| A. | INFORMATION RELATING JOINTLY TO MOPEDS, MOTOR CYCLES, MOTOR TRICYCLES AND QUADRICYCLES |
| 0. | General |
| 0.1. | Make: ..................................................................................... |
| 0.2. | Type (state any possible variants and versions: each variant and each version must be identified by a code consisting of numbers or a combination of letters and numbers): ....................................................... |
| 0.2.1. | Commercial name (where applicable): ...................................... |
| 0.3. | Means of type identification if stated on vehicle b: ............... |
| 0.3.1. | Location of that means of identification: .................................... |
| 0.4. | Vehicle category c: ............................................................. |
| 0.5. | Name and address of manufacturer: ........................................... |
| 0.5.1. | Name(s) and addresse(s) of assembly plants: ............................. |
| 0.6. | Name and address of manufacturer's authorised representative, if any: ..................................................................................... |
| 0.7. | Location and method of affixing statutory inscriptions to the chassis: ................................................................................... |
| 0.7.1. | The serial numbering of the type begins with No: ................................................................................................ |
| 0.8. | Position and method of affixing the component type-approval mark for components and separate technical units: ............................................................................................... |
| 1. | General arrangement of the vehicle |
| 1.1. | Photos and/or drawings of a typical vehicle: .............................. |
| 1.2. | Dimensional drawing of the complete vehicle: ........................... |
| 1.2.1. | Wheelbase: ............................................................................. |
| 1.3. | Number of axles and wheels (where appropriate, number of crawler tracks or belts): ............................................................ |
| 1.4. | Position and arrangement of engine: .......................................... |
| 1.5. | Number of seating positions: .................................................... |
| 1.6. | Hand of drive - left or right <*> |
| 1.6.1. | Vehicle is equipped to be driven in right-hand or left-hand rule of the road traffic <*> |
| 2. | Masses (in kg) <**> |
| 2.0. | Unladen mass d, : ........................................................... |
| 2.1. | Mass of vehicle in running order : ........................................ |
| 2.1.1. | Distribution of that mass between the axles: .............................. |
| 2.2. | Mass of vehicle in running order , together with rider: ......... |
| 2.2.1. | Distribution of that mass between the axles: .............................. |
| 2.3. | Maximum technically permissible mass declared by the manufacturer: ........................................................................... |
| 2.3.1. | Division of that mass between the axles: .................................... |
| 2.3.2 | Maximum technically permissible mass on each of the axles: ................................................................................................ |
| 2.4. | Maximum hill-starting ability at the maximum technically permissible mass declared by the manufacturer: ........................................................... |
| 2.5. | Maximum towable mass (where applicable): ............................. |
| 2.6. | Maximum mass of the combination: .......................................... |
| 3. | Engine e |
| 3.0. | Manufacturer: .......................................................................... |
| 3.1. | Make: ...................................................................................... |
| 3.1.1. | Type (stated on the engine, or other means of identification): ................. |
| 3.1.2. | Location of engine number (if applicable): ................................. |
| 3.2. | Spark- or compression-ignition engine <*> |
| 3.2.1. | Specific characteristics of the engine |
| 3.2.1.1. | Operating cycle (four or two-stroke, spark or compression ignition) <*> |
| 3.2.1.2. | Number, arrangement and firing order of cylinders: ................... |
| 3.2.1.2.1. | Bore: ................................................................. mm f |
| 3.2.1.2.2. | Stroke: .............................................................. mm f |
| 3.2.1.3. | Cylinder capacity: ....................................................... $cm^{3}$ <g> |
| 3.2.1.4. | Compression ratio <**>: ......................................................... |
| 3.2.1.5. | Drawings of cylinder head, piston(s), piston rings and cylinder(s): .............................................................................. |
