colspan="2">200</td><td>250</td><td>300</td><td>400</td><td colspan="2">500</td><td colspan="2">600</td><td>750</td><td>950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td colspan="2" rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="20">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="5">7,5 - 10</td><td>80 -- 10</td><td>48</td><td rowspan="5">1</td><td>4,75</td><td>5,0</td><td>5,5</td><td colspan="2">6,5</td><td colspan="2">7,0</td><td colspan="2">7,5</td><td>8,5</td><td>9,0</td><td>11,5</td><td colspan="2">13,5</td><td colspan="2">15,5</td><td>18,0</td><td>21,0</td><td colspan="2">2,05</td><td colspan="2">60</td><td>150</td><td rowspan="5">Не свыше 1,0</td></tr>
<tr><td>2</td><td>100 --- 10</td><td>60</td><td>6,00</td><td>6,5</td><td>7,0</td><td colspan="2">8,0</td><td colspan="2">8,5</td><td colspan="2">9,5</td><td>10,5</td><td>11,0</td><td>14,0</td><td colspan="2">16,5</td><td colspan="2">18,5</td><td>22,0</td><td>26,0</td><td colspan="2">2,50</td><td colspan="2">48</td><td>120</td></tr>
<tr><td>3</td><td>125 --- 14</td><td>75</td><td>7,5</td><td>8,0</td><td>9,0</td><td colspan="2">10,0</td><td colspan="2">10,5</td><td colspan="2">11,5</td><td>13,0</td><td>14,0</td><td>17,5</td><td colspan="2">20,5</td><td colspan="2">23,5</td><td>27,5</td><td>32,5</td><td colspan="2">3,10</td><td colspan="2">38</td><td>96</td></tr>
<tr><td>4</td><td>160 --- 16</td><td>112</td><td>10,00</td><td>11,0</td><td>11,5</td><td colspan="2">13,0</td><td colspan="2">14,0</td><td colspan="2">15,5</td><td>16,5</td><td>18,0</td><td>22,5</td><td colspan="2">26,0</td><td colspan="2">30,0</td><td>35,0</td><td>41,4</td><td colspan="2">3,90</td><td colspan="2">30</td><td>75</td></tr>
<tr><td>5</td><td>200 --- 20</td><td>140</td><td>13,50</td><td>14,5</td><td>16,0</td><td colspan="2">17,5</td><td colspan="2">18,5</td><td colspan="2">20,5</td><td>22,5</td><td>23,5</td><td>29,0</td><td colspan="2">33,5</td><td colspan="2">38,0</td><td>44,5</td><td>52,0</td><td colspan="2">4,80</td><td colspan="2">24</td><td>60</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td colspan="2">д</td><td colspan="2">е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td colspan="2">л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="4"></td></tr>
<tr><td colspan="29">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">Группы обрабатываемой стали, предела</td><td colspan="15">Группа стали Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="11">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3" rowspan="5">прочности и продолжительности обработки</td><td colspan="8">Предел прочности сигма , до 0,59 в ГПа</td><td colspan="4">0,59 - 0,74</td><td colspan="3">свыше 0,74</td><td colspan="4">до 0,59</td><td colspan="4">0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="6">Продолжительность до 10 обработки, мин.</td><td colspan="2">свыше 10</td><td colspan="4">-</td><td colspan="3">до 10 свыше 10</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент 0,9</td><td colspan="2" rowspan="3">0,8</td><td colspan="4" rowspan="3">1,0</td><td colspan="3" rowspan="3">1,1 1,25</td><td colspan="2"></td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td colspan="3" rowspan="3">1,2 1,35</td></tr>
<tr><td colspan="2">1,0</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="23">Неполное штучное время Горизонтально-расточные станки</td></tr>
<tr><td colspan="23">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Фрезы торцовые с пластинками Т5К10</td></tr>
<tr><td colspan="16">Единичное и мелкосерийное производство Карта 58</td><td colspan="7">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="15">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td colspan="2">600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="15">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="18">7,5 - 10</td><td rowspan="2">80 -- 8</td><td rowspan="2">48</td><td>3</td><td>1,30</td><td>1,35</td><td>1,45</td><td>1,60</td><td>1,65</td><td>1,75</td><td>1,85</td><td>2,30</td><td>2,45</td><td>2,70</td><td colspan="2">3,05</td><td>3,30</td><td>3,70</td><td>0,34</td><td>480</td><td>480</td><td>4,0</td></tr>
<tr><td>2</td><td>5</td><td>1,35</td><td>1,40</td><td>1,50</td><td>1,65</td><td>1,75</td><td>1,85</td><td>2,00</td><td>2,65</td><td>2,70</td><td>2,95</td><td colspan="2">3,35</td><td>3,75</td><td>4,25</td><td>0,40</td><td>380</td><td>380</td><td>5,0</td></tr>
<tr><td>3</td><td rowspan="2">100 --- 8</td><td rowspan="2">60</td><td>3</td><td>1,35</td><td>1,40</td><td>1,50</td><td>1,70</td><td>1,75</td><td>1,85</td><td>2,00</td><td>2,45</td><td>2,70</td><td>3,00</td><td colspan="2">3,35</td><td>3,75</td><td>4,25</td><td>0,40</td><td>380</td><td>380</td><td>3,6</td></tr>
<tr><td>4</td><td>5</td><td>1,40</td><td>1,50</td><td>1,55</td><td>1,75</td><td>1,85</td><td>2,00</td><td>2,20</td><td>2,70</td><td>3,00</td><td>3,35</td><td colspan="2">3,80</td><td>4,25</td><td>4,90</td><td>0,48</td><td>300</td><td>300</td><td>5,4</td></tr>
<tr><td>5</td><td rowspan="2">125 --- 8</td><td rowspan="2">75</td><td>3</td><td>1,40</td><td>1,50</td><td>1,60</td><td>1,80</td><td>1,85</td><td>2,00</td><td>2,20</td><td>2,70</td><td>3,00</td><td>3,35</td><td colspan="2">3,80</td><td>4,25</td><td>4,90</td><td>0,48</td><td>300</td><td>300</td><td>4,0</td></tr>
<tr><td>6</td><td>5</td><td>1,45</td><td>1,55</td><td>1,70</td><td>1,90</td><td>2,00</td><td>2,20</td><td>2,40</td><td>2,95</td><td>3,30</td><td>3,75</td><td colspan="2">4,35</td><td>4,90</td><td>5,50</td><td>0,55</td><td>240</td><td>240</td><td>5,5</td></tr>
<tr><td>7</td><td rowspan="3">160 --- 10</td><td rowspan="3">112</td><td>3</td><td>1,50</td><td>1,60</td><td>1,70</td><td>1,95</td><td>2,05</td><td>2,25</td><td>2,45</td><td>3,00</td><td>3,35</td><td>3,80</td><td colspan="2">4,40</td><td>4,95</td><td>5,50</td><td>0,55</td><td>240</td><td>190</td><td>5,0</td></tr>
<tr><td>8</td><td>5</td><td>1,65</td><td>1,85</td><td>2,05</td><td>2,35</td><td>2,50</td><td>2,80</td><td>3,15</td><td>3,85</td><td>4,40</td><td>5,00</td><td colspan="2">6,00</td><td>7,00</td><td>8,00</td><td>0,85</td><td>150</td><td>120</td><td>5,5</td></tr>
<tr><td>9</td><td>8</td><td>1,95</td><td>2,20</td><td>2,50</td><td>2,90</td><td>3,20</td><td>3,60</td><td>4,20</td><td>5,00</td><td>6,00</td><td>7,00</td><td colspan="2">8,50</td><td>10,00</td><td>11,50</td><td>1,25</td><td>96</td><td>75</td><td>6,6</td></tr>
<tr><td>10</td><td rowspan="3">200 --- 12</td><td rowspan="3">140</td><td>3</td><td>1,60</td><td>1,75</td><td>1,90</td><td>2,15</td><td>2,30</td><td>2,50</td><td>2,80</td><td>3,65</td><td>3,85</td><td>4,45</td><td colspan="2">5,00</td><td>6,00</td><td>7,00</td><td>0,70</td><td>190</td><td>120</td><td>5,0</td></tr>
<tr><td>11</td><td>5</td><td>1,85</td><td>2,10</td><td>2,30</td><td>2,65</td><td>2,90</td><td>3,25</td><td>3,70</td><td>4,50</td><td>5,00</td><td>6,00</td><td colspan="2">7,00</td><td>8,50</td><td>10,00</td><td>1,00</td><td>120</td><td>75</td><td>6,6</td></tr>
<tr><td>12</td><td>8</td><td>2,00</td><td>2,30</td><td>2,60</td><td>3,00</td><td>3,25</td><td>3,70</td><td>4,30</td><td>5,00</td><td>6,00</td><td>7,00</td><td colspan="2">8,50</td><td>10,00</td><td>12,00</td><td>1,25</td><td>96</td><td>60</td><td>7,5</td></tr>
<tr><td>13</td><td rowspan="3">250 --- 14</td><td rowspan="3">190</td><td>3</td><td>1,85</td><td>2,00</td><td>2,20</td><td>2,50</td><td>2,70</td><td>2,95</td><td>3,35</td><td>4,00</td><td>4,60</td><td>5,50</td><td colspan="2">6,00</td><td>7,00</td><td>8,50</td><td>0,85</td><td>150</td><td>75</td><td>6,9</td></tr>
<tr><td>14</td><td>5</td><td>2,20</td><td>2,50</td><td>2,75</td><td>3,15</td><td>3,45</td><td>3,90</td><td>4,45</td><td>5,50</td><td>6,00</td><td>7,50</td><td colspan="2">8,50</td><td>10,00</td><td>12,00</td><td>1,25</td><td>96</td><td>60</td><td>7,0</td></tr>
<tr><td>15</td><td>8</td><td>2,50</td><td>2,85</td><td>3,20</td><td>3,70</td><td>4,05</td><td>4,60</td><td>5,50</td><td>6,50</td><td>7,50</td><td>9,00</td><td colspan="2">10,50</td><td>12,50</td><td>15,00</td><td>1,60</td><td>75</td><td>48</td><td>6,6</td></tr>
<tr><td>16</td><td rowspan="3">320 --- 18</td><td rowspan="3">240</td><td>3</td><td>1,90</td><td>2,10</td><td>2,30</td><td>2,60</td><td>2,75</td><td>3,05</td><td>3,40</td><td>4,00</td><td>4,65</td><td>5,50</td><td colspan="2">6,00</td><td>7,00</td><td>8,50</td><td>0,85</td><td>150</td><td>75</td><td>7,5</td></tr>
<tr><td>17</td><td>5</td><td>2,35</td><td>2,60</td><td>2,90</td><td>3,00</td><td>3,60</td><td>4,00</td><td>4,60</td><td>5,50</td><td>6,50</td><td>7,50</td><td colspan="2">9,00</td><td>10,00</td><td>12,00</td><td>1,25</td><td>96</td><td>48</td><td>7,1</td></tr>
<tr><td>18</td><td>8</td><td>3,00</td><td>3,45</td><td>3,90</td><td>4,50</td><td>4,95</td><td>5,50</td><td>6,40</td><td>8,00</td><td>9,00</td><td>11,0</td><td colspan="2">13,00</td><td>15,00</td><td>18,50</td><td>1,95</td><td>60</td><td>30</td><td>6,6</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="22%"><col width="28%"><col width="4%"><col width="4%"><col width="8%"><col width="4%"><col width="5%"><col width="2%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="2">Неполное штучное время Фрезерование плоскостей, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="2">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="8">Фрезы торцовые с пластинками Т5К10</td></tr>
<tr><td colspan="2">Единичное и мелкосерийное производство</td><td colspan="8">Карта 58 Лист 2</td></tr>
<tr><td colspan="10">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="5">Предела прочности стали и продолжительности обработки</td><td>Предел прочности сигма , ГПа в</td><td colspan="3">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td>Продолжительность обработки, мин.</td><td colspan="2">до 10</td><td>свыше 10</td><td colspan="3">-</td><td>до 10</td><td>свыше 10</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,9</td><td rowspan="3">0,8</td><td colspan="3"></td><td rowspan="3">1,0</td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td rowspan="4">Состояния обрабатываемой поверхности</td><td>Состояние обрабатываемой поверхности</td><td colspan="5">без корки и удара</td><td colspan="3">по корке и на удар</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="5"></td><td colspan="3" rowspan="3">1,2</td></tr>
<tr><td>1,0</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="2%"><col width="4%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="2%"><col width="7%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="13">Неполное штучное время Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="15">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="15">Фрезы торцовые с пластинками Т5К10</td></tr>
<tr><td colspan="13">Единичное и мелкосерийное производство</td><td colspan="15">Карта 59</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td colspan="2" rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="18">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td colspan="2">150</td><td>200</td><td>250</td><td>300</td><td>400</td><td colspan="2">500</td><td colspan="2">600</td><td>750</td><td colspan="2">950</td><td>Добавлять на каждые 100 мм свыше 950</td><td colspan="2" rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="18">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="14">7,5 - 10</td><td rowspan="2">80 -- 8</td><td colspan="2" rowspan="2">48</td><td>3</td><td>2,20</td><td>2,25</td><td>2,35</td><td>2,65</td><td colspan="2">2,70</td><td>2,80</td><td>2,95</td><td>3,75</td><td>4,00</td><td colspan="2">4,25</td><td colspan="2">4,9</td><td>5,0</td><td colspan="2">6,0</td><td>0,40</td><td colspan="2">380</td><td>600</td><td>3,8</td></tr>
<tr><td>2</td><td>5</td><td>2,30</td><td>2,40</td><td>2,45</td><td>2,80</td><td colspan="2">2,85</td><td>3,00</td><td>3,20</td><td>4,05</td><td>4,30</td><td colspan="2">4,65</td><td colspan="2">5,5</td><td>6,0</td><td colspan="2">6,5</td><td>0,48</td><td colspan="2">300</td><td>480</td><td>4,6</td></tr>
<tr><td>3</td><td rowspan="2">100 --- 8</td><td colspan="2" rowspan="2">60</td><td>3</td><td>2,35</td><td>2,45</td><td>2,55</td><td>2,85</td><td colspan="2">2,95</td><td>3,10</td><td>3,25</td><td>4,10</td><td>4,40</td><td colspan="2">4,75</td><td colspan="2">5,5</td><td>6,0</td><td colspan="2">6,5</td><td>0,48</td><td colspan="2">300</td><td>480</td><td>3,2</td></tr>
<tr><td>4</td><td>5</td><td>2,50</td><td>2,60</td><td>2,70</td><td>3,05</td><td colspan="2">3,15</td><td>3,35</td><td>3,55</td><td>4,45</td><td>4,80</td><td colspan="2">5,50</td><td colspan="2">6,0</td><td>6,5</td><td colspan="2">7,5</td><td>0,55</td><td colspan="2">240</td><td>380</td><td>4,6</td></tr>
<tr><td>5</td><td rowspan="2">125 --- 8</td><td colspan="2" rowspan="2">75</td><td>3</td><td>2,45</td><td>2,55</td><td>2,65</td><td>2,95</td><td colspan="2">3,05</td><td>3,20</td><td>3,35</td><td>4,20</td><td>4,45</td><td colspan="2">4,85</td><td colspan="2">5,5</td><td>6,0</td><td colspan="2">6,5</td><td>0,48</td><td colspan="2">300</td><td>380</td><td>4,6</td></tr>
<tr><td>6</td><td>5</td><td>2,60</td><td>2,70</td><td>2,85</td><td>3,15</td><td colspan="2">3,30</td><td>3,45</td><td>3,70</td><td>4,55</td><td>4,90</td><td colspan="2">5,50</td><td colspan="2">6,0</td><td>6,5</td><td colspan="2">7,5</td><td>0,55</td><td colspan="2">240</td><td>300</td><td>5,5</td></tr>
<tr><td>7</td><td rowspan="2">160 --- 10</td><td colspan="2" rowspan="2">112</td><td>3</td><td>2,75</td><td>2,90</td><td>3,00</td><td>3,30</td><td colspan="2">3,45</td><td>3,60</td><td>3,85</td><td>4,70</td><td>5,00</td><td colspan="2">5,50</td><td colspan="2">6,5</td><td>7,0</td><td colspan="2">7,5</td><td>0,55</td><td colspan="2">240</td><td>300</td><td>4,6</td></tr>
<tr><td>8</td><td>5</td><td>3,30</td><td>3,50</td><td>3,65</td><td>4,05</td><td colspan="2">4,25</td><td>4,55</td><td>4,90</td><td>6,00</td><td>6,50</td><td colspan="2">7,00</td><td colspan="2">8,5</td><td>9,0</td><td colspan="2">16,5</td><td>0,85</td><td colspan="2">150</td><td>240</td><td>6,6</td></tr>
<tr><td>9</td><td rowspan="2">200 --- 12</td><td colspan="2" rowspan="2">140</td><td>3</td><td>3,25</td><td>3,40</td><td>3,55</td><td>3,90</td><td colspan="2">4,05</td><td>4,25</td><td>4,55</td><td>5,50</td><td>6,00</td><td colspan="2">6,50</td><td colspan="2">7,5</td><td>8,0</td><td colspan="2">9,0</td><td>0,70</td><td colspan="2">190</td><td>240</td><td>5,5</td></tr>
<tr><td>10</td><td>5</td><td>4,05</td><td>4,30</td><td>4,50</td><td>4,95</td><td colspan="2">5,00</td><td>5,50</td><td>6,00</td><td>7,00</td><td>8,00</td><td colspan="2">8,50</td><td colspan="2">10,0</td><td>11,0</td><td colspan="2">12,5</td><td>1,00</td><td colspan="2">120</td><td>190</td><td>6,6</td></tr>
<tr><td>11</td><td rowspan="2">250 --- 14</td><td colspan="2" rowspan="2">190</td><td>3</td><td>4,00</td><td>4,15</td><td>4,35</td><td>4,75</td><td colspan="2">4,95</td><td>5,00</td><td>5,50</td><td>6,50</td><td>7,00</td><td colspan="2">8,00</td><td colspan="2">9,0</td><td>10,0</td><td colspan="2">11,0</td><td>0,85</td><td colspan="2">150</td><td>190</td><td>5,5</td></tr>
<tr><td>12</td><td>5</td><td>5,00</td><td>5,50</td><td>5,50</td><td>6,00</td><td colspan="2">6,50</td><td>7,00</td><td>7,50</td><td>9,00</td><td>9,50</td><td colspan="2">11,00</td><td colspan="2">12,5</td><td>13,5</td><td colspan="2">15,5</td><td>1,25</td><td colspan="2">96</td><td>150</td><td>6,6</td></tr>
<tr><td>13</td><td rowspan="2">320 --- 18</td><td colspan="2" rowspan="2">240</td><td>3</td><td>4,50</td><td>4,65</td><td>4,85</td><td>5,50</td><td colspan="2">3,50</td><td>5,50</td><td>6,00</td><td>7,00</td><td>7,50</td><td colspan="2">8,50</td><td colspan="2">9,5</td><td>10,5</td><td colspan="2">11,5</td><td>0,85</td><td colspan="2">150</td><td>150</td><td>6,0</td></tr>
<tr><td>14</td><td>5</td><td>6,00</td><td>6,50</td><td>6,50</td><td>7,00</td><td colspan="2">7,50</td><td>6,00</td><td>8,50</td><td>9,50</td><td>10,50</td><td colspan="2">11,50</td><td colspan="2">13,0</td><td>14,5</td><td colspan="2">16,5</td><td>1,25</td><td colspan="2">96</td><td>120</td><td>7,4</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td colspan="2">л</td><td>м</td><td colspan="2">н</td><td>о</td><td colspan="4"></td></tr>
<tr><td colspan="28">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Предела прочности стали и продолжительности</td><td colspan="7">Предел прочности сигма , ГПа в</td><td colspan="6">до 0,59</td><td colspan="5">0,59 - 0,74</td><td colspan="6">свыше 0,74</td></tr>
<tr><td colspan="4" rowspan="4">обработки</td><td colspan="7">Продолжительность обработки, мин.</td><td colspan="6">до 10 свыше 10</td><td colspan="5">-</td><td colspan="3">до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td colspan="7" rowspan="3">Коэффициент</td><td colspan="6" rowspan="3">0,9 0,8</td><td colspan="5"></td><td colspan="3" rowspan="3">1,0</td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="3%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="2%"><col width="7%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="12">Неполное штучное время Фрезерование плоскостей, Ra 2,5, 1Т9 квалитет</td><td colspan="13">Горизонтально-расточные станки</td></tr>
<tr><td colspan="12">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="13">Фрезы торцовые с пластинками Т15К16</td></tr>
<tr><td colspan="12">Единичное и мелкосерийное производство</td><td colspan="13">Карта 60</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="16">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td colspan="2">150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td colspan="2">950</td><td>Добавлять на каждые 100 мм свыше 950</td><td colspan="2" rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="16">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="7">7,5 - 10</td><td>80 -- 2</td><td>48</td><td rowspan="7">1</td><td>3,05</td><td>3,15</td><td>3,25</td><td>3,75</td><td colspan="2">3,85</td><td>4,0</td><td>4,20</td><td>4,35</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td colspan="2">7,5</td><td>0,60</td><td colspan="2">300</td><td>750</td><td rowspan="7">Не свыше 2,5</td></tr>
<tr><td>2</td><td>100 --- 8</td><td>60</td><td>3,25</td><td>3,35</td><td>3,50</td><td>4,05</td><td colspan="2">4,15</td><td>4,3</td><td>4,55</td><td>4,80</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td colspan="2">8,5</td><td>0,68</td><td colspan="2">240</td><td>600</td></tr>
<tr><td>3</td><td>125 --- 8</td><td>75</td><td>3,55</td><td>3,70</td><td>3,85</td><td>4,45</td><td colspan="2">4,60</td><td>4,8</td><td>5,00</td><td>5,50</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10,0</td><td>0,80</td><td colspan="2">190</td><td>480</td></tr>
<tr><td>4</td><td>160 --- 10</td><td>112</td><td>4,05</td><td>4,25</td><td>4,45</td><td>5,00</td><td colspan="2">5,50</td><td>6,0</td><td>6,00</td><td>6,00</td><td>7,5</td><td>8,5</td><td>9,5</td><td>10,5</td><td colspan="2">11,5</td><td>0,85</td><td colspan="2">150</td><td>380</td></tr>
<tr><td>5</td><td>200 --- 12</td><td>140</td><td>4,40</td><td>4,55</td><td>4,75</td><td>5,50</td><td colspan="2">5,50</td><td>6,0</td><td>6,00</td><td>6,50</td><td>8,0</td><td>8,5</td><td>10,0</td><td>10,5</td><td colspan="2">12,0</td><td>0,85</td><td colspan="2">150</td><td>300</td></tr>
<tr><td>6</td><td>250 --- 14</td><td>190</td><td>5,50</td><td>5,50</td><td>5,50</td><td>6,50</td><td colspan="2">6,50</td><td>7,0</td><td>7,50</td><td>8,00</td><td>9,5</td><td>10,5</td><td>11,5</td><td>13,0</td><td colspan="2">14,5</td><td>1,15</td><td colspan="2">120</td><td>240</td></tr>
<tr><td>7</td><td>320 --- 18</td><td>240</td><td>6,00</td><td>6,00</td><td>6,50</td><td>7,00</td><td colspan="2">7,50</td><td>7,5</td><td>8,00</td><td>8,50</td><td>10,0</td><td>11,0</td><td>12,5</td><td>13,5</td><td colspan="2">15,0</td><td>1,15</td><td colspan="2">120</td><td>190</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td colspan="2">н</td><td>о</td><td colspan="4"></td></tr>
<tr><td colspan="25">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="10">Предела прочности Предел прочности сигма , ГПа стали и в</td><td colspan="9">до 0,59 0,59 - 0,74</td><td colspan="6">свыше 0,74</td></tr>
<tr><td colspan="10">обработки Продолжительность обработки, мин.</td><td colspan="9">до 10 свыше 10 -</td><td colspan="3">до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td colspan="10" rowspan="3">Коэффициент</td><td colspan="9"></td><td colspan="3" rowspan="3">1,0</td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td colspan="6">0,9 0,8</td><td colspan="3">1,0</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="3%"><col width="2%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="12">Неполное штучное время Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="12">Горизонтально-расточные станки</td></tr>
<tr><td colspan="12" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="12">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="12">Карта 61</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="16">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td colspan="2">250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td colspan="2">950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="16">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="17">7,5 - 10</td><td rowspan="3">20 -- 5</td><td>20 - 30</td><td>3</td><td>1,40</td><td>1,55</td><td>1,65</td><td>1,85</td><td>2,00</td><td>2,15</td><td colspan="2">2,40</td><td>2,70</td><td>3,05</td><td>3,50</td><td>4,10</td><td>4,65</td><td colspan="2">5,50</td><td>0,55</td><td>240</td><td>750</td><td>Не свыше</td></tr>
<tr><td>2</td><td rowspan="2">20 - 40</td><td>3</td><td>1,35</td><td>1,45</td><td>1,55</td><td>1,75</td><td>1,85</td><td>2,00</td><td colspan="2">2,15</td><td>2,45</td><td>2,75</td><td>3,10</td><td>3,55</td><td>4,05</td><td colspan="2">4,65</td><td>0,47</td><td>300</td><td>480</td><td rowspan="16">1,5</td></tr>
<tr><td>3</td><td>5</td><td>1,50</td><td>1,60</td><td>1,75</td><td>2,00</td><td>2,15</td><td>2,40</td><td colspan="2">2,65</td><td>3,05</td><td>3,50</td><td>4,05</td><td>4,75</td><td>5,50</td><td colspan="2">6,50</td><td>0,70</td><td>190</td><td>380</td></tr>
<tr><td>4</td><td rowspan="2">25 -- 5</td><td rowspan="2">20 - 40</td><td>3</td><td>1,40</td><td>1,45</td><td>1,55</td><td>1,75</td><td>1,85</td><td>2,00</td><td colspan="2">2,15</td><td>2,45</td><td>2,75</td><td>3,10</td><td>3,60</td><td>4,05</td><td colspan="2">4,65</td><td>0,47</td><td>300</td><td>480</td></tr>
<tr><td>5</td><td>5</td><td>1,50</td><td>1,65</td><td>1,80</td><td>2,05</td><td>2,20</td><td>2,40</td><td colspan="2">2,70</td><td>3,10</td><td>3,50</td><td>4,10</td><td>4,75</td><td>5,50</td><td colspan="2">6,50</td><td>0,70</td><td>190</td><td>380</td></tr>
<tr><td>6</td><td rowspan="3">28 -- 5</td><td rowspan="3">20 - 50</td><td>3</td><td>1,40</td><td>1,45</td><td>1,55</td><td>1,75</td><td>1,85</td><td>2,00</td><td colspan="2">2,15</td><td>2,45</td><td>2,75</td><td>3,10</td><td>3,60</td><td>4,05</td><td colspan="2">4,65</td><td>0,47</td><td>300</td><td>380</td></tr>
<tr><td>7</td><td>5</td><td>1,50</td><td>1,65</td><td>1,80</td><td>2,05</td><td>2,20</td><td>2,40</td><td colspan="2">2,70</td><td>3,10</td><td>3,50</td><td>4,10</td><td>4,75</td><td>5,50</td><td colspan="2">6,50</td><td>0,70</td><td>190</td><td>300</td></tr>
<tr><td>8</td><td>8</td><td>1,70</td><td>1,90</td><td>2,15</td><td>2,50</td><td>2,70</td><td>3,05</td><td colspan="2">3,50</td><td>4,05</td><td>4,75</td><td>5,50</td><td>6,50</td><td>8,00</td><td colspan="2">9,50</td><td>1,00</td><td>120</td><td>240</td></tr>
<tr><td>9</td><td rowspan="3">32 -- 4</td><td rowspan="3">20 - 30</td><td>3</td><td>1,70</td><td>1,90</td><td>1,90</td><td>2,00</td><td>2,10</td><td>2,50</td><td colspan="2">2,40</td><td>2,80</td><td>3,10</td><td>3,40</td><td>4,00</td><td>4,50</td><td colspan="2">5,10</td><td>0,35</td><td>315</td><td>480</td></tr>
<tr><td>10</td><td>5</td><td>1,80</td><td>2,00</td><td>2,10</td><td>2,50</td><td>2,50</td><td>2,60</td><td colspan="2">3,00</td><td>3,50</td><td>3,90</td><td>4,50</td><td>5,50</td><td>6,00</td><td colspan="2">7,00</td><td>0,57</td><td>190</td><td>380</td></tr>
<tr><td>11</td><td>8</td><td>2,00</td><td>2,20</td><td>2,50</td><td>2,80</td><td>3,00</td><td>3,30</td><td colspan="2">3,80</td><td>4,50</td><td>5,00</td><td>6,00</td><td>7,50</td><td>8,50</td><td colspan="2">10,00</td><td>0,90</td><td>120</td><td>300</td></tr>
<tr><td>12</td><td rowspan="3">48 -- 4</td><td rowspan="3">20 - 30</td><td>3</td><td>1,70</td><td>1,80</td><td>1,90</td><td>2,10</td><td>2,20</td><td>2,40</td><td colspan="2">2,60</td><td>3,00</td><td>3,70</td><td>4,30</td><td>4,80</td><td>5,50</td><td colspan="2">0,35</td><td>300</td><td>480</td><td></td></tr>
<tr><td>13</td><td>5</td><td>1,90</td><td>2,00</td><td>2,20</td><td>2,40</td><td>2,60</td><td>2,80</td><td colspan="2">3,10</td><td>3,60</td><td>4,10</td><td>4,70</td><td>5,50</td><td>6,50</td><td colspan="2">7,50</td><td>0,65</td><td>175</td><td>300</td></tr>
<tr><td>14</td><td>8</td><td>2,00</td><td>2,20</td><td>2,50</td><td>2,80</td><td>3,00</td><td>3,30</td><td colspan="2">3,80</td><td>4,50</td><td>5,00</td><td>6,00</td><td>7,50</td><td>8,50</td><td colspan="2">10,00</td><td>0,90</td><td>115</td><td>300</td></tr>
<tr><td>15</td><td rowspan="3">50 -- 4</td><td rowspan="3">20 - 30</td><td>3</td><td>1,85</td><td>1,95</td><td>2,10</td><td>2,30</td><td>2,40</td><td>2,60</td><td colspan="2">2,90</td><td>3,20</td><td>3,60</td><td>4,00</td><td>4,30</td><td>5,50</td><td colspan="2">6,50</td><td>0,45</td><td>225</td><td>240</td></tr>
<tr><td>16</td><td>3</td><td>2,00</td><td>2,20</td><td>2,40</td><td>2,60</td><td>2,80</td><td>3,10</td><td colspan="2">3,50</td><td>4,00</td><td>4,50</td><td>5,00</td><td>6,00</td><td>7,00</td><td colspan="2">8,50</td><td>0,75</td><td>150</td><td>240</td></tr>
<tr><td>17</td><td>8</td><td>2,20</td><td>2,50</td><td>2,80</td><td>3,10</td><td>3,40</td><td>3,80</td><td colspan="2">4,40</td><td>5,00</td><td>6,00</td><td>7,00</td><td>8,50</td><td>10,00</td><td colspan="2">11,50</td><td>1,10</td><td>100</td><td>190</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td colspan="2">н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="24">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="19">Твердости чугуна и Твердость НВ, ГПа до 2,15</td><td colspan="5">свыше 2,15</td></tr>
<tr><td colspan="19">обработки Продолжительность обработки, мин. - до 10</td><td colspan="5">свыше 10</td></tr>
<tr><td colspan="19"></td><td colspan="5" rowspan="3">1,25</td></tr>
<tr><td colspan="10">Коэффициент</td><td colspan="9">1,0 1,1</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="22">Неполное штучное время Горизонтально-расточные станки Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 - 1Т9 квалитет</td></tr>
<tr><td colspan="22">Чугун серый, НВ = 1,76 - 2,15 ГПа Фрезы концевые из стали Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="18">Карта 62</td><td colspan="4">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="15">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="15">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="3">16 -- 4</td><td rowspan="3">12</td><td>10</td><td>2,9</td><td>3,0</td><td>3,1</td><td>3,7</td><td>3,8</td><td>4,0</td><td>4,2</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">0,90</td><td>190</td><td>600</td><td>1,1</td></tr>
<tr><td>2</td><td>20</td><td>3,0</td><td>3,1</td><td>3,2</td><td>3,8</td><td>4,0</td><td>4,3</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td colspan="2">1,05</td><td>150</td><td>600</td><td rowspan="2">1,6</td></tr>
<tr><td>3</td><td>30</td><td>3,2</td><td>3,4</td><td>3,6</td><td>4,4</td><td>4,6</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10</td><td>11,5</td><td>13,5</td><td colspan="2">1,45</td><td>96</td><td>380</td></tr>
<tr><td>4</td><td rowspan="4">20 -- 5</td><td rowspan="4">18</td><td>10</td><td>2,9</td><td>3,0</td><td>3,1</td><td>3,7</td><td>3,8</td><td>4,0</td><td>4,2</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">0,90</td><td>190</td><td>480</td><td>1,1</td></tr>
<tr><td>5</td><td>20</td><td>3,1</td><td>3,3</td><td>3,4</td><td>4,0</td><td>4,3</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,5</td><td colspan="2">1,20</td><td>120</td><td>380</td><td rowspan="3">1,6</td></tr>
<tr><td>6</td><td>30</td><td>3,2</td><td>3,4</td><td>3,6</td><td>4,5</td><td>4,7</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td colspan="2">1,45</td><td>96</td><td>300</td></tr>
<tr><td>7</td><td>40</td><td>3,4</td><td>3,6</td><td>3,9</td><td>4,8</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td>16,0</td><td colspan="2">1,75</td><td>75</td><td>300</td></tr>
<tr><td>8</td><td rowspan="3">25 -- 5</td><td rowspan="3">22</td><td>20</td><td>3,1</td><td>3,3</td><td>3,4</td><td>4,1</td><td>4,4</td><td>4,7</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td colspan="2">1,20</td><td>120</td><td>300</td><td>2,2</td></tr>
<tr><td>9</td><td>30</td><td>3,5</td><td>3,8</td><td>3,9</td><td>4,8</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>14,0</td><td>16,0</td><td colspan="2">1,75</td><td>75</td><td>240</td><td>1,9</td></tr>
<tr><td>10</td><td>45</td><td>3,7</td><td>4,1</td><td>3,4</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,0</td><td>19,0</td><td colspan="2">2,15</td><td>60</td><td>240</td><td>1,5</td></tr>
<tr><td>11</td><td rowspan="3">28 -- 5</td><td rowspan="3">25</td><td>20</td><td>3,2</td><td>3,4</td><td>3,5</td><td>4,2</td><td>4,4</td><td>4,7</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td colspan="2">1,20</td><td>120</td><td>300</td><td>2,2</td></tr>
<tr><td>12</td><td>30</td><td>3,5</td><td>3,8</td><td>4,0</td><td>4,9</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,0</td><td colspan="2">1,75</td><td>75</td><td>190</td><td>1,9</td></tr>
<tr><td>13</td><td>45</td><td>3,8</td><td>4,2</td><td>4,3</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,0</td><td>19,0</td><td colspan="2">2,15</td><td>60</td><td>190</td><td>1,5</td></tr>
<tr><td>14</td><td rowspan="3">32 -- 4</td><td rowspan="3">30</td><td>20</td><td>2,8</td><td>3,0</td><td>3,3</td><td>3,8</td><td>4,0</td><td>4,4</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td colspan="2">1,20</td><td>120</td><td>240</td><td>2,2</td></tr>
<tr><td>15</td><td>30</td><td>3,0</td><td>3,3</td><td>3,6</td><td>4,0</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td colspan="2">1,45</td><td>96</td><td>240</td><td>2,2</td></tr>
<tr><td>16</td><td>45</td><td>3,3</td><td>3,6</td><td>4,0</td><td>4,7</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td>15,5</td><td colspan="2">1,75</td><td>75</td><td>190</td><td>2,4</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="2%"><col width="3%"><col width="2%"><col width="3%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="5%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="24">Неполное штучное время Горизонтально-расточные станки Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 - 1Т9 квалитет</td></tr>
<tr><td colspan="24">Чугун серый, НВ = 1,76 - 2,15 ГПа Фрезы концевые из стали Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="20">Карта 62</td><td colspan="4">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td colspan="2">300</td><td colspan="2">400</td><td>500</td><td>600</td><td colspan="2">750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>17</td><td>32 -- 4</td><td>30</td><td>60</td><td>3,7</td><td>4,0</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td colspan="2">10,0</td><td>12,0</td><td>13,5</td><td colspan="2">16,5</td><td>19,5</td><td>2,15</td><td>60</td><td>150</td><td>2,4</td></tr>
<tr><td>18</td><td rowspan="4">40 -- 4</td><td rowspan="4">38</td><td>20</td><td>3,0</td><td>3,2</td><td>3,5</td><td>4,0</td><td>4,4</td><td>5,0</td><td>5,5</td><td colspan="2">6,5</td><td colspan="2">7,5</td><td>8,5</td><td>10,0</td><td colspan="2">11,5</td><td>13,5</td><td>1,45</td><td>96</td><td>190</td><td>1,9</td></tr>
<tr><td>19</td><td>30</td><td>3,3</td><td>3,6</td><td>3,9</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,0</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td>10,0</td><td>11,5</td><td colspan="2">13,5</td><td>15,5</td><td>1,75</td><td>75</td><td>190</td><td>2,2</td></tr>
<tr><td>20</td><td>45</td><td>3,6</td><td>4,0</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td colspan="2">10,0</td><td>12,0</td><td>14,0</td><td colspan="2">16,5</td><td>19,5</td><td>2,15</td><td>60</td><td>150</td><td>2,5</td></tr>
<tr><td>21</td><td>60</td><td>4,1</td><td>4,5</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>7,5</td><td colspan="2">10</td><td colspan="2">12,0</td><td>14,5</td><td>17,0</td><td colspan="2">20,0</td><td>24,0</td><td>2,60</td><td>47,5</td><td>150</td><td>2,8</td></tr>
<tr><td>22</td><td rowspan="4">50 -- 4</td><td>45</td><td>20</td><td>3,3</td><td>3,6</td><td>3,9</td><td>4,6</td><td>5,0</td><td>5,5</td><td>6,0</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td>10,0</td><td>11,5</td><td colspan="2">13,5</td><td>15,5</td><td>1,75</td><td>75</td><td>150</td><td>3,9</td></tr>
<tr><td>23</td><td></td><td>30</td><td>3,6</td><td>4,0</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,3</td><td>7,5</td><td colspan="2">8,5</td><td colspan="2">10,0</td><td>12,0</td><td>14,0</td><td colspan="2">16,5</td><td>19,5</td><td>2,15</td><td>60</td><td>120</td><td>2,2</td></tr>
<tr><td>24</td><td></td><td>45</td><td>4,1</td><td>4,6</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td colspan="2">12,0</td><td>14,5</td><td>17,0</td><td colspan="2">20,0</td><td>24,0</td><td>2,60</td><td>47,5</td><td>120</td><td>2,7</td></tr>
<tr><td>25</td><td></td><td>60</td><td>4,7</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td colspan="2">12,0</td><td colspan="2">14,5</td><td>17,5</td><td>20,5</td><td colspan="2">24,0</td><td>29,0</td><td>3,0</td><td>37,5</td><td>96</td><td>3,2</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td colspan="2">и</td><td>к</td><td>л</td><td colspan="2">м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="24">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="12">Твердости чугуна и Твердость чугуна НВ, ГПа</td><td colspan="6">до 2,15</td><td colspan="6">свыше 2,15</td></tr>
<tr><td colspan="12">обработки Продолжительность обработки, мин.</td><td colspan="6">-</td><td colspan="3">до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td colspan="12" rowspan="3">Коэффициент</td><td colspan="6"></td><td colspan="3" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td colspan="4"></td></tr>
<tr><td colspan="6"></td></tr>
<tr><td colspan="12">Формы Форма обрабатываемой поверхности</td><td colspan="6">Прямолинейная</td><td colspan="6">Криволинейная (фасонная)</td></tr>
<tr><td colspan="12">поверхности</td><td colspan="6"></td><td colspan="6" rowspan="3">1,2</td></tr>
<tr><td colspan="12" rowspan="2">Коэффициент</td><td colspan="2">1,0</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="3%"><col width="4%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="11">Неполное штучное время Фрезерование пазов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="13">Горизонтально-расточные станки</td></tr>
<tr><td colspan="11" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="13">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="13">Карта 63</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td>Глубина</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td rowspan="2">паза, t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td colspan="2">250</td><td>300</td><td>400</td><td>500</td><td colspan="2">600</td><td>750</td><td>950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="7">7,5 - 10</td><td>16</td><td>16</td><td>2,65</td><td>3,0</td><td>3,65</td><td>4,0</td><td>4,3</td><td>5,0</td><td colspan="2">6,0</td><td>6,5</td><td>7,5</td><td>9,5</td><td colspan="2">-</td><td>-</td><td>-</td><td colspan="2">-</td><td>75</td><td>480</td><td></td></tr>
<tr><td>2</td><td rowspan="2">20 -- 5</td><td>16</td><td>2,5</td><td>2,75</td><td>3,3</td><td>3,6</td><td>3,9</td><td>4,6</td><td colspan="2">5,0</td><td>5,5</td><td>6,5</td><td>8,0</td><td colspan="2">9,0</td><td>10,5</td><td>12,5</td><td colspan="2">1,15</td><td>96</td><td>380</td><td rowspan="3">1,0</td></tr>
<tr><td>3</td><td>20</td><td>3,65</td><td>3,0</td><td>3,65</td><td>4,0</td><td>4,3</td><td>5,0</td><td colspan="2">6,0</td><td>6,5</td><td>7,5</td><td>9,5</td><td colspan="2">11,0</td><td>12,5</td><td>15,5</td><td colspan="2">1,45</td><td>75</td><td>380</td></tr>
<tr><td>4</td><td rowspan="2">25 -- 5</td><td>20</td><td>2,7</td><td>3,0</td><td>3,8</td><td>4,1</td><td>4,5</td><td>5,5</td><td colspan="2">6,0</td><td>7,0</td><td>8,0</td><td>10,0</td><td colspan="2">11,5</td><td>13,5</td><td>16,0</td><td colspan="2">1,55</td><td>70</td><td>300</td></tr>
<tr><td>5</td><td>30</td><td>2,85</td><td>3,25</td><td>4,0</td><td>4,5</td><td>4,9</td><td>6,0</td><td colspan="2">6,5</td><td>7,5</td><td>9,0</td><td>11,0</td><td colspan="2">13,0</td><td>15,0</td><td>18,5</td><td colspan="2">1,80</td><td>60</td><td>300</td><td>1,9</td></tr>
<tr><td>6</td><td rowspan="2">32</td><td>20</td><td>2,85</td><td>3,25</td><td>4,0</td><td>4,5</td><td>4,9</td><td>6,0</td><td colspan="2">6,5</td><td>7,5</td><td>9,0</td><td>11,0</td><td colspan="2">13,0</td><td>15,0</td><td>18,5</td><td colspan="2">1,80</td><td>60</td><td>240</td><td>1,8</td></tr>
<tr><td>7</td><td>30</td><td>3,1</td><td>3,6</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,5</td><td colspan="2">8,0</td><td>9,0</td><td>11,0</td><td>13,0</td><td colspan="2">15,5</td><td>16,5</td><td>22,5</td><td colspan="2">2,30</td><td>48</td><td>240</td><td>2,2</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="3"></td></tr>
<tr><td colspan="24">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="16">Твердости чугуна и Твердость НВ, ГПа до 2,15</td><td colspan="8">свыше 2,15</td></tr>
<tr><td colspan="16">обработки Продолжительность обработки, мин. -</td><td colspan="4">до 10</td><td colspan="4">свыше 10</td></tr>
<tr><td colspan="16"></td><td colspan="4" rowspan="3">1,1</td><td colspan="4" rowspan="3">1,25</td></tr>
<tr><td colspan="11">Коэффициент</td><td colspan="5">1,0</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="16">Неполное штучное время Рисунок Фрезерование Т-образных пазов, Rz 40 - Rz 20, 1Т11 квалитет (не приводится)</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="6">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="6">Карта 64</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td>Глубина</td><td colspan="15">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td rowspan="2">паза, t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td colspan="2">250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="15">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="10">10</td><td>18 -- 6</td><td>8</td><td>3,5</td><td>3,5</td><td>4,0</td><td>4,5</td><td>5,0</td><td>5,5</td><td colspan="2">6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td>16,0</td><td>1,75</td><td>75</td><td>380</td><td rowspan="10">Не свыше 1,0</td></tr>
<tr><td>2</td><td>21 -- 8</td><td>9</td><td>3,5</td><td>3,5</td><td>4,0</td><td>4,5</td><td>5,0</td><td>5,5</td><td colspan="2">6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td>16,0</td><td>1,75</td><td>75</td><td>300</td></tr>
<tr><td>3</td><td>25 -- 8</td><td>10</td><td>3,0</td><td>3,5</td><td>3,5</td><td>4,5</td><td>4,5</td><td>5,0</td><td colspan="2">5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td>1,04</td><td>96</td><td>240</td></tr>
<tr><td>4</td><td>32 -- 8</td><td>14</td><td>3,0</td><td>3,5</td><td>4,0</td><td>4,5</td><td>4,5</td><td>5,0</td><td colspan="2">6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td>1,04</td><td>96</td><td>240</td></tr>
<tr><td>5</td><td>40 -- 8</td><td>18</td><td>3,5</td><td>4,0</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,0</td><td colspan="2">7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,0</td><td>14,0</td><td>16,5</td><td>1,75</td><td>75</td><td>190</td></tr>
<tr><td>6</td><td>50 -- 8</td><td>22</td><td>3,5</td><td>4,0</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,5</td><td colspan="2">7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,0</td><td>14,0</td><td>16,5</td><td>1,75</td><td>75</td><td>190</td></tr>
<tr><td>7</td><td>60 -- 8</td><td>28</td><td>4,0</td><td>4,5</td><td>3,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td colspan="2">8,0</td><td>9,5</td><td>10,5</td><td>12,5</td><td>12,5</td><td>16,5</td><td>20,0</td><td>2,15</td><td>60</td><td>120</td></tr>
<tr><td>8</td><td>72 -- 8</td><td>33</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>8,5</td><td colspan="2">9,5</td><td>11,0</td><td>13,0</td><td>14,5</td><td>15,0</td><td>20,5</td><td>23,5</td><td>2,60</td><td>48</td><td>120</td></tr>
<tr><td>9</td><td>85 -- 8</td><td>37</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,5</td><td>9,5</td><td>10,5</td><td colspan="2">11,5</td><td>13,5</td><td>15,5</td><td>17,5</td><td>19,0</td><td>25,0</td><td>30,5</td><td>3,20</td><td>38</td><td>96</td></tr>
<tr><td>10</td><td>95 -- 8</td><td>41</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>11,5</td><td>12,5</td><td colspan="2">14,5</td><td>16,5</td><td>19,5</td><td>21,5</td><td>23,0</td><td>31,5</td><td>37,5</td><td>4,25</td><td>30</td><td>75</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="22">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="22">Твердости чугуна Твердость чугуна НВ, ГПа до 2,15 свыше 2,15</td></tr>
<tr><td colspan="22">Продолжительность обработки, мин. - до 10 свыше 10</td></tr>
<tr><td colspan="22"></td></tr>
<tr><td colspan="11">Коэффициент</td><td colspan="11">1,0 1,1 1,25</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="6%"><col width="6%"><col width="6%"><col width="8%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="5%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="15">Неполное штучное время Фрезерование пазов типа "Ласточкин хвост", Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="15" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="8">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="8">Карта 65</td></tr>
<tr><td colspan="23">Рисунки (не приводятся)</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Глубина резания t, мм, до</td><td>Величина наклона</td><td colspan="15">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td rowspan="2">плоскости угла</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td colspan="2">500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="15">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="6">10</td><td>10 -- 8</td><td>6</td><td>70 - 80</td><td>2,6</td><td>2,7</td><td>2,8</td><td>3,0</td><td>3,3</td><td>3,5</td><td>3,6</td><td>4,0</td><td>4,3</td><td colspan="2">4,7</td><td>5,0</td><td>6,0</td><td>6,5</td><td>0,68</td><td>300</td><td>1500</td><td rowspan="6">Не свыше 1,0</td></tr>
<tr><td>2</td><td rowspan="2">16 -- 10</td><td rowspan="2">8</td><td>60 - 85</td><td>2,8</td><td>2,9</td><td>3,0</td><td>3,5</td><td>3,7</td><td>3,9</td><td>4,2</td><td>4,7</td><td>5,0</td><td colspan="2">5,5</td><td>6,0</td><td>7,5</td><td>8,5</td><td>0,90</td><td>190</td><td>750</td></tr>
<tr><td>3</td><td>70 - 80</td><td>2,7</td><td>2,8</td><td>2,9</td><td>3,4</td><td>3,5</td><td>3,6</td><td>3,9</td><td>4,3</td><td>4,7</td><td colspan="2">5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>0,75</td><td>240</td><td>960</td></tr>
<tr><td>4</td><td rowspan="3">25 -- 12</td><td rowspan="3">10</td><td>55 - 60</td><td>3,0</td><td>3,2</td><td>3,5</td><td>4,0</td><td>4,3</td><td>4,6</td><td>5,1</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td>8,5</td><td>9,5</td><td>11,5</td><td>1,25</td><td>120</td><td>480</td></tr>
<tr><td>5</td><td>65 - 70</td><td>2,8</td><td>2,9</td><td>3,1</td><td>3,6</td><td>3,7</td><td>3,9</td><td>4,2</td><td>4,7</td><td>5,5</td><td colspan="2">5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>0,90</td><td>190</td><td>600</td></tr>
<tr><td>6</td><td>75 - 80</td><td>2,7</td><td>2,8</td><td>2,8</td><td>3,3</td><td>3,4</td><td>3,5</td><td>3,7</td><td>4,0</td><td>4,4</td><td colspan="2">4,7</td><td>5,5</td><td>6,0</td><td>6,5</td><td>0,68</td><td>330</td><td>750</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="23">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="7">Твердости чугуна Твердость чугуна НВ, ГПа</td><td colspan="16">до 2,15 свыше 2,15</td></tr>
<tr><td colspan="7">Коэффициент</td><td colspan="16">1,0 1,1</td></tr>
</table>


<a id="p102092"></a>*Примечание.* Время в карте приведено на обработку паза типа "Ласточкин хвост" по предварительно прорезанному прямоугольному пазу.