| 3.2.1.6. | Idling speed <**>: ..................................................... $min^{- 1}$ |
| 3.2.1.7. | Maximum net power output: .................. kW at ................. $min^{- 1}$ |
| 3.2.1.8. | Net maximum torque: ...................... Nm at ....................... $min^{- 1}$ |
| 3.2.2. | Fuel: diesel/petrol/mixture/LPG/other <*> |
| 3.2.3. | Fuel tank |
| 3.2.3.1. | Maximum capacity <**>: ........................................................ |
| 3.2.3.2. | Drawing of tank with indication of material used: ..................... |
| 3.2.3.3. | Diagram clearly indicating the position of the tank on the vehicle: .................... |
| 3.2.3.4. | Approval number of the fuel tank fitted: .................................... |
| 3.2.4. | Fuel supply |
| 3.2.4.1. | Via carburettor(s): yes/no <*> |
| 3.2.4.1.1. | Make(s): ................................................................................. |
| 3.2.4.1.2. | Type(s): ................................................................................. |
| 3.2.4.1.3. | Number fitted: ......................................................................... |
| 3.2.4.1.4. | Settings <**> |
| i.e. of |
| 3.2.4.1.4.1. | Diffusers: ................................................................................ |
| 3.2.4.1.4.2. | Level in float chamber: ............................................................. |
| 3.2.4.1.4.3. | Mass of float: ......................................................................... |
| 3.2.4.1.4.4. | Float needle: ............................................................................ |
| or |
| 3.2.4.1.4.5. | Fuel curve as a function of the air flow and setting required in order to maintain that curve: .................................................... |
| 3.2.4.1.5. | Cold-starting system: manual/automatic <*> |
| 3.2.4.1.5.1. | Operating principle(s): .............................................................. |
| 3.2.4.2. | By fuel injection (solely in the case of compression ignition): yes/no <*> |
| 3.2.4.2.1. | Description of system: ............................................................ |
| 3.2.4.2.2. | Operating principle: direct/indirect/turbulence chamber injection <*> |
| 3.2.4.2.3. | Injection pump
either: |
| 3.2.4.2.3.1. | Make(s): ................................................................................. |
| 3.2.4.2.3.2. | Type(s): .................................................................................. |
| or |
| 3.2.4.2.3.3. | Maximum fuel flow rate <**> ................................. $mm^{3}$ /per stroke or cycle <*> at a pump rotational speed of: ......................... $min^{- 1}$ or characteristic diagram: ............................................................................. |
| 3.2.4.2.3.4. | Injection advance <**>: ......................................................... |
| 3.2.4.2.3.5. | Injection advance curve <**>: ................................................. |
| 3.2.4.2.3.6. | Calibration procedure: test bench/engine <*> |
| 3.2.4.2.4. | Regulator |
| 3.2.4.2.4.1. | Type: ...................................................................................... |
| 3.2.4.2.4.2. | Cut-off point |
| 3.2.4.2.4.2.1. | Cut-off point under load: ................................................. $min^{- 1}$ |
| 3.2.4.2.4.2.2. | Cut-off point under no load: ............................................ $min^{- 1}$ |
| 3.2.4.2.4.3. | Idling speed: .................................................................. $min^{- 1}$ |
| 3.2.4.2.5. | Injection pipework |
| 3.2.4.2.5.1. | Length: ................................................................................ mm |
| 3.2.4.2.5.2. | Internal diameter: ............................................................... mm |
| 3.2.4.2.6. | Injector(s) |
| either |
| 3.2.4.2.6.1. | Make(s): .................................................................................. |
| 3.2.4.2.6.2. | Type(s): .................................................................................. |
| or |
| 3.2.4.2.6.3. | Opening pressure <**>: ................ kPa or characteristic diagram <**>: ............................... |
| 3.2.4.2.7. | Cold starting system (if applicable) |
| either: |
| 3.2.4.2.7.1. | Make(s): ................................................................................. |
| 3.2.4.2.7.2. | Type(s): .................................................................................. |
| or |
| 3.2.4.2.7.3. | Description: ............................................................................. |
| 3.2.4.2.8. | Secondary starting device (if applicable) |
| either: |
| 3.2.4.2.8.1. | Make(s): ................................................................................. |
| 3.2.4.2.8.2. | Type(s): .................................................................................. |
| or |
| 3.2.4.2.8.3. | Description of system: ............................................................. |
| 3.2.4.3. | By fuel injection (solely in the case of spark-ignition): yes/no <*> |
| either: |
| 3.2.4.3.1. | Description of system: ............................................................. |
| 3.2.4.3.2. | Operating principle: injection into induction manifold (single/multiple point) <*>/direct injection/other (state which) <*>: ....................................................................................... |
| or |
| 3.2.4.3.2.1. | Make(s) of the injection pump: ................................................ |
| 3.2.4.3.2.2. | Type(s) of the injection pump: .................................................. |
| 3.2.4.3.3. | Injectors: opening pressure <**>: ........................................ kPa |
| or characteristic diagram <**>: ............................................... |
| 3.2.4.3.4. | Injection advance: .................................................................... |
| 3.2.4.3.5. | Cold-starting system |
| 3.2.4.3.5.1. | Operating principle(s): ............................................................. |
| 3.2.4.3.5.2. | Operating/setting limits <*>, <**>: ........................................... |
| 3.2.4.4. | Fuel pump: yes/no <*> |
| 3.2.5. | Electrical equipment |
| 3.2.5.1. | Nominal voltage: .................... V, positive/negative earth <*> |
| 3.2.5.2. | Generator |
| 3.2.5.2.1. | Type: ...................................................................................... |
| 3.2.5.2.2. | Nominal power: ................................................................ W |
| 3.2.6. | Ignition |
| 3.2.6.1. | Make(s): .................................................................................. |
| 3.2.6.2. | Type(s): .................................................................................. |
| 3.2.6.3. | Operating principle: .................................................................. |
| 3.2.6.4. | Ignition advance curve or operating set point <**>: .................................... |
| 3.2.6.5. | Static timing <**>: .............................................. before TDC |
| 3.2.6.6. | Points gap <**>: .............................................................. mm |
| 3.2.6.7. | Dwell angle <**>: ....................................................... degrees |
| 3.2.6.8. | Anti-radio interference system: ................................................ |
| 3.2.6.8.1. | Terminology and drawing of anti-radio interference equipment: ...................................................................................... |
| 3.2.6.8.2. | Indication of the nominal DC resistance value and, in the case of resistive ignition leads, statement of nominal resistance per metre: ..................................................................................... |
| 3.2.7. | Cooling system (liquid/air) <*> |
| 3.2.7.1. | Nominal setting for the engine-temperature control device: ............................. |
| 3.2.7.2. | Liquid |
| 3.2.7.2.1. | Nature of liquid: ...................................................................... |
| 3.2.7.2.2. | Circulating pump(s): yes/no <*> |
| 3.2.7.3. | Air |
| 3.2.7.3.1. | Blower: yes/no <*> |
| 3.2.8. | Induction system |
| 3.2.8.1. | Supercharging: yes/no <*> |
| 3.2.8.1.1. | Make(s): ................................................................................. |
| 3.2.8.1.2. | Type(s): ................................................................................. |
| 3.2.8.1.3. | Description of system [example: maximum boost pressure .................... kPa, waste gate (where appropriate)] |
| 3.2.8.2. | Intercooler: with/without <*> |
| 3.2.8.3. | Description and drawings of induction pipework and accessories (plenum chamber, heating device, additional air intakes, etc.): .................................................................... |
| 3.2.8.3.1. | Description of induction manifold (with drawings and/or photos): ..................................................................... |
| 3.2.8.3.2. | Air filter, drawings: ................................................................. |
| or |
| 3.2.8.3.2.1. | Make(s): .................................................................................. |
| 3.2.8.3.2.2. | Type(s): .................................................................................. |
| 3.2.8.3.3. | Inlet silencer, drawings: ........................................................... |
| or |
| 3.2.8.3.3.1. | Make(s): .................................................................................. |
| 3.2.8.3.3.2. | Type(s): .................................................................................. |
| 3.2.9. | Exhaust system |
| 3.2.9.1. | Drawing of complete exhaust system: ......................................... |
| 3.2.10. | Minimum cross-section of the inlet and exhaust ports: ................................... |
| 3.2.11. | Induction system or equivalent data |