<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="3%"><col width="2%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="11">Неполное штучное время Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="12">Горизонтально-расточные станки</td></tr>
<tr><td colspan="11">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="12">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="11">Единичное и мелкосерийное производство</td><td colspan="6">Карта 66</td><td colspan="6">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="15">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">N д, кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td colspan="2">750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="15">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="14">7,5 - 10</td><td>16 -- 4</td><td>20 - 30</td><td>3</td><td>1,55</td><td>1,70</td><td>1,90</td><td>2,20</td><td>2,40</td><td>2,65</td><td>3,00</td><td>3,50</td><td>4,05</td><td>4,75</td><td>5,50</td><td colspan="2">6,50</td><td>8,0</td><td>0,85</td><td>150</td><td>750</td><td rowspan="14">Не свыше 2,0</td></tr>
<tr><td>2</td><td rowspan="2">20 -- 5</td><td>20 - 40</td><td>3</td><td>1,40</td><td>1,55</td><td>1,65</td><td>1,85</td><td>2,00</td><td>2,15</td><td>2,40</td><td>2,70</td><td>3,05</td><td>3,50</td><td>4,10</td><td colspan="2">4,65</td><td>5,5</td><td>0,55</td><td>240</td><td>600</td></tr>
<tr><td>3</td><td>20 - 40</td><td>5</td><td>1,55</td><td>1,75</td><td>1,90</td><td>2,20</td><td>2,40</td><td>2,65</td><td>3,00</td><td>3,50</td><td>4,05</td><td>4,80</td><td>5,50</td><td colspan="2">6,50</td><td>8,0</td><td>0,85</td><td>150</td><td>480</td></tr>
<tr><td>4</td><td rowspan="2">25 -- 5</td><td rowspan="2">20 - 40</td><td>3</td><td>1,50</td><td>1,60</td><td>1,75</td><td>2,00</td><td>2,15</td><td>2,40</td><td>2,65</td><td>3,10</td><td>3,50</td><td>4,05</td><td>4,75</td><td colspan="2">5,50</td><td>6,5</td><td>0,70</td><td>190</td><td>480</td></tr>
<tr><td>5</td><td>5</td><td>1,65</td><td>1,90</td><td>2,10</td><td>2,45</td><td>2,70</td><td>3,00</td><td>3,50</td><td>4,05</td><td>4,75</td><td>5,50</td><td>6,50</td><td colspan="2">8,00</td><td>9,5</td><td>1,00</td><td>120</td><td>380</td></tr>
<tr><td>6</td><td rowspan="3">28 -- 5</td><td rowspan="3">20 - 50</td><td>3</td><td>1,50</td><td>1,60</td><td>1,75</td><td>2,00</td><td>2,15</td><td>2,40</td><td>2,65</td><td>3,10</td><td>3,50</td><td>4,05</td><td>4,75</td><td colspan="2">5,50</td><td>6,5</td><td>0,70</td><td>190</td><td>380</td></tr>
<tr><td>7</td><td>5</td><td>1,65</td><td>1,90</td><td>2,10</td><td>2,40</td><td>2,70</td><td>3,00</td><td>3,50</td><td>4,05</td><td>4,75</td><td>5,50</td><td>6,50</td><td colspan="2">8,00</td><td>9,5</td><td>1,00</td><td>120</td><td>300</td></tr>
<tr><td>8</td><td>8</td><td>1,95</td><td>2,35</td><td>2,70</td><td>3,20</td><td>3,55</td><td>4,10</td><td>4,80</td><td>5,50</td><td>6,50</td><td>8,00</td><td>10</td><td colspan="2">11,5</td><td>14</td><td>1,60</td><td>75</td><td>300</td></tr>
<tr><td>9</td><td rowspan="3">32 -- 4</td><td rowspan="3">20 - 50</td><td>3</td><td>1,80</td><td>1,90</td><td>2,10</td><td>2,30</td><td>2,40</td><td>2,60</td><td>2,90</td><td>3,20</td><td>3,60</td><td>4,00</td><td>4,80</td><td colspan="2">5,50</td><td>6,5</td><td>0,50</td><td>225</td><td>480</td></tr>
<tr><td>10</td><td>5</td><td>2,00</td><td>2,20</td><td>2,40</td><td>2,70</td><td>2,90</td><td>3,20</td><td>3,50</td><td>4,00</td><td>4,60</td><td>5,50</td><td>6,50</td><td colspan="2">7,50</td><td>9,0</td><td>0,75</td><td>140</td><td>380</td></tr>
<tr><td>11</td><td>8</td><td>2,30</td><td>2,50</td><td>2,80</td><td>3,20</td><td>3,50</td><td>4,00</td><td>4,70</td><td>5,50</td><td>6,00</td><td>7,50</td><td>9,00</td><td colspan="2">10,5</td><td>12,5</td><td>1,20</td><td>90</td><td>300</td></tr>
<tr><td>12</td><td rowspan="3">40 -- 4</td><td rowspan="3">20 - 50</td><td>3</td><td>1,90</td><td>2,00</td><td>2,20</td><td>2,50</td><td>2,70</td><td>2,90</td><td>3,30</td><td>3,60</td><td>4,10</td><td>4,70</td><td>5,60</td><td colspan="2">6,40</td><td>7,5</td><td>0,60</td><td>175</td><td>300</td></tr>
<tr><td>13</td><td>5</td><td>2,10</td><td>2,30</td><td>2,60</td><td>2,90</td><td>3,10</td><td>3,50</td><td>4,10</td><td>4,60</td><td>5,50</td><td>6,00</td><td>7,50</td><td colspan="2">8,50</td><td>10,5</td><td>0,90</td><td>115</td><td>240</td></tr>
<tr><td>14</td><td>8</td><td>2,40</td><td>2,70</td><td>3,00</td><td>3,50</td><td>3,80</td><td>4,30</td><td>5,00</td><td>6,00</td><td>7,00</td><td>8,50</td><td>10,0</td><td colspan="2">11,5</td><td>14</td><td>1,40</td><td>80</td><td>190</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td colspan="2">м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="3%"><col width="2%"><col width="3%"><col width="2%"><col width="4%"><col width="7%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"></colgroup>
<tr><td colspan="13">Неполное штучное время Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="16">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="16">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="13">Единичное и мелкосерийное производство</td><td colspan="9">Карта 66</td><td colspan="7">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="20">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td colspan="2">100</td><td colspan="2">125</td><td>150</td><td>200</td><td>250</td><td>300</td><td colspan="2">400</td><td colspan="2">500</td><td colspan="2">600</td><td colspan="2">750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="20">Время на проход, мин.</td></tr>
<tr><td>15</td><td rowspan="3">7,5 - 10</td><td rowspan="3">50 -- 4</td><td rowspan="3">20 - 50</td><td>3</td><td>2,00</td><td>2,20</td><td colspan="2">2,40</td><td colspan="2">2,70</td><td>2,90</td><td>3,20</td><td>3,50</td><td>4,00</td><td colspan="2">4,60</td><td colspan="2">5,50</td><td colspan="2">6,50</td><td colspan="2">7,50</td><td>9,0</td><td>0,75</td><td>140</td><td colspan="2">190</td><td rowspan="3">Не свыше 2,0</td></tr>
<tr><td>16</td><td>5</td><td>2,30</td><td>2,50</td><td colspan="2">2,80</td><td colspan="2">3,20</td><td>3,50</td><td>4,00</td><td>4,70</td><td>5,50</td><td colspan="2">6,00</td><td colspan="2">7,40</td><td colspan="2">9,00</td><td colspan="2">10,5</td><td>13,0</td><td>1,20</td><td>90</td><td colspan="2">150</td></tr>
<tr><td>17</td><td>8</td><td>2,50</td><td>2,90</td><td colspan="2">3,30</td><td colspan="2">3,80</td><td>4,20</td><td>4,70</td><td>5,50</td><td>6,40</td><td colspan="2">7,50</td><td colspan="2">9,50</td><td colspan="2">11,00</td><td colspan="2">13,00</td><td>16,0</td><td>1,60</td><td>70</td><td colspan="2">190</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td colspan="2">в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td colspan="2">к</td><td colspan="2">л</td><td colspan="2">м</td><td>н</td><td>о</td><td colspan="4"></td></tr>
<tr><td colspan="29">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">Группы обрабатываемой стали, предела</td><td colspan="5">Группа стали</td><td colspan="10">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="11">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3" rowspan="5">прочности и продолжительности работы</td><td colspan="5">Предел прочности сигма , в ГПа</td><td colspan="10">до 0,59 0,59 - 0,74 свыше 0,74</td><td colspan="4">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="4">свыше 0,74</td></tr>
<tr><td colspan="5">Продолжительность обработки, мин.</td><td colspan="2">до 10</td><td colspan="6">свыше - до 10 10</td><td colspan="2">свыше 10</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td><td colspan="2">до 10</td><td>свыше 10</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,9</td><td colspan="6"></td><td colspan="2" rowspan="3">1,25</td><td colspan="2"></td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,1</td><td rowspan="3">1,2</td><td colspan="2" rowspan="3">1,2</td><td colspan="2" rowspan="3">1,35</td></tr>
<tr><td colspan="2">0,8</td><td colspan="4">1,0 1,1</td><td colspan="2">1,0</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="6%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="13">Неполное штучное время Фрезерование уступов, Rz 40 - Rz 20, 1Т11 - 1Т9 квалитет</td><td colspan="10">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="10">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="13">Единичное и мелкосерийное производство</td><td colspan="6">Карта 67</td><td colspan="4">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="16">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td colspan="2">400</td><td>500</td><td>600</td><td>750</td><td>950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="16">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="3">16 -- 4</td><td rowspan="3">12</td><td>10</td><td>3,0</td><td>3,1</td><td>3,2</td><td>3,8</td><td>4,0</td><td>4,3</td><td>4,6</td><td>5,0</td><td colspan="2">5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,6</td><td colspan="2">1,05</td><td>150</td><td>750</td><td>1,1</td></tr>
<tr><td>2</td><td>20</td><td>3,1</td><td>3,2</td><td>3,4</td><td>4,0</td><td>4,3</td><td>4,8</td><td>5,0</td><td>5,5</td><td colspan="2">6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,5</td><td colspan="2">1,20</td><td>120</td><td>500</td><td>1,8</td></tr>
<tr><td>3</td><td>30</td><td>3,3</td><td>3,6</td><td>3,8</td><td>4,8</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td>16,0</td><td colspan="2">1,75</td><td>75</td><td>480</td><td>1,5</td></tr>
<tr><td>4</td><td rowspan="4">20 -- 5</td><td rowspan="4">18</td><td>10</td><td>3,0</td><td>3,1</td><td>3,2</td><td>3,9</td><td>4,0</td><td>4,3</td><td>4,7</td><td>5,0</td><td colspan="2">6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td colspan="2">1,05</td><td>150</td><td>480</td><td>1,8</td></tr>
<tr><td>5</td><td>20</td><td>3,1</td><td>3,2</td><td>3,4</td><td>4,1</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,0</td><td colspan="2">6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,5</td><td colspan="2">1,20</td><td>120</td><td>480</td><td>2,6</td></tr>
<tr><td>6</td><td>30</td><td>3,4</td><td>3,6</td><td>3,9</td><td>4,8</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td>10</td><td>11,5</td><td>13,5</td><td>16,0</td><td colspan="2">1,75</td><td>75</td><td>380</td><td>2,2</td></tr>
<tr><td>7</td><td>40</td><td>3,6</td><td>3,9</td><td>4,2</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td>11,5</td><td>13,5</td><td>16</td><td>19,0</td><td colspan="2">2,15</td><td>60</td><td>380</td><td>3,1</td></tr>
<tr><td>8</td><td rowspan="3">25 -- 5</td><td rowspan="3">22</td><td>20</td><td>3,3</td><td>3,4</td><td>3,6</td><td>4,4</td><td>4,7</td><td>5,0</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,0</td><td colspan="2">1,45</td><td>96</td><td>380</td><td>2,6</td></tr>
<tr><td>9</td><td>30</td><td>3,5</td><td>3,7</td><td>3,9</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td>10,0</td><td>11,5</td><td>14,0</td><td>16,0</td><td colspan="2">1,75</td><td>75</td><td>300</td><td>3,1</td></tr>
<tr><td>10</td><td>45</td><td>3,7</td><td>3,9</td><td>4,1</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td>12,0</td><td>14,0</td><td>16,0</td><td>19,0</td><td colspan="2">2,15</td><td>60</td><td>300</td><td>2,6</td></tr>
<tr><td>11</td><td rowspan="3">28 -- 5</td><td rowspan="3">25</td><td>20</td><td>3,3</td><td>3,5</td><td>3,7</td><td>4,5</td><td>4,7</td><td>5,0</td><td>6,0</td><td>6,5</td><td colspan="2">7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,0</td><td colspan="2">1,45</td><td>96</td><td>300</td><td>2,6</td></tr>
<tr><td>12</td><td>30</td><td>3,6</td><td>3,8</td><td>4,0</td><td>5,0</td><td>5,5</td><td>6,5</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,0</td><td colspan="2">1,75</td><td>75</td><td>240</td><td>2,8</td></tr>
<tr><td>13</td><td>45</td><td>3,8</td><td>4,0</td><td>4,3</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">10</td><td>12,0</td><td>14,0</td><td>16,0</td><td>19,0</td><td colspan="2">2,15</td><td>60</td><td>240</td><td>3,1</td></tr>
<tr><td>14</td><td rowspan="3">32 -- 4</td><td rowspan="3">30</td><td>20</td><td>3,0</td><td>3,2</td><td>3,5</td><td>4,1</td><td>4,4</td><td>4,9</td><td>5,5</td><td>6,0</td><td colspan="2">7,0</td><td>8,5</td><td>10,0</td><td>11,0</td><td>13,0</td><td colspan="2">1,45</td><td>96</td><td>300</td><td>2,7</td></tr>
<tr><td>15</td><td>30</td><td>3,3</td><td>3,6</td><td>3,9</td><td>4,6</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,5</td><td colspan="2">8,5</td><td>10</td><td>11,5</td><td>13,5</td><td>16,0</td><td colspan="2">1,75</td><td>75</td><td>300</td><td>2,9</td></tr>
<tr><td>16</td><td>45</td><td>3,6</td><td>4,0</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td>12</td><td>14</td><td>16,5</td><td>19,5</td><td colspan="2">2,15</td><td>60</td><td>200</td><td>3,2</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="6%"><col width="4%"><col width="3%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="3%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="5%"></colgroup>
<tr><td colspan="28">Неполное штучное время Горизонтально-расточные станки Фрезерование уступов, Rz 40 - Rz 20, 1Т11 - 1Т9 квалитет</td></tr>
<tr><td colspan="28">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Фрезы концевые из стали Р6М5 в</td></tr>
<tr><td colspan="28">Единичное и мелкосерийное производство Карта 67 Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td colspan="2" rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="19">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td colspan="2">125</td><td>150</td><td>200</td><td>250</td><td colspan="2">300</td><td colspan="2">400</td><td>500</td><td>600</td><td>750</td><td colspan="2">950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td colspan="2" rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="19">Время на проход, мин.</td></tr>
<tr><td>17</td><td>32 -- 4</td><td colspan="2">30</td><td>60</td><td>4,1</td><td>4,6</td><td>5,0</td><td colspan="2">6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td colspan="2">12,0</td><td>14,0</td><td>17,0</td><td>20,0</td><td colspan="2">24,0</td><td colspan="2">2,60</td><td>47,5</td><td colspan="2">150</td><td>3,1</td></tr>
<tr><td>18</td><td rowspan="4">40 -- 4</td><td colspan="2" rowspan="4">38</td><td>20</td><td>3,0</td><td>3,2</td><td>3,5</td><td colspan="2">4,1</td><td>4,4</td><td>4,9</td><td>5,5</td><td colspan="2">6,5</td><td colspan="2">7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td colspan="2">13,5</td><td colspan="2">1,75</td><td>75,0</td><td colspan="2">200</td><td>2,7</td></tr>
<tr><td>19</td><td>30</td><td>3,5</td><td>4,0</td><td>4,4</td><td colspan="2">5,0</td><td>5,5</td><td>6,0</td><td>7,0</td><td colspan="2">8,5</td><td colspan="2">10,0</td><td>11,5</td><td>14,0</td><td>16,0</td><td colspan="2">19,0</td><td colspan="2">2,15</td><td>60,0</td><td colspan="2">200</td><td>2,9</td></tr>
<tr><td>20</td><td>45</td><td>4,0</td><td>4,5</td><td>5,0</td><td colspan="2">6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td colspan="2">12,0</td><td>14,0</td><td>17,0</td><td>19,5</td><td colspan="2">23,5</td><td colspan="2">2,60</td><td>47,5</td><td colspan="2">150</td><td>3,2</td></tr>
<tr><td>21</td><td>60</td><td>4,6</td><td>5,0</td><td>6,0</td><td colspan="2">7,0</td><td>7,5</td><td>8,5</td><td>10,0</td><td colspan="2">12,0</td><td colspan="2">14,5</td><td>17,5</td><td>20,5</td><td>24,0</td><td colspan="2">29,0</td><td colspan="2">3,00</td><td>37,5</td><td colspan="2">125</td><td>3,0</td></tr>
<tr><td>22</td><td rowspan="4">50 -- 4</td><td colspan="2" rowspan="4">45</td><td>20</td><td>3,5</td><td>4,0</td><td>4,4</td><td colspan="2">5,0</td><td>5,5</td><td>6,5</td><td>7,0</td><td colspan="2">8,5</td><td colspan="2">10,0</td><td>11,5</td><td>14,0</td><td>16,0</td><td colspan="2">19,5</td><td colspan="2">2,15</td><td>60,0</td><td colspan="2">200</td><td>2,9</td></tr>
<tr><td>23</td><td>30</td><td>4,0</td><td>4,5</td><td>5,0</td><td colspan="2">6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td colspan="2">12,0</td><td>14,0</td><td>17,0</td><td>19,5</td><td colspan="2">23,5</td><td colspan="2">2,60</td><td>47,5</td><td colspan="2">150</td><td>3,0</td></tr>
<tr><td>24</td><td>45</td><td>4,5</td><td>5,0</td><td>6,0</td><td colspan="2">7,0</td><td>7,5</td><td>8,5</td><td>10,0</td><td colspan="2">12,0</td><td colspan="2">14,5</td><td>17,5</td><td>20,5</td><td>24,0</td><td colspan="2">29,0</td><td colspan="2">3,00</td><td>37,5</td><td colspan="2">125</td><td>3,1</td></tr>
<tr><td>25</td><td>60</td><td>5,5</td><td>6,0</td><td>7,0</td><td colspan="2">8,0</td><td>9,0</td><td>10,5</td><td>12,5</td><td colspan="2">14,5</td><td colspan="2">17,5</td><td>21,0</td><td>25,0</td><td>30,0</td><td colspan="2">36,0</td><td colspan="2">3,30</td><td>30,0</td><td colspan="2">100</td><td>3,1</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td colspan="2">н</td><td colspan="2">о</td><td colspan="4"></td></tr>
<tr><td colspan="28">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">Обрабатываемой стали, предела прочности и</td><td colspan="4">Группа стали</td><td colspan="21">Углеродистые, хромистые, никелевые, Марганцовистые, хромомарганцовистые, хромоникелевые хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3">продолжительности</td><td colspan="4">Предел прочности</td><td colspan="4">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="7">свыше 0,74 до 0,59</td><td colspan="7">0,59 - 0,74 свыше 0,74</td></tr>
<tr><td colspan="3" rowspan="4">обработки</td><td colspan="4">Продолжительность обработки, мин.</td><td colspan="2">до 10</td><td colspan="2">свыше 10</td><td colspan="3">-</td><td colspan="2">до 10</td><td colspan="3">свыше до 10 10</td><td colspan="2">свыше 10</td><td colspan="2">до 10</td><td colspan="3">свыше до 10 10</td><td colspan="2">свыше 10</td></tr>
<tr><td colspan="4" rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,9</td><td colspan="2" rowspan="3">0,8</td><td colspan="3"></td><td colspan="2" rowspan="3">1,1</td><td colspan="3"></td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,2 1,2</td><td colspan="2" rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td colspan="2"></td><td colspan="2">1,25</td><td>1,0</td></tr>
<tr><td colspan="3"></td><td colspan="3"></td></tr>
<tr><td colspan="3" rowspan="2">Форма обрабатываемой поверхности</td><td colspan="4">Форма обрабатываемой поверхности</td><td colspan="21">Прямолинейная Криволинейная (фасонная)</td></tr>
<tr><td colspan="4">Коэффициент</td><td colspan="21">1,0 1,2</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="6%"><col width="5%"><col width="2%"><col width="6%"><col width="5%"><col width="5%"><col width="4%"><col width="2%"><col width="3%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="3%"><col width="3%"><col width="2%"><col width="5%"><col width="2%"><col width="3%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"><col width="3%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="17">Неполное штучное время Фрезерование пазов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="13">Горизонтально-расточные станки</td></tr>
<tr><td colspan="17">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="13">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="17">Единичное и мелкосерийное производство</td><td colspan="13">Карта 68</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td colspan="2">Диаметр</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="21">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td colspan="2" rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td colspan="2">125</td><td>150</td><td>200</td><td colspan="2">250</td><td colspan="2">300</td><td colspan="2">400</td><td>500</td><td colspan="2">600</td><td colspan="2">750</td><td>950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td colspan="2" rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="21">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="7">7,5 - 10</td><td colspan="2">16 -- 4</td><td>16</td><td>2,85</td><td>3,25</td><td>4,0</td><td colspan="2">4,50</td><td>4,9</td><td>6,0</td><td colspan="2">6,5</td><td colspan="2">7,5</td><td colspan="2">9,0</td><td>11,0</td><td colspan="2">-</td><td colspan="2">-</td><td>-</td><td colspan="2">1,80</td><td colspan="2">75</td><td>480</td><td rowspan="7">Не свыше 2,0</td></tr>
<tr><td>2</td><td colspan="2" rowspan="2">20 -- 5</td><td>16</td><td>2,70</td><td>3,00</td><td>3,8</td><td colspan="2">4,10</td><td>4,5</td><td>5,5</td><td colspan="2">6,0</td><td colspan="2">7,0</td><td colspan="2">8,0</td><td>10,0</td><td colspan="2">11,5</td><td colspan="2">13,5</td><td>16,0</td><td colspan="2">1,55</td><td colspan="2">96</td><td>380</td></tr>
<tr><td>3</td><td>20</td><td>2,80</td><td>3,00</td><td>3,9</td><td colspan="2">4,30</td><td>4,8</td><td>5,5</td><td colspan="2">6,5</td><td colspan="2">7,0</td><td colspan="2">8,5</td><td>10,5</td><td colspan="2">12,0</td><td colspan="2">14,5</td><td>17,5</td><td colspan="2">1,70</td><td colspan="2">75</td><td>380</td></tr>
<tr><td>4</td><td colspan="2" rowspan="2">25 -- 5</td><td>20</td><td>2,85</td><td>3,25</td><td>4,0</td><td colspan="2">4,50</td><td>4,9</td><td>6,0</td><td colspan="2">6,5</td><td colspan="2">7,5</td><td colspan="2">9,0</td><td>11,0</td><td colspan="2">13,0</td><td colspan="2">15,0</td><td>18,5</td><td colspan="2">1,80</td><td colspan="2">75</td><td>300</td></tr>
<tr><td>5</td><td>30</td><td>3,05</td><td>3,35</td><td>4,4</td><td colspan="2">4,95</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td colspan="2">10,5</td><td>13,0</td><td colspan="2">15,0</td><td colspan="2">18,0</td><td>21,5</td><td colspan="2">2,20</td><td colspan="2">60</td><td>380</td></tr>
<tr><td>6</td><td colspan="2" rowspan="2">32 -- 4</td><td>20</td><td>3,05</td><td>3,55</td><td>4,4</td><td colspan="2">4,95</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td colspan="2">10,5</td><td>13,0</td><td colspan="2">15,0</td><td colspan="2">18,0</td><td>21,5</td><td colspan="2">2,20</td><td colspan="2">60</td><td>300</td></tr>
<tr><td>7</td><td>30</td><td>3,30</td><td>3,90</td><td>4,9</td><td colspan="2">5,50</td><td>6,5</td><td>7,5</td><td colspan="2">9,0</td><td colspan="2">10,5</td><td colspan="2">12,5</td><td>15,5</td><td colspan="2">18,0</td><td colspan="2">21,5</td><td>26,5</td><td colspan="2">2,75</td><td colspan="2">48</td><td>300</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td>д</td><td>е</td><td colspan="2">ж</td><td colspan="2">з</td><td colspan="2">и</td><td>к</td><td colspan="2">л</td><td colspan="2">м</td><td>н</td><td colspan="2">о</td><td colspan="4"></td></tr>
<tr><td colspan="30">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">Группы обрабатываемой стали, предела прочности и</td><td colspan="6">Группа стали</td><td colspan="11">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="10">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3" rowspan="5">продолжительности обработки</td><td colspan="6">Предел прочности сигма , в ГПа</td><td colspan="7">до 0,59 0,59 - 0,74</td><td colspan="4">свыше 0,74</td><td colspan="7">до 0,59 0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="6">Продолжительность обработки, мин.</td><td colspan="7">до 10 свыше - 10</td><td colspan="4">до 10 свыше 10</td><td colspan="2">до 10</td><td colspan="3">свыше до 10 10</td><td colspan="2">свыше 10</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="7"></td><td colspan="4" rowspan="3">1,1 1,25</td><td colspan="2"></td><td colspan="3" rowspan="3">1,1 1,1</td><td colspan="2" rowspan="3">1,2</td><td colspan="3" rowspan="3">1,2 1,35</td></tr>
<tr><td colspan="4">0,9 0,8</td><td colspan="2">1,0</td><td></td><td colspan="2">1,0</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="10">Неполное штучное время Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="12">Горизонтально-расточные станки</td></tr>
<tr><td colspan="10" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Единичное и мелкосерийное производство</td><td colspan="12">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="12">Карта 69 Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="14">7,5 - 10</td><td>16 -- 4</td><td>20 - 30</td><td>3</td><td>1,35</td><td>1,40</td><td>1,50</td><td>1,65</td><td>1,75</td><td>1,85</td><td>2,00</td><td>2,25</td><td>2,45</td><td>2,75</td><td>3,15</td><td>3,50</td><td>4,0</td><td>0,40</td><td>380</td><td>1200</td><td rowspan="14">Не свыше 2,0</td></tr>
<tr><td>2</td><td rowspan="2">20 -- 5</td><td rowspan="2">20 - 40</td><td>3</td><td>1,30</td><td>1,35</td><td>1,40</td><td>1,55</td><td>1,60</td><td>1,65</td><td>1,75</td><td>1,95</td><td>2,10</td><td>2,25</td><td>2,55</td><td>2,80</td><td>3,1</td><td>0,29</td><td>600</td><td>960</td></tr>
<tr><td>3</td><td>5</td><td>1,35</td><td>1,40</td><td>1,50</td><td>1,65</td><td>1,75</td><td>1,85</td><td>2,00</td><td>2,25</td><td>2,45</td><td>2,75</td><td>3,15</td><td>3,50</td><td>4,0</td><td>0,40</td><td>380</td><td>750</td></tr>
<tr><td>4</td><td rowspan="2">25 -- 5</td><td rowspan="2">20 - 40</td><td>3</td><td>1,30</td><td>1,35</td><td>1,45</td><td>1,60</td><td>1,65</td><td>1,75</td><td>1,85</td><td>2,05</td><td>2,25</td><td>2,45</td><td>2,80</td><td>3,10</td><td>3,5</td><td>0,34</td><td>480</td><td>750</td></tr>
<tr><td>5</td><td>5</td><td>1,35</td><td>1,40</td><td>1,50</td><td>1,65</td><td>1,75</td><td>1,85</td><td>2,00</td><td>2,25</td><td>2,45</td><td>2,75</td><td>3,15</td><td>3,50</td><td>4,0</td><td>0,40</td><td>380</td><td>750</td></tr>
<tr><td>6</td><td rowspan="3">28 -- 5</td><td rowspan="3">20 - 50</td><td>3</td><td>1,30</td><td>1,35</td><td>1,45</td><td>1,60</td><td>1,65</td><td>1,75</td><td>1,85</td><td>2,05</td><td>2,25</td><td>2,45</td><td>2,80</td><td>3,10</td><td>3,5</td><td>0,34</td><td>480</td><td>600</td></tr>
<tr><td>7</td><td>5</td><td>1,40</td><td>1,50</td><td>1,55</td><td>1,75</td><td>1,85</td><td>2,00</td><td>2,20</td><td>2,45</td><td>2,75</td><td>3,10</td><td>3,60</td><td>4,05</td><td>4,7</td><td>0,47</td><td>300</td><td>480</td></tr>
<tr><td>8</td><td>8</td><td>1,45</td><td>1,55</td><td>1,65</td><td>1,90</td><td>2,00</td><td>2,20</td><td>2,40</td><td>2,75</td><td>3,10</td><td>3,55</td><td>4,10</td><td>4,70</td><td>5,5</td><td>0,55</td><td>240</td><td>480</td></tr>
<tr><td>9</td><td rowspan="3">32 -- 4</td><td rowspan="3">20 - 50</td><td>3</td><td>1,70</td><td>1,80</td><td>1,90</td><td>2,00</td><td>2,10</td><td>2,20</td><td>2,30</td><td>2,60</td><td>2,80</td><td>3,10</td><td>3,70</td><td>4,10</td><td>4,6</td><td>0,30</td><td>380</td><td>480</td></tr>
<tr><td>10</td><td>5</td><td>1,80</td><td>1,90</td><td>2,00</td><td>2,10</td><td>2,20</td><td>2,40</td><td>2,60</td><td>2,90</td><td>3,20</td><td>3,50</td><td>4,10</td><td>4,60</td><td>5,0</td><td>0,35</td><td>300</td><td>380</td></tr>
<tr><td>11</td><td>8</td><td>1,80</td><td>1,90</td><td>2,00</td><td>2,20</td><td>2,30</td><td>2,50</td><td>2,80</td><td>3,10</td><td>3,50</td><td>3,90</td><td>4,60</td><td>5,00</td><td>6,0</td><td>0,45</td><td>240</td><td>380</td></tr>
<tr><td>12</td><td rowspan="3">40 -- 4</td><td rowspan="3">20 - 50</td><td>3</td><td>1,80</td><td>1,90</td><td>2,00</td><td>2,10</td><td>2,20</td><td>2,40</td><td>2,60</td><td>2,90</td><td>3,20</td><td>3,50</td><td>4,10</td><td>4,60</td><td>5,0</td><td>0,35</td><td>300</td><td>380</td></tr>
<tr><td>13</td><td>5</td><td>1,80</td><td>1,90</td><td>2,00</td><td>2,20</td><td>2,30</td><td>2,50</td><td>2,80</td><td>3,10</td><td>3,50</td><td>3,90</td><td>4,60</td><td>5,00</td><td>6,0</td><td>0,45</td><td>240</td><td>300</td></tr>
<tr><td>14</td><td>8</td><td>1,90</td><td>2,00</td><td>2,20</td><td>2,40</td><td>2,60</td><td>2,80</td><td>3,10</td><td>3,40</td><td>4,00</td><td>4,50</td><td>5,50</td><td>6,00</td><td>7,0</td><td>0,60</td><td>190</td><td>300</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="10">Неполное штучное время Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="12">Горизонтально-расточные станки</td></tr>
<tr><td colspan="10" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Единичное и мелкосерийное производство</td><td colspan="12">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="6">Карта 69</td><td colspan="6">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>15</td><td rowspan="3">7,5 - 10</td><td rowspan="3">50 -- 4</td><td rowspan="3">20 - 50</td><td>3</td><td>1,80</td><td>1,90</td><td>2,00</td><td>2,20</td><td>2,30</td><td>2,50</td><td>2,80</td><td>3,10</td><td>3,50</td><td>3,90</td><td>4,60</td><td>5,00</td><td>6,0</td><td>0,45</td><td>240</td><td>300</td><td rowspan="3">Не свыше 2,0</td></tr>
<tr><td>16</td><td>5</td><td>1,90</td><td>2,00</td><td>2,20</td><td>2,40</td><td>2,60</td><td>2,80</td><td>3,10</td><td>3,40</td><td>4,00</td><td>4,50</td><td>5,50</td><td>6,00</td><td>7,0</td><td>0,60</td><td>190</td><td>240</td></tr>
<tr><td>17</td><td>8</td><td>2,00</td><td>2,20</td><td>2,40</td><td>2,60</td><td>2,80</td><td>3,10</td><td>3,40</td><td>3,90</td><td>4,50</td><td>5,00</td><td>6,00</td><td>7,00</td><td>8,5</td><td>0,70</td><td>150</td><td>240</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="22">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="22">Группы медных сплавов Группа сплавов Гомогенные Гетерогенные</td></tr>
<tr><td colspan="13">Твердость НВ, ГПа 0,59 - 0,88</td><td colspan="9">0,98 - 1,37 1,47 - 2,45</td></tr>
<tr><td colspan="13" rowspan="3">Коэффициент 0,55</td><td colspan="9"></td></tr>
<tr><td>1,0</td><td colspan="8">1,25</td></tr>
<tr><td colspan="9"></td></tr>
<tr><td colspan="13">Группы алюминиевых Группа сплавов Силумин и литейные сплавы</td><td colspan="9">Дюралюминий</td></tr>
<tr><td colspan="13">Твердость НВ, ГПа до 0,64</td><td colspan="9">до 0,98</td></tr>
<tr><td colspan="13">Коэффициент 0,75</td><td colspan="9">0,7</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="21">Неполное штучное время Горизонтально-расточные станки Фрезерование уступов, Rz 40 - Rz 20, 1Т11 - 1Т9 квалитет</td></tr>
<tr><td colspan="21">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Фрезы концевые из стали Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="21">Карта 70 Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания, t, мм, до</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="3">16 -- 4</td><td rowspan="3">12</td><td>10</td><td>2,8</td><td>2,9</td><td>3,0</td><td>3,5</td><td>3,6</td><td>3,8</td><td>4,1</td><td>4,4</td><td>4,7</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>0,78</td><td>240</td><td>960</td><td>1,0</td></tr>
<tr><td>2</td><td>20</td><td>2,9</td><td>3,0</td><td>3,1</td><td>3,6</td><td>3,8</td><td>4,0</td><td>4,4</td><td>4,8</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>0,90</td><td>190</td><td>750</td><td>1,0</td></tr>
<tr><td>3</td><td>30</td><td>3,1</td><td>3,2</td><td>3,4</td><td>4,1</td><td>4,4</td><td>4,8</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,5</td><td>1,20</td><td>120</td><td>600</td><td>1,0</td></tr>
<tr><td>4</td><td rowspan="4">20 -- 5</td><td rowspan="4">18</td><td>10</td><td>2,8</td><td>2,9</td><td>3,0</td><td>3,5</td><td>3,6</td><td>3,8</td><td>4,1</td><td>4,4</td><td>4,7</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>0,78</td><td>240</td><td>750</td><td>1,7</td></tr>
<tr><td>5</td><td>20</td><td>2,9</td><td>3,0</td><td>3,1</td><td>3,6</td><td>3,8</td><td>4,0</td><td>4,4</td><td>4,8</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>0,90</td><td>190</td><td>600</td><td>2,4</td></tr>
<tr><td>6</td><td>30</td><td>3,0</td><td>3,1</td><td>3,2</td><td>3,9</td><td>4,1</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>1,05</td><td>150</td><td>480</td><td>1,2</td></tr>
<tr><td>7</td><td>40</td><td>3,2</td><td>3,4</td><td>3,6</td><td>4,4</td><td>4,7</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,5</td><td>1,45</td><td>36</td><td>380</td><td>1,7</td></tr>
<tr><td>8</td><td rowspan="3">25 -- 5</td><td rowspan="3">22</td><td>20</td><td>3,0</td><td>3,1</td><td>3,2</td><td>3,7</td><td>3,9</td><td>4,0</td><td>4,4</td><td>4,8</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>0,90</td><td>190</td><td>480</td><td>2,4</td></tr>
<tr><td>9</td><td>30</td><td>3,1</td><td>3,2</td><td>3,3</td><td>3,9</td><td>4,1</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>1,05</td><td>150</td><td>480</td><td>2,3</td></tr>
<tr><td>10</td><td>45</td><td>3,2</td><td>3,3</td><td>3,5</td><td>4,1</td><td>4,4</td><td>4,7</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>1,20</td><td>120</td><td>380</td><td>1,7</td></tr>
<tr><td>11</td><td rowspan="3">28 -- 5</td><td rowspan="3">25</td><td>20</td><td>3,0</td><td>3,1</td><td>3,2</td><td>3,7</td><td>3,9</td><td>4,1</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>0,90</td><td>190</td><td>420</td><td>2,4</td></tr>
<tr><td>12</td><td>30</td><td>3,1</td><td>3,2</td><td>3,3</td><td>3,9</td><td>4,1</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>1,05</td><td>150</td><td>480</td><td>2,0</td></tr>
<tr><td>13</td><td>45</td><td>3,2</td><td>3,3</td><td>3,5</td><td>4,2</td><td>4,5</td><td>4,8</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>1,20</td><td>120</td><td>380</td><td>1,8</td></tr>
<tr><td>14</td><td rowspan="3">32 -- 4</td><td rowspan="3">30</td><td>20</td><td>2,6</td><td>2,8</td><td>2,9</td><td>3,3</td><td>3,5</td><td>3,7</td><td>4,0</td><td>4,7</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>0,90</td><td>190</td><td>380</td><td>2,0</td></tr>
<tr><td>15</td><td>30</td><td>2,8</td><td>2,9</td><td>3,1</td><td>3,6</td><td>3,8</td><td>4,1</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>1,05</td><td>150</td><td>380</td><td>1,9</td></tr>
<tr><td>16</td><td>45</td><td>2,9</td><td>3,1</td><td>3,4</td><td>3,8</td><td>4,1</td><td>4,5</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,5</td><td>1,20</td><td>120</td><td>300</td><td>2,0</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="2%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="3%"><col width="2%"><col width="3%"><col width="2%"><col width="5%"><col width="2%"><col width="3%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="25">Неполное штучное время Горизонтально-расточные станки Фрезерование уступов, Rz 40 - Rz 20, 1Т11 - 1Т9 квалитет</td></tr>
<tr><td colspan="25">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые Фрезы концевые из стали Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="25">Карта 70 Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td colspan="2" rowspan="3">Глубина резания, t, мм, до</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">фрезы D, мм, и число зубьев z</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td colspan="2">500</td><td colspan="2">600</td><td>750</td><td colspan="2">950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>17</td><td>32 -- 4</td><td>30</td><td colspan="2">80</td><td>3,2</td><td>3,4</td><td>3,7</td><td>4,3</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td colspan="2">10,0</td><td>11,5</td><td colspan="2">13,5</td><td>1,45</td><td>96</td><td>300</td><td>2,1</td></tr>
<tr><td>18</td><td rowspan="4">40 -- 4</td><td rowspan="4">38</td><td colspan="2">20</td><td>2,7</td><td>2,9</td><td>3,1</td><td>3,5</td><td>3,8</td><td>4,0</td><td>4,4</td><td>5,0</td><td>5,5</td><td colspan="2">6,5</td><td colspan="2">7,5</td><td>8,5</td><td colspan="2">9,5</td><td>1,05</td><td>150</td><td>300</td><td>1,7</td></tr>
<tr><td>19</td><td colspan="2">30</td><td>2,9</td><td>3,1</td><td>3,3</td><td>3,8</td><td>4,1</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td>9,5</td><td colspan="2">11,5</td><td>1,20</td><td>120</td><td>240</td><td>2,0</td></tr>
<tr><td>20</td><td colspan="2">45</td><td>3,1</td><td>3,3</td><td>3,6</td><td>4,2</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td colspan="2">10,0</td><td>11,5</td><td colspan="2">13,5</td><td>1,45</td><td>96</td><td>200</td><td>2,2</td></tr>
<tr><td>21</td><td colspan="2">60</td><td>3,4</td><td>3,7</td><td>4,1</td><td>4,7</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td colspan="2">12,0</td><td>13,5</td><td colspan="2">16,0</td><td>1,75</td><td>75</td><td>200</td><td>2,4</td></tr>
<tr><td>22</td><td rowspan="4">50 -- 4</td><td rowspan="4">45</td><td colspan="2">20</td><td>2,9</td><td>3,1</td><td>3,3</td><td>3,8</td><td>4,1</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td>9,5</td><td colspan="2">11,5</td><td>1,20</td><td>120</td><td>240</td><td>1,7</td></tr>
<tr><td>23</td><td colspan="2">30</td><td>3,1</td><td>3,3</td><td>3,6</td><td>4,2</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td colspan="2">8,5</td><td colspan="2">10,0</td><td>11,5</td><td colspan="2">13,5</td><td>1,45</td><td>96</td><td>200</td><td>2,0</td></tr>
<tr><td>24</td><td colspan="2">45</td><td>3,4</td><td>3,7</td><td>4,6</td><td>4,7</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">10,0</td><td colspan="2">12,0</td><td>13,5</td><td colspan="2">16,0</td><td>1,75</td><td>75</td><td>200</td><td>2,4</td></tr>
<tr><td>25</td><td colspan="2">60</td><td>3,8</td><td>4,2</td><td>4,1</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,0</td><td colspan="2">12,0</td><td colspan="2">14,0</td><td>16,5</td><td colspan="2">19,5</td><td>2,15</td><td>60</td><td>200</td><td>2,8</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td colspan="2">к</td><td colspan="2">л</td><td>м</td><td colspan="2">н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="25">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4">Группы медных сплавов, твердости</td><td colspan="18">Группа сплавов Гомогенные</td><td colspan="3">Гетерогенные</td></tr>
<tr><td colspan="4" rowspan="5">и продолжительности обработки</td><td colspan="18">Твердость НВ, ГПа 0,59 - 0,74 0,98 - 1,37</td><td colspan="3">1,47 - 2,45</td></tr>
<tr><td colspan="11">Продолжительность обработки, до 10 мин.</td><td colspan="7">свыше 10 -</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="11" rowspan="3">Коэффициент 0,7</td><td colspan="7"></td><td colspan="3" rowspan="3">1,1 1,25</td></tr>
<tr><td colspan="5">0,55</td><td colspan="2">1,0</td></tr>
<tr><td colspan="7"></td></tr>
<tr><td colspan="4">Группы алюминиевых сплавов, твердости</td><td colspan="18">Группа сплавов Силумин и литейные сплавы</td><td colspan="3">Дюралюминий</td></tr>
<tr><td colspan="4" rowspan="3">и продолжительности обработки</td><td colspan="18">Твердость НВ, ГПа до 0,64</td><td colspan="3">до 0,98</td></tr>
<tr><td colspan="13">Продолжительность обработки до 10</td><td colspan="5">свыше 10</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="13">Коэффициент 0,75</td><td colspan="5">0,7</td><td colspan="3">0,75 0,7</td></tr>
<tr><td colspan="4" rowspan="4">Формы обрабатываемой поверхности</td><td colspan="13">Форма обрабатываемой Прямолинейная поверхности</td><td colspan="8">Криволинейная (фасонная)</td></tr>
<tr><td colspan="13"></td><td colspan="8" rowspan="3">1,2</td></tr>
<tr><td colspan="8">Коэффициент</td><td>1,0</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="4%"><col width="2%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="2%"><col width="3%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="5%"></colgroup>
<tr><td colspan="18">Неполное штучное время Фрезерование пазов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="18" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа и алюминиевые Единичное и мелкосерийное производство</td><td colspan="7">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="7">Карта 71</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td>Глубина резания</td><td colspan="18">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td colspan="2">75</td><td>100</td><td>125</td><td>150</td><td>200</td><td colspan="2">250</td><td>300</td><td>400</td><td>500</td><td colspan="2">600</td><td>750</td><td>950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="18">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="7">7,5 - 10</td><td>16 -- 4</td><td>16</td><td>1,65</td><td colspan="2">1,9</td><td>2,15</td><td>2,5</td><td>2,7</td><td>3,05</td><td colspan="2">3,5</td><td>4,05</td><td>4,75</td><td>5,5</td><td colspan="2">6,3</td><td>8,0</td><td>9,5</td><td colspan="2">1,0</td><td>120</td><td>750</td><td rowspan="7">Не свыше 1,5</td></tr>
<tr><td>2</td><td rowspan="2">20 -- 5</td><td>16</td><td>1,6</td><td colspan="2">1,8</td><td>1,95</td><td>2,25</td><td>2,45</td><td>2,7</td><td colspan="2">3,1</td><td>3,55</td><td>4,1</td><td>4,85</td><td colspan="2">5,5</td><td>6,5</td><td>8,0</td><td colspan="2">0,85</td><td>150</td><td>750</td></tr>
<tr><td>3</td><td>20</td><td>1,7</td><td colspan="2">1,95</td><td>2,15</td><td>2,5</td><td>2,75</td><td>3,1</td><td colspan="2">3,5</td><td>4,1</td><td>4,8</td><td>5,5</td><td colspan="2">6,5</td><td>8,0</td><td>9,5</td><td colspan="2">1,0</td><td>120</td><td>750</td></tr>
<tr><td>4</td><td rowspan="2">25 -- 5</td><td>20</td><td>1,65</td><td colspan="2">1,85</td><td>2,0</td><td>2,3</td><td>2,5</td><td>2,75</td><td colspan="2">3,1</td><td>3,6</td><td>4,15</td><td>4,9</td><td colspan="2">5,5</td><td>6,5</td><td>8,0</td><td colspan="2">0,85</td><td>150</td><td>600</td></tr>
<tr><td>5</td><td>30</td><td>1,75</td><td colspan="2">2,0</td><td>2,2</td><td>2,55</td><td>2,8</td><td>3,1</td><td colspan="2">3,6</td><td>4,15</td><td>4,85</td><td>5,5</td><td colspan="2">7,0</td><td>8,0</td><td>9,5</td><td colspan="2">1,0</td><td>120</td><td>600</td></tr>
<tr><td>6</td><td rowspan="2">32 -- 5</td><td>20</td><td>1,75</td><td colspan="2">2,0</td><td>2,25</td><td>2,55</td><td>2,8</td><td>3,15</td><td colspan="2">3,6</td><td>4,15</td><td>4,85</td><td>5,5</td><td colspan="2">7,0</td><td>8,0</td><td>9,5</td><td colspan="2">1,0</td><td>120</td><td>380</td></tr>
<tr><td>7</td><td>30</td><td>1,9</td><td colspan="2">2,2</td><td>2,5</td><td>2,9</td><td>3,15</td><td>3,6</td><td colspan="2">4,15</td><td>4,85</td><td>5,5</td><td>7,0</td><td colspan="2">8,0</td><td>9,5</td><td>11,5</td><td colspan="2">1,25</td><td>96</td><td>380</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж</td><td>з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="3"></td></tr>
<tr><td colspan="25">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6" rowspan="3">Группы медных сплавов и твердости</td><td colspan="6">Группа сплавов</td><td colspan="5">Гомогенные</td><td colspan="8">Гетерогенные</td></tr>
<tr><td colspan="6">Твердость НВ, ГПа</td><td colspan="5">0,59 - 0,74</td><td colspan="4">0,98 - 1,37</td><td colspan="4">1,47 - 2,15</td></tr>
<tr><td colspan="6">Коэффициент</td><td colspan="5">0,55</td><td colspan="4">1,0</td><td colspan="4">1,25</td></tr>
<tr><td colspan="6" rowspan="3">Группы алюминиевых сплавов и твердости</td><td colspan="6">Группа сплавов</td><td colspan="9">Силумин и литейные сплавы</td><td colspan="4">Дюралюминий</td></tr>
<tr><td colspan="6">Твердость НВ, ГПа</td><td colspan="9">до 0,64</td><td colspan="4">до 0,98</td></tr>
<tr><td colspan="6">Коэффициент</td><td colspan="9">0,75</td><td colspan="4">0,7</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="14">Неполное штучное время Фрезерование плоскостей и уступов, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="14" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="8">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="5">Карта 72</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="22">7,5 - 10</td><td rowspan="4">90 -- 10</td><td rowspan="2">6</td><td>12</td><td>1,15</td><td>1,3</td><td>1,45</td><td>1,8</td><td>1,95</td><td>2,15</td><td>2,45</td><td>2,95</td><td>3,4</td><td>4,0</td><td>4,65</td><td>5,5</td><td>6,5</td><td>0,7</td><td>190</td><td>120</td><td rowspan="22">Не свыше 2,0</td></tr>
<tr><td>2</td><td>18</td><td>1,3</td><td>1,5</td><td>1,65</td><td>2,05</td><td>2,25</td><td>2,55</td><td>2,9</td><td>3,45</td><td>4,0</td><td>4,75</td><td>5,5</td><td>6,5</td><td>8,0</td><td>0,85</td><td>150</td><td>96</td></tr>
<tr><td>3</td><td rowspan="2">18</td><td>5</td><td>1,05</td><td>1,15</td><td>1,25</td><td>1,6</td><td>1,7</td><td>1,9</td><td>2,1</td><td>2,55</td><td>2,9</td><td>3,35</td><td>3,9</td><td>4,5</td><td>5,5</td><td>0,55</td><td>240</td><td>150</td></tr>
<tr><td>4</td><td>12</td><td>1,15</td><td>1,3</td><td>1,45</td><td>1,8</td><td>1,95</td><td>2,15</td><td>2,45</td><td>2,95</td><td>3,4</td><td>4,0</td><td>4,65</td><td>5,5</td><td>6,5</td><td>0,7</td><td>190</td><td>120</td></tr>
<tr><td>5</td><td rowspan="4">100 --- 10</td><td rowspan="2">6</td><td>18</td><td>1,35</td><td>1,55</td><td>1,7</td><td>2,1</td><td>2,3</td><td>2,55</td><td>2,95</td><td>3,5</td><td>4,05</td><td>4,8</td><td>5,5</td><td>6,5</td><td>8,0</td><td>0,85</td><td>150</td><td>75</td></tr>
<tr><td>6</td><td>27</td><td>1,55</td><td>1,75</td><td>2,0</td><td>2,45</td><td>2,7</td><td>3,0</td><td>3,5</td><td>4,15</td><td>4,85</td><td>5,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td>1,0</td><td>120</td><td>60</td></tr>
<tr><td>7</td><td rowspan="2">18</td><td>5</td><td>1,15</td><td>1,25</td><td>1,4</td><td>1,8</td><td>1,9</td><td>2,15</td><td>2,45</td><td>2,95</td><td>3,35</td><td>3,95</td><td>4,65</td><td>5,5</td><td>6,5</td><td>0,7</td><td>190</td><td>96</td></tr>
<tr><td>8</td><td>12</td><td>1,3</td><td>1,5</td><td>1,65</td><td>2,05</td><td>2,25</td><td>2,5</td><td>2,9</td><td>3,45</td><td>4,0</td><td>4,75</td><td>5,5</td><td>6,5</td><td>7,5</td><td>0,85</td><td>150</td><td>75</td></tr>
<tr><td>9</td><td rowspan="4">125 --- 10</td><td rowspan="2">8</td><td>18</td><td>1,55</td><td>1,75</td><td>2,0</td><td>2,45</td><td>2,65</td><td>3,0</td><td>3,45</td><td>4,15</td><td>4,85</td><td>5,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td>1,0</td><td>120</td><td>60</td></tr>
<tr><td>10</td><td>27</td><td>1,85</td><td>2,1</td><td>2,4</td><td>2,9</td><td>3,2</td><td>3,6</td><td>4,2</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,5</td><td>1,25</td><td>96</td><td>48</td></tr>
<tr><td>11</td><td rowspan="2">27</td><td>5</td><td>1,25</td><td>1,45</td><td>1,6</td><td>2,0</td><td>2,2</td><td>2,45</td><td>2,85</td><td>3,4</td><td>3,95</td><td>4,7</td><td>5,5</td><td>6,5</td><td>7,5</td><td>0,85</td><td>150</td><td>75</td></tr>
<tr><td>12</td><td>12</td><td>1,45</td><td>1,7</td><td>1,95</td><td>7,4</td><td>2,6</td><td>2,95</td><td>3,4</td><td>4,1</td><td>4,75</td><td>5,5</td><td>6,5</td><td>8,0</td><td>9,5</td><td>1,0</td><td>120</td><td>75</td></tr>
<tr><td>13</td><td rowspan="5">160 --- 10</td><td rowspan="3">8</td><td>18</td><td>1,6</td><td>1,85</td><td>2,05</td><td>2,5</td><td>2,75</td><td>3,1</td><td>3,55</td><td>4,2</td><td>4,9</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>1,0</td><td>120</td><td>48</td></tr>
<tr><td>14</td><td>27</td><td>1,7</td><td>1,95</td><td>2,15</td><td>2,6</td><td>2,85</td><td>3,2</td><td>3,65</td><td>4,3</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>1,0</td><td>120</td><td>38</td></tr>
<tr><td>15</td><td>40</td><td>2,0</td><td>2,3</td><td>2,6</td><td>3,1</td><td>3,4</td><td>3,8</td><td>4,4</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10</td><td>12</td><td>1,25</td><td>96</td><td>30</td></tr>
<tr><td>16</td><td rowspan="2">40</td><td>5</td><td>1,25</td><td>1,45</td><td>1,85</td><td>2,05</td><td>2,2</td><td>2,5</td><td>2,85</td><td>3,45</td><td>4,0</td><td>4,7</td><td>5,5</td><td>6,5</td><td>8,0</td><td>0,85</td><td>150</td><td>60</td></tr>
<tr><td>17</td><td>12</td><td>1,4</td><td>1,55</td><td>1,75</td><td>2,15</td><td>2,35</td><td>2,6</td><td>2,95</td><td>3,55</td><td>4,1</td><td>4,85</td><td>5,5</td><td>6,5</td><td>8,0</td><td>0,85</td><td>150</td><td>48</td></tr>
<tr><td>18</td><td rowspan="5">200 --- 16</td><td rowspan="3">12</td><td>27</td><td>2,05</td><td>2,35</td><td>2,6</td><td>3,15</td><td>3,4</td><td>3,85</td><td>4,4</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10</td><td>12</td><td>1,25</td><td>96</td><td>38</td></tr>
<tr><td>19</td><td>40</td><td>2,55</td><td>2,9</td><td>3,3</td><td>3,85</td><td>4,25</td><td>4,8</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,5</td><td>12,5</td><td>15</td><td>1,6</td><td>75</td><td>30</td></tr>
<tr><td>20</td><td>60</td><td>3,2</td><td>3,7</td><td>4,15</td><td>4,8</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>15,5</td><td>18,5</td><td>1,95</td><td>60</td><td>24</td></tr>
<tr><td>21</td><td rowspan="2">40</td><td>5</td><td>1,3</td><td>1,5</td><td>1,65</td><td>2,05</td><td>2,25</td><td>2,55</td><td>2,9</td><td>3,5</td><td>4,05</td><td>4,75</td><td>5,5</td><td>6,5</td><td>8,0</td><td>0,85</td><td>150</td><td>48</td></tr>
<tr><td>22</td><td>12</td><td>1,6</td><td>1,8</td><td>2,05</td><td>2,5</td><td>2,75</td><td>3,05</td><td>3,55</td><td>4,2</td><td>4,9</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>1,0</td><td>120</td><td>38</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="16">Неполное штучное время Фрезерование плоскостей и уступов, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="9">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="9">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="6">Карта 72</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td colspan="2">50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td colspan="2">400</td><td colspan="2">500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>23</td><td rowspan="10">7,5 - 10</td><td rowspan="5">250 --- 20</td><td rowspan="3">12</td><td>27</td><td colspan="2">2,15</td><td>2,45</td><td>2,7</td><td>3,25</td><td>3,5</td><td>3,95</td><td>4,5</td><td>5,5</td><td colspan="2">6,0</td><td colspan="2">7,5</td><td>8,5</td><td>10</td><td>12</td><td>1,25</td><td>96</td><td>24</td><td rowspan="10">Не свыше 2,0</td></tr>
<tr><td>24</td><td>40</td><td colspan="2">2,75</td><td>3,1</td><td>3,45</td><td>4,05</td><td>4,4</td><td>4,95</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">9,0</td><td>11</td><td>12,5</td><td>15</td><td>1,6</td><td>75</td><td>19</td></tr>
<tr><td>25</td><td>60</td><td colspan="2">3,5</td><td>3,95</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,5</td><td colspan="2">9,5</td><td colspan="2">11,5</td><td>13,5</td><td>15,5</td><td>19</td><td>1,95</td><td>60</td><td>19</td></tr>
<tr><td>26</td><td rowspan="2">40</td><td>5</td><td colspan="2">1,45</td><td>1,7</td><td>1,95</td><td>2,4</td><td>2,6</td><td>2,95</td><td>3,4</td><td>4,1</td><td colspan="2">4,8</td><td colspan="2">5,5</td><td>6,5</td><td>8,0</td><td>9,5</td><td>1,0</td><td>120</td><td>38</td></tr>
<tr><td>27</td><td>12</td><td colspan="2">1,65</td><td>1,85</td><td>2,1</td><td>2,55</td><td>22,8</td><td>3,15</td><td>3,6</td><td>4,25</td><td colspan="2">4,95</td><td colspan="2">6,0</td><td>7,0</td><td>8,0</td><td>94</td><td>1,0</td><td>120</td><td>30</td></tr>
<tr><td>28</td><td rowspan="5">315 --- 22</td><td rowspan="3">12</td><td>27</td><td colspan="2">2,65</td><td>3,0</td><td>3,35</td><td>3,95</td><td>4,35</td><td>4,9</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">9,0</td><td>10,5</td><td>12,5</td><td>15</td><td>1,6</td><td>75</td><td>19</td></tr>
<tr><td>29</td><td>40</td><td colspan="2">3,45</td><td>3,95</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,5</td><td colspan="2">9,5</td><td colspan="2">11,5</td><td>13,5</td><td>15,5</td><td>19</td><td>1,95</td><td>60</td><td>15</td></tr>
<tr><td>30</td><td>60</td><td colspan="2">3,85</td><td>4,3</td><td>4,75</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">10</td><td colspan="2">12</td><td>14</td><td>16</td><td>19</td><td>1,95</td><td>60</td><td>15</td></tr>
<tr><td>31</td><td rowspan="2">40</td><td>5</td><td colspan="2">1,55</td><td>1,75</td><td>2,0</td><td>2,45</td><td>2,65</td><td>3,0</td><td>3,45</td><td>4,15</td><td colspan="2">4,85</td><td colspan="2">5,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td>1,0</td><td>120</td><td>30</td></tr>
<tr><td>32</td><td>12</td><td colspan="2">1,95</td><td>2,25</td><td>2,5</td><td>3,0</td><td>3,3</td><td>3,75</td><td>4,3</td><td>5,0</td><td colspan="2">6,0</td><td colspan="2">7,0</td><td>8,5</td><td>10</td><td>12</td><td>1,25</td><td>96</td><td>24</td></tr>
<tr><td colspan="5">Индекс</td><td colspan="2">а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="25">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6" rowspan="5">Твердости чугуна и продолжительности обработки</td><td colspan="9">Твердость НВ, ГПа</td><td colspan="10">до 2,15 свыше 2,15</td></tr>
<tr><td colspan="9">Продолжительность обработки, мин.</td><td colspan="10">- до 10 10</td></tr>
<tr><td colspan="9" rowspan="3">Коэффициент</td><td colspan="10"></td></tr>
<tr><td colspan="2">1,0</td><td colspan="8">1,1 1,25</td></tr>
<tr><td colspan="10"></td></tr>
<tr><td colspan="6" rowspan="4">Состояния обрабатываемой поверхности</td><td colspan="9">Состояние обрабатываемой поверхности</td><td colspan="10">без корки по корке</td></tr>
<tr><td colspan="9" rowspan="3">Коэффициент</td><td colspan="10"></td></tr>
<tr><td colspan="2">1,0</td><td colspan="8">1,2</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="16">Неполное штучное время Фрезерование плоскостей и уступов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="9">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="9">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="9">Карта 73</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы ремонта</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td colspan="2">50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td colspan="2">400</td><td colspan="2">500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="17">7,5 - 10</td><td>80 -- 10</td><td rowspan="17">2</td><td>18</td><td colspan="2">1,85</td><td>2,0</td><td>2,1</td><td>2,4</td><td>2,5</td><td>2,75</td><td>3,05</td><td>3,65</td><td colspan="2">4,05</td><td colspan="2">4,65</td><td>5,5</td><td>6,0</td><td>7,0</td><td>0,7</td><td>190</td><td>120</td><td rowspan="17">Не свыше 1,0</td></tr>
<tr><td>2</td><td rowspan="2">100 --- 10</td><td>18</td><td colspan="2">2,1</td><td>2,25</td><td>2,45</td><td>2,75</td><td>2,95</td><td>3,2</td><td>3,55</td><td>4,25</td><td colspan="2">4,8</td><td colspan="2">5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>0,85</td><td>150</td><td>96</td></tr>
<tr><td>3</td><td>27</td><td colspan="2">2,2</td><td>2,35</td><td>2,55</td><td>2,85</td><td>3,0</td><td>3,3</td><td>3,65</td><td>4,35</td><td colspan="2">4,9</td><td colspan="2">5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>0,85</td><td>150</td><td>96</td></tr>
<tr><td>4</td><td rowspan="2">125 --- 10</td><td>18</td><td colspan="2">2,4</td><td>2,65</td><td>2,85</td><td>3,2</td><td>3,45</td><td>3,73</td><td>4,2</td><td>5,0</td><td colspan="2">5,5</td><td colspan="2">6,5</td><td>7,5</td><td>9,0</td><td>10,5</td><td>1,0</td><td>120</td><td>75</td></tr>
<tr><td>5</td><td>27</td><td colspan="2">2,55</td><td>2,8</td><td>3,0</td><td>3,35</td><td>3,6</td><td>3,95</td><td>4,4</td><td>5,0</td><td colspan="2">6,0</td><td colspan="2">7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>1,0</td><td>120</td><td>75</td></tr>
<tr><td>6</td><td rowspan="3">160 --- 10</td><td>18</td><td colspan="2">2,25</td><td>2,45</td><td>2,65</td><td>2,9</td><td>3,1</td><td>3,4</td><td>3,75</td><td>4,45</td><td colspan="2">5,0</td><td colspan="2">5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>0,85</td><td>150</td><td>60</td></tr>
<tr><td>7</td><td>27</td><td colspan="2">2,75</td><td>2,95</td><td>3,2</td><td>3,55</td><td>3,75</td><td>4,1</td><td>4,55</td><td>5,5</td><td colspan="2">6,0</td><td colspan="2">7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>1,0</td><td>120</td><td>48</td></tr>
<tr><td>8</td><td>40</td><td colspan="2">3,3</td><td>3,6</td><td>3,85</td><td>4,25</td><td>4,55</td><td>6,0</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td>9,5</td><td>11</td><td>13</td><td>1,25</td><td>96</td><td>38</td></tr>
<tr><td>9</td><td rowspan="3">200 --- 16</td><td>27</td><td colspan="2">3,35</td><td>3,6</td><td>3,9</td><td>4,3</td><td>4,6</td><td>5,0</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td>10</td><td>11</td><td>13</td><td>1,25</td><td>96</td><td>38</td></tr>
<tr><td>10</td><td>40</td><td colspan="2">3,55</td><td>3,85</td><td>4,15</td><td>4,55</td><td>4,8</td><td>5,0</td><td>6,0</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td>10</td><td>11,5</td><td>13,5</td><td>1,25</td><td>96</td><td>38</td></tr>
<tr><td>11</td><td>60</td><td colspan="2">4,6</td><td>4,95</td><td>5,5</td><td>6,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">9,5</td><td colspan="2">11</td><td>12,5</td><td>14,5</td><td>17</td><td>1,6</td><td>75</td><td>30</td></tr>
<tr><td>12</td><td rowspan="3">250 --- 20</td><td>27</td><td colspan="2">3,55</td><td>3,85</td><td>4,1</td><td>4,5</td><td>4,8</td><td>5,0</td><td>6,0</td><td>6,5</td><td colspan="2">7,5</td><td colspan="2">8,5</td><td>10</td><td>11,5</td><td>13,5</td><td>1,25</td><td>96</td><td>30</td></tr>
<tr><td>13</td><td>40</td><td colspan="2">4,6</td><td>4,95</td><td>5,5</td><td>6,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">9,5</td><td colspan="2">11</td><td>12,5</td><td>14,5</td><td>17</td><td>1,6</td><td>75</td><td>24</td></tr>
<tr><td>14</td><td>60</td><td colspan="2">5,0</td><td>3,5</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10</td><td colspan="2">11,5</td><td>13,0</td><td>15</td><td>17,5</td><td>1,6</td><td>75</td><td>24</td></tr>
<tr><td>15</td><td rowspan="3">315 --- 22</td><td>27</td><td colspan="2">4,4</td><td>4,75</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td colspan="2">9,5</td><td colspan="2">11</td><td>12,5</td><td>14,5</td><td>17</td><td>1,6</td><td>75</td><td>24</td></tr>
<tr><td>16</td><td>40</td><td colspan="2">6,0</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,0</td><td>8,5</td><td>9,5</td><td>10,5</td><td colspan="2">12</td><td colspan="2">14</td><td>16</td><td>18</td><td>21,5</td><td>1,95</td><td>60</td><td>19</td></tr>
<tr><td>17</td><td>60</td><td colspan="2">6,5</td><td>7,0</td><td>7,5</td><td>8,0</td><td>8,5</td><td>9,5</td><td>10</td><td>11,5</td><td colspan="2">13</td><td colspan="2">14,5</td><td>16,5</td><td>19</td><td>22</td><td>1,95</td><td>60</td><td>19</td></tr>
<tr><td colspan="5">Индекс</td><td colspan="2">а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="25">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6" rowspan="5">Твердости чугуна и продолжительности обработки</td><td colspan="9">Твердость НВ, ГПа</td><td colspan="10">до 2,15 свыше 2,15</td></tr>
<tr><td colspan="9">Продолжительность обработки, мин.</td><td colspan="10">- до 10 свыше 10</td></tr>
<tr><td colspan="9" rowspan="3">Коэффициент</td><td colspan="10"></td></tr>
<tr><td colspan="2">1,0</td><td colspan="8">1,1 1,25</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="14">Неполное штучное время Фрезерование пазов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="14" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="8">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 74</td><td colspan="4">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="19">7,5 - 10</td><td rowspan="3">80 -- 10</td><td rowspan="3">25</td><td>5</td><td>1,6</td><td>1,7</td><td>1,8</td><td>2,05</td><td>2,15</td><td>2,3</td><td>2,55</td><td>3,1</td><td>3,45</td><td>3,9</td><td>4,45</td><td>5,0</td><td>6,0</td><td>0,55</td><td>240</td><td>190</td><td rowspan="19">Не свыше 3,0</td></tr>
<tr><td>2</td><td>10</td><td>1,75</td><td>1,9</td><td>2,05</td><td>2,3</td><td>2,45</td><td>2,65</td><td>2,95</td><td>3,55</td><td>4,0</td><td>4,55</td><td>5,5</td><td>6,0</td><td>7,0</td><td>0,7</td><td>190</td><td>190</td></tr>
<tr><td>3</td><td>15</td><td>1,95</td><td>2,15</td><td>2,35</td><td>2,65</td><td>2,8</td><td>3,1</td><td>3,45</td><td>4,15</td><td>4,7</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,5</td><td>0,85</td><td>150</td><td>150</td></tr>
<tr><td>4</td><td rowspan="4">100 --- 10</td><td rowspan="4">28</td><td>5</td><td>1,7</td><td>1,85</td><td>2,0</td><td>2,25</td><td>2,4</td><td>2,6</td><td>2,9</td><td>3,5</td><td>3,95</td><td>4,5</td><td>5,0</td><td>6,0</td><td>7,0</td><td>0,7</td><td>190</td><td>150</td></tr>
<tr><td>5</td><td>10</td><td>1,95</td><td>2,15</td><td>2,35</td><td>2,6</td><td>2,8</td><td>3,05</td><td>3,45</td><td>4,15</td><td>4,7</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,5</td><td>0,85</td><td>150</td><td>150</td></tr>
<tr><td>6</td><td>15</td><td>2,25</td><td>2,5</td><td>2,7</td><td>3,05</td><td>3,3</td><td>3,6</td><td>4,1</td><td>4,85</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10</td><td>1,0</td><td>120</td><td>150</td></tr>
<tr><td>7</td><td>20</td><td>2,6</td><td>2,9</td><td>3,2</td><td>3,6</td><td>3,85</td><td>4,3</td><td>4,85</td><td>6,0</td><td>6,5</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,5</td><td>1,25</td><td>96</td><td>120</td></tr>
<tr><td>8</td><td rowspan="4">125 --- 10</td><td rowspan="4">32</td><td>5</td><td>1,9</td><td>2,05</td><td>2,25</td><td>2,55</td><td>2,75</td><td>3,0</td><td>3,35</td><td>4,05</td><td>4,6</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,5</td><td>0,85</td><td>150</td><td>120</td></tr>
<tr><td>9</td><td>10</td><td>2,25</td><td>2,45</td><td>2,7</td><td>3,05</td><td>3,25</td><td>3,6</td><td>4,05</td><td>4,85</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10</td><td>1,0</td><td>120</td><td>120</td></tr>
<tr><td>10</td><td>15</td><td>2,65</td><td>2,9</td><td>3,2</td><td>3,6</td><td>3,9</td><td>4,3</td><td>4,9</td><td>6,0</td><td>6,5</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,5</td><td>1,25</td><td>96</td><td>96</td></tr>
<tr><td>11</td><td>20</td><td>3,2</td><td>3,6</td><td>3,95</td><td>4,4</td><td>4,8</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>15,5</td><td>1,6</td><td>75</td><td>96</td></tr>
<tr><td>12</td><td rowspan="5">160 --- 16</td><td rowspan="5">36</td><td>10</td><td>2,1</td><td>2,25</td><td>2,45</td><td>2,75</td><td>2,95</td><td>3,2</td><td>335</td><td>4,25</td><td>4,8</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>0,85</td><td>150</td><td>75</td></tr>
<tr><td>13</td><td>15</td><td>2,45</td><td>2,7</td><td>2,9</td><td>3,25</td><td>3,5</td><td>3,8</td><td>4,3</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,5</td><td>1,0</td><td>120</td><td>75</td></tr>
<tr><td>14</td><td>20</td><td>2,95</td><td>3,2</td><td>3,5</td><td>3,9</td><td>4,2</td><td>4,6</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>1,25</td><td>96</td><td>75</td></tr>
<tr><td>15</td><td>30</td><td>4,3</td><td>4,75</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,5</td><td>14</td><td>16,5</td><td>19,5</td><td>1,95</td><td>60</td><td>60</td></tr>
<tr><td>16</td><td>10</td><td>2,45</td><td>2,65</td><td>2,9</td><td>3,25</td><td>3,45</td><td>3,8</td><td>4,25</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,5</td><td>1,0</td><td>120</td><td>60</td></tr>
<tr><td rowspan="3">17</td><td rowspan="3">200 --- 16</td><td rowspan="3">40</td><td>15</td><td>2,95</td><td>3,25</td><td>3,5</td><td>3,9</td><td>4,2</td><td>4,65</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>1,25</td><td>96</td><td>60</td></tr>
<tr><td>20</td><td>3,1</td><td>3,4</td><td>3,7</td><td>4,1</td><td>4,35</td><td>4,8</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,5</td><td>9,5</td><td>11</td><td>13</td><td>1,25</td><td>96</td><td>60</td></tr>
<tr><td>30</td><td>4,7</td><td>5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,0</td><td>9,5</td><td>11</td><td>12,5</td><td>14,5</td><td>17</td><td>20</td><td>1,95</td><td>60</td><td>48</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="16">Неполное штучное время Фрезерование пазов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="8">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 74</td><td colspan="4">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="16">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td colspan="2">50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td colspan="2">400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="16">Время на проход, мин.</td></tr>
<tr><td>20</td><td rowspan="8">7,5 - 10</td><td rowspan="4">250 --- 20</td><td rowspan="4">45</td><td>10</td><td colspan="2">2,55</td><td>2,75</td><td>3,0</td><td>3,3</td><td>3,55</td><td>3,9</td><td>4,35</td><td>5,0</td><td colspan="2">6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>1,0</td><td>120</td><td>48</td><td rowspan="8">Не свыше 3,0</td></tr>
<tr><td>21</td><td>15</td><td colspan="2">3,1</td><td>3,35</td><td>3,65</td><td>4,05</td><td>4,35</td><td>4,75</td><td>5,5</td><td>6,0</td><td colspan="2">7,0</td><td>8,0</td><td>9,5</td><td>11</td><td>13</td><td>1,25</td><td>96</td><td>48</td></tr>