| 3.2.11.1. | Maximum valve lift, opening and closing angles in relation to the dead centres, or data concerning the settings of other possible systems: ....................................................................... |
| 3.2.11.2. | Reference and/or setting ranges <*>: ........................................ |
| (1)3.2.12. | Measures taken against air pollution |
| 3.2.12.1. | Device for recycling crankcase gases, solely in the case of four-stroke engines (description and drawings): |
| 3.2.12.2. | Additional anti-pollution devices (if any, and if not covered by another heading): |
| 3.2.12.2.1. | Catalytic converter: yes/no <*> |
| 3.2.12.2.1.1. | Number of catalytic converters and elements: |
| 3.2.12.2.1.2. | Dimensions, shape and volume of the catalytic converter(s): |
| 3.2.12.2.1.3. | Type of catalytic action: |
| 3.2.12.2.1.4. | Total charge of precious metal: |
| 3.2.12.2.1.5. | Relative concentration: |
| 3.2.12.2.1.6. | Substrate (structure and material): |
| 3.2.12.2.1.7. | Cell density: |
| 3.2.12.2.1.8. | Type of casing for the catalytic converter(s): |
| 3.2.12.2.1.9. | Location of the catalytic converter(s) (place and reference distance in the exhaust line): |
| 3.2.12.2.2. | Oxygen sensor: yes/no <*> |
| 3.2.12.2.2.1. | Type: |
| 3.2.12.2.2.2. | Location: |
| 3.2.12.2.2.3. | Control range: |
| 3.2.12.2.3. | Air injection: yes/no <*> |
| 3.2.12.2.3.1. | Type (pulse air, air pump etc.): |
| 3.2.12.2.4. | Exhaust gas recirculation: yes/no <*> |
| 3.2.12.2.4.1. | Characteristics (flow rate etc.): |
| 3.2.12.2.5. | Other systems (description and operation): |
| 3.2.13. | Location of the coefficient of absorption symbol (compression-ignition engines only): ......................................... |
| 3.3. | Electric traction motor |
| 3.3.1. | Type (winding, excitation): ....................................................... |
| 3.3.1.1. | Maximum continuous rated power <k>: .............................. kW |
| 3.3.1.2. | Operating voltage: .............................................................. V |
| 3.3.2. | Battery |
| 3.3.2.1. | Number of cells: ...................................................................... |
| 3.3.2.2. | Mass: ............................................................................. kg |
| 3.3.2.3. | Capacity: ...................................................... Ah (amp/hours) |
| 3.3.2.4. | Location: ................................................................................. |
| 3.4. | Other motors or combinations of motors (specific information concerning the parts of those motors): ....................................... |
| 3.5. | Cooling system temperatures permitted by the manufacturer |
| 3.5.1. | Liquid cooling |
| 3.5.1.1. | Maximum temperature at outlet: .......................................... °C |
| 3.5.2. | Air cooling |
| 3.5.2.1. | Reference point: ...................................................................... |
| 3.5.2.2. | Maximum temperature at reference point: .......................... °C |
| 3.6. | Lubrication system |
| 3.6.1. | Description of system: ............................................................. |
| 3.6.1.1. | Location of oil reservoir (if any): .............................................. |
| 3.6.1.2. | Feed system (pump/injection into induction system/mixed with the fuel, etc.) <*>: .................................................................. |
| 3.6.2. | Lubricant mixed with the fuel |
| 3.6.2.1. | Percentage: .............................................................................. |
| 3.6.3. | Oil cooler: yes/no <*> |
| 3.6.3.1. | Drawing(s): .............................................................................. |
| or |
| 3.6.3.1.1. | Make(s): ................................................................................. |
| 3.6.3.1.2. | Type(s): .................................................................................. |
| 4. | Transmission <h> |
| 4.1. | Diagram of transmission system: .............................................. |
| 4.2. | Type (mechanical, hydraulic, electrical, etc.): ............................ |
| 4.3. | Clutch (type): .......................................................................... |
| 4.4. | Gearbox |
| 4.4.1. | Type: automatic/manual <*> |
| 4.4.2. | Method of selection: by hand/foot <*> |
| 4.5. | Gear ratios |
| N | R1 | R2 | R3 | Rt |
| Minimum continuously variable transmission | | | | |
| 1 | | | | |
| 2 | | | | |
| 3 | | | | |
| ... | | | | |
| Maximum continuously variable transmission | | | | |
| Reverse gear | | | | |
N = gear ratio.
R1 = primary ratio (ratio of engine speed to rotational speed of primary gearbox shaft).
R2 = secondary ratio (ratio of rotational speed of primary shaft to rotational speed of secondary shaft in gearbox).
R3 = final drive ratio (ratio of rotational speed of gearbox output shaft to rotational speed of driven wheels).