<tr><td>22</td><td>20</td><td colspan="2">3,3</td><td>3,6</td><td>3,85</td><td>4,25</td><td>4,55</td><td>5,0</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td>8,5</td><td>9,5</td><td>11</td><td>13</td><td>1,25</td><td>96</td><td>48</td></tr>
<tr><td>23</td><td>30</td><td colspan="2">5,0</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>10</td><td colspan="2">11</td><td>13</td><td>15</td><td>17</td><td>20</td><td>1,95</td><td>60</td><td>38</td></tr>
<tr><td>24</td><td rowspan="4">315 --- 22</td><td rowspan="4">50</td><td>10</td><td colspan="2">2,65</td><td>2,9</td><td>3,1</td><td>3,45</td><td>3,7</td><td>4,0</td><td>4,5</td><td>5,5</td><td colspan="2">6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>1,0</td><td>120</td><td>38</td></tr>
<tr><td>25</td><td>15</td><td colspan="2">3,25</td><td>3,55</td><td>3,8</td><td>4,2</td><td>4,5</td><td>4,95</td><td>5,5</td><td>6,5</td><td colspan="2">7,5</td><td>8,5</td><td>9,5</td><td>11</td><td>13</td><td>1,25</td><td>96</td><td>38</td></tr>
<tr><td>26</td><td>20</td><td colspan="2">4,1</td><td>4,45</td><td>4,85</td><td>5,5</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td colspan="2">9,0</td><td>10,5</td><td>12</td><td>14</td><td>16,5</td><td>1,6</td><td>75</td><td>38</td></tr>
<tr><td>27</td><td>30</td><td colspan="2">6,5</td><td>7,0</td><td>7,5</td><td>8,0</td><td>9,0</td><td>9,5</td><td>11</td><td>12,5</td><td colspan="2">14</td><td>16,5</td><td>19</td><td>21,5</td><td>25,5</td><td>2,4</td><td>48</td><td>30</td></tr>
<tr><td colspan="5">Индекс</td><td colspan="2">а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="24">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6" rowspan="5">Твердости чугуна и продолжительности обработки</td><td colspan="18">Твердость НВ, ГПа до 2,15 свыше 2,15</td></tr>
<tr><td colspan="15">Продолжительность обработки, мин. - до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td colspan="15"></td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td colspan="9">Коэффициент</td><td colspan="6">1,0 1,1</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="7%"><col width="7%"><col width="7%"><col width="2%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="2%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="18">Неполное штучное время Отрезка и прорезка канавок, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="18" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="6">Фрезы отрезные из стали Р6М5</td></tr>
<tr><td colspan="6">Карта 75</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="17">Длина прохода l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td colspan="2">50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td colspan="2">400</td><td colspan="2">500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="2">63 -- 80</td><td rowspan="2">2</td><td>10</td><td colspan="2">1,25</td><td>1,4</td><td>1,6</td><td>1,9</td><td>2,0</td><td>2,2</td><td>2,4</td><td>2,7</td><td colspan="2">3,1</td><td colspan="2">3,5</td><td>4,1</td><td>4,7</td><td>5,5</td><td>0,55</td><td>240</td><td>240</td><td rowspan="18"></td></tr>
<tr><td>2</td><td>15</td><td colspan="2">1,4</td><td>1,5</td><td>1,8</td><td>2,1</td><td>2,3</td><td>2,4</td><td>2,7</td><td>3,1</td><td colspan="2">3,6</td><td colspan="2">4,1</td><td>4,7</td><td>5,5</td><td>6,5</td><td>0,7</td><td>190</td><td>240</td></tr>
<tr><td>3</td><td rowspan="2">80 -- 80</td><td rowspan="2">3</td><td>10</td><td colspan="2">1,3</td><td>1,4</td><td>1,7</td><td>1,9</td><td>2,1</td><td>2,2</td><td>2,4</td><td>2,8</td><td colspan="2">3,2</td><td colspan="2">3,6</td><td>4,2</td><td>4,7</td><td>5,5</td><td>0,55</td><td>240</td><td>150</td></tr>
<tr><td>4</td><td>15</td><td colspan="2">1,5</td><td>1,7</td><td>2,1</td><td>2,3</td><td>2,5</td><td>2,8</td><td>3,2</td><td>3,7</td><td colspan="2">4,2</td><td colspan="2">5,0</td><td>5,5</td><td>6,5</td><td>8,0</td><td>0,85</td><td>150</td><td>150</td></tr>
<tr><td>5</td><td rowspan="2">100 --- 80</td><td rowspan="2">5</td><td>20</td><td colspan="2">1,6</td><td>1,7</td><td>1,9</td><td>2,2</td><td>2,3</td><td>2,5</td><td>2,8</td><td>3,3</td><td colspan="2">3,7</td><td colspan="2">4,3</td><td>5,0</td><td>5,5</td><td>6,5</td><td>0,68</td><td>190</td><td>120</td></tr>
<tr><td>6</td><td>30</td><td colspan="2">1,8</td><td>2,0</td><td>2,4</td><td>2,7</td><td>3,0</td><td>3,3</td><td>3,7</td><td>4,4</td><td colspan="2">5,0</td><td colspan="2">6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>1,0</td><td>120</td><td>96</td></tr>
<tr><td>7</td><td rowspan="2">125 --- 100</td><td rowspan="2">5</td><td>20</td><td colspan="2">1,5</td><td>1,6</td><td>1,9</td><td>2,1</td><td>2,2</td><td>2,4</td><td>2,6</td><td>3,0</td><td colspan="2">3,5</td><td colspan="2">4,1</td><td>4,8</td><td>5,2</td><td>6,5</td><td>0,7</td><td>190</td><td>75</td></tr>
<tr><td>8</td><td>30</td><td colspan="2">1,7</td><td>1,9</td><td>2,2</td><td>2,5</td><td>2,8</td><td>3,1</td><td>3,5</td><td>4,2</td><td colspan="2">4,7</td><td colspan="2">6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>1,0</td><td>120</td><td>60</td></tr>
<tr><td>9</td><td rowspan="3">160 --- 100</td><td rowspan="3">6</td><td>20</td><td colspan="2">1,7</td><td>1,8</td><td>2,2</td><td>2,5</td><td>2,7</td><td>3,0</td><td>3,3</td><td>3,8</td><td colspan="2">4,4</td><td colspan="2">5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>0,85</td><td>150</td><td>48</td></tr>
<tr><td>10</td><td>30</td><td colspan="2">2,2</td><td>2,5</td><td>2,9</td><td>3,3</td><td>3,6</td><td>4,0</td><td>4,7</td><td>5,5</td><td colspan="2">6,0</td><td colspan="2">7,0</td><td>8,5</td><td>10</td><td>12</td><td>1,25</td><td>96</td><td>48</td></tr>
<tr><td>11</td><td>45</td><td colspan="2">3,1</td><td>3,5</td><td>4,2</td><td>4,7</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td colspan="2">9,0</td><td colspan="2">11</td><td>13</td><td>15</td><td>18</td><td>1,9</td><td>60</td><td>48</td></tr>
<tr><td>12</td><td rowspan="4">200 --- 128</td><td rowspan="4">6</td><td>20</td><td colspan="2">1,6</td><td>1,8</td><td>2,0</td><td>2,2</td><td>2,5</td><td>2,8</td><td>3,1</td><td>3,5</td><td colspan="2">4,2</td><td colspan="2">4,7</td><td>5,5</td><td>6,5</td><td>7,5</td><td>0,85</td><td>150</td><td>38</td></tr>
<tr><td>13</td><td>30</td><td colspan="2">2,1</td><td>2,3</td><td>2,6</td><td>3,0</td><td>3,3</td><td>3,6</td><td>4,0</td><td>4,7</td><td colspan="2">5,3</td><td colspan="2">6,0</td><td>7,5</td><td>8,5</td><td>10</td><td>1,0</td><td>120</td><td>30</td></tr>
<tr><td>14</td><td>45</td><td colspan="2">2,5</td><td>2,7</td><td>3,2</td><td>3,6</td><td>3,8</td><td>4,3</td><td>4,8</td><td>5,5</td><td colspan="2">6,5</td><td colspan="2">7,5</td><td>8,5</td><td>10</td><td>12</td><td>1,25</td><td>96</td><td>30</td></tr>
<tr><td>15</td><td>75</td><td colspan="2">3,5</td><td>4,0</td><td>4,6</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td colspan="2">9,5</td><td colspan="2">11</td><td>13</td><td>15,5</td><td>18,5</td><td>1,9</td><td>60</td><td>30</td></tr>
<tr><td>16</td><td rowspan="3">250 --- 128</td><td rowspan="3">6</td><td>50</td><td colspan="2">3,6</td><td>4,0</td><td>4,7</td><td>5,3</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,5</td><td colspan="2">9,5</td><td colspan="2">11,5</td><td>13,5</td><td>15,5</td><td>19</td><td>1,9</td><td>60</td><td>30</td></tr>
<tr><td>17</td><td>75</td><td colspan="2">4,5</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td colspan="2">12</td><td colspan="2">14</td><td>16</td><td>19</td><td>23</td><td>2,35</td><td>48</td><td>24</td></tr>
<tr><td>18</td><td>100</td><td colspan="2">6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td>8,5</td><td>9,5</td><td>11</td><td>12,5</td><td colspan="2">15</td><td colspan="2">17,5</td><td>20</td><td>24</td><td>29</td><td>2,95</td><td>38</td><td>24</td></tr>
<tr><td colspan="4">Индекс</td><td colspan="2">а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="2">и</td><td colspan="2">к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="24">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="5" rowspan="5">Твердости чугуна и продолжительности обработки</td><td colspan="9">Твердость чугуна НВ, ГПа</td><td colspan="10">до 2,15 свыше 2,15</td></tr>
<tr><td colspan="9">Продолжительность обработки, мин.</td><td colspan="10">- до 10 свыше 10</td></tr>
<tr><td colspan="9" rowspan="3">Коэффициент</td><td colspan="10"></td></tr>
<tr><td colspan="2">1,0</td><td colspan="8">1,1 1,25</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="14">Неполное штучное время Фрезерование плоскостей и уступов, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="14">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="8">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="14">Единичное и мелкосерийное производство</td><td colspan="4">Карта 76</td><td colspan="4">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="22">7,5 - 10</td><td rowspan="4">80 -- 10</td><td rowspan="2">6</td><td>12</td><td>1,4</td><td>1,6</td><td>1,85</td><td>2,3</td><td>2,5</td><td>2,85</td><td>3,3</td><td>4,0</td><td>4,7</td><td>5,5</td><td>6,5</td><td>8,0</td><td>9,5</td><td>1,0</td><td>120</td><td>120</td><td rowspan="22">Не свыше 2,0</td></tr>
<tr><td>2</td><td>18</td><td>1,6</td><td>1,9</td><td>2,2</td><td>2,7</td><td>2,95</td><td>3,4</td><td>3,95</td><td>4,75</td><td>5,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,5</td><td>1,25</td><td>96</td><td>96</td></tr>
<tr><td>3</td><td rowspan="2">18</td><td>5</td><td>1,3</td><td>1,55</td><td>1,75</td><td>2,2</td><td>2,45</td><td>2,8</td><td>3,25</td><td>3,9</td><td>4,6</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,5</td><td>1,0</td><td>120</td><td>120</td></tr>
<tr><td>4</td><td>12</td><td>1,55</td><td>1,85</td><td>2,1</td><td>2,6</td><td>2,9</td><td>3,35</td><td>3,9</td><td>4,7</td><td>5,5</td><td>6,5</td><td>8,0</td><td>9,5</td><td>11,5</td><td>1,25</td><td>96</td><td>96</td></tr>
<tr><td>5</td><td rowspan="4">100 --- 10</td><td rowspan="2">6</td><td>18</td><td>1,95</td><td>2,3</td><td>2,65</td><td>3,25</td><td>3,6</td><td>4,15</td><td>4,9</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,0</td><td>12,0</td><td>14,5</td><td>1,6</td><td>75</td><td>75</td></tr>
<tr><td>6</td><td>27</td><td>2,35</td><td>2,8</td><td>3,25</td><td>3,9</td><td>4,35</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,5</td><td>12,0</td><td>14,5</td><td>17,5</td><td>1,95</td><td>60</td><td>60</td></tr>
<tr><td>7</td><td rowspan="2">18</td><td>5</td><td>1,5</td><td>1,75</td><td>2,05</td><td>2,55</td><td>2,85</td><td>3,25</td><td>3,85</td><td>4,65</td><td>5,5</td><td>6,5</td><td>8,0</td><td>9,5</td><td>11,5</td><td>1,25</td><td>96</td><td>96</td></tr>
<tr><td>8</td><td>12</td><td>1,8</td><td>2,2</td><td>2,55</td><td>3,15</td><td>3,5</td><td>4,05</td><td>4,8</td><td>5,5</td><td>7,0</td><td>8,5</td><td>10,0</td><td>11,5</td><td>14,0</td><td>1,6</td><td>75</td><td>75</td></tr>
<tr><td>9</td><td rowspan="4">125 --- 10</td><td rowspan="2">8</td><td>18</td><td>2,3</td><td>2,75</td><td>3,2</td><td>3,9</td><td>4,35</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,5</td><td>12,0</td><td>14,5</td><td>17,5</td><td>1,95</td><td>60</td><td>60</td></tr>
<tr><td>10</td><td>27</td><td>2,45</td><td>2,95</td><td>3,4</td><td>4,05</td><td>4,5</td><td>5,0</td><td>6,0</td><td>7,5</td><td>8,5</td><td>10,5</td><td>12,5</td><td>14,5</td><td>18,0</td><td>1,95</td><td>60</td><td>60</td></tr>
<tr><td>11</td><td rowspan="2">27</td><td>5</td><td>1,7</td><td>2,1</td><td>2,45</td><td>3,05</td><td>3,4</td><td>3,95</td><td>4,7</td><td>5,5</td><td>6,5</td><td>8,0</td><td>10,0</td><td>11,5</td><td>14,0</td><td>1,6</td><td>75</td><td>75</td></tr>
<tr><td>12</td><td>12</td><td>2,2</td><td>2,65</td><td>3,1</td><td>3,75</td><td>4,2</td><td>4,9</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,0</td><td>12,0</td><td>14,5</td><td>17,5</td><td>1,95</td><td>60</td><td>60</td></tr>
<tr><td>13</td><td rowspan="5">160 --- 60</td><td rowspan="3">8</td><td>18</td><td>2,1</td><td>2,45</td><td>2,85</td><td>3,4</td><td>3,8</td><td>4,35</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,0</td><td>12,0</td><td>14,5</td><td>1,6</td><td>75</td><td>48</td></tr>
<tr><td>14</td><td>27</td><td>2,65</td><td>3,1</td><td>3,55</td><td>4,2</td><td>4,7</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,5</td><td>12,5</td><td>15,0</td><td>18,0</td><td>1,95</td><td>60</td><td>38</td></tr>
<tr><td>15</td><td>40</td><td>2,8</td><td>3,25</td><td>3,7</td><td>4,35</td><td>4,8</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>11,0</td><td>12,5</td><td>15,0</td><td>18,0</td><td>1,95</td><td>60</td><td>38</td></tr>
<tr><td>16</td><td rowspan="2">40</td><td>5</td><td>1,55</td><td>1,85</td><td>2,1</td><td>2,6</td><td>2,9</td><td>3,35</td><td>3,9</td><td>4,7</td><td>5,5</td><td>6,5</td><td>8,0</td><td>9,5</td><td>11,5</td><td>1,25</td><td>96</td><td>60</td></tr>
<tr><td>17</td><td>12</td><td>2,0</td><td>2,35</td><td>2,7</td><td>3,3</td><td>3,65</td><td>4,2</td><td>4,95</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,0</td><td>12,0</td><td>14,5</td><td>1,6</td><td>75</td><td>48</td></tr>
<tr><td>18</td><td rowspan="5">200 --- 16</td><td rowspan="3">12</td><td>27</td><td>2,8</td><td>3,25</td><td>3,75</td><td>4,4</td><td>4,9</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>11,0</td><td>13,0</td><td>15,0</td><td>18,5</td><td>1,95</td><td>60</td><td>38</td></tr>
<tr><td>19</td><td>40</td><td>3,55</td><td>4,15</td><td>4,7</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,0</td><td>13,5</td><td>16,0</td><td>19,0</td><td>22,5</td><td>2,4</td><td>48</td><td>30</td></tr>
<tr><td>20</td><td>60</td><td>3,85</td><td>4,4</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,5</td><td>9,5</td><td>11,5</td><td>13,5</td><td>16,0</td><td>19,0</td><td>23,0</td><td>2,4</td><td>48</td><td>30</td></tr>
<tr><td>21</td><td rowspan="2">40</td><td>5</td><td>1,85</td><td>2,2</td><td>2,55</td><td>3,15</td><td>3,5</td><td>4,0</td><td>4,8</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,0</td><td>11,5</td><td>14,5</td><td>1,6</td><td>75</td><td>48</td></tr>
<tr><td>22</td><td>12</td><td>2,4</td><td>2,85</td><td>3,35</td><td>4,0</td><td>4,5</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,5</td><td>12,5</td><td>14,5</td><td>18,0</td><td>1,95</td><td>60</td><td>38</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="2%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="19">Неполное штучное время Фрезерование плоскостей и уступов, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="9">Горизонтально-расточные станки</td></tr>
<tr><td colspan="19">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="9">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="19">Единичное и мелкосерийное производство</td><td colspan="5">Карта 76</td><td colspan="4">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="20">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td colspan="2">50</td><td colspan="2">75</td><td>100</td><td colspan="2">125</td><td>150</td><td colspan="2">200</td><td>250</td><td>300</td><td colspan="2">400</td><td>500</td><td>600</td><td colspan="2">750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="20">Время на проход, мин.</td></tr>
<tr><td>23</td><td rowspan="10">7,5 - 10</td><td rowspan="5">250 --- 20</td><td rowspan="3">12</td><td>27</td><td colspan="2">3,5</td><td colspan="2">4,1</td><td>4,7</td><td colspan="2">5,5</td><td>6,0</td><td colspan="2">7,0</td><td>8,0</td><td>9,5</td><td colspan="2">11,0</td><td>13,5</td><td>16,0</td><td colspan="2">18,5</td><td>22,5</td><td>2,4</td><td>48</td><td>24</td><td rowspan="10">Не свыше 2,0</td></tr>
<tr><td>24</td><td>40</td><td colspan="2">3,8</td><td colspan="2">4,4</td><td>5,0</td><td colspan="2">5,5</td><td>6,5</td><td colspan="2">7,0</td><td>8,5</td><td>9,5</td><td colspan="2">11,5</td><td>13,5</td><td>16,0</td><td colspan="2">19,0</td><td>23,0</td><td>2,4</td><td>48</td><td>24</td></tr>
<tr><td>25</td><td>60</td><td colspan="2">5,0</td><td colspan="2">6,0</td><td>6,5</td><td colspan="2">7,5</td><td>8,0</td><td colspan="2">9,5</td><td>10,5</td><td>12,5</td><td colspan="2">14,5</td><td>17,5</td><td>20,5</td><td colspan="2">24,0</td><td>29,0</td><td>3,05</td><td>38</td><td>19</td></tr>
<tr><td>26</td><td rowspan="2">40</td><td>5</td><td colspan="2">2,15</td><td colspan="2">2,65</td><td>3,1</td><td colspan="2">3,75</td><td>4,25</td><td colspan="2">5,0</td><td>6,0</td><td>7,0</td><td colspan="2">8,5</td><td>10,0</td><td>12,0</td><td colspan="2">14,5</td><td>17,5</td><td>1,95</td><td>60</td><td>30</td></tr>
<tr><td>27</td><td>12</td><td colspan="2">2,95</td><td colspan="2">3,55</td><td>4,1</td><td colspan="2">4,9</td><td>5,5</td><td colspan="2">6,5</td><td>7,5</td><td>9,0</td><td colspan="2">10,5</td><td>13,0</td><td>15,5</td><td colspan="2">18,0</td><td>22,0</td><td>2,4</td><td>48</td><td>24</td></tr>
<tr><td>28</td><td rowspan="5">315 --- 22</td><td rowspan="3">12</td><td>27</td><td colspan="2">4,45</td><td colspan="2">5,0</td><td>6,0</td><td colspan="2">7,0</td><td>7,5</td><td colspan="2">8,5</td><td>10,0</td><td>12,0</td><td colspan="2">14,0</td><td>17,0</td><td>20,0</td><td colspan="2">23,5</td><td>28,5</td><td>3,05</td><td>38</td><td>19</td></tr>
<tr><td>29</td><td>40</td><td colspan="2">5,0</td><td colspan="2">6,0</td><td>7,0</td><td colspan="2">7,5</td><td>8,0</td><td colspan="2">9,0</td><td>10,5</td><td>12,5</td><td colspan="2">14,5</td><td>17,5</td><td>20,5</td><td colspan="2">24,0</td><td>29,0</td><td>3,05</td><td>38</td><td>19</td></tr>
<tr><td>30</td><td>60</td><td colspan="2">7,0</td><td colspan="2">8,0</td><td>8,5</td><td colspan="2">10,0</td><td>11,0</td><td colspan="2">12,0</td><td>14,0</td><td>16,0</td><td colspan="2">19,0</td><td>22,5</td><td>26,5</td><td colspan="2">31,0</td><td>37,5</td><td>3,8</td><td>30</td><td>15</td></tr>
<tr><td>31</td><td rowspan="2">40</td><td>5</td><td colspan="2">2,65</td><td colspan="2">3,25</td><td>3,8</td><td colspan="2">4,6</td><td>5,0</td><td colspan="2">6,0</td><td>7,0</td><td>8,5</td><td colspan="2">10,5</td><td>12,5</td><td>15,0</td><td colspan="2">18,0</td><td>22,0</td><td>2,4</td><td>48</td><td>24</td></tr>
<tr><td>32</td><td>12</td><td colspan="2">3,75</td><td colspan="2">4,45</td><td>5,0</td><td colspan="2">6,0</td><td>7,0</td><td colspan="2">8,0</td><td>9,5</td><td>11,0</td><td colspan="2">13,0</td><td>16,0</td><td>19,0</td><td colspan="2">22,5</td><td>28,0</td><td>3,05</td><td>38</td><td>19</td></tr>
<tr><td colspan="5">Индекс</td><td colspan="2">а</td><td colspan="2">б</td><td>в</td><td colspan="2">г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td colspan="2">м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="28">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="18">Группы Группа стали Углеродистые, хромистые, никелевые обрабатываемой хромоникелевые</td><td colspan="10">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="14">прочности и Предел прочности до 0,59 0,59 - 0,74 продолжительности сигма , ГПа обработки в</td><td colspan="4">свыше 0,74</td><td colspan="4">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="8">Продолжительность до 10 обработки, мин.</td><td colspan="6">свыше 10 -</td><td colspan="4">до 10 свыше 10</td><td colspan="4">до 10 свыше 10</td><td colspan="3">до 10 свыше 10</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="8" rowspan="3">Коэффициент 0,9</td><td colspan="6"></td><td colspan="4" rowspan="3">1,1 1,25</td><td colspan="4" rowspan="3">1,0 1,1</td><td colspan="3" rowspan="3">1,1 1,2</td><td colspan="3" rowspan="3">1,2 1,35</td></tr>
<tr><td colspan="3">0,8</td><td colspan="3">1,0</td></tr>
<tr><td colspan="6"></td></tr>
<tr><td colspan="14">Состояние Состояние без корки и удара обрабатываемой обрабатываемой поверхности поверхности</td><td colspan="14">по корке и на удар</td></tr>
<tr><td colspan="14"></td><td colspan="14" rowspan="3">1,2</td></tr>
<tr><td colspan="6">Коэффициент</td><td colspan="8">1,0</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="16">Неполное штучное время Фрезерование плоскостей и уступов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Единичное и мелкосерийное производство</td><td colspan="6">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 77</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="14">7,5 - 10</td><td>80 -- 10</td><td rowspan="14">2</td><td>18</td><td>2,2</td><td>2,45</td><td>2,65</td><td>3,0</td><td>3,25</td><td>3,55</td><td>4,0</td><td>4,8</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>1,0</td><td>120</td><td>120</td><td rowspan="14">Не свыше 1,0</td></tr>
<tr><td>2</td><td rowspan="2">100 --- 10</td><td>18</td><td>2,6</td><td>2,9</td><td>3,15</td><td>3,55</td><td>3,85</td><td>4,25</td><td>4,85</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,5</td><td>12,5</td><td>1,25</td><td>96</td><td>96</td></tr>
<tr><td>3</td><td>27</td><td>3,15</td><td>3,5</td><td>3,9</td><td>4,35</td><td>4,7</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,0</td><td>13,0</td><td>15,5</td><td>1,6</td><td>75</td><td>75</td></tr>
<tr><td>4</td><td rowspan="2">125 --- 10</td><td>18</td><td>3,1</td><td>3,5</td><td>3,85</td><td>4,35</td><td>4,7</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,0</td><td>13,0</td><td>15,5</td><td>1,6</td><td>75</td><td>75</td></tr>
<tr><td>5</td><td>27</td><td>3,95</td><td>4,4</td><td>4,25</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,0</td><td>19,5</td><td>1,95</td><td>60</td><td>60</td></tr>
<tr><td>6</td><td rowspan="3">160 --- 10</td><td>18</td><td>3,35</td><td>3,7</td><td>4,05</td><td>4,55</td><td>4,9</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,0</td><td>15,5</td><td>1,6</td><td>75</td><td>60</td></tr>
<tr><td>7</td><td>27</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,0</td><td>12,5</td><td>15,0</td><td>17,5</td><td>20,0</td><td>24,0</td><td>2,4</td><td>48</td><td>48</td></tr>
<tr><td>8</td><td>40</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td>8,5</td><td>10,0</td><td>11,5</td><td>13,0</td><td>15,5</td><td>17,5</td><td>20,5</td><td>24,5</td><td>2,4</td><td>48</td><td>48</td></tr>
<tr><td>9</td><td rowspan="3">200 --- 16</td><td>27</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,0</td><td>9,0</td><td>10,0</td><td>11,5</td><td>13,0</td><td>15,5</td><td>18,0</td><td>20,5</td><td>24,5</td><td>2,4</td><td>48</td><td>48</td></tr>
<tr><td>10</td><td>40</td><td>7,0</td><td>8,0</td><td>8,5</td><td>9,5</td><td>10,0</td><td>11,0</td><td>12,5</td><td>14,5</td><td>16,5</td><td>19,5</td><td>22,5</td><td>26,0</td><td>31,0</td><td>3,05</td><td>38</td><td>38</td></tr>
<tr><td>11</td><td>60</td><td>8,0</td><td>8,5</td><td>9,5</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,5</td><td>15,0</td><td>17,5</td><td>20,0</td><td>23,0</td><td>27,0</td><td>32,0</td><td>3,05</td><td>38</td><td>38</td></tr>
<tr><td>12</td><td rowspan="3">250 --- 20</td><td>27</td><td>6,0</td><td>6,5</td><td>7,0</td><td>7,5</td><td>8,5</td><td>9,0</td><td>10,5</td><td>12,0</td><td>13,5</td><td>16,0</td><td>18,0</td><td>21,0</td><td>25,0</td><td>2,4</td><td>48</td><td>38</td></tr>
<tr><td>13</td><td>40</td><td>8,0</td><td>8,5</td><td>9,5</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,5</td><td>15,0</td><td>17,5</td><td>20,0</td><td>23,0</td><td>27,0</td><td>32,0</td><td>3,05</td><td>38</td><td>30</td></tr>
<tr><td>14</td><td>60</td><td>8,5</td><td>9,5</td><td>10,0</td><td>11,0</td><td>11,5</td><td>13,0</td><td>14,5</td><td>16,0</td><td>18,0</td><td>21,0</td><td>24,0</td><td>28,0</td><td>33,0</td><td>3,05</td><td>38</td><td>30</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="5%"><col width="2%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="19">Неполное штучное время Фрезерование плоскостей и уступов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="19" rowspan="2">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Единичное и мелкосерийное производство</td><td colspan="7">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 77</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td colspan="2">Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="17">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td colspan="2" rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td colspan="2">200</td><td>250</td><td>300</td><td colspan="2">400</td><td>500</td><td>600</td><td colspan="2">750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="17">Время на проход, мин.</td></tr>
<tr><td>15</td><td rowspan="3">7,5 - 10</td><td colspan="2" rowspan="3">315 --- 22</td><td rowspan="3">2</td><td>27</td><td>7,5</td><td>8,0</td><td>9,0</td><td>10,0</td><td>10,5</td><td colspan="2">11,5</td><td>13,0</td><td>15,0</td><td colspan="2">17,6</td><td>20,0</td><td>23,0</td><td colspan="2">26,5</td><td>31,5</td><td>3,05</td><td>38</td><td>30</td><td rowspan="3">Не свыше 1,0</td></tr>
<tr><td>16</td><td>40</td><td>10,5</td><td>11,5</td><td>12,5</td><td>13,5</td><td>14,5</td><td colspan="2">16,0</td><td>17,5</td><td>20,0</td><td colspan="2">22,5</td><td>26,0</td><td>30,0</td><td colspan="2">34,5</td><td>41,0</td><td>3,8</td><td>30</td><td>24</td></tr>
<tr><td>17</td><td>60</td><td>12,0</td><td>13,0</td><td>14,0</td><td>15,0</td><td>16,0</td><td colspan="2">17,5</td><td>19,0</td><td>21,5</td><td colspan="2">24,0</td><td>27,5</td><td>31,5</td><td colspan="2">36,0</td><td>42,5</td><td>3,8</td><td>30</td><td>24</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td colspan="2">м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="26">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3">Группы обрабатываемой стали и предела</td><td colspan="3">Группа стали</td><td colspan="10">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="10">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3" rowspan="5">прочности</td><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="3">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="4">свыше 0,74</td><td colspan="4">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="3">Продолжительность обработки, мин.</td><td colspan="3">до 10 свыше 10</td><td colspan="3">-</td><td colspan="4">до 10 свыше 10</td><td colspan="4">до 10 свыше 10</td><td colspan="3">до 10 свыше 10</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="3" rowspan="3">0,9 0,8</td><td colspan="3"></td><td colspan="4" rowspan="3">1,1 1,25</td><td colspan="4" rowspan="3">1,0 1,1</td><td colspan="3" rowspan="3">1,1 1,2</td><td colspan="3" rowspan="3">1,2 1,35</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="16">Неполное штучное время Фрезерование пазов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Единичное и мелкосерийное производство</td><td colspan="6">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 78</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="19">7,5 - 10</td><td rowspan="3">80 -- 10</td><td rowspan="3">25</td><td>5</td><td>1,8</td><td>2,0</td><td>2,15</td><td>2,45</td><td>2,65</td><td>2,9</td><td>3,3</td><td>3,95</td><td>4,5</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,5</td><td>0,85</td><td>150</td><td>150</td><td rowspan="19">Не свыше 3,0</td></tr>
<tr><td>2</td><td>10</td><td>2,3</td><td>2,6</td><td>2,85</td><td>3,25</td><td>3,53</td><td>3,95</td><td>4,55</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>12,0</td><td>1,25</td><td>96</td><td>120</td></tr>
<tr><td>3</td><td>15</td><td>2,75</td><td>3,1</td><td>3,45</td><td>3,95</td><td>4,3</td><td>4,85</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>11,0</td><td>12,5</td><td>15,0</td><td>1,6</td><td>75</td><td>120</td></tr>
<tr><td>4</td><td rowspan="4">100 --- 10</td><td rowspan="4">28</td><td>5</td><td>2,0</td><td>2,25</td><td>2,45</td><td>2,8</td><td>3,0</td><td>3,35</td><td>3,8</td><td>4,6</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,5</td><td>10,0</td><td>1,0</td><td>120</td><td>130</td></tr>
<tr><td>5</td><td>10</td><td>2,7</td><td>3,1</td><td>3,45</td><td>3,9</td><td>4,3</td><td>4,85</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,5</td><td>12,5</td><td>15,0</td><td>1,6</td><td>75</td><td>96</td></tr>
<tr><td>6</td><td>15</td><td>3,3</td><td>3,75</td><td>4,2</td><td>4,8</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,5</td><td>13,0</td><td>15,5</td><td>18,5</td><td>1,95</td><td>60</td><td>96</td></tr>
<tr><td>7</td><td>20</td><td>4,0</td><td>4,6</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>11,5</td><td>14,0</td><td>16,5</td><td>19,0</td><td>23,0</td><td>2,4</td><td>48</td><td>96</td></tr>
<tr><td>8</td><td rowspan="4">125 --- 10</td><td rowspan="4">32</td><td>5</td><td>2,25</td><td>2,55</td><td>2,85</td><td>3,25</td><td>3,5</td><td>3,95</td><td>4,5</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>10,0</td><td>12,0</td><td>1,25</td><td>96</td><td>96</td></tr>
<tr><td>9</td><td>10</td><td>3,3</td><td>3,75</td><td>4,2</td><td>4,75</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,0</td><td>13,0</td><td>15,5</td><td>18,5</td><td>1,95</td><td>60</td><td>75</td></tr>
<tr><td>10</td><td>15</td><td>4,8</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,0</td><td>15,5</td><td>17,0</td><td>20,0</td><td>23,5</td><td>29,0</td><td>3,05</td><td>38</td><td>75</td></tr>
<tr><td>11</td><td>20</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,0</td><td>11,5</td><td>13,0</td><td>14,5</td><td>18,0</td><td>21,5</td><td>25,5</td><td>30,0</td><td>36,5</td><td>3,8</td><td>30</td><td>75</td></tr>
<tr><td>12</td><td rowspan="4">160 --- 16</td><td rowspan="4">36</td><td>10</td><td>2,6</td><td>2,9</td><td>3,15</td><td>3,55</td><td>3,85</td><td>4,25</td><td>4,85</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,5</td><td>12,5</td><td>1,25</td><td>96</td><td>75</td></tr>
<tr><td>13</td><td>15</td><td>3,2</td><td>3,6</td><td>3,95</td><td>4,4</td><td>4,8</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,0</td><td>13,0</td><td>15,5</td><td>13</td><td>75</td><td>60</td></tr>
<tr><td>14</td><td>20</td><td>4,65</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>12,5</td><td>14,5</td><td>17,0</td><td>20,0</td><td>23,5</td><td>2,4</td><td>48</td><td>60</td></tr>
<tr><td>15</td><td>30</td><td>7,5</td><td>8,5</td><td>9,0</td><td>10,0</td><td>11,0</td><td>12,5</td><td>14,5</td><td>16,5</td><td>19,0</td><td>23,0</td><td>26,5</td><td>31,0</td><td>37,5</td><td>3,8</td><td>30</td><td>48</td></tr>
<tr><td>16</td><td rowspan="4">200 --- 16</td><td rowspan="4">40</td><td>10</td><td>3,15</td><td>3,55</td><td>3,9</td><td>4,4</td><td>4,75</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,0</td><td>13,0</td><td>15,5</td><td>1,6</td><td>75</td><td>48</td></tr>
<tr><td>17</td><td>15</td><td>4,0</td><td>4,45</td><td>4,9</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,0</td><td>12,0</td><td>14,0</td><td>16,0</td><td>19,5</td><td>1,95</td><td>60</td><td>48</td></tr>
<tr><td>18</td><td>20</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,0</td><td>10,0</td><td>11,5</td><td>13,5</td><td>15,5</td><td>18,5</td><td>21,5</td><td>25,0</td><td>30,0</td><td>3,05</td><td>38</td><td>48</td></tr>
<tr><td>19</td><td>30</td><td>8,0</td><td>9,0</td><td>10,0</td><td>11,0</td><td>12,0</td><td>13,5</td><td>15,0</td><td>17,5</td><td>20,0</td><td>23,5</td><td>27,5</td><td>32,0</td><td>38,5</td><td>3,8</td><td>30</td><td>48</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="4%"><col width="2%"><col width="2%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="20">Неполное штучное время Фрезерование пазов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="20" rowspan="2">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Единичное и мелкосерийное производство</td><td colspan="7">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 78</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="19">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td colspan="2">75</td><td>100</td><td colspan="2">125</td><td>150</td><td colspan="2">200</td><td>250</td><td>300</td><td colspan="2">400</td><td>500</td><td>600</td><td colspan="2">750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="19">Время на проход, мин.</td></tr>
<tr><td>20</td><td rowspan="8">7,5 - 10</td><td rowspan="4">250 --- 20</td><td rowspan="4">45</td><td>10</td><td>3,3</td><td colspan="2">3,7</td><td>4,05</td><td colspan="2">4,5</td><td>4,9</td><td colspan="2">5,5</td><td>6,0</td><td>7,0</td><td colspan="2">8,5</td><td>10,0</td><td>11,5</td><td colspan="2">13,0</td><td>16,0</td><td>1,6</td><td>75</td><td>38</td><td rowspan="8">Не свыше 3,0</td></tr>
<tr><td>21</td><td>15</td><td>4,2</td><td colspan="2">4,65</td><td>5,0</td><td colspan="2">5,5</td><td>6,0</td><td colspan="2">7,0</td><td>8,0</td><td>9,0</td><td colspan="2">10,5</td><td>12,0</td><td>14,0</td><td colspan="2">16,5</td><td>19,5</td><td>1,95</td><td>60</td><td>38</td></tr>
<tr><td>22</td><td>20</td><td>6,5</td><td colspan="2">7,0</td><td>8,0</td><td colspan="2">8,5</td><td>9,5</td><td colspan="2">10,5</td><td>12,0</td><td>14,0</td><td colspan="2">16,0</td><td>19,0</td><td>22,0</td><td colspan="2">25,5</td><td>30,5</td><td>3,05</td><td>38</td><td>38</td></tr>
<tr><td>23</td><td>30</td><td>10,5</td><td colspan="2">12,0</td><td>13,0</td><td colspan="2">14,5</td><td>15,5</td><td colspan="2">17,0</td><td>19,5</td><td>22,0</td><td colspan="2">25,5</td><td>30,0</td><td>35,0</td><td colspan="2">40,5</td><td>48,5</td><td>4,7</td><td>24</td><td>30</td></tr>
<tr><td>24</td><td rowspan="4">315 --- 22</td><td rowspan="4">50</td><td>10</td><td>4,1</td><td colspan="2">4,55</td><td>5,0</td><td colspan="2">5,5</td><td>6,0</td><td colspan="2">6,5</td><td>7,5</td><td>9,0</td><td colspan="2">10,5</td><td>12,0</td><td>14,0</td><td colspan="2">16,5</td><td>19,5</td><td>1,95</td><td>60</td><td>30</td></tr>
<tr><td>25</td><td>15</td><td>5,5</td><td colspan="2">6,0</td><td>6,5</td><td colspan="2">7,0</td><td>7,5</td><td colspan="2">8,5</td><td>9,5</td><td>11,0</td><td colspan="2">13,0</td><td>15,0</td><td>17,5</td><td colspan="2">20,5</td><td>24,5</td><td>2,4</td><td>48</td><td>30</td></tr>
<tr><td>26</td><td>20</td><td>8,5</td><td colspan="2">9,5</td><td>10,5</td><td colspan="2">11,5</td><td>12,0</td><td colspan="2">13,5</td><td>15,5</td><td>17,5</td><td colspan="2">20,5</td><td>24,0</td><td>28,0</td><td colspan="2">32,5</td><td>39,0</td><td>3,8</td><td>30</td><td>30</td></tr>
<tr><td>27</td><td>30</td><td>14,5</td><td colspan="2">16,0</td><td>17,5</td><td colspan="2">19,0</td><td>20,5</td><td colspan="2">22,5</td><td>25,5</td><td>28,5</td><td colspan="2">33,0</td><td>38,5</td><td>44,5</td><td colspan="2">52,0</td><td>62,0</td><td>6,0</td><td>19</td><td>24</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td colspan="2">б</td><td>в</td><td colspan="2">г</td><td>д</td><td colspan="2">е</td><td>ж</td><td>з</td><td colspan="2">и</td><td>к</td><td>л</td><td colspan="2">м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="27">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="17">Группы Группа стали Углеродистые, хромистые, никелевые, обрабатываемой хромоникелевые</td><td colspan="10">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="13">прочности и Предел прочности до 0,59 0,59 - 0,74 продолжительности сигма , ГПа обработки в</td><td colspan="4">свыше 0,74</td><td colspan="4">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="3">свыше 0,74</td></tr>
<tr><td colspan="7">Продолжительность до 10 обработки, мин.</td><td colspan="6">свыше 10 -</td><td colspan="4">до 10 свыше 10</td><td colspan="4">до 10 свыше 10</td><td colspan="3">до 10 свыше 10</td><td colspan="3">до 10 свыше 10</td></tr>
<tr><td colspan="7" rowspan="3">Коэффициент 0,9</td><td colspan="6"></td><td colspan="4" rowspan="3">1,1 1,25</td><td colspan="4" rowspan="3">1,0 1,1</td><td colspan="3" rowspan="3">1,1 1,2</td><td colspan="3" rowspan="3">1,2 1,35</td></tr>
<tr><td colspan="3">0,8</td><td colspan="3">1,0</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="16">Неполное штучное время Фрезерование плоскостей и уступов, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа и алюминиевые Единичное и мелкосерийное производство</td><td colspan="6">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 79</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="22">7,5 - 10</td><td rowspan="4">80 -- 10</td><td rowspan="2">6</td><td>12</td><td>0,95</td><td>1,05</td><td>1,1</td><td>1,4</td><td>1,45</td><td>1,6</td><td>1,7</td><td>2,1</td><td>2,3</td><td>2,6</td><td>3,0</td><td>3,35</td><td>3,85</td><td>0,4</td><td>380</td><td>240</td><td rowspan="22">Не свыше 2,5</td></tr>
<tr><td>2</td><td>18</td><td>1,05</td><td>1,15</td><td>1,2</td><td>1,55</td><td>1,6</td><td>1,75</td><td>1,95</td><td>2,35</td><td>2,6</td><td>3,0</td><td>3,45</td><td>3,9</td><td>4,55</td><td>0,48</td><td>300</td><td>190</td></tr>
<tr><td>3</td><td rowspan="2">18</td><td>5</td><td>0,9</td><td>0,95</td><td>1,0</td><td>1,3</td><td>1,35</td><td>1,45</td><td>1,55</td><td>1,9</td><td>2,05</td><td>2,3</td><td>2,6</td><td>2,9</td><td>3,3</td><td>0,34</td><td>480</td><td>300</td></tr>
<tr><td>4</td><td>12</td><td>0,95</td><td>1,05</td><td>1,1</td><td>1,4</td><td>1,45</td><td>1,6</td><td>1,7</td><td>2,1</td><td>2,3</td><td>2,6</td><td>3,0</td><td>3,35</td><td>3,85</td><td>0,4</td><td>380</td><td>240</td></tr>
<tr><td>5</td><td rowspan="4">100 --- 10</td><td rowspan="2">6</td><td>18</td><td>1,05</td><td>1,15</td><td>1,25</td><td>1,55</td><td>1,65</td><td>1,8</td><td>1,95</td><td>2,35</td><td>2,65</td><td>3,0</td><td>3,45</td><td>3,95</td><td>4,55</td><td>0,48</td><td>300</td><td>150</td></tr>
<tr><td>6</td><td>27</td><td>1,15</td><td>1,25</td><td>1,4</td><td>1,7</td><td>1,85</td><td>2,0</td><td>2,25</td><td>2,7</td><td>3,0</td><td>3,5</td><td>4,05</td><td>4,6</td><td>5,5</td><td>0,55</td><td>240</td><td>120</td></tr>
<tr><td>7</td><td rowspan="2">18</td><td>5</td><td>0,95</td><td>1,0</td><td>1,1</td><td>1,4</td><td>1,45</td><td>1,55</td><td>1,7</td><td>2,05</td><td>2,3</td><td>2,55</td><td>2,95</td><td>3,35</td><td>3,85</td><td>0,4</td><td>380</td><td>190</td></tr>
<tr><td>8</td><td>12</td><td>1,05</td><td>1,1</td><td>1,2</td><td>1,5</td><td>1,6</td><td>1,75</td><td>1,95</td><td>2,35</td><td>2,6</td><td>2,95</td><td>3,45</td><td>3,9</td><td>4,55</td><td>0,48</td><td>300</td><td>150</td></tr>
<tr><td>9</td><td rowspan="4">125 --- 10</td><td rowspan="2">8</td><td>18</td><td>1,15</td><td>1,25</td><td>1,4</td><td>1,7</td><td>1,85</td><td>2,0</td><td>2,25</td><td>2,65</td><td>3,0</td><td>3,45</td><td>4,05</td><td>4,6</td><td>5,5</td><td>0,55</td><td>240</td><td>120</td></tr>
<tr><td>10</td><td>27</td><td>1,3</td><td>1,45</td><td>1,6</td><td>1,95</td><td>2,1</td><td>2,3</td><td>2,6</td><td>3,1</td><td>3,55</td><td>4,1</td><td>4,8</td><td>5,5</td><td>6,5</td><td>0,7</td><td>190</td><td>96</td></tr>
<tr><td>11</td><td rowspan="2">27</td><td>5</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,5</td><td>1,6</td><td>1,75</td><td>1,9</td><td>2,3</td><td>2,6</td><td>2,95</td><td>3,4</td><td>3,9</td><td>4,5</td><td>0,48</td><td>300</td><td>150</td></tr>
<tr><td>12</td><td>12</td><td>1,1</td><td>1,25</td><td>1,35</td><td>1,7</td><td>1,8</td><td>1,95</td><td>2,2</td><td>2,65</td><td>3,0</td><td>3,45</td><td>4,0</td><td>4,6</td><td>5,5</td><td>0,55</td><td>240</td><td>150</td></tr>
<tr><td>13</td><td rowspan="5">160 --- 16</td><td rowspan="2">8</td><td>18</td><td>1,2</td><td>1,3</td><td>1,4</td><td>1,75</td><td>1,85</td><td>2,05</td><td>2,25</td><td>2,7</td><td>3,05</td><td>3,5</td><td>4,05</td><td>4,65</td><td>5,5</td><td>0,55</td><td>240</td><td>96</td></tr>
<tr><td>14</td><td>27</td><td>1,25</td><td>1,35</td><td>1,45</td><td>1,8</td><td>1,9</td><td>2,1</td><td>2,3</td><td>2,75</td><td>3,1</td><td>3,55</td><td>4,1</td><td>4,7</td><td>5,5</td><td>0,55</td><td>240</td><td>75</td></tr>
<tr><td>15</td><td rowspan="3">40</td><td>40</td><td>1,4</td><td>1,55</td><td>1,7</td><td>2,05</td><td>2,2</td><td>2,4</td><td>2,7</td><td>3,2</td><td>3,65</td><td>4,2</td><td>4,9</td><td>5,5</td><td>6,5</td><td>0,7</td><td>190</td><td>60</td></tr>
<tr><td>16</td><td>5</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,5</td><td>1,6</td><td>1,75</td><td>1,9</td><td>2,3</td><td>2,6</td><td>2,95</td><td>3,45</td><td>3,9</td><td>4,55</td><td>0,48</td><td>300</td><td>120</td></tr>
<tr><td>17</td><td>12</td><td>1,05</td><td>1,15</td><td>1,25</td><td>1,55</td><td>1,65</td><td>1,8</td><td>1,95</td><td>2,4</td><td>2,65</td><td>3,0</td><td>3,5</td><td>3,95</td><td>4,6</td><td>0,48</td><td>300</td><td>96</td></tr>
<tr><td>18</td><td rowspan="5">200 --- 16</td><td rowspan="3">12</td><td>27</td><td>1,3</td><td>1,4</td><td>1,5</td><td>1,85</td><td>1,95</td><td>2,15</td><td>2,35</td><td>2,8</td><td>3,15</td><td>3,6</td><td>4,2</td><td>4,75</td><td>5,5</td><td>0,55</td><td>240</td><td>60</td></tr>
<tr><td>19</td><td>40</td><td>1,45</td><td>1,6</td><td>1,75</td><td>2,15</td><td>2,25</td><td>2,5</td><td>2,8</td><td>3,3</td><td>3,7</td><td>4,3</td><td>5,0</td><td>5,5</td><td>6,5</td><td>0,7</td><td>190</td><td>75</td></tr>
<tr><td>20</td><td>60</td><td>1,75</td><td>1,95</td><td>2,1</td><td>2,5</td><td>2,7</td><td>3,0</td><td>3,35</td><td>3,95</td><td>4,5</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,5</td><td>0,85</td><td>150</td><td>60</td></tr>
<tr><td>21</td><td rowspan="2">40</td><td>5</td><td>1,0</td><td>1,05</td><td>1,1</td><td>1,4</td><td>1,5</td><td>1,6</td><td>1,75</td><td>2,1</td><td>2,3</td><td>2,6</td><td>3,0</td><td>3,4</td><td>3,9</td><td>0,4</td><td>380</td><td>120</td></tr>
<tr><td>22</td><td>12</td><td>1,1</td><td>1,2</td><td>1,3</td><td>1,6</td><td>1,7</td><td>1,8</td><td>2,0</td><td>2,4</td><td>2,7</td><td>3,05</td><td>3,55</td><td>4,0</td><td>4,65</td><td>0,48</td><td>300</td><td>96</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="16">Неполное штучное время Фрезерование плоскостей и уступов, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа и алюминиевые Единичное и мелкосерийное производство</td><td colspan="6">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 79</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>23</td><td rowspan="10">7,5 - 10</td><td rowspan="5">250 --- 20</td><td rowspan="3">12</td><td>27</td><td>1,3</td><td>1,45</td><td>1,55</td><td>1,9</td><td>2,0</td><td>2,15</td><td>2,4</td><td>2,85</td><td>3,2</td><td>3,65</td><td>4,2</td><td>4,8</td><td>5,5</td><td>0,55</td><td>240</td><td>60</td><td rowspan="10">Не свыше 2,0</td></tr>
<tr><td>24</td><td>40</td><td>1,55</td><td>1,7</td><td>1,85</td><td>2,2</td><td>2,35</td><td>2,55</td><td>2,85</td><td>3,35</td><td>3,8</td><td>4,35</td><td>5,0</td><td>6,0</td><td>7,0</td><td>0,7</td><td>190</td><td>48</td></tr>
<tr><td>25</td><td>60</td><td>1,85</td><td>2,05</td><td>2,25</td><td>2,65</td><td>2,8</td><td>3,1</td><td>3,45</td><td>4,05</td><td>4,6</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,5</td><td>0,85</td><td>150</td><td>48</td></tr>
<tr><td>26</td><td rowspan="2">40</td><td>5</td><td>1,05</td><td>1,15</td><td>1,25</td><td>1,55</td><td>1,65</td><td>1,75</td><td>1,95</td><td>2,35</td><td>2,65</td><td>3,0</td><td>3,5</td><td>3,95</td><td>4,6</td><td>0,48</td><td>300</td><td>96</td></tr>
<tr><td>27</td><td>12</td><td>1,1</td><td>1,2</td><td>1,3</td><td>1,6</td><td>1,7</td><td>1,85</td><td>2,05</td><td>2,45</td><td>2,7</td><td>3,05</td><td>3,5</td><td>4,0</td><td>4,65</td><td>0,48</td><td>300</td><td>75</td></tr>
<tr><td>28</td><td rowspan="5">315 --- 22</td><td rowspan="3">12</td><td>27</td><td>1,5</td><td>1,65</td><td>1,8</td><td>2,15</td><td>2,3</td><td>2,5</td><td>2,8</td><td>3,3</td><td>3,75</td><td>4,35</td><td>5,0</td><td>6,0</td><td>7,0</td><td>0,7</td><td>190</td><td>48</td></tr>
<tr><td>29</td><td>40</td><td>1,85</td><td>2,05</td><td>2,2</td><td>2,6</td><td>2,8</td><td>3,1</td><td>3,45</td><td>4,05</td><td>4,6</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,5</td><td>0,85</td><td>150</td><td>38</td></tr>
<tr><td>30</td><td>60</td><td>2,0</td><td>2,2</td><td>2,35</td><td>2,75</td><td>2,95</td><td>3,25</td><td>3,6</td><td>4,2</td><td>4,75</td><td>5,5</td><td>6,5</td><td>7,0</td><td>8,5</td><td>0,85</td><td>150</td><td>38</td></tr>
<tr><td>31</td><td rowspan="2">40</td><td>5</td><td>1,05</td><td>1,15</td><td>1,25</td><td>1,55</td><td>1,65</td><td>1,8</td><td>2,0</td><td>2,4</td><td>2,65</td><td>3,0</td><td>3,5</td><td>3,95</td><td>4,6</td><td>0,48</td><td>300</td><td>75</td></tr>
<tr><td>32</td><td>12</td><td>1,25</td><td>1,35</td><td>1,45</td><td>1,8</td><td>1,9</td><td>2,1</td><td>2,3</td><td>2,75</td><td>3,1</td><td>3,55</td><td>4,15</td><td>4,7</td><td>5,5</td><td>0,55</td><td>240</td><td>60</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="22">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="17">Группы медных сплавов и твердости Группа сплавов Гомогенные</td><td colspan="5">Гетерогенные</td></tr>
<tr><td colspan="17">Твердость НВ, ГПа 0,59 - 0,74</td><td colspan="5">0,98 - 1,37 1,47 - 2,15</td></tr>
<tr><td colspan="17" rowspan="3">Коэффициент 0,55</td><td colspan="5"></td></tr>
<tr><td>1,0</td><td colspan="4">1,25</td></tr>
<tr><td colspan="5"></td></tr>
<tr><td colspan="22">Группы алюминиевых сплавов и твердости Группа сплавов Силумин и литейные сплавы Дюралюминий</td></tr>
<tr><td colspan="22">Твердость НВ, ГПа до 0,64 до 0,98</td></tr>
<tr><td colspan="22">Коэффициент 0,75 0,7</td></tr>
<tr><td colspan="22">Состояние обрабатываемой поверхности Состоите обрабатываемой поверхности без корки по корке</td></tr>
<tr><td colspan="22"></td></tr>
<tr><td colspan="14">Коэффициент</td><td colspan="8">1,0 1,2</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="16">Неполное штучное время Фрезерование плоскостей и уступов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа и алюминиевые Единичное и мелкосерийное производство</td><td colspan="6">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 80</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="14">7,5 - 10</td><td>80 -- 10</td><td rowspan="14">2</td><td>18</td><td>1,5</td><td>1,6</td><td>1,65</td><td>1,85</td><td>1,9</td><td>2,05</td><td>2,15</td><td>2,65</td><td>2,85</td><td>3,15</td><td>3,55</td><td>3,9</td><td>4,4</td><td>0,4</td><td>380</td><td>240</td><td rowspan="14">Не свыше 1,0</td></tr>
<tr><td>2</td><td rowspan="2">100 --- 10</td><td>18</td><td>1,65</td><td>1,75</td><td>1,85</td><td>2,05</td><td>2,1</td><td>2,25</td><td>2,45</td><td>2,95</td><td>3,25</td><td>3,6</td><td>4,05</td><td>4,5</td><td>5,0</td><td>0,48</td><td>300</td><td>190</td></tr>
<tr><td>3</td><td>27</td><td>1,7</td><td>1,8</td><td>1,85</td><td>2,1</td><td>2,15</td><td>2,3</td><td>2,5</td><td>3,0</td><td>3,25</td><td>3,65</td><td>4,1</td><td>4,55</td><td>5,0</td><td>0,48</td><td>300</td><td>190</td></tr>
<tr><td>4</td><td rowspan="2">125 --- 10</td><td>18</td><td>1,7</td><td>1,8</td><td>1,85</td><td>2,05</td><td>2,15</td><td>2,3</td><td>2,5</td><td>3,0</td><td>3,25</td><td>3,65</td><td>4,1</td><td>4,55</td><td>5,0</td><td>0,48</td><td>300</td><td>190</td></tr>
<tr><td>5</td><td>27</td><td>1,9</td><td>2,0</td><td>2,1</td><td>2,35</td><td>2,45</td><td>2,6</td><td>2,85</td><td>3,4</td><td>3,75</td><td>4,2</td><td>4,75</td><td>5,5</td><td>6,0</td><td>0,55</td><td>240</td><td>150</td></tr>
<tr><td>6</td><td rowspan="3">160 --- 10</td><td>18</td><td>1,75</td><td>1,85</td><td>1,9</td><td>2,1</td><td>2,2</td><td>2,35</td><td>2,55</td><td>3,05</td><td>3,3</td><td>3,7</td><td>4,15</td><td>4,6</td><td>5,0</td><td>0,48</td><td>300</td><td>120</td></tr>
<tr><td>7</td><td>27</td><td>1,95</td><td>2,0</td><td>2,2</td><td>2,4</td><td>2,55</td><td>2,7</td><td>2,95</td><td>3,5</td><td>3,85</td><td>4,3</td><td>4,85</td><td>5,5</td><td>6,0</td><td>0,55</td><td>240</td><td>96</td></tr>
<tr><td>8</td><td>40</td><td>2,05</td><td>2,15</td><td>2,35</td><td>2,5</td><td>2,6</td><td>2,8</td><td>3,0</td><td>3,55</td><td>3,9</td><td>4,35</td><td>4,95</td><td>5,5</td><td>6,5</td><td>0,55</td><td>240</td><td>96</td></tr>
<tr><td>9</td><td rowspan="3">200 --- 16</td><td>27</td><td>2,05</td><td>2,15</td><td>2,3</td><td>2,5</td><td>2,65</td><td>2,8</td><td>3,05</td><td>3,6</td><td>3,95</td><td>4,4</td><td>4,95</td><td>5,5</td><td>6,5</td><td>0,55</td><td>240</td><td>96</td></tr>
<tr><td>10</td><td>40</td><td>2,15</td><td>2,25</td><td>2,4</td><td>2,6</td><td>2,7</td><td>2,9</td><td>3,1</td><td>3,7</td><td>4,0</td><td>4,5</td><td>5,0</td><td>5,5</td><td>6,5</td><td>0,55</td><td>240</td><td>75</td></tr>
<tr><td>11</td><td>60</td><td>2,55</td><td>2,7</td><td>2,85</td><td>3,1</td><td>3,25</td><td>3,45</td><td>3,75</td><td>4,35</td><td>4,8</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>0,7</td><td>190</td><td>75</td></tr>
<tr><td>12</td><td rowspan="3">250 --- 12</td><td>27</td><td>2,15</td><td>2,25</td><td>2,35</td><td>2,6</td><td>2,7</td><td>2,9</td><td>3,1</td><td>3,65</td><td>4,0</td><td>4,45</td><td>5,0</td><td>5,5</td><td>6,5</td><td>0,55</td><td>240</td><td>75</td></tr>
<tr><td>13</td><td>40</td><td>2,55</td><td>2,7</td><td>2,85</td><td>3,1</td><td>3,25</td><td>3,45</td><td>3,75</td><td>4,35</td><td>4,8</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>0,7</td><td>190</td><td>60</td></tr>
<tr><td>14</td><td>60</td><td>2,7</td><td>2,85</td><td>3,0</td><td>3,25</td><td>3,4</td><td>3,6</td><td>3,9</td><td>4,55</td><td>4,95</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>0,7</td><td>190</td><td>60</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="16">Неполное штучное время Фрезерование плоскостей и уступов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа и алюминиевые Единичное и мелкосерийное производство</td><td colspan="6">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 80</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>15</td><td rowspan="3">7,5 - 10</td><td rowspan="3">315 --- 22</td><td rowspan="3">2</td><td>27</td><td>2,45</td><td>2,6</td><td>2,75</td><td>3,0</td><td>3,15</td><td>3,4</td><td>3,65</td><td>4,3</td><td>4,7</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>0,7</td><td>190</td><td>60</td><td rowspan="3">Не свыше 1,0</td></tr>
<tr><td>16</td><td>40</td><td>3,1</td><td>3,3</td><td>3,45</td><td>3,75</td><td>3,95</td><td>4,2</td><td>4,6</td><td>5,5</td><td>6,0</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>0,85</td><td>150</td><td>48</td></tr>
<tr><td>17</td><td>60</td><td>3,4</td><td>3,55</td><td>3,75</td><td>4,05</td><td>4,25</td><td>4,5</td><td>4,9</td><td>5,5</td><td>6,0</td><td>7,0</td><td>7,5</td><td>8,5</td><td>10</td><td>0,85</td><td>150</td><td>48</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
<tr><td colspan="22">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="17">Группы медных сплавов и твердости Группа сплавов Гомогенные</td><td colspan="5">Гетерогенные</td></tr>
<tr><td colspan="17">Твердость НВ, ГПа 0,59 - 0,74</td><td colspan="5">0,98 - 1,37 1,47 - 2,15</td></tr>
<tr><td colspan="17" rowspan="3">Коэффициент 0,55</td><td colspan="5"></td></tr>
<tr><td>1,0</td><td colspan="4">1,25</td></tr>
<tr><td colspan="5"></td></tr>
<tr><td colspan="22">Группы алюминиевых сплавов и твердости Группа сплавов Силумин и литейные сплавы Дюралюминий</td></tr>
<tr><td colspan="22">Твердость НВ, ГПа до 0,64 до 0,98</td></tr>
<tr><td colspan="22">Коэффициент 0,75 0,7</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="16">Неполное штучное время Фрезерование пазов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа и алюминиевые Единичное и мелкосерийное производство</td><td colspan="6">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 81</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td>Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="14">Время на проход, мин.</td></tr>
<tr><td>1</td><td rowspan="19">7,5 - 10</td><td rowspan="3">80 --- 10</td><td rowspan="3">25</td><td>5</td><td>1,45</td><td>1,5</td><td>1,6</td><td>1,75</td><td>1,85</td><td>1,95</td><td>2,1</td><td>2,55</td><td>2,8</td><td>3,05</td><td>3,45</td><td>3,8</td><td>4,35</td><td>0,4</td><td>380</td><td>300</td><td rowspan="19">Не свыше 3,5</td></tr>
<tr><td>2</td><td>10</td><td>1,55</td><td>1,65</td><td>1,75</td><td>1,95</td><td>2,05</td><td>2,15</td><td>2,35</td><td>2,85</td><td>3,15</td><td>3,5</td><td>3,95</td><td>4,45</td><td>5,0</td><td>0,48</td><td>300</td><td>300</td></tr>
<tr><td>3</td><td>15</td><td>1,6</td><td>1,7</td><td>1,8</td><td>1,95</td><td>2,05</td><td>2,2</td><td>2,4</td><td>2,9</td><td>3,15</td><td>3,55</td><td>4,0</td><td>4,45</td><td>5,0</td><td>0,48</td><td>300</td><td>300</td></tr>
<tr><td>4</td><td rowspan="4">100 --- 10</td><td rowspan="4">28</td><td>5</td><td>1,45</td><td>1,55</td><td>1,6</td><td>1,8</td><td>1,85</td><td>1,95</td><td>2,1</td><td>2,6</td><td>2,8</td><td>3,1</td><td>3,5</td><td>3,85</td><td>4,35</td><td>0,4</td><td>380</td><td>300</td></tr>
<tr><td>5</td><td>10</td><td>1,6</td><td>1,65</td><td>1,75</td><td>1,95</td><td>2,05</td><td>2,2</td><td>2,4</td><td>2,9</td><td>3,15</td><td>3,55</td><td>4,0</td><td>4,45</td><td>5,0</td><td>0,48</td><td>300</td><td>240</td></tr>
<tr><td>6</td><td>15</td><td>1,85</td><td>2,0</td><td>2,15</td><td>2,4</td><td>2,55</td><td>2,75</td><td>3,05</td><td>3,7</td><td>4,1</td><td>4,7</td><td>5,5</td><td>6,0</td><td>7,0</td><td>0,7</td><td>190</td><td>240</td></tr>
<tr><td>7</td><td>20</td><td>2,1</td><td>2,3</td><td>2,45</td><td>2,75</td><td>2,95</td><td>3,2</td><td>3,6</td><td>4,3</td><td>4,85</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>0,85</td><td>150</td><td>190</td></tr>
<tr><td>8</td><td rowspan="4">125 --- 10</td><td rowspan="4">32</td><td>5</td><td>1,65</td><td>1,75</td><td>1,85</td><td>2,1</td><td>2,2</td><td>2,35</td><td>2,6</td><td>3,15</td><td>3,5</td><td>3,95</td><td>4,5</td><td>5,0</td><td>6,0</td><td>0,55</td><td>240</td><td>190</td></tr>
<tr><td>9</td><td>10</td><td>1,85</td><td>2,0</td><td>2,15</td><td>2,4</td><td>2,55</td><td>2,75</td><td>3,05</td><td>3,65</td><td>4,1</td><td>4,65</td><td>5,5</td><td>6,0</td><td>7,0</td><td>0,7</td><td>190</td><td>190</td></tr>
<tr><td>10</td><td>15</td><td>2,1</td><td>2,3</td><td>2,5</td><td>2,8</td><td>2,95</td><td>3,25</td><td>3,6</td><td>4,3</td><td>4,85</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>0,85</td><td>150</td><td>190</td></tr>
<tr><td>11</td><td>20</td><td>2,45</td><td>2,7</td><td>2,9</td><td>3,25</td><td>3,5</td><td>3,8</td><td>4,3</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,5</td><td>1,0</td><td>120</td><td>150</td></tr>
<tr><td>12</td><td rowspan="4">160 --- 16</td><td rowspan="4">36</td><td>10</td><td>1,65</td><td>1,75</td><td>1,85</td><td>2,05</td><td>2,1</td><td>2,25</td><td>2,45</td><td>2,95</td><td>3,25</td><td>3,6</td><td>4,05</td><td>4,5</td><td>5,0</td><td>0,48</td><td>300</td><td>150</td></tr>
<tr><td>13</td><td>15</td><td>1,85</td><td>1,95</td><td>2,05</td><td>2,3</td><td>2,4</td><td>2,55</td><td>2,8</td><td>3,35</td><td>3,7</td><td>4,15</td><td>4,7</td><td>5,5</td><td>6,0</td><td>0,55</td><td>240</td><td>150</td></tr>
<tr><td>14</td><td>20</td><td>2,1</td><td>2,2</td><td>2,35</td><td>2,6</td><td>2,75</td><td>3,0</td><td>3,25</td><td>3,9</td><td>4,3</td><td>4,9</td><td>5,5</td><td>6,5</td><td>7,5</td><td>0,7</td><td>190</td><td>150</td></tr>
<tr><td>15</td><td>30</td><td>2,75</td><td>3,0</td><td>3,2</td><td>3,55</td><td>3,75</td><td>4,1</td><td>4,55</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,5</td><td>1,0</td><td>120</td><td>120</td></tr>
<tr><td>16</td><td rowspan="4">200 --- 16</td><td rowspan="4">40</td><td>10</td><td>1,8</td><td>1,95</td><td>2,05</td><td>2,3</td><td>2,4</td><td>2,55</td><td>2,8</td><td>3,35</td><td>3,7</td><td>4,15</td><td>4,7</td><td>5,5</td><td>6,0</td><td>0,55</td><td>240</td><td>120</td></tr>
<tr><td>17</td><td>15</td><td>2,1</td><td>2,25</td><td>2,4</td><td>2,65</td><td>2,8</td><td>3,0</td><td>3,3</td><td>3,3</td><td>4,35</td><td>4,9</td><td>5,5</td><td>6,5</td><td>7,5</td><td>0,7</td><td>190</td><td>120</td></tr>
<tr><td>18</td><td>20</td><td>2,4</td><td>2,6</td><td>2,8</td><td>3,1</td><td>3,25</td><td>3,55</td><td>3,9</td><td>4,6</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td>9,0</td><td>0,85</td><td>150</td><td>96</td></tr>
<tr><td>19</td><td>30</td><td>2,95</td><td>3,2</td><td>3,4</td><td>3,75</td><td>3,95</td><td>4,3</td><td>4,8</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11,0</td><td>1,0</td><td>120</td><td>96</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="5%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="16">Неполное штучное время Фрезерование пазов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа и алюминиевые Единичное и мелкосерийное производство</td><td colspan="7">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 81</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td>Глубина резания</td><td colspan="15">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">t, мм, до</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>200</td><td>250</td><td>300</td><td>400</td><td>500</td><td>600</td><td>750</td><td>950</td><td colspan="2">Добавлять на каждые 100 мм свыше 950</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">n, об./ мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td colspan="15">Время на проход, мин.</td></tr>
<tr><td>20</td><td rowspan="8">7,5 - 10</td><td rowspan="4">250 --- 20</td><td rowspan="4">45</td><td>10</td><td>1,85</td><td>2,0</td><td>2,1</td><td>2,3</td><td>2,45</td><td>2,6</td><td>2,85</td><td>3,4</td><td>3,75</td><td>4,2</td><td>4,75</td><td>5,5</td><td>6,0</td><td colspan="2">0,55</td><td>240</td><td>96</td><td rowspan="8">Не свыше 3,5</td></tr>
<tr><td>21</td><td>15</td><td>2,15</td><td>2,3</td><td>2,45</td><td>2,7</td><td>2,85</td><td>3,05</td><td>3,35</td><td>3,95</td><td>4,4</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td colspan="2">0,7</td><td>190</td><td>96</td></tr>
<tr><td>22</td><td>20</td><td>2,25</td><td>2,4</td><td>2,55</td><td>2,8</td><td>2,95</td><td>3,15</td><td>3,45</td><td>4,1</td><td>4,5</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td colspan="2">0,7</td><td>190</td><td>96</td></tr>
<tr><td>23</td><td>30</td><td>3,1</td><td>3,35</td><td>3,55</td><td>3,9</td><td>4,15</td><td>4,5</td><td>4,95</td><td>5,5</td><td>6,5</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,0</td><td colspan="2">1,0</td><td>120</td><td>75</td></tr>
<tr><td>24</td><td rowspan="4">315 --- 22</td><td rowspan="4">30</td><td>10</td><td>1,95</td><td>2,05</td><td>2,15</td><td>2,4</td><td>2,5</td><td>2,65</td><td>2,9</td><td>3,45</td><td>3,8</td><td>4,25</td><td>4,85</td><td>5,5</td><td>6,0</td><td colspan="2">0,55</td><td>240</td><td>75</td></tr>
<tr><td>25</td><td>15</td><td>2,25</td><td>2,4</td><td>2,55</td><td>2,8</td><td>2,95</td><td>3,15</td><td>3,45</td><td>4,05</td><td>4,5</td><td>5,0</td><td>6,0</td><td>6,5</td><td>7,5</td><td colspan="2">0,7</td><td>190</td><td>75</td></tr>
<tr><td>26</td><td>20</td><td>2,65</td><td>2,85</td><td>3,0</td><td>3,3</td><td>3,5</td><td>3,8</td><td>4,15</td><td>4,85</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td colspan="2">0,85</td><td>150</td><td>75</td></tr>
<tr><td>27</td><td>30</td><td>3,8</td><td>4,1</td><td>4,4</td><td>4,8</td><td>5,0</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>10,0</td><td>11,5</td><td>13,5</td><td colspan="2">1,25</td><td>96</td><td>60</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td colspan="2">о</td><td colspan="3"></td></tr>
<tr><td colspan="23">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="6" rowspan="6">Группы медных сплавов, твердости и продолжительности обработки</td><td colspan="17">Группа сплавов Гомогенные Гетерогенные</td></tr>
<tr><td colspan="13">Твердость НВ, ГПа 0,59 - 0,74 0,98 - 1,37</td><td colspan="4">1,47 - 2,15</td></tr>
<tr><td colspan="13">Продолжительность обработки, мин. до 10 свыше 10 -</td><td colspan="4">до 10 свыше 10</td></tr>
<tr><td colspan="13"></td><td colspan="4" rowspan="3">1,1 1,25</td></tr>
<tr><td colspan="11">Коэффициент 0,7 0,55</td><td colspan="2">1,0</td></tr>
<tr><td colspan="13"></td></tr>
<tr><td colspan="6" rowspan="4">Группы алюминиевых сплавов, твердости и продолжительности обработки</td><td colspan="17">Группа сплавов Силумин и литейные Дюралюминий сплавы</td></tr>
<tr><td colspan="17">Твердость НВ, ГПа до 0,64 до 0,98</td></tr>
<tr><td colspan="14">Продолжительность обработки, мин. до 10 свыше 10 до 10</td><td colspan="3">свыше 10</td></tr>
<tr><td colspan="14">Коэффициент 0,75 0,7 0,75</td><td colspan="3">0,7</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="15%"><col width="5%"><col width="6%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="4%"><col width="5%"><col width="5%"><col width="2%"><col width="2%"><col width="4%"><col width="5%"><col width="4%"><col width="4%"><col width="5%"><col width="8%"></colgroup>
<tr><td colspan="13">Неполное штучное время Сверление отверстий</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="7">Сверла спиральные из стали Р6М5</td></tr>
<tr><td colspan="7">Карта 82</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обрабатываемого</td><td colspan="13">Длина отверстия l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td rowspan="2">отверстия D, мм, до</td><td>10</td><td colspan="2">20 30</td><td>40</td><td>50</td><td>60</td><td colspan="2">80 100</td><td>125</td><td>150</td><td colspan="2">175</td><td>200</td><td colspan="2">S , о</td><td colspan="2" rowspan="2">v, м/мин.</td><td>N , р</td></tr>
<tr><td colspan="13">Время на проход, мин.</td><td colspan="2">мм/об.</td><td>кВт, до</td></tr>
<tr><td>1</td><td>8</td><td>0,47</td><td colspan="2">0,5 0,7</td><td>0,8</td><td>0,87</td><td>0,95</td><td colspan="2">1,2 1,45</td><td>1,65</td><td>2,3</td><td colspan="2">-</td><td>-</td><td colspan="2">0,4/0,3</td><td colspan="2">17,5/10</td><td rowspan="5">1</td></tr>
<tr><td>2</td><td>10</td><td>0,47</td><td colspan="2">0,5 0,55</td><td>0,8</td><td>0,87</td><td>0,95</td><td colspan="2">1,2 1,45</td><td>1,65</td><td>2,3</td><td colspan="2">-</td><td>-</td><td colspan="2">0,5/0,4</td><td colspan="2">15,7/10</td></tr>
<tr><td>3</td><td>13</td><td>0,48</td><td colspan="2">0,52 0,57</td><td>0,6</td><td>1,05</td><td>1,2</td><td colspan="2">1,45 1,8</td><td>2,1</td><td>2,4</td><td colspan="2">-</td><td>-</td><td colspan="2">0,6/0,45</td><td colspan="2">15,5/8</td></tr>
<tr><td>4</td><td>16</td><td>0,49</td><td colspan="2">0,53 0,58</td><td>0,63</td><td>0,7</td><td>1,25</td><td colspan="2">1,55 1,9</td><td>2,2</td><td>2,55</td><td colspan="2">-</td><td>-</td><td colspan="2">0,7/0,5</td><td colspan="2">15/8</td></tr>
<tr><td>5</td><td>20</td><td>0,5</td><td colspan="2">0,55 0,6</td><td>0,65</td><td>0,7</td><td>0,75</td><td colspan="2">1,65 2,0</td><td>2,35</td><td>2,7</td><td colspan="2">3,2</td><td>3,8</td><td colspan="2">0,8/0,6</td><td colspan="2">15,5/8</td></tr>
<tr><td>6</td><td>25</td><td>0,53</td><td colspan="2">0,57 0,63</td><td>0,70</td><td>0,75</td><td>0,8</td><td colspan="2">0,95 2,2</td><td>2,6</td><td>3,0</td><td colspan="2">3,6</td><td>4,2</td><td colspan="2">0,9/0,65</td><td colspan="2">15,5/7,8</td><td>2,3</td></tr>
<tr><td>7</td><td>30</td><td>0,56</td><td colspan="2">0,6 0,7</td><td>0,75</td><td>0,85</td><td>0,9</td><td colspan="2">1,05 2,3</td><td>2,9</td><td>3,3</td><td colspan="2">3,9</td><td>4,5</td><td colspan="2">1,0/0,75</td><td colspan="2">14/7,5</td><td>3,0</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td colspan="2">б в</td><td>г</td><td>д</td><td>е</td><td colspan="2">ж з</td><td>и</td><td>к</td><td colspan="2">л</td><td>м</td><td colspan="5"></td></tr>
<tr><td colspan="20">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4" rowspan="4">Твердости чугуна</td><td colspan="5">Твердость чугуна НВ, ГПа</td><td colspan="6">до 1,76</td><td colspan="3">1,76 - 2,15</td><td colspan="2">свыше 2,15</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="6" rowspan="3">0,9</td><td colspan="3"></td><td colspan="2" rowspan="3">1,1</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="4" rowspan="2">Числа одинаковых отверстий в одной детали</td><td colspan="5">Число отверстий</td><td colspan="6">до 3</td><td colspan="3">4 - 10</td><td colspan="2">11 - 25</td></tr>
<tr><td colspan="5">Коэффициент</td><td colspan="6">1,0</td><td colspan="3">0,9</td><td colspan="2">0,85</td></tr>
<tr><td colspan="4" rowspan="2">Жесткости детали или крепления</td><td colspan="5">Жесткость детали</td><td colspan="6">Деталь и установка жесткие</td><td colspan="5">Неустойчивые или тонкостенные детали</td></tr>
<tr><td colspan="5">Коэффициент</td><td colspan="6">1,0</td><td colspan="5">1,2</td></tr>
<tr><td colspan="4" rowspan="2">Характера обработки</td><td colspan="5">Обработка</td><td colspan="6">Под зенкерование и расточку резцом</td><td colspan="5">Под развертывание и нарезание резьбы метчиком</td></tr>
<tr><td colspan="5">Коэффициент</td><td colspan="6">1,0</td><td colspan="5">1,2</td></tr>
</table>


<a id="p102642"></a>*Примечание.* Меньшие скорости и подачи даны для отверстий длиной более 3D.


<table>
<colgroup><col width="4%"><col width="9%"><col width="14%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="6%"><col width="2%"><col width="5%"><col width="7%"></colgroup>
<tr><td colspan="13">Неполное штучное время Высверливание</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="7">Сверла спиральные из стали Р6М5</td></tr>
<tr><td colspan="7">Карта 83</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Диаметр обрабатываемого отверстия</td><td>Диаметр предварительно</td><td colspan="13">Длина отверстия l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>обработанного отверстия d,</td><td>10</td><td>20</td><td>30</td><td>40</td><td>50</td><td>60</td><td>80</td><td>100</td><td>125</td><td>150</td><td>175</td><td colspan="2">200</td><td>S , о</td><td colspan="2" rowspan="2">v, м/мин.</td><td>N , р</td></tr>
<tr><td>D, мм, до</td><td>мм, до</td><td colspan="13">Время на проход, мин.</td><td>мм/об.</td><td>кВт</td></tr>
<tr><td>1</td><td rowspan="2">25</td><td>10</td><td>0,57</td><td>0,6</td><td>0,65</td><td>0,70</td><td>0,73</td><td>0,77</td><td>0,85</td><td>0,95</td><td>1,15</td><td>1,25</td><td>1,35</td><td colspan="2">1,45</td><td>1,0</td><td colspan="2">19,5</td><td rowspan="2">2,2</td></tr>
<tr><td>2</td><td>15</td><td>0,55</td><td>0,58</td><td>0,62</td><td>0,65</td><td>0,7</td><td>0,75</td><td>0,80</td><td>0,85</td><td>1,0</td><td>1,1</td><td>1,2</td><td colspan="2">1,3</td><td>1,1</td><td colspan="2"></td></tr>
<tr><td>3</td><td rowspan="3">30</td><td>10</td><td>0,58</td><td>0,62</td><td>0,68</td><td>0,73</td><td>0,80</td><td>0,85</td><td>0,9</td><td>1,05</td><td>1,2</td><td>1,35</td><td>1,5</td><td colspan="2">1,6</td><td>1,0</td><td colspan="2" rowspan="2">19</td><td rowspan="3">2,3</td></tr>
<tr><td>4</td><td>15</td><td>0,57</td><td>0,6</td><td>0,65</td><td>0,7</td><td>0,75</td><td>0,80</td><td>0,85</td><td>0,95</td><td>1,15</td><td>1,25</td><td>1,35</td><td colspan="2">1,5</td><td>1,1</td></tr>
<tr><td>5</td><td>20</td><td>0,55</td><td>0,58</td><td>0,62</td><td>0,65</td><td>0,7</td><td>0,75</td><td>0,8</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,25</td><td colspan="2">1,35</td><td>1,2</td><td colspan="2">21</td></tr>
<tr><td>6</td><td rowspan="3">40</td><td>15</td><td>0,65</td><td>0,7</td><td>0,75</td><td>0,85</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,25</td><td>1,45</td><td>1,65</td><td>1,8</td><td colspan="2">2,0</td><td>1,0</td><td colspan="2">18,5</td><td rowspan="3">2,9</td></tr>
<tr><td>7</td><td>20</td><td>0,6</td><td>0,65</td><td>0,7</td><td>0,75</td><td>0,85</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,3</td><td>1,45</td><td>1,6</td><td colspan="2">1,75</td><td>1,1</td><td colspan="2">20</td></tr>
<tr><td>8</td><td>30</td><td>0,55</td><td>0,6</td><td>0,65</td><td>0,7</td><td>0,75</td><td>0,8</td><td>0,9</td><td>1,0</td><td>1,15</td><td>1,3</td><td>1,4</td><td colspan="2">1,55</td><td>1,2</td><td colspan="2">22</td></tr>
<tr><td>9</td><td rowspan="3">50</td><td>20</td><td>0,65</td><td>0,75</td><td>0,8</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,4</td><td>1,65</td><td>1,85</td><td>2,05</td><td colspan="2">2,3</td><td>1,1</td><td colspan="2" rowspan="2">18</td><td>3,3</td></tr>
<tr><td>10</td><td>30</td><td>0,6</td><td>0,65</td><td>0,75</td><td>0,8</td><td>0,9</td><td>0,95</td><td>1,1</td><td>1,2</td><td>1,45</td><td>1,6</td><td>1,8</td><td colspan="2">2,0</td><td>1,3</td><td>2,9</td></tr>
<tr><td>11</td><td>40</td><td>0,6</td><td>0,65</td><td>0,7</td><td>0,75</td><td>0,85</td><td>0,9</td><td>1,0</td><td>1,15</td><td>1,35</td><td>1,5</td><td>1,65</td><td colspan="2">1,85</td><td>1,3</td><td colspan="2">19,5</td><td>2,9</td></tr>
<tr><td>12</td><td rowspan="3">60</td><td>30</td><td>0,7</td><td>0,75</td><td>0,85</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,3</td><td>1,55</td><td>1,8</td><td>2,05</td><td>2,35</td><td colspan="2">2,55</td><td>1,2</td><td colspan="2" rowspan="2">17,5</td><td>3,8</td></tr>
<tr><td>13</td><td>40</td><td>0,65</td><td>0,70</td><td>0,8</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,4</td><td>1,65</td><td>1,85</td><td>2,1</td><td colspan="2">2,35</td><td>1,2</td><td>2,5</td></tr>
<tr><td>14</td><td>50</td><td>0,6</td><td>0,65</td><td>0,75</td><td>0,8</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,25</td><td>1,45</td><td>1,65</td><td>1,85</td><td colspan="2">2,05</td><td>1,4</td><td colspan="2">19,5</td><td>2,9</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td colspan="2">м</td><td colspan="4"></td></tr>
<tr><td colspan="20">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="5" rowspan="4">Твердости чугуна</td><td colspan="5">Твердость чугуна НВ, ГПа</td><td colspan="8">1,76 1,76 - 2,15</td><td colspan="2">свыше 2,15</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="8"></td><td colspan="2" rowspan="3">1,1</td></tr>
<tr><td colspan="5">0,9</td><td colspan="3">1,0</td></tr>
<tr><td colspan="8"></td></tr>
<tr><td colspan="5" rowspan="4">Жесткости детали или крепления</td><td colspan="5">Жесткость детали</td><td colspan="10">Деталь и установка Деталь неустойчивая жесткие тонкостенная</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="10"></td></tr>
<tr><td>1,0</td><td colspan="9">1,2</td></tr>
<tr><td colspan="10"></td></tr>
<tr><td colspan="5" rowspan="4">Числа одинаковых отверстий в одной детали</td><td colspan="5">Число отверстий</td><td colspan="8">до 3 4 - 10</td><td colspan="2">11 - 25</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="8"></td><td colspan="2" rowspan="3">0,85</td></tr>
<tr><td>1,0</td><td colspan="7">0,9</td></tr>
<tr><td colspan="8"></td></tr>
<tr><td colspan="5" rowspan="4">Характера обработки</td><td colspan="5">Обработка</td><td colspan="10">Под зенкерование и Под развертывание и расточку резцом нарезание резьбы метчиком</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="10"></td></tr>
<tr><td>1,0</td><td colspan="9">1,3</td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="18%"><col width="6%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="3%"><col width="2%"><col width="5%"><col width="2%"><col width="3%"><col width="2%"><col width="5%"><col width="2%"><col width="5%"><col width="9%"></colgroup>
<tr><td colspan="12">Неполное штучное время Зенкерование отверстий</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="12" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="8">Зенкеры из стали Р6М5</td></tr>
<tr><td colspan="8">Карта 84</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обрабатываемого</td><td colspan="2">Глубина резания</td><td colspan="11">Длина отверстия l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td rowspan="2">отверстия D, мм, до</td><td colspan="2" rowspan="2">t, мм, до</td><td>20</td><td>50</td><td>75</td><td>100</td><td colspan="2">125</td><td colspan="2">150</td><td>175</td><td colspan="2">200</td><td colspan="2" rowspan="2">S , о мм/об.</td><td colspan="2" rowspan="2">v, м/мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="11">Время на проход, мин.</td></tr>
<tr><td>1</td><td>15</td><td colspan="2" rowspan="9">1 - 2</td><td>0,4</td><td>0,5</td><td>0,6</td><td>0,65</td><td colspan="2">0,75</td><td colspan="2">0,85</td><td>0,9</td><td colspan="2">5,0</td><td colspan="2">0,8</td><td colspan="2">19</td><td rowspan="9">1</td></tr>
<tr><td>2</td><td>20</td><td>0,4</td><td>0,5</td><td>0,6</td><td>0,65</td><td colspan="2">0,75</td><td colspan="2">0,85</td><td>0,95</td><td colspan="2">1,0</td><td colspan="2">1,0</td><td colspan="2">20,5</td></tr>
<tr><td>3</td><td>25</td><td>0,45</td><td>0,5</td><td>0,6</td><td>0,7</td><td colspan="2">0,8</td><td colspan="2">0,9</td><td>1,0</td><td colspan="2">1,1</td><td colspan="2">1,1</td><td colspan="2">193</td></tr>
<tr><td>4</td><td>30</td><td>0,45</td><td>0,55</td><td>0,65</td><td>0,8</td><td colspan="2">0,9</td><td colspan="2">1,0</td><td>1,15</td><td colspan="2">1,25</td><td colspan="2">1,2</td><td colspan="2">18</td></tr>
<tr><td>5</td><td>35</td><td>0,45</td><td>0,55</td><td>0,7</td><td>0,8</td><td colspan="2">0,95</td><td colspan="2">1,05</td><td>1,2</td><td colspan="2">1,3</td><td colspan="2">1,35</td><td colspan="2">17,5</td></tr>
<tr><td>6</td><td>40</td><td>0,45</td><td>0,6</td><td>0,75</td><td>0,9</td><td colspan="2">1,0</td><td colspan="2">1,15</td><td>1,3</td><td colspan="2">1,45</td><td colspan="2">1,5</td><td colspan="2">15,5</td></tr>
<tr><td>7</td><td>50</td><td>0,5</td><td>0,6</td><td>0,8</td><td>0,9</td><td colspan="2">1,1</td><td colspan="2">1,25</td><td>1,4</td><td colspan="2">135</td><td colspan="2">1,8</td><td colspan="2">15,5</td></tr>
<tr><td>8</td><td>60</td><td>0,5</td><td>0,65</td><td>0,85</td><td>1,05</td><td colspan="2">1,2</td><td colspan="2">1,4</td><td>1,6</td><td colspan="2">1,75</td><td colspan="2">2,0</td><td colspan="2">14</td></tr>
<tr><td>9</td><td>80</td><td>0,55</td><td>0,75</td><td>1,05</td><td>1,3</td><td colspan="2">1,55</td><td colspan="2">1,8</td><td>2,0</td><td colspan="2">2,3</td><td colspan="2">2,2</td><td colspan="2">12,5</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td colspan="2">е</td><td>ж</td><td colspan="2">з</td><td colspan="5"></td></tr>
<tr><td colspan="20">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3" rowspan="4">Твердости чугуна</td><td colspan="6">Твердость чугуна НВ, ГПа</td><td colspan="9">1,76 1,76 - 2,15</td><td colspan="2">2,15</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="9"></td><td colspan="2" rowspan="3">1,1</td></tr>
<tr><td colspan="5">0,9</td><td colspan="4">1,0</td></tr>
<tr><td colspan="9"></td></tr>
<tr><td colspan="3" rowspan="4">Числа одинаковых отверстий в одной детали</td><td colspan="6">Число отверстий</td><td colspan="9">до 3 4 - 10</td><td colspan="2">11 - 25</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="9"></td><td colspan="2" rowspan="3">0,85</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7">0,9</td></tr>
<tr><td colspan="9"></td></tr>
<tr><td colspan="3" rowspan="4">Жесткости детали или крепления</td><td colspan="6">Жесткость детали</td><td colspan="7">Деталь и установка жесткие</td><td colspan="4">Деталь неустойчивая или тонкостенная</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="7"></td><td colspan="4" rowspan="3">1,1</td></tr>
<tr><td colspan="2">1,0</td><td colspan="5"></td></tr>
<tr><td colspan="7"></td></tr>
<tr><td colspan="3" rowspan="4">Характера обработки</td><td colspan="6">Обработка</td><td colspan="7">Под чистовое зенкерование и расточку резцом</td><td colspan="4">Под развертывание и нарезание резьбы метчиком</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="7"></td><td colspan="4" rowspan="3">1,3</td></tr>
<tr><td colspan="2">1,0</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="18%"><col width="6%"><col width="2%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="3%"><col width="2%"><col width="5%"><col width="5%"><col width="2%"><col width="5%"><col width="2%"><col width="5%"><col width="9%"></colgroup>
<tr><td colspan="12">Неполное штучное время Зенкерование отверстий</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="12" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="7">Зенкеры с пластинками ВК8</td></tr>
<tr><td colspan="7">Карта 85</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр обрабатываемого</td><td colspan="2">Глубина резания</td><td colspan="10">Длина отверстия l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td rowspan="2">отверстия D, мм, до</td><td colspan="2" rowspan="2">t, мм, до</td><td>20</td><td>50</td><td>75</td><td>100</td><td colspan="2">125</td><td colspan="2">150</td><td>175</td><td>200</td><td colspan="2" rowspan="2">S , о мм/об.</td><td colspan="2" rowspan="2">v, м/мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td colspan="10">Время на проход, мин.</td></tr>
<tr><td>1</td><td>15</td><td colspan="2" rowspan="9">1 - 3</td><td>0,35</td><td>0,37</td><td>0,39</td><td>0,4</td><td colspan="2">0,42</td><td colspan="2">0,44</td><td>0,46</td><td>0,48</td><td colspan="2">0,8</td><td colspan="2">94</td><td>4,0</td></tr>
<tr><td>2</td><td>20</td><td>0,36</td><td>0,39</td><td>0,40</td><td>0,42</td><td colspan="2">0,44</td><td colspan="2">0,46</td><td>0,48</td><td>0,50</td><td colspan="2">1,0</td><td colspan="2">80</td><td>3,5</td></tr>
<tr><td>3</td><td>25</td><td>0,37</td><td>0,39</td><td>0,41</td><td>0,43</td><td colspan="2">0,46</td><td colspan="2">0,48</td><td>0,5</td><td>0,54</td><td colspan="2">1,1</td><td colspan="2">78</td><td>4,0</td></tr>
<tr><td>4</td><td>30</td><td>0,37</td><td>0,4</td><td>0,43</td><td>0,45</td><td colspan="2">0,48</td><td colspan="2">0,5</td><td>0,53</td><td>0,57</td><td colspan="2">1,2</td><td colspan="2">15</td><td>4,3</td></tr>
<tr><td>5</td><td>35</td><td>0,37</td><td>0,4</td><td>0,44</td><td>0,47</td><td colspan="2">0,5</td><td colspan="2">0,53</td><td>0,57</td><td>0,6</td><td colspan="2">1,35</td><td colspan="2">66</td><td>4,5</td></tr>
<tr><td>6</td><td>40</td><td>0,38</td><td>0,4</td><td>0,45</td><td>0,48</td><td colspan="2">0,5</td><td colspan="2">0,55</td><td>0,58</td><td>0,63</td><td colspan="2">1,5</td><td colspan="2">63</td><td>4,0</td></tr>
<tr><td>7</td><td>50</td><td>0,38</td><td>0,41</td><td>0,45</td><td>0,5</td><td colspan="2">0,53</td><td colspan="2">0,57</td><td>0,6</td><td>0,65</td><td colspan="2">1,8</td><td colspan="2">63</td><td>4,5</td></tr>
<tr><td>8</td><td>60</td><td>0,4</td><td>0,44</td><td>0,5</td><td>0,60</td><td colspan="2">0,6</td><td colspan="2">0,65</td><td>0,72</td><td>0,77</td><td colspan="2">2,0</td><td colspan="2">47</td><td>4,3</td></tr>
<tr><td>9</td><td>80</td><td>0,4</td><td>0,45</td><td>0,52</td><td>0,6</td><td colspan="2">0,65</td><td colspan="2">0,7</td><td>0,77</td><td>0,85</td><td colspan="2">2,2</td><td colspan="2">50</td><td>4,5</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="2">д</td><td colspan="2">е</td><td>ж</td><td>з</td><td colspan="5"></td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3" rowspan="4">Твердости чугуна</td><td colspan="6">Твердость чугуна НВ, ГПа</td><td colspan="6">до 2,15</td><td colspan="4">свыше 2,15</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="6"></td><td colspan="4" rowspan="3">1,1</td></tr>
<tr><td colspan="2">1,0</td><td colspan="4"></td></tr>
<tr><td colspan="6"></td></tr>
<tr><td colspan="3" rowspan="4">Числа одинаковых отверстий в одной детали</td><td colspan="6">Число отверстий</td><td colspan="8">до 3 4 - 10</td><td colspan="2">11 - 25</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="8"></td><td colspan="2" rowspan="3">0,85</td></tr>
<tr><td colspan="2">1,0</td><td colspan="6">0,9</td></tr>
<tr><td colspan="8"></td></tr>
<tr><td colspan="3" rowspan="4">Жесткости детали или крепления</td><td colspan="6">Жесткость детали</td><td colspan="6">Деталь и установка жесткие</td><td colspan="4">Деталь неустойчивая или тонкостенная</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="6"></td><td colspan="4" rowspan="3">1,1</td></tr>
<tr><td colspan="2">1,0</td><td colspan="4"></td></tr>
<tr><td colspan="6"></td></tr>
<tr><td colspan="3" rowspan="4">Характера обработки</td><td colspan="6">Обработка</td><td colspan="6">Под чистовое зенкерование и расточку резцом</td><td colspan="4">Под развертывание и нарезание резьбы метчиком</td></tr>
<tr><td colspan="6" rowspan="3">Коэффициент</td><td colspan="6"></td><td colspan="4" rowspan="3">1,3</td></tr>
<tr><td colspan="2">1,0</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="6%"><col width="7%"></colgroup>
<tr><td colspan="13">Неполное штучное время Развертывание отверстий, Rz 20 - Rz 2,5, 1Т9 - 1Т8 квалитет</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="6">Развертки из стали Р6М5</td></tr>
<tr><td colspan="6">Карта 86</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Параметр шероховатости, квалитет</td><td rowspan="2">Диаметр обрабатываемого отверстия</td><td colspan="11">Длина отверстия l, мм, до</td><td colspan="5">Режимы резания</td></tr>
<tr><td>10</td><td>20</td><td>30</td><td>40</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td colspan="2" rowspan="2">S , о мм/об.</td><td colspan="2" rowspan="2">v, м/мин.</td><td rowspan="2">N , р кВт, до</td></tr>
<tr><td>D, мм, до</td><td colspan="11">Время на проход, мин.</td></tr>
<tr><td>1</td><td>Обработка одной</td><td>10</td><td>0,4</td><td>0,42</td><td>0,45</td><td>0,47</td><td>0,5</td><td>0,55</td><td>0,60</td><td>0,70</td><td>0,75</td><td>0,8</td><td>0,9</td><td colspan="2">1,7</td><td colspan="2">7,2</td><td rowspan="20"></td></tr>
<tr><td>2</td><td>разверткой Rz 20</td><td>15</td><td>0,43</td><td>0,45</td><td>0,5</td><td>0,55</td><td>0,6</td><td>0,65</td><td>0,75</td><td>0,85</td><td>0,95</td><td>1,05</td><td>1,1</td><td colspan="2">1,9</td><td colspan="2">7,0</td></tr>
<tr><td>3</td><td>- Rz 2,5, 1Т9 - 1Т8</td><td>20</td><td>0,5</td><td>0,55</td><td>0,60</td><td>0,65</td><td>0,7</td><td>0,8</td><td>0,85</td><td>1,05</td><td>1,2</td><td>1,35</td><td>1,45</td><td colspan="2">2,0</td><td colspan="2">6,3</td></tr>
<tr><td>4</td><td rowspan="7">квалитет</td><td>25</td><td>0,5</td><td>0,55</td><td>0,65</td><td>0,70</td><td>0,75</td><td>0,85</td><td>1,0</td><td>1,15</td><td>1,3</td><td>1,5</td><td>1,65</td><td colspan="2">2,2</td><td colspan="2">6,2</td></tr>
<tr><td>5</td><td>30</td><td>0,55</td><td>0,6</td><td>0,7</td><td>0,80</td><td>0,85</td><td>0,95</td><td>1,15</td><td>1,35</td><td>1,5</td><td>1,7</td><td>1,9</td><td colspan="2">2,4</td><td colspan="2">5,6</td></tr>
<tr><td>6</td><td>35</td><td>0,6</td><td>0,65</td><td>0,75</td><td>0,85</td><td>0,95</td><td>1,1</td><td>1,3</td><td>1,5</td><td>1,8</td><td>2,0</td><td>2,2</td><td colspan="2">2,6</td><td colspan="2">5,3</td></tr>
<tr><td>7</td><td>40</td><td>0,7</td><td>0,75</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,25</td><td>1,5</td><td>1,8</td><td>2,0</td><td>2,3</td><td>2,6</td><td colspan="2">2,7</td><td colspan="2">4,8</td></tr>
<tr><td>8</td><td>50</td><td>0,75</td><td>0,85</td><td>1,0</td><td>1,1</td><td>1,25</td><td>1,45</td><td>1,75</td><td>2,1</td><td>2,4</td><td>2,7</td><td>3,0</td><td colspan="2">2,9</td><td colspan="2">4,7</td></tr>
<tr><td>9</td><td>60</td><td>0,8</td><td>0,9</td><td>1,1</td><td>1,2</td><td>1,3</td><td>1,6</td><td>1,9</td><td>2,3</td><td>2,6</td><td>2,9</td><td>3,3</td><td colspan="2">3,2</td><td colspan="2">4,7</td></tr>
<tr><td>10</td><td>80</td><td>0,9</td><td>1,0</td><td>1,15</td><td>1,35</td><td>1,5</td><td>1,8</td><td>2,2</td><td>2,6</td><td>3,0</td><td>3,4</td><td>3,8</td><td colspan="2">4,1</td><td colspan="2">4,1</td></tr>
<tr><td>11</td><td>Обработка двумя</td><td>10</td><td>0,8</td><td>0,85</td><td>0,9</td><td>0,95</td><td>1,0</td><td>1,1</td><td>1,25</td><td>1,4</td><td>1,5</td><td>1,65</td><td>1,8</td><td colspan="2">2,2 - 1,4</td><td colspan="2">6,3 - 7,8</td></tr>
<tr><td>12</td><td>развертками Rz</td><td>15</td><td>0,9</td><td>0,95</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,35</td><td>1,6</td><td>1,8</td><td>2,0</td><td>2,2</td><td>2,4</td><td colspan="2">2,3 - 1,5</td><td colspan="2">5,9 - 7,5</td></tr>
<tr><td>13</td><td>2,5 - Rz 1,25, 1Т7</td><td>20</td><td>1,0</td><td>1,05</td><td>1,15</td><td>1,3</td><td>1,4</td><td>1,6</td><td>1,9</td><td>2,2</td><td>2,4</td><td>2,7</td><td>3,0</td><td colspan="2">2,6 - 1,7</td><td colspan="2">5,7 - 6,3</td></tr>
<tr><td>14</td><td rowspan="7">квалитет</td><td>25</td><td>1,1</td><td>1,15</td><td>1,3</td><td>1,45</td><td>1,6</td><td>1,9</td><td>2,2</td><td>2,5</td><td>2,9</td><td>3,2</td><td>3,6</td><td colspan="2">2,7 - 1,9</td><td colspan="2">4,7 - 6,2</td></tr>
<tr><td>15</td><td>30</td><td>1,15</td><td>1,25</td><td>1,4</td><td>1,55</td><td>1,7</td><td>2,0</td><td>2,4</td><td>2,8</td><td>3,2</td><td>3,6</td><td>4,0</td><td colspan="2">3,1 - 2,0</td><td colspan="2">4,6 - 5,6</td></tr>
<tr><td>16</td><td>35</td><td>1,25</td><td>1,4</td><td>1,6</td><td>1,3</td><td>2,0</td><td>2,3</td><td>2,3</td><td>3,3</td><td>3,3</td><td>4,3</td><td>4,3</td><td colspan="2">3,2 - 2,0</td><td colspan="2">4,4 - 5,5</td></tr>
<tr><td>17</td><td>40</td><td>1,45</td><td>1,6</td><td>1,3</td><td>2,0</td><td>2,3</td><td>2,7</td><td>3,3</td><td>3,3</td><td>4,4</td><td>5,0</td><td>5,5</td><td colspan="2">3,4 - 2,2</td><td colspan="2">4,0 - 5,0</td></tr>
<tr><td>18</td><td>50</td><td>1,5</td><td>1,7</td><td>1,9</td><td>2,2</td><td>2,5</td><td>2,9</td><td>3,5</td><td>4,1</td><td>4,3</td><td>5,5</td><td>6,0</td><td colspan="2">3,3 - 2,6</td><td colspan="2">3,9 - 4,9</td></tr>
<tr><td>19</td><td>60</td><td>1,6</td><td>1,3</td><td>2,1</td><td>2,4</td><td>2,7</td><td>3,2</td><td>3,9</td><td>4,5</td><td>5,0</td><td>6,0</td><td>6,5</td><td colspan="2">4,3 - 2,9</td><td colspan="2">3,3 - 4,7</td></tr>
<tr><td>20</td><td>80</td><td>1,75</td><td>2,0</td><td>2,3</td><td>2,6</td><td>2,9</td><td>3,4</td><td>4,2</td><td>5,0</td><td>5,5</td><td>6,5</td><td>7,5</td><td colspan="2">5,1 - 3,4</td><td colspan="2">4,0 - 4,5</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td colspan="5"></td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="11" rowspan="2">Твердости чугуна Твердость чугуна НВ, ГПа</td><td colspan="3">1,76</td><td colspan="3">1,76 - 2,15</td><td colspan="2">свыше 2,15</td></tr>
<tr><td colspan="3" rowspan="3">0,9</td><td colspan="3"></td><td colspan="2" rowspan="3">1,1</td></tr>
<tr><td colspan="11" rowspan="2">Коэффициент</td><td>1,0</td><td colspan="2"></td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="7%"><col width="3%"><col width="5%"><col width="5%"><col width="6%"><col width="2%"><col width="3%"><col width="2%"><col width="3%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="5%"><col width="4%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="3%"><col width="8%"></colgroup>
<tr><td colspan="15">Неполное штучное время Сверление отверстий</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="15">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="7">Сверла спиральные из стали Р6М5</td></tr>
<tr><td colspan="15">Единичное и мелкосерийное производство</td><td colspan="7">Карта 87</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="2">Диаметр обрабатываемого отверстия</td><td colspan="15">Длина отверстия l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>10</td><td>20</td><td>30</td><td colspan="2">40</td><td colspan="2">50</td><td>60</td><td>80</td><td colspan="2">100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>S , о</td><td colspan="2" rowspan="2">v, м/мин.</td><td>N , р</td></tr>
<tr><td colspan="2">D, мм, до</td><td colspan="15">Время на проход, мин.</td><td>мм/об.</td><td>кВт, до</td></tr>
<tr><td>1</td><td colspan="2">8</td><td>0,5</td><td>0,56</td><td>0,96</td><td colspan="2">1,15</td><td colspan="2">1,35</td><td>1,6</td><td>1,95</td><td colspan="2">2,3</td><td>2,85</td><td>3,5</td><td>-</td><td>-</td><td>0,2 ---- 0,15</td><td colspan="2">17,5 ---- 10</td><td rowspan="6">1</td></tr>
<tr><td>2</td><td colspan="2">10</td><td>0,5</td><td>0,58</td><td>0,65</td><td colspan="2">1,25</td><td colspan="2">1,5</td><td>1,75</td><td>2,15</td><td colspan="2">2,75</td><td>3,2</td><td>3,9</td><td>-</td><td>-</td><td>0,25 ---- 0,19</td><td colspan="2">17,5 ---- 8,5</td></tr>
<tr><td>3</td><td colspan="2">13</td><td>0,55</td><td>0,62</td><td>0,7</td><td colspan="2">0,8</td><td colspan="2">1,75</td><td>2,1</td><td>2,5</td><td colspan="2">3,2</td><td>3,8</td><td>4,6</td><td>-</td><td>-</td><td>0,28 ---- 0,21</td><td colspan="2">17,5 ---- 8,2</td></tr>
<tr><td>4</td><td colspan="2">16</td><td>0,55</td><td>0,64</td><td>0,75</td><td colspan="2">0,85</td><td colspan="2">0,95</td><td>2,2</td><td>2,6</td><td colspan="2">3,4</td><td>4,0</td><td>4,9</td><td>-</td><td>-</td><td>0,35 ---- 0,26</td><td colspan="2">15 --- 7,5</td></tr>
<tr><td>5</td><td colspan="2">20</td><td>0,6</td><td>0,68</td><td>0,80</td><td colspan="2">0,9</td><td colspan="2">1,0</td><td>1,15</td><td>2,8</td><td colspan="2">3,5</td><td>4,2</td><td>5,0</td><td>6,0</td><td>7,0</td><td>0,40 ---- 0,30</td><td colspan="2">15 --- 7,8</td></tr>
<tr><td>6</td><td colspan="2">25</td><td>0,65</td><td>0,75</td><td>0,87</td><td colspan="2">1,0</td><td colspan="2">1,1</td><td>1,25</td><td>1,45</td><td colspan="2">4,0</td><td>4,7</td><td>5,5</td><td>6,5</td><td>7,5</td><td>0,45 ---- 0,34</td><td colspan="2">15 --- 7,4</td></tr>
<tr><td>7</td><td colspan="2">30</td><td>0,7</td><td>0,80</td><td>0,95</td><td colspan="2">1,1</td><td colspan="2">1,25</td><td>1,4</td><td>1,6</td><td colspan="2">2,1</td><td>5,3</td><td>6,0</td><td>7,0</td><td>8,0</td><td>0,50 ---- 0,38</td><td colspan="2">15 --- 7,4</td><td>2,5</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td colspan="2">г</td><td colspan="2">д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td><td>м</td><td colspan="4"></td></tr>
<tr><td colspan="22">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="5">Группы стали и предела прочности</td><td colspan="5">Группа стали</td><td colspan="15">Углеродистые, хромистые, Марганцовистые, никелевые, хромоникелевые хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="5">Предел прочности сигма , ГПа в</td><td colspan="3">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="7">свыше 0,74 до 0,59 0,59 - 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="3" rowspan="3">0,8</td><td colspan="3"></td><td colspan="7" rowspan="3">1,25 1,1 1,2</td><td colspan="2" rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="2" rowspan="4">Числа одинаковых отверстий в одной детали</td><td colspan="5">Число отверстий</td><td colspan="6">до 3</td><td colspan="9">4 - 10 11 - 25</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="6"></td><td colspan="9" rowspan="3">0,9 0,85</td></tr>
<tr><td colspan="2">1,0</td><td colspan="4"></td></tr>
<tr><td colspan="6"></td></tr>
<tr><td colspan="2" rowspan="4">Жесткости детали или крепления</td><td colspan="5">Жесткость детали</td><td colspan="15">Деталь и установка жесткие Деталь неустойчивая или тонкостенная</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="15"></td></tr>
<tr><td colspan="2">1,0</td><td colspan="13">1,1</td></tr>
<tr><td colspan="15"></td></tr>
<tr><td colspan="2" rowspan="4">Характера обработки</td><td colspan="5">Обработка</td><td colspan="15">Под зенкерование и расточку Под развертывание и нарезание резцом резьбы метчиком</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="15"></td></tr>
<tr><td colspan="2">1,0</td><td colspan="13">1,3</td></tr>
</table>


<a id="p102757"></a>*Примечание.* Меньшие скорости и подачи даны для отверстий длиной более 3D.


<table>
<colgroup><col width="4%"><col width="9%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="13">Неполное штучное время Рассверливание отверстий</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Сверла спиральные из стали Р6М5</td></tr>
<tr><td colspan="13">Единичное и мелкосерийное производство</td><td colspan="3">Карта 88</td><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Диаметр обрабатываемого отверстия</td><td rowspan="3">Диаметр предварительно просверленного отверстия</td><td colspan="12">Длина отверстия l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td>10</td><td>20</td><td>30</td><td>40</td><td>50</td><td>60</td><td>80</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>S , о</td><td rowspan="2">v, м/мин.</td><td>N , р</td></tr>
<tr><td>D, мм, до</td><td colspan="12">Время на проход, мин.</td><td>мм/об.</td><td>кВт, до</td></tr>
<tr><td>1</td><td rowspan="2">25</td><td>10</td><td>0,6</td><td>0,65</td><td>0,75</td><td>0,8</td><td>0,9</td><td>0,95</td><td>1,1</td><td>1,25</td><td>1,45</td><td>1,65</td><td>1,85</td><td>2,0</td><td>0,9</td><td>12,5</td><td>1,8</td></tr>
<tr><td>2</td><td>15</td><td>0,55</td><td>0,6</td><td>0,65</td><td>0,7</td><td>0,75</td><td>0,85</td><td>0,9</td><td>1,0</td><td>1,2</td><td>1,35</td><td>1,45</td><td>1,6</td><td>1,0</td><td>15,5</td><td>1,0</td></tr>
<tr><td>3</td><td rowspan="3">30</td><td>10</td><td>0,65</td><td>0,7</td><td>0,8</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,25</td><td>1,45</td><td>1,7</td><td>1,95</td><td>2,2</td><td>2,45</td><td rowspan="2">0,9</td><td>12</td><td></td></tr>
<tr><td>4</td><td>15</td><td>0,6</td><td>0,65</td><td>0,75</td><td>0,8</td><td>0,9</td><td>0,95</td><td>1,1</td><td>1,25</td><td>1,45</td><td>1,65</td><td>1,85</td><td>2,0</td><td rowspan="2">15</td><td>2,2</td></tr>
<tr><td>5</td><td>20</td><td>0,6</td><td>0,65</td><td>0,7</td><td>0,75</td><td>0,85</td><td>0,9</td><td>1,0</td><td>1,15</td><td>1,35</td><td>1,5</td><td>1,7</td><td>1,85</td><td>1,0</td><td>1,0</td></tr>
<tr><td>6</td><td rowspan="3">40</td><td>15</td><td>0,7</td><td>0,8</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,4</td><td>1,6</td><td>1,9</td><td>2,15</td><td>2,45</td><td>3,0</td><td rowspan="2">1,0</td><td rowspan="2">12,5</td><td>3,0</td></tr>
<tr><td>7</td><td>20</td><td>0,65</td><td>0,7</td><td>0,8</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,4</td><td>1,65</td><td>1,85</td><td>2,1</td><td>2,3</td><td>2,9</td></tr>
<tr><td>8</td><td>30</td><td>0,6</td><td>0,65</td><td>0,75</td><td>0,85</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,3</td><td>1,55</td><td>1,75</td><td>1,95</td><td>2,15</td><td>1,1</td><td>15</td><td>1,9</td></tr>
<tr><td>9</td><td rowspan="3">50</td><td>20</td><td>0,8</td><td>0,9</td><td>1,05</td><td>1,1</td><td>1,35</td><td>1,45</td><td>1,7</td><td>2,0</td><td>2,4</td><td>2,7</td><td>3,1</td><td>3,5</td><td rowspan="2">1,0</td><td rowspan="2">12</td><td>3,5</td></tr>
<tr><td>10</td><td>30</td><td>0,7</td><td>0,8</td><td>0,9</td><td>1,05</td><td>1,15</td><td>1,25</td><td>1,45</td><td>1,7</td><td>2,0</td><td>2,3</td><td>2,6</td><td>2,9</td><td>2,5</td></tr>
<tr><td>11</td><td>40</td><td>0,65</td><td>0,7</td><td>0,8</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,25</td><td>1,5</td><td>1,75</td><td>2,0</td><td>2,3</td><td>2,5</td><td>1,2</td><td>14</td><td>1,0</td></tr>
<tr><td>12</td><td rowspan="3">60</td><td>30</td><td>0,85</td><td>1,0</td><td>1,15</td><td>1,35</td><td>1,55</td><td>1,7</td><td>2,0</td><td>2,35</td><td>2,8</td><td>3,3</td><td>3,8</td><td>4,2</td><td rowspan="2">1,0</td><td rowspan="2">11,5</td><td>3,3</td></tr>
<tr><td>13</td><td>40</td><td>0,75</td><td>0,85</td><td>1,0</td><td>1,2</td><td>1,35</td><td>1,5</td><td>1,75</td><td>2,05</td><td>2,45</td><td>2,8</td><td>3,2</td><td>3,6</td><td>2,5</td></tr>
<tr><td>14</td><td>50</td><td>0,7</td><td>0,75</td><td>0,9</td><td>1,05</td><td>1,15</td><td>1,3</td><td>1,5</td><td>1,75</td><td>2,1</td><td>2,45</td><td>2,75</td><td>3,1</td><td>1,2</td><td>13</td><td>1,0</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="20%"><col width="17%"><col width="5%"><col width="3%"><col width="5%"><col width="7%"><col width="6%"><col width="5%"><col width="8%"><col width="7%"><col width="5%"><col width="11%"></colgroup>
<tr><td colspan="7">Неполное штучное время Рассверливание отверстий</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="7">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Сверла спиральные из стали Р6М5</td></tr>
<tr><td colspan="7">Единичное и мелкосерийное производство</td><td colspan="3">Карта 88</td><td colspan="2">Лист 2</td></tr>
<tr><td colspan="12">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="5">Группы стали и предел прочности</td><td>Группа стали</td><td colspan="6">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="4">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td colspan="2">свыше 0,74</td><td>до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="2"></td><td colspan="2" rowspan="3">1,25</td><td rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td rowspan="4">Числа одинаковых отверстий в одной детали</td><td>Чисто отверстий</td><td colspan="4">до 3</td><td colspan="3">4 - 10</td><td colspan="3">11 - 25</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="3" rowspan="3">0,9</td><td colspan="3" rowspan="3">0,85</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td rowspan="4">Жесткости детали или крепления</td><td>Жесткость детали</td><td colspan="6">Деталь и установка жесткая</td><td colspan="4">Деталь неустойчивая тонкостенная</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="6"></td><td colspan="4" rowspan="3">1,1</td></tr>
<tr><td>1,0</td><td colspan="5"></td></tr>
<tr><td colspan="6"></td></tr>
<tr><td rowspan="4">Характера обработки</td><td>Обработка</td><td colspan="6">Под зенкерование и расточку резцом</td><td colspan="4">Под развертывание и нарезание резьбы метчиком</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="6"></td><td colspan="4" rowspan="3">1,3</td></tr>
<tr><td>1,0</td><td colspan="5"></td></tr>
</table>



<table>
<colgroup><col width="6%"><col width="11%"><col width="8%"><col width="9%"><col width="2%"><col width="3%"><col width="2%"><col width="3%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="5%"><col width="2%"><col width="3%"><col width="5%"><col width="8%"><col width="4%"><col width="3%"><col width="9%"></colgroup>
<tr><td colspan="13">Неполное штучное время Зенкерование отверстий</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13">Сталь конструкционная углеродистая, сигма = 0,59 - 0,7 ГПа в</td><td colspan="7">Зенкеры из стали Р6М5</td></tr>
<tr><td colspan="13">Единичное и мелкосерийное производство</td><td colspan="7">Карта 89</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2">Диаметр обрабатываемого отверстия D, мм,</td><td>Глубина резания t, мм,</td><td colspan="12">Длина обрабатываемой поверхности l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td colspan="2" rowspan="2">до</td><td rowspan="2">до</td><td colspan="2">20</td><td colspan="2">50</td><td>75</td><td>100</td><td colspan="2">125</td><td>150</td><td colspan="2">175</td><td>200</td><td>S , о</td><td colspan="2" rowspan="2">v, м/мин.</td><td>N , р</td></tr>
<tr><td colspan="12">Время на проход, мин.</td><td>мм/об.</td><td>кВт, до</td></tr>
<tr><td>1</td><td colspan="2">15</td><td rowspan="8">1 - 2</td><td colspan="2">0,5</td><td colspan="2">0,65</td><td>0,85</td><td>1,05</td><td colspan="2">1,2</td><td>1,4</td><td colspan="2">1,55</td><td>1,75</td><td>0,5</td><td colspan="2">14,0</td><td rowspan="9">1</td></tr>
<tr><td>2</td><td colspan="2">20</td><td colspan="2">0,5</td><td colspan="2">0,65</td><td>0,9</td><td>1,1</td><td colspan="2">1,3</td><td>1,45</td><td colspan="2">1,65</td><td>1,85</td><td>0,65</td><td colspan="2">13,5</td></tr>
<tr><td>3</td><td colspan="2">25</td><td colspan="2">0,55</td><td colspan="2">0,7</td><td>0,95</td><td>1,2</td><td colspan="2">1,4</td><td>1,65</td><td colspan="2">1,85</td><td>2,1</td><td>0,8</td><td colspan="2">11,7</td></tr>
<tr><td>4</td><td colspan="2">30</td><td colspan="2">0,55</td><td colspan="2">0,75</td><td>1,05</td><td>1,3</td><td colspan="2">1,55</td><td>1,8</td><td colspan="2">2,0</td><td>2,3</td><td>0,9</td><td colspan="2">11,5</td></tr>
<tr><td>5</td><td colspan="2">35</td><td colspan="2">0,6</td><td colspan="2">0,8</td><td>1,1</td><td>1,4</td><td colspan="2">1,65</td><td>1,9</td><td colspan="2">2,2</td><td>2,45</td><td>1,0</td><td colspan="2">11,0</td></tr>
<tr><td>6</td><td colspan="2">40</td><td colspan="2">0,65</td><td colspan="2">0,9</td><td>1,3</td><td>1,65</td><td colspan="2">2,0</td><td>2,3</td><td colspan="2">2,7</td><td>3,0</td><td>1,05</td><td colspan="2">9,3</td></tr>
<tr><td>7</td><td colspan="2">50</td><td colspan="2">0,7</td><td colspan="2">1,0</td><td>1,45</td><td>1,85</td><td colspan="2">2,15</td><td>2,6</td><td colspan="2">3,0</td><td>3,4</td><td>1,15</td><td colspan="2">9,5</td></tr>
<tr><td>8</td><td colspan="2">60</td><td colspan="2">0,75</td><td colspan="2">1,15</td><td>1,7</td><td>2,15</td><td colspan="2">2,7</td><td>3,1</td><td colspan="2">3,6</td><td>4,1</td><td>1,2</td><td colspan="2">9,0</td></tr>
<tr><td>9</td><td colspan="2">80</td><td></td><td colspan="2">0,9</td><td colspan="2">1,4</td><td>2,15</td><td>2,8</td><td colspan="2">3,4</td><td>4,0</td><td colspan="2">4,7</td><td>5,3</td><td>1,35</td><td colspan="2">8,0</td></tr>
<tr><td colspan="4">Индекс</td><td colspan="2">а</td><td colspan="2">б</td><td>в</td><td>г</td><td colspan="2">д</td><td>е</td><td colspan="2">ж</td><td>з</td><td colspan="4"></td></tr>
<tr><td colspan="20">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="5">Группы стали и предела прочности</td><td colspan="3">Группа стали</td><td colspan="8">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="7">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="3">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="2">свыше 0,74</td><td colspan="5">до 0,59 0,59 - 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="3" rowspan="3">0,8</td><td colspan="3"></td><td colspan="2" rowspan="3">1,25</td><td colspan="5" rowspan="3">1,1 1,2</td><td colspan="2" rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="2" rowspan="4">Числа одинаковых отверстий в одной детали</td><td colspan="3">Число отверстий</td><td colspan="6">до 3</td><td colspan="9">4 - 10 11 - 25</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="6"></td><td colspan="9" rowspan="3">0,9 0,85</td></tr>
<tr><td colspan="2">1,0</td><td colspan="4"></td></tr>
<tr><td colspan="6"></td></tr>
<tr><td colspan="2" rowspan="4">Жесткости детали или крепления</td><td colspan="3">Жесткость детали</td><td colspan="9">Деталь и установка жесткие</td><td colspan="6">Деталь неустойчивая или тонкостенная</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="9"></td><td colspan="6" rowspan="3">1,1</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7"></td></tr>
<tr><td colspan="9"></td></tr>
<tr><td colspan="2" rowspan="4">Характера обработки</td><td colspan="3">Обработка</td><td colspan="9">Под зенкерование и расточку резцом</td><td colspan="6">Под развертывание и нарезание резьбы метчиком</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="9"></td><td colspan="6" rowspan="3">1,3</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7"></td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="9%"><col width="4%"><col width="6%"><col width="7%"></colgroup>
<tr><td colspan="14">Неполное штучное время Развертывание отверстий, Rz 20 - Ra 2,5, 1Т9 - 1Т8 квалитет Ra 2,5 - Ra 1,25, 1Т7 квалитет</td><td colspan="4">Горизонтально-расточные станки</td></tr>
<tr><td colspan="14">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="4">Развертки из стали Р6М5</td></tr>
<tr><td colspan="14">Единичное и мелкосерийное производство</td><td colspan="2">Карта 90</td><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Параметр шероховатости, квалитет</td><td rowspan="2">Диаметр обрабатываемого отверстия</td><td colspan="11">Длина обрабатываемого отверстия l, мм, до</td><td colspan="4">Режимы резания</td></tr>
<tr><td>10</td><td>20</td><td>30</td><td>40</td><td>50</td><td>75</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>S , о</td><td colspan="2" rowspan="2">v, м/мин.</td><td>N , р</td></tr>
<tr><td>D, мм, до</td><td colspan="11">Время на проход, мин.</td><td>мм/об.</td><td>кВт, до</td></tr>
<tr><td>1</td><td>Обработка одной</td><td>10</td><td>0,4</td><td>0,45</td><td>0,5</td><td>0,55</td><td>0,65</td><td>0,7</td><td>0,85</td><td>1,0</td><td>1,1</td><td>1,25</td><td>1,35</td><td>0,7</td><td colspan="2">9,4</td><td rowspan="10">До 1</td></tr>
<tr><td>2</td><td>разверткой Rz 20</td><td>15</td><td>0,5</td><td>0,55</td><td>0,60</td><td>0,70</td><td>0,75</td><td>1,0</td><td>1,1</td><td>1,2</td><td>1,4</td><td>1,35</td><td>1,8</td><td>0,8</td><td colspan="2">9,4</td></tr>
<tr><td>3</td><td>- Ra 2,5, 1Т9 - 1Т8</td><td>20</td><td>0,55</td><td>0,65</td><td>0,7</td><td>0,8</td><td>0,9</td><td>1,05</td><td>1,25</td><td>1,45</td><td>1,65</td><td>1,9</td><td>2,1</td><td>0,8</td><td colspan="2">10,0</td></tr>
<tr><td>4</td><td rowspan="7">квалитет</td><td>25</td><td>0,6</td><td>0,7</td><td>0,75</td><td>0,85</td><td>0,97</td><td>1,15</td><td>1,4</td><td>1,65</td><td>1,85</td><td>2,1</td><td>2,35</td><td>0,9</td><td colspan="2">9,7</td></tr>
<tr><td>5</td><td>30</td><td>0,65</td><td>0,75</td><td>0,9</td><td>1,0</td><td>1,1</td><td>1,35</td><td>1,65</td><td>1,95</td><td>2,25</td><td>2,6</td><td>2,9</td><td>1,0</td><td colspan="2">8,5</td></tr>
<tr><td>6</td><td>35</td><td>0,75</td><td>0,85</td><td>1,0</td><td>1,15</td><td>1,3</td><td>1,6</td><td>2,0</td><td>2,3</td><td>2,7</td><td>3,0</td><td>3,4</td><td>1,0</td><td colspan="2">8,3</td></tr>
<tr><td>7</td><td>40</td><td>0,85</td><td>1,0</td><td>1,15</td><td>1,3</td><td>1,5</td><td>1,8</td><td>2,2</td><td>2,6</td><td>3,0</td><td>3,4</td><td>3,8</td><td>1,2</td><td colspan="2">6,9</td></tr>
<tr><td>8</td><td>50</td><td>1,0</td><td>1,15</td><td>1,3</td><td>1,5</td><td>1,7</td><td>2,1</td><td>2,6</td><td>3,0</td><td>3,5</td><td>4,0</td><td>4,5</td><td>1,4</td><td colspan="2">6,3</td></tr>
<tr><td>9</td><td>60</td><td>1,2</td><td>1,4</td><td>1,6</td><td>1,8</td><td>2,1</td><td>2,5</td><td>3,1</td><td>3,7</td><td>4,3</td><td>5,0</td><td>5,5</td><td>1,5</td><td colspan="2">5,6</td></tr>
<tr><td>10</td><td>80</td><td>1,4</td><td>1,6</td><td>1,9</td><td>2,2</td><td>2,5</td><td>3,0</td><td>3,8</td><td>4,5</td><td>5,0</td><td>6,0</td><td>6,5</td><td>1,7</td><td colspan="2">5,4</td></tr>
<tr><td>11</td><td>Обработка двумя</td><td>10</td><td>1,05</td><td>1,25</td><td>1,45</td><td>1,65</td><td>1,9</td><td>2,3</td><td>2,8</td><td>3,3</td><td>3,9</td><td>4,5</td><td>5,0</td><td>0,8 - 0,5</td><td colspan="2">9,4 - 4,0</td><td rowspan="10">До 1</td></tr>
<tr><td>12</td><td>развертками Ra</td><td>15</td><td>1,3</td><td>1,4</td><td>1,7</td><td>1,9</td><td>2,2</td><td>2,6</td><td>3,2</td><td>3,8</td><td>4,4</td><td>5,0</td><td>6,0</td><td>0,9 - 0,6</td><td colspan="2">9,4 - 4,7</td></tr>
<tr><td>13</td><td>2,5 - Ra 1,25, 1Т7</td><td>20</td><td>1,5</td><td>1,8</td><td>2,1</td><td>2,4</td><td>2,7</td><td>3,3</td><td>4,0</td><td>4,8</td><td>5,5</td><td>6,5</td><td>7,0</td><td>1,0 - 0,7</td><td colspan="2">10 - 4,0</td></tr>
<tr><td>14</td><td rowspan="7">квалитет</td><td>25</td><td>1,7</td><td>1,9</td><td>2,3</td><td>2,6</td><td>3,0</td><td>3,5</td><td>4,5</td><td>5,5</td><td>6,0</td><td>7,0</td><td>8,0</td><td>1,1 - 0,8</td><td colspan="2">9,7 - 4,0</td></tr>
<tr><td>15</td><td>30</td><td>1,8</td><td>2,0</td><td>2,5</td><td>2,9</td><td>3,3</td><td>4,0</td><td>5,0</td><td>6,0</td><td>7,0</td><td>8,0</td><td>9,0</td><td>1,2 - 0,9</td><td colspan="2">8,5 - 3,8</td></tr>
<tr><td>16</td><td>35</td><td>2,0</td><td>2,3</td><td>2,7</td><td>3,1</td><td>3,6</td><td>4,5</td><td>5,5</td><td>6,5</td><td>7,5</td><td>9,0</td><td>10,0</td><td>1,3 - 0,9</td><td colspan="2">8,3 - 4,0</td></tr>
<tr><td>17</td><td>40</td><td>2,2</td><td>2,5</td><td>3,0</td><td>3,5</td><td>4,0</td><td>5,0</td><td>6,0</td><td>7,5</td><td>8,5</td><td>9,5</td><td>11,0</td><td>1,4 - 1,0</td><td colspan="2">6,9 - 4,0</td></tr>
<tr><td>18</td><td>50</td><td>2,5</td><td>2,9</td><td>3,4</td><td>4,0</td><td>4,5</td><td>5,5</td><td>7,0</td><td>8,0</td><td>9,5</td><td>11</td><td>12,5</td><td>1,5 - 1,2</td><td colspan="2">6,3 - 4,0</td></tr>
<tr><td>19</td><td>60</td><td>2,7</td><td>3,1</td><td>3,7</td><td>4,3</td><td>4,8</td><td>6,0</td><td>7,5</td><td>9,0</td><td>10</td><td>11,5</td><td>13</td><td>1,7 - 1,4</td><td colspan="2">5,6 - 4,0</td></tr>
<tr><td>20</td><td>80</td><td>2,9</td><td>3,4</td><td>4,0</td><td>4,7</td><td>5,5</td><td>6,5</td><td>8,0</td><td>9,5</td><td>11,5</td><td>13</td><td>14,5</td><td>2,0 - 1,5</td><td colspan="2">5,4 - 4,5</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="13%"><col width="17%"><col width="6%"><col width="8%"><col width="5%"><col width="2%"><col width="6%"><col width="8%"><col width="6%"><col width="4%"><col width="2%"><col width="6%"><col width="7%"><col width="6%"><col width="7%"></colgroup>
<tr><td colspan="10">Неполное штучное время Развертывание отверстий, Rz 20 - Ra 2,5, 1Т9 - 1Т8 квалитет Ra 2,5 - Ra 1,25, 1Т7 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="10">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Развертки из стали Р6М5</td></tr>
<tr><td colspan="10">Единичное и мелкосерийное производство</td><td colspan="5">Карта 90 Лист 2</td></tr>
<tr><td colspan="15">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td>Группы стали, предела прочности и</td><td>Группа стали</td><td colspan="6">Углеродистые, хромистые, никелевые</td><td colspan="7">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td rowspan="5">продолжительности обработки</td><td>Предел прочности стали сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td colspan="2">свыше 0,74</td><td colspan="3">до 0,59</td><td colspan="2">0,59 - 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td>Продолжительность обработки, мин.</td><td>до 10</td><td>свыше 10</td><td colspan="2">-</td><td>до 10</td><td>свыше 10</td><td>до 10</td><td colspan="2">свыше 10</td><td>до 10</td><td>свыше 10</td><td>до 10</td><td>свыше 10</td></tr>
<tr><td rowspan="3">Коэффициент</td><td rowspan="3">0,9</td><td rowspan="3">0,8</td><td colspan="2"></td><td rowspan="3">1,1</td><td rowspan="3">1,25</td><td></td><td colspan="2" rowspan="3">1,1</td><td rowspan="3">1,1</td><td rowspan="3">1,2</td><td rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td></td><td>1,0</td></tr>
</table>


<a id="p102837"></a>*Примечание.* Большие скорости и подачи даны для чернового прохода.


<table>
<colgroup><col width="6%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="8%"></colgroup>
<tr><td colspan="19">Неполное штучное время Горизонтально-расточные станки Сверление отверстий</td></tr>
<tr><td colspan="19">Медные сплавы, НВ = 0,98 - 1,37 ГПа и алюминиевые Сверла спиральные Р6М5 Единичное и мелкосерийное производство</td></tr>
<tr><td colspan="17">Карта 91</td><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Диаметр обрабатываемого отверстия</td><td colspan="14">Длина обрабатываемой поверхности l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td>10</td><td>20</td><td>30</td><td>40</td><td>50</td><td>60</td><td>80</td><td>100</td><td>125</td><td>150</td><td>175</td><td>200</td><td>225</td><td>250</td><td>S , о</td><td rowspan="2">v, м/мин.</td><td>N , р</td></tr>
<tr><td>D, мм, до</td><td colspan="14">Время на проход, мин.</td><td>мм/об.</td><td>кВт, до</td></tr>
<tr><td>1</td><td>8</td><td>0,44</td><td>0,45</td><td>0,47</td><td>0,49</td><td>0,51</td><td>0,53</td><td>0,63</td><td>0,67</td><td>0,8</td><td>1,23</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,4 --- 0,3</td><td>38 -- 20</td><td rowspan="3">1,0</td></tr>
<tr><td>2</td><td>10</td><td>0,44</td><td>0,47</td><td>0,48</td><td>0,49</td><td>0,51</td><td>0,53</td><td>0,63</td><td>0,67</td><td>0,8</td><td>1,26</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,5 --- 0,4</td><td>38 -- 19</td></tr>
<tr><td>3</td><td>13</td><td>0,44</td><td>0,47</td><td>0,48</td><td>0,5</td><td>0,5</td><td>0,53</td><td>0,64</td><td>0,78</td><td>0,82</td><td>1,3</td><td>-</td><td>-</td><td>-</td><td>-</td><td>0,6 ---- 0,45</td><td>39 -- 20</td></tr>
<tr><td>4</td><td>16</td><td>0,45</td><td>0,47</td><td>0,49</td><td>0,5</td><td>0,52</td><td>0,75</td><td>0,9</td><td>1,0</td><td>1,25</td><td>1,4</td><td>1,54</td><td>-</td><td>-</td><td>-</td><td>0,7 --- 0,5</td><td>38 -- 20</td><td>1,8</td></tr>
<tr><td>5</td><td>20</td><td>0,45</td><td>0,47</td><td>0,5</td><td>0,52</td><td>0,54</td><td>0,56</td><td>0,92</td><td>1,1</td><td>1,25</td><td>1,42</td><td>1,68</td><td>1,83</td><td>2,6</td><td>2,7</td><td>0,8 --- 0,6</td><td>38 -- 20</td><td>2,0</td></tr>
<tr><td>6</td><td>25</td><td>0,46</td><td>0,48</td><td>0,51</td><td>0,53</td><td>0,56</td><td>0,59</td><td>0,68</td><td>1,2</td><td>1,37</td><td>1,56</td><td>1,85</td><td>2,2</td><td>2,7</td><td>2,9</td><td>0,9 ---- 0,65</td><td>36 -- 20</td><td>2,6</td></tr>
<tr><td>7</td><td>30</td><td>0,47</td><td>0,49</td><td>0,52</td><td>0,54</td><td>0,57</td><td>0,4</td><td>0,69</td><td>1,3</td><td>1,45</td><td>1,95</td><td>1,95</td><td>2,3</td><td>2,7</td><td>2,9</td><td>1,0 ---- 0,75</td><td>37 -- 19</td><td>3,5</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="22%"><col width="29%"><col width="5%"><col width="10%"><col width="4%"><col width="8%"><col width="5%"><col width="16%"></colgroup>
<tr><td colspan="4">Неполное штучное время Сверление отверстий</td><td colspan="4">Горизонтально-расточные станки</td></tr>
<tr><td colspan="4" rowspan="2">Медные сплавы, НВ = 0,98 - 1,37 ГПа и алюминиевые Единичное и мелкосерийное производство</td><td colspan="4">Сверла спиральные Р6М5</td></tr>
<tr><td colspan="3">Карта 91</td><td>Лист 2</td></tr>
<tr><td colspan="8">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td>Группы медных сплавов и</td><td>Группа сплавов</td><td colspan="6">Гомогенные Гетерогенные</td></tr>
<tr><td rowspan="4">твердости</td><td>Твердость НВ, ГПа</td><td colspan="6">0,59 - 0,74 0,98 - 1,37 1,47 - 2,15</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="6"></td></tr>
<tr><td colspan="2">0,7</td><td>1,0</td><td colspan="3">1,1</td></tr>
<tr><td colspan="6"></td></tr>
<tr><td rowspan="3">Группы алюминиевых сплавов и твердости</td><td>Группа сплавов</td><td colspan="6">Силумин и литейные сплавы Дюралюминий</td></tr>
<tr><td>Твердость НВ, ГПа</td><td colspan="6">до 0,64 до 0,98</td></tr>
<tr><td>Коэффициент</td><td colspan="6">0,75 0,7</td></tr>
<tr><td rowspan="4">Число одинаковых отверстий в одной детали</td><td>Число одинаковых отверстий</td><td colspan="5">до 3 4 - 10</td><td>11 - 25</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="5"></td><td rowspan="3">0,85</td></tr>
<tr><td>1,0</td><td colspan="4">0,9</td></tr>
<tr><td colspan="5"></td></tr>
<tr><td rowspan="4">Жесткости детали или крепления</td><td>Жесткость детали</td><td colspan="4">Деталь и установка жесткие</td><td colspan="2">Неустойчивые или тонкостенные детали</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="2" rowspan="3">1,1</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td rowspan="4">Характера обработки</td><td>Обработка</td><td colspan="4">Под зенкерование и расточку резцом</td><td colspan="2">Под развертывание и нарезание резьбы</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="2" rowspan="3">1,3</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
</table>


<a id="p102862"></a>*Примечание.* Меньшие величины скоростей и подач приведены для отверстий длиной более 3D.


<table>
<colgroup><col width="6%"><col width="12%"><col width="7%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="4%"><col width="4%"><col width="5%"><col width="7%"><col width="7%"><col width="9%"></colgroup>
<tr><td colspan="11">Неполное штучное время Нарезание резьбы метчиками</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="11">Зенкование отверстий (снятие фасок) Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Сверла, зенковки из стали Р6М5, метчики из стали 9ХГС</td></tr>
<tr><td colspan="11">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="3">Карта 92</td><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр нарезаемой</td><td>Шаг резьбы</td><td colspan="10">Длина нарезаемой резьбы l, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td rowspan="2">резьбы D, мм</td><td rowspan="2">Р, мм</td><td>10</td><td>15</td><td>20</td><td>25</td><td>30</td><td>40</td><td>50</td><td>60</td><td>75</td><td>100</td><td>S , о</td><td rowspan="2">v, м/мин.</td><td>N , р</td></tr>
<tr><td colspan="10">Время на проход, мин.</td><td>мм/об.</td><td>кВт, до</td></tr>
<tr><td>1</td><td rowspan="2">10</td><td>1,0</td><td>1,5</td><td>1,65</td><td>1,7</td><td>1,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,0</td><td rowspan="2">1,9</td><td rowspan="16">До 1</td></tr>
<tr><td>2</td><td>1,5</td><td>1,45</td><td>1,6</td><td>1,65</td><td>1,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,5</td></tr>
<tr><td>3</td><td rowspan="2">12</td><td>1,25</td><td>1,45</td><td>1,6</td><td>1,65</td><td>1,75</td><td>1,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,25</td><td rowspan="2">2,3</td></tr>
<tr><td>4</td><td>1,75</td><td>1,4</td><td>1,5</td><td>1,6</td><td>1,65</td><td>1,7</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,75</td></tr>
<tr><td>5</td><td rowspan="2">16</td><td>1,5</td><td>1,5</td><td>1,6</td><td>1,7</td><td>1,75</td><td>1,85</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,5</td><td rowspan="2">2,5</td></tr>
<tr><td>6</td><td>2,0</td><td>1,45</td><td>1,55</td><td>1,6</td><td>1,65</td><td>1,75</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>2,0</td></tr>
<tr><td>7</td><td rowspan="2">20</td><td>1,5</td><td>1,5</td><td>1,6</td><td>1,65</td><td>1,75</td><td>1,85</td><td>1,95</td><td>-</td><td>-</td><td>-</td><td>-</td><td>1,5</td><td rowspan="2">3,1</td></tr>
<tr><td>8</td><td>2,5</td><td>1,45</td><td>1,5</td><td>1,55</td><td>1,6</td><td>1,65</td><td>1,75</td><td>-</td><td>-</td><td>-</td><td>-</td><td>2,5</td></tr>
<tr><td>9</td><td rowspan="2">24</td><td>2,0</td><td>1,5</td><td>1,6</td><td>1,7</td><td>1,75</td><td>1,8</td><td>1,95</td><td>2,1</td><td>-</td><td>-</td><td>-</td><td>2,0</td><td rowspan="2">3,1</td></tr>
<tr><td>10</td><td>3,0</td><td>1,45</td><td>1,5</td><td>1,6</td><td>1,65</td><td>1,7</td><td>1,75</td><td>1,85</td><td>-</td><td>-</td><td>-</td><td>3,0</td></tr>
<tr><td>11</td><td rowspan="2">30</td><td>2,0</td><td>1,55</td><td>1,7</td><td>1,8</td><td>1,85</td><td>1,95</td><td>2,1</td><td>2,3</td><td>2,5</td><td>-</td><td>-</td><td>2,0</td><td rowspan="2">2,9</td></tr>
<tr><td>12</td><td>3,5</td><td>1,5</td><td>1,6</td><td>1,65</td><td>1,7</td><td>1,75</td><td>1,85</td><td>1,95</td><td>2,1</td><td>-</td><td>-</td><td>3,5</td></tr>
<tr><td>13</td><td rowspan="2">36</td><td>3,0</td><td>1,55</td><td>1,6</td><td>1,7</td><td>1,75</td><td>1,8</td><td>1,9</td><td>2,0</td><td>2,1</td><td>2,3</td><td>-</td><td>3,0</td><td rowspan="2">3,5</td></tr>
<tr><td>14</td><td>4,0</td><td>1,5</td><td>1,55</td><td>1,65</td><td>1,7</td><td>1,75</td><td>1,8</td><td>1,9</td><td>2,0</td><td>2,1</td><td>-</td><td>4,0</td></tr>
<tr><td>15</td><td rowspan="2">48</td><td>3,0</td><td>1,6</td><td>1,7</td><td>1,75</td><td>1,85</td><td>1,9</td><td>2,0</td><td>2,2</td><td>2,3</td><td>2,5</td><td>2,8</td><td>3,0</td><td rowspan="2">3,8</td></tr>
<tr><td>16</td><td>5,0</td><td>1,55</td><td>1,6</td><td>1,65</td><td>1,7</td><td>1,75</td><td>1,85</td><td>1,9</td><td>2,0</td><td>2,1</td><td>2,3</td><td>5,0</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td><td>к</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="26%"><col width="23%"><col width="5%"><col width="13%"><col width="3%"><col width="4%"><col width="11%"><col width="15%"></colgroup>
<tr><td colspan="4">Неполное штучное время Нарезание резьбы метчиками</td><td colspan="4">Горизонтально-расточные станки</td></tr>
<tr><td colspan="4">Зенкование отверстий (снятие фасок) Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="4">Сверла, зенковки из стали Р6М5, метчики из стали 9ХГС</td></tr>
<tr><td colspan="4">Чугун серый, НВ = 1,76 - 2,15 ГПа Единичное и мелкосерийное производство</td><td colspan="4">Карта 92 Лист 2</td></tr>
<tr><td colspan="8">Зенкование отверстий (снятие фасок)</td></tr>
<tr><td colspan="8">Ширина фаски, мм, до</td></tr>
<tr><td>0,5</td><td>1,0</td><td colspan="3">2,0</td><td colspan="3">3,0</td></tr>
<tr><td colspan="8">Неполное штучное время, мин.</td></tr>
<tr><td>0,25</td><td>04</td><td colspan="3">0,35</td><td colspan="3">0,45</td></tr>
<tr><td colspan="8">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="4">Числа одинаковых отверстий в одной детали</td><td>Число отверстий</td><td colspan="3">до 3</td><td colspan="2">4 - 10</td><td>11 - 25</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="3"></td><td colspan="2" rowspan="3">0,9</td><td rowspan="3">0,85</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td rowspan="4">Характера обработки</td><td>Нарезание резьбы</td><td colspan="4">На проход</td><td colspan="2">В упор</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="2" rowspan="3">1,1</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
</table>


<a id="p102893"></a>*Примечание.* При нарезании резьбы в 2 прохода для диаметров свыше 16 мм время по карте удваивается.


<table>
<colgroup><col width="8%"><col width="32%"><col width="16%"><col width="14%"><col width="15%"><col width="15%"></colgroup>
<tr><td colspan="3">Подготовительно-заключительное время на партию деталей</td><td colspan="3">Горизонтально-расточные станки</td></tr>
<tr><td colspan="3">Время на обслуживание рабочего места, отдых и личные потребности Среднесерийное производство</td><td colspan="3">Карта 93</td></tr>
<tr><td colspan="6">I. На наладку станка, инструмента и приспособлений</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Вид обработки и наладки</td><td rowspan="3">Число переходов и операций, до</td><td colspan="3">Диаметр шпинделя станка, мм, до</td></tr>
<tr><td>65</td><td>110</td><td>160</td></tr>
<tr><td colspan="3">Время, мин.</td></tr>
<tr><td>1</td><td rowspan="3">Обработка отверстий, торцов и плоскостей</td><td>15</td><td>17</td><td>19</td><td>22</td></tr>
<tr><td>2</td><td>30</td><td>23</td><td>25</td><td>28</td></tr>
<tr><td>3</td><td>свыше 30</td><td>29</td><td>31</td><td>34</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td></tr>
<tr><td colspan="6">II. На получение инструмента и приспособлений до начала и сдачу их после окончания обработки</td></tr>
<tr><td>4</td><td colspan="2">Получение инструмента и приспособлений исполнителем работы до начала и сдача их после окончания обработки партии деталей</td><td colspan="3">7 - 10</td></tr>
<tr><td colspan="6">III. Добавлять ко времени на наладку станка</td></tr>
<tr><td>5</td><td colspan="2">При обработке торцевых плоскостей с резцедержателем на планшайбе с установкой резцедержателя</td><td>4,0</td><td>5,0</td><td>6,0</td></tr>
<tr><td>6</td><td colspan="2">При обработке с угольником с его установкой</td><td>6,0</td><td>6,0</td><td>7,5</td></tr>
<tr><td>7</td><td colspan="2">При обработке под углом с поворотом стола</td><td>1,5</td><td>2,0</td><td>2,5</td></tr>
<tr><td>8</td><td colspan="2">При установке зажимного приспособления на стол станка подъемником</td><td>3,0</td><td>3,0</td><td>3,0</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td></tr>
<tr><td colspan="6">IV. Время на обслуживание рабочего места</td></tr>
<tr><td rowspan="2">9</td><td colspan="2">Группа станков: диаметр шпинделя, мм</td><td>65</td><td>110</td><td>160</td></tr>
<tr><td colspan="2">Время в % от оперативного</td><td>4,0</td><td>4,5</td><td>5,5</td></tr>
<tr><td colspan="3">Индекс</td><td>а</td><td>б</td><td>в</td></tr>
<tr><td colspan="3">V. Время на отдых и личные потребности в % от оперативного</td><td colspan="3">4</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="7%"><col width="5%"><col width="8%"><col width="11%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="3%"><col width="2%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"><col width="4%"></colgroup>
<tr><td colspan="14" rowspan="2">Вспомогательное время на заготовку и снятие детали Среднесерийное производство</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="7">Карта 94</td></tr>
<tr><td rowspan="4">N позиции</td><td rowspan="4">Способ установки детали</td><td colspan="2" rowspan="4">Состояние установочной поверхности</td><td colspan="2" rowspan="4">Характер выверки</td><td colspan="3">Вручную</td><td colspan="6">Подъемником при станке</td><td colspan="6">Мостовым краном</td></tr>
<tr><td>8</td><td>12</td><td>20</td><td>30</td><td>80</td><td>200</td><td>500</td><td colspan="2">1000</td><td>30</td><td>80</td><td>200</td><td>500</td><td>1000</td><td>2000</td></tr>
<tr><td colspan="15">Масса детали, кг, до</td></tr>
<tr><td colspan="15">Время, мин.</td></tr>
<tr><td>1</td><td rowspan="2">На столе с креплением болтами и</td><td colspan="2" rowspan="4">Необработанная</td><td colspan="2">Без выверки</td><td>1,1</td><td>1,3</td><td>1,5</td><td>2,9</td><td>3,5</td><td>4,2</td><td>5,1</td><td colspan="2">5,8</td><td>4,4</td><td>5,0</td><td>5,7</td><td>6,6</td><td>7,3</td><td>8,2</td></tr>
<tr><td>2</td><td colspan="2">С выверкой по контуру</td><td>2,2</td><td>2,3</td><td>2,5</td><td>3,7</td><td>4,8</td><td>6,3</td><td>8,1</td><td colspan="2">9,8</td><td>5,2</td><td>6,3</td><td>7,8</td><td>9,6</td><td>11,3</td><td>13,4</td></tr>
<tr><td>3</td><td rowspan="4">планками</td><td rowspan="2">По разметочной риске</td><td>Детали цилиндрической формы</td><td>3,1</td><td>3,3</td><td>3,7</td><td>4,8</td><td>6,2</td><td>8,0</td><td>10,0</td><td colspan="2">12,0</td><td>6,3</td><td>7,7</td><td>9,4</td><td>11,5</td><td>13,5</td><td>16,0</td></tr>
<tr><td>4</td><td>Детали фасонной или коробчатой формы</td><td>3,8</td><td>4,2</td><td>4,7</td><td>6,5</td><td>8,4</td><td>10,7</td><td>-</td><td colspan="2">-</td><td>8,0</td><td>10,0</td><td>12,2</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>5</td><td colspan="2" rowspan="2">Обработанная</td><td colspan="2">Без выверки</td><td>1,1</td><td>1,3</td><td>1,5</td><td>2,9</td><td>3,5</td><td>4,2</td><td>5,1</td><td colspan="2">5,8</td><td>4,4</td><td>5,0</td><td>5,7</td><td>6,6</td><td>7,3</td><td>8,2</td></tr>
<tr><td>6</td><td colspan="2">С выверкой рейсмусом</td><td>2,2</td><td>2,3</td><td>2,5</td><td>3,6</td><td>4,9</td><td>6,5</td><td>8,8</td><td colspan="2">11,0</td><td>5,1</td><td>6,4</td><td>8,0</td><td>10,3</td><td>12,4</td><td>14,5</td></tr>
<tr><td>7</td><td rowspan="5">На угольнике с креплением болтами и планками</td><td rowspan="5">Обработанная</td><td rowspan="2">На опоре</td><td rowspan="2">С выверкой</td><td>По необработанной поверхности</td><td>1,1</td><td>1,3</td><td>1,4</td><td>3,0</td><td>3,7</td><td>-</td><td>-</td><td colspan="2">-</td><td>4,5</td><td>5,2</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>8</td><td>По разметочной риске</td><td>1,2</td><td>1,4</td><td>1,8</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>9</td><td rowspan="3">На весу</td><td colspan="2">Без выверки по фиксатору или направляющей</td><td>0,9</td><td>1,0</td><td>1,1</td><td>2,3</td><td>2,9</td><td>-</td><td>-</td><td colspan="2">-</td><td>3,8</td><td>4,4</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td rowspan="2">С выверкой</td><td>По контуру необработанной поверхности</td><td>1,3</td><td>1,5</td><td>1,8</td><td>3,5</td><td>4,1</td><td>-</td><td>-</td><td colspan="2">-</td><td>5,0</td><td>5,6</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>11</td><td>По разметочной риске</td><td>1,6</td><td>1,8</td><td>2,1</td><td>3,8</td><td>4,6</td><td>-</td><td>-</td><td colspan="2">-</td><td>5,3</td><td>6,1</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td></td><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td colspan="2">з</td><td>и</td><td>к</td><td>л</td><td>м</td><td>н</td><td>о</td></tr>
</table>


<a id="p102928"></a>*Примечание.* Время по карте дано на крепление и открепление детали двумя болтами. В случае крепления детали большим числом болтов на каждый последующий болт ко времени добавлять 0,4 мин.


<table>
<colgroup><col width="5%"><col width="14%"><col width="24%"><col width="20%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="10">Вспомогательное время на кантовку крупных деталей Кантовка и перемещение и время на перемещение детали к станку при детали подъемником установке подъемником</td></tr>
<tr><td colspan="10">Среднесерийное производство Карта 95</td></tr>
<tr><td rowspan="3">N позиции</td><td>Угол поворота</td><td rowspan="3">Характер застропки</td><td>Расстояние до места</td><td colspan="6">Масса детали при кантовке</td></tr>
<tr><td>при кантовке,</td><td>расположения или места</td><td>80</td><td>200</td><td>500</td><td>1000</td><td>2000</td><td>3000</td></tr>
<tr><td>градус</td><td>кантовки детали, м, до</td><td colspan="6">Время, мин.</td></tr>
<tr><td>1</td><td rowspan="3">90</td><td>Удобная застропка при наличии у</td><td>5</td><td>0,9</td><td>1,1</td><td>1,4</td><td>1,9</td><td>2,6</td><td>3,0</td></tr>
<tr><td>2</td><td>деталей просветов и выступов для</td><td>10</td><td>1,2</td><td>1,4</td><td>1,7</td><td>2,3</td><td>3,1</td><td>3,7</td></tr>
<tr><td>3</td><td rowspan="4">захвата стропами</td><td>20</td><td>1,4</td><td>1,7</td><td>2,1</td><td>2,9</td><td>3,9</td><td>4,6</td></tr>
<tr><td>4</td><td rowspan="3">180</td><td>5</td><td>1,4</td><td>1,7</td><td>2,1</td><td>2,8</td><td>3,8</td><td>4,5</td></tr>
<tr><td>5</td><td>10</td><td>1,6</td><td>2,0</td><td>2,5</td><td>3,2</td><td>4,3</td><td>5,3</td></tr>
<tr><td>6</td><td>20</td><td>1,8</td><td>2,3</td><td>2,8</td><td>3,8</td><td>5,0</td><td>6,0</td></tr>
<tr><td>7</td><td rowspan="3">90</td><td>Неудобная застропка на</td><td>5</td><td>2,2</td><td>2,7</td><td>3,3</td><td>4,4</td><td>5,9</td><td>6,9</td></tr>
<tr><td>8</td><td>сплошных деталях с захватом</td><td>10</td><td>2,4</td><td>3,0</td><td>3,7</td><td>4,9</td><td>6,5</td><td>7,6</td></tr>
<tr><td>9</td><td rowspan="4">снаружи петлей</td><td>20</td><td>2,8</td><td>3,4</td><td>4,2</td><td>5,5</td><td>7,2</td><td>8,5</td></tr>
<tr><td>10</td><td rowspan="3">180</td><td>5</td><td>2,9</td><td>3,7</td><td>4,7</td><td>6,7</td><td>9,2</td><td>11,0</td></tr>
<tr><td>11</td><td>10</td><td>3,0</td><td>3,9</td><td>5,1</td><td>7,2</td><td>9,8</td><td>11,8</td></tr>
<tr><td>12</td><td>20</td><td>3,3</td><td>4,2</td><td>5,4</td><td>7,8</td><td>10,6</td><td>12,7</td></tr>
<tr><td>13</td><td colspan="2">Транспортировка детали подъемником (к станку при</td><td>10</td><td colspan="3">0,25</td><td colspan="3">0,35</td></tr>
<tr><td>14</td><td colspan="2">установке и от станка при снятии) на расстояние более 5 м при длине перемещения</td><td>20</td><td colspan="3">0,45</td><td colspan="3">0,55</td></tr>
<tr><td></td><td colspan="2">Индекс</td><td></td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td></tr>
</table>


<a id="p102946"></a>Примечания: 1. Время на кантовку добавляется ко времени на установку и снятие детали в тех случаях, когда в процессе выполнения операции имеет место переустановка детали.
2. <a id="p102947"></a>Время на транспортировку детали добавляется ко времени на установку и снятие детали в тех случаях, когда детали находятся на расстоянии более 5 м от станка.


<table>
<colgroup><col width="4%"><col width="13%"><col width="16%"><col width="12%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="14">Вспомогательное время, связанное с переходом Горизонтально-расточные станки Среднесерийное производство</td></tr>
<tr><td colspan="11">Карта 96</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="5">N позиции</td><td>База для совмещения</td><td>Способ совмещения и</td><td>Перемещение шпинделя и</td><td rowspan="5">Точность межцентрового расстояния, мм, до</td><td colspan="9">Диаметр шпинделя, мм, до</td></tr>
<tr><td rowspan="4">оси шпинделя с осью обрабатываемого отверстия</td><td rowspan="4">изменения</td><td rowspan="4">стола в плоскостях</td><td colspan="3">65</td><td colspan="3">110</td><td colspan="3">160</td></tr>
<tr><td colspan="9">Длина перемещения частей стыка, мм, до</td></tr>
<tr><td>300</td><td>600</td><td>1000</td><td>300</td><td>600</td><td>1000</td><td>300</td><td>600</td><td>1000</td></tr>
<tr><td colspan="9">Время, мин.</td></tr>
<tr><td colspan="14">Время на совмещение оси шпинделя с осью обрабатываемого отверстия</td></tr>
<tr><td>1</td><td rowspan="4">Отверстие кондуктора</td><td rowspan="2">По индикатору</td><td>Одной</td><td rowspan="2">-</td><td>3,0</td><td>3,2</td><td>3,4</td><td>3,8</td><td>4,0</td><td>4,2</td><td>4,4</td><td>4,6</td><td>4,9</td></tr>
<tr><td>2</td><td>Двух</td><td>3,9</td><td>4,2</td><td>4,4</td><td>4,9</td><td>5,2</td><td>5,5</td><td>5,7</td><td>6,0</td><td>6,3</td></tr>
<tr><td>3</td><td rowspan="2">По кондукторной втулке и контрольной оправе</td><td>Одной</td><td rowspan="2">-</td><td>1,6</td><td>1,8</td><td>2,0</td><td>1,9</td><td>2,1</td><td>2,3</td><td>2,2</td><td>2,4</td><td>2,6</td></tr>
<tr><td>4</td><td>Двух</td><td>2,2</td><td>2,5</td><td>2,7</td><td>2,6</td><td>2,9</td><td>3,2</td><td>2,9</td><td>3,3</td><td>3,6</td></tr>
<tr><td>5</td><td rowspan="2">Борштанга, установленная в кондукторе на опорах</td><td>Соединения шпинделя станка</td><td>Одной</td><td rowspan="2">-</td><td>0,4</td><td>0,6</td><td>-</td><td>0,5</td><td>0,7</td><td>-</td><td>0,6</td><td>0,8</td><td>-</td></tr>
<tr><td>6</td><td>с борштангой</td><td>Двух</td><td>0,55</td><td>0,8</td><td>-</td><td>0,6</td><td>0,9</td><td>-</td><td>0,8</td><td>1,15</td><td>-</td></tr>
<tr><td>7</td><td>Размеченная окружность</td><td>Иглой в шпинделе по</td><td>Одной</td><td rowspan="2">1,0</td><td>1,7</td><td>1,9</td><td>2,0</td><td>2,0</td><td>2,3</td><td>2,5</td><td>2,5</td><td>2,7</td><td>2,9</td></tr>
<tr><td>8</td><td>необработанного отверстия</td><td>размеченной окружности</td><td>Двух</td><td>2,1</td><td>2,5</td><td>2,8</td><td>2,6</td><td>3,1</td><td>3,5</td><td>3,1</td><td>3,6</td><td>4,1</td></tr>
<tr><td>9</td><td rowspan="6">Обработанное отверстие</td><td>По нониусной или масштабной</td><td>Одной</td><td rowspan="2">0,3</td><td>1,15</td><td>1,4</td><td>1,6</td><td>1,4</td><td>1,7</td><td>2,0</td><td>1,6</td><td>2,0</td><td>2,3</td></tr>
<tr><td>10</td><td rowspan="3">линейке</td><td>Двух</td><td>1,75</td><td>2,0</td><td>2,3</td><td>2,2</td><td>2,5</td><td>2,8</td><td>2,5</td><td>2,9</td><td>3,3</td></tr>
<tr><td>11</td><td>Одной</td><td rowspan="2">1,0</td><td>0,33</td><td>0,5</td><td>0,75</td><td>0,38</td><td>0,6</td><td>0,85</td><td>0,48</td><td>0,75</td><td>1,05</td></tr>
<tr><td>12</td><td>Двух</td><td>0,4</td><td>0,7</td><td>1,0</td><td>0,47</td><td>0,8</td><td>1,25</td><td>0,55</td><td>0,9</td><td>1,3</td></tr>
<tr><td>13</td><td rowspan="2">По консольной оправке</td><td>Одной</td><td rowspan="2">-</td><td>0,33</td><td>0,5</td><td>0,75</td><td>0,38</td><td>0,6</td><td>0,85</td><td>0,48</td><td>0,75</td><td>1,05</td></tr>
<tr><td>14</td><td>Двух</td><td>0,4</td><td>0,7</td><td>1,0</td><td>0,47</td><td>0,8</td><td>1,25</td><td>0,55</td><td>0,9</td><td>1,3</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="13%"><col width="16%"><col width="12%"><col width="9%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="14">Вспомогательное время, связанное с переходом Горизонтально-расточные станки Среднесерийное производство</td></tr>
<tr><td colspan="11">Карта 96</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="5">N позиции</td><td>База для совмещения</td><td>Способ совмещения и</td><td>Перемещение шпинделя и</td><td rowspan="5">Точность межцентрового расстояния, мм, до</td><td colspan="9">Диаметр шпинделя, мм, до</td></tr>
<tr><td rowspan="4">оси шпинделя с осью обрабатываемого отверстия</td><td rowspan="4">изменения</td><td rowspan="4">стола в плоскостях</td><td colspan="3">65</td><td colspan="3">110</td><td colspan="3">160</td></tr>
<tr><td colspan="9">Длина перемещения частей стыка, мм, до</td></tr>
<tr><td>300</td><td>600</td><td>1000</td><td>300</td><td>600</td><td>1000</td><td>300</td><td>600</td><td>1000</td></tr>
<tr><td colspan="9">Время, мин.</td></tr>
<tr><td colspan="14">Время на совмещение оси шпинделя с осью обрабатываемого отверстия</td></tr>
<tr><td>15</td><td>Наружная боковая</td><td>По нониусной или масштабной</td><td>Одной</td><td rowspan="2">0,3</td><td>1,15</td><td>1,35</td><td>1,5</td><td>1,35</td><td>1,6</td><td>1,8</td><td>1,55</td><td>1,85</td><td>2,1</td></tr>
<tr><td>16</td><td rowspan="3">плоскость детали</td><td rowspan="3">линейке</td><td>Двух</td><td>1,7</td><td>2,0</td><td>2,3</td><td>2,0</td><td>2,4</td><td>2,7</td><td>2,3</td><td>2,8</td><td>3,1</td></tr>
<tr><td>17</td><td>Одной</td><td rowspan="2">1,0</td><td>0,33</td><td>0,5</td><td>0,75</td><td>0,38</td><td>0,6</td><td>0,85</td><td>0,48</td><td>0,75</td><td>1,0</td></tr>
<tr><td>18</td><td>Двух</td><td>0,4</td><td>0,7</td><td>1,0</td><td>0,47</td><td>0,8</td><td>1,15</td><td>0,55</td><td>0,9</td><td>1,3</td></tr>
<tr><td>19</td><td colspan="2">Повернуть стол на угол при совмещении осей в другой</td><td>90°</td><td>-</td><td colspan="3">1,1</td><td colspan="3">1,3</td><td colspan="3">1,7</td></tr>
<tr><td>20</td><td colspan="2">плоскости с откреплением и закреплением</td><td>180°</td><td>-</td><td colspan="3">1,7</td><td colspan="3">2,0</td><td colspan="3">2,4</td></tr>
<tr><td>21</td><td colspan="2" rowspan="2">Закрепить или открепить шпиндельную бабку</td><td>Рычагом</td><td>-</td><td colspan="3">0,06</td><td colspan="3">0,07</td><td colspan="3">0,08</td></tr>
<tr><td>22</td><td>Гайкой</td><td>-</td><td colspan="3">0,14</td><td colspan="3">0,19</td><td colspan="3">0,25</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td><td>з</td><td>и</td></tr>
</table>


<a id="p102978"></a>*Примечание.* При автоматическом совмещении осей по упорам время устанавливается по паспортным данным станка с прибавлением времени на включение подачи.