Rt = overall ratio |
| 4.5.1. | Brief description of the electrical and/or electronic components used in the transmission: .......................................................... |
| 4.6. | Maximum speed of vehicle and gear in which it is reached (in km/h) : .............................................................................. |
| 4.7. | Speedometer |
| 4.7.1. | Make(s): .................................................................................. |
| 4.7.2. | Tvpe(s): ................................................................................. |
| 4.7.3. | Photographs and/or drawings of the complete system |
| 4.7.4. | Speed range displayed: ............................................................ |
| 4.7.5. | Tolerance of the measuring mechanism of the speedometer: ...... |
| 4.7.6. | Technical constant of the speedometer: ..................................... |
| 4.7.7. | Method of operation and description of the drive mechanism .... |
| 4.7.8. | Overall transmission ratio of the drive mechanism: ................... |
| 5. | Suspension |
| 5.1. | Drawing of suspension arranpement: ........................................ |
| 5.1.1. | Brief description of the electrical and/or electronic components used in the suspension: ........................................................... |
| 5.2. | Tyres (category, dimensions and maximum loading) and rims (standard type): ....................................................................... |
| 5.2.1. | Nominal rolling circumference: ................................................. |
| 5.2.2. | Tyre pressures recommended by the manufacturer: ............ .............................. kPa |
| 5.2.3. | Tyre/wheel combinations: ........................................................ |
| 5.2.4. | Minimum-speed category symbol compatible with the theoretical maximum design speed of the vehicle: ....................................................................... |
| 5.2.5. | Minimum load-capacity index with the maximum load on each tyre: ........................................................................... |
| 5.2.6. | Categories of use compatible for the vehicle: .......................................... |
| 6. | Steering |
| 6.1. | Steering gear and control |
| 6.1.1. | Type of gear: ........................................................................... |
| 6.1.2. | Brief description of the electrical and/or electronic components used in the steering system: ..................................................... |
| 7. | Braking |
| 7.1. | Diagram of braking devices: .................................................... |
| 7.2. | Front and rear brakes, disc and/or drum <*> |
| 7.2.1. | Make(s): .................................................................................. |
| 7.2.2. | Type(s): ................................................................................. |
| 7.3. | Drawing of parts of the brake system |
| 7.3.1. | Shoes and/or pads <*> |
| 7.3.2. | Linings and/or pads (Indicate make, grade of material or identification mark) <*>: .......................................................... |
| 7.3.3. | Brake levers and/or pedals <*>: ............................................... |
| 7.3.4. | Hydraulic reservoirs (where applicable): ................................. |
| 7.4. | Other devices (where applicable): drawing and description: ................................................................................................ |
| 7.5. | Brief description of the electrical and/or electronic components used in the braking system: ....................................................... |
| 8. | Lighting and light-signalling devices |
| 8.1. | List of all devices (mentioning the number, make(s), model, component type-approval mark(s), the maximum intensity of the main-beam headlamps, colour, the corresponding tell-tale): .................................................... |
| 8.2. | Diagram showing the location of the lighting and light-signalling devices: .................................................................................. |
| 8.3. | Hazard warning lamps (where fitted): ........................................ |
| 8.4. | Additional requirements relating to special vehicles: .......................................................... |
| 8.5. | Brief description of the electrical and/or electronic components used in the lighting system and in the light-signalling system: .......................................................... |
| 9. | Equipment |
| 9.1. | Coupling devices (where applicable) |
| 9.1.1. | Type: hook/ring/other <*> |
| 9.1.2. | Photograph and/or drawings showing the position and the construction of the coupling devices: ....................................... |
| 9.2. | Arrangement and identification of controls, tell-tales and indicators: .............................................................................. |
| 9.2.1. | Photographs and/or drawings of the arrangement of the symbols, controls, tell-tales and indicators: ............................................. |
| 9.3. | Statutory inscriptions |
| 9.3.1. | Photographs and/or drawings showing the location of the statutory inscriptions and the chassis number: .................................................................... |
| 9.3.2. | Photographs and/or drawings showing the official part of the inscription (with statement of dimensions): ..................................................................................... |
| 9.3.3. | Photographs and/or drawings of the chassis number (with statement of dimensions): ......................................................... |
| 9.4. | Device(s) to protect against unauthorised use: |
| 9.4.1. | Type of device(s) |
| 9.4.2. | Summary description of device(s) used: ................................... |
| 9.5. | Audible warning device(s) |
| 9.5.1. | Summary description of device(s) used and their purpose: ................................ |
| 9.5.2. | Make(s): ................................................................................. |
| 9.5.3. | Type(s): .................................................................................. |
| 9.5.4. | Type-approval mark: ............................................................... |
| 9.5.5. | Drawing(s) showing the location of the audible warning device(s) in relation to the structure of the vehicle: ............................................................................................... |
| 9.5.6. | Details of the method of attachment, including the part of the vehicle structure to which the audible warning device(s) is (are) attached: ........................................................................... |
| 9.6. | Location of rear registration plate (indicate variants where necessary; drawings may be used as appropriate): ................................................................................................ |
| 9.6.1. | Inclination of plane in relation to the vertical: ........................... |
| B. | INFORMATION RELATING SOLELY TO TWO-WHEEL MOPEDS AND MOTORCYCLES |
| 1. | Equipment |
| 1.1. | Rear-view mirror(s) (please provide the following information for each rear-view mirror) |
| 1.1.1. | Make: ...................................................................................... |
| 1.1.2. | Component type-approval mark: ............................................. |
| 1.1.3. | Variant: .................................................................................. |
| 1.1.4. | Drawing(s) showing the location of the rear-view mirror(s) in relation to the structure of the vehicle: ...................................... |
| 1.1.5. | Precise information concerning the type of attachment, including that part of the vehicle structure to which the rear-view mirror is attached: ............................................................................. |
| 1.2. | Stand |
| 1.2.1. | Type: central and/or side <*> |
| 1.2.2. | Drawing showing the location of the stand(s) in relation to the structure of the vehicle: ........................................................... |
| 1.3. | Attachments for motorcycle sidecars (where applicable) |
| 1.3.1. | Photographs and/or drawings showing the location and the construction: ........................................................................... |
| 1.4. | Hand-hold for a passenger |
| 1.4.1. | Type: strap and/or handle <*> |
| 1.4.2. | Photographs and/or drawings showing the location: ............................................................................................. |
| 1.5. | For mopeds fitted with pedals and, if Directive 97/24/EC, Chapter 3, Annex I, point 3.5 applies, description of the measures taken in order to ensure safety: ................................... |
| 1.6 | Design and position of the label referred to in Directive 97/24/EC, Chapter 7: .............................................................. |
| C. | INFORMATION RELATING SOLELY TO THREE-WHEEL MOPEDS, MOTOR TRICYCLES AND QUADRICYCLES |
| 1. | Dimensions and masses (in mm and kg) (where necessary, refer to drawings) |
| 1.1. | Dimensions to be complied with when building unbodied chassis |
| 1.1.1. | Length: ................................................................................... |
| 1.1.2. | Width: .................................................................................... |
| 1.1.3. | Unladen height: ....................................................................... |
| 1.1.4. | Front overhang: ....................................................................... |
| 1.1.5. | Rear overhang: ....................................................................... |
| 1.1.6. | Limit position for centre of gravity of bodied vehicle: ................................... |
| 1.2. | Masses d |
| 1.2.1. | Maximum payload declared by manufacturer: ......................................................... |
| 2. | Equipment |
| 2.1. | Bodywork |
| 2.1.1. | Nature of bodywork: .............................................................. |
| 2.1.2. | General dimensional arrangement drawing of inside: .............................................................................................. |
| 2.1.3. | General dimensional arrangement drawing of outside: ............................................................................................... |
| 2.1.4. | Materials and methods of manufacture: ............................................................................................... |
| 2.1.5. | Passenger doors, locks and hinges: ............................................................................................. |
| 2.1.6. | Configuration, dimensions, direction and maximum opening angle of doors: ...................................................................... |
| 2.1.7. | Drawing of locks and hinges and their location in the doors: ................................................................................................ |
| 2.1.8. | Technical description of locks and hinges: .............................................................................................. |
| 2.2. | Windscreen and other glazing |
| 2.2.1. | Windscreen |
| 2.2.1.1. | Materials used: ......................................................................... |
| 2.2.2. | Other glazing |
| 2.2.2.1. | Materials used: ......................................................................... |
| 2.3. | Windscreen wiper(s) |
| 2.3.1. | Detailed technical description (with photographs or drawings): ............................................................................................. |
| 2.4. | Windscreen washer(s) |
| 2.4.1. | Detailed technical description (with photographs or drawings): ............................................................................................... |
| 2.5. | Defrosting and demisting |
| 2.5.1. | Detailed technical description (with photographs or drawings): ............................................................................................... |
| 2.6. | Rear-view mirror(s) (please give the following information for each rear-view mirror) |
| 2.6.1. | Make: ..................................................................................... |