<table>
<colgroup><col width="5%"><col width="16%"><col width="8%"><col width="8%"><col width="10%"><col width="8%"><col width="6%"><col width="8%"><col width="11%"><col width="3%"><col width="8%"><col width="10%"></colgroup>
<tr><td colspan="7" rowspan="2">Вспомогательное время, связанное с переходом Среднесерийное производство</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="3">Карта 96</td><td colspan="2">Лист 3</td></tr>
<tr><td colspan="12">Время на проход, мин.</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="5" rowspan="3">Характер обработки. Способ установки инструмента на стружку</td><td colspan="2" rowspan="3">Измеряемый размер, мм, до</td><td colspan="4">Диаметр шпинделя, мм, до</td></tr>
<tr><td>65</td><td colspan="2">110</td><td>160</td></tr>
<tr><td colspan="4">Время, мин.</td></tr>
<tr><td>23</td><td rowspan="5">Растачивание отверстий</td><td colspan="4">резцом, установленным на размер по шаблону (черновой проход)</td><td colspan="2">-</td><td>0,46</td><td colspan="2">0,55</td><td>0,65</td></tr>
<tr><td>24</td><td colspan="4">резцом со взятием пробной стружки (предчистовой</td><td colspan="2">100</td><td>1,0</td><td colspan="2">1,2</td><td>1,4</td></tr>
<tr><td>25</td><td colspan="4" rowspan="2">проход) 1Т13 - 1Т11 (5 - 4 кл.)</td><td colspan="2">300</td><td>1,2</td><td colspan="2">1,5</td><td>1,65</td></tr>
<tr><td>26</td><td colspan="2">свыше 300</td><td>1,5</td><td colspan="2">1,8</td><td>2,0</td></tr>
<tr><td>27</td><td colspan="4">мерной расточной пластиной или двухсторонним резцом (чистовой проход)</td><td colspan="2">-</td><td>0,17</td><td colspan="2">0,20</td><td>0,23</td></tr>
<tr><td>28</td><td rowspan="4">Подрезка торцов</td><td colspan="4">расточной пластиной, зенковкой</td><td colspan="2">-</td><td>0,15</td><td colspan="2">0,17</td><td>0,20</td></tr>
<tr><td>29</td><td colspan="2">резцом в резцедержателе на</td><td colspan="2">по лимбу или разметке</td><td colspan="2">-</td><td>0,38</td><td colspan="2">0,46</td><td>0,55</td></tr>
<tr><td>30</td><td colspan="2" rowspan="2">планшайбе</td><td colspan="2">со взятием пробной</td><td colspan="2">300</td><td>0,8</td><td colspan="2">1,0</td><td>1,15</td></tr>
<tr><td>31</td><td colspan="2">стружки</td><td colspan="2">свыше 300</td><td>0,9</td><td colspan="2">1,1</td><td>1,25</td></tr>
<tr><td>32</td><td rowspan="2">Подрезка пазов</td><td colspan="4">без измерения</td><td colspan="2">-</td><td>0,35</td><td colspan="2">0,40</td><td>0,47</td></tr>
<tr><td>33</td><td colspan="4">с измерением длины расположения размера</td><td colspan="2">-</td><td>0,55</td><td colspan="2">0,7</td><td>0,8</td></tr>
<tr><td>34</td><td rowspan="5">Сверление отверстий</td><td rowspan="2">Обрабатываемый</td><td rowspan="3">Сталь</td><td rowspan="5">Длина отверстия в диаметрах сверла</td><td>5d</td><td colspan="2">-</td><td>0,33</td><td colspan="2">0,41</td><td>0,48</td></tr>
<tr><td>35</td><td>8d</td><td colspan="2">-</td><td>0,47</td><td colspan="2">0,6</td><td>0,7</td></tr>
<tr><td>36</td><td rowspan="3">материал</td><td>свыше 8d</td><td colspan="2">-</td><td>0,6</td><td colspan="2">0,75</td><td>0,9</td></tr>
<tr><td>37</td><td rowspan="2">Чугун</td><td>5d</td><td colspan="2">-</td><td>0,2</td><td colspan="2">0,23</td><td>0,26</td></tr>
<tr><td>38</td><td>свыше 5d</td><td colspan="2">-</td><td>0,33</td><td colspan="2">0,4</td><td>0,47</td></tr>
<tr><td>39</td><td colspan="5">Рассверливание, зенкерование, развертывание</td><td colspan="2">-</td><td>0,17</td><td colspan="2">0,2</td><td>0,23</td></tr>
<tr><td>40</td><td>Фрезерование плоскостей и</td><td colspan="4">по разметке</td><td colspan="2">-</td><td>0,5</td><td colspan="2">0,6</td><td>0,7</td></tr>
<tr><td>41</td><td rowspan="2">пазов</td><td colspan="4" rowspan="2">со взятием стружки</td><td colspan="2">300</td><td>0,8</td><td colspan="2">1,05</td><td>1,2</td></tr>
<tr><td>42</td><td colspan="2">свыше 300</td><td>0,9</td><td colspan="2">1,15</td><td>1,3</td></tr>
<tr><td colspan="8">Индекс</td><td>а</td><td colspan="2">б</td><td>в</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="20%"><col width="9%"><col width="16%"><col width="11%"><col width="6%"><col width="11%"><col width="3%"><col width="8%"><col width="10%"></colgroup>
<tr><td colspan="10">Вспомогательное время, связанное с переходом Горизонтально-расточные станки Среднесерийное производство</td></tr>
<tr><td colspan="8">Карта 96</td><td colspan="2">Лист 4</td></tr>
<tr><td colspan="10">Время на приемы, связанные с переходом, не вошедшие в комплекс</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="5" rowspan="3">Наименование приемов</td><td colspan="4">Диаметр шпинделя, мм, до</td></tr>
<tr><td>65</td><td colspan="2">110</td><td>160</td></tr>
<tr><td colspan="4">Время, мин.</td></tr>
<tr><td>43</td><td colspan="5">Изменить частоту вращения шпинделя</td><td>0,09</td><td colspan="2">0,1</td><td>0,12</td></tr>
<tr><td>44</td><td colspan="5">Изменить величину подачи</td><td>0,07</td><td colspan="2">0,08</td><td>0,09</td></tr>
<tr><td>45</td><td colspan="5">Изменить направление вращения шпинделя</td><td>0,04</td><td colspan="2">0,04</td><td>0,05</td></tr>
<tr><td>46</td><td colspan="5">Изменить направление подачи</td><td>0,04</td><td colspan="2">0,04</td><td>0,05</td></tr>
<tr><td>47</td><td rowspan="6">Установить и снять борштангу</td><td colspan="2" rowspan="2">в конус шпинделя</td><td colspan="2">без крепления</td><td>0,45</td><td colspan="2">0,65</td><td>0,85</td></tr>
<tr><td>48</td><td colspan="2">с креплением</td><td>1,1</td><td colspan="2">1,3</td><td>1,8</td></tr>
<tr><td>49</td><td colspan="2">в конус шпинделя и подшипник задней</td><td colspan="2">вручную</td><td>4,9</td><td colspan="2">5,8</td><td>6,8</td></tr>
<tr><td>50</td><td colspan="2">стойки</td><td colspan="2">краном</td><td>-</td><td colspan="2">-</td><td>11</td></tr>
<tr><td>51</td><td colspan="2" rowspan="2">в конус шпинделя и втулку кондуктора</td><td colspan="2">вручную</td><td>2,4</td><td colspan="2">3,4</td><td>4,3</td></tr>
<tr><td>52</td><td colspan="2">краном</td><td>5,0</td><td colspan="2">7,0</td><td>9,0</td></tr>
<tr><td>53</td><td rowspan="12">Установить и снять инструмент</td><td colspan="4">резец с установкой на размер по шаблону или линейке</td><td>0,6</td><td colspan="2">0,7</td><td>0,8</td></tr>
<tr><td>54</td><td rowspan="7">В борштанге</td><td>Расточная пластина</td><td>Диаметр отверстия, мм,</td><td>100</td><td>0,5</td><td colspan="2">0,6</td><td>0,7</td></tr>
<tr><td>55</td><td>Резец мерный</td><td rowspan="4">до</td><td>200</td><td>0,6</td><td colspan="2">0,7</td><td>0,8</td></tr>
<tr><td>56</td><td>Двусторонний</td><td>350</td><td>1,0</td><td colspan="2">1,1</td><td>1,2</td></tr>
<tr><td>57</td><td>Зенкер, развертка</td><td>100</td><td>0,3</td><td colspan="2">0,4</td><td>0,5</td></tr>
<tr><td>58</td><td>Расточная резцовая головка</td><td>200</td><td>0,9</td><td colspan="2">1,1</td><td>1,3</td></tr>
<tr><td>59</td><td>Расточная резцовая</td><td colspan="2">Вручную</td><td>0,7</td><td colspan="2">0,8</td><td>1,0</td></tr>
<tr><td>60</td><td>головка разъемная</td><td colspan="2">Краном</td><td>-</td><td colspan="2">2,8</td><td>3,0</td></tr>
<tr><td>61</td><td colspan="2" rowspan="2">В конус шпинделя</td><td colspan="2">без крепления</td><td>0,3</td><td colspan="2">0,4</td><td>0,5</td></tr>
<tr><td>62</td><td colspan="2">с креплением</td><td>0,4</td><td colspan="2">0,6</td><td>0,7</td></tr>
<tr><td>63</td><td colspan="2" rowspan="2">Резцедержатель на планшайбе - резец</td><td colspan="2">проходной</td><td>1,0</td><td colspan="2">1,1</td><td>1,2</td></tr>
<tr><td>64</td><td colspan="2">подрезной</td><td>1,2</td><td colspan="2">1,3</td><td>1,4</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td colspan="2">б</td><td>в</td></tr>
</table>



<table>
<colgroup><col width="5%"><col width="27%"><col width="23%"><col width="6%"><col width="8%"><col width="11%"><col width="3%"><col width="8%"><col width="10%"></colgroup>
<tr><td colspan="4" rowspan="2">Вспомогательное время, связанное с переходом Среднесерийное производство</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="3">Карта 96</td><td colspan="2">Лист 5</td></tr>
<tr><td colspan="9">Время на приемы, связанные с переходом, не вошедшие в комплекс</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Наименование приемов</td><td colspan="2" rowspan="3">Измеряемый размер, мм, до</td><td colspan="4">Диаметр шпинделя, мм, до</td></tr>
<tr><td>65</td><td colspan="2">110</td><td>160</td></tr>
<tr><td colspan="4">Время, мин.</td></tr>
<tr><td>65</td><td rowspan="2">Установить и снять кондукторную втулку</td><td rowspan="2">Диаметр отверстия втулки, мм</td><td colspan="2">&lt;= 80</td><td>0,12</td><td colspan="2">0,17</td><td>0,26</td></tr>
<tr><td>66</td><td colspan="2">&lt; 80</td><td>0,19</td><td colspan="2">0,26</td><td>0,35</td></tr>
<tr><td>67</td><td>Переместить (выдвинуть) шпиндель</td><td>Длина перемещения, мм,</td><td colspan="2">300</td><td>0,03</td><td colspan="2">0,03</td><td>0,03</td></tr>
<tr><td>68</td><td rowspan="2">на длину свыше 200 мм</td><td rowspan="6">до</td><td colspan="2">500</td><td>0,08</td><td colspan="2">0,08</td><td>0,08</td></tr>
<tr><td>69</td><td colspan="2">800</td><td>-</td><td colspan="2">1,15</td><td>1,15</td></tr>
<tr><td>70</td><td>Переместить стол станка на длину</td><td colspan="2">300</td><td>0,04</td><td colspan="2">0,04</td><td>0,07</td></tr>
<tr><td>71</td><td rowspan="3">свыше 200 мм</td><td colspan="2">500</td><td>0,10</td><td colspan="2">0,10</td><td>0,16</td></tr>
<tr><td>72</td><td colspan="2">750</td><td>0,19</td><td colspan="2">0,19</td><td>0,30</td></tr>
<tr><td>73</td><td colspan="2">1000</td><td>-</td><td colspan="2">0,29</td><td>0,47</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td colspan="2">б</td><td>в</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="32%"><col width="16%"><col width="15%"><col width="9%"><col width="5%"><col width="4%"><col width="9%"></colgroup>
<tr><td colspan="4" rowspan="2">Вспомогательное время на контрольное измерение Среднесерийное производство</td><td colspan="4">Измерения</td></tr>
<tr><td colspan="2">Карта 97</td><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Измерительный инструмент</td><td rowspan="3">Точность измерения</td><td rowspan="3">Измеряемый размер, мм</td><td colspan="4">Длина измеряемой поверхности, мм</td></tr>
<tr><td>1D</td><td colspan="2">2D</td><td>4D</td></tr>
<tr><td colspan="4">Время, мин.</td></tr>
<tr><td>1</td><td rowspan="8">Калибр-пробка гладкая двухсторонняя</td><td rowspan="4">1Т13 - 1Т11 (5 - 4 кл.)</td><td>10</td><td>0,045</td><td colspan="2">0,05</td><td>-</td></tr>
<tr><td>2</td><td>25</td><td>0,07</td><td colspan="2">0,08</td><td>0,09</td></tr>
<tr><td>3</td><td>50</td><td>0,09</td><td colspan="2">0,10</td><td>0,15</td></tr>
<tr><td>4</td><td>100</td><td>0,12</td><td colspan="2">0,18</td><td>-</td></tr>
<tr><td>5</td><td rowspan="4">1Т9 - 1Т7 (3 - 2 кл.)</td><td>10</td><td>0,07</td><td colspan="2">0,08</td><td>0,09</td></tr>
<tr><td>6</td><td>25</td><td>0,10</td><td colspan="2">0,11</td><td>0,13</td></tr>
<tr><td>7</td><td>50</td><td>0,13</td><td colspan="2">0,15</td><td>0,22</td></tr>
<tr><td>8</td><td>100</td><td>0,18</td><td colspan="2">0,27</td><td>-</td></tr>
<tr><td>9</td><td rowspan="8">Калибр-пробка исподняя (плоская)</td><td rowspan="4">1Т13 - 1Т11 (5 - 4 кл.)</td><td>50</td><td>0,10</td><td colspan="2">0,11</td><td>0,17</td></tr>
<tr><td>10</td><td>100</td><td>0,15</td><td colspan="2">0,23</td><td>-</td></tr>
<tr><td>11</td><td>200</td><td>0,30</td><td colspan="2">-</td><td>-</td></tr>
<tr><td>12</td><td>300</td><td>0,45</td><td colspan="2">-</td><td>-</td></tr>
<tr><td>13</td><td rowspan="4">1Т9 - 1Т7 (3 - 2 кл.)</td><td>50</td><td>0,16</td><td colspan="2">0,19</td><td>0,28</td></tr>
<tr><td>14</td><td>100</td><td>0,25</td><td colspan="2">0,38</td><td>0,50</td></tr>
<tr><td>15</td><td>200</td><td>0,50</td><td colspan="2">-</td><td>-</td></tr>
<tr><td>16</td><td>300</td><td>0,70</td><td colspan="2">-</td><td>-</td></tr>
<tr><td>17</td><td rowspan="4">Пробка-лекало для проверки соосности</td><td rowspan="2">1Т13 - 1Т11 (5 - 4 кл.)</td><td>50</td><td>0,11</td><td colspan="2">0,14</td><td>-</td></tr>
<tr><td>18</td><td>100</td><td>0,17</td><td colspan="2">-</td><td>-</td></tr>
<tr><td>19</td><td rowspan="2">1Т9 - 1Т7 (3 - 2 кл.)</td><td>50</td><td>0,16</td><td colspan="2">0,21</td><td>-</td></tr>
<tr><td>20</td><td>100</td><td>0,25</td><td colspan="2">-</td><td>-</td></tr>
<tr><td>21</td><td>Калибр-пробка односторонняя для проверки</td><td rowspan="3">-</td><td>25</td><td>0,20</td><td colspan="2">-</td><td>-</td></tr>
<tr><td>22</td><td rowspan="2">измеряемого положения оси отверстия и торца</td><td>50</td><td>0,24</td><td colspan="2">-</td><td>-</td></tr>
<tr><td>23</td><td>100</td><td>0,30</td><td colspan="2">-</td><td>-</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="19%"><col width="16%"><col width="15%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="11">Вспомогательное время на контрольное измерение Измерения Среднесерийное производство</td></tr>
<tr><td colspan="9">Карта 97</td><td colspan="2">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Измерительный инструмент</td><td rowspan="3">Точность измерения, мм</td><td rowspan="3">Измеряемый размер, мм</td><td colspan="7">Длина измеряемой поверхности, мм, до</td></tr>
<tr><td>10</td><td>25</td><td>50</td><td>100</td><td>200</td><td>500</td><td>1000</td></tr>
<tr><td colspan="7">Время, мин.</td></tr>
<tr><td>24</td><td>Нутромер или штихмас</td><td rowspan="6">0,01</td><td>50</td><td>-</td><td>-</td><td>0,16</td><td>0,19</td><td>0,24</td><td>0,34</td><td>0,44</td></tr>
<tr><td>25</td><td rowspan="5">индикаторный</td><td>100</td><td>-</td><td>-</td><td>0,18</td><td>0,21</td><td>0,26</td><td>0,38</td><td>0,5</td></tr>
<tr><td>26</td><td>200</td><td>-</td><td>-</td><td>0,20</td><td>0,24</td><td>0,29</td><td>0,42</td><td>0,55</td></tr>
<tr><td>27</td><td>300</td><td>-</td><td>-</td><td>0,21</td><td>0,25</td><td>0,31</td><td>0,45</td><td>0,60</td></tr>
<tr><td>28</td><td>500</td><td>-</td><td>-</td><td>0,35</td><td>0,4</td><td>0,45</td><td>0,55</td><td>0,65</td></tr>
<tr><td>29</td><td>1000</td><td>-</td><td>-</td><td>0,5</td><td>0,55</td><td>0,65</td><td>0,8</td><td>0,9</td></tr>
<tr><td>30</td><td rowspan="6">Штихмас микрометрический</td><td rowspan="6">0,01</td><td>100</td><td>-</td><td>-</td><td>0,22</td><td>0,26</td><td>0,30</td><td>-</td><td>-</td></tr>
<tr><td>31</td><td>200</td><td>-</td><td>-</td><td>0,26</td><td>0,3</td><td>0,36</td><td>0,44</td><td>-</td></tr>
<tr><td>32</td><td>300</td><td>-</td><td>-</td><td>0,28</td><td>0,33</td><td>0,4</td><td>0,48</td><td>-</td></tr>
<tr><td>33</td><td>500</td><td>-</td><td>-</td><td>0,37</td><td>0,46</td><td>0,45</td><td>0,7</td><td>1,1</td></tr>
<tr><td>34</td><td>750</td><td>-</td><td>-</td><td>0,45</td><td>0,5</td><td>0,55</td><td>0,9</td><td>1,35</td></tr>
<tr><td>35</td><td>1000</td><td>-</td><td>-</td><td>0,5</td><td>0,55</td><td>0,65</td><td>1,05</td><td>1,6</td></tr>
<tr><td>36</td><td rowspan="6">Штихмас нераздвижной</td><td rowspan="6">1Т13 - 1Т11 (5 - 4 кл.)</td><td>100</td><td>-</td><td>-</td><td>0,09</td><td>0,1</td><td>0,12</td><td>-</td><td>-</td></tr>
<tr><td>37</td><td>200</td><td>-</td><td>-</td><td>0,1</td><td>0,12</td><td>0,14</td><td>0,17</td><td>-</td></tr>
<tr><td>38</td><td>300</td><td>-</td><td>-</td><td>0,11</td><td>0,13</td><td>0,15</td><td>0,19</td><td>-</td></tr>
<tr><td>39</td><td>500</td><td>-</td><td>-</td><td>0,15</td><td>0,17</td><td>0,19</td><td>0,29</td><td>0,45</td></tr>
<tr><td>40</td><td>750</td><td>-</td><td>-</td><td>0,18</td><td>0,20</td><td>0,23</td><td>0,36</td><td>0,55</td></tr>
<tr><td>41</td><td>1000</td><td>-</td><td>-</td><td>0,21</td><td>0,23</td><td>0,26</td><td>0,43</td><td>0,65</td></tr>
<tr><td>42</td><td rowspan="10">Штангенциркуль</td><td rowspan="10">0,1</td><td>10</td><td>-</td><td>-</td><td>0,07</td><td>0,07</td><td>0,08</td><td>0,10</td><td>-</td></tr>
<tr><td>43</td><td>25</td><td>-</td><td>-</td><td>0,08</td><td>0,08</td><td>0,10</td><td>0,12</td><td>0,17</td></tr>
<tr><td>44</td><td>50</td><td>-</td><td>-</td><td>0,10</td><td>0,12</td><td>0,14</td><td>0,18</td><td>0,22</td></tr>
<tr><td>45</td><td>100</td><td>-</td><td>-</td><td>0,11</td><td>0,14</td><td>0,16</td><td>0,24</td><td>0,29</td></tr>
<tr><td>46</td><td>200</td><td>-</td><td>-</td><td>0,13</td><td>0,16</td><td>0,19</td><td>0,31</td><td>0,38</td></tr>
<tr><td>47</td><td>300</td><td>-</td><td>-</td><td>0,18</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>48</td><td>400</td><td>-</td><td>-</td><td>0,21</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>49</td><td>600</td><td>-</td><td>-</td><td>0,28</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>50</td><td>800</td><td>-</td><td>-</td><td>0,33</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>51</td><td>1000</td><td>-</td><td>-</td><td>0,38</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="4">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="18%"><col width="6%"><col width="8%"><col width="14%"><col width="8%"><col width="8%"><col width="8%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"></colgroup>
<tr><td colspan="12">Вспомогательное время на контрольное измерение Измерения Среднесерийное производство</td></tr>
<tr><td colspan="10">Карта 97</td><td colspan="2">Лист 3</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Измерительный инструмент</td><td colspan="2" rowspan="3">Точность измерения, мм</td><td rowspan="3">Измеряемый размер, мм</td><td colspan="7">Длина измеряемой поверхности, мм, до</td></tr>
<tr><td>10</td><td>25</td><td>50</td><td>100</td><td>200</td><td>500</td><td>1000</td></tr>
<tr><td colspan="7">Время, мин.</td></tr>
<tr><td rowspan="3">52</td><td rowspan="4">Штангенглубиномер</td><td colspan="2"></td><td rowspan="3">-</td><td rowspan="3">0,08</td><td rowspan="3">0,10</td><td rowspan="3">0,11</td><td rowspan="3">0,12</td><td rowspan="3">0,13</td><td rowspan="3">0,15</td><td rowspan="3">-</td></tr>
<tr><td>0,1</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td>53</td><td colspan="2">0,05</td><td>-</td><td>0,12</td><td>0,14</td><td>0,16</td><td>0,17</td><td>0,19</td><td>0,22</td><td>-</td></tr>
<tr><td>54</td><td>Глубиномер микрометрический</td><td colspan="2" rowspan="2">0,01</td><td>-</td><td>-</td><td>-</td><td>0,22</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>55</td><td>Глубиномер индикаторный</td><td>-</td><td>0,04</td><td>0,06</td><td>0,07</td><td>0,09</td><td>0,10</td><td>-</td><td>-</td></tr>
<tr><td>56</td><td>Индикатор для измерения</td><td colspan="2" rowspan="8">0,01</td><td>10</td><td>0,075</td><td>0,085</td><td>0,095</td><td>0,11</td><td>0,12</td><td>-</td><td>-</td></tr>
<tr><td>57</td><td rowspan="7">отклонений от геометрической формы</td><td>25</td><td>0,08</td><td>0,095</td><td>0,105</td><td>0,12</td><td>0,13</td><td>-</td><td>-</td></tr>
<tr><td>58</td><td>50</td><td>0,09</td><td>0,10</td><td>0,11</td><td>0,13</td><td>0,14</td><td>0,19</td><td>-</td></tr>
<tr><td>59</td><td>100</td><td>0,095</td><td>0,11</td><td>0,12</td><td>0,14</td><td>0,15</td><td>0,20</td><td>-</td></tr>
<tr><td>60</td><td>200</td><td>-</td><td>-</td><td>0,13</td><td>0,15</td><td>0,16</td><td>0,22</td><td>-</td></tr>
<tr><td>61</td><td>300</td><td>-</td><td>-</td><td>0,17</td><td>0,19</td><td>0,21</td><td>0,27</td><td>0,35</td></tr>
<tr><td>62</td><td>500</td><td>-</td><td>-</td><td>0,22</td><td>0,24</td><td>0,27</td><td>0,34</td><td>0,42</td></tr>
<tr><td>63</td><td>1000</td><td>-</td><td>-</td><td>0,31</td><td>0,34</td><td>0,38</td><td>0,46</td><td>0,57</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td>д</td><td>е</td><td>ж</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="6%"><col width="3%"></colgroup>
<tr><td colspan="25">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="25">Сталь, чугун, медные сплавы и алюминиевые Борштанги консольные Среднесерийное производство</td></tr>
<tr><td colspan="22">Карта 98</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="5">N позиции</td><td>Диаметр обрабатываемого</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l ,</td><td colspan="10">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td>отверстия D,</td><td>1 l , мм</td><td colspan="21">Режущий инструмент</td></tr>
<tr><td rowspan="3">мм, до</td><td rowspan="3">2</td><td colspan="5">Р6М5</td><td colspan="5">Т5К10</td><td colspan="5">ВК8</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>1</td><td>30</td><td>2</td><td>2</td><td>0,2</td><td>380</td><td>36</td><td>1,32</td><td>1,2</td><td>0,25</td><td>750</td><td>70</td><td>0,53</td><td>1,0</td><td>0,4</td><td>750</td><td>70</td><td>0,44</td><td>1,2</td><td>0,35</td><td>600</td><td colspan="2">56,5</td><td>0,47</td><td>&lt; 1</td></tr>
<tr><td>2</td><td rowspan="2">48</td><td>3</td><td>3</td><td>0,4</td><td rowspan="2">150</td><td rowspan="2">22,5</td><td>1,66</td><td>1,7</td><td>0,35</td><td rowspan="2">480</td><td rowspan="2">72</td><td>0,59</td><td>2,0</td><td>0,45</td><td rowspan="2">480</td><td rowspan="2">72</td><td>0,46</td><td>1,4</td><td>0,5</td><td rowspan="2">380</td><td colspan="2" rowspan="2">57</td><td>0,52</td><td>&lt; 1</td></tr>
<tr><td>3</td><td>5</td><td>5</td><td>0,35</td><td>1,9</td><td>1,7</td><td>0,25</td><td>0,83</td><td>2,9</td><td>0,4</td><td>0,52</td><td>2,9</td><td>0,35</td><td>0,75</td><td>1,1</td></tr>
<tr><td>4</td><td rowspan="2">50</td><td>3</td><td>3</td><td>0,45</td><td rowspan="2">120</td><td rowspan="2">22,5</td><td>1,85</td><td>1,2</td><td>0,45</td><td rowspan="2">300</td><td rowspan="2">57</td><td>0,74</td><td>2,0</td><td>0,7</td><td rowspan="2">300</td><td rowspan="2">57</td><td>0,47</td><td>1,7</td><td>0,7</td><td rowspan="2">240</td><td colspan="2" rowspan="2">45</td><td>0,59</td><td>&lt; 1</td></tr>
<tr><td>5</td><td>5</td><td>5</td><td>0,35</td><td>2,40</td><td>1,7</td><td>0,35</td><td>0,95</td><td>2,9</td><td>0,5</td><td>0,66</td><td>2,9</td><td>0,56</td><td>0,74</td><td>1,3</td></tr>
<tr><td>6</td><td rowspan="3">75</td><td>3</td><td>3</td><td>0,5</td><td rowspan="3">96</td><td rowspan="3">22,5</td><td>2,06</td><td>1,4</td><td>0,5</td><td rowspan="3">240</td><td rowspan="3">57</td><td>0,83</td><td>2,0</td><td>0,7</td><td rowspan="3">240</td><td rowspan="3">57</td><td>0,59</td><td>1,7</td><td>0,7</td><td rowspan="3">190</td><td colspan="2" rowspan="3">45</td><td>0,75</td><td>&lt; 1</td></tr>
<tr><td>7</td><td>5</td><td>5</td><td>0,35</td><td>2,97</td><td>1,4</td><td>0,35</td><td>1,19</td><td>2,9</td><td>0,56</td><td>0,74</td><td>2,9</td><td>0,56</td><td>0,94</td><td>1,1</td></tr>
<tr><td>8</td><td>8</td><td>8</td><td>0,25</td><td>4,16</td><td>2,0</td><td>0,25</td><td>1,66</td><td>3,4</td><td>0,35</td><td>1,19</td><td>2,9</td><td>0,35</td><td>1,5</td><td>1,6</td></tr>
<tr><td>9</td><td rowspan="3">96</td><td>3</td><td>3</td><td>0,5</td><td rowspan="3">75</td><td rowspan="3">22,5</td><td>2,66</td><td>1,4</td><td>0,56</td><td rowspan="3">190</td><td rowspan="3">57</td><td>0,94</td><td>2,4</td><td>0,7</td><td rowspan="3">190</td><td rowspan="3">57</td><td>0,75</td><td>1,7</td><td>0,7</td><td rowspan="3">150</td><td colspan="2" rowspan="3">45</td><td>0,95</td><td>&lt; 1</td></tr>
<tr><td>10</td><td>5</td><td>5</td><td>0,35</td><td>3,80</td><td>1,4</td><td>0,35</td><td>1,5</td><td>2,9</td><td>0,56</td><td>0,94</td><td>2,4</td><td>0,56</td><td>1,19</td><td>1,1</td></tr>
<tr><td>11</td><td>8</td><td>7</td><td>0,25</td><td>5,33</td><td>2,0</td><td>0,30</td><td>1,75</td><td>4,1</td><td>0,35</td><td>1,5</td><td>2,9</td><td>0,35</td><td>1,9</td><td>1,6</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="4"></td><td>в</td><td colspan="5"></td><td>г</td><td></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="6%"><col width="3%"></colgroup>
<tr><td colspan="25">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="25">Сталь, чугун, медные сплавы и алюминиевые Борштанги консольные Среднесерийное производство</td></tr>
<tr><td colspan="22">Карта 98</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="5">N позиции</td><td>Диаметр обрабатываемого</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l ,</td><td colspan="10">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td>отверстия D,</td><td>1 l , мм</td><td colspan="21">Режущий инструмент</td></tr>
<tr><td rowspan="3">мм, до</td><td rowspan="3">2</td><td colspan="5">Р6М5</td><td colspan="5">Т5К10</td><td colspan="5">ВК8</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>12</td><td rowspan="4">120</td><td>3</td><td>3</td><td>0,5</td><td rowspan="4">60</td><td rowspan="4">22,5</td><td>3,33</td><td>1,4</td><td>0,56</td><td rowspan="4">150</td><td rowspan="4">56</td><td>1,19</td><td>2,4</td><td>0,7</td><td rowspan="4">150</td><td rowspan="4">56</td><td>0,95</td><td>1,7</td><td>0,7</td><td rowspan="4">120</td><td colspan="2" rowspan="4">45</td><td>1,19</td><td>1,0</td></tr>
<tr><td>13</td><td>5</td><td>5</td><td>0,4</td><td>4,16</td><td>1,7</td><td>0,45</td><td>1,48</td><td>3,4</td><td>0,56</td><td>1,19</td><td>2,4</td><td>0,56</td><td>1,49</td><td>1,1</td></tr>
<tr><td>14</td><td>8</td><td>7</td><td>0,3</td><td>5,55</td><td>2,0</td><td>0,35</td><td>1,9</td><td>4,1</td><td>0,45</td><td>1,48</td><td>2,9</td><td>0,45</td><td>1,85</td><td>1,6</td></tr>
<tr><td>15</td><td>12</td><td>9</td><td>0,25</td><td>6,66</td><td>2,9</td><td>0,22</td><td>3,03</td><td>4,9</td><td>0,35</td><td>1,9</td><td>4,1</td><td>0,35</td><td>2,38</td><td>2,2</td></tr>
<tr><td>16</td><td rowspan="4">150</td><td>3</td><td>3</td><td>0,5</td><td rowspan="4">48</td><td rowspan="4">22,5</td><td>4,16</td><td>1,4</td><td>0,56</td><td rowspan="4">120</td><td rowspan="4">56</td><td>1,48</td><td>2,4</td><td>0,7</td><td rowspan="4">120</td><td rowspan="4">56</td><td>1,19</td><td>1,7</td><td>0,7</td><td rowspan="4">96</td><td colspan="2" rowspan="4">45</td><td>1,49</td><td>1,0</td></tr>
<tr><td>17</td><td>5</td><td>5</td><td>0,4</td><td>5,2</td><td>1,7</td><td>0,45</td><td>1,85</td><td>3,4</td><td>0,56</td><td>1,48</td><td>2,4</td><td>0,56</td><td>1,86</td><td>1,3</td></tr>
<tr><td>18</td><td>8</td><td>7</td><td>0,3</td><td>6,94</td><td>2,0</td><td>0,35</td><td>2,38</td><td>4,1</td><td>0,45</td><td>1,85</td><td>2,9</td><td>0,45</td><td>2,31</td><td>1,6</td></tr>
<tr><td>19</td><td>12</td><td>9</td><td>0,25</td><td>8,33</td><td>2,9</td><td>0,22</td><td>3,78</td><td>4,9</td><td>0,35</td><td>2,38</td><td>4,1</td><td>0,35</td><td>2,97</td><td>2,2</td></tr>
<tr><td>20</td><td rowspan="4">190</td><td>3</td><td>3</td><td>0,5</td><td rowspan="4">38</td><td rowspan="4">22,5</td><td>5,26</td><td>1,4</td><td>0,56</td><td rowspan="4">96</td><td rowspan="4">57</td><td>1,86</td><td>2,4</td><td>0,7</td><td rowspan="4">96</td><td rowspan="4">57</td><td>1,49</td><td>1,7</td><td>0,7</td><td rowspan="4">75</td><td colspan="2" rowspan="4">45</td><td>1,9</td><td>1,0</td></tr>
<tr><td>21</td><td>5</td><td>5</td><td>0,4</td><td>6,57</td><td>1,7</td><td>0,45</td><td>2,31</td><td>3,4</td><td>0,56</td><td>1,86</td><td>2,4</td><td>0,56</td><td>2,38</td><td>1,3</td></tr>
<tr><td>22</td><td>8</td><td>7</td><td>0,3</td><td>8,77</td><td>2,0</td><td>0,35</td><td>2,97</td><td>4,1</td><td>0,45</td><td>2,31</td><td>2,9</td><td>0,45</td><td>2,96</td><td>1,6</td></tr>
<tr><td>23</td><td>12</td><td>9</td><td>0,25</td><td>10,5</td><td>2,9</td><td>0,22</td><td>4,73</td><td>4,9</td><td>0,35</td><td>2,97</td><td>4,1</td><td>0,35</td><td>3,8</td><td>2,2</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="4"></td><td>в</td><td colspan="5"></td><td>г</td><td></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="6%"><col width="3%"></colgroup>
<tr><td colspan="25">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="25">Сталь, чугун, медные сплавы и алюминиевые Борштанги консольные Среднесерийное производство</td></tr>
<tr><td colspan="22">Карта 98</td><td colspan="3">Лист 3</td></tr>
<tr><td rowspan="5">N позиции</td><td>Диаметр обрабатываемого</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l ,</td><td colspan="10">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td>отверстия D,</td><td>1 l , мм</td><td colspan="21">Режущий инструмент</td></tr>
<tr><td rowspan="3">мм, до</td><td rowspan="3">2</td><td colspan="5">Р6М5</td><td colspan="5">Т5К10</td><td colspan="5">ВК8</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>24</td><td rowspan="4">240</td><td>3</td><td>3</td><td>0,5</td><td rowspan="4">30</td><td rowspan="4">22,5</td><td>6,66</td><td>1,4</td><td>0,56</td><td rowspan="4">75</td><td rowspan="4">56</td><td>2,38</td><td>2,4</td><td>0,7</td><td rowspan="4">75</td><td rowspan="4">56</td><td>1,9</td><td>1,7</td><td>0,7</td><td rowspan="4">60</td><td colspan="2" rowspan="4">45</td><td>2,38</td><td>&lt; 1</td></tr>
<tr><td>25</td><td>5</td><td>5</td><td>0,4</td><td>8,33</td><td>1,7</td><td>0,45</td><td>2,96</td><td>3,4</td><td>0,56</td><td>2,38</td><td>2,4</td><td>0,56</td><td>2,97</td><td>1,3</td></tr>
<tr><td>26</td><td>8</td><td>7</td><td>0,3</td><td>11,1</td><td>2,0</td><td>0,35</td><td>3,8</td><td>4,1</td><td>0,45</td><td>2,96</td><td>2,9</td><td>0,45</td><td>3,7</td><td>1,6</td></tr>
<tr><td>27</td><td>12</td><td>9</td><td>0,25</td><td>13,3</td><td>2,9</td><td>0,22</td><td>6,06</td><td>4,9</td><td>0,35</td><td>3,8</td><td>4,1</td><td>0,35</td><td>4,76</td><td>2,2</td></tr>
<tr><td>28</td><td rowspan="4">300</td><td>3</td><td>3</td><td>0,5</td><td rowspan="4">24</td><td rowspan="4">22,5</td><td>8,33</td><td>1,4</td><td>0,56</td><td rowspan="4">60</td><td rowspan="4">56</td><td>2,97</td><td>2,4</td><td>0,7</td><td rowspan="4">60</td><td rowspan="4">56</td><td>2,38</td><td>1,7</td><td>0,7</td><td rowspan="4">48</td><td colspan="2" rowspan="4">45</td><td>2,97</td><td>&lt; 1</td></tr>
<tr><td>29</td><td>5</td><td>5</td><td>0,4</td><td>10,4</td><td>1,7</td><td>0,45</td><td>3,7</td><td>3,4</td><td>0,56</td><td>2,97</td><td>2,4</td><td>0,56</td><td>3,72</td><td>1,3</td></tr>
<tr><td>30</td><td>8</td><td>7</td><td>0,3</td><td>13,9</td><td>2,0</td><td>0,35</td><td>4,76</td><td>4,1</td><td>0,45</td><td>3,7</td><td>2,9</td><td>0,45</td><td>4,63</td><td>1,6</td></tr>
<tr><td>31</td><td>12</td><td>9</td><td>0,25</td><td>16,6</td><td>2,9</td><td>0,22</td><td>7,57</td><td>4,9</td><td>0,35</td><td>4,76</td><td>4,1</td><td>0,35</td><td>5,95</td><td>2,2</td></tr>
<tr><td>32</td><td rowspan="4">380</td><td>3</td><td>3</td><td>0,5</td><td rowspan="4">19</td><td rowspan="4">23</td><td>10,5</td><td>1,4</td><td>0,56</td><td rowspan="4">48</td><td rowspan="4">57</td><td>3,72</td><td>2,4</td><td>0,7</td><td rowspan="4">48</td><td rowspan="4">57</td><td>2,97</td><td>1,7</td><td>0,7</td><td rowspan="4">38</td><td colspan="2" rowspan="4">45</td><td>3,75</td><td>&lt; 1</td></tr>
<tr><td>33</td><td>5</td><td>5</td><td>0,4</td><td>13,1</td><td>1,7</td><td>0,45</td><td>4,63</td><td>3,4</td><td>0,56</td><td>3,72</td><td>2,4</td><td>0,56</td><td>4,7</td><td>1,3</td></tr>
<tr><td>34</td><td>8</td><td>7</td><td>0,3</td><td>17,5</td><td>2,0</td><td>0,35</td><td>5,95</td><td>4,1</td><td>0,45</td><td>4,63</td><td>2,9</td><td>0,45</td><td>5,84</td><td>1,6</td></tr>
<tr><td>35</td><td>12</td><td>12</td><td>0,25</td><td>21,0</td><td>2,9</td><td>0,22</td><td>9,47</td><td>4,9</td><td>0,35</td><td>5,95</td><td>4,1</td><td>0,35</td><td>7,52</td><td>2,2</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="4"></td><td>в</td><td colspan="5"></td><td>г</td><td></td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="9%"><col width="12%"><col width="20%"><col width="6%"><col width="3%"><col width="3%"><col width="2%"><col width="2%"><col width="7%"><col width="6%"><col width="3%"><col width="4%"><col width="3%"><col width="7%"></colgroup>
<tr><td colspan="7">Основное время на 100 мм расчетной длины Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="7" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="8">Борштанги контрольные</td></tr>
<tr><td colspan="8">Карта 98 Лист 4</td></tr>
<tr><td colspan="15">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="9">Группы стали и предела прочности</td><td rowspan="9">Инструмент</td><td rowspan="5">Из быстрорежущей стали Р6М5</td><td>Группа стали</td><td colspan="6">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="5">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="3">0,59 - 0,74</td><td>свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="3"></td><td rowspan="3">1,25</td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td colspan="2">1,0</td><td></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td rowspan="4">С пластинками из твердого сплава Т5К10</td><td>Группа стали и предел прочности, ГПа</td><td colspan="2">до 0,59</td><td colspan="3">0,59 - 0,74</td><td>свыше 0,74</td><td colspan="5" rowspan="4">-</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="3"></td><td rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="3" rowspan="4">Твердости чугуна</td><td>Твердость чугуна НВ, ГПа</td><td colspan="6">до 2,15</td><td colspan="5">свыше 2,15</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="6"></td><td colspan="5" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="5"></td></tr>
<tr><td colspan="6"></td></tr>
<tr><td colspan="3" rowspan="5">Группы медных сплавов и твердости</td><td>Группа сплавов</td><td colspan="6">Гомогенные</td><td colspan="5">Гетерогенные</td></tr>
<tr><td>Твердость НВ, ГПа</td><td colspan="6">0,59 - 0,88</td><td colspan="3">0,98 - 1,37</td><td colspan="2">1,47 - 2,45</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="6" rowspan="3">0,55</td><td colspan="3"></td><td colspan="2" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="3" rowspan="3">Группы алюминиевых сплавов и твердости</td><td>Группа сплавов</td><td colspan="6">Силумин и литейные сплавы</td><td colspan="5">Дюралюминий</td></tr>
<tr><td>Твердость НВ, ГПа</td><td colspan="6">до 0,64</td><td colspan="5">до 0,98</td></tr>
<tr><td>Коэффициент</td><td colspan="6">0,75</td><td colspan="5">0,7</td></tr>
<tr><td colspan="3" rowspan="4">Состояния обрабатываемой поверхности</td><td colspan="3">Состояние обрабатываемой поверхности</td><td colspan="4">без корки и удара</td><td colspan="5">по корке и на удар</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="5" rowspan="3">1,2</td></tr>
<tr><td colspan="2">1,0</td><td colspan="2"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="6%"><col width="3%"></colgroup>
<tr><td colspan="25">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="25">Сталь, чугун, медные сплавы и алюминиевые Борштанги двухопорные Среднесерийное производство</td></tr>
<tr><td colspan="22">Карта 99</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="5">N позиции</td><td>Диаметр обрабатываемого</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l ,</td><td colspan="10">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td>отверстия D,</td><td>1 l , мм</td><td colspan="21">Режущий инструмент</td></tr>
<tr><td rowspan="3">мм, до</td><td rowspan="3">2</td><td colspan="5">Р6М5</td><td colspan="5">Т5К10</td><td colspan="5">ВК8</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>1</td><td rowspan="4">120</td><td>3</td><td>3</td><td>0,70</td><td rowspan="4">48</td><td rowspan="4">18</td><td>2,97</td><td>1,5</td><td>0,7</td><td rowspan="4">150</td><td rowspan="4">56</td><td>0,95</td><td>2,7</td><td>0,9</td><td rowspan="4">120</td><td rowspan="4">45</td><td>0,92</td><td>1,5</td><td>0,9</td><td rowspan="4">96</td><td colspan="2" rowspan="4">36</td><td>1,15</td><td>0,9</td></tr>
<tr><td>2</td><td>5</td><td>5</td><td>0,56</td><td>3,72</td><td>1,7</td><td>0,56</td><td>1,19</td><td>3,8</td><td>0,7</td><td>1,19</td><td>2,0</td><td>0,7</td><td>1,49</td><td>1,3</td></tr>
<tr><td>3</td><td>8</td><td>7</td><td>0,45</td><td>4,63</td><td>1,9</td><td>0,45</td><td>1,48</td><td>5,4</td><td>0,56</td><td>1,49</td><td>3,0</td><td>0,56</td><td>1,86</td><td>1,8</td></tr>
<tr><td>4</td><td>12</td><td>9</td><td>0,35</td><td>5,95</td><td>2,3</td><td>0,35</td><td>1,9</td><td>6,5</td><td>0,45</td><td>1,85</td><td>3,6</td><td>0,45</td><td>2,31</td><td>2,4</td></tr>
<tr><td>5</td><td rowspan="4">150</td><td>3</td><td>3</td><td>0,70</td><td rowspan="4">38</td><td rowspan="4">18</td><td>3,75</td><td>1,5</td><td>0,7</td><td rowspan="4">120</td><td rowspan="4">56</td><td>1,19</td><td>2,7</td><td>0,9</td><td rowspan="4">96</td><td rowspan="4">45</td><td>1,15</td><td>1,5</td><td>0,9</td><td rowspan="4">75</td><td colspan="2" rowspan="4">35</td><td>1,48</td><td>0,9</td></tr>
<tr><td>6</td><td>5</td><td>5</td><td>0,56</td><td>4,7</td><td>1,7</td><td>0,56</td><td>1,49</td><td>3,8</td><td>0,7</td><td>1,49</td><td>2,0</td><td>0,7</td><td>1,9</td><td>1,3</td></tr>
<tr><td>7</td><td>8</td><td>7</td><td>0,45</td><td>5,84</td><td>1,9</td><td>0,45</td><td>1,85</td><td>5,4</td><td>0,56</td><td>1,86</td><td>3,0</td><td>0,56</td><td>2,38</td><td>1,8</td></tr>
<tr><td>8</td><td>12</td><td>9</td><td>0,35</td><td>7,52</td><td>2,3</td><td>0,35</td><td>2,38</td><td>6,5</td><td>0,45</td><td>2,31</td><td>3,6</td><td>0,45</td><td>2,96</td><td>2,4</td></tr>
<tr><td>9</td><td rowspan="4">190</td><td>3</td><td>3</td><td>0,70</td><td rowspan="4">30</td><td rowspan="4">18</td><td>4,76</td><td>1,5</td><td>0,7</td><td rowspan="4">96</td><td rowspan="4">57</td><td>1,49</td><td>2,7</td><td>0,9</td><td rowspan="4">75</td><td rowspan="4">45</td><td>1,48</td><td>1,5</td><td>0,9</td><td rowspan="4">60</td><td colspan="2" rowspan="4">36</td><td>1,85</td><td>0,9</td></tr>
<tr><td>10</td><td>5</td><td>5</td><td>0,56</td><td>5,95</td><td>1,7</td><td>0,56</td><td>1,86</td><td>3,8</td><td>0,7</td><td>1,9</td><td>2,0</td><td>0,7</td><td>2,38</td><td>1,3</td></tr>
<tr><td>11</td><td>8</td><td>7</td><td>0,45</td><td>7,4</td><td>1,9</td><td>0,45</td><td>2,31</td><td>5,4</td><td>0,56</td><td>2,38</td><td>3,0</td><td>0,56</td><td>2,97</td><td>1,8</td></tr>
<tr><td>12</td><td>12</td><td>9</td><td>0,35</td><td>9,52</td><td>2,3</td><td>0,35</td><td>2,97</td><td>6,5</td><td>0,45</td><td>2,96</td><td>3,6</td><td>0,45</td><td>3,7</td><td>2,4</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="4"></td><td>в</td><td colspan="5"></td><td>г</td><td></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="6%"><col width="3%"></colgroup>
<tr><td colspan="25">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет</td></tr>
<tr><td colspan="25">Сталь, чугун, медные сплавы и алюминиевые Борштанги двухопорные Среднесерийное производство</td></tr>
<tr><td colspan="22">Карта 99</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="5">N позиции</td><td>Диаметр обрабатываемого</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l ,</td><td colspan="10">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td>отверстия D,</td><td>1 l , мм</td><td colspan="21">Режущий инструмент</td></tr>
<tr><td rowspan="3">мм, до</td><td rowspan="3">2</td><td colspan="5">Р6М5</td><td colspan="5">Т5К10</td><td colspan="5">ВК8</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>13</td><td rowspan="4">240</td><td>3</td><td>3</td><td>0,7</td><td rowspan="4">24</td><td rowspan="16">18</td><td>5,95</td><td>1,5</td><td>0,7</td><td rowspan="4">75</td><td rowspan="4">56</td><td>1,9</td><td>2,7</td><td>0,9</td><td rowspan="4">60</td><td rowspan="16">45</td><td>1,85</td><td>1,5</td><td>0,9</td><td rowspan="4">48</td><td colspan="2" rowspan="16">36</td><td>2,31</td><td>0,9</td></tr>
<tr><td>14</td><td>5</td><td>5</td><td>0,56</td><td>7,44</td><td>1,7</td><td>0,56</td><td>2,38</td><td>3,8</td><td>0,7</td><td>2,38</td><td>2,0</td><td>0,7</td><td>2,97</td><td>1,3</td></tr>
<tr><td>15</td><td>8</td><td>7</td><td>0,45</td><td>9,26</td><td>1,9</td><td>0,45</td><td>2,96</td><td>5,4</td><td>0,56</td><td>2,97</td><td>3,0</td><td>0,56</td><td>3,72</td><td>1,8</td></tr>
<tr><td>16</td><td>12</td><td>9</td><td>0,35</td><td>11,9</td><td>2,3</td><td>0,35</td><td>3,8</td><td>6,5</td><td>0,45</td><td>3,7</td><td>3,6</td><td>0,45</td><td>4,63</td><td>2,4</td></tr>
<tr><td>17</td><td rowspan="4">300</td><td>3</td><td>3</td><td>0,7</td><td rowspan="4">19</td><td>7,52</td><td>1,5</td><td>0,7</td><td rowspan="4">60</td><td rowspan="12">57</td><td>2,38</td><td>2,7</td><td>0,9</td><td rowspan="4">48</td><td>2,31</td><td>1,5</td><td>0,9</td><td rowspan="4">38</td><td>2,92</td><td>0,9</td></tr>
<tr><td>18</td><td>5</td><td>5</td><td>0,56</td><td>9,40</td><td>1,7</td><td>0,56</td><td>2,97</td><td>3,8</td><td>0,7</td><td>2,97</td><td>2,0</td><td>0,7</td><td>3,76</td><td>1,3</td></tr>
<tr><td>19</td><td>8</td><td>7</td><td>0,45</td><td>11,7</td><td>1,9</td><td>0,45</td><td>3,7</td><td>5,4</td><td>0,56</td><td>3,72</td><td>3,0</td><td>0,56</td><td>4,7</td><td>1,8</td></tr>
<tr><td>20</td><td>12</td><td>9</td><td>0,35</td><td>15</td><td>2,3</td><td>0,35</td><td>4,76</td><td>6,5</td><td>0,45</td><td>4,63</td><td>3,6</td><td>0,45</td><td>5,84</td><td>2,4</td></tr>
<tr><td>21</td><td rowspan="4">380</td><td>3</td><td>3</td><td>0,7</td><td rowspan="4">15</td><td>9,52</td><td>1,5</td><td>0,7</td><td rowspan="4">48</td><td>2,97</td><td>2,7</td><td>0,9</td><td rowspan="4">38</td><td>2,92</td><td>1,5</td><td>0,9</td><td rowspan="4">30</td><td>3,7</td><td>0,9</td></tr>
<tr><td>22</td><td>5</td><td>5</td><td>0,56</td><td>11,9</td><td>1,7</td><td>0,56</td><td>3,72</td><td>3,8</td><td>0,7</td><td>3,76</td><td>2,0</td><td>0,7</td><td>4,76</td><td>1,3</td></tr>
<tr><td>23</td><td>8</td><td>7</td><td>0,45</td><td>14,8</td><td>1,9</td><td>0,45</td><td>4,63</td><td>5,4</td><td>0,56</td><td>4,7</td><td>3,0</td><td>0,56</td><td>5,95</td><td>1,8</td></tr>
<tr><td>24</td><td>12</td><td>9</td><td>0,35</td><td>19</td><td>2,3</td><td>0,35</td><td>5,95</td><td>6,5</td><td>0,45</td><td>5,84</td><td>3,6</td><td>0,45</td><td>7,4</td><td>2,4</td></tr>
<tr><td>25</td><td rowspan="4">480</td><td>3</td><td>3</td><td>0,7</td><td rowspan="4">12</td><td>11,9</td><td>1,5</td><td>0,7</td><td rowspan="4">38</td><td>3,76</td><td>2,7</td><td>0,9</td><td rowspan="4">30</td><td>3,7</td><td>1,5</td><td>0,9</td><td rowspan="4">24</td><td>4,63</td><td>0,9</td></tr>
<tr><td>26</td><td>5</td><td>5</td><td>0,56</td><td>14,9</td><td>1,7</td><td>0,56</td><td>4,7</td><td>3,8</td><td>0,7</td><td>4,76</td><td>2,0</td><td>0,7</td><td>5,95</td><td>1,3</td></tr>
<tr><td>27</td><td>8</td><td>7</td><td>0,45</td><td>18,5</td><td>1,9</td><td>0,45</td><td>5,84</td><td>5,4</td><td>0,56</td><td>5,95</td><td>3,0</td><td>0,56</td><td>7,44</td><td>1,8</td></tr>
<tr><td>28</td><td>12</td><td>9</td><td>0,35</td><td>23,8</td><td>2,3</td><td>0,35</td><td>7,52</td><td>6,5</td><td>0,45</td><td>7,4</td><td>3,6</td><td>0,45</td><td>9,26</td><td>2,4</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="4"></td><td>в</td><td colspan="5"></td><td>г</td><td></td></tr>
</table>



```text
┌─────────────────────────────────────────────────────────┬──────────────────────────────┐
│Основное время на 100 мм расчетной длины                 │Горизонтально-расточные станки│
│Растачивание отверстий, Rz 80, 1Т14 - 1Т12 квалитет      ├──────────────────────────────┤
│Сталь, чугун, медные сплавы и алюминиевые                │    Борштанги двухопорные     │
│Среднесерийное производство                              ├────────────────┬─────────────┤
│                                                         │    Карта 99    │   Лист 3    │
├─────────────────────────────────────────────────────────┴────────────────┴─────────────┤
│               Поправочные коэффициенты на время обработки для измененных               │
│                            условий работы в зависимости от:                            │
├─────────┬───────┬──────────┬─────────────────┬────────────────────┬────────────────────┤
│Группы   │Инстру-│Из быстро-│Группа стали     │   Углеродистые,    │  Марганцовистые,   │
│стали и  │мент   │режущей   │                 │     хромистые,     │хромомарганцовистые,│
│предела  │       │стали Р6М5│                 │     никелевые,     │хромомолибденовые и │
│прочности│       │          │                 │   хромоникелевые   │   близкие к ним    │
│         │       │          ├─────────────────┼───────┬──────┬─────┼───────┬──────┬─────┤
│         │       │          │Предел прочности │до 0,59│0,59 -│свыше│до 0,59│0,59 -│свыше│
│         │       │          │сигма , ГПа      │       │0,74  │0,74 │       │0,74  │0,74 │
│         │       │          │     в           │       │      │     │       │      │     │
│         │       │          ├─────────────────┼───────┼──────┼─────┼───────┼──────┼─────┤
│         │       │          │                 │       │┌───┐ │     │       │      │     │
│         │       │          │Коэффициент      │0,8    ││1,0│ │1,25 │1,1    │1,2   │1,35 │
│         │       │          │                 │       │└───┘ │     │       │      │     │
│         │       ├──────────┼─────────────────┼───────┼──────┼─────┼───────┴──────┴─────┤
│         │       │С пластин-│Предел прочности │до 0,59│0,59 -│свыше│         -          │
│         │       │ками из   │сигма , ГПа      │       │0,74  │0,74 │                    │
│         │       │твердого  │     в           │       │      │     │                    │
│         │       │сплава    ├─────────────────┼───────┼──────┼─────┤                    │
│         │       │Т5К10     │                 │       │┌───┐ │     │                    │
│         │       │          │Коэффициент      │0,8    ││1,0│ │1,25 │                    │
│         │       │          │                 │       │└───┘ │     │                    │
├─────────┴───────┴──────────┼─────────────────┼───────┴──────┴─────┼────────────────────┤
│Твердости чугуна            │Твердость чугуна │до 2,15             │2,15                │
│                            │НВ, ГПа          │                    │                    │
│                            ├─────────────────┼────────────────────┼────────────────────┤
│                            │                 │┌───┐               │                    │
│                            │Коэффициент      ││1,0│               │1,25                │
│                            │                 │└───┘               │                    │
├────────────────────────────┼─────────────────┼────────────────────┼────────────────────┤
│Группы медных сплавов и     │Группа сплавов   │Гомогенные          │    Гетерогенные    │
│твердости                   ├─────────────────┼────────────────────┼───────────┬────────┤
│                            │Твердость НВ, ГПа│0,59 - 0,88         │0,98 - 1,37│1,47 -  │
│                            │                 │                    │           │2,45    │
│                            ├─────────────────┼────────────────────┼───────────┼────────┤
│                            │                 │                    │┌───┐      │        │
│                            │Коэффициент      │0,55                ││1,0│      │1,25    │
│                            │                 │                    │└───┘      │        │
├─────────┬──────────────────┼─────────────────┴────────────────────┼───────────┴────────┤
│Группы   │Группа сплавов    │Силумин и литейные сплавы             │Дюралюминий         │
│алюминие-├──────────────────┼──────────────────────────────────────┼────────────────────┤
│вых      │Твердость НВ, ГПа │до 0,64                               │до 0,98             │
│сплавов и├──────────────────┼──────────────────────────────────────┼────────────────────┤
│твердости│Коэффициент       │0,75                                  │0,7                 │
├─────────┼──────────────────┴─────────────────┬────────────────────┼────────────────────┤
│Состояния│Состояние обрабатываемой поверхности│без корки и удара   │по корке и на удар  │
│обрабаты-├────────────────────────────────────┼────────────────────┼────────────────────┤
│ваемой   │                                    │┌───┐               │                    │
│поверх-  │Коэффициент                         ││1,0│               │1,2                 │
│ности    │                                    │└───┘               │                    │
└─────────┴────────────────────────────────────┴────────────────────┴────────────────────┘
```