| 2.6.2. | Type-approval mark ............................................................... |
| 2.6.3. | Variant: ................................................................................. |
| 2.6.4. | Drawing(s) showing the location of the rear-view mirror(s) in relation to the structure of the vehicle: ....................................... |
| 2.6.5. | Detailed information on the method of attachment, including that part of the structure of the vehicle to which the rear-view mirror is attached: ............................................................................ |
| 2.7. | Seats |
| 2.7.1. | Number: ................................................................................. |
| 2.7.2. | Location: ................................................................................ |
| 2.7.3. | Coordinates or drawing of the R point <j> |
| 2.7.3.1. | Driving seat: ........................................................................... |
| 2.7.3.2. | Other seats: ............................................................................. |
| 2.7.4. | Intended seat-back inclination |
| 2.7.4.1. | Driving seat: ........................................................................... |
| 2.7.4.2. | Other seats: ............................................................................ |
| 2.7.5. | Seat adjustment range, where appropriate |
| 2.7.5.1. | Driving seat: ............................................................................ |
| 2.7.5.2. | Other seats: ............................................................................ |
| 2.8. | Passenger-compartment heating system (where applicable) |
| 2.8.1. | Summary description of type of vehicle in respect of the heating system if this uses heat from the liquid engine coolant: ............................................................................................. |
| 2.8.2. | Detailed description of the type of the vehicle in respect of the heating system if this uses the cooling air or exhaust gases as a heat source, including: |
| 2.8.2.1. | An overall drawing of the heating system giving its location on the vehicle (and the arrangement of the sound damping devices (including the position of the heat exchange points)): ................. |
| 2.8.2.2. | An overall drawing of the heat exchanger used in systems utilising the heat from the exhaust gases, or of the parts where that exchange takes place (in the case of heating systems using the heat provided by the engine cooling air): ............................. |
| 2.8.2.3. | A sectional drawing of the heat exchanger or parts where heat exchange takes place, together with a statement of the wall thickness, of the materials used and the characteristics of their surface: .................................................................................. |
| 2.8.2.4. | Specifications regarding the method of manufacture and technical data relating to other major components of the heating system, such as the fan: .......................................................... |
| 2.9. | Safety belts |
| 2.9.1. | Number and location of safety belts, together with a reference to the seats where that type of equipment may be installed: ............................................................................................... |
| D/P | Complete type-approval mark | Variant (if any) |
| Front seats |
| ................................................................................................ |
| ................................................................................................ |
| ............................................................................................... |
| Rear seats |
| ................................................................................................ |
| ............................................................................................... |
| ............................................................................................... |
| Centre rear and centre front seats |
| ............................................................................................... |
| ............................................................................................... |
| ................................................................................................ |
| Special devices (example: seat height adjustment, preloading device, etc.) |
| .............................................................................................. |
| ............................................................................................... |
| ................................................................................................ |
| --------------------------------
D = drivers's side.
P = front passenger side. |
| 2.10. | Anchorages |
| 2.10.1. | Number and location of the anchorages: .................................... |
| 2.10.2. | Photographs and/or drawings of the bodywork showing the true, effective location and dimensions of the anchorages, together with an indication of the R-point position: ................................ |
|
| 2.10.3. | Drawings of the anchorages and the parts of the structure of the vehicle to which they are attached (together with a statement of the nature of the materials used): .............................................. |
|
| 2.10.4. | Designation of the types of belts <*> authorised for attachment to the anchorages on the vehicle: |
| Location of anchorage |
| Structure of vehicle | Structure of seat |
| Front | | | |
 |  |
 |  | | |
 |  | | |
| Rear | | | |
 |  |
 |  | | |
 |  | | |
(*) "A": for a three-point belt.
"B": for a lap belt.
"S": for special types of belt (in this case provide specific information on the nature of these types under observation).
"Ar", "Br" or "Sr": for a belt incorporating an inertia reel.
"Are", "Bre" and "Sre": for a belt equipped with an inertia reel and an energy-absorption device on at least one anchorage. |
| 2.10.5. | Description of a specific type of belt, one anchorage of which is attached to the seat back-rest or incorporates an energy-dissipation device: ....................................................... |