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="2%"><col width="1%"><col width="6%"><col width="3%"></colgroup>
<tr><td colspan="18">Основное время на 100 мм расчетной длины Растачивание отверстий, Rz 20, 1Т9 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="18" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Резцы из стали Р6М5 и с пластинками Т15К6, ВК6</td></tr>
<tr><td colspan="4">Карта 100</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="5">N позиции</td><td>Диаметр обрабатываемого</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l ,</td><td colspan="10">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td>отверстия D,</td><td>1 l , мм</td><td colspan="21">Режущий инструмент</td></tr>
<tr><td rowspan="3">мм, до</td><td rowspan="3">2</td><td colspan="5">Р6М5</td><td colspan="5">Т15К6</td><td colspan="5">ВК8</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>1</td><td>30</td><td rowspan="12">1</td><td rowspan="12">2</td><td rowspan="12">0,35</td><td>380</td><td rowspan="12">37</td><td>0,75</td><td rowspan="12">1</td><td>0,25</td><td>1200</td><td rowspan="12">113</td><td>0,33</td><td rowspan="12">1,9</td><td>0,25</td><td>750</td><td rowspan="12">57</td><td>0,53</td><td rowspan="12">1</td><td>0,3</td><td>750</td><td colspan="2" rowspan="12">70</td><td>0,44</td><td rowspan="12">1</td></tr>
<tr><td>2</td><td>48</td><td>240</td><td>1,19</td><td rowspan="11">0,35</td><td>750</td><td>0,38</td><td rowspan="11">0,45</td><td>380</td><td>0,58</td><td rowspan="11">0,45</td><td>480</td><td>0,46</td></tr>
<tr><td>3</td><td>60</td><td>190</td><td>1,5</td><td>600</td><td>0,476</td><td>300</td><td>0,74</td><td>380</td><td>0,58</td></tr>
<tr><td>4</td><td>75</td><td>150</td><td>1,9</td><td>480</td><td>0,59</td><td>240</td><td>0,93</td><td>300</td><td>0,74</td></tr>
<tr><td>5</td><td>96</td><td>120</td><td>2,38</td><td>380</td><td>0,75</td><td>190</td><td>1,17</td><td>240</td><td>0,93</td></tr>
<tr><td>6</td><td>120</td><td>96</td><td>2,97</td><td>300</td><td>0,95</td><td>150</td><td>1,48</td><td>190</td><td>1,17</td></tr>
<tr><td>7</td><td>150</td><td>75</td><td>3,81</td><td>240</td><td>1,20</td><td>120</td><td>1,85</td><td>150</td><td>1,48</td></tr>
<tr><td>8</td><td>190</td><td>60</td><td>4,76</td><td>190</td><td>1,50</td><td>96</td><td>2,31</td><td>120</td><td>1,85</td></tr>
<tr><td>9</td><td>240</td><td>48</td><td>5,95</td><td>150</td><td>1,90</td><td>75</td><td>2,96</td><td>96</td><td>2,31</td></tr>
<tr><td>10</td><td>300</td><td>38</td><td>7,52</td><td>120</td><td>2,38</td><td>60</td><td>3,70</td><td>75</td><td>2,96</td></tr>
<tr><td>11</td><td>380</td><td>30</td><td>9,52</td><td>96</td><td>2,97</td><td>48</td><td>4,63</td><td>60</td><td>3,70</td></tr>
<tr><td>12</td><td>480</td><td>24</td><td>11,9</td><td>75</td><td>3,81</td><td>38</td><td>5,85</td><td>48</td><td>4,63</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="4"></td><td>в</td><td colspan="5"></td><td>г</td><td></td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="9%"><col width="12%"><col width="20%"><col width="5%"><col width="3%"><col width="8%"><col width="7%"><col width="5%"><col width="3%"><col width="2%"><col width="2%"><col width="4%"><col width="9%"></colgroup>
<tr><td colspan="14">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Растачивание отверстий, Rz 20, 1Т9 квалитет</td></tr>
<tr><td colspan="14">Сталь, чугун, медные сплавы и алюминиевые Резцы из стали Р6М5 и с Среднесерийное производство пластинками Т15К6, ВК6</td></tr>
<tr><td colspan="11">Карта 100</td><td colspan="3">Лист 2</td></tr>
<tr><td colspan="14">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="9">Группы стали и предела прочности</td><td rowspan="9">Инструмент</td><td rowspan="5">Из быстрорежущей стали Р6М5</td><td>Группа стали</td><td colspan="4">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="6">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td>0,59 - 0,74</td><td>свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="3">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td></td><td rowspan="3">1,25</td><td colspan="2" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td>1,0</td></tr>
<tr><td></td></tr>
<tr><td rowspan="4">С пластинками из твердого сплава Т15К6</td><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td>0,59 - 0,74</td><td>свыше 0,74</td><td colspan="6" rowspan="4">-</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td></td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td></tr>
<tr><td></td></tr>
<tr><td colspan="3" rowspan="4">Твердости чугуна</td><td>Твердость чугуна НВ, ГПа</td><td colspan="4">до 2,15</td><td colspan="6">свыше 2,15</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="6" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td colspan="3" rowspan="5">Группы медных сплавов и твердости</td><td>Группа сплавов</td><td colspan="4">Гомогенные</td><td colspan="6">Гетерогенные</td></tr>
<tr><td>Твердость НВ, ГПа</td><td colspan="4">0,59 - 0,88</td><td colspan="4">0,98 - 1,37</td><td colspan="2">1,47 - 2,45</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4" rowspan="3">0,55</td><td colspan="4"></td><td colspan="2" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td colspan="3" rowspan="3">Группы алюминиевых сплавов и твердости</td><td>Группа сплавов</td><td colspan="8">Силумин и литейные сплавы</td><td colspan="2">Дюралюминий</td></tr>
<tr><td>Твердость НВ, ГПа</td><td colspan="8">до 0,64</td><td colspan="2">до 0,98</td></tr>
<tr><td>Коэффициент</td><td colspan="8">0,75</td><td colspan="2">0,7</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="2%"><col width="1%"><col width="6%"><col width="3%"></colgroup>
<tr><td colspan="18">Основное время на 100 мм расчетной длины Растачивание отверстий, Rz 2,5, 1Т9 - 1Т8 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="18" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Резцы из стали Р6М5 и с пластинками Т15К6, ВК6</td></tr>
<tr><td colspan="4">Карта 101</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="5">N позиции</td><td>Диаметр обрабатываемого</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l ,</td><td colspan="10">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td>отверстия D,</td><td>1 l , мм</td><td colspan="21">Режущий инструмент</td></tr>
<tr><td rowspan="3">мм, до</td><td rowspan="3">2</td><td colspan="5">Р6М5</td><td colspan="5">Т15К6</td><td colspan="5">ВК6</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>1</td><td>30</td><td rowspan="12">1,0</td><td rowspan="12">2,0</td><td rowspan="12">0,18</td><td>480</td><td>45</td><td>1,15</td><td rowspan="12">до 1</td><td rowspan="12">0,18</td><td>1200</td><td>113</td><td>0,46</td><td rowspan="12">1,3</td><td rowspan="12">0,22</td><td>750</td><td>70</td><td>0,60</td><td rowspan="12">до 1</td><td rowspan="12">0,22</td><td>960</td><td colspan="2">90</td><td>0,47</td><td rowspan="12">до 1</td></tr>
<tr><td>2</td><td>48</td><td>380</td><td rowspan="11">57</td><td>1,46</td><td>960</td><td rowspan="11">144</td><td>0,58</td><td>600</td><td rowspan="11">90</td><td>0,76</td><td>750</td><td colspan="2" rowspan="11">113</td><td>0,60</td></tr>
<tr><td>3</td><td>60</td><td>300</td><td>1,85</td><td>750</td><td>0,74</td><td>480</td><td>0,95</td><td>600</td><td>0,76</td></tr>
<tr><td>4</td><td>75</td><td>240</td><td>2,31</td><td>600</td><td>0,92</td><td>380</td><td>1,2</td><td>480</td><td>0,95</td></tr>
<tr><td>5</td><td>96</td><td>190</td><td>2,92</td><td>480</td><td>1,16</td><td>300</td><td>1,51</td><td>380</td><td>1,2</td></tr>
<tr><td>6</td><td>120</td><td>150</td><td>3,7</td><td>380</td><td>1,46</td><td>240</td><td>1,9</td><td>300</td><td>1,51</td></tr>
<tr><td>7</td><td>150</td><td>120</td><td>4,63</td><td>300</td><td>1,85</td><td>190</td><td>2,39</td><td>240</td><td>1,9</td></tr>
<tr><td>8</td><td>190</td><td>96</td><td>5,78</td><td>240</td><td>2,31</td><td>150</td><td>3,03</td><td>190</td><td>2,39</td></tr>
<tr><td>9</td><td>240</td><td>75</td><td>7,4</td><td>190</td><td>2,92</td><td>120</td><td>3,79</td><td>150</td><td>3,03</td></tr>
<tr><td>10</td><td>300</td><td>60</td><td>9,26</td><td>150</td><td>3,7</td><td>96</td><td>4,73</td><td>120</td><td>3,79</td></tr>
<tr><td>11</td><td>380</td><td>48</td><td>11,57</td><td>120</td><td>4,63</td><td>75</td><td>6,06</td><td>96</td><td>4,73</td></tr>
<tr><td>12</td><td>480</td><td>38</td><td>14,6</td><td>96</td><td>5,76</td><td>60</td><td>7,57</td><td>75</td><td>6,06</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="4"></td><td>в</td><td colspan="5"></td><td>г</td><td></td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="9%"><col width="12%"><col width="20%"><col width="5%"><col width="3%"><col width="8%"><col width="7%"><col width="5%"><col width="3%"><col width="2%"><col width="2%"><col width="4%"><col width="9%"></colgroup>
<tr><td colspan="14">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Растачивание отверстий, Rz 2,5, 1Т9 - 1Т8 квалитет</td></tr>
<tr><td colspan="14">Сталь, чугун, медные сплавы и алюминиевые Резцы из стали Р6М5 и с Среднесерийное производство пластинками Т15К6, ВК6</td></tr>
<tr><td colspan="11">Карта 101</td><td colspan="3">Лист 2</td></tr>
<tr><td colspan="14">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="9">Группы стали и предела прочности</td><td rowspan="9">Инструмент</td><td rowspan="5">Из быстрорежущей стали Р6М5</td><td>Группа стали</td><td colspan="4">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="6">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td>0,59 - 0,74</td><td>свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="3">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td></td><td rowspan="3">1,25</td><td colspan="2" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td>1,0</td></tr>
<tr><td></td></tr>
<tr><td rowspan="4">С пластинками из твердого сплава Т5К10</td><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td>0,59 - 0,74</td><td>свыше 0,74</td><td colspan="6" rowspan="4">-</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td></td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td></tr>
<tr><td></td></tr>
<tr><td colspan="3" rowspan="4">Твердости чугуна</td><td>Твердость чугуна НВ, ГПа</td><td colspan="4">до 2,15</td><td colspan="6">свыше 2,15</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="6" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td colspan="3" rowspan="5">Группы медных сплавов и твердости</td><td>Группа сплавов</td><td colspan="4">Гомогенные</td><td colspan="6">Гетерогенные</td></tr>
<tr><td>Твердость НВ, ГПа</td><td colspan="4">0,59 - 0,88</td><td colspan="4">0,98 - 1,37</td><td colspan="2">1,47 - 2,45</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4" rowspan="3">0,55</td><td colspan="4"></td><td colspan="2" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td>Группы алюминиевых</td><td colspan="2">Группа сплавов</td><td>Силумин и литейные сплавы</td><td colspan="10">Дюралюминий</td></tr>
<tr><td rowspan="2">сплавов и твердости</td><td colspan="2">Твердость НВ, ГПа</td><td>до 0,64</td><td colspan="10">до 0,98</td></tr>
<tr><td colspan="2">Коэффициент</td><td>0,75</td><td colspan="10">0,7</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="6%"><col width="7%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="3%"><col width="4%"><col width="4%"><col width="2%"><col width="1%"><col width="6%"><col width="3%"></colgroup>
<tr><td colspan="18">Основное время на 100 мм расчетной длины Растачивание отверстий, Rz 1,25, 1Т7 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="18" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Резцы из стали Р6М5 и с пластинками Т15К6, ВК6</td></tr>
<tr><td colspan="4">Карта 102</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="5">N позиции</td><td>Диаметр обрабатываемого</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l ,</td><td colspan="10">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td>отверстия D,</td><td>1 l , мм</td><td colspan="21">Режущий инструмент</td></tr>
<tr><td rowspan="3">мм, до</td><td rowspan="3">2</td><td colspan="5">Р6М5</td><td colspan="5">Т15К6</td><td colspan="5">ВК6</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>1</td><td>30</td><td rowspan="12">1,0</td><td rowspan="12">2,0</td><td rowspan="12">0,1</td><td>750</td><td>70</td><td>1,33</td><td rowspan="12">1</td><td rowspan="12">0,1</td><td>1200</td><td>113</td><td>0,83</td><td rowspan="12">1</td><td rowspan="12">0,12</td><td>960</td><td>90</td><td>0,86</td><td rowspan="12">1</td><td rowspan="12">0,12</td><td>1200</td><td colspan="2">113</td><td>0,69</td><td rowspan="12">1</td></tr>
<tr><td>2</td><td>48</td><td>600</td><td rowspan="11">90</td><td>1,66</td><td>960</td><td>145</td><td>1,04</td><td>750</td><td rowspan="11">113</td><td>1,11</td><td>960</td><td colspan="2" rowspan="11">145</td><td>0,86</td></tr>
<tr><td>3</td><td>60</td><td>480</td><td>2,08</td><td>750</td><td rowspan="10">145</td><td>1,33</td><td>600</td><td>1,39</td><td>750</td><td>1,11</td></tr>
<tr><td>4</td><td>75</td><td>380</td><td>2,63</td><td>600</td><td>1,66</td><td>480</td><td>1,73</td><td>600</td><td>1,39</td></tr>
<tr><td>5</td><td>96</td><td>300</td><td>3,33</td><td>480</td><td>2,08</td><td>380</td><td>2,19</td><td>480</td><td>1,73</td></tr>
<tr><td>6</td><td>120</td><td>240</td><td>4,17</td><td>380</td><td>2,63</td><td>300</td><td>2,77</td><td>380</td><td>2,19</td></tr>
<tr><td>7</td><td>150</td><td>190</td><td>5,26</td><td>300</td><td>3,33</td><td>240</td><td>3,47</td><td>300</td><td>2,77</td></tr>
<tr><td>8</td><td>190</td><td>150</td><td>6,66</td><td>240</td><td>4,17</td><td>190</td><td>4,38</td><td>240</td><td>3,47</td></tr>
<tr><td>9</td><td>240</td><td>120</td><td>8,33</td><td>190</td><td>5,26</td><td>150</td><td>5,55</td><td>190</td><td>4,38</td></tr>
<tr><td>10</td><td>300</td><td>96</td><td>10,4</td><td>150</td><td>6,66</td><td>120</td><td>6,94</td><td>150</td><td>5,55</td></tr>
<tr><td>11</td><td>380</td><td>75</td><td>13,3</td><td>120</td><td>8,33</td><td>96</td><td>8,68</td><td>120</td><td>6,94</td></tr>
<tr><td>12</td><td>480</td><td>60</td><td>16,6</td><td>96</td><td>10,4</td><td>75</td><td>11,1</td><td>96</td><td>8,68</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="4"></td><td>в</td><td colspan="5"></td><td>г</td><td></td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="9%"><col width="12%"><col width="20%"><col width="5%"><col width="3%"><col width="8%"><col width="7%"><col width="5%"><col width="3%"><col width="2%"><col width="2%"><col width="4%"><col width="9%"></colgroup>
<tr><td colspan="14">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Растачивание отверстий, Rz 1,25, 1Т7 квалитет</td></tr>
<tr><td colspan="14">Сталь, чугун, медные сплавы и алюминиевые Резцы из стали Р6М5 и с Среднесерийное производство пластинками Т15К6, ВК6</td></tr>
<tr><td colspan="11">Карта 102</td><td colspan="3">Лист 2</td></tr>
<tr><td colspan="14">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="9">Группы стали и предела прочности</td><td rowspan="9">Инструмент</td><td rowspan="5">Из быстрорежущей стали Р6М5</td><td>Группа стали</td><td colspan="4">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="6">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td>0,59 - 0,74</td><td>свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="3">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td></td><td rowspan="3">1,25</td><td colspan="2" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td>1,0</td></tr>
<tr><td></td></tr>
<tr><td rowspan="4">С пластинками из твердого сплава Т5К10</td><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td>0,59 - 0,74</td><td>свыше 0,74</td><td colspan="6" rowspan="4">-</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td></td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td></tr>
<tr><td></td></tr>
<tr><td colspan="3" rowspan="4">Твердости чугуна</td><td>Твердость чугуна НВ, ГПа</td><td colspan="4">до 2,15</td><td colspan="6">свыше 2,15</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="6" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td colspan="3" rowspan="5">Группы медных сплавов и твердости</td><td>Группа сплавов</td><td colspan="4">Гомогенные</td><td colspan="6">Гетерогенные</td></tr>
<tr><td>Твердость НВ, ГПа</td><td colspan="4">0,59 - 0,88</td><td colspan="4">0,98 - 1,37</td><td colspan="2">1,47 - 2,45</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4" rowspan="3">0,55</td><td colspan="4"></td><td colspan="2" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td>Группы алюминиевых</td><td colspan="2">Группа сплавов</td><td>Силумин и литейные сплавы</td><td colspan="10">Дюралюминий</td></tr>
<tr><td rowspan="2">сплавов и твердости</td><td colspan="2">Твердость НВ, ГПа</td><td>до 0,64</td><td colspan="10">до 0,98</td></tr>
<tr><td colspan="2">Коэффициент</td><td>0,75</td><td colspan="10">0,7</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="4%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="7%"><col width="4%"></colgroup>
<tr><td colspan="13">Основное время на 100 мм расчетной длины Продольное и поперечное точение, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Суппорт планшайбы Резцы с пластинками Т15К6, ВК8 и из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 103</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="5">N позиции</td><td rowspan="2">Диаметр обрабатываемой поверхности D, мм,</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , 1</td><td colspan="5">Сталь конструкционная углеродистая, сигма = в 0,59 - 0,74 ГПа</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="4">l , мм 2</td><td colspan="16">Режущий инструмент</td></tr>
<tr><td rowspan="3">до</td><td colspan="5">Т5К10</td><td colspan="5">ВК8</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>1</td><td rowspan="3">120</td><td>3</td><td>3</td><td>0,6</td><td rowspan="3">150</td><td rowspan="11">57</td><td>1,11</td><td>2,5</td><td>0,7</td><td rowspan="3">150</td><td rowspan="11">57</td><td>0,95</td><td>1,5</td><td>0,56</td><td rowspan="3">150</td><td colspan="2" rowspan="11">57</td><td>1,19</td><td>0,5</td></tr>
<tr><td>2</td><td>5</td><td>5</td><td>0,5</td><td>1,33</td><td>3,5</td><td>0,56</td><td>1,19</td><td>2,2</td><td>0,45</td><td>1,48</td><td>1,5</td></tr>
<tr><td>3</td><td>8</td><td>7</td><td>0,4</td><td>1,66</td><td>5,0</td><td>0,45</td><td>1,48</td><td>3,2</td><td>0,35</td><td>1,9</td><td>2,0</td></tr>
<tr><td>4</td><td rowspan="3">150</td><td>3</td><td>3</td><td>0,6</td><td rowspan="3">120</td><td>1,39</td><td>2,5</td><td>0,7</td><td rowspan="3">120</td><td>1,19</td><td>1,5</td><td>0,56</td><td rowspan="3">120</td><td>1,49</td><td>0,5</td></tr>
<tr><td>5</td><td>5</td><td>5</td><td>0,5</td><td>1,66</td><td>3,5</td><td>0,56</td><td>1,49</td><td>2,2</td><td>0,45</td><td>1,85</td><td>1,5</td></tr>
<tr><td>6</td><td>8</td><td>7</td><td>0,4</td><td>2,08</td><td>5,0</td><td>0,45</td><td>1,85</td><td>3,2</td><td>0,35</td><td>2,38</td><td>2,0</td></tr>
<tr><td>7</td><td rowspan="3">190</td><td>3</td><td>3</td><td>0,6</td><td rowspan="3">96</td><td>1,73</td><td>2,5</td><td>0,7</td><td rowspan="3">96</td><td>1,49</td><td>1,5</td><td>0,56</td><td rowspan="3">96</td><td>1,86</td><td>0,5</td></tr>
<tr><td>8</td><td>5</td><td>5</td><td>0,5</td><td>2,08</td><td>3,5</td><td>0,56</td><td>1,86</td><td>2,2</td><td>0,45</td><td>2,31</td><td>1,5</td></tr>
<tr><td>9</td><td>8</td><td>7</td><td>0,4</td><td>2,6</td><td>5,0</td><td>0,45</td><td>2,31</td><td>3,2</td><td>0,35</td><td>2,97</td><td>2,0</td></tr>
<tr><td>10</td><td rowspan="2">240</td><td>3</td><td>3</td><td>0,6</td><td rowspan="2">75</td><td>2,22</td><td>2,5</td><td>0,7</td><td rowspan="2">75</td><td>1,9</td><td>1,5</td><td>0,56</td><td rowspan="2">75</td><td>2,38</td><td>0,5</td></tr>
<tr><td>11</td><td>5</td><td>5</td><td>0,5</td><td>2,66</td><td>3,5</td><td>0,56</td><td>2,38</td><td>2,2</td><td>0,45</td><td>2,96</td><td>1,5</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="5"></td><td>в</td><td></td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="4%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="7%"><col width="4%"></colgroup>
<tr><td colspan="13">Основное время на 100 мм расчетной длины Продольное и поперечное точение, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Суппорт планшайбы Резцы с пластинками Т5К10, ВК8 и из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 103</td><td colspan="3">Лист 2</td></tr>
<tr><td rowspan="5">N позиции</td><td rowspan="2">Диаметр обрабатываемой поверхности D, мм,</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , 1</td><td colspan="5">Сталь конструкционная углеродистая, сигма = в 0,59 - 0,74 ГПа</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="4">l , мм 2</td><td colspan="16">Режущий инструмент</td></tr>
<tr><td rowspan="3">до</td><td colspan="5">Т5К10</td><td colspan="5">ВК8</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>12</td><td>240</td><td>8</td><td>7</td><td>0,4</td><td>75</td><td rowspan="13">57</td><td>3,33</td><td>5,0</td><td>0,45</td><td>75</td><td rowspan="13">57</td><td>2,96</td><td>3,2</td><td>0,35</td><td>75</td><td colspan="2" rowspan="13">57</td><td>3,81</td><td>2,0</td></tr>
<tr><td>13</td><td rowspan="3">300</td><td>3</td><td>3</td><td>0,6</td><td rowspan="3">60</td><td>2,77</td><td>2,5</td><td>0,7</td><td rowspan="3">60</td><td>2,38</td><td>1,5</td><td>0,56</td><td rowspan="3">60</td><td>2,97</td><td>0,5</td></tr>
<tr><td>14</td><td>5</td><td>5</td><td>0,5</td><td>3,33</td><td>3,5</td><td>0,56</td><td>2,97</td><td>2,2</td><td>0,45</td><td>3,7</td><td>1,5</td></tr>
<tr><td>15</td><td>8</td><td>7</td><td>0,4</td><td>4,16</td><td>5,0</td><td>0,45</td><td>3,7</td><td>3,2</td><td>0,35</td><td>4,76</td><td>2,0</td></tr>
<tr><td>16</td><td rowspan="3">380</td><td>3</td><td>3</td><td>0,6</td><td rowspan="3">48</td><td>3,47</td><td>2,5</td><td>0,7</td><td rowspan="3">48</td><td>2,97</td><td>1,5</td><td>0,56</td><td rowspan="3">48</td><td>3,72</td><td>0,5</td></tr>
<tr><td>17</td><td>5</td><td>5</td><td>0,5</td><td>4,16</td><td>3,5</td><td>0,56</td><td>3,72</td><td>2,2</td><td>0,45</td><td>4,63</td><td>1,5</td></tr>
<tr><td>18</td><td>8</td><td>7</td><td>0,4</td><td>5,21</td><td>5,0</td><td>0,45</td><td>4,63</td><td>3,2</td><td>0,35</td><td>5,95</td><td>2,0</td></tr>
<tr><td>19</td><td rowspan="3">480</td><td>3</td><td>3</td><td>0,6</td><td rowspan="3">38</td><td>4,38</td><td>2,5</td><td>0,7</td><td rowspan="3">38</td><td>3,76</td><td>1,5</td><td>0,56</td><td rowspan="3">38</td><td>4,7</td><td>0,5</td></tr>
<tr><td>20</td><td>5</td><td>5</td><td>0,5</td><td>5,26</td><td>3,5</td><td>0,56</td><td>4,7</td><td>2,2</td><td>0,45</td><td>5,85</td><td>1,5</td></tr>
<tr><td>21</td><td>8</td><td>7</td><td>0,4</td><td>6,58</td><td>5,0</td><td>0,45</td><td>5,85</td><td>3,2</td><td>0,35</td><td>7,52</td><td>2,0</td></tr>
<tr><td>22</td><td rowspan="3">600</td><td>3</td><td>3</td><td>0,6</td><td rowspan="3">30</td><td>5,55</td><td>2,5</td><td>0,7</td><td rowspan="3">30</td><td>4,75</td><td>1,5</td><td>0,56</td><td rowspan="3">30</td><td>5,94</td><td>0,5</td></tr>
<tr><td>23</td><td>5</td><td>5</td><td>0,5</td><td>6,66</td><td>3,5</td><td>0,56</td><td>5,94</td><td>2,2</td><td>0,45</td><td>7,4</td><td>1,5</td></tr>
<tr><td>24</td><td>8</td><td>7</td><td>0,4</td><td>8,33</td><td>5,0</td><td>0,45</td><td>7,4</td><td>3,2</td><td>0,35</td><td>9,5</td><td>2,0</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="5"></td><td>в</td><td></td></tr>
</table>



```text
┌────────────────────────────────────────────────────────────┬──────────────────────────────┐
│Основное время на 100 мм расчетной длины                    │Горизонтально-расточные станки│
│Продольное и поперечное точение, Rz 80, 1Т14 - 1Т12 квалитет├──────────────────────────────┤
│Сталь, чугун, медные сплавы и алюминиевые                   │      Суппорт планшайбы       │
│Среднесерийное производство                                 │Резцы с пластинками Т5К10, ВК8│
│                                                            │       и из стали Р6М5        │
│                                                            ├────────────────┬─────────────┤
│                                                            │   Карта 103    │   Лист 3    │
├────────────────────────────────────────────────────────────┴────────────────┴─────────────┤
│Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:│
├─────────┬───────┬──────────┬─────────────────┬────────────────────┬───────────────────────┤
│Группы   │Инстру-│Из быстро-│Группа стали     │   Углеродистые,    │    Марганцовистые,    │
│стали и  │мент   │режущей   │                 │     хромистые,     │ хромомарганцовистые,  │
│предела  │       │стали Р6М5│                 │     никелевые,     │  хромомолибденовые и  │
│прочности│       │          │                 │   хромоникелевые   │     близкие к ним     │
│         │       │          ├─────────────────┼───────┬──────┬─────┼───────┬───────┬───────┤
│         │       │          │Предел прочности │до 0,59│0,59 -│свыше│до 0,59│0,59 - │свыше  │
│         │       │          │сигма , ГПа      │       │0,74  │0,74 │       │0,74   │0,74   │
│         │       │          │     в           │       │      │     │       │       │       │
│         │       │          ├─────────────────┼───────┼──────┼─────┼───────┼───────┼───────┤
│         │       │          │                 │       │┌───┐ │     │       │       │       │
│         │       │          │Коэффициент      │0,8    ││1,0│ │1,25 │1,1    │1,2    │1,35   │
│         │       │          │                 │       │└───┘ │     │       │       │       │
│         │       ├──────────┼─────────────────┼───────┼──────┼─────┼───────┴───────┴───────┤
│         │       │С пластин-│Предел прочности │до 0,59│0,59 -│свыше│           -           │
│         │       │ками из   │сигма , ГПа      │       │0,74  │0,74 │                       │
│         │       │твердого  │     в           │       │      │     │                       │
│         │       │сплава    ├─────────────────┼───────┼──────┼─────┤                       │
│         │       │Т5К10     │                 │       │┌───┐ │     │                       │
│         │       │          │Коэффициент      │0,8    ││1,0│ │1,25 │                       │
│         │       │          │                 │       │└───┘ │     │                       │
├─────────┴───────┴──────────┼─────────────────┼───────┴──────┴─────┼───────────────────────┤
│Твердости чугуна            │Твердость чугуна │до 2,15             │свыше 2,15             │
│                            │НВ, ГПа          │                    │                       │
│                            ├─────────────────┼────────────────────┼───────────────────────┤
│                            │                 │┌───┐               │                       │
│                            │Коэффициент      ││1,0│               │1,25                   │
│                            │                 │└───┘               │                       │
├────────────────────────────┼─────────────────┼────────────────────┼───────────────────────┤
│Группы медных сплавов и     │Группа сплавов   │Гомогенные          │     Гетерогенные      │
│твердости                   ├─────────────────┼────────────────────┼───────────┬───────────┤
│                            │Твердость НВ, ГПа│0,59 - 0,88         │0,98 - 1,37│1,47 - 2,45│
│                            ├─────────────────┼────────────────────┼───────────┼───────────┤
│                            │                 │                    │┌───┐      │           │
│                            │Коэффициент      │0,55                ││1,0│      │1,25       │
│                            │                 │                    │└───┘      │           │
├─────────┬──────────────────┼─────────────────┼────────────────────┴───────────┴───────────┤
│Группы   │Группа сплавов    │Силумин и        │Дюралюминий                                 │
│алюминие-│                  │литейные сплавы  │                                            │
│вых      ├──────────────────┼─────────────────┼────────────────────────────────────────────┤
│сплавов и│Твердость НВ, ГПа │до 0,64          │до 0,98                                     │
│твердости├──────────────────┼─────────────────┼────────────────────────────────────────────┤
│         │Коэффициент       │0,75             │0,7                                         │
├─────────┴──────────────────┼─────────────────┼────────────────────────────────────────────┤
│Вид обработки               │Предельное и по- │Растачивание                                │
│                            │перечное точение │                                            │
│                            ├─────────────────┴────────────────────────────────────────────┤
│                            │                         Коэффициент                          │
│                            ├─────────────────┬────────────────────────────────────────────┤
│                            │┌───┐            │                                            │
│                            ││0,1│            │1,06                                        │
│                            │└───┘            │                                            │
├────────────────────────────┼─────────────────┼─────────────────────┬──────────────────────┤
│Состояния обрабатываемой    │Состояние        │без корки и удара    │по корке и на удар    │
│поверхности                 │обрабатываемой   │                     │                      │
│                            │поверхности      │                     │                      │
│                            ├─────────────────┼─────────────────────┼──────────────────────┤
│                            │                 │┌───┐                │                      │
│                            │Коэффициент      ││1,0│                │1,2                   │
│                            │                 │└───┘                │                      │
└────────────────────────────┴─────────────────┴─────────────────────┴──────────────────────┘
```



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="4%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="7%"><col width="4%"></colgroup>
<tr><td colspan="13">Основное время на 100 мм расчетной длины Продольное и поперечное точение, Rz 40, 1Т11 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Суппорт планшайбы Резцы с пластинками Т15К6, ВК6 и из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 104</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="5">N позиции</td><td rowspan="2">Диаметр обрабатываемой поверхности D, мм,</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , 1</td><td colspan="5">Сталь конструкционная углеродистая, сигма = в 0,59 - 0,74 ГПа</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="4">l , мм 2</td><td colspan="16">Режущий инструмент</td></tr>
<tr><td rowspan="3">до</td><td colspan="5">Т15К6</td><td colspan="5">ВК6</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>1</td><td>120</td><td rowspan="8">1</td><td rowspan="8">2</td><td rowspan="8">0,35</td><td>380</td><td rowspan="8">142</td><td>0,75</td><td rowspan="8">2,2</td><td rowspan="8">0,45</td><td>240</td><td rowspan="8">90</td><td>0,92</td><td rowspan="8">1,0</td><td rowspan="8">0,50</td><td>240</td><td colspan="2" rowspan="8">90</td><td>0,83</td><td rowspan="8">2,1</td></tr>
<tr><td>2</td><td>150</td><td>300</td><td>0,95</td><td>190</td><td>1,17</td><td>190</td><td>1,05</td></tr>
<tr><td>3</td><td>190</td><td>240</td><td>1,19</td><td>150</td><td>1,48</td><td>150</td><td>1,33</td></tr>
<tr><td>4</td><td>240</td><td>190</td><td>1,5</td><td>120</td><td>1,85</td><td>120</td><td>1,66</td></tr>
<tr><td>5</td><td>300</td><td>150</td><td>1,9</td><td>96</td><td>2,31</td><td>96</td><td>2,08</td></tr>
<tr><td>6</td><td>380</td><td>120</td><td>2,38</td><td>75</td><td>2,96</td><td>75</td><td>2,66</td></tr>
<tr><td>7</td><td>480</td><td>96</td><td>2,97</td><td>60</td><td>3,7</td><td>60</td><td>3,33</td></tr>
<tr><td>8</td><td>600</td><td>75</td><td>3,81</td><td>48</td><td>4,63</td><td>48</td><td>4,16</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="5"></td><td>в</td><td></td></tr>
</table>



```text
┌──────────────────────────────────────────┬──────────────────────────────┐
│Основное время на 100 мм расчетной длины  │Горизонтально-расточные станки│
│Продольное и поперечное точение,          ├──────────────────────────────┤
│Rz 40, 1Т11 квалитет                      │      Суппорт планшайбы       │
│Сталь, чугун, медные сплавы и алюминиевые │Резцы с пластинками Т15К6, ВК6│
│Среднесерийное производство               │       и из стали Р6М5        │
│                                          ├────────────────┬─────────────┤
│                                          │   Карта 104    │   Лист 2    │
├──────────────────────────────────────────┴────────────────┴─────────────┤
│Поправочные коэффициенты на время обработки для измененных условий работы│
│                            в зависимости от:                            │
├────────────────────────┬─────────────────┬───────┬───────────┬──────────┤
│Предела прочности стали │Предел прочности │до 0,59│0,59 - 0,74│свыше 0,74│
│                        │сигма , ГПа      │       │           │          │
│                        │     в           │       │           │          │
│                        ├─────────────────┼───────┼───────────┼──────────┤
│                        │                 │       │┌───┐      │          │
│                        │Коэффициент      │0,8    ││1,0│      │1,25      │
│                        │                 │       │└───┘      │          │
├────────────────────────┼─────────────────┼───────┴─────┬─────┴──────────┤
│Твердости чугуна        │Твердость чугуна │до 2,15      │свыше 2,15      │
│                        │НВ, ГПа          │             │                │
│                        ├─────────────────┼─────────────┼────────────────┤
│                        │                 │┌───┐        │                │
│                        │Коэффициент      ││1,0│        │1,25            │
│                        │                 │└───┘        │                │
├────────────────────────┼─────────────────┼─────────────┼────────────────┤
│Группы медных сплавов и │Группа сплавов   │Гомогенные   │  Гетерогенные  │
│твердости               ├─────────────────┼─────────────┼────────┬───────┤
│                        │Твердость НВ, ГПа│0,59 - 0,88  │0,98 -  │1,47 - │
│                        │                 │             │1,37    │2,45   │
│                        ├─────────────────┼─────────────┼────────┼───────┤
│                        │                 │             │┌───┐   │       │
│                        │Коэффициент      │0,55         ││1,0│   │1,25   │
│                        │                 │             │└───┘   │       │
├────────────────────────┼─────────────────┼─────────────┼────────┴───────┤
│Группы алюминиевых      │Группа сплавов   │Силумин и ли-│Дюралюминий     │
│сплавов и твердости     │                 │тейные сплавы│                │
│                        ├─────────────────┼─────────────┼────────────────┤
│                        │Твердость НВ, ГПа│до 0,64      │до 0,98         │
│                        ├─────────────────┼─────────────┼────────────────┤
│                        │Коэффициент      │0,75         │0,7             │
├────────────────────────┼─────────────────┴────┬────────┴────────────────┤
│Вида обработки          │Продольное и          │Растачивание             │
│                        │поперечное точение    │                         │
│                        ├──────────────────────┴─────────────────────────┤
│                        │                   Коэффициент                  │
│                        ├──────────────────────┬─────────────────────────┤
│                        │┌───┐                 │                         │
│                        ││0,1│                 │1,06                     │
│                        │└───┘                 │                         │
└────────────────────────┴──────────────────────┴─────────────────────────┘
```



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="4%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="7%"><col width="4%"></colgroup>
<tr><td colspan="13">Основное время на 100 мм расчетной длины Продольное и поперечное точение, Rz 2,5, 1Т9 - 1Т8 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Суппорт планшайбы Резцы с пластинками Т15К6, ВК6 и из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 105</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="5">N позиции</td><td rowspan="2">Диаметр обрабатываемой поверхности D, мм,</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , 1</td><td colspan="5">Сталь конструкционная углеродистая, сигма = в 0,59 - 0,74 ГПа</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="4">l , мм 2</td><td colspan="16">Режущий инструмент</td></tr>
<tr><td rowspan="3">до</td><td colspan="5">Т15К6</td><td colspan="5">ВК6</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>1</td><td>120</td><td rowspan="8">1,0</td><td rowspan="8">2</td><td rowspan="8">0,22</td><td>480</td><td rowspan="8">180</td><td>1,04</td><td rowspan="8">1</td><td rowspan="8">0,22</td><td>480</td><td rowspan="8">180</td><td>0,94</td><td rowspan="8">1</td><td rowspan="8">0,22</td><td>380</td><td colspan="2" rowspan="8">140</td><td>1,19</td><td rowspan="8">1</td></tr>
<tr><td>2</td><td>150</td><td>380</td><td>1,31</td><td>380</td><td>1,19</td><td>300</td><td>1,51</td></tr>
<tr><td>3</td><td>190</td><td>300</td><td>1,66</td><td>300</td><td>1,51</td><td>240</td><td>1,90</td></tr>
<tr><td>4</td><td>240</td><td>240</td><td>2,08</td><td>240</td><td>1,90</td><td>190</td><td>2,39</td></tr>
<tr><td>5</td><td>300</td><td>190</td><td>2,63</td><td>190</td><td>2,39</td><td>150</td><td>3,03</td></tr>
<tr><td>6</td><td>380</td><td>150</td><td>3,33</td><td>150</td><td>3,03</td><td>120</td><td>3,78</td></tr>
<tr><td>7</td><td>480</td><td>120</td><td>4,16</td><td>120</td><td>3,78</td><td>96</td><td>4,73</td></tr>
<tr><td>8</td><td>600</td><td>96</td><td>5,20</td><td>96</td><td>4,73</td><td>75</td><td>6,06</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="5"></td><td>в</td><td></td></tr>
</table>



```text
┌──────────────────────────────────────────┬──────────────────────────────┐
│Основное время на 100 мм расчетной длины  │Горизонтально-расточные станки│
│Продольное и поперечное точение,          ├──────────────────────────────┤
│Rz 2,5, 1Т9 - 1Т8 квалитет                │      Суппорт планшайбы       │
│Сталь, чугун, медные сплавы и алюминиевые │Резцы с пластинками Т15К6, ВК6│
│Среднесерийное производство               │       и из стали Р6М5        │
│                                          ├────────────────┬─────────────┤
│                                          │   Карта 105    │   Лист 2    │
├──────────────────────────────────────────┴────────────────┴─────────────┤
│Поправочные коэффициенты на время обработки для измененных условий работы│
│                            в зависимости от:                            │
├────────────────────────┬─────────────────┬───────┬───────────┬──────────┤
│Предела прочности стали │Предел прочности │до 0,59│0,59 - 0,74│свыше 0,74│
│                        │сигма , ГПа      │       │           │          │
│                        │     в           │       │           │          │
│                        ├─────────────────┼───────┼───────────┼──────────┤
│                        │                 │       │┌───┐      │          │
│                        │Коэффициент      │0,8    ││1,0│      │1,25      │
│                        │                 │       │└───┘      │          │
├────────────────────────┼─────────────────┼───────┴─────┬─────┴──────────┤
│Твердости чугуна        │Твердость чугуна │до 2,15      │свыше 2,15      │
│                        │НВ, ГПа          │             │                │
│                        ├─────────────────┼─────────────┼────────────────┤
│                        │                 │┌───┐        │                │
│                        │Коэффициент      ││1,0│        │1,25            │
│                        │                 │└───┘        │                │
├────────────────────────┼─────────────────┼─────────────┼────────────────┤
│Группы медных сплавов и │Группа сплавов   │Гомогенные   │  Гетерогенные  │
│твердости               ├─────────────────┼─────────────┼────────┬───────┤
│                        │Твердость НВ, ГПа│0,59 - 0,88  │0,98 -  │1,47 - │
│                        │                 │             │1,37    │2,45   │
│                        ├─────────────────┼─────────────┼────────┼───────┤
│                        │                 │             │┌───┐   │       │
│                        │Коэффициент      │0,8          ││1,0│   │1,25   │
│                        │                 │             │└───┘   │       │
├────────────────────────┼─────────────────┼─────────────┼────────┴───────┤
│Группы алюминиевых      │Группа сплавов   │Силумин и ли-│Дюралюминий     │
│сплавов и твердости     │                 │тейные сплавы│                │
│                        ├─────────────────┼─────────────┼────────────────┤
│                        │Твердость НВ, ГПа│до 0,64      │до 0,98         │
│                        ├─────────────────┼─────────────┼────────────────┤
│                        │Коэффициент      │0,75         │0,7             │
├────────────────────────┼─────────────────┴─────┬───────┴────────────────┤
│Вида обработки          │Продольное и           │Растачивание            │
│                        │поперечное точение     │                        │
│                        ├───────────────────────┴────────────────────────┤
│                        │                    Коэффициент                 │
│                        ├───────────────────────┬────────────────────────┤
│                        │┌───┐                  │                        │
│                        ││0,1│                  │1,06                    │
│                        │└───┘                  │                        │
└────────────────────────┴───────────────────────┴────────────────────────┘
```



<table>
<colgroup><col width="4%"><col width="7%"><col width="7%"><col width="8%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="7%"><col width="4%"><col width="5%"><col width="5%"><col width="3%"><col width="2%"><col width="7%"><col width="4%"></colgroup>
<tr><td colspan="13">Основное время на 100 мм расчетной длины Продольное и поперечное точение, Rz 1,25, 1Т7 квалитет</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Суппорт планшайбы Резцы с пластинками Т15К6, ВК6 и из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 106</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="5">N позиции</td><td rowspan="2">Диаметр обрабатываемой поверхности D, мм,</td><td rowspan="5">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , 1</td><td colspan="5">Сталь конструкционная углеродистая, сигма = в 0,59 - 0,74 ГПа</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="6">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="4">l , мм 2</td><td colspan="16">Режущий инструмент</td></tr>
<tr><td rowspan="3">до</td><td colspan="5">Т15К6</td><td colspan="5">ВК6</td><td colspan="6">Р6М5</td></tr>
<tr><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">N , р кВт</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>1</td><td>120</td><td rowspan="8">1</td><td rowspan="8">2</td><td rowspan="8">0,12</td><td>480</td><td rowspan="8">180</td><td>1,73</td><td rowspan="8">1,9</td><td rowspan="8">0,12</td><td>380</td><td rowspan="8">380</td><td>2,19</td><td rowspan="8">2,2</td><td rowspan="8">0,15</td><td>380</td><td colspan="2" rowspan="8">140</td><td>1,75</td><td rowspan="8">2,0</td></tr>
<tr><td>2</td><td>150</td><td>380</td><td>2,19</td><td>300</td><td>2,77</td><td>300</td><td>2,22</td></tr>
<tr><td>3</td><td>190</td><td>300</td><td>2,77</td><td>240</td><td>3,47</td><td>240</td><td>2,77</td></tr>
<tr><td>4</td><td>240</td><td>240</td><td>3,47</td><td>190</td><td>4,38</td><td>190</td><td>3,51</td></tr>
<tr><td>5</td><td>300</td><td>190</td><td>4,38</td><td>150</td><td>5,55</td><td>150</td><td>4,44</td></tr>
<tr><td>6</td><td>380</td><td>150</td><td>5,55</td><td>120</td><td>6,94</td><td>120</td><td>5,55</td></tr>
<tr><td>7</td><td>480</td><td>120</td><td>6,94</td><td>96</td><td>8,68</td><td>96</td><td>6,94</td></tr>
<tr><td>8</td><td>600</td><td>96</td><td>8,68</td><td>75</td><td>11,1</td><td>75</td><td>8,88</td></tr>
<tr><td colspan="7">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="5"></td><td>в</td><td></td></tr>
</table>



```text
┌──────────────────────────────────────────┬──────────────────────────────┐
│Основное время на 100 мм расчетной длины  │Горизонтально-расточные станки│
│Продольное и поперечное точение, Rz 1,25, ├──────────────────────────────┤
│1Т7 квалитет                              │      Суппорт планшайбы       │
│Сталь, чугун, медные сплавы и алюминиевые │Резцы с пластинками Т15К6, ВК6│
│Среднесерийное производство               │       и из стали Р6М5        │
│                                          ├───────────────┬──────────────┤
│                                          │   Карта 106   │    Лист 2    │
├──────────────────────────────────────────┴───────────────┴──────────────┤
│Поправочные коэффициенты на время обработки для измененных условий работы│
│                            в зависимости от:                            │
├────────────────────────┬─────────────────┬───────┬───────────┬──────────┤
│Предела прочности стали │Предел прочности │до 0,59│0,59 - 0,74│свыше 0,74│
│                        │сигма , ГПа      │       │           │          │
│                        │     в           │       │           │          │
│                        ├─────────────────┼───────┼───────────┼──────────┤
│                        │                 │       │┌───┐      │          │
│                        │Коэффициент      │0,8    ││1,0│      │1,25      │
│                        │                 │       │└───┘      │          │
├────────────────────────┼─────────────────┼───────┴─────┬─────┴──────────┤
│Твердости чугуна        │Твердость чугуна │до 2,15      │свыше 2,15      │
│                        │НВ, ГПа          │             │                │
│                        ├─────────────────┼─────────────┼────────────────┤
│                        │                 │┌───┐        │                │
│                        │Коэффициент      ││1,0│        │1,25            │
│                        │                 │└───┘        │                │
├────────────────────────┼─────────────────┼─────────────┼────────────────┤
│Группы медных сплавов и │Группа сплавов   │Гомогенные   │  Гетерогенные  │
│твердости               ├─────────────────┼─────────────┼────────┬───────┤
│                        │Твердость НВ, ГПа│0,59 - 0,88  │0,98 -  │1,47 - │
│                        │                 │             │1,37    │2,45   │
│                        ├─────────────────┼─────────────┼────────┼───────┤
│                        │                 │             │┌───┐   │       │
│                        │Коэффициент      │0,55         ││1,0│   │1,25   │
│                        │                 │             │└───┘   │       │
├────────────────────────┼─────────────────┼─────────────┼────────┴───────┤
│Группы алюминиевых      │Группа сплавов   │Силумин и ли-│Дюралюминий     │
│сплавов и твердости     │                 │тейные сплавы│                │
│                        ├─────────────────┼─────────────┼────────────────┤
│                        │Твердость НВ, ГПа│до 0,64      │до 0,98         │
│                        ├─────────────────┼─────────────┼────────────────┤
│                        │Коэффициент      │0,75         │0,7             │
├────────────────────────┼─────────────────┴─────┬───────┴────────────────┤
│Вида обработки          │Продольное и поперечное│Растачивание            │
│                        │точение                │                        │
│                        ├───────────────────────┴────────────────────────┤
│                        │                  Коэффициент                   │
│                        ├───────────────────────┬────────────────────────┤
│                        │┌───┐                  │                        │
│                        ││0,1│                  │1,06                    │
│                        │└───┘                  │                        │
└────────────────────────┴───────────────────────┴────────────────────────┘
```



<table>
<colgroup><col width="4%"><col width="9%"><col width="10%"><col width="6%"><col width="6%"><col width="6%"><col width="9%"><col width="6%"><col width="6%"><col width="3%"><col width="2%"><col width="9%"><col width="6%"><col width="3%"><col width="2%"><col width="6%"><col width="9%"></colgroup>
<tr><td colspan="10">Основное время на 10 мм расчетной длины Прорезка канавок</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="10" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Суппорт планшайбы Резцы из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 107</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр обрабатываемой поверхности D, мм, до</td><td>Величина врезания и перебега l , 1</td><td colspan="4">Сталь конструкционная углеродистая, сигма = в 0,59 - 0,74 ГПа</td><td colspan="5">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="5">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="2">l , мм 2</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td>S , о мм/ об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , о мм/ об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td><td>S , о мм/ об.</td><td colspan="2">n, об./ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>1</td><td>50</td><td rowspan="15">2</td><td rowspan="4">0,07</td><td>160</td><td>25</td><td>0,90</td><td rowspan="6">0,08</td><td>300</td><td colspan="2" rowspan="4">47</td><td>0,41</td><td rowspan="4">0,08</td><td colspan="2">600</td><td>94</td><td>0,21</td></tr>
<tr><td>2</td><td>75</td><td>100</td><td>23,5</td><td>1,43</td><td>200</td><td>0,62</td><td colspan="2">400</td><td>94</td><td>0,31</td></tr>
<tr><td>3</td><td>100</td><td>80</td><td>25</td><td>1,78</td><td>150</td><td>0,83</td><td colspan="2">400</td><td>125</td><td>0,31</td></tr>
<tr><td>4</td><td>125</td><td>63</td><td>25</td><td>2,26</td><td>120</td><td>1,04</td><td colspan="2">300</td><td>117</td><td>0,40</td></tr>
<tr><td>5</td><td>150</td><td>0,07</td><td>50</td><td rowspan="2">23</td><td rowspan="2">2,80</td><td>100</td><td colspan="2">47</td><td>1,0</td><td rowspan="7">0,1</td><td colspan="2">250</td><td>117</td><td>0,40</td></tr>
<tr><td>6</td><td>175</td><td>0,09</td><td>40</td><td>80</td><td colspan="2">44</td><td>1,25</td><td colspan="2">200</td><td>110</td><td>0,50</td></tr>
<tr><td>7</td><td>200</td><td rowspan="3">0,09</td><td>32</td><td>20</td><td>3,47</td><td rowspan="3">0,1</td><td>60</td><td colspan="2">38</td><td>1,65</td><td colspan="2">200</td><td>125</td><td>0,50</td></tr>
<tr><td>8</td><td>250</td><td rowspan="2">25</td><td rowspan="2">23,5</td><td rowspan="2">4,44</td><td>50</td><td colspan="2" rowspan="2">38,5</td><td>2,00</td><td colspan="2" rowspan="2">125</td><td>97</td><td rowspan="2">0,80</td></tr>
<tr><td>9</td><td>300</td><td>40</td><td>2,50</td><td>117</td></tr>
<tr><td>10</td><td>350</td><td>0,09</td><td>20</td><td>19</td><td rowspan="2">5,55</td><td rowspan="6">0,12</td><td>40</td><td colspan="2">44</td><td>2,10</td><td colspan="2">100</td><td>110</td><td>1,00</td></tr>
<tr><td>11</td><td>400</td><td>0,12</td><td>15</td><td>22</td><td>30</td><td colspan="2">38</td><td>2,80</td><td colspan="2">80</td><td>100</td><td>1,25</td></tr>
<tr><td>12</td><td>450</td><td rowspan="4">0,12</td><td rowspan="2">12,5</td><td>17,5</td><td rowspan="2">6,66</td><td rowspan="2">25</td><td colspan="2">35</td><td rowspan="2">3,33</td><td rowspan="4">0,12</td><td colspan="2">80</td><td>113</td><td>1,05</td></tr>
<tr><td>13</td><td>500</td><td>19,5</td><td colspan="2">39</td><td colspan="2">60</td><td>94</td><td>1,40</td></tr>
<tr><td>14</td><td>550</td><td rowspan="2">10</td><td>17</td><td rowspan="2">8,33</td><td rowspan="2">20</td><td colspan="2">34</td><td rowspan="2">4,16</td><td colspan="2" rowspan="2">50</td><td>86</td><td rowspan="2">1,65</td></tr>
<tr><td>15</td><td>600</td><td>19</td><td colspan="2">38</td><td>94</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="4"></td><td>в</td></tr>
</table>



<table>
<colgroup><col width="15%"><col width="22%"><col width="6%"><col width="4%"><col width="6%"><col width="9%"><col width="7%"><col width="10%"><col width="5%"><col width="10%"><col width="7%"></colgroup>
<tr><td colspan="11">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Прорезка канавок</td></tr>
<tr><td colspan="11">Сталь, чугун, медные сплавы и алюминиевые Суппорт планшайбы Среднесерийное производство Резцы из стали Р6М5</td></tr>
<tr><td colspan="9">Карта 107</td><td colspan="2">Лист 2</td></tr>
<tr><td colspan="11">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="5">Группы стали и предела прочности</td><td>Группа стали</td><td colspan="5">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="4">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td><td>до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="2"></td><td rowspan="3">1,25</td><td rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td rowspan="4">Твердости чугуна</td><td>Твердость чугуна НВ, ГПа</td><td colspan="4">до 2,15</td><td colspan="5">свыше 2,15</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="5" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td>Группы медных</td><td>Группа сплавов</td><td colspan="4">Гомогенные</td><td colspan="5">Гетерогенные</td></tr>
<tr><td rowspan="2">сплавов и твердости</td><td>Твердость НВ, ГПа</td><td colspan="4">0,59 - 0,88</td><td colspan="2">0,98 - 1,37</td><td colspan="3">1,47 - 2,45</td></tr>
<tr><td>Коэффициент</td><td colspan="4">0,55</td><td colspan="2">1,0</td><td colspan="3">1,25</td></tr>
<tr><td>Группы алюминиевых</td><td>Группа сплавов</td><td colspan="5">Силумин и литейные сплавы</td><td colspan="4">Дюралюминий</td></tr>
<tr><td rowspan="2">сплавов и твердости</td><td>Твердость НВ, ГПа</td><td colspan="5">до 0,64</td><td colspan="4">до 0,98</td></tr>
<tr><td>Коэффициент</td><td colspan="5">0,75</td><td colspan="4">0,7</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="9%"><col width="10%"><col width="9%"><col width="8%"><col width="9%"><col width="9%"><col width="8%"><col width="9%"><col width="9%"><col width="8%"><col width="9%"></colgroup>
<tr><td colspan="8">Основное время на 100 мм расчетной длины Подрезка торцов</td><td colspan="4">Горизонтально-расточные станки</td></tr>
<tr><td colspan="8" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="4">Суппорт планшайбы Резцы из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 108 Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="3">Диаметр обрабатываемой поверхности D, мм, до</td><td>Величина врезания и перебега l , 1</td><td colspan="3">Сталь конструкционная углеродистая, сигма = в 0,59 - 0,74 ГПа</td><td colspan="3">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="3">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="2">l , мм 2</td><td colspan="2">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="2">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="2">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td>S , м мм/мин.</td><td>v, м/мин.</td><td>S , м мм/мин.</td><td>v, м/мин.</td><td>S , м мм/мин.</td><td>v, м/мин.</td></tr>
<tr><td>1</td><td>75</td><td rowspan="9">2</td><td>3,8</td><td rowspan="9">30</td><td>2,63</td><td>5,2</td><td rowspan="9">28</td><td>1,9</td><td>17,5</td><td rowspan="9">60</td><td>0,57</td></tr>
<tr><td>2</td><td>125</td><td>3,2</td><td>3,10</td><td>4,0</td><td>2,5</td><td>14,0</td><td>0,70</td></tr>
<tr><td>3</td><td>150</td><td>2,75</td><td>3,60</td><td>3,7</td><td>2,7</td><td>11,5</td><td>0,87</td></tr>
<tr><td>4</td><td>175</td><td>2,45</td><td>4,10</td><td>3,3</td><td>3,0</td><td>10,0</td><td>1,0</td></tr>
<tr><td>5</td><td>200</td><td>2,15</td><td>4,65</td><td>2,9</td><td>3,45</td><td>9,0</td><td>1,10</td></tr>
<tr><td>6</td><td>225</td><td>1,95</td><td>5,13</td><td>2,6</td><td>3,85</td><td>8,0</td><td>1,25</td></tr>
<tr><td>7</td><td>250</td><td>1,75</td><td>5,70</td><td>2,2</td><td>4,65</td><td>7,0</td><td>1,43</td></tr>
<tr><td>8</td><td>275</td><td>1,5</td><td>6,65</td><td>2,0</td><td>5,0</td><td>6,5</td><td>1,54</td></tr>
<tr><td>9</td><td>300</td><td>1,35</td><td>7,40</td><td>1,8</td><td>5,55</td><td>6,0</td><td>1,65</td></tr>
<tr><td colspan="5">Индекс</td><td>а</td><td colspan="2"></td><td>б</td><td colspan="2"></td><td>в</td></tr>
</table>



<table>
<colgroup><col width="15%"><col width="22%"><col width="6%"><col width="4%"><col width="6%"><col width="9%"><col width="7%"><col width="10%"><col width="5%"><col width="10%"><col width="7%"></colgroup>
<tr><td colspan="11">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Подрезка торцов</td></tr>
<tr><td colspan="11">Сталь, чугун, медные сплавы и алюминиевые Суппорт планшайбы Среднесерийное производство Резцы из стали Р6М5</td></tr>
<tr><td colspan="9">Карта 108</td><td colspan="2">Лист 2</td></tr>
<tr><td colspan="11">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="5">Группы стали и предела прочности</td><td>Группа стали</td><td colspan="5">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="4">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td><td>до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="2"></td><td rowspan="3">1,25</td><td rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td rowspan="4">Твердости чугуна</td><td>Твердость чугуна НВ, ГПа</td><td colspan="4">до 2,15</td><td colspan="5">свыше 2,15</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="5" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
<tr><td colspan="4"></td></tr>
<tr><td>Группы медных</td><td>Группа сплавов</td><td colspan="4">Гомогенные</td><td colspan="5">Гетерогенные</td></tr>
<tr><td rowspan="2">сплавов и твердости</td><td>Твердость НВ, ГПа</td><td colspan="4">0,59 - 0,88</td><td colspan="2">0,98 - 1,37</td><td colspan="3">1,47 - 2,45</td></tr>
<tr><td>Коэффициент</td><td colspan="4">0,55</td><td colspan="2">1,0</td><td colspan="3">1,25</td></tr>
<tr><td>Группы алюминиевых сплавов и</td><td>Группа сплавов</td><td colspan="4">Силумин и литейные сплавы</td><td colspan="5">Дюралюминий</td></tr>
<tr><td rowspan="2">твердости</td><td>Твердость НВ, ГПа</td><td colspan="4">до 0,64</td><td colspan="5">до 0,98</td></tr>
<tr><td>Коэффициент</td><td colspan="4">0,75</td><td colspan="5">0,7</td></tr>
<tr><td rowspan="4">Состояния обрабатываемой поверхности</td><td>Состояние обрабатываемой поверхности</td><td colspan="4">без корки и удара</td><td colspan="5">по корке и на удар</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="5" rowspan="3">1,2</td></tr>
<tr><td>1,0</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="2%"><col width="1%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"></colgroup>
<tr><td colspan="24">Основное время на обработку поверхности Обработка фасок</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="24" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Резцы с пластинками Т15К6, ВК6, ВК8 и из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 109</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="6">N позиции</td><td rowspan="3">Диаметр обрабатываемой поверхности D, мм,</td><td colspan="14">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="7">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="8">Медные сплавы, НВ = 0,98 - 1,37, и алюминиевые</td></tr>
<tr><td colspan="29">Режущий инструмент</td></tr>
<tr><td colspan="7">Т15К6</td><td colspan="7">Р6М5</td><td colspan="7">ВК6, ВК8</td><td colspan="8">Р6М5</td></tr>
<tr><td rowspan="3">до</td><td colspan="4">Ширина фаски, мм, до</td><td colspan="3">Режимы резания</td><td colspan="4">Ширина фаски, мм, до</td><td colspan="3">Режимы резания</td><td colspan="4">Ширина фаски, мм, до</td><td colspan="3">Режимы резания</td><td colspan="5">Ширина фаски, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td>3</td><td>5</td><td>8</td><td>10</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">n, об./ мин.</td><td>3</td><td>5</td><td>8</td><td>10</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">n, об./ мин.</td><td>3</td><td>5</td><td>8</td><td>10</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">n, об./ мин.</td><td colspan="2">3</td><td>5</td><td>8</td><td>10</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">n, об./ мин.</td></tr>
<tr><td colspan="4">Основное время, мин.</td><td colspan="4">Основное время, мин.</td><td colspan="4">Основное время, мин.</td><td colspan="5">Основное время, мин.</td></tr>
<tr><td>1</td><td>50</td><td>0,2</td><td>0,3</td><td>0,45</td><td>0,55</td><td>19,5</td><td rowspan="7">120</td><td>750</td><td>0,28</td><td>0,43</td><td>0,65</td><td>0,78</td><td>14,0</td><td rowspan="7">40</td><td>250</td><td>0,16</td><td>0,25</td><td>0,37</td><td>0,45</td><td>24,0</td><td rowspan="7">120</td><td>600</td><td colspan="2">0,12</td><td>0,19</td><td>0,28</td><td>0,35</td><td>31,0</td><td rowspan="7">60</td><td>380</td></tr>
<tr><td>2</td><td>100</td><td>0,23</td><td>0,35</td><td>0,35</td><td>0,65</td><td>17,0</td><td>380</td><td>0,33</td><td>0,5</td><td>0,75</td><td>0,9</td><td>12,0</td><td>125</td><td>0,19</td><td>0,28</td><td>0,43</td><td>0,52</td><td>21,0</td><td>380</td><td colspan="2">0,15</td><td>0,22</td><td>0,33</td><td>0,4</td><td>27,0</td><td>190</td></tr>
<tr><td>3</td><td>200</td><td>0,33</td><td>0,5</td><td>0,75</td><td>0,9</td><td>12,0</td><td>190</td><td>0,45</td><td>0,7</td><td>1,05</td><td>1,3</td><td>8,5</td><td>63</td><td>0,28</td><td>0,43</td><td>0,65</td><td>0,78</td><td>14,0</td><td>190</td><td colspan="2">0,22</td><td>0,33</td><td>0,5</td><td>0,6</td><td>18,0</td><td>96</td></tr>
<tr><td>4</td><td>300</td><td>0,45</td><td>0,7</td><td>1,05</td><td>1,3</td><td>8,5</td><td>125</td><td>0,65</td><td>1,0</td><td>1,5</td><td>1,85</td><td>6,0</td><td>40</td><td>0,38</td><td>0,57</td><td>0,85</td><td>1,05</td><td>10,5</td><td>125</td><td colspan="2">0,3</td><td>0,45</td><td>0,65</td><td>0,8</td><td>13,5</td><td>63</td></tr>
<tr><td>5</td><td>400</td><td>0,55</td><td>0,85</td><td>1,3</td><td>1,55</td><td>7,0</td><td>96</td><td>0,8</td><td>1,2</td><td>1,8</td><td>2,2</td><td>5,0</td><td>30</td><td>0,47</td><td>0,7</td><td>1,05</td><td>1,3</td><td>8,5</td><td>90</td><td colspan="2">0,35</td><td>0,55</td><td>0,8</td><td>1,0</td><td>11,0</td><td>50</td></tr>
<tr><td>6</td><td>500</td><td>0,7</td><td>1,1</td><td>1,6</td><td>2,0</td><td>5,5</td><td>75</td><td>1,0</td><td>1,5</td><td>2,2</td><td>2,7</td><td>4,0</td><td>25</td><td>0,57</td><td>0,85</td><td>1,3</td><td>1,55</td><td>7,0</td><td>75</td><td colspan="2">0,45</td><td>0,65</td><td>1,0</td><td>1,2</td><td>9,0</td><td>38</td></tr>
<tr><td>7</td><td>600</td><td>0,8</td><td>1,2</td><td>1,8</td><td>2,2</td><td>5,0</td><td>63</td><td>1,15</td><td>1,7</td><td>2,5</td><td>3,1</td><td>3,5</td><td>21</td><td>0,7</td><td>1,1</td><td>1,6</td><td>2,0</td><td>5,5</td><td>60</td><td colspan="2">0,55</td><td>0,85</td><td>1,2</td><td>1,5</td><td>7,0</td><td>30</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="3"></td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="3"></td><td>и</td><td>к</td><td>л</td><td>м</td><td colspan="3"></td><td colspan="2">н</td><td>о</td><td>п</td><td>р</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="9%"><col width="12%"><col width="20%"><col width="5%"><col width="3%"><col width="5%"><col width="2%"><col width="7%"><col width="5%"><col width="3%"><col width="4%"><col width="4%"><col width="9%"></colgroup>
<tr><td colspan="7">Основное время на обработку поверхности Обработка фасок</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="7" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Резцы с пластинками Т15К6, ВК6, ВК8 и из стали Р6М5</td></tr>
<tr><td colspan="7">Карта 109 Лист 2</td></tr>
<tr><td colspan="14">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="9">Группы стали и предела прочности</td><td rowspan="9">Инструмент</td><td rowspan="5">Из быстрорежущей стали Р6М5</td><td>Группа стали</td><td colspan="5">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="5">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="2"></td><td rowspan="3">1,25</td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td rowspan="4">С пластинками из твердого сплава Т5К10</td><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td><td colspan="5" rowspan="4">-</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="2"></td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td colspan="2" rowspan="4">Твердости чугуна</td><td colspan="2">Твердость чугуна НВ, ГПа</td><td colspan="5">до 2,15</td><td colspan="5">свыше 2,15</td></tr>
<tr><td colspan="2" rowspan="3">Коэффициент</td><td colspan="5"></td><td colspan="5" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="4"></td></tr>
<tr><td colspan="5"></td></tr>
<tr><td colspan="2">Группы медных сплавов и</td><td colspan="2">Группа сплавов</td><td colspan="5">Гомогенные</td><td colspan="5">Гетерогенные</td></tr>
<tr><td colspan="2" rowspan="4">твердости</td><td colspan="2">Твердость НВ, ГПа</td><td colspan="5">0,59 - 0,88</td><td colspan="3">0,98 - 1,37</td><td colspan="2">1,47 - 2,45</td></tr>
<tr><td colspan="2" rowspan="3">Коэффициент</td><td colspan="5" rowspan="3">0,55</td><td colspan="3"></td><td colspan="2" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="2" rowspan="3">Группы алюминиевых сплавов и твердости</td><td colspan="2">Группа сплавов</td><td colspan="5">Силумин и литейные сплавы</td><td colspan="5">Дюралюминий</td></tr>
<tr><td colspan="2">Твердость НВ, ГПа</td><td colspan="5">до 0,64</td><td colspan="5">до 0,98</td></tr>
<tr><td colspan="2">Коэффициент</td><td colspan="5">0,75</td><td colspan="5">0,7</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="2%"><col width="1%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"><col width="3%"></colgroup>
<tr><td colspan="24">Основное время на обработку поверхности Обработка радиусов</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="24" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Резцы с пластинками Т15К6, ВК6, ВК8 и из стали Р6М5</td></tr>
<tr><td colspan="4">Карта 110</td><td colspan="3">Лист 1</td></tr>
<tr><td rowspan="6">N позиции</td><td rowspan="3">Диаметр обрабатываемой поверхности D, мм,</td><td colspan="14">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="7">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="8">Медные сплавы, НВ = 0,98 - 1,37, и алюминиевые</td></tr>
<tr><td colspan="29">Режущий инструмент</td></tr>
<tr><td colspan="7">Т15К6</td><td colspan="7">Р6М5</td><td colspan="7">ВК6, ВК8</td><td colspan="8">Р6М5</td></tr>
<tr><td rowspan="3">до</td><td colspan="4">Размер радиуса, мм, до</td><td colspan="3">Режимы резания</td><td colspan="4">Размер радиуса, мм, до</td><td colspan="3">Режимы резания</td><td colspan="4">Размер радиуса, мм, до</td><td colspan="3">Режимы резания</td><td colspan="5">Размер радиуса, мм, до</td><td colspan="3">Режимы резания</td></tr>
<tr><td>3</td><td>5</td><td>8</td><td>10</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">n, об./ мин.</td><td>3</td><td>5</td><td>8</td><td>10</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">n, об./ мин.</td><td>3</td><td>5</td><td>8</td><td>10</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">n, об./ мин.</td><td colspan="2">3</td><td>5</td><td>8</td><td>10</td><td rowspan="2">S , м мм/ мин.</td><td rowspan="2">v, м/ мин.</td><td rowspan="2">n, об./ мин.</td></tr>
<tr><td colspan="4">Основное время, мин.</td><td colspan="4">Основное время, мин.</td><td colspan="4">Основное время, мин.</td><td colspan="5">Основное время, мин.</td></tr>
<tr><td>1</td><td>50</td><td>0,26</td><td>0,38</td><td>0,6</td><td>0,7</td><td>15,0</td><td rowspan="7">120</td><td>750</td><td>0,35</td><td>0,55</td><td>0,8</td><td>1,0</td><td>11,0</td><td rowspan="7">40</td><td>250</td><td>0,22</td><td>0,33</td><td>0,5</td><td>0,6</td><td>18,0</td><td rowspan="7">115</td><td>600</td><td colspan="2">0,17</td><td>0,25</td><td>0,38</td><td>0,45</td><td>23,0</td><td rowspan="7">60</td><td>380</td></tr>
<tr><td>2</td><td>100</td><td>0,33</td><td>0,5</td><td>0,75</td><td>0,9</td><td>12,0</td><td>380</td><td>0,45</td><td>0,7</td><td>1,05</td><td>1,3</td><td>8,5</td><td>125</td><td>0,28</td><td>0,43</td><td>0,65</td><td>0,75</td><td>14,0</td><td>380</td><td colspan="2">0,21</td><td>0,33</td><td>0,5</td><td>0,6</td><td>18,0</td><td>190</td></tr>
<tr><td>3</td><td>200</td><td>0,45</td><td>0,7</td><td>1,05</td><td>1,3</td><td>8,5</td><td>190</td><td>0,65</td><td>1,0</td><td>1,5</td><td>1,8</td><td>6,0</td><td>63</td><td>0,4</td><td>0,6</td><td>0,9</td><td>1,1</td><td>10,0</td><td>190</td><td colspan="2">0,31</td><td>0,45</td><td>0,7</td><td>0,85</td><td>13,0</td><td>96</td></tr>
<tr><td>4</td><td>300</td><td>0,65</td><td>1,0</td><td>1,5</td><td>1,8</td><td>6,0</td><td>125</td><td>0,95</td><td>1,4</td><td>2,15</td><td>2,6</td><td>4,2</td><td>40</td><td>0,5</td><td>0,75</td><td>1,1</td><td>1,35</td><td>8,0</td><td>125</td><td colspan="2">0,4</td><td>0,6</td><td>0,85</td><td>1,05</td><td>10,5</td><td>63</td></tr>
<tr><td>5</td><td>400</td><td>0,8</td><td>1,2</td><td>1,8</td><td>2,2</td><td>5,0</td><td>96</td><td>1,15</td><td>1,7</td><td>2,5</td><td>3,1</td><td>3,5</td><td>30</td><td>0,65</td><td>1,0</td><td>1,5</td><td>1,8</td><td>6,0</td><td>90</td><td colspan="2">0,5</td><td>0,75</td><td>1,15</td><td>1,4</td><td>8,0</td><td>50</td></tr>
<tr><td>6</td><td>500</td><td>1,0</td><td>1,5</td><td>2,2</td><td>2,7</td><td>4,0</td><td>75</td><td>1,4</td><td>2,1</td><td>3,2</td><td>3,9</td><td>2,8</td><td>25</td><td>0,8</td><td>1,2</td><td>1,8</td><td>2,2</td><td>5,0</td><td>75</td><td colspan="2">0,66</td><td>0,9</td><td>1,4</td><td>1,7</td><td>6,5</td><td>38</td></tr>
<tr><td>7</td><td>600</td><td>1,4</td><td>2,1</td><td>3,2</td><td>3,9</td><td>2,8</td><td>63</td><td>2,0</td><td>3,0</td><td>4,5</td><td>5,5</td><td>2,0</td><td>21</td><td>1,0</td><td>1,4</td><td>2,1</td><td>2,6</td><td>4,2</td><td>63</td><td colspan="2">0,75</td><td>1,1</td><td>1,6</td><td>2,0</td><td>5,5</td><td>30</td></tr>
<tr><td colspan="2">Индекс</td><td>а</td><td>б</td><td>в</td><td>г</td><td colspan="3"></td><td>д</td><td>е</td><td>ж</td><td>з</td><td colspan="3"></td><td>и</td><td>к</td><td>л</td><td>м</td><td colspan="3"></td><td colspan="2">н</td><td>о</td><td>п</td><td>р</td><td colspan="3"></td></tr>
</table>



<table>
<colgroup><col width="11%"><col width="9%"><col width="12%"><col width="20%"><col width="5%"><col width="3%"><col width="5%"><col width="2%"><col width="7%"><col width="5%"><col width="3%"><col width="4%"><col width="4%"><col width="9%"></colgroup>
<tr><td colspan="7">Основное время на обработку поверхности Обработка радиусов</td><td colspan="7">Горизонтально-расточные станки</td></tr>
<tr><td colspan="7" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="7">Резцы с пластинками Т15К6, ВК6, ВК8 и из стали Р6М5</td></tr>
<tr><td colspan="7">Карта 110 Лист 2</td></tr>
<tr><td colspan="14">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="9">Группы стали и предела прочности</td><td rowspan="9">Инструмент</td><td rowspan="5">Из быстрорежущей стали Р6М5</td><td>Группа стали</td><td colspan="5">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="5">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="2"></td><td rowspan="3">1,25</td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td rowspan="4">С пластинками из твердого сплава Т15К6</td><td>Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td><td colspan="5" rowspan="4">-</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="2"></td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td></td></tr>
<tr><td colspan="2"></td></tr>
<tr><td colspan="2" rowspan="4">Твердости чугуна</td><td colspan="2">Твердость чугуна НВ, ГПа</td><td colspan="5">до 2,15</td><td colspan="5">свыше 2,15</td></tr>
<tr><td colspan="2" rowspan="3">Коэффициент</td><td colspan="5"></td><td colspan="5" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="4"></td></tr>
<tr><td colspan="5"></td></tr>
<tr><td colspan="2">Группы медных сплавов и</td><td colspan="2">Группа сплавов</td><td colspan="5">Гомогенные</td><td colspan="5">Гетерогенные</td></tr>
<tr><td colspan="2" rowspan="4">твердости</td><td colspan="2">Твердость НВ, ГПа</td><td colspan="5">0,59 - 0,88</td><td colspan="3">0,98 - 1,37</td><td colspan="2">1,47 - 2,45</td></tr>
<tr><td colspan="2" rowspan="3">Коэффициент</td><td colspan="5" rowspan="3">0,55</td><td colspan="3"></td><td colspan="2" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="2" rowspan="3">Группы алюминиевых сплавов и твердости</td><td colspan="2">Группа сплавов</td><td colspan="5">Силумин и литейные сплавы</td><td colspan="5">Дюралюминий</td></tr>
<tr><td colspan="2">Твердость НВ, ГПа</td><td colspan="5">до 0,64</td><td colspan="5">до 0,98</td></tr>
<tr><td colspan="2">Коэффициент</td><td colspan="5">0,75</td><td colspan="5">0,7</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="5%"><col width="4%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="4%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"></colgroup>
<tr><td colspan="17">Основное время на 100 мм расчетной длины Фрезерование плоскостей, Rz 80, 1Т14 - 1Т12 квалитет, Rz 40 - Rz 20, 1Т11 квалитет, Ra 2,5, 1Т9 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="17" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Среднесерийное производство</td><td colspan="5">Фрезы торцовые с пластинками ВК, ВК6</td></tr>
<tr><td colspan="5">Карта 111 Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность станка</td><td>Диаметр фрезы D, мм,</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td colspan="6">Фрезерование плоскостей, Rz 80 Фрезы с пластинками ВК8</td><td colspan="6">Фрезерование плоскостей, Rz 40 - Rz 20 Фрезы с пластинками ВК8</td><td colspan="6">Фрезерование плоскостей, Ra 2,5 Фрезы с пластинками ВК6</td></tr>
<tr><td rowspan="2">N , д кВт, до</td><td rowspan="2">и число зубьев z</td><td rowspan="2">Глубина резания t, мм, до</td><td rowspan="2">Величина врезания и перебега, l , 1 l , мм 2</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">Глубина резания t, мм, до</td><td rowspan="2">Величина врезания и перебега, l , 1 l , мм 2</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">Глубина резания t, мм, до</td><td rowspan="2">Величина врезания и перебега, l , 1 l , мм 2</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td>n, об./ мин.</td><td>S , м мм/ мин.</td><td>v, м/ мин.</td><td>n, об./ мин.</td><td>S , м мм/ мин.</td><td>v, м/ мин.</td><td>n, об./ мин.</td><td>S , м мм/ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>1</td><td rowspan="18">7,5 - 10</td><td rowspan="2">20 -- 10</td><td rowspan="2">48</td><td>3</td><td rowspan="2">10</td><td>380</td><td>600</td><td>95</td><td>0,167</td><td>3</td><td rowspan="2">80</td><td>480</td><td>600</td><td>120</td><td>0,167</td><td rowspan="18">1</td><td rowspan="2">80</td><td rowspan="2">750</td><td rowspan="2">750</td><td rowspan="2">188</td><td rowspan="2">0,104</td></tr>
<tr><td>2</td><td>5</td><td>300</td><td>480</td><td>75</td><td>0,208</td><td>5</td><td>380</td><td>480</td><td>95</td><td>0,208</td></tr>
<tr><td>3</td><td rowspan="2">100 --- 10</td><td rowspan="2">60</td><td>3</td><td rowspan="2">13</td><td>300</td><td>480</td><td>94</td><td>0,208</td><td>3</td><td rowspan="2">100</td><td>380</td><td>480</td><td>120</td><td>0,208</td><td rowspan="2">100</td><td rowspan="2">600</td><td rowspan="2">600</td><td rowspan="2">188</td><td rowspan="2">0,133</td></tr>
<tr><td>4</td><td>5</td><td>240</td><td>380</td><td>75</td><td>0,263</td><td>5</td><td>300</td><td>380</td><td>95</td><td>0,263</td></tr>
<tr><td>5</td><td rowspan="2">125 --- 12</td><td rowspan="2">75</td><td>3</td><td rowspan="2">16</td><td>240</td><td>480</td><td>94</td><td>0,208</td><td>3</td><td rowspan="2">125</td><td>300</td><td>380</td><td>120</td><td>0,263</td><td rowspan="2">125</td><td rowspan="2">480</td><td rowspan="2">480</td><td rowspan="2">188</td><td rowspan="2">0,167</td></tr>
<tr><td>6</td><td>5</td><td>190</td><td>380</td><td>75</td><td>0,263</td><td>5</td><td>240</td><td>300</td><td>95</td><td>0,333</td></tr>
<tr><td>7</td><td rowspan="3">160 --- 16</td><td rowspan="3">112</td><td>3</td><td rowspan="3">26</td><td>150</td><td>380</td><td>75</td><td>0,263</td><td>3</td><td rowspan="3">160</td><td>240</td><td>380</td><td>120</td><td>0,263</td><td rowspan="3">160</td><td rowspan="3">380</td><td rowspan="3">480</td><td rowspan="3">190</td><td rowspan="3">0,167</td></tr>
<tr><td>8</td><td>5</td><td>120</td><td>300</td><td>60</td><td>0,333</td><td>5</td><td>190</td><td>300</td><td>95</td><td>0,333</td></tr>
<tr><td>9</td><td>8</td><td>96</td><td>190</td><td>48</td><td>0,53</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td rowspan="3">200 --- 20</td><td rowspan="3">140</td><td>3</td><td rowspan="3">33</td><td>96</td><td>300</td><td>60</td><td>0,333</td><td>3</td><td rowspan="3">200</td><td>190</td><td>380</td><td>120</td><td>0,263</td><td rowspan="3">200</td><td rowspan="3">300</td><td rowspan="3">480</td><td rowspan="3">188</td><td rowspan="3">0,167</td></tr>
<tr><td>11</td><td>5</td><td>75</td><td>240</td><td>47</td><td>0,417</td><td>5</td><td>150</td><td>300</td><td>94</td><td>0,333</td></tr>
<tr><td>12</td><td>8</td><td>60</td><td>150</td><td>38</td><td>0,67</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td rowspan="3">250 --- 24</td><td rowspan="3">190</td><td>3</td><td rowspan="3">49</td><td>75</td><td>300</td><td>59</td><td>0,333</td><td>3</td><td rowspan="3">250</td><td>150</td><td>300</td><td>118</td><td>0,333</td><td rowspan="3">250</td><td rowspan="3">240</td><td rowspan="3">480</td><td rowspan="3">188</td><td rowspan="3">0,167</td></tr>
<tr><td>14</td><td>5</td><td>60</td><td>240</td><td>47</td><td>0,417</td><td>5</td><td>120</td><td>190</td><td>94</td><td>0,53</td></tr>
<tr><td>15</td><td>8</td><td>48</td><td>120</td><td>38</td><td>0,83</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td rowspan="3">315 --- 24</td><td rowspan="3">240</td><td>3</td><td rowspan="3">60</td><td>60</td><td>240</td><td>59,5</td><td>0,417</td><td>3</td><td rowspan="3">315</td><td>120</td><td>240</td><td>119</td><td>0,417</td><td rowspan="3">315</td><td rowspan="3">190</td><td rowspan="3">380</td><td rowspan="3">188</td><td rowspan="3">0,208</td></tr>
<tr><td>17</td><td>5</td><td>48</td><td>190</td><td>47,5</td><td>0,53</td><td>5</td><td>96</td><td>150</td><td>95</td><td>0,67</td></tr>
<tr><td>18</td><td>8</td><td>38</td><td>96</td><td>37,5</td><td>1,04</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="9">Индекс</td><td>а</td><td colspan="5"></td><td>б</td><td colspan="5"></td><td>в</td></tr>
</table>



<table>
<colgroup><col width="27%"><col width="27%"><col width="3%"><col width="4%"><col width="16%"><col width="3%"><col width="20%"></colgroup>
<tr><td colspan="3" rowspan="2">Основное время на 100 мм расчетной длины Фрезерование плоскостей, Rz 80, 1Т14 - 1Т12 квалитет, Rz 40 - Rz 20, 1Т11 квалитет, Ra 2,5, 1Т9 квалитет Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="4">Горизонтально-расточные станки</td></tr>
<tr><td colspan="4">Фрезы торцовые с пластинками ВК8, ВК6</td></tr>
<tr><td colspan="3">Среднесерийное производство</td><td colspan="3">Карта 111</td><td>Лист 2</td></tr>
<tr><td colspan="7">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="4">Твердости чугуна</td><td>Твердость НВ, ГПа</td><td colspan="3">до 2,15</td><td colspan="2">свыше 2,15</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="3"></td><td colspan="2" rowspan="3">1,25</td></tr>
<tr><td colspan="2">1,0</td><td></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td rowspan="4">Состояния обрабатываемой поверхности</td><td>Состояние обрабатываемой поверхности</td><td colspan="3">без корки</td><td colspan="2">по корке</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="3"></td><td colspan="2" rowspan="3">1,2</td></tr>
<tr><td colspan="2">1,0</td><td></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="5%"><col width="4%"><col width="6%"><col width="1%"><col width="2%"><col width="4%"><col width="4%"><col width="6%"><col width="6%"><col width="4%"><col width="2%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="6%"><col width="4%"><col width="6%"><col width="4%"><col width="4%"><col width="1%"><col width="2%"><col width="6%"></colgroup>
<tr><td colspan="26">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Фрезерование плоскостей, Rz 80, 1Т14 - 1Т12 квалитет, Rz 40 - Rz 20, 1Т11 квалитет, Ra 2,5, 1Т9 квалитет</td></tr>
<tr><td colspan="26">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа Фрезы торцовые из стали Р6М5 в</td></tr>
<tr><td colspan="26">Среднесерийное производство Карта 112</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность</td><td>Диаметр фрезы</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td colspan="7">Фрезерование плоскостей, Rz 80</td><td colspan="8">Фрезерование плоскостей, Rz 40 - Rz 20</td><td colspan="7">Фрезерование плоскостей, Ra 2,5</td></tr>
<tr><td rowspan="2">станка N , д кВт, до</td><td rowspan="2">D, мм, и число зубьев z</td><td rowspan="2">Глубина резания t, мм, до</td><td rowspan="2">Величина врезания и перебега, l , 1 l , мм 2</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">Глубина резания t, мм, до</td><td colspan="2" rowspan="2">Величина врезания и перебега, l , 1 l , мм 2</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">Глубина резания t, мм, до</td><td rowspan="2">Величина врезания и перебега, l , 1 l , мм 2</td><td colspan="4">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td colspan="2">S , м мм/ мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/ мин.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td><td>S , м мм/ мин.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td>1</td><td rowspan="12">7,5 - 10</td><td rowspan="2">80 -- 10</td><td rowspan="2">48</td><td>3</td><td rowspan="2">10</td><td colspan="2">120</td><td>75</td><td>19</td><td>0,83</td><td>3</td><td colspan="2" rowspan="2">80</td><td>150</td><td>120</td><td colspan="2">30,0</td><td>0,67</td><td rowspan="12">1</td><td rowspan="2">80</td><td rowspan="2">60</td><td rowspan="2">150</td><td colspan="2" rowspan="2">37,5</td><td rowspan="2">1,67</td></tr>
<tr><td>2</td><td>5</td><td colspan="2">90</td><td>75</td><td>19</td><td>1,04</td><td>5</td><td>120</td><td>120</td><td colspan="2">30,0</td><td>0,83</td></tr>
<tr><td>3</td><td rowspan="2">100 --- 10</td><td rowspan="2">60</td><td>3</td><td rowspan="2">13</td><td colspan="2">96</td><td>60</td><td>19</td><td>1,04</td><td>3</td><td colspan="2" rowspan="2">100</td><td>120</td><td>96</td><td colspan="2">30,0</td><td>0,83</td><td rowspan="2">100</td><td rowspan="2">48</td><td rowspan="2">120</td><td colspan="2" rowspan="2">38,0</td><td rowspan="2">2,08</td></tr>
<tr><td>4</td><td>5</td><td colspan="2">75</td><td>60</td><td>19</td><td>1,33</td><td>5</td><td>96</td><td>96</td><td colspan="2">30,0</td><td>1,04</td></tr>
<tr><td>5</td><td rowspan="2">125 --- 14</td><td rowspan="2">75</td><td>3</td><td rowspan="2">16</td><td colspan="2">96</td><td>48</td><td>19</td><td>1,04</td><td>3</td><td colspan="2" rowspan="2">125</td><td>120</td><td>60</td><td colspan="2">23,5</td><td>0,83</td><td rowspan="2">125</td><td rowspan="2">38</td><td rowspan="2">96</td><td colspan="2" rowspan="2">38,0</td><td rowspan="2">2,63</td></tr>
<tr><td>6</td><td>5</td><td colspan="2">75</td><td>48</td><td>19</td><td>1,33</td><td>5</td><td>96</td><td>60</td><td colspan="2">23,5</td><td>1,04</td></tr>
<tr><td>7</td><td rowspan="3">160 --- 16</td><td rowspan="3">112</td><td>3</td><td rowspan="3">26</td><td colspan="2">96</td><td>38</td><td>19</td><td>1,04</td><td>3</td><td colspan="2" rowspan="3">160</td><td>120</td><td>48</td><td colspan="2">24,0</td><td>0,83</td><td rowspan="3">160</td><td rowspan="3">30</td><td rowspan="3">75</td><td colspan="2" rowspan="3">38,0</td><td rowspan="3">3,33</td></tr>
<tr><td>8</td><td>5</td><td colspan="2">75</td><td>38</td><td>19</td><td>1,33</td><td>5</td><td>96</td><td>48</td><td colspan="2">24,0</td><td>1,04</td></tr>
<tr><td>9</td><td>8</td><td colspan="2">60</td><td>38</td><td>19</td><td>1,67</td><td></td><td></td><td></td><td colspan="2"></td><td></td></tr>
<tr><td>10</td><td rowspan="3">200 --- 20</td><td rowspan="3">140</td><td>3</td><td rowspan="3">33</td><td colspan="2">96</td><td>30</td><td>19</td><td>1,04</td><td>3</td><td colspan="2" rowspan="3">200</td><td>96</td><td>38</td><td colspan="2">24,0</td><td>1,04</td><td rowspan="3">200</td><td rowspan="3">24</td><td rowspan="3">60</td><td colspan="2" rowspan="3">38,0</td><td rowspan="3">4,17</td></tr>
<tr><td>11</td><td>5</td><td colspan="2">75</td><td>30</td><td>19</td><td>1,33</td><td>5</td><td>75</td><td>38</td><td colspan="2">24,0</td><td>1,33</td></tr>
<tr><td>12</td><td>8</td><td colspan="2">60</td><td>30</td><td>19</td><td>1,67</td><td></td><td></td><td></td><td colspan="2"></td><td></td></tr>
<tr><td colspan="10">Индекс</td><td>а</td><td colspan="7"></td><td>б</td><td colspan="6"></td><td>в</td></tr>
<tr><td colspan="26">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="7" rowspan="5">Группы стали и предела прочности</td><td colspan="5">Группа стали</td><td colspan="7">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="7">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="5">Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="2">свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="3"></td><td colspan="2" rowspan="3">1,25</td><td colspan="2" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,2</td><td colspan="2" rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="7" rowspan="5">Состояния обрабатываемой поверхности</td><td colspan="5" rowspan="2">Вид обрабатываемой поверхности</td><td colspan="9">По корке</td><td colspan="5" rowspan="2">Без корки</td></tr>
<tr><td colspan="5">отливка</td><td colspan="4">поковка</td></tr>
<tr><td colspan="5" rowspan="3">Коэффициент</td><td colspan="5"></td><td colspan="4" rowspan="3">0,9</td><td colspan="5" rowspan="3">0,8</td></tr>
<tr><td>1,0</td><td colspan="4"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="5%"><col width="6%"><col width="5%"><col width="4%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="6%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"><col width="4%"><col width="6%"><col width="4%"><col width="4%"><col width="4%"><col width="6%"></colgroup>
<tr><td colspan="17">Основное время на 100 мм расчетной длины Фрезерование плоскостей, Rz 80, 1Т14 - 1Т12 квалитет, Rz 40 - Rz 20, 1Т11 квалитет, Ra 2,5, 1Т9 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="17" rowspan="2">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Среднесерийное производство</td><td colspan="5">Фрезы торцовые с пластинками Т5К10, Т15К6</td></tr>
<tr><td colspan="5">Карта 113 Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность станка</td><td>Диаметр фрезы D, мм,</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td colspan="6">Фрезерование плоскостей, Rz 80 Фрезы с пластинками Т5К10</td><td colspan="6">Фрезерование плоскостей, Rz 40 - Rz 20 Фрезы с пластинками Т5К10</td><td colspan="6">Фрезерование плоскостей, Ra 2,5 Фрезы с пластинками Т15К6</td></tr>
<tr><td rowspan="2">N , д кВт, до</td><td rowspan="2">и число зубьев z</td><td rowspan="2">Глубина резания t, мм, до</td><td rowspan="2">Величина врезания и перебега, l , 1 l , мм 2</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">Глубина резания t, мм, до</td><td rowspan="2">Величина врезания и перебега, l , 1 l , мм 2</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td rowspan="2">Глубина резания t, мм, до</td><td rowspan="2">Величина врезания и перебега, l , 1 l , мм 2</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td>S , м мм/ мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/ мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/ мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>1</td><td rowspan="18">7,5 - 10</td><td rowspan="2">80 -- 8</td><td rowspan="2">48</td><td>3</td><td rowspan="2">10</td><td>480</td><td>480</td><td>120</td><td>0,208</td><td>3</td><td rowspan="2">80</td><td>380</td><td>600</td><td>150</td><td>0,263</td><td rowspan="18">1</td><td rowspan="2">80</td><td rowspan="2">300</td><td rowspan="2">750</td><td rowspan="2">188</td><td rowspan="2">0,333</td></tr>
<tr><td>2</td><td>5</td><td>380</td><td>380</td><td>96,0</td><td>0,263</td><td>5</td><td>300</td><td>480</td><td>120</td><td>0,333</td></tr>
<tr><td>3</td><td rowspan="2">100 --- 8</td><td rowspan="2">60</td><td>3</td><td rowspan="2">13</td><td>380</td><td>380</td><td>120</td><td>0,263</td><td>3</td><td rowspan="2">100</td><td>300</td><td>480</td><td>150</td><td>0,333</td><td rowspan="2">100</td><td rowspan="2">240</td><td rowspan="2">600</td><td rowspan="2">188</td><td rowspan="2">0,417</td></tr>
<tr><td>4</td><td>5</td><td>300</td><td>300</td><td>96,0</td><td>0,333</td><td>5</td><td>240</td><td>380</td><td>120</td><td>0,417</td></tr>
<tr><td>5</td><td rowspan="2">125 --- 8</td><td rowspan="2">75</td><td>3</td><td rowspan="2">16</td><td>300</td><td>300</td><td>118</td><td>0,333</td><td>3</td><td rowspan="2">125</td><td>300</td><td>380</td><td>149</td><td>0,333</td><td rowspan="2">125</td><td rowspan="2">190</td><td rowspan="2">480</td><td rowspan="2">188</td><td rowspan="2">0,530</td></tr>
<tr><td>6</td><td>5</td><td>240</td><td>240</td><td>94,0</td><td>0,417</td><td>5</td><td>240</td><td>300</td><td>118</td><td>0,417</td></tr>
<tr><td>7</td><td rowspan="3">160 --- 10</td><td rowspan="3">112</td><td>3</td><td rowspan="2">26</td><td>240</td><td>190</td><td>94,0</td><td>0,417</td><td>3</td><td rowspan="2">160</td><td>240</td><td>300</td><td>150</td><td>0,417</td><td rowspan="2">160</td><td rowspan="2">150</td><td rowspan="2">380</td><td rowspan="2">190</td><td rowspan="2">0,670</td></tr>
<tr><td>8</td><td>5</td><td>150</td><td>120</td><td>60,0</td><td>0,670</td><td>5</td><td>150</td><td>240</td><td>120</td><td>0,670</td></tr>
<tr><td>9</td><td>8</td><td></td><td>96</td><td>75</td><td>38,0</td><td>1,040</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10</td><td rowspan="3">200 --- 12</td><td rowspan="3">140</td><td>3</td><td rowspan="3">33</td><td>190</td><td>120</td><td>75,0</td><td>0,530</td><td>3</td><td rowspan="3">200</td><td>190</td><td>240</td><td>150</td><td>0,530</td><td rowspan="3">200</td><td rowspan="3">150</td><td rowspan="3">300</td><td rowspan="3">188</td><td rowspan="3">0,670</td></tr>
<tr><td>11</td><td>5</td><td>120</td><td>75</td><td>47,0</td><td>0,830</td><td>5</td><td>120</td><td>190</td><td>120</td><td>0,830</td></tr>
<tr><td>12</td><td>8</td><td>96</td><td>60</td><td>38,0</td><td>1,040</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>13</td><td rowspan="3">250 --- 14</td><td rowspan="3">190</td><td>3</td><td rowspan="3">49</td><td>150</td><td>75</td><td>59,0</td><td>0,670</td><td>3</td><td rowspan="3">250</td><td>150</td><td>190</td><td>149</td><td>0,670</td><td rowspan="3">250</td><td rowspan="3">120</td><td rowspan="3">240</td><td rowspan="3">188</td><td rowspan="3">0,830</td></tr>
<tr><td>14</td><td>5</td><td>96</td><td>60</td><td>47,0</td><td>1,040</td><td>5</td><td>96</td><td>150</td><td>118</td><td>1,040</td></tr>
<tr><td>15</td><td>8</td><td>75</td><td>48</td><td>37,5</td><td>1,330</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>16</td><td rowspan="3">320 --- 18</td><td rowspan="3">240</td><td>3</td><td rowspan="3">60</td><td>150</td><td>75</td><td>74,0</td><td>0,670</td><td>3</td><td rowspan="3">320</td><td>150</td><td>150</td><td>150</td><td>0,670</td><td rowspan="3">320</td><td rowspan="3">120</td><td rowspan="3">190</td><td rowspan="3">190</td><td rowspan="3">0,830</td></tr>
<tr><td>17</td><td>5</td><td>96</td><td>48</td><td>47,5</td><td>1,040</td><td>5</td><td>96</td><td>120</td><td>120</td><td>1,040</td></tr>
<tr><td>18</td><td>8</td><td>60</td><td>30</td><td>30,0</td><td>1,670</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="9">Индекс</td><td>а</td><td colspan="5"></td><td>б</td><td colspan="5"></td><td>в</td></tr>
</table>



<table>
<colgroup><col width="27%"><col width="27%"><col width="4%"><col width="3%"><col width="8%"><col width="7%"><col width="5%"><col width="4%"><col width="15%"></colgroup>
<tr><td colspan="3" rowspan="2">Основное время на 100 мм расчетной длины Фрезерование плоскостей, Rz 80, 1Т14 - 1Т12 квалитет, Rz 40 - Rz 20, 1Т11 квалитет, Ra 2,5, 1Т9 квалитет Сталь конструкционная углеродистая,</td><td colspan="6">Горизонтально-расточные станки</td></tr>
<tr><td colspan="6">Фрезы торцовые с пластинками Т5К10, Т15К6</td></tr>
<tr><td colspan="3">сигма = 0,59 - 0,74 ГПа в Среднесерийное производство</td><td colspan="4">Карта 113</td><td colspan="2">Лист 2</td></tr>
<tr><td colspan="9">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td rowspan="4">Предела прочности стали</td><td>Предел прочности сигма , ГПа в</td><td colspan="3">до 0,59</td><td colspan="3">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="3" rowspan="3">0,8</td><td colspan="3"></td><td rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td rowspan="5">Состояния обрабатываемой поверхности</td><td rowspan="2">Состояние обрабатываемой поверхности</td><td colspan="6">По корке</td><td rowspan="2">Без корки</td></tr>
<tr><td colspan="3">отливка</td><td colspan="3">поковка</td></tr>
<tr><td rowspan="3">Коэффициент</td><td colspan="3"></td><td colspan="3" rowspan="3">0,9</td><td rowspan="3">0,8</td></tr>
<tr><td colspan="2">1,0</td><td></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="13">Основное время на 100 мм расчетной длины Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Сталь конструкционная углеродистая, чугун серый, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="5">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 114</td><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность станка N , д</td><td>Диаметр фрезы D, мм, и число зубьев</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , l ,</td><td colspan="4">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="4">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="4">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="2">кВт, до</td><td rowspan="2">z</td><td rowspan="2">1 2 мм</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>1</td><td rowspan="8">7,5 - 10</td><td>16 -- 4</td><td>20 - 30</td><td>3</td><td>8</td><td>150</td><td>750</td><td>37,5</td><td>0,67</td><td>240</td><td>750</td><td>37,5</td><td>0,42</td><td>380</td><td>1200</td><td>60</td><td>0,26</td></tr>
<tr><td>2</td><td rowspan="2">20 -- 5</td><td>20 - 40</td><td>3</td><td>8</td><td>240</td><td>600</td><td>37,5</td><td>0,42</td><td>300</td><td>480</td><td>30,0</td><td>0,33</td><td>600</td><td>960</td><td>60</td><td>0,17</td></tr>
<tr><td>3</td><td>-</td><td>5</td><td>10</td><td>150</td><td>480</td><td>30,0</td><td>0,67</td><td>190</td><td>380</td><td>24,0</td><td>0,53</td><td>380</td><td>750</td><td>47</td><td>0,26</td></tr>
<tr><td>4</td><td rowspan="2">25 -- 5</td><td rowspan="2">20 - 40</td><td>3</td><td>10</td><td>190</td><td>480</td><td>37,5</td><td>0,53</td><td>300</td><td>480</td><td>37,5</td><td>0,33</td><td>480</td><td>750</td><td>59</td><td>0,21</td></tr>
<tr><td>5</td><td>5</td><td>12</td><td>120</td><td>380</td><td>30,0</td><td>0,83</td><td>190</td><td>380</td><td>30,0</td><td>0,53</td><td>380</td><td>750</td><td>59</td><td>0,26</td></tr>
<tr><td>6</td><td rowspan="3">28 -- 5</td><td rowspan="3">20 - 50</td><td>3</td><td>10</td><td>190</td><td>380</td><td>33,5</td><td>0,53</td><td>300</td><td>380</td><td>33,5</td><td>0,33</td><td>480</td><td>600</td><td>53</td><td>0,21</td></tr>
<tr><td>7</td><td>5</td><td>12</td><td>120</td><td>300</td><td>26,0</td><td>0,83</td><td>190</td><td>300</td><td>26,5</td><td>0,53</td><td>300</td><td>480</td><td>42</td><td>0,33</td></tr>
<tr><td>8</td><td>8</td><td>15</td><td>75</td><td>300</td><td>26,0</td><td>1,33</td><td>120</td><td>240</td><td>21,0</td><td>0,83</td><td>240</td><td>480</td><td>42</td><td>0,42</td></tr>
<tr><td colspan="9">Индекс</td><td>а</td><td colspan="3"></td><td>б</td><td colspan="3"></td><td>в</td></tr>
</table>



```text
┌───────────────────────────────────────────────────────────────────────────────────────┬──────────────────────────────┐
│Основное время на 100 мм расчетной длины                                               │Горизонтально-расточные станки│
│Фрезерование плоскостей, Rz 40 - Rz 20, 1Т11 квалитет                                  ├──────────────────────────────┤
│Сталь конструкционная углеродистая, чугун серый, медные сплавы и алюминиевые           │ Фрезы концевые из стали Р6М5 │
│Среднесерийное производство                                                            ├────────────────────┬─────────┤
│                                                                                       │     Карта 114      │ Лист 2  │
├───────────────────────────────────────────────────────────────────────────────────────┴────────────────────┴─────────┤
│             Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:              │
├──────────────────────────┬─────────────────┬────────────────────────────────────┬────────────────────────────────────┤
│Группы обрабатываемой     │Группа стали     │Углеродистые, хромистые, никелевые, │Марганцовистые, хромомарганцовистые,│
│стали и предела прочности │                 │           хромоникелевые           │ хромомолибденовые и близкие к ним  │
│                          ├─────────────────┼─────────┬─────────────┬────────────┼──────────┬────────────┬────────────┤
│                          │Предел прочности │до 0,59  │0,59 - 0,74  │свыше 0,74  │до 0,59   │0,59 - 0,74 │свыше 0,74  │
│                          │сигма , ГПа      │         │             │            │          │            │            │
│                          │     в           │         │             │            │          │            │            │
│                          ├─────────────────┼─────────┼─────────────┼────────────┼──────────┼────────────┼────────────┤
│                          │                 │         │┌───┐        │            │          │            │            │
│                          │Коэффициент      │0,8      ││1,0│        │1,25        │1,1       │1,2         │1,35        │
│                          │                 │         │└───┘        │            │          │            │            │
├──────────────────────────┼─────────────────┼─────────┴─────────────┴────────────┼──────────┴────────────┴────────────┤
│Твердости чугуна          │Твердость НВ, ГПа│до 2,15                             │свыше 2,15                          │
│                          ├─────────────────┼────────────────────────────────────┼────────────────────────────────────┤
│                          │                 │┌───┐                               │                                    │
│                          │Коэффициент      ││1,0│                               │1,25                                │
│                          │                 │└───┘                               │                                    │
├──────────────────────────┼─────────────────┼────────────────────────────────────┼────────────────────────────────────┤
│Группы медных сплавов     │Группа сплавов   │             Гомогенные             │Гетерогенные                        │
│и твердости               ├─────────────────┼──────────────────┬─────────────────┼────────────────────────────────────┤
│                          │Твердость НВ, ГПа│0,59 - 0,74       │0,98 - 1,37      │1,47 - 2,15                         │
│                          ├─────────────────┼──────────────────┼─────────────────┼────────────────────────────────────┤
│                          │                 │                  │┌───┐            │                                    │
│                          │Коэффициент      │0,55              ││1,0│            │1,25                                │
│                          │                 │                  │└───┘            │                                    │
├──────────────────────────┼─────────────────┼──────────────────┴─────────────────┼────────────────────────────────────┤
│Группы алюминиевых сплавов│Группа сплавов   │Силумин и литейные сплавы           │Дюралюминий                         │
│и твердости               ├─────────────────┼────────────────────────────────────┼────────────────────────────────────┤
│                          │Твердость НВ, ГПа│до 0,64                             │до 0,98                             │
│                          ├─────────────────┼────────────────────────────────────┼────────────────────────────────────┤
│                          │Коэффициент      │0,75                                │0,7                                 │
└──────────────────────────┴─────────────────┴────────────────────────────────────┴────────────────────────────────────┘
```



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="8%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="4%"><col width="5%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="12">Основное время на 100 мм расчетной длины Фрезерование пазов, Rz 40 - Rz 20</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="12" rowspan="2">Сталь конструкционная углеродистая, чугун серый, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="5">Фрезы концевые из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 115</td><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность станка N , д</td><td>Диаметр фрезы D, мм, и число зубьев</td><td rowspan="3">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , l ,</td><td colspan="4">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="4">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="4">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="2">кВт, до</td><td rowspan="2">z</td><td rowspan="2">1 2 мм</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>1</td><td rowspan="8">7,5 - 10</td><td rowspan="2">16 -- 4</td><td>16</td><td>14</td><td>75</td><td>380</td><td>19,0</td><td>1,33</td><td>75</td><td>480</td><td>24,0</td><td>1,33</td><td>120</td><td>750</td><td>37,5</td><td>0,83</td></tr>
<tr><td>2</td><td>20</td><td>14</td><td>75</td><td>480</td><td>24,0</td><td>1,33</td><td>75</td><td>600</td><td>30,0</td><td>1,33</td><td>120</td><td>960</td><td>48,0</td><td>0,83</td></tr>
<tr><td>3</td><td rowspan="2">20 -- 5</td><td>16</td><td>18</td><td>75</td><td>300</td><td>19,0</td><td>1,33</td><td>96</td><td>380</td><td>24,0</td><td>1,04</td><td>150</td><td>750</td><td>47,0</td><td>0,67</td></tr>
<tr><td>4</td><td>20</td><td>18</td><td>60</td><td>300</td><td>19,0</td><td>1,67</td><td>75</td><td>380</td><td>24,0</td><td>1,33</td><td>120</td><td>750</td><td>47,0</td><td>0,83</td></tr>
<tr><td>5</td><td rowspan="2">25 -- 5</td><td>20</td><td>23</td><td>60</td><td>240</td><td>19,0</td><td>1,67</td><td>75</td><td>300</td><td>23,5</td><td>1,33</td><td>150</td><td>600</td><td>47,0</td><td>0,67</td></tr>
<tr><td>6</td><td>30</td><td>23</td><td>60</td><td>300</td><td>23,5</td><td>1,67</td><td>60</td><td>300</td><td>23,5</td><td>1,67</td><td>120</td><td>600</td><td>47,0</td><td>0,83</td></tr>
<tr><td>7</td><td rowspan="2">28 -- 5</td><td>20</td><td>25</td><td>60</td><td>240</td><td>21,0</td><td>1,67</td><td>60</td><td>190</td><td>17,5</td><td>1,67</td><td>120</td><td>380</td><td>33,5</td><td>0,83</td></tr>
<tr><td>8</td><td>30</td><td>25</td><td>48</td><td>240</td><td>21,0</td><td>2,08</td><td>48</td><td>190</td><td>17,5</td><td>2,08</td><td>96</td><td>380</td><td>33,5</td><td>1,04</td></tr>
<tr><td colspan="8">Индекс</td><td>а</td><td colspan="3"></td><td>б</td><td colspan="3"></td><td>в</td></tr>
</table>



```text
┌───────────────────────────────────────────────────────────────────────────────────┬──────────────────────────────┐
│Основное время на 100 мм расчетной длины                                           │Горизонтально-расточные станки│
│Фрезерование пазов, Rz 40 - Rz 20                                                  ├──────────────────────────────┤
│Сталь конструкционная углеродистая, чугун серый, медные сплавы и алюминиевые       │ Фрезы концевые из стали Р6М5 │
│Среднесерийное производство                                                        ├────────────────────┬─────────┤
│                                                                                   │     Карта 115      │ Лист 2  │
├───────────────────────────────────────────────────────────────────────────────────┴────────────────────┴─────────┤
│           Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:            │
├──────────────────────────┬─────────────────┬────────────────────────────────┬────────────────────────────────────┤
│Группы обрабатываемой     │Группа стали     │    Углеродистые, хромистые,    │Марганцовистые, хромомарганцовистые,│
│стали и предела прочности │                 │   никелевые, хромоникелевые    │ хромомолибденовые и близкие к ним  │
│                          ├─────────────────┼─────────┬───────────┬──────────┼──────────┬────────────┬────────────┤
│                          │Предел прочности │до 0,59  │0,59 - 0,74│свыше 0,74│до 0,59   │0,59 - 0,74 │свыше 0,74  │
│                          │сигма , ГПа      │         │           │          │          │            │            │
│                          │     в           │         │           │          │          │            │            │
│                          ├─────────────────┼─────────┼───────────┼──────────┼──────────┼────────────┼────────────┤
│                          │                 │         │┌───┐      │          │          │            │            │
│                          │Коэффициент      │0,8      ││1,0│      │1,25      │1,1       │1,2         │1,35        │
│                          │                 │         │└───┘      │          │          │            │            │
├──────────────────────────┼─────────────────┼─────────┴───────────┴──────────┼──────────┴────────────┴────────────┤
│Твердости чугуна          │Твердость НВ, ГПа│до 2,15                         │свыше 2,15                          │
│                          ├─────────────────┼────────────────────────────────┼────────────────────────────────────┤
│                          │                 │┌───┐                           │                                    │
│                          │Коэффициент      ││1,0│                           │1,25                                │
│                          │                 │└───┘                           │                                    │
├──────────────────────────┼─────────────────┼────────────────────────────────┼────────────────────────────────────┤
│Группы медных сплавов и   │Группа сплавов   │           Гомогенные           │Гетерогенные                        │
│твердости                 ├─────────────────┼───────────────┬────────────────┼────────────────────────────────────┤
│                          │Твердость НВ, ГПа│0,59 - 0,74    │0,98 - 1,37     │1,47 - 2,15                         │
│                          ├─────────────────┼───────────────┼────────────────┼────────────────────────────────────┤
│                          │                 │               │┌───┐           │                                    │
│                          │Коэффициент      │0,55           ││1,0│           │1,25                                │
│                          │                 │               │└───┘           │                                    │
├──────────────────────────┼─────────────────┼───────────────┴────────────────┼────────────────────────────────────┤
│Группы алюминиевых сплавов│Группа сплавов   │Силумин и литейные сплавы       │Дюралюминий                         │
│и твердости               ├─────────────────┼────────────────────────────────┼────────────────────────────────────┤
│                          │Твердость НВ, ГПа│до 0,64                         │до 0,98                             │
│                          ├─────────────────┼────────────────────────────────┼────────────────────────────────────┤
│                          │Коэффициент      │0,75                            │0,7                                 │
└──────────────────────────┴─────────────────┴────────────────────────────────┴────────────────────────────────────┘
```



<table>
<colgroup><col width="7%"><col width="9%"><col width="2%"><col width="8%"><col width="9%"><col width="3%"><col width="7%"><col width="2%"><col width="7%"><col width="5%"><col width="5%"><col width="3%"><col width="5%"><col width="3%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="9%"></colgroup>
<tr><td colspan="19">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Фрезерование Т-образных пазов, Rz 40 - Rz 20, 1Т11 квалитет</td></tr>
<tr><td colspan="19">Сталь, чугун Фрезы концевые из стали Р6М5 Среднесерийное производство</td></tr>
<tr><td colspan="19">Карта 116</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фрезы D, мм, и число зубьев</td><td colspan="2" rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="2">Величина врезания и перебега l , l ,</td><td colspan="6">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="6">Чугун серый, НВ = 1,76 - 2,15 ГПа</td></tr>
<tr><td rowspan="2">z</td><td colspan="2" rowspan="2">1 2 мм</td><td colspan="4">Режимы резания</td><td colspan="2" rowspan="2">t , о 100 мин.</td><td colspan="5">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td colspan="2">S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td colspan="2">S , м мм/мин.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td colspan="19">Для станков мощностью 4,5 - 10 кВт</td></tr>
<tr><td>1</td><td>18 -- 6</td><td colspan="2">18</td><td>8</td><td colspan="2">18</td><td colspan="2">60</td><td>480</td><td>27</td><td colspan="2">1,66</td><td colspan="2">75</td><td>380</td><td colspan="2">21</td><td>1,33</td></tr>
<tr><td>2</td><td>21 -- 8</td><td colspan="2">21</td><td>9</td><td colspan="2">21</td><td colspan="2">60</td><td>380</td><td>25</td><td colspan="2">1,66</td><td colspan="2">75</td><td>300</td><td colspan="2">20</td><td>1,33</td></tr>
<tr><td>3</td><td>25 -- 8</td><td colspan="2">25</td><td>10</td><td colspan="2">25</td><td colspan="2">75</td><td>300</td><td>24</td><td colspan="2">1,33</td><td colspan="2">96</td><td>240</td><td colspan="2">19</td><td>1,04</td></tr>
<tr><td>4</td><td>32 -- 8</td><td colspan="2">32</td><td>14</td><td colspan="2">32</td><td colspan="2">75</td><td>300</td><td>30</td><td colspan="2">1,33</td><td colspan="2">96</td><td>240</td><td colspan="2">24</td><td>1,04</td></tr>
<tr><td>5</td><td>40 -- 8</td><td colspan="2">40</td><td>18</td><td colspan="2">40</td><td colspan="2">60</td><td>240</td><td>30</td><td colspan="2">1,66</td><td colspan="2">75</td><td>190</td><td colspan="2">24</td><td>1,33</td></tr>
<tr><td>6</td><td>50 -- 6</td><td colspan="2">50</td><td>22</td><td colspan="2">50</td><td colspan="2">60</td><td>240</td><td>37</td><td colspan="2">1,66</td><td colspan="2">75</td><td>190</td><td colspan="2">30</td><td>1,33</td></tr>
<tr><td>7</td><td>60 -- 8</td><td colspan="2">60</td><td>28</td><td colspan="2">60</td><td colspan="2">48</td><td>150</td><td>28</td><td colspan="2">2,08</td><td colspan="2">60</td><td>120</td><td colspan="2">23</td><td>1,66</td></tr>
<tr><td>8</td><td>72 -- 8</td><td colspan="2">72</td><td>33</td><td colspan="2">72</td><td colspan="2">38</td><td>150</td><td>34</td><td colspan="2">2,83</td><td colspan="2">48</td><td>120</td><td colspan="2">27</td><td>2,08</td></tr>
<tr><td>9</td><td>85 -- 8</td><td colspan="2">85</td><td>37</td><td colspan="2">85</td><td colspan="2">30</td><td>120</td><td>32</td><td colspan="2">3,33</td><td colspan="2">38</td><td>96</td><td colspan="2">26</td><td>2,63</td></tr>
<tr><td>10</td><td>95 -- 8</td><td colspan="2">95</td><td>41</td><td colspan="2">95</td><td colspan="2">24</td><td>96</td><td>28</td><td colspan="2">4,16</td><td colspan="2">30</td><td>75</td><td colspan="2">18</td><td>3,33</td></tr>
<tr><td colspan="11">Индекс</td><td colspan="2">а</td><td colspan="5"></td><td>б</td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3" rowspan="3">Группы стали и предела прочности</td><td colspan="3">Группа стали</td><td colspan="6">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="7">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="4">0,59 - 0,74 свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td colspan="3">Коэффициент</td><td colspan="2">0,8</td><td colspan="4">1,0 1,25</td><td colspan="2">1,1</td><td colspan="3">1,2</td><td colspan="2">1,35</td></tr>
<tr><td colspan="3" rowspan="2">Твердости чугуна</td><td colspan="3">Твердость чугуна НВ, ГПа</td><td colspan="6">до 2,15</td><td colspan="7">свыше 2,15</td></tr>
<tr><td colspan="3">Коэффициент</td><td colspan="6">1,0</td><td colspan="7">1,25</td></tr>
</table>



<table>
<colgroup><col width="7%"><col width="9%"><col width="2%"><col width="8%"><col width="9%"><col width="4%"><col width="5%"><col width="3%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="3%"><col width="5%"><col width="3%"><col width="5%"><col width="5%"><col width="2%"><col width="3%"><col width="9%"></colgroup>
<tr><td colspan="20">Основное время на 100 мм расчетной длины Горизонтально-расточные станки Фрезерование пазов типа "Ласточкин хвост", Rz 40 - Rz 20, 1Т11 квалитет Фрезы концевые из стали Р6М5 Сталь, чугун</td></tr>
<tr><td colspan="20">Среднесерийное производство Карта 117</td></tr>
<tr><td rowspan="3">N позиции</td><td>Диаметр фрезы D, мм, и число зубьев</td><td colspan="2">Величина на наклонной плоскости угла,</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="2">Величина врезания и перебега l , l ,</td><td colspan="7">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="6">Чугун серый, НВ = 1,76 - 2,15 ГПа</td></tr>
<tr><td rowspan="2">z</td><td colspan="2" rowspan="2">градус</td><td colspan="2" rowspan="2">1 2 мм</td><td colspan="5">Режимы резания</td><td colspan="2" rowspan="2">t , о 100 мин.</td><td colspan="5">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td colspan="2">S , м мм/мин.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td><td colspan="2">S , м мм/мин.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td colspan="20">Для станков мощностью 4,5 - 10 кВт</td></tr>
<tr><td>1</td><td>10 -- 8</td><td colspan="2">70 - 80</td><td>6</td><td colspan="2">9</td><td colspan="2">240</td><td>1500</td><td colspan="2">47</td><td colspan="2">0,42</td><td colspan="2">300</td><td>1500</td><td colspan="2">47</td><td>0,33</td></tr>
<tr><td>2</td><td rowspan="2">16 -- 10</td><td colspan="2">60 - 65</td><td rowspan="2">8</td><td colspan="2">16</td><td colspan="2">300</td><td>1500</td><td colspan="2">75</td><td colspan="2">0,33</td><td colspan="2">190</td><td>750</td><td colspan="2">37</td><td>0,52</td></tr>
<tr><td>3</td><td colspan="2">70 - 80</td><td colspan="2">15</td><td colspan="2">380</td><td>1500</td><td colspan="2">75</td><td colspan="2">0,26</td><td colspan="2">240</td><td>960</td><td colspan="2">48</td><td>0,42</td></tr>
<tr><td>4</td><td rowspan="3">25 -- 12</td><td colspan="2">55 - 60</td><td rowspan="3">10</td><td colspan="2">25</td><td colspan="2">190</td><td>900</td><td colspan="2">70</td><td colspan="2">0,52</td><td colspan="2">120</td><td>480</td><td colspan="2">37</td><td>0,83</td></tr>
<tr><td>5</td><td colspan="2">65 - 70</td><td colspan="2">24</td><td colspan="2">240</td><td>900</td><td colspan="2">70</td><td colspan="2">0,42</td><td colspan="2">190</td><td>600</td><td colspan="2">47</td><td>0,52</td></tr>
<tr><td>6</td><td colspan="2">75 - 80</td><td colspan="2">22</td><td colspan="2">380</td><td>1200</td><td colspan="2">94</td><td colspan="2">0,26</td><td colspan="2">300</td><td>750</td><td colspan="2">59</td><td>0,33</td></tr>
<tr><td colspan="12">Индекс</td><td colspan="2">а</td><td colspan="5"></td><td>б</td></tr>
<tr><td colspan="20">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="3" rowspan="5">Группы стали и предела прочности</td><td colspan="3">Группа стали</td><td colspan="7">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="7">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="2">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="2">свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="2" rowspan="3">0,8</td><td colspan="3"></td><td colspan="2" rowspan="3">1,25</td><td colspan="2" rowspan="3">1,1</td><td colspan="3" rowspan="3">1,2</td><td colspan="2" rowspan="3">1,35</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="3" rowspan="4">Твердости чугуна</td><td colspan="3">Твердость чугуна НВ, ГПа</td><td colspan="7">до 2,15</td><td colspan="7">свыше 2,15</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="7"></td><td colspan="7" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="6"></td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="13">Основное время на 100 мм расчетной длины Фрезерование плоскостей и уступов, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Сталь конструкционная углеродистая, чугун серый, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="5">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 118</td><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность станка N , д</td><td>Диаметр фрезы D, мм, и число зубьев</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , l ,</td><td colspan="4">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="4">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="4">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="2">кВт, до</td><td rowspan="2">z</td><td rowspan="2">1 2 мм</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>1</td><td rowspan="22">7,5 - 10</td><td rowspan="4">80 -- 10</td><td rowspan="2">6</td><td>12</td><td>31</td><td>120</td><td>120</td><td>30,0</td><td>0,83</td><td>190</td><td>120</td><td>30,0</td><td>0,53</td><td>380</td><td>240</td><td>60,0</td><td>0,26</td></tr>
<tr><td>2</td><td>18</td><td>36</td><td>96</td><td>96</td><td>24,0</td><td>1,04</td><td>150</td><td>96</td><td>24,0</td><td>0,67</td><td>300</td><td>190</td><td>47,5</td><td>0,33</td></tr>
<tr><td>3</td><td rowspan="2">18</td><td>5</td><td>22</td><td>120</td><td>120</td><td>30,0</td><td>0,83</td><td>240</td><td>150</td><td>37,5</td><td>0,42</td><td>480</td><td>300</td><td>75,0</td><td>0,21</td></tr>
<tr><td>4</td><td>12</td><td>31</td><td>96</td><td>96</td><td>24,0</td><td>1,04</td><td>190</td><td>120</td><td>30,0</td><td>0,53</td><td>380</td><td>240</td><td>60,0</td><td>0,26</td></tr>
<tr><td>5</td><td rowspan="4">100 --- 10</td><td rowspan="2">6</td><td>18</td><td>42</td><td>75</td><td>75</td><td>23,5</td><td>1,33</td><td>150</td><td>75</td><td>23,5</td><td>0,67</td><td>300</td><td>150</td><td>47,0</td><td>0,33</td></tr>
<tr><td>6</td><td>27</td><td>48</td><td>60</td><td>60</td><td>19,0</td><td>1,67</td><td>120</td><td>60</td><td>19,0</td><td>0,83</td><td>240</td><td>120</td><td>38,0</td><td>0,42</td></tr>
<tr><td>7</td><td rowspan="2">18</td><td>5</td><td>25</td><td>96</td><td>96</td><td>30,0</td><td>1,04</td><td>190</td><td>96</td><td>30,0</td><td>0,58</td><td>380</td><td>190</td><td>60,0</td><td>0,26</td></tr>
<tr><td>8</td><td>12</td><td>35</td><td>75</td><td>75</td><td>23,5</td><td>1,33</td><td>150</td><td>75</td><td>23,5</td><td>0,67</td><td>300</td><td>150</td><td>47,0</td><td>0,33</td></tr>
<tr><td>9</td><td rowspan="4">125 --- 10</td><td rowspan="2">8</td><td>18</td><td>47</td><td>60</td><td>60</td><td>23,5</td><td>1,67</td><td>120</td><td>60</td><td>23,5</td><td>0,83</td><td>240</td><td>120</td><td>47,0</td><td>0,42</td></tr>
<tr><td>10</td><td>27</td><td>56</td><td>60</td><td>60</td><td>23,5</td><td>1,67</td><td>96</td><td>48</td><td>19,0</td><td>1,04</td><td>190</td><td>96</td><td>37,5</td><td>0,53</td></tr>
<tr><td>11</td><td rowspan="2">27</td><td>5</td><td>28</td><td>75</td><td>75</td><td>29,5</td><td>1,33</td><td>150</td><td>75</td><td>29,5</td><td>0,67</td><td>300</td><td>150</td><td>59,0</td><td>0,33</td></tr>
<tr><td>12</td><td>12</td><td>40</td><td>60</td><td>60</td><td>23,5</td><td>1,67</td><td>120</td><td>75</td><td>29,5</td><td>0,83</td><td>240</td><td>150</td><td>59,0</td><td>0,42</td></tr>
<tr><td>13</td><td rowspan="5">160 --- 16</td><td rowspan="3">8</td><td>18</td><td>54</td><td>75</td><td>48</td><td>24,0</td><td>1,33</td><td>120</td><td>48</td><td>24,0</td><td>0,83</td><td>240</td><td>96</td><td>48,0</td><td>0,42</td></tr>
<tr><td>14</td><td>27</td><td>65</td><td>60</td><td>38</td><td>19,0</td><td>1,67</td><td>120</td><td>38</td><td>19,0</td><td>0,83</td><td>240</td><td>75</td><td>37,5</td><td>0,42</td></tr>
<tr><td>15</td><td>40</td><td>73</td><td>60</td><td>38</td><td>19,0</td><td>1,67</td><td>96</td><td>30</td><td>15,0</td><td>1,04</td><td>190</td><td>60</td><td>30,0</td><td>0,53</td></tr>
<tr><td>16</td><td rowspan="2">40</td><td>5</td><td>31</td><td>96</td><td>60</td><td>30,0</td><td>1,04</td><td>150</td><td>60</td><td>30,0</td><td>0,67</td><td>300</td><td>120</td><td>60,0</td><td>0,33</td></tr>
<tr><td>17</td><td>12</td><td>46</td><td>75</td><td>48</td><td>24,0</td><td>1,33</td><td>150</td><td>48</td><td>24,0</td><td>0,67</td><td>300</td><td>96</td><td>48,0</td><td>0,33</td></tr>
<tr><td>18</td><td rowspan="5">200 --- 16</td><td rowspan="3">12</td><td>27</td><td>74</td><td>60</td><td>38</td><td>24,0</td><td>1,67</td><td>96</td><td>38</td><td>24,0</td><td>1,04</td><td>240</td><td>96</td><td>60,0</td><td>0,42</td></tr>
<tr><td>19</td><td>40</td><td>84</td><td>48</td><td>30</td><td>19,0</td><td>2,08</td><td>75</td><td>30</td><td>19,0</td><td>1,33</td><td>190</td><td>75</td><td>47,0</td><td>0,53</td></tr>
<tr><td>20</td><td>60</td><td>96</td><td>48</td><td>30</td><td>19,0</td><td>2,08</td><td>60</td><td>24</td><td>15,0</td><td>1,67</td><td>150</td><td>60</td><td>38,0</td><td>0,67</td></tr>
<tr><td>21</td><td rowspan="2">40</td><td>5</td><td>35</td><td>75</td><td>48</td><td>24,0</td><td>1,33</td><td>150</td><td>48</td><td>30,0</td><td>0,67</td><td>380</td><td>120</td><td>75,0</td><td>0,26</td></tr>
<tr><td>22</td><td>12</td><td>52</td><td>60</td><td>38</td><td>19,0</td><td>1,67</td><td>120</td><td>38</td><td>24,0</td><td>0,83</td><td>300</td><td>96</td><td>60,0</td><td>0,33</td></tr>
<tr><td colspan="8">Индекс</td><td>а</td><td colspan="4"></td><td>б</td><td colspan="3"></td><td>в</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="13">Основное время на 100 мм расчетной длины Фрезерование плоскостей и уступов, Rz 80, 1Т14 - 1Т12 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Сталь конструкционная углеродистая, чугун серый, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="5">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 118</td><td colspan="2">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность станка N , д</td><td>Диаметр фрезы D, мм, и число зубьев</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , l ,</td><td colspan="4">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="4">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="4">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="2">кВт, до</td><td rowspan="2">z</td><td rowspan="2">1 2 мм</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>1</td><td rowspan="10">7,5 - 10</td><td rowspan="5">250 --- 20</td><td rowspan="3">12</td><td>27</td><td>83</td><td>48</td><td>24</td><td>19,0</td><td>2,08</td><td>96</td><td>24</td><td>19,0</td><td>1,04</td><td>240</td><td>60</td><td>47,0</td><td>0,42</td></tr>
<tr><td>2</td><td>40</td><td>96</td><td>48</td><td>24</td><td>19,0</td><td>2,08</td><td>75</td><td>19</td><td>15,0</td><td>1,33</td><td>190</td><td>48</td><td>38,0</td><td>0,53</td></tr>
<tr><td>3</td><td>60</td><td>111</td><td>38</td><td>19</td><td>15,0</td><td>2,63</td><td>60</td><td>19</td><td>15,0</td><td>1,67</td><td>150</td><td>48</td><td>38,0</td><td>0,67</td></tr>
<tr><td>4</td><td rowspan="2">40</td><td>5</td><td>39</td><td>60</td><td>30</td><td>23,5</td><td>1,67</td><td>120</td><td>38</td><td>30,0</td><td>0,83</td><td>300</td><td>96</td><td>75,0</td><td>0,33</td></tr>
<tr><td>5</td><td>12</td><td>58</td><td>48</td><td>24</td><td>19,0</td><td>2,08</td><td>120</td><td>30</td><td>23,5</td><td>0,83</td><td>300</td><td>75</td><td>59,0</td><td>0,33</td></tr>
<tr><td>6</td><td rowspan="5">315 --- 22</td><td rowspan="3">12</td><td>27</td><td>90</td><td>38</td><td>19</td><td>19,0</td><td>2,63</td><td>75</td><td>19</td><td>19,0</td><td>1,33</td><td>190</td><td>48</td><td>47,5</td><td>0,53</td></tr>
<tr><td>7</td><td>40</td><td>110</td><td>38</td><td>19</td><td>19,0</td><td>2,63</td><td>60</td><td>15</td><td>15,0</td><td>1,67</td><td>150</td><td>38</td><td>37,5</td><td>0,67</td></tr>
<tr><td>8</td><td>60</td><td>130</td><td>30</td><td>15</td><td>15,0</td><td>3,33</td><td>60</td><td>15</td><td>15,0</td><td>1,67</td><td>150</td><td>38</td><td>37,5</td><td>0,67</td></tr>
<tr><td>9</td><td rowspan="2">40</td><td>5</td><td>45</td><td>48</td><td>24</td><td>24,0</td><td>2,08</td><td>120</td><td>30</td><td>30,0</td><td>0,83</td><td>300</td><td>75</td><td>75,0</td><td>0,33</td></tr>
<tr><td>10</td><td>12</td><td>65</td><td>38</td><td>19</td><td>19,0</td><td>2,63</td><td>96</td><td>24</td><td>24,0</td><td>1,04</td><td>240</td><td>60</td><td>60,0</td><td>0,42</td></tr>
<tr><td colspan="9">Индекс</td><td>а</td><td colspan="3"></td><td>б</td><td colspan="3"></td><td>в</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="13">Основное время на 100 мм расчетной длины Фрезерование плоскостей и уступов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Сталь конструкционная углеродистая, чугун серый, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="5">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 119</td><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность станка N , д</td><td>Диаметр фрезы D, мм, и число зубьев</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , l ,</td><td colspan="4">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="4">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="4">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="2">кВт, до</td><td rowspan="2">z</td><td rowspan="2">1 2 мм</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>1</td><td rowspan="17">7,5 - 10</td><td>80 --- 10</td><td rowspan="17">2</td><td>18</td><td>72</td><td>120</td><td>120</td><td>30,0</td><td>0,83</td><td>190</td><td>120</td><td>30,0</td><td>0,53</td><td>380</td><td>240</td><td>60</td><td>0,26</td></tr>
<tr><td>2</td><td rowspan="2">100 --- 10</td><td>18</td><td>84</td><td>96</td><td>96</td><td>30,0</td><td>1,04</td><td>150</td><td>96</td><td>30,0</td><td>0,67</td><td>300</td><td>190</td><td>60</td><td>0,33</td></tr>
<tr><td>3</td><td>27</td><td>96</td><td>75</td><td>75</td><td>23,5</td><td>1,33</td><td>150</td><td>96</td><td>30,0</td><td>0,67</td><td>300</td><td>190</td><td>60</td><td>0,33</td></tr>
<tr><td>4</td><td rowspan="2">125 --- 10</td><td>18</td><td>94</td><td>75</td><td>75</td><td>29,5</td><td>1,33</td><td>120</td><td>75</td><td>29,5</td><td>0,83</td><td>300</td><td>190</td><td>75</td><td>0,33</td></tr>
<tr><td>5</td><td>27</td><td>112</td><td>60</td><td>60</td><td>23,5</td><td>1,67</td><td>120</td><td>75</td><td>29,5</td><td>0,83</td><td>240</td><td>150</td><td>59</td><td>0,42</td></tr>
<tr><td>6</td><td rowspan="3">160 --- 16</td><td>40</td><td>108</td><td>75</td><td>60</td><td>30,0</td><td>1,33</td><td>150</td><td>60</td><td>30,0</td><td>0,67</td><td>300</td><td>120</td><td>60</td><td>0,33</td></tr>
<tr><td>7</td><td>27</td><td>130</td><td>48</td><td>48</td><td>24,0</td><td>2,08</td><td>120</td><td>48</td><td>24,0</td><td>0,83</td><td>240</td><td>96</td><td>48</td><td>0,42</td></tr>
<tr><td>8</td><td>0</td><td>146</td><td>48</td><td>48</td><td>24,0</td><td>2,08</td><td>96</td><td>38</td><td>19,0</td><td>1,04</td><td>240</td><td>96</td><td>48</td><td>0,42</td></tr>
<tr><td>9</td><td rowspan="3">200 --- 16</td><td>27</td><td>148</td><td>48</td><td>48</td><td>30,0</td><td>2,08</td><td>96</td><td>38</td><td>24,0</td><td>1,04</td><td>240</td><td>96</td><td>60</td><td>0,53</td></tr>
<tr><td>10</td><td>40</td><td>168</td><td>38</td><td>38</td><td>24,0</td><td>2,63</td><td>96</td><td>38</td><td>24,0</td><td>1,04</td><td>240</td><td>75</td><td>47</td><td>0,42</td></tr>
<tr><td>11</td><td>60</td><td>192</td><td>38</td><td>38</td><td>24,0</td><td>2,63</td><td>75</td><td>30</td><td>19,0</td><td>1,33</td><td>190</td><td>75</td><td>47</td><td>0,53</td></tr>
<tr><td>12</td><td rowspan="3">250 --- 20</td><td>27</td><td>166</td><td>48</td><td>38</td><td>30,0</td><td>2,08</td><td>96</td><td>30</td><td>23,5</td><td>1,04</td><td>240</td><td>75</td><td>59</td><td>0,42</td></tr>
<tr><td>13</td><td>40</td><td>192</td><td>38</td><td>30</td><td>23,5</td><td>2,63</td><td>75</td><td>24</td><td>19,0</td><td>1,33</td><td>190</td><td>60</td><td>47</td><td>0,53</td></tr>
<tr><td>14</td><td>60</td><td>222</td><td>38</td><td>30</td><td>23,5</td><td>2,63</td><td>75</td><td>24</td><td>19,0</td><td>1,33</td><td>190</td><td>60</td><td>47</td><td>0,43</td></tr>
<tr><td>15</td><td rowspan="3">315 --- 22</td><td>27</td><td>180</td><td>38</td><td>30</td><td>37,5</td><td>2,63</td><td>75</td><td>24</td><td>24,0</td><td>1,33</td><td>190</td><td>60</td><td>60</td><td>0,53</td></tr>
<tr><td>16</td><td>40</td><td>220</td><td>30</td><td>24</td><td>24,0</td><td>3,33</td><td>60</td><td>19</td><td>19,0</td><td>1,67</td><td>150</td><td>48</td><td>48</td><td>0,67</td></tr>
<tr><td>17</td><td>60</td><td>260</td><td>30</td><td>24</td><td>24,0</td><td>3,33</td><td>60</td><td>19</td><td>19,0</td><td>1,67</td><td>150</td><td>48</td><td>48</td><td>0,67</td></tr>
<tr><td colspan="9">Индекс</td><td>а</td><td colspan="3"></td><td>б</td><td colspan="3"></td><td>в</td></tr>
</table>



```text
┌──────────────────────────────────────────────────────────────────────────────────────────┬──────────────────────────────┐
│Основное время на 100 мм расчетной длины                                                  │Горизонтально-расточные станки│
│Фрезерование плоскостей и уступов, Rz 40 - Rz 20, 1Т11 квалитет                           ├──────────────────────────────┤
│Сталь конструкционная углеродистая, чугун серый, медные сплавы и алюминиевые              │ Фрезы концевые из стали Р6М5 │
│Среднесерийное производство                                                               ├───────────────────┬──────────┤
│                                                                                          │     Карта 119     │  Лист 2  │
├──────────────────────────────────────────────────────────────────────────────────────────┴───────────────────┴──────────┤
│               Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:               │
├──────────────────────────┬──────────────────┬──────────────────────────────────────┬────────────────────────────────────┤
│Группы обрабатываемой     │Группа стали      │ Углеродистые, хромистые, никелевые,  │Марганцовистые, хромомарганцовистые,│
│стали и предела прочности │                  │            хромоникелевые            │ хромомолибденовые и близкие к ним  │
│                          ├──────────────────┼───────────┬────────────┬─────────────┼──────────┬────────────┬────────────┤
│                          │Предел прочности  │до 0,59    │0,59 - 0,74 │свыше 0,74   │до 0,59   │0,59 - 0,74 │свыше 0,74  │
│                          │сигма , ГПа       │           │            │             │          │            │            │
│                          │     в            │           │            │             │          │            │            │
│                          ├──────────────────┼───────────┼────────────┼─────────────┼──────────┼────────────┼────────────┤
│                          │                  │           │┌───┐       │             │          │            │            │
│                          │Коэффициент       │0,8        ││1,0│       │1,25         │1,1       │1,2         │1,35        │
│                          │                  │           │└───┘       │             │          │            │            │
├──────────────────────────┼──────────────────┼───────────┴────────────┴─────────────┼──────────┴────────────┴────────────┤
│Твердости чугуна          │Твердость НВ, ГПа │до 2,15                               │свыше 2,15                          │
│                          ├──────────────────┼──────────────────────────────────────┼────────────────────────────────────┤
│                          │                  │┌───┐                                 │                                    │
│                          │Коэффициент       ││1,0│                                 │1,25                                │
│                          │                  │└───┘                                 │                                    │
├──────────────────────────┼──────────────────┼─────────────────┬────────────────────┴────────────────────────────────────┤
│Группы медных сплавов     │Группа сплавов    │Гомогенные       │                      Гетерогенные                       │
│и твердости               ├──────────────────┼─────────────────┼────────────────────┬────────────────────────────────────┤
│                          │Твердость НВ, ГПа │0,59 - 0,74      │0,98 - 1,37         │1,47 - 2,15                         │
│                          ├──────────────────┼─────────────────┼────────────────────┼────────────────────────────────────┤
│                          │                  │                 │┌───┐               │                                    │
│                          │Коэффициент       │0,55             ││1,0│               │1,25                                │
│                          │                  │                 │└───┘               │                                    │
├──────────────────────────┼──────────────────┼─────────────────┴────────────────────┼────────────────────────────────────┤
│Группы алюминиевых сплавов│Группа сплавов    │Силумин и литейные сплавы             │Дюралюминий                         │
│и твердости               ├──────────────────┼──────────────────────────────────────┼────────────────────────────────────┤
│                          │Твердость НВ, ГПа │до 0,64                               │до 0,98                             │
│                          ├──────────────────┼──────────────────────────────────────┼────────────────────────────────────┤
│                          │Коэффициент       │0,75                                  │0,7                                 │
└──────────────────────────┴──────────────────┴──────────────────────────────────────┴────────────────────────────────────┘

┌──────────────────────────────────────────────────────────────────────────────────────────┬──────────────────────────────┐
│Основное время на 100 мм расчетной длины                                                  │Горизонтально-расточные станки│
│Фрезерование плоскостей и уступов, Rz 80, 1Т14 - 1Т12 квалитет                            ├──────────────────────────────┤
│Сталь конструкционная углеродистая, чугун серый, медные сплавы и алюминиевые              │ Фрезы дисковые трехсторонние │
│Среднесерийное производство                                                               │        из стали Р6М5         │
│                                                                                          ├────────────────────┬─────────┤
│                                                                                          │     Карта 119      │ Лист 3  │
├──────────────────────────────────────────────────────────────────────────────────────────┴────────────────────┴─────────┤
│               Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:               │
├──────────────────────────┬──────────────────┬──────────────────────────────────────┬────────────────────────────────────┤
│Группы обрабатываемой     │Группа стали      │ Углеродистые, хромистые, никелевые,  │Марганцовистые, хромомарганцовистые,│
│стали и предела прочности │                  │           хромоникелевые             │ хромомолибденовые и близкие к ним  │
│                          ├──────────────────┼───────────┬─────────────┬────────────┼───────────┬────────────┬───────────┤
│                          │Предел прочности  │до 0,59    │0,59 - 0,74  │свыше 0,74  │до 0,59    │0,59 - 0,74 │свыше 0,74 │
│                          │сигма , ГПа       │           │             │            │           │            │           │
│                          │     в            │           │             │            │           │            │           │
│                          ├──────────────────┼───────────┼─────────────┼────────────┼───────────┼────────────┼───────────┤
│                          │                  │           │┌───┐        │            │           │            │           │
│                          │Коэффициент       │0,8        ││1,0│        │1,25        │1,1        │1,2         │1,35       │
│                          │                  │           │└───┘        │            │           │            │           │
├──────────────────────────┼──────────────────┼───────────┴─────────────┴────────────┼───────────┴────────────┴───────────┤
│Твердости чугуна          │Твердость НВ, ГПа │до 2,15                               │свыше 2,15                          │
│                          ├──────────────────┼──────────────────────────────────────┼────────────────────────────────────┤
│                          │                  │┌───┐                                 │                                    │
│                          │Коэффициент       ││1,0│                                 │1,25                                │
│                          │                  │└───┘                                 │                                    │
├──────────────────────────┼──────────────────┼──────────────────────────────────────┼────────────────────────────────────┤
│Группы медных сплавов     │Группа сплавов    │              Гомогенные              │Гетерогенные                        │
│и твердости               ├──────────────────┼──────────────────┬───────────────────┼────────────────────────────────────┤
│                          │Твердость НВ, ГПа │0,59 - 0,74       │0,98 - 1,37        │1,47 - 2,15                         │
│                          ├──────────────────┼──────────────────┼───────────────────┼────────────────────────────────────┤
│                          │                  │                  │┌───┐              │                                    │
│                          │Коэффициент       │0,55              ││1,0│              │1,25                                │
│                          │                  │                  │└───┘              │                                    │
├──────────────────────────┼──────────────────┼──────────────────┴───────────────────┼────────────────────────────────────┤
│Группы алюминиевых сплавов│Группа сплавов    │Силумин и литейные сплавы             │Дюралюминий                         │
│и твердости               ├──────────────────┼──────────────────────────────────────┼────────────────────────────────────┤
│                          │Твердость НВ, ГПа │до 0,64                               │до 0,98                             │
│                          ├──────────────────┼──────────────────────────────────────┼────────────────────────────────────┤
│                          │Коэффициент       │0,75                                  │0,7                                 │
├──────────────────────────┼──────────────────┼──────────────────────────────────────┼────────────────────────────────────┤
│Состояния обрабатываемой  │Состояние         │без корки                             │по корке                            │
│поверхности               │обрабатываемой    │                                      │                                    │
│                          │поверхности       │                                      │                                    │
│                          ├──────────────────┼──────────────────────────────────────┼────────────────────────────────────┤
│                          │                  │┌───┐                                 │                                    │
│                          │Коэффициент       ││1,0│                                 │1,2                                 │
│                          │                  │└───┘                                 │                                    │
└──────────────────────────┴──────────────────┴──────────────────────────────────────┴────────────────────────────────────┘
```



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="13">Основное время на 100 мм расчетной длины Фрезерование пазов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="13" rowspan="2">Сталь конструкционная углеродистая, чугун серый, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="5">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 120</td><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность станка N , д</td><td>Диаметр фрезы D, мм, и число зубьев</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , l ,</td><td colspan="4">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="4">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="4">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="2">кВт, до</td><td rowspan="2">z</td><td rowspan="2">1 2 мм</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>1</td><td rowspan="23">7,5 - 10</td><td rowspan="3">80 -- 10</td><td rowspan="3">25</td><td>5</td><td>44</td><td>150</td><td>150</td><td>38,0</td><td>0,67</td><td>240</td><td>190</td><td>48,0</td><td>0,42</td><td>380</td><td>300</td><td>75</td><td>0,26</td></tr>
<tr><td>2</td><td>10</td><td>58</td><td>96</td><td>120</td><td>30,0</td><td>1,04</td><td>190</td><td>190</td><td>48,0</td><td>0,53</td><td>300</td><td>300</td><td>75</td><td>0,33</td></tr>
<tr><td>3</td><td>15</td><td>68</td><td>75</td><td>120</td><td>30,0</td><td>1,33</td><td>150</td><td>150</td><td>37,5</td><td>0,67</td><td>300</td><td>300</td><td>75</td><td>0,33</td></tr>
<tr><td>4</td><td rowspan="4">100 --- 10</td><td rowspan="4">28</td><td>5</td><td>50</td><td>120</td><td>120</td><td>37,5</td><td>0,83</td><td>190</td><td>150</td><td>47,0</td><td>0,53</td><td>380</td><td>300</td><td>94</td><td>0,26</td></tr>
<tr><td>5</td><td>10</td><td>66</td><td>75</td><td>96</td><td>30,0</td><td>1,33</td><td>150</td><td>150</td><td>47,0</td><td>0,67</td><td>300</td><td>240</td><td>75</td><td>0,33</td></tr>
<tr><td>6</td><td>15</td><td>78</td><td>60</td><td>96</td><td>30,0</td><td>1,67</td><td>120</td><td>150</td><td>47,0</td><td>0,83</td><td>190</td><td>240</td><td>75</td><td>0,53</td></tr>
<tr><td>7</td><td>20</td><td>86</td><td>48</td><td>96</td><td>30,0</td><td>2,08</td><td>96</td><td>120</td><td>38,0</td><td>1,04</td><td>150</td><td>190</td><td>60</td><td>0,67</td></tr>
<tr><td>8</td><td rowspan="4">125 --- 10</td><td rowspan="4">32</td><td>5</td><td>56</td><td>96</td><td>96</td><td>37,5</td><td>1,04</td><td>150</td><td>120</td><td>47,0</td><td>0,67</td><td>240</td><td>190</td><td>75</td><td>0,42</td></tr>
<tr><td>9</td><td>10</td><td>76</td><td>60</td><td>75</td><td>29,5</td><td>1,67</td><td>120</td><td>120</td><td>47,0</td><td>0,83</td><td>190</td><td>190</td><td>75</td><td>0,53</td></tr>
<tr><td>10</td><td>15</td><td>88</td><td>38</td><td>75</td><td>29,5</td><td>2,63</td><td>96</td><td>96</td><td>37,5</td><td>1,04</td><td>150</td><td>190</td><td>75</td><td>0,67</td></tr>
<tr><td>11</td><td>20</td><td>100</td><td>30</td><td>75</td><td>29,5</td><td>3,33</td><td>75</td><td>96</td><td>37,5</td><td>1,33</td><td>120</td><td>190</td><td>59</td><td>0,83</td></tr>
<tr><td>12</td><td rowspan="4">160 --- 16</td><td rowspan="4">36</td><td>10</td><td>84</td><td>96</td><td>75</td><td>37,5</td><td>1,04</td><td>150</td><td>75</td><td>38,0</td><td>0,67</td><td>300</td><td>150</td><td>75</td><td>0,33</td></tr>
<tr><td>13</td><td>15</td><td>100</td><td>75</td><td>60</td><td>30,0</td><td>1,33</td><td>120</td><td>75</td><td>38,0</td><td>0,83</td><td>240</td><td>150</td><td>75</td><td>0,42</td></tr>
<tr><td>14</td><td>20</td><td>114</td><td>48</td><td>60</td><td>30,0</td><td>2,08</td><td>96</td><td>75</td><td>38,0</td><td>1,04</td><td>190</td><td>150</td><td>75</td><td>0,53</td></tr>
<tr><td>15</td><td>30</td><td>132</td><td>30</td><td>48</td><td>24,0</td><td>3,33</td><td>60</td><td>60</td><td>30,0</td><td>1,67</td><td>120</td><td>120</td><td>60</td><td>0,83</td></tr>
<tr><td>16</td><td rowspan="4">200 --- 16</td><td rowspan="4">40</td><td>5</td><td>96</td><td>75</td><td>48</td><td>24,0</td><td>1,33</td><td>120</td><td>60</td><td>37,5</td><td>0,83</td><td>240</td><td>120</td><td>75</td><td>0,42</td></tr>
<tr><td>17</td><td>10</td><td>114</td><td>60</td><td>48</td><td>24,0</td><td>1,67</td><td>96</td><td>60</td><td>37,5</td><td>1,04</td><td>190</td><td>120</td><td>75</td><td>0,53</td></tr>
<tr><td>18</td><td>20</td><td>128</td><td>38</td><td>48</td><td>24,0</td><td>2,63</td><td>96</td><td>60</td><td>37,5</td><td>1,04</td><td>150</td><td>96</td><td>60</td><td>0,67</td></tr>
<tr><td>19</td><td>30</td><td>152</td><td>30</td><td>48</td><td>24,0</td><td>3,33</td><td>60</td><td>48</td><td>30,0</td><td>1,67</td><td>120</td><td>96</td><td>60</td><td>0,83</td></tr>
<tr><td>20</td><td rowspan="2">250 --- 16</td><td rowspan="4">45</td><td>10</td><td>106</td><td>75</td><td>38</td><td>30,0</td><td>1,33</td><td>120</td><td>48</td><td>37,5</td><td>0,83</td><td>240</td><td>96</td><td>75</td><td>0,42</td></tr>
<tr><td>21</td><td>15</td><td>126</td><td>60</td><td>38</td><td>30,0</td><td>1,67</td><td>96</td><td>48</td><td>37,5</td><td>1,04</td><td>190</td><td>96</td><td>75</td><td>0,53</td></tr>
<tr><td>22</td><td rowspan="2">250 --- 20</td><td>20</td><td>144</td><td>38</td><td>38</td><td>30,0</td><td>2,63</td><td>96</td><td>48</td><td>37,5</td><td>1,04</td><td>190</td><td>96</td><td>75</td><td>0,53</td></tr>
<tr><td>23</td><td>30</td><td>170</td><td>24</td><td>30</td><td>23,5</td><td>4,17</td><td>60</td><td>38</td><td>30,0</td><td>1,67</td><td>120</td><td>75</td><td>59</td><td>0,83</td></tr>
<tr><td colspan="9">Индекс</td><td>а</td><td colspan="3"></td><td>б</td><td colspan="3"></td><td>в</td></tr>
</table>



<table>
<colgroup><col width="3%"><col width="6%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="2%"><col width="5%"><col width="4%"><col width="2%"><col width="2%"><col width="2%"><col width="4%"><col width="7%"><col width="5%"><col width="3%"><col width="7%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"></colgroup>
<tr><td colspan="16">Основное время на 100 мм расчетной длины Фрезерование пазов, Rz 40 - Rz 20, 1Т11 квалитет</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="16" rowspan="2">Сталь конструкционная углеродистая, чугун серый, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="5">Фрезы дисковые трехсторонние из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 120</td><td colspan="2">Лист 2</td></tr>
<tr><td rowspan="3">N позиции</td><td>Мощность станка N , д</td><td>Диаметр фрезы D, мм, и число зубьев</td><td rowspan="3">Ширина фрезерования В, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td>Величина врезания и перебега l , l ,</td><td colspan="7">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="4">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="4">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td rowspan="2">кВт, до</td><td rowspan="2">z</td><td rowspan="2">1 2 мм</td><td colspan="5">Режимы резания</td><td colspan="2" rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td><td colspan="3">Режимы резания</td><td rowspan="2">t , о 100 мин.</td></tr>
<tr><td colspan="2">S , м мм/мин.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td><td>S , м мм/мин.</td><td colspan="2">n, v, об./ м/ мин. мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>24</td><td rowspan="4">7,5... 10</td><td rowspan="4">315 --- 22</td><td rowspan="4">50</td><td>10</td><td>120</td><td colspan="2">60</td><td>30</td><td colspan="2">30,0</td><td colspan="2">1,67</td><td>120</td><td colspan="2">38 37,5</td><td>0,83</td><td>240</td><td>75</td><td>74,0</td><td>0,42</td></tr>
<tr><td>25</td><td>15</td><td>140</td><td colspan="2">48</td><td>30</td><td colspan="2">30,0</td><td colspan="2">2,08</td><td>96</td><td colspan="2">38 37,5</td><td>1,04</td><td>190</td><td>75</td><td>74,0</td><td>0,53</td></tr>
<tr><td>26</td><td>20</td><td>160</td><td colspan="2">30</td><td>30</td><td colspan="2">30,0</td><td colspan="2">3,33</td><td>75</td><td colspan="2">38 37,5</td><td>1,33</td><td>150</td><td>75</td><td>74,0</td><td>0,67</td></tr>
<tr><td>27</td><td>30</td><td>190</td><td colspan="2">19</td><td>24</td><td colspan="2">24,0</td><td colspan="2">5,27</td><td>48</td><td colspan="2">30 30,0</td><td>2,08</td><td>96</td><td>60</td><td>59,5</td><td>1,04</td></tr>
<tr><td colspan="11">Индекс</td><td colspan="2">а</td><td colspan="3"></td><td>б</td><td colspan="3"></td><td>в</td></tr>
<tr><td colspan="21">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="4" rowspan="5">Группы обрабатываемой стали и предела прочности</td><td colspan="3">Группа стали</td><td colspan="8">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="6">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="8">до 0,59 0,59 - 0,74 свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td colspan="2">свыше 0,74</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="8"></td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td colspan="2" rowspan="3">1,35</td></tr>
<tr><td colspan="3">0,8</td><td colspan="5">1,0 1,25</td></tr>
<tr><td colspan="8"></td></tr>
<tr><td colspan="4" rowspan="2">Твердости чугуна</td><td colspan="3">Твердость НВ, ГПа</td><td colspan="8">до 2,15</td><td colspan="6">свыше 2,15</td></tr>
<tr><td colspan="3">Коэффициент</td><td colspan="8">1,0</td><td colspan="6">1,25</td></tr>
<tr><td colspan="4" rowspan="5">Группы медных сплавов и твердости</td><td colspan="3">Группа сплавов</td><td colspan="8">Гомогенные</td><td colspan="6">Гетерогенные</td></tr>
<tr><td colspan="3">Твердость НВ, ГПа</td><td colspan="5">0,59 - 0,74</td><td colspan="3">0,98 - 1,37</td><td colspan="6">1,47 - 2,15</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="5" rowspan="3">0,55</td><td colspan="3"></td><td colspan="6" rowspan="3">1,25</td></tr>
<tr><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="4" rowspan="3">Группы алюминиевых сплавов и твердости</td><td colspan="3">Группа сплавов</td><td colspan="8">Силумин и литейные сплавы</td><td colspan="6">Дюралюминий</td></tr>
<tr><td colspan="3">Твердость НВ, ГПа</td><td colspan="8">до 0,64</td><td colspan="6">до 0,98</td></tr>
<tr><td colspan="3">Коэффициент</td><td colspan="8">0,75</td><td colspan="6">0,7</td></tr>
</table>



<table>
<colgroup><col width="4%"><col width="8%"><col width="8%"><col width="8%"><col width="5%"><col width="5%"><col width="8%"><col width="8%"><col width="5%"><col width="5%"><col width="8%"><col width="8%"><col width="5%"><col width="5%"><col width="8%"></colgroup>
<tr><td colspan="10">Основное время на 100 мм расчетной длины Сверление отверстий</td><td colspan="5">Горизонтально-расточные станки</td></tr>
<tr><td colspan="10" rowspan="2">Сталь, чугун, медные сплавы и алюминиевые Среднесерийное производство</td><td colspan="5">Сверла спиральные из стали Р6М5</td></tr>
<tr><td colspan="3">Карта 121</td><td colspan="2">Лист 1</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Диаметр обрабатываемой поверхности D, мм,</td><td rowspan="3">Длина сверления l, мм, до</td><td colspan="4">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в</td><td colspan="4">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="4">Медные сплавы, НВ = 0,98 - 1,37 ГПа, и алюминиевые</td></tr>
<tr><td colspan="3">Режимы резания</td><td>t , о 100</td><td colspan="3">Режимы резания</td><td>t , о 100</td><td colspan="3">Режимы резания</td><td>t , о 100</td></tr>
<tr><td>до</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>мин.</td><td>S , м мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td>мин.</td></tr>
<tr><td>1</td><td rowspan="2">8</td><td>3D</td><td>0,20</td><td>700</td><td>17,5</td><td>0,71</td><td>0,40</td><td>700</td><td>17,5</td><td>0,36</td><td>0,40</td><td>1500</td><td>38</td><td>0,16</td></tr>
<tr><td>2</td><td>свыше 3D</td><td>0,16</td><td>500</td><td>12,5</td><td>1,25</td><td>0,32</td><td>500</td><td>12,5</td><td>0,62</td><td>0,30</td><td>800</td><td>20</td><td>0,41</td></tr>
<tr><td>3</td><td rowspan="2">10</td><td>3D</td><td>0,25</td><td>550</td><td>17,5</td><td>0,72</td><td>0,50</td><td>500</td><td>15,7</td><td>0,40</td><td>0,50</td><td>1200</td><td>38</td><td>0,16</td></tr>
<tr><td>4</td><td>свыше 3D</td><td>0,20</td><td>380</td><td>12,0</td><td>1,31</td><td>0,40</td><td>350</td><td>11,0</td><td>0,71</td><td>0,40</td><td>600</td><td>19</td><td>0,41</td></tr>
<tr><td>5</td><td rowspan="2">13</td><td>3D</td><td>0,28</td><td>400</td><td>17,5</td><td>0,89</td><td>0,60</td><td>380</td><td>15,5</td><td>0,44</td><td>0,60</td><td>960</td><td>39</td><td>0,17</td></tr>
<tr><td>6</td><td>свыше 3D</td><td>0,22</td><td>300</td><td>12,3</td><td>1,51</td><td>0,50</td><td>250</td><td>10,0</td><td>0,80</td><td>0,45</td><td>500</td><td>20</td><td>0,44</td></tr>
<tr><td>7</td><td rowspan="2">16</td><td>3D</td><td>0,35</td><td>300</td><td>15,0</td><td>0,95</td><td>0,70</td><td>300</td><td>15,0</td><td>0,48</td><td>0,70</td><td>750</td><td>38</td><td>0,19</td></tr>
<tr><td>8</td><td>свыше 3D</td><td>0,28</td><td>200</td><td>10,0</td><td>1,78</td><td>0,56</td><td>200</td><td>10,0</td><td>0,89</td><td>0,50</td><td>400</td><td>20</td><td>0,50</td></tr>
<tr><td>9</td><td rowspan="2">20</td><td>3D</td><td>0,40</td><td>240</td><td>15,0</td><td>1,04</td><td>0,80</td><td>250</td><td>15,5</td><td>0,50</td><td>0,80</td><td>600</td><td>38</td><td>0,21</td></tr>
<tr><td>10</td><td>свыше 3D</td><td>0,32</td><td>160</td><td>10,0</td><td>1,89</td><td>0,63</td><td>160</td><td>10,0</td><td>1,00</td><td>0,60</td><td>320</td><td>20</td><td>0,52</td></tr>
<tr><td>11</td><td rowspan="2">25</td><td>3D</td><td>0,45</td><td>190</td><td>15,0</td><td>1,17</td><td>0,90</td><td>200</td><td>15,5</td><td>0,56</td><td>0,90</td><td>480</td><td>36</td><td>0,23</td></tr>
<tr><td>12</td><td>свыше 3D</td><td>0,36</td><td>130</td><td>10,0</td><td>2,13</td><td>0,70</td><td>135</td><td>10,5</td><td>1,06</td><td>0,65</td><td>250</td><td>20</td><td>0,61</td></tr>
<tr><td>13</td><td rowspan="2">30</td><td>3D</td><td>0,50</td><td>150</td><td>15,0</td><td>1,33</td><td>1,00</td><td>150</td><td>14,0</td><td>0,67</td><td>1,00</td><td>380</td><td>37</td><td>0,26</td></tr>
<tr><td>14</td><td>свыше 3D</td><td>0,40</td><td>100</td><td>10,0</td><td>2,38</td><td>0,80</td><td>100</td><td>9,5</td><td>1,25</td><td>0,75</td><td>200</td><td>19</td><td>0,66</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td colspan="3"></td><td>б</td><td colspan="3"></td><td>в</td></tr>
</table>



```text
┌─────────────────────────────────────────────────────────────────┬───────────────────────────────┐
│Основное время на 100 мм расчетной длины                         │Горизонтально-расточные станки │
│Сверление отверстий                                              ├───────────────────────────────┤
│Сталь, чугун, медные сплавы и алюминиевые                        │Сверла спиральные из стали Р6М5│
│Среднесерийное производство                                      ├────────────────────┬──────────┤
│                                                                 │     Карта 121      │  Лист 2  │
├─────────────────────────────────────────────────────────────────┴────────────────────┴──────────┤
│   Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:   │
├──────────────────────────┬─────────────────┬─────────────────────────┬──────────────────────────┤
│Группы стали и предела    │Группа стали     │Углеродистые, хромистые, │     Марганцовистые,      │
│прочности                 │                 │никелевые, хромоникелевые│   хромомарганцовистые,   │
│                          │                 │                         │   хромомолибденовые и    │
│                          │                 │                         │      близкие к ним       │
│                          ├─────────────────┼───────┬───────────┬─────┼───────┬────────────┬─────┤
│                          │Предел прочности │до 0,59│0,59 - 0,74│свыше│до 0,59│0,59 - 0,74 │свыше│
│                          │                 │       │           │0,74 │       │            │0,74 │
│                          ├─────────────────┼───────┼───────────┼─────┼───────┼────────────┼─────┤
│                          │                 │       │┌───┐      │     │       │            │     │
│                          │Коэффициент      │0,8    ││1,0│      │1,25 │1,1    │1,2         │1,35 │
│                          │                 │       │└───┘      │     │       │            │     │
├──────────────────────────┼─────────────────┼───────┴────┬──────┴─────┼───────┴────────────┴─────┤
│Твердости чугуна          │Твердость чугуна │до 1,76     │1,76 - 2,15 │свыше 2,15                │
│                          │НВ, ГПа          │            │            │                          │
│                          ├─────────────────┼────────────┼────────────┼──────────────────────────┤
│                          │                 │            │┌───┐       │                          │
│                          │Коэффициент      │0,8         ││1,0│       │1,25                      │
│                          │                 │            │└───┘       │                          │
├──────────────────────────┼─────────────────┼────────────┴────────────┼──────────────────────────┤
│Группы медных сплавов и   │Группа сплавов   │        Гомогенные       │Гетерогенные              │
│твердости                 ├─────────────────┼────────────┬────────────┼──────────────────────────┤
│                          │Твердость НВ, ГПа│0,59 - 0,74 │0,98 - 1,37 │1,47 - 2,15               │
│                          ├─────────────────┼────────────┼────────────┼──────────────────────────┤
│                          │                 │            │┌───┐       │                          │
│                          │Коэффициент      │0,55        ││1,0│       │1,25                      │
│                          │                 │            │└───┘       │                          │
├──────────────────────────┼─────────────────┼────────────┴────────────┼──────────────────────────┤
│Группы алюминиевых сплавов│Группа сплавов   │Силумин и литейные сплавы│Дюралюминий               │
│и твердости               ├─────────────────┼─────────────────────────┼──────────────────────────┤
│                          │Твердость НВ, ГПа│до 0,64                  │до 0,98                   │
│                          ├─────────────────┼─────────────────────────┼──────────────────────────┤
│                          │Коэффициент      │0,75                     │0,7                       │
├──────────────────────────┼─────────────────┼─────────────────────────┼──────────────────────────┤
│Жесткости детали или      │Жесткость детали │Деталь и установка       │Деталь неустойчивая       │
│крепления                 │                 │жесткие                  │                          │
│                          ├─────────────────┼─────────────────────────┼──────────────────────────┤
│                          │                 │┌───┐                    │                          │
│                          │Коэффициент      ││1,0│                    │1,1                       │
│                          │                 │└───┘                    │                          │
├──────────────────────────┼─────────────────┼─────────────────────────┼──────────────────────────┤
│Характера обработки       │Характер         │Под зенкерование и       │Под развертывание и       │
│                          │обработки        │расточку резцом          │нарезание резьбы метчиком │
│                          ├─────────────────┼─────────────────────────┼──────────────────────────┤
│                          │                 │┌───┐                    │                          │
│                          │Коэффициент      ││1,0│                    │1,3                       │
│                          │                 │└───┘                    │                          │
└──────────────────────────┴─────────────────┴─────────────────────────┴──────────────────────────┘
```



<table>
<colgroup><col width="8%"><col width="5%"><col width="5%"><col width="11%"><col width="8%"><col width="3%"><col width="4%"><col width="3%"><col width="3%"><col width="4%"><col width="3%"><col width="5%"><col width="3%"><col width="7%"><col width="4%"><col width="7%"><col width="7%"><col width="3%"><col width="8%"></colgroup>
<tr><td colspan="11">Основное время на 100 мм расчетной длины Рассверливание отверстий</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="11" rowspan="2">Чугун серый, НВ = 1,76 - 2,15 ГПа Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Среднесерийное производство</td><td colspan="8">Сверла спиральные из стали Р6М5</td></tr>
<tr><td colspan="8">Карта 122</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td rowspan="3">Диаметр предварительно обрабатываемого отверстия d, мм</td><td colspan="6">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="3" rowspan="3">t , о 100 мин.</td><td colspan="4">Сталь конструкционная углеродистая, сигма = в 0,59 - 0,74 ГПа</td><td colspan="2" rowspan="3">t , о 100 мин.</td></tr>
<tr><td colspan="6">Режимы резания</td><td colspan="4">Режимы резания</td></tr>
<tr><td colspan="2">S , о мм/мин.</td><td colspan="2">n, об./ мин.</td><td colspan="2">v, м/ мин.</td><td colspan="2">S , о мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>1</td><td colspan="2" rowspan="2">25</td><td>10</td><td colspan="2">1,0</td><td colspan="2" rowspan="2">250</td><td colspan="2" rowspan="2">19,5</td><td colspan="3">0,40</td><td colspan="2">0,9</td><td>160</td><td>12,5</td><td colspan="2">0,69</td></tr>
<tr><td>2</td><td>15</td><td colspan="2">1,1</td><td colspan="3">0,36</td><td colspan="2">1,0</td><td>200</td><td>15,5</td><td colspan="2">0,50</td></tr>
<tr><td>3</td><td colspan="2" rowspan="3">30</td><td>10</td><td colspan="2">1,0</td><td colspan="2" rowspan="2">200</td><td colspan="2" rowspan="2">19,0</td><td colspan="3">0,50</td><td colspan="2">0,9</td><td>125</td><td>12,0</td><td colspan="2">0,89</td></tr>
<tr><td>4</td><td>15</td><td colspan="2">1,1</td><td colspan="3">0,45</td><td colspan="2">0,9</td><td>160</td><td rowspan="2">15,0</td><td colspan="2">0,70</td></tr>
<tr><td>5</td><td>20</td><td colspan="2">1,2</td><td colspan="2">225</td><td colspan="2">21,0</td><td colspan="3">0,37</td><td colspan="2">1,0</td><td>160</td><td colspan="2">0,62</td></tr>
<tr><td>6</td><td colspan="2" rowspan="3">40</td><td>15</td><td colspan="2">1,0</td><td colspan="2">150</td><td colspan="2">18,5</td><td colspan="3">0,67</td><td colspan="2">1,0</td><td>100</td><td>12,5</td><td colspan="2">1,00</td></tr>
<tr><td>7</td><td>20</td><td colspan="2">1,1</td><td colspan="2">160</td><td colspan="2">20,0</td><td colspan="3">0,57</td><td colspan="2">1,0</td><td rowspan="2">120</td><td rowspan="2">15,0</td><td colspan="2">0,83</td></tr>
<tr><td>8</td><td>30</td><td colspan="2">1,2</td><td colspan="2">175</td><td colspan="2">22,0</td><td colspan="3">0,47</td><td colspan="2">1,1</td><td colspan="2">0,76</td></tr>
<tr><td>9</td><td colspan="2" rowspan="3">50</td><td>20</td><td colspan="2">1,1</td><td colspan="2" rowspan="2">115</td><td colspan="2" rowspan="2">18,0</td><td colspan="3">0,79</td><td colspan="2">1,0</td><td>75</td><td>12,0</td><td colspan="2">1,33</td></tr>
<tr><td>10</td><td>30</td><td colspan="2">1,3</td><td colspan="3">0,67</td><td colspan="2">1,0</td><td rowspan="2">90</td><td rowspan="2">14,0</td><td colspan="2">1,10</td></tr>
<tr><td>11</td><td>40</td><td colspan="2">1,3</td><td colspan="2">125</td><td colspan="2">19,5</td><td colspan="3">0,71</td><td colspan="2">1,2</td><td colspan="2">0,93</td></tr>
<tr><td>12</td><td colspan="2" rowspan="3">60</td><td>30</td><td colspan="2">1,2</td><td colspan="2">90</td><td colspan="2">17,5</td><td colspan="3">0,93</td><td colspan="2">1,0</td><td>60</td><td>11,5</td><td colspan="2">1,67</td></tr>
<tr><td>13</td><td>40</td><td colspan="2">1,2</td><td colspan="2"></td><td colspan="2"></td><td colspan="3">0,83</td><td colspan="2">1,0</td><td rowspan="2">70</td><td rowspan="2">13,0</td><td colspan="2">1,42</td></tr>
<tr><td>14</td><td>50</td><td colspan="2">1,4</td><td colspan="2">100</td><td colspan="2">19,5</td><td colspan="3">0,71</td><td colspan="2">1,2</td><td colspan="2">1,20</td></tr>
<tr><td colspan="10">Индекс</td><td colspan="3">а</td><td colspan="4"></td><td colspan="2">б</td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="4">Твердости чугуна</td><td colspan="3">Твердость чугуна НВ, ГПа</td><td colspan="9">до 1,76 1,76 - 2,15</td><td colspan="5">свыше 2,15</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="9"></td><td colspan="5" rowspan="3">1,25</td></tr>
<tr><td colspan="6">0,8</td><td>1,0</td><td colspan="2"></td></tr>
<tr><td colspan="9"></td></tr>
<tr><td colspan="2" rowspan="5">Группы стали и предела прочности</td><td colspan="3">Группа стали</td><td colspan="9">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="5">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="4">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="2">свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="4" rowspan="3">0,8</td><td colspan="3"></td><td colspan="2" rowspan="3">1,25</td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td colspan="2">1,0</td><td></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="2" rowspan="4">Жесткость детали или крепления</td><td colspan="3">Жесткость детали</td><td colspan="9">Деталь и установка жесткие</td><td colspan="5">Деталь неустойчивая или тонкостенная</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="9"></td><td colspan="5" rowspan="3">1,1</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7"></td></tr>
<tr><td colspan="9"></td></tr>
<tr><td colspan="2" rowspan="4">Характера обработки</td><td colspan="3">Обработка</td><td colspan="9">Под зенкерование и расточку резцом</td><td colspan="5">Под развертывание и нарезание резьбы метчиком</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="9"></td><td colspan="5" rowspan="3">1,3</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7"></td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="5%"><col width="5%"><col width="11%"><col width="8%"><col width="3%"><col width="4%"><col width="3%"><col width="3%"><col width="4%"><col width="3%"><col width="4%"><col width="4%"><col width="7%"><col width="4%"><col width="7%"><col width="7%"><col width="3%"><col width="8%"></colgroup>
<tr><td colspan="11">Основное время на 100 мм расчетной длины Зенкерование отверстий</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="11" rowspan="2">Чугун, сталь Среднесерийное производство</td><td colspan="8">Зенкеры из стали Р6М5</td></tr>
<tr><td colspan="8">Карта 123</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td rowspan="3">Глубина резания t, мм, до</td><td colspan="6">Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="3" rowspan="3">t , о 100 мин.</td><td colspan="4">Сталь конструкционная углеродистая, сигма = в 0,59 - 0,74 ГПа</td><td colspan="2" rowspan="3">t , о 100 мин.</td></tr>
<tr><td colspan="6">Режимы резания</td><td colspan="4">Режимы резания</td></tr>
<tr><td colspan="2">S , о мм/мин.</td><td colspan="2">n, об./ мин.</td><td colspan="2">v, м/ мин.</td><td colspan="2">S , о мм/мин.</td><td>n, об./ мин.</td><td>v, м/ мин.</td></tr>
<tr><td>1</td><td colspan="2">15</td><td rowspan="9">1 - 2</td><td colspan="2">0,80</td><td colspan="2">400</td><td colspan="2">19,0</td><td colspan="3">0,31</td><td colspan="2">0,50</td><td>300</td><td>14,0</td><td colspan="2">0,67</td></tr>
<tr><td>2</td><td colspan="2">20</td><td colspan="2">1,00</td><td colspan="2">300</td><td colspan="2">20,5</td><td colspan="3">0,32</td><td colspan="2">0,65</td><td>215</td><td>13,5</td><td colspan="2">0,72</td></tr>
<tr><td>3</td><td colspan="2">25</td><td colspan="2">1,10</td><td colspan="2">230</td><td colspan="2">19,5</td><td colspan="3">0,36</td><td colspan="2">0,80</td><td>150</td><td>11,5</td><td colspan="2">0,83</td></tr>
<tr><td>4</td><td colspan="2">30</td><td colspan="2">1,20</td><td colspan="2">200</td><td colspan="2">18,5</td><td colspan="3">0,43</td><td colspan="2">0,90</td><td>120</td><td>11,5</td><td colspan="2">0,92</td></tr>
<tr><td>5</td><td colspan="2">35</td><td colspan="2">1,35</td><td colspan="2">160</td><td colspan="2">17,5</td><td colspan="3">0,46</td><td colspan="2">1,00</td><td>100</td><td>11,0</td><td colspan="2">1,00</td></tr>
<tr><td>6</td><td colspan="2">40</td><td colspan="2">1,50</td><td colspan="2">125</td><td colspan="2">15,5</td><td colspan="3">0,53</td><td colspan="2">1,05</td><td>75,0</td><td>9,3</td><td colspan="2">1,27</td></tr>
<tr><td>7</td><td colspan="2">50</td><td colspan="2">1,80</td><td colspan="2">100</td><td colspan="2">15,5</td><td colspan="3">0,56</td><td colspan="2">1,15</td><td>60,0</td><td>9,5</td><td colspan="2">1,45</td></tr>
<tr><td>8</td><td colspan="2">60</td><td colspan="2">2,00</td><td colspan="2">75</td><td colspan="2">14,0</td><td colspan="3">0,67</td><td colspan="2">1,20</td><td>47,5</td><td>9,0</td><td colspan="2">1,75</td></tr>
<tr><td>9</td><td colspan="2">80</td><td colspan="2">2,20</td><td colspan="2">50</td><td colspan="2">12,5</td><td colspan="3">0,91</td><td colspan="2">1,35</td><td>31,5</td><td>8</td><td colspan="2">2,35</td></tr>
<tr><td colspan="10">Индекс</td><td colspan="3">а</td><td colspan="4"></td><td colspan="2">б</td></tr>
<tr><td colspan="19">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="4">Твердости чугуна</td><td colspan="3">Твердость чугуна НВ, ГПа</td><td colspan="9">до 1,76 1,76 - 2,15</td><td colspan="5">свыше 2,15</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="9"></td><td colspan="5" rowspan="3">1,25</td></tr>
<tr><td colspan="6">0,8</td><td colspan="3">1,0</td></tr>
<tr><td colspan="9"></td></tr>
<tr><td colspan="2" rowspan="5">Группы стали и предела прочности</td><td colspan="3">Группа стали</td><td colspan="9">Углеродистые, хромистые, никелевые, хромоникелевые</td><td colspan="5">Марганцовистые, хромомарганцовистые, хромомолибденовые и близкие к ним</td></tr>
<tr><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="4">до 0,59</td><td colspan="3">0,59 - 0,74</td><td colspan="2">свыше 0,74</td><td colspan="2">до 0,59</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="4" rowspan="3">0,8</td><td colspan="3"></td><td colspan="2" rowspan="3">1,25</td><td colspan="2" rowspan="3">1,1</td><td colspan="2" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td colspan="2">1,0</td><td></td></tr>
<tr><td colspan="3"></td></tr>
<tr><td colspan="2" rowspan="4">Жесткости детали или крепления</td><td colspan="3">Жесткость детали</td><td colspan="9">Деталь и установка жесткие</td><td colspan="5">Деталь неустойчивая или тонкостенная</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="9"></td><td colspan="5" rowspan="3">1,1</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7"></td></tr>
<tr><td colspan="9"></td></tr>
<tr><td colspan="2" rowspan="4">Характера обработки</td><td colspan="3">Обработка</td><td colspan="9">Под чистое зенкерование и расточку резцом</td><td colspan="5">Под развертывание и нарезание резьбы метчиком</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="9"></td><td colspan="5" rowspan="3">1,3</td></tr>
<tr><td colspan="2">1,0</td><td colspan="7"></td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="8%"><col width="3%"><col width="9%"><col width="7%"><col width="7%"><col width="11%"><col width="4%"><col width="3%"><col width="3%"><col width="7%"><col width="7%"><col width="4%"><col width="3%"><col width="11%"><col width="7%"></colgroup>
<tr><td colspan="8" rowspan="2">Основное время на 100 мм расчетной длины Развертывание отверстий, Rz 20 - Rz 2,5, 1Т9 - 1Т8 квалитет, Ra 1,25, 1Т7 квалитет Чугун серый, НВ = 1,76 - 2,15 ГПа</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="8">Развертки из стали Р6М5</td></tr>
<tr><td colspan="8">Среднесерийное производство</td><td colspan="8">Карта 124</td></tr>
<tr><td rowspan="3">N позиции</td><td colspan="2" rowspan="3">Диаметр обрабатываемого отверстия D, мм, до</td><td colspan="3">1Т9 - 1Т8 квалитет. Обработка одной разверткой</td><td rowspan="3">t , о 100 мин.</td><td colspan="2" rowspan="3">N , р кВт, до</td><td colspan="5">1Т7 квалитет. Обработка двумя развертками</td><td rowspan="3">t , о 100 мин.</td><td rowspan="3">N , р кВт, до</td></tr>
<tr><td colspan="3">Режимы резания</td><td colspan="5">Режимы резания</td></tr>
<tr><td>S , о мм/об.</td><td>n, об./ мин.</td><td>v, м/ мин.</td><td colspan="2">S , о мм/об.</td><td>n, об./ мин.</td><td colspan="2">v, м/ мин.</td></tr>
<tr><td rowspan="2">1</td><td colspan="2" rowspan="2">10</td><td rowspan="2">1,7</td><td rowspan="2">230</td><td rowspan="2">7,2</td><td rowspan="2">0,25</td><td colspan="2" rowspan="20">1</td><td colspan="2">2,2</td><td>200</td><td colspan="2">6,3</td><td rowspan="2">0,51</td><td rowspan="20">1</td></tr>
<tr><td colspan="2">1,4</td><td>250</td><td colspan="2">7,8</td></tr>
<tr><td rowspan="2">2</td><td colspan="2" rowspan="2">15</td><td rowspan="2">1,9</td><td rowspan="2">150</td><td rowspan="2">7,0</td><td rowspan="2">0,35</td><td colspan="2">2,3</td><td>125</td><td colspan="2">5,9</td><td rowspan="2">0,75</td></tr>
<tr><td colspan="2">1,5</td><td>160</td><td colspan="2">7,5</td></tr>
<tr><td rowspan="2">3</td><td colspan="2" rowspan="2">20</td><td rowspan="2">2,0</td><td rowspan="2">100</td><td rowspan="2">6,3</td><td rowspan="2">0,50</td><td colspan="2">2,6</td><td>90</td><td colspan="2">5,7</td><td rowspan="2">1,00</td></tr>
<tr><td colspan="2">1,7</td><td>100</td><td colspan="2">6,3</td></tr>
<tr><td rowspan="2">4</td><td colspan="2" rowspan="2">25</td><td rowspan="2">2,2</td><td rowspan="2">80,0</td><td rowspan="2">6,2</td><td rowspan="2">0,57</td><td colspan="2">2,7</td><td>60</td><td colspan="2">4,7</td><td rowspan="2">1,28</td></tr>
<tr><td colspan="2">1,9</td><td>80</td><td colspan="2">6,2</td></tr>
<tr><td rowspan="2">5</td><td colspan="2" rowspan="2">30</td><td rowspan="2">2,4</td><td rowspan="2">60,0</td><td rowspan="2">5,6</td><td rowspan="2">0,69</td><td colspan="2">3,1</td><td>50</td><td colspan="2">4,6</td><td rowspan="2">1,48</td></tr>
<tr><td colspan="2">2,0</td><td>60</td><td colspan="2">5,6</td></tr>
<tr><td rowspan="2">6</td><td colspan="2" rowspan="2">35</td><td rowspan="2">2,6</td><td rowspan="2">48,0</td><td rowspan="2">5,3</td><td rowspan="2">0,80</td><td colspan="2">3,2</td><td>40</td><td colspan="2">4,4</td><td rowspan="2">1,78</td></tr>
<tr><td colspan="2">2,0</td><td>50</td><td colspan="2">5,5</td></tr>
<tr><td rowspan="2">7</td><td colspan="2" rowspan="2">40</td><td rowspan="2">2,7</td><td rowspan="2">38,0</td><td rowspan="2">4,8</td><td rowspan="2">0,97</td><td colspan="2">3,4</td><td>30</td><td colspan="2">4,0</td><td rowspan="2">2,11</td></tr>
<tr><td colspan="2">2,2</td><td>40</td><td colspan="2">5,0</td></tr>
<tr><td rowspan="2">8</td><td colspan="2" rowspan="2">50</td><td rowspan="2">2,9</td><td rowspan="2">30,0</td><td rowspan="2">4,7</td><td rowspan="2">1,15</td><td colspan="2">3,8</td><td>25</td><td colspan="2">3,9</td><td>2,30</td></tr>
<tr><td colspan="2">2,6</td><td>31</td><td colspan="2">4,9</td><td></td></tr>
<tr><td rowspan="2">9</td><td colspan="2" rowspan="2">60</td><td rowspan="2">3,2</td><td rowspan="2">25,0</td><td rowspan="2">4,7</td><td rowspan="2">1,25</td><td colspan="2">4,3</td><td>20</td><td colspan="2">3,8</td><td rowspan="2">2,54</td></tr>
<tr><td colspan="2">2,9</td><td>25</td><td colspan="2">4,7</td></tr>
<tr><td rowspan="2">10</td><td colspan="2" rowspan="2">80</td><td rowspan="2">4,1</td><td rowspan="2">164</td><td rowspan="2">4,1</td><td rowspan="2">1,48</td><td colspan="2">5,1</td><td>16</td><td colspan="2">4,0</td><td rowspan="2">2,85</td></tr>
<tr><td colspan="2">3,4</td><td>18</td><td colspan="2">4,5</td></tr>
<tr><td colspan="6">Индекс</td><td>а</td><td colspan="7"></td><td>б</td><td></td></tr>
<tr><td colspan="16">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="4">Твердости чугуна</td><td colspan="11">Твердость чугуна 1,76 1,76 - 2,15</td><td colspan="3">свыше 2,15</td></tr>
<tr><td colspan="11"></td><td colspan="3" rowspan="3">1,25</td></tr>
<tr><td colspan="8">Коэффициент 0,8</td><td colspan="3">1,0</td></tr>
</table>



<table>
<colgroup><col width="8%"><col width="11%"><col width="11%"><col width="9%"><col width="4%"><col width="5%"><col width="7%"><col width="4%"><col width="4%"><col width="7%"><col width="9%"><col width="3%"><col width="7%"><col width="3%"><col width="8%"></colgroup>
<tr><td colspan="7" rowspan="2">Основное время на 100 мм расчетной длины Развертывание отверстий, Rz 20 - Rz 2,5, 1Т9 - 1Т8 квалитет, Ra 1,25, 1Т7 квалитет</td><td colspan="8">Горизонтально-расточные станки</td></tr>
<tr><td colspan="8">Развертки из стали Р6М5</td></tr>
<tr><td colspan="7">Сталь конструкционная углеродистая, сигма = 0,59 - 0,74 ГПа в Среднесерийное производство</td><td colspan="8">Карта 125</td></tr>
<tr><td rowspan="3">N позиции</td><td rowspan="2">Диаметр обрабатываемого</td><td colspan="4">1Т9 - 1Т8 квалитет</td><td colspan="2">t , о 100</td><td colspan="5">1Т7 квалитет</td><td colspan="2">t , о 100</td></tr>
<tr><td colspan="4">Режимы резания</td><td colspan="2" rowspan="2">мин.</td><td colspan="5">Режимы резания</td><td colspan="2" rowspan="2">мин.</td></tr>
<tr><td>отверстия D, мм, до</td><td>S , о мм/об.</td><td>n, об./ мин.</td><td colspan="2">v, м/мин.</td><td colspan="2">S , о мм/об.</td><td>n, об./ мин.</td><td colspan="2">v, м/мин.</td></tr>
<tr><td rowspan="2">1</td><td rowspan="2">10</td><td rowspan="2">0,7</td><td rowspan="2">300</td><td colspan="2" rowspan="2">9,4</td><td colspan="2" rowspan="2">0,47</td><td colspan="2">0,8</td><td>300</td><td colspan="2">9,4</td><td colspan="2" rowspan="2">2,00</td></tr>
<tr><td colspan="2">0,5</td><td>125</td><td colspan="2">4,0</td></tr>
<tr><td rowspan="2">2</td><td rowspan="2">15</td><td rowspan="2">0,8</td><td rowspan="2">200</td><td colspan="2" rowspan="2">9,4</td><td colspan="2" rowspan="2">0,62</td><td colspan="2">0,9</td><td>200</td><td colspan="2">9,4</td><td colspan="2" rowspan="2">2,21</td></tr>
<tr><td colspan="2">0,6</td><td>100</td><td colspan="2">4,7</td></tr>
<tr><td rowspan="2">3</td><td rowspan="2">20</td><td rowspan="2">0,8</td><td rowspan="2">160</td><td colspan="2" rowspan="2">10</td><td colspan="2" rowspan="2">0,78</td><td colspan="2">1,0</td><td>160</td><td colspan="2">10</td><td colspan="2" rowspan="2">2,88</td></tr>
<tr><td colspan="2">0,7</td><td>63</td><td colspan="2">4,0</td></tr>
<tr><td rowspan="2">4</td><td rowspan="2">25</td><td rowspan="2">0,9</td><td rowspan="2">125</td><td colspan="2" rowspan="2">9,7</td><td colspan="2" rowspan="2">1,25</td><td colspan="2">1,1</td><td>125</td><td colspan="2">8,5</td><td colspan="2" rowspan="2">3,23</td></tr>
<tr><td colspan="2">0,8</td><td>50</td><td colspan="2">4,0</td></tr>
<tr><td rowspan="2">5</td><td rowspan="2">30</td><td rowspan="2">1,0</td><td rowspan="2">90,0</td><td colspan="2" rowspan="2">8,5</td><td colspan="2" rowspan="2">90</td><td colspan="2">1,2</td><td>90</td><td colspan="2">9,7</td><td colspan="2" rowspan="2">3,69</td></tr>
<tr><td colspan="2">0,9</td><td>40</td><td colspan="2">3,8</td></tr>
<tr><td rowspan="2">6</td><td rowspan="2">35</td><td rowspan="2">1,0</td><td rowspan="2">75,0</td><td colspan="2" rowspan="2">8,3</td><td colspan="2" rowspan="2">75</td><td colspan="2">1,3</td><td>75</td><td colspan="2">8,3</td><td colspan="2" rowspan="2">4,10</td></tr>
<tr><td colspan="2">0,9</td><td>36</td><td colspan="2">4,0</td></tr>
<tr><td rowspan="2">7</td><td rowspan="2">40</td><td rowspan="2">1,2</td><td rowspan="2">55,0</td><td colspan="2" rowspan="2">6,9</td><td colspan="2" rowspan="2">55</td><td colspan="2">1,4</td><td>55</td><td colspan="2">6,9</td><td colspan="2" rowspan="2">4,40</td></tr>
<tr><td colspan="2">1,0</td><td>32</td><td colspan="2">4,0</td></tr>
<tr><td rowspan="2">8</td><td rowspan="2">50</td><td rowspan="2">1,4</td><td rowspan="2">40,0</td><td colspan="2" rowspan="2">6,3</td><td colspan="2" rowspan="2">40</td><td colspan="2">1,5</td><td>40</td><td colspan="2">6,3</td><td colspan="2" rowspan="2">5,00</td></tr>
<tr><td colspan="2">1,2</td><td>25</td><td colspan="2">4,0</td></tr>
<tr><td rowspan="2">9</td><td rowspan="2">60</td><td rowspan="2">1,5</td><td rowspan="2">30,0</td><td colspan="2" rowspan="2">5,6</td><td colspan="2" rowspan="2">30</td><td colspan="2">1,7</td><td>30</td><td colspan="2">5,6</td><td colspan="2" rowspan="2">5,36</td></tr>
<tr><td colspan="2">1,4</td><td>21</td><td colspan="2">4,0</td></tr>
<tr><td rowspan="2">10</td><td rowspan="2">80</td><td rowspan="2">1,7</td><td rowspan="2">21,5</td><td colspan="2" rowspan="2">6,4</td><td colspan="2" rowspan="2">21,5</td><td colspan="2">2,0</td><td>21,5</td><td colspan="2">5,4</td><td colspan="2" rowspan="2">6,02</td></tr>
<tr><td colspan="2">1,5</td><td>18</td><td colspan="2">4,5</td></tr>
<tr><td colspan="6">Индекс</td><td colspan="2">а</td><td colspan="2"></td><td colspan="3"></td><td colspan="2">б</td></tr>
<tr><td colspan="15">Поправочные коэффициенты на время обработки для измененных условий работы в зависимости от:</td></tr>
<tr><td colspan="2" rowspan="5">Группы стали и предела прочности</td><td colspan="3">Группа стали</td><td colspan="10">Углеродистые, Марганцовистые, хромистые, хромомарганцовистые, никелевые, хромомолибденовые и хромоникелевые близкие к ним</td></tr>
<tr><td colspan="3">Предел прочности сигма , ГПа в</td><td colspan="4">до 0,59 0,59 - 0,74</td><td colspan="3">свыше до 0,59 0,74</td><td colspan="2">0,59 - 0,74</td><td>свыше 0,74</td></tr>
<tr><td colspan="3" rowspan="3">Коэффициент</td><td colspan="4"></td><td colspan="3" rowspan="3">1,25 1,1</td><td colspan="2" rowspan="3">1,2</td><td rowspan="3">1,35</td></tr>
<tr><td colspan="2">0,8</td><td colspan="2">1,0</td></tr>
</table>






<div align="right">

<a id="p103957"></a>Приложение 1

</div>



<table>
<colgroup><col width="12%"><col width="15%"><col width="11%"><col width="7%"><col width="15%"><col width="19%"><col width="11%"><col width="11%"></colgroup>
<tr><td colspan="8">МЕХАНИЧЕСКИЕ СВОЙСТВА ОСНОВНЫХ КОНСТРУКЦИОННЫХ УГЛЕРОДИСТЫХ И ЛЕГИРОВАННЫХ СТАЛЕЙ</td></tr>
<tr><td rowspan="3">Группа стали</td><td rowspan="3">Марка</td><td colspan="6">Механические свойства</td></tr>
<tr><td colspan="3">в состоянии поставки по ГОСТу</td><td colspan="3">после термической обработки</td></tr>
<tr><td>ГОСТ</td><td>Состояние</td><td>сигма или в НВ, ГПа</td><td>Типовая термическая обработка</td><td>сигма , в ГПа</td><td>НВ, ГПа</td></tr>
<tr><td rowspan="11">Углеродистая обыкновенного качества</td><td>Ст0</td><td rowspan="11">380-71</td><td rowspan="11">Г</td><td>Не менее 0,30</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>СТ1кп</td><td>0,30 - 0,49</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>Ст1пс Ст1сп</td><td>0,31 - 0,41</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>Ст2кп</td><td>0,32 - 0,41</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>Ст2пс Ст2сп</td><td>0,33 - 0,43</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>Ст3кп</td><td>0,36 - 0,46</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>Ст3пс Ст3сп</td><td>0,37 - 0,48</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>Ст4кп</td><td>0,40 - 0,51</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>Ст4пс Ст4сп</td><td>0,41 - 0,53</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>Ст5пс Ст5сп</td><td>0,49 - 0,62</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>Ст6пс Ст6сп</td><td>Не менее 0,59</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>Углеродистая</td><td>С5кп</td><td>1050-74</td><td>Г</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td rowspan="42">качественная</td><td>С8кп</td><td>1050-74</td><td>Г</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>С8пс</td><td>1050-74</td><td>Г</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>С8</td><td>1050-74</td><td>Г</td><td>НВ; 1,28</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10кп</td><td>1050-74</td><td>Г</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>10п</td><td>1050-74</td><td>Г</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td rowspan="3">10</td><td>1050-74</td><td>Г</td><td>1,40</td><td rowspan="3">Нормализация 910° - 930°</td><td rowspan="3">&gt;= 0,33</td><td rowspan="3">&lt;= 1,40</td></tr>
<tr><td rowspan="2">1051-73</td><td>Н</td><td>1,83</td></tr>
<tr><td>О</td><td>-</td></tr>
<tr><td>11кп</td><td>1050-74</td><td>Г</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15кп</td><td>1050-74</td><td>Г</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15пс</td><td>1050-74</td><td>Г</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td rowspan="3">15</td><td>1050-74</td><td>Г</td><td>1,46</td><td rowspan="3">Нормализация 910° - 930°</td><td rowspan="3">&gt;= 0,36</td><td rowspan="3">&lt;= 1,53</td></tr>
<tr><td>1051-73</td><td>Н</td><td>1,93</td></tr>
<tr><td></td><td>О</td><td>1,46</td></tr>
<tr><td rowspan="3">20</td><td>1050-74</td><td>Г</td><td>1,59</td><td rowspan="3">Нормализация 900° - 920°</td><td>-</td><td>-</td></tr>
<tr><td rowspan="2">1051-73</td><td>Н</td><td>2,02</td><td rowspan="2">&gt;= 0,40</td><td rowspan="2">1,34 - 1,71</td></tr>
<tr><td>О</td><td>1,67</td></tr>
<tr><td rowspan="3">25</td><td>1050-74</td><td>Г</td><td>1,67</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>1051-73</td><td>Н</td><td>2,13</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>1051-73</td><td>О</td><td>1,67</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td rowspan="3">30</td><td>1050-74</td><td>Г</td><td>1,75</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td rowspan="2">1051-73</td><td>Н</td><td>2,24</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>О</td><td>1,75</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td rowspan="3">35</td><td>1050-74</td><td>Г</td><td>2,02</td><td>Нормализация 860° - 880°</td><td>&gt;= 0,51</td><td>1,53 - 1,92</td></tr>
<tr><td rowspan="2">1051-73</td><td>Н</td><td>2,24</td><td rowspan="2">Закалка 880° Отпуск 600°</td><td rowspan="2">-</td><td rowspan="2">1,83</td></tr>
<tr><td>О</td><td>1,83</td></tr>
<tr><td rowspan="4">40</td><td>1050-74</td><td>Г</td><td>2,13</td><td>Нормализация 860° - 880°</td><td>&gt;= 0,56</td><td>1,53 - 2,03</td></tr>
<tr><td rowspan="3">1051-73</td><td>О</td><td>1,83</td><td>Закалка 840° - 880°</td><td>-</td><td>-</td></tr>
<tr><td>Н</td><td>2,36</td><td rowspan="2">Отпуск 550° - 620°</td><td rowspan="2">&gt;= 0,69</td><td rowspan="2">1,88 - 2,23</td></tr>
<tr><td>О</td><td>1,93</td></tr>
<tr><td rowspan="3">45</td><td>1050-74</td><td>Г</td><td>2,36</td><td rowspan="3">Нормализация 850° - 870° или отжиг 840° - 850°</td><td rowspan="3">&gt;= 0,59</td><td rowspan="3">1,67 - 2,12</td></tr>
<tr><td rowspan="2">1051-73</td><td>О</td><td>1,93</td></tr>
<tr><td>Н</td><td>2,36</td></tr>
<tr><td rowspan="4">50</td><td rowspan="2">1050-74</td><td>Г</td><td>2,36</td><td rowspan="2">Нормализация 840° - 860°</td><td rowspan="2">&gt;= 0,62</td><td rowspan="2">1,75 - 2,24</td></tr>
<tr><td>О</td><td>2,02</td></tr>
<tr><td rowspan="2">1051-73</td><td>Н</td><td>2,50</td><td>Закалка 840°</td><td rowspan="2">-</td><td rowspan="2">2,12</td></tr>
<tr><td>О</td><td>2,12</td><td>Отпуск 600°</td></tr>
<tr><td rowspan="2">55</td><td rowspan="2">1050-74</td><td>Г</td><td>2,50</td><td rowspan="2">Нормализация 810°</td><td rowspan="2">0,62</td><td rowspan="2">2,24</td></tr>
<tr><td>О</td><td>2,12</td></tr>
<tr><td rowspan="3">60</td><td rowspan="2">1050-74</td><td>Г</td><td>2,50</td><td rowspan="3">-</td><td rowspan="3">-</td><td rowspan="3">-</td></tr>
<tr><td>О</td><td>2,24</td></tr>
<tr><td>1050-74</td><td>О</td><td>2,24</td></tr>
<tr><td rowspan="16">Углеродистая качественная с повышенным содержанием марганца</td><td rowspan="3">15Г</td><td>4543-71</td><td>Г</td><td>1,59</td><td rowspan="3">Нормализация 920°</td><td rowspan="3">0,39</td><td rowspan="3">&lt;= 1,59</td></tr>
<tr><td rowspan="2">1051-73</td><td>Н</td><td>2,02</td></tr>
<tr><td>О</td><td>1,59</td></tr>
<tr><td>20Г</td><td>4543-71</td><td>Г</td><td>1,75</td><td>Нормализация 900°</td><td>0,42</td><td>&lt;= 1,75</td></tr>
<tr><td>25Г</td><td>4543-71</td><td>Г</td><td>1,93</td><td>Нормализация</td><td>0,49</td><td>1,93</td></tr>
<tr><td>30Г</td><td>4543-71</td><td>Г О</td><td>2,12 1,93</td><td>Нормализация 880°</td><td>0,54</td><td>1,93</td></tr>
<tr><td>35Г</td><td>4543-71</td><td>Г</td><td>2,02</td><td>Нормализация</td><td>-</td><td>-</td></tr>
<tr><td rowspan="2">40Г</td><td rowspan="2">4543-71</td><td>Г</td><td>2,24</td><td rowspan="2">Нормализация 860°</td><td rowspan="2">0,59</td><td>&lt;= 2,24</td></tr>
<tr><td>О</td><td>2,02</td><td>&lt;= 2,02</td></tr>
<tr><td rowspan="2">45Г</td><td rowspan="2">4543-71</td><td>Г</td><td>2,24</td><td rowspan="2">Нормализация</td><td rowspan="2">-</td><td rowspan="2">-</td></tr>
<tr><td>О</td><td>2,02</td></tr>
<tr><td rowspan="2">50Г</td><td rowspan="2">4543-71</td><td>Г</td><td>2,24</td><td rowspan="2">Нормализация 840°</td><td rowspan="2">0,63</td><td rowspan="2">2,24</td></tr>
<tr><td>О</td><td>2,12</td></tr>
<tr><td>10Г2</td><td>4543-71</td><td>Г</td><td>1,93</td><td>-</td><td>-</td><td>1,93</td></tr>
<tr><td>30Г2</td><td>4543-71</td><td>Г</td><td>2,02</td><td>-</td><td>-</td><td>2,02</td></tr>
<tr><td>40Г2</td><td>4543-71</td><td>Г</td><td>2,12</td><td>-</td><td>-</td><td>2,12</td></tr>
<tr><td rowspan="4">Автоматная</td><td>А12</td><td rowspan="4">1414-75</td><td rowspan="4">Х</td><td rowspan="2">1,64 - 2,13</td><td rowspan="4">-</td><td rowspan="4">-</td><td rowspan="4">-</td></tr>
<tr><td>А20</td></tr>
<tr><td>А30</td><td>1,71 - 2,19</td></tr>
<tr><td>А40Г</td><td>1,67 - 2,24</td></tr>
<tr><td rowspan="9">Хромомарганцевая</td><td>18ХГ</td><td>4543-71</td><td>ОП</td><td>1,83</td><td rowspan="2">Закалка 860°. Отпуск 600°</td><td>-</td><td>1,83</td></tr>
<tr><td>35ХГ2</td><td>4543-71</td><td>ОП</td><td>2,24</td><td>0,83</td><td>2,24</td></tr>
<tr><td>18ХГТ</td><td>4543-71</td><td>ОП</td><td>2,12</td><td>-</td><td>-</td><td>2,12</td></tr>
<tr><td>20ХГР</td><td>4543-71</td><td>ОП</td><td>1,93</td><td>-</td><td>-</td><td>1,93</td></tr>
<tr><td>27ХГР</td><td>4543-71</td><td>ОП</td><td>2,12</td><td>-</td><td>-</td><td>2,12</td></tr>
<tr><td>25ХГТ</td><td>4543-71</td><td>ОП</td><td>2,12</td><td>-</td><td>-</td><td>2,12</td></tr>
<tr><td>30ХГТ</td><td>4543-71</td><td>ОП</td><td>2,24</td><td>-</td><td>-</td><td>2,24</td></tr>
<tr><td>40ХГТР</td><td>4543-71</td><td>ОП</td><td>2,24</td><td>-</td><td>-</td><td>2,24</td></tr>
<tr><td>35ХГФ</td><td>4543-71</td><td>ОП</td><td>2,02</td><td>-</td><td>-</td><td>2,02</td></tr>
<tr><td rowspan="6">Хромокремнемарганцевая и хромокремнемарганцевоникелевая</td><td>20ХГСА</td><td>4543-71</td><td>ОП</td><td>2,02</td><td>Закалка 880°. Отпуск 500°</td><td>0,78</td><td>2,02</td></tr>
<tr><td>25ХГСА</td><td>4543-71</td><td>ОП</td><td>2,12</td><td>Закалка 880°. Отпуск 480°</td><td>1,08</td><td>2,12</td></tr>
<tr><td>30ХГС</td><td>4543-71</td><td>ОП</td><td>2,24</td><td>Закалка 880°. Отпуск 540°</td><td>1,08</td><td>2,24</td></tr>
<tr><td>30ГСА</td><td>4543-71</td><td>ОП</td><td>2,24</td><td>-</td><td>-</td><td>2,24</td></tr>
<tr><td>30ХГСН2А (30ХГСНА)</td><td>4543-71</td><td>ОП</td><td>2,50</td><td>-</td><td>-</td><td>2,50</td></tr>
<tr><td>35ХГСА</td><td>4543-71</td><td>ОП</td><td>2,36</td><td>Закалка 950°. Отпуск 700°</td><td>1,08</td><td>2,36</td></tr>
<tr><td rowspan="10">Хромоникелевая и хромоникелевая с бором</td><td>20ХН</td><td>4543-71</td><td>ОП</td><td>1,93</td><td>Закалка 860° - 810°. Отпуск 180°</td><td>0,78</td><td>1,93</td></tr>
<tr><td>40ХН</td><td>4543-71</td><td>ОП</td><td>2,02</td><td>Закалка 820° - 500°. Отпуск 500°</td><td>0,98</td><td>2,02</td></tr>
<tr><td>45ХН</td><td>4543-71</td><td>ОП</td><td>2,02</td><td>Отжиг 830° - 650°. Закалка 820°</td><td>-</td><td>2,02</td></tr>
<tr><td>50ХН</td><td>4543-71</td><td>ОП</td><td>2,02</td><td>Отпуск 530°. Отжиг 830° - 850°</td><td>1,03</td><td>2,02</td></tr>
<tr><td>12ХН2</td><td>4543-71</td><td>ОП</td><td>2,02</td><td>Закалка 760° - 810°. Отпуск 180°</td><td>0,78</td><td>2,02</td></tr>
<tr><td>12ХН3А</td><td>4543-71</td><td>ОП</td><td>2,12</td><td>-</td><td>-</td><td>2,12</td></tr>
<tr><td>20ХН3А</td><td>4543-71</td><td>ОП</td><td>2,50</td><td>-</td><td>-</td><td>2,50</td></tr>
<tr><td>12Х2НЧА</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>Закалка 760° - 810°. Отпуск 180°</td><td>0,93</td><td>2,63</td></tr>
<tr><td>20Х2НЧА</td><td>4543-71</td><td>ОП</td><td>2,63</td><td rowspan="2">Закалка 820°. Отпуск 530°</td><td rowspan="2">0,98</td><td rowspan="2">2,36</td></tr>
<tr><td>30ХН3А</td><td>4543-71</td><td>ОП</td><td>2,36</td></tr>
<tr><td rowspan="3">Хромомарганцевоникелевая и хромомарганцевоникелевая с титаном и бором</td><td>15ХГН2ТА (15ХГНТА)</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>-</td><td>-</td><td>2,63</td></tr>
<tr><td>20ХГНР</td><td>4543-71</td><td>ОП</td><td>1,93</td><td>-</td><td>-</td><td>1,93</td></tr>
<tr><td>38ХГН</td><td>4543-71</td><td>ОП</td><td>2,24</td><td>Закалка 850°. Отпуск 510°</td><td>0,88</td><td>2,24</td></tr>
<tr><td rowspan="9">Хромоникельмолибденовая</td><td>14Х2Н3М2</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>-</td><td>-</td><td>2,63</td></tr>
<tr><td>20ХН2М (20ХНМ)</td><td>4543-71</td><td>ОП</td><td>2,24</td><td>-</td><td>-</td><td>2,24</td></tr>
<tr><td>30ХН2МА (30ХНМ2)</td><td>4543-71</td><td>ОП</td><td>2,36</td><td>-</td><td>-</td><td>2,36</td></tr>
<tr><td>38Х2Н2МА (38ХНМА)</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>-</td><td></td><td>2,63</td></tr>
<tr><td>40ХН2МА (40ХНМА)</td><td>4543-71</td><td>ОП</td><td>2,50</td><td>Отжиг 840° - 830°. Закалка 850°. Отпуск 620°</td><td>1,08</td><td>2,63</td></tr>
<tr><td>40Х2Н2МА (40Х1НВА)</td><td>4543-71</td><td>ОП</td><td>2,50</td><td>-</td><td>-</td><td>2,50</td></tr>
<tr><td>38ХН3МА</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>-</td><td>-</td><td>2,63</td></tr>
<tr><td>18Х2НЧМА (18Х2НЧВА)</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>-</td><td>-</td><td>2,63</td></tr>
<tr><td>25Х2НЧМА (25Х2НЧВА)</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>-</td><td>-</td><td>2,63</td></tr>
<tr><td rowspan="5">Хромоникельмолибденованадиевая</td><td>30ХН2МФА</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>-</td><td>-</td><td>2,63</td></tr>
<tr><td>36Х2Н2МФА (36ХН1МФА)</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>-</td><td>-</td><td>2,63</td></tr>
<tr><td>38ХН3МФА</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>-</td><td>-</td><td>2,63</td></tr>
<tr><td>45ХН2МФА (45НМФА)</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>-</td><td>-</td><td>2,63</td></tr>
<tr><td>20ХНЧФА</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>-</td><td>-</td><td>2,63</td></tr>
<tr><td>Хромоалюминиевая и</td><td>38Х20 (38Х10)</td><td>4543-71</td><td>ОП</td><td>2,24</td><td>-</td><td>-</td><td>2,24</td></tr>
<tr><td>хромоалюминиевая с молибденом</td><td>38Х2МЮА (38Х2МЮА)</td><td>4543-71</td><td>ОП</td><td>2,63</td><td>Отжиг 930° - 960°</td><td>-</td><td>2,63</td></tr>
</table>


<a id="p104051"></a>Г - сталь горячекатаная, О - отожженная, Н - нагартованная холоднотянутая, Х - холоднотянутая, ОП - отожженная или отпущенная.





<div align="right">

<a id="p104052"></a>Приложение 2

</div>



<table>
<colgroup><col width="19%"><col width="31%"><col width="19%"><col width="31%"></colgroup>
<tr><td colspan="4">МЕХАНИЧЕСКИЕ СВОЙСТВА ЧУГУНА И МЕДНЫХ СПЛАВОВ</td></tr>
<tr><td colspan="2">Серый чугун (ГОСТ 1412-79)</td><td colspan="2">Ковкий чугун (ГОСТ 1215-79)</td></tr>
<tr><td>Марка отливки</td><td>Твердость по Бринеллю НВ, ГПа</td><td>Марка отливки</td><td>Твердость по Бринеллю НВ, ГПа</td></tr>
<tr><td>СЧ 10</td><td>1,40 - 2,24</td><td>КЧ 30-6</td><td>0,98 - 1,59</td></tr>
<tr><td>СЧ 15</td><td>1,59 - 2,24</td><td>КЧ 33-8</td><td>0,98 - 1,59</td></tr>
<tr><td>СЧ 18</td><td>1,66 - 2,24</td><td>КЧ 35-10</td><td>0,98 - 1,59</td></tr>
<tr><td>СЧ 20</td><td>1,66 - 2,36</td><td>КЧ 37-12</td><td>1,07 - 1,59</td></tr>
<tr><td>СЧ 21</td><td>1,66 - 2,36</td><td>КЧ 45-7</td><td>1,47 - 2,02</td></tr>
<tr><td>СЧ 24</td><td>1,66 - 2,36</td><td>КЧ 50-5</td><td>1,66 - 2,25</td></tr>
<tr><td>СЧ 25</td><td>1,76 - 2,45</td><td>КЧ 55-4</td><td>1,88 - 2,36</td></tr>
<tr><td>СЧ 30</td><td>1,77 - 2,49</td><td>КЧ 60-3</td><td>1,96 - 2,63</td></tr>
<tr><td>СЧ 35</td><td>1,93 - 2,63</td><td>КЧ 65-3</td><td>2,07 - 2,63</td></tr>
<tr><td>СЧ 40</td><td>2,02 - 2,79</td><td>КЧ 70-2</td><td>2,36 - 2,79</td></tr>
<tr><td>СЧ 45</td><td>2,24 - 2,83</td><td>КЧ 80-1,5</td><td>2,64 - 3,13</td></tr>
</table>


<a id="p104066"></a>*Примечание.* Перлитоферритный ковкий чугун (ПФ) в ГОСТ не входит.


<table>
<colgroup><col width="20%"><col width="15%"><col width="15%"><col width="18%"><col width="8%"><col width="24%"></colgroup>
<tr><td colspan="6">Медные сплавы (ГОСТ 17711-80, ГОСТ 613-79, ГОСТ 493-79, ГОСТ 5017-74)</td></tr>
<tr><td colspan="3">Группы</td><td colspan="2">Марки</td><td>НВ, ГПа</td></tr>
<tr><td rowspan="7">Гетерогенные</td><td colspan="2" rowspan="3">Высокой твердости</td><td colspan="2">БрА11Ж6Н6</td><td>2,45</td></tr>
<tr><td colspan="2">БрА10ЖУНЧЛ</td><td>1,66</td></tr>
<tr><td colspan="2">БрА10ЖЗМц2</td><td>1,17</td></tr>
<tr><td colspan="2" rowspan="4">Средней твердости</td><td colspan="2">БрА9ЖЗЛ</td><td>0,98</td></tr>
<tr><td colspan="2">БрА9Мц2Л</td><td>0,78</td></tr>
<tr><td colspan="2">ЛА 67-2,5</td><td>0,88</td></tr>
<tr><td colspan="2">БР.ОФ 6,5-0,15</td><td>0,78 - 0,88</td></tr>
<tr><td colspan="2" rowspan="4">Свинцовистые при основной гетерогенной структуре</td><td colspan="2">Бр03Ц12С5</td><td colspan="2">0,58</td></tr>
<tr><td colspan="2">Бр03Ц7С5Н1</td><td colspan="2">0,58</td></tr>
<tr><td colspan="2">ЛМцС58-2-2</td><td colspan="2">0,68 - 0,78</td></tr>
<tr><td colspan="2">ЛМц0С58-2-2-2</td><td colspan="2">0,88 - 0,98</td></tr>
<tr><td colspan="2">Гомогенные сплавы</td><td colspan="2">Бр.ОФ4-0,25</td><td colspan="2">0,68 - 0,88 ----------- 1,56 - 1,96</td></tr>
<tr><td colspan="2"></td><td colspan="2">Бр.0Ц4-3</td><td colspan="2">0,49 - 0,68 ----------- 1,47 - 1,66</td></tr>
<tr><td colspan="2">С содержанием свинца &lt; 10% при основной гомогенной структуре</td><td colspan="2">Бр0ЦС4-4-2,5</td><td colspan="2">0,49 - 0,68 ----------- 1,47 - 1,66</td></tr>
<tr><td colspan="2" rowspan="2">С содержанием свинца &gt; 15%</td><td colspan="2">Бр.ОЧЦ017</td><td colspan="2">0,58</td></tr>
<tr><td colspan="2">Бр.С30</td><td colspan="2">0,24</td></tr>
</table>


<a id="p104076"></a>*Примечание.* Для деформируемых бронз в числителе приведена твердость для мягкого состояния, в знаменателе - для твердого состояния.

<a id="p104077"></a><...>

<div align="right">

<a id="p104078"></a>Приложение 4

</div>


<div align="center">

<a id="p104079"></a>**ВСПОМОГАТЕЛЬНОЕ ВРЕМЯ,**<br>
**СВЯЗАННОЕ С РАСЧЕТОМ НЕПОЛНОГО ШТУЧНОГО ВРЕМЕНИ**

</div>


<a id="p104080"></a><...>


<table>
<colgroup><col width="5%"><col width="30%"><col width="20%"><col width="15%"><col width="30%"></colgroup>
<tr><td rowspan="5">N п/п</td><td colspan="2" rowspan="5">Характер обработки</td><td rowspan="5">Измеряемый размер, мм, до</td><td>Вид станков</td></tr>
<tr><td>Столиковые</td></tr>
<tr><td>Диаметр шпинделя, мм, до</td></tr>
<tr><td>110</td></tr>
<tr><td>Время на одну поверхность, мин.</td></tr>
<tr><td>22</td><td rowspan="5">Подрезка торцов пластиной (резцом)</td><td>без измерений</td><td>-</td><td>0,44</td></tr>
<tr><td>23</td><td rowspan="4">с измерением</td><td>100</td><td>0,55</td></tr>
<tr><td>24</td><td>500</td><td>0,65</td></tr>
<tr><td>25</td><td>1000</td><td>0,76</td></tr>
<tr><td>26</td><td>&gt; 1000</td><td>0,70</td></tr>
<tr><td>27</td><td rowspan="3">Снятие фасок</td><td>без измерений</td><td>-</td><td>0,44</td></tr>
<tr><td>28</td><td rowspan="2">с измерением</td><td>20</td><td>0,65</td></tr>
<tr><td>29</td><td>&gt; 20</td><td>0,76</td></tr>
<tr><td>30</td><td rowspan="3">Растачивание радиусов</td><td>без измерений</td><td>-</td><td>0,87</td></tr>
<tr><td>31</td><td rowspan="2">с измерением</td><td>40</td><td>1,86</td></tr>
<tr><td>32</td><td>&gt; 40</td><td>2,30</td></tr>
<tr><td>33</td><td>Прорезка канавок (с креплением</td><td>без измерений</td><td>-</td><td>1,20</td></tr>
<tr><td>34</td><td rowspan="2">инструмента в специальной оправке)</td><td rowspan="2">с измерением длины расположения размера</td><td>500</td><td>2,40</td></tr>
<tr><td>35</td><td>&gt; 500</td><td>2,60</td></tr>
<tr><td>36</td><td colspan="2">Нарезание резьбы метчиком (время на один метчик)</td><td>-</td><td>1,30</td></tr>
</table>






<div align="right">

<a id="p104097"></a>Приложение 5

</div>



<table>
<colgroup><col width="24%"><col width="15%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"><col width="7%"></colgroup>
<tr><td colspan="11">ВЕЛИЧИНА ВРЕЗАНИЯ И ПЕРЕБЕГА ИНСТРУМЕНТА</td></tr>
<tr><td colspan="11">Рисунок (не приводится)</td></tr>
<tr><td rowspan="3">Тип резцов</td><td>Угол резца фи в</td><td colspan="9">Глубина резания t, мм</td></tr>
<tr><td rowspan="2">плане, градус</td><td>1</td><td>2</td><td>4</td><td>6</td><td>8</td><td>10</td><td>12</td><td>16</td><td>20</td></tr>
<tr><td colspan="9">Величина врезания и перебега l , мм 1</td></tr>
<tr><td>Резцы проходные, подрезные и</td><td>45</td><td>2</td><td>3,5</td><td>6</td><td>8</td><td>11</td><td>13</td><td>15</td><td>18</td><td>24</td></tr>
<tr><td rowspan="3">расточные</td><td>60</td><td>2</td><td>2,5</td><td>4</td><td>5</td><td>7</td><td>8</td><td>9</td><td>11</td><td>16</td></tr>
<tr><td>75</td><td>2</td><td>2,5</td><td>3</td><td>4</td><td>5</td><td>6</td><td>6</td><td>7</td><td>10</td></tr>
<tr><td>90</td><td colspan="9">3 - 5</td></tr>
<tr><td>Резцы прорезные и отрезные</td><td>-</td><td colspan="9">2 - 5</td></tr>
</table>






<div align="right">

<a id="p104106"></a>Приложение 6

</div>



<table>
<colgroup><col width="15%"><col width="14%"><col width="5%"><col width="5%"><col width="4%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="5%"><col width="8%"></colgroup>
<tr><td colspan="15">ВЕЛИЧИНА ВРЕЗАНИЯ И ПЕРЕБЕГА ИНСТРУМЕНТА</td></tr>
<tr><td colspan="15">Рисунок (не приводится)</td></tr>
<tr><td colspan="5" rowspan="3">Характер обработки</td><td colspan="10">Диаметр инструмента, мм, до</td></tr>
<tr><td>3</td><td>5</td><td>10</td><td>15</td><td>20</td><td>25</td><td>30</td><td>40</td><td>50</td><td>60 и более</td></tr>
<tr><td colspan="10">Величина врезания и перебега l , мм 1</td></tr>
<tr><td colspan="5">Сверление на проход с одинарной сверлом заточкой</td><td>2</td><td>2,5</td><td>5</td><td>6</td><td>8</td><td>10</td><td>12</td><td>15</td><td>18</td><td>23</td></tr>
<tr><td colspan="5">с двойной заточкой</td><td>-</td><td>-</td><td>6</td><td>8</td><td>10</td><td>15</td><td>16</td><td>18</td><td>22</td><td>27</td></tr>
<tr><td colspan="5">Сверление в упор</td><td>1,5</td><td>2</td><td>4</td><td>6</td><td>7</td><td>9</td><td>11</td><td>14</td><td>17</td><td>21</td></tr>
<tr><td colspan="4" rowspan="5">Рассверливание при глубине резания t, мм, до</td><td>5</td><td>-</td><td>-</td><td>-</td><td>4</td><td>4</td><td>5</td><td>5</td><td>5</td><td>6</td><td>6</td></tr>
<tr><td>10</td><td>-</td><td>-</td><td>-</td><td>-</td><td>7</td><td>8</td><td>8</td><td>8</td><td>9</td><td>9</td></tr>
<tr><td>15</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>11</td><td>11</td><td>12</td><td>12</td></tr>
<tr><td>20</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>14</td><td>15</td><td>15</td></tr>
<tr><td>30</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>18</td><td>18</td></tr>
<tr><td rowspan="5">Зенкерование</td><td rowspan="4">На проход</td><td colspan="2">Глубина резания</td><td>1</td><td>-</td><td>-</td><td>-</td><td>3</td><td>3</td><td>3</td><td>4</td><td>4</td><td>5</td><td>5</td></tr>
<tr><td colspan="2" rowspan="3">t, мм, до</td><td>3</td><td>-</td><td>-</td><td>-</td><td>5</td><td>5</td><td>5</td><td>6</td><td>6</td><td>7</td><td>7</td></tr>
<tr><td>5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>7</td><td>7</td><td>8</td><td>8</td><td>9</td><td>9</td></tr>
<tr><td>10</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>12</td><td>13</td><td>13</td><td>14</td><td>15</td></tr>
<tr><td colspan="3">В упор</td><td>-</td><td>-</td><td>-</td><td>-</td><td>2</td><td>2</td><td>2</td><td>3</td><td>3</td><td>4</td><td>4</td></tr>
<tr><td colspan="3" rowspan="2">Развертывание цилиндрических отверстий</td><td colspan="2">на проход</td><td>-</td><td>8</td><td>9</td><td>15</td><td>18</td><td>19</td><td>19</td><td>24</td><td>25</td><td>26</td></tr>
<tr><td colspan="2">в упор</td><td>-</td><td>2</td><td>3</td><td>3</td><td>3</td><td>3</td><td>4</td><td>4</td><td>4</td><td>5</td></tr>
<tr><td colspan="5">Развертывание конических отверстий</td><td>1</td><td>1</td><td>1</td><td>1</td><td>1</td><td>1</td><td>1</td><td>1,5</td><td>1,5</td><td>1,5</td></tr>
<tr><td colspan="5">Центрование отверстий</td><td>1 - 2</td><td>2</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td colspan="5">Зенкование коническими зенковками</td><td>0,5</td><td>0,5</td><td>1</td><td>1</td><td>1</td><td>1</td><td>1</td><td>1,5</td><td>1,5</td><td>1,5</td></tr>
<tr><td colspan="5">Зенкование и цекование облицовочными инструментами</td><td>-</td><td>0,5</td><td>1</td><td>1</td><td>1</td><td>1</td><td>1</td><td>1,5</td><td>1,5</td><td>1,5</td></tr>
<tr><td colspan="5" rowspan="2">Нарезание резьбы машинными метчиками</td><td colspan="2">на проход</td><td colspan="8">длина заборной части (3 - 6) ниток + (1 - 2) калибрующие</td></tr>
<tr><td colspan="2">в упор</td><td colspan="8">(2,5 - 3) S</td></tr>
</table>






<div align="right">

<a id="p104131"></a>Приложение 7

</div>



<table>
<colgroup><col width="9%"><col width="11%"><col width="5%"><col width="5%"><col width="5%"><col width="6%"><col width="5%"><col width="2%"><col width="3%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="6%"><col width="5%"><col width="5%"></colgroup>
<tr><td colspan="8">ВЕЛИЧИНА ВРЕЗАНИЯ И ПЕРЕБЕГА ИНСТРУМЕНТА</td><td colspan="10">Фрезы торцевые, концевые</td></tr>
<tr><td colspan="18">Схема установки фрезы 1. Симметричная 2. Смещенная Рисунок Рисунок (не приводится) (не приводится)</td></tr>
<tr><td>Установка</td><td rowspan="2">Ширина фрезерования или ширина</td><td colspan="16">Диаметр фрезы, D, мм</td></tr>
<tr><td rowspan="2">фрезы</td><td>16</td><td>20</td><td>25</td><td>32</td><td>40</td><td colspan="2">50</td><td>63</td><td>80</td><td>100</td><td>125</td><td>160</td><td>200</td><td>250</td><td>320</td><td>400</td></tr>
<tr><td>паза В, мм</td><td colspan="16">Величина врезания и перебега l , мм 1</td></tr>
<tr><td rowspan="21">Симметричная</td><td>10</td><td>3,0</td><td>2,5</td><td>2,5</td><td>2,5</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>15</td><td>-</td><td>4,5</td><td>4,0</td><td>3,5</td><td>3,5</td><td colspan="2">3,5</td><td>3,5</td><td>3,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>20</td><td>-</td><td>-</td><td>6,3</td><td>5,0</td><td>4,5</td><td colspan="2">4,0</td><td>4,0</td><td>4,0</td><td>4,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>25</td><td>-</td><td>-</td><td>-</td><td>7,5</td><td>6,0</td><td colspan="2">5,0</td><td>5,0</td><td>5,0</td><td>5,0</td><td>5,0</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>30</td><td>-</td><td>-</td><td>-</td><td>12,0</td><td>8,5</td><td colspan="2">7,0</td><td>6,5</td><td>5,5</td><td>5,5</td><td>5,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>40</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">12,0</td><td>10,0</td><td>8,0</td><td>7,5</td><td>6,5</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td></tr>
<tr><td>60</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>25,0</td><td>13,0</td><td>13,0</td><td>11,0</td><td>9,5</td><td>8,5</td><td>7,5</td><td>-</td><td>-</td></tr>
<tr><td>80</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>23,0</td><td>23,0</td><td>18,0</td><td>15,0</td><td>13,0</td><td>11,0</td><td>10</td><td>-</td></tr>
<tr><td>100</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>29,0</td><td>21,0</td><td>18,0</td><td>15,0</td><td>13</td><td>12</td></tr>
<tr><td>120</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>49,0</td><td>31,0</td><td>24,0</td><td>20,0</td><td>17</td><td>14</td></tr>
<tr><td>140</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>44,0</td><td>33,0</td><td>33,0</td><td>27</td><td>24</td></tr>
<tr><td>160</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>44,0</td><td>33,0</td><td>27</td><td>24</td></tr>
<tr><td>180</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>61,0</td><td>43,0</td><td>33</td><td>26</td></tr>
<tr><td>200</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>54,0</td><td>40</td><td>32</td></tr>
<tr><td>220</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>70,0</td><td>49</td><td>38</td></tr>
<tr><td>240</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>94,0</td><td>61</td><td>45</td></tr>
<tr><td>260</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>72</td><td>53</td></tr>
<tr><td>280</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>88</td><td>62</td></tr>
<tr><td>300</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>109</td><td>73</td></tr>
<tr><td>320</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>85</td></tr>
<tr><td>340</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td>100</td></tr>
<tr><td rowspan="2">Смещенная</td><td>В &gt; 0,3D</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>33</td><td>42</td><td>52</td><td>65</td><td>80</td><td>103</td><td>124</td></tr>
<tr><td>В &lt; 0,3D</td><td>-</td><td>-</td><td>-</td><td>-</td><td>-</td><td colspan="2">-</td><td>-</td><td>-</td><td>31</td><td>38</td><td>48</td><td>60</td><td>74</td><td>94</td><td>117</td></tr>
</table>


<a id="p104158"></a>*Примечание.* При чистовой обработке в целях обеспечения чистой поверхности при выходе фрезы величину врезания и перебега следует брать, равной диаметру фрезы.






## <a id="p104159"></a>УСЛОВНЫЕ ОБОЗНАЧЕНИЯ



| Условные обозначения | Единицы измерения | Обозначаемые параметры и величины |
| --- | --- | --- |
|  |  | 1. Размеры обработки |
| D, d, диам. l | мм мм | Обрабатываемый диаметр Длина обрабатываемой поверхности |
| В h i t | мм мм мм мм | Ширина обрабатываемой поверхности Врезание и перебег Число проходов Глубина резания |
|  |  | 2. Время |
| Н вр | мин. | Норма времени |
| Т ш t о 100(10) t п.з t , t , н.ш н.ш | мин. мин. мин. мин. | Штучное время Основное время на 100(10) мм длины обрабатываемой поверхности Подготовительно-заключительное время Неполное штучное время на обработку поверхности |
| 1 2 t н.ш n t в.у t о t , t , t вп вп вп | мин. мин. мин. | Вспомогательное время на установку и снятие детали Основное время Вспомогательное время, связанное с переходом |
| 1 2 n в обс в отл | % % | Время на обслуживание рабочего места в % от оперативного времени Время на отдых и личные потребности в % от оперативного времени |
| К | - | Коэффициент на штучное время в зависимости от |
| Тш |  | размера партии обрабатываемых деталей в единичном и мелкосерийном производстве |
| К t.в Ч | - шт. | Коэффициент на вспомогательное время в зависимости от характера серийности работ в среднесерийном производстве Число деталей в партии |
|  |  | 3. Режимы резания |
| v | м/мин. | Скорость резания |
| S о | мм/об. | Подача |
| S м n | мм/мин. об./мин. | Подача стола или инструмента Частота вращения |
| N р | кВт | Мощность резания |
| N д | кВт | Мощность электродвигателя станка |
|  |  | 4. Характеристика обрабатываемого материала |
| сигма в | ГПа | Предел прочности обрабатываемого материала |
| НВ | ГПа | Твердость обрабатываемого материала по Бринеллю |
|  |  | 5. Характеристика и параметры режущего инструмента |
| фи альфа | градус градус | Главный угол в плане Задний угол |
| D, d, диам. z | мм - | Диаметр инструмента Число зубьев |
| ДП | - | Форма заточки двойная |
| Н, НП | - | Форма заточки нормальная |







## <a id="p104199"></a>ЛИТЕРАТУРА


<a id="p104200"></a>Общемашиностроительные [нормативы](https://bukva.ai/docs/obschemashinostroitelnye-normativy-rezhimov-goskomtrud-sssr-2) режимов резания для технического нормирования работ на металлорежущих станках. Часть 2. Зуборезные горизонтально-расточные, резьбонакатные и отрезные станки. М.: Машиностроение, 1974.
<a id="p104201"></a>Общемашиностроительные нормативы времени вспомогательного на обслуживание рабочего места и подготовительно-заключительного при работе на металлорежущих станках. Мелкосерийное и единичное производство. М.: Машиностроение, 1982.
<a id="p104202"></a>Изучение затрат рабочего времени и разработка нормативных материалов по труду. Методические рекомендации. М.: НИИ труда, 1966.
<a id="p104203"></a>Паспортные данные металлорежущих станков.



<a id="p104204"></a>

---